Sort the pinmux entries for both GMAC ctrl nodes in port order (A/B/C and
D/E/F respectively) and remove the extra blank line before the second
pinmux assignment.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260524092016.46346-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add support for the Geist board based on the Renesas R-Car R8A779MD (M3Le)
SoC, a register-compatible variant of the R8A77965 (M3-N) with reduced set
of peripherals.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Nguyen Tran <nguyen.tran.pz@bp.renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Link: https://patch.msgid.link/20260522172000.15096-1-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add DMA properties to the serial nodes on the RZ/G2L SoC.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260520132315.944117-1-claudiu.beznea@kernel.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add the max-frequency property set to 133333333 Hz (133.33 MHz) to both
SDHI0 and SDHI1 MMC controller nodes in the RZ/V2L (r9a07g054) device
tree, increasing performance by ca. 33%.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260520115144.60067-4-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add the max-frequency property set to 133333333 Hz (133.33 MHz) to both
SDHI0 and SDHI1 MMC controller nodes in the RZ/{G2L,G2LC} (r9a07g044)
device tree, increasing performance by ca. 33%.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260520115144.60067-3-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add the max-frequency property set to 133333333 Hz (133.33 MHz) to both
SDHI0 and SDHI1 MMC controller nodes in the RZ/{G2UL,Five} (r9a07g043)
device tree, increasing performance by ca. 33%.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260520115144.60067-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Describe the MFIS and MFIS SCP instances which are used for various
tasks including inter-processor communication. Remove the PRR node
because it is part of MFIS on R-Car X5H and should be handled using the
MFIS compatible. Also, describe the S-TCM transport area used for shared
memory mailboxing.
Signed-off-by: Vinh Nguyen <vinh.nguyen.xz@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260519074702.3308-5-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fully describe all available DRAM in the DT, and describe regions which
are not accessible because they are used by firmware in reserved-memory
nodes.
Replace the first memory bank memory@60600000 with memory@40000000 and a
518 MiB long reserved-memory no-map subnode. This memory region is used
by other cores in the system.
Reserve 32 kiB of memory at 0x8c100000 for parameters shared by IPL,
SCP, TFA BL31 and TEE.
Reserve 512 kiB of memory at 0x8c200000 for TFA BL31. The upcoming
upstream TFA 2.15 BL31 uses memory from 0x8c200000..0x8c242fff; rounding
up to 512 kiB is slight future-proofing.
Reserve 32 MiB of memory at 0x8c400000 for OPTEE-OS, which is the entire
OPTEE-OS TZ protected DRAM area.
Neither TFA BL31 nor OPTEE-OS modify the DT passed to Linux in any way
with any new reserved-memory {} nodes to reserve memory areas used by
the TFA BL31 or OPTEE-OS to prevent the next stage from using those
areas, which lets Linux use all of the available DRAM as it is described
in the DT that was passed in by U-Boot, including the areas that are
newly utilized by TFA BL31 or OPTEE-OS.
In case of high DRAM utilization, unless the memory used by TFA BL31 or
OPTEE-OS is properly reserved, Linux may use and corrupt the memory used
by TFA BL31 or OPTEE-OS, which would lead to the system becoming
unresponsive.
Fixes: ad142a4ef7 ("arm64: dts: renesas: r8a78000: Add initial Ironhide board support")
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260517163212.18016-1-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The HW user manual for the Renesas RZ/T2H and the RZ/N2H states that for
SDR104, SDR50, and HS200 to work properly the eMMC/SDHI interface pins
have to be configured as specified below:
- SDn_CLK pin - drive strength: Ultra High, slew rate: Fast,
- Other SDn_* pins: drive strength: High, slew rate: Fast,
Schmitt trigger: disabled (not applicable to SDn_RST pins).
HS DDR and DDR50 are currently not supported, and for every other bus
mode the eMMC/SDHI interface pins should be configured as specified
below:
- SDn_CLK pin - drive strength: High, slew rate: Fast,
- Other SDn_* pins: drive strength: Middle, slew rate: Fast,
Schmitt trigger: disabled (not applicable to SDn_RST pins).
Adjust the pin definitions accordingly.
Signed-off-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://patch.msgid.link/20260514210220.7616-1-fabrizio.castro.jz@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The Renesas R-Car X5H (R8A78000) SoC contains Arm CoreLink GIC-720AE
Generic Interrupt Controller with Multi View capability. Firmware has
access to configuration View 0, Linux kernel has access to View 1.
