Fix the RS485 functionality, the RS485 RTS signal is active high on Ivy.
Fixes: f33a1f9a94 ("arm64: dts: freescale: imx95-verdin: Add Ivy carrier board")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add Zinnia Carrier Board mated with Verdin iMX95.
It features 1 x RS232, 1 x RS485, 1 x CAN, 3 x isolated digital I/O,
2 x GBit/s Ethernet, a mini PCIe slot with USB / SIM card connector
for a modem, USB and SD card interfaces.
Link: https://www.toradex.com/products/carrier-board/zinnia-carrier-board
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Some carrier board reuse the UART_2 control signals as GPIO, split
the pinctrl RTS/CTS in separated nodes to maximize flexibility.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add Zinnia Carrier Board mated with Verdin iMX8M Plus.
It features 1 x RS232, 1 x RS485, 1 x CAN, 3 x isolated digital I/O,
2 x GBit/s Ethernet, a mini PCIe slot with USB / SIM card connector
for a modem, USB and SD card interfaces.
Link: https://www.toradex.com/products/carrier-board/zinnia-carrier-board
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Some carrier board reuse the UART_2 control signals as GPIO, split
the pinctrl RTS/CTS in separated nodes to maximize flexibility.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add Zinnia Carrier Board mated with Verdin iMX8M Mini.
It features 1 x RS232, 1 x RS485, 1 x CAN, 3 x isolated digital I/O,
1 x GBit/s Ethernet, a mini PCIe slot with USB / SIM card connector
for a modem, USB and SD card interfaces.
Link: https://www.toradex.com/products/carrier-board/zinnia-carrier-board
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Some carrier board reuse the UART_2 control signals as GPIO, split
the pinctrl RTS/CTS in separated nodes to maximize flexibility.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add Toradex Verdin Zinnia carrier board mated with Verdin
iMX8M Plus, Verdin iMX8M Mini and Verdin iMX95.
Link: https://www.toradex.com/products/carrier-board/zinnia-carrier-board
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
IRQ_TYPE_xxx flags are not correct in the context of GPIO flags.
These are simple defines so they could be used in DTS but they will not
have the same meaning: IRQ_TYPE_EDGE_FALLING = 2 = GPIO_SINGLE_ENDED.
Correct the Type-C int-gpios to use proper flags, assuming the author of
the code wanted similar logical behavior:
IRQ_TYPE_EDGE_FALLING => GPIO_ACTIVE_LOW
Fixes: c4b4593ecb ("arm64: dts: imx8ulp-evk: enable usb nodes and add ptn5150 nodes")
Cc: stable@vger.kernel.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
MMU-700 supports TCU PMU and TBU PMU. There are one TCU PMU and
11 TBU PMUs, add them all.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Update SMMU reg size to 0x40000, because MMU-700 TCU occupies 4 pages with
each page 64KB and the last page is reserved.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Support Mali G310 GPU on i.MX952 board. Describe this GPU in the DT.
Include dummy GPU voltage regulator and OPP tables.
A hardware GPU auto clock‑gating mechanism has been introduced, enabling
GPUMIX to automatically manage the GPU clock. This improves overall
response time.
Signed-off-by: Guangliu Ding <guangliu.ding@nxp.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add device tree support for the Variscite Symphony carrier board with
the VAR-SOM-MX91 system on module.
The Symphony board includes
- uSD Card support
- USB ports and OTG
- Additional Gigabit Ethernet interface
- Uart, ADC and I2C interfaces
- GPIO Expanders
- RTC module
- TPM module
- CAN peripheral
Link: https://variscite.com/carrier-boards/symphony-board/
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add device tree support for the Variscite VAR-SOM-MX91 system on module.
This SOM is designed to be used with various carrier boards.
The module includes:
- NXP i.MX91 MPU processor
- Up to 2GB of LPDDR4 memory
- Up to 128GB of eMMC storage memory
- Integrated 10/100/1000 Mbps Ethernet Transceiver
- Codec audio WM8904
- WIFI6 dual-band 802.11ax/ac/a/b/g/n with optional 802.15.4 and Bluetooth
Only SOM-specific peripherals are enabled by default. Carrier board
specific interfaces are left disabled to be enabled in the respective
carrier board device trees.
