During PERST# assertion tegra_pcie_bpmp_set_pll_state() is currently
called twice.
pex_ep_event_pex_rst_assert() should do the opposite of
pex_ep_event_pex_rst_deassert(), so it is obvious that the duplicate
tegra_pcie_bpmp_set_pll_state() is a mistake, and that the duplicate
tegra_pcie_bpmp_set_pll_state() call should instead be a call to
tegra_pcie_bpmp_set_ctrl_state().
With this, the uninitialization sequence also matches that of
tegra_pcie_unconfig_controller().
Fixes: a54e190737 ("PCI: tegra194: Add Tegra234 PCIe support")
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
[cassel: improve commit log]
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Link: https://patch.msgid.link/20250911093021.1454385-2-cassel@kernel.org
[mani: added Fixes tag]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Add support for PCIe controller in Sophgo SG2042 SoC. The controller uses
the Cadence PCIe core programmed by pcie-cadence* common driver. The PCIe
controller in SG2042 works in host mode only, supporting data rate up to 16
GT/s and lanes up to x16 or x8.
Signed-off-by: Chen Wang <unicorn_wang@outlook.com>
[mani: reworded description and minor code cleanups]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://patch.msgid.link/01b0a57cd9dba8bed7c1f2d52997046c2c6f042b.1757643388.git.unicorn_wang@outlook.com
cdns_pcie::ops might not be populated by all the Cadence glue drivers. This
is going to be true for the upcoming Sophgo platform which doesn't set the
ops.
Hence, add a check to prevent NULL pointer dereference.
Signed-off-by: Chen Wang <unicorn_wang@outlook.com>
[mani: reworded subject and description]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://patch.msgid.link/35182ee1d972dfcd093a964e11205efcebbdc044.1757643388.git.unicorn_wang@outlook.com
DT binding allows specifying 'phy' and 'reset' properties in both host
bridge and Root Port nodes, though specifying in the host bridge node is
marked as deprecated. Still, the pcie-qcom driver should support both
combinations for maintaining the DT backwards compatibility. For this
purpose, the driver is holding the relevant pointers of these properties in
two structs: struct qcom_pcie_port and struct qcom_pcie.
However, this causes confusion and increases the driver complexity. Hence,
move the pointers from struct qcom_pcie to struct qcom_pcie_port. As a
result, even if these properties are specified in the host bridge node,
the pointers will be stored in struct qcom_pcie_port as if the properties
are specified in a single Root Port node. This logic simplifies the driver
a lot.
Suggested-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@oss.qualcomm.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20250912-pci-pwrctrl-perst-v3-2-3c0ac62b032c@oss.qualcomm.com
dw_pcie_edma_irq_verify() already parses device tree for either "dma" (if
there is a single IRQ for all DMA channels) or "dmaX" (if there is one IRQ
per DMA channel), and initializes dma.nr_irqs accordingly.
Additionally, the probing of the eDMA driver will fail if neither "dma"
nor "dmaX" is defined in the device tree.
Therefore there is no need for a glue driver to specify edma.nr_irqs, so
remove the redundant edma.nr_irqs initialization.
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
[bhelgaas: fix typos]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20250908165914.547002-4-cassel@kernel.org
dw_pcie_edma_irq_verify() is supposed to verify the eDMA IRQs in devicetree
by fetching them using either 'dma' or 'dmaX' IRQ names. Former is used
when the platform uses a single IRQ for all eDMA channels and latter is
used when the platform uses separate IRQ per channel. But currently,
dw_pcie_edma_irq_verify() bails out early if edma::nr_irqs is 1, i.e., when
a single IRQ is used. This gives an impression that the driver could work
with any single IRQ in devicetree, not necessarily with name 'dma'.
But dw_pcie_edma_irq_vector(), which actually requests the IRQ, does
require the single IRQ to be named as 'dma'. So this creates inconsistency
between dw_pcie_edma_irq_verify() and dw_pcie_edma_irq_vector().
Thus, to fix this inconsistency, make sure dw_pcie_edma_irq_verify() also
verifies the single IRQ name by removing the bail out code.
Signed-off-by: Niklas Cassel <cassel@kernel.org>
[mani: reworded subject and description]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
[bhelgaas: fix typos]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20250908165914.547002-3-cassel@kernel.org
5da3d94a23 ("PCI: mvebu: Use for_each_of_range() iterator for parsing
"ranges"") simplified code by using the for_each_of_range() iterator, but
it broke PCI enumeration on Turris Omnia (and probably other mvebu
targets).
Issue #1:
To determine range.flags, of_pci_range_parser_one() uses bus->get_flags(),
which resolves to of_bus_pci_get_flags(), which already returns an
IORESOURCE bit field, and NOT the original flags from the "ranges"
resource.
Then mvebu_get_tgt_attr() attempts the very same conversion again. Remove
the misinterpretation of range.flags in mvebu_get_tgt_attr(), to restore
the intended behavior.
Issue #2:
The driver needs target and attributes, which are encoded in the raw
address values of the "/soc/pcie/ranges" resource. According to
of_pci_range_parser_one(), the raw values are stored in range.bus_addr and
range.parent_bus_addr, respectively. range.cpu_addr is a translated version
of range.parent_bus_addr, and not relevant here.
Use the correct range structure member, to extract target and attributes.
This restores the intended behavior.
Fixes: 5da3d94a23 ("PCI: mvebu: Use for_each_of_range() iterator for parsing "ranges"")
Reported-by: Jan Palus <jpalus@fastmail.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=220479
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Tony Dinh <mibodhi@gmail.com>
Tested-by: Jan Palus <jpalus@fastmail.com>
Link: https://patch.msgid.link/20250907102303.29735-1-klaus.kudielka@gmail.com
The Cadence PCIe Controller integrated in the TI K3 SoCs supports both
Root-Complex and Endpoint modes of operation. The Glue Layer allows
"strapping" the Mode of operation of the Controller, the Link Speed
and the Link Width. This is enabled by programming the "PCIEn_CTRL"
register (n corresponds to the PCIe instance) within the CTRL_MMR
memory-mapped register space. The "reset-values" of the registers are
also different depending on the mode of operation.
Since the PCIe Controller latches onto the "reset-values" immediately
after being powered on, if the Glue Layer configuration is not done while
the PCIe Controller is off, it will result in the PCIe Controller latching
onto the wrong "reset-values". In practice, this will show up as a wrong
representation of the PCIe Controller's capability structures in the PCIe
Configuration Space. Some such capabilities which are supported by the PCIe
Controller in the Root-Complex mode but are incorrectly latched onto as
being unsupported are:
- Link Bandwidth Notification
- Alternate Routing ID (ARI) Forwarding Support
- Next capability offset within Advanced Error Reporting (AER) capability
Fix this by powering off the PCIe Controller before programming the "strap"
settings and powering it on after that. The runtime PM APIs namely
pm_runtime_put_sync() and pm_runtime_get_sync() will decrement and
increment the usage counter respectively, causing GENPD to power off and
power on the PCIe Controller.
Fixes: f3e25911a4 ("PCI: j721e: Add TI J721E PCIe driver")
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250908120828.1471776-1-s-vadapalli@ti.com
The dev_err_probe() doesn't do anything when error is '-ENOMEM'.
Therefore, remove the useless call to dev_err_probe(), and just
return the value instead.
Signed-off-by: Xichao Zhao <zhao.xichao@vivo.com>
[mani: reworded the subject]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
The 'info' parameter of hv_msi_free() is unused. Delete it.
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Acked-by: Wei Liu <wei.liu@kernel.org>
When the 3.3Vaux supply is present, fetch it at the probe time and keep it
enabled for the entire PCIe controller lifecycle so that the link can enter
L2 state and the devices can signal wakeup using either Beacon or WAKE#
mechanisms.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
[mani: reworded the subject, description and error message]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20250820022328.2143374-1-hongxing.zhu@nxp.com
Add lane equalization setting for 8.0 GT/s and 32.0 GT/s to enhance link
stability and avoid AER Correctable Errors reported on some platforms
(eg. SA8775P).
8.0 GT/s, 16.0 GT/s and 32.0 GT/s require the same equalization setting.
This setting is programmed into a group of shadow registers, which can be
switched to configure equalization for different speeds by writing 00b,
01b and 10b to `RATE_SHADOW_SEL`.
Hence, program equalization registers in a loop using link speed as index,
so that equalization setting can be programmed for 8.0 GT/s, 16.0 GT/s
and 32.0 GT/s.
Fixes: 489f14be0e ("arm64: dts: qcom: sa8775p: Add pcie0 and pcie1 nodes")
Co-developed-by: Qiang Yu <qiang.yu@oss.qualcomm.com>
Signed-off-by: Qiang Yu <qiang.yu@oss.qualcomm.com>
Signed-off-by: Ziyue Zhang <ziyue.zhang@oss.qualcomm.com>
[mani: wrapped the warning to fit 100 columns, used post-increment for loop]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://patch.msgid.link/20250904065225.1762793-2-ziyue.zhang@oss.qualcomm.com
Fix incorrect argument order in devm_kcalloc() when allocating port->phys.
The original call used sizeof(phy) as the number of elements and
port->lanes as the element size, which is reversed. While this happens to
produce the correct total allocation size with current pointer size and
lane counts, the argument order is wrong.
Fixes: 6fe7c187e0 ("PCI: tegra: Support per-lane PHYs")
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
[mani: added Fixes tag]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20250819150436.3105973-1-alok.a.tiwari@oracle.com
The era of hand-rolled HIWORD_UPDATE macros is over.
Like many other Rockchip drivers, pcie-dw-rockchip brings with it its
very own flavour of HIWORD_UPDATE. It's occasionally used without a
constant mask, which complicates matters. HIWORD_UPDATE_BIT is a
confusingly named addition, as it doesn't update the bit, it actually
sets all bits in the value to 1. HIWORD_DISABLE_BIT is similarly
confusing; it disables several bits at once by using the value as a mask
and the inverse of value as the value, and the "disabling only these"
effect comes from the hardware actually using the mask. The more obvious
approach would've been HIWORD_UPDATE(val, 0) in my opinion.
This is part of the motivation why this patch uses hw_bitfield.h's
FIELD_PREP_WM16 instead, where possible. FIELD_PREP_WM16 requires a
constant bit mask, which isn't possible where the irq number is used to
generate a bit mask. For that purpose, we replace it with a more robust
macro than what was there but that should also bring close to zero
runtime overhead: we actually mask the IRQ number to make sure we're not
writing garbage.
For the remaining bits, there also are some caveats. For starters, the
PCIE_CLIENT_ENABLE_LTSSM and PCIE_CLIENT_DISABLE_LTSSM were named in a
manner that isn't quite truthful to what they do. Their modification
actually spans not just the LTSSM bit but also another bit, flipping
only the LTSSM one, but keeping the other (which according to the TRM
has a reset value of 0) always enabled. This other bit is reserved as of
the IP version RK3588 uses at least, and I have my doubts as to whether
it was meant to be set, and whether it was meant to be set in that code
path. Either way, it's confusing.
Replace it with just writing either 1 or 0 to the LTSSM bit, using the
new FIELD_PREP_WM16 macro from hw_bitfield.h, which grants us the
benefit of better compile-time error checking.
The change of no longer setting the reserved bit doesn't appear to
change the behaviour on RK3568 in RC mode, where it's not marked as
reserved.
PCIE_CLIENT_RC_MODE/PCIE_CLIENT_EP_MODE was another field that wasn't
super clear on what the bit field modification actually is. As far as I
can tell, switching to RC mode doesn't actually write the correct value
to the field if any of its bits have been set previously, as it only
updates one bit of a 4 bit field.
Replace it by actually writing the full values to the field, using the
new FIELD_PREP_WM16 macro, which grants us the benefit of better
compile-time error checking.
This patch was tested on RK3588 (PCIe3 x4 controller), RK3576 (PCIe2 x1
controller) and RK3568 (PCIe x2 controller), all in RC mode.
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Yury Norov (NVIDIA) <yury.norov@gmail.com>
The era of hand-rolled HIWORD_UPDATE macros is over, at least for those
drivers that use constant masks.
The Rockchip PCI driver, like many other Rockchip drivers, has its very
own definition of HIWORD_UPDATE.
Remove it, and replace its usage with either FIELD_PREP_WM16, or two new
header local macros for setting/clearing a bit with the high mask, which
use FIELD_PREP_WM16_CONST internally. In the process, ENCODE_LANES
needed to be adjusted, as FIELD_PREP_WM16* shifts the value for us.
That this is equivalent was verified by first making all FIELD_PREP_WM16
instances FIELD_PREP_WM16_CONST, then doing a static_assert() comparing
it to the old macro (and for those with parameters, static_asserting for
the full range of possible values with the old encode macro).
What we get out of this is compile time error checking to make sure the
value actually fits in the mask, and that the mask fits in the register,
and also generally less icky code that writes shifted values when it
actually just meant to set and clear a handful of bits.
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Yury Norov (NVIDIA) <yury.norov@gmail.com>
Commit a2790bf81f ("PCI: j721e: Add support to build as a loadable
module") added support to build the driver as a loadable module. However,
it did not add MODULE_DEVICE_TABLE() which is required for autoloading the
driver based on device table when it is built as a loadable module.
Fix it by adding MODULE_DEVICE_TABLE.
Fixes: a2790bf81f ("PCI: j721e: Add support to build as a loadable module")
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
[mani: reworded description]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250901120359.3410774-1-s-vadapalli@ti.com
The qcom_pcie_parse_ports() function currently iterates over all available
child nodes of the PCIe controller's device tree node. This includes
unrelated nodes such as OPP (Operating Performance Points) nodes, which do
not contain the expected 'reset' and 'phy' properties. As a result, parsing
fails and the driver falls back to the legacy method of parsing the
controller node directly. However, this fallback also fails when properties
are shifted to the Root Port node, leading to probe failure.
Fix this by restricting the parsing logic to only consider child nodes with
device_type = "pci", which is the expected and required property for PCIe
bridge nodes as per the pci-bus-common.yaml dtschema.
Fixes: a2fbecdbbb ("PCI: qcom: Add support for parsing the new Root Port binding")
Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
[mani: reworded subject and description]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://patch.msgid.link/20250826-pakala-v3-3-721627bd5bb0@oss.qualcomm.com
Replace calls of devm_kzalloc() with devm_kcalloc() in ks_pcie_probe().
As noted in the kernel documentation [1], open-coded multiplication in
allocator arguments is discouraged because it can lead to integer
overflow.
Using devm_kcalloc() provides built-in overflow protection, making the
memory allocation safer when calculating the allocation size compared
to explicit multiplication.
[1]: https://www.kernel.org/doc/html/next/process/deprecated.html#open-coded-arithmetic-in-allocator-arguments
Signed-off-by: Qianfeng Rong <rongqianfeng@vivo.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://patch.msgid.link/20250819131235.152967-1-rongqianfeng@vivo.com
Starting with commit dd26c1a23f ("PCI: rcar-host: Switch to
msi_create_parent_irq_domain()"), the MSI parent IRQ domain is NULL because
the object of type struct irq_domain_info passed to:
msi_create_parent_irq_domain() ->
irq_domain_instantiate()() ->
__irq_domain_instantiate()
has no reference to the parent IRQ domain. Using msi->domain->parent as an
argument for generic_handle_domain_irq() leads to below error:
"Unable to handle kernel NULL pointer dereference at virtual address"
This error was identified while switching the upcoming RZ/G3S PCIe host
controller driver to msi_create_parent_irq_domain() (which was using a
similar pattern to handle MSIs (see link section)), but it was not tested
on hardware using the pcie-rcar-host controller driver due to lack of
hardware.
Fixes: dd26c1a23f ("PCI: rcar-host: Switch to msi_create_parent_irq_domain()")
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
[mani: reworded subject and description]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Nam Cao <namcao@linutronix.de>
Link: https://lore.kernel.org/all/20250704161410.3931884-6-claudiu.beznea.uj@bp.renesas.com
Link: https://patch.msgid.link/20250809144447.3939284-1-claudiu.beznea.uj@bp.renesas.com
The PCI capability/extended capability offsets are not guaranteed to be the
same across all SoCs integrating the Cadence PCIe IP.
Use the cdns_pcie_find_{ext}_capability() APIs to find the capabilities,
which avoids hardcoding the offsets in the driver.
Signed-off-by: Hans Zhang <18255117159@163.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Acked-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://patch.msgid.link/20250813144529.303548-7-18255117159@163.com
The PCI core now provides generic PCI_FIND_NEXT_CAP() and
PCI_FIND_NEXT_EXT_CAP() macros to search for PCI capabilities, using
config accessors we supply.
Use them in the CDNS driver to add cdns_pcie_find_capability() and
cdns_pcie_find_ext_capability() interfaces.
Signed-off-by: Hans Zhang <18255117159@163.com>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20250813144529.303548-6-18255117159@163.com
The PCI core now provides generic PCI_FIND_NEXT_CAP() macros to search for
PCI capabilities, using config accessors we supply.
Use them in the DWC EP driver to implement dw_pcie_ep_find_capability()
instead of duplicating the algorithm.
Signed-off-by: Hans Zhang <18255117159@163.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20250819145828.438541-1-18255117159@163.com
Introduce support for the PCI-Express Gen3 controller found in the
MT8196 (and MT6991) SoC by adding a compatible string and platform
specific data.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://patch.msgid.link/20250703120847.121826-4-angelogioacchino.delregno@collabora.com
In preparation to add support for the PCI-Express Gen3 controller
found in newer MediaTek SoCs, such as the Dimensity 9400 MT6991
and the MT8196 Chromebook SoC, add the definition for the PCIE
Resource Control register and a new sys_clk_rdy_time_us variable
in platform data.
If sys_clk_rdy_time_us is found (> 0), set the new value in the
aforementioned register only after configuring the controller to
RC mode, as this may otherwise be reset.
Overriding the register defaults for SYS_CLK_RDY_TIME allows to
work around sys_clk_rdy signal glitching in MT6991 and MT8196.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
[mani: used FIELD_MODIFY() to simplify mask and update]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://patch.msgid.link/20250703120847.121826-2-angelogioacchino.delregno@collabora.com
The PCI core now provides generic PCI_FIND_NEXT_CAP() and
PCI_FIND_NEXT_EXT_CAP() macros to search for PCI capabilities, using
config accessors we supply.
Use them in the DWC driver to implement dw_pcie_find_capability() and
dw_pcie_find_ext_capability() instead of duplicating the algorithm.
Signed-off-by: Hans Zhang <18255117159@163.com>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20250813144529.303548-5-18255117159@163.com
d7d8ab87e3 ("PCI: vmd: Switch to msi_create_parent_irq_domain()") added a
WARN_ON sanity check that child devices support MSI-X, because VMD document
says [1]:
Intel VMD only supports MSIx Interrupts from child devices and therefore
the BIOS must enable PCIe Hot Plug and MSIx interrups [sic].
However, the VMD device can't even tell the difference between a child
device using MSI and one using MSI-X. Per 185a383ada ("x86/PCI: Add
driver for Intel Volume Management Device (VMD)"), VMD does not support
INTx interrupts, but does support child devices using either MSI or MSI-X.
Remove the sanity check to avoid the WARN_ON and allow child devices to use
MSI, reported by Ammar.
Fixes: d7d8ab87e3 ("PCI: vmd: Switch to msi_create_parent_irq_domain()")
Link: https://cdrdv2-public.intel.com/776857/VMD_White_Paper.pdf [1]
Reported-by: Ammar Faizi <ammarfaizi2@gnuweeb.org>
Closes: https://lore.kernel.org/linux-pci/aJXYhfc%2F6DfcqfqF@linux.gnuweeb.org/
Signed-off-by: Nam Cao <namcao@linutronix.de>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Ammar Faizi <ammarfaizi2@gnuweeb.org>
Link: https://patch.msgid.link/20250811053935.4049211-1-namcao@linutronix.de
f29861aa30 ("PCI: xilinx: Switch to msi_create_parent_irq_domain()")
changed xilinx_pcie::msi_domain from child devices' interrupt domain to
Xilinx AXI bridge's interrupt domain.
However, xilinx_pcie_intr_handler() wasn't changed and still reads Xilinx
AXI bridge's interrupt domain from xilinx_pcie::msi_domain->parent. This
pointer is NULL now.
Update xilinx_pcie_intr_handler() to read the correct interrupt domain
pointer.
Fixes: f29861aa30 ("PCI: xilinx: Switch to msi_create_parent_irq_domain()")
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20250811054144.4049448-1-namcao@linutronix.de
There is a typo so we accidentally return positive EINVAL instead of
negative -EINVAL. Add the missing '-' character.
Fixes: 6aceb36f17 ("PCI: xgene-msi: Restructure handler setup/teardown")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://patch.msgid.link/aIzCbVd93ivPinne@stanley.mountain
Add support for handling the AMD Versal Gen 2 MDB PCIe Root Port PERST#
signal via a GPIO by parsing the new PCIe bridge node to acquire the
reset GPIO. If the bridge node is not found, fall back to acquiring it
from the PCIe host bridge node.
As part of this, update the interrupt controller node parsing to use
of_get_child_by_name() instead of of_get_next_child(), since the PCIe
host bridge node now has multiple children. This ensures the correct
node is selected during initialization.
Signed-off-by: Sai Krishna Musham <sai.krishna.musham@amd.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://patch.msgid.link/20250807074019.811672-3-sai.krishna.musham@amd.com
R-Car V4H Reference Manual R19UH0186EJ0130 Rev.1.30 Apr. 21, 2025 page 4581
Figure 104.3b Initial Setting of PCIEC(example), middle of the figure
indicates that fourth write into register 0x148 [2:0] is 0x3 or
GENMASK(1, 0). The current code writes GENMASK(11, 0) which is a typo. Fix
the typo.
Fixes: faf5a975ee ("PCI: rcar-gen4: Add support for R-Car V4H")
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250806192548.133140-1-marek.vasut+renesas@mailbox.org
Select the pwrctrl driver, which is utilized to manage the power supplies
of the devices connected to the standard PCI slots conforming to
specification like PCIe CEM. This ensures that the voltage rails of the
standard PCI slots on some platforms eg. X1E80100-QCP can be correctly
turned on/off if they are described in PCIe Root Port device tree node.
Signed-off-by: Qiang Yu <qiang.yu@oss.qualcomm.com>
Signed-off-by: Wenbin Yao <quic_wenbyao@quicinc.com>
[mani: reworded subject and description]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://patch.msgid.link/20250722091151.1423332-2-quic_wenbyao@quicinc.com
vmd_msi_alloc() allocates struct vmd_irq and stashes it into
irq_data->chip_data associated with the VMD's interrupt domain.
vmd_msi_free() extracts the pointer by calling irq_get_chip_data() and
frees it.
irq_get_chip_data() returns the chip_data associated with the top interrupt
domain. This worked in the past because VMD's interrupt domain was the top
domain.
But d7d8ab87e3 ("PCI: vmd: Switch to msi_create_parent_irq_domain()")
changed the interrupt domain hierarchy so VMD's interrupt domain is not the
top domain anymore. irq_get_chip_data() now returns the chip_data at the
MSI devices' interrupt domains. It is therefore broken for vmd_msi_free()
to kfree() this chip_data.
Fix by extracting the chip_data associated with the VMD's interrupt domain.
Fixes: d7d8ab87e3 ("PCI: vmd: Switch to msi_create_parent_irq_domain()")
Reported-by: Kenneth Crudup <kenny@panix.com>
Closes: https://lore.kernel.org/linux-pci/dfa40e48-8840-4e61-9fda-25cdb3ad81c1@panix.com/
Reported-by: Ammar Faizi <ammarfaizi2@gnuweeb.org>
Closes: https://lore.kernel.org/linux-pci/ed53280ed15d1140700b96cca2734bf327ee92539e5eb68e80f5bbbf0f01@linux.gnuweeb.org/
Tested-by: Ammar Faizi <ammarfaizi2@gnuweeb.org>
Tested-by: Kenneth Crudup <kenny@panix.com>
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jinjie Ruan <ruanjinjie@huawei.com>
Acked-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://patch.msgid.link/20250807081051.2253962-1-namcao@linutronix.de
-----BEGIN PGP SIGNATURE-----
iQJIBAABCgAyFiEEgMe7l+5h9hnxdsnuWYigwDrT+vwFAmiL3OkUHGJoZWxnYWFz
QGdvb2dsZS5jb20ACgkQWYigwDrT+vz9bhAAqiD9REYlNUgGX/bEBgCVPFdtjjTz
FpSLzG23vWd2J0FEy04qtQWH9j71IXnM+yMybzsMe9SsPt2HhczzSCIMpPj0FZNN
ccOf3gA/KqPux7FORrS3mpM8OO4ICt3XZhCji3nNg5iW5XlH+NrQKPVxRlvBB0rP
+7RxSjDClUdZ97QSSmp1uZ7Qh1qyV0Ht0qjPMwecrnB2kApt4ZaMphAaKPEjX/4f
RgZPFqbIpRWt9e87Z8ADr5c2jokZAzIV0zauQ2fhbjBkTcXIXL3yOzUbR+ngBWDD
oq21rXJBUCQheA7J6j2SKabgF9AZaI5NI9ERld5vJ1inXSZCyuyKopN1AzuKZquG
N+jyYJqZC99ePvMLbTWs/spU58J03A6TOwaJNE3ISRgbnxFkhvLl7h68XuTDonZm
hYGloXXUj+i+rh7/eJIDDWa9MTpEvl2p1zc6EDIZ/umlnHwg9rGlGQVARMCs6Ist
EiJQEtjMMlXiBJMkFhpxesOdyonGkxAL9WtT6MoEOFF7dqgsTqSKiDUPa+6MHV+I
tsTB630J3ROsWGfQD1uJI2BrCm+op4j6faamH6UMqCrUU0TUZMHiRR3qVWbM6qgU
/WL1gZ96uy5I7UoE0+gH+wMhMClO2BnsxffocToDE5wOYpGDd5BwPEoY8ej8U2lu
CBMCkMor1jDtS8Y=
=ipv3
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.17-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Allow built-in drivers, not just modular drivers, to use async
initial probing (Lukas Wunner)
- Support Immediate Readiness even on devices with no PM Capability
(Sean Christopherson)
- Consolidate definition of PCIE_RESET_CONFIG_WAIT_MS (100ms), the
required delay between a reset and sending config requests to a
device (Niklas Cassel)
- Add pci_is_display() to check for "Display" base class and use it
in ALSA hda, vfio, vga_switcheroo, vt-d (Mario Limonciello)
- Allow 'isolated PCI functions' (multi-function devices without a
function 0) for LoongArch, similar to s390 and jailhouse (Huacai
Chen)
Power control:
- Add ability to enable optional slot clock for cases where the PCIe
host controller and the slot are supplied by different clocks
(Marek Vasut)
PCIe native device hotplug:
- Fix runtime PM ref imbalance on Hot-Plug Capable ports caused by
misinterpreting a config read failure after a device has been
removed (Lukas Wunner)
- Avoid creating a useless PCIe port service device for pciehp if the
slot is handled by the ACPI hotplug driver (Lukas Wunner)
- Ignore ACPI hotplug slots when calculating depth of pciehp hotplug
ports (Lukas Wunner)
Virtualization:
- Save VF resizable BAR state and restore it after reset (Michał
Winiarski)
- Allow IOV resources (VF BARs) to be resized (Michał Winiarski)
- Add pci_iov_vf_bar_set_size() so drivers can control VF BAR size
(Michał Winiarski)
Endpoint framework:
- Add RC-to-EP doorbell support using platform MSI controller,
including a test case (Frank Li)
- Allow BAR assignment via configfs so platforms have flexibility in
determining BAR usage (Jerome Brunet)
Native PCIe controller drivers:
- Convert amazon,al-alpine-v[23]-pcie, apm,xgene-pcie,
axis,artpec6-pcie, marvell,armada-3700-pcie, st,spear1340-pcie to
DT schema format (Rob Herring)
- Use dev_fwnode() instead of of_fwnode_handle() to remove OF
dependency in altera (fixes an unused variable), designware-host,
mediatek, mediatek-gen3, mobiveil, plda, xilinx, xilinx-dma,
xilinx-nwl (Jiri Slaby, Arnd Bergmann)
- Convert aardvark, altera, brcmstb, designware-host, iproc,
mediatek, mediatek-gen3, mobiveil, plda, rcar-host, vmd, xilinx,
xilinx-dma, xilinx-nwl from using pci_msi_create_irq_domain() to
using msi_create_parent_irq_domain() instead; this makes the
interrupt controller per-PCI device, allows dynamic allocation of
vectors after initialization, and allows support of IMS (Nam Cao)
APM X-Gene PCIe controller driver:
- Rewrite MSI handling to MSI CPU affinity, drop useless CPU hotplug
bits, use device-managed memory allocations, and clean things up
(Marc Zyngier)
- Probe xgene-msi as a standard platform driver rather than a
subsys_initcall (Marc Zyngier)
Broadcom STB PCIe controller driver:
- Add optional DT 'num-lanes' property and if present, use it to
override the Maximum Link Width advertised in Link Capabilities
(Jim Quinlan)
Cadence PCIe controller driver:
- Use PCIe Message routing types from the PCI core rather than
defining private ones (Hans Zhang)
Freescale i.MX6 PCIe controller driver:
- Add IMX8MQ_EP third 64-bit BAR in epc_features (Richard Zhu)
- Add IMX8MM_EP and IMX8MP_EP fixed 256-byte BAR 4 in epc_features
(Richard Zhu)
- Configure LUT for MSI/IOMMU in Endpoint mode so Root Complex can
trigger doorbel on Endpoint (Frank Li)
- Remove apps_reset (LTSSM_EN) from
imx_pcie_{assert,deassert}_core_reset(), which fixes a hotplug
regression on i.MX8MM (Richard Zhu)
- Delay Endpoint link start until configfs 'start' written (Richard
Zhu)
Intel VMD host bridge driver:
- Add Intel Panther Lake (PTL)-H/P/U Vendor ID (George D Sworo)
Qualcomm PCIe controller driver:
- Add DT binding and driver support for SA8255p, which supports ECAM
for Configuration Space access (Mayank Rana)
- Update DT binding and driver to describe PHYs and per-Root Port
resets in a Root Port stanza and deprecate describing them in the
host bridge; this makes it possible to support multiple Root Ports
in the future (Krishna Chaitanya Chundru)
- Add Qualcomm QCS615 to SM8150 DT binding (Ziyue Zhang)
- Add Qualcomm QCS8300 to SA8775p DT binding (Ziyue Zhang)
- Drop TBU and ref clocks from Qualcomm SM8150 and SC8180x DT
bindings (Konrad Dybcio)
- Document 'link_down' reset in Qualcomm SA8775P DT binding (Ziyue
Zhang)
- Add required PCIE_RESET_CONFIG_WAIT_MS delay after Link up IRQ
(Niklas Cassel)
Rockchip PCIe controller driver:
- Drop unused PCIe Message routing and code definitions (Hans Zhang)
- Remove several unused header includes (Hans Zhang)
- Use standard PCIe config register definitions instead of
rockchip-specific redefinitions (Geraldo Nascimento)
- Set Target Link Speed to 5.0 GT/s before retraining so we have a
chance to train at a higher speed (Geraldo Nascimento)
Rockchip DesignWare PCIe controller driver:
- Prevent race between link training and register update via DBI by
inhibiting link training after hot reset and link down (Wilfred
Mallawa)
- Add required PCIE_RESET_CONFIG_WAIT_MS delay after Link up IRQ
(Niklas Cassel)
Sophgo PCIe controller driver:
- Add DT binding and driver for Sophgo SG2044 PCIe controller driver
in Root Complex mode (Inochi Amaoto)
Synopsys DesignWare PCIe controller driver:
- Add required PCIE_RESET_CONFIG_WAIT_MS after waiting for Link up on
Ports that support > 5.0 GT/s. Slower Ports still rely on the
not-quite-correct PCIE_LINK_WAIT_SLEEP_MS 90ms default delay while
waiting for the Link (Niklas Cassel)"
* tag 'pci-v6.17-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (116 commits)
dt-bindings: PCI: qcom,pcie-sa8775p: Document 'link_down' reset
dt-bindings: PCI: Remove 83xx-512x-pci.txt
dt-bindings: PCI: Convert amazon,al-alpine-v[23]-pcie to DT schema
dt-bindings: PCI: Convert marvell,armada-3700-pcie to DT schema
dt-bindings: PCI: Convert apm,xgene-pcie to DT schema
dt-bindings: PCI: Convert axis,artpec6-pcie to DT schema
dt-bindings: PCI: Convert st,spear1340-pcie to DT schema
PCI: Move is_pciehp check out of pciehp_is_native()
PCI: pciehp: Use is_pciehp instead of is_hotplug_bridge
PCI/portdrv: Use is_pciehp instead of is_hotplug_bridge
PCI/ACPI: Fix runtime PM ref imbalance on Hot-Plug Capable ports
selftests: pci_endpoint: Add doorbell test case
misc: pci_endpoint_test: Add doorbell test case
PCI: endpoint: pci-epf-test: Add doorbell test support
PCI: endpoint: Add pci_epf_align_inbound_addr() helper for inbound address alignment
PCI: endpoint: pci-ep-msi: Add checks for MSI parent and mutability
PCI: endpoint: Add RC-to-EP doorbell support using platform MSI controller
PCI: dwc: Add Sophgo SG2044 PCIe controller driver in Root Complex mode
PCI: vmd: Switch to msi_create_parent_irq_domain()
PCI: vmd: Convert to lock guards
...
- Teach handle_simple_irq() to resend an in-progress interrupt (Marc
Zyngier)
- Defer probing if the MSI widget driver hasn't probed yet (Marc Zyngier)
- Drop useless conditional compilation, since pci-xgene.c is only compiled
when CONFIG_PCI_XGENE is selected (Marc Zyngier)
- Drop useless XGENE_PCIE_IP_VER_UNKN IP version (Marc Zyngier)
- Simplify and make per-CPU interrupt setup robust (Marc Zyngier)
- Drop superfluous struct xgene_msi fields (Marc Zyngier)
- Use device-managed memory allocations (Marc Zyngier)
- Drop intermediate xgene_msi_group tracking structure (Marc Zyngier)
- Rewrite pci-xgene-msi.c to fix MSI CPU affinity and clean things up (Marc
Zyngier)
- Resend an MSI racing with itself on a different CPU (Marc Zyngier)
- Probe xgene-msi as a standard platform driver rather than a
subsys_initcall (Marc Zyngier)
- Simplify MSI handler setup/teardown by dropping useless CPU hotplug bits
(Marc Zyngier)
- Remove unused cpuhp_state CPUHP_PCI_XGENE_DEAD (Marc Zyngier)
* pci/controller/xgene:
cpu/hotplug: Remove unused cpuhp_state CPUHP_PCI_XGENE_DEAD
PCI: xgene-msi: Restructure handler setup/teardown
PCI: xgene-msi: Probe as a standard platform driver
PCI: xgene-msi: Resend an MSI racing with itself on a different CPU
PCI: xgene-msi: Sanitise MSI allocation and affinity setting
PCI: xgene-msi: Get rid of intermediate tracking structure
PCI: xgene-msi: Use device-managed memory allocations
PCI: xgene-msi: Drop superfluous fields from xgene_msi structure
PCI: xgene-msi: Make per-CPU interrupt setup robust
PCI: xgene: Drop XGENE_PCIE_IP_VER_UNKN
PCI: xgene: Drop useless conditional compilation
PCI: xgene: Defer probing if the MSI widget driver hasn't probed yet
genirq: Teach handle_simple_irq() to resend an in-progress interrupt
- Fix log message that said "malformed TLP" when it should have said
"Unexpected Completion" (Hans Zhang)
- Fix log message that said "no fatal error" when it should have said "non
fatal error" (Hans Zhang)
- Remove several unused header includes (Hans Zhang)
* pci/controller/rockchip-host:
PCI: rockchip-host: Remove unused header includes
PCI: rockchip-host: Correct non-fatal error log message
PCI: rockchip-host: Fix "Unexpected Completion" log message
- Drop unused PCIe Message routing and code definitions (Hans Zhang)
- Use standard PCIe config register definitions instead of
rockchip-specific redefinitions (Geraldo Nascimento)
- Set Target Link Speed to 5.0 GT/s before retraining so we have a chance
to train at a higher speed (Geraldo Nascimento)
* pci/controller/rockchip:
PCI: rockchip: Set Target Link Speed to 5.0 GT/s before retraining
PCI: rockchip: Use standard PCIe definitions
PCI: rockchip: Remove redundant PCIe message routing definitions
- Export DWC MSI controller related APIs for use by upcoming DWC-based ECAM
implementation (Mayank Rana)
- Rename gen_pci_init() to pci_host_common_ecam_create() and export for use
by controller drivers (Mayank Rana)
- Add DT binding and driver support for SA8255p, which supports ECAM for
Configuration Space access (Mayank Rana)
- Update DT binding and driver to describe PHYs and per-Root Port resets in
a Root Port stanza and deprecate describing them in the host bridge; this
makes it possible to support multiple Root Ports in the future (Krishna
Chaitanya Chundru)
* pci/controller/qcom:
PCI: qcom: Add support for parsing the new Root Port binding
dt-bindings: PCI: qcom: Move PHY & reset GPIO to Root Port node
PCI: qcom: Add support for Qualcomm SA8255p based PCIe Root Complex
dt-bindings: PCI: qcom,pcie-sa8255p: Document ECAM compliant PCIe root complex
PCI: host-generic: Rename and export gen_pci_init() for PCIe controller drivers
PCI: dwc: Export DWC MSI controller related APIs
- Use devm_add_action_or_reset() when adding port->clk devm cleanup action
so we don't have to explicitly call clk_put() (Salah Triki)
* pci/controller/mvebu:
PCI: mvebu: Use devm_add_action_or_reset() instead of devm_add_action()
- Add IMX8MQ_EP third 64-bit BAR in epc_features (Richard Zhu)
- Add IMX8MM_EP and IMX8MP_EP fixed 256-byte BAR 4 in epc_features (Richard
Zhu)
- Factor imx_pcie_add_lut_by_rid() out of imx_pcie_enable_device() for use
by LUT configuration (Frank Li)
- Configure LUT for MSI/IOMMU in Endpoint mode so Root Complex can trigger
doorbel on Endpoint (Frank Li)
- Remove apps_reset (LTSSM_EN) from imx_pcie_{assert,deassert}_core_reset(),
which fixes a hotplug regression on i.MX8MM (Richard Zhu)
- Delay Endpoint link start until configfs 'start' written (Richard Zhu)
* pci/controller/imx6:
PCI: imx6: Delay link start until configfs 'start' written
PCI: imx6: Remove apps_reset toggling from imx_pcie_{assert/deassert}_core_reset
PCI: imx6: Add LUT configuration for MSI/IOMMU in Endpoint mode
PCI: imx6: Add helper function imx_pcie_add_lut_by_rid()
PCI: imx6: Add IMX8MM_EP and IMX8MP_EP fixed 256-byte BAR 4 in epc_features
PCI: imx6: Add IMX8MQ_EP third 64-bit BAR in epc_features
- Prevent race between link training and register update via DBI by
inhibiting link training after hot reset and link down (Wilfred Mallawa)
* pci/controller/dw-rockchip:
PCI: dw-rockchip: Delay link training after hot reset in EP mode
- Use PCIe Message routing types from the PCI core rather than defining
private ones (Hans Zhang)
* pci/controller/cadence:
PCI: cadence: Replace private message routing enums with PCI core definitions
- Add optional DT 'num-lanes' property and if present, use it to override
the Maximum Link Width advertised in Link Capabilities (Jim Quinlan)
* pci/controller/brcmstb:
PCI: brcmstb: Replace open coded value with PCIE_T_RRS_READY_MS
MAINTAINERS: Drop Nicolas from maintaining pcie-brcmstb
PCI: brcmstb: Set MLW based on "num-lanes" DT property if present
dt-bindings: PCI: brcm,stb-pcie: Add num-lanes property
- Rename PCIE_RESET_CONFIG_DEVICE_WAIT_MS to PCIE_RESET_CONFIG_WAIT_MS (the
required delay before sending config requests after a reset) (Niklas
Cassel)
- PCIE_T_RRS_READY_MS and PCIE_RESET_CONFIG_WAIT_MS were two names for the
same delay; replace PCIE_T_RRS_READY_MS with PCIE_RESET_CONFIG_WAIT_MS
and remove PCIE_T_RRS_READY_MS (Niklas Cassel)
- Add required PCIE_RESET_CONFIG_WAIT_MS delay after Link up IRQ to
dw-rockchip, qcom (Niklas Cassel)
- Add required PCIE_RESET_CONFIG_WAIT_MS after waiting for Link up on
Ports that support > 5.0 GT/s in dwc core (Niklas Cassel)
- Move LINK_WAIT_SLEEP_MS and LINK_WAIT_MAX_RETRIES to pci.h and prefix
with 'PCIE_' for potential sharing across drivers (Niklas Cassel)
* pci/controller/linkup-fix:
PCI: Move link up wait time and max retries macros to pci.h
PCI: dwc: Ensure that dw_pcie_wait_for_link() waits 100 ms after link up
PCI: qcom: Wait PCIE_RESET_CONFIG_WAIT_MS after link-up IRQ
PCI: dw-rockchip: Wait PCIE_RESET_CONFIG_WAIT_MS after link-up IRQ
PCI: rockchip-host: Use macro PCIE_RESET_CONFIG_WAIT_MS
PCI: Rename PCIE_RESET_CONFIG_DEVICE_WAIT_MS to PCIE_RESET_CONFIG_WAIT_MS
Add driver support for DesignWare based PCIe controller in SG2044 SoC. The
driver currently supports the Root Complex mode.
Signed-off-by: Inochi Amaoto <inochiama@gmail.com>
[mani: renamed the driver to 'pcie-sophgo.c' and Kconfig fix]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
[bhelgaas: whitespace]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20250504004420.202685-3-inochiama@gmail.com
Convert lock/unlock pairs to lock guard and tidy up the code.
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
[bhelgaas: rebase on dev_fwnode() conversion]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://patch.msgid.link/836cca37449c70922a2bea1fb13f37940a7a7132.1750858083.git.namcao@linutronix.de
Switch to msi_create_parent_irq_domain() from pci_msi_create_irq_domain()
which was using legacy MSI domain setup.
Signed-off-by: Nam Cao <namcao@linutronix.de>
[mani: reworded commit message]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
[bhelgaas: rebase on dev_fwnode() conversion, drop fwnode local var]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://patch.msgid.link/1279fe6500a1d8135d8f5feb2f055df008746c88.1750858083.git.namcao@linutronix.de
Switch to msi_create_parent_irq_domain() from pci_msi_create_irq_domain()
which was using legacy MSI domain setup.
Signed-off-by: Nam Cao <namcao@linutronix.de>
[mani: reworded commit message]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
[bhelgaas: rebase on dev_fwnode() conversion, drop fwnode local var]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://patch.msgid.link/b1353c797ce53714c22823de3bd2ae3d09fcd84f.1750858083.git.namcao@linutronix.de
Switch to msi_create_parent_irq_domain() from pci_msi_create_irq_domain()
which was using legacy MSI domain setup.
Signed-off-by: Nam Cao <namcao@linutronix.de>
[mani: reworded commit message]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
[bhelgaas: rebase on dev_fwnode() conversion, drop fwnode local var]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://patch.msgid.link/5ac6e216bf2eaa438c8854baf2ff3e5cf0b2284f.1750858083.git.namcao@linutronix.de
Switch to msi_create_parent_irq_domain() from pci_msi_create_irq_domain()
which was using legacy MSI domain setup.
Signed-off-by: Nam Cao <namcao@linutronix.de>
[mani: reworded commit message]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
[bhelgaas: rebase on dev_fwnode() conversion]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://patch.msgid.link/b4620dc1808f217a69d0ae50700ffa12ffd657eb.1750858083.git.namcao@linutronix.de
Switch to msi_create_parent_irq_domain() from pci_msi_create_irq_domain()
which was using legacy MSI domain setup.
Signed-off-by: Nam Cao <namcao@linutronix.de>
[mani: reworded commit message]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
[bhelgaas: rebase on dev_fwnode() conversion, drop fwnode local var]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://patch.msgid.link/ab4005db0a829549be1f348f6c27be50a2118b5e.1750858083.git.namcao@linutronix.de
Switch to msi_create_parent_irq_domain() from pci_msi_create_irq_domain()
which was using legacy MSI domain setup.
Signed-off-by: Nam Cao <namcao@linutronix.de>
[mani: reworded commit message]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
[bhelgaas: rebase on dev_fwnode() conversion, drop fwnode local var]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://patch.msgid.link/76f6e6ce6021607cd0fdfd79fef7d2eb69d9f361.1750858083.git.namcao@linutronix.de
Switch to msi_create_parent_irq_domain() from pci_msi_create_irq_domain()
which was using legacy MSI domain setup.
Signed-off-by: Nam Cao <namcao@linutronix.de>
[mani: reworded commit message & fixed merge conflict]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
[bhelgaas: rebase on dev_fwnode() conversion]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://patch.msgid.link/bfbd2e375269071b69e1aa85e629ee4b7c99518f.1750858083.git.namcao@linutronix.de
Switch to msi_create_parent_irq_domain() from pci_msi_create_irq_domain()
which was using legacy MSI domain setup.
Signed-off-by: Nam Cao <namcao@linutronix.de>
[mani: reworded commit message & squashed the kdoc cleanup patch]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
[bhelgaas: rebase on dev_fwnode() conversion]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/53946d74caf1fd134a1820eac82c3cf64d48779f.1750858083.git.namcao@linutronix.de
Switch to msi_create_parent_irq_domain() from pci_msi_create_irq_domain()
which was using legacy MSI domain setup.
Signed-off-by: Nam Cao <namcao@linutronix.de>
[mani: reworded commit message]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
[bhelgaas: rebase on dev_fwnode() conversion, drop fwnode local var]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/fa72703e06c2ee2c7554082c7152913eb0dd294f.1750858083.git.namcao@linutronix.de
Switch to msi_create_parent_irq_domain() from pci_msi_create_irq_domain()
which was using legacy MSI domain setup.
Signed-off-by: Nam Cao <namcao@linutronix.de>
[mani: reworded commit message]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
[bhelgaas: rebase on dev_fwnode() conversion]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://patch.msgid.link/0a88da04bb82bd588828a7889e9d58c515ea5dbb.1750858083.git.namcao@linutronix.de
Switch to msi_create_parent_irq_domain() from pci_msi_create_irq_domain()
which was using legacy MSI domain setup.
Signed-off-by: Nam Cao <namcao@linutronix.de>
[mani: reworded commit message]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
[bhelgaas: rebase on dev_fwnode() conversion]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://patch.msgid.link/68b2f9387bbe4f08bcd428bfab83ad1219fb8d80.1750858083.git.namcao@linutronix.de
Switch to msi_create_parent_irq_domain() from pci_msi_create_irq_domain()
which was using legacy MSI domain setup.
Signed-off-by: Nam Cao <namcao@linutronix.de>
[mani: reworded commit message]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
[bhelgaas: rebase on dev_fwnode() conversion, drop fwnode local var]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://patch.msgid.link/af46c15c47a7716f7e0c50d0f7391509c95b49c2.1750858083.git.namcao@linutronix.de
Switch to msi_create_parent_irq_domain() from pci_msi_create_irq_domain()
which was using legacy MSI domain setup.
Signed-off-by: Nam Cao <namcao@linutronix.de>
[mani: reworded commit message]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
[bhelgaas: rebase on dev_fwnode() conversion]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://patch.msgid.link/04d4a96046490e50139826c16423954e033cdf89.1750858083.git.namcao@linutronix.de
All irq_domain functions now accept fwnode instead of of_node. But many
PCI controllers still extract dev to of_node and then of_node to fwnode.
Instead, clean this up and simply use the dev_fwnode() helper to extract
fwnode directly from dev. Internally, it still does dev => of_node =>
fwnode steps, but it's now hidden from the users.
