Enable the microSD slot on the VAR-SOM Symphony carrier board.
Configure USDHC2 with card-detect GPIO, pinctrl states for the supported
bus speeds and the required VMMC supply.
Update the VMMC regulator to match the latest carrier revision by moving
the enable GPIO to GPIO4_IO22 and adding the required off-on delay.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Move the USB controller configuration out of the i.MX8MM VAR-SOM dtsi
and into the VAR-SOM Symphony carrier board dts.
The SOM does not provide any USB connectors and carrier boards may
choose whether and how to route USB, therefore USB should be described
in the carrier-specific device tree instead of the SOM include.
While moving the nodes, align the Symphony USB description with the
carrier design by enabling both USB controllers, wiring USB1 to the
PTN5150 Type-C controller for dual-role operation, and updating the
PHY tuning and VBUS regulator pinctrl (including a sleep state).
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
The VAR-SOM-MX8MM currently integrates the NXP IW61x wireless module,
providing WiFi over SDIO and Bluetooth over UART.
Move the wireless module configuration out of the base
imx8mm-var-som.dtsi and provide dedicated variant includes.
The IW61x configuration is moved to imx8mm-var-som-wifi-bt-iw61x.dtsi
and used by the Symphony evaluation board device tree.
A separate imx8mm-var-som-wifi-brcm-legacy.dtsi include is added to keep
the configuration for the legacy Broadcom SDIO WiFi module used on
earlier SOM revisions.
To preserve compatibility with older SOM revisions, add a separate
imx8mm-var-som-symphony-legacy.dtb, which disables the IW61x setup and
applies the Broadcom-specific configuration.
The Broadcom-based SOM revision is no longer in production, but support
is kept for existing users.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add support for the Microchip MCP251xFD CAN-FD controller connected
to the SPI bus on the i.MX8MM VAR-SOM.
The controller uses a 40 MHz external oscillator and requires an
interrupt line and a dedicated RX interrupt GPIO.
Add the fixed clock, the MCP251xFD device node with the required
properties, and the corresponding pinctrl configuration.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
The VAR-SOM-MX8MM can integrate the WM8904, a high-performance
ultra-low-power stereo codec optimized for portable audio applications.
Add the WM8904 device to the appropriate I2C bus, enable the SAI
peripheral, and introduce the sound node to expose the sound card to the
system.
Add I3C recovery gpio properties.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Update the FEC Ethernet controller on the i.MX8MM VAR-SOM to match the
latest SOM hardware revision using the integrated MaxLinear MXL86110 PHY.
Add the PHY VDDIO supply regulator, adjust reset timings and add a
pinctrl sleep state for low-power operation.
The PHY LED signals originate on the SOM, but the actual LEDs are part
of the carrier implementation (RJ45 connector). Move the LED
configuration to the Symphony carrier device tree, matching the
evaluation board LED wiring.
Wake-on-LAN via magic packet is not supported at the VAR-SOM level and
is therefore not enabled in the SOM device tree nor in the official
evaluation carrier board configuration (symphony).
Designs requiring WoL support may enable it in their own carrier-specific
device trees if properly integrated at the hardware level.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reformat the fsl,pins tables in the i.MX8MM VAR-SOM device tree to use
consistent column alignment across all pinctrl groups.
Align the entries to match the formatting already used in the
pinctrl_fec1 group, which contains the longest pin definitions,
for improved readability and consistency.
No functional changes intended.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
The VAR-SOM-MX8MM module does not provide an onboard debug console.
UART4 is routed and exposed only on the Symphony carrier board, while
custom carrier designs may choose to expose a different UART.
Move the UART4 node from the SOM device tree to the
imx8mm-var-som-symphony.dts, keeping the SOM dtsi limited to hardware
present on the module itself.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Unlike older GIC variants, the GICv3 DT bindings do not support
specifying a CPU mask in PPI interrupt specifiers. Drop the masks.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Unlike older GIC variants, the GICv3 DT bindings do not support
specifying a CPU mask in PPI interrupt specifiers. Drop the masks.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
The PMIC provides a level-shifter for the I2C lines to the RTC. As the
level shifter needs to be enabled before the RTC can be accessed, make sure
that the PMIC driver is probed first.
As the PMIC also provides the supply voltage for the RTC through the 3.3V
regulator, simply express this in the DT to create the required dependency.
Avoid sporadic boot hangs that occurred when the RTC was accessed before
the level-shifter was enabled.
