Prevent PMECC errors when reading from AMD/Spansion S34ML02G1 flash on
SAM9X60 SoC, after switching to ONFI timing mode 3.
From reading the S34ML02G1 and the SAM9X60 datasheets again, it seems
like we have to wait tREA after rising RE# before sampling the data.
Thus pulse must be at least tREA.
The previous approach to set this timing worked on sam9g20 and sama5d2
with the same flash (S34ML02G1), probably because those have a slower
mck clock rate and thus the resolution of the timings setup is not as
tight as with sam9x60.
The approach to fix the issue was carried over from u-boot, which itself
got it from at91bootstrap. It has been successfully tested in
at91bootstrap, U-Boot and Linux on sam9x60 and sama5d2, for several
months here.
Link: https://github.com/linux4sam/at91bootstrap/issues/174
Link: e2dfd8141d
Link: https://lore.kernel.org/u-boot/20240415075755.780653-1-ada@thorsis.com/
Link: 344e2f2cd4
Cc: Li Bin <bin.li@microchip.com>
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The s3c2410 NAND driver still supports S3C64xx platform, which in
general is supported in the kernel. There are however no references of
"s3c6400-nand" platform device ID or "s3c24xx-nand" driver, thus this
driver cannot be instantiated for S3C64xx platform and is basically
unused.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
On Octal DTR capable flashes like Micron Xcella the writes cannot start
or end at an odd address in Octal DTR mode. Extra 0xff bytes need to be
appended or prepended to make sure the start address and end address are
even. 0xff is used because on NOR flashes a program operation can only
flip bits from 1 to 0, not the other way round. 0 to 1 flip needs to
happen via erases.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Signed-off-by: Luke Wang <ziniu.wang_1@nxp.com>
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20250708091646.292-2-ziniu.wang_1@nxp.com
On Octal DTR capable flashes like Micron Xcella reads cannot start or
end at an odd address in Octal DTR mode. Extra bytes need to be read at
the start or end to make sure both the start address and length remain
even.
To avoid allocating too much extra memory, thereby putting unnecessary
memory pressure on the system, the temporary buffer containing the extra
padding bytes is capped at PAGE_SIZE bytes. The rest of the 2-byte
aligned part should be read directly in the main buffer.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Signed-off-by: Luke Wang <ziniu.wang_1@nxp.com>
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20250708091646.292-1-ziniu.wang_1@nxp.com
Samsung S3C24xx family of SoCs was removed from the Linux kernel in the
commit 61b7f8920b ("ARM: s3c: remove all s3c24xx support"), in January
2023. There are no in-kernel users of its compatibles and platform IDs.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Change the 'ret' variable from u32 to int in pl35x_nand_probe() to store
negative error codes or zero;
Storing the negative error codes in unsigned type, doesn't cause an issue
at runtime but can be confusing. Additionally, assigning negative error
codes to unsigned type may trigger a GCC warning when the -Wsign-conversion
flag is enabled.
No effect on runtime.
Signed-off-by: Qianfeng Rong <rongqianfeng@vivo.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Having setup time 0 violates tAR, tCLR of some chips, for instance
TOSHIBA TC58NVG2S3ETAI0 cannot be detected successfully (first ID byte
being read duplicated, i.e. 98 98 dc 90 15 76 14 03 instead of
98 dc 90 15 76 ...).
Atmel Application Notes postulated 1 cycle NRD_SETUP without explanation
[1], but it looks more appropriate to just calculate setup time properly.
[1] Link: https://ww1.microchip.com/downloads/aemDocuments/documents/MPU32/ApplicationNotes/ApplicationNotes/doc6255.pdf
Cc: stable@vger.kernel.org
Fixes: f9ce2eddf1 ("mtd: nand: atmel: Add ->setup_data_interface() hooks")
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Tested-by: Alexander Dahl <ada@thorsis.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
GD5F1GM9 supports a high-speed Continuous Read (CR) mode which allows
the entire memory array to be read out by a single read command
without re-issuing the 13h “Page Read to Cache” command for every page.
Datasheet summary
Feature register B0[3] (NR bit)
1 = Normal Read (default)
0 = Continuous Read (CR)
ECC status register 7Ch
Normal read: bits [3:0] → ECC status of last page
Continuous read: bits [7:4] → accumulated max bit-flips over the
whole sequential read operation.
Datasheet:
https://github.com/WT-886/DATASHEET/blob/main/GD5F1GM9-v1.0.pdf
Signed-off-by: Teng Wu <gigadevice2025@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In case OOB write is requested during a data write, ECC is currently
lost. Avoid this issue by only writing in the free spare area.
This issue has been seen with a YAFFS2 file system.
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Cc: stable@vger.kernel.org
Fixes: 2cd457f328 ("mtd: rawnand: stm32_fmc2: add STM32 FMC2 NAND flash controller driver")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Since commit ddaad4ad77 ("mtd: nand: qpic_common: prevent out of
bounds access of BAM arrays"), the {cmd,data}_sgl_nitems members in
the 'bam_transaction' structure are containing the number of elements
in the cmd/data scatter-gather lists.
Change the qcom_clear_bam_transaction() function to use these numbers
while reinitializing the sg lists instead of recomputing the number of
elements to make it less error prone.
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Acked-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
If a ma35_nand_chip_init() call fails, then a reference to 'nand_np' still
needs to be released.
Use for_each_child_of_node_scoped() to fix the issue.
Fixes: 5abb5d414d ("mtd: rawnand: nuvoton: add new driver for the Nuvoton MA35 SoC")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Intel Discrete Graphics non-volatile memory is only present on Intel
discrete graphics devices, and its auxiliary device is instantiated by
the Intel i915 and Xe2 DRM drivers. Hence add dependencies on DRM_I915
and DRM_XE, to prevent asking the user about this driver when
configuring a kernel without Intel graphics support.
Fixes: ceb5ab3cb6 ("mtd: add driver for intel graphics non-volatile memory device")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Instances are happier that way and it makes more sense anyway -
the only part of the result that is related to partition we are given
is the start sector, and that has been filled in by the caller.
Everything else is a function of the disk. Only one instance
(DASD) is ever looking at anything other than bdev->bd_disk and
that one is trivial to adjust.
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Apart from a binding conversion to yaml, only minor changes/small fixes
have been merged.
* Raw NAND changes:
Various controller drivers received minor fixes like DMA mapping checks,
better timing derivations or bitflip statistics.
It has also been discovered that some Hynix NAND flashes were not
supporting read-retries, which is not properly supported.
* SPI NAND changes:
In order to support high-speed modes, certain chips need extra
configuration like adding more dummy cycles. This is now possible,
especially on Winbond chips.
Aside from that, Gigadevice gets support for a new chip (GD5F1GM9).
* SPI NOR changes:
A notable changes is the fix for exiting 4-byte addressing on Infineon
SEMPER flashes. These flashes do not support the standard EX4B
opcode (E9h), and use a vendor-specific opcode (B8h) instead.
There is also a fix for unlocking flashes that are write-protected at
power-on. This was caused by using an uninitialized mtd_info in
spi_nor_try_unlock_all().
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmiLn/sACgkQJWrqGEe9
VoTGowf/c6kynDuMlQbTANv/UIYX/LRFZsnIx0LB32LWrhLaUIBsbFxejyt07WG9
ryej+xRUtSHGsqMIw+B/PjvA4hUNLdsSwO/udIwstXNQjJcO9OKp/ucpvlxLzIha
REq8IifvT9vLLA+Efoq2L25dM14KjuFCAjwm3GH/SmdTOqPhI/Bbnx4vRWIPeXrx
XZ69ovIiu5NqLTD5IFGsu+omhbFWlDtVALtKNknrTOXWrjLZhDpieO4f7M9rvru6
OwazFQAWuixzqZRMFqvOzu8KUDnOHi9gHrzi6tS7T1zBUDz9ywdBtaHYCd7VlMJh
uV1wjUdWjnIh9E8R/llv3D+ko1Ya1w==
=IS/d
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd updates from Miquel Raynal:
"MTD changes:
- Apart from a binding conversion to yaml, only minor changes/small
fixes have been merged.
Raw NAND changes:
- Minor fixes for various controller drivers like DMA mapping checks,
better timing derivations or bitflip statistics.
- some Hynix NAND flashes were not supporting read-retries, so don't
even try to do it
SPI NAND changes:
- In order to support high-speed modes, certain chips need extra
configuration like adding more dummy cycles. This is now possible,
especially on Winbond chips.
- Aside from that, Gigadevice gets support for a new chip (GD5F1GM9).
SPI NOR changes:
- A notable changes is the fix for exiting 4-byte addressing on
Infineon SEMPER flashes. These flashes do not support the standard
EX4B opcode (E9h), and use a vendor-specific opcode (B8h) instead.
- There is also a fix for unlocking flashes that are write-protected
at power-on. This was caused by using an uninitialized mtd_info in
spi_nor_try_unlock_all()"
* tag 'mtd/for-6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (26 commits)
mtd: spinand: winbond: Add comment about the maximum frequency
mtd: spinand: winbond: Enable high-speed modes on w35n0xjw
mtd: spinand: winbond: Enable high-speed modes on w25n0xjw
mtd: spinand: Add a ->configure_chip() hook
mtd: spinand: Add a frequency field to all READ_FROM_CACHE variants
mtd: spinand: Fix macro alignment
spi: spi-mem: Take into account the actual maximum frequency
spi: spi-mem: Use picoseconds for calculating the op durations
mtd: rawnand: atmel: set pmecc data setup time
mtd: spinand: propagate spinand_wait() errors from spinand_write_page()
mtd: rawnand: fsmc: Add missing check after DMA map
mtd: rawnand: rockchip: Add missing check after DMA map
mtd: rawnand: hynix: don't try read-retry on SLC NANDs
mtd: rawnand: atmel: Fix dma_mapping_error() address
mtd: nand: brcmnand: fix mtd corrected bits stat
mtd: rawnand: renesas: Add missing check after DMA map
mtd: spinand: gigadevice: Add support for GD5F1GM9 chips
mtd: nand: brcmnand: replace manual string choices with standard helpers
mtd: map: Don't use "proxy" headers
mtd: spi-nor: Fix spi_nor_try_unlock_all()
...
UBIFS:
- No longer use write_cache_pages()
UBI:
- Removal of an unused function
-----BEGIN PGP SIGNATURE-----
iQJKBAABCAA0FiEEdgfidid8lnn52cLTZvlZhesYu8EFAmiJJ9UWHHJpY2hhcmRA
c2lnbWEtc3Rhci5hdAAKCRBm+VmF6xi7wf4gEACYUeCKRPJOc6qoCnhsqONKymE/
jVXxCWOBqpoyF0wtt0BXcS46FpXzKufb2U2BHL6j2/v77qXBYv/KenT1PJe9llXH
CNoGQb/zgr7cGFULetE12iaTJYxcIyaWfCk1pH7+n8JWeLwTQE66P1PdK5uEzHEp
5gtDyOic8hSIShLBC01/Td9FVRD3A79DhZUP2WDYxsiZGbA93IvE0RpV2x6iBnOG
uOzcHAZfnnlO22GoCqcQe5xaqOo3f4mJch6StEDLAs7EN1jvZMSH4wjM6Sbl+R4Z
3rzLE0LwqItVZCA9yBsZWZLvaGWhS44UH6HXiluTh0a6NzSoyOAg2U+4vU3frfbY
Kbnum9Rujc3NaVyHHHKmpDWEglj1bk8oN0EXVIOx887JkLjJF0FkSlo+gXp+cA+f
C0DpsSdJp6XhJsD60dp4gnas8stISmEN0xs/qgICXMo2WByIZlLtsOgBNwfocD8t
PtckkemupulEnSb9GJ/niAJttACSQFI9DCfnZibj3PYu3OeubSD30mJs/SY6rXOR
XS9jejSKxdyhyboL9PwuSPVbD2rj/uD/uL8R2ypGbrwNyQGvqUgBQUQjnhNDiOvt
CHwCtkmoupWxJscmu34K91zrN19i/9Nw4g+/2SOBz6NvVmIknTtuBQfBL57f2ykq
tZlNwdV/e/a2WCx7dg==
=/AwZ
-----END PGP SIGNATURE-----
Merge tag 'ubifs-for-linus-6.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs
Pull UBI and UBIFS updates from Richard Weinberger:
"UBIFS:
- No longer use write_cache_pages()
UBI:
- Remove an unused function"
* tag 'ubifs-for-linus-6.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs:
ubifs: stop using write_cache_pages
mtd: ubi: Remove unused ubi_flush
Various controller drivers received minor fixes like DMA mapping checks,
better timing derivations or bitflip statistics.