In the case of altera, this also removes an unused 'node' variable that is
only used when CONFIG_OF is enabled:
drivers/pci/controller/pcie-altera.c: In function 'altera_pcie_init_irq_domain':
drivers/pci/controller/pcie-altera.c:855:29: error: unused variable 'node' [-Werror=unused-variable]
855 | struct device_node *node = dev->of_node;
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de> # altera
[bhelgaas: squash together, rebase to precede msi-parent]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20250521163329.2137973-1-arnd@kernel.org
Link: https://patch.msgid.link/20250611104348.192092-16-jirislaby@kernel.org
Link: https://patch.msgid.link/20250723065907.1841758-1-jirislaby@kernel.org
According to Documentation/PCI/endpoint/pci-endpoint-cfs.rst, the Endpoint
controller (EPC) should only start the link when userspace writes '1' to
the '/sys/kernel/config/pci_ep/controllers/<EPC>/start' attribute, which
ultimately results in calling imx_pcie_start_link() via
pci_epc_start_store().
To align with the documented behavior, do not start the link automatically
when adding the EP controller.
Fixes: 75c2f26da0 ("PCI: imx6: Add i.MX PCIe EP mode support")
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
[mani: reworded commit subject and description]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250709033722.2924372-3-hongxing.zhu@nxp.com
apps_reset corresponds to LTSSM_EN in i.MX7, i.MX8MQ, i.MX8MM and i.MX8MP
platforms. Since assertion/de-assertion of apps_reset is done in
imx_pcie_ltssm_enable() and imx_pcie_ltssm_disable(), remove it from
imx_pcie_assert_core_reset() and imx_pcie_deassert_core_reset().
This also fixes a failure in enumerating the PI7C9X2G608GP (hotplug) chip
reliably on i.MX8MM, as reported by Tim.
It should be noted that only i.MX7D, i.MX8MQ, i.MX8MM, and i.MX8MP
platforms have the apps_reset logic, so this change doesn't have any effect
on other platforms.
Fixes: ef61c7d8d0 ("PCI: imx6: Deassert apps_reset in imx_pcie_deassert_core_reset()")
Reported-by: Tim Harvey <tharvey@gateworks.com>
Closes: https://lore.kernel.org/all/CAJ+vNU3ohR2YKTwC4xoYrc1z-neDoH2TTZcMHDy+poj9=jSy+w@mail.gmail.com/
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
[mani: reworded commit subject and description]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Tim Harvey <tharvey@gateworks.com> # imx8mp-venice-gw74xx (i.MX8MP + hotplug capable switch)
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250709033722.2924372-2-hongxing.zhu@nxp.com
Replace devm_add_action() with devm_add_action_or_reset() to avoid
explicitly dropping the 'port->clk' reference in error path.
Signed-off-by: Salah Triki <salah.triki@gmail.com>
[mani: reworded commit subject and description]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://patch.msgid.link/aHsgYALHfQbrgq0t@pc
Another utterly pointless aspect of the xgene-msi driver is that
it is built around CPU hotplug. Which is quite amusing since this
is one of the few arm64 platforms that, by construction, cannot
do CPU hotplug in a supported way (no EL3, no PSCI, no luck).
Drop the CPU hotplug nonsense and just setup the IRQs and handlers
in a less overdesigned way, grouping things more logically in the
process.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20250708173404.1278635-13-maz@kernel.org
Now that we have made the dependency between the PCI driver and
the MSI driver explicit, there is no need to use subsys_initcall()
as a probing hook, and we can rely on builtin_platform_driver()
instead.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20250708173404.1278635-12-maz@kernel.org
Since changing the affinity of an MSI really is about changing
the target address and that it isn't possible to mask an individual
MSI, it is completely possible for an interrupt to race with itself,
usually resulting in a lost interrupt.
Paper over the design blunder by informing the core code of this
sad state of affairs.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20250708173404.1278635-11-maz@kernel.org
Plugging a device that doesn't use managed affinity on an XGene-1
machine results in messages such as:
genirq: irq_chip PCI-MSIX-0000:01:00.0 did not update eff. affinity mask of irq 39
As it turns out, the driver was never updated to populate the effective
affinity on irq_set_affinity() call, and the core code is prickly about
that.
But upon further investigation, it appears that the driver keeps repainting
the hwirq field of the irq_data structure as a way to track the affinity
of the MSI, something that is very much frowned upon as it breaks the
fundamentals of an IRQ domain (an array indexed by hwirq).
Fixing this results more or less in a rewrite of the driver:
- Define how a hwirq and a CPU affinity map onto the MSI termination
registers
- Allocate a single entry in the bitmap per MSI instead of *8*
- Correctly track CPU affinity
- Fix the documentation so that it actually means something (to me)
- Use standard bitmap iterators
- and plenty of other cleanups
With this, the driver behaves correctly on my vintage Mustang board.
Signed-off-by: Marc Zyngier <maz@kernel.org>
[lpieralisi: replaced open coded GENMASK(6, 4) with MSInRx_HWIRQ_MASK]
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20250708173404.1278635-10-maz@kernel.org
The xgene-msi driver uses an odd construct in the form of an
intermediate tracking structure, evidently designed to deal with
multiple instances of the MSI widget. However, the existing HW
only has one set, and it is obvious that there won't be new HW
coming down that particular line.
Simplify the driver by using a bit of pointer arithmetic instead,
directly tracking the interrupt and avoiding extra memory allocation.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20250708173404.1278635-9-maz@kernel.org
Since the MSI driver is probed as a platform device, there is no
reason to not use device-managed allocations. That's including
the top-level bookkeeping structure, which is better dynamically
allocated than being static.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20250708173404.1278635-8-maz@kernel.org
The xgene_msi structure remembers both the of_node of the device
and the number of CPUs. All of which are perfectly useless.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20250708173404.1278635-7-maz@kernel.org
The way the per-CPU interrupts are dealt with in the XGene MSI
driver isn't great:
- the affinity is set after the interrupt is enabled
- nothing prevents userspace from moving the interrupt around
- the affinity setting code pointlessly allocates memory
- the driver checks for conditions that cannot possibly happen
Address all of this in one go, resulting in slightly simpler setup
code.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20250708173404.1278635-6-maz@kernel.org
XGENE_PCIE_IP_VER_UNKN is only refered to when probing for the
original XGene PCIe implementation, and get immediately overridden
if the device has the "apm,xgene-pcie" compatible string.
Given that the only way to get there is by finding this very string in
the DT, it is obvious that we will always overwrite the version with
XGENE_PCIE_IP_VER_1.
Drop the whole thing.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20250708173404.1278635-5-maz@kernel.org
pci-xgene.c only gets compiled if CONFIG_PCI_XGENE is selected.
It is therefore pointless to check for CONFIG_PCI_XGENE inside
the driver.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20250708173404.1278635-4-maz@kernel.org
As a preparatory work to make the XGene MSI driver probe less of
a sorry hack, make the PCI driver check for the availability of
the MSI parent domain, and defer the probing otherwise.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20250708173404.1278635-3-maz@kernel.org
Add LUT entry for MSI/IOMMU in Endpoint mode by calling
imx_pcie_add_lut_by_rid() helper function. Since only one physical function
is supported in the Endpoint mode for now, '0' is passed as the Device ID.
This sets up a single LUT entry required for MSI/IOMMU.
The Endpoint function can operate without LUT configuration if neither
IOMMU nor MSI is used by the platform. This LUT configuration is used for
the EP doorbell feature by allowing the Root Complex to trigger the
doorbell on the Endpoint with the help of the Endpoint MSI controller.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
[mani: reworded the comments & commit message and dropped tested-by tag]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://patch.msgid.link/20250710-ep-msi-v21-2-57683fc7fb25@nxp.com
Add helper function imx_pcie_add_lut_by_rid(), which will be used by the
upcoming LUT configuration for MSI/IOMMU in the Endpoint mode. No
functional change.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
[mani: reworded commit message and dropped tested-by tag]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://patch.msgid.link/20250710-ep-msi-v21-1-57683fc7fb25@nxp.com
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEIbPD0id6easf0xsudhRwX5BBoF4FAmh6uxMTHHdlaS5saXVA
a2VybmVsLm9yZwAKCRB2FHBfkEGgXsDqB/9EZrNSmMhoctjhBwrEjilRPaBHaD0f
7AGbdvs78sZDC2FMQeeqVeUDgv7nhZoT9B/cjSNkAXF8LdtEXOpiYY0sqG+fO8c9
2DHBLBBGbFg+/SI+2SLzgrg8ixplnEF2HPR3pIgpmvqOKJcBd6+LnlyXs3xuBhc/
XCerEwjHDpC27YQf3ZFvgomH1rw4w0yENZaz/ztpca41GScmbBq6K9c0SAzherBJ
IDcbSUHNkT9LoFdXG9gawwX++XrBsfsKwlfAX6lYuzj+rdY5uxJaqMBg5sIA5Huh
aRLB9gXHQVABTqp73kG76ZtBdmMsd2S1JF0YdRxdsL91MQ1C0n7AW9iK
=0Qh6
-----END PGP SIGNATURE-----
Merge tag 'hyperv-fixes-signed-20250718' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull hyperv fixes from Wei Liu:
- Select use CONFIG_SYSFB only if EFI is enabled (Michael Kelley)
- An assorted set of fixes to remove warnings for missing export.h
header inclusion (Naman Jain)
- An assorted set of fixes for when Linux run as the root partition
for Microsoft Hypervisor (Mukesh Rathor, Nuno Das Neves, Stanislav
Kinsburskii)
- Fix the check for HYPERVISOR_CALLBACK_VECTOR (Naman Jain)
- Fix fcopy tool to handle irregularities with size of ring buffer
(Naman Jain)
- Fix incorrect file path conversion in fcopy tool (Yasumasa Suenaga)
* tag 'hyperv-fixes-signed-20250718' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
tools/hv: fcopy: Fix irregularities with size of ring buffer
PCI: hv: Use the correct hypercall for unmasking interrupts on nested
x86/hyperv: Expose hv_map_msi_interrupt()
Drivers: hv: Use nested hypercall for post message and signal event
x86/hyperv: Clean up hv_map/unmap_interrupt() return values
x86/hyperv: Fix usage of cpu_online_mask to get valid cpu
PCI: hv: Don't load the driver for baremetal root partition
net: mana: Fix warnings for missing export.h header inclusion
PCI: hv: Fix warnings for missing export.h header inclusion
clocksource: hyper-v: Fix warnings for missing export.h header inclusion
x86/hyperv: Fix warnings for missing export.h header inclusion
Drivers: hv: Fix warnings for missing export.h header inclusion
Drivers: hv: Fix the check for HYPERVISOR_CALLBACK_VECTOR
tools/hv: fcopy: Fix incorrect file path conversion
Drivers: hv: Select CONFIG_SYSFB only if EFI is enabled
The delay that we are waiting on in brcm_pcie_start_link() is
PCIE_T_RRS_READY_MS, use it.
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
[mani: Removed the redundant comment]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://patch.msgid.link/20250624231923.990361-3-florian.fainelli@broadcom.com
The DT binding has moved the PHY, PERST# properties to Root Port node from
the Host Bridge node. So add support for parsing the new binding. The new
binding uses 'reset-gpios' property for PERST#, hence parse the same
property in the driver instead of the legacy 'perst-gpios'.
To maintain DT backwards compatibility, fallback to the legacy method of
parsing the host bridge node if the properties are not present in the Root
Port node.
Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
[mani: refactored the root port parsing code, fixed a bug & commit message rewording]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20250702-perst-v5-2-920b3d1f6ee1@qti.qualcomm.com
For IMX8MM_EP and IMX8MP_EP, add fixed 256-byte BAR 4 and reserved BAR 5
in imx8m_pcie_epc_features.
Fixes: 75c2f26da0 ("PCI: imx6: Add i.MX PCIe EP mode support")
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
[bhelgaas: add details in subject]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250708091003.2582846-3-hongxing.zhu@nxp.com
Running as nested root on MSHV imposes a different requirement
for the pci-hyperv controller.
In this setup, the interrupt will first come to the L1 (nested) hypervisor,
which will deliver it to the appropriate root CPU. Instead of issuing the
RETARGET hypercall, issue the MAP_DEVICE_INTERRUPT hypercall to L1 to
complete the setup.
Rename hv_arch_irq_unmask() to hv_irq_retarget_interrupt().
Co-developed-by: Jinank Jain <jinankjain@linux.microsoft.com>
Signed-off-by: Jinank Jain <jinankjain@linux.microsoft.com>
Signed-off-by: Stanislav Kinsburskii <skinsburskii@linux.microsoft.com>
Signed-off-by: Nuno Das Neves <nunodasneves@linux.microsoft.com>
Reviewed-by: Roman Kisel <romank@linux.microsoft.com>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/1752261532-7225-4-git-send-email-nunodasneves@linux.microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Message-ID: <1752261532-7225-4-git-send-email-nunodasneves@linux.microsoft.com>
Move away from the legacy MSI domain setup, switch to use
msi_create_parent_irq_domain().
While doing the conversion, I noticed that hv_compose_msi_msg() is doing
more than it is supposed to (composing message). This function also
allocates and populates struct tran_int_desc, which should be done in
hv_pcie_domain_alloc() instead. It works, but it is not the correct design.
However, I have no hardware to test such change, therefore I leave a TODO
note.
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Nam Cao <namcao@linutronix.de>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Tested-by: Michael Kelley <mhklinux@outlook.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The root partition only uses VMBus when running nested.
When running on baremetal the Hyper-V PCI driver is not needed,
so do not initialize it.
Signed-off-by: Mukesh Rathor <mrathor@linux.microsoft.com>
Signed-off-by: Nuno Das Neves <nunodasneves@linux.microsoft.com>
Reviewed-by: Roman Kisel <romank@linux.microsoft.com>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/1751582677-30930-2-git-send-email-nunodasneves@linux.microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Message-ID: <1751582677-30930-2-git-send-email-nunodasneves@linux.microsoft.com>
Fix below warning in Hyper-V PCI driver that comes when kernel is
compiled with W=1 option. Include export.h in driver files to fix it.
* warning: EXPORT_SYMBOL() is used, but #include <linux/export.h>
is missing
Signed-off-by: Naman Jain <namjain@linux.microsoft.com>
Reviewed-by: Saurabh Sengar <ssengar@linux.microsoft.com>
Link: https://lore.kernel.org/r/20250611100459.92900-6-namjain@linux.microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Message-ID: <20250611100459.92900-6-namjain@linux.microsoft.com>
Rockchip controllers can support up to 5.0 GT/s link speed. But the driver
doesn't set the Target Link Speed currently. This may cause failure in
retraining the link to 5.0 GT/s if supported by the endpoint. So set the
Target Link Speed to 5.0 GT/s in the Link Control and Status Register 2.
Fixes: e77f847df5 ("PCI: rockchip: Add Rockchip PCIe controller support")
Signed-off-by: Geraldo Nascimento <geraldogabriel@gmail.com>
[mani: fixed whitespace warning, commit message rewording, added fixes tag]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Robin Murphy <robin.murphy@arm.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/0afa6bc47b7f50e2e81b0b47d51c66feb0fb565f.1751322015.git.geraldogabriel@gmail.com
Current code uses custom-defined register offsets and bitfields for the
standard PCIe registers. This creates duplication as the PCI header already
defines them. So, switch to using the standard PCIe definitions and drop
the custom ones.
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Geraldo Nascimento <geraldogabriel@gmail.com>
[mani: commit message rewording]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
[bhelgaas: include bitfield.h]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/e81700ef4b49f584bc8834bfb07b6d8995fc1f42.1751322015.git.geraldogabriel@gmail.com
Rename gen_pci_init() API as pci_host_common_ecam_create() and export it to
allow the PCIe controller drivers to create and configure the ECAM region.
Note that this API should only used by the drivers managing the drvdata on
their own. Rest should continue using pci_host_common_init() API.
Signed-off-by: Mayank Rana <mayank.rana@oss.qualcomm.com>
[mani: commit message rewording]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://patch.msgid.link/20250616224259.3549811-3-mayank.rana@oss.qualcomm.com
Export dw_pcie_msi_host_init(), dw_pcie_msi_init(), and dw_pcie_free_msi()
APIs to allow them to be reused by the upcoming DWC based ECAM driver
implementation. Also, move MSI IRQ related initialization code to
dw_pcie_msi_init(), as this code must be executed before dw_pcie_msi_init()
API can be used with ECAM driver.
Signed-off-by: Mayank Rana <mayank.rana@oss.qualcomm.com>
[mani: commit message rewording]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://patch.msgid.link/20250616224259.3549811-2-mayank.rana@oss.qualcomm.com
The apple driver relies on being able to directly find the matching root
port structure from the platform device that represents this port.
A previous hack stashed a pointer to the root port structure in the config
window private pointer, but that ended up relying on assumptions that break
other drivers.
Instead, bite the bullet and track the association as part of the driver
itself as a list of probed root ports.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20250625111806.4153773-3-maz@kernel.org
Move the LINK_WAIT_SLEEP_MS and LINK_WAIT_MAX_RETRIES macros to pci.h.
Prefix the macros with PCIE_ in order to avoid redefining these for
drivers that already have macros named like this.
No functional changes.
Suggested-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://patch.msgid.link/20250625102347.1205584-15-cassel@kernel.org
As per PCIe r6.0, sec 6.6.1, a Downstream Port that supports Link speeds
greater than 5.0 GT/s, software must wait a minimum of 100 ms after Link
training completes before sending a Configuration Request.
Add this delay in dw_pcie_wait_for_link(), after the link is reported as
up. The delay will only be performed in the success case where the link
came up.
DWC glue drivers that have a link up IRQ (drivers that set
use_linkup_irq = true) do not call dw_pcie_wait_for_link(), instead they
perform this delay in their threaded link up IRQ handler.
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Link: https://patch.msgid.link/20250625102347.1205584-14-cassel@kernel.org
Per PCIe r6.0, sec 6.6.1, software must generally wait a minimum of
100ms (PCIE_RESET_CONFIG_WAIT_MS) after Link training completes before
sending a Configuration Request.
Prior to 36971d6c5a ("PCI: qcom: Don't wait for link if we can detect
Link Up"), qcom used dw_pcie_wait_for_link(), which waited between 0
and 90ms after the link came up before we enumerate the bus, and this
was apparently enough for most devices.
After 36971d6c5a, qcom_pcie_global_irq_thread() started enumeration
immediately when handling the link-up IRQ, and devices (e.g., Laszlo
Fiat's PLEXTOR PX-256M8PeGN NVMe SSD) may not be ready to handle config
requests yet.
Delay PCIE_RESET_CONFIG_WAIT_MS after the link-up IRQ before starting
enumeration.
Fixes: 82a823833f ("PCI: qcom: Add Qualcomm PCIe controller driver")
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Link: https://patch.msgid.link/20250625102347.1205584-13-cassel@kernel.org
Per PCIe r6.0, sec 6.6.1, software must generally wait a minimum of
100ms (PCIE_RESET_CONFIG_WAIT_MS) after Link training completes before
sending a Configuration Request.
Prior to ec9fd499b9 ("PCI: dw-rockchip: Don't wait for link since
we can detect Link Up"), dw-rockchip used dw_pcie_wait_for_link(),
which waited between 0 and 90ms after the link came up before we
enumerate the bus, and this was apparently enough for most devices.
After ec9fd499b9, rockchip_pcie_rc_sys_irq_thread() started
enumeration immediately when handling the link-up IRQ, and devices
(e.g., Laszlo Fiat's PLEXTOR PX-256M8PeGN NVMe SSD) may not be ready
to handle config requests yet.
Delay PCIE_RESET_CONFIG_WAIT_MS after the link-up IRQ before starting
enumeration.
Fixes: 0e898eb8df ("PCI: rockchip-dwc: Add Rockchip RK356X host controller driver")
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Cc: Laszlo Fiat <laszlo.fiat@proton.me>
Link: https://patch.msgid.link/20250625102347.1205584-12-cassel@kernel.org
Macro PCIE_RESET_CONFIG_DEVICE_WAIT_MS was added to pci.h in commit
d5ceb9496c ("PCI: Add PCIE_RESET_CONFIG_DEVICE_WAIT_MS waiting time
value").
Later, in commit 70a7bfb1e5 ("PCI: rockchip-host: Wait 100ms after reset
before starting configuration"), PCIE_T_RRS_READY_MS was added to pci.h.
These macros are duplicates, and represent the exact same delay in the
PCIe specification.
Since the comment above PCIE_RESET_CONFIG_WAIT_MS is strictly more correct
than the comment above PCIE_T_RRS_READY_MS, change rockchip-host to use
PCIE_RESET_CONFIG_WAIT_MS, and remove PCIE_T_RRS_READY_MS, as
rockchip-host is the only user of this macro.
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Link: https://patch.msgid.link/20250625102347.1205584-11-cassel@kernel.org
By default, the driver relies on the default hardware defined value for the
Max Link Width (MLW) capability. But if the "num-lanes" DT property is
present, assume that the chip's default capability information is incorrect
or undesired, and use the specified value instead.
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
[mani: reworded the description and comments]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250530224035.41886-3-james.quinlan@broadcom.com
RK3588 TRM, section "11.6.1.3.3 Hot Reset and Link-Down Reset" states that:
If you want to delay link re-establishment (after reset) so that you can
reprogram some registers through DBI, you must set app_ltssm_enable =0
immediately after core_rst_n as shown in above. This can be achieved by
enable the app_dly2_en, and end-up the delay by assert app_dly2_done.
I.e. setting app_dly2_en will automatically deassert app_ltssm_enable on
a hot reset, and setting app_dly2_done will re-assert app_ltssm_enable,
re-enabling link training.
When receiving a hot reset/link-down IRQ when running in EP mode, we will
call dw_pcie_ep_linkdown(), which may update registers through DBI. Unless
link training is inhibited, these register updates race with the link
training.
To avoid the race, set PCIE_LTSSM_APP_DLY2_EN so the controller never
automatically trains the link after a link-down or hot reset interrupt.
That way any DBI updates done in the dw_pcie_ep_linkdown() path will happen
while the link is still down. Then allow link training by setting
PCIE_LTSSM_APP_DLY2_DONE
Co-developed-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20250613101908.2182053-2-cassel@kernel.org
The Rockchip driver contains duplicated message routing and INTx code
definitions (e.g., ROCKCHIP_PCIE_MSG_ROUTING_TO_RC,
ROCKCHIP_PCIE_MSG_CODE_ASSERT_INTA). These are already provided by the
PCI core in drivers/pci/pci.h as PCIE_MSG_TYPE_R_RC and
PCIE_MSG_CODE_ASSERT_INTA, respectively.
Remove the driver-specific definitions in favor of the core definitions
instead. This aligns the driver with the PCIe specification and reduces
maintenance overhead.
Signed-off-by: Hans Zhang <18255117159@163.com>
[mani: commit message rewording]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://patch.msgid.link/20250607154913.805027-3-18255117159@163.com
The Cadence driver previously defined its own message routing enums (e.g.,
MSG_ROUTING_LOCAL) and message codes, which duplicated existing PCI core
macros (PCIE_MSG_TYPE_R_LOCAL, PCIE_MSG_CODE_ASSERT_INTA, etc.) in
drivers/pci/pci.h. These core definitions align with the PCIe r6.0 spec.
Remove the driver-specific enums and switch to the centralized PCI core
macros. This eliminates redundancy, ensures consistency, and simplifies
future updates. No functional changes are introduced.
Signed-off-by: Hans Zhang <18255117159@163.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://patch.msgid.link/20250607154913.805027-2-18255117159@163.com
Allow dynamic MSI-X vector allocation for pci_hyperv PCI controller
by adding support for the flag MSI_FLAG_PCI_MSIX_ALLOC_DYN and using
pci_msix_prepare_desc() to prepare the MSI-X descriptors.
Feature support added for both x86 and ARM64
Signed-off-by: Shradha Gupta <shradhagupta@linux.microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Saurabh Sengar <ssengar@linux.microsoft.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Clean up the driver by removing unnecessary header includes that are no
longer referenced after the recent refactoring.
Signed-off-by: Hans Zhang <18255117159@163.com>
[mani: commit message rewording]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://patch.msgid.link/20250607160201.807043-4-18255117159@163.com
Correct the debug message for PCIE_CLIENT_INT_NFATAL_ERR from
"no fatal error" to "non fatal error interrupt received" to match the
actual interrupt semantics. This avoids confusion in log interpretation.
Signed-off-by: Hans Zhang <18255117159@163.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://patch.msgid.link/20250607160201.807043-3-18255117159@163.com
-----BEGIN PGP SIGNATURE-----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=eWJw
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Print the actual delay time in pci_bridge_wait_for_secondary_bus()
instead of assuming it was 1000ms (Wilfred Mallawa)
- Revert 'iommu/amd: Prevent binding other PCI drivers to IOMMU PCI
devices', which broke resume from system sleep on AMD platforms and
has been fixed by other commits (Lukas Wunner)
Resource management:
- Remove mtip32xx use of pcim_iounmap_regions(), which is deprecated
and unnecessary (Philipp Stanner)
- Remove pcim_iounmap_regions() and pcim_request_region_exclusive()
and related flags since all uses have been removed (Philipp
Stanner)
- Rework devres 'request' functions so they are no longer 'hybrid',
i.e., their behavior no longer depends on whether
pcim_enable_device or pci_enable_device() was used, and remove
related code (Philipp Stanner)
- Warn (not BUG()) about failure to assign optional resources (Ilpo
Järvinen)
Error handling:
- Log the DPC Error Source ID only when it's actually valid (when
ERR_FATAL or ERR_NONFATAL was received from a downstream device)
and decode into bus/device/function (Bjorn Helgaas)
- Determine AER log level once and save it so all related messages
use the same level (Karolina Stolarek)
- Use KERN_WARNING, not KERN_ERR, when logging PCIe Correctable
Errors (Karolina Stolarek)
- Ratelimit PCIe Correctable and Non-Fatal error logging, with sysfs
controls on interval and burst count, to avoid flooding logs and
RCU stall warnings (Jon Pan-Doh)
Power management:
- Increment PM usage counter when probing reset methods so we don't
try to read config space of a powered-off device (Alex Williamson)
- Set all devices to D0 during enumeration to ensure ACPI opregion is
connected via _REG (Mario Limonciello)
Power control:
- Rename pwrctrl Kconfig symbols from 'PWRCTL' to 'PWRCTRL' to match
the filename paths. Retain old deprecated symbols for
compatibility, except for the pwrctrl slot driver
(PCI_PWRCTRL_SLOT) (Johan Hovold)
- When unregistering pwrctrl, cancel outstanding rescan work before
cleaning up data structures to avoid use-after-free issues (Brian
Norris)
Bandwidth control:
- Simplify link bandwidth controller by replacing the count of Link
Bandwidth Management Status (LBMS) events with a PCI_LINK_LBMS_SEEN
flag (Ilpo Järvinen)
- Update the Link Speed after retraining, since the Link Speed may
have changed (Ilpo Järvinen)
PCIe native device hotplug:
- Ignore Presence Detect Changed caused by DPC.
pciehp already ignores Link Down/Up events caused by DPC, but on
slots using in-band presence detect, DPC causes a spurious Presence
Detect Changed event (Lukas Wunner)
- Ignore Link Down/Up caused by Secondary Bus Reset.
On hotplug ports using in-band presence detect, the reset causes a
Presence Detect Changed event, which mistakenly caused teardown and
re-enumeration of the device. Drivers may need to annotate code
that resets their device (Lukas Wunner)
Virtualization:
- Add an ACS quirk for Loongson Root Ports that don't advertise ACS
but don't allow peer-to-peer transactions between Root Ports; the
quirk allows each Root Port to be in a separate IOMMU group (Huacai
Chen)
Endpoint framework:
- For fixed-size BARs, retain both the actual size and the possibly
larger size allocated to accommodate iATU alignment requirements
(Jerome Brunet)
- Simplify ctrl/SPAD space allocation and avoid allocating more space
than needed (Jerome Brunet)
- Correct MSI-X PBA offset calculations for DesignWare and Cadence
endpoint controllers (Niklas Cassel)
- Align the return value (number of interrupts) encoding for
pci_epc_get_msi()/pci_epc_ops::get_msi() and
pci_epc_get_msix()/pci_epc_ops::get_msix() (Niklas Cassel)
- Align the nr_irqs parameter encoding for
pci_epc_set_msi()/pci_epc_ops::set_msi() and
pci_epc_set_msix()/pci_epc_ops::set_msix() (Niklas Cassel)
Common host controller library:
- Convert pci-host-common to a library so platforms that don't need
native host controller drivers don't need to include these helper
functions (Manivannan Sadhasivam)
Apple PCIe controller driver:
- Extract ECAM bridge creation helper from pci_host_common_probe() to
separate driver-specific things like MSI from PCI things (Marc
Zyngier)
- Dynamically allocate RID-to_SID bitmap to prepare for SoCs with
varying capabilities (Marc Zyngier)
- Skip ports disabled in DT when setting up ports (Janne Grunau)
- Add t6020 compatible string (Alyssa Rosenzweig)
- Add T602x PCIe support (Hector Martin)
- Directly set/clear INTx mask bits because T602x dropped the
accessors that could do this without locking (Marc Zyngier)
- Move port PHY registers to their own reg items to accommodate
T602x, which moves them around; retain default offsets for existing
DTs that lack phy%d entries with the reg offsets (Hector Martin)
- Stop polling for core refclk, which doesn't work on T602x and the
bootloader has already done anyway (Hector Martin)
- Use gpiod_set_value_cansleep() when asserting PERST# in probe
because we're allowed to sleep there (Hector Martin)
Cadence PCIe controller driver:
- Drop a runtime PM 'put' to resolve a runtime atomic count underflow
(Hans Zhang)
- Make the cadence core buildable as a module (Kishon Vijay Abraham I)
- Add cdns_pcie_host_disable() and cdns_pcie_ep_disable() for use by
loadable drivers when they are removed (Siddharth Vadapalli)
Freescale i.MX6 PCIe controller driver:
- Apply link training workaround only on IMX6Q, IMX6SX, IMX6SP
(Richard Zhu)
- Remove redundant dw_pcie_wait_for_link() from
imx_pcie_start_link(); since the DWC core does this, imx6 only
needs it when retraining for a faster link speed (Richard Zhu)
- Toggle i.MX95 core reset to align with PHY powerup (Richard Zhu)
- Set SYS_AUX_PWR_DET to work around i.MX95 ERR051624 erratum: in
some cases, the controller can't exit 'L23 Ready' through Beacon or
PERST# deassertion (Richard Zhu)
- Clear GEN3_ZRXDC_NONCOMPL to work around i.MX95 ERR051586 erratum:
controller can't meet 2.5 GT/s ZRX-DC timing when operating at 8
GT/s, causing timeouts in L1 (Richard Zhu)
- Wait for i.MX95 PLL lock before enabling controller (Richard Zhu)
- Save/restore i.MX95 LUT for suspend/resume (Richard Zhu)
Mobiveil PCIe controller driver:
- Return bool (not int) for link-up check in
mobiveil_pab_ops.link_up() and layerscape-gen4, mobiveil (Hans
Zhang)
NVIDIA Tegra194 PCIe controller driver:
- Create debugfs directory for 'aspm_state_cnt' only when
CONFIG_PCIEASPM is enabled, since there are no other entries (Hans
Zhang)
Qualcomm PCIe controller driver:
- Add OF support for parsing DT 'eq-presets-<N>gts' property for lane
equalization presets (Krishna Chaitanya Chundru)
- Read Maximum Link Width from the Link Capabilities register if DT
lacks 'num-lanes' property (Krishna Chaitanya Chundru)
- Add Physical Layer 64 GT/s Capability ID and register offsets for
8, 32, and 64 GT/s lane equalization registers (Krishna Chaitanya
Chundru)
- Add generic dwc support for configuring lane equalization presets
(Krishna Chaitanya Chundru)
- Add DT and driver support for PCIe on IPQ5018 SoC (Nitheesh Sekar)
Renesas R-Car PCIe controller driver:
- Describe endpoint BAR 4 as being fixed size (Jerome Brunet)
- Document how to obtain R-Car V4H (r8a779g0) controller firmware
(Yoshihiro Shimoda)
Rockchip PCIe controller driver:
- Reorder rockchip_pci_core_rsts because
reset_control_bulk_deassert() deasserts in reverse order, to fix a
link training regression (Jensen Huang)
- Mark RK3399 as being capable of raising INTx interrupts (Niklas
Cassel)
Rockchip DesignWare PCIe controller driver:
- Check only PCIE_LINKUP, not LTSSM status, to determine whether the
link is up (Shawn Lin)
- Increase N_FTS (used in L0s->L0 transitions) and enable ASPM L0s
for Root Complex and Endpoint modes (Shawn Lin)
- Hide the broken ATS Capability in rockchip_pcie_ep_init() instead
of rockchip_pcie_ep_pre_init() so it stays hidden after PERST#
resets non-sticky registers (Shawn Lin)
- Call phy_power_off() before phy_exit() in rockchip_pcie_phy_deinit()
(Diederik de Haas)
Synopsys DesignWare PCIe controller driver:
- Set PORT_LOGIC_LINK_WIDTH to one lane to make initial link training
more robust; this will not affect the intended link width if all
lanes are functional (Wenbin Yao)
- Return bool (not int) for link-up check in dw_pcie_ops.link_up()
and armada8k, dra7xx, dw-rockchip, exynos, histb, keembay,
keystone, kirin, meson, qcom, qcom-ep, rcar_gen4, spear13xx,
tegra194, uniphier, visconti (Hans Zhang)
- Add debugfs support for exposing DWC device-specific PTM context
(Manivannan Sadhasivam)
TI J721E PCIe driver:
- Make j721e buildable as a loadable and removable module (Siddharth
Vadapalli)
- Fix j721e host/endpoint dependencies that result in link failures
in some configs (Arnd Bergmann)
Device tree bindings:
- Add qcom DT binding for 'global' interrupt (PCIe controller and
link-specific events) for ipq8074, ipq8074-gen3, ipq6018, sa8775p,
sc7280, sc8180x sdm845, sm8150, sm8250, sm8350 (Manivannan
Sadhasivam)
- Add qcom DT binding for 8 MSI SPI interrupts for msm8998, ipq8074,
ipq8074-gen3, ipq6018 (Manivannan Sadhasivam)
- Add dw rockchip DT binding for rk3576 and rk3562 (Kever Yang)
- Correct indentation and style of examples in brcm,stb-pcie,
cdns,cdns-pcie-ep, intel,keembay-pcie-ep, intel,keembay-pcie,
microchip,pcie-host, rcar-pci-ep, rcar-pci-host, xilinx-versal-cpm
(Krzysztof Kozlowski)
- Convert Marvell EBU (dove, kirkwood, armada-370, armada-xp) and
armada8k from text to schema DT bindings (Rob Herring)
- Remove obsolete .txt DT bindings for content that has been moved to
schemas (Rob Herring)
- Add qcom DT binding for MHI registers in IPQ5332, IPQ6018, IPQ8074
and IPQ9574 (Varadarajan Narayanan)
- Convert v3,v360epc-pci from text to DT schema binding (Rob Herring)
- Change microchip,pcie-host DT binding to be 'dma-noncoherent' since
PolarFire may be configured that way (Conor Dooley)
Miscellaneous:
- Drop 'pci' suffix from intel_mid_pci.c filename to match similar
files (Andy Shevchenko)
- All platforms with PCI have an MMU, so add PCI Kconfig dependency
on MMU to simplify build testing and avoid inadvertent build
regressions (Arnd Bergmann)
- Update Krzysztof Wilczyński's email address in MAINTAINERS
(Krzysztof Wilczyński)
- Update Manivannan Sadhasivam's email address in MAINTAINERS
(Manivannan Sadhasivam)"
* tag 'pci-v6.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (147 commits)
MAINTAINERS: Update Manivannan Sadhasivam email address
PCI: j721e: Fix host/endpoint dependencies
PCI: j721e: Add support to build as a loadable module
PCI: cadence-ep: Introduce cdns_pcie_ep_disable() helper for cleanup
PCI: cadence-host: Introduce cdns_pcie_host_disable() helper for cleanup
PCI: cadence: Add support to build pcie-cadence library as a kernel module
MAINTAINERS: Update Krzysztof Wilczyński email address
PCI: Remove unnecessary linesplit in __pci_setup_bridge()
PCI: WARN (not BUG()) when we fail to assign optional resources
PCI: Remove unused pci_printk()
PCI: qcom: Replace PERST# sleep time with proper macro
PCI: dw-rockchip: Replace PERST# sleep time with proper macro
PCI: host-common: Convert to library for host controller drivers
PCI/ERR: Remove misleading TODO regarding kernel panic
PCI: cadence: Remove duplicate message code definitions
PCI: endpoint: Align pci_epc_set_msix(), pci_epc_ops::set_msix() nr_irqs encoding
PCI: endpoint: Align pci_epc_set_msi(), pci_epc_ops::set_msi() nr_irqs encoding
PCI: endpoint: Align pci_epc_get_msix(), pci_epc_ops::get_msix() return value encoding
PCI: endpoint: Align pci_epc_get_msi(), pci_epc_ops::get_msi() return value encoding
PCI: cadence-ep: Correct PBA offset in .set_msix() callback
...
- Create debugfs directory for 'aspm_state_cnt' only when CONFIG_PCIEASPM
is enabled, since there are no other entries (Hans Zhang)
* pci/controller/tegra194:
PCI: tegra194: Create debugfs directory only when CONFIG_PCIEASPM is enabled
- Reorder rockchip_pci_core_rsts because reset_control_bulk_deassert()
deasserts in reverse order, to fix a link training regression (Jensen
Huang)
- Mark RK3399 as being capable of raising INTx interrupts (Niklas Cassel)
* pci/controller/rockchip:
PCI: rockchip-ep: Mark RK3399 as intx_capable
PCI: rockchip: Fix order of rockchip_pci_core_rsts
- Describe endpoint BAR 4 as being fixed size (Jerome Brunet)
- Document how to obtain R-Car V4H (r8a779g0) controller firmware
(Yoshihiro Shimoda)
* pci/controller/rcar-gen4:
PCI: rcar-gen4: Document how to obtain platform firmware
PCI: rcar-gen4: set ep BAR4 fixed size
- Add OF support for parsing DT 'eq-presets-<N>gts' property for lane
equalization presets (Krishna Chaitanya Chundru)
- Read Maximum Link Width from the Link Capabilities register if DT lacks
'num-lanes' property (Krishna Chaitanya Chundru)
- Add Physical Layer 64 GT/s Capability ID and register offsets for 8, 32,
and 64 GT/s lane equalization registers (Krishna Chaitanya Chundru)
- Add generic dwc support for configuring lane equalization presets
(Krishna Chaitanya Chundru)
- Add DT and driver support for PCIe on IPQ5018 SoC (Nitheesh Sekar)
* pci/controller/qcom:
PCI: qcom: Add support for IPQ5018
dt-bindings: PCI: qcom: Add IPQ5018 SoC
PCI: dwc: Add support for configuring lane equalization presets
PCI: Add lane equalization register offsets
PCI: dwc: Update pci->num_lanes to maximum supported link width
PCI: of: Add of_pci_get_equalization_presets() API
- Use for_each_of_range() iterator for parsing 'ranges' (Rob Herring)
* pci/controller/mvebu:
PCI: mvebu: Use for_each_of_range() iterator for parsing "ranges"
- Apply link training workaround only on IMX6Q, IMX6SX, IMX6SP (Richard
Zhu)
- Remove redundant dw_pcie_wait_for_link() from imx_pcie_start_link();
since the DWC core does this, imx6 only needs it when retraining for a
faster link speed (Richard Zhu)
- Toggle i.MX95 core reset to align with PHY powerup (Richard Zhu)
- Set SYS_AUX_PWR_DET to work around i.MX95 ERR051624 erratum: in some
cases, the controller can't exit 'L23 Ready' through Beacon or PERST#
deassertion (Richard Zhu)
- Clear GEN3_ZRXDC_NONCOMPL to work around i.MX95 ERR051586 erratum:
controller can't meet 2.5 GT/s ZRX-DC timing when operating at 8 GT/s,
causing timeouts in L1 (Richard Zhu)
- Wait for i.MX95 PLL lock before enabling controller (Richard Zhu)
- Save/restore i.MX95 LUT for suspend/resume (Richard Zhu)
* pci/controller/imx6:
PCI: imx6: Save and restore the LUT setting during suspend/resume for i.MX95 SoC
PCI: imx6: Add PLL lock check for i.MX95 SoC
PCI: imx6: Add workaround for errata ERR051586
PCI: imx6: Add workaround for errata ERR051624
PCI: imx6: Toggle the core reset for i.MX95 PCIe
PCI: imx6: Call dw_pcie_wait_for_link() from start_link() callback only when required
PCI: imx6: Skip link up workaround for newer platforms
- Set PORT_LOGIC_LINK_WIDTH to one lane to make initial link training more
robust; this will not affect the intended link width if all lanes are
functional (Wenbin Yao)
* pci/controller/dwc:
PCI: dwc: Make link training more robust by setting PORT_LOGIC_LINK_WIDTH to one lane
- Check only PCIE_LINKUP, not LTSSM status, to determine whether the link
is up (Shawn Lin)
- Increase N_FTS (used in L0s->L0 transitions) and enable ASPM L0s for Root
Complex and Endpoint modes (Shawn Lin)
- Hide the broken ATS Capability in rockchip_pcie_ep_init() instead of
rockchip_pcie_ep_pre_init() so it stays hidden after PERST# resets
non-sticky registers (Shawn Lin)
- Remove unused PCIE_CLIENT_GENERAL_DEBUG definition (Hans Zhang)
- Organize register and bitfield definitions logically (Hans Zhang)
- Use rockchip_pcie_link_up() to check link up instead of open coding, and
use GENMASK() and FIELD_GET() when possible (Hans Zhang)
- Call phy_power_off() before phy_exit() in rockchip_pcie_phy_deinit()
(Diederik de Haas)
- Return bool (not int) for link-up check in dw_pcie_ops.link_up() and
armada8k, dra7xx, dw-rockchip, exynos, histb, keembay, keystone, kirin,
meson, qcom, qcom-ep, rcar_gen4, spear13xx, tegra194, uniphier, visconti
(Hans Zhang)
- Return bool (not int) for link-up check in mobiveil_pab_ops.link_up() and
layerscape-gen4, mobiveil (Hans Zhang)
- Simplify j721e link-up check (Hans Zhang)
- Convert pci-host-common to a library so platforms that don't need native
host controller drivers don't need to include these helper functions
(Manivannan Sadhasivam)
* pci/controller/dw-rockchip:
PCI: qcom: Replace PERST# sleep time with proper macro
PCI: dw-rockchip: Replace PERST# sleep time with proper macro
PCI: host-common: Convert to library for host controller drivers
PCI: cadence: Simplify J721e link status check
PCI: mobiveil: Return bool from link up check
PCI: dwc: Return bool from link up check
PCI: dw-rockchip: Fix PHY function call sequence in rockchip_pcie_phy_deinit()
PCI: dw-rockchip: Use rockchip_pcie_link_up() to check link up instead of open coding
PCI: dw-rockchip: Reorganize register and bitfield definitions
PCI: dw-rockchip: Remove unused PCIE_CLIENT_GENERAL_DEBUG definition
PCI: dw-rockchip: Move rockchip_pcie_ep_hide_broken_ats_cap_rk3588() to dw_pcie_ep_ops::init()
PCI: dw-rockchip: Enable ASPM L0s capability for both RC and EP modes
PCI: dw-rockchip: Remove PCIE_L0S_ENTRY check from rockchip_pcie_link_up()
# Conflicts:
# drivers/pci/controller/pcie-apple.c
# include/linux/pci-ecam.h
- Drop a runtime PM 'put' to resolve a runtime atomic count underflow (Hans
Zhang)
- Use shared PCIE_MSG_CODE_* definitions and remove duplicate
cdns_pcie_msg_code definitions (Hans Zhang)
- Make the cadence core buildable as a module (Kishon Vijay Abraham I)
- Add cdns_pcie_host_disable() and cdns_pcie_ep_disable() for use by
loadable drivers when they are removed (Siddharth Vadapalli)
- Make j721e buildable as a loadable and removable module (Siddharth
Vadapalli)
- Fix j721e host/endpoint dependencies that result in link failures in
some configs (Arnd Bergmann)
* pci/controller/cadence:
PCI: j721e: Fix host/endpoint dependencies
PCI: j721e: Add support to build as a loadable module
PCI: cadence-ep: Introduce cdns_pcie_ep_disable() helper for cleanup
PCI: cadence-host: Introduce cdns_pcie_host_disable() helper for cleanup
PCI: cadence: Add support to build pcie-cadence library as a kernel module
PCI: cadence: Remove duplicate message code definitions
PCI: cadence: Fix runtime atomic count underflow
- Skip ports disabled in DT when setting up ports (Janne Grunau)
- Add t6020 compatible string (Alyssa Rosenzweig)
- Extract ECAM bridge creation helper from pci_host_common_probe() to
separate driver-specific things like MSI from PCI things (Marc Zyngier)
- Dynamically allocate RID-to_SID bitmap to prepare for SoCs with varying
capabilities (Marc Zyngier)
- Directly set/clear INTx mask bits because T602x dropped the accessors
that could do this without locking (Marc Zyngier)
- Move port PHY registers to their own reg items to accommodate T602x,
which moves them around; retain default offsets for existing DTs that
lack phy%d entries with the reg offsets (Hector Martin)
- Stop polling for core refclk, which doesn't work on T602x and the
bootloader has already done anyway (Hector Martin)
- Use gpiod_set_value_cansleep() when asserting PERST# in probe because
we're allowed to sleep there (Hector Martin)
- Move register offsets into SoC-specific structure (Hector Martin)
- Add T602x PCIe support (Hector Martin)
* pci/controller/apple:
PCI: apple: Add T602x PCIe support
PCI: apple: Abstract register offsets via a SoC-specific structure
PCI: apple: Use gpiod_set_value_cansleep in probe flow
PCI: apple: Drop poll for CORE_RC_PHYIF_STAT_REFCLK
PCI: apple: Move port PHY registers to their own reg items
PCI: apple: Fix missing OF node reference in apple_pcie_setup_port
PCI: apple: Move away from INTMSK{SET,CLR} for INTx and private interrupts
PCI: apple: Dynamically allocate RID-to_SID bitmap
PCI: apple: Move over to standalone probing
PCI: ecam: Allow cfg->priv to be pre-populated from the root port device
PCI: host-generic: Extract an ECAM bridge creation helper from pci_host_common_probe()
dt-bindings: pci: apple,pcie: Add t6020 compatible string
PCI: apple: Set only available ports up
- For fixed-size BARs, retain both the actual size and the possibly larger
size allocated to accommodate iATU alignment requirements (Jerome Brunet)
- Simplify ctrl/SPAD space allocation and avoid allocating more space than
needed (Jerome Brunet)
- Correct MSI-X PBA offset calculations for DesignWare and Cadence endpoint
controllers (Niklas Cassel)
- Align the return value (number of interrupts) encoding for
pci_epc_get_msi()/pci_epc_ops::get_msi() and
pci_epc_get_msix()/pci_epc_ops::get_msix() (Niklas Cassel)
- Align the nr_irqs parameter encoding for
pci_epc_set_msi()/pci_epc_ops::set_msi() and
pci_epc_set_msix()/pci_epc_ops::set_msix() (Niklas Cassel)
* pci/endpoint:
PCI: endpoint: Align pci_epc_set_msix(), pci_epc_ops::set_msix() nr_irqs encoding
PCI: endpoint: Align pci_epc_set_msi(), pci_epc_ops::set_msi() nr_irqs encoding
PCI: endpoint: Align pci_epc_get_msix(), pci_epc_ops::get_msix() return value encoding
PCI: endpoint: Align pci_epc_get_msi(), pci_epc_ops::get_msi() return value encoding
PCI: cadence-ep: Correct PBA offset in .set_msix() callback
PCI: dwc: ep: Correct PBA offset in .set_msix() callback
PCI: endpoint: pci-epf-vntb: Simplify ctrl/SPAD space allocation
PCI: endpoint: Retain fixed-size BAR size as well as aligned size
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEIbPD0id6easf0xsudhRwX5BBoF4FAmg+jmETHHdlaS5saXVA
a2VybmVsLm9yZwAKCRB2FHBfkEGgXiWaCACjYSQcCXW2nnZuWUnGMJq8HD5XGBAH
tNYzOyp2Y4bXEJzfmbHv8UpJynGr3IFKybCnhm0uAQZCmiR5k4CfMvjPQXcJu9LK
7yUI/dTGrRGG7f3NClWK2vXg7ATqzRGiPuPDk2lDcP04aQQWaUMDYe5SXIgcqKyZ
cm2OVHapHGbQ7wA+xXGQcUBb6VJ5+BrQUVOqaEQyl4LURvjaQcn7rVDS0SmEi8gq
42+KDVd8uWYos5dT57HIq9UI5og3PeTvAvHsx26eX8JWNqwXLgvxRH83kstK+GWY
uG3sOm5yRbJvErLpJHnyBOlXDFNw2EBeLC1VyhdJXBR8RabgI+H/mrY3
=4bTC
-----END PGP SIGNATURE-----
Merge tag 'hyperv-next-signed-20250602' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull hyperv updates from Wei Liu:
- Support for Virtual Trust Level (VTL) on arm64 (Roman Kisel)
- Fixes for Hyper-V UIO driver (Long Li)
- Fixes for Hyper-V PCI driver (Michael Kelley)
- Select CONFIG_SYSFB for Hyper-V guests (Michael Kelley)
- Documentation updates for Hyper-V VMBus (Michael Kelley)
- Enhance logging for hv_kvp_daemon (Shradha Gupta)
* tag 'hyperv-next-signed-20250602' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux: (23 commits)
Drivers: hv: Always select CONFIG_SYSFB for Hyper-V guests
Drivers: hv: vmbus: Add comments about races with "channels" sysfs dir
Documentation: hyperv: Update VMBus doc with new features and info
PCI: hv: Remove unnecessary flex array in struct pci_packet
Drivers: hv: Remove hv_alloc/free_* helpers
Drivers: hv: Use kzalloc for panic page allocation
uio_hv_generic: Align ring size to system page
uio_hv_generic: Use correct size for interrupt and monitor pages
Drivers: hv: Allocate interrupt and monitor pages aligned to system page boundary
arch/x86: Provide the CPU number in the wakeup AP callback
x86/hyperv: Fix APIC ID and VP index confusion in hv_snp_boot_ap()
PCI: hv: Get vPCI MSI IRQ domain from DeviceTree
ACPI: irq: Introduce acpi_get_gsi_dispatcher()
Drivers: hv: vmbus: Introduce hv_get_vmbus_root_device()
Drivers: hv: vmbus: Get the IRQ number from DeviceTree
dt-bindings: microsoft,vmbus: Add interrupt and DMA coherence properties
arm64, x86: hyperv: Report the VTL the system boots in
arm64: hyperv: Initialize the Virtual Trust Level field
Drivers: hv: Provide arch-neutral implementation of get_vtl()
Drivers: hv: Enable VTL mode for arm64
...