Link: https://variscite.com/system-on-module-som/i-mx-9/i-mx-91/var-som-mx91/
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add DT compatible strings for Variscite VAR-SOM-MX91 SoM and Symphony
development carrier Board.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
This reverts commit 39e4189d9d.
The board uses SDHC VSELECT to automatically switch between 1.8v and
3.3v. It does not use GPIO to control the PMIC SD_VSEL signal.
The original commit intends to read back SD_VSEL value from GPIO,
but it is wrong. When MUX is configured as SDHC VSELECT, it is
impossible to read back the value from GPIO controller. Setting SION
could only enable the input path for the mux function. It could not
redirect the input to GPIO.
Fixes: 39e4189d9d ("arm64: dts: imx8mp-kontron: Add support for reading SD_VSEL signal")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
This reverts commit 8472751c4d.
The board uses SDHC VSELECT to automatically switch between 1.8v and
3.3v. It does not use GPIO to control the PMIC SD_VSEL signal.
The original commit intends to read back SD_VSEL value from GPIO,
but it is wrong. When MUX is configured as SDHC VSELECT, it is
impossible to read back the value from GPIO controller. Setting SION
could only enable the input path for the mux function. It could not
redirect the input to GPIO.
And value "0x40000d0" is wrong, SION is BIT30, not BIT26.
Fixes: 8472751c4d ("arm64: dts: imx8mm-kontron: Add support for reading SD_VSEL signal")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
The PHYTEC phyBOARD Pollux comes with a HDMI port on the base board.
Add the required device-tree nodes to enable support for it, including
both the video and the audio paths.
Signed-off-by: Paul Kocialkowski <paulk@sys-base.io>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
GPIO_ACTIVE_x flags are not correct in the context of interrupt flags.
These are simple defines so they could be used in DTS but they will not
have the same meaning:
1. GPIO_ACTIVE_HIGH = 0 => IRQ_TYPE_NONE
2. GPIO_ACTIVE_LOW = 1 => IRQ_TYPE_EDGE_RISING
Correct the interrupt flags, assuming the author of the code wanted the
same logical behavior behind the name "ACTIVE_xxx", this is:
ACTIVE_LOW => IRQ_TYPE_LEVEL_LOW
Fixes: bf68c18150 ("arm64: dts: imx8mp-ab2: add support for NXP i.MX8MP audio board (version 2)")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Reviewed-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
GPIO_ACTIVE_x flags are not correct in the context of interrupt flags.
These are simple defines so they could be used in DTS but they will not
have the same meaning:
1. GPIO_ACTIVE_HIGH = 0 => IRQ_TYPE_NONE
2. GPIO_ACTIVE_LOW = 1 => IRQ_TYPE_EDGE_RISING
Correct the interrupt flags, assuming the author of the code wanted the
same logical behavior behind the name "ACTIVE_xxx", this is:
ACTIVE_LOW => IRQ_TYPE_LEVEL_LOW
Fixes: 5eb7405db9 ("arm64: dts: imx8mn: Add ifm VHIP4 EvalBoard v1 and v2")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Reviewed-by: Marek Vasut <marex@nabladev.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
GPIO_ACTIVE_x flags are not correct in the context of interrupt flags.
These are simple defines so they could be used in DTS but they will not
have the same meaning:
1. GPIO_ACTIVE_HIGH = 0 => IRQ_TYPE_NONE
2. GPIO_ACTIVE_LOW = 1 => IRQ_TYPE_EDGE_RISING
Correct the interrupt flags, assuming the author of the code wanted the
same logical behavior behind the name "ACTIVE_xxx", this is:
ACTIVE_LOW => IRQ_TYPE_LEVEL_LOW
Fixes: 5eb7405db9 ("arm64: dts: imx8mn: Add ifm VHIP4 EvalBoard v1 and v2")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Reviewed-by: Marek Vasut <marex@nabladev.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add device tree support for the Variscite Sonata carrier board with the
DART-MX93 system on module.
