When the I2C controller is disabled, no communication is expected to
take place. Without traffic on the bus, the pull-up is unnecessary.
Both the vendor kernel for this platform and DTs of other SoCs in
upstream concur this logic. Change the default and clean up now-NOP
overrides.
Fixes: 0fee55fc0d ("arm64: dts: qcom: msm8998: Add I2C pinctrl and fix BLSP2_I2C naming")
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260717-topic-june26_dts_fixes-v2-1-797cd46e5d9f@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add a node for the GX clock controller, which provides a power domain to
consumers.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Jagadeesh Kona <jagadeesh.kona@oss.qualcomm.com>
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Link: https://lore.kernel.org/r/20260417-milos-gxclkctl-v3-3-08f5988c43a2@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
taoyao originally redefined adsp_rpc_remote_heap_mem at a fixed address
to avoid overlapping with cdsp_mem, since kodiak.dtsi's version was a
fixed-address at the time.
kodiak.dtsi now defines adsp_rpc_remote_heap_mem as a dynamically
allocated "shared-dma-pool" region instead, which removes the fixed
address entirely and so cannot overlap with cdsp_mem. This makes the
override unnecessary.
Remove the taoyao-local /delete-node/ and static reg-based redefinition,
and inherit the definition from kodiak.dtsi instead.
Fixes: 28705df5d0 ("arm64: dts: qcom: sm7325: Add Xiaomi 12 Lite 5G (taoyao) DTS")
Signed-off-by: Stanislav Zaikin <zstaseg@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260730085422.631896-1-zstaseg@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Describe the ADSP Generic Packet Router (GPR) devicetree node as
part of audio subsystem on Qualcomm Eliza SoC.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260724-dts-qcom-eliza-add-gpr-v3-1-2595beb0cdec@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Even though the EVK comes with 3 Type-C ports, the Eliza EVK only has
one USB controller and a single set of PHYs, which are connected to
the port marked as JUSB.
Also, the EVK comes with an SD card slot.
So describe the PMIC GLINK node, the connector graph, the PHYs and repeater
supplies and enable the USB controller.
Also enable the second SD host controller, describe the card detect GPIO
and the board specific supplies.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260724-dts-qcom-eliza-cqs-evk-enable-usb-sdcard-v3-1-eadf9da69226@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
One selects in this schema captures "^qcom,.*sa[0-9]+.*$" compatibles,
because there are SAxxxx Qualcomm SoCs. Unfortunately there is also
WSA8810 and WSA8855 I2C speakers, so they need listing too.
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260721-dt-bindings-qcom-soc-naming-v3-4-8f275c9d3412@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The schema checking for expected naming patterns for SoC IP block nodes
was really incomplete and was checking only nodes with single
compatible.
Fix this by changing "select:" to "contains:" so every
node, except root nodes, having at least one matching compatible will be
evaluated.
This however will evaluate nodes which have some generic fallbacks (e.g.
syscon), thus the schema for expected compatible should also have
"contains:" (with "anyOf:").
These two above are the only functional changes in this commit and the
rest of the diff is indentation change. None of the patterns are
changed (neither in "Preferred naming style" group nor in "Legacy
namings"), none of the compatibles are affected. Basically the second
part of the diff is (simplifying):
properties:
compatible:
- oneOf:
- ......
+ contains:
+ anyOf:
+ ......
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260721-dt-bindings-qcom-soc-naming-v3-3-8f275c9d3412@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The schema misses several old style compatibles with SoC component
trailing in the compatible (qcom,IP-SoC):
- qcom,apss-wdt-x1e80100
- qcom,apss-wdt-xxx, qcom,rpm-xxx and qcom,scm-xxx for SoC with code
names (like qcom,rpm-shikra)
- qcom,kpss-gcc-xxx
- qcom,rpmcc-xxx
- qcom,tcsr-xxx
- qcom,usb-hs-phy-xxx
It also missed qcom,ipq806x-ahci.
None of these were flagged by schema, because they were used with
fallbacks and the schema checks only for single compatibles.
Nevertheless document them for complete picture and for future change,
which will apply the schema to fallbacks as well.
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260721-dt-bindings-qcom-soc-naming-v3-2-8f275c9d3412@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Grow the schema checking for proper SoC compatible naming style with
recently upstreamed new Qualcomm SoCs: Eliza, Kaanapali, Hawi, Mahua,
Maili, Nord and Shikra. The list covers only SoC IP blocks, thus no
Hamoa or Talos in the names, because these are codenames but not used
for SoC IP block naming.