It has also been discovered that some Hynix NAND flashes were not
supporting read-retries, which is not properly supported.
* SPI NAND changes:
In order to support high-speed modes, certain chips need extra
configuration like adding more dummy cycles. This is now possible,
especially on Winbond chips.
Aside from that, Gigadevice gets support for a new chip (GD5F1GM9).
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmiLnj0ACgkQJWrqGEe9
VoSHCQf/XHxFyj3kvDzbS1qtMfEF8qLxveyucOgvPxnM0v9rDVcsdTaWBVfyJsNX
vzUPJ3J4NfWQNYo4ya/aennWt/ZCEa+tT6XI9xFp1YRizmQucC7dQLeaGp+eR0Tl
HVrPLWEVo+3vplI4EWvzwTvBYx5PBmB1t1SzDjx/SsQtG3OS9xgw/DKfV7odHBsH
REpoUY64QLRtsGL896gkohEGgAd86nqfpaFetS1S3YXfYWryEmAigrDBIQ/IMTCM
D4lLcgEw82f2Dsa7zhVtxntrfYy2xOOp34kADmbByrBjFbwmcXvKocy7Ahj2dRaq
JsCkH/Pc1wAHq5uu9GLy24aqzt0OPA==
=68JT
-----END PGP SIGNATURE-----
Merge tag 'nand/for-6.17' into mtd/next
* Raw NAND changes:
Various controller drivers received minor fixes like DMA mapping checks,
better timing derivations or bitflip statistics.
It has also been discovered that some Hynix NAND flashes were not
supporting read-retries, which is not properly supported.
* SPI NAND changes:
In order to support high-speed modes, certain chips need extra
configuration like adding more dummy cycles. This is now possible,
especially on Winbond chips.
Aside from that, Gigadevice gets support for a new chip (GD5F1GM9).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Notable changes:
- Fix exiting 4-byte addressing on Infineon SEMPER flashes. These
flashes do not support the standard EX4B opcode (E9h), and use a
vendor-specific opcode (B8h) instead.
- Fix unlocking of flashes that are write-protected at power-on. This
was caused by using an uninitialized mtd_info in
spi_nor_try_unlock_all().
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQTlUWNzXGEo3bFmyIR4drqP028CQUCaIIcbAAKCRAR4drqP028
CcnDAQDj6YyRac/AqiKa+W0KL5n0AneymQtb/Pjkme2DaV++cwD/Slfk2ljsO5zN
cAhKd6ZKOuu1BhKgHAFg577UNAxs2A8=
=mXJz
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-6.17' into mtd/next
SPI NOR changes for 6.17
Notable changes:
- Fix exiting 4-byte addressing on Infineon SEMPER flashes. These
flashes do not support the standard EX4B opcode (E9h), and use a
vendor-specific opcode (B8h) instead.
- Fix unlocking of flashes that are write-protected at power-on. This
was caused by using an uninitialized mtd_info in
spi_nor_try_unlock_all().
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
non-drm:
rust:
- make ETIMEDOUT available
- add size constants up to SZ_2G
- add DMA coherent allocation bindings
mtd:
- driver for Intel GPU non-volatile storage
i2c
- designware quirk for Intel xe
core:
- atomic helpers: tune enable/disable sequences
- add task info to wedge API
- refactor EDID quirks
- connector: move HDR sink to drm_display_info
- fourcc: half-float and 32-bit float formats
- mode_config: pass format info to simplify
dma-buf:
- heaps: Give CMA heap a stable name
ci:
- add device tree validation and kunit
displayport:
- change AUX DPCD access probe address
- add quirk for DPCD probe
- add panel replay definitions
- backlight control helpers
fbdev:
- make CONFIG_FIRMWARE_EDID available on all arches
fence:
- fix UAF issues
format-helper:
- improve tests
gpusvm:
- introduce devmem only flag for allocation
- add timeslicing support to GPU SVM
ttm:
- improve eviction
sched:
- tracing improvements
- kunit improvements
- memory leak fixes
- reset handling improvements
color mgmt:
- add hardware gamma LUT handling helpers
bridge:
- add destroy hook
- switch to reference counted drm_bridge allocations
- tc358767: convert to devm_drm_bridge_alloc
- improve CEC handling
panel:
- switch to reference counter drm_panel allocations
- fwnode panel lookup
- Huiling hl055fhv028c support
- Raspberry Pi 7" 720x1280 support
- edp: KDC KD116N3730A05, N160JCE-ELL CMN, N116BCJ-EAK
- simple: AUO P238HAN01
- st7701: Winstar wf40eswaa6mnn0
- visionox: rm69299-shift
- Renesas R61307, Renesas R69328 support
- DJN HX83112B
hdmi:
- add CEC handling
- YUV420 output support
xe:
- WildCat Lake support
- Enable PanthorLake by default
- mark BMG as SRIOV capable
- update firmware recommendations
- Expose media OA units
- aux-bux support for non-volatile memory
- MTD intel-dg driver for non-volatile memory
- Expose fan control and voltage regulator in sysfs
- restructure migration for multi-device
- Restore GuC submit UAF fix
- make GEM shrinker drm managed
- SRIOV VF Post-migration recovery of GGTT nodes
- W/A additions/reworks
- Prefetch support for svm ranges
- Don't allocate managed BO for each policy change
- HWMON fixes for BMG
- Create LRC BO without VM
- PCI ID updates
- make SLPC debugfs files optional
- rework eviction rejection of bound external BOs
- consolidate PAT programming logic for pre/post Xe2
- init changes for flicker-free boot
- Enable GuC Dynamic Inhibit Context switch
i915:
- drm_panic support for i915/xe
- initial flip queue off by default for LNL/PNL
- Wildcat Lake Display support
- Support for DSC fractional link bpp
- Support for simultaneous Panel Replay and Adaptive sync
- Support for PTL+ double buffer LUT
- initial PIPEDMC event handling
- drm_panel_follower support
- DPLL interface renames
- allocate struct intel_display dynamically
- flip queue preperation
- abstract DRAM detection better
- avoid GuC scheduling stalls
- remove DG1 force probe requirement
- fix MEI interrupt handler on RT kernels
- use backlight control helpers for eDP
- more shared display code refactoring
amdgpu:
- add userq slot to INFO ioctl
- SR-IOV hibernation support
- Suspend improvements
- Backlight improvements
- Use scaling for non-native eDP modes
- cleaner shader updates for GC 9.x
- Remove fence slab
- SDMA fw checks for userq support
- RAS updates
- DMCUB updates
- DP tunneling fixes
- Display idle D3 support
- Per queue reset improvements
- initial smartmux support
amdkfd:
- enable KFD on loongarch
- mtype fix for ext coherent system memory
radeon:
- CS validation additional GL extensions
- drop console lock during suspend/resume
- bump driver version
msm:
- VM BIND support
- CI: infrastructure updates
- UBWC single source of truth
- decouple GPU and KMS support
- DP: rework I/O accessors
- DPU: SM8750 support
- DSI: SM8750 support
- GPU: X1-45 support and speedbin support for X1-85
- MDSS: SM8750 support
nova:
- register! macro improvements
- DMA object abstraction
- VBIOS parser + fwsec lookup
- sysmem flush page support
- falcon: generic falcon boot code and HAL
- FWSEC-FRTS: fb setup and load/execute
ivpu:
- Add Wildcat Lake support
- Add turbo flag
ast:
- improve hardware generations implementation
imx:
- IMX8qxq Display Controller support
lima:
- Rockchip RK3528 GPU support
nouveau:
- fence handling cleanup
panfrost:
- MT8370 support
- bo labeling
- 64-bit register access
qaic:
- add RAS support
rockchip:
- convert inno_hdmi to a bridge
rz-du:
- add RZ/V2H(P) support
- MIPI-DSI DCS support
sitronix:
- ST7567 support
sun4i:
- add H616 support
tidss:
- add TI AM62L support
- AM65x OLDI bridge support
bochs:
- drm panic support
vkms:
- YUV and R* format support
- use faux device
vmwgfx:
- fence improvements
hyperv:
- move out of simple
- add drm_panic support
-----BEGIN PGP SIGNATURE-----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=n9MO
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2025-07-30' of https://gitlab.freedesktop.org/drm/kernel
Pull drm updates from Dave Airlie:
"Highlights:
- Intel xe enable Panthor Lake, started adding WildCat Lake
- amdgpu has a bunch of reset improvments along with the usual IP
updates
- msm got VM_BIND support which is important for vulkan sparse memory
- more drm_panic users
- gpusvm common code to handle a bunch of core SVM work outside
drivers.