The Arm CoreLink GIC-720AE Generic Interrupt Controller Technical
Reference Manual, currently latest r2p1 [1], chapter "5. Programmers
model for GIC-720AE", subchapter "5.4 Redistributor registers
for control and physical LPIs summary", part "5.4.3 GICR_TYPER,
Redistributor Type Register", "Table 5-50: GICR_TYPER bit descriptions"
on page 200, clarifies register "GICR_TYPER" bit 4 "Last" behavior
in Multi View setup as follows:
Last
Last Redistributor:
0 ... This Redistributor is not the last Redistributor on the chip.
1 ... This Redistributor is the last Redistributor on the chip.
When GICD_CFGID.VIEW == 1, for views 1, 2, or 3 this bit
always returns 1.
On this SoC, GICD_CFGID.VIEW is 1 and the Linux kernel has access to
View 1, therefore Linux kernel GICv3 driver will interpret register
"GICR_TYPER" bit 4 "Last" = 1 in the first Redistributor in continuous
Redistributor page as that first Redistributor being the one and only
Redistributor and will stop processing the continuous Redistributor
page further. This will prevent the other Redistributors from being
recognized by the system and used for other PEs.
Because the hardware indicates that the continuous Redistributor page
is not continuous for View 1, 2, or 3, describe every Redistributor
separately in the DT. This makes all Redistributors for all cores
accessible in Linux.
[1] https://documentation-service.arm.com/static/69ef3c1cd35efd294e335c43
Arm® CoreLink™ GIC-720AE Generic Interrupt Controller
Revision: r2p1 / Issue 12 / 102666_0201_12_en
Fixes: 63500d12cf ("arm64: dts: renesas: Add R8A78000 SoC support")
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260514125328.20954-1-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Describe SMC based PSCI access in SoC DT. The system can interact with
TFA BL31 PSCI provider running on the Cortex-A cores via SMC calls.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260513225037.49803-1-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The RZ/V2N SoC provides an internal RTC, which is enabled in the DT.
The RZ/V2N EVK board also includes an external RTC in the RAA215300
PMIC.
Add an "rtc0" alias pointing to the on-SoC RTC node to ensure a stable
device numbering.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260506155804.3984418-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The RZ/V2H SoC provides an internal RTC, which is enabled in the DT.
The RZ/V2H EVK board also includes an external RTC in the RAA215300
PMIC.
Add an "rtc0" alias pointing to the on-SoC RTC node to ensure a stable
device numbering.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260506155804.3984418-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add audio_clk1 and audio_clk2 fixed-clock nodes to the RZ/G3L (r9a08g046)
SoC DTSI. These clocks are external to the SoC and their frequencies are
board-dependent, so they are defined with clock-frequency = <0> as
placeholders that must be overridden in board-level DTS files.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260505123708.134069-4-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add i2c{0..3} device nodes to RZ/G3L ("R9A08G046") SoC DTSI.
As the place holders for i2c0 is removed, add the pincontrol
device nodes to make it functional on the board DTS.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260505070206.7932-3-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The KSZ9031RNX reference manual [1] DS00002117K page 62 FIGURE 7-5:
POWER-UP/POWER-DOWN/RESET TIMING Note 2 states, that after the
de-assertion of reset, wait a minimum of 100 us before starting
programming on the MIIM (MDC/MDIO) interface. Set DT property
reset-deassert-us to three times that, 300 us, to provide ample
time between reset deassertion and MDIO access.
The KSZ9031RNX reference manual [1] DS00002117K page 62 TABLE 7-4:
POWER-UP/POWER-DOWN/RESET TIMING PARAMETERS row tSR Stable supply
voltages to de-assertion of reset is at minimum 10 ms. Set DT
property reset-assert-us to 10ms because the KSZ9031RNX RM does
not explicitly spell out how long the reset has to be asserted,
but this at least covers the worst case scenario.
[1] https://ww1.microchip.com/downloads/aemDocuments/documents/UNG/ProductDocuments/DataSheets/KSZ9031RNX-Data-Sheet-DS00002117.pdf
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260505034325.167797-12-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The KSZ9031RNX reference manual [1] DS00002117K page 62 FIGURE 7-5:
POWER-UP/POWER-DOWN/RESET TIMING Note 2 states, that after the
de-assertion of reset, wait a minimum of 100 us before starting
programming on the MIIM (MDC/MDIO) interface. Set DT property
reset-deassert-us to three times that, 300 us, to provide ample
time between reset deassertion and MDIO access.
The KSZ9031RNX reference manual [1] DS00002117K page 62 TABLE 7-4:
POWER-UP/POWER-DOWN/RESET TIMING PARAMETERS row tSR Stable supply
voltages to de-assertion of reset is at minimum 10 ms. Set DT
property reset-assert-us to 10ms because the KSZ9031RNX RM does
not explicitly spell out how long the reset has to be asserted,
but this at least covers the worst case scenario.
