This device is used for 'sound-dai' and needs #sound-dai-cells. dtbs_check
raises a warning regarding sound_dai_property.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add the overlay for the Tianma TM070JVHG33 LVDS display.
Signed-off-by: Martin Schmiedel <Martin.Schmiedel@tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add the overlay for the Tianma TM070JVHG33 LVDS display.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add the overlay for the Tianma TM070JVHG33 LVDS display.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Correct spaces or mix of tabs+spaces into proper tab-indented lines.
No functional impact (same DTB).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Reviewed-by: Ghennadi Procopciuc <ghennadi.procopciuc@oss.nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Correct spaces or mix of tabs+spaces into proper tab-indented lines and
remove other whitespace violations. No functional impact (same DTB).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Fix the Ethernet PHY description on the DART-MX9 Sonata boards.
The GPIO previously described as the PHY reset line is actually a
board-level enable signal required by the PHY. Model it accordingly and
remove the incorrect reset GPIO description from the PHY nodes.
On i.MX91 and i.MX93 the signal is described as a fixed regulator,
whereas the existing regulator description on i.MX95 is reused.
Keeping the PHY enable asserted during boot ensures that Ethernet
initialization completes successfully.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
The first USB port features a Type-C connector with dual data role
and dual power role capabilities. Add the Type-C device node and
enable the corresponding USB controller and phy node.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Switch to use flattened model for USB3 controller. To enable USB
controller with restricted DMA access range to work correctly, add a
simple-bus to constrain the dma address.
Note:
This changes the USB controller compatible string from "fsl,imx95-dwc3"
to "nxp,imx95-dwc3". This requires a kernel with CONFIG_USB_DWC3_IMX
enabled; otherwise, the new DTB will not be compatible with older one.
As i.MX95 is a new SoC and is still under development, it's acceptable
at development early phase.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
The first USB port features a Type-C connector with dual data role
and dual power role capabilities. Add the Type-C device node and
enable the corresponding USB controller and phy node.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Update the SIUL2 pinctrl node to describe the additional register
ranges and DT properties used by the updated SIUL2 driver.
Besides the MSCR and IMCR ranges used for pinmux and pin
configuration, the SIUL2 block also provides PGPDO and
PGPDI registers for GPIO output and input operations,
as well as an EIRQ register window for external interrupt configuration.
The driver supports both legacy pinctrl-only DTs and
extended DTs with GPIO and IRQ.
Reflect these resources in the SIUL2 pinctrl node by adding:
- the PGPDO and PGPDI register ranges
- the EIRQ register range
- gpio-controller, #gpio-cells and gpio-ranges
- interrupt-controller, #interrupt-cells and interrupts
Keep the hardware description aligned with the updated SIUL2
driver, where pinctrl, GPIO data access and the EIRQ register
block are described under the same device node.
Signed-off-by: Khristine Andreea Barbulescu <khristineandreea.barbulescu@oss.nxp.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add device tree support for the Variscite Sonata carrier board with the
DART-MX8M-PLUS system on module.
The Sonata board includes
- uSD Card support
- USB ports and OTG
- Additional Gigabit Ethernet interface
- Uart, SPI and I2C interfaces
- HDMI support
- GPIO Expanders
- RTC module
- TPM module
- CAN peripherals
Link: https://variscite.com/carrier-boards/sonata-board/
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add device tree support for the Variscite DART-MX8MP system on module.
This SOM is designed to be used with various carrier boards.
The module includes:
- NXP i.MX8M Plus MPU processor
- Up to 8GB of LPDDR4 memory
- Up to 128GB of eMMC storage memory
- Integrated 10/100/1000 Mbps Ethernet Transceiver
- Codec audio WM8904
- WIFI6 dual-band 802.11ax/ac/a/b/g/n with optional 802.15.4 and Bluetooth
Only SOM-specific peripherals are enabled by default. Carrier board
specific interfaces are left disabled to be enabled in the respective
carrier board device trees.
Link: https://variscite.com/system-on-module-som/i-mx-8/i-mx-8m-plus/dart-mx8m-plus/
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add DT compatible strings for Variscite DART-MX8MP SoM and Variscite
development carrier Board.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Move the power supply properties from the PCIe controller nodes to the
Root Port child nodes to support the new PCI pwrctrl framework.
Since i.MX95 is the new platform that under development phase, it should
be fine to simply move the power supply properties.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add the power supply properties to the Root Port child nodes to support
the new PCI pwrctrl framework.
Legacy power supply properties are retained for backward compatibility
with existing kernels. New device trees should specify power supplies at
the Root Port level to utilize the pwrctrl framework.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add the power supply properties to the Root Port child nodes to support
the new PCI pwrctrl framework.
Legacy power supply properties are retained for backward compatibility
with existing kernels. New device trees should specify power supplies at
the Root Port level to utilize the pwrctrl framework.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add the power supply properties to the Root Port child nodes to support
the new PCI pwrctrl framework.
Legacy power supply properties are retained for backward compatibility
with existing kernels. New device trees should specify power supplies at
the Root Port level to utilize the pwrctrl framework.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add the power supply property to the Root Port child node to support the
new PCI pwrctrl framework.
Legacy power supply property is retained for backward compatibility with
existing kernels. New device trees should specify power supply at the
Root Port level to utilize the pwrctrl framework.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
On the DART-MX95 platform, INL1/DMICDAT1 is used as the DMIC data line.
Add the wlf,in1l-as-dmicdat1 property to reflect this configuration.
This enables the internal MUX to switch between the ADC and DMIC as the
capture input.
Co-developed-by: Alexander Herfurtner <alexander.h@variscite.com>
Signed-off-by: Alexander Herfurtner <alexander.h@variscite.com>
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Enable the NETC and NETCMIX block control nodes on the DART-MX95 SoM.