Since switching from model numbers to codenames, this list with explicit
codenames will have to grow and list them all in order for the schema to
work. It feels like a churn, but the compatible naming is still mess,
for example, the schema pci/qcom,pcie-x1e80100.yaml with a legacy naming
vendor,IP-SoC (qcom,pcie-x1e80100) received a new compatible with new
style (qcom,glymur-pcie).
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260721-dt-bindings-qcom-soc-naming-v3-1-8f275c9d3412@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add cooling-cells property to the CPU nodes to support
cpufreq cooling devices.
Signed-off-by: Haritha S K <haritha.k@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260724-eliza-cpufreq-v1-1-38f01e47f0f1@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The SoC Control Processor (SoCCP) is a small RISC-V MCU that controls
USB Type-C, battery charging, and various other functions on Qualcomm SoCs.
Add the nodes required to enable SoCCP on Glymur/Mahua SoCs.
Signed-off-by: Sibi Sankar <sibi.sankar@oss.qualcomm.com>
Co-developed-by: Ananthu C V <ananthu.cv@oss.qualcomm.com>
Signed-off-by: Ananthu C V <ananthu.cv@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260709-glymur-soccp-v6-4-16f70227547d@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The currently listed SoCCP and SoCCP DTB reserved memory regions
don't align with the memory requested by the SoCCP Firmware. Fix
this by updating the SoCCP/SoCCP DTB memory regions to reflect the
memory region requirements of the SoCCP firmware, as described in
the Glymur v21 memory map release.
Fixes: 41b6e8db40 ("arm64: dts: qcom: Introduce Glymur base dtsi")
Signed-off-by: Ananthu C V <ananthu.cv@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260709-glymur-soccp-v6-3-16f70227547d@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Mahua has a different QREF topology from Glymur. Override the TCSR
compatible to qcom,mahua-tcsr in mahua.dtsi, and wire up the required
LDO supplies on the CRD board.
Unlike the other PCIe controllers, PCIe5 PHY on Mahua gets its refclk
from the CXO0 pad directly and requires no QREF clkref_en voting. Hence,
point its ref clock at RPMH_CXO_CLK.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Qiang Yu <qiang.yu@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260721-tcsr_qre_0721-v10-7-d2fa68c63b78@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The TCSR clkref_en clocks gate the QREF block which provides reference
clocks to the PCIe PHYs. Wire up the LDO supplies required by the QREF
and refgen blocks on the CRD board.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Qiang Yu <qiang.yu@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260721-tcsr_qre_0721-v10-6-d2fa68c63b78@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The GCC GDSCs on Glymur are backed by the RPMh CX power domain. Without
describing that parent domain, consumers of GCC-provided GDSCs can enable
their local domain without causing the required CX vote to be held.
Add the CX power-domain reference to the GCC node so votes from GCC GDSC
consumers can propagate to RPMh CX.
Fixes: 41b6e8db40 ("arm64: dts: qcom: Introduce Glymur base dtsi")
Signed-off-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260715-glymur-fix-gcc-cx-scaling-v3-3-72eb5adad156@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
According to user manual / programming guide there is no separate PCIe
phy 3A and 3B, but one 8-lane QMP PCIe Gen5 PHY which consists of two
4-lane blocks. This is also visible in memory map, where the 0xf00000
is marked as the main block with additional sub blocks for each 4-lane
phys.
Describing the sub phys without the rest is not correct from hardware
description, even if it works.
Link: https://lore.kernel.org/r/20260420-optimistic-unnatural-stingray-80da35@quoll/
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260609141608.354186-2-krzysztof.kozlowski@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Glymur has a True Random Number Generator, add the node with the correct
compatible set.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Harshal Dev <harshal.dev@oss.qualcomm.com>
Tested-by: Kuldeep Singh <kuldeep.singh@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260424-glymur_trng_enablement-v2-2-0603cbe68440@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Embedded Trace Router(ETR) is working as a DDR memory sink to collect
tracing data from source device and the CTCU device serves as the
control unit for the ETR device.
Signed-off-by: Jie Gan <jie.gan@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260714-add-ctcu-etr-for-glymur-v1-1-791de63c0713@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Centrally define the endpoints to let device DTs that describe PCIe
devices and/or M.2 connectors refer to them without error-prone
duplication.
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260716-topic-smb2370_port2-v1-2-83d02b2ba4b0@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
It's absent on laptops that only have 2 type-C ports (the majority so
far, including the CRD). Keep it disabled by default, following
established practice from the previous generation.
