The device tree overlay for TEVI-OV5640 requires following voltage
supplies:
AVDD-supply: Analog voltage supply, 2.8 volts
DOVDD-supply: Digital I/O voltage supply, 1.8 volts
DVDD-supply: Digital core voltage supply, 3.3 volts
Add them in the overlay.
Signed-off-by: Rishikesh Donadkar <r-donadkar@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Link: https://lore.kernel.org/r/20250506045225.1246873-3-r-donadkar@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The device tree overlay for OV5640 requires following voltage
supplies:
AVDD-supply: Analog voltage supply, 2.8 volts
DOVDD-supply: Digital I/O voltage supply, 1.8 volts
DVDD-supply: Digital core voltage supply, 1.5 volts
Add them in the overlay.
Signed-off-by: Rishikesh Donadkar <r-donadkar@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Link: https://lore.kernel.org/r/20250506045225.1246873-2-r-donadkar@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The device tree overlay for OV5640 requires following voltage
supplies as mentioned in the table 8-3 of the data-sheet [1].
AVDD-supply: Analog voltage supply, 2.8 volts
DOVDD-supply: Digital I/O voltage supply, 1.8 volts
DVDD-supply: Digital core voltage supply, 1.5 volts
Add them in the overlay.
Link: https://cdn.sparkfun.com/datasheets/Sensors/LightImaging/OV5640_datasheet.pdf
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Signed-off-by: Rishikesh Donadkar <r-donadkar@ti.com>
Link: https://lore.kernel.org/r/20250502162539.322091-4-r-donadkar@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The device tree overlay for the IMX219 sensor requires three voltage
supplies to be defined: VANA (analog), VDIG (digital core), and VDDL
(digital I/O) [1].
Add the corresponding voltage supply definitions in the overlay so
that the same topography as dt-bindings is present in the DT overlay.
Link: https://datasheets.raspberrypi.com/camera/camera-module-2-schematics.pdf [1]
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Signed-off-by: Rishikesh Donadkar <r-donadkar@ti.com>
Link: https://lore.kernel.org/r/20250502162539.322091-3-r-donadkar@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Add regulator node for AM62P-SK
VCC_3V3_MAIN is the output of LM5141-Q1, and it serves as an input to
TPS22965DSGT which produces VCC_3V3_SYS [1]
VCC_3V3_SYS servers as vin-supply for peripherals like CSI [1].
Link: https://www.ti.com/lit/zip/sprr487 [1]
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Signed-off-by: Rishikesh Donadkar <r-donadkar@ti.com>
Link: https://lore.kernel.org/r/20250502162539.322091-2-r-donadkar@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Set eMMC clock parents to the defaults which is MAIN_PLL0_HSDIV5_CLKOUT
for eMMC. This change is necessary since DM is not implementing the
correct procedure to switch PLL clock source for eMMC and MMC CLK mux is
not glich-free. As a preventative action, lets switch back to the defaults.
Fixes: b5080c7c1f ("arm64: dts: ti: k3-am62p: Add nodes for more IPs")
Cc: stable@vger.kernel.org
Signed-off-by: Judith Mendez <jm@ti.com>
Acked-by: Udit Kumar <u-kumar1@ti.com>
Acked-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20250429163337.15634-4-jm@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Set eMMC clock parents to the defaults which is MAIN_PLL0_HSDIV5_CLKOUT
for eMMC. This change is necessary since DM is not implementing the
correct procedure to switch PLL clock source for eMMC and MMC CLK mux is
not glich-free. As a preventative action, lets switch back to the defaults.
Fixes: d3ae4e8d8b ("arm64: dts: ti: k3-am62a-main: Add sdhci0 instance")
Cc: stable@vger.kernel.org
Signed-off-by: Judith Mendez <jm@ti.com>
Acked-by: Udit Kumar <u-kumar1@ti.com>
Acked-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20250429163337.15634-3-jm@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Set eMMC clock parents to the defaults which is MAIN_PLL0_HSDIV5_CLKOUT
for eMMC. This change is necessary since DM is not implementing the
correct procedure to switch PLL clock source for eMMC and MMC CLK mux is
not glich-free. As a preventative action, lets switch back to the defaults.
