-----BEGIN PGP SIGNATURE-----
iQJIBAABCgAyFiEEgMe7l+5h9hnxdsnuWYigwDrT+vwFAmnfwfMUHGJoZWxnYWFz
QGdvb2dsZS5jb20ACgkQWYigwDrT+vxwIRAAlN1h5er8aFDbjON5YMXBZqlQmzaC
bjlUHgwm7HkdErTFozyuqhE8QUO1kCm4uMQzeyJdfY9nRWqMDOuKYxMD5j0exk+o
4tbbJg6Xx4dq7Qrawy9PhxyQm/PDAcvs+FRRlGala+qq9o3fxPDOAZVDE/1C8qFQ
Jd7GGd7NZn/NN4xrqST4RQHjO8fwaMwmksWCStsb79kfesQWP6kLADGfIMcWxNUB
2s+oTnK6Hw0tkBv56n6i8mbb0EzS3/RN1daTevGAta1rmfUVVtWGRZ4paMvv0Owi
Rl5+O5Jz6/c1qiXZbUqu5CRQPIy7Dr3JPvURcZX6qbsV8PzWXZr0Wi+geWefGOnp
55y+3OT0vdBGAuXLJhrcU7Clzq9D/TZOt8oTI8IFArUfDlmrAIdozPn7gr+VGre5
QuKymSk3XWtyIbe4o8UeZ4f9g0y6ZY1XvtvB7K1tze+OOmqlkfq966+z8aZuGOKx
ZvAU/NIat5H02EgB4dEVOP8R5vPZlXGT0RLGl1JWRypPWyZDbVVA3z927qRQG5md
IsVq8WaIrB1zyl9g37lZeEaYwP/qCIQsHkMGPYcP4wdOQEV9AQqi5pmjMXnWyQJD
PR1nvmTKW7USRCJ+pz8xPhZh0cj3ENaddORTD3I/0CGVV0y452bU/5rr4T+K04bK
PCJBpxTIDuWDwXc=
=FFRz
-----END PGP SIGNATURE-----
Merge tag 'pci-v7.1-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Allow TLP Processing Hints to be enabled for RCiEPs (George Abraham
P)
- Enable AtomicOps only if we know the Root Port supports them (Gerd
Bayer)
- Don't enable AtomicOps for RCiEPs since none of them need Atomic
Ops and we can't tell whether the Root Complex would support them
(Gerd Bayer)
- Leave Precision Time Measurement disabled until a driver enables it
to avoid PCIe errors (Mika Westerberg)
- Make pci_set_vga_state() fail if bridge doesn't support VGA
routing, i.e., PCI_BRIDGE_CTL_VGA is not writable, and return
errors to vga_get() callers including userspace via
/dev/vga_arbiter (Simon Richter)
- Validate max-link-speed from DT in j721e, brcmstb, mediatek-gen3,
rzg3s drivers (where the actual controller constraints are known),
and remove validation from the generic OF DT accessor (Hans Zhang)
- Remove pc110pad driver (no longer useful after 486 CPU support
removed) and no_pci_devices() (pc110pad was the last user) (Dmitry
Torokhov, Heiner Kallweit)
Resource management:
- Prevent assigning space to unimplemented bridge windows; previously
we mistakenly assumed prefetchable window existed and assigned
space and put a BAR there (Ahmed Naseef)
- Avoid shrinking bridge windows to fit in the initial Root Port
window; fixes one problem with devices with large BARs connected
via switches, e.g., Thunderbolt (Ilpo Järvinen)
- Pass full extent of empty space, not just the aligned space, to
resource_alignf callback so free space before the requested
alignment can be used (Ilpo Järvinen)
- Place small resources before larger ones for better utilization of
address space (Ilpo Järvinen)
- Fix alignment calculation for resource size larger than align,
e.g., bridge windows larger than the 1MB required alignment (Ilpo
Järvinen)
Reset:
- Update slot handling so all ARI functions are treated as being in
the same slot. They're all reset by Secondary Bus Reset, but
previously drivers of ARI functions that appeared to be on a
non-zero device weren't notified and fatal hardware errors could
result (Keith Busch)
- Make sysfs reset_subordinate hotplug safe to avoid spurious hotplug
events (Keith Busch)
- Hide Secondary Bus Reset ('bus') from sysfs reset_methods if masked
by CXL because it has no effect (Vidya Sagar)
- Avoid FLR for AMD NPU device, where it causes the device to hang
(Lizhi Hou)
Error handling:
- Clear only error bits in PCIe Device Status to avoid accidentally
clearing Emergency Power Reduction Detected (Shuai Xue)
- Check for AER errors even in devices without drivers (Lukas Wunner)
- Initialize ratelimit info so DPC and EDR paths log AER error
information (Kuppuswamy Sathyanarayanan)
Power control:
- Add UPD720201/UPD720202 USB 3.0 xHCI Host Controller .compatible so
generic pwrctrl driver can control it (Neil Armstrong)
Hotplug:
- Set LED_HW_PLUGGABLE for NPEM hotplug-capable ports so LED core
doesn't complain when setting brightness fails because the endpoint
is gone (Richard Cheng)
Peer-to-peer DMA:
- Allow wildcards in list of host bridges that support peer-to-peer
DMA between hierarchy domains and add all Google SoCs (Jacob
Moroni)
Endpoint framework:
- Advertise dynamic inbound mapping support in pci-epf-test and
update host pci_endpoint_test to skip doorbell testing if not
advertised by endpoint (Koichiro Den)
- Return 0, not remaining timeout, when MHI eDMA ops complete so
mhi_ep_ring_add_element() doesn't interpret non-zero as failure
(Daniel Hodges)
- Remove vntb and ntb duplicate resource teardown that leads to oops
when .allow_link() fails or .drop_link() is called (Koichiro Den)
- Disable vntb delayed work before clearing BAR mappings and
doorbells to avoid oops caused by doing the work after resources
have been torn down (Koichiro Den)
- Add a way to describe reserved subregions within BARs, e.g.,
platform-owned fixed register windows, and use it for the RK3588
BAR4 DMA ctrl window (Koichiro Den)
- Add BAR_DISABLED for BARs that will never be available to an EPF
driver, and change some BAR_RESERVED annotations to BAR_DISABLED
(Niklas Cassel)
- Add NTB .get_dma_dev() callback for cases where DMA API requires a
different device, e.g., vNTB devices (Koichiro Den)
- Add reserved region types for MSI-X Table and PBA so Endpoint
controllers can them as describe hardware-owned regions in a
BAR_RESERVED BAR (Manikanta Maddireddy)
- Make Tegra194/234 BAR0 programmable and remove 1MB size limit
(Manikanta Maddireddy)
- Expose Tegra BAR2 (MSI-X) and BAR4 (DMA) as 64-bit BAR_RESERVED
(Manikanta Maddireddy)
- Add Tegra194 and Tegra234 device table entries to pci_endpoint_test
(Manikanta Maddireddy)
- Skip the BAR subrange selftest if there are not enough inbound
window resources to run the test (Christian Bruel)
New native PCIe controller drivers:
- Add DT binding and driver for Andes QiLai SoC PCIe host controller
(Randolph Lin)
- Add DT binding and driver for ESWIN PCIe Root Complex (Senchuan
Zhang)
Baikal T-1 PCIe controller driver:
- Remove driver since it never quite became usable (Andy Shevchenko)
Cadence PCIe controller driver:
- Implement byte/word config reads with dword (32-bit) reads because
some Cadence controllers don't support sub-dword accesses (Aksh
Garg)
CIX Sky1 PCIe controller driver:
- Add 'power-domains' to DT binding for SCMI power domain (Gary Yang)