The Sonata board includes
- uSD Card support
- USB ports and OTG
- Additional Gigabit Ethernet interface
- Uart, SPI and I2C interfaces
- GPIO Expanders
- RTC module
- TPM module
- CAN peripherals
Link: https://variscite.com/carrier-boards/sonata-board/
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add device tree support for the Variscite DART-MX93 system on module.
This SOM is designed to be used with various carrier boards.
The module includes:
- NXP i.MX93 MPU processor
- Up to 2GB of LPDDR4 memory
- Up to 128GB of eMMC storage memory
- Integrated 10/100/1000 Mbps Ethernet Transceiver
- Codec audio WM8904
- WIFI6 dual-band 802.11ax/ac/a/b/g/n with optional 802.15.4 and Bluetooth
Only SOM-specific peripherals are enabled by default. Carrier board
specific interfaces are left disabled to be enabled in the respective
carrier board device trees.
Link: https://variscite.com/system-on-module-som/i-mx-9/i-mx-93/dart-mx93/
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add DT compatible strings for Variscite DART-MX93 SoM and Variscite
development carrier Board.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
On the Toradex SMARC iMX95, the WiFi UART signals are shared with the
JTAG. The WIFI_UART_EN signal is used to select between these
two functions. A GPIO hog is used to select the UART function by
default. This DT file is going to be used by both Linux and the boot
firmware, and the boot firmware will configure the GPIO hog way before
the Linux kernel is booted, therefore there is no actual race condition
between the Linux kernel BT UART driver and GPIO hog probe.
Configure WIFI_UART_EN as a gpio-hog driven high.
Signed-off-by: Franz Schnyder <franz.schnyder@toradex.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
The Toradex SMARC iMX95 uses the MAYA-W260 WiFi/Bluetooth module, which
uses the UART interface for Bluetooth.
Add UART support to enable bluetooth functionality on the MAYA-W260.
Signed-off-by: Franz Schnyder <franz.schnyder@toradex.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
The Toradex SMARC iMX95 has four exposed serial interfaces, one of these
is SER2, which supports RTS/CTS.
Add UART support for SMARC SER2.
Signed-off-by: Franz Schnyder <franz.schnyder@toradex.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Due to missing workaround for "ERR050104: Arm/A53: Cache coherency issue"
disable the whole Cortex-A72 cluster.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
This adds support for TQMa8QM module on MBa8x board, based on i.MX8 SoC.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
The CSI-2 in the i.MX8ULP is almost identical to the version present
in the i.MX8QXP/QM and is routed to the ISI. Add both the ISI and CSI
nodes and mark them as disabled by default since capture is dependent
on an attached camera.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Guoniu Zhou <guoniu.zhou@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
SION is BIT(30), not BIT(26). Correct it.
Fixes: 7ece3cbc8b ("arm64: dts: colibri-imx8x: Add atmel pinctrl groups")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
RGB enable pin, labeled as RGBSEL, is a board-level enable signal on
the Sonata carrier board.
The two PCA6408 GPIO expanders depend on this signal being asserted, so
model it as a fixed regulator and use it as their vcc-supply.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add gpio-line-names for GPIOs with a defined board-level
function on the PHYTEC phyBOARD-Segin-i.MX93.
Signed-off-by: Florijan Plohl <florijan.plohl@norik.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add gpio-line-names for GPIOs with a defined board-level
function on the PHYTEC phyBOARD-Nash-i.MX93.
Signed-off-by: Florijan Plohl <florijan.plohl@norik.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add gpio-line-names for GPIOs with a defined board-level
function on the PHYTEC phyCORE-i.MX93 SoM.
Signed-off-by: Florijan Plohl <florijan.plohl@norik.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add gpio-line-names for GPIOs with a defined board-level
function on the PHYTEC phyBOARD-Segin-i.MX91.
Signed-off-by: Florijan Plohl <florijan.plohl@norik.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add gpio-line-names for GPIOs with a defined board-level
function on the PHYTEC phyCORE-i.MX91 SoM.
Signed-off-by: Florijan Plohl <florijan.plohl@norik.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add i.MX91 9x9 Quick Start Board support.
- Enable ADC1.
- Enable lpuart1.
- Enable network eqos.
- Enable I2C bus and children nodes under I2C bus.
- Enable USB and related nodes.
