Lower the I2C2 bus clock frequency on the RZ/G3E SMARC SoM from 1MHz to
400kHz to improve compatibility with a wider range of I2C peripherals.
As the GreenPAK device is programmed to operate at 400kHz, the previous
1MHz setting was too aggressive, causing it to experience timing issues.
Fixes: f7a98e256e ("arm64: dts: renesas: rzg3e-smarc-som: Add I2C2 device pincontrol")
Signed-off-by: John Madieu <john.madieu.xa@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250518220812.1480696-1-john.madieu.xa@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
When the binding was originally written, it was assumed that all
ax45mp-caches had the same properties etc. This has turned out to be
incorrect, as the QiLai SoC has a different number of cache-sets.
Add a specific compatible for the RZ/Five for property enforcement and
in case there turns out to be additional differences between these
implementations of the cache controller.
Acked-by: Ben Zong-You Xie <ben717@andestech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/20250512-sphere-plenty-8ce4cd772745@spud
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
make dtbs:
arch/arm64/boot/dts/renesas/r8a779g0.dtsi:1269.24-1283.5: Warning (spi_bus_bridge): /soc/spi@e6ea0000: incorrect #address-cells for SPI bus
also defined at arch/arm64/boot/dts/renesas/r8a779g3-sparrow-hawk.dts:471.9-486.3
arch/arm64/boot/dts/renesas/r8a779g0.dtsi:1269.24-1283.5: Warning (spi_bus_bridge): /soc/spi@e6ea0000: incorrect #size-cells for SPI bus
also defined at arch/arm64/boot/dts/renesas/r8a779g3-sparrow-hawk.dts:471.9-486.3
arch/arm64/boot/dts/renesas/r8a779g3-sparrow-hawk.dtb: Warning (spi_bus_reg): Failed prerequisite 'spi_bus_bridge'
The Sparrow Hawk uses the MSIOF module in I2S mode instead of SPI mode,
triggering a conflict between the SPI bus bindings and dtc:
- Serial engines that can be SPI controllers must use "spi" as their
node names,
- Dtc assumes nodes named "spi" are always SPI controllers.
Fix this by disabling this specific warning for this board.
Fixes: ca764d5321 ("arm64: dts: renesas: sparrow-hawk: Add MSIOF Sound support")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Closes: https://lore.kernel.org/20250506192033.77338015@canb.auug.org.au
Suggested-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/fbad3581f297d5b95a3b2813bbae7dba25a523fd.1747039399.git.geert+renesas@glider.be
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The CPLD has no dedicated driver, so apply the pinmux settings with the
pinmux driver instead.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250508074311.20343-5-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
- Add the missing "ethernet3" alias for the Ethernet TSN port, so
U-Boot will fill its local-mac-address property based on the
"eth3addr" environment variable (if set), avoiding a random MAC
address being assigned by the OS,
- Rename the numerical Ethernet PHY label to "tsn0_phy", to avoid
future conflicts, and for consistency with the "avbN_phy" labels.
Fixes: 3d8e475bd7 ("arm64: dts: renesas: white-hawk-single: Wire-up Ethernet TSN")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/367f10a18aa196ff1c96734dd9bd5634b312c421.1746624368.git.geert+renesas@glider.be
A simple CTS/RTS capable UART on a good old D-sub connector.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250424102805.22803-2-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The GPT4 IOs are available on the carrier board's PMOD0 connector (J1).
Enable the GPT on the carrier board by adding the GPT pinmux and node on
the carrier board dtsi file.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250424054050.28310-4-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This port bypasses the switch and is directly connected to the GMAC.
Co-developed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250414100206.7185-2-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Enable TCAN1046V-Q1 CAN Transceiver populated on RZ/G3E SMARC EVK by
modelling it as two instances of tcan1042.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250320164121.193857-4-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The first ISP instance on V4M has both a channel select and core
function block, describe the core region in addition to the existing cs
region. While at it update the second ISP to match the new bindings and
add the reg-names and interrupt-names property.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250423163113.2961049-5-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
All ISP instances on V4H have both a channel select and core function
block, describe the core region in addition to the existing cs region.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250423163113.2961049-4-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
All ISP instances on V3U have both a channel select and core function
block, describe the core region in addition to the existing cs region.
The interrupt number already described intended to reflect the cs
function but did incorrectly describe the core block. This was not
noticed until now as the driver do not make use of the interrupt for the
cs block.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250423163113.2961049-3-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Enable RAA215300 PMIC and built-in RTC support on the RZ/G3E SoM module.
Also add related clock and interrupt signals.
Signed-off-by: John Madieu <john.madieu.xa@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250329121258.172099-3-john.madieu.xa@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add a device node for I2C2 pincontrol. Also enable the I2C2 device node
with 1MHz clock frequency as it is connected to the RAA215300 PMIC on
the RZ/G3E SoM.