Freescale i.MX6 PCIe controller driver:
- Add i.MX94 and i.MX943 to fsl,imx6q-pcie-ep DT binding (Richard
Zhu)
- Delay instead of polling for L2/L3 Ready after PME_Turn_off when
suspending i.MX6SX because LTSSM registers are inaccessible
(Richard Zhu)
- Separate PERST# assertion (for resetting endpoints) from core reset
(for resetting the RC itself) to prepare for new DTs with PERST#
GPIO in per-Root Port nodes (Sherry Sun)
- Retain Root Port MSI capability on i.MX7D, i.MX8MM, and i.MX8MQ so
MSI from downstream devices will work (Richard Zhu)
- Fix i.MX95 reference clock source selection when internal refclk is
used (Franz Schnyder)
Freescale Layerscape PCIe controller driver:
- Allow building as a removable module (Sascha Hauer)
MediaTek PCIe Gen3 controller driver:
- Use dev_err_probe() to simplify error paths and make deferred probe
messages visible in /sys/kernel/debug/devices_deferred (Chen-Yu
Tsai)
- Power off device if setup fails (Chen-Yu Tsai)
- Integrate new pwrctrl API to enable power control for WiFi/BT
adapters on mainboard or in PCIe or M.2 slots (Chen-Yu Tsai)
NVIDIA Tegra194 PCIe controller driver:
- Poll less aggressively and non-atomically for PME_TO_Ack during
transition to L2 (Vidya Sagar)
- Disable LTSSM after transition to Detect on surprise link down to
stop toggling between Polling and Detect (Manikanta Maddireddy)
- Don't force the device into the D0 state before L2 when suspending
or shutting down the controller (Vidya Sagar)
- Disable PERST# IRQ only in Endpoint mode because it's not
registered in Root Port mode (Manikanta Maddireddy)
- Handle 'nvidia,refclk-select' as optional (Vidya Sagar)
- Disable direct speed change in Endpoint mode so link speed change
is controlled by the host (Vidya Sagar)
- Set LTR values before link up to avoid bogus LTR messages with 0
latency (Vidya Sagar)
- Allow system suspend when the Endpoint link is down (Vidya Sagar)
- Use DWC IP core version, not Tegra custom values, to avoid DWC core
version check warnings (Manikanta Maddireddy)
- Apply ECRC workaround to devices based on DesignWare 5.00a as well
as 4.90a (Manikanta Maddireddy)
- Disable PM Substate L1.2 in Endpoint mode to work around Tegra234
erratum (Vidya Sagar)
- Delay post-PERST# cleanup until core is powered on to avoid CBB
timeout (Manikanta Maddireddy)
- Assert CLKREQ# so switches that forward it to their downstream side
can bring up those links successfully (Vidya Sagar)
- Calibrate pipe to UPHY for Endpoint mode to reset stale PLL state
from any previous bad link state (Vidya Sagar)
- Remove IRQF_ONESHOT flag from Endpoint interrupt registration so
DMA driver and Endpoint controller driver can share the interrupt
line (Vidya Sagar)
- Enable DMA interrupt to support DMA in both Root Port and Endpoint
modes (Vidya Sagar)
- Enable hardware link retraining after link goes down in Endpoint
mode (Vidya Sagar)
- Add DT binding and driver support for core clock monitoring (Vidya
Sagar)
Qualcomm PCIe controller driver:
- Advertise 'Hot-Plug Capable' and set 'No Command Completed Support'
since Qcom Root Ports support hotplug events like DL_Up/Down and
can accept writes to Slot Control without delays between writes
(Krishna Chaitanya Chundru)
Renesas R-Car PCIe controller driver:
- Mark Endpoint BAR0 and BAR2 as Resizable (Koichiro Den)
- Reduce EPC BAR alignment requirement to 4K (Koichiro Den)
Renesas RZ/G3S PCIe controller driver:
- Add RZ/G3E to DT binding and to driver (John Madieu)
- Assert (not deassert) resets in probe error path (John Madieu)
- Assert resets in suspend path in reverse order they were deasserted
during probe (John Madieu)
- Rework inbound window algorithm to prevent mapping more than
intended region and enforce alignment on size, to prepare for
RZ/G3E support (John Madieu)
Rockchip DesignWare PCIe controller driver:
- Add tracepoints for PCIe controller LTSSM transitions and link rate
changes (Shawn Lin)
- Trace LTSSM events collected by the dw-rockchip debug FIFO (Shawn
Lin)
SOPHGO PCIe controller driver:
- Disable ASPM L0s and L1 on Sophgo 2042 PCIe Root Ports that
advertise support for them (Yao Zi)
Synopsys DesignWare PCIe controller driver:
- Continue with system suspend even if an Endpoint doesn't respond
with PME_TO_Ack message (Manivannan Sadhasivam)
- Set Endpoint MSI-X Table Size in the correct function of a
multi-function device when configuring MSI-X, not in Function 0
(Aksh Garg)
- Set Max Link Width and Max Link Speed for all functions of a
multi-function device, not just Function 0 (Aksh Garg)
- Expose PCIe event counters in groups 5-7 in debugfs (Hans Zhang)
Miscellaneous:
- Warn only once about invalid ACS kernel parameter format (Richard
Cheng)
- Suppress FW_BUG warning when writing sysfs 'numa_node' with the
current value (Li RongQing)
- Drop redundant 'depends on PCI' from Kconfig (Julian Braha)"
* tag 'pci-v7.1-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (165 commits)
PCI/P2PDMA: Add Google SoCs to the P2P DMA host bridge list
PCI/P2PDMA: Allow wildcard Device IDs in host bridge list
PCI: sg2042: Avoid L0s and L1 on Sophgo 2042 PCIe Root Ports
PCI: cadence: Add flags for disabling ASPM capability for broken Root Ports
PCI: tegra194: Add core monitor clock support
dt-bindings: PCI: tegra194: Add monitor clock support
PCI: tegra194: Enable hardware hot reset mode in Endpoint mode
PCI: tegra194: Enable DMA interrupt
PCI: tegra194: Remove IRQF_ONESHOT flag during Endpoint interrupt registration
PCI: tegra194: Calibrate pipe to UPHY for Endpoint mode
PCI: tegra194: Assert CLKREQ# explicitly by default
PCI: tegra194: Fix CBB timeout caused by DBI access before core power-on
PCI: tegra194: Disable L1.2 capability of Tegra234 EP
PCI: dwc: Apply ECRC workaround to DesignWare 5.00a as well
PCI: tegra194: Use DWC IP core version
PCI: tegra194: Free up Endpoint resources during remove()
PCI: tegra194: Allow system suspend when the Endpoint link is not up
PCI: tegra194: Set LTR message request before PCIe link up in Endpoint mode
PCI: tegra194: Disable direct speed change for Endpoint mode
PCI: tegra194: Use devm_gpiod_get_optional() to parse "nvidia,refclk-select"
...