The j721e driver has a single platform driver that can be built-in or a
loadable module, but it calls two separate backend drivers depending on
whether it is a host or endpoint.
If the two modes are not the same, we can end up with a situation where the
built-in pci-j721e driver tries to call the modular host or endpoint
driver, which causes a link failure:
ld.lld-21: error: undefined symbol: cdns_pcie_ep_setup
>>> referenced by pci-j721e.c
>>> drivers/pci/controller/cadence/pci-j721e.o:(j721e_pcie_probe) in archive vmlinux.a
ld.lld-21: error: undefined symbol: cdns_pcie_host_setup
>>> referenced by pci-j721e.c
>>> drivers/pci/controller/cadence/pci-j721e.o:(j721e_pcie_probe) in archive vmlinux.a
Rework the dependencies so that the 'select' is done by the common Kconfig
symbol, based on which of the two are enabled. Effectively this means that
having one built-in makes the other either built-in or disabled, but all
configurations will now build.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://patch.msgid.link/20250423162523.2060405-1-arnd@kernel.org
The 'pci-j721e.c' driver is the application/glue/wrapper driver for the
Cadence PCIe Controllers on TI SoCs. Implement support for building it as a
loadable module.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://patch.msgid.link/20250417124408.2752248-5-s-vadapalli@ti.com
Introduce the helper function cdns_pcie_ep_disable() which will undo the
configuration performed by cdns_pcie_ep_setup(). Also, export it for use
by the existing callers of cdns_pcie_ep_setup(), thereby allowing them
to cleanup on their exit path.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://patch.msgid.link/20250417124408.2752248-4-s-vadapalli@ti.com
Introduce the helper function cdns_pcie_host_disable() which will undo
the configuration performed by cdns_pcie_host_setup(). Also, export it
for use by existing callers of cdns_pcie_host_setup(), thereby allowing
them to cleanup on their exit path.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://patch.msgid.link/20250417124408.2752248-3-s-vadapalli@ti.com
Currently, the Cadence PCIe controller driver can be built as a built-in
module only. Since PCIe functionality is not a necessity for booting, add
support to build the Cadence PCIe driver as a loadable module as well.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://patch.msgid.link/20250417124408.2752248-2-s-vadapalli@ti.com
This common library will be used as a placeholder for helper functions
shared by the host controller drivers. This avoids placing the host
controller drivers specific helpers in drivers/pci/*.c, to avoid enlarging
the kernel image on platforms that do not use host controller drivers at
all (like x86/ACPI platforms).
Suggested-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20250508-pcie-reset-slot-v4-3-7050093e2b50@linaro.org
The Cadence PCIe controller driver defines message codes in enum
cdns_pcie_msg_code duplicating the existing PCIE_MSG_CODE_* definitions in
drivers/pci/pci.h. The driver only uses ASSERT_INTA and DEASSERT_INTA codes
from this enum.
Remove the redundant Cadence-specific enum definitions and use the ones
available in drivers/pci/pci.h. This helps in avoiding code duplication,
maintaining consistency with the spec, and simplifying the code
maintenance.
Signed-off-by: Hans Zhang <18255117159@163.com>
[mani: commit message rewording]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20250401145023.22948-1-18255117159@163.com
The kdoc for pci_epc_set_msix() says:
"Invoke to set the required number of MSI-X interrupts."
The kdoc for the callback pci_epc_ops->set_msix() says:
"ops to set the requested number of MSI-X interrupts in the MSI-X
capability register"
pci_epc_ops::set_msix() does however expect the parameter 'interrupts' to
be in the encoding as defined by the Table Size field. Nowhere in the
kdoc does it say that the number of interrupts should be in Table Size
encoding.
It is very confusing that the API pci_epc_set_msix() and the callback
function pci_epc_ops::set_msix() both take a parameter named 'interrupts',
but they expect completely different encodings.
Clean up the API and the callback function to have the same semantics,
i.e. the parameter represents the number of interrupts, regardless of the
internal encoding of that value.
Also rename the parameter 'interrupts' to 'nr_irqs', in both the wrapper
function and the callback function, such that the name is unambiguous.
[bhelgaas: more specific subject]
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable+noautosel@kernel.org # this is simply a cleanup
Link: https://patch.msgid.link/20250514074313.283156-14-cassel@kernel.org
The kdoc for pci_epc_set_msi() says:
"Invoke to set the required number of MSI interrupts."
The kdoc for the callback pci_epc_ops::set_msi() says:
"ops to set the requested number of MSI interrupts in the MSI capability
register"
pci_epc_ops::set_msi() does however expect the parameter 'interrupts' to be
in the encoding as defined by the Multiple Message Capable (MMC) field of
the MSI capability structure. Nowhere in the kdoc does it say that the
number of interrupts should be in MMC encoding.
It is very confusing that the API pci_epc_set_msi() and the callback
function pci_epc_ops::set_msi() both take a parameter named 'interrupts',
but they expect completely different encodings.
Clean up the API and the callback function to have the same semantics,
i.e. the parameter represents the number of interrupts, regardless of the
internal encoding of that value.
Also rename the parameter 'interrupts' to 'nr_irqs', in both the wrapper
function and the callback function, such that the name is unambiguous.
[bhelgaas: more specific subject]
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable+noautosel@kernel.org # this is simply a cleanup
Link: https://patch.msgid.link/20250514074313.283156-13-cassel@kernel.org
The kdoc for pci_epc_get_msix() says:
"Invoke to get the number of MSI-X interrupts allocated by the RC"
The kdoc for the callback pci_epc_ops->get_msix() says:
"ops to get the number of MSI-X interrupts allocated by the RC from the
MSI-X capability register"
pci_epc_ops::get_msix() does however return the number of interrupts in the
encoding as defined by the Table Size field. Nowhere in the kdoc does it
say that the returned number of interrupts is in Table Size encoding.
It is very confusing that the API pci_epc_get_msix() and the callback
function pci_epc_ops::get_msix() don't return the same value.
Clean up the API and the callback function to have the same semantics,
i.e. return the number of interrupts, regardless of the internal encoding
of that value.
[bhelgaas: more specific subject]
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Cc: stable+noautosel@kernel.org # this is simply a cleanup
Link: https://patch.msgid.link/20250514074313.283156-12-cassel@kernel.org
The kdoc for API pci_epc_get_msi() says:
"Invoke to get the number of MSI interrupts allocated by the RC"
The kdoc for the callback pci_epc_ops::get_msi() says:
"ops to get the number of MSI interrupts allocated by the RC from
the MSI capability register"
pci_epc_ops::get_msi() does however return the number of interrupts in the
encoding as defined by the Multiple Message Enable (MME) field of the MSI
Capability structure.
Nowhere in the kdoc does it say that the returned number of interrupts is
in MME encoding. It is very confusing that the API pci_epc_get_msi() and
the callback function pci_epc_ops::get_msi() don't return the same value.
Clean up the API and the callback function to have the same semantics,
i.e. return the number of interrupts, regardless of the internal encoding
of that value.
[bhelgaas: more specific subject]
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Cc: stable+noautosel@kernel.org # this is simply a cleanup
Link: https://patch.msgid.link/20250514074313.283156-11-cassel@kernel.org
While cdns_pcie_ep_set_msix() writes the Table Size field correctly (N-1),
the calculation of the PBA offset is wrong because it calculates space for
(N-1) entries instead of N.
This results in the following QEMU error when using PCI passthrough on a
device which relies on the PCI endpoint subsystem:
failed to add PCI capability 0x11[0x50]@0xb0: table & pba overlap, or they don't fit in BARs, or don't align
Fix the calculation of PBA offset in the MSI-X capability.
[bhelgaas: more specific subject and commit log]
Fixes: 3ef5d16f50 ("PCI: cadence: Add MSI-X support to Endpoint driver")
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250514074313.283156-10-cassel@kernel.org
While dw_pcie_ep_set_msix() writes the Table Size field correctly (N-1),
the calculation of the PBA offset is wrong because it calculates space for
(N-1) entries instead of N.
This results in the following QEMU error when using PCI passthrough on a
device which relies on the PCI endpoint subsystem:
failed to add PCI capability 0x11[0x50]@0xb0: table & pba overlap, or they don't fit in BARs, or don't align
Fix the calculation of PBA offset in the MSI-X capability.
[bhelgaas: more specific subject and commit log]
Fixes: 83153d9f36 ("PCI: endpoint: Fix ->set_msix() to take BIR and offset as arguments")
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250514074313.283156-9-cassel@kernel.org
- Switch the MSI decriptor locking to lock guards
- Replace a broken and naive implementation of PCI/MSI-X control word
updates in the PCI/TPH driver with a properly serialized variant in the
PCI/MSI core code.
- Remove the MSI descriptor abuse in the SCCI/UFS/QCOM driver by
replacing the direct access to the MSI descriptors with the proper API
function calls. People will never understand that APIs exist for a
reason...
- Provide core infrastructre for the upcoming PCI endpoint library
extensions. Currently limited to ARM GICv3+, but in theory extensible
to other architectures.
- Provide a MSI domain::teardown() callback, which allows drivers to undo
the effects of the prepare() callback.
- Move the MSI domain::prepare() callback invocation to domain creation
time to avoid redundant (and in case of ARM/GIC-V3-ITS confusing)
invocations on every allocation.
In combination with the new teardown callback this removes some ugly
hacks in the GIC-V3-ITS driver, which pretended to work around the
short comings of the core code so far. With this update the code is
correct by design and implementation.
- Make the irqchip MSI library globally available, provide a MSI parent
domain creation helper and convert a bunch of (PCI/)MSI drivers over to
the modern MSI parent mechanism. This is the first step to get rid of
at least one incarnation of the three PCI/MSI management schemes.
- The usual small cleanups and improvements
-----BEGIN PGP SIGNATURE-----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=OBMj
-----END PGP SIGNATURE-----
Merge tag 'irq-msi-2025-05-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull MSI updates from Thomas Gleixner:
"Updates for the MSI subsystem (core code and PCI):
- Switch the MSI descriptor locking to lock guards
- Replace a broken and naive implementation of PCI/MSI-X control word
updates in the PCI/TPH driver with a properly serialized variant in
the PCI/MSI core code.
- Remove the MSI descriptor abuse in the SCCI/UFS/QCOM driver by
replacing the direct access to the MSI descriptors with the proper
API function calls. People will never understand that APIs exist
for a reason...
- Provide core infrastructre for the upcoming PCI endpoint library
extensions. Currently limited to ARM GICv3+, but in theory
extensible to other architectures.
- Provide a MSI domain::teardown() callback, which allows drivers to
undo the effects of the prepare() callback.
- Move the MSI domain::prepare() callback invocation to domain
creation time to avoid redundant (and in case of ARM/GIC-V3-ITS
confusing) invocations on every allocation.
In combination with the new teardown callback this removes some
ugly hacks in the GIC-V3-ITS driver, which pretended to work around
the short comings of the core code so far. With this update the
code is correct by design and implementation.
- Make the irqchip MSI library globally available, provide a MSI
parent domain creation helper and convert a bunch of (PCI/)MSI
drivers over to the modern MSI parent mechanism. This is the first
step to get rid of at least one incarnation of the three PCI/MSI
management schemes.
- The usual small cleanups and improvements"
* tag 'irq-msi-2025-05-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (33 commits)
PCI/MSI: Use bool for MSI enable state tracking
PCI: tegra: Convert to MSI parent infrastructure
PCI: xgene: Convert to MSI parent infrastructure
PCI: apple: Convert to MSI parent infrastructure
irqchip/msi-lib: Honour the MSI_FLAG_NO_AFFINITY flag
irqchip/mvebu: Convert to msi_create_parent_irq_domain() helper
irqchip/gic: Convert to msi_create_parent_irq_domain() helper
genirq/msi: Add helper for creating MSI-parent irq domains
irqchip: Make irq-msi-lib.h globally available
irqchip/gic-v3-its: Use allocation size from the prepare call
genirq/msi: Engage the .msi_teardown() callback on domain removal
genirq/msi: Move prepare() call to per-device allocation
irqchip/gic-v3-its: Implement .msi_teardown() callback
genirq/msi: Add .msi_teardown() callback as the reverse of .msi_prepare()
irqchip/gic-v3-its: Add support for device tree msi-map and msi-mask
dt-bindings: PCI: pci-ep: Add support for iommu-map and msi-map
irqchip/gic-v3-its: Set IRQ_DOMAIN_FLAG_MSI_IMMUTABLE for ITS
irqdomain: Add IRQ_DOMAIN_FLAG_MSI_IMMUTABLE and irq_domain_is_msi_immutable()
platform-msi: Add msi_remove_device_irq_domain() in platform_device_msi_free_irqs_all()
genirq/msi: Rename msi_[un]lock_descs()
...
struct pci_packet contains a "message" field that is a flex array
of struct pci_message. struct pci_packet is usually followed by a
second struct in a containing struct that is defined locally in
individual functions in pci-hyperv.c. As such, the compiler
flag -Wflex-array-member-not-at-end (introduced in gcc-14) generates
multiple warnings such as:
drivers/pci/controller/pci-hyperv.c:3809:35: warning: structure
containing a flexible array member is not at the end of another
structure [-Wflex-array-member-not-at-end]
The Linux kernel intends to introduce this compiler flag in standard
builds, so the current code is problematic in generating these warnings.
The "message" field is used only to locate the start of the second
struct, and not as an array. Because the second struct can be
addressed directly, the "message" field is not really necessary.
Rather than try to fix its usage to meet the requirements of
-Wflex-array-member-not-at-end, just eliminate the field and
either directly reference the second struct, or use "pkt + 1"
when "pkt" is dynamically allocated.
Reported-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Michael Kelley <mhklinux@outlook.com>
Link: https://lore.kernel.org/r/20250514044440.48924-1-mhklinux@outlook.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Message-ID: <20250514044440.48924-1-mhklinux@outlook.com>
The hyperv-pci driver uses ACPI for MSI IRQ domain configuration on
arm64. It won't be able to do that in the VTL mode where only DeviceTree
can be used.
Update the hyperv-pci driver to get vPCI MSI IRQ domain in the DeviceTree
case, too.
Signed-off-by: Roman Kisel <romank@linux.microsoft.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Link: https://lore.kernel.org/r/20250428210742.435282-12-romank@linux.microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Message-ID: <20250428210742.435282-12-romank@linux.microsoft.com>
In an effort to move ARM64 away from the legacy MSI setup, convert the
Tegra PCIe driver to the MSI-parent infrastructure and let each device have
its own MSI domain.
[ tglx: Moved the struct out of the function call argument ]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250513172819.2216709-10-maz@kernel.org
In an effort to move ARM64 away from the legacy MSI setup, convert the
XGENE PCIe driver to the MSI-parent infrastructure and let each device have
its own MSI domain.
[ tglx: Moved the struct out of the function call argument ]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250513172819.2216709-9-maz@kernel.org
In an effort to move ARM64 away from the legacy MSI setup, convert the
Apple PCIe driver to the MSI-parent infrastructure and let each device have
its own MSI domain.
[ tglx: Moved the struct out of the function call argument ]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Link: https://lore.kernel.org/all/20250513172819.2216709-8-maz@kernel.org
irq_domain_add_linear() is going away as being obsolete now. Switch to
the preferred irq_domain_create_linear(). That differs in the first
parameter: It takes more generic struct fwnode_handle instead of struct
device_node. Therefore, of_fwnode_handle() is added around the
parameter.
Note some of the users can likely use dev->fwnode directly instead of
indirect of_fwnode_handle(dev->of_node). But dev->fwnode is not
guaranteed to be set for all, so this has to be investigated on case to
case basis (by people who can actually test with the HW).
[ tglx: Fix up subject prefix and convert the new instance in
dwc/pcie-amd-mdb.c ]
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250319092951.37667-30-jirislaby@kernel.org
When PTM is enabled, PTM_UPDATING interrupt will be fired for each PTM
context update, which will be once every 10ms in the case of auto context
update. Since the interrupt is not strictly needed for making use of PTM,
mask it to avoid the overhead of processing it.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Link: https://patch.msgid.link/20250505-pcie-ptm-v4-4-02d26d51400b@linaro.org
Synopsys Designware PCIe IPs support PTM capability as defined in the PCIe
spec r6.0, sec 6.21. The PTM context information is exposed through Vendor
Specific Extended Capability (VSEC) registers on supported controller
implementation.
Hence, add support for exposing these context information to userspace
through the debugfs interface for the DWC controllers (both RC and EP).
Currently, only Qcom controllers are supported. For adding support for
other DWC vendor controllers, dwc_pcie_ptm_vsec_ids[] needs to be extended.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Link: https://patch.msgid.link/20250505-pcie-ptm-v4-3-02d26d51400b@linaro.org
Upcoming PTM debugfs interface relies on the DWC PCIe mode to expose the
relevant debugfs attributes to userspace. So pass the mode to
dwc_pcie_debugfs_init() API from host and ep drivers and save it in
'struct dw_pcie::mode'.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Link: https://patch.msgid.link/20250505-pcie-ptm-v4-2-02d26d51400b@linaro.org
Replace explicit if-else condition with direct return statement in
j721e_pcie_link_up(). This reduces code verbosity while maintaining
the same logic for detecting PCIe link completion.
Signed-off-by: Hans Zhang <18255117159@163.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Link: https://patch.msgid.link/20250510160710.392122-4-18255117159@163.com
PCIe link status check is supposed to return a boolean to indicate whether
the link is up or not. So update ls_g4_pcie_link_up() to return bool and
also simplify the LTSSM state check.
Signed-off-by: Hans Zhang <18255117159@163.com>
[mani: commit message rewording]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Link: https://patch.msgid.link/20250510160710.392122-3-18255117159@163.com
PCIe link status check is supposed to return a boolean to indicate whether
the link is up or not. So, modify the link_up callbacks and
dw_pcie_link_up() function to return bool instead of int.
Signed-off-by: Hans Zhang <18255117159@163.com>
[mani: commit message reword]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Link: https://patch.msgid.link/20250510160710.392122-2-18255117159@163.com
Previously, the debugfs directory was unconditionally created in
tegra_pcie_config_rp() regardless of the CONFIG_PCIEASPM setting.
This led to unnecessary directory creation when ASPM support was disabled
since only ASPM state count was exposed through debugfs.
Hence, move the debugfs directory creation into init_debugfs() which is
conditionally compiled based on CONFIG_PCIEASPM. This ensures that both
the directory and 'aspm_state_cnt' entry are only created when ASPM is
enabled and avoids cluttering debugfs with empty directories when ASPM is
disabled.
Signed-off-by: Hans Zhang <18255117159@163.com>
[mani: subject and description change]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://patch.msgid.link/20250407124331.69459-1-18255117159@163.com
As per DWC PCIe registers description 4.30a, section 1.13.43, NUM_OF_LANES
named as PORT_LOGIC_LINK_WIDTH in PCIe DWC driver, is referred to as the
"Predetermined Number of Lanes" in PCIe r6.0, sec 4.2.7.2.1, which explains
the conditions required to enter Polling.Configuration:
Next state is Polling.Configuration after at least 1024 TS1 Ordered Sets
were transmitted, and all Lanes that detected a Receiver during Detect
receive eight consecutive training sequences ...
Otherwise, after a 24 ms timeout the next state is:
Polling.Configuration if,
(i) Any Lane, which detected a Receiver during Detect, received eight
consecutive training sequences ... and a minimum of 1024 TS1 Ordered
Sets are transmitted after receiving one TS1 or TS2 Ordered Set.
And
(ii) At least a predetermined set of Lanes that detected a Receiver
during Detect have detected an exit from Electrical Idle at least
once since entering Polling.Active.
Note: This may prevent one or more bad Receivers or Transmitters
from holding up a valid Link from being configured, and allow for
additional training in Polling.Configuration. The exact set of
predetermined Lanes is implementation specific.
Note: Any Lane that receives eight consecutive TS1 or TS2 Ordered
Sets should have detected an exit from Electrical Idle at least
once since entering Polling.Active.
In a PCIe link supporting multiple lanes, if PORT_LOGIC_LINK_WIDTH is set
to lane width the hardware supports, all lanes that detect a receiver
during the Detect phase must receive eight consecutive training sequences.
Otherwise, LTSSM will not enter Polling.Configuration and link training
will fail.
Therefore, always set PORT_LOGIC_LINK_WIDTH to 1, regardless of the number
of lanes the port actually supports, to make link up more robust. This
setting will not affect the intended link width if all lanes are
functional. Additionally, the link can still be established with at least
one lane if other lanes are faulty.
Co-developed-by: Qiang Yu <quic_qianyu@quicinc.com>
Signed-off-by: Qiang Yu <quic_qianyu@quicinc.com>
Signed-off-by: Wenbin Yao <quic_wenbyao@quicinc.com>
[mani: subject change]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[bhelgaas: update PCIe spec citation, format quote]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Niklas Cassel <cassel@kernel.org>
Link: https://patch.msgid.link/20250422103623.462277-1-quic_wenbyao@quicinc.com
The documentation for the phy_power_off() function explicitly says that it
must be called before phy_exit().
Hence, follow the same rule in rockchip_pcie_phy_deinit().
Fixes: 0e898eb8df ("PCI: rockchip-dwc: Add Rockchip RK356X host controller driver")
Signed-off-by: Diederik de Haas <didi.debian@cknow.org>
[mani: commit message change]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
Cc: stable@vger.kernel.org # v5.15+
Link: https://patch.msgid.link/20250417142138.1377451-1-didi.debian@cknow.org
Some of the callers of rockchip_pcie_link_up() are open coding the
rockchip_pcie_link_up() function, leading to code duplication. So switch
them to use rockchip_pcie_link_up() function.
Also, use the FIELD_GET() macro to simplify the link up check in
rockchip_pcie_link_up().
Signed-off-by: Hans Zhang <18255117159@163.com>
[mani: subject and description rewording]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://patch.msgid.link/20250427125316.99627-4-18255117159@163.com
Register definitions were scattered with ambiguous names (e.g.,
PCIE_RDLH_LINK_UP_CHGED in PCIE_CLIENT_INTR_STATUS_MISC) and lacked
hierarchical grouping.
Group registers and their associated bitfields logically. This improves
maintainability and aligns the code with hardware documentation.
Signed-off-by: Hans Zhang <18255117159@163.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://patch.msgid.link/20250427125316.99627-3-18255117159@163.com
The PCIE_CLIENT_GENERAL_DEBUG register offset is defined but never
used in the driver. It's presence adds noise to the register map.
Remove this unused definition to keep the register list minimal and aligned
with actual hardware usage.
Signed-off-by: Hans Zhang <18255117159@163.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://patch.msgid.link/20250427125316.99627-2-18255117159@163.com
The look up table (LUT) setting would be lost during the PCIe suspend on
i.MX95 SoC. So to ensure proper functionality after resume, save it during
suspend and restore it while resuming.
Fixes: 9d6b1bd6b3 ("PCI: imx6: Add i.MX8MQ, i.MX8Q and i.MX95 PM support")
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
[mani: subject and description rewording]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://patch.msgid.link/20250416081314.3929794-8-hongxing.zhu@nxp.com
PLL lock is required to ensure that the PLL clock is stable before enabling
the controller in i.MX95 SoC.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
[mani: subject and description rewording]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://patch.msgid.link/20250416081314.3929794-7-hongxing.zhu@nxp.com
ERR051586: Compliance with 8GT/s Receiver Impedance ECN.
The default value of GEN3_RELATED_OFF[GEN3_ZRXDC_NONCOMPL] is 1 which
makes receiver non-compliant with the ZRX-DC parameter for 2.5 GT/s when
operating at 8 GT/s or higher. It causes unnecessary timeout in L1.
So the workaround is to set GEN3_RELATED_OFF[GEN3_ZRXDC_NONCOMPL] to 0.
Add this workaround in the dw_pcie_host_ops::post_init() callback for
i.MX95 platforms.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
[mani: subject and description rewording]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://patch.msgid.link/20250416081314.3929794-6-hongxing.zhu@nxp.com
ERR051624: The Controller Without Vaux Cannot Exit L23 Ready Through Beacon
or PERST# De-assertion
When the auxiliary power is not available, the controller cannot exit from
L23 Ready with beacon or PERST# de-assertion when main power is not
removed. So the workaround is to set SS_RW_REG_1[SYS_AUX_PWR_DET] to 1.
This workaround is required irrespective of whether Vaux is supplied to the
link partner or not.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
[mani: subject and description rewording]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://patch.msgid.link/20250416081314.3929794-5-hongxing.zhu@nxp.com
Add toggling core reset for i.MX95 to align with PHY's power-up sequence.
Note that the register is named as IMX95_PCIE_COLD_RST in hardware, though
it is used to reset the PCIe core.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[mani: subject and description rewording]
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20250416081314.3929794-4-hongxing.zhu@nxp.com
Since the DWC driver is already calling dw_pcie_wait_for_link() after
calling the start_link() callback, remove the redundant
dw_pcie_wait_for_link() call from imx_pcie_start_link(). It is still
required to call this function for controllers supporting Gen 2 and higher
link speeds.
Suggested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
[mani: subject and description rewording]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20250416081314.3929794-3-hongxing.zhu@nxp.com
The current link setup procedure has one workaround to detect the devices
behind PCIe switches on some i.MX6 platforms. But this workaround is not
needed on recent i.MX7 platforms. So skip the workaround for platforms that
do not set the flag and start LTSSM directly.
Also, change the flag name from IMX_PCIE_FLAG_IMX_SPEED_CHANGE to
IMX_PCIE_FLAG_SPEED_CHANGE_WORKAROUND to match the usecase.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
[mani: subject and description rewording]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://patch.msgid.link/20250416081314.3929794-2-hongxing.zhu@nxp.com
In the case of PERST# deassert, non-sticky registers will get reset to
their hardware default state and EXT_CAP registers are one among them. But
since the broken ATS cap is hidden only in dw_pcie_ep_ops::pre_init()
callback which is not gettting called during PERST# deassert, it results in
the capability getting advertised again.
So move it to dw_pcie_ep_ops::init() to fix it.
Suggested-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
[mani: subject and description rewording]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Tested-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://patch.msgid.link/1744594109-209312-1-git-send-email-shawn.lin@rock-chips.com
L0s capability isn't enabled on all Rockchip SoCs by default, so enable it
in order to make ASPM L0s work on Rockchip platforms.
Testing the L0s for a long time revealed that the default N_FTS value of
210 in the hardware doesn't work stable and causes LTSSM to switch between
L0s and Recovery states. This leads to long exit latency and also causes
link down sometimes. So override the value to the max 255, which seems to
work fine under both PHYs used on Rockchip platforms.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
[mani: subject and description rewording]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://patch.msgid.link/1744850111-236269-2-git-send-email-shawn.lin@rock-chips.com
rockchip_pcie_link_up() currently has two issues:
1. Value 0x11 of PCIE_L0S_ENTRY corresponds to L0 state, not L0S. So the
naming is wrong from the very beginning.
2. Checking for value 0x11 treats other states like L0S and L1 as link
down, which is wrong.
Hence, remove the PCIE_L0S_ENTRY check and also its definition. This allows
adding ASPM support in the successive commits.
Fixes: 0e898eb8df ("PCI: rockchip-dwc: Add Rockchip RK356X host controller driver")
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
[mani: commit message rewording]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/1744850111-236269-1-git-send-email-shawn.lin@rock-chips.com
This version of the hardware moved around a bunch of registers, so we
avoid the old compatible for these and introduce register offset
structures to handle the differences.
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Tested-by: Janne Grunau <j@jannau.net>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Link: https://patch.msgid.link/20250401091713.2765724-14-maz@kernel.org
Newer versions of the Apple PCIe block have a bunch of small, but
annoying differences.
In order to embrace this diversity of implementations, move the
currently hardcoded offsets into a hw_info structure. Future SoCs
will provide their own structure describing the applicable offsets.
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
[maz: split from original patch to only address T8103]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Tested-by: Janne Grunau <j@jannau.net>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Link: https://patch.msgid.link/20250401091713.2765724-13-maz@kernel.org
This is checking a core refclk in per-port setup which doesn't make a
lot of sense, and the bootloader needs to have gone through this anyway.
It doesn't work on T602x, so just drop it across the board.
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Tested-by: Janne Grunau <j@jannau.net>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Link: https://patch.msgid.link/20250401091713.2765724-11-maz@kernel.org
T602x PCIe cores move these registers around. Instead of hardcoding in
another offset, let's move them into their own reg entries. This matches
what Apple does on macOS device trees too.
Maintains backwards compatibility with old DTs by using the old offsets.
Note that we open code devm_platform_ioremap_resource_byname() to avoid
error messages on older platforms with missing resources in the pcie
node. ("pcie-apple 590000000.pcie: invalid resource (null)" on probe)
Co-developed-by: Janne Grunau <j@jannau.net>
Signed-off-by: Janne Grunau <j@jannau.net>
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Tested-by: Janne Grunau <j@jannau.net>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Link: https://patch.msgid.link/20250401091713.2765724-10-maz@kernel.org
In the success path, we hang onto a reference to the node, so make sure
to grab one. The caller iterator puts our borrowed reference when we
return.
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Tested-by: Janne Grunau <j@jannau.net>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Link: https://patch.msgid.link/20250401091713.2765724-9-maz@kernel.org
T602x seems to have dropped the rather useful SET/CLR accessors
to the masking register.
Instead, let's use the mask register directly, and wrap it with
a brand new spinlock. No, this isn't moving in the right direction.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Tested-by: Janne Grunau <j@jannau.net>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Link: https://patch.msgid.link/20250401091713.2765724-8-maz@kernel.org
As we move towards supporting SoCs with varying RID-to-SID mapping
capabilities, turn the static SID tracking bitmap into a dynamically
allocated one. The current allocation size is still the same, but
that's about to change.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Tested-by: Janne Grunau <j@jannau.net>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Link: https://patch.msgid.link/20250401091713.2765724-7-maz@kernel.org
Now that we have the required infrastructure, split the Apple PCIe
setup into two categories:
- stuff that has to do with PCI setup stays in the .init() callback
- stuff that is just driver gunk (such as MSI setup) goes into a
probe routine, which will eventually call into the host-common
code
The result is a far more logical setup process.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Tested-by: Janne Grunau <j@jannau.net>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Link: https://patch.msgid.link/20250401091713.2765724-6-maz@kernel.org
pci_host_common_probe() is an extremely useful helper, as it
abstracts away most of the gunk that a "mostly-ECAM-compliant"
device driver needs.
However, it is structured as a probe function, meaning that a lot
of the driver-specific setup has to happen in a .init() callback,
after the bridge and config space have been instantiated.
This is a bit awkward, and results in a number of convolutions
that could be avoided if the host-common code was more like
a library.
Introduce a pci_host_common_init() helper that does exactly that,
taking the platform device and a struct pci_ecam_op as parameters.
This can then be called from the probe routine, and a lot of the
code that isn't relevant to PCI setup moved away from the .init()
callback. This also removes the dependency on the device match
data, which is an oddity.
Signed-off-by: Marc Zyngier <maz@kernel.org>
[mani: fixed spelling mistakes]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Tested-by: Janne Grunau <j@jannau.net>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Link: https://patch.msgid.link/20250401091713.2765724-4-maz@kernel.org
Add IPQ5018 platform with is based on Qcom IP rev. 2.9.0 and Synopsys IP
rev. 5.00a.
The platform itself has two PCIe Gen2 controllers: one single-lane and
one dual-lane. So add the IPQ5018 compatible and re-use 2_9_0 ops.
Signed-off-by: Nitheesh Sekar <quic_nsekar@quicinc.com>
Signed-off-by: Sricharan R <quic_srichara@quicinc.com>
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://patch.msgid.link/20250326-ipq5018-pcie-v7-4-e1828fef06c9@outlook.com
PCIe equalization presets are predefined settings used to optimize signal
integrity by compensating for signal loss and distortion in high-speed data
transmission.
Based upon the number of lanes and the data rate supported, write the
preset data read from the device tree in to the lane equalization control
registers. These preset values will be used by the controller during the
LTSSM lane equalization procedure.
Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
[mani: reworded the commit message and comments in the driver]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://patch.msgid.link/20250328-preset_v6-v9-5-22cfa0490518@oss.qualcomm.com
If the call to pci_host_probe() in cdns_pcie_host_setup() fails, PM
runtime count is decremented in the error path using pm_runtime_put_sync().
But the runtime count is not incremented by this driver, but only by the
callers (cdns_plat_pcie_probe/j721e_pcie_probe). And the callers also
decrement the runtime PM count in their error path. So this leads to the
below warning from the PM core:
"runtime PM usage count underflow!"
So fix it by getting rid of pm_runtime_put_sync() in the error path and
directly return the errno.
Fixes: 49e427e6bd ("Merge branch 'pci/host-probe-refactor'")
Signed-off-by: Hans Zhang <18255117159@163.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://patch.msgid.link/20250419133058.162048-1-18255117159@163.com
RK3399 can raise INTx interrupts, as can be seen by
rockchip_pcie_ep_send_intx_irq().
This is also in line with the register description of
PCIE_CLIENT_LEGACY_INT_CTRL, section "17.6.3 PCIe Client Detail Register
Description" of the RK3399 TRM.
Thus, mark RK3399 as intx_capable.
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://patch.msgid.link/20250416142749.336298-2-cassel@kernel.org
Iterating over disabled ports results in of_irq_parse_raw() parsing
the wrong "interrupt-map" entries, as it takes the status of the node
into account.
This became apparent after disabling unused PCIe ports in the Apple
Silicon device trees instead of deleting them.
Switching from for_each_child_of_node_scoped() to
for_each_available_child_of_node_scoped() solves this issue.
Fixes: 1e33888fbe ("PCI: apple: Add initial hardware bring-up")
Fixes: a0189fdfb7 ("arm64: dts: apple: t8103: Disable unused PCIe ports")
Signed-off-by: Janne Grunau <j@jannau.net>
Signed-off-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Tested-by: Janne Grunau <j@jannau.net>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/asahi/20230214-apple_dts_pcie_disable_unused-v1-0-5ea0d3ddcde3@jannau.net/
Link: https://lore.kernel.org/asahi/1ea2107a-bb86-8c22-0bbc-82c453ab08ce@linaro.org/
Link: https://patch.msgid.link/20250401091713.2765724-2-maz@kernel.org
The mvebu "ranges" is a bit unusual with its own encoding of addresses,
but it's still just normal "ranges" as far as parsing is concerned.
Convert mvebu_get_tgt_attr() to use the for_each_of_range() iterator
instead of open coding the parsing.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://patch.msgid.link/20241107153255.2740610-1-robh@kernel.org
If the num-lanes property is not present in the devicetree, update
pci->num_lanes with the hardware supported maximum link width using
the newly introduced dw_pcie_link_get_max_link_width() API.
The API is used to get the Maximum Link Width (MLW) of the controller.
Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
[mani: reworded commit message a bit]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://patch.msgid.link/20250328-preset_v6-v9-3-22cfa0490518@oss.qualcomm.com
On rcar-gen4, the ep BAR4 has a fixed size of 256B. Document this
constraint in the epc features of the platform.
Fixes: e311b3834d ("PCI: rcar-gen4: Add endpoint mode support")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://patch.msgid.link/20250328-rcar-gen4-bar4-v1-1-10bb6ce9ee7f@baylibre.com
The order of rockchip_pci_core_rsts introduced in the offending commit
followed the previous comment that warned not to reorder them. But the
commit failed to take into account that reset_control_bulk_deassert()
deasserts the resets in reverse order. So this leads to the link getting
downgraded to 2.5 GT/s.
Hence, restore the deassert order and also add back the comments for
rockchip_pci_core_rsts.
Tested on NanoPC-T4 with Samsung 970 Pro.
Fixes: 18715931a5 ("PCI: rockchip: Simplify reset control handling by using reset_control_bulk*() function")
Signed-off-by: Jensen Huang <jensenhuang@friendlyarm.com>
[mani: reworded the commit message and the comment above rockchip_pci_core_rsts]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://patch.msgid.link/20250328105822.3946767-1-jensenhuang@friendlyarm.com
Convert the code to use the new guard(msi_descs_lock).
No functional change intended.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Acked-by: Wei Liu <wei.liu@kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/all/20250319105506.624838146@linutronix.de
of_node_to_fwnode() is irqdomain's reimplementation of the "officially"
defined of_fwnode_handle(). The former is in the process of being removed,
so use the latter instead.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20250319092951.37667-8-jirislaby@kernel.org
-----BEGIN PGP SIGNATURE-----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=gM1i
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.15-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Enable Configuration RRS SV, which makes device readiness visible,
early instead of during child bus scanning (Bjorn Helgaas)
- Log debug messages about reset methods being used (Bjorn Helgaas)
- Avoid reset when it has been disabled via sysfs (Nishanth
Aravamudan)
- Add common pci-ep-bus.yaml schema for exporting several peripherals
of a single PCI function via devicetree (Andrea della Porta)
- Create DT nodes for PCI host bridges to enable loading device tree
overlays to create platform devices for PCI devices that have
several features that require multiple drivers (Herve Codina)
Resource management:
- Enlarge devres table[] to accommodate bridge windows, ROM, IOV
BARs, etc., and validate BAR index in devres interfaces (Philipp
Stanner)
- Fix typo that repeatedly distributed resources to a bridge instead
of iterating over subordinate bridges, which resulted in too little
space to assign some BARs (Kai-Heng Feng)
- Relax bridge window tail sizing for optional resources, e.g., IOV
BARs, to avoid failures when removing and re-adding devices (Ilpo
Järvinen)
- Allow drivers to enable devices even if we haven't assigned
optional IOV resources to them (Ilpo Järvinen)
- Rework handling of optional resources (IOV BARs, ROMs) to reduce
failures if we can't allocate them (Ilpo Järvinen)
- Fix a NULL dereference in the SR-IOV VF creation error path (Shay
Drory)
- Fix s390 mmio_read/write syscalls, which didn't cause page faults
in some cases, which broke vfio-pci lazy mapping on first access
(Niklas Schnelle)
- Add pdev->non_mappable_bars to replace CONFIG_VFIO_PCI_MMAP, which
was disabled only for s390 (Niklas Schnelle)
- Support mmap of PCI resources on s390 except for ISM devices
(Niklas Schnelle)
ASPM:
- Delay pcie_link_state deallocation to avoid dangling pointers that
cause invalid references during hot-unplug (Daniel Stodden)
Power management:
- Allow PCI bridges to go to D3Hot when suspending on all non-x86
systems (Manivannan Sadhasivam)
Power control:
- Create pwrctrl devices in pci_scan_device() to make it more
symmetric with pci_pwrctrl_unregister() and make pwrctrl devices
for PCI bridges possible (Manivannan Sadhasivam)
- Unregister pwrctrl devices in pci_destroy_dev() so DOE, ASPM, etc.
can still access devices after pci_stop_dev() (Manivannan
Sadhasivam)
- If there's a pwrctrl device for a PCI device, skip scanning it
because the pwrctrl core will rescan the bus after the device is
powered on (Manivannan Sadhasivam)
- Add a pwrctrl driver for PCI slots based on voltage regulators
described via devicetree (Manivannan Sadhasivam)
Bandwidth control:
- Add set_pcie_speed.sh to TEST_PROGS to fix issue when executing the
set_pcie_cooling_state.sh test case (Yi Lai)
- Avoid a NULL pointer dereference when we run out of bus numbers to
assign for a bridge secondary bus (Lukas Wunner)
Hotplug:
- Drop superfluous pci_hotplug_slot_list, try_module_get() calls, and
NULL pointer checks (Lukas Wunner)
- Drop shpchp module init/exit logging, replace shpchp dbg() with
ctrl_dbg(), and remove unused dbg(), err(), info(), warn() wrappers
(Ilpo Järvinen)
- Drop 'shpchp_debug' module parameter in favor of standard dynamic
debugging (Ilpo Järvinen)
- Drop unused cpcihp .get_power(), .set_power() function pointers
(Guilherme Giacomo Simoes)
- Disable hotplug interrupts in portdrv only when pciehp is not
enabled to avoid issuing two hotplug commands too close together
(Feng Tang)
- Skip pciehp 'device replaced' check if the device has been removed
to address a deadlock when resuming after a device was removed
during system sleep (Lukas Wunner)
- Don't enable pciehp hotplug interupt when resuming in poll mode
(Ilpo Järvinen)
Virtualization:
- Fix bugs in 'pci=config_acs=' kernel command line parameter (Tushar
Dave)
DOE:
- Expose supported DOE features via sysfs (Alistair Francis)
- Allow DOE support to be enabled even if CXL isn't enabled (Alistair
Francis)
Endpoint framework:
- Convert PCI device data so pci-epf-test works correctly on
big-endian endpoint systems (Niklas Cassel)
- Add BAR_RESIZABLE type to endpoint framework and add DWC core
support for EPF drivers to set BAR_RESIZABLE type and size (Niklas
Cassel)
- Fix pci-epf-test double free that causes an oops if the host
reboots and PERST# deassertion restarts endpoint BAR allocation
(Christian Bruel)
- Fix endpoint BAR testing so tests can skip disabled BARs instead of
reporting them as failures (Niklas Cassel)
- Widen endpoint test BAR size variable to accommodate BARs larger
than INT_MAX (Niklas Cassel)
- Remove unused tools 'pci' build target left over after moving tests
to tools/testing/selftests/pci_endpoint (Jianfeng Liu)
Altera PCIe controller driver:
- Add DT binding and driver support for Agilex family (P-Tile,
F-Tile, R-Tile) (Matthew Gerlach and D M, Sharath Kumar)
AMD MDB PCIe controller driver:
- Add DT binding and driver for AMD MDB (Multimedia DMA Bridge)
(Thippeswamy Havalige)
Broadcom STB PCIe controller driver:
- Add BCM2712 MSI-X DT binding and interrupt controller drivers and
add softdep on irq_bcm2712_mip driver to ensure that it is loaded
first (Stanimir Varbanov)
- Expand inbound window map to 64GB so it can accommodate BCM2712
(Stanimir Varbanov)
- Add BCM2712 support and DT updates (Stanimir Varbanov)
- Apply link speed restriction before bringing link up, not after
(Jim Quinlan)
- Update Max Link Speed in Link Capabilities via the internal
writable register, not the read-only config register (Jim Quinlan)
- Handle regulator_bulk_get() error to avoid panic when we call
regulator_bulk_free() later (Jim Quinlan)
- Disable regulators only when removing the bus immediately below a
Root Port because we don't support regulators deeper in the
hierarchy (Jim Quinlan)
- Make const read-only arrays static (Colin Ian King)
Cadence PCIe endpoint driver:
- Correct MSG TLP generation so endpoints can generate INTx messages
(Hans Zhang)
Freescale i.MX6 PCIe controller driver:
- Identify the second controller on i.MX8MQ based on devicetree
'linux,pci-domain' instead of DBI 'reg' address (Richard Zhu)
- Remove imx_pcie_cpu_addr_fixup() since dwc core can now derive the
ATU input address (using parent_bus_offset) from devicetree (Frank
Li)
Freescale Layerscape PCIe controller driver:
- Drop deprecated 'num-ib-windows' and 'num-ob-windows' and
unnecessary 'status' from example (Krzysztof Kozlowski)
- Correct the syscon_regmap_lookup_by_phandle_args("fsl,pcie-scfg")
arg_count to fix probe failure on LS1043A (Ioana Ciornei)
HiSilicon STB PCIe controller driver:
- Call phy_exit() to clean up if histb_pcie_probe() fails (Christophe
JAILLET)
Intel Gateway PCIe controller driver:
- Remove intel_pcie_cpu_addr() since dwc core can now derive the ATU
input address (using parent_bus_offset) from devicetree (Frank Li)
Intel VMD host bridge driver:
- Convert vmd_dev.cfg_lock from spinlock_t to raw_spinlock_t so
pci_ops.read() will never sleep, even on PREEMPT_RT where
spinlock_t becomes a sleepable lock, to avoid calling a sleeping
function from invalid context (Ryo Takakura)
MediaTek PCIe Gen3 controller driver:
- Remove leftover mac_reset assert for Airoha EN7581 SoC (Lorenzo
Bianconi)
- Add EN7581 PBUS controller 'mediatek,pbus-csr' DT property and
program host bridge memory aperture to this syscon node (Lorenzo
Bianconi)
Qualcomm PCIe controller driver:
- Add qcom,pcie-ipq5332 binding (Varadarajan Narayanan)
- Add qcom i.MX8QM and i.MX8QXP/DXP optional DMA interrupt (Alexander
Stein)
- Add optional dma-coherent DT property for Qualcomm SA8775P (Dmitry
Baryshkov)
- Make DT iommu property required for SA8775P and prohibited for
SDX55 (Dmitry Baryshkov)
- Add DT IOMMU and DMA-related properties for Qualcomm SM8450 (Dmitry
Baryshkov)
- Add endpoint DT properties for SAR2130P and enable endpoint mode in
driver (Dmitry Baryshkov)
- Describe endpoint BAR0 and BAR2 as 64-bit only and BAR1 and BAR3 as
RESERVED (Manivannan Sadhasivam)
Rockchip DesignWare PCIe controller driver:
- Describe rk3568 and rk3588 BARs as Resizable, not Fixed (Niklas
Cassel)
Synopsys DesignWare PCIe controller driver:
- Add debugfs-based Silicon Debug, Error Injection, Statistical
Counter support for DWC (Shradha Todi)
- Add debugfs property to expose LTSSM status of DWC PCIe link (Hans
Zhang)
- Add Rockchip support for DWC debugfs features (Niklas Cassel)
- Add dw_pcie_parent_bus_offset() to look up the parent bus address
of a specified 'reg' property and return the offset from the CPU
physical address (Frank Li)
- Use dw_pcie_parent_bus_offset() to derive CPU -> ATU addr offset
via 'reg[config]' for host controllers and 'reg[addr_space]' for
endpoint controllers (Frank Li)
- Apply struct dw_pcie.parent_bus_offset in ATU users to remove use
of .cpu_addr_fixup() when programming ATU (Frank Li)
TI J721E PCIe driver:
- Correct the 'link down' interrupt bit for J784S4 (Siddharth
Vadapalli)
TI Keystone PCIe controller driver:
- Describe AM65x BARs 2 and 5 as Resizable (not Fixed) and reduce
alignment requirement from 1MB to 64KB (Niklas Cassel)
Xilinx Versal CPM PCIe controller driver:
- Free IRQ domain in probe error path to avoid leaking it
(Thippeswamy Havalige)
- Add DT .compatible "xlnx,versal-cpm5nc-host" and driver support for
Versal Net CPM5NC Root Port controller (Thippeswamy Havalige)
- Add driver support for CPM5_HOST1 (Thippeswamy Havalige)
Miscellaneous:
- Convert fsl,mpc83xx-pcie binding to YAML (J. Neuschäfer)
- Use for_each_available_child_of_node_scoped() to simplify apple,
kirin, mediatek, mt7621, tegra drivers (Zhang Zekun)"
* tag 'pci-v6.15-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (197 commits)
PCI: layerscape: Fix arg_count to syscon_regmap_lookup_by_phandle_args()
PCI: j721e: Fix the value of .linkdown_irq_regfield for J784S4
misc: pci_endpoint_test: Add support for PCITEST_IRQ_TYPE_AUTO
PCI: endpoint: pci-epf-test: Expose supported IRQ types in CAPS register
PCI: dw-rockchip: Endpoint mode cannot raise INTx interrupts
PCI: endpoint: Add intx_capable to epc_features struct
dt-bindings: PCI: Add common schema for devices accessible through PCI BARs
PCI: intel-gw: Remove intel_pcie_cpu_addr()
PCI: imx6: Remove imx_pcie_cpu_addr_fixup()
PCI: dwc: Use parent_bus_offset to remove need for .cpu_addr_fixup()
PCI: dwc: ep: Ensure proper iteration over outbound map windows
PCI: dwc: ep: Use devicetree 'reg[addr_space]' to derive CPU -> ATU addr offset
PCI: dwc: ep: Consolidate devicetree handling in dw_pcie_ep_get_resources()
PCI: dwc: ep: Call epc_create() early in dw_pcie_ep_init()
PCI: dwc: Use devicetree 'reg[config]' to derive CPU -> ATU addr offset
PCI: dwc: Add dw_pcie_parent_bus_offset() checking and debug
PCI: dwc: Add dw_pcie_parent_bus_offset()
PCI/bwctrl: Fix NULL pointer dereference on bus number exhaustion
PCI: xilinx-cpm: Add cpm_csr register mapping for CPM5_HOST1 variant
PCI: brcmstb: Make const read-only arrays static
...
