With deferrable card binding the sound card driver tries to
get the mclk configuration before it is setup in sai3 node.
Fix this by setting the sai clock config for the audio codec as well.
Fixes: d8f9d81265 ("arm64: dts: imx8mp: Add analog audio output on i.MX8MP TQMa8MPxL/MBa8MPxL")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
NXP i.MX95 19x19 FRDM PRO is cost-effective with extensive
expansion capabilities based on the i.MX95 19x19 SoC.
It is designed for AI and robotic situation.
Difference with i.MX95 15x15 FRDM:
- Use i.MX95 19x19 package
- Support 2 KEY-M M.2 PCIE
- 10G ETH interface
- Secure Element interface
Add device tree for this board. Including:
- LPUART1 and LPUART5
- NETC
- USB
- 2 M-Key M.2 PCIe
- uSDHC1, uSDHC2 and uSDHC3
- FlexCAN1 and FlexCAN3 (CAN1 is reserved by M7)
- LPI2C3, LPI2C4 and their child nodes
- Watchdog3
- SAI, MQS, MICFIL
Signed-off-by: Joseph Guo <qijian.guo@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add the i.MX95 19x19 FRDM PRO board in the binding document.
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Joseph Guo <qijian.guo@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add PWM0 and PWM1 for S32G2 and S32G3 SoCs
Reviewed-by: Enric Balletbo i Serra <eballetb@redhat.com>
Signed-off-by: Khristine Andreea Barbulescu <khristineandreea.barbulescu@oss.nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add missing hex annotation to fix the SWT8 watchdog address in 'reg'
property, as reported by dtc W=1:
s32g3.dtsi:863.27-869.5: Warning (simple_bus_reg): /soc@0/watchdog@40500000: simple-bus unit address format error, expected "269fb20"
Lack of hex '0x' meant address would be interpreted as decimal thus
completely different value used as this device MMIO. If device was
enabled this could lead to corruption of other device address space and
broken boot.
Cc: stable@vger.kernel.org
Fixes: 6db84f0427 ("arm64: dts: s32g3: Add the Software Timer Watchdog (SWT) nodes")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@oss.qualcomm.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add the MCP251xFD CAN controller connected to LPSPI7 chip select 1 on
the Sonata carrier board.
Add the second SPI chip select GPIO and describe the CAN interrupt and
pinctrl configuration.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add the reset GPIO for the TPM device on the Sonata carrier board and
label the node accordingly.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add support for the SolidRun i.MX8DXL System-on-Module (revision 2.1)
and its corresponding evaluation carrier board, the HummingBoard
Telematics (revision 2.0).
The SoM features:
- eMMC
- GNSS with 1PPS
- V2X DSRC Radio
- Secure Element for V2X Applications
- Inertial Sensor
- Pressure Sensor
- Compass
The HummingBoard Telematics carrier board features:
- Cellular Modem
- WiFi & Bluetooth
- RTC with backup battery
- CAN
- 100Base-TX Ethernet
- 100Base-T1 Ethernet
- Multi-interface I/O connector
- Multi-interface add-on board connector
The multi-interface I/O connector supplies power and provides basic I/O
(Console UART, 100Base-TX, 100Base-T1, CAN, and power-supply logic level
GPIOs). The SolidRun Evaluation Kit includes a suitable cable and
adapter board that breaks these out into RJ45, USB Type-A, microUSB
Console, and Terminal Block connectors.
The multi-interface add-on board connector provides additional
interfaces (5x 100Base-T1, 2x SGMII, USB 2.0 shared with the cellular
modem, CAN, MDIO, SPI, UART, PCIe, I2C, and GPIO). These add-on
interfaces are disabled by default in the base device tree and are
intended to be enabled and extended via device tree overlays.
Note that a few components physically present on the SoM were omitted
from this description due to a lack of upstream bindings and drivers:
- Pressure Sensor
- V2X DSRC Radio
- Secure Element
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Josua Mayer <josua@solid-run.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add binding for the SolidRun i.MX8DXL based System on Module, and the
reference HummingBoard Telematics.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Josua Mayer <josua@solid-run.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add support for the SolidRun LX2160A Twins board in its single cpu
configuration.
The twins board is designed to host a pair of LX2160A CEX-7 modules,
sharing a single PCI-E connector in multi-host mode.
It may be assembled in two configurations (different assembly options
facilitating signal re-routing), with a single or with dual CEX-7
module. Their marketing names are:
- SolidWAN Single LX2160
- SolidWAN Dual LX2160
Add the single configuration, featuring:
- 8x SFP (1Gbps)
- 8x SFP+ (1/10Gbps)
- PCI-E OCP card connector
- USB-3.0 front-panel header with single port
- microSD
- dual hot-swappable power supplies
Signed-off-by: Josua Mayer <josua@solid-run.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
LX2160A CEX-7 module provides a total of 4 USB ports to the carrier
board, one from first usb controller, and 3 from a hub behind the second
controller.