- Poll less aggressively and non-atomically for PME_TO_Ack during
transition to L2 (Vidya Sagar)
- Increase LTSSM poll time on surprise link down (Manikanta Maddireddy)
- Disable LTSSM after transition to Detect on surprise link down to stop
toggling between Polling and Detect (Manikanta Maddireddy)
- Don't force the device into the D0 state before L2 when suspending or
shutting down the controller (Vidya Sagar)
- Disable PERST# IRQ only in Endpoint mode because it's not registered in
Root Port mode (Manikanta Maddireddy)
- Handle 'nvidia,refclk-select' as optional (Vidya Sagar)
- Disable direct speed change in Endpoint mode so link speed change is
controlled by the host (Vidya Sagar)
- Set LTR values before link up to avoid bogus LTR messages with 0 latency
(Vidya Sagar)
- Allow system suspend when the Endpoint link is down (Vidya Sagar)
- During remove, free resources allocated during Endpoint .probe() (Vidya
Sagar)
- Use DWC IP core version, not Tegra custom values, to avoid DWC core
version check warnings (Manikanta Maddireddy)
- Apply ECRC workaround to devices based on DesignWare 5.00a as well
as 4.90a (Manikanta Maddireddy)
- Disable PM Substate L1.2 in Endpoint mode to work around Tegra234 erratum
(Vidya Sagar)
- Delay post-PERST# cleanup until core is powered on to avoid CBB timeout
(Manikanta Maddireddy)
- Assert CLKREQ# so switches that forward it to their downstream side can
bring up those links successfully (Vidya Sagar)
- Calibrate pipe to UPHY for Endpoint mode to reset stale PLL state from
any previous bad link state (Vidya Sagar)
- Remove IRQF_ONESHOT flag from Endpoint interrupt registration so DMA
driver and Endpoint controller driver can share the interrupt line (Vidya
Sagar)
- Enable DMA interrupt to support DMA in both Root Port and Endpoint modes
(Vidya Sagar)
- Enable hardware link retraining after link goes down in Endpoint mode
(Vidya Sagar)
- Add DT binding and driver support for core clock monitoring (Vidya Sagar)
* pci/controller/dwc-tegra194:
PCI: tegra194: Add core monitor clock support
dt-bindings: PCI: tegra194: Add monitor clock support
PCI: tegra194: Enable hardware hot reset mode in Endpoint mode
PCI: tegra194: Enable DMA interrupt
PCI: tegra194: Remove IRQF_ONESHOT flag during Endpoint interrupt registration
PCI: tegra194: Calibrate pipe to UPHY for Endpoint mode
PCI: tegra194: Assert CLKREQ# explicitly by default
PCI: tegra194: Fix CBB timeout caused by DBI access before core power-on
PCI: tegra194: Disable L1.2 capability of Tegra234 EP
PCI: dwc: Apply ECRC workaround to DesignWare 5.00a as well
PCI: tegra194: Use DWC IP core version
PCI: tegra194: Free up Endpoint resources during remove()
PCI: tegra194: Allow system suspend when the Endpoint link is not up
PCI: tegra194: Set LTR message request before PCIe link up in Endpoint mode
PCI: tegra194: Disable direct speed change for Endpoint mode
PCI: tegra194: Use devm_gpiod_get_optional() to parse "nvidia,refclk-select"
PCI: tegra194: Disable PERST# IRQ only in Endpoint mode
PCI: tegra194: Don't force the device into the D0 state before L2
PCI: tegra194: Disable LTSSM after transition to Detect on surprise link down
PCI: tegra194: Increase LTSSM poll time on surprise link down
PCI: tegra194: Fix polling delay for L2 state
- Mark BAR0 and BAR2 as Resizable (Koichiro Den)
- Reduce EPC BAR alignment requirement to 4K (Koichiro Den)
* pci/controller/dwc-rcar-gen4-ep:
PCI: dwc: rcar-gen4: Change EPC BAR alignment to 4K as per the documentation
PCI: dwc: rcar-gen4: Mark BAR0 and BAR2 as Resizable BARs in endpoint mode
# Conflicts:
# drivers/pci/controller/dwc/pcie-rcar-gen4.c
- Advertise 'Hot-Plug Capable' and set 'No Command Completed Support' since
Qcom Root Ports support hotplug events like DL_Up/Down and can accept
writes to Slot Control without delays between writes (Krishna Chaitanya
Chundru)
* pci/controller/dwc-qcom:
PCI: qcom: Advertise Hotplug Slot Capability with no Command Completion support
- Allow Layerscape host controller driver to be build as a removable module
(Sascha Hauer)
* pci/controller/dwc-layerscape:
PCI: layerscape: Allow to compile as module
- Fix device node reference leak in imx_pcie_probe() (Felix Gu)
- Delay instead of polling for L2/L3 Ready after PME_Turn_off when
suspending i.MX6SX because LTSSM registers are inaccessible (Richard Zhu)
- Separate PERST# assertion (for resetting endpoints) from core reset (for
resetting the RC itself) to prepare for new DTs with PERST# GPIO in
per-Root Port nodes (Sherry Sun)
- Retain the Root Port MSI capability on i.MX7D, i.MX8MM, and i.MX8MQ so
MSI from downstream devices will work (Richard Zhu)
- Fix the i.MX95 reference clock source selection when internal refclk is
used (Franz Schnyder)
* pci/controller/dwc-imx6:
PCI: imx6: Fix reference clock source selection for i.MX95
PCI: imx6: Keep Root Port MSI capability with iMSI-RX to work around hardware bug
PCI: imx6: Separate PERST# assertion from core reset functions
PCI: imx6: Change imx_pcie_deassert_core_reset() return type to void
PCI: imx6: Skip waiting for L2/L3 Ready on i.MX6SX
PCI: imx6: Fix device node reference leak in imx_pcie_probe()
- Correct the IRQ number logged in INTx error message (Rakuram Eswaran)
* pci/controller/dwc-amd-mdb:
PCI: amd-mdb: Correct IRQ number in INTx error message
- Continue with system suspend even if an Endpoint doesn't respond with
PME_TO_Ack message (Manivannan Sadhasivam)
- Remove the Baikal-T1 controller driver since it never quite became usable
(Andy Shevchenko)
- Set Endpoint MSI-X Table Size in the correct function of a multi-function