Detail summary:
Changes outside drm subdirectory:
- 'shrink_shmem_memory()' for better shmem/hibernate interaction
- Rust support infrastructure:
- make ETIMEDOUT available
- add size constants up to SZ_2G
- add DMA coherent allocation bindings
- mtd driver for Intel GPU non-volatile storage
- i2c designware quirk for Intel xe
core:
- atomic helpers: tune enable/disable sequences
- add task info to wedge API
- refactor EDID quirks
- connector: move HDR sink to drm_display_info
- fourcc: half-float and 32-bit float formats
- mode_config: pass format info to simplify
dma-buf:
- heaps: Give CMA heap a stable name
ci:
- add device tree validation and kunit
displayport:
- change AUX DPCD access probe address
- add quirk for DPCD probe
- add panel replay definitions
- backlight control helpers
fbdev:
- make CONFIG_FIRMWARE_EDID available on all arches
fence:
- fix UAF issues
format-helper:
- improve tests
gpusvm:
- introduce devmem only flag for allocation
- add timeslicing support to GPU SVM
ttm:
- improve eviction
sched:
- tracing improvements
- kunit improvements
- memory leak fixes
- reset handling improvements
color mgmt:
- add hardware gamma LUT handling helpers
bridge:
- add destroy hook
- switch to reference counted drm_bridge allocations
- tc358767: convert to devm_drm_bridge_alloc
- improve CEC handling
panel:
- switch to reference counter drm_panel allocations
- fwnode panel lookup
- Huiling hl055fhv028c support
- Raspberry Pi 7" 720x1280 support
- edp: KDC KD116N3730A05, N160JCE-ELL CMN, N116BCJ-EAK
- simple: AUO P238HAN01
- st7701: Winstar wf40eswaa6mnn0
- visionox: rm69299-shift
- Renesas R61307, Renesas R69328 support
- DJN HX83112B
hdmi:
- add CEC handling
- YUV420 output support
xe:
- WildCat Lake support
- Enable PanthorLake by default
- mark BMG as SRIOV capable
- update firmware recommendations
- Expose media OA units
- aux-bux support for non-volatile memory
- MTD intel-dg driver for non-volatile memory
- Expose fan control and voltage regulator in sysfs
- restructure migration for multi-device
- Restore GuC submit UAF fix
- make GEM shrinker drm managed
- SRIOV VF Post-migration recovery of GGTT nodes
- W/A additions/reworks
- Prefetch support for svm ranges
- Don't allocate managed BO for each policy change
- HWMON fixes for BMG
- Create LRC BO without VM
- PCI ID updates
- make SLPC debugfs files optional
- rework eviction rejection of bound external BOs
- consolidate PAT programming logic for pre/post Xe2
- init changes for flicker-free boot
- Enable GuC Dynamic Inhibit Context switch
i915:
- drm_panic support for i915/xe
- initial flip queue off by default for LNL/PNL
- Wildcat Lake Display support
- Support for DSC fractional link bpp
- Support for simultaneous Panel Replay and Adaptive sync
- Support for PTL+ double buffer LUT
- initial PIPEDMC event handling
- drm_panel_follower support
- DPLL interface renames
- allocate struct intel_display dynamically
- flip queue preperation
- abstract DRAM detection better
- avoid GuC scheduling stalls
- remove DG1 force probe requirement
- fix MEI interrupt handler on RT kernels
- use backlight control helpers for eDP
- more shared display code refactoring
amdgpu:
- add userq slot to INFO ioctl
- SR-IOV hibernation support
- Suspend improvements
- Backlight improvements
- Use scaling for non-native eDP modes
- cleaner shader updates for GC 9.x
- Remove fence slab
- SDMA fw checks for userq support
- RAS updates
- DMCUB updates
- DP tunneling fixes
- Display idle D3 support
- Per queue reset improvements
- initial smartmux support
amdkfd:
- enable KFD on loongarch
- mtype fix for ext coherent system memory
radeon:
- CS validation additional GL extensions
- drop console lock during suspend/resume
- bump driver version
msm:
- VM BIND support
- CI: infrastructure updates
- UBWC single source of truth
- decouple GPU and KMS support
- DP: rework I/O accessors
- DPU: SM8750 support
- DSI: SM8750 support
- GPU: X1-45 support and speedbin support for X1-85
- MDSS: SM8750 support
nova:
- register! macro improvements
- DMA object abstraction
- VBIOS parser + fwsec lookup
- sysmem flush page support
- falcon: generic falcon boot code and HAL
- FWSEC-FRTS: fb setup and load/execute
ivpu:
- Add Wildcat Lake support
- Add turbo flag
ast:
- improve hardware generations implementation
imx:
- IMX8qxq Display Controller support
lima:
- Rockchip RK3528 GPU support
nouveau:
- fence handling cleanup
panfrost:
- MT8370 support
- bo labeling
- 64-bit register access
qaic:
- add RAS support
rockchip:
- convert inno_hdmi to a bridge
rz-du:
- add RZ/V2H(P) support
- MIPI-DSI DCS support
sitronix:
- ST7567 support
sun4i:
- add H616 support
tidss:
- add TI AM62L support
- AM65x OLDI bridge support
bochs:
- drm panic support
vkms:
- YUV and R* format support
- use faux device
vmwgfx:
- fence improvements
hyperv:
- move out of simple
- add drm_panic support"
* tag 'drm-next-2025-07-30' of https://gitlab.freedesktop.org/drm/kernel: (1479 commits)
drm/tidss: oldi: convert to devm_drm_bridge_alloc() API
drm/tidss: encoder: convert to devm_drm_bridge_alloc()
drm/amdgpu: move reset support type checks into the caller
drm/amdgpu/sdma7: re-emit unprocessed state on ring reset
drm/amdgpu/sdma6: re-emit unprocessed state on ring reset
drm/amdgpu/sdma5.2: re-emit unprocessed state on ring reset
drm/amdgpu/sdma5: re-emit unprocessed state on ring reset
drm/amdgpu/gfx12: re-emit unprocessed state on ring reset
drm/amdgpu/gfx11: re-emit unprocessed state on ring reset
drm/amdgpu/gfx10: re-emit unprocessed state on ring reset
drm/amdgpu/gfx9.4.3: re-emit unprocessed state on kcq reset
drm/amdgpu/gfx9: re-emit unprocessed state on kcq reset
drm/amdgpu: Add WARN_ON to the resource clear function
drm/amd/pm: Use cached metrics data on SMUv13.0.6
drm/amd/pm: Use cached data for min/max clocks
gpu: nova-core: fix bounds check in PmuLookupTableEntry::new
drm/amdgpu: Replace HQD terminology with slots naming
drm/amdgpu: Add user queue instance count in HW IP info
drm/amd/amdgpu: Add helper functions for isp buffers
drm/amd/amdgpu: Initialize swnode for ISP MFD device
...
Clarify that Winbond octal capable chips may be clocked at up to 166MHz,
which is their absolute maximum.
No per-operation maximum value (captured with a "0" in the table)
involves that in these cases the maximum frequency of the chip applies,
ie. the one commonly described in the DT.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
w35n0xjw chips can run at up to 166MHz in octal mode, but this is only
possible after programming various VCR registers.
Implement the new ->configure_chip() hook for this purpose.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
w25n0xjw chips have a high-speed capability hidden in a configuration
register. Once enabled, dual/quad SDR reads may be performed at a much
higher frequency.
Implement the new ->configure_chip() hook for this purpose and configure
the SR4 register accordingly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
There is already a manufacturer hook, which is manufacturer specific but
not chip specific. We no longer have access to the actual NAND identity
at this stage so let's add a per-chip configuration hook to align the
chip configuration (if any) with the core's setting.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
These macros had initially no frequency field. When I added the "maximum
operation frequency" field, I did it initially on very common macros and
I decided to add an optional field for that (with VA_ARGS) in order to
prevent massively unreadable changes. I then added new variants in the
spinand.h header, and requested a frequency field for them by
default. Some times later, I also added maximum frequencies to other
existing variants, but I did it incorrectly, without noticing I was
wrong because the field was optional.
This mix is error prone, so let's do what I should have done since the
very beginning: add a frequency field to all READ_FROM_CACHE variants.
There is no functional change.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In order to pick the best variant, the duration of each typical
operation is derived and then compared. These durations are based on the
maximum capabilities of the chips, which are commonly the limiting
factors. However there are other possible limiting pieces, such as the
hardware layout, EMC considerations and in some cases, the SPI controller
itself.
We need to take this into account to further refine our variant choice,
so let's use the actual frequency that will be used for the operation
instead of the theoretical maximum.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Setup the pmecc data setup time as 3 clock cycles for 133MHz as recommended
by the datasheet.
Fixes: f88fc122cc ("mtd: nand: Cleanup/rework the atmel_nand driver")
Reported-by: Zixun LI <admin@hifiphile.com>
Closes: https://lore.kernel.org/all/c015bb20-6a57-4f63-8102-34b3d83e0f5b@microchip.com
Suggested-by: Ada Couprie Diaz <ada.coupriediaz@arm.com>
Signed-off-by: Balamanikandan Gunasundar <balamanikandan.gunasundar@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Since commit 3d1f08b032 ("mtd: spinand: Use the external ECC engine
logic") the spinand_write_page() function ignores the errors returned
by spinand_wait(). Change the code to propagate those up to the stack
as it was done before the offending change.
Cc: stable@vger.kernel.org
Fixes: 3d1f08b032 ("mtd: spinand: Use the external ECC engine logic")
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The DMA map functions can fail and should be tested for errors.
Fixes: 058e0e847d ("mtd: rawnand: rockchip: NFC driver for RK3308, RK2928 and others")
Signed-off-by: Thomas Fourier <fourier.thomas@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Some SLC NANDs like H27U4G8F2D expose a valid JEDEC ID yet they don't
support the read-retry mechanism, and fail.
Since SLC NANDs don't require read-retry, continue only if the bits per
cell is bigger than 1.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It seems like what was intended is to test if the dma_map of the
previous line failed but the wrong dma address was passed.
Fixes: f88fc122cc ("mtd: nand: Cleanup/rework the atmel_nand driver")
Signed-off-by: Thomas Fourier <fourier.thomas@gmail.com>
Rule: add
Link: https://lore.kernel.org/stable/20250702064515.18145-2-fourier.thomas%40gmail.com
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Currently we attempt to get the amount of flipped bits from a hardware
location which is reset on every subpage. Instead obtain total flipped
bits stat from hardware accumulator. In addition identify the correct
maximum subpage corrected bits.
Signed-off-by: David Regan <dregan@broadcom.com>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The DMA map functions can fail and should be tested for errors.
Fixes: d8701fe890 ("mtd: rawnand: renesas: Add new NAND controller driver")
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Fourier <fourier.thomas@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Use kernel provided standard helper function to replace hard-coded
strings
Signed-off-by: Yuesong Li <liyuesong@vivo.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
- DEBUGFS
- Remove unneeded debugfs_file_{get,put}() instances
- Remove last remnants of debugfs_real_fops()
- Allow storing non-const void * in struct debugfs_inode_info::aux
- SYSFS
- Switch back to attribute_group::bin_attrs (treewide)
- Switch back to bin_attribute::read()/write() (treewide)
- Constify internal references to 'struct bin_attribute'
- Support cache-ids for device-tree systems
- Add arch hook arch_compact_of_hwid()
- Use arch_compact_of_hwid() to compact MPIDR values on arm64
- Rust
- Device
- Introduce CoreInternal device context (for bus internal methods)
- Provide generic drvdata accessors for bus devices
- Provide Driver::unbind() callbacks
- Use the infrastructure above for auxiliary, PCI and platform
- Implement Device::as_bound()
- Rename Device::as_ref() to Device::from_raw() (treewide)
- Implement fwnode and device property abstractions
- Implement example usage in the Rust platform sample driver
- Devres
- Remove the inner reference count (Arc) and use pin-init instead
- Replace Devres::new_foreign_owned() with devres::register()
- Require T to be Send in Devres<T>
- Initialize the data kept inside a Devres last
- Provide an accessor for the Devres associated Device
- Device ID
- Add support for ACPI device IDs and driver match tables
- Split up generic device ID infrastructure
- Use generic device ID infrastructure in net::phy
- DMA
- Implement the dma::Device trait
- Add DMA mask accessors to dma::Device
- Implement dma::Device for PCI and platform devices
- Use DMA masks from the DMA sample module
- I/O
- Implement abstraction for resource regions (struct resource)
- Implement resource-based ioremap() abstractions
- Provide platform device accessors for I/O (remap) requests
- Misc
- Support fallible PinInit types in Revocable
- Implement Wrapper<T> for Opaque<T>
- Merge pin-init blanket dependencies (for Devres)
- Misc
- Fix OF node leak in auxiliary_device_create()
- Use util macros in device property iterators
- Improve kobject sample code
- Add device_link_test() for testing device link flags
- Fix typo in Documentation/ABI/testing/sysfs-kernel-address_bits
- Hint to prefer container_of_const() over container_of()
-----BEGIN PGP SIGNATURE-----
iHQEABYKAB0WIQS2q/xV6QjXAdC7k+1FlHeO1qrKLgUCaIjkhwAKCRBFlHeO1qrK
LpXuAP9RWwfD9ZGgQZ9OsMk/0pZ2mDclaK97jcmI9TAeSxeZMgD1FHnOMTY7oSIi
iG7Muq0yLD+A5gk9HUnMUnFNrngWCg==
=jgRj
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/driver-core/driver-core
Pull driver core updates from Danilo Krummrich:
"debugfs:
- Remove unneeded debugfs_file_{get,put}() instances
- Remove last remnants of debugfs_real_fops()
- Allow storing non-const void * in struct debugfs_inode_info::aux
sysfs:
- Switch back to attribute_group::bin_attrs (treewide)
- Switch back to bin_attribute::read()/write() (treewide)
- Constify internal references to 'struct bin_attribute'
Support cache-ids for device-tree systems:
- Add arch hook arch_compact_of_hwid()
- Use arch_compact_of_hwid() to compact MPIDR values on arm64
Rust:
- Device:
- Introduce CoreInternal device context (for bus internal methods)
- Provide generic drvdata accessors for bus devices
- Provide Driver::unbind() callbacks
- Use the infrastructure above for auxiliary, PCI and platform
- Implement Device::as_bound()
- Rename Device::as_ref() to Device::from_raw() (treewide)
- Implement fwnode and device property abstractions
- Implement example usage in the Rust platform sample driver
- Devres:
- Remove the inner reference count (Arc) and use pin-init instead
- Replace Devres::new_foreign_owned() with devres::register()
- Require T to be Send in Devres<T>
- Initialize the data kept inside a Devres last
- Provide an accessor for the Devres associated Device
- Device ID:
- Add support for ACPI device IDs and driver match tables
- Split up generic device ID infrastructure
- Use generic device ID infrastructure in net::phy
- DMA:
- Implement the dma::Device trait
- Add DMA mask accessors to dma::Device
- Implement dma::Device for PCI and platform devices
- Use DMA masks from the DMA sample module
- I/O:
- Implement abstraction for resource regions (struct resource)
- Implement resource-based ioremap() abstractions
- Provide platform device accessors for I/O (remap) requests
- Misc:
- Support fallible PinInit types in Revocable
- Implement Wrapper<T> for Opaque<T>
- Merge pin-init blanket dependencies (for Devres)
Misc:
- Fix OF node leak in auxiliary_device_create()
- Use util macros in device property iterators
- Improve kobject sample code
- Add device_link_test() for testing device link flags
- Fix typo in Documentation/ABI/testing/sysfs-kernel-address_bits
- Hint to prefer container_of_const() over container_of()"
* tag 'driver-core-6.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/driver-core/driver-core: (84 commits)
rust: io: fix broken intra-doc links to `platform::Device`
rust: io: fix broken intra-doc link to missing `flags` module
rust: io: mem: enable IoRequest doc-tests
rust: platform: add resource accessors
rust: io: mem: add a generic iomem abstraction
rust: io: add resource abstraction
rust: samples: dma: set DMA mask
rust: platform: implement the `dma::Device` trait
rust: pci: implement the `dma::Device` trait
rust: dma: add DMA addressing capabilities
rust: dma: implement `dma::Device` trait
rust: net::phy Change module_phy_driver macro to use module_device_table macro
rust: net::phy represent DeviceId as transparent wrapper over mdio_device_id
rust: device_id: split out index support into a separate trait
device: rust: rename Device::as_ref() to Device::from_raw()
arm64: cacheinfo: Provide helper to compress MPIDR value into u32
cacheinfo: Add arch hook to compress CPU h/w id into 32 bits for cache-id
cacheinfo: Set cache 'id' based on DT data
container_of: Document container_of() is not to be used in new code
driver core: auxiliary bus: fix OF node leak
...