This reverts commit 36f5f026df, reversing
changes made to 43a7eec035.
Thomas says:
"I just noticed that for some incomprehensible reason, probably sheer
incompetemce when trying to utilize b4, I managed to merge an outdated
_and_ buggy version of that series.
Can you please revert that merge completely?"
Done.
Requested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Ioremap() msg_res region using res->start (the CPU address), not the ATU
'cpu_addr', which will be replaced with the ATU input address (which may
not be the CPU address) (Frank Li)
- Rename struct dw_pcie_ob_atu_cfg.cpu_addr to 'parent_bus_addr' (Frank Li)
- Call devm_pci_alloc_host_bridge() early in dw_pcie_host_init() to keep
devicetree-related code together (Frank Li)
- Consolidate devicetree handling in dw_pcie_host_get_resources() (Bjorn
Helgaas)
- Add dw_pcie_parent_bus_offset() to look up the parent bus address of a
specified 'reg' property and return the offset from the CPU physical
address (Frank Li)
- Add cross-checking with .cpu_addr_fixup() and debug logging to
dw_pcie_parent_bus_offset() (Frank Li)
- Use devicetree 'reg[config]' via dw_pcie_parent_bus_offset() to derive
CPU -> ATU addr offset for host controller (Frank Li)
- Call epc_create() early in dw_pcie_ep_init() to keep devicetree-related
code together (Bjorn Helgaas)
- Consolidate devicetree handling in dw_pcie_ep_get_resources() (Bjorn
Helgaas)
- Use devicetree 'reg[addr_space]' via dw_pcie_parent_bus_offset() to
derive CPU -> ATU addr offset for endpoint controller (Frank Li)
- Update dw_pcie_find_index() to remove assumption that ATU input address
is non-zero (Frank Li)
- Apply struct dw_pcie.parent_bus_offset in ATU users to remove use of
.cpu_addr_fixup() when programming ATU (Frank Li)
- Remove imx_pcie_cpu_addr_fixup() since dwc core can now derive the ATU
input address (using parent_bus_offset) from devicetree (Frank Li)
- Remove intel_pcie_cpu_addr() since dwc core can now derive the ATU input
address (using parent_bus_offset) from devicetree (Frank Li)
* pci/controller/dwc-cpu-addr-fixup:
PCI: intel-gw: Remove intel_pcie_cpu_addr()
PCI: imx6: Remove imx_pcie_cpu_addr_fixup()
PCI: dwc: Use parent_bus_offset to remove need for .cpu_addr_fixup()
PCI: dwc: ep: Ensure proper iteration over outbound map windows
PCI: dwc: ep: Use devicetree 'reg[addr_space]' to derive CPU -> ATU addr offset
PCI: dwc: ep: Consolidate devicetree handling in dw_pcie_ep_get_resources()
PCI: dwc: ep: Call epc_create() early in dw_pcie_ep_init()
PCI: dwc: Use devicetree 'reg[config]' to derive CPU -> ATU addr offset
PCI: dwc: Add dw_pcie_parent_bus_offset() checking and debug
PCI: dwc: Add dw_pcie_parent_bus_offset()
PCI: dwc: Consolidate devicetree handling in dw_pcie_host_get_resources()
PCI: dwc: Call devm_pci_alloc_host_bridge() early in dw_pcie_host_init()
PCI: dwc: Rename cpu_addr to parent_bus_addr for ATU configuration
PCI: dwc: Use resource start as ioremap() input in dw_pcie_pme_turn_off()
# Conflicts:
# drivers/pci/controller/dwc/pcie-designware.c
# drivers/pci/controller/dwc/pcie-designware.h
- Free IRQ domain in probe error path to avoid leaking it (Thippeswamy
Havalige)
- Add DT .compatible "xlnx,versal-cpm5nc-host" and driver support for
Versal Net CPM5NC Root Port controller (Thippeswamy Havalige)
- Add driver support for CPM5_HOST1 (Thippeswamy Havalige)
* pci/controller/xilinx-cpm:
PCI: xilinx-cpm: Add cpm_csr register mapping for CPM5_HOST1 variant
PCI: xilinx-cpm: Add support for Versal Net CPM5NC Root Port controller
dt-bindings: PCI: xilinx-cpm: Add compatible string for CPM5NC Versal Net host
PCI: xilinx-cpm: Fix IRQ domain leak in error path of probe
- Convert vmd_dev.cfg_lock from spinlock_t to raw_spinlock_t so
pci_ops.read() will never sleep, even on PREEMPT_RT where spinlock_t
becomes a sleepable lock (Ryo Takakura)
* pci/controller/vmd:
PCI: vmd: Make vmd_dev::cfg_lock a raw_spinlock_t type
- Describe endpoint BAR0 and BAR2 as 64-bit only and BAR1 and BAR3 as
RESERVED (Manivannan Sadhasivam)
- Add optional dma-coherent DT property for Qualcomm SA8775P (Dmitry
Baryshkov)
- Make DT iommu property required for SA8775P and prohibited for SDX55
(Dmitry Baryshkov)
- Add DT iommu and DMA-related properties for Qualcomm SM8450 (Dmitry
Baryshkov)
- Consolidate DMA vs non-DMA cases in DT (Dmitry Baryshkov)
- Add endpoint DT properties for SAR2130P and enable endpoint mode in
driver (Dmitry Baryshkov)
* pci/controller/qcom:
PCI: qcom-ep: Enable EP mode support for SAR2130P
dt-bindings: PCI: qcom-ep: Add SAR2130P compatible
dt-bindings: PCI: qcom-ep: Consolidate DMA vs non-DMA cases
dt-bindings: PCI: qcom-ep: Enable DMA for SM8450
dt-bindings: PCI: qcom-ep: Describe optional IOMMU
dt-bindings: PCI: qcom-ep: Describe optional dma-coherent property
PCI: qcom-ep: Mark BAR0/BAR2 as 64bit BARs and BAR1/BAR3 as RESERVED
- Correct the 'link down' interrupt bit for J784S4 (Siddharth Vadapalli)
* pci/controller/j721e:
PCI: j721e: Fix the value of .linkdown_irq_regfield for J784S4
- Identify the second controller on i.MX8MQ based on devicetree
'linux,pci-domain' instead of DBI 'reg' address (Richard Zhu)
- Use devm_clk_bulk_get_all() to fetch clocks to simplify the code (Richard
Zhu)
* pci/controller/imx6:
PCI: imx6: Use devm_clk_bulk_get_all() to fetch clocks
PCI: imx6: Identify controller via 'linux,pci-domain', not address
- Correct comment to say that invalidations from a PF driver are delivered
to the VF endpoint driver, not by the VF driver (Easwar Hariharan)
* pci/controller/hyperv:
PCI: hv: Correct a comment
- Call phy_exit() to clean up if histb_pcie_probe() fails (Christophe
JAILLET)
* pci/controller/histb:
PCI: histb: Fix an error handling path in histb_pcie_probe()
- Move struct dwc_pcie_vsec_id to include/linux/pcie-dwc.h, where it can be
shared by debugfs, perf, sysfs, etc (Manivannan Sadhasivam)
- Add dw_pcie_find_vsec_capability() to locate Vendor Specific Extended
Capabilities (Shradha Todi)
- Add debugfs-based Silicon Debug, Error Injection, Statistical Counter
support for DWC (Shradha Todi)
- Add debugfs property to expose LTSSM status of DWC PCIe link (Hans Zhang)
- Add Rockchip Vendor ID and Vendor Specific ID of RAS DES Capability so
the DWC debugfs features work for Rockchip as well (Niklas Cassel)
* pci/controller/dwc:
PCI: dw-rockchip: Hide broken ATS capability for RK3588 running in EP mode
PCI: dwc: ep: Add dw_pcie_ep_hide_ext_capability()
PCI: dwc: ep: Return -ENOMEM for allocation failures
PCI: dwc: Add Rockchip to the RAS DES allowed vendor list
PCI: Add Rockchip Vendor ID
PCI: dwc: Add debugfs property to provide LTSSM status of the PCIe link
PCI: dwc: Add debugfs based Statistical Counter support for DWC
PCI: dwc: Add debugfs based Error Injection support for DWC
PCI: dwc: Add debugfs based Silicon Debug support for DWC
PCI: dwc: Add helper to find the Vendor Specific Extended Capability (VSEC)
perf/dwc_pcie: Move common DWC struct definitions to 'pcie-dwc.h'
- Correct MSG TLP generation so endpoint can generate INTx messages (Hans
Zhang)
* pci/controller/cadence:
PCI: cadence-ep: Fix the driver to send MSG TLP for INTx without data payload
- Add missing of_node refcount release after of_parse_phandle() (Stanimir
Varbanov)
- Add BCM2712 MSI-X DT binding and interrupt controller drivers (Stanimir
Varbanov)
- Add brcmstb softdep on irq_bcm2712_mip MIP MSI-X interrupt controller
driver to ensure that it is loaded first (Stanimir Varbanov)
- Add struct brcm_pcie pointer to pcie_cfg_data so we can reference the
pcie_cfg_data directly instead of copying it to brcm_pcie (Stanimir
Varbanov)
- Expand inbound window map to 64GB so it can accommodate BCM2712 (Stanimir
Varbanov)
- Add BCM2712 support and DT updates (Stanimir Varbanov)
- Apply link speed restriction before bringing link up, not after (Jim
Quinlan)
- Update Max Link Speed in Link Capabilities via the internal writable
register, not the read-only config register (Jim Quinlan)
- Handle regulator_bulk_get() error to avoid panic when we call
regulator_bulk_free() later (Jim Quinlan)
- Disable regulators only when removing the bus immediately below a Root
Port because we don't support regulators deeper in the hierarchy (Jim
Quinlan)
- Consistently use config access index/data register offsets from the
SoC-specific pcie_offsets[] table (Jim Quinlan)
- Update MDIO register fields that reduced CMD from 12 bits to 1 and
widened PORT from 4 bits to 5 and split it into two parts (Jim Quinlan)
- Make const read-only arrays static (Colin Ian King)
* pci/controller/brcmstb:
PCI: brcmstb: Make const read-only arrays static
PCI: brcmstb: Make irq_domain_set_info() parameter cast explicit
PCI: brcmstb: Make two changes in MDIO register fields
PCI: brcmstb: Use same constant table for config space access
PCI: brcmstb: Fix potential premature regulator disabling
PCI: brcmstb: Fix error path after a call to regulator_bulk_get()
PCI: brcmstb: Do not assume that register field starts at LSB
PCI: brcmstb: Use internal register to change link capability
PCI: brcmstb: Set generation limit before PCIe link up
PCI: brcmstb: Add BCM2712 support
PCI: brcmstb: Expand inbound window size up to 64GB
PCI: brcmstb: Reuse pcie_cfg_data structure
PCI: brcmstb: Add a softdep to MIP MSI-X driver
irqchip: Add Broadcom BCM2712 MSI-X interrupt controller
dt-bindings: PCI: brcmstb: Update bindings for PCIe on BCM2712
dt-bindings: interrupt-controller: Add BCM2712 MSI-X bindings
PCI: brcmstb: Fix missing of_node_put() in brcm_pcie_probe()
- Add DT binding for Agilex family (P-Tile, F-Tile, R-Tile) (Matthew
Gerlach)
- Add driver support for Agilex family (P-Tile, F-Tile, R-Tile) (D M,
Sharath Kumar)
* pci/controller/altera:
PCI: altera: Add Agilex support
dt-bindings: PCI: altera: Add binding for Agilex
- Use for_each_available_child_of_node_scoped() to simplify apple, kirin,
mediatek, mt7621, tegra drivers (Zhang Zekun)
* pci/scoped-cleanup:
PCI: tegra: Use helper function for_each_child_of_node_scoped()
PCI: apple: Use helper function for_each_child_of_node_scoped()
PCI: mt7621: Use helper function for_each_available_child_of_node_scoped()
PCI: mediatek: Use helper function for_each_available_child_of_node_scoped()
PCI: kirin: Tidy up _probe() related function with dev_err_probe()
PCI: kirin: Use helper function for_each_available_child_of_node_scoped()
- Fix endpoint BAR testing so the test can skip disabled BARs instead of
reporting them as failures (Niklas Cassel)
- Verify that pci_endpoint interrupt tests set the correct IRQ type
(Kunihiko Hayashi)
- Fix interpretation of pci_endpoint_test_bars_read_bar() error returns
(Niklas Cassel)
- Fix potential string truncation in pci_endpoint_test_probe() (Niklas
Cassel)
- Increase endpoint test BAR size variable to accommodate BARs larger than
INT_MAX (Niklas Cassel)
- Release IRQs to avoid leak in pci_endpoint interrupt tests (Kunihiko
Hayashi)
- Log the correct IRQ type when pci_endpoint IRQ request test fails
(Kunihiko Hayashi)
- Remove pci_endpoint_test irq_type and no_msi globals; instead use
test->irq_type (Kunihiko Hayashi)
- Remove unnecessary use of managed IRQ functions in pci_endpoint_test
(Kunihiko Hayashi)
- Add and use IRQ_TYPE_* defines in pci_endpoint_test (Niklas Cassel)
- Add struct pci_epc_features.intx_capable and note that RK3568 and RK3588
can't raise INTx interrupts (Niklas Cassel)
- Expose supported IRQ types in CAPS so pci_endpoint_test can set
appropriate type (Niklas Cassel)
- Add PCITEST_IRQ_TYPE_AUTO to pci_endpoint_test for cases where the IRQ
type doesn't matter (Niklas Cassel)
* pci/endpoint-test:
misc: pci_endpoint_test: Add support for PCITEST_IRQ_TYPE_AUTO
PCI: endpoint: pci-epf-test: Expose supported IRQ types in CAPS register
PCI: dw-rockchip: Endpoint mode cannot raise INTx interrupts
PCI: endpoint: Add intx_capable to epc_features struct
selftests: pci_endpoint: Use IRQ_TYPE_* defines from UAPI header
misc: pci_endpoint_test: Use IRQ_TYPE_* defines from UAPI header
PCI: endpoint: pcitest: Add IRQ_TYPE_* defines to UAPI header
misc: pci_endpoint_test: Do not use managed IRQ functions
misc: pci_endpoint_test: Remove global 'irq_type' and 'no_msi'
misc: pci_endpoint_test: Fix 'irq_type' to convey the correct type
misc: pci_endpoint_test: Fix displaying 'irq_type' after 'request_irq' error
misc: pci_endpoint_test: Avoid issue of interrupts remaining after request_irq error
misc: pci_endpoint_test: Handle BAR sizes larger than INT_MAX
misc: pci_endpoint_test: Give disabled BARs a distinct error code
misc: pci_endpoint_test: Fix potential truncation in pci_endpoint_test_probe()
misc: pci_endpoint_test: Fix pci_endpoint_test_bars_read_bar() error handling
selftests: pci_endpoint: Add GET_IRQTYPE checks to each interrupt test
selftests: pci_endpoint: Skip disabled BARs
The arg_count parameter to syscon_regmap_lookup_by_phandle_args()
represents the number of argument cells following the phandle. In this
case, the number of arguments should be 1 instead of 2 since the dt
property looks like this:
fsl,pcie-scfg = <&scfg 0>;
Without this fix, layerscape-pcie fails with the following message on
LS1043A:
OF: /soc/pcie@3500000: phandle scfg@1570000 needs 2, found 1
layerscape-pcie 3500000.pcie: No syscfg phandle specified
layerscape-pcie 3500000.pcie: probe with driver layerscape-pcie failed with error -22
Link: https://lore.kernel.org/r/20250327151949.2765193-1-ioana.ciornei@nxp.com
Fixes: 149fc35734 ("PCI: layerscape: Use syscon_regmap_lookup_by_phandle_args")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Roy Zang <Roy.Zang@nxp.com>
Cc: stable@vger.kernel.org
Commit e49ad66781 ("PCI: j721e: Add TI J784S4 PCIe configuration")
assigned the value of .linkdown_irq_regfield for the J784S4 SoC as the
"LINK_DOWN" macro corresponding to BIT(1), and as a result, the Link
Down interrupts on J784S4 SoC are missed.
According to the Technical Reference Manual and Register Documentation
for the J784S4 SoC[1], BIT(1) corresponds to "ENABLE_SYS_EN_PCIE_DPA_1",
which is not the correct field for the link-state interrupt. Instead, it
is BIT(10) of the "PCIE_INTD_ENABLE_REG_SYS_2" register that corresponds
to the link-state field named as "ENABLE_SYS_EN_PCIE_LINK_STATE".
Thus, set .linkdown_irq_regfield to the macro "J7200_LINK_DOWN", which
expands to BIT(10) and was first defined for the J7200 SoC. Other SoCs
already reuse this macro since it accurately represents the "link-state"
field in their respective "PCIE_INTD_ENABLE_REG_SYS_2" register.
1: https://www.ti.com/lit/zip/spruj52
Fixes: e49ad66781 ("PCI: j721e: Add TI J784S4 PCIe configuration")
Cc: stable@vger.kernel.org
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
[kwilczynski: commit log, add a missing .linkdown_irq_regfield member
set to the J7200_LINK_DOWN macro to struct j7200_pcie_ep_data]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Link: https://lore.kernel.org/r/20250305132018.2260771-1-s-vadapalli@ti.com
Neither RK3568 or RK3588 supports INTx interrupts.
Since epc_features is zero initialized, this is strictly not needed.
However, setting intx_capable explicitly to false makes it more clear
that neither RK3568 or RK3588 supports INTx interrupts.
No functional change.
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Link: https://lore.kernel.org/r/20250310111016.859445-14-cassel@kernel.org
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRTLbB6QfY48x44uB6AXGG7T9hjvgUCZ9/gEwAKCRCAXGG7T9hj
vlxhAQCRzSCNI8wwvENnuc2OnRyWKy8gq7C5WAOIOJdJ3U+scQEAwKGhPJLwE4IS
/JDh5PRJgZ4rdMYatuDfldEcSAfRRgw=
=dF6Z
-----END PGP SIGNATURE-----
Merge tag 'for-linus-6.15-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen updates from Juergen Gross:
- cleanup: remove an used function
- add support for a XenServer specific virtual PCI device
- fix the handling of a sparse Xen hypervisor symbol table
- avoid warnings when building the kernel with gcc 15
- fix use of devices behind a VMD bridge when running as a Xen PV dom0
* tag 'for-linus-6.15-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
PCI/MSI: Convert pci_msi_ignore_mask to per MSI domain flag
PCI: vmd: Disable MSI remapping bypass under Xen
xen/pci: Do not register devices with segments >= 0x10000
xen/pciback: Remove unused pcistub_get_pci_dev
xenfs/xensyms: respect hypervisor's "next" indication
xen/mcelog: Add __nonstring annotations for unterminated strings
xen: Add support for XenServer 6.1 platform device
- Switch the MSI descriptor locking to guards
- Replace the broken PCI/TPH implementation, which lacks any form of
serialization against concurrent modifications with a properly
serialized mechanism in the PCI/MSI core code.
- Replace the MSI descriptor abuse in the SCSI/UFS Qualcom driver with
dedicated driver internal storage.
-----BEGIN PGP SIGNATURE-----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=Vl8Q
-----END PGP SIGNATURE-----
Merge tag 'irq-msi-2025-03-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull MSI irq updates from Thomas Gleixner:
- Switch the MSI descriptor locking to guards
- Replace the broken PCI/TPH implementation, which lacks any form of
serialization against concurrent modifications with a properly
serialized mechanism in the PCI/MSI core code
- Replace the MSI descriptor abuse in the SCSI/UFS Qualcom driver with
dedicated driver internal storage
* tag 'irq-msi-2025-03-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq/msi: Rename msi_[un]lock_descs()
scsi: ufs: qcom: Remove the MSI descriptor abuse
PCI/TPH: Replace the broken MSI-X control word update
PCI/MSI: Provide a sane mechanism for TPH
PCI: hv: Switch MSI descriptor locking to guard()
PCI/MSI: Switch to MSI descriptor locking to guard()
NTB/msi: Switch MSI descriptor locking to lock guard()
soc: ti: ti_sci_inta_msi: Switch MSI descriptor locking to guard()
genirq/msi: Use lock guards for MSI descriptor locking
cleanup: Provide retain_ptr()
genirq/msi: Make a few functions static
Remove imx_pcie_cpu_addr_fixup, the .cpu_addr_fixup() method, because the
dwc core driver already handles address translation based on the devicetree
description.
Link: https://lore.kernel.org/r/20250315201548.858189-14-helgaas@kernel.org
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Richard Zhu <hongxing.zhu@nxp.com>
We know the parent_bus_offset, either computed from a DT reg property (the
offset is the CPU physical addr - the 'config'/'addr_space' address on the
parent bus) or from a .cpu_addr_fixup() (which may have used a host bridge
window offset).
Apply that parent_bus_offset instead of calling .cpu_addr_fixup() when
programming the ATU.
This assumes all intermediate addresses are at the same offset from the CPU
physical addresses.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20250315201548.858189-13-helgaas@kernel.org
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Most systems' PCIe outbound map windows have non-zero physical addresses,
but the possibility of encountering zero increased after following commit
("PCI: dwc: Use parent_bus_offset").
'ep->outbound_addr[n]', representing 'parent_bus_address', might be 0 on
some hardware, which trims high address bits through bus fabric before
sending to the PCIe controller.
Replace the iteration logic with 'for_each_set_bit()' to ensure only
allocated map windows are iterated when determining the ATU index from a
given address.
Link: https://lore.kernel.org/r/20250315201548.858189-12-helgaas@kernel.org
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Endpoint
┌───────────────────────────────────────────────┐
│ pcie-ep@5f010000 │
│ ┌────────────────┐│
│ │ Endpoint ││
│ │ PCIe ││
│ │ Controller ││
│ bus@5f000000 │ ┌────────►
│ ┌──────────┐ │ │ ││dynamically
│ │ │ Outbound Transfer │ ││allocated
│┌─────┐ │ Bus ┼─────►│ ATU ───────┘ ││PCI Addr
││ │ │ Fabric │Bus │ ││
││ CPU ├───►│ │Addr │ ││
││ │CPU │ │0x8000_0000 ││
│└─────┘Addr└──────────┘ │ ││
│ 0x7000_0000 └────────────────┘│
└───────────────────────────────────────────────┘
bus@5f000000 {
compatible = "simple-bus";
ranges = <0x80000000 0x0 0x70000000 0x10000000>;
pcie-ep@5f010000 {
reg = <0x80000000 0x10000000>;
reg-names ="addr_space";
...
};
...
};
In the diagram above, CPU writes data to outbound window address
0x7000_0000, and the bus fabric maps it to 0x8000_0000. The ATU uses
bus address 0x8000_0000 as input address and maps to some PCI address
dynamically allocated by a PCI device driver on the host side.
The pcie-ep@5f010000 'reg[addr_space]' is the parent bus address, which is
the input of PCIe controller, including the ATU.
Set parent_bus_offset, the offset from the CPU address to the PCIe
controller input address using dw_pcie_init_parent_bus_offset(). The
parent_bus_offset is not used yet, so no functional change intended.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20250315201548.858189-11-helgaas@kernel.org
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Move devm_pci_epc_create() to the beginning of dw_pcie_ep_init().
devm_pci_epc_create() is generic code that doesn't depend on any DWC
resource, so moving it earlier keeps all the subsequent devicetree-related
code together.
Link: https://lore.kernel.org/r/20250315201548.858189-9-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
The 'ranges' property of a PCI controller's parent can indicate address
translation information. Most system use 1:1 map between CPU physical and
PCI controller input addresses.
But some hardware, like i.MX8QXP, doesn't use 1:1 map. See below diagram:
┌─────────┐ ┌────────────┐
┌─────┐ │ │ IA: 0x8ff8_0000 │ │
│ CPU ├───►│ ┌────►├─────────────────┐ │ PCI │
└─────┘ │ │ │ IA: 0x8ff0_0000 │ │ │
CPU Addr │ │ ┌─►├─────────────┐ │ │ Controller │
0x7ff8_0000─┼───┘ │ │ │ │ │ │
│ │ │ │ │ │ │ PCI Addr
0x7ff0_0000─┼──────┘ │ │ └──► IOSpace ─┼────────────►
│ │ │ │ │ 0
0x7000_0000─┼────────►├─────────┐ │ │ │
└─────────┘ │ └──────► CfgSpace ─┼────────────►
Bus Fabric │ │ │ 0
│ │ │
└──────────► MemSpace ─┼────────────►
IA: 0x8000_0000 │ │ 0x8000_0000
└────────────┘
bus@5f000000 {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
ranges = <0x80000000 0x0 0x70000000 0x10000000>;
pcie@5f010000 {
compatible = "fsl,imx8q-pcie";
reg = <0x5f010000 0x10000>, <0x8ff00000 0x80000>;
reg-names = "dbi", "config";
...
};
};
Intermediate address (IA) here means the PCIe controller input address.
The pcie@5f010000 'reg[config]' address is the parent bus (PCIe controller
input) address of CfgSpace.
The ATU in MemSpace is not explicitly described via devicetree, so we
assume the offset from CPU address to intermediate MemSpace address is the
same as that for CfgSpace.
We could use bus@5f000000 'ranges' for the same purpose.
Set parent_bus_offset using dw_pcie_init_parent_bus_offset(). The
parent_bus_offset is not used yet, so no functional change intended.
Link: https://lore.kernel.org/r/20250315201548.858189-8-helgaas@kernel.org
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
dw_pcie_parent_bus_offset() looks up the parent bus address of a PCI
controller 'reg' property in devicetree. If implemented, .cpu_addr_fixup()
is a hard-coded way to get the parent bus address corresponding to a CPU
physical address.
Add debug code to compare the address from .cpu_addr_fixup() with the
address from devicetree. If they match, warn that .cpu_addr_fixup() is
redundant and should be removed; if they differ, warn that something is
wrong with the devicetree.
If .cpu_addr_fixup() is not implemented, the parent bus address should be
identical to the CPU physical address because we previously ignored the
parent bus address from devicetree. If the devicetree has a different
parent bus address, warn about it being broken.
[bhelgaas: split debug to separate patch for easier future revert, commit
log]
Link: https://lore.kernel.org/r/20250315201548.858189-7-helgaas@kernel.org
Signed-off-by: Frank Li <Frank.Li@nxp.com>
[bhelgaas: squash Ioana Ciornei <ioana.ciornei@nxp.com> fix for NULL
pointer deref when driver doesn't supply dw_pcie_ops, e.g., layerscape-pcie
https://lore.kernel.org/r/20250319134339.3114817-1-ioana.ciornei@nxp.com]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Return the offset from CPU physical address to the parent bus address of
the specified element of the devicetree 'reg' property.
[bhelgaas: cpu_phy_addr -> cpu_phys_addr, return offset, split
.cpu_addr_fixup() checking and debug to separate patch]
Link: https://lore.kernel.org/r/20250315201548.858189-6-helgaas@kernel.org
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Update the CPM5 check to include CPM5_HOST1 variant. Previously, only
CPM5 was considered when mapping the "cpm_csr" register.
With this change, CPM5_HOST1 is also supported, ensuring proper
resource mapping for this variant.
Signed-off-by: Thippeswamy Havalige <thippeswamy.havalige@amd.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Link: https://lore.kernel.org/r/20250317124136.1317723-1-thippeswamy.havalige@amd.com
Don't populate the const read-only arrays "data" and "regs" on the
stack at run time, instead make them static.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
[kwilczynski: commit log, wrap overly long line to 80 columns]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Link: https://lore.kernel.org/r/20250317143456.477901-1-colin.i.king@gmail.com
Add support for AMD MDB (Multimedia DMA Bridge) IP core as Root Port.
The Versal2 devices include MDB Module. The integrated block for MDB
along with the integrated bridge can function as PCIe Root Port
controller at Gen5 32-GT/s operation per lane.
Bridge supports error and INTx interrupts and are handled using platform
specific interrupt line in Versal2.
Signed-off-by: Thippeswamy Havalige <thippeswamy.havalige@amd.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250228093351.923615-4-thippeswamy.havalige@amd.com
[bhelgaas: only present on ARM64-based SoCs; squash Kconfig dependency on
ARM64 from Geert Uytterhoeven <geert+renesas@glider.be>:
https://lore.kernel.org/r/eaef1dea7edcf146aa377d5e5c5c85a76ff56bae.1742306383.git.geert+renesas@glider.be]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
[kwilczynski: commit log, code comments and error messages clean-up,
drop redundant "depends on PCI" from Kconfig, expose the error code
as part of error messages where appropriatie, change "depends on"
expression to match existing style from other drivers]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
MSI remapping bypass (directly configuring MSI entries for devices on the
VMD bus) won't work under Xen, as Xen is not aware of devices in such bus,
and hence cannot configure the entries using the pIRQ interface in the PV
case, and in the PVH case traps won't be setup for MSI entries for such
devices.
Until Xen is aware of devices in the VMD bus prevent the
VMD_FEAT_CAN_BYPASS_MSI_REMAP capability from being used when running as
any kind of Xen guest.
The MSI remapping bypass is an optional feature of VMD bridges, and hence
when running under Xen it will be masked and devices will be forced to
redirect its interrupts from the VMD bridge. That mode of operation must
always be supported by VMD bridges and works when Xen is not aware of
devices behind the VMD bridge.
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Message-ID: <20250219092059.90850-3-roger.pau@citrix.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
The access to the PCI config space via pci_ops::read and pci_ops::write is
a low-level hardware access. The functions can be accessed with disabled
interrupts even on PREEMPT_RT. The pci_lock is a raw_spinlock_t for this
purpose.
A spinlock_t becomes a sleeping lock on PREEMPT_RT, so it cannot be
acquired with disabled interrupts. The vmd_dev::cfg_lock is accessed in
the same context as the pci_lock.
Make vmd_dev::cfg_lock a raw_spinlock_t type so it can be used with
interrupts disabled.
This was reported as:
BUG: sleeping function called from invalid context at kernel/locking/spinlock_rt.c:48
Call Trace:
rt_spin_lock+0x4e/0x130
vmd_pci_read+0x8d/0x100 [vmd]
pci_user_read_config_byte+0x6f/0xe0
pci_read_config+0xfe/0x290
sysfs_kf_bin_read+0x68/0x90
Signed-off-by: Ryo Takakura <ryotkkr98@gmail.com>
Tested-by: Luis Claudio R. Goncalves <lgoncalv@redhat.com>
Acked-by: Luis Claudio R. Goncalves <lgoncalv@redhat.com>
[bigeasy: reword commit message]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-off-by: Luis Claudio R. Goncalves <lgoncalv@redhat.com>
Link: https://lore.kernel.org/r/20250218080830.ufw3IgyX@linutronix.de
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: add back report info from
https://lore.kernel.org/lkml/20241218115951.83062-1-ryotkkr98@gmail.com/]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Move devm_pci_alloc_host_bridge() to the beginning of dw_pcie_host_init().
devm_pci_alloc_host_bridge() is generic code that doesn't depend on any DWC
resource, so moving it earlier keeps all the subsequent devicetree-related
code together.
[bhelgaas: reorder earlier in series]
Link: https://lore.kernel.org/r/20250315201548.858189-4-helgaas@kernel.org
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Rename 'cpu_addr' to 'parent_bus_addr' in the DesignWare ATU configuration.
The ATU translates parent bus addresses to PCI addresses, which are often
the same as CPU addresses but can differ in systems where the bus fabric
translates addresses before passing them to the PCIe controller. This
renaming clarifies the purpose and avoids confusion.
Link: https://lore.kernel.org/r/20250315201548.858189-3-helgaas@kernel.org
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The msg_res region translates writes into PCIe Message TLPs. Previously we
mapped this region using atu.cpu_addr, the input address programmed into
the ATU.
"cpu_addr" is a misnomer because when a bus fabric translates addresses
between the CPU and the ATU, the ATU input address is different from the
CPU address. A future patch will rename "cpu_addr" and correct the value
to be the ATU input address instead of the CPU physical address.
Map the msg_res region before writing to it using the msg_res resource
start, a CPU physical address.
Link: https://lore.kernel.org/r/20250315201548.858189-2-helgaas@kernel.org
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use devm_clk_bulk_get_all() helper to simplify clock handle code.
No functional changes intended.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
[kwilczynski: commit log, refactor to use dev_err_probe()]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20250226025628.1681206-1-hongxing.zhu@nxp.com
Instead of testing the controller register address to distinguish
controller 1 from controller 0 on i.MX8MQ platforms, use the PCI domain
number, which comes from the devicetree 'linux,pci-domain' property.
All relevant devicetrees should already supply 'linux,pci-domain', which
was added by c0b70f05c8 ("arm64: dts: imx8mq: use_dt_domains for pci
node").
Instead of being set directly in imx_pcie_probe(), pci->dbi_base will be
set by the DWC core in dw_pcie_get_resources().
No functional changes intended.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250226024256.1678103-3-hongxing.zhu@nxp.com
When running the RK3588 in Endpoint mode, with an Intel host with IOMMU
enabled, the host side prints:
DMAR: VT-d detected Invalidation Time-out Error: SID 0
When running the RK3588 in Endpoint mode, with an AMD host with IOMMU
enabled, the host side prints:
iommu ivhd0: AMD-Vi: Event logged [IOTLB_INV_TIMEOUT device=63:00.0 address=0x42b5b01a0]
Rockchip has confirmed that the ATS support for RK3588 only works when
running the PCIe controller in Root Complex (RC) mode, see:
https://lore.kernel.org/linux-pci/93cdce39-1ae6-4939-a3fc-db10be7564e5@rock-chips.com
Usually, to handle these issues, we add a quirk for the PCI vendor and
device ID in drivers/pci/quirks.c with quirk_no_ats(). That is because
we cannot usually modify the capabilities on the EP side. In this case,
we can modify the capabilities on the EP side.
Thus, hide the broken ATS capability on RK3588 when running in EP mode.
That way, we don't need any quirk on the host side, and we see no errors
on the host side, and we can run pci_endpoint_test successfully, with
the IOMMU enabled on the host side.
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
[kwilczynski: commit log, tidy up code comments and error message]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250310094826.842681-6-cassel@kernel.org
Add dw_pcie_ep_hide_ext_capability() which can be used by an endpoint
controller driver to hide a capability.
This can be useful to hide a capability that is buggy, such that the
host side does not try to enable the buggy capability.
Suggested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Link: https://lore.kernel.org/r/20250310094826.842681-5-cassel@kernel.org
If the bitmap or memory allocations fail, then dw_pcie_ep_init_registers()
will incorrectly return a success.
Return -ENOMEM instead.
Fixes: 869bc52534 ("PCI: dwc: ep: Fix DBI access failure for drivers requiring refclk from host")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/36dcb6fc-f292-4dd5-bd45-a8c6f9dc3df7@stanley.mountain
Convert the code to use the new guard(msi_descs_lock).
No functional change intended.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Acked-by: Wei Liu <wei.liu@kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/all/20250313130321.758905320@linutronix.de
The Versal Net ACAP (Adaptive Compute Acceleration Platform) devices
incorporate the Coherency and PCIe Gen5 Module, specifically the
Next-Generation Compact Module (CPM5NC).
The integrated CPM5NC block, along with the built-in bridge, can function
as a PCIe Root Port and supports the PCIe Gen5 protocol with data transfer
rates of up to 32 GT/s, and is capable of supporting up to a x16 lane-width
configuration.
Bridge errors are managed using a specific interrupt line designed for
CPM5N. The INTx interrupt support is not available.
Currently in this commit platform specific bridge errors support is not
added.
Signed-off-by: Thippeswamy Havalige <thippeswamy.havalige@amd.com>
[kwilczynski: commit log, squashed patch to fix an if-statement condition
to ensure that xilinx_cpm_pcie_init_port() does not run on the CPM5NC_HOST
variant from https://lore.kernel.org/linux-pci/20250311072402.1049990-1-thippeswamy.havalige@amd.com]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250224155025.782179-4-thippeswamy.havalige@amd.com
The IRQ domain allocated for the PCIe controller is not freed if
resource_list_first_type() returns NULL, leading to a resource leak.
This fix ensures properly cleaning up the allocated IRQ domain in
the error path.
Fixes: 49e427e6bd ("Merge branch 'pci/host-probe-refactor'")
Signed-off-by: Thippeswamy Havalige <thippeswamy.havalige@amd.com>
[kwilczynski: added missing Fixes: tag, refactored to use one of the goto labels]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Link: https://lore.kernel.org/r/20250224155025.782179-2-thippeswamy.havalige@amd.com
Remove the superfluous function dw_pcie_ep_find_ext_capability(),
as it is virtually identical to dw_pcie_find_ext_capability().
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250221202646.395252-3-cassel@kernel.org
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Looking at section "11.4.4.29 USP_PCIE_RESBAR Registers Summary" in the
Technical Reference Manual (TRM) for RK3588, we can see that none of the
BARs are Fixed BARs, but actually Resizable BARs.
I couldn't find any reference in the TRM for RK3568, but looking at the
downstream PCIe endpoint driver, both RK3568 and RK3588 are treated as
the same, so the BARs on RK3568 must also be Resizable BARs.
Now when we actually have support for Resizable BARs, let's configure
these BARs as such.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Link: https://lore.kernel.org/r/20250131182949.465530-16-cassel@kernel.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The support for a specific iATU alignment was added in
commit 2a9a801620 ("PCI: endpoint: Add support to specify alignment for
buffers allocated to BARs").
This commit specifically mentions both that the alignment by each DWC
based EP driver should match CX_ATU_MIN_REGION_SIZE, and that AM65x
specifically has a 64 KB alignment.
This also matches the CX_ATU_MIN_REGION_SIZE value specified in the
section "12.2.2.4.7 PCIe Subsystem Address Translation" of the Technical
Reference Manual (TRM) for AM65x:
https://www.ti.com/lit/ug/spruid7e/spruid7e.pdf
This higher value, 1 MB, was obviously an ugly hack used to be able to
handle Resizable BARs which have a minimum size of 1 MB.
Now when we actually have support for Resizable BARs, let's configure the
iATU alignment requirement to the actual requirement.
(BARs described as Resizable will still get aligned to 1 MB.)
Cc: stable+noautosel@kernel.org # Depends on PCI endpoint Resizable BARs series
Fixes: 23284ad677 ("PCI: keystone: Add support for PCIe EP in AM654x Platforms")
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250131182949.465530-15-cassel@kernel.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Looking at section "12.2.2.4.15 PCIe Subsystem BAR Configuration" in the
following Technical Reference Manual (TRM) for AM65x:
https://www.ti.com/lit/ug/spruid7e/spruid7e.pdf
We can see that BAR2 and BAR5 are not Fixed BARs, but actually Resizable
BARs.
Now when we actually have support for Resizable BARs, let's configure
these BARs as such.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Link: https://lore.kernel.org/r/20250131182949.465530-14-cassel@kernel.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The DWC databook specifies three different BARn_SIZING_SCHEME_N as:
- Fixed Mask (0)
- Programmable Mask (1)
- Resizable BAR (2)
Each of these sizing schemes have different instructions for how to
initialize the BAR.
The DWC driver currently does not support resizable BARs.
Instead, in order to somewhat support resizable BARs, the DWC EP driver
currently has an ugly hack that force sets a resizable BAR to 1 MB, if
such a BAR is detected.
Additionally, this hack only works if the DWC glue driver also has lied
in their EPC features, and claimed that the resizable BAR is a 1 MB fixed
size BAR.
This is unintuitive (as you somehow need to know that you need to lie in
your EPC features), but other than that it is overly restrictive, since a
resizable BAR is capable of supporting sizes different than 1 MB.
Add proper support for resizable BARs in the DWC EP driver.
Note that the pci_epc_set_bar() API takes a struct pci_epf_bar which tells
the EPC driver how it wants to configure the BAR.
struct pci_epf_bar only has a single size struct member.
This means that an EPC driver will only be able to set a single supported
size. This is perfectly fine, as we do not need the complexity of allowing
a host to change the size of the BAR. If someone ever wants to support
resizing a resizable BAR, the pci_epc_set_bar() API can be extended in the
future.
With these changes, we allow an EPF driver to configure the size of
Resizable BARs, rather than forcing them to a 1 MB size.
This means that an EPC driver does not need to lie in EPC features, and an
EPF driver will be able to set an arbitrary size (not be forced to a 1 MB
size), just like BAR_PROGRAMMABLE.
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250131182949.465530-13-cassel@kernel.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Move dw_pcie_ep_find_ext_capability() so that it is located next to
dw_pcie_ep_find_capability().
Additionally, a follow-up commit requires this to be defined earlier
in order to avoid a forward declaration.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Link: https://lore.kernel.org/r/20250131182949.465530-12-cassel@kernel.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Add PCIe Root Port controller support for the Agilex family of chips.
The Agilex PCIe Hard IP has three variants that are mostly software
compatible, except for a couple register offsets. The P-Tile variant
supports Gen3/Gen4 1x16. The F-Tile variant supports Gen3/Gen4 4x4,
4x8, and 4x16. The R-Tile variant improves on the F-Tile variant by
adding Gen5 support.
To simplify the implementation of pci_ops read/write functions,
ep_{read/write}_cfg() callbacks were added to struct altera_pci_ops
to easily distinguish between hardware variants.
Signed-off-by: D M, Sharath Kumar <sharath.kumar.d.m@intel.com>
Signed-off-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250221170452.875419-3-matthew.gerlach@linux.intel.com
[kwilczynski: tidy code comments]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The for_each_available_child_of_node_scoped() helper provides
a scope-based clean-up functionality to put the device_node
automatically, and as such, there is no need to call of_node_put()
directly.
Thus, use this helper to simplify the code.
Signed-off-by: Zhang Zekun <zhangzekun11@huawei.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240831040413.126417-7-zhangzekun11@huawei.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The for_each_available_child_of_node_scoped() helper provides
a scope-based clean-up functionality to put the device_node
automatically, and as such, there is no need to call of_node_put()
directly.
Thus, use this helper to simplify the code.
Signed-off-by: Zhang Zekun <zhangzekun11@huawei.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240831040413.126417-6-zhangzekun11@huawei.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The for_each_available_child_of_node_scoped() helper provides
a scope-based clean-up functionality to put the device_node
automatically, and as such, there is no need to call of_node_put()
directly.
Thus, use this helper to simplify the code.
Signed-off-by: Zhang Zekun <zhangzekun11@huawei.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240831040413.126417-5-zhangzekun11@huawei.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The for_each_available_child_of_node_scoped() helper provides
a scope-based clean-up functionality to put the device_node
automatically, and as such, there is no need to call of_node_put()
directly.
Thus, use this helper to simplify the code.
Signed-off-by: Zhang Zekun <zhangzekun11@huawei.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240831040413.126417-4-zhangzekun11@huawei.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The combination of dev_err() and the returned error code could be
replaced by dev_err_probe() in driver's probe function.
Thus, convert the code to use dev_err_probe() to make code simpler.
Suggested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Zhang Zekun <zhangzekun11@huawei.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20240831040413.126417-3-zhangzekun11@huawei.com
[kwilczynski: commit log, return -ETIMEDOUT from hi3660_pcie_phy_start()
rather than -EINVAL for when the PIPE clock fails to become stable,
drop redundant dev->of_node NULL check]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Move PCI_VENDOR_ID_ROCKCHIP from pci_endpoint_test.c to pci_ids.h and
reuse it in pcie-rockchip-host.c.
Link: https://lore.kernel.org/r/20250218092120.2322784-2-cassel@kernel.org
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Add the debugfs property to provide a view of the current link's LTSSM
status from the Root Port device.
Signed-off-by: Hans Zhang <18255117159@163.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Tested-by: Niklas Cassel <cassel@kernel.org>
Tested-by: Hrishikesh Deleep <hrishikesh.d@samsung.com>
Link: https://lore.kernel.org/r/20250223141848.231232-1-18255117159@163.com
[kwilczynski: commit log, refactor dw_ltssm_sts_string() to avoid
compilation errors on platforms that do not set CONFIG_PCIE_DW_HOST]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Add support to provide Statistical Counter interface to userspace.
This set of debug registers are part of the RAS DES feature present in
DesignWare PCIe controllers.
Co-developed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Shradha Todi <shradha.t@samsung.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Tested-by: Hrishikesh Deleep <hrishikesh.d@samsung.com>
Link: https://lore.kernel.org/r/20250221131548.59616-6-shradha.t@samsung.com
[kwilczynski: commit log, tidy up code comments, update documentation,
squashed patch that checks if the event counter is supported from
https://lore.kernel.org/linux-pci/20250225171239.19574-3-manivannan.sadhasivam@linaro.org]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Add support to provide Error Injection interface to userspace.
This set of debug registers are part of the RAS DES feature present in
DesignWare PCIe controllers.
Signed-off-by: Shradha Todi <shradha.t@samsung.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Tested-by: Hrishikesh Deleep <hrishikesh.d@samsung.com>
Link: https://lore.kernel.org/r/20250221131548.59616-5-shradha.t@samsung.com
[kwilczynski: commit log, tidy up code comments, update documentation,
change debugfs property name from "duplicate_dllp" to "duplicate_tlp"]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Add support to provide Silicon Debug interface to userspace.
This set of debug registers are part of the RAS DES feature present in
DesignWare PCIe controllers.