device when configuring MSI-X, not in Function 0 (Aksh Garg)
- Set Max Link Width and Max Link Speed for all functions of a
multi-function device, not just Function 0 (Aksh Garg)
- Clean up in the dw_pcie_resume_noirq() error path (Manivannan Sadhasivam)
- Expose PCIe event counters in groups 5-7 in debugfs (Hans Zhang)
- Fix type mismatch for kstrtou32_from_user() in debugfs write functions
(Hans Zhang)
* pci/controller/dwc:
PCI: dwc: Fix type mismatch for kstrtou32_from_user() return value
PCI: dwc: Expose PCIe event counters for groups 5 to 7 over debugfs
PCI: dwc: Perform cleanup in the error path of dw_pcie_resume_noirq()
PCI: dwc: ep: Mirror the max link width and speed fields to all functions
PCI: dwc: ep: Fix MSI-X Table Size configuration in dw_pcie_ep_set_msix()
PCI: dwc: Remove not-going-to-be-supported code for Baikal SoC
PCI: dwc: Proceed with system suspend even if the endpoint doesn't respond with PME_TO_Ack message
- Add pcie_get_link_speed() to encapsulate and bounds-check
pcie_link_speed[] accesses (Hans Zhang)
- Validate max-link-speed from DT in j721e, brcmstb, mediatek-gen3, rzg3s
(where the actual controller constraints are known), and remove it from
the generic OF DT accessor (Hans Zhang)
* pci/controller/max-link-speed:
PCI: of: Remove max-link-speed generation validation
PCI: controller: Validate max-link-speed
PCI: j721e: Validate max-link-speed from DT
PCI: dwc: Use pcie_get_link_speed() helper for safe array access
PCI: Add pcie_get_link_speed() helper for safe array access
- Free all previously requested IRQs in epf_ntb_db_bar_init_msi_doorbell()
error path (Koichiro Den)
- Free doorbell IRQ in pci-epf-test only if it has actually been requested
(Koichiro Den)
- Discard pointer to doorbell message array after freeing it in
pci_epf_alloc_doorbell() error path (Koichiro Den)
- Advertise dynamic inbound mapping support in pci-epf-test and update host
pci_endpoint_test to skip doorbell testing if not advertised by endpoint
(Koichiro Den)
- Constify configfs item and group operations (Christophe JAILLET)
- Use array_index_nospec() on configfs MW show/store attributes (Koichiro
Den)
- Return -ERANGE (not -EINVAL) for configfs out-of-range MW index (Koichiro
Den)
- Return 0, not remaining timeout, when MHI eDMA ops complete so
mhi_ep_ring_add_element() doesn't interpret non-zero as failure (Daniel
Hodges)
- Remove vntb and ntb duplicate resource teardown that leads to oops when
.allow_link() fails or .drop_link() is called (Koichiro Den)
- Disable vntb delayed work before clearing BAR mappings and doorbells to
avoid oops caused by doing the work after resources have been torn down
(Koichiro Den)
- Fix pci_epf_add_vepf() kernel-doc typo (Alok Tiwari)
- Propagate pci_epf_create() errors to pci_epf_make() callers (Alok Tiwari)
- Remove redundant BAR_RESERVED annotation for the high order part of a
64-bit BAR (Niklas Cassel)
- Add a way to describe reserved subregions within BARs, e.g.,
platform-owned fixed register windows, and use it for the RK3588 BAR4 DMA
ctrl window (Koichiro Den)
- Add BAR_DISABLED for BARs that will never be available to an EPF driver,
and change some BAR_RESERVED annotations to BAR_DISABLED (Niklas Cassel)
- Disable BARs in common code instead of in each glue driver (Niklas
Cassel)
- Advertise reserved BARs in Capabilities so host-side drivers can skip
them (Niklas Cassel)
- Skip reserved BARs in selftests (Niklas Cassel)
- Improve error messages and include device name when available (Manivannan
Sadhasivam)
- Add NTB .get_dma_dev() callback for cases where DMA API requires a
different device, e.g., vNTB devices (Koichiro Den)
- Return -EINVAL, not -ENOSPC, if endpoint test determines the subrange
size is too small (Koichiro Den)
- Add reserved region types for MSI-X Table and PBA so Endpoint controllers
can them as describe hardware-owned regions in a BAR_RESERVED BAR
(Manikanta Maddireddy)
- Make Tegra194/234 BAR0 programmable and remove 1MB size limit (Manikanta
Maddireddy)
- Expose Tegra BAR2 (MSI-X) and BAR4 (DMA) as 64-bit BAR_RESERVED
(Manikanta Maddireddy)
- Add Tegra194 and Tegra234 device table entries to pci_endpoint_test
(Manikanta Maddireddy)
- Skip the BAR subrange selftest if there are not enough inbound window
resources to run the test (Christian Bruel)
* pci/endpoint:
selftests: pci_endpoint: Skip BAR subrange test on -ENOSPC
misc: pci_endpoint_test: Add Tegra194 and Tegra234 device table entries
PCI: tegra194: Expose BAR2 (MSI-X) and BAR4 (DMA) as 64-bit BAR_RESERVED
PCI: tegra194: Make BAR0 programmable and remove 1MB size limit
PCI: endpoint: Add reserved region type for MSI-X Table and PBA
misc: pci_endpoint_test: Use -EINVAL for small subrange size
PCI: endpoint: pci-epf-vntb: Implement .get_dma_dev()
NTB: ntb_transport: Use ntb_get_dma_dev() for DMA buffers
NTB: core: Add .get_dma_dev() callback to ntb_dev_ops
PCI: endpoint: Improve error messages
PCI: endpoint: Print the EPF name in the error log of pci_epf_make()
selftests: pci_endpoint: Skip reserved BARs
misc: pci_endpoint_test: Give reserved BARs a distinct error code
PCI: endpoint: pci-epf-test: Advertise reserved BARs
PCI: dwc: Disable BARs in common code instead of in each glue driver
PCI: dwc: Replace certain BAR_RESERVED with BAR_DISABLED in glue drivers
PCI: endpoint: Introduce pci_epc_bar_type BAR_DISABLED
PCI: dw-rockchip: Describe RK3588 BAR4 DMA ctrl window
PCI: endpoint: Describe reserved subregions within BARs
PCI: endpoint: Allow only_64bit on BAR_RESERVED