[1] https://ww1.microchip.com/downloads/aemDocuments/documents/UNG/ProductDocuments/DataSheets/KSZ9031RNX-Data-Sheet-DS00002117.pdf
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260505034325.167797-11-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The KSZ9031RNX reference manual [1] DS00002117K page 62 FIGURE 7-5:
POWER-UP/POWER-DOWN/RESET TIMING Note 2 states, that after the
de-assertion of reset, wait a minimum of 100 us before starting
programming on the MIIM (MDC/MDIO) interface. Set DT property
reset-deassert-us to three times that, 300 us, to provide ample
time between reset deassertion and MDIO access.
The KSZ9031RNX reference manual [1] DS00002117K page 62 TABLE 7-4:
POWER-UP/POWER-DOWN/RESET TIMING PARAMETERS row tSR Stable supply
voltages to de-assertion of reset is at minimum 10 ms. Set DT
property reset-assert-us to 10ms because the KSZ9031RNX RM does
not explicitly spell out how long the reset has to be asserted,
but this at least covers the worst case scenario.
[1] https://ww1.microchip.com/downloads/aemDocuments/documents/UNG/ProductDocuments/DataSheets/KSZ9031RNX-Data-Sheet-DS00002117.pdf
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260505034325.167797-10-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The KSZ9031RNX reference manual [1] DS00002117K page 62 FIGURE 7-5:
POWER-UP/POWER-DOWN/RESET TIMING Note 2 states, that after the
de-assertion of reset, wait a minimum of 100 us before starting
programming on the MIIM (MDC/MDIO) interface. Set DT property
reset-deassert-us to three times that, 300 us, to provide ample
time between reset deassertion and MDIO access.
The KSZ9031RNX reference manual [1] DS00002117K page 62 TABLE 7-4:
POWER-UP/POWER-DOWN/RESET TIMING PARAMETERS row tSR Stable supply
voltages to de-assertion of reset is at minimum 10 ms. Set DT
property reset-assert-us to 10ms because the KSZ9031RNX RM does
not explicitly spell out how long the reset has to be asserted,
but this at least covers the worst case scenario.
[1] https://ww1.microchip.com/downloads/aemDocuments/documents/UNG/ProductDocuments/DataSheets/KSZ9031RNX-Data-Sheet-DS00002117.pdf
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260505034325.167797-9-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The KSZ9031RNX reference manual [1] DS00002117K page 62 FIGURE 7-5:
POWER-UP/POWER-DOWN/RESET TIMING Note 2 states, that after the
de-assertion of reset, wait a minimum of 100 us before starting
programming on the MIIM (MDC/MDIO) interface. Set DT property
reset-deassert-us to three times that, 300 us, to provide ample
time between reset deassertion and MDIO access.
The KSZ9031RNX reference manual [1] DS00002117K page 62 TABLE 7-4:
POWER-UP/POWER-DOWN/RESET TIMING PARAMETERS row tSR Stable supply
voltages to de-assertion of reset is at minimum 10 ms. Set DT
property reset-assert-us to 10ms because the KSZ9031RNX RM does
not explicitly spell out how long the reset has to be asserted,
but this at least covers the worst case scenario.
[1] https://ww1.microchip.com/downloads/aemDocuments/documents/UNG/ProductDocuments/DataSheets/KSZ9031RNX-Data-Sheet-DS00002117.pdf
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260505034325.167797-8-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The KSZ9031RNX reference manual [1] DS00002117K page 62 FIGURE 7-5:
POWER-UP/POWER-DOWN/RESET TIMING Note 2 states, that after the
de-assertion of reset, wait a minimum of 100 us before starting
programming on the MIIM (MDC/MDIO) interface. Set DT property
reset-deassert-us to three times that, 300 us, to provide ample
time between reset deassertion and MDIO access.
The KSZ9031RNX reference manual [1] DS00002117K page 62 TABLE 7-4:
POWER-UP/POWER-DOWN/RESET TIMING PARAMETERS row tSR Stable supply
voltages to de-assertion of reset is at minimum 10 ms. Set DT
property reset-assert-us to 10ms because the KSZ9031RNX RM does
not explicitly spell out how long the reset has to be asserted,
but this at least covers the worst case scenario.