Both controllers currently have their status set okay in the module's
dtsi file. However devices should be disabled by default when
incomplete.
The first USB controller is only completed by a carrier board featuring
a device or USB connector.
The second controller hosts a USB hub and should therefore be active.
Add description for the USB hub, and enable the first controller only in
the carrier board description.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Originally includes were defined hierarchically:
- CEX-7 Module includes SoC
- Clearfog-CX & Honeycomb common parts include CEX-7 Module
- Boards include common parts
This makes it difficult to modify the includes on a per-board level,
e.g. when adding a new board based on CEX-7 module but revision 2 SoC
(which now has its own soc dtsi).
Move includes of both SoC and CEX-7 module out of common parts and into
each board dts.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
The dts version tag should only appear in the top level dts file.
Since the cex-7 module and clearfog-itx are shared code intended for
inclusion, drop their dts version tags.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
The SolidRun LX2160A Twins board supports two configurations, one with
with a single CEX-7 module, and one with two (dual).
The single configuration is a specific assembly that maximises
connectivity for single cpu by routing some second cpu resources to the
first via zero-Ohm resistors.
The dual configuration was not yet tested and is intentionally omitted.
Initial review strongly suggests that the dual configuration will have
different bindings, because from either cpu point of view the board
appears different (e.g. different number of sfp, fewer i2c gpio).
Add binding for the single variant only.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
The LX2162A Clearfog board has a green LED on each of four SFP ports.
Describe in device-tree that their colour is green and function "lan".
Signed-off-by: Josua Mayer <josua@solid-run.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
The SoC dtsi has always enabled serdes block 1, enabled dpmac and
disabled pcie nodes.
Drop the superfluous status properties on these nodes.
Further drop crypto alias as SoM dtsi already set it.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
LX2160A and LX2162A are different packages of the same silicon. While
LX2160A had two revisions, LX2162A was released later based on LX2160A
revision 2.
Commit a8fe6c8dfc ("arm64: dts: fsl-lx2160a: add rev2 support") has added
a new soc dtsi for revision 2.
Update LX2162A Clearfog description to use revision 2 dtsi.
Fixes: 5093b190f9 ("arm64: dts: freescale: Add support for LX2162 SoM & Clearfog Board") # no-stable
Signed-off-by: Josua Mayer <josua@solid-run.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Fix the PCIe outbound memory ranges for both pcie0 and pcie1
controllers on i.MX95.
The memory window size was incorrectly set to 256MB during initial
bring-up, but the hardware supports up to 4GB of outbound address space
per controller.
Additionally, the ECAM region cannot be mapped as I/O space. Use a
memory-mapped region for I/O space instead, and relocate the 1MB I/O
region to immediately follow the memory region at offset 0xf0000000
within each window.
Update the outbound address space layout per controller as follows:
- 3.5GB 64-bit prefetchable memory
- 256MB 32-bit non-prefetchable memory
- 1MB I/O
Fixes: 3b1d5deb29 ("arm64: dts: imx95: add pcie[0,1] and pcie-ep[0,1] support")
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
The PHYs of the EQOS interface is supported to be reset by I2C GPIO
expander. So add the support to reset PHYs.
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Both the PHYs of the EQOS interface and the FEC interface are supported
to be reset by I2C GPIO expander. So add the support to reset PHYs.
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
The wdog3 node enables fsl,ext-reset-output to assert an external
reset signal upon watchdog timeout, but lacks pinctrl configuration
for the physical pad.
Without proper pinctrl settings, which could cause the watchdog timeout
to fail to reset the board hardware.
Add pinctrl configuration to ensure the pin is properly muxed and
configured for external watchdog reset functionality.
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
The wdog3 node enables fsl,ext-reset-output to assert an external
reset signal upon watchdog timeout, but lacks pinctrl configuration
for the physical pad.
Without proper pinctrl settings, which could cause the watchdog timeout
to fail to reset the board hardware.
Add pinctrl configuration to ensure the pin is properly muxed and
configured for external watchdog reset functionality.
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
The clock-frequency property is not implemented. Remove it to clean up the
device tree.
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add the bootph-all property to ULP watchdog nodes across multiple i.MX
SoC device trees, ensuring the watchdog is available during all boot
phases.