PCI: endpoint: Do not mark the BAR succeeding a 64-bit BAR as BAR_RESERVED
PCI: endpoint: Propagate error from pci_epf_create()
PCI: endpoint: Fix typo in pci_epf_add_vepf() kernel-doc
PCI: endpoint: pci-epf-vntb: Stop cmd_handler work in epf_ntb_epc_cleanup
PCI: endpoint: pci-epf-ntb: Remove duplicate resource teardown
PCI: endpoint: pci-epf-vntb: Remove duplicate resource teardown
PCI: epf-mhi: Return 0, not remaining timeout, when eDMA ops complete
PCI: endpoint: pci-epf-vntb: Return -ERANGE for out-of-range MW index
PCI: endpoint: pci-epf-vntb: Use array_index_nospec() on mws_size[] access
PCI: endpoint: Constify struct configfs_item_operations and configfs_group_operations
selftests: pci_endpoint: Skip doorbell test when unsupported
misc: pci_endpoint_test: Gate doorbell test on dynamic inbound mapping
PCI: endpoint: pci-epf-test: Advertise dynamic inbound mapping support
PCI: endpoint: pci-ep-msi: Fix error unwind and prevent double alloc
PCI: endpoint: pci-epf-test: Don't free doorbell IRQ unless requested
PCI: endpoint: pci-epf-vntb: Fix MSI doorbell IRQ unwind
Add support for Tegra PCIe core clock monitoring. Monitoring tracks rate
changes that may occur due to link speed changes and is useful for
detecting core clock changes not initiated by software. Parse the monitor
clock from device tree and enable it when present.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://patch.msgid.link/20260324191000.1095768-8-mmaddireddy@nvidia.com
When PCIe link goes down, hardware can retrain the link and try to link up.
To enable this feature, program the APPL_CTRL register with hardware hot
reset with immediate LTSSM enable mode when the controller is operating in
endpoint mode.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
[mani: commit log]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
Link: https://patch.msgid.link/20260324191000.1095768-6-mmaddireddy@nvidia.com
The Tegra PCIe Endpoint controller has a single interrupt line that is
shared between multiple interrupt sources:
1. PCIe link state events (link up, hot reset done)
2. Configuration space events (Bus Master Enable changes)
3. DMA completion events
The interrupt is currently registered with IRQF_ONESHOT, which keeps the
interrupt line masked until the threaded handler completes. That blocks
processing of DMA completion events (and other sources) while the
threaded handler runs.
Removing IRQF_ONESHOT is safe for the following reasons:
1. The hard IRQ handler (tegra_pcie_ep_hard_irq) properly acknowledges and
clears all interrupt status bits in hardware before returning. This
prevents interrupt storms and ensures the interrupt controller can
re-enable the interrupt line immediately.
2. The follow-up commit adds handling in the hard IRQ for DMA completion
events. Dropping IRQF_ONESHOT is required so the line is unmasked
after the hard IRQ returns and those events can be serviced without
being blocked by the threaded handler.
3. The threaded handler (tegra_pcie_ep_irq_thread) only processes link-up
notifications and LTR message sending. These operations don't conflict
with DMA interrupt processing and don't require the interrupt line to
remain masked.
This change enables both DMA driver and Endpoint controller driver to share
the interrupt line without blocking each other.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
Link: https://patch.msgid.link/20260324191000.1095768-4-mmaddireddy@nvidia.com
Calibrate 'Pipe to Universal PHY(UPHY)' (P2U) for the Endpoint controller
to request UPHY PLL rate change to 2.5GT/s (Gen 1) during initialization.
This helps to reset stale PLL state from the previous bad link state.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
Link: https://patch.msgid.link/20260324191000.1095768-3-mmaddireddy@nvidia.com
The Root Port's CLKREQ# signal is shared with a downstream PCIe switch and
the endpoints behind it. By default, APPL_PINMUX_CLKREQ_OVERRIDE only
overrides the CLKREQ# input to the controller (so REFCLK is enabled
internally); it does not drive the CLKREQ# output pin low. Some PCIe
switches (e.g. Broadcom PCIe Gen4) forward the Root Port's CLKREQ# to their
downstream side and expect it to be driven low for REFCLK, even when the
switch does not support CLK-PM or ASPM-L1SS. Without driving the output
pin low, link-up can fail between the switch and endpoints.
Clear APPL_PINMUX_CLKREQ_DEFAULT_VALUE so the CLKREQ# output pad is
explicitly driven low. That makes the shared CLKREQ# line low on the wire
and avoids link-up issues with such switches.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://patch.msgid.link/20260324191000.1095768-2-mmaddireddy@nvidia.com
When PERST# is deasserted twice (assert -> deassert -> assert -> deassert),
a CBB (Control Backbone) timeout occurs at DBI register offset 0x8bc
(PCIE_MISC_CONTROL_1_OFF). This happens because pci_epc_deinit_notify()
and dw_pcie_ep_cleanup() are called before reset_control_deassert() powers
on the controller core.
The call chain that causes the timeout:
pex_ep_event_pex_rst_deassert()
pci_epc_deinit_notify()
pci_epf_test_epc_deinit()
pci_epf_test_clear_bar()
pci_epc_clear_bar()
dw_pcie_ep_clear_bar()
__dw_pcie_ep_reset_bar()
dw_pcie_dbi_ro_wr_en() <- Accesses 0x8bc DBI register
reset_control_deassert(pcie->core_rst) <- Core powered on HERE
The DBI registers, including PCIE_MISC_CONTROL_1_OFF (0x8bc), are only
accessible after the controller core is powered on via
reset_control_deassert(pcie->core_rst). Accessing them before this point
results in a CBB timeout because the hardware is not yet operational.