ubi_flush() was added in 2012 as part of
commit 62f384552b ("UBI: modify ubi_wl_flush function to clear work queue
for a lnum")
but has remained unused.
(It's friend ubi_wl_flush() is still used)
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
Merge series from Heiko Schocher <hs@denx.de>:
This series introduces the changes needed for trivial spi
based sensors from ABB, currently operated from userspace.
Commit ff67592cbd ("mtd: spi-nor: Introduce spi_nor_set_mtd_info()")
moved all initialization of the mtd fields at the end of spi_nor_scan().
Normally, the mtd info is only needed for the mtd ops on the device,
with one exception: spi_nor_try_unlock_all(), which will also make use
of the mtd->size parameter. With that commit, the size will always be
zero because it is not initialized. Fix that by not using the size of
the mtd_info struct, but use the size from struct spi_nor_flash_parameter.
Fixes: ff67592cbd ("mtd: spi-nor: Introduce spi_nor_set_mtd_info()")
Cc: stable@vger.kernel.org
Reported-by: Jean-Marc Ranger <jmranger@hotmail.com>
Closes: https://lore.kernel.org/all/DM6PR06MB561177323DC5207E34AF2A06C547A@DM6PR06MB5611.namprd06.prod.outlook.com/
Tested-by: Jean-Marc Ranger <jmranger@hotmail.com>
Signed-off-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20250701140426.2355182-1-mwalle@kernel.org
Infineon SEMPER flash family does not support E9h opcode as Exit 4-byte
mode (EX4B). Therefore, params->set_4byte_addr_mode is not determined by
BFPT parse. Fixup it up by introducing vendor specific EX4B opcode (B8h)
and function.
Fixes: c87c9b11c5 ("mtd: spi-nor: spansion: Determine current address mode")
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Acked-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Acked-by: Pratyush Yadav <pratyush@kernel.org>
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20250612074427.22263-1-Takahiro.Kuwano@infineon.com
'struct spi_nor_fixups' are not modified in this driver.
Constifying these structures moves some data to a read-only section, so
increases overall security, especially when the structure holds some
function pointers.
On a x86_64, with allmodconfig, as an example:
Before:
======
text data bss dec hex filename
23304 13168 0 36472 8e78 drivers/mtd/spi-nor/micron-st.o
After:
=====
text data bss dec hex filename
23560 12912 0 36472 8e78 drivers/mtd/spi-nor/micron-st.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Pratyush Yadav <pratyush@kernel.org>
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/aa641732ba707ce3690217825c3ca7373ffde4f9.1748191985.git.christophe.jaillet@wanadoo.fr
Add defines for the values of the ECC_MODE field of the NAND_DEV0_ECC_CFG
register and change both the 'qcom-nandc' and 'spi-qpic-snand' drivers to
use those instead of magic numbers.
No functional changes. This is in preparation for adding 8 bit ECC strength
support for the 'spi-qpic-snand' driver.
Reviewed-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20250702-qpic-snand-8bit-ecc-v2-1-ae2c17a30bb7@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The common QPIC code does not do any boundary checking when it handles
the command elements and scatter gater list arrays of a BAM transaction,
thus it allows to access out of bounds elements in those.
Although it is the responsibility of the given driver to allocate enough
space for all possible BAM transaction variations, however there can be
mistakes in the driver code which can lead to hidden memory corruption
issues which are hard to debug.
This kind of problem has been observed during testing the 'spi-qpic-snand'
driver. Although the driver has been fixed with a preceding patch, but it
still makes sense to reduce the chance of having such errors again later.
In order to prevent such errors, change the qcom_alloc_bam_transaction()
function to store the number of elements of the arrays in the
'bam_transaction' strucutre during allocation. Also, add sanity checks to
the qcom_prep_bam_dma_desc_{cmd,data}() functions to avoid using out of
bounds indices for the arrays.
Tested-by: Lakshmi Sowjanya D <quic_laksd@quicinc.com> # on SDX75
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Link: https://patch.msgid.link/20250618-qpic-snand-avoid-mem-corruption-v3-2-319c71296cda@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Erase command is slow on discrete graphics storage
and may overshot PCI completion timeout.
BMG introduces the ability to have non-posted erase.
Add driver support for non-posted erase with polling
for erase completion.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Reuven Abliyev <reuven.abliyev@intel.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Link: https://lore.kernel.org/r/20250617145159.3803852-9-alexander.usyskin@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Register the on-die nvm device with the mtd subsystem.
Refcount nvm object on _get and _put mtd callbacks.
For erase operation address and size should be 4K aligned.
For write operation address and size has to be 4bytes aligned.
CC: Rodrigo Vivi <rodrigo.vivi@intel.com>
CC: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Raag Jadav <raag.jadav@intel.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Co-developed-by: Tomas Winkler <tomasw@gmail.com>
Signed-off-by: Tomas Winkler <tomasw@gmail.com>
Co-developed-by: Vitaly Lubart <lubvital@gmail.com>
Signed-off-by: Vitaly Lubart <lubvital@gmail.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Link: https://lore.kernel.org/r/20250617145159.3803852-5-alexander.usyskin@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
In intel-dg, there is no access to the spi controller,
the information is extracted from the descriptor region.
CC: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Raag Jadav <raag.jadav@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Co-developed-by: Tomas Winkler <tomasw@gmail.com>
Signed-off-by: Tomas Winkler <tomasw@gmail.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Link: https://lore.kernel.org/r/20250617145159.3803852-3-alexander.usyskin@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
We need the driver-core fixes that are in 6.16-rc3 into here as well
to build on top of.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The expression '1 << EraseUnitSize' is evaluated in int, which causes
a negative result when shifting by 31 - the upper bound of the valid
range [10, 31], enforced by scan_header(). This leads to incorrect
extension when storing the result in 'erase->len' (uint64_t), producing
a large unexpected value.
Found by Linux Verification Center (linuxtesting.org) with Svace.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Ivan Stepchenko <sid@itb.spb.ru>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Dual and quad capable chips natively support dual and quad I/O variants
at up to 104MHz (1-2-2 and 1-4-4 operations). Reaching the maximum speed
of 166MHz is theoretically possible (while still unsupported in the
field) by adding a few more dummy cycles. Let's be accurate and clearly
state this limit.
Setting a maximum frequency implies adding the frequency parameter to
the macro, which is done using a variadic argument to avoid impacting
all the other drivers which already make use of this macro.
Fixes: 1ea808b4d1 ("mtd: spinand: winbond: Update the *JW chip definitions")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The default number of dummy cycles is 16 in octal I/O mode (1S-8S-8S),
and with this default configuration the maximum frequency is higher than
what is being advertised. There are higher and lower frequency
possibilities, which involve making changes in the number of dummy
cycles through the VCR register. At this stage, let's just describe the
default configuration correctly. There should be no functional change.
Fixes: 1ac5ff2f2a ("mtd: spinand: winbond: Add octal support")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
There's been a mistake when extracting the geometry of the W35N02 and
W35N04 chips from the datasheet. There is a single plane, however there
are respectively 2 and 4 LUNs. They are actually referred in the
datasheet as dies (equivalent of target), but as there is no die select
operation and the chips only feature a single configuration register for
the entire chip (instead of one per die), we can reasonably assume we
are talking about LUNs and not dies.
Reported-by: Andreas Dannenberg <dannenberg@ti.com>
Suggested-by: Vignesh Raghavendra <vigneshr@ti.com>
Fixes: 25e08bf666 ("mtd: spinand: winbond: Add support for W35N02JW and W35N04JW chips")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The idea behind this patch was to always let a "master" mtd device
available to anchor runtime PM. Historically, there was no mtd device
representing the whole storage as soon as partitions were coming into
play. The introduction of CONFIG_MTD_PARTITIONED_MASTER allowed to keep
this "master" device, but was not enabled by default to avoid breaking
existing users (otherwise the mtd device numbering would be totally
messed up with an off by 1, at least).
The approach of adding an mtd_master class on top of partitioned mtd
devices is breaking the mtd core in many creative ways, so better think
again this approach and revert the faulty changes for now.
This reverts commit 0aa7b390fc.
Fixes: 0aa7b390fc ("mtd: core: always create master device")
Tested-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The code in the ntfl write function is rather complex, and it contains
a 512 byte on-stack buffer. The combination of these two leads to using
more than the per-function stack warning limit in some configurations,
especially with KASAN enabled:
drivers/mtd/nftlcore.c:673:12: error: stack frame size (1328) exceeds limit (1280) in 'nftl_writeblock' [-Werror,-Wframe-larger-than]
Avoid this warning by moving the on-stack buffer into a separate function
that only copies one part of the device to another.