Fixes: 946ab10e3f ("arm64: dts: Add support for Kontron OSM-S i.MX8MP SoM and BL carrier board")
Signed-off-by: Annette Kobou <annette.kobou@kontron.de>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
i.MX93 contains an Arm Ethos-U65 NPU. The NPU uses the internal SRAM for
temporary buffers. The SRAM is larger than 96KB, but that is all that is
available to non-secure world.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com> # Tested on a NXP
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add support for Tianma TM070JVHG33 LVDS display on interface X11/X12 on
MBa91xxCA.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add support for CDTech S070SWV29HG-DC44 display on parallel interface X3 on
MBa91xxCA.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
This adds support for Tianma TM070JVHG33 LVDS display on interface X11/X12
on MBa91xxCA.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add support for CDTech S070SWV29HG-DC44 display on parallel interface X3 on
MBa91xxCA.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Enable Cortex M7, the vring nodes, a mailbox and reserve DDR memory for
the M7. The remoteproc framework is so capable to load and run the M7
firmware.
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Override of board compatible is unexpected, especially when the same dtso
override difference mainboard. So remove it and update the copyright year.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Override of board compatible is unexpected, especially when the same dtso
override difference mainboard. So remove it and update the copyright year.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Override of board compatible is unexpected, especially when the same dtso
override difference mainboard. So remove it and update the copyright year.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Override of board compatible is unexpected, especially when the same dtso
override difference mainboard. So remove it and update the copyright year.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Override of board compatible is unexpected, especially when the same dtso
override difference mainboard. So remove it and update the copyright year.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add device tree support for the NXP S32N79 Reference Design Board
(RDB) [1].
The S32N79-RDB enables the following peripherals:
- PL011 UART controllers (uart0, uart5, uart6, uart7)
- uSDHC controller
- IRQ steering controller
The board has 32GB of DRAM memory with 28GB usable and 4GB reserved
for ECC logic.
[1] https://www.nxp.com/products/processors-and-microcontrollers/s32-automotive-platform/s32n-vehicle-super-integration-processors:S32N
Co-developed-by: Larisa Grigore <larisa.grigore@nxp.com>
Signed-off-by: Larisa Grigore <larisa.grigore@nxp.com>
Co-developed-by: Andra-Teodora Ilie <andra.ilie@nxp.com>
Signed-off-by: Andra-Teodora Ilie <andra.ilie@nxp.com>
Signed-off-by: Ciprian Marian Costea <ciprianmarian.costea@oss.nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add device tree support for the NXP S32N79 automotive SoC [1].
The S32N79 features eight Arm Cortex-A78AE cores organized in four
dual-core clusters, with a three-level cache hierarchy (L1/L2 per core,
L3 per dual-core cluster) and 32GB of DRAM memory. It includes an SMMUv3
for IOMMU functionality.
On S32N79 SoC, peripherals are organized into subsystems, such as:
- CIS (Coherent Interconnect Subsystem)
- COSS (Connectivity Subsystem)
- FSS (Foundation Subsystem)
This initial support includes basic peripherals:
- GICv3, SMMUv3 from CIS Subsystem
- PL011 UARTs and IRQ steering controller from COSS Subsystem
- uSDHC from FSS Subsystem
Clock and Pin multiplexing settings for the chip are managed over SCMI.
[1] https://www.nxp.com/products/processors-and-microcontrollers/s32-automotive-platform/s32n-vehicle-super-integration-processors:S32N
Co-developed-by: Larisa Grigore <larisa.grigore@nxp.com>
Signed-off-by: Larisa Grigore <larisa.grigore@nxp.com>
Co-developed-by: Andra-Teodora Ilie <andra.ilie@nxp.com>
Signed-off-by: Andra-Teodora Ilie <andra.ilie@nxp.com>
Co-developed-by: Andrei Cherechesu <andrei.cherechesu@nxp.com>
Signed-off-by: Andrei Cherechesu <andrei.cherechesu@nxp.com>
Signed-off-by: Ciprian Marian Costea <ciprianmarian.costea@oss.nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Currently, in order to configure IOMUXC_SAI2_TXC__GPIO4_IO25 a magic
raw value is written in this register. This makes the code not obvious
to read and modify.
Use the MX8MP_SION symbolic macro instead of the magic value to improve
code readability.
Signed-off-by: Eduard Bostina <egbostina@gmail.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add Type-C and USB related nodes. There are two Type-C ports, one is USB2
only and another is USB3.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Currently a sensor ID is added to the reference, but
thermal-sensor@44482000 has #thermal-sensor-cells = <0>, so parsing fails.
This also has the effect that other hwmon sensors (jc42) fail to probe.