Co-developed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Shradha Todi <shradha.t@samsung.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Tested-by: Hrishikesh Deleep <hrishikesh.d@samsung.com>
Link: https://lore.kernel.org/r/20250221131548.59616-4-shradha.t@samsung.com
[kwilczynski: commit log, tidy up Kconfig and drop "default y", tidy up
code comments, squashed patch that fixes a NULL pointer dereference when
debugfs is already unavailable during clean-up from
https://lore.kernel.org/linux-pci/20250225171239.19574-2-manivannan.sadhasivam@linaro.org,
refactor dwc_pcie_debugfs_init() to not return errors, squashed patch that
changes how lack of the RAS DES capability is handled from
https://lore.kernel.org/linux-pci/20250304151814.6xu7cbpwpqrvcad5@thinkpad]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Fix the following inconsistent indentation warning:
drivers/pci/controller/pcie-mediatek-gen3.c:922 mtk_pcie_parse_port() warn: inconsistent indenting
Found using Smatch. No functional changes intended.
Signed-off-by: Charles Han <hanchunchao@inspur.com>
Link: https://lore.kernel.org/r/20250305070022.4668-1-hanchunchao@inspur.com
[kwilczynski: commit log, refactor if-statement around num_lanes to
make it more readable, wrap overly long lines to fit 80 colums]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The for_each_available_child_of_node_scoped() helper provides
a scope-based clean-up functionality to put the device_node
automatically, and as such, there is no need to call of_node_put()
directly.
Thus, use this helper to simplify the code.
Signed-off-by: Zhang Zekun <zhangzekun11@huawei.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240831040413.126417-2-zhangzekun11@huawei.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Make the cast to the irq_hw_number_t type for the parameter passed to
irq_domain_set_info() function explicit.
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250214173944.47506-9-james.quinlan@broadcom.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The hardware has been updated with two changes to the MDIO packet
format.
The CMD field used to be 12 bits and now is only 1 bit. This change
is backwards compatible because the field's starting bit position is
unchanged, and the only commands we've used have values 0 and 1.
The PORT field's width has been changed from 4 bits to 5 bits. When
written, the new bit is not contiguous with the other four. However,
this change is backwards compatible because the driver never used
anything other than 0 for the port field's value.
Thus, update the existing code to handle new changes to the hardware
in a backwards-compatible manner.
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250214173944.47506-8-james.quinlan@broadcom.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The constants EXT_CFG_DATA and EXT_CFG_INDEX vary by SoC, where one of
the map_bus methods used these constants, and the other used a different
set of constants.
Thankfully, there was no problem because the SoCs that used the latter
map_bus method all had the same register constants.
Thus, remove redundant constants and adjust the code to use the correct
constants accordingly.
While at it, update the value of EXT_CFG_DATA to use the 4k-page based
configuration space access system, which is what the second map_bus
method was already using.
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20250214173944.47506-7-james.quinlan@broadcom.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The platform supports enabling and disabling regulators only on
ports below the Root Complex.
Thus, we need to verify this both when adding and removing the bus,
otherwise regulators may be disabled prematurely when a bus further
down the topology is removed.
Fixes: 9e6be018b2 ("PCI: brcmstb: Enable child bus device regulators from DT")
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250214173944.47506-6-james.quinlan@broadcom.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
If the regulator_bulk_get() returns an error and no regulators
are created, we need to set their number to zero.
If we don't do this and the PCIe link up fails, a call to the
regulator_bulk_free() will result in a kernel panic.
While at it, print the error value, as we cannot return an error
upwards as the kernel will WARN() on an error from add_bus().
Fixes: 9e6be018b2 ("PCI: brcmstb: Enable child bus device regulators from DT")
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20250214173944.47506-5-james.quinlan@broadcom.com
[kwilczynski: commit log, use comma in the message to match style with
other similar messages]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
When setting the LNKCAP and LNKCTL2 register fields, it was assumed
that the field started at the LSB of the register.
Although the masks do indeed start at the LSB, and this will probably
not change, it is prudent to use a method that makes no assumption
about the mask's placement in the register.
Thus, use the u{16,32}p_replace_bits() helpers since they are already
wildly used in this driver.
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250214173944.47506-4-james.quinlan@broadcom.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The driver has been mistakenly writing to a read-only (RO)
configuration space register (PCI_EXP_LNKCAP) to change the
PCIe link capability.
Although harmless in this case, the proper write destination
is an internal register that is reflected by PCI_EXP_LNKCAP.
Thus, fix the brcm_pcie_set_gen() function to correctly update
the link capability.
Fixes: c045213703 ("PCI: brcmstb: Add Broadcom STB PCIe host controller driver")
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250214173944.47506-3-james.quinlan@broadcom.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
When the user elects to limit the PCIe generation via the appropriate
devicetree property, apply the settings before the PCIe link up, not
after.
Fixes: c045213703 ("PCI: brcmstb: Add Broadcom STB PCIe host controller driver")
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250214173944.47506-2-james.quinlan@broadcom.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Add a bare minimum amount of changes in order to support PCIe Root
Complex hardware IP found on RPi5. The PCIe controller on BCM2712
is based on BCM7712 and as such it inherits register offsets, PERST#
assertion, bridge_reset ops, and inbound windows count.
Although, the implementation for BCM2712 needs a workaround related to
the control of the bridge_reset where turning off of the Root Port must
not shutdown the bridge_reset and this must be avoided. To implement
this workaround a quirks field is introduced in pcie_cfg_data struct.
The controller also needs adjustment of PHY PLL setup to use a 54MHz
input refclk. The default input reference clock for the PHY PLL is
100Mhz, except for some devices where it is 54Mhz like BCM2712C1 and
BCM2712D0.
To implement those adjustments introduce a new .post_setup op in
pcie_cfg_data and call it at the end of brcm_pcie_setup function.
The BCM2712 .post_setup callback implements the required MDIO writes
that switch the PLL refclk and also change PHY PM clock period.
Without this RPi5 PCIex1 is unable to enumerate endpoint devices on
the expansion connector.
Signed-off-by: Stanimir Varbanov <svarbanov@suse.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Jim Quinlan <james.quinlan@broadcom.com>
Tested-by: Ivan T. Ivanov <iivanov@suse.de>
Link: https://lore.kernel.org/r/20250224083559.47645-8-svarbanov@suse.de
[commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Per the Cadence's "PCIe Controller IP for AX14" user guide, Version
1.04, Section 9.1.7.1, "AXI Subordinate to PCIe Address Translation
Registers", Table 9.4, the bit 16 of the AXI Subordinate Address
(axi_s_awaddr) when set corresponds to MSG with data, and when not set,
to MSG without data.
However, the driver is currently doing the opposite and due to this,
the INTx is never received on the host.
So, fix the driver to reflect the documentation and also make INTx work.
Fixes: 37dddf14f1 ("PCI: cadence: Add EndPoint Controller driver for Cadence PCIe controller")
Signed-off-by: Hans Zhang <18255117159@163.com>
Signed-off-by: Hans Zhang <hans.zhang@cixtech.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250214165724.184599-1-18255117159@163.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The new dw_pcie_find_vsec_capability() helper will be used within
different DWC APIs to find the VSEC capabilities like PTM, RAS, etc.
Co-developed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Shradha Todi <shradha.t@samsung.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Tested-by: Hrishikesh Deleep <hrishikesh.d@samsung.com>
Link: https://lore.kernel.org/r/20250221131548.59616-3-shradha.t@samsung.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Configure PBus base address and address mask to allow the hw
to detect if a given address is accessible on PCIe controller.
Fixes: f6ab898356 ("PCI: mediatek-gen3: Add Airoha EN7581 support")
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/20250225-en7581-pcie-pbus-csr-v4-2-24324382424a@kernel.org
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The BCM2712 memory map can support up to 64GB of system memory, thus
expand the inbound window size in calculation helper function.
The change is safe for the currently supported SoCs that have smaller
inbound window sizes.
Signed-off-by: Stanimir Varbanov <svarbanov@suse.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Jim Quinlan <james.quinlan@broadcom.com>
Tested-by: Ivan T. Ivanov <iivanov@suse.de>
Link: https://lore.kernel.org/r/20250224083559.47645-7-svarbanov@suse.de
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Instead of copying fields from the pcie_cfg_data structure to
brcm_pcie, reference it directly.
Signed-off-by: Stanimir Varbanov <svarbanov@suse.de>
Reviewed-by: Florian Fainelil <florian.fainelli@broadcom.com>
Reviewed-by: Jim Quinlan <james.quinlan@broadcom.com>
Tested-by: Ivan T. Ivanov <iivanov@suse.de>
Link: https://lore.kernel.org/r/20250224083559.47645-6-svarbanov@suse.de
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Then the brcmstb PCIe driver and MIP MSI-X interrupt controller
drivers are built as modules there could be a race in probing.
To avoid this, add a softdep to MIP driver to guarantee that
MIP driver will be load first.
Signed-off-by: Stanimir Varbanov <svarbanov@suse.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Tested-by: Ivan T. Ivanov <iivanov@suse.de>
Link: https://lore.kernel.org/r/20250224083559.47645-5-svarbanov@suse.de
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Calling cpumask_next_wrap_old() with starting CPU == nr_cpu_ids
is effectively the same as request to find first CPU, starting
from a given one and wrapping around if needed.
cpumask_next_wrap() is a proper replacement for that.
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Signed-off-by: Yury Norov <yury.norov@gmail.com>
The next patch aligns implementation of cpumask_next_wrap() with the
find_next_bit_wrap(), and it changes function signature.
To make the transition smooth, this patch deprecates current
implementation by adding an _old suffix. The following patches switch
current users to the new implementation one by one.
No functional changes were intended.
Signed-off-by: Yury Norov <yury.norov@gmail.com>
Enable PCIe Endpoint mode support for the Qualcomm SAR2130P platform.
This is needed, as it is not possible to use a compatible fallback on
any other platform since SAR2130P uses slightly different set of clocks.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20250221-sar2130p-pci-v3-6-61a0fdfb75b4@linaro.org
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
A call to of_parse_phandle() is incrementing the refcount, and as such,
the of_node_put() must be called when the reference is no longer needed.
Thus, refactor the existing code and add a missing of_node_put() call
following the check to ensure that "msi_np" matches "pcie->np" and after
MSI initialization, but only if the MSI support is enabled system-wide.
Cc: stable@vger.kernel.org # v5.10+
Fixes: 40ca1bf580 ("PCI: brcmstb: Add MSI support")
Signed-off-by: Stanimir Varbanov <svarbanov@suse.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250122222955.1752778-1-svarbanov@suse.de
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
On all Qcom endpoint SoCs, BAR0/BAR2 are 64bit BARs by default and
software cannot change the type.
So, mark the those BARs as 64bit BARs and also mark the successive
BAR1/BAR3 as RESERVED BARs so that the EPF drivers cannot use them.
Cc: stable+noautosel@kernel.org # depends on patch introducing only_64bit flag
Fixes: f55fee56a6 ("PCI: qcom-ep: Add Qualcomm PCIe Endpoint controller driver")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20241231130224.38206-3-manivannan.sadhasivam@linaro.org
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Remove a leftover assert for mac_reset line in mtk_pcie_en7581_power_up().
This is not harmful since EN7581 does not requires mac_reset and
mac_reset is not defined in EN7581 device tree.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20250201-pcie-en7581-remove-mac_reset-v2-1-a06786cdc683@kernel.org
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The VF driver controls an endpoint attached to the PCI HyperV
controller. An invalidation sent by the PF driver in the host
would be delivered *to* the endpoint driver by the controller
driver.
Thus, correct the wording within the comment.
Signed-off-by: Easwar Hariharan <eahariha@linux.microsoft.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Link: https://lore.kernel.org/r/20250207190716.89995-1-eahariha@linux.microsoft.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
-----BEGIN PGP SIGNATURE-----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=O62O
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.14-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Batch sizing of multiple BARs while memory decoding is disabled
instead of disabling/enabling decoding for each BAR individually;
this optimizes virtualized environments where toggling decoding
enable is expensive (Alex Williamson)
- Add host bridge .enable_device() and .disable_device() hooks for
bridges that need to configure things like Requester ID to StreamID
mapping when enabling devices (Frank Li)
- Extend struct pci_ecam_ops with .enable_device() and
.disable_device() hooks so drivers that use pci_host_common_probe()
instead of their own .probe() have a way to set the
.enable_device() callbacks (Marc Zyngier)
- Drop 'No bus range found' message so we don't complain when DTs
don't specify the default 'bus-range = <0x00 0xff>' (Bjorn Helgaas)
- Rename the drivers/pci/of_property.c struct of_pci_range to
of_pci_range_entry to avoid confusion with the global of_pci_range
in include/linux/of_address.h (Bjorn Helgaas)
Driver binding:
- Update resource request API documentation to encourage callers to
supply a driver name when requesting resources (Philipp Stanner)
- Export pci_intx_unmanaged() and pcim_intx() (always managed) so
callers of pci_intx() (which is sometimes managed) can explicitly
choose the one they need (Philipp Stanner)
- Convert drivers from pci_intx() to always-managed pcim_intx() or
never-managed pci_intx_unmanaged(): amd_sfh, ata (ahci, ata_piix,
pata_rdc, sata_sil24, sata_sis, sata_uli, sata_vsc), bnx2x, bna,
ntb, qtnfmac, rtsx, tifm_7xx1, vfio, xen-pciback (Philipp Stanner)
- Remove pci_intx_unmanaged() since pci_intx() is now always
unmanaged and pcim_intx() is always managed (Philipp Stanner)
Error handling:
- Unexport pcie_read_tlp_log() to encourage drivers to use PCI core
logging rather than building their own (Ilpo Järvinen)
- Move TLP Log handling to its own file (Ilpo Järvinen)
- Store number of supported End-End TLP Prefixes always so we can
read the correct number of DWORDs from the TLP Prefix Log (Ilpo
Järvinen)
- Read TLP Prefixes in addition to the Header Log in
pcie_read_tlp_log() (Ilpo Järvinen)
- Add pcie_print_tlp_log() to consolidate printing of TLP Header and
Prefix Log (Ilpo Järvinen)
- Quirk the Intel Raptor Lake-P PIO log size to accommodate vendor
BIOSes that don't configure it correctly (Takashi Iwai)
ASPM:
- Save parent L1 PM Substates config so when we restore it along with
an endpoint's config, the parent info isn't junk (Jian-Hong Pan)
Power management:
- Avoid D3 for Root Ports on TUXEDO Sirius Gen1 with old BIOS because
the system can't wake up from suspend (Werner Sembach)
Endpoint framework:
- Destroy the EPC device in devm_pci_epc_destroy(), which previously
didn't call devres_release() (Zijun Hu)
- Finish virtual EP removal in pci_epf_remove_vepf(), which
previously caused a subsequent pci_epf_add_vepf() to fail with
-EBUSY (Zijun Hu)
- Write BAR_MASK before iATU registers in pci_epc_set_bar() so we
don't depend on the BAR_MASK reset value being larger than the
requested BAR size (Niklas Cassel)
- Prevent changing BAR size/flags in pci_epc_set_bar() to prevent
reads from bypassing the iATU if we reduced the BAR size (Niklas
Cassel)
- Verify address alignment when programming iATU so we don't attempt
to write bits that are read-only because of the BAR size, which
could lead to directing accesses to the wrong address (Niklas
Cassel)
- Implement artpec6 pci_epc_features so we can rely on all drivers
supporting it so we can use it in EPC core code (Niklas Cassel)
- Check for BARs of fixed size to prevent endpoint drivers from
trying to change their size (Niklas Cassel)
- Verify that requested BAR size is a power of two when endpoint
driver sets the BAR (Niklas Cassel)
Endpoint framework tests:
- Clear pci-epf-test dma_chan_rx, not dma_chan_tx, after freeing
dma_chan_rx (Mohamed Khalfella)
- Correct the DMA MEMCPY test so it doesn't fail if the Endpoint
supports both DMA_PRIVATE and DMA_MEMCPY (Manivannan Sadhasivam)
- Add pci-epf-test and pci_endpoint_test support for capabilities
(Niklas Cassel)
- Add Endpoint test for consecutive BARs (Niklas Cassel)
- Remove redundant comparison from Endpoint BAR test because a > 1MB
BAR can always be exactly covered by iterating with a 1MB buffer
(Hans Zhang)
- Move and convert PCI Endpoint tests from tools/pci to Kselftests
(Manivannan Sadhasivam)
Apple PCIe controller driver:
- Convert StreamID mapping configuration from a bus notifier to the
.enable_device() and .disable_device() callbacks (Marc Zyngier)
Freescale i.MX6 PCIe controller driver:
- Add Requester ID to StreamID mapping configuration when enabling
devices (Frank Li)
- Use DWC core suspend/resume functions for imx6 (Frank Li)
- Add suspend/resume support for i.MX8MQ, i.MX8Q, and i.MX95 (Richard
Zhu)
- Add DT compatible string 'fsl,imx8q-pcie-ep' and driver support for
i.MX8Q series (i.MX8QM, i.MX8QXP, and i.MX8DXL) Endpoints (Frank
Li)
- Add DT binding for optional i.MX95 Refclk and driver support to
enable it if the platform hasn't enabled it (Richard Zhu)
- Configure PHY based on controller being in Root Complex or Endpoint
mode (Frank Li)
- Rely on dbi2 and iATU base addresses from DT via
dw_pcie_get_resources() instead of hardcoding them (Richard Zhu)
- Deassert apps_reset in imx_pcie_deassert_core_reset() since it is
asserted in imx_pcie_assert_core_reset() (Richard Zhu)
- Add missing reference clock enable or disable logic for IMX6SX,
IMX7D, IMX8MM (Richard Zhu)
- Remove redundant imx7d_pcie_init_phy() since
imx7d_pcie_enable_ref_clk() does the same thing (Richard Zhu)
Freescale Layerscape PCIe controller driver:
- Simplify by using syscon_regmap_lookup_by_phandle_args() instead
of syscon_regmap_lookup_by_phandle() followed by
of_property_read_u32_array() (Krzysztof Kozlowski)
Marvell MVEBU PCIe controller driver:
- Add MODULE_DEVICE_TABLE() to enable module autoloading (Liao Chen)
MediaTek PCIe Gen3 controller driver:
- Use clk_bulk_prepare_enable() instead of separate
clk_bulk_prepare() and clk_bulk_enable() (Lorenzo Bianconi)
- Rearrange reset assert/deassert so they're both done in the
*_power_up() callbacks (Lorenzo Bianconi)
- Document that Airoha EN7581 requires PHY init and power-on before
PHY reset deassert, unlike other MediaTek Gen3 controllers (Lorenzo
Bianconi)
- Move Airoha EN7581 post-reset delay from the en7581 clock .enable()
method to mtk_pcie_en7581_power_up() (Lorenzo Bianconi)
- Sleep instead of delay during Airoha EN7581 power-up, since this is
a non-atomic context (Lorenzo Bianconi)
- Skip PERST# assertion on Airoha EN7581 during probe and
suspend/resume to avoid a hardware defect (Lorenzo Bianconi)
- Enable async probe to reduce system startup time (Douglas Anderson)
Microchip PolarFlare PCIe controller driver:
- Set up the inbound address translation based on whether the
platform allows coherent or non-coherent DMA (Daire McNamara)
- Update DT binding such that platforms are DMA-coherent by default
and must specify 'dma-noncoherent' if needed (Conor Dooley)
Mobiveil PCIe controller driver:
- Convert mobiveil-pcie.txt to YAML and update 'interrupt-names'
and 'reg-names' (Frank Li)
Qualcomm PCIe controller driver:
- Add DT SM8550 and SM8650 optional 'global' interrupt for link
events (Neil Armstrong)
- Add DT 'compatible' strings for IPQ5424 PCIe controller (Manikanta
Mylavarapu)
- If 'global' IRQ is supported for detection of Link Up events, tell
DWC core not to wait for link up (Krishna chaitanya chundru)
Renesas R-Car PCIe controller driver:
- Avoid passing stack buffer as resource name (King Dix)
Rockchip PCIe controller driver:
- Simplify clock and reset handling by using bulk interfaces (Anand
Moon)
- Pass typed rockchip_pcie (not void) pointer to
rockchip_pcie_disable_clocks() (Anand Moon)
- Return -ENOMEM, not success, when pci_epc_mem_alloc_addr() fails
(Dan Carpenter)
Rockchip DesignWare PCIe controller driver:
- Use dll_link_up IRQ to detect Link Up and enumerate devices so
users don't have to manually rescan (Niklas Cassel)
- Tell DWC core not to wait for link up since the 'sys' interrupt is
required and detects Link Up events (Niklas Cassel)
Synopsys DesignWare PCIe controller driver:
- Don't wait for link up in DWC core if driver can detect Link Up
event (Krishna chaitanya chundru)
- Update ICC and OPP votes after Link Up events (Krishna chaitanya
chundru)
- Always stop link in dw_pcie_suspend_noirq(), which is required at
least for i.MX8QM to re-establish link on resume (Richard Zhu)
- Drop racy and unnecessary LTSSM state check before sending
PME_TURN_OFF message in dw_pcie_suspend_noirq() (Richard Zhu)
- Add struct of_pci_range.parent_bus_addr for devices that need their
immediate parent bus address, not the CPU address, e.g., to program
an internal Address Translation Unit (iATU) (Frank Li)
TI DRA7xx PCIe controller driver:
- Simplify by using syscon_regmap_lookup_by_phandle_args() instead of
syscon_regmap_lookup_by_phandle() followed by
of_parse_phandle_with_fixed_args() or of_property_read_u32_index()
(Krzysztof Kozlowski)
Xilinx Versal CPM PCIe controller driver:
- Add DT binding and driver support for Xilinx Versal CPM5
(Thippeswamy Havalige)
MicroSemi Switchtec management driver:
- Add Microchip PCI100X device IDs (Rakesh Babu Saladi)
Miscellaneous:
- Move reset related sysfs code from pci.c to pci-sysfs.c where other
similar code lives (Ilpo Järvinen)
- Simplify reset_method_store() memory management by using __free()
instead of explicit kfree() cleanup (Ilpo Järvinen)
- Constify struct bin_attribute for sysfs, VPD, P2PDMA, and the IBM
ACPI hotplug driver (Thomas Weißschuh)
- Remove redundant PCI_VSEC_HDR and PCI_VSEC_HDR_LEN_SHIFT (Dongdong
Zhang)
- Correct documentation of the 'config_acs=' kernel parameter
(Akihiko Odaki)"
* tag 'pci-v6.14-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (111 commits)
PCI: Batch BAR sizing operations
dt-bindings: PCI: microchip,pcie-host: Allow dma-noncoherent
PCI: microchip: Set inbound address translation for coherent or non-coherent mode
Documentation: Fix pci=config_acs= example
PCI: Remove redundant PCI_VSEC_HDR and PCI_VSEC_HDR_LEN_SHIFT
PCI: Don't include 'pm_wakeup.h' directly
selftests: pci_endpoint: Migrate to Kselftest framework
selftests: Move PCI Endpoint tests from tools/pci to Kselftests
misc: pci_endpoint_test: Fix IOCTL return value
dt-bindings: PCI: qcom: Document the IPQ5424 PCIe controller
dt-bindings: PCI: qcom,pcie-sm8550: Document 'global' interrupt
dt-bindings: PCI: mobiveil: Convert mobiveil-pcie.txt to YAML
PCI: switchtec: Add Microchip PCI100X device IDs
misc: pci_endpoint_test: Remove redundant 'remainder' test
misc: pci_endpoint_test: Add consecutive BAR test
misc: pci_endpoint_test: Add support for capabilities
PCI: endpoint: pci-epf-test: Add support for capabilities
PCI: endpoint: pci-epf-test: Fix check for DMA MEMCPY test
PCI: endpoint: pci-epf-test: Set dma_chan_rx pointer to NULL on error
PCI: dwc: Simplify config resource lookup
...
- Add DT binding and driver support for Xilinx Versal CPM5 (Thippeswamy
Havalige)
* pci/controller/xilinx-cpm:
PCI: xilinx-cpm: Add support for Versal CPM5 Root Port Controller 1
dt-bindings: PCI: xilinx-cpm: Add compatible string for CPM5 host1
- Set up the inbound address translation based on whether the platform
allows coherent or non-coherent DMA (Daire McNamara)
- Update DT binding such that platforms are DMA-coherent by default and
must specify 'dma-noncoherent' if needed (Conor Dooley)
* pci/controller/microchip:
dt-bindings: PCI: microchip,pcie-host: Allow dma-noncoherent
PCI: microchip: Set inbound address translation for coherent or non-coherent mode
- Use clk_bulk_prepare_enable() instead of separate clk_bulk_prepare() and
clk_bulk_enable() (Lorenzo Bianconi)
- Rearrange reset assert/deassert so they're both done in the *_power_up()
callbacks (Lorenzo Bianconi)
- Document that Airoha EN7581 requires PHY init and power-on before PHY
reset deassert, unlike other MediaTek Gen3 controllers (Lorenzo Bianconi)
- Move Airoha EN7581 post-reset delay from the en7581 clock .enable()
method to mtk_pcie_en7581_power_up() (Lorenzo Bianconi)
- Sleep instead of delay during Airoha EN7581 power-up, since this is a
non-atomic context (Lorenzo Bianconi)
- Skip PERST# assertion on Airoha EN7581 during probe and suspend/resume to
avoid a hardware defect (Lorenzo Bianconi)
- Enable async probe to reduce system startup time (Douglas Anderson)
* pci/controller/mediatek:
PCI: mediatek-gen3: Enable async probe by default
PCI: mediatek-gen3: Avoid PCIe resetting via PERST# for Airoha EN7581 SoC
PCI: mediatek-gen3: Rely on msleep() in mtk_pcie_en7581_power_up()
PCI: mediatek-gen3: Move reset delay in mtk_pcie_en7581_power_up()
PCI: mediatek-gen3: Add comment about initialization order in mtk_pcie_en7581_power_up()
PCI: mediatek-gen3: Move reset/assert callbacks in .power_up()
PCI: mediatek-gen3: Rely on clk_bulk_prepare_enable() in mtk_pcie_en7581_power_up()
- Simplify by using syscon_regmap_lookup_by_phandle_args() instead of
syscon_regmap_lookup_by_phandle() followed by
of_property_read_u32_array() (Krzysztof Kozlowski)
* pci/controller/layerscape:
PCI: layerscape: Use syscon_regmap_lookup_by_phandle_args
- Add DT compatible string 'fsl,imx8q-pcie-ep' and driver support for
i.MX8Q series (i.MX8QM, i.MX8QXP, and i.MX8DXL) Endpoints (Frank Li)
- Add DT binding for optional i.MX95 Refclk and driver support to enable it
if the platform hasn't enabled it (Richard Zhu)
- Configure PHY based on controller being in Root Complex or Endpoint mode
(Frank Li)
- Rely on dbi2 and iATU base addresses from DT via dw_pcie_get_resources()
instead of hardcoding them in imx6 (Richard Zhu)
- Skip controller_id computation for i.MX7D since it only has one
controller (Richard Zhu)
- Deassert apps_reset in imx_pcie_deassert_core_reset() since it is
asserted in imx_pcie_assert_core_reset() (Richard Zhu)
- Add missing reference clock enable or disable logic for IMX6SX, IMX7D,
IMX8MM (Richard Zhu)
- Remove redundant imx7d_pcie_init_phy() since imx7d_pcie_enable_ref_clk()
does the same thing (Richard Zhu)
* pci/controller/imx6:
PCI: imx6: Clean up comments and whitespace
PCI: imx6: Remove surplus imx7d_pcie_init_phy() function
PCI: imx6: Add missing reference clock disable logic
PCI: imx6: Deassert apps_reset in imx_pcie_deassert_core_reset()
PCI: imx6: Skip controller_id generation logic for i.MX7D
PCI: imx6: Fetch dbi2 and iATU base addesses from DT
PCI: imx6: Configure PHY based on Root Complex or Endpoint mode
PCI: imx6: Add Refclk for i.MX95 PCIe
dt-bindings: PCI: fsl,imx6q-pcie: Add Refclk for i.MX95 RC
PCI: imx6: Add i.MX8Q PCIe Endpoint (EP) support
dt-bindings: PCI: fsl,imx6q-pcie-ep: Add compatible string fsl,imx8q-pcie-ep
# Conflicts:
# drivers/pci/controller/dwc/pci-imx6.c
- Fix potential string truncation in dw_pcie_edma_irq_verify() (Niklas
Cassel)
- Don't wait for link up in DWC core if driver can detect Link Up event
(Krishna chaitanya chundru)
- If qcom 'global' IRQ is supported for detection of Link Up events, tell
DWC core not to wait for link up (Krishna chaitanya chundru)
- Update ICC and OPP votes after Link Up events (Krishna chaitanya chundru)
- Use dw-rockchip dll_link_up IRQ to detect Link Up and enumerate devices
so users don't have to manually rescan (Niklas Cassel)
- In dw-rockchip, the 'sys' interrupt is required and detects Link Up
events, so tell DWC core not to wait for link up (Niklas Cassel)
- Always stop link in dw_pcie_suspend_noirq(), which is required at least
for i.MX8QM to re-establish link on resume (Richard Zhu)
- Drop racy and unnecessary LTSSM state check before sending PME_TURN_OFF
message in dw_pcie_suspend_noirq() (Richard Zhu)
- Add stubs for dw_pcie_suspend_noirq() dw_pcie_resume_noirq() when
CONFIG_PCIE_DW_HOST is not defined so drivers don't need #ifdefs (Bjorn
Helgaas)
- Use DWC core suspend/resume functions for imx6 (Frank Li)
- Add imx6 suspend/resume support for i.MX8MQ, i.MX8Q, and i.MX95 (Richard
Zhu)
- Add struct of_pci_range.parent_bus_addr for devices that need their
immediate parent bus address, not the CPU address, e.g., to program an
internal Address Translation Unit (iATU) (Frank Li)
* pci/controller/dwc:
PCI: dwc: Simplify config resource lookup
of: address: Add parent_bus_addr to struct of_pci_range
PCI: imx6: Add i.MX8MQ, i.MX8Q and i.MX95 PM support
PCI: imx6: Use DWC common suspend resume method
PCI: dwc: Add dw_pcie_suspend_noirq(), dw_pcie_resume_noirq() stubs for !CONFIG_PCIE_DW_HOST
PCI: dwc: Remove LTSSM state test in dw_pcie_suspend_noirq()
PCI: dwc: Always stop link in the dw_pcie_suspend_noirq
PCI: dw-rockchip: Don't wait for link since we can detect Link Up
PCI: dw-rockchip: Enumerate endpoints based on dll_link_up IRQ
PCI: qcom: Update ICC and OPP values after Link Up event
PCI: qcom: Don't wait for link if we can detect Link Up
PCI: dwc: Don't wait for link up if driver can detect Link Up event
PCI: dwc: Fix potential truncation in dw_pcie_edma_irq_verify()
# Conflicts:
# drivers/pci/controller/dwc/pci-imx6.c
- Simplify by using syscon_regmap_lookup_by_phandle_args() instead of
syscon_regmap_lookup_by_phandle() followed by
of_parse_phandle_with_fixed_args() or of_property_read_u32_index()
(Krzysztof Kozlowski)
* pci/controller/dra7xx:
PCI: dra7xx: Use syscon_regmap_lookup_by_phandle_args
- Add host bridge .enable_device() and .disable_device() hooks for bridges
that need to configure things like Requester ID to StreamID mapping when
enabling devices (Frank Li)
- Add imx6 Requester ID to StreamID mapping configuration when enabling
devices (Frank Li)
- Extend struct pci_ecam_ops with .enable_device() and .disable_device()
hooks so drivers that use pci_host_common_probe() instead of their own
.probe() have a way to set the .enable_device() callbacks (Marc Zyngier)
- Convert pcie-apple StreamID mapping configuration from a bus notifier to
the .enable_device() and .disable_device() callbacks (Marc Zyngier)
* pci/controller/iommu-map:
PCI: apple: Convert to {en,dis}able_device() callbacks
PCI: host-generic: Allow {en,dis}able_device() to be provided via pci_ecam_ops
PCI: imx6: Add IOMMU and ITS MSI support for i.MX95
PCI: Add enable_device() and disable_device() callbacks for bridges
drivers, per usual, and then a handful of drivers for other SoCs. Then the
usual pile of cleanups is fairly small data fixes or converting DT bindings to
YAML so they can be validated. No changes to the core framework besides an OF
node refcount bump that never got decremented.
New Drivers:
- 5L35023 variant of Versa 3 clock generator
- Various Qualcomm clk controllers: IPQ CMN PLL, SM6115 LPASS, SM750 global,
tcsr, rpmh, and display. X Plus GPU and global. QCS615 rpmh and MSM8937 and
MSM8940 RPM.
- Qualcomm Pongo and Taycan Alpha PLLs
- Qualcomm IPQ5424 NoC-related interconnect clks
- Renesas RZ/G3E (R9A09G047) SoC clk driver
- SAMA7D65 SoC clk driver
- Samsung Exynos990 SoC clk driver
-----BEGIN PGP SIGNATURE-----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=wK9g
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"A pretty quiet cycle this time around. We have a bunch of new Qualcomm
clk drivers, per usual, and then a handful of drivers for other SoCs.
Then the usual pile of cleanups is fairly small data fixes or
converting DT bindings to YAML so they can be validated.
No changes to the core framework besides an OF node refcount bump that
never got decremented.
New Drivers:
- 5L35023 variant of Versa 3 clock generator
- Various Qualcomm clk controllers: IPQ CMN PLL, SM6115 LPASS, SM750
global, tcsr, rpmh, and display. X Plus GPU and global. QCS615 rpmh
and MSM8937 and MSM8940 RPM.
- Qualcomm Pongo and Taycan Alpha PLLs
- Qualcomm IPQ5424 NoC-related interconnect clks
- Renesas RZ/G3E (R9A09G047) SoC clk driver
- SAMA7D65 SoC clk driver
- Samsung Exynos990 SoC clk driver"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (159 commits)
clk: analogbits: Fix incorrect calculation of vco rate delta
clk: bcm: rpi: Add disp clock
clk: bcm: rpi: Create helper to retrieve private data
clk: bcm: rpi: Enable minimize for all firmware clocks
clk: bcm: rpi: Allow cpufreq driver to also adjust gpu clocks
clk: bcm: rpi: Add ISP to exported clocks
clk: stm32f4: support spread spectrum clock generation
clk: stm32f4: use FIELD helpers to access the PLLCFGR fields
dt-bindings: clock: st,stm32-rcc: support spread spectrum clocking
dt-bindings: clock: convert stm32 rcc bindings to json-schema
clk: Use str_enable_disable-like helpers
clk: clk-loongson2: Fix the number count of clk provider
clk: clk-loongson2: Switch to use devm_clk_hw_register_fixed_rate_parent_data()
clk: starfive: Make _clk_get become a common helper function
clk: en7523: Add clock for eMMC for EN7581
dt-bindings: clock: add ID for eMMC for EN7581
dt-bindings: clock: drop NUM_CLOCKS define for EN7581
clk: en7523: Rework clock handling for different clock numbers
clk: thead: Fix cpu2vp_clk for TH1520 AP_SUBSYS clocks
clk: thead: Add CLK_IGNORE_UNUSED to fix TH1520 boot
...
On Microchip PolarFire SoC the PCIe Root Port can be behind one of three
general purpose Fabric Interface Controller (FIC) buses that encapsulates
an AXI-S bus. Depending on which FIC(s) the Root Port is connected through
to CPU space, and what address translation is done by that FIC, the Root
Port driver's inbound address translation may vary.
For all current supported designs and all future expected designs, inbound
address translation done by a FIC on PolarFire SoC varies depending on
whether PolarFire SoC is operating in coherent DMA mode or noncoherent DMA
mode.
The setup of the outbound address translation tables in the Root Port
driver only needs to handle these two cases.
Setup the inbound address translation tables to one of two address
translations, depending on whether the Root Port is being used with
coherent DMA or noncoherent DMA.
Link: https://lore.kernel.org/r/20241011140043.1250030-3-daire.mcnamara@microchip.com
Fixes: 6f15a9c9f9 ("PCI: microchip: Add Microchip PolarFire PCIe controller driver")
Signed-off-by: Daire McNamara <daire.mcnamara@microchip.com>
[bhelgaas: adapt for ac7f53b7e7 ("PCI: microchip: Add support for using
either Root Port 1 or 2")]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
If platform_get_resource_byname("config") fails, return error immediately
and unindent the normal path. No functional change intended.
Link: https://lore.kernel.org/r/20250117235119.712043-1-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Call common DWC suspend/resume function. Use DWC common iATU method to
send out PME_TURN_OFF message.
In old DWC implementations, PCIE_ATU_INHIBIT_PAYLOAD in iATU Ctrl2 register
is reserved, so the generic DWC implementation of sending the PME_Turn_Off
message using a dummy MMIO write cannot be used. Use the previous method to
kick off PME_TURN_OFF message for these platforms.
The System Reset Control (SRC) interface is used to toggle 'turnoff_reset'
to send PME_TURN_OFF and since the DWC implementation is used, it is not
needed now.
Replace the imx_pcie_stop_link() and imx_pcie_host_exit() by
dw_pcie_suspend_noirq() in imx_pcie_suspend_noirq().
Since dw_pcie_suspend_noirq() already does these, see below call stack:
dw_pcie_suspend_noirq()
dw_pcie_stop_link()
imx_pcie_stop_link()
pci->pp.ops->deinit()
imx_pcie_host_exit()
Replace the imx_pcie_host_init(), dw_pcie_setup_rc() and
imx_pcie_start_link() by dw_pcie_resume_noirq() in imx_pcie_resume_noirq().
Since dw_pcie_resume_noirq() already does these, see below call stack:
dw_pcie_resume_noirq()
pci->pp.ops->init()
imx_pcie_host_init()
dw_pcie_setup_rc()
dw_pcie_start_link()
imx_pcie_start_link(;
Link: https://lore.kernel.org/r/20241126075702.4099164-9-hongxing.zhu@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously pcie-designware.h declared dw_pcie_suspend_noirq() and
dw_pcie_resume_noirq() unconditionally, even though they were only
implemented when CONFIG_PCIE_DW_HOST was defined.
Add no-op stubs for them when CONFIG_PCIE_DW_HOST is not defined so
drivers that support both Root Complex and Endpoint modes don't need
Link: https://lore.kernel.org/r/20250117213810.GA656803@bhelgaas
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
It's safe to send PME_TURN_OFF message regardless of whether the link is up
or down, so don't test the LTSSM state before sending the PME_TURN_OFF
message.
Only print an error message when the LTSSM is not in DETECT or POLL. There
shouldn't be an error when no Endpoint is connected at all.
Link: https://lore.kernel.org/r/20241210081557.163555-3-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
On the i.MX8QM, PCIe link can't be re-established again in
dw_pcie_resume_noirq(), if the LTSSM_EN bit is not cleared
properly in dw_pcie_suspend_noirq().
So, add dw_pcie_stop_link() to dw_pcie_suspend_noirq() to fix
this issue and to align the suspend/resume functions since there
is dw_pcie_start_link() in dw_pcie_resume_noirq() already.
Fixes: 4774faf854 ("PCI: dwc: Implement generic suspend/resume functionality")
Link: https://lore.kernel.org/r/20241210081557.163555-2-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The Root Complex specific device tree binding for pcie-dw-rockchip has the
'sys' interrupt marked as required.
The driver requests the 'sys' IRQ unconditionally, and errors out if not
provided.
Thus, we can unconditionally set 'use_linkup_irq', so dw_pcie_host_init()
doesn't wait for the link to come up.
This will skip the wait for link up (since the bus will be enumerated once
the link up IRQ is triggered), which reduces the bootup time.
Link: https://lore.kernel.org/r/20250113-rockchip-no-wait-v1-1-25417f37b92f@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Most boards using the pcie-dw-rockchip PCIe controller lack standard
hotplug support.
Thus, when an endpoint is attached to the SoC, users have to rescan the bus
manually to enumerate the device. This can be avoided by using the
'dll_link_up' interrupt in the combined system interrupt 'sys'.
Once the 'dll_link_up' IRQ is received, the bus underneath the host bridge
is scanned to enumerate PCIe endpoint devices.
This implements the same functionality that was implemented in the DWC
based pcie-qcom driver in 4581403f67 ("PCI: qcom: Enumerate endpoints
based on Link up event in 'global_irq' interrupt").
The Root Complex specific device tree binding for pcie-dw-rockchip already
has the 'sys' interrupt marked as required, so there is no need to update
the device tree binding. This also means that we can request the 'sys' IRQ
unconditionally.
Link: https://lore.kernel.org/r/20241127145041.3531400-2-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: commit log, squash Pei Xiao's redundant dev_err() fix from
https://lore.kernel.org/r/327718207d3cd72847c079ff9d56eb246744c182.1736126067.git.xiaopei01@kylinos.cn,
squash Niklas's #define change from https://lore.kernel.org/r/20250103095812.2408364-2-cassel@kernel.org]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
4581403f67 ("PCI: qcom: Enumerate endpoints based on Link up event in
'global_irq' interrupt") added the Link Up-based enumeration support, but
did not update the ICC/OPP vote once link is up. Before that, the update
happened during probe and the endpoints may or may not be enumerated at
that time, so the ICC/OPP vote was not guaranteed to be accurate.
With Link Up-based enumeration support, the driver can request the accurate
vote based on the PCIe link.
Call qcom_pcie_icc_opp_update() in qcom_pcie_global_irq_thread() after
enumerating the endpoints.
Fixes: 4581403f67 ("PCI: qcom: Enumerate endpoints based on Link up event in 'global_irq' interrupt")
Link: https://lore.kernel.org/r/20241123-remove_wait2-v5-3-b5f9e6b794c2@quicinc.com
Signed-off-by: Krishna chaitanya chundru <quic_krichai@quicinc.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
If we have a 'global' IRQ for Link Up events, we need not wait for the
link to be up during PCI initialization, which reduces startup time.
Check for 'global' IRQ, and if present, set 'use_linkup_irq',
so dw_pcie_host_init() doesn't wait for the link to come up.
Link: https://lore.kernel.org/r/20241123-remove_wait2-v5-2-b5f9e6b794c2@quicinc.com
Signed-off-by: Krishna chaitanya chundru <quic_krichai@quicinc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
If the driver can detect the Link Up event and enumerate downstream devices
at that time, we need not wait here.
Skip waiting for link to come up if the driver supports 'use_linkup_irq'.
Link: https://lore.kernel.org/r/20241123-remove_wait2-v5-1-b5f9e6b794c2@quicinc.com
Signed-off-by: Krishna chaitanya chundru <quic_krichai@quicinc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: wrap comment, update commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Increase the size of the string buffer to avoid potential truncation in
dw_pcie_edma_irq_verify().
This fixes the following build warning when compiling with W=1:
drivers/pci/controller/dwc/pcie-designware.c: In function ‘dw_pcie_edma_detect’:
drivers/pci/controller/dwc/pcie-designware.c:989:50: warning: ‘%d’ directive output may be truncated writing between 1 and 11 bytes into a region of size 3 [-Wformat-truncation=]
989 | snprintf(name, sizeof(name), "dma%d", pci->edma.nr_irqs);
| ^~
Link: https://lore.kernel.org/r/20250104002119.2681246-2-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Use syscon_regmap_lookup_by_phandle_args() which is a wrapper over
syscon_regmap_lookup_by_phandle() combined with getting the syscon
argument. Except simpler code this annotates within one line that given
phandle has arguments, so grepping for code would be easier.
There is also no real benefit in printing errors on missing syscon
argument, because this is done just too late: runtime check on
static/build-time data. Dtschema and Devicetree bindings offer the
static/build-time check for this already.
Link: https://lore.kernel.org/r/20250112-syscon-phandle-args-pci-v1-1-fcb6ebcc0afc@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use syscon_regmap_lookup_by_phandle_args() which is a wrapper over
syscon_regmap_lookup_by_phandle() combined with getting the syscon
argument. Except simpler code this annotates within one line that given
phandle has arguments, so grepping for code would be easier.
Link: https://lore.kernel.org/r/20250112-syscon-phandle-args-pci-v1-2-fcb6ebcc0afc@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Roy Zang <Roy.Zang@nxp.com>
This function essentially duplicates imx7d_pcie_enable_ref_clk(). So remove
it.
Link: https://lore.kernel.org/r/20241126075702.4099164-8-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Ensure the *_enable_ref_clk() function is symmetric by addressing missing
disable parts on some platforms.
Fixes: d0a75c791f ("PCI: imx6: Factor out ref clock disable to match enable")
Link: https://lore.kernel.org/r/20241126075702.4099164-7-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Since the apps_reset is asserted in imx_pcie_assert_core_reset(), it should
be deasserted in imx_pcie_deassert_core_reset().
Fixes: 9b3fe6796d ("PCI: imx6: Add code to support i.MX7D")
Link: https://lore.kernel.org/r/20241126075702.4099164-6-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
The i.MX7D only has one PCIe controller, so controller_id should always be
0. The previous code is incorrect although yielding the correct result.
Fix by removing "IMX7D" from the switch case branch.
Fixes: 2d8ed461db ("PCI: imx6: Add support for i.MX8MQ")
Link: https://lore.kernel.org/r/20241126075702.4099164-5-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Since dw_pcie_get_resources() gets the dbi2 and iATU base addresses from
DT, remove the code from the imx6 driver that does the same.
Upstream DTSes have not enabled Endpoint function. So nothing is broken for
old upstream DTBs.
Link: https://lore.kernel.org/r/20241126075702.4099164-4-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Pass PHY_MODE_PCIE_EP if the PCI controller operates in Endpoint (EP) mode,
and fix the Root Complex (RC) mode being hardcoded using a drvdata mode
check.
Fixes: 8026f2d8e8 ("PCI: imx6: Call common PHY API to set mode, speed, and submode")
Link: https://lore.kernel.org/r/20241119-pci_fixup_addr-v8-6-c4bfa5193288@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Richard Zhu <hongxing.zhu@nxp.com>
Add "ref" clock to enable Refclk. To avoid breaking DT backwards
compatibility, the i.MX95 "ref" clock is optional. Use
devm_clk_get_optional() to fetch i.MX95 PCIe optional clocks in driver.
If using external clock, "ref" clock should point to external reference.
If using internal clock, CREF_EN in LAST_TO_REG controls reference output,
implemented in drivers/clk/imx/clk-imx95-blk-ctl.c.
Link: https://lore.kernel.org/r/20241126075702.4099164-3-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Add support for the i.MX8Q series (i.MX8QM, i.MX8QXP, and i.MX8DXL) PCIe
Endpoint (EP). On the i.MX8Q platforms, the PCI bus addresses differ
from the CPU addresses. However, the DesignWare (DWC) driver already
handles this in the common code.
Link: https://lore.kernel.org/r/20241119-pci_fixup_addr-v8-7-c4bfa5193288@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Now that the core host-bridge infrastructure is able to give us a callback
on each device being added or removed, convert the bus-notifier hack to it.
Link: https://lore.kernel.org/r/20241204150145.800408-3-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
In order to let host controller drivers using the host-generic
infrastructure use the {en,dis}able_device() callbacks that can be used to
configure sideband RID mapping hardware, provide these two callbacks as
part of the pci_ecam_ops structure.
Link: https://lore.kernel.org/r/20241204150145.800408-2-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
For the i.MX95, the configuration of a LUT is necessary to convert PCIe
Requester IDs (RIDs) to StreamIDs, which are used by both IOMMU and ITS.
This involves checking msi-map and iommu-map device tree properties to
ensure consistent mapping of Requester IDs to the same StreamIDs.
Subsequently, LUT-related registers are configured. If a msi-map isn't
detected, the platform relies on DWC built-in controller for MSIs that
do not need StreamIDs.
Implement PCI bus callback function to handle enable_device() and
disable_device() operations, setting up the LUT whenever a new PCI
device is enabled.
Known limitations:
- If iommu-map exists in the device tree but the IOMMU controller is
disabled, StreamIDs are programmed into the LUT. However, if a RID
is out of range of the iommu-map, enabling the PCI device would
result in a failure, although the PCI device can work without the
IOMMU.
- If msi-map exists in the device tree but the MSI controller is
disabled, MSIs will not work. The DWC driver skips initializing the
built-in MSI controller, falling back to legacy PCI INTx only.