Fix this by moving pci_epc_deinit_notify() and dw_pcie_ep_cleanup() to
after reset_control_deassert(pcie->core_rst), ensuring the controller is
fully powered on before any DBI register accesses occur.
Fixes: 40e2125381 ("PCI: tegra194: Move controller cleanups to pex_ep_event_pex_rst_deassert()")
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
Link: https://patch.msgid.link/20260324190755.1094879-15-mmaddireddy@nvidia.com
When Tegra234 is operating in the Endpoint mode with L1.2 enabled, PCIe
link goes down during L1.2 exit. This is because Tegra234 powers up UPHY
PLL immediately without making sure that the REFCLK is stable.
This causes UPHY PLL to fail to lock to the correct frequency and leads to
link going down. There is no hardware fix for this, hence do not advertise
the L1.2 capability in the Endpoint mode.
Fixes: a54e190737 ("PCI: tegra194: Add Tegra234 PCIe support")
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
Link: https://patch.msgid.link/20260324190755.1094879-14-mmaddireddy@nvidia.com
The ECRC (TLP digest) workaround was originally added for DesignWare
version 4.90a. Tegra234 SoC has 5.00a DWC HW version, which has the same
ATU TD override behaviour, so apply the workaround for 5.00a too.
Fixes: a54e190737 ("PCI: tegra194: Add Tegra234 PCIe support")
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
Link: https://patch.msgid.link/20260324190755.1094879-13-mmaddireddy@nvidia.com
Tegra194 PCIe driver used custom version numbers to detect Tegra194 and
Tegra234 IPs. With version detect logic added, version check results in
mismatch warnings:
tegra194-pcie 14100000.pcie: Versions don't match (0000562a != 3536322a)
Use HW version numbers which match to PORT_LOGIC.PCIE_VERSION_OFF in
Tegra194 driver to avoid these kernel warnings.
Fixes: a54e190737 ("PCI: tegra194: Add Tegra234 PCIe support")
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
Link: https://patch.msgid.link/20260324190755.1094879-12-mmaddireddy@nvidia.com
Free up the resources during remove() that were acquired by the DesignWare
driver for the Endpoint mode during probe().
Fixes: bb617cbd81 ("PCI: tegra194: Clean up the exit path for Endpoint mode")
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
Link: https://patch.msgid.link/20260324190755.1094879-11-mmaddireddy@nvidia.com
Host software initiates the L2 sequence. PCIe link is kept in L2 state
during suspend. If Endpoint mode is enabled and the link is up, the
software cannot proceed with suspend. However, when the PCIe Endpoint
driver is probed, but the PCIe link is not up, Tegra can go into suspend
state. So, allow system to suspend in this case.
Fixes: de2bbf2b71 ("PCI: tegra194: Don't allow suspend when Tegra PCIe is in EP mode")
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
Link: https://patch.msgid.link/20260324190755.1094879-10-mmaddireddy@nvidia.com
LTR message should be sent as soon as the Root Port enables LTR in the
Endpoint mode. So set snoop and no-snoop LTR timing and LTR message request
before the PCIe link comes up, so that the LTR message is sent upstream as
soon as LTR is enabled.
Without programming these values, the Endpoint would send latencies of 0 to
the host, which will be inaccurate.
Fixes: c57247f940 ("PCI: tegra: Add support for PCIe endpoint mode in Tegra194")
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
[mani: commit log]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://patch.msgid.link/20260324190755.1094879-9-mmaddireddy@nvidia.com
Pre-silicon simulation showed the controller operating in Endpoint mode
initiating link speed change after completing Secondary Bus Reset. Ideally,
the Root Port or the Switch Downstream Port should initiate the link speed
change post SBR, not the Endpoint.
So, as per the hardware team recommendation, disable direct speed change
for the Endpoint mode to prevent it from initiating speed change after the
physical layer link is up at Gen1, leaving speed change ownership with the
host.
Fixes: c57247f940 ("PCI: tegra: Add support for PCIe endpoint mode in Tegra194")
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
[mani: commit log]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
Link: https://patch.msgid.link/20260324190755.1094879-8-mmaddireddy@nvidia.com
The GPIO DT property "nvidia,refclk-select", to select the PCIe reference
clock is optional. Use devm_gpiod_get_optional() to get it.
Fixes: c57247f940 ("PCI: tegra: Add support for PCIe endpoint mode in Tegra194")
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
Link: https://patch.msgid.link/20260324190755.1094879-7-mmaddireddy@nvidia.com
The PERST# GPIO interrupt is only registered when the controller is
operating in Endpoint mode. In Root Port mode, the PERST# GPIO is
configured as an output to control downstream devices, and no interrupt is
registered for it.
Currently, tegra_pcie_dw_stop_link() unconditionally calls disable_irq()
on pex_rst_irq, which causes issues in Root Port mode where this IRQ is
not registered.
Fix this by only disabling the PERST# IRQ when operating in Endpoint mode,
where the interrupt is actually registered and used to detect PERST#
assertion/deassertion from the host.
Fixes: c57247f940 ("PCI: tegra: Add support for PCIe endpoint mode in Tegra194")
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
Link: https://patch.msgid.link/20260324190755.1094879-6-mmaddireddy@nvidia.com
As per PCIe CEM r6.0, sec 2.3, the PCIe Endpoint device should be in D3cold
to assert WAKE# pin. The previous workaround that forced downstream devices
to D0 before taking the link to L2 cited PCIe r4.0, sec 5.2, "Link State
Power Management"; however, that spec does not explicitly require putting
the device into D0 and only indicates that power removal may be initiated
without transitioning to D3hot.
Remove the D0 workaround so that Endpoint devices can use wake
functionality (WAKE# from D3). With some Endpoints the link may not enter
L2 when they remain in D3, but the Root Port continues with the usual flow
after PME timeout, so there is no functional issue.
Fixes: 56e15a238d ("PCI: tegra: Add Tegra194 PCIe support")
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://patch.msgid.link/20260324190755.1094879-5-mmaddireddy@nvidia.com
After the link reaches a Detect-related LTSSM state, disable LTSSM so it
does not keep toggling between Polling and Detect. Do this by polling for
the Detect state first, then clearing APPL_CTRL_LTSSM_EN in both
tegra_pcie_dw_pme_turnoff() and pex_ep_event_pex_rst_assert().