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Gopikrishna Garmidi <gopikrishna.garmidi@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260716-topic-smb2370_port2-v1-1-83d02b2ba4b0@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The Eliza MTP uses a Goodix GT9916 touchscreen controller connected
over SPI.
Describe the controller, its power supply, interrupt and reset GPIOs to
enable touchscreen support.
Signed-off-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260708-dts-qcom-eliza-mtp-enable-ts-v1-1-372020a7a86b@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The Iris block on X1P differs from SM8550/X1E in its clock configuration
and requires a dedicated OPP table. The node inherited from the X1E cannot
be reused directly, and the fallback compatible "qcom,sm8550-iris" cannot
be applied.
Override the inherited clocks, clock-names, and operating points, and
replaces them with the X1P42100-specific definitions. A new OPP table
is provided to support the correct performance levels on this platform.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dikshita Agarwal <dikshita.agarwal@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Wangao Wang <wangao.wang@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260713-enable_iris_on_purwa-v9-1-633d7b87f0c9@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
USB QMP PHY is a possible handler of altmode switching, so add this
property.
Signed-off-by: Esteban Urrutia <esteuwu@proton.me>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260711-sm8450-qol-dts-v2-2-5eb2e86468c5@proton.me
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
These nodes are not present on downstream device trees and only take memory
away from the AP.
No crashes occur without these nodes, so remove them.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Esteban Urrutia <esteuwu@proton.me>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260711-sm8450-qol-dts-v2-1-5eb2e86468c5@proton.me
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add Hawi SoC and its reference boards to the Qualcomm binding.
Signed-off-by: Mukesh Ojha <mukesh.ojha@oss.qualcomm.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260617151602.2018579-1-mukesh.ojha@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The SCMI protocol@13 (Performance Domain Management) node was using
performance/power domain, not a clock. This was using the older
mechanism for passing the SCMI performance domain index to
scmi-cpufreq, which predates the #power-domain-cells support added
in commit 92b2028b00 ("cpufreq: scmi: Add support to parse
domain-id using #power-domain-cells").
Switch to #power-domain-cells to match all other Qualcomm platforms
(sm8750, glymur, hamoa) and align with the semantically correct
representation.
Signed-off-by: Mukesh Ojha <mukesh.ojha@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260508082729.37674-1-mukesh.ojha@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add remoteproc PAS loader for SoCCP with its SMP2P. On Kaanapali, it is
brought up by bootloader.
Signed-off-by: Jingyi Wang <jingyi.wang@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260709-knp-soccp-dt-v2-1-6e2bfca96088@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The Arduino Monza board has a TI INA232 current/power monitor connected
on I2C12 at address 0x40. It is used to measure the board supply current
through a 2 milliohms shunt resistor.
Signed-off-by: Loic Poulain <loic.poulain@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260611-monza-ina232-v2-3-e4375ce652d0@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The l12b and l15b supplies are used by components that are not (fully)
described (and some never will be) and must never be disabled.
Mark the regulators as always-on to prevent them from being disabled,
for example, when consumers probe defer or suspend.
Note that these supplies currently have no consumers described in
mainline for dell-thena beyond the audio codec (vdd-buck/vdd-rxtx/
vdd-io on wcd938x), which can release them when the codec goes idle.
The board-level gpio-fixed regulators that feed the Type-C retimer's
VDDIO and other rails are not described with a vin-supply link, so
the kernel cannot keep their parent LDOs alive on its own.
This mirrors the same change Johan Hovold applied to every other
X1E80100 board in a March 2025 series; commit 63169c07d7
("arm64: dts: qcom: x1e80100-dell-xps13-9345: mark l12b and l15b always-on")
is representative. The dell-thena board file was introduced four months
later and did not inherit that change; this patch closes the gap.
Fixes: e7733b4211 ("arm64: dts: qcom: Add support for Dell Inspiron 7441 / Latitude 7455")
Cc: stable@vger.kernel.org
Signed-off-by: Michael Scott <mike.scott@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Acked-by: Val Packett <val@packett.cool>
Link: https://lore.kernel.org/r/20260521010935.1333494-4-mike.scott@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The OPP table for the Iris core is wrong, it copies the VDD table from
the downstream kernel, but that table is written for the
video_cc_mvs0_clk_src, while the upstream uses video_cc_mvs0_clk for OPP
rate setting (which is clk_src divided by 3). Specify correct
frequencies in the OPP table.