- Enable uSDHC1 and uSDHC2.
- Enable Watchdog3.
The board description can refer to the following link:
https://www.nxp.com/design/design-center/development-boards-and-designs/IMX91QSB
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
The clock-frequency property is not implemented. Remove it to clean up the
device tree.
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
The clock-frequency property is not implemented. Remove it to clean up the
device tree.
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
The clock-frequency property is not implemented. Remove it to clean up the
device tree.
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add compatible string for i.MX91 9x9 Quick Start Board.
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
i.MX Audio Board is a configurable and functional audio processing
platform. Integrating a variety of audio input and output interfaces into
the system, the i.MX Audio Board supports HDMI input, HDMI eARC,
S/PDIF I/O, 2-ch ADC line-in, 24-ch DAC line-out and more. Based on these
features, rich audio application cases can be realized.
This is a basic device tree supporting with i.MX95 15x15 SoC and Audio
board (version 2).
- Six Cortex-A55
- NXP PCAL6416 GPIO expanders
- RGB LEDs via GPIO expander
- LPI2C1, LPI2C2, LPI2C3 controllers
- LPUART1 (console)
- USDHC1 (eMMC), USDHC2 (SD)
- Three DAC (AK4458)
- One ADC (AK5552)
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Introduce a new DT compatible string for the NXP i.MX95 15x15 audio board
(version 2).
i.MX Audio Board is a configurable and functional audio processing
platform. Integrating a variety of audio input and output interfaces into
the system, the i.MX Audio Board supports HDMI input, HDMI eARC,
S/PDIF I/O, 2-ch ADC line-in, 24-ch DAC line-out and more. Based on these
features, rich audio application cases can be realized.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Raspberry Pi 3B by marking the VEC clk critical so it doesn't get
turned off and hang the bus.
-----BEGIN PGP SIGNATURE-----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=JtUn
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fix from Stephen Boyd:
"One more fix for the merge window to avoid a boot hang on
Raspberry Pi 3B by marking the VEC clk critical so that it
doesn't get turned off and hang the bus"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: bcm: rpi: Mark VEC clock as CLK_IGNORE_UNUSED
- Drop class_create() for the "tsm" class
-----BEGIN PGP SIGNATURE-----
iIYEABYKAC4WIQSbo+XnGs+rwLz9XGXfioYZHlFsZwUCae40aBAcZGpid0BrZXJu
ZWwub3JnAAoJEN+KhhkeUWxn/F0BAIpdhnq3TbPMC6Pj0q3DfcXpP+LPD0pqqIom
TwsQVZJCAP4rYVEbIbgeXvkilr7Fpcs2AXbidR/ggBsR3lyVBSNhAA==
=ZK/r
-----END PGP SIGNATURE-----
Merge tag 'tsm-for-7.1' of git://git.kernel.org/pub/scm/linux/kernel/git/devsec/tsm
Pull PCIe TSP update from Dan Williams:
"A small update for the TSM core. It is arguably a fix and coming in
late as I have been offline the past few weeks:
- Drop class_create() for the 'tsm' class"
* tag 'tsm-for-7.1' of git://git.kernel.org/pub/scm/linux/kernel/git/devsec/tsm:
virt: coco: change tsm_class to a const struct
- kbuild: builddeb - avoid recompiles for non-cross-compiles
Avoid triggering complete rebuilds for non-cross-compile Debian
package builds by only triggering the rebuild of host tools for
actual cross-compile builds.
- kbuild: Never respect CONFIG_WERROR / W=e to fixdep
Avoid spurious rebuilds of fixdep w/ and w/o -Werror during a single
kbuild invocation by never respecting CONFIG_WERROR for fixdep.