These block control nodes are required to enable and use the NETC
Ethernet ports.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Since describing the PCIe PERST# property under Host Bridge node is now
deprecated, it is recommended to add it to the Root Port node, so creating
the root port node and add the reset-gpios property in root port.
Move the regulator to root port nodes as well, because that the PCI pwrctrl
framework had been integrated into pci-imx6 driver.
The backward compatibility is not a concern since i.MX94 is a newly
introduced platform that is still under active development.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Since describing the PCIe PERST# property under Host Bridge node is now
deprecated, it is recommended to add it to the Root Port node, so creating
the root port node and pave the path to add the reset-gpios and so on
properties in root port later.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Enable the MU2 (Message Unit 2) node on the i.MX8MP Audio Board v2.
MU2 is required for inter-processor communication between the
application CPU and the HiFi4 DSP, allowing DSP firmware to exchange
control and status messages with the Linux host.
Without this change, the DSP driver cannot establish the message
channel and DSP audio processing is non-functional.
Fixes: bf68c18150 ("arm64: dts: imx8mp-ab2: add support for NXP i.MX8MP audio board (version 2)")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add alias for lpuart5 so the UART gets a stable line number.
Without this alias, the lpuart driver fails:
fsl-lpuart 42590000.serial: failed to get alias id, errno -19
This prevents the Bluetooth controller connected to this UART from
working.
Fixes: 104a391bb6 ("arm64: dts: freescale: imx95-toradex-smarc: Enable bluetooth on lpuart5")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
The start address of the DRAM area is 0x80000000. The minimal size of the
DDR on the SoM is 1 GiB.
Fixes: 2b52fd6035 ("arm64: dts: Add support for Kontron i.MX93 OSM-S SoM and BL carrier board")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
This adds an overlay for the supported LVDS display AUO G133HAN01.
Configure the video PLL frequency to exactly match typical pixel clock of
141.200 MHz.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
This adds overlays for the supported LVDS display tianma tm070jvhg33
for both LVDS channels.
The display timings have to be specified explicitly. Using the typical
pixel clock, the LDB clock can not be configured as the 7-fold of that.
By setting pixel clock to 74.25 MHz, LDB can be configured to exactly
519.75 MHz.
Signed-off-by: Paul Gerber <paul.gerber@tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
This adds support for TQMa8MPQS module on MB-SMARC-2 board.
Signed-off-by: Paul Gerber <paul.gerber@tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
TQMa8MPxS is a SOM family using NXP i.MX8MP CPU family.
MB-SMARC-2 is an evaluation mainbord for this SOM
The SOM needs a mainboard, therefore we provide two compatibles here:
"tq,imx8mp-<SOM>" for the module and
"tq,imx8mp-<SOM>-<SBC>"
Signed-off-by: Paul Gerber <paul.gerber@tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add the GPIO pinctrl state and GPIO descriptors required for I2C1 bus
recovery on the VAR-SOM-MX8M-PLUS.
This allows the I2C controller to recover the bus if SDA or SCL are held
low by a device.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add support for the second Ethernet interface available on the Symphony
carrier board.
Enable the FEC controller, add the MaxLinear MXL86110 Gigabit Ethernet
PHY on the MDIO bus, describe its reset and power configuration, and add
the required RGMII pinctrl settings.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Enable the FlexCAN2 controller on the Symphony carrier board and add the
corresponding pinctrl configuration.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Enable PWM1 on the Symphony carrier board and add the corresponding
pinctrl configuration.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Keep the RGB_SEL line driven low on the Symphony carrier board.
This avoids leaving the line floating and ensures the board remains in
the expected display configuration.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Enable the ECSPI2 bus on the Symphony carrier board and add the pinctrl
configuration for the SPI signals and chip select GPIO.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add the FT5206 capacitive touchscreen controller on the Symphony carrier
board.
Describe the interrupt pin and touchscreen geometry.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Enable the HDMI display pipeline and HDMI audio support on the Symphony
carrier board.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add the PCIe reference clock and enable the PCIe controller and PHY on
the Symphony carrier board.
Describe the PERST# reset GPIO and configure the PHY to use an external
reference clock input.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Keep the RGB_SEL line driven low on the Symphony carrier board.
This avoids leaving the line floating and ensures the board remains in
the expected display configuration.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Mark the Symphony carrier board GPIO keys and capacitive touchscreen as
wakeup sources.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Configure HDMI DDC SCL/SDA pins to support reading EDID.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Fixes: 95d7d7d2ad ("arm64: dts: imx8mp-frdm: add sd, ethernet, wifi, usb and hdmi support")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add LVDS Display Bridge(LDB) child node to mediamix blk-ctrl node
so that video could be output through a LVDS interface.
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
i.MX93 SoC mediamix blk-ctrl contains one LDB_CTRL register and one LVDS
register which control video output through a LVDS interface. Allow the
LVDS Display Bridge(LDB) child node and add the child node to example.
i.MX93 LDB child node(bridge@20) is an addressable node, while i.MX93
Parallel Display Format Configuration(PDFC) child node(dpi-bridge) is a
non-addressable node. Mixing the addressable and non-addressable child
nodes is allowed according to discussion [1].
Link: https://lore.kernel.org/all/n6akxiayi3g6gxcqhreb4iaohmeokoalnqup6h5r2fwdt4zijt@u2wyps55ayqm/ [1]
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Enable UART1 and UART4 on the Symphony carrier board and add the
corresponding pinctrl configurations.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add the DS1337 RTC on the Symphony carrier board and disable the internal
SNVS RTC.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add the ST33KTPM2XI2C TPM device on the Symphony carrier board.
Enable the I2C4 bus, add the PCAL6408 GPIO expander used by the TPM and
describe the TPM reset line.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