This does not really help with the total maximum stack usage in the
(non-KASAN) normal case, but it does two things:
- no single function has more than the warning limit
- the complexity goes down, so the parent function ends up
spilling few local variables, and the total actually goes
down slightly.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Move this API to the canonical timer_*() namespace.
[ tglx: Redone against pre rc1 ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/aB2X0jCKQO56WdMt@gmail.com
register a master device. This is a problem that has been there forever:
the "master" device was not always present depending on a number of
heuristics such as the presence of fixed partitions and the absence of a
Kconfig symbol to force its presence. This was a problem for runtime PM
operations which might not have the "master" device available in all
situation.
The SPI NAND subsystem has seen the introduction of DTR operations (the
equivalent of DDR transfers), which involved quite a few preparation
patches for clarifying macro names.
In the raw NAND subsystem, the brcmnand driver has been "fixed" for old
legacy SoCs with an update of the ->exec_op() hook, there has been the
introduction of a new controller driver named Loongson-1, and the
Qualcomm driver has received quite a few misc fixes as well as a new
compatible.
Finally, Macornix SPI NOR entries have been cleaned-up and some SFDP
table fixups for Macronix MX25L3255E have been merged.
Aside from this, there is the usual load of misc improvement, fixes,
and yaml conversion.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmg91NEACgkQJWrqGEe9
VoR8egf+JPTtykQ+Bip9bHStgfpxi0+OKL81PUuPBsbs5C546u5t6ZRhoPsU+KqL
ZTyUk3ys7HcSwZCuiS9V6ea6TNV1FvAVZm+ONpkuPnU60++z8YfVr8ZvtgT0IUXx
COi+5ksdsTFZMyRG+VybRKnYNrTYB7j7CqVL8ifxq1XYWnYdhjy5PH4DgAKnBhGL
523kN2eR85AhvJ4aulsKbcqQQYKvJIQbhjAKklA3yQVarDmoOdiSmndoZlRy+MDu
B9DaRMvRRa/g1nI0stvR9K7FtdSrMYTg4kowR9jPRx0zEZXFFsZbASgcC+3G7HdK
7rLFWrN+G6fitcEjeAnfyV+sKF48LA==
=tW1t
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"A big core MTD change is the introduction of a new class to always
register a master device. This is a problem that has been there
forever: the "master" device was not always present depending on a
number of heuristics such as the presence of fixed partitions and the
absence of a Kconfig symbol to force its presence. This was a problem
for runtime PM operations which might not have the "master" device
available in all situation.
The SPI NAND subsystem has seen the introduction of DTR operations
(the equivalent of DDR transfers), which involved quite a few
preparation patches for clarifying macro names.
In the raw NAND subsystem, the brcmnand driver has been "fixed" for
old legacy SoCs with an update of the ->exec_op() hook, there has been
the introduction of a new controller driver named Loongson-1, and the
Qualcomm driver has received quite a few misc fixes as well as a new
compatible.
Finally, Macornix SPI NOR entries have been cleaned-up and some SFDP
table fixups for Macronix MX25L3255E have been merged.
Aside from this, there is the usual load of misc improvement, fixes,
and yaml conversion"
* tag 'mtd/for-6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (42 commits)
mtd: rawnand: brcmnand: legacy exec_op implementation
mtd: rawnand: sunxi: Add randomizer configuration in sunxi_nfc_hw_ecc_write_chunk
mtd: nand: brcmnand: fix NAND timeout when accessing eMMC
mtd: nand: sunxi: Add randomizer configuration before randomizer enable
mtd: spinand: esmt: fix id code for F50D1G41LB
mtd: rawnand: brcmnand: remove unused parameters
mtd: core: always create master device
mtd: rawnand: loongson1: Fix inconsistent refcounting in ls1x_nand_chip_init()
mtd: rawnand: loongson1: Fix error code in ls1x_nand_dma_transfer()
mtd: rawnand: qcom: Fix read len for onfi param page
mtd: rawnand: qcom: Fix last codeword read in qcom_param_page_type_exec()
mtd: rawnand: qcom: Pass 18 bit offset from NANDc base to BAM base
dt-bindings: mtd: qcom,nandc: Document the SDX75 NAND controller
mtd: bcm47xxnflash: Add error handling for bcm47xxnflash_ops_bcm4706_ctl_cmd()
mtd: rawnand: Use non-hybrid PCI devres API
mtd: nand: ecc-mxic: Fix use of uninitialized variable ret
mtd: spinand: winbond: Add support for W35N02JW and W35N04JW chips
mtd: spinand: winbond: Add octal support
mtd: spinand: winbond: Add support for W35N01JW in single mode
mtd: spinand: winbond: Rename DTR variants
...
equivalent of DDR transfers), which involved quite a few preparation
patches for clarifying macro names.
In the raw NAND subsystem, the brcmnand driver has been "fixed" for old
legacy SoCs with an update of the ->exec_op() hook, there has been the
introduction of a new controller driver named Loongson-1, and the
Qualcomm driver has received quite a few misc fixes as well as a new
compatible.
Aside from this, there is the usual load of misc improvement and fixes.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmg90ysACgkQJWrqGEe9
VoTK8gf/U+28sdthNVHENmeQwgzMdjAaZkEn0qftRVplPUTGSqvkrTBQ2tsyGVpj
V2jJ85WzQ6c+YVRjUsgojX4JClh0tfNrm8ySSu3TOAv98E/sCFttQgyCbELtt6GL
P4/1g/BqHlagi1ouU95AtH3njZX9qXBq9cQGz3ZWX+qeS0p52wPsj1G8iy6syBR+
M6GZI92iINSXJUBlFBXzijDSxqcLWsAg8P2E5dTyL9Ukjcju0+fSQtt1oCp1F50+
zXJHfj3mB+BtBnX6nGhMu3sqY7LaM2NpEq7k6xtvo9ivWZwFAOK+uc31iGvAcKaZ
R1A72QkRE3e0vQZjrX1JKZvXMVXt4Q==
=Uj/O
-----END PGP SIGNATURE-----
Merge tag 'nand/for-6.16' into mtd/next
The SPI NAND subsystem has seen the introduction of DTR operations (the
equivalent of DDR transfers), which involved quite a few preparation
patches for clarifying macro names.
In the raw NAND subsystem, the brcmnand driver has been "fixed" for old
legacy SoCs with an update of the ->exec_op() hook, there has been the
introduction of a new controller driver named Loongson-1, and the
Qualcomm driver has received quite a few misc fixes as well as a new
compatible.
Aside from this, there is the usual load of misc improvement and fixes.
The function sunxi_nfc_hw_ecc_write_chunk() calls the
sunxi_nfc_hw_ecc_write_chunk(), but does not call the configuration
function sunxi_nfc_randomizer_config(). Consequently, the randomization
might not conduct correctly, which will affect the lifespan of NAND flash.
A proper implementation can be found in sunxi_nfc_hw_ecc_write_page_dma().
Add the sunxi_nfc_randomizer_config() to config randomizer.
Fixes: 4be4e03efc ("mtd: nand: sunxi: add randomizer support")
Cc: stable@vger.kernel.org # v4.6
Signed-off-by: Wentao Liang <vulab@iscas.ac.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
When booting a board to NAND and accessing NAND while eMMC
transactions are occurring the NAND will sometimes timeout. This
is due to both NAND and eMMC controller sharing the same data bus
on BCMBCA chips. Fix is to extend NAND timeout to allow eMMC
transactions time to complete.
Signed-off-by: David Regan <dregan@broadcom.com>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In sunxi_nfc_hw_ecc_read_chunk(), the sunxi_nfc_randomizer_enable() is
called without the config of randomizer. A proper implementation can be
found in sunxi_nfc_hw_ecc_read_chunks_dma().
Add sunxi_nfc_randomizer_config() before the start of randomization.
Fixes: 4be4e03efc ("mtd: nand: sunxi: add randomizer support")
Cc: stable@vger.kernel.org # v4.6
Signed-off-by: Wentao Liang <vulab@iscas.ac.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Upon detecting the ID for the ESMT F50D1G41LB chip, the fifth byte
returned is always 0x00 instead of the expected JEDEC continuation code
of 0x7f. This causes detection to fail:
[ 0.304399] spi-nand spi0.0: unknown raw ID c8117f7f00
[ 0.508943] spi-nand: probe of spi0.0 failed with error -524
So let's revert back to the 4 byte ID code for this chip
specifically.
Fixes: 4bd14b2fd8 ("mtd: spinand: esmt: Extend IDs to 5 bytes")
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
last_cmd and last_byte are now unused brcmnand_host members.
last_addr is only written and never read so we can remove it too.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Create master device without partition when
CONFIG_MTD_PARTITIONED_MASTER flag is unset.
This streamlines device tree and allows to anchor
runtime power management on master device in all cases.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The minimum size to fetch the data from device to QPIC buffer
is 512-bytes. If size is less than 512-bytes the data will not be
protected by ECC as per QPIC standard. So while reading onfi parameter
page from NAND device set nandc->buf_count = 512.
Cc: stable@vger.kernel.org
Fixes: 89550beb09 ("mtd: rawnand: qcom: Implement exec_op()")
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Tested-by: Lakshmi Sowjanya D <quic_laksd@quicinc.com>
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
For QPIC V2 onwards there is a separate register to read
last code word "QPIC_NAND_READ_LOCATION_LAST_CW_n".
qcom_param_page_type_exec() is used to read only one code word
If it configures the number of code words to 1 in QPIC_NAND_DEV0_CFG0
register then QPIC controller thinks its reading the last code word,
since we are having separate register to read the last code word,
we have to configure "QPIC_NAND_READ_LOCATION_LAST_CW_n" register
to fetch data from QPIC buffer to system memory.
Without this change page read was failing with timeout error
/ # hexdump -C /dev/mtd1
[ 129.206113] qcom-nandc 1cc8000.nand-controller: failure to read page/oob
hexdump: /dev/mtd1: Connection timed out
This issue only seen on SDX targets since SDX target used QPICv2. But
same working on IPQ targets since IPQ used QPICv1.
Cc: stable@vger.kernel.org
Fixes: 89550beb09 ("mtd: rawnand: qcom: Implement exec_op()")
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Tested-by: Lakshmi Sowjanya D <quic_laksd@quicinc.com>
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The BAM command descriptor provides only 18 bits to specify the BAM
register offset. Additionally, in the BAM command descriptor, the BAM
register offset is supposed to be specified as "(NANDc base - BAM base)
+ reg_off". Since, the BAM controller expecting the value in the form of
"NANDc base - BAM base", so that added a new field 'bam_offset' in the NAND
properties structure and use it while preparing the command descriptor.
Previously, the driver was specifying the NANDc base address in the BAM
command descriptor.
Cc: stable@vger.kernel.org
Fixes: 8d6b6d7e13 ("mtd: nand: qcom: support for command descriptor formation")
Tested-by: Lakshmi Sowjanya D <quic_laksd@quicinc.com>
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Acked-by: Mark Brown <broonie@kernel.org>
Tested-by: Gabor Juhos <j4g8y7@gmail.com> # on IPQ9574
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The function bcm47xxnflash_ops_bcm4706_cmd_ctrl() calls the function
bcm47xxnflash_ops_bcm4706_ctl_cmd(), but does not check its return value.
A proper implementation can be found in bcm47xxnflash_ops_bcm4706_write().
Add error log to the bcm47xxnflash_ops_bcm4706_ctl_cmd() via pr_err()
to prevent silent failure. The error Log funciton 'dev_err' is unsuitable
in this situation for it is hard to get device pointer.
Signed-off-by: Wentao Liang <vulab@iscas.ac.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
denali_pci.c enables a PCI device with pcim_enable_device(). This,
implicitly, switches the function pci_request_regions() into managed
mode, where it becomes a devres function.