Link: https://lore.kernel.org/r/20250114-imx95_lut-v9-2-39f58dbed03a@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: fix uninitialized "sid" in imx_pcie_enable_device()]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Richard Zhu <hongxing.zhu@nxp.com>
Instead of marking individual interrupts as safe to be migrated in
arbitrary contexts, mark the interrupt chips, which require the interrupt
to be moved in actual interrupt context, with the new IRQCHIP_MOVE_DEFERRED
flag. This makes more sense because this is a per interrupt chip property
and not restricted to individual interrupts.
That flips the logic from the historical opt-out to a opt-in model. This is
simpler to handle for other architectures, which default to unrestricted
affinity setting. It also allows to cleanup the redundant core logic
significantly.
All interrupt chips, which belong to a top-level domain sitting directly on
top of the x86 vector domain are marked accordingly, unless the related
setup code marks the interrupts with IRQ_MOVE_PCNTXT, i.e. XEN.
No functional change intended.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Steve Wahl <steve.wahl@hpe.com>
Acked-by: Wei Liu <wei.liu@kernel.org>
Link: https://lore.kernel.org/all/20241210103335.563277044@linutronix.de
Refactor rockchip_pcie_disable_clocks() to accept a struct rockchip_pcie
pointer instead of a void pointer thus improving type safety and code
readability by explicitly specifying the expected data type.
Link: https://lore.kernel.org/r/20241202151150.7393-4-linux.amoon@gmail.com
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Currently, the driver acquires and asserts/deasserts the resets
individually thereby making the driver complex to read.
This can be simplified by using the reset_control_bulk() APIs.
Use devm_reset_control_bulk_get_exclusive() API to acquire all the resets
and use reset_control_bulk_{assert/deassert}() APIs to assert/deassert them
in bulk.
Following the recommendations in 'Rockchip RK3399 TRM v1.3 Part2':
1. Split the reset controls into two groups as per section '17.5.8.1.1
PCIe as Root Complex'.
2. Deassert the 'Pipe, MGMT Sticky, MGMT, Core' resets in groups as per
section '17.5.8.1.1 PCIe as Root Complex'. This is accomplished using
the reset_control_bulk APIs.
Link: https://lore.kernel.org/r/20241202151150.7393-3-linux.amoon@gmail.com
Co-developed-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
[kwilczynski: squash error handling fix from https://lore.kernel.org/r/7da6ac56-af55-4436-9597-6af24df8122c@stanley.mountain]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Add MODULE_DEVICE_TABLE(), so modules could be properly autoloaded based
on the alias from of_device_id table.
Link: https://lore.kernel.org/r/20240903132311.961646-1-liaochen4@huawei.com
Signed-off-by: Liao Chen <liaochen4@huawei.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Currently, the driver acquires clocks and prepare/enable/disable/unprepare
the clocks individually thereby making the driver complex to read.
The driver can be simplified by using the clk_bulk*() APIs.
Use:
- devm_clk_bulk_get_all() API to acquire all the clocks
- clk_bulk_prepare_enable() to prepare/enable clocks
- clk_bulk_disable_unprepare() APIs to disable/unprepare them in bulk
Link: https://lore.kernel.org/r/20241202151150.7393-2-linux.amoon@gmail.com
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
[bhelgaas: squash error handling fix from https://lore.kernel.org/r/20250106153041.55267-1-linux.amoon@gmail.com]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
When compiling the Rockchip endpoint driver with -W=1, the following
warnings can be seen in the output:
drivers/pci/controller/pcie-rockchip-ep.c:59: warning: Function parameter or struct member 'perst_irq' not described in 'rockchip_pcie_ep'
drivers/pci/controller/pcie-rockchip-ep.c:59: warning: Function parameter or struct member 'perst_asserted' not described in 'rockchip_pcie_ep'
drivers/pci/controller/pcie-rockchip-ep.c:59: warning: Function parameter or struct member 'link_up' not described in 'rockchip_pcie_ep'
drivers/pci/controller/pcie-rockchip-ep.c:59: warning: Function parameter or struct member 'link_training' not described in 'rockchip_pcie_ep'
Fix these warnings by adding the missing field descriptions in
struct rockchip_pcie_ep kernel-doc comment.
Fixes: a7137cbf6b ("PCI: rockchip-ep: Handle PERST# signal in EP mode")
Fixes: bd6e61df4b ("PCI: rockchip-ep: Improve link training")
Link: https://lore.kernel.org/r/20241216133404.540736-1-dlemoal@kernel.org
Reported-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The rcar_pcie_parse_outbound_ranges() uses the devm_request_mem_region()
macro to request a needed resource. A string variable that lives on the
stack is then used to store a dynamically computed resource name, which
is then passed on as one of the macro arguments. This can lead to
undefined behavior.
Depending on the current contents of the memory, the manifestations of
errors may vary. One possible output may be as follows:
$ cat /proc/iomem
30000000-37ffffff :
38000000-3fffffff :
Sometimes, garbage may appear after the colon.
In very rare cases, if no NULL-terminator is found in memory, the system
might crash because the string iterator will overrun which can lead to
access of unmapped memory above the stack.
Thus, fix this by replacing outbound_name with the name of the previously
requested resource. With the changes applied, the output will be as
follows:
$ cat /proc/iomem
30000000-37ffffff : memory2
38000000-3fffffff : memory3
Fixes: 2a6d0d63d9 ("PCI: rcar: Add endpoint mode support")
Link: https://lore.kernel.org/r/tencent_DBDCC19D60F361119E76919ADAB25EC13C06@qq.com
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: King Dix <kingdix10@qq.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The mediatek-gen3 driver can run its probe routine fairly slow on some
hardware, which adds to the total time it takes for the system start up.
Thus, turn on async mode for the probe to avoid blocking the rest of the
system.
Link: https://lore.kernel.org/r/20241220145205.1.Ibf2563896c3b1fc133bb46d3fc96ad0041763922@changeid
Signed-off-by: Douglas Anderson <dianders@chromium.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Airoha EN7581 has a hw bug asserting/releasing PERST# signal causing
occasional PCIe link down issues. In order to overcome the problem,
PERST# signal is not asserted/released during device probe or
suspend/resume phase and the PCIe block is reset using
en7523_reset_assert() and en7581_pci_enable().
Introduce flags field in the mtk_gen3_pcie_pdata struct in order to
specify per-SoC capabilities.
Link: https://lore.kernel.org/r/20250109-pcie-en7581-rst-fix-v4-1-4a45c89fb143@kernel.org
Tested-by: Hui Ma <hui.ma@airoha.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Since mtk_pcie_en7581_power_up() runs in non-atomic context, rely on
msleep() routine instead of mdelay().
Link: https://lore.kernel.org/r/20250108-pcie-en7581-fixes-v6-5-21ac939a3b9b@kernel.org
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Airoha EN7581 has a hw bug asserting/releasing PCIE_PE_RSTB signal
causing occasional PCIe link down issues. In order to overcome the
problem, PCIe block is reset using REG_PCI_CONTROL (0x88) and
REG_RESET_CONTROL (0x834) registers available in the clock module
running clk_bulk_prepare_enable() in mtk_pcie_en7581_power_up().
In order to make the code more readable, move the wait for the time
needed to complete the PCIe reset from en7581_pci_enable() to
mtk_pcie_en7581_power_up().
Reduce reset timeout from 250ms to the standard PCIE_T_PVPERL_MS value
(100ms) since it has no impact on the driver behavior.
Link: https://lore.kernel.org/r/20250108-pcie-en7581-fixes-v6-4-21ac939a3b9b@kernel.org
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Add a comment in mtk_pcie_en7581_power_up() to clarify, unlike the other
MediaTek Gen3 controllers, the Airoha EN7581 requires PHY initialization
and power-on before PHY reset deassert.
Link: https://lore.kernel.org/r/20250108-pcie-en7581-fixes-v6-3-21ac939a3b9b@kernel.org
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
In order to make the code more readable, the reset_control_bulk_assert()
function for PHY reset lines is moved to make it pair with
reset_control_bulk_deassert() in mtk_pcie_power_up() and
mtk_pcie_en7581_power_up(). The same change is done for
reset_control_assert() used to assert MAC reset line.
Introduce PCIE_MTK_RESET_TIME_US macro for the time needed to
complete PCIe reset on MediaTek controller.
Link: https://lore.kernel.org/r/20250108-pcie-en7581-fixes-v6-2-21ac939a3b9b@kernel.org
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Replace clk_bulk_prepare() and clk_bulk_enable() with
clk_bulk_prepare_enable() in mtk_pcie_en7581_power_up() routine.
Link: https://lore.kernel.org/r/20250108-pcie-en7581-fixes-v6-1-21ac939a3b9b@kernel.org
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The helper devm_clk_bulk_get_all_enable() missed to return the number of
clocks stored in the clk_bulk_data table referenced by the clks
argument and, therefore, will be dropped.
Use the newly introduced devm_clk_bulk_get_all_enabled() variant
instead, which is consistent with devm_clk_bulk_get_all() in terms of
the returned value:
> 0 if one or more clocks have been stored
= 0 if there are no clocks
< 0 if an error occurred
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20241217-clk_bulk_ena_fix-v5-2-aafbbb245155@collabora.com
Acked-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add support for the Xilinx Versal CPM5 Root Port Controller 1. The key
difference between Controller 0 and Controller 1 lies in the
platform-specific error interrupt bits, which are located at different
register offsets.
To handle these differences, updated variant structure to hold the
following platform-specific details:
- Interrupt status register offset (ir_status)
- Interrupt enable register offset (ir_enable)
- Miscellaneous interrupt values (ir_misc_value)
The driver differentiates between Controller 0 and Controller 1 using the
compatible string in the device tree. This ensures that the appropriate
register offsets are used for each controller, allowing for correct
handling of platform-specific interrupts and initialization.
Link: https://lore.kernel.org/r/20240922061318.2653503-3-thippesw@amd.com
Signed-off-by: Thippeswamy Havalige <thippesw@amd.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
All non-DWC EPC drivers implement (struct pci_epc *)->ops->get_features().
All DWC EPC drivers implement (struct dw_pcie_ep *)->ops->get_features(),
except for pcie-artpec6.c.
epc_features has been required in pci-epf-test.c since commit 6613bc2301
("PCI: endpoint: Fix NULL pointer dereference for ->get_features()").
A follow-up commit will make further use of epc_features in EPC core code.
Implement epc_features in the only EPC driver where it is currently not
implemented.
Link: https://lore.kernel.org/r/20241213143301.4158431-12-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
dw_pcie_prog_ep_inbound_atu() is used to program an inbound iATU in
"BAR Match Mode".
A memory address returned by e.g. kmalloc() is guaranteed to have natural
alignment (aligned to the size of the allocation). It is however not
guaranteed that pci_epc_set_bar() (and thus dw_pcie_prog_ep_inbound_atu())
is supplied an address that has natural alignment. (An EPF driver can send
in an arbitrary physical address to pci_epc_set_bar().)
The DWC Databook description for the LWR_TARGET_RW and LWR_TARGET_HW fields
in the IATU_LWR_TARGET_ADDR_OFF_INBOUND_i registers state that:
"Field size depends on log2(BAR_MASK+1) in BAR match mode."
I.e. only the upper bits are writable, and the number of writable bits is
dependent on the configured BAR_MASK.
Add a check to ensure that the physical address programmed in the iATU is
aligned to the size of the BAR (BAR_MASK+1), as without this, we can get
hard to debug errors, as we could write to bits that are read-only (without
getting a write error), which could cause the iATU to end up redirecting to
a physical address that is different from the address that we intended.
Link: https://lore.kernel.org/r/20241213143301.4158431-11-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
In commit 4284c88fff ("PCI: designware-ep: Allow pci_epc_set_bar() update
inbound map address") set_bar() was modified to support dynamically
changing the backing physical address of a BAR that was already configured.
This means that set_bar() can be called twice, without ever calling
clear_bar() (as calling clear_bar() would clear the BAR's PCI address
assigned by the host).
This can only be done if the new BAR size/flags does not differ from the
existing BAR configuration. Add these missing checks.
If we allow set_bar() to set e.g. a new BAR size that differs from the
existing BAR size, the new address translation range will be smaller than
the BAR size already determined by the host, which would mean that a read
past the new BAR size would pass the iATU untranslated, which could allow
the host to read memory not belonging to the new struct pci_epf_bar.
While at it, add comments which clarifies the support for dynamically
changing the physical address of a BAR. (Which was also missing.)
Fixes: 4284c88fff ("PCI: designware-ep: Allow pci_epc_set_bar() update inbound map address")
Link: https://lore.kernel.org/r/20241213143301.4158431-10-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: stable@vger.kernel.org
The "DesignWare Cores PCI Express Controller Register Descriptions,
Version 4.60a", section "1.21.70 IATU_LWR_TARGET_ADDR_OFF_INBOUND_i",
fields LWR_TARGET_RW and LWR_TARGET_HW both state that:
"Field size depends on log2(BAR_MASK+1) in BAR match mode."
I.e. only the upper bits are writable, and the number of writable bits is
dependent on the configured BAR_MASK.
If we do not write the BAR_MASK before writing the iATU registers, we are
relying the reset value of the BAR_MASK being larger than the requested
BAR size (which is supplied in the struct pci_epf_bar which is passed to
pci_epc_set_bar()). The reset value of the BAR_MASK is SoC dependent.
Thus, if the struct pci_epf_bar requests a BAR size that is larger than the
reset value of the BAR_MASK, the iATU will try to write to read-only bits,
which will cause the iATU to end up redirecting to a physical address that
is different from the address that was intended.
Thus, we should always write the iATU registers after writing the BAR_MASK.
Fixes: f8aed6ec62 ("PCI: dwc: designware: Add EP mode support")
Link: https://lore.kernel.org/r/20241213143301.4158431-9-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: stable@vger.kernel.org
- Add 0xb60b and 0xb06f Device IDs for client SKUs (Nirmal Patel)
* pci/controller/vmd:
PCI: vmd: Add DID 8086:B06F and 8086:B60B for Intel client SKUs
- Move endpoint controller cleanups that depend on refclk from the host to
the notifier that tells us the host has deasserted PERST# (Manivannan
Sadhasivam)
* pci/controller/tegra194:
PCI: tegra194: Move controller cleanups to pex_ep_event_pex_rst_deassert()
- Fix address translation unit programming (Damien Le Moal)
- Define ROCKCHIP_PCIE_AT_SIZE_ALIGN to replace magic 256 endpoint .align
value (Damien Le Moal)
- When unmapping an endpoint window, compute the region index instead of
searching for it, and verify that the address was mapped (Damien Le Moal)
- When mapping an endpoint window, verify that the address hasn't been
mapped already (Damien Le Moal)
- Implement pci_epc_ops.align_addr() for rockchip-ep (Damien Le Moal)
- Fix MSI IRQ data mapping to observe the alignment constraint, which fixes
intermittent page faults in memcpy_toio() and memcpy_fromio() (Damien Le
Moal)
- Rename rockchip_pcie_parse_ep_dt() to rockchip_pcie_ep_get_resources()
for consistency with similar DT interfaces (Damien Le Moal)
- Factor out memory allocations to tidy rockchip_pcie_ep_probe() (Damien Le
Moal)
- Factor out MSI-X quirk to tidy rockchip_pcie_ep_probe() (Damien Le Moal)
- Skip the unnecessary link train in rockchip_pcie_ep_probe() and only in
the endpoint start operation (Damien Le Moal)
- Implement pci_epc_ops.stop_link() to disable link training and controller
configuration (Damien Le Moal)
- Attempt link training at 5 GT/s when both partners support it (Damien Le
Moal)
- Add a handler for PERST# signal so we can detect host resets and start
link training when exiting reset (Damien Le Moal)
* pci/controller/rockchip:
PCI: rockchip-ep: Handle PERST# signal in EP mode
PCI: rockchip-ep: Improve link training
PCI: rockship-ep: Implement the pci_epc_ops::stop_link() operation
PCI: rockchip-ep: Refactor endpoint link training enable
PCI: rockchip-ep: Refactor rockchip_pcie_ep_probe() MSI-X hiding
PCI: rockchip-ep: Refactor rockchip_pcie_ep_probe() memory allocations
PCI: rockchip-ep: Rename rockchip_pcie_parse_ep_dt()
PCI: rockchip-ep: Fix MSI IRQ data mapping
PCI: rockchip-ep: Implement the pci_epc_ops::align_addr() operation
PCI: rockchip-ep: Improve rockchip_pcie_ep_map_addr()
PCI: rockchip-ep: Improve rockchip_pcie_ep_unmap_addr()
PCI: rockchip-ep: Use a macro to define EP controller .align feature
PCI: rockchip-ep: Fix address translation unit programming
- Enable MSI interrupts if 'global' IRQ is supported, since a previous
commit unintentionally masked them (Manivannan Sadhasivam)
- Move endpoint controller cleanups that depend on refclk from the host to
the notifier that tells us the host has deasserted PERST# (Manivannan
Sadhasivam)
- Add DT binding and driver support for IPQ9574, with Synopsys IP v5.80a
and Qcom IP 1.27.0 (devi priya)
- Move the OPP "operating-points-v2" table from the qcom,pcie-sm8450.yaml
DT binding to qcom,pcie-common.yaml, where it can be used by other Qcom
platforms (Qiang Yu)
- Add 'global' SPI interrupt for events like link-up, link-down to
qcom,pcie-x1e80100 DT binding so we can start enumeration when the link
comes up (Qiang Yu)
- Disable ASPM L0s for qcom,pcie-x1e80100 since the PHY is not tuned to
support this (Qiang Yu)
- Add ops_1_21_0 for SC8280X family SoC, which doesn't use the 'iommu-map'
DT property and doesn't need BDF-to-SID translation (Qiang Yu)
* pci/controller/qcom:
PCI: qcom: Disable ASPM L0s for X1E80100
PCI: qcom: Remove BDF2SID mapping config for SC8280X family SoC
dt-bindings: PCI: qcom,pcie-x1e80100: Add 'global' interrupt
dt-bindings: PCI: qcom: Move OPP table to qcom,pcie-common.yaml
PCI: qcom: Add support for IPQ9574
dt-bindings: PCI: qcom: Document the IPQ9574 PCIe controller
PCI: qcom-ep: Move controller cleanups to qcom_pcie_perst_deassert()
PCI: qcom: Enable MSI interrupts together with Link up if 'Global IRQ' is supported
- Add DT and driver support for using either of the two PolarFire Root
Ports (Conor Dooley)
* pci/controller/microchip:
PCI: microchip: Add support for using either Root Port 1 or 2
dt-bindings: PCI: microchip,pcie-host: Add reg for Root Port 2
- Add support for DT 'max-link-speed' and 'num-lanes' properties to
restrict the link speed and width (AngeloGioacchino Del Regno)
* pci/controller/mediatek:
PCI: mediatek-gen3: Remove unneeded semicolon
PCI: mediatek-gen3: Add support for restricting link width
PCI: mediatek-gen3: Add support for setting max-link-speed limit
- Set the 'ti,keystone-pcie' mode so v3.65a devices work in Root Complex
mode (Kishon Vijay Abraham I)
- Try to avoid unrecoverable SError for attempts to issue config
transactions when the link is down; this is racy but the best we can do
(Kishon Vijay Abraham I)
* pci/controller/keystone:
PCI: keystone: Add link up check to ks_pcie_other_map_bus()
PCI: keystone: Set mode as Root Complex for "ti,keystone-pcie" compatible
- Add PCIe support for J722S SoC (Siddharth Vadapalli)
- Delay PCIE_T_PVPERL_MS (100 ms), not just PCIE_T_PERST_CLK_US (100 us),
before deasserting PERST# to ensure power and refclk are stable
(Siddharth Vadapalli)
* pci/controller/j721e:
PCI: j721e: Deassert PERST# after a delay of PCIE_T_PVPERL_MS milliseconds
PCI: j721e: Add PCIe support for J722S SoC
- Fix suspend/resume support on i.MX6QDL, which has a hardware erratum that
prevents use of L2 (Stefan Eichenberger)
* pci/controller/imx6:
PCI: imx6: Fix suspend/resume support on i.MX6QDL
- Clear outbound address on unmap so dw_pcie_find_index() won't match an
ATU index that was already unmapped (Damien Le Moal)
- Use of_property_present() instead of of_property_read_bool() when testing
for presence of non-boolean DT properties (Rob Herring)
- Advertise 1MB size if endpoint supports Resizable BARs, which was
inadvertently lost in v6.11 (Niklas Cassel)
* pci/controller/dwc:
PCI: dwc: ep: Fix advertised resizable BAR size regression
PCI: dwc: Use of_property_present() for non-boolean properties
PCI: dwc: endpoint: Clear outbound address on unmap
- Lower severity of 'phy-names' message (Bartosz Wawrzyniak)
* pci/controller/cadence:
PCI: cadence: Lower severity of message when phy-names property is absent in DTS
- Add pci_epc_function_is_valid() to avoid repeating common validation
checks (Damien Le Moal)
- Skip attempts to allocate from endpoint controller memory window if the
requested size is larger than the window (Damien Le Moal)
- Add and document pci_epc_mem_map() and pci_epc_mem_unmap() to handle
controller-specific size and alignment constraints, and add test cases to
the endpoint test driver (Damien Le Moal)
- Implement dwc pci_epc_ops.align_addr() so pci_epc_mem_map() can observe
DWC-specific alignment requirements (Damien Le Moal)
- Synchronously cancel command handler work in endpoint test before
cleaning up DMA and BARs (Damien Le Moal)
- Respect endpoint page size in dw_pcie_ep_align_addr() (Niklas Cassel)
- Use dw_pcie_ep_align_addr() in dw_pcie_ep_raise_msi_irq() and
dw_pcie_ep_raise_msix_irq() instead of open coding the equivalent (Niklas
Cassel)
- Remove superfluous 'return' from pci_epf_test_clean_dma_chan() (Wang
Jiang)
- Avoid NULL dereference if Modem Host Interface Endpoint lacks 'mmio' DT
property (Zhongqiu Han)
- Release PCI domain ID of Endpoint controller parent (not controller
itself) and before unregistering the controller, to avoid use-after-free
(Zijun Hu)
- Clear secondary (not primary) EPC in pci_epc_remove_epf() when removing
the secondary controller associated with an NTB (Zijun Hu)
- Fix pci_epc_map map_size kerneldoc (Rick Wertenbroek)
* pci/endpoint:
PCI: endpoint: Fix pci_epc_map map_size kerneldoc string
PCI: endpoint: Clear secondary (not primary) EPC in pci_epc_remove_epf()
PCI: endpoint: Fix PCI domain ID release in pci_epc_destroy()
PCI: endpoint: epf-mhi: Avoid NULL dereference if DT lacks 'mmio'
PCI: endpoint: Remove surplus return statement from pci_epf_test_clean_dma_chan()
PCI: dwc: ep: Use align addr function for dw_pcie_ep_raise_{msi,msix}_irq()
PCI: endpoint: test: Synchronously cancel command handler work
PCI: dwc: endpoint: Implement the pci_epc_ops::align_addr() operation
PCI: endpoint: test: Use pci_epc_mem_map/unmap()
PCI: endpoint: Update documentation
PCI: endpoint: Introduce pci_epc_mem_map()/unmap()
PCI: endpoint: Improve pci_epc_mem_alloc_addr()
PCI: endpoint: Introduce pci_epc_function_is_valid()
- Add resource_set_size() to set resource size when start has already been
set (Ilpo Järvinen)
- Add resource_set_range() helper to set both resource start and size (Ilpo
Järvinen)
- Use IS_ALIGNED() and resource_size() in quirk_s3_64M() instead of
open-coding them (Ilpo Järvinen)
- Add ALIGN_DOWN_IF_NONZERO() to avoid code duplication when distributing
resources across devices (Ilpo Järvinen)
- Improve pdev_sort_resources() warning message to be more specific (Ilpo
Järvinen)
* pci/resource:
PCI: Improve pdev_sort_resources() warning message
PCI: Add ALIGN_DOWN_IF_NONZERO() helper
PCI: Use align and resource helpers, and SZ_* in quirk_s3_64M()
PCI: Use resource_set_{range,size}() helpers
resource: Add resource set range and size helpers
- Convert driver .remove_new() callbacks to .remove() again to finish the
conversion from returning 'int' to being 'void' (Sergio Paracuellos)
* pci/driver-remove:
PCI: acpiphp_ampere_altra: Switch back to struct platform_driver::remove()
PCI: controller: Switch back to struct platform_driver::remove()
Currently, the Rockchip PCIe endpoint controller driver does not handle
the PERST# signal, which prevents detecting when link training should
actually be started or if the host resets the device. This however can
be supported using the controller reset_gpios property set as an input
GPIO for endpoint mode.
Modify the Rockchip PCI endpoint controller driver to get the reset_gpio
and its associated interrupt which is serviced using a threaded IRQ with
the function rockchip_pcie_ep_perst_irq_thread() as handler.
This handler function notifies a link down event corresponding to the RC
side asserting the PERST# signal using pci_epc_linkdown() when the gpio
is high. Once the gpio value goes down, corresponding to the RC
de-asserting the PERST# signal, link training is started. The polarity
of the gpio interrupt trigger is changed from high to low after the RC
asserted PERST#, and conversely changed from low to high after the RC
de-asserts PERST#.
Also, given that the host mode controller and the endpoint mode
controller use two different property names for the same PERST# signal
(ep_gpios property and reset_gpios property respectively), for clarity,
rename the ep_gpio field of struct rockchip_pcie to perst_gpio.
Link: https://lore.kernel.org/r/20241017015849.190271-14-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
[kwilczynski: make log messages consistent, add missing include]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The Rockchip RK3399 TRM V1.3 Part2, Section 17.5.8.1.2, step 7,
describes the endpoint mode link training process clearly and states
that:
Insure link training completion and success by observing link_st field
in PCIe Client BASIC_STATUS1 register change to 2'b11. If both side
support PCIe Gen2 speed, re-train can be Initiated by asserting the
Retrain Link field in Link Control and Status Register. The software
should insure the BASIC_STATUS0[negotiated_speed] changes to "1", that
indicates re-train to Gen2 successfully.
This procedure is very similar to what is done for the root-port mode
in rockchip_pcie_host_init_port().
Implement this link training procedure for the endpoint mode as well.
Given that the RK3399 SoC does not have an interrupt signaling link
status changes, training is implemented as a delayed work which is
rescheduled until the link training completes or the endpoint controller
is stopped. The link training work is first scheduled in
rockchip_pcie_ep_start() when the endpoint function is started. Link
training completion is signaled to the function using pci_epc_linkup().
Accordingly, the linkup_notifier field of the Rockchip pci_epc_features
structure is changed to true.
Link: https://lore.kernel.org/r/20241017015849.190271-13-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
[kwilczynski: update log messages to make them consistent]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Define the EPC operation ->stop() for the Rockchip endpoint driver with
the function rockchip_pcie_ep_stop(). This function disables link
training and the controller configuration, as the reverse to what
the start operation defined with rockchip_pcie_ep_start() does.
Link: https://lore.kernel.org/r/20241017015849.190271-12-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The function rockchip_pcie_init_port() enables link training for a
controller configured in EP mode. Enabling link training is again done
in rockchip_pcie_ep_probe() after that function executed
rockchip_pcie_init_port(). Enabling link training only needs to be done
once, and doing so at the probe stage before the controller is actually
started by the user serves no purpose.
Refactor this by removing the link training enablement from both
rockchip_pcie_init_port() and rockchip_pcie_ep_probe() and moving it to
the endpoint start operation defined with rockchip_pcie_ep_start().
Enabling the controller configuration using the PCIE_CLIENT_CONF_ENABLE
bit in the same PCIE_CLIENT_CONFIG register is also moved to
rockchip_pcie_ep_start() and both the controller configuration and link
training enable bits are set with a single call to
rockchip_pcie_write().
Link: https://lore.kernel.org/r/20241017015849.190271-11-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Move the code in rockchip_pcie_ep_probe() to hide the MSI-X capability
to its own function, rockchip_pcie_ep_hide_broken_msix_cap().
No functional changes.
Link: https://lore.kernel.org/r/20241017015849.190271-10-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Introduce the function rockchip_pcie_ep_init_ob_mem() allocate the
outbound memory regions and memory needed for IRQ handling.
These changes tidy up rockchip_pcie_ep_probe().
No functional change.
Link: https://lore.kernel.org/r/20241017015849.190271-9-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
To be consistent with the usual "get_resources" naming of driver
functions that acquire controller resources like clocks, PHY etc,
rename the function rockchip_pcie_parse_ep_dt() to
rockchip_pcie_ep_get_resources().
No functional changes.
Link: https://lore.kernel.org/r/20241017015849.190271-8-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The call to rockchip_pcie_prog_ep_ob_atu() used to map the PCI address
of MSI data to the memory window allocated on probe for IRQs is done
in rockchip_pcie_ep_send_msi_irq() assuming a fixed alignment to a
256B boundary of the PCI address. This is not correct as the alignment
constraint for the RK3399 PCI mapping depends on the number of bits of
address changing in the mapped region. This leads to an unstable system
which sometimes work and sometimes does not (crashing on paging faults
when memcpy_toio() or memcpy_fromio() are used).
Similar to regular data mapping, the MSI data mapping must thus be
handled according to the information provided by
rockchip_pcie_ep_align_addr(). Modify rockchip_pcie_ep_send_msi_irq()
to use rockchip_pcie_ep_align_addr() to correctly program entry 0 of
the ATU for sending MSI IRQs.
Link: https://lore.kernel.org/r/20241017015849.190271-7-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The Rockchip PCIe endpoint controller handles PCIe transfers addresses
by masking the lower bits of the programmed PCI address and using the
same number of lower bits from the CPU address space used for the
mapping. For a PCI mapping of size bytes starting from pci_addr, the
number of bits masked is the number of address bits changing in the
address range [pci_addr..pci_addr + size - 1], up to 20 bits, that is,
up to 1MB mappings.
This means that when preparing a PCI address mapping, an endpoint
function driver must use an offset into the allocated controller
memory region that is equal to the mask of the starting PCI address
over rockchip_pcie_ep_ob_atu_num_bits() bits. This offset also
determines the maximum size of the mapping given the starting PCI
address and the fixed 1MB controller memory window size.
Implement the ->align_addr() endpoint controller operation to allow the
mapping alignment to be transparently handled by endpoint function
drivers through the function pci_epc_mem_map().
Link: https://lore.kernel.org/r/20241017015849.190271-6-dlemoal@kernel.org
Co-developed-by: Rick Wertenbroek <rick.wertenbroek@gmail.com>
Signed-off-by: Rick Wertenbroek <rick.wertenbroek@gmail.com>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
[kwilczynski: change local variable name for address offset]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add a check to verify that the outbound region to be used for mapping an
address is not already in use.
Link: https://lore.kernel.org/r/20241017015849.190271-5-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
There is no need to loop over all regions to find the memory window used
to map an address. We can use rockchip_ob_region() to determine the
region index, together with a check that the address passed as argument
is the address used to create the mapping. Furthermore, the
ob_region_map bitmap should also be checked to ensure that we are not
attempting to unmap an address that is not mapped.
Link: https://lore.kernel.org/r/20241017015849.190271-4-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Introduce the macro ROCKCHIP_PCIE_AT_SIZE_ALIGN to initialize the .align
field of the controller epc_features structure to 256. This is defined
as a shift using the macro ROCKCHIP_PCIE_AT_MIN_NUM_BITS (to avoid
using the "magic" value 8 directly).
Link: https://lore.kernel.org/r/20241017015849.190271-3-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The Rockchip PCIe endpoint controller handles PCIe transfers addresses
by masking the lower bits of the programmed PCI address and using the
same number of lower bits masked from the CPU address space used for the
mapping. For a PCI mapping of <size> bytes starting from <pci_addr>,
the number of bits masked is the number of address bits changing in the
address range [pci_addr..pci_addr + size - 1].
However, rockchip_pcie_prog_ep_ob_atu() calculates num_pass_bits only
using the size of the mapping, resulting in an incorrect number of mask
bits depending on the value of the PCI address to map.
Fix this by introducing the helper function
rockchip_pcie_ep_ob_atu_num_bits() to correctly calculate the number of
mask bits to use to program the address translation unit. The number of
mask bits is calculated depending on both the PCI address and size of
the mapping, and clamped between 8 and 20 using the macros
ROCKCHIP_PCIE_AT_MIN_NUM_BITS and ROCKCHIP_PCIE_AT_MAX_NUM_BITS. As
defined in the Rockchip RK3399 TRM V1.3 Part2, Sections 17.5.5.1.1 and
17.6.8.2.1, this clamping is necessary because:
1) The lower 8 bits of the PCI address to be mapped by the outbound
region are ignored. So a minimum of 8 address bits are needed and
imply that the PCI address must be aligned to 256.
2) The outbound memory regions are 1MB in size. So while we can specify
up to 63-bits for the PCI address (num_bits filed uses bits 0 to 5 of
the outbound address region 0 register), we must limit the number of
valid address bits to 20 to match the memory window maximum size (1
<< 20 = 1MB).
Fixes: cf590b0783 ("PCI: rockchip: Add EP driver for Rockchip PCIe controller")
Link: https://lore.kernel.org/r/20241017015849.190271-2-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
The use of of_property_read_bool() for non-boolean properties is
deprecated in favor of of_property_present() when testing for property
presence.
Link: https://lore.kernel.org/r/20241104190714.275977-1-robh@kernel.org
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Use the dw_pcie_ep_align_addr() function to calculate the alignment in
dw_pcie_ep_raise_{msi,msix}_irq() instead of open coding the same.
Link: https://lore.kernel.org/r/20241017132052.4014605-6-cassel@kernel.org
Link: https://lore.kernel.org/r/20241104205144.409236-2-cassel@kernel.org
Tested-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
[kwilczynski: squashed patch that fixes memory map sizes]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
A PCI controller device, e.g., StarFive, is parent to PCI host bridge
device. We must enable runtime PM of the controller before enabling runtime
PM of the host bridge, which will happen in pci_host_probe(), to avoid this
warning:
pcie-starfive 940000000.pcie: Enabling runtime PM for inactive device with active children
Fix this issue by enabling StarFive controller device's runtime PM before
calling pci_host_probe() in plda_pcie_host_init().
Link: https://lore.kernel.org/r/20241111-runtime_pm-v7-1-9c164eefcd87@quicinc.com
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mayank Rana <quic_mrana@quicinc.com>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Remove a surplus semicolon and fix the following warning:
./drivers/pci/controller/pcie-mediatek-gen3.c:414:2-3: Unneeded semicolon
Closes: https://bugzilla.openanolis.cn/show_bug.cgi?id=11789
Link: https://lore.kernel.org/r/20241111010935.20208-1-yang.lee@linux.alibaba.com
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
The "phy-names" property is optional, so the message indicating its
absence during the probe should be of "info" severity rather than
"error" severity.
Link: https://lore.kernel.org/r/20241018113045.2050295-1-bwawrzyn@cisco.com
Signed-off-by: Bartosz Wawrzyniak <bwawrzyn@cisco.com>
[kwilczynski: update log messages wording, commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
K2G forwards the error triggered by a link-down state (e.g., no connected
endpoint device) on the system bus for PCI configuration transactions;
these errors are reported as an SError at system level, which is fatal and
hangs the system.
So, apply fix similar to how it was done in the DesignWare Core driver
commit 15b2390634 ("PCI: dwc: Add link up check in dw_child_pcie_ops.map_bus()").
Fixes: 10a797c6e5 ("PCI: dwc: keystone: Use pci_ops for config space accessors")
Link: https://lore.kernel.org/r/20240524105714.191642-3-s-vadapalli@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
[kwilczynski: commit log, added tag for stable releases]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Cc: stable@vger.kernel.org
commit 23284ad677 ("PCI: keystone: Add support for PCIe EP in AM654x
Platforms") introduced configuring "enum dw_pcie_device_mode" as part of
device data ("struct ks_pcie_of_data"). However it failed to set the
mode for "ti,keystone-pcie" compatible.
Since the mode defaults to "DW_PCIE_UNKNOWN_TYPE", the following error
message is displayed for the v3.65a controller:
"INVALID device type 0"
Despite the driver probing successfully, the controller may not be
functional in the Root Complex mode of operation.
So, set the mode as Root Complex for "ti,keystone-pcie" compatible to
fix this.
Fixes: 23284ad677 ("PCI: keystone: Add support for PCIe EP in AM654x Platforms")
Link: https://lore.kernel.org/r/20240524105714.191642-2-s-vadapalli@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
[kwilczynski: commit log, added tag for stable releases]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Cc: stable@vger.kernel.org
The PCI host controller on PolarFire SoC has multiple Root Port instances,
each with their own bridge and ctrl address spaces. The original binding
has an "apb" register region, and it is expected to be set to the base
address of the Root Complex register space. Some defines in the Linux
driver were used to compute the addresses of the bridge and ctrl address
ranges corresponding to Root Port instance 1. Some customers want to use
Root Port instance 2 however, which requires changing the defines in the
driver, which is clearly not a portable solution.
The binding has been changed from a single register region to a pair,
corresponding to the bridge and ctrl regions respectively, so modify the
driver to read these regions directly from the devicetree rather than
compute them from the base address of the abp region.
To maintain backwards compatibility with the existing binding, the driver
retains code to handle the "abp" reg and computes the base address of the
bridge and ctrl regions using the defines if it is present. reg-names has
always been a required property, so this is safe to do.
Link: https://lore.kernel.org/r/20241107-surrender-brisket-287d563a5de1@spud
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
[bhelgaas: Capitalize PCIe spec terms]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The remapped PCIe Root Port and the child device have PM L1 Substates
capability, but they are disabled originally.
Here is a failed example on ASUS B1400CEAE:
Capabilities: [900 v1] L1 PM Substates
L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1- ASPM_L1.2+ ASPM_L1.1- L1_PM_Substates+
PortCommonModeRestoreTime=32us PortTPowerOnTime=10us
L1SubCtl1: PCI-PM_L1.2- PCI-PM_L1.1- ASPM_L1.2+ ASPM_L1.1-
T_CommonMode=0us LTR1.2_Threshold=101376ns
L1SubCtl2: T_PwrOn=50us
Enable PCI-PM L1 PM Substates for devices below VMD while they are in D0
(see PCIe r6.0, sec 5.5.4).
Link: https://lore.kernel.org/r/20241001083438.10070-4-jhp@endlessos.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218394
Signed-off-by: Jian-Hong Pan <jhp@endlessos.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Add support for this VMD device which supports the bus restriction mode.
The feature that turns off vector 0 for MSI-X remapping is also enabled.
Link: https://lore.kernel.org/r/20241011175657.249948-1-nirmal.patel@linux.intel.com
Signed-off-by: Nirmal Patel <nirmal.patel@linux.ntel.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The suspend/resume functionality is currently broken on the i.MX6QDL
platform, as documented in the NXP errata (ERR005723):
https://www.nxp.com/docs/en/errata/IMX6DQCE.pdf
This patch addresses the issue by sharing most of the suspend/resume
sequences used by other i.MX devices, while avoiding modifications to
critical registers that disrupt the PCIe functionality. It targets the
same problem as the following downstream commit:
4e92355e1f
Unlike the downstream commit, this patch also resets the connected PCIe
device if possible. Without this reset, certain drivers, such as ath10k
or iwlwifi, will crash on resume. The device reset is also done by the
driver on other i.MX platforms, making this patch consistent with
existing practices.
Upon resuming, the kernel will hang and display an error. Here's an
example of the error encountered with the ath10k driver:
ath10k_pci 0000:01:00.0: Unable to change power state from D3hot to D0, device inaccessible
Unhandled fault: imprecise external abort (0x1406) at 0x0106f944
Without this patch, suspend/resume will fail on i.MX6QDL devices if a
PCIe device is connected.
Link: https://lore.kernel.org/r/20241030103250.83640-1-eichest@gmail.com
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
[kwilczynski: commit log, added tag for stable releases]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Richard Zhu <hongxing.zhu@nxp.com>
Cc: stable@vger.kernel.org
Add support for restricting the port's link width by specifying
the num-lanes devicetree property in the PCIe node.
The setting is done in the GEN_SETTINGS register (in the driver
named as PCIE_SETTING_REG), where each set bit in [11:8] activates
a set of lanes (from bits 11 to 8 respectively, x16/x8/x4/x2).
Link: https://lore.kernel.org/r/20241104114935.172908-3-angelogioacchino.delregno@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Fei Shao <fshao@chromium.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The function dw_pcie_prog_outbound_atu() used to program outbound ATU
entries for mapping RC PCI addresses to local CPU addresses does not
allow PCI addresses that are not aligned to the value of region_align
of struct dw_pcie. This value is determined from the iATU hardware
registers during probing of the iATU (done by dw_pcie_iatu_detect()).
This value is thus valid for all DWC PCIe controllers, and valid
regardless of the hardware configuration used when synthesizing the
DWC PCIe controller.
Implement the ->align_addr() endpoint controller operation to allow
this mapping alignment to be transparently handled by endpoint function
drivers through the function pci_epc_mem_map().
Link: https://lore.kernel.org/linux-pci/20241012113246.95634-7-dlemoal@kernel.org
Link: https://lore.kernel.org/linux-pci/20241015090712.112674-1-dlemoal@kernel.org
Link: https://lore.kernel.org/linux-pci/20241017132052.4014605-5-cassel@kernel.org
Co-developed-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
[mani: squashed the patch that changed phy_addr_t to u64]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: squashed patch that updated the pci_size variable]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Add support for respecting the max-link-speed devicetree property,
forcing a maximum speed (Gen) for a PCI-Express port.
Since the MediaTek PCIe Gen3 controllers also expose the maximum
supported link speed in the PCIE_BASE_CFG register, if property
max-link-speed is specified in devicetree, validate it against the
controller capabilities and proceed setting the limitations only
if the wanted Gen is lower than the maximum one that is supported
by the controller itself (otherwise it makes no sense!).
Link: https://lore.kernel.org/r/20241104114935.172908-2-angelogioacchino.delregno@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
[kwilczynski: change dev_dbg() to dev_info() and update message wording]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Fei Shao <fshao@chromium.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Currently, the cfg_1_9_0 which is being used for X1E80100 doesn't disable
ASPM L0s. However, hardware team recommends to disable L0s as the PHY init
sequence is not tuned support L0s. Hence reuse cfg_sc8280xp for X1E80100.
Note that the config_sid() callback is not present in cfg_sc8280xp, don't
concern about this because config_sid() callback is originally a no-op
for X1E80100.
Fixes: 6d0c39324c ("PCI: qcom: Add X1E80100 PCIe support")
Link: https://lore.kernel.org/r/20241101030902.579789-5-quic_qianyu@quicinc.com
Signed-off-by: Qiang Yu <quic_qianyu@quicinc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: <stable@vger.kernel.org> # 6.9
The SC8280XP PCIe devicetree nodes do not specify an 'iommu-map' so
the config_sid() callback is effectively a no-op.
Hence introduce a new ops struct, namely ops_1_21_0 which is same as
ops_1_9_0 except that it doesn't have config_sid() callback to clean
it up.
Link: https://lore.kernel.org/r/20241101030902.579789-4-quic_qianyu@quicinc.com
Signed-off-by: Qiang Yu <quic_qianyu@quicinc.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
According to Section 2.2 of the PCI Express Card Electromechanical
Specification (Revision 5.1), in order to ensure that the power and the
reference clock are stable, PERST# has to be deasserted after a delay of
100 milliseconds (TPVPERL).
Currently, it is being assumed that the power is already stable, which
is not necessarily true.
Hence, change the delay to PCIE_T_PVPERL_MS to guarantee that power and
reference clock are stable.
Fixes: f3e25911a4 ("PCI: j721e: Add TI J721E PCIe driver")
Fixes: f96b697137 ("PCI: j721e: Use T_PERST_CLK_US macro")
Link: https://lore.kernel.org/r/20241104074420.1862932-1-s-vadapalli@ti.com
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Add the new IPQ9574 platform which is based on the Qcom IP rev. 1.27.0
and Synopsys IP rev. 5.80a.
The platform itself has four PCIe Gen3 controllers: two single-lane and
two dual-lane, all are based on Synopsys IP rev. 5.70a. As such, reuse
all the members of 'ops_2_9_0'.
Link: https://lore.kernel.org/r/20240801054803.3015572-5-quic_srichara@quicinc.com
Co-developed-by: Anusha Rao <quic_anusha@quicinc.com>
Signed-off-by: Anusha Rao <quic_anusha@quicinc.com>
Signed-off-by: devi priya <quic_devipriy@quicinc.com>
Signed-off-by: Sricharan Ramabadhran <quic_srichara@quicinc.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
TI's J722S SoC has one instance of PCIe namely PCIe0 which is a Gen3
single lane PCIe controller. Add support for the "ti,j722s-pcie-host"
compatible specific to J722S SoC.
Link: https://lore.kernel.org/r/20240524092349.158443-1-s-vadapalli@ti.com
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Currently, the endpoint cleanup function dw_pcie_ep_cleanup() and EPF
deinit notify function pci_epc_deinit_notify() are called during the
execution of pex_ep_event_pex_rst_assert() i.e., when the host has asserted
PERST#. But quickly after this step, refclk will also be disabled by the
host.
All of the tegra194 endpoint SoCs supported as of now depend on the refclk
from the host for keeping the controller operational. Due to this
limitation, any access to the hardware registers in the absence of refclk
will result in a whole endpoint crash. Unfortunately, most of the
controller cleanups require accessing the hardware registers (like eDMA
cleanup performed in dw_pcie_ep_cleanup(), etc...). So these cleanup
functions can cause the crash in the endpoint SoC once host asserts PERST#.
One way to address this issue is by generating the refclk in the endpoint
itself and not depending on the host. But that is not always possible as
some of the endpoint designs do require the endpoint to consume refclk from
the host.
Thus, fix this crash by moving the controller cleanups to the start of
the pex_ep_event_pex_rst_deassert() function. This function is called
whenever the host has deasserted PERST# and it is guaranteed that the
refclk would be active at this point. So at the start of this function
(after enabling resources) the controller cleanup can be performed. Once
finished, rest of the code execution for PERST# deassert can continue as
usual.
Fixes: 473b2cf9c4 ("PCI: endpoint: Introduce 'epc_deinit' event and notify the EPF drivers")
Fixes: 570d7715ee ("PCI: dwc: ep: Introduce dw_pcie_ep_cleanup() API for drivers supporting PERST#")
Link: https://lore.kernel.org/r/20240817-pci-qcom-ep-cleanup-v1-2-d6b958226559@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Vidya Sagar <vidyas@nvidia.com>
Cc: linux-tegra@vger.kernel.org
Currently, the endpoint cleanup function dw_pcie_ep_cleanup() and EPF
deinit notify function pci_epc_deinit_notify() are called during the
execution of qcom_pcie_perst_assert() i.e., when the host has asserted
PERST#. But quickly after this step, refclk will also be disabled by the
host.
All of the Qcom endpoint SoCs supported as of now depend on the refclk from
the host for keeping the controller operational. Due to this limitation,
any access to the hardware registers in the absence of refclk will result
in a whole endpoint crash. Unfortunately, most of the controller cleanups
require accessing the hardware registers (like eDMA cleanup performed in
dw_pcie_ep_cleanup(), powering down MHI EPF etc...). So these cleanup
functions are currently causing the crash in the endpoint SoC once host
asserts PERST#.
One way to address this issue is by generating the refclk in the endpoint
itself and not depending on the host. But that is not always possible as
some of the endpoint designs do require the endpoint to consume refclk from
the host (as I was told by the Qcom engineers).
Thus, fix this crash by moving the controller cleanups to the start of
the qcom_pcie_perst_deassert() function. qcom_pcie_perst_deassert() is
called whenever the host has deasserted PERST# and it is guaranteed that
the refclk would be active at this point. So at the start of this function
(after enabling resources), the controller cleanup can be performed. Once
finished, rest of the code execution for PERST# deassert can continue as
usual.