Fixes: c37c58fdeb ("arm64: dts: ti: k3-am62: Add more peripheral nodes")
Cc: stable@vger.kernel.org
Signed-off-by: Judith Mendez <jm@ti.com>
Acked-by: Udit Kumar <u-kumar1@ti.com>
Acked-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20250429163337.15634-2-jm@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The PCIe reference clock required by the PCIe Endpoints connected to the
PCIe connector corresponding to the PCIe1 instance of PCIe on J784S4-EVM
and J742S2-EVM is driven by the ACSPCIE0 module. Add the device-tree
support for enabling the same.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20250422123218.3788223-3-s-vadapalli@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The ACSPCIE0 module on TI's J784S4 SoC is capable of driving the
reference clock required by the PCIe Endpoint device. It is an
alternative to on-board and external reference clock generators.
Add the device-tree node for the same.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20250422123218.3788223-2-s-vadapalli@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The PCIe0 and PCIe1 instances of PCIe in J742S2 and J784S4 SoCs support:
1. 128 MB address region in the 32-bit address space
2. 4 GB address region in the 64-bit address space
The default configuration is that of a 128 MB address region in the
32-bit address space. While this might be sufficient for most use-cases,
it is insufficient for supporting use-cases which require larger address
spaces. Therefore, switch to using the 64-bit address space with a 4 GB
address region.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20250422120042.3746004-8-s-vadapalli@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The PCIe0 instance of PCIe in J722S SoC supports:
1. 128 MB address region in the 32-bit address space
2. 4 GB address region in the 64-bit address space
The default configuration is that of a 128 MB address region in the
32-bit address space. While this might be sufficient for most use-cases,
it is insufficient for supporting use-cases which require larger address
spaces. Therefore, switch to using the 64-bit address space with a 4 GB
address region.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20250422120042.3746004-7-s-vadapalli@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The PCIe1 instance of PCIe in J721S2 SoC supports:
1. 128 MB address region in the 32-bit address space
2. 4 GB address region in the 64-bit address space
The default configuration is that of a 128 MB address region in the
32-bit address space. While this might be sufficient for most use-cases,
it is insufficient for supporting use-cases which require larger address
spaces. Therefore, switch to using the 64-bit address space with a 4 GB
address region.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20250422120042.3746004-6-s-vadapalli@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The PCIe0 and PCIe1 instances of PCIe in J721E SoC support:
1. 128 MB address region in the 32-bit address space
2. 4 GB address region in the 64-bit address space
The default configuration is that of a 128 MB address region in the
32-bit address space. While this might be sufficient for most use-cases,
it is insufficient for supporting use-cases which require larger address
spaces. Therefore, switch to using the 64-bit address space with a 4 GB
address region.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20250422120042.3746004-5-s-vadapalli@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The PCIe0 DAT1 and PCIe1 DAT1 are 4 GB address regions in the 64-bit
address space of the respective PCIe Controllers. Hence, update the
ranges to include them.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20250422120042.3746004-4-s-vadapalli@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The PCIe0 instance of PCIe in J7200 SoC supports:
1. 128 MB address region in the 32-bit address space
2. 4 GB address region in the 64-bit address space
The default configuration is that of a 128 MB address region in the
32-bit address space. While this might be sufficient for most use-cases,
it is insufficient for supporting use-cases which require larger address
spaces. Therefore, switch to using the 64-bit address space with a 4 GB
address region.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20250422120042.3746004-3-s-vadapalli@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The PCIe0 instance of PCIe in AM64 SoC supports:
1. 128 MB address region in the 32-bit address space
2. 4 GB address region in the 64-bit address space
The default configuration is that of a 128 MB address region in the
32-bit address space. While this might be sufficient for most use-cases,
it is insufficient for supporting use-cases which require larger address
spaces. Therefore, switch to using the 64-bit address space with a 4 GB
address region.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20250422120042.3746004-2-s-vadapalli@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Remove disable-wp flag for eMMC nodes since this flag is
only applicable to SD according to the binding doc
(mmc/mmc-controller-common.yaml).
For eMMC, this flag should be ignored but lets remove
anyways to cleanup sdhci nodes.
Signed-off-by: Judith Mendez <jm@ti.com>
Reviewed-by: Moteen Shah <m-shah@ti.com>
Link: https://lore.kernel.org/r/20250429151454.4160506-4-jm@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
EMMC device is non-removable so add 'non-removable' DT
property to avoid having to redetect the eMMC after
suspend/resume.
Signed-off-by: Judith Mendez <jm@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20250429151454.4160506-3-jm@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The bootph-all flag was introduced in dt-schema
(dtschema/schemas/bootph.yaml) to define node usage across
different boot phases.
For eMMC and SD boot modes, voltage regulator nodes, io-expander
nodes, gpio nodes, and MMC nodes need to be present in all boot
stages, so add missing bootph-all phase flag to these nodes to
support SD boot and eMMC boot.