The PCI subsystem wants to remove this hybrid nature from its
interfaces. To do so, users of the aforementioned combination of
functions must be ported to non-hybrid functions.
Moreover, since both functions are already managed in this driver, the
calls to pci_release_regions() are unnecessary.
Remove the calls to pci_release_regions().
Replace the call to sometimes-managed pci_request_regions() with one to
the always-managed pcim_request_regions().
Signed-off-by: Philipp Stanner <phasta@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
If ctx->steps is zero, the loop processing ECC steps is skipped,
and the variable ret remains uninitialized. It is later checked
and returned, which leads to undefined behavior and may cause
unpredictable results in user space or kernel crashes.
This scenario can be triggered in edge cases such as misconfigured
geometry, ECC engine misuse, or if ctx->steps is not validated
after initialization.
Initialize ret to zero before the loop to ensure correct and safe
behavior regardless of the ctx->steps value.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 48e6633a9f ("mtd: nand: mxic-ecc: Add Macronix external ECC engine support")
Signed-off-by: Mikhail Arkhipov <m.arhipov@rosa.ru>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
These chips support single SPI, octal SPI and octal DDR SPI.
For now, only the SDR protocols are supported.
Tested with the W35N02JW variant, but the 04 one just has twice more
dies and is described in the same datasheet, so we can reasonably expect
that it will behave identically.
Acked-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Describe the octal "read from cache" (1S_1S_8S, 1S_8S_8S and
1S_1D_8D_OP) and "program load" (1S_1S_8S and 1S_8S_8S) operations
supported by the W35N01JW chip.
There is no observable improvement between the two octal SDR modes,
which anyway offered a great read speed improvement compared to single
mode.
flash_speed test results ran on the TI AM62A7 LP SK using a 25MHz SPI bus:
* Single mode:
eraseblock read speed is 2346 KiB/s
page read speed is 2342 KiB/s
eraseblock write speed is 2028 KiB/s
page write speed is 2028 KiB/s
* Octal modes:
eraseblock read speed is 10801 KiB/s
page read speed is 10711 KiB/s
eraseblock write speed is 7335 KiB/s
page write speed is 7293 KiB/s
However, testing on the cadence qspi controller driver did not allow
mixed modes (where SDR and DTR cycles are mixed in the same operation),
thus 1S-1D-8D mode could not be tested and is provided for reference (it
is anyway skipped on platforms not supporting this). It did not allow
easy "update cache" tests either, so these macros are untested and given
as-is.
Acked-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add support for the W35N series by describing the smaller (single die)
chip. It has 1b/512B ECC support and its own OOB layout.
Acked-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
So far all the chips supported in the driver apparently have support for
the same kind of operation (typically, single, dual and quad). The
future introduction of W35N chips will change that as these chips only
support single and octal modes. Let's rename the variants accordingly to
make these future additions more understandable.
Acked-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
SPI operations have been initially described through macros implicitly
implying the use of a single SPI SDR bus. Macros for supporting dual and
quad I/O transfers have been added on top, generally inspired by vendor
naming, followed by DTR operations. Soon we might see octal
and even octal DTR operations as well (including the opcode byte).
Let's clarify what the macro really means by describing the expected bus
topology in the (quad) program load macro name.
While at modifying it, better add the missing_ OP suffix to align with
all the other macros of the same kind.
Acked-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
SPI operations have been initially described through macros implicitly
implying the use of a single SPI SDR bus. Macros for supporting dual and
quad I/O transfers have been added on top, generally inspired by vendor
naming, followed by DTR operations. Soon we might see octal
and even octal DTR operations as well (including the opcode byte).
Let's clarify what the macro really means by describing the expected bus
topology in the (single) program load macro name.
While at modifying it, better add the missing_ OP suffix to align with
all the other macros of the same kind.
Acked-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
SPI operations have been initially described through macros implicitly
implying the use of a single SPI SDR bus. Macros for supporting dual and
quad I/O transfers have been added on top, generally inspired by vendor
naming, followed by DTR operations. Soon we might see octal
and even octal DTR operations as well (including the opcode byte).
Let's clarify what the macro really means by describing the expected bus
topology in the program execution macro name.
Acked-by: Tudor Ambarus <tudor.ambarus@linaro.org>
[Miquel: Fixed conflicts with -next by updating esmt and micron drivers]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
SPI operations have been initially described through macros implicitly
implying the use of a single SPI SDR bus. Macros for supporting dual and
quad I/O transfers have been added on top, generally inspired by vendor
naming, followed by DTR operations. Soon we might see octal
and even octal DTR operations as well (including the opcode byte).
Let's clarify what the macro really mean by describing the expected bus
topology in the (quad IO) read from cache macro names.
Acked-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
SPI operations have been initially described through macros implicitly
implying the use of a single SPI SDR bus. Macros for supporting dual and
quad I/O transfers have been added on top, generally inspired by vendor
naming, followed by DTR operations. Soon we might see octal
and even octal DTR operations as well (including the opcode byte).
Let's clarify what the macro really mean by describing the expected bus
topology in the (quad output) read from cache macro names.
Acked-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
SPI operations have been initially described through macros implicitly
implying the use of a single SPI SDR bus. Macros for supporting dual and
quad I/O transfers have been added on top, generally inspired by vendor
naming, followed by DTR operations. Soon we might see octal
and even octal DTR operations as well (including the opcode byte).
Let's clarify what the macro really mean by describing the expected bus
topology in the (dual IO) read from cache macro names. While at
modifying them, better reordering the macros to group them all by bus
topology which now feels more intuitive.
Acked-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
SPI operations have been initially described through macros implicitly
implying the use of a single SPI SDR bus. Macros for supporting dual and
quad I/O transfers have been added on top, generally inspired by vendor
naming, followed by DTR operations. Soon we might see octal
and even octal DTR operations as well (including the opcode byte).
Let's clarify what the macro really mean by describing the expected bus
topology in the (dual output) read from cache macro names.
Acked-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
SPI operations have been initially described through macros implicitly
implying the use of a single SPI SDR bus. Macros for supporting dual and
quad I/O transfers have been added on top, generally inspired by vendor
naming, followed by DTR operations. Soon we might see octal
and even octal DTR operations as well (including the opcode byte).
Let's clarify what the macro really mean by describing the expected bus
topology in the (single) read from cache macro names.
Acked-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
SPI operations have been initially described through macros implicitly
implying the use of a single SPI SDR bus. Macros for supporting dual and
quad I/O transfers have been added on top, generally inspired by vendor
naming, followed by DTR operations. Soon we might see octal
and even octal DTR operations as well (including the opcode byte).
Let's clarify what the macro really means by describing the expected bus
topology in the page read macro name.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
SPI operations have been initially described through macros implicitly
implying the use of a single SPI SDR bus. Macros for supporting dual and
quad I/O transfers have been added on top, generally inspired by vendor
naming, followed by DTR operations. Soon we might see octal
and even octal DTR operations as well (including the opcode byte).
Let's clarify what the macro really means by describing the expected bus
topology in the erase macro name.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
SPI operations have been initially described through macros implicitly
implying the use of a single SPI SDR bus. Macros for supporting dual and
quad I/O transfers have been added on top, generally inspired by vendor
naming, followed by DTR operations. Soon we might see octal
and even octal DTR operations as well (including the opcode byte).
Let's clarify what the macro really mean by describing the expected bus
topology in the get/set feature macro names.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
[Miquel: Fixed conflicts with -next by updating macronix driver]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
SPI operations have been initially described through macros implicitly
implying the use of a single SPI SDR bus. Macros for supporting dual and
quad I/O transfers have been added on top, generally inspired by vendor
naming, followed by DTR operations. Soon we might see octal
and even octal DTR operations as well (including the opcode byte).
Let's clarify what the macro really means by describing the expected bus
topology in the read ID macro name.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
SPI operations have been initially described through macros implicitly
implying the use of a single SPI SDR bus. Macros for supporting dual and
quad I/O transfers have been added on top, generally inspired by vendor
naming, followed by DTR operations. Soon we might see octal
and even octal DTR operations as well (including the opcode byte).
Let's clarify what the macro really means by describing the expected bus
topology in the write enable/disable macro names.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
[Miquel: Fixed conflicts with -next by updating esmt and micron drivers]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Enabling the compile test should not cause automatic enabling of all
drivers, but only allow to choose to compile them.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
SPI operations have been initially described through macros implicitly
implying the use of a single SPI SDR bus. Macros for supporting dual and
quad I/O transfers have been added on top, generally inspired by vendor
vendor naming, followed by DTR operations. Soon we might see octal
and even octal DTR operations as well (including the opcode byte).
Let's clarify what the macro really means by describing the expected bus
topology in the reset macro name.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
SFDP of MX25L3255E is JESD216, which does not include the Quad
Enable bit Requirement in BFPT. As a result, during BFPT parsing,
the quad_enable method is not set to spi_nor_sr1_bit6_quad_enable.
Therefore, it is necessary to correct this setting by late_init.
In addition, MX25L3255E also supports 1-4-4 page program in 3-byte
address mode. However, since the 3-byte address 1-4-4 page program
is not defined in SFDP, it needs to be configured in late_init.
Signed-off-by: Cheng Ming Lin <chengminglin@mxic.com.tw>
Acked-by: Pratyush Yadav <pratyush@kernel.org>
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
[pratyush@kernel.org: move params declaration to top, and use it everywhere]
Link: https://lore.kernel.org/r/20250407075400.1113177-4-linchengming884@gmail.com
To clean up the code and reduce duplication, this entry is removed.
Signed-off-by: Cheng Ming Lin <chengminglin@mxic.com.tw>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20250407075400.1113177-3-linchengming884@gmail.com
Many flash devices share the same ID but have different part numbers.
To avoid confusion, the part number field is removed.
Additionally, since SFDP already provides size information and
functionality covered by no_sfdp_flags, these fields are also removed.
Furthermore, when 4-byte address instruction table is available,
the SPI_NOR_4B_OPCODES flag is no longer needed and is removed.
Signed-off-by: Cheng Ming Lin <chengminglin@mxic.com.tw>
Acked-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20250407075400.1113177-2-linchengming884@gmail.com
In r852_ready(), the dev get from r852_get_dev() need to be checked.
An unstable device should not be ready. A proper implementation can
be found in r852_read_byte(). Add a status check and return 0 when it is
unstable.
Fixes: 50a487e771 ("mtd: rawnand: Pass a nand_chip object to chip->dev_ready()")
Cc: stable@vger.kernel.org # v4.20+
Signed-off-by: Wentao Liang <vulab@iscas.ac.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In INFTL_findwriteunit(), the return value of inftl_read_oob()
need to be checked. A proper implementation can be
found in INFTL_deleteblock(). The status will be set as
SECTOR_IGNORE to break from the while-loop correctly
if the inftl_read_oob() fails.
Fixes: 8593fbc68b ("[MTD] Rework the out of band handling completely")
Cc: stable@vger.kernel.org # v2.6+
Signed-off-by: Wentao Liang <vulab@iscas.ac.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
If CONFIG_SPI_QPIC_SNAND=m, but CONFIG_MTD_NAND_QCOM=n:
ERROR: modpost: "qcom_nandc_unalloc" [drivers/spi/spi-qpic-snand.ko] undefined!
...
Fix this by dropping the explicit test for a built-in
CONFIG_SPI_QPIC_SNAND completely. Kbuild handles multiple and mixed
obj-y/obj-m rules for the same object file fine.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202503280759.XhwLcV7m-lkp@intel.com/
Fixes: 7304d19090 ("spi: spi-qpic: add driver for QCOM SPI NAND flash Interface")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
timer_delete[_sync]() replaces del_timer[_sync](). Convert the whole tree
over and remove the historical wrapper inlines.