Signed-off-by: John Madieu <john.madieu.xa@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250329121258.172099-2-john.madieu.xa@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add the initial device tree for the Renesas RZ/V2N EVK board, based on
the R9A09G056N48 SoC. Enable basic board functionality, including:
- Memory mapping (reserve the first 128MB for the secure area)
- Clock inputs (QEXTAL, RTXIN, AUDIO_EXTAL)
- PINCTRL configurations for peripherals
- Serial console (SCIF)
- SDHI1 with power control and UHS modes
Update the Makefile to include the new DTB.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250407191628.323613-13-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
DT bindings and binding definitions for the Renesas RZ/V2N (R9A09G056)
SoC, shared by driver and DT source files.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCZ/zMdQAKCRCKwlD9ZEnx
cPigAP97UeFb9VLWbPeUMSm6A2aPz4loif/U0G+SsYIe10CYgAEA17AYkjokTNGz
dOLVl3cj7EW6jIhuXmmK1/49Xc97IgU=
=fEuX
-----END PGP SIGNATURE-----
Merge tag 'renesas-r9a09g056-dt-binding-defs-tag1' into renesas-dts-for-v6.16
Renesas RZ/V2N DT Bindings and Definitions
DT bindings and binding definitions for the Renesas RZ/V2N (R9A09G056)
SoC, shared by driver and DT source files.
Add documentation for the pin controller found on the Renesas RZ/V2N
(R9A09G056) SoC. The RZ/V2N PFC differs slightly from the RZ/G2L family
and is almost identical to the RZ/V2H(P) SoC, except that the RZ/V2H(P) SoC
has an additional dedicated pin.
To account for this, a SoC-specific compatible string,
'renesas,r9a09g056-pinctrl', is introduced for the RZ/V2N SoC.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250407191628.323613-10-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Document the device tree bindings for the Renesas RZ/V2N (R9A09G056)
SoC Clock Pulse Generator (CPG).
Update `renesas,rzv2h-cpg.yaml` to include the compatible string for
RZ/V2N SoC and adjust the title and description accordingly.
Additionally, introduce `renesas,r9a09g056-cpg.h` to define core clock
constants for the RZ/V2N SoC. Note the existing RZ/V2H(P) family-specific
clock driver will be reused for this SoC.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250407191628.323613-7-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add the RZ/V2N (R9A09G056) variant to the existing RZ/V2H(P) System
Controller (SYS) binding, as both IPs are very similar.
However, they have different SoC IDs, and the RZ/V2N does not have
PCIE1 configuration registers, unlike the RZ/V2H(P) SYS IP. To handle
these differences, introduce a new compatible string
`renesas,r9a09g056-sys`.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250407191628.323613-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Document the Renesas RZ/V2N (R9A09G056) SoC variants, distinguishing
between configurations with and without specific hardware features such
as GPU, ISP, and cryptographic extensions. Also, document the
"renesas,rzv2n-evk" compatible string for the RZ/V2N EVK board.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250407191628.323613-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The keys are connected to the I2C GPIO extender which has the interrupt
pin not connected. So, we need to poll.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250328153134.2881-12-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The actual sensor might differ, but all known are LM75B compatible.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250328153134.2881-10-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Schematics mention a 24cs64 on the bus, but I definitely have only a
24c64. So, it is only mentioned as a comment.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250328153134.2881-9-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
To match the documentation and schematics, they are numbered from 1 and
not from 0.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250328153134.2881-8-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The EB board (Expansion board) supports both RZ/N1D and RZ-N1S. Since this
configuration targets only the RZ/N1D, it is named r9a06g032-rzn1d400-eb.
It adds support for the 2 additional switch ports (port C and D) that are
available on that board.
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
[Thomas: move the DTS to the Renesas directory, declare the PHY LEDs]
Signed-off-by: Thomas Bonnefille <thomas.bonnefille@bootlin.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/20250324-rzn1d400-eb-v4-1-d7ebbbad1918@bootlin.com
[wsa: Correct LAN LED nodes]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250411095425.1842-2-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Remove undocumented compatible micron,mt25qu512a.
This fixes the dtbs warning: failed to match any schema with compatible:
['micron,mt25qu512a', 'jedec,spi-nor']
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250309184326.75452-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Enable SDHI1 on the RZ/G3E SMARC EVK platform using gpio regulator for
voltage switching.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250206134047.67866-9-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add support for enabling SD on SDHI0 on RZ/G3E SMARC SoM. It is enabled
by setting the macro SW_SD0_DEV_SEL to 1 in board DTS and setting the
switch SYS.1 to ON position on the SoM.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250206134047.67866-8-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add support for enabling SDHI internal regulator, by overriding the
status on the board DTS, when needed.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/20250206134047.67866-6-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The "real" linux/types.h UAPI header gracefully degrades to a NOOP when
included from assembly code.
Mirror this behaviour in the tools/ variant.
Test for __ASSEMBLER__ over __ASSEMBLY__ as the former is provided by the
toolchain automatically.
Reported-by: Mark Brown <broonie@kernel.org>
Closes: https://lore.kernel.org/lkml/af553c62-ca2f-4956-932c-dd6e3a126f58@sirena.org.uk/
Fixes: c9fbaa8795 ("selftests: vDSO: parse_vdso: Use UAPI headers instead of libc headers")
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Link: https://patch.msgid.link/20250321-uapi-consistency-v1-1-439070118dc0@linutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