Fixes: fa245b3f06 ("arm64: dts: qcom: sm8250: Add venus DT node")
Reported-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dikshita Agarwal <dikshita.agarwal@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Vishnu Reddy <busanna.reddy@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260604-iris-venus-fix-sm8250-v7-2-7bd2f0e5bae8@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add RX and TX clocks for the IPQ5018 GEPHY to enable the datapath.
Fixes: f5f2b835e3 ("arm64: dts: qcom: ipq5018: Add GE PHY to internal mdio bus")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://lore.kernel.org/r/20260608-ipq5018-gephy-clocks-v4-3-fb2ccd56894b@outlook.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Document the Sony Xperia M2, which is a smartphone based on the
Qualcomm MSM8926 SoC.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Erikas Bitovtas <xerikasxx@gmail.com>
Link: https://lore.kernel.org/r/20260610-yukon-eagle-v4-1-763d5698bd2c@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The correct CMN PLL reference clock rate for IPQ5018 is 4.8 GHz.
The CMN PLL driver did not account for the ref clock divider which is 2
for IPQ5018. Therefore, the computed rate was twice the actual output.
With the driver now accounting for the CMN PLL reference clock
divider (commit: 88c543fff7), set the correct reference clock rate.
Fixes: c006b249c5 ("arm64: dts: ipq5018: Add CMN PLL node")
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Acked-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260521-ipq5018-cmn-pll-rate-fix-v2-1-04b28a92e0f2@outlook.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
An error in dmesg shows there is a mismatch between controller and DT
dout-ports.
Add PCM_OUT port to fix this.
Signed-off-by: Esteban Urrutia <esteuwu@proton.me>
Link: https://lore.kernel.org/r/20260622-sm8450-qol-v1-4-37e2ee8df9da@proton.me
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Embedded Trace Router(ETR) is working as a DDR memory sink to collect
tracing data from source device and the CTCU device serves as the
control unit for the ETR device.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Jie Gan <jie.gan@oss.qualcomm.com>
Reviewed-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Acked-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20260204-enable-ctcu-and-etr-v3-3-0bb95c590ae1@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Embedded Trace Router(ETR) is working as a DDR memory sink to collect
tracing data from source device.
The CTCU serves as the control unit for the ETR device, managing its
behavior to determine how trace data is collected.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Jie Gan <jie.gan@oss.qualcomm.com>
Reviewed-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Acked-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20260204-enable-ctcu-and-etr-v3-2-0bb95c590ae1@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Document the platforms that fallback to using the qcom,sa8775p-ctcu
compatible for probing.
Signed-off-by: Jie Gan <jie.gan@oss.qualcomm.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Acked-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20260204-enable-ctcu-and-etr-v3-1-0bb95c590ae1@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The &pmh0101_gpios node is extended twice in glymur-crd.dtsi. The first
extension defines the nvme_reg_en pinctrl state for the NVMe regulator
enable GPIO (gpio14), and the second adds key_vol_up_default for the
volume-up key (gpio6).
Merge both pinctrl states into a single &pmh0101_gpios block to avoid
the duplicate node extension.
No functional change intended.
Fixes: a5ad8a8e47 ("arm64: dts: qcom: Commonize Glymur CRD DTSI")
Signed-off-by: Gopikrishna Garmidi <gopikrishna.garmidi@oss.qualcomm.com>
Reviewed-by: Pankaj Patil <pankaj.patil@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260602-merge-duplicate-pmh0101-gpios-node-v2-1-251107b3d9fe@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add support for camera clock controller for camera clients to
be able to request for camera clocks on Glymur SoC's.
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Jagadeesh Kona <jagadeesh.kona@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260624-glymur_camcc-v5-3-a321df74b1a1@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add DTS for the Vicharak Axon Mini board based on the Qualcomm
QCS6490 SoC.
This adds debug UART, eMMC, UFS, SDIO WLAN, USB 2.0 host, PCIe
support along with regulators.
The UFS ICE block is kept disabled because enabling it currently causes
an SError during qcom_ice_create() on this board. UFS works without ICE.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Ajit Singh <blfizzyy@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260624125443.18729-4-blfizzyy@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The Vicharak Axon Mini is a single-board computer based on the
Qualcomm QCM6490 platform.
Add the top-level compatible string for this board.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Ajit Singh <blfizzyy@gmail.com>
Link: https://lore.kernel.org/r/20260624125443.18729-3-blfizzyy@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