Conversion was done with coccinelle plus manual fixups where necessary.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The atmel,dataflash binding has been converted to yaml and the physmap
one constrained. Some logs are improved, error path are getting reworked
a bit, few patches target the use of str_enabled_disabled().
* Raw NAND changes:
i.MX8 and i.MX31 now have their own compatible, the Qcom driver got
cleaned, the Broadcom driver got fixed.
* SPI NAND changes:
Two main features have been added:
- OTP support has been brought, and ESMT and Micron manufacturer drivers
implement it.
- Read retry, and Macronix manufacturer driver implement it.
* SPI NOR changes:
Adding support for few flashes. Few cleanup patches for the core
driver, where we touched the headers inclusion list and we start using
the scope based mutex cleanup helpers.
There is as well a bunch of minor improvements and fixes in drivers and
bindings.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmfkMTQACgkQJWrqGEe9
VoS+Fgf/apT4C5115f4EolKAcato3QpJ+J1+S0Oy6yYSKQVwKNa4NkdBIeKXfQLc
rjNdsoE9RmibCKViX3D3rjlMnynbkIr4F3YHbgP4lz7y2TQUVA7Dy0sp2RX+9M3G
+a5u6lfUyGA/uzJPJUESaPpjLWLg5uTRcduD8hGVid9D+/KFYWNF0EsufobT8JmT
X/R+aVS58W0uqLEJtiaINsD6D3f8ukMZCNgsvuAUINSUNUrX61pVQZwQAZ4eCCNa
W+YaLdsMtrwRBdoRGXfrElHEvnufglYocUo+9h8EOVMQ84rfNH363Nu+1WxTVGDj
GLB5O9knQFy7DR0M4gYBAqqji41nTg==
=O/Ud
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-6.15' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd updates from Miquel Raynal:
"MTD changes:
- The atmel,dataflash binding has been converted to yaml and the
physmap one constrained. Some logs are improved, error path are
getting reworked a bit, few patches target the use of
str_enabled_disabled().
Raw NAND changes:
- i.MX8 and i.MX31 now have their own compatible, the Qcom driver got
cleaned, the Broadcom driver got fixed.
SPI NAND changes:
- OTP support has been brought, and ESMT and Micron manufacturer
drivers implement it.
- Read retry, and Macronix manufacturer driver implement it.
SPI NOR changes:
- Adding support for few flashes. Few cleanup patches for the core
driver, where we touched the headers inclusion list and we start
using the scope based mutex cleanup helpers.
There is also a bunch of minor improvements and fixes in drivers
and bindings"
* tag 'mtd/for-6.15' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (34 commits)
dt-bindings: mtd: atmel,dataflash: convert txt to yaml
mtd: mchp48l640: Use str_enable_disable() in mchp48l640_write_prepare()
mtd: rawnand: gpmi: Use str_enabled_disabled() in gpmi_nand_attach_chip()
mtd: mtdpart: Do not supply NULL to printf()
dt-bindings: mtd: gpmi-nand: Add compatible string for i.MX8 chips
mtd: nand: Fix a kdoc comment
mtd: spinand: Improve spinand_info macros style
mtd: spi-nor: drop unused <linux/of_platform.h>
mtd: spi-nor: explicitly include <linux/of.h>
mtd: spi-nor: explicitly include <linux/math64.h>
mtd: spi-nor: macronix: add support for mx66{l2, u1}g45g
mtd: spi-nor: macronix: Add post_sfdp fixups for Quad Input Page Program
mtd: Fix error handling in mtd_device_parse_register() error path
mtd: capture device name setting failure when adding mtd
mtd: Add check for devm_kcalloc()
mtd: Replace kcalloc() with devm_kcalloc()
dt-bindings: mtd: physmap: Ensure all properties are defined
mtd: rawnand: brcmnand: fix PM resume warning
dt-bindings: mtd: mxc-nand: Document fsl,imx31-nand
mtd: spinand: macronix: Add support for read retry
...
i.MX8 and i.MX31 now have their own compatible, the Qcom driver got
cleaned, the Broadcom driver got fixed.
* SPI NAND changes:
Two main features have been added:
- OTP support has been brought, and ESMT and Micron manufacturer drivers
implement it.
- Read retry, and Macronix manufacturer driver implement it.
There is as well a bunch of minor improvements and fixes in drivers and
bindings.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmfkLyUACgkQJWrqGEe9
VoTj/gf/UFLUlbCTTLpiKItXTTywW7EEe/8ZvVoki/D6gzKrjfMnVzYjxpLqYCnc
Qps6RtHPX8Xkq2f7FMFCxu6t49PLFjvo8JIdEC7Q1Bxf3JLAPtQXIXZfl+frtNnc
MqctdU4BU9up8u1mCajjzSWtaCeU3YBwNtH9fPMS65b5dfg1vfXr7oA/NqfMg3ql
b4dMYHXzPHk6TP59q3yaTqkFf92yXzgEUjM651uoAIzafVSpVHyOZriDit8A/A3f
lBM0+SEhEPBBhMvWf0FgzlqWidmCE+LZPTypdkgVamvqYPh/KYFUs14UDmJd/M1t
TwXf+Q5c6mnGfmiVVvfM1icp0Lyr+Q==
=W0/k
-----END PGP SIGNATURE-----
Merge tag 'nand/for-6.15' into mtd/next
* Raw NAND changes:
i.MX8 and i.MX31 now have their own compatible, the Qcom driver got
cleaned, the Broadcom driver got fixed.
* SPI NAND changes:
Two main features have been added:
- OTP support has been brought, and ESMT and Micron manufacturer drivers
implement it.
- Read retry, and Macronix manufacturer driver implement it.
There is as well a bunch of minor improvements and fixes in drivers and
bindings.
driver, where we touched the headers inclusion list and we start using
the scope based mutex cleanup helpers.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEHUIqys8OyG1eHf7fS1VPR6WNFOkFAmfZD0wACgkQS1VPR6WN
FOn+RAf+MnyaYWP20nCRoI8Amkemqxzp6oOLQWT6TPSRACyz90V2NGJqSolq2eUE
0pYpjAYmksFIqjTTgR90m0/KBh/+xuGzVQT2Ej2/UEuuE92Y5ZcXk6rUy0TSKAoS
ZE5MvHs7n9TYr1yXbh0Ow6ITkQR3IS1DgII90XuGBdRoZrWnfWCt/tYzacFJ8F37
2ENUKggLacldAIWguCVyamq8WOFFstxXg3d8oHNR/uUHs9qB3n/5vgnjLvKFIkqc
adejnSFR+LCwXOqpgbs9BuI3D+E70Hh+cvAcw1y+jPRHckJRYGCKiemZO2GFBkmi
iMDn/avxf7WEIYlgcwC0TpxnFRtqxA==
=6zFA
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-6.15' into mtd/next
SPI NOR adds support for few flashes. Few cleanup patches for the core
driver, where we touched the headers inclusion list and we start using
the scope based mutex cleanup helpers.
GCC compiler is not happy about NULL being supplied as printf() parameter:
drivers/mtd/mtdpart.c:693:34: error: ‘%s’ directive argument is null [-Werror=format-overflow=]
Move the code after the parser test for NULL, and drop the ternary completely.
The user can deduct this since when it's not NULL two messages will be printed.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's assume all these macros should not have a trailing comma, this way
the caller can use a more formal and usual C writing style, as reflected
in the Macronix driver.
Acked-by: Pratyush Yadav <pratyush@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The core driver is using of_property_read_bool() and relies on implicit
inclusion of <linux/of.h>, which comes from <linux/mtd/mtd.h>.
It is good practice to directly include all headers used, it avoids
implicit dependencies and spurious breakage if someone rearranges
headers and causes the implicit include to vanish.
Include the missing header.
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20250307-spi-nor-headers-cleanup-v1-1-c186a9511c1e@linaro.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
request_queue param is no longer used by blk_rq_map_sg and
__blk_rq_map_sg. Remove it.
Signed-off-by: Anuj Gupta <anuj20.g@samsung.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20250313035322.243239-1-anuj20.g@samsung.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
swp and otp drivers use div_u64 and div64_u64 and rely on implicit
inclusion of <linux/math64.h>.
It is good practice to directly include all headers used, it avoids
implicit dependencies and spurious breakage if someone rearranges
headers and causes the implicit include to vanish.
Include the missing header.
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20250223-snor-math64-v2-1-6f0313eea331@linaro.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Due to incorrect values in the 4-BAIT table for these two flash IDs,
it is necessary to add these two flash IDs with fixups.
Signed-off-by: Cheng Ming Lin <chengminglin@mxic.com.tw>
Link: https://lore.kernel.org/r/20250211063028.382169-3-linchengming884@gmail.com
[ta: update commit subject]
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Although certain Macronix NOR flash support the Quad Input Page Program
feature, the corresponding information in the 4-byte Address Instruction
Table of these flash is not properly filled. As a result, this feature
cannot be enabled as expected.
To address this issue, a post_sfdp fixups implementation is required to
correct the missing information.
Signed-off-by: Cheng Ming Lin <chengminglin@mxic.com.tw>
Link: https://lore.kernel.org/r/20250211063028.382169-2-linchengming884@gmail.com
[ta: fix alignment to match open parenthesis]
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Check and log del_mtd_device() failures. Print an error message
with pr_err() to prevent silent failures, but preserve the original
error code instead of propagating the secondary error since
del_mtd_device() is already in an error handling path.
Signed-off-by: Wentao Liang <vulab@iscas.ac.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add a check for devm_kcalloc() to ensure successful allocation.
Fixes: 78c08247b9 ("mtd: Support kmsg dumper based on pstore/blk")
Cc: stable@vger.kernel.org # v5.10+
Signed-off-by: Jiasheng Jiang <jiashengjiangcool@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Replace kcalloc() with devm_kcalloc() to prevent memory leaks in case of
errors.
Fixes: 78c08247b9 ("mtd: Support kmsg dumper based on pstore/blk")
Cc: stable@vger.kernel.org # v5.10+
Signed-off-by: Jiasheng Jiang <jiashengjiangcool@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add read retry support.
The Special Read for Data Recovery operation is enabled by
Set Feature function.
There are 5 modes for the user to recover the lost data.
Signed-off-by: Cheng Ming Lin <chengminglin@mxic.com.tw>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
When the host ECC fails to correct the data error of NAND device,
there's a special read for data recovery method which can be setup
by the host for the next read. There are several retry levels that
can be attempted until the lost data is recovered or definitely
assumed lost.
Signed-off-by: Cheng Ming Lin <chengminglin@mxic.com.tw>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This driver implements support for the SPI-NAND mode of QCOM NAND Flash
Interface as a SPI-MEM controller with pipelined ECC capability.
Co-developed-by: Sricharan Ramabadhran <quic_srichara@quicinc.com>
Signed-off-by: Sricharan Ramabadhran <quic_srichara@quicinc.com>
Co-developed-by: Varadarajan Narayanan <quic_varada@quicinc.com>
Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com>
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Link: https://patch.msgid.link/20250224111414.2809669-3-quic_mdalam@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 18bcb4aa54 ("mtd: spi-nor: sst: Factor out common write
operation to `sst_nor_write_data()`") introduced a bug where only one
byte of data is written, regardless of the number of bytes requested.
This causes the driver to use the incorrect write size for flashes using
the SST byte programming, and to spit out a warning.