Fix this by removing the superfluous sensor ID.
Fixes: f0ed0e8444 ("arm64: dts: imx91: Add thermal-sensor and thermal-zone support")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Ethernet PHY interrupt mode is level triggered. Adjust the mode
accordingly.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Ethernet PHY interrupt mode is level triggered. Adjust the mode
accordingly.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Currently, in order to configure IOMUXC_SW_PAD_CTL_PAD a magic raw value
is written in this register. This makes code not obvious to read and
modify.
Use symbolic macros instead of the magic values to improve code
readability.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Currently MX8MP_I2C_DEFAULT macro includes a fixed drive
strength (MX8MP_DSE_X6) thus limiting its use to only I2C
pins that require X6 drive.
There are many pinctrl configurations for I2C that use different
drive strength while still using the common I2C default configurations
(pull-up, Schmitt input, pull enable, SION).
So make the MX8MP_I2C_DEFAULT macro more flexible and reusable by removing
DSE_X6 drive strength from it's definition but add or it in all places
it is necessary.
Reviewed-by: Maud Spierings <maudspierings@gocontroll.com>
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
UART1 operates in DCE mode, but the RTS/CTS pins were incorrectly
configured using the DTE pinmux setting.
Correct the pinmux to match DCE mode. Switching the RTS and CTS signals
is fine for this board, as UART1 is routed to a pin header. Existing
functionality is unaffected, as RTS/CTS could never have worked with
the incorrect pinmux.
Fixes: ddabb3ce3f ("arm64: dts: freescale: add TQMa8MPQL on MBa8MP-RAS314")
Signed-off-by: Nora Schiffer <nora.schiffer@ew.tq-group.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Support ontat,kd50g21-40nt-a1 DPI panel on i.MX93 9x9 QSB.
The panel connects with the QSB board through Adafruit DPI Display
Kippah adapter board[1].
Link: https://learn.adafruit.com/adafruit-dpi-display-kippah-ttl-tft/downloads [1]
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Remove the fallback compatible string "ethernet-phy-ieee802.3-c22" from the
Ethernet PHY node to fix below CHECK_DTB warning:
arch/arm64/boot/dts/freescale/imx8mp-beacon-kit.dtb: ethernet-phy@3 (ethernet-phy-id0022.1640): compatible: ['ethernet-phy-id0022.1640', 'ethernet-phy-ieee802.3-c22'] is too long
from schema $id: http://devicetree.org/schemas/net/micrel,gigabit.yaml
Signed-off-by: Frank Li <Frank.Li@nxp.com>
i.MX Audio Board is a configurable and functional audio processing
platform. Integrating a variety of audio input and output interfaces into
the system, the i.MX Audio Board supports HDMI input, HDMI eARC,
S/PDIF I/O, 2-ch ADC line-in, 24-ch DAC line-out and more. Based on these
features, rich audio application cases can be realized.
This is a basic device tree supporting with i.MX8M Plus SoC and Audio
board (version 2).
- Quad Cortex-A53
- 6GB LPDDR4 DRAM
- PCA9450C PMIC with regulators
- NXP PCAL6416 GPIO expanders
- RGB LEDs via GPIO expander
- I2C1, I2C2, I2C3 controllers
- UART2 (console) and UART3 (with RTS/CTS)
- USDHC3 (8-bit eMMC)
- SNVS power key (onboard power button)
- Three DAC (AK4458)
- One ADC (AK5552)
Squash Correct PAD settings (enable PUE and PU) for PMIC_nINT (GPIO1_IO3)
to avoid irq storm.
Signed-off-by: Viorel Suman <viorel.suman@nxp.com>
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Build all dtbs based on SolidRun i.MX8MP SoM with symbols (adding -@ to
dtc flags) to allow applying of device-tree overlays e.g. by the
bootloader.
The SoM has a basler camera connector that can be configured for a
particular camera by device-tree overlay. By extension all boards based
on this SoM have this connector and should support device-tree overlays.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Josua Mayer <josua@solid-run.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
imx8mp.dtsi includes a default port@1 node with an empty placeholder
endpoint intended for linking to a dsi bridge or panel.
HummingBoard Pulse mini-hdmi dtsi described a new endpoint node with a
different label attached.
This duplicate label causes confusion and is suspected to also cause
errors during dsi_attach.
Remove the duplicate node and link to the one defined in soc dtsi.
Further remove the unnecessary attach-bridge property.