[1] https://ww1.microchip.com/downloads/aemDocuments/documents/UNG/ProductDocuments/DataSheets/KSZ9031RNX-Data-Sheet-DS00002117.pdf
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260505034325.167797-7-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The KSZ9031RNX reference manual [1] DS00002117K page 62 FIGURE 7-5:
POWER-UP/POWER-DOWN/RESET TIMING Note 2 states, that after the
de-assertion of reset, wait a minimum of 100 us before starting
programming on the MIIM (MDC/MDIO) interface. Set DT property
reset-deassert-us to three times that, 300 us, to provide ample
time between reset deassertion and MDIO access.
The KSZ9031RNX reference manual [1] DS00002117K page 62 TABLE 7-4:
POWER-UP/POWER-DOWN/RESET TIMING PARAMETERS row tSR Stable supply
voltages to de-assertion of reset is at minimum 10 ms. Set DT
property reset-assert-us to 10ms because the KSZ9031RNX RM does
not explicitly spell out how long the reset has to be asserted,
but this at least covers the worst case scenario.
[1] https://ww1.microchip.com/downloads/aemDocuments/documents/UNG/ProductDocuments/DataSheets/KSZ9031RNX-Data-Sheet-DS00002117.pdf
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260505034325.167797-6-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The KSZ9031RNX reference manual [1] DS00002117K page 62 FIGURE 7-5:
POWER-UP/POWER-DOWN/RESET TIMING Note 2 states, that after the
de-assertion of reset, wait a minimum of 100 us before starting
programming on the MIIM (MDC/MDIO) interface. Set DT property
reset-deassert-us to three times that, 300 us, to provide ample
time between reset deassertion and MDIO access.
The KSZ9031RNX reference manual [1] DS00002117K page 62 TABLE 7-4:
POWER-UP/POWER-DOWN/RESET TIMING PARAMETERS row tSR Stable supply
voltages to de-assertion of reset is at minimum 10 ms. Set DT
property reset-assert-us to 10ms because the KSZ9031RNX RM does
not explicitly spell out how long the reset has to be asserted,
but this at least covers the worst case scenario.
[1] https://ww1.microchip.com/downloads/aemDocuments/documents/UNG/ProductDocuments/DataSheets/KSZ9031RNX-Data-Sheet-DS00002117.pdf
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260505034325.167797-5-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The KSZ9031RNX reference manual [1] DS00002117K page 62 FIGURE 7-5:
POWER-UP/POWER-DOWN/RESET TIMING Note 2 states, that after the
de-assertion of reset, wait a minimum of 100 us before starting
programming on the MIIM (MDC/MDIO) interface. Set DT property
reset-deassert-us to three times that, 300 us, to provide ample
time between reset deassertion and MDIO access.
The KSZ9031RNX reference manual [1] DS00002117K page 62 TABLE 7-4:
POWER-UP/POWER-DOWN/RESET TIMING PARAMETERS row tSR Stable supply
voltages to de-assertion of reset is at minimum 10 ms. Set DT
property reset-assert-us to 10ms because the KSZ9031RNX RM does
not explicitly spell out how long the reset has to be asserted,
but this at least covers the worst case scenario.
[1] https://ww1.microchip.com/downloads/aemDocuments/documents/UNG/ProductDocuments/DataSheets/KSZ9031RNX-Data-Sheet-DS00002117.pdf
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260505034325.167797-4-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The KSZ9031RNX reference manual [1] DS00002117K page 62 FIGURE 7-5:
POWER-UP/POWER-DOWN/RESET TIMING Note 2 states, that after the
de-assertion of reset, wait a minimum of 100 us before starting
programming on the MIIM (MDC/MDIO) interface. Set DT property
reset-deassert-us to three times that, 300 us, to provide ample
time between reset deassertion and MDIO access.
The KSZ9031RNX reference manual [1] DS00002117K page 62 TABLE 7-4:
POWER-UP/POWER-DOWN/RESET TIMING PARAMETERS row tSR Stable supply
voltages to de-assertion of reset is at minimum 10 ms. Set DT
property reset-assert-us to 10ms because the KSZ9031RNX RM does
not explicitly spell out how long the reset has to be asserted,
but this at least covers the worst case scenario.
[1] https://ww1.microchip.com/downloads/aemDocuments/documents/UNG/ProductDocuments/DataSheets/KSZ9031RNX-Data-Sheet-DS00002117.pdf
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260505034325.167797-3-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The KSZ9031RNX reference manual [1] DS00002117K page 62 FIGURE 7-5:
POWER-UP/POWER-DOWN/RESET TIMING Note 2 states, that after the
de-assertion of reset, wait a minimum of 100 us before starting
programming on the MIIM (MDC/MDIO) interface. Set DT property
reset-deassert-us to three times that, 300 us, to provide ample
time between reset deassertion and MDIO access.