The affected watchdog nodes are:
- imx8ulp: wdog3
- imx91/93: wdog3, wdog4, wdog5
- imx94: wdog3
- imx95: wdog3
- imx952: wdog3
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
The DDR Performance Monitor node was added with incorrect interrupt
number 91, which actually belongs to the wdog4 watchdog. Fix it to the
correct interrupt number 374.
Fixes: e918e5f847 ("arm64: dts: imx94: add DDR Perf Monitor node")
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Reviewed-by: Xu Yang <xu.yang_2@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add ADC0 and ADC1 for S32G2 and S32G3 SoCs.
Signed-off-by: Khristine Andreea Barbulescu <khristineandreea.barbulescu@oss.nxp.com>
Reviewed-by: Enric Balletbo i Serra <eballetb@redhat.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
The vpcie-supply property should reference the regulator that controls
the actual M.2 power supply, not the W_DISABLE1# signal.
On imx943-evk:
- reg_m2_wlan controls M.2 W_DISABLE1# signal
- reg_m2_pwr controls the actual M.2 power supply
Fix the vpcie-supply to use reg_m2_pwr for proper power control in
PCIe endpoint mode.
Fixes: 1962c596d51c ("arm64: dts: imx943-evk: Add pcie[0,1] and pcie-ep[0,1] support")
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add PIT0 and PIT1 for S32G2 and S32G3 SoCs
Signed-off-by: Khristine Andreea Barbulescu <khristineandreea.barbulescu@oss.nxp.com>
Reviewed-by: Enric Balletbo i Serra <eballetb@redhat.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
There is an onboard level shifter for the SPI signals that causes
additional propagation delay and renders the SPI transmission
unreliable at 20 MHz. Reduce the clock frequency to a safe value.
Fixes: 946ab10e3f ("arm64: dts: Add support for Kontron OSM-S i.MX8MP SoM and BL carrier board")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Since describing the PCIe PERST# property under Host Bridge node is now
deprecated, it is recommended to add it to the Root Port node, so
creating the Root Port node and add the reset-gpios property in Root
Port.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Since describing the PCIe PERST# property under Host Bridge node is now
deprecated, it is recommended to add it to the Root Port node, so
creating the Root Port node and add the reset-gpios property in Root
Port.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Since describing the PCIe PERST# property under Host Bridge node is now
deprecated, it is recommended to add it to the Root Port node, so
creating the Root Port node and add the reset-gpios property in Root
Port.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Since describing the PCIe PERST# property under Host Bridge node is now
deprecated, it is recommended to add it to the Root Port node, so
creating the Root Port node and add the reset-gpios property in Root
Port.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Since describing the PCIe PERST# property under Host Bridge node is now
deprecated, it is recommended to add it to the Root Port node, so
creating the Root Port node and add the reset-gpios property in Root
Port.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add DT overlays to support DH i.MX8M Plus DHCOM SoM variants and carrier
board expansion modules. The following DT overlays are implemented:
- SoM:
- DH 660-x00 SoM with 1xRMII PHY
- DH 660-x00 SoM with 2xRMII PHY
- PDK2:
- DH 505-200 Display board in edge connector X12 via direct LVDS
- DH 531-100 SPI/I2C board in header X21
- DH 531-200 SPI/I2C board in header X22
- DH 560-200 Display board in edge connector X12
- PDK3:
- DH 505-200 Display board in edge connector X36 via direct LVDS
- DH 531-100 SPI/I2C board in header X40
- DH 531-200 SPI/I2C board in header X41
- DH 560-300 Display board in edge connector X36
- EA muRata 2AE M.2 A/E-Key card in connector X20
- NXP SPF-29853-C1 MINISASTOCSI with OV5640 sensor in connector X31
- NXP SPF-29853-C1 MINISASTOCSI with OV5640 sensor in connector X29
- PicoITX:
- DH 626-100 Display board in edge connector X2
Signed-off-by: Marek Vasut <marex@nabladev.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
The vpcie-supply property should reference the regulator that controls
the actual M.2 power supply, not the W_DISABLE1# signal.
On imx95-19x19-evk:
- reg_pcie0 controls M.2 W_DISABLE1# signal
- reg_m2_pwr controls the actual M.2 power supply
Fix the vpcie-supply to use reg_m2_pwr for proper power control in
PCIe endpoint mode.
Fixes: 58bea81052 ("arm64: dts: imx95: add pcie1 ep overlay file and create pcie-ep dtb files")
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Reviewed-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
For PCIe endpoint mode, only M.2 power supply needs to be ensured.
On imx8qxp-mek, the M.2 power is always on and cannot be controlled,
while reg_pcieb only controls the M.2 W_DISABLE1# signal. Remove the
unnecessary vpcie-supply property from pcie0_ep node.