Fixes: 473b2cf9c4 ("PCI: endpoint: Introduce 'epc_deinit' event and notify the EPF drivers")
Fixes: 570d7715ee ("PCI: dwc: ep: Introduce dw_pcie_ep_cleanup() API for drivers supporting PERST#")
Link: https://lore.kernel.org/r/20240817-pci-qcom-ep-cleanup-v1-1-d6b958226559@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Currently, if 'Global IRQ' is supported by the platform, only the Link up
interrupt is enabled in the PARF_INT_ALL_MASK register. This masks MSIs
on some platforms. The MSI bits in PARF_INT_ALL_MASK register are enabled
by default in the hardware, but commit 4581403f67 ("PCI: qcom: Enumerate
endpoints based on Link up event in 'global_irq' interrupt") disabled them
and enabled only the Link up interrupt. While MSI continued to work on the
SM8450 platform that was used to test the offending commit, on other
platforms like SM8250, X1E80100, MSIs are getting masked. And they require
enabling the MSI interrupt bits in the register to unmask (enable) the
MSIs.
Even though the MSI interrupt enable bits in PARF_INT_ALL_MASK are
described as 'diagnostic' interrupts in the internal documentation,
disabling them masks MSI on these platforms. Due to this, MSIs were not
reported to be received these platforms while supporting 'Global IRQ'.
So, enable the MSI interrupts along with the Link up interrupt in the
PARF_INT_ALL_MASK register if 'Global IRQ' is supported. This ensures that
the MSIs continue to work and also the driver is able to catch the Link
up interrupt for enumerating endpoint devices.
Fixes: 4581403f67 ("PCI: qcom: Enumerate endpoints based on Link up event in 'global_irq' interrupt")
Closes: https://lore.kernel.org/linux-pci/9a692c98-eb0a-4d86-b642-ea655981ff53@kernel.org/
Link: https://lore.kernel.org/r/20241007051255.4378-1-manivannan.sadhasivam@linaro.org
Reported-by: Konrad Dybcio <konradybcio@kernel.org>
Tested-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> # SL7
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Qiang Yu <quic_qianyu@quicinc.com>
Clear the address mapped (outbound_addr array) in dw_pcie_ep_unmap_addr(),
to ensure that dw_pcie_find_index() does not match an ATU index that was
already unmapped.
This is in addition to clearing the ATU index bit in ob_window_map.
Link: https://lore.kernel.org/linux-pci/20241004141000.5080-1-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Convert open-coded resource size calculations to use
resource_set_{range,size}() helpers.
While at it, use SZ_* for size parameter where appropriate which makes the
intent of code more obvious.
Also, cast sizes to resource_size_t, not u64.
Link: https://lore.kernel.org/r/20240614100606.15830-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
After commit 0edb555a65 ("platform: Make platform_driver::remove() return
void") .remove() is (again) the right callback to implement for platform
drivers.
Convert all PCI controller drivers to use .remove(), with the eventual goal
to drop struct platform_driver::remove_new(). As .remove() and .remove_new()
have the same prototypes, conversion is done by just changing the structure
member name in the driver initializer.
Link: https://lore.kernel.org/r/20240923065706.728769-1-sergio.paracuellos@gmail.com
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
[bhelgaas: add pcie-xilinx-nwl.c and tidy whitespace per Uwe Kleine-König:
https://lore.kernel.org/r/tdxrmmqyzcufupnwkdbg7lwgadizm7v3lxjirykijbml7x54ze@upbdzycdsilm]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
-----BEGIN PGP SIGNATURE-----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=L3s9
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Wait for device readiness after reset by polling Vendor ID and
looking for Configuration RRS instead of polling the Command
register and looking for non-error completions, to avoid hardware
retries done for RRS on non-Vendor ID reads (Bjorn Helgaas)
- Rename CRS Completion Status to RRS ('Request Retry Status') to
match PCIe r6.0 spec usage (Bjorn Helgaas)
- Clear LBMS bit after a manual link retrain so we don't try to
retrain a link when there's no downstream device anymore (Maciej W.
Rozycki)
- Revert to the original link speed after retraining fails instead of
leaving it restricted to 2.5GT/s, so a future device has a chance
to use higher speeds (Maciej W. Rozycki)
- Wait for each level of downstream bus, not just the first, to
become accessible before restoring devices on that bus (Ilpo
Järvinen)
- Add ARCH_PCI_DEV_GROUPS so s390 can add its own attribute_groups
without having to stomp on the core's pdev->dev.groups (Lukas
Wunner)
Driver binding:
- Export pcim_request_region(), a managed counterpart of
pci_request_region(), for use by drivers (Philipp Stanner)
- Export pcim_iomap_region() and deprecate pcim_iomap_regions()
(Philipp Stanner)
- Request the PCI BAR used by xboxvideo (Philipp Stanner)
- Request and map drm/ast BARs with pcim_iomap_region() (Philipp
Stanner)
MSI:
- Add MSI_FLAG_NO_AFFINITY flag for devices that mux MSIs onto a
single IRQ line and cannot set the affinity of each MSI to a
specific CPU core (Marek Vasut)
- Use MSI_FLAG_NO_AFFINITY and remove unnecessary .irq_set_affinity()
implementations in aardvark, altera, brcmstb, dwc, mediatek-gen3,
mediatek, mobiveil, plda, rcar, tegra, vmd, xilinx-nwl,
xilinx-xdma, and xilinx drivers to avoid 'IRQ: set affinity failed'
warnings (Marek Vasut)
Power management:
- Add pwrctl support for ATH11K inside the WCN6855 package (Konrad
Dybcio)
PCI device hotplug:
- Remove unnecessary hpc_ops struct from shpchp (ngn)
- Check for PCI_POSSIBLE_ERROR(), not 0xffffffff, in cpqphp
(weiyufeng)
Virtualization:
- Mark Creative Labs EMU20k2 INTx masking as broken (Alex Williamson)
- Add an ACS quirk for Qualcomm SA8775P, which doesn't advertise ACS
but does provide ACS-like features (Subramanian Ananthanarayanan)
IOMMU:
- Add function 0 DMA alias quirk for Glenfly Arise audio function,
which uses the function 0 Requester ID (WangYuli)
NPEM:
- Add Native PCIe Enclosure Management (NPEM) support for sysfs
control of NVMe RAID storage indicators (ok/fail/locate/
rebuild/etc) (Mariusz Tkaczyk)
- Add support for the ACPI _DSM PCIe SSD status LED management, which
is functionally similar to NPEM but mediated by platform firmware
(Mariusz Tkaczyk)
Device trees:
- Drop minItems and maxItems from ranges in PCI generic host binding
since host bridges may have several MMIO and I/O port apertures
(Frank Li)
- Add kirin, rcar-gen2, uniphier DT binding top-level constraints for
clocks (Krzysztof Kozlowski)
Altera PCIe controller driver:
- Convert altera DT bindings from text to YAML (Matthew Gerlach)
- Replace TLP_REQ_ID() with macro PCI_DEVID(), which does the same
thing and is what other drivers use (Jinjie Ruan)
Broadcom STB PCIe controller driver:
- Add DT binding maxItems for reset controllers (Jim Quinlan)
- Use the 'bridge' reset method if described in the DT (Jim Quinlan)
- Use the 'swinit' reset method if described in the DT (Jim Quinlan)
- Add 'has_phy' so the existence of a 'rescal' reset controller
doesn't imply software control of it (Jim Quinlan)
- Add support for many inbound DMA windows (Jim Quinlan)
- Rename SoC 'type' to 'soc_base' express the fact that SoCs come in
families of multiple similar devices (Jim Quinlan)
- Add Broadcom 7712 DT description and driver support (Jim Quinlan)
- Sort enums, pcie_offsets[], pcie_cfg_data, .compatible strings for
maintainability (Bjorn Helgaas)
Freescale i.MX6 PCIe controller driver:
- Add imx6q-pcie 'dbi2' and 'atu' reg-names for i.MX8M Endpoints
(Richard Zhu)
- Fix a code restructuring error that caused i.MX8MM and i.MX8MP
Endpoints to fail to establish link (Richard Zhu)
- Fix i.MX8MP Endpoint occasional failure to trigger MSI by enforcing
outbound alignment requirement (Richard Zhu)
- Call phy_power_off() in the .probe() error path (Frank Li)
- Rename internal names from imx6_* to imx_* since i.MX7/8/9 are also
supported (Frank Li)
- Manage Refclk by using SoC-specific callbacks instead of switch
statements (Frank Li)
- Manage core reset by using SoC-specific callbacks instead of switch
statements (Frank Li)
- Expand comments for erratum ERR010728 workaround (Frank Li)
- Use generic PHY APIs to configure mode, speed, and submode, which
is harmless for devices that implement their own internal PHY
management and don't set the generic imx_pcie->phy (Frank Li)
- Add i.MX8Q (i.MX8QM, i.MX8QXP, and i.MX8DXL) DT binding and driver
Root Complex support (Richard Zhu)
Freescale Layerscape PCIe controller driver:
- Replace layerscape-pcie DT binding compatible fsl,lx2160a-pcie with
fsl,lx2160ar2-pcie (Frank Li)
- Add layerscape-pcie DT binding deprecated 'num-viewport' property
to address a DT checker warning (Frank Li)
- Change layerscape-pcie DT binding 'fsl,pcie-scfg' to phandle-array
(Frank Li)
Loongson PCIe controller driver:
- Increase max PCI hosts to 8 for Loongson-3C6000 and newer chipsets
(Huacai Chen)
Marvell Aardvark PCIe controller driver:
- Fix issue with emulating Configuration RRS for two-byte reads of
Vendor ID; previously it only worked for four-byte reads (Bjorn
Helgaas)
MediaTek PCIe Gen3 controller driver:
- Add per-SoC struct mtk_gen3_pcie_pdata to support multiple SoC
types (Lorenzo Bianconi)
- Use reset_bulk APIs to manage PHY reset lines (Lorenzo Bianconi)
- Add DT and driver support for Airoha EN7581 PCIe controller
(Lorenzo Bianconi)
Qualcomm PCIe controller driver:
- Update qcom,pcie-sc7280 DT binding with eight interrupts (Rayyan
Ansari)
- Add back DT 'vddpe-3v3-supply', which was incorrectly removed
earlier (Johan Hovold)
- Drop endpoint redundant masking of global IRQ events (Manivannan
Sadhasivam)
- Clarify unknown global IRQ message and only log it once to avoid a
flood (Manivannan Sadhasivam)
- Add 'linux,pci-domain' property to endpoint DT binding (Manivannan
Sadhasivam)
- Assign PCI domain number for endpoint controllers (Manivannan
Sadhasivam)
- Add 'qcom_pcie_ep' and the PCI domain number to IRQ names for
endpoint controller (Manivannan Sadhasivam)
- Add global SPI interrupt for PCIe link events to DT binding
(Manivannan Sadhasivam)
- Add global RC interrupt handler to handle 'Link up' events and
automatically enumerate hot-added devices (Manivannan Sadhasivam)
- Avoid mirroring of DBI and iATU register space so it doesn't
overlap BAR MMIO space (Prudhvi Yarlagadda)
- Enable controller resources like PHY only after PERST# is
deasserted to partially avoid the problem that the endpoint SoC
crashes when accessing things when Refclk is absent (Manivannan
Sadhasivam)
- Add 16.0 GT/s equalization and RX lane margining settings (Shashank
Babu Chinta Venkata)
- Pass domain number to pci_bus_release_domain_nr() explicitly to
avoid a NULL pointer dereference (Manivannan Sadhasivam)
Renesas R-Car PCIe controller driver:
- Make the read-only const array 'check_addr' static (Colin Ian King)
- Add R-Car V4M (R8A779H0) PCIe host and endpoint to DT binding
(Yoshihiro Shimoda)
TI DRA7xx PCIe controller driver:
- Request IRQF_ONESHOT for 'dra7xx-pcie-main' IRQ since the primary
handler is NULL (Siddharth Vadapalli)
- Handle IRQ request errors during root port and endpoint probe
(Siddharth Vadapalli)
TI J721E PCIe driver:
- Add DT 'ti,syscon-acspcie-proxy-ctrl' and driver support to enable
the ACSPCIE module to drive Refclk for the Endpoint (Siddharth
Vadapalli)
- Extract the cadence link setup from cdns_pcie_host_setup() so link
setup can be done separately during resume (Thomas Richard)
- Add T_PERST_CLK_US definition for the mandatory delay between
Refclk becoming stable and PERST# being deasserted (Thomas Richard)
- Add j721e suspend and resume support (Théo Lebrun)
TI Keystone PCIe controller driver:
- Fix NULL pointer checking when applying MRRS limitation quirk for
AM65x SR 1.0 Errata #i2037 (Dan Carpenter)
Xilinx NWL PCIe controller driver:
- Fix off-by-one error in INTx IRQ handler that caused INTx
interrupts to be lost or delivered as the wrong interrupt (Sean
Anderson)
- Rate-limit misc interrupt messages (Sean Anderson)
- Turn off the clock on probe failure and device removal (Sean
Anderson)
- Add DT binding and driver support for enabling/disabling PHYs (Sean
Anderson)
- Add PCIe phy bindings for the ZCU102 (Sean Anderson)
Xilinx XDMA PCIe controller driver:
- Add support for Xilinx QDMA Soft IP PCIe Root Port Bridge to DT
binding and xilinx-dma-pl driver (Thippeswamy Havalige)
Miscellaneous:
- Fix buffer overflow in kirin_pcie_parse_port() (Alexandra Diupina)
- Fix minor kerneldoc issues and typos (Bjorn Helgaas)
- Use PCI_DEVID() macro in aer_inject() instead of open-coding it
(Jinjie Ruan)
- Check pcie_find_root_port() return in x86 fixups to avoid NULL
pointer dereferences (Samasth Norway Ananda)
- Make pci_bus_type constant (Kunwu Chan)
- Remove unused declarations of __pci_pme_wakeup() and
pci_vpd_release() (Yue Haibing)
- Remove any leftover .*.cmd files with make clean (zhang jiao)
- Remove unused BILLION macro (zhang jiao)"
* tag 'pci-v6.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (132 commits)
PCI: Fix typos
dt-bindings: PCI: qcom: Allow 'vddpe-3v3-supply' again
tools: PCI: Remove unused BILLION macro
tools: PCI: Remove .*.cmd files with make clean
PCI: Pass domain number to pci_bus_release_domain_nr() explicitly
PCI: dra7xx: Fix error handling when IRQ request fails in probe
PCI: dra7xx: Fix threaded IRQ request for "dra7xx-pcie-main" IRQ
PCI: qcom: Add RX lane margining settings for 16.0 GT/s
PCI: qcom: Add equalization settings for 16.0 GT/s
PCI: dwc: Always cache the maximum link speed value in dw_pcie::max_link_speed
PCI: dwc: Rename 'dw_pcie::link_gen' to 'dw_pcie::max_link_speed'
PCI: qcom-ep: Enable controller resources like PHY only after refclk is available
PCI: Mark Creative Labs EMU20k2 INTx masking as broken
dt-bindings: PCI: imx6q-pcie: Add reg-name "dbi2" and "atu" for i.MX8M PCIe Endpoint
dt-bindings: PCI: altera: msi: Convert to YAML
PCI: imx6: Add i.MX8Q PCIe Root Complex (RC) support
PCI: Rename CRS Completion Status to RRS
PCI: aardvark: Correct Configuration RRS checking
PCI: Wait for device readiness with Configuration RRS
PCI: brcmstb: Sort enums, pcie_offsets[], pcie_cfg_data, .compatible strings
...
- Fix off-by-one error in INTx IRQ handler that caused INTx interrupts to
be lost or delivered as the wrong interrupt (Sean Anderson)
- Rate-limit misc interrupt messages (Sean Anderson)
- Turn off the clock on probe failure and device removal (Sean Anderson)
- Add DT binding and driver support for enabling/disabling PHYs (Sean
Anderson)
- Add PCIe phy bindings for the ZCU102 (Sean Anderson)
- Add support for Xilinx QDMA Soft IP PCIe Root Port Bridge to DT binding
and xilinx-dma-pl driver (Thippeswamy Havalige)
* pci/controller/xilinx:
PCI: xilinx-xdma: Add Xilinx QDMA Root Port driver
dt-bindings: PCI: xilinx-xdma: Add schemas for Xilinx QDMA PCIe Root Port Bridge
arm64: zynqmp: Add PCIe phys property for ZCU102
PCI: xilinx-nwl: Add PHY support
dt-bindings: pci: xilinx-nwl: Add phys property
PCI: xilinx-nwl: Clean up clock on probe failure/removal
PCI: xilinx-nwl: Rate-limit misc interrupt messages
PCI: xilinx-nwl: Fix register misspelling
PCI: xilinx-nwl: Fix off-by-one in INTx IRQ handler
- Drop endpoint redundant masking of global IRQ events (Manivannan
Sadhasivam)
- Clarify unknown global IRQ message and only log it once to avoid a flood
(Manivannan Sadhasivam)
- Add Manivannan Sadhasivam as maintainer of qcom endpoint driver
(Manivannan Sadhasivam)
- Add 'linux,pci-domain' property to endpoint DT binding (Manivannan
Sadhasivam)
- Assign PCI domain number for endpoint controllers (Manivannan Sadhasivam)
- Add 'qcom_pcie_ep' and the PCI domain number to IRQ names for endpoint
controller (Manivannan Sadhasivam)
- Add global SPI interrupt for PCIe link events to DT binding (Manivannan
Sadhasivam)
- Add global RC interrupt handler to handle 'Link up' events and
automatically enumerate hot-added devices (Manivannan Sadhasivam)
- Avoid mirroring of DBI and iATU register space so it doesn't overlap BAR
MMIO space (Prudhvi Yarlagadda)
- Enable controller resources like PHY only after PERST# is deasserted to
partially avoid the problem that the endpoint SoC crashes when accessing
things when Refclk is absent (Manivannan Sadhasivam)
- Rename dw_pcie.link_gen to max_link_speed to avoid ambiguity (Manivannan
Sadhasivam)
- Cache maximum link speed value in dw_pcie.max_link_speed for use by
vendor drivers (Manivannan Sadhasivam)
- Add 16.0 GT/s equalization and RX lane margining settings (Shashank Babu
Chinta Venkata)
- Pass domain number to pci_bus_release_domain_nr() explicitly to avoid a
NULL pointer dereference (Manivannan Sadhasivam)
* pci/controller/qcom:
PCI: Pass domain number to pci_bus_release_domain_nr() explicitly
PCI: qcom: Add RX lane margining settings for 16.0 GT/s
PCI: qcom: Add equalization settings for 16.0 GT/s
PCI: dwc: Always cache the maximum link speed value in dw_pcie::max_link_speed
PCI: dwc: Rename 'dw_pcie::link_gen' to 'dw_pcie::max_link_speed'
PCI: qcom-ep: Enable controller resources like PHY only after refclk is available
PCI: qcom: Disable mirroring of DBI and iATU register space in BAR region
PCI: qcom: Enumerate endpoints based on Link up event in 'global_irq' interrupt
dt-bindings: PCI: qcom,pcie-sm8450: Add 'global' interrupt
PCI: qcom-ep: Modify 'global_irq' and 'perst_irq' IRQ device names
PCI: endpoint: Assign PCI domain number for endpoint controllers
dt-bindings: PCI: pci-ep: Document 'linux,pci-domain' property
dt-bindings: PCI: pci-ep: Update Maintainers
PCI: qcom-ep: Reword the error message for receiving unknown global IRQ event
PCI: qcom-ep: Drop the redundant masking of global IRQ events
- Add DT "ti,syscon-acspcie-proxy-ctrl" and driver support to enable the
ACSPCIE module to drive Refclk for the Endpoint (Siddharth Vadapalli)
- Extract the cadence link setup from cdns_pcie_host_setup() so link setup
can be done separately during resume (Thomas Richard)
- Use dev_err_probe() to simplify j721e probe (Thomas Richard)
- Add T_PERST_CLK_US definition for the mandatory delay between Refclk
becoming stable and PERST# being deasserted (Thomas Richard)
- Add j721e suspend and resume support (Théo Lebrun)
* pci/controller/j721e:
PCI: j721e: Add suspend and resume support
PCI: j721e: Use T_PERST_CLK_US macro
PCI: Add T_PERST_CLK_US macro
PCI: j721e: Add reset GPIO to struct j721e_pcie
PCI: j721e: Use dev_err_probe() in the probe() function
PCI: cadence: Set cdns_pcie_host_init() global
PCI: cadence: Extract link setup sequence from cdns_pcie_host_setup()
PCI: j721e: Enable ACSPCIE Refclk if "ti,syscon-acspcie-proxy-ctrl" exists
dt-bindings: PCI: ti,j721e-pci-host: Add ACSPCIE proxy control property
- Fix a code restructuring error that caused i.MX8MM and i.MX8MP Endpoints
to fail to establish link (Richard Zhu)
- Fix i.MX8MP Endpoint occasional failure to trigger MSI by enforcing
outbound alignment requirement (Richard Zhu)
- Call phy_power_off() in the .probe() error path (Frank Li)
- Rename internal names from imx6_* to imx_* since i.MX7/8/9 are also
supported (Frank Li)
- Manage Refclk by using SoC-specific callbacks instead of switch
statements (Frank Li)
- Manage core reset by using SoC-specific callbacks instead of switch
statements (Frank Li)
- Expand comments for erratum ERR010728 workaround (Frank Li)
- Use generic PHY APIs to configure mode, speed, and submode, which is
harmless for devices that implement their own internal PHY management and
don't set the generic imx_pcie->phy (Frank Li)
- Add i.MX8Q (i.MX8QM, i.MX8QXP, and i.MX8DXL) DT binding and driver Root
Complex support (Richard Zhu)
* pci/controller/imx6:
PCI: imx6: Add i.MX8Q PCIe Root Complex (RC) support
PCI: imx6: Call common PHY API to set mode, speed, and submode
dt-bindings: PCI: imx6q-pcie: Add i.MX8Q PCIe compatible string
PCI: imx6: Consolidate redundant if-checks
PCI: imx6: Improve comment for workaround ERR010728
PCI: imx6: Simplify switch-case logic by involve core_reset callback
PCI: imx6: Introduce SoC specific callbacks for controlling REFCLK
PCI: imx6: Rename imx6_* with imx_*
PCI: imx6: Fix missing call to phy_power_off() in error handling
PCI: imx6: Fix i.MX8MP PCIe EP's occasional failure to trigger MSI
PCI: imx6: Fix establish link failure in EP mode for i.MX8MM and i.MX8MP
- Request IRQF_ONESHOT for 'dra7xx-pcie-main' IRQ since the primary handler
is NULL (Siddharth Vadapalli)
- Handle IRQ request errors during root port and endpoint probe (Siddharth
Vadapalli)
* pci/controller/dra7xx:
PCI: dra7xx: Fix error handling when IRQ request fails in probe
PCI: dra7xx: Fix threaded IRQ request for "dra7xx-pcie-main" IRQ
- Change DT binding maintainer to Jim Quinlan (Jim Quinlan)
- Add DT binding maxItems for reset controllers (Jim Quinlan)
- Refactor .probe() error handling (Jim Quinlan)
- Use the 'bridge' reset method if described in the DT (Jim Quinlan)
- Use the 'swinit' reset method if described in the DT (Jim Quinlan)
- Add SoC-specific HARD_DEBUG, INTR2_CPU_BASE register offsets (Jim
Quinlan)
- Drop unused RGR1_SW_INIT_1_INIT_MASK, RGR1_SW_INIT_1_INIT_SHIFT offsets
(Jim Quinlan)
- Add 'has_phy' so the existence of a 'rescal' reset controller doesn't
imply software control of it (Jim Quinlan)
- Add support for many inbound DMA windows (Jim Quinlan)
- Check return values of all reset_control_*() calls (Jim Quinlan)
- Rename SoC 'type' to 'soc_base' express the fact that SoCs come in
families of multiple similar devices (Jim Quinlan)
- Add Broadcom 7712 DT description and driver support (Jim Quinlan)
- Sort enums, pcie_offsets[], pcie_cfg_data, .compatible strings for
maintainability (Bjorn Helgaas)
* pci/controller/brcmstb:
PCI: brcmstb: Sort enums, pcie_offsets[], pcie_cfg_data, .compatible strings
PCI: brcmstb: Enable 7712 SoCs
PCI: brcmstb: Change field name from 'type' to 'soc_base'
PCI: brcmstb: Check return value of all reset_control_* calls
PCI: brcmstb: Refactor for chips with many regular inbound windows
PCI: brcmstb: Don't conflate the reset rescal with PHY ctrl
PCI: brcmstb: Remove two unused constants from driver
PCI: brcmstb: PCI: brcmstb: Make HARD_DEBUG, INTR2_CPU_BASE offsets SoC-specific
PCI: brcmstb: Use swinit reset if available
PCI: brcmstb: Use bridge reset if available
PCI: brcmstb: Use common error handling code in brcm_pcie_probe()
dt-bindings: PCI: brcm,stb-pcie: Add 7712 SoC description
dt-bindings: PCI: brcm,stb-pcie: Use maxItems for reset controllers
dt-bindings: PCI: brcm,stb-pcie: Change brcmstb maintainer and cleanup
- Replace TLP_REQ_ID() with macro PCI_DEVID(), which does the same thing
and is what other drivers use (Jinjie Ruan)
* pci/controller/altera:
PCI: altera: Replace TLP_REQ_ID() with macro PCI_DEVID()
Commit d4c7d1a089 ("PCI: dwc: dra7xx: Push request_irq()
call to the bottom of probe") moved the IRQ request for
"dra7xx-pcie-main" towards the end of dra7xx_pcie_probe().
However, the error handling does not take into account the
initialization performed by either dra7xx_add_pcie_port() or
dra7xx_add_pcie_ep(), depending on the mode of operation.
Fix the error handling to address this.
Fixes: d4c7d1a089 ("PCI: dwc: dra7xx: Push request_irq() call to the bottom of probe")
Link: https://lore.kernel.org/linux-pci/20240827122422.985547-3-s-vadapalli@ti.com
Tested-by: Udit Kumar <u-kumar1@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: stable@vger.kernel.org
Commit da87d35a6e ("PCI: dra7xx: Use threaded IRQ handler for
"dra7xx-pcie-main" IRQ") switched from devm_request_irq() to
devm_request_threaded_irq() for the "dra7xx-pcie-main" interrupt.
Since the primary handler was set to NULL, the "IRQF_ONESHOT" flag
should have also been set. Fix this.
Fixes: da87d35a6e ("PCI: dra7xx: Use threaded IRQ handler for "dra7xx-pcie-main" IRQ")
Suggested-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/linux-pci/20240827122422.985547-2-s-vadapalli@ti.com
Reported-by: Udit Kumar <u-kumar1@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: stable@vger.kernel.org
Add RX lane margining settings for 16.0 GT/s (GEN 4) data rate.
These settings improve link stability while operating at high date
rates and helps to improve signal quality.
Link: https://lore.kernel.org/linux-pci/20240911-pci-qcom-gen4-stability-v7-4-743f5c1fd027@linaro.org
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Shashank Babu Chinta Venkata <quic_schintav@quicinc.com>
[mani: dropped the code refactoring and minor changes]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
During high data transmission rates such as 16.0 GT/s, there is an
increased risk of signal loss due to poor channel quality and
interference. This can impact receiver's ability to capture signals
accurately.
Hence, as signal compensation is achieved through appropriate lane
equalization, apply lane equalization settings at both transmitter
and receiver which results in an increase in the PCIe signal strength.
While at it, modify the pcie-tegra194 driver to make use of the
common GEN3_EQ_CONTROL_OFF definitions in pcie-designware.h.
Link: https://lore.kernel.org/linux-pci/20240911-pci-qcom-gen4-stability-v7-3-743f5c1fd027@linaro.org
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Shashank Babu Chinta Venkata <quic_schintav@quicinc.com>
[mani: dropped the code refactoring and minor changes]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Currently, the dw_pcie::max_link_speed has a valid value only if the
controller driver restricts the maximum link speed in the driver or if
the platform does so in the devicetree using the 'max-link-speed'
property.
But having the maximum supported link speed of the platform would be
helpful for the vendor drivers to configure any link specific settings.
So in the case of non-valid value in dw_pcie::max_link_speed, just cache
the hardware default value from Link Capability register.
While at it, remove the 'max_link_speed' argument to the
dw_pcie_link_set_max_speed() function since the value can be
retrieved within the function.
Link: https://lore.kernel.org/linux-pci/20240911-pci-qcom-gen4-stability-v7-2-743f5c1fd027@linaro.org
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
The 'link_gen' field is now holding the maximum supported link speed set
either by the controller driver or by DT through 'max-link-speed'
property.
However, the name 'link_gen' sounds like the negotiated link speed of
the PCIe link.
So rename it to 'max_link_speed' to make it clear that it holds the
maximum supported link speed of the controller.
Link: https://lore.kernel.org/linux-pci/20240911-pci-qcom-gen4-stability-v7-1-743f5c1fd027@linaro.org
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
qcom_pcie_enable_resources() is called by qcom_pcie_ep_probe() and it
enables the controller resources like clocks, regulator, PHY. On one of the
new unreleased Qcom SoC, PHY enablement depends on the active refclk. And
on all of the supported Qcom endpoint SoCs, refclk comes from the host
(RC). So calling qcom_pcie_enable_resources() without refclk causes the
NoC (Network On Chip) error in the endpoint SoC and in turn results in a
whole SoC crash and rebooting into EDL (Emergency Download) mode which is
an unrecoverable state.
But qcom_pcie_enable_resources() is already called by
qcom_pcie_perst_deassert() when PERST# is deasserted, and refclk is
available at that time.
Hence, remove the unnecessary call to qcom_pcie_enable_resources() from
qcom_pcie_ep_probe() to prevent the above mentioned crash.
It should be noted that this commit prevents the crash only under normal
working condition (booting endpoint before host), but the crash may also
occur if PERST# assert happens at the wrong time. For avoiding the crash
completely, it is recommended to use SRIS mode which allows the endpoint
SoC to generate its own refclk. The driver is not supporting SRIS mode
currently, but will be added in the future.
Fixes: 869bc52534 ("PCI: dwc: ep: Fix DBI access failure for drivers requiring refclk from host")
Link: https://lore.kernel.org/linux-pci/20240830082319.51387-1-manivannan.sadhasivam@linaro.org
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Implement i.MX8Q (i.MX8QM, i.MX8QXP, and i.MX8DXL) PCIe Root Complex
(RC) support. While the controller resembles that of i.MX8MP, the PHY
differs significantly. Also, there's a distinction between PCI bus
addresses and CPU addresses.
Introduce IMX_PCIE_FLAG_CPU_ADDR_FIXUP in drvdata::flags to indicate driver
need the cpu_addr_fixup() callback to facilitate CPU address to PCI bus
address conversion according to "ranges" property.
Link: https://lore.kernel.org/linux-pci/20240729-pci2_upstream-v8-11-b68ee5ef2b4d@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: check resource_list_first_type() for NULL]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
PCIe r6.0 changed the abbreviation for "Configuration Request Retry Status"
Completion Status from "CRS" to "RRS" and uses the terminology of
"Configuration RRS Software Visibility" instead of "CRS Software
Visibility".
Align the Linux usage with the r6.0 spec language. No functional change
intended.
It's confusing to make this change, but I think "RRS" *is* a better
abbreviation because it was easy to interpret "CRS" as "Completion Retry
Status", which really didn't make any sense.
Link: https://lore.kernel.org/r/20240827234848.4429-4-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Per PCIe r6.0, sec 2.3.2, when a Root Complex handles a Completion with
Request Retry Status for a Configuration Read Request that includes both
bytes of the Vendor ID field, it must complete the Request to the host by
returning 0001h for the Vendor ID and all 1's for any additional bytes.
Previously we only returned the 0001h Vendor ID value if we got an RRS
completion for reads of exactly 4 bytes. A read of 2 bytes would not
qualify, although the spec says it should.
Check for reads of 2 or more bytes including the Vendor ID.
I don't think this will fix any observable problems because RRS only
applies to the first config reads after reset, and those are all currently
dword (4-byte) reads.
Link: https://lore.kernel.org/r/20240827234848.4429-3-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Sort enum pcie_soc_base values.
Rename pcie_offsets_bmips_7425[] to pcie_offsets_bcm7425[] to match BCM7425
pcie_soc_base enum, bcm7425_cfg, and "brcm,bcm7425-pcie" .compatible
string.
Rename pcie_offset_bcm7278[] to pcie_offsets_bcm7278[] to match other
"pcie_offsets" names.
Rename pcie_offset_bcm7712[] to pcie_offsets_bcm7712[] to match other
"pcie_offsets" names.
Sort pcie_offsets_*[] by SoC name, move them all together, indent values
for easy reading.
Sort pcie_cfg_data structs by SoC name.
Sort .compatible strings by SoC name.
No functional change intended.
Link: https://lore.kernel.org/r/20240902205456.227409-1-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Invoke the common PHY API to configure mode, speed, and submode. While
these functions are optional in the PHY interface, they are necessary for
certain PHY drivers. Lack of support for these functions in a PHY driver
does not cause harm.
Link: https://lore.kernel.org/linux-pci/20240729-pci2_upstream-v8-10-b68ee5ef2b4d@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Consolidated redundant if-checks pertaining to imx_pcie->phy. Instead of
two separate checks, merged them into one to improve code readability.
Link: https://lore.kernel.org/linux-pci/20240729-pci2_upstream-v8-8-b68ee5ef2b4d@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Instead of using the switch case statement to assert/dassert the core
reset handled by this driver itself, let's introduce a new callback
core_reset() and define it for platforms that require it.
This simplifies the code.
Link: https://lore.kernel.org/linux-pci/20240729-pci2_upstream-v8-5-b68ee5ef2b4d@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Instead of using the switch case statement to enable/disable the
reference clock handled by this driver itself, let's introduce a new
callback enable_ref_clk() and define it for platforms that require it.
This simplifies the code.
Link: https://lore.kernel.org/linux-pci/20240729-pci2_upstream-v8-5-b68ee5ef2b4d@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Since this driver has evolved to support other i.MX SoCs such as
i.MX7/8/9, thus rename the 'imx6' prefix to 'imx' to avoid confusion.
The driver name is left unchanged to avoid breaking userspace.
Link: https://lore.kernel.org/linux-pci/20240729-pci2_upstream-v8-3-b68ee5ef2b4d@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
[kwilczynski: commit log, refactor the IMX_* macros]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Fix missing call to phy_power_off() in the error path of
imx6_pcie_host_init(). Remove unnecessary check for imx6_pcie->phy
as the PHY API already handles NULL pointers.
Fixes: cbcf8722b5 ("phy: freescale: imx8m-pcie: Fix the wrong order of phy_init() and phy_power_on()")
Link: https://lore.kernel.org/linux-pci/20240729-pci2_upstream-v8-3-b68ee5ef2b4d@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: <stable@vger.kernel.org> # 6.1+
Correct occasional MSI triggering failures in i.MX8MP PCIe EP by applying
the correct hardware outbound alignment requirement.
The i.MX platform has a restriction about outbound address translation. The
pci-epc-mem uses page_size to manage it. Set the correct page_size for i.MX
platform to meet the hardware requirement, which is the same as inbound
address alignment.
Thus, align it with epc_features::align.
Fixes: 1bd0d43dcf ("PCI: imx6: Clean up addr_space retrieval code")
Link: https://lore.kernel.org/linux-pci/20240729-pci2_upstream-v8-2-b68ee5ef2b4d@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Jason Liu <jason.hui.liu@nxp.com>
Cc: <stable@vger.kernel.org> # 6.9+
Add IMX6_PCIE_FLAG_HAS_APP_RESET flag to IMX8MM_EP and IMX8MP_EP drvdata.
This flag was overlooked during code restructuring. It is crucial to
release the app-reset from the System Reset Controller before initiating
LTSSM to rectify the issue.
Fixes: 0c9651c21f ("PCI: imx6: Simplify reset handling by using *_FLAG_HAS_*_RESET")
Link: https://lore.kernel.org/linux-pci/20240729-pci2_upstream-v8-1-b68ee5ef2b4d@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: <stable@vger.kernel.org> # 6.9+
The Broadcom STB 7712 is the sibling chip of the RPi 5 (2712). It has
one PCIe controller with a single port, supports gen2 and one lane only.
The current revision of the chip is "C0" or "C1".
Link: https://lore.kernel.org/linux-pci/20240815225731.40276-14-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Stanimir Varbanov <svarbanov@suse.de>
The 'type' field used in the driver to discern SoC differences is
confusing; change it to the more apt 'soc_base'.
The 'base' is because some SoCs have the same characteristics as
previous SoCs so it is convenient to classify them in the same group.
Link: https://lore.kernel.org/linux-pci/20240815225731.40276-13-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Always check the return value for invocations of reset_control_xxx() and
propagate the error to the next level.
Although the current functions in reset-brcmstb.c cannot fail, this may
someday change.
Link: https://lore.kernel.org/linux-pci/20240815225731.40276-12-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Stanimir Varbanov <svarbanov@suse.de>
Provide support for new chips with multiple inbound windows while
keeping the legacy support for the older chips.
In existing chips there are three inbound windows with fixed purposes:
the first was for mapping SoC internal registers, the second was for
memory, and the third was for memory but with the endian swapped.
Typically, only one window was used.
Complicating the inbound window usage was the fact that the PCIe HW
would do a baroque internal mapping of system memory, and concatenate
the regions of multiple memory controllers.
Newer chips such as the 7712 and Cable Modem SoCs take a step forward
and drop the internal mapping while providing for multiple inbound
windows. This works in concert with the dma-ranges property, where each
provided range becomes an inbound window.
Link: https://lore.kernel.org/linux-pci/20240815225731.40276-11-james.quinlan@broadcom.com
Co-developed-by: Riyan Dhiman <riyandhiman14@gmail.com>
Signed-off-by: Riyan Dhiman <riyandhiman14@gmail.com>
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
[kwilczynski: commit log, wrap code comments to 80 columns]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Stanimir Varbanov <svarbanov@suse.de>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Within kirin_pcie_parse_port(), the pcie->num_slots is compared to
pcie->gpio_id_reset size (MAX_PCI_SLOTS) which is correct and would lead
to an overflow.
Thus, fix condition to pcie->num_slots + 1 >= MAX_PCI_SLOTS and move
pcie->num_slots increment below the if-statement to avoid out-of-bounds
array access.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: b22dbbb245 ("PCI: kirin: Support PERST# GPIOs for HiKey970 external PEX 8606 bridge")
Link: https://lore.kernel.org/linux-pci/20240903115823.30647-1-adiupina@astralinux.ru
Signed-off-by: Alexandra Diupina <adiupina@astralinux.ru>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The TLP_REQ_ID's function is same as current PCI_DEVID()
macro, replace it.
No functional changes intended.
Link: https://lore.kernel.org/linux-pci/20240828104202.3683491-1-ruanjinjie@huawei.com
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Add suspend and resume support. Only the Root Complex mode is supported.
During the suspend stage PERST# is asserted, then deasserted during the
resume stage.
Link: https://lore.kernel.org/linux-pci/20240102-j7200-pcie-s2r-v7-7-a2f9156da6c3@bootlin.com
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
[kwilczynski: commit log, update references to the PCI SIG specification]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Add a "has_phy" field indicating that the internal PHY has SW control
that requires configuration. Some previous chips only required the
firing of the "rescal" reset controller.
This change requires us to give the 7216 SoC its own cfg_data structure.
Link: https://lore.kernel.org/linux-pci/20240815225731.40276-10-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Stanimir Varbanov <svarbanov@suse.de>
Remove two constants in the driver which are no longer
used: RGR1_SW_INIT_1_INIT_MASK and RGR1_SW_INIT_1_INIT_SHIFT.
Link: https://lore.kernel.org/linux-pci/20240815225731.40276-9-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Stanimir Varbanov <svarbanov@suse.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Do preparatory work for the 7712 SoC, which is introduced in a
future commit.
Our HW design has changed two register offsets for the 7712, where
previously it was a common value for all Broadcom SoCs with PCIe
cores.
Specifically, the two offsets are to the registers HARD_DEBUG and
INTR2_CPU_BASE.
Link: https://lore.kernel.org/linux-pci/20240815225731.40276-8-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Stanimir Varbanov <svarbanov@suse.de>
The 7712 SoC adds a software init reset device for the PCIe HW.
If found in the DT node, use it.
Link: https://lore.kernel.org/linux-pci/20240815225731.40276-7-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The 7712 SoC has a bridge reset which can be described in the device
tree.
Use it if present. Otherwise, continue to use the legacy method to
reset the bridge.
Link: https://lore.kernel.org/linux-pci/20240815225731.40276-6-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
[kwilczynski: commit log, refactored function brcm_pcie_bridge_sw_init_set_generic()]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Stanimir Varbanov <svarbanov@suse.de>
Refactor the error handling in the bottom half of the probe function
for readability.
The invocation of clk_prepare_enable() is moved lower in the function
and this simplifies a couple of return paths. The dev_err_probe() is
also used when it is apt.
Link: https://lore.kernel.org/linux-pci/20240815225731.40276-5-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Struct cdns_pcie_rc once had a .dev member, but it was removed by
bd22885aa1 ("PCI: cadence: Refactor driver to use as a core library").
Drop the extra kerneldoc for it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Struct mtk_pcie.mem was removed by 8a26f861b8 ("PCI: mediatek: Use
pci_parse_request_of_pci_ranges()"), but the kerneldoc was left. Remove
the extra kerneldoc.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add reset GPIO to struct j721e_pcie, so it can be used at suspend and
resume stages.
Link: https://lore.kernel.org/linux-pci/20240102-j7200-pcie-s2r-v7-4-a2f9156da6c3@bootlin.com
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Use dev_err_probe() instead of dev_err() in the probe() function to
simplify the code and standardize the error output.
Link: https://lore.kernel.org/linux-pci/20240102-j7200-pcie-s2r-v7-3-a2f9156da6c3@bootlin.com
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
During the resume sequence of the host, cdns_pcie_host_init() needs to be
called, so set it global.
The dev function parameter is removed, as it isn't used.
Link: https://lore.kernel.org/linux-pci/20240102-j7200-pcie-s2r-v7-2-a2f9156da6c3@bootlin.com
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
The function cdns_pcie_host_setup() mixes probe structure and link setup.
The link setup must be done during the resume sequence. So extract it from
cdns_pcie_host_setup() and create a dedicated function.
Link: https://lore.kernel.org/linux-pci/20240102-j7200-pcie-s2r-v7-1-a2f9156da6c3@bootlin.com
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Introduce support for Airoha EN7581 PCIe controller to mediatek-gen3
PCIe controller driver.
Link: https://lore.kernel.org/linux-pci/aca00bd672ee576ad96d279414fc0835ff31f637.1720022580.git.lorenzo@kernel.org
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Tested-by: Zhengping Zhang <zhengping.zhang@airoha.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Jianjun Wang <jianjun.wang@mediatek.com>
Use reset_bulk APIs to manage PHY reset lines.
This is a preliminary patch in order to add Airoha EN7581 PCIe support.
Link: https://lore.kernel.org/linux-pci/3ceb83bc0defbcf868521f8df4b9100e55ec2614.1720022580.git.lorenzo@kernel.org
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Tested-by: Zhengping Zhang <zhengping.zhang@airoha.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Jianjun Wang <jianjun.wang@mediatek.com>
Introduce mtk_gen3_pcie_pdata data structure in order to define
multiple callbacks for each supported SoC.
This is a preliminary patch to introduce EN7581 PCIe support.
Link: https://lore.kernel.org/linux-pci/c193d1a87505d045e2e0ef33317bce17012ee095.1720022580.git.lorenzo@kernel.org
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Tested-by: Zhengping Zhang <zhengping.zhang@airoha.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Jianjun Wang <jianjun.wang@mediatek.com>
Don't populate the const read-only array check_addr on the stack at
run time, instead make it static.
Link: https://lore.kernel.org/linux-pci/20240822205941.643187-1-colin.i.king@gmail.com
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
[kwilczynski: refactor array definition]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
The code in vmd_shutdown() had an indentation issue where spaces were
used instead of tabs. This commit corrects the indentation to use tabs,
adhering to the Linux kernel coding style guidelines.
Issue reported by the checkpatch.pl script:
ERROR: code indent should use tabs where possible
#1056: FILE: drivers/pci/controller/vmd.c:1056:
+ struct vmd_dev *vmd = pci_get_drvdata(dev);$
WARNING: please, no spaces at the start of a line
#1056: FILE: drivers/pci/controller/vmd.c:1056:
+ struct vmd_dev *vmd = pci_get_drvdata(dev);$
ERROR: code indent should use tabs where possible
#1058: FILE: drivers/pci/controller/vmd.c:1058:
+ vmd_remove_irq_domain(vmd);$
WARNING: please, no spaces at the start of a line
#1058: FILE: drivers/pci/controller/vmd.c:1058:
+ vmd_remove_irq_domain(vmd);$
No functional changes are intended.
Link: https://lore.kernel.org/linux-pci/20240901092602.17414-1-riyandhiman14@gmail.com
Signed-off-by: Riyan Dhiman <riyandhiman14@gmail.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
PARF hardware block which is a wrapper on top of DWC PCIe controller
mirrors the DBI and ATU register space. It uses PARF_SLV_ADDR_SPACE_SIZE
register to get the size of the memory block to be mirrored and uses
PARF_DBI_BASE_ADDR, PARF_ATU_BASE_ADDR registers to determine the base
address of DBI and ATU space inside the memory block that is being
mirrored.
When a memory region which is located above the SLV_ADDR_SPACE_SIZE
boundary is used for BAR region then there could be an overlap of DBI and
ATU address space that is getting mirrored and the BAR region. This
results in DBI and ATU address space contents getting updated when a PCIe
function driver tries updating the BAR/MMIO memory region. Reference
memory map of the PCIe memory region with DBI and ATU address space
overlapping BAR region is as below.
|---------------|
| |
| |
------- --------|---------------|
| | |---------------|
| | | DBI |
| | |---------------|---->DBI_BASE_ADDR
| | | |
| | | |
| PCIe | |---->2*SLV_ADDR_SPACE_SIZE
| BAR/MMIO|---------------|
| Region | ATU |
| | |---------------|---->ATU_BASE_ADDR
| | | |
PCIe | |---------------|
Memory | | DBI |
Region | |---------------|---->DBI_BASE_ADDR
| | | |
| --------| |
| | |---->SLV_ADDR_SPACE_SIZE
| |---------------|
| | ATU |
| |---------------|---->ATU_BASE_ADDR
| | |
| |---------------|
| | DBI |
| |---------------|---->DBI_BASE_ADDR
| | |
| | |
----------------|---------------|
| |
| |
| |
|---------------|
Currently memory region beyond the SLV_ADDR_SPACE_SIZE boundary is not
used for BAR region which is why the above mentioned issue is not
encountered. This issue is discovered as part of internal testing when we
tried moving the BAR region beyond the SLV_ADDR_SPACE_SIZE boundary. Hence
we are trying to fix this.
As PARF hardware block mirrors DBI and ATU register space after every
PARF_SLV_ADDR_SPACE_SIZE (default 0x1000000) boundary multiple, program
maximum possible size to this register by writing 0x80000000 to it(it
considers only powers of 2 as values) to avoid mirroring DBI and ATU to
BAR/MMIO region. Write the physical base address of DBI and ATU register
blocks to PARF_DBI_BASE_ADDR (default 0x0) and PARF_ATU_BASE_ADDR (default
0x1000) respectively to make sure DBI and ATU blocks are at expected
memory locations.
The register offsets PARF_DBI_BASE_ADDR_V2, PARF_SLV_ADDR_SPACE_SIZE_V2
and PARF_ATU_BASE_ADDR are applicable for platforms that use Qcom IP
rev 1.9.0, 2.7.0 and 2.9.0. PARF_DBI_BASE_ADDR_V2 and
PARF_SLV_ADDR_SPACE_SIZE_V2 are applicable for Qcom IP rev 2.3.3.
PARF_DBI_BASE_ADDR and PARF_SLV_ADDR_SPACE_SIZE are applicable for Qcom
IP rev 1.0.0, 2.3.2 and 2.4.0. Update init()/post_init() functions of the
respective Qcom IP versions to program applicable PARF_DBI_BASE_ADDR,
PARF_SLV_ADDR_SPACE_SIZE and PARF_ATU_BASE_ADDR register offsets. Update
the SLV_ADDR_SPACE_SZ macro to 0x80000000 to set highest bit in
PARF_SLV_ADDR_SPACE_SIZE register.