The KSZ9031RNX reference manual [1] DS00002117K page 62 TABLE 7-4:
POWER-UP/POWER-DOWN/RESET TIMING PARAMETERS row tSR Stable supply
voltages to de-assertion of reset is at minimum 10 ms. Set DT
property reset-assert-us to 10ms because the KSZ9031RNX RM does
not explicitly spell out how long the reset has to be asserted,
but this at least covers the worst case scenario.
[1] https://ww1.microchip.com/downloads/aemDocuments/documents/UNG/ProductDocuments/DataSheets/KSZ9031RNX-Data-Sheet-DS00002117.pdf
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260505034325.167797-2-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Use standard clock-controller node name for the CS2000-CP.
No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260504225704.115125-5-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Use standard clock-controller node name for the CS2000-CP.
No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260504225704.115125-4-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Use standard clock-controller node name for the CS2000-CP.
No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260504225704.115125-3-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Use standard clock-controller node name for the CS2000-CP.
No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260504225704.115125-2-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Use standard clock-controller node name for the CS2000-CP.
No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260504225704.115125-1-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add support for the Renesas R-Car M3Le (R8A779MD) SoC, a variant of the
R-Car M3-N (R8A77965) SoC. The Renesas M3Le SoC is a register-compatible
variant of the R8A77965 (M3-N) with reduced set of peripherals.
Signed-off-by: Nguyen Tran <nguyen.tran.pz@bp.renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260504144534.43745-7-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Document the compatible value for the Renesas R-Car M3Le (R8A779MD)
SoC and the Renesas Geist development board. The Renesas M3Le SoC is
a register-compatible variant of the R8A77965 (M3-N) with reduced set
of peripherals. The Geist board is derived from Renesas Salvator-X/XS
boards, with adjustment for the R8A779MD SoC.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Link: https://patch.msgid.link/20260504144534.43745-5-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Document backward compatibility support for the CS2500 chip, which is a
drop-in replacement for the CS2000 chip.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260504144534.43745-4-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Move all differences into panel-aa104xd12.dtsi, rename OF_GRAPH links to
generic lvds_panel_out and lvds_panel_in names, and parametrize the LVDS
output in use using RENESAS_LVDS_OUTPUT macro. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260504143751.42753-1-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Enable the PCIE1 slot available on the RZ/V2N EVK.
Note, the PCIE_REFCLK comes from 5L35023B versa clock generator, once the
support for this clock generator is added, the fixed clock node can be
removed and can be replaced with a reference to the clock generator.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260501105116.33452-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The SoC dtsi already defines the du node with its ports hierarchy,
including the du_out_rgb endpoint node under port@0. There is no need
to redefine the entire ports/port@0 structure in the board-level dtsi.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260420132211.1350656-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The Renesas RZ/N2H (R9A09G087) SoC has an MTU3 block.
Add support for it.
Signed-off-by: Cosmin Tanislav <cosmin-gabriel.tanislav.xa@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260410163530.383818-11-cosmin-gabriel.tanislav.xa@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The Renesas RZ/T2H (R9A09G077) SoC has an MTU3 block.
Add support for it.
Signed-off-by: Cosmin Tanislav <cosmin-gabriel.tanislav.xa@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260410163530.383818-10-cosmin-gabriel.tanislav.xa@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The TCIU8 interrupt used to be documented in earlier revisions of the
user manuals, but has since been removed. The corresponding entry is
now marked as reserved in the interrupt mapping tables of all supported
SoCs.
- Page 486, Table 8.2 Interrupt mapping (7/13) in the Renesas RZ/G2UL
Rev.1.40 User Manual
- Page 363, Table 8.2 Interrupt Mapping (6/13) in the Renesas RZ/Five
Rev.1.30 User Manual
- Page 528, Table 8.2 Interrupt mapping (7/13) in the Renesas RZ/G2L
and RZ/G2LC Rev.1.50 User Manual
- Page 540, Table 8.2 Interrupt mapping (7/13) in the Renesas RZ/V2L
Rev.1.50 User Manual
Remove the TCIU8 interrupt. This does not cause any breakage as the
driver does not make use of the interrupts.
Signed-off-by: Cosmin Tanislav <cosmin-gabriel.tanislav.xa@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260410163530.383818-9-cosmin-gabriel.tanislav.xa@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Describe coresight topology on R-Mobile APE6. Extend the current PTM node
with connection funnel, TPIU, ETB and replicator. The coresight on this
hardware is clocked from the ZT/ZTR trace clock.
Note that only core 0 part of the topology is described, because the
other cores are still not present in the DT.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260502185557.93061-5-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