Signed-off-by: Judith Mendez <jm@ti.com>
Reviewed-by: Moteen Shah <m-shah@ti.com>
Link: https://lore.kernel.org/r/20250429151454.4160506-2-jm@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
PWM signals can be routed to the user expansion header on am625
SK and am62 lp sk. Enable eCAP0, eCAP1, eHRPWM1, and route the
output PWM signals to pins on J3 header.
Signed-off-by: Judith Mendez <jm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20250422000851.4118545-4-jm@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
PWM signals can be routed to the user expansion header on am62a7
SK. Enable eCAP0, eCAP1, eHRPWM1, and route the output PWM signals
to pins on J3 header.
Signed-off-by: Judith Mendez <jm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20250422000851.4118545-3-jm@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
PWM signals can be routed to the user expansion header on am62p5
SK. Enable eCAP0, eCAP1, eHRPWM0, eHRPWM1 and route the output PWM
signals to pins on J4 header.
Signed-off-by: Judith Mendez <jm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20250422000851.4118545-2-jm@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The phyCORE-AM68x/TDA4x [1] is a SoM (System on Module) featuring TI's
AM68x/TDA4x SoC. It can be used in combination with different carrier
boards. This module can come with different sizes and models for DDR,
eMMC, SPI NOR Flash and various SoCs from the AM68x/TDA4x (J721S2) family.
A reference carrier board design, called phyBOARD-Izar is used for the
phyCORE-AM68x/TDA4x development kit [2].
Supported features:
* Debug UART
* 2x SPI NOR Flash
* eMMC
* 2x Ethernet
* Micro SD card
* I2C EEPROM
* I2C RTC
* 2x I2C GPIO Expander
* LEDs
* USB 5 Gbit/s
* PCIe
For more details see the product pages for the SoM and the
development kit:
[1] https://www.phytec.eu/en/produkte/system-on-modules/phycore-am68x-tda4x/
[2] https://www.phytec.eu/en/produkte/development-kits/phyboard-izar/
Signed-off-by: Dominik Haller <d.haller@phytec.de>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Acked-by: Moteen Shah <m-shah@ti.com>
Link: https://lore.kernel.org/r/20250423133635.29897-2-d.haller@phytec.de
Signed-off-by: Nishanth Menon <nm@ti.com>
Add devicetree bindings for the AM68x based phyCORE-AM68x/TDA4x SoM
and the phyBOARD-Izar carrier board.
Signed-off-by: Dominik Haller <d.haller@phytec.de>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250423133635.29897-1-d.haller@phytec.de
Signed-off-by: Nishanth Menon <nm@ti.com>
Commit under Fixes corrected the "mux-reg-masks" property but did not
update the "length" field of the "reg" property to account for the
newly added register offsets which extend the region. Fix this.
Fixes: 38e7f9092e ("arm64: dts: ti: k3-j784s4-j742s2-main-common: Fix serdes_ln_ctrl reg-masks")
Cc: stable@vger.kernel.org
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20250423151612.48848-1-s-vadapalli@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Add the 5v0 supply that is provided over the display panel cable and
used by the LCD. This is required by "simple panels" or we get the
following warning from DTBS_CHECK:
k3-am654-gp-evm.dtb: display0: 'power-supply' is a required property
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20250421214620.3770172-4-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Now that the TI K3 AM654 system controller bindings also cover the
usage in the main domain, add its compatible to address dtbs_check
complains:
k3-am654-base-board.dtb: scm-conf@100000: compatible: ['syscon', 'simple-mfd'] is too short
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20250421214620.3770172-3-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Add the child nodes that can be found under this node. Then as done
for other similar devices (J7200 and J721s2) add support for the AM654
system controller to this binding.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20250421214620.3770172-2-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Fix hdmi-connector and tfp bridge node as per the bindings,
- Remove 'digital' property which is required for DVI connector not HDMI
- Add 'ti,deskew' property which is a required property
- Fix ports property for tfp410 bridge
- Change node names appropriately
Redefine the ports for dss and for k3-j721e-common-proc-board.dts, add
reg property for the port (@0) to get rid of dtbs_check warnings in
infotainment overlay when ports for dss are re-defined.