Fixes: 1c9b0c6044 ("arm64: dts: imx8: use common imx-pcie0-ep.dtso to enable PCI ep function")
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Reviewed-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
For PCIe endpoint mode, only M.2 power supply needs to be ensured.
On imx8dxl-evk, the M.2 power is always on and cannot be controlled,
while reg_pcieb only controls the M.2 W_DISABLE1# signal. Remove the
unnecessary vpcie-supply property from pcie0_ep node.
Also remove reset-gpio as PCIe endpoint mode doesn't require reset
control.
Fixes: c1c4820b60 ("arm64: dts: imx8dxl-evk: Add pcie0-ep node and use unified pcie0 label")
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Reviewed-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Replace deprecated "gpio" property with "gpios" in
regulator-vmmc-usdhc2 fixed regulator node.
Signed-off-by: Antoine Gouby <antoine.gouby@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Apply improved drive-strength values and pull-up/down configurations as
devised from hardware measurements to improve signal quality on PHYTEC
phyCORE-i.MX 91/93 SoM based boards. Also improve eMMC HS400 mode by
setting property "fsl,strobe-dll-delay-target" which shifts the strobe
DLL sampling window to the optimal position.
Signed-off-by: Christoph Stoidner <c.stoidner@phytec.de>
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
According to measurements, the PHY reset signal shows an overshoot on
the rising edge that exceeds the specified limits (max 2.1V) when using
X4 strength on ENET2_RXC. Reduce drive-strength to X1 to decrease the
overshoot and bring signal within specification limits.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Set PMIC BUCK5 mode to forced PWM (Pulse Width Modulation) mode instead
of the default automatic PFM and PWM transition mode. FPWM mode produces
less ripple on the output voltage rail under light load conditions. And
since BUCK5 supplies SoC internal ADC reference voltage we need to keep
voltage ripple to a minimum. This solves issues with the occasional ADC
calibration procedure failures on phyCORE-i.MX91/93 SoM based boards.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Support tianma,tm050rdh03 DPI panel on i.MX93 9x9 QSB.
Move the common parts from imx93-9x9-qsb-ontat-kd50g21-40nt-a1.dtso into
imx93-9x9-qsb-ontat-kd50g21-40nt-a1.dtsi for reuse by the tm050rdh03
overlay file.
The panel connects with the QSB board through an adapter board[1]
designed by NXP.
Link: https://www.nxp.com/design/design-center/development-boards-and-designs/parallel-lcd-display:TM050RDH03-41 [1]
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Some i.MX boards (i.MX8MP EVK and i.MX95-15x15 EVK) have M.2 connectors
that are physically wired to both USDHC and PCIe controllers. The
default device tree enables USDHC for SDIO WiFi modules and disables
PCIe to avoid regulator conflicts.
Add a common imx-m2-pcie.dtso that can be applied to enable PCIe and
disable USDHC when a PCIe module is installed in the M.2 connector.
This creates the following DTB files:
- imx8mp-evk-pcie.dtb: i.MX8MP EVK with PCIe enabled
- imx95-15x15-evk-pcie.dtb: i.MX95-15x15 EVK with PCIe enabled
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Disable the PCIe bus in the default device tree to avoid shared
regulator conflicts between SDIO and PCIe buses. The non-deterministic
probe order between these two buses can break the PCIe initialization
sequence, causing PCIe devices to fail detection intermittently.
On i.MX95-15x15 EVK board, the M.2 connector is physically wired to both
USDHC3 and PCIe0, however the out-of-box module is SDIO IW612 WiFi, so
enable SDIO WiFi in the default imx95-15x15-evk.dts.
Add 'm2_usdhc' label to USDHC3 to support device tree overlay for PCIe
modules. Users who need PCIe can use imx95-15x15-evk-pcie.dtb (added in
a follow-up patch) which applies an overlay to enable PCIe and disable
USDHC3.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Disable the PCIe bus in the default device tree to avoid shared
regulator conflicts between SDIO and PCIe buses. The non-deterministic
probe order between these two buses can break the PCIe initialization
sequence, causing PCIe devices to fail detection intermittently.
On i.MX8MP EVK board, the M.2 connector is physically wired to both
USDHC1 and PCIe0, however the out-of-box module is SDIO IW612 WiFi, so
enable the SDIO WiFi in the default imx8mp-evk.dts.
Add 'm2_usdhc' label to USDHC1 to support device tree overlay for PCIe
modules. Users who need PCIe can use imx8mp-evk-pcie.dtb (added in a
follow-up patch) which applies an overlay to enable PCIe and disable
USDHC1.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