Cc: Masahiro Yamada <masahiroy@kernel.org>
Cc: Mathias Krause <minipli@grsecurity.net>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Thomas Weißschuh <linux@weissschuh.net>
-----BEGIN PGP SIGNATURE-----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=yCeR
-----END PGP SIGNATURE-----
Merge tag 'kbuild-fixes-7.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kbuild/linux
Pull Kbuild fixes from Nicolas Schier:
- builddeb - avoid recompiles for non-cross-compiles
Avoid triggering complete rebuilds for non-cross-compile Debian
package builds by only triggering the rebuild of host tools for
actual cross-compile builds
- Never respect CONFIG_WERROR / W=e to fixdep
Avoid spurious rebuilds of fixdep w/ and w/o -Werror during a single
kbuild invocation by never respecting CONFIG_WERROR for fixdep
* tag 'kbuild-fixes-7.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kbuild/linux:
kbuild: Never respect CONFIG_WERROR / W=e to fixdep
kbuild: builddeb - avoid recompiles for non-cross-compiles
Subsystem:
- add data_race() in rtc_dev_poll()
Drivers:
- remove i2c_match_id usage
- abx80x: Disable alarm feature if no interrupt attached
- ti-k3: support resuming from IO DDR low power mode
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEBqsFVZXh8s/0O5JiY6TcMGxwOjIFAmntBg4ACgkQY6TcMGxw
OjL+5A/7BHJ1q8BCJwhHHa0XRQcwB4afZehSB0qasNbbAqJFgzrwZfg6mVXhXO3Y
hry0SjzmFkCL9h6jckye2hPFjJsiaBC0Tauvmun6litrPnOrK+IK+P+Q7iKPap3Q
5bSy+tDJXx3F3f+6LgDSVnrQFI3Q+nMHY/b1IWJkGW9Jpg/QlhU3UazN1kwu9Hyn
nBvCczHyTYlSqaDSFUkQRXLfzXiMU16/iHzwsJZmOU03HNb1IF0Ngi8fIrPf1OIK
2ZoyLzH0O0u+k10M+Sq/A2LKsgjnBOlu/L4iJUOKlhuq3Ze4/SY+C3IP+XbMyYF5
EZ7pxPz66/WLzOpVx1xaSLpFiRBcCgbvwT2TY3P7e8A09AGye+AB+cqdKF9r9mX2
p57cv2ZkZs/bGEjee2rSs7TTT4vZUhaa4SS6C4xrKIIoymFyKlh6E5fzWNUk4zua
oN0djSSbtdIpSErIrlxp5xiITCIjSTZMVQKccs3qV5QhzNH8zsUPwwCM1cDawALC
/HP6KnYmt6fTx3PS4BPVnMCQqSu425tvMhy5nvjbgdFVPd+CgOEAW6qO82nI3UFY
KDNP4O224CVuOeX2WAU6+gOCTwqxg6rbjASAGGFOl6ox8eW555wpedVls0Y8oUQm
z0O+gK33L/0hrw5Qnhh2If4S7gyNwWwVif2Gosf5ODRQ6LM5UOg=
=mY/t
-----END PGP SIGNATURE-----
Merge tag 'rtc-7.1' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"Subsystem:
- add data_race() in rtc_dev_poll()
Drivers:
- remove i2c_match_id usage
- abx80x: Disable alarm feature if no interrupt attached
- ti-k3: support resuming from IO DDR low power mode"
* tag 'rtc-7.1' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
rtc: abx80x: Disable alarm feature if no interrupt attached
rtc: ntxec: fix OF node reference imbalance
rtc: pic32: allow driver to be compiled with COMPILE_TEST
rtc: ti-k3: Add support to resume from IO DDR low power mode
rtc: cmos: Use platform_get_irq_optional() in cmos_platform_probe()
dt-bindings: rtc: add olpc,xo1-rtc to trivial-rtc
dt-bindings: rtc: sc2731: Add compatible for SC2730
rtc: add data_race() in rtc_dev_poll()
rtc: armada38x: zalloc + calloc to single allocation
dt-bindings: rtc: isl12026: convert to YAML schema
dt-bindings: rtc: microcrystal,rv3028: Allow to specify vdd-supply
rtc: max77686: convert to i2c_new_ancillary_device
dt-bindings: rtc: mpfs-rtc: permit resets
rtc: rx8025: Remove use of i2c_match_id()
rtc: rv8803: Remove use of i2c_match_id()
rtc: rs5c372: Remove use of i2c_match_id()
rtc: pcf2127: Remove use of i2c_match_id()
rtc: m41t80: Remove use of i2c_match_id()
rtc: abx80x: Remove use of i2c_match_id()