Fixes: 56e15a238d ("PCI: tegra: Add Tegra194 PCIe support")
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://patch.msgid.link/20260324190755.1094879-4-mmaddireddy@nvidia.com
On surprise link down, LTSSM state transits from L0 -> Recovery.RcvrLock ->
Recovery.RcvrSpeed -> Gen1 Recovery.RcvrLock -> Detect. Recovery.RcvrLock
and Recovery.RcvrSpeed transit times are 24 ms and 48 ms respectively, so
the total time from L0 to Detect is ~96 ms. Increase the poll timeout to
120 ms to account for this.
While at it, add LTSSM state defines for Detect-related states and use them
in the poll condition. Use readl_poll_timeout() instead of
readl_poll_timeout_atomic() in tegra_pcie_dw_pme_turnoff() since that path
runs in non-atomic context.
Fixes: 56e15a238d ("PCI: tegra: Add Tegra194 PCIe support")
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://patch.msgid.link/20260324190755.1094879-3-mmaddireddy@nvidia.com
As per PCIe r7.0, sec 5.3.3.2.1, after sending PME_Turn_Off message, Root
Port should wait for 1-10 msec for PME_TO_Ack message. Currently, driver is
polling for 10 msec with 1 usec delay which is aggressive. Use existing
macro PCIE_PME_TO_L2_TIMEOUT_US to poll for 10 msec with 1 msec delay.
Since this function is used in non-atomic context only, use non-atomic poll
function.
Fixes: 56e15a238d ("PCI: tegra: Add Tegra194 PCIe support")
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://patch.msgid.link/20260324190755.1094879-2-mmaddireddy@nvidia.com
Rockchip platforms provide a 64x4 bytes debug FIFO to trace the LTSSM
transition and data rate change history. These will be useful for debugging
issues such as link failure, etc.
Hence, expose these information over pcie_ltssm_state_transition
tracepoint.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
[mani: commit log]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Link: https://patch.msgid.link/1774403912-210670-4-git-send-email-shawn.lin@rock-chips.com
In the PCIe PHY init for the i.MX95, the reference clock source selection
uses a conditional instead of always passing the mask. This currently
breaks functionality if the internal refclk is used.
To fix this issue, always pass IMX95_PCIE_REF_USE_PAD as the mask and clear
bit if external refclk is not used. This essentially swaps the parameters.
Fixes: d8574ce57d ("PCI: imx6: Add external reference clock input mode support")
Signed-off-by: Franz Schnyder <franz.schnyder@toradex.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Richard Zhu <hongxing.zhu@nxp.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20260325093118.684142-1-fra.schnyder@gmail.com
Tegra Endpoint exposes three 64-bit BARs at indices 0, 2, and 4:
- BAR0+BAR1: EPF test/data (programmable 64-bit BAR)
- BAR2+BAR3: MSI-X table (hardware-backed)
- BAR4+BAR5: DMA registers (hardware-backed)
Update tegra_pcie_epc_features so that BAR2 is BAR_RESERVED with
PCI_EPC_BAR_RSVD_MSIX_TBL_RAM (64 KB) & PCI_EPC_BAR_RSVD_MSIX_PBA_RAM
(64 KB) and BAR4 is BAR_RESERVED with PCI_EPC_BAR_RSVD_DMA_CTRL_MMIO (4KB).
This keeps CONSECUTIVE_BAR_TEST working while allowing the host to use
64-bit BAR2 (MSI-X) and BAR4 (DMA).
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Link: https://patch.msgid.link/20260324080857.916263-4-mmaddireddy@nvidia.com
The Tegra194/234 Endpoint does not support the Resizable BAR capability,
but BAR0 can be programmed to different sizes via the DBI2 BAR registers
in dw_pcie_ep_set_bar_programmable(). The BAR0 size is set once during
initialization.
Remove the fixed 1MB limit from pci_epc_features so Endpoint function
drivers can configure the BAR0 size they need.
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Link: https://patch.msgid.link/20260324080857.916263-3-mmaddireddy@nvidia.com
On NXP i.MX7D, i.MX8MM, and i.MX8MQ chipsets, MSIs from the endpoints won't
be received by the iMSI-RX MSI controller if the Root Port MSI capability
is disabled.
Even though the Root Port MSIs won't be received by the iMSI-RX controller
due to design, these chipsets have some weird hardware bug that prevents
the endpoint MSIs from reaching when the Root Port MSI capability is
disabled.
Hence, introduce a new flag, 'dw_pcie_rp::keep_rp_msi_en', set it for the
above mentioned SoCs, and always keep the Root Port MSI capability when
this flag is set.
Note that by keeping Root Port MSI capability, Root Port MSIs such as AER,
PME and others won't be received by default. So users need to use
workarounds such as passing 'pcie_pme=nomsi' cmdline param.
Fixes: f5cd8a929c ("PCI: dwc: Remove MSI/MSIX capability for Root Port if iMSI-RX is used as MSI controller")
Suggested-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
[mani: commit log]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
[bhelgaas: fix typos]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260331085252.1243108-1-hongxing.zhu@nxp.com
kstrtou32_from_user() returns int, but the return value was stored in
a u32 variable 'val', risking sign loss. Use a dedicated int variable
to correctly handle the return code.
Fixes: 4fbfa17f9a ("PCI: dwc: Add debugfs based Silicon Debug support for DWC")
Signed-off-by: Hans Zhang <18255117159@163.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://patch.msgid.link/20260401023048.4182452-1-18255117159@163.com
Replace direct indexing of pcie_link_speed[] with the new helper
pcie_get_link_speed() in all DesignWare core and glue drivers. This
ensures that out-of-range generation numbers do not cause out-of-bounds
accesses when the helper returns PCI_SPEED_UNKNOWN, and prepares for
the removal of the range check in of_pci_get_max_link_speed().
The actual validation of the "max-link-speed" DT property (e.g., fallback
to a safe default and warning) is added in subsequent patches for each
driver that reads the property.
Signed-off-by: Hans Zhang <18255117159@163.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://patch.msgid.link/20260313165522.123518-3-18255117159@163.com
Qcom PCIe Root Ports advertise hotplug capability in hardware, but do not
support hotplug command completion. As a result, the hotplug commands
issued by the pciehp driver never gets completion notification, leading to
repeated timeout warnings and multi-second delays during boot and
suspend/resume.
Commit a54db86ddc ("PCI: qcom: Do not advertise hotplug capability for
IPs v2.7.0 and v1.9.0") mistakenly assumed that the Root Ports doesn't
support Hotplug due to timeouts and disabled the Hotplug functionality
altogether. But the Root Ports does support reporting Hotplug events like
DL_Up/Down events.