Fixes: 2a222aa2be ("arm64: dts: add description for solidrun imx8mp hummingboard variants")
Signed-off-by: Josua Mayer <josua@solid-run.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Fix the polarity in vmmc regulator node for the gpio from active-high to
active-low. This is a cosmetic change as regulator default to active-low
unless property enable-active-high was also specified - ignoring the
flag on gpio handle.
Fixes: a009c0c66e ("arm64: dts: add description for solidrun imx8mp som and cubox-m")
Fixes: 2a222aa2be ("arm64: dts: add description for solidrun imx8mp hummingboard variants")
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Josua Mayer <josua@solid-run.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
IRQ mapping is already present. Add the missing DMA interrupt. This is
similar to commit 0b4c46f9ad ("arm64: dts: imx8qm-ss-hsio: Wire up
DMA IRQ for PCIe")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add device tree overlay to support the MayQueen PixPaper e-paper display
on the NXP i.MX93 FRDM board. The display is connected via LPSPI3
interface and uses GPIO pins for reset, busy and DC control.
The overlay configures:
- LPSPI3 pinmux for SPI communication (MOSI, MISO, CLK, CE0)
- PixPaper display device with proper GPIO assignments
- SPI frequency set to 1MHz for stable operation
Enable Open-EP Community pixpaper-213-c support on NXP i.MX93.
Signed-off-by: Wig Cheng <onlywig@gmail.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
The MBa8MP-RAS314 mainboard has an integrated PHY connected to the EQOS
ethernet controller which can support up to five queues. Configure
these queues in the same manor as done on the imx8mp-evk.
Setting DMA to threas mode is necessary to prevent FIFO overflows, see
commit 0bc3e333a0 ("arm64: dts: imx8mp-evk: configure multiple queues
on eqos")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
The MBa8MPxL mainboard has an integrated PHY connected to the EQOS
ethernet controller which can support up to five queues. Configure
these queues in the same manor as done on the imx8mp-evk.
Setting DMA to threas mode is necessary to prevent FIFO overflows, see
commit 0bc3e333a0 ("arm64: dts: imx8mp-evk: configure multiple queues
on eqos")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
To make the code more readable, use the macros for the GPIO and IRQ
settings.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
The SMARC evaluation carrier provides an SD card power switch that
complies with the OSM standard definition. The OSM base devicetree
already describes this correctly.
Stop overriding the vmmc-supply in the board devicetree and rely on
the definition from the OSM base DTS instead to fix the power supply
configuration for the SD card.
Fixes: 6fe1ced5cc ("arm64: dts: Add support for Kontron i.MX8MP SMARC module and eval carrier")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
The reset signal needs a pullup, but there is no hardware pullup.
As a workaround, enable the internal pullup to fix the touchscreen.
As this deviates from the default generic GPIO settings in the OSM
devicetree, add a new node for the touch pinctrl and redefine the
generic gpio1 pinctrl.
Fixes: 946ab10e3f ("arm64: dts: Add support for Kontron OSM-S i.MX8MP SoM and BL carrier board")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add overlay for Audio-Video module PEB-AV-02. Add support for panel
display, capacitive touchscreen and backlight.
The pwm-backlight uses the GPIO based PWM implementation for now. Switch
to the FlexIO PWM support once available.
Signed-off-by: Andrej Picej <andrej.picej@norik.com>
[rework commit message, use local regulator, remove compatible]
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
[m.felsch@pengutronix.de: cleanup downstream commit]
Tested-by: Primoz Fiser <primoz.fiser@norik.com>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
The Moduline Mini is a part of the wider GOcontroll Moduline ecosystem. These
are embedded controllers that focus on modularity with their swappable IO
modules.
Features:
- up to 4 Moduline IO modules
- 2 CAN busses
- 1 Ethernet
- 4 RGB leds
- 1 3D accelerometer
- optional Wi-Fi/Bluetooth
- optional 4G/GPS
Signed-off-by: Maud Spierings <maudspierings@gocontroll.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
The Moduline IV is a part of the wider GOcontroll Moduline ecosystem. These
are embedded controllers that focus on modularity with their swappable IO
modules.
Features:
- up to 8 Moduline IO modules
- 4 CAN busses
- 1 LIN bus
- 1 Ethernet
- 4 RGB leds
- optional Wi-Fi/Bluetooth
- optional 4G/GPS
Signed-off-by: Maud Spierings <maudspierings@gocontroll.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
The Ka-Ro Electronics tx8m-1610 is a COM based on the imx8mm SOC. It has
1 GB of ram and 4 GB of eMMC storage on board.
Add it to enable boards based on this module
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Maud Spierings <maudspierings@gocontroll.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