Cache DBI and iATU physical addresses in 'struct dw_pcie' so that
pcie_qcom.c driver can program these addresses in the PARF_DBI_BASE_ADDR
and PARF_ATU_BASE_ADDR registers.
Suggested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/linux-pci/20240814220338.1969668-1-quic_pyarlaga@quicinc.com
Signed-off-by: Prudhvi Yarlagadda <quic_pyarlaga@quicinc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Mayank Rana <quic_mrana@quicinc.com>
Historically, Qcom PCIe RC controllers lacked standard hotplug support. So
when an endpoint is attached to the SoC, users have to rescan the bus
manually to enumerate the device. But this can be avoided by using the Link
up event exposed by the Qcom specific 'global_irq' interrupt.
Qcom PCIe RC controllers are capable of generating the 'global' SPI
interrupt to the host CPUs. The device driver can use this interrupt to
identify events such as PCIe link specific events, safety events etc...
One such event is the PCIe Link up event generated when an endpoint is
detected on the bus and the Link is 'up'. This event can be used to
enumerate the PCIe endpoint devices without user intervention.
So add support for capturing the PCIe Link up event using the 'global'
interrupt in the driver. Once the Link up event is received, the bus
underneath the host bridge is scanned to enumerate PCIe endpoint devices.
All of the Qcom SoCs have only one Root Port per controller instance. So
only a single 'Link up' event is generated for the PCIe controller.
Link: https://lore.kernel.org/linux-pci/20240828-pci-qcom-hotplug-v4-11-263a385fbbcb@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Currently, the IRQ device name for both of these IRQs doesn't have Qcom
specific prefix and PCIe domain number. This causes 2 issues:
1. Pollutes the global IRQ namespace since 'global' is a common name.
2. When more than one EP controller instance is present in the SoC, naming
conflict will occur.
Hence, add 'qcom_pcie_ep_' prefix and PCIe domain number suffix to the IRQ
names to uniquely identify the IRQs and also to fix the above mentioned
issues.
Link: https://lore.kernel.org/linux-pci/20240828-pci-qcom-hotplug-v4-6-263a385fbbcb@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Current error message just prints the contents of PARF_INT_ALL_STATUS
register as if like the IRQ event number. It could mislead the users.
Reword it to make it clear that the error message is actually showing the
interrupt status register to help debug spurious IRQ events.
While at it, let's also switch over to dev_WARN_ONCE() so that any IRQ
storm won't flood the kernel log buffer.
Link: https://lore.kernel.org/linux-pci/20240828-pci-qcom-hotplug-v4-2-263a385fbbcb@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Once the events are disabled in PARF_INT_ALL_MASK register, only the
enabled events will generate global IRQ. So there is no need to do the
masking again in the IRQ handler, drop it.
If there are any spurious IRQs getting generated, they will be reported
using the existing dev_err() in the handler.
Link: https://lore.kernel.org/linux-pci/20240828-pci-qcom-hotplug-v4-1-263a385fbbcb@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
The ACSPCIE module is capable of driving the reference clock required by
the PCIe Endpoint device. It is an alternative to on-board and external
reference clock generators. Enabling the output from the ACSPCIE module's
PAD IO Buffers requires clearing the "PAD IO disable" bits of the
ACSPCIE_PROXY_CTRL register in the CTRL_MMR register space.
Add support to enable the ACSPCIE reference clock output using the optional
device-tree property "ti,syscon-acspcie-proxy-ctrl".
Link: https://lore.kernel.org/linux-pci/20240829105316.1483684-3-s-vadapalli@ti.com
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Add support for Xilinx QDMA Soft IP core as Root Port.
The Versal Prime devices support QDMA soft IP module in programmable logic.
The integrated QDMA Soft IP block has integrated bridge function that can
act as PCIe Root Port.
Link: https://lore.kernel.org/linux-pci/20240811022345.1178203-3-thippesw@amd.com
Signed-off-by: Thippeswamy Havalige <thippesw@amd.com>
[kwilczynski: removed unused header]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Add support for enabling/disabling PCIe PHYs. We can't really do
anything about failures in the disable/remove path, so just print an
error.
Link: https://lore.kernel.org/r/20240531161337.864994-7-sean.anderson@linux.dev
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The conditions logged by the misc interrupt can occur repeatedly and
continuously. Avoid rendering the console unusable by rate-limiting
these messages.
Link: https://lore.kernel.org/r/20240531161337.864994-5-sean.anderson@linux.dev
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
MSGF_LEG_MASK is laid out with INTA in bit 0, INTB in bit 1, INTC in bit 2,
and INTD in bit 3. Hardware IRQ numbers start at 0, and we register
PCI_NUM_INTX IRQs. So to enable INTA (aka hwirq 0) we should set bit 0.
Remove the subtraction of one.
This bug would cause INTx interrupts not to be delivered, as enabling INTB
would actually enable INTA, and enabling INTA wouldn't enable anything at
all. It is likely that this got overlooked for so long since most PCIe
hardware uses MSIs. This fixes the following UBSAN error:
UBSAN: shift-out-of-bounds in ../drivers/pci/controller/pcie-xilinx-nwl.c:389:11
shift exponent 18446744073709551615 is too large for 32-bit type 'int'
CPU: 1 PID: 61 Comm: kworker/u10:1 Not tainted 6.6.20+ #268
Hardware name: xlnx,zynqmp (DT)
Workqueue: events_unbound deferred_probe_work_func
Call trace:
dump_backtrace (arch/arm64/kernel/stacktrace.c:235)
show_stack (arch/arm64/kernel/stacktrace.c:242)
dump_stack_lvl (lib/dump_stack.c:107)
dump_stack (lib/dump_stack.c:114)
__ubsan_handle_shift_out_of_bounds (lib/ubsan.c:218 lib/ubsan.c:387)
nwl_unmask_leg_irq (drivers/pci/controller/pcie-xilinx-nwl.c:389 (discriminator 1))
irq_enable (kernel/irq/internals.h:234 kernel/irq/chip.c:170 kernel/irq/chip.c:439 kernel/irq/chip.c:432 kernel/irq/chip.c:345)
__irq_startup (kernel/irq/internals.h:239 kernel/irq/chip.c:180 kernel/irq/chip.c:250)
irq_startup (kernel/irq/chip.c:270)
__setup_irq (kernel/irq/manage.c:1800)
request_threaded_irq (kernel/irq/manage.c:2206)
pcie_pme_probe (include/linux/interrupt.h:168 drivers/pci/pcie/pme.c:348)
Fixes: 9a181e1093 ("PCI: xilinx-nwl: Modify IRQ chip for legacy interrupts")
Link: https://lore.kernel.org/r/20240531161337.864994-3-sean.anderson@linux.dev
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
With commit 5b6272e0ef ("PCI: qcom: Add OPP support to scale
performance"), OPP was used to control the interconnect and power domains
if the platform supported OPP. Also to maintain the backward compatibility
with platforms not supporting OPP but just ICC, the above mentioned commit
assumed that if ICC was not available on the platform, it would resort to
OPP.
Unfortunately, some old platforms don't support either ICC or OPP. On those
platforms, resorting to OPP in the absence of ICC throws below errors from
OPP core during suspend and resume:
qcom-pcie 1c08000.pcie: dev_pm_opp_set_opp: device opp doesn't exist
qcom-pcie 1c08000.pcie: _find_key: OPP table not found (-19)
Also, it doesn't make sense to invoke the OPP APIs when OPP is not
supported by the platform at all.
Add a "use_pm_opp" flag to identify whether OPP is supported and use it to
control invoking the OPP APIs.
Fixes: 5b6272e0ef ("PCI: qcom: Add OPP support to scale performance")
Link: https://lore.kernel.org/linux-pci/20240722131128.32470-1-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mayank Rana <quic_mrana@quicinc.com>
SA8775P SoC has support for the hardware parity check feature on the MHI
RAM (entity that holds MHI registers, etc.) But due to a hardware bug in
the parity check logic, the data parity error interrupt is getting
generated all the time when using MHI. So the hardware team has suggested
disabling the parity check error to work around the hardware bug.
Mask the parity error interrupt in PARF_INT_ALL_5_MASK register.
Fixes: 58d0d3e032 ("PCI: qcom-ep: Add support for SA8775P SOC")
Link: https://lore.kernel.org/linux-pci/20240808063057.7394-1-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This code accidentally uses && where || was intended. It potentially
results in a NULL dereference.
Thus, fix the if-statement expression to use the correct condition.
Fixes: 86f271f22b ("PCI: keystone: Add workaround for Errata #i2037 (AM65x SR 1.0)")
Link: https://lore.kernel.org/linux-pci/1b762a93-e1b2-4af3-8c04-c8843905c279@stanley.mountain
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Use MSI_FLAG_NO_AFFINITY, which keeps .irq_set_affinity() unset and allows
migrate_one_irq() to exit right away, without warnings like this:
IRQ...: set affinity failed(-22)
Remove the .irq_set_affinity() implementation that is no longer needed.
Link: https://lore.kernel.org/r/20240723132958.41320-16-marek.vasut+renesas@mailbox.org
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Use MSI_FLAG_NO_AFFINITY, which keeps .irq_set_affinity() unset and allows
migrate_one_irq() to exit right away, without warnings like this:
IRQ...: set affinity failed(-22)
Remove the .irq_set_affinity() implementation that is no longer needed.
Link: https://lore.kernel.org/r/20240723132958.41320-15-marek.vasut+renesas@mailbox.org
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Use MSI_FLAG_NO_AFFINITY, which keeps .irq_set_affinity() unset and allows
migrate_one_irq() to exit right away, without warnings like this:
IRQ...: set affinity failed(-22)
Remove the .irq_set_affinity() implementation that is no longer needed.
Link: https://lore.kernel.org/r/20240723132958.41320-14-marek.vasut+renesas@mailbox.org
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Use MSI_FLAG_NO_AFFINITY, which keeps .irq_set_affinity() unset and allows
migrate_one_irq() to exit right away, without warnings like this:
IRQ...: set affinity failed(-22)
Remove the .irq_set_affinity() implementation that is no longer needed.
Link: https://lore.kernel.org/r/20240723132958.41320-13-marek.vasut+renesas@mailbox.org
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Nirmal Patel <nirmal.patel@linux.intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Use MSI_FLAG_NO_AFFINITY, which keeps .irq_set_affinity() unset and allows
migrate_one_irq() to exit right away, without warnings like this:
IRQ...: set affinity failed(-22)
Remove the .irq_set_affinity() implementation that is no longer needed.
Link: https://lore.kernel.org/r/20240723132958.41320-12-marek.vasut+renesas@mailbox.org
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Use MSI_FLAG_NO_AFFINITY, which keeps .irq_set_affinity() unset and allows
migrate_one_irq() to exit right away, without warnings like this:
IRQ...: set affinity failed(-22)
Remove the .irq_set_affinity() implementation that is no longer needed.
Link: https://lore.kernel.org/r/20240723132958.41320-11-marek.vasut+renesas@mailbox.org
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Use MSI_FLAG_NO_AFFINITY, which keeps .irq_set_affinity() unset and allows
migrate_one_irq() to exit right away, without warnings like this:
IRQ...: set affinity failed(-22)
Remove the .irq_set_affinity() implementation that is no longer needed.
Link: https://lore.kernel.org/r/20240723132958.41320-10-marek.vasut+renesas@mailbox.org
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Use MSI_FLAG_NO_AFFINITY, which keeps .irq_set_affinity() unset and allows
migrate_one_irq() to exit right away, without warnings like this:
IRQ...: set affinity failed(-22)
Remove the .irq_set_affinity() implementation that is no longer needed.
Link: https://lore.kernel.org/r/20240723132958.41320-9-marek.vasut+renesas@mailbox.org
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Use MSI_FLAG_NO_AFFINITY, which keeps .irq_set_affinity() unset and allows
migrate_one_irq() to exit right away, without warnings like this:
IRQ...: set affinity failed(-22)
Remove the .irq_set_affinity() implementation that is no longer needed.
Link: https://lore.kernel.org/r/20240723132958.41320-8-marek.vasut+renesas@mailbox.org
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Jianjun Wang <jianjun.wang@mediatek.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Use MSI_FLAG_NO_AFFINITY, which keeps .irq_set_affinity() unset and allows
migrate_one_irq() to exit right away, without warnings like this:
IRQ...: set affinity failed(-22)
Remove the .irq_set_affinity() implementation that is no longer needed.
Link: https://lore.kernel.org/r/20240723132958.41320-7-marek.vasut+renesas@mailbox.org
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Jianjun Wang <jianjun.wang@mediatek.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Use MSI_FLAG_NO_AFFINITY, which keeps .irq_set_affinity() unset and allows
migrate_one_irq() to exit right away, without warnings like this:
IRQ...: set affinity failed(-22)
Remove the .irq_set_affinity() implementation that is no longer needed.
Link: https://lore.kernel.org/r/20240723132958.41320-6-marek.vasut+renesas@mailbox.org
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Use MSI_FLAG_NO_AFFINITY, which keeps .irq_set_affinity() unset and allows
migrate_one_irq() to exit right away, without warnings like this:
IRQ...: set affinity failed(-22)
Remove the .irq_set_affinity() implementation that is no longer needed.
Link: https://lore.kernel.org/r/20240723132958.41320-5-marek.vasut+renesas@mailbox.org
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Use MSI_FLAG_NO_AFFINITY, which keeps .irq_set_affinity() unset and allows
migrate_one_irq() to exit right away, without warnings like this:
IRQ...: set affinity failed(-22)
Remove the .irq_set_affinity() implementation that is no longer needed.
Link: https://lore.kernel.org/r/20240723132958.41320-4-marek.vasut+renesas@mailbox.org
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Use MSI_FLAG_NO_AFFINITY, which keeps .irq_set_affinity() unset and allows
migrate_one_irq() to exit right away, without warnings like this:
IRQ...: set affinity failed(-22)
Remove the .irq_set_affinity() implementation that is no longer needed.
Link: https://lore.kernel.org/r/20240723132958.41320-3-marek.vasut+renesas@mailbox.org
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
- Remove unused struct 'acpi_handle_node' (Dr. David Alan Gilbert)
- Use array notation for portdrv .id_table consistently (Masahiro Yamada)
- Switch to new Intel CPU model defines (Tony Luck)
- Add missing MODULE_DESCRIPTION() macros (Jeff Johnson)
* pci/misc:
PCI: controller: Add missing MODULE_DESCRIPTION() macros
PCI: Add missing MODULE_DESCRIPTION() macros
PCI/PM: Switch to new Intel CPU model defines
PCI: Use array for .id_table consistently
ACPI: PCI: Remove unused struct 'acpi_handle_node'
- Create "domain" symlink for vmd before adding devices below the VMD
bridge so it's available when mdadm assembles RAID devices from them
(Jiwei Sun)
* pci/controller/vmd:
PCI: vmd: Create domain symlink before pci_bus_add_devices()
- Ensure Tegra194 and Tegra234 inbound ATU entries are 64KB-aligned to
match the hardware restriction (Jon Hunter)
- Remove unused struct 'tegra_pcie_soc' (Dr. David Alan Gilbert)
* pci/controller/tegra194:
PCI: tegra: Remove unused struct 'tegra_pcie_soc'
PCI: tegra194: Set EP alignment restriction for inbound ATU
- Use dev_err_probe() in dw-rockchip probe error path so the failures
aren't silent (Uwe Kleine-König)
- Sleep PCIE_T_PVPERL_MS (100ms) before deasserting PERST# (Damien Le Moal)
- Sleep PCIE_T_RRS_READY_MS (100ms) after conventional reset, before a
config access (Damien Le Moal)
- Request the PERST# GPIO with GPIOD_OUT_LOW so it matches the POR value,
which avoids a spurious PERST# assertion and fixes a Qcom modem firmware
crash and issues with WLAN controllers, e.g., RTL8822CE (Manivannan
Sadhasivam for rockchip, Niklas Cassel for dw-rockchip)
- Refactor dw-rockchip and add support for Endpoint mode for rk3568 and
rk3588 (Niklas Cassel)
* pci/controller/rockchip:
PCI: dw-rockchip: Use pci_epc_init_notify() directly
PCI: dw-rockchip: Add endpoint mode support
PCI: dw-rockchip: Refactor the driver to prepare for EP mode
PCI: dw-rockchip: Add rockchip_pcie_get_ltssm() helper
PCI: dw-rockchip: Fix weird indentation
PCI: dw-rockchip: Fix initial PERST# GPIO value
PCI: dw-rockchip: Add error messages in .probe() error paths
PCI: rockchip: Use GPIOD_OUT_LOW flag while requesting ep_gpio
PCI: rockchip-host: Wait 100ms after reset before starting configuration
PCI: rockchip-host: Fix rockchip_pcie_host_init_port() PERST# handling
- Add Synopsys DWC macros for lane skew configuration (Yoshihiro Shimoda)
- Add struct rcar_gen4_pcie_drvdata to provide for future SoCs with
different initialization requirements (Yoshihiro Shimoda)
- Add .ltssm_control() method for SoC dependencies (Yoshihiro Shimoda)
- Add r8a779g0 (R-Car V4H) support (Yoshihiro Shimoda)
* pci/controller/rcar-gen4:
PCI: rcar-gen4: Add support for R-Car V4H
PCI: rcar-gen4: Add .ltssm_control() for other SoC support
PCI: rcar-gen4: Add struct rcar_gen4_pcie_drvdata
PCI: dwc: Add PCIE_PORT_{FORCE,LANE_SKEW} macros
- Demote WARN() to dev_warn_ratelimited() in rcar_pcie_wakeup() to avoid
excessive warnings when the driver is confused about link state when
resuming (Marek Vasut)
* pci/controller/rcar:
PCI: rcar: Demote WARN() to dev_warn_ratelimited() in rcar_pcie_wakeup()
- Use devm_clk_bulk_get_all() to get all the clocks from DT to avoid
writing out all the clock names (Manivannan Sadhasivam)
- Add DT binding and driver support for the SA8775P SoC (Mrinmay Sarkar)
- Refactor dw_pcie_edma_find_chip() to enable adding support for Hyper DMA
(HDMA) (Manivannan Sadhasivam)
- Enable drivers to supply the eDMA channel count since some can't auto
detect this (Manivannan Sadhasivam)
- Add HDMA support for the SA8775P SoC (Mrinmay Sarkar)
- Override the SA8775P NO_SNOOP default to avoid possible memory corruption
(Mrinmay Sarkar)
- Make sure resources are disabled during PERST# assertion, even if the
link is already disabled (Manivannan Sadhasivam)
- Vote for the CPU-PCIe ICC (interconnect) path to ensure it stays active
even if other drivers don't vote for it (Krishna chaitanya chundru)
- Add Operating Performance Points (OPP) to scale performance state based
on aggregate link bandwidth to improve SoC power efficiency (Krishna
chaitanya chundru)
- Return failure instead of success if dev_pm_opp_find_freq_floor() fails
(Dan Carpenter)
- Avoid an error pointer dereference if dev_pm_opp_find_freq_exact() fails
(Dan Carpenter)
- Prevent use of uninitialized data in qcom_pcie_suspend_noirq() (Dan
Carpenter)
* pci/controller/qcom:
PCI: qcom: Prevent use of uninitialized data in qcom_pcie_suspend_noirq()
PCI: qcom: Prevent potential error pointer dereference
PCI: qcom: Fix missing error code in qcom_pcie_probe()
PCI: qcom: Add OPP support to scale performance
PCI: Bring the PCIe speed to MBps logic to new pcie_dev_speed_mbps()
PCI: qcom: Add ICC bandwidth vote for CPU to PCIe path
PCI: qcom-ep: Disable resources unconditionally during PERST# assert
PCI: qcom-ep: Override NO_SNOOP attribute for SA8775P EP
PCI: qcom: Override NO_SNOOP attribute for SA8775P RC
PCI: epf-mhi: Enable HDMA for SA8775P SoC
PCI: qcom-ep: Add HDMA support for SA8775P SoC
PCI: dwc: Pass the eDMA mapping format flag directly from glue drivers
PCI: dwc: Skip finding eDMA channels count for HDMA platforms
PCI: dwc: Refactor dw_pcie_edma_find_chip() API
PCI: qcom-ep: Add support for SA8775P SOC
dt-bindings: PCI: qcom-ep: Add support for SA8775P SoC
PCI: qcom: Use devm_clk_bulk_get_all() API
- Move PLDA XpressRICH generic DT binding properties to
plda,xpressrich3-axi-common.yaml where they can be shared across
PLDA-based drivers (Minda Chen)
- Create a drivers/pci/controller/plda/ directory for PLDA-based drivers
and move pcie-microchip-host.c there (Minda Chen)
- Move PLDA generic macros to pcie-plda.h where they can be shared across
drivers (Minda Chen)
- Extract PLDA generic structures from pcie-microchip-host.c, rename them
to be generic, and move them to pcie-plda-host.c where they can be shared
across drivers (Minda Chen)
- Add a .request_event_irq() callback for requesting device-specific
interrupts in addition to PLDA-generic interrupts (Minda Chen)
- Add DT binding and driver for the StarFive JH7110 SoC, based on PLDA IP
(Minda Chen)
* pci/controller/microchip:
PCI: starfive: Add JH7110 PCIe controller
dt-bindings: PCI: Add StarFive JH7110 PCIe controller
PCI: Add PCIE_RESET_CONFIG_DEVICE_WAIT_MS waiting time value
PCI: plda: Pass pci_host_bridge to plda_pcie_setup_iomems()
PCI: plda: Add host init/deinit and map bus functions
PCI: plda: Add event bitmap field to struct plda_pcie_rp
PCI: microchip: Move IRQ functions to pcie-plda-host.c
PCI: microchip: Add event irqchip field to host port and add PLDA irqchip
PCI: microchip: Add get_events() callback and PLDA get_event()
PCI: microchip: Add INTx and MSI event num to struct plda_event
PCI: microchip: Add request_event_irq() callback function
PCI: microchip: Add num_events field to struct plda_pcie_rp
PCI: microchip: Rename interrupt related functions
PCI: microchip: Move PLDA functions to pcie-plda-host.c
PCI: microchip: Rename PLDA functions to be generic
PCI: microchip: Move PLDA structures to plda-pcie.h
PCI: microchip: Rename PLDA structures to be generic
PCI: microchip: Add bridge_addr field to struct mc_pcie
PCI: microchip: Move PLDA IP register macros to pcie-plda.h
PCI: microchip: Move pcie-microchip-host.c to PLDA directory
dt-bindings: PCI: Add PLDA XpressRICH PCIe host common properties
# Conflicts:
# drivers/pci/pci.h
- Enable BAR 0 only for v3.65a to avoid Completion Timeouts that
cause a 45 second boot delay on the v4.90a-based AM654x SoC (Siddharth
Vadapalli)
- Avoid a NULL pointer dereference if DT failed to provide a host bridge
memory window (Aleksandr Mishin)
* pci/controller/keystone:
PCI: keystone: Add workaround for Errata #i2037 (AM65x SR 1.0)
PCI: keystone: Fix NULL pointer dereference in case of DT error in ks_pcie_setup_rc_app_regs()
PCI: keystone: Don't enable BAR 0 for AM654x
PCI: keystone: Relocate ks_pcie_set/clear_dbi_mode()
- Return zero, not garbage, when reading PCI_INTERRUPT_PIN from a Hyper-V
device (Wei Liu)
* pci/controller/hyperv:
PCI: hv: Return zero, not garbage, when reading PCI_INTERRUPT_PIN
- Correct the dra7xx_pcie_cpu_addr_fixup() parameter name, which takes a
CPU address but called it "pci_addr" (Niklas Cassel)
* pci/controller/dra7xx:
PCI: dra7xx: Fix dra7xx_pcie_cpu_addr_fixup() parameter name
- Correct the artpec6_pcie_cpu_addr_fixup() parameter name, which takes a
CPU address but called it "pci_addr" (Niklas Cassel)
* pci/controller/artpec6:
PCI: artpec6: Fix artpec6_pcie_cpu_addr_fixup() parameter name
- Check IORESOURCE_BUS existence to avoid NULL pointer dereference
(Aleksandr Mishin)
* pci/controller/al:
PCI: al: Check IORESOURCE_BUS existence during probe
- Use msleep() in DWC core instead of usleep_range() for ~100 ms sleep
(Konrad Dybcio)
- Fix iATU slot management to avoid using the wrong slot after PERST#
assert/deassert, which could potentially cause DMA to go the wrong place
(Frank Li)
- Consolidate dw_pcie_prog_outbound_atu() arguments into a struct to ease
adding new functionality like initiating Message TLPs (Yoshihiro Shimoda)
- Add support for endpoints to initiate PCIe messages (Yoshihiro Shimoda)
- Add #defines for PCIe INTx messages (Yoshihiro Shimoda)
- Add support for endpoints to initiate PCIe PME_Turn_Off messages for
system suspend (Frank Li)
- Add dw_pcie_ep_linkdown() to reinitialize registers that are lost when
the link goes down (Manivannan Sadhasivam)
- Use dw_pcie_ep_linkdown() to reinitialize qcom non-sticky registers that
are lost when the link goes down (Manivannan Sadhasivam)
- Enforce DWC limitation that 64-bit BARs must start with the even numbered
BAR (Niklas Cassel)
* pci/controller/dwc:
PCI: dwc: ep: Enforce DWC specific 64-bit BAR limitation
PCI: layerscape-ep: Use the generic dw_pcie_ep_linkdown() API to handle Link Down event
PCI: qcom-ep: Use the generic dw_pcie_ep_linkdown() API to handle Link Down event
PCI: dwc: ep: Remove dw_pcie_ep_init_notify() wrapper
PCI: dwc: ep: Add a generic dw_pcie_ep_linkdown() API to handle Link Down event
PCI: dwc: Add generic MSG TLP support for sending PME_Turn_Off when system suspend
PCI: Add PCIE_MSG_CODE_PME_TURN_OFF message macro
PCI: Add PCIE_MSG_CODE_ASSERT_INTx message macros
PCI: dwc: Add outbound MSG TLPs support
PCI: dwc: Consolidate args of dw_pcie_prog_outbound_atu() into a structure
PCI: dwc: Fix index 0 incorrectly being interpreted as a free ATU slot
PCI: dwc: Use msleep() in dw_pcie_wait_for_link()
- Include <linux/irqchip/chained_irq.h> in dra7xx to avoid implicitly
including it elsewhere (Andy Shevchenko)
- Remove unused <linux/of_gpio.h> from aardvark and dwc drivers (dra7xx,
meson, qcom, tegra194) (Andy Shevchenko)
- Convert kirin to use scoped for_each_available_child_of_node() to ease
future error exits (Javier Carrasco)
- Convert imx6 and kirin to use the agnostic GPIO API to simplify GPIO
setup and remove usage of the deprecated of_gpio.h API (Andy Shevchenko)
* pci/controller/gpio:
PCI: kirin: Convert to use agnostic GPIO API
PCI: kirin: Convert kirin_pcie_parse_port() to scoped iterator
PCI: imx6: Convert to use agnostic GPIO API
PCI: dwc: Remove unused of_gpio.h inclusion
PCI: aardvark: Remove unused of_gpio.h inclusion
PCI: dra7xx: Add missing chained IRQ header inclusion
- Remove unused struct pci_epf_group.type_group (Christophe JAILLET)
- Use cached epc_features instead of pci_epc_get_features() to avoid having
to check for failure (potential NULL pointer dereference) (Manivannan
Sadhasivam)
- Drop pointless local msix_capable variable in pci_epf_test_alloc_space()
(Manivannan Sadhasivam)
- Rename struct pci_epc_event_ops.core_init to .epc_init, since "core" is
no longer meaningful here (Manivannan Sadhasivam)
- Rename pci_epc_bme_notify(), pci_epf_mhi_bme(), pci_epc_bme_notify() to
spell out "bus_master_enable" instead of "bme" (Manivannan Sadhasivam)
- Factor pci_epf_test_clear_bar() and pci_epf_test_free_space() out of
pci_epf_test_unbind() so they can be reused elsewhere (Manivannan
Sadhasivam)
- Move DMA initialization to the pci_epf_mhi_epc_init() callback so
endpoint drivers do this uniformly (Manivannan Sadhasivam)
- Add endpoint testing for Link Down events (Manivannan Sadhasivam)
- Add 'epc_deinit' event so endpoints that can be reset via PERST# (qcom,
tegra194) can notify EPF drivers when this happens (Manivannan
Sadhasivam)
- Make pci_epc_class constant (Greg Kroah-Hartman)
- Fix vpci_scan_bus() error checking to print error for failure (not
success) and clean up after failure (Dan Carpenter)
- Fix epf_ntb_epc_cleanup() error handling to clean up scratchpad BARs and
clean up in mirror order of allocation (Dan Carpenter)
- Add rk3588, which requires 64KB BAR alignment, to pci_endpoint_test
(Niklas Cassel)
- Use memcpy_toio()/memcpy_fromio() for endpoint BAR tests to improve
performance (Niklas Cassel)
- Set DMA mask to 48 bits always to simplify endpoint test, since there's
there's no need to check for error or to fallback to 32 bits (Frank Li)
- Suggest using programmable Vendor/Device ID (when supported) to use
pci_endpoint_test without having to add new entries (Yoshihiro Shimoda)
- Remove unused pci_endpoint_test_bar_{readl,writel}() (Jiapeng Chong)
- Remove 'linkup' and add 'add_cfs' to the endpoint function driver 'ops'
documentation to match the code (Alexander Stein)
-
* pci/endpoint:
Documentation: PCI: pci-endpoint: Fix EPF ops list
misc: pci_endpoint_test: Remove unused pci_endpoint_test_bar_{readl,writel} functions
misc: pci_endpoint_test: Document policy about adding pci_device_id
misc: pci_endpoint_test: Refactor dma_set_mask_and_coherent() logic
misc: pci_endpoint_test: Use memcpy_toio()/memcpy_fromio() for BAR tests
misc: pci_endpoint_test: Add support for Rockchip rk3588
PCI: endpoint: Fix error handling in epf_ntb_epc_cleanup()
PCI: endpoint: Clean up error handling in vpci_scan_bus()
PCI: endpoint: Make pci_epc_class struct constant
PCI: endpoint: Introduce 'epc_deinit' event and notify the EPF drivers
PCI: endpoint: pci-epf-test: Handle Link Down event
PCI: endpoint: pci-epf-{mhi/test}: Move DMA initialization to EPC init callback
PCI: endpoint: pci-epf-test: Refactor pci_epf_test_unbind() function
PCI: endpoint: Rename BME to Bus Master Enable
PCI: endpoint: Rename core_init() callback in 'struct pci_epc_event_ops' to epc_init()
PCI: endpoint: pci-epf-test: Use 'msix_capable' flag directly in pci_epf_test_alloc_space()
PCI: endpoint: pci-epf-test: Make use of cached 'epc_features' in pci_epf_test_core_init()
PCI: endpoint: Remove unused field in struct pci_epf_group
The LS7A chipset can be used as part of a PCIe Root Complex with
Loongson-3C6000 and similar CPUs. In this case, DEV_LS7A_PCIE_PORT5 has a
PCI_CLASS_BRIDGE_HOST class code, and it is a Type 0 Function whose config
space provides access to Root Complex registers.
The DEV_LS7A_PCIE_PORT5 has an MSI Capability, and its MSI Enable bit must
be set before other devices below the Root Complex can use MSI. This is
not the standard PCI behavior of MSI Enable, so the normal PCI MSI code
does not set it.
Set the DEV_LS7A_PCIE_PORT5 MSI Enable bit via a quirk so other devices
below the Root Complex can use MSI.
[kwilczynski: exit early to reduce indentation; commit log]
Link: https://lore.kernel.org/linux-pci/20240612065315.2048110-1-chenhuacai@loongson.cn
Signed-off-by: Sheng Wu <wusheng@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
The vmd driver creates a "domain" symlink in sysfs for each VMD bridge.
Previously this symlink was created after pci_bus_add_devices() added
devices below the VMD bridge and emitted udev events to announce them to
userspace.
This led to a race between userspace consumers of the udev events and the
kernel creation of the symlink. One such consumer is mdadm, which
assembles block devices into a RAID array, and for devices below a VMD
bridge, mdadm depends on the "domain" symlink.
If mdadm loses the race, it may be unable to assemble a RAID array, which
may cause a boot failure or other issues, with complaints like this:
(udev-worker)[2149]: nvme1n1: '/sbin/mdadm -I /dev/nvme1n1'(err) 'mdadm: Unable to get real path for '/sys/bus/pci/drivers/vmd/0000:c7:00.5/domain/device''
(udev-worker)[2149]: nvme1n1: '/sbin/mdadm -I /dev/nvme1n1'(err) 'mdadm: /dev/nvme1n1 is not attached to Intel(R) RAID controller.'
(udev-worker)[2149]: nvme1n1: '/sbin/mdadm -I /dev/nvme1n1'(err) 'mdadm: No OROM/EFI properties for /dev/nvme1n1'
(udev-worker)[2149]: nvme1n1: '/sbin/mdadm -I /dev/nvme1n1'(err) 'mdadm: no RAID superblock on /dev/nvme1n1.'
(udev-worker)[2149]: nvme1n1: Process '/sbin/mdadm -I /dev/nvme1n1' failed with exit code 1.
This symptom prevents the OS from booting successfully.
After a NVMe disk is probed/added by the nvme driver, udevd invokes mdadm
to detect if there is a mdraid associated with this NVMe disk, and mdadm
determines if a NVMe device is connected to a particular VMD domain by
checking the "domain" symlink. For example:
Thread A Thread B Thread mdadm
vmd_enable_domain
pci_bus_add_devices
__driver_probe_device
...
work_on_cpu
schedule_work_on
: wakeup Thread B
nvme_probe
: wakeup scan_work
to scan nvme disk
and add nvme disk
then wakeup udevd
: udevd executes
mdadm command
flush_work main
: wait for nvme_probe done ...
__driver_probe_device find_driver_devices
: probe next nvme device : 1) Detect domain symlink
... 2) Find domain symlink
... from vmd sysfs
... 3) Domain symlink not
... created yet; failed
sysfs_create_link
: create domain symlink
Create the VMD "domain" symlink before invoking pci_bus_add_devices() to
avoid this race.
Suggested-by: Adrian Huang <ahuang12@lenovo.com>
Link: https://lore.kernel.org/linux-pci/20240605124844.24293-1-sjiwei@163.com
Signed-off-by: Jiwei Sun <sunjw10@lenovo.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Nirmal Patel <nirmal.patel@linux.intel.com>
Smatch complains that "ret" could be uninitialized if "pcie->icc_mem" is
NULL and "pm_suspend_target_state == PM_SUSPEND_MEM".
Silence this warning by initializing ret to zero.
Fixes: 78b5f6f8855e ("PCI: qcom: Add OPP support to scale performance")
Link: https://lore.kernel.org/linux-pci/20240708180539.1447307-4-dan.carpenter@linaro.org
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Anders Roxell <anders.roxell@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Only call dev_pm_opp_put() if dev_pm_opp_find_freq_exact() succeeds;
otherwise it leads to an error pointer dereference.
Fixes: 78b5f6f8855e ("PCI: qcom: Add OPP support to scale performance")
Link: https://lore.kernel.org/linux-pci/20240708180539.1447307-3-dan.carpenter@linaro.org
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Anders Roxell <anders.roxell@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
A previous commit ("PCI: dwc: ep: Remove dw_pcie_ep_init_notify() wrapper")
removed the dw_pcie_ep_init_notify() wrapper and changed the DWC glue
drivers to instead use pci_epc_init_notify() directly.
The endpoint support for the dw-rockchip had not been merged at that point
in time, so the previous commit wrapper") did not update dw-rockchip.
Do the same change for dw-rockchip, so that the driver will not try
to use a function that has now been removed.
Link: https://lore.kernel.org/linux-pci/20240622132024.2927799-2-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCIe controller in rk3568 and rk3588 can operate in endpoint mode.
This endpoint mode support heavily leverages the existing code in
pcie-designware-ep.c.
Add support for endpoint mode to the existing pcie-dw-rockchip glue
driver.
[kwilczynski: squash with patch adding the PCI_ENDPOINT dependency]
Link: https://lore.kernel.org/linux-pci/20240607-rockchip-pcie-ep-v1-v5-10-0a042d6b0049@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Refactor the driver to prepare for EP mode.
Add of-match data to the existing compatible, and explicitly define it as
DW_PCIE_RC_TYPE. This way, we will be able to add EP mode in a follow-up
commit in a much less intrusive way, which makes the follow-up commit much
easier to review.
No functional change intended.
Link: https://lore.kernel.org/linux-pci/20240607-rockchip-pcie-ep-v1-v5-9-0a042d6b0049@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Add a rockchip_pcie_ltssm() helper function that reads the LTSSM status.
This helper will be used in additional places in follow-up commits.
Link: https://lore.kernel.org/linux-pci/20240607-rockchip-pcie-ep-v1-v5-8-0a042d6b0049@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Fix the indentation of rockchip_pcie_{readl,writel}_apb() parameters to
match the opening parenthesis.
Link: https://lore.kernel.org/linux-pci/20240607-rockchip-pcie-ep-v1-v5-7-0a042d6b0049@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
PERST# is active low according to the PCIe specification.
However, the existing pcie-dw-rockchip.c driver does:
gpiod_set_value(..., 0); msleep(100); gpiod_set_value(..., 1);
when asserting + deasserting PERST#.
This is of course wrong, but because all the device trees for this
compatible string have also incorrectly marked this GPIO as ACTIVE_HIGH:
$ git grep -B 10 reset-gpios arch/arm64/boot/dts/rockchip/rk3568*
$ git grep -B 10 reset-gpios arch/arm64/boot/dts/rockchip/rk3588*
The actual toggling of PERST# is correct, and we cannot change it anyway,
since that would break device tree compatibility.
However, this driver does request the GPIO to be initialized as
GPIOD_OUT_HIGH, which does cause a silly sequence where PERST# gets
toggled back and forth for no good reason.
Fix this by requesting the GPIO to be initialized as GPIOD_OUT_LOW (which
for this driver means PERST# asserted).
This will avoid an unnecessary signal change where PERST# gets deasserted
(by devm_gpiod_get_optional()) and then gets asserted (by
rockchip_pcie_start_link()) just a few instructions later.
Before patch, debug prints on EP side, when booting RC:
[ 845.606810] pci: PERST# asserted by host!
[ 852.483985] pci: PERST# de-asserted by host!
[ 852.503041] pci: PERST# asserted by host!
[ 852.610318] pci: PERST# de-asserted by host!
After patch, debug prints on EP side, when booting RC:
[ 125.107921] pci: PERST# asserted by host!
[ 132.111429] pci: PERST# de-asserted by host!
This extra, very short, PERST# assertion + deassertion has been reported to
cause issues with certain WLAN controllers, e.g. RTL8822CE.
Fixes: 0e898eb8df ("PCI: rockchip-dwc: Add Rockchip RK356X host controller driver")
Link: https://lore.kernel.org/linux-pci/20240417164227.398901-1-cassel@kernel.org
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Jianfeng Liu <liujianfeng1994@gmail.com>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: stable@vger.kernel.org # v5.15+
Drivers that silently fail to probe provide a bad user experience and
make it unnecessarily hard to debug such a failure.
Fix it by using dev_err_probe() instead of a plain return.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240227141256.413055-2-ukleinek@debian.org
Signed-off-by: Uwe Kleine-König <ukleinek@debian.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Jesper Nilsson <jesper.nilsson@axis.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Rockchip platforms use 'GPIO_ACTIVE_HIGH' flag in the devicetree definition
for ep_gpio. This means, whatever the logical value set by the driver for
the ep_gpio, physical line will output the same logic level.
For instance,
gpiod_set_value_cansleep(rockchip->ep_gpio, 0); --> Level low
gpiod_set_value_cansleep(rockchip->ep_gpio, 1); --> Level high
But while requesting the ep_gpio, GPIOD_OUT_HIGH flag is currently used.
Now, this also causes the physical line to output 'high' creating trouble
for endpoint devices during host reboot.
When host reboot happens, the ep_gpio will initially output 'low' due to
the GPIO getting reset to its POR value. Then during host controller probe,
it will output 'high' due to GPIOD_OUT_HIGH flag. Then during
rockchip_pcie_host_init_port(), it will first output 'low' and then 'high'
indicating the completion of controller initialization.
On the endpoint side, each output 'low' of ep_gpio is accounted for PERST#
assert and 'high' for PERST# deassert. With the above mentioned flow during
host reboot, endpoint will witness below state changes for PERST#:
(1) PERST# assert - GPIO POR state
(2) PERST# deassert - GPIOD_OUT_HIGH while requesting GPIO
(3) PERST# assert - rockchip_pcie_host_init_port()
(4) PERST# deassert - rockchip_pcie_host_init_port()
Now the time interval between (2) and (3) is very short as both happen
during the driver probe(), and this results in a race in the endpoint.
Because, before completing the PERST# deassertion in (2), endpoint got
another PERST# assert in (3).
A proper way to fix this issue is to change the GPIOD_OUT_HIGH flag in (2)
to GPIOD_OUT_LOW. Because the usual convention is to request the GPIO with
a state corresponding to its 'initial/default' value and let the driver
change the state of the GPIO when required.
As per that, the ep_gpio should be requested with GPIOD_OUT_LOW as it
corresponds to the POR value of '0' (PERST# assert in the endpoint). Then
the driver can change the state of the ep_gpio later in
rockchip_pcie_host_init_port() as per the initialization sequence.
This fixes the firmware crash issue in Qcom based modems connected to
Rockpro64 based board.
Fixes: e77f847df5 ("PCI: rockchip: Add Rockchip PCIe controller support")
Closes: https://lore.kernel.org/mhi/20240402045647.GG2933@thinkpad/
Link: https://lore.kernel.org/linux-pci/20240416-pci-rockchip-perst-fix-v1-1-4800b1d4d954@linaro.org
Reported-by: Slark Xiao <slark_xiao@163.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Cc: stable@vger.kernel.org # v4.9
PCIe r6.0, sec 6.6.1, states that the host should wait for at least 100
msec from the end of a conventional reset (PERST# is de-asserted) before
sending a configuration request to ensure that the device is able to
respond with a "Request Retry Status" completion.
Add the PCIE_T_RRS_READY_MS macro to define this wait time and modify
rockchip_pcie_host_init_port() to add this 100ms sleep after deasserting
PERST# using the ep_gpio GPIO.
Link: https://lore.kernel.org/linux-pci/20240413004120.1099089-3-dlemoal@kernel.org
Suggested-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
PCIe CEM r5.1, sec 2.9.2, mandates that the PERST# signal must remain
asserted for at least 100 usec (Tperst-clk) after the PCIe reference clock
becomes stable (if a reference clock is supplied), and for at least 100
msec after the power is stable (Tpvperl, defined by the macro
PCIE_T_PVPERL_MS).
Modify rockchip_pcie_host_init_port() to satisfy these constraints by
adding a sleep period before deasserting PERST# using the ep_gpio GPIO.
Since Tperst-clk is the shorter wait time, add an msleep() call for the
longer PCIE_T_PVPERL_MS milliseconds to handle both timing requirements.
Link: https://lore.kernel.org/linux-pci/20240413004120.1099089-2-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
From the DWC EP databook 5.96a, section "3.5.7.1.4 General Rules for BAR
Setup (Fixed Mask or Programmable Mask Schemes Only)":
"Any pair (for example BARs 0 and 1) can be configured as one 64-bit BAR,
two 32-bit BARs, or one 32-bit BAR."
"BAR pairs cannot overlap to form a 64-bit BAR. For example, you cannot
combine BARs 1 and 2 to form a 64-bit BAR."
While this limitation does exist in some other PCI endpoint controllers,
e.g. cdns_pcie_ep_set_bar(), the limitation does not appear to be defined
in the PCIe specification itself, thus add an explicit check for this in
dw_pcie_ep_set_bar() (rather than pci_epc_set_bar()).
Link: https://lore.kernel.org/linux-pci/20240528134839.8817-2-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Now that dw_pcie_ep_linkdown() is available, use it. This also handles the
reinitialization of DWC non-sticky registers in addition to sending the
notification to EPF drivers.
Closes: https://lore.kernel.org/linux-pci/20240528195539.GA458945@bhelgaas
Link: https://lore.kernel.org/linux-pci/20240606-pci-deinit-v1-5-4395534520dc@linaro.org
Reported-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Now that the generic dw_pcie_ep_linkdown() API is available, use it. This
also handles the reinitialization of DWC non-sticky registers in addition
to sending the notification to EPF drivers.
Link: https://lore.kernel.org/linux-pci/20240430-pci-epf-rework-v4-9-22832d0d456f@linaro.org
Tested-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Currently dw_pcie_ep_init_notify() wrapper just calls pci_epc_init_notify()
directly, so this wrapper provides no benefit to the glue drivers.
Remove it and call pci_epc_init_notify() directly from glue drivers.
Suggested-by: Bjorn Helgaas <helgaas@kernel.org>
Link: https://lore.kernel.org/linux-pci/20240606-pci-deinit-v1-1-4395534520dc@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Per PCIe r6.0, sec 5.2, a Link Down event can happen under any of the
following circumstances:
1. Fundamental/Hot reset
2. Link disable transmission by upstream component
3. Moving from L2/L3 to L0
In those cases, Link Down causes some non-sticky DWC registers to lose the
state (like REBAR, etc.), so drivers need to reinitialize them to function
properly once the link comes back again.
This is not a problem for drivers supporting PERST# IRQ, since they can
reinitialize the registers in the PERST# IRQ callback. But for the drivers
not supporting PERST#, there is no way they can reinitialize the registers
other than relying on Link Down IRQ received when the link goes down. So
add a DWC generic API dw_pcie_ep_linkdown() that reinitializes the
non-sticky registers and also notifies the EPF drivers about link going
down.
This API can also be used by the drivers supporting PERST# to handle the
scenario (2) mentioned above.
NOTE: For the sake of code organization, move the dw_pcie_ep_linkup()
definition just above dw_pcie_ep_linkdown().
Link: https://lore.kernel.org/linux-pci/20240430-pci-epf-rework-v4-8-22832d0d456f@linaro.org
Tested-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: update spec citation]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Instead of relying on the vendor specific implementations to send the
PME_Turn_Off message, introduce a generic way of sending the message using
the MSG TLP.
This is achieved by reserving a region for MSG TLP of size
'pci->region_align', at the end of the first IORESOURCE_MEM window of the
host bridge. And then sending the PME_Turn_Off message during system
suspend with the help of iATU.
The reason for reserving the MSG TLP region at the end of the
IORESOURCE_MEM is to avoid generating holes in between, because when the
region is allocated using allocate_resource(), memory will be allocated
from the start of the window. Later, if memory gets allocated for an
endpoint of size bigger than 'region_align', there will be a hole between
MSG TLP region and endpoint memory.
This generic implementation is optional for the glue drivers and can be
overridden by a custom 'pme_turn_off' callback.
Link: https://lore.kernel.org/linux-pci/20240418-pme_msg-v8-5-a54265c39742@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Add "code" and "routing" into struct dw_pcie_ob_atu_cfg for triggering
INTx IRQs by iATU in the PCIe endpoint mode in near the future.
PCIE_ATU_INHIBIT_PAYLOAD is set to issue TLP type of Msg instead of
MsgD. This implementation supports the data-less messages only for now.
Link: https://lore.kernel.org/linux-pci/20240418-pme_msg-v8-3-a54265c39742@nxp.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
This is a preparation before adding the Msg-type outbound iATU
mapping. The respective update will require two more arguments added
to __dw_pcie_prog_outbound_atu(). That will make the already
complicated function prototype even more hard to comprehend accepting
_eight_ arguments.
To prevent that and keep the code more-or-less readable, move all the
outbound iATU-related arguments to a new config structure: struct
dw_pcie_ob_atu_cfg, and pass a pointer to dw_pcie_prog_outbound_atu(). The
structure should be locally defined and populated with the outbound iATU
settings implied by the caller context.
As a result of this change there is no longer need in having the two
distinctive methods for the Host and Endpoint outbound iATU setups since
the code can directly call the dw_pcie_prog_outbound_atu() method with the
config structure populated, so drop dw_pcie_prog_ep_outbound_atu().
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240418-pme_msg-v8-2-a54265c39742@nxp.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