So to fix the command completion timeout issues, just set the No Command
Completed Support (NCCS) bit and enable Hotplug in Slot Capability field
back.
Fixes: a54db86ddc ("PCI: qcom: Do not advertise hotplug capability for IPs v2.7.0 and v1.9.0")
Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
[mani: renamed function, commit log and added comment]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Tested-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> # Hamoa CRD, tunneled link
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://patch.msgid.link/20260314-hotplug-v1-1-96ac87d93867@oss.qualcomm.com
Extend the DesignWare PCIe controller's debugfs statistical counter
interface with event definitions from groups 5 through 7 as documented
in the DWC PCIe Databook (version 6.30a, section 3.8.2.3, Tables 3-59,
3-60, 3-61). These counters provide visibility into Layer1 non-error
events (link state transitions,ASPM, L1 substates), Layer2 DLLP
exchanges, and Layer3 TLP transactions.
The counters are exposed under the debugfs statistical counter directory,
allowing users to monitor link behavior and diagnose PCIe protocol issues
more effectively.
Co-developed-by: Cheng Xin <chengqin195275@126.com>
Signed-off-by: Cheng Xin <chengqin195275@126.com>
Signed-off-by: Hans Zhang <18255117159@163.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://patch.msgid.link/20260307020152.1224518-1-18255117159@163.com
The imx_pcie_assert_core_reset() and imx_pcie_deassert_core_reset()
functions are primarily intended to reset the RC controller itself, not
the remote PCIe endpoint devices. However, the PERST# GPIO control was
previously embedded within these functions, which conflates two distinct
reset operations.
Move the PERST# GPIO handling into a dedicated function
imx_pcie_assert_perst(). This makes the code more maintainable and
prepares for parsing the reset-gpios property according to the new
Root Port DT binding in subsequent patches.
No functional change is intended.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Richard Zhu <hongxing.zhu@nxp.com>
Link: https://patch.msgid.link/20260306030456.1032815-1-sherry.sun@nxp.com
The function imx_pcie_deassert_core_reset() always returns 0 and the
return value is not used meaningfully by its callers.
Change the return type from int to void to simplify the code and
remove unnecessary error handling paths. No functional change intended.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Richard Zhu <hongxing.zhu@nxp.com>
Link: https://patch.msgid.link/20260306021247.991976-1-sherry.sun@nxp.com
On i.MX6SX, the LTSSM registers become inaccessible after the
PME_Turn_Off message is sent to the link. So there is no way to verify
whether the link has entered L2/L3 Ready state or not.
Hence, set IMX_PCIE_FLAG_SKIP_L23_READY flag for i.MX6SX SoC to skip the
L2/L3 Ready state polling and let the DWC core wait for 10ms after sending
the PME_Turn_Off message as per the PCIe spec r6.0, sec 5.3.3.2.1.
Fixes: a528d1a725 ("PCI: imx6: Use DWC common suspend resume method")
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
[mani: commit log]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20260228080925.1558395-1-hongxing.zhu@nxp.com
R-Car S4 Series (R8A779F[4-7]*) EP controller uses a 4K minimum iATU region
size (CX_ATU_MIN_REGION_SIZE = 4K) as per R19UH0161EJ0130 Rev.1.30. Also,
the controller itself can only be configured in the range 4 KB to 64 KB, so
the current 1 MB alignment requirement is incorrect.
Hence, change the alignment to the min size 4K as per the documentation.
This also fixes needless unusability of BAR4 on this platform when the
target address is fixed, such as for doorbell targets.
Fixes: e311b3834d ("PCI: rcar-gen4: Add endpoint mode support")
Signed-off-by: Koichiro Den <den@valinux.co.jp>
[mani: commit log]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Link: https://patch.msgid.link/20260305151050.1834007-1-den@valinux.co.jp
R-Car Gen4 (S4) endpoint controller implements the PCIe Resizable BAR
capability for BAR0 and BAR2. Advertise them as BAR_RESIZABLE so that EPF
requested BAR sizes are reflected to the host.
Signed-off-by: Koichiro Den <den@valinux.co.jp>
[commit log]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Link: https://patch.msgid.link/20260210160315.2272930-1-den@valinux.co.jp
Add driver for the ESWIN PCIe Root Complex based on the DesignWare PCIe
core, IP revision 5.96a. The PCIe Gen.3 Root Complex supports data rate of
8 GT/s and x4 lanes, with INTx and MSI interrupt capability.
Signed-off-by: Yu Ning <ningyu@eswincomputing.com>
Signed-off-by: Yanghui Ou <ouyanghui@eswincomputing.com>
Signed-off-by: Senchuan Zhang <zhangsenchuan@eswincomputing.com>
[mani: renamed "EIC7700" to "ESWIN", added maintainers entry, removed async probe]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
[bhelgaas: add driver tag in subject]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20260227111808.1996-1-zhangsenchuan@eswincomputing.com
The driver is pretty generic and would fit for either PCI Slots or
endpoints connected to PCI ports, so rename the driver and module as
pci-pwrctrl-generic.
Suggested-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Link: https://patch.msgid.link/20260220-topic-sm8650-ayaneo-pocket-s2-base-v5-3-1ad79caa1efa@linaro.org
The current EPC core design relies on an EPC driver disabling all BARs by
default. An EPF driver will then enable the BARs that it wants to enabled.
This design is there because there is no epc->ops->disable_bar().
(There is a epc->ops->clear_bar(), but that is only to disable a BAR that
has been enabled using epc->ops->set_bar() first.)
By default, an EPF driver will not be able to get/enable BARs that are
marked as BAR_RESERVED or BAR_DISABLED (see pci_epc_get_next_free_bar()).
Since the current EPC code design requires an EPC driver to disable all
BARs by default, move this to DWC common code from each glue driver.
BAR_RESERVED BARs are not disabled by default because these BARs are
hardware backed, and should only be disabled explicitly by an EPF driver
if absolutely necessary for the EPF driver to function correctly.
(This is similar to how e.g. NVMe may have vendor specific BARs outside of
the mandatory BAR0 which contains the NVMe registers.)
Note that there is currently no EPC operation to disable a BAR that has not
first been programmed using pci_epc_set_bar(). If an EPF driver ever wants
to disable a BAR marked as BAR_RESERVED, a disable_bar() operation would
have to be added first.
No functional changes intended.
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Tested-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Tested-by: Koichiro Den <den@valinux.co.jp>
Reviewed-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260312130229.2282001-19-cassel@kernel.org