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20250424080328.57671-1-j-choudhary@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The USB0 instance of the USB controller on both the J742S2 EVM and the
J784S4 EVM supports a single USB interface at a time among the following:
1. USB3.1 Gen1 Type C interface
2. Two USB2.0 Type A interfaces via an on-board USB Hub.
By default, the USB3.1 Gen1 Type C interface is supported on both of the
EVMs. Enable the USB2.0 Type A interface by configuring the USB2.0_MUX_SEL
mux. Additionally, set the Dual-Role Mode to Host since a Type-A interface
is only associated with the Host Mode of operation.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20250409100853.4179934-1-s-vadapalli@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
main_gpio1 controls the voltage for the SDcard from 3.3v to 1.8v.
This is required for proper operation of SDcard through various boot
stages.
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20250411203950.2859356-1-nm@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
BeagleBoard.org PocketBeagle 2 is an upgraded version of the popular
PocketBeagle. It is based on Texas Instruments AM6232 or AM6254 SoC.
Its dual or quad A53 cores can provide higher performance than classic
PocketBeagle. The new design comes with pre-soldered headers, a
3-pin JST-SH 1.00mm UART debug port, a USB-C port, Texas Instruments
MSPM0L1105 Cortex-M0+ MCU for ADC, 512MB RAM, and a LiPo Battery
charger.
MSPM0L1105 firmware source:
https://openbeagle.org/pocketbeagle/mspm0-adc-eeprom
* EEPROM 24c32 emulation
* ADC ad7291 emulation
https://www.beagleboard.org/boards/pocketbeagle-2https://openbeagle.org/pocketbeagle/pocketbeagle-2
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Tested-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/r/20250415225940.3899486-2-robertcnelson@gmail.com
Signed-off-by: Nishanth Menon <nm@ti.com>
According to the AT24 EEPROM bindings the compatible string should
contain first the actual manufacturer, and second the corresponding
atmel model.
Add the atmel compatible fallback accordingly.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://lore.kernel.org/r/20250408202655.6329-1-francesco@dolcini.it
Signed-off-by: Nishanth Menon <nm@ti.com>
Add the node for the random number generator inside the crypto module.
Marked reserved since the default usage is with the RNG node being
controlled by OP-TEE.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20250401083246.3228964-1-mwalle@kernel.org
Signed-off-by: Nishanth Menon <nm@ti.com>
This region is used for controlling the function of the PCIe IP. It is
compatible with "ti,j784s4-pcie-ctrl", add this here and use it with
the PCIe node.
Signed-off-by: Andrew Davis <afd@ti.com>
[j-choudhary@ti.com: Add changes to k3-am642-evm-pcie0-ep.dtso]
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://lore.kernel.org/r/20250402113201.151195-6-j-choudhary@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
This region is used for controlling the function of the PCIe IP. It is
compatible with "ti,j784s4-pcie-ctrl", add this here and use it with
the PCIe node.
Signed-off-by: Andrew Davis <afd@ti.com>
[j-choudhary@ti.com: Add changes to k3-am68-sk-base-board-pcie1-ep.dtso]
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://lore.kernel.org/r/20250402113201.151195-5-j-choudhary@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
This region is used for controlling the function of the PCIe IP. It is
compatible with "ti,j784s4-pcie-ctrl", add this here and use it with
the PCIe node.
Signed-off-by: Andrew Davis <afd@ti.com>
[j-choudhary@ti.com: Add changes to k3-j7200-evm-pcie1-ep.dtso]
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://lore.kernel.org/r/20250402113201.151195-4-j-choudhary@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
This region is used for controlling the function of the PCIe IP. It is
compatible with "ti,j784s4-pcie-ctrl", add this here and use it with
the PCIe nodes.
Signed-off-by: Andrew Davis <afd@ti.com>
[j-choudhary@ti.com: Add changes to k3-j721e-evm-pcie1-ep.dtso]
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://lore.kernel.org/r/20250402113201.151195-3-j-choudhary@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Add a pattern property for pcie-ctrl which can be part of this controller.
Signed-off-by: Andrew Davis <afd@ti.com>
[j-choudhary@ti.com: Change description and add example]
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20250402113201.151195-2-j-choudhary@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The OV5640 device tree overlay incorrectly defined an I2C switch
instead of an I2C mux. According to the DT bindings, the correct
terminology and node definition should use "i2c-mux" instead of
"i2c-switch". Hence, update the same to avoid dtbs_check warnings.
Fixes: 635ed97151 ("arm64: dts: ti: k3-am62x: Add overlays for OV5640")
Cc: stable@vger.kernel.org
Signed-off-by: Yemike Abhilash Chandra <y-abhilashchandra@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Jai Luthra <jai.luthra@linux.dev>
Link: https://lore.kernel.org/r/20250415111328.3847502-8-y-abhilashchandra@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