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQQTlUWNzXGEo3bFmyIR4drqP028CQUCZ7NEiBQccHJhdHl1c2hA
a2VybmVsLm9yZwAKCRAR4drqP028CTVnAP9krBOLfmlYO94PntaDscgjcehnxbuF
PEQby8/KlEnX0gEA5K73/0oQIZUnHQ98E6ntAtKoYD5zGNAJaYDpw+66CAU=
=5xea
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/fixes-for-6.14-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux into mtd/fixes
Fix writes on SST flashes
Commit 18bcb4aa54 ("mtd: spi-nor: sst: Factor out common write
operation to `sst_nor_write_data()`") introduced a bug where only one
byte of data is written, regardless of the number of bytes requested.
This causes the driver to use the incorrect write size for flashes using
the SST byte programming, and to spit out a warning.
# -----BEGIN PGP SIGNATURE-----
#
# iIoEABYIADIWIQQTlUWNzXGEo3bFmyIR4drqP028CQUCZ7NEiBQccHJhdHl1c2hA
# a2VybmVsLm9yZwAKCRAR4drqP028CTVnAP9krBOLfmlYO94PntaDscgjcehnxbuF
# PEQby8/KlEnX0gEA5K73/0oQIZUnHQ98E6ntAtKoYD5zGNAJaYDpw+66CAU=
# =5xea
# -----END PGP SIGNATURE-----
# gpg: Signature made Mon 17 Feb 2025 03:15:36 PM CET
# gpg: using EDDSA key 1395458DCD7184A376C59B2211E1DAEA3F4DBC09
# gpg: issuer "pratyush@kernel.org"
# gpg: Good signature from "Pratyush Yadav <p.yadav@ti.com>" [expired]
# gpg: aka "Pratyush Yadav <me@yadavpratyush.com>" [expired]
# gpg: issuer "pratyush@kernel.org" does not match any User ID
# gpg: WARNING: The key's User ID is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 805C 3923 2FBE 108C 49E1 663C F650 3556 C11B 1CCD
# Subkey fingerprint: 1395 458D CD71 84A3 76C5 9B22 11E1 DAEA 3F4D BC09
Sorting headers alphabetically helps locating duplicates,
and makes it easier to figure out where to insert new headers.
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20250211-spi-nor-guard-mutex-v1-1-05ed77a484d9@linaro.org
With some research in some obscure old QSDK, it was possible to find the
MASK of the last register there were still set with raw shift and
convert them to FIELD_PREP API.
This is only a cleanup and modernize the code a bit and doesn't make
any behaviour change.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Fix broken config in qcom_param_page_type_exec caused by copy-paste error
from commit 0c08080fd7 ("mtd: rawnand: qcom: use FIELD_PREP and GENMASK")
In qcom_param_page_type_exec the value needs to be set to
nandc->regs->cfg0 instead of host->cfg0. This wrong configuration caused
the Qcom NANDC driver to malfunction on any device that makes use of it
(IPQ806x, IPQ40xx, IPQ807x, IPQ60xx) with the following error:
[ 0.885369] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xaa
[ 0.885909] nand: Micron NAND 256MiB 1,8V 8-bit
[ 0.892499] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 0.896823] nand: ECC (step, strength) = (512, 8) does not fit in OOB
[ 0.896836] qcom-nandc 79b0000.nand-controller: No valid ECC settings possible
[ 0.910996] bam-dma-engine 7984000.dma-controller: Cannot free busy channel
[ 0.918070] qcom-nandc: probe of 79b0000.nand-controller failed with error -28
Restore original configuration fix the problem and makes the driver work
again.
Also restore the wrongly dropped cpu_to_le32 to correctly support BE
systems.
Cc: stable@vger.kernel.org
Fixes: 0c08080fd7 ("mtd: rawnand: qcom: use FIELD_PREP and GENMASK")
Tested-by: Robert Marko <robimarko@gmail.com> # IPQ8074 and IPQ6018
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
dma_map_single is using physical/bus device (DMA) but dma_unmap_single
is using framework device(NAND controller), which is incorrect.
Fixed dma_unmap_single to use correct physical/bus device.
Fixes: ec4ba01e89 ("mtd: rawnand: Add new Cadence NAND driver to MTD subsystem")
Cc: stable@vger.kernel.org
Signed-off-by: Niravkumar L Rabara <niravkumar.l.rabara@intel.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Remap the slave DMA I/O resources to enhance driver portability.
Using a physical address causes DMA translation failure when the
ARM SMMU is enabled.
Fixes: ec4ba01e89 ("mtd: rawnand: Add new Cadence NAND driver to MTD subsystem")
Cc: stable@vger.kernel.org
Signed-off-by: Niravkumar L Rabara <niravkumar.l.rabara@intel.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Replace dma_request_channel() with dma_request_chan_by_mask() and use
helper functions to return proper error code instead of fixed -EBUSY.
Fixes: ec4ba01e89 ("mtd: rawnand: Add new Cadence NAND driver to MTD subsystem")
Cc: stable@vger.kernel.org
Signed-off-by: Niravkumar L Rabara <niravkumar.l.rabara@intel.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Support for OTP area access on ESMT F50L1G41LB and F50D1G41LB chips.
Signed-off-by: Martin Kurbanov <mmkurbanov@salutedevices.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Support for OTP area access on Micron MT29F2G01ABAGD chip.
Signed-off-by: Martin Kurbanov <mmkurbanov@salutedevices.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The global functions spinand_otp_read() and spinand_otp_write() have
been introduced. Since most SPI-NAND flashes read/write OTP in the same
way, let's define global functions to avoid code duplication.
Signed-off-by: Martin Kurbanov <mmkurbanov@salutedevices.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Change the functions spinand_wait() and spinand_otp_page_size() from
static to global so that SPI NAND flash drivers don't duplicate it.
Signed-off-by: Martin Kurbanov <mmkurbanov@salutedevices.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The MTD subsystem already supports accessing two OTP areas: user and
factory. User areas can be written by the user.
This patch provides the SPINAND_FACT_OTP_INFO and SPINAND_USER_OTP_INFO
macros to add parameters to spinand_info.
To implement OTP operations, the client (flash driver) is provided with
callbacks for user area:
.read(), .write(), .info(), .lock(), .erase();
and for factory area:
.read(), .info();
Signed-off-by: Martin Kurbanov <mmkurbanov@salutedevices.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Change these functions from static to global so that to use them later
in OTP operations. Since reading OTP pages is no different from reading
pages from the main area.
Signed-off-by: Martin Kurbanov <mmkurbanov@salutedevices.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add support for Winbond w25q01jv spi-nor chip.
This chip is internally made of two dies with linear addressing
capabilities to make it transparent to the user that two dies were
used. There is one drawback however, the read status operation is racy
as the status bit only gives the active die status and not the status of
the other die. For commands affecting the two dies, it means if another
command is sent too fast after the first die has returned a valid status
(deviation can be up to 200us), the chip will get corrupted/in an
unstable state.
This chip hence requires a better status register read. There are three
solutions here:
1- If we assume that the most common situation producing this problem is
status register writes, maybe we could change the "non-volatile"
status register write commands to become "volatile" status register
writes. In practice, what takes time is the write operation of the bits
themselves, and not the activation of the feature in the internal
circuitry. Enabling "volatile" status register writes would make the
writes nearly instant.
This approach, besides probably being the less impacting one, could
overlook other possible actions where both dies can be used at the same
time like a chip erase (or any erase over die boundaries in general).
2- Wait about 200us after getting a first status ready feedback. This
200us is about the maximum possible deviation between dies and would
cover all cases.
3- We iterate manually over all internal dies (which takes about 30us
per die) until all are ready. This approach will always be faster than
a blind delay which represents the maximum deviation, while also being
totally safe.
This third approach has been adopted. A flash-specific hook for the
status register read had to be implemented. Testing with the flash_speed
benchmark shown no difference with the existing performances (using the
regular status read core function). In practice there are difference in
the experimental results below, but they are part of the natural
deviation of the benchmark:
> Without the fixup
$ flash_speed /dev/mtd0 -c100 -d
eraseblock write speed is 442 KiB/s
eraseblock read speed is 1606 KiB/s
page write speed is 439 KiB/s
page read speed is 1520 KiB/s
2 page write speed is 441 KiB/s
2 page read speed is 1562 KiB/s
erase speed is 68 KiB/s
> With the fixup
$ flash_speed /dev/mtd0 -c100 -d
eraseblock write speed is 428 KiB/s
eraseblock read speed is 1626 KiB/s
page write speed is 426 KiB/s
page read speed is 1538 KiB/s
2 page write speed is 426 KiB/s
2 page read speed is 1574 KiB/s
erase speed is 66 KiB/s
However, the fixup, whatever which one we pick, must be applied on
multi-die chips, which hence must be properly flagged. The SFDP tables
implemented give a lot of information but the die details are part of an
optional table that is not implemented, hence we use a post parsing
fixup hook to set the params->n_dice value manually.
Link: https://www.winbond.com/resource-files/W25Q01JV%20SPI%20RevE%2003042024%20Plus.pdf
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20250110-winbond-6-12-rc1-nor-volatile-bit-v3-1-735363f8cc7d@bootlin.com
-----BEGIN PGP SIGNATURE-----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=molg
-----END PGP SIGNATURE-----
Merge tag 'block-6.14-20250131' of git://git.kernel.dk/linux
Pull more block updates from Jens Axboe:
- MD pull request via Song:
- Fix a md-cluster regression introduced
- More sysfs race fixes
- Mark anything inside queue freezing as not being able to do IO for
memory allocations
- Fix for a regression introduced in loop in this merge window
- Fix for a regression in queue mapping setups introduced in this merge
window
- Fix for the block dio fops attempting an iov_iter revert upton
getting -EIOCBQUEUED on the read side. This one is going to stable as
well
* tag 'block-6.14-20250131' of git://git.kernel.dk/linux:
block: force noio scope in blk_mq_freeze_queue
block: fix nr_hw_queue update racing with disk addition/removal
block: get rid of request queue ->sysfs_dir_lock
loop: don't clear LO_FLAGS_PARTSCAN on LOOP_SET_STATUS{,64}
md/md-bitmap: Synchronize bitmap_get_stats() with bitmap lifetime
blk-mq: create correct map for fallback case
block: don't revert iter for -EIOCBQUEUED
When block drivers or the core block code perform allocations with a
frozen queue, this could try to recurse into the block device to
reclaim memory and deadlock. Thus all allocations done by a process
that froze a queue need to be done without __GFP_IO and __GFP_FS.
Instead of tying to track all of them down, force a noio scope as
part of freezing the queue.
Note that nvme is a bit of a mess here due to the non-owner freezes,
and they will be addressed separately.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20250131120352.1315351-2-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
UBI:
- New interface to dump detailed erase counters
- Fixes around wear-leveling
UBIFS:
- Minor cleanups
- Fix for TNC dumping code
-----BEGIN PGP SIGNATURE-----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=bgVN
-----END PGP SIGNATURE-----
Merge tag 'ubifs-for-linus-6.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs
Pull UBI and UBIFS updates from Richard Weinberger:
"UBI:
- New interface to dump detailed erase counters
- Fixes around wear-leveling
UBIFS:
- Minor cleanups
- Fix for TNC dumping code"
* tag 'ubifs-for-linus-6.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs:
ubi: ubi_get_ec_info: Fix compiling error 'cast specifies array type'
ubi: Implement ioctl for detailed erase counters
ubi: Expose interface for detailed erase counters
ubifs: skip dumping tnc tree when zroot is null
ubi: Revert "ubi: wl: Close down wear-leveling before nand is suspended"
ubifs: ubifs_dump_leb: remove return from end of void function
ubifs: dump_lpt_leb: remove return at end of void function
ubi: Add a check for ubi_num
There's been no major core change, and a bunch of driver related
improvements, amongst them the conversion to of_property_present() for
non-boolean properties, the addition of the support for Fujitsu
MB85RS128TY FRAM, a couple of improvements to the phram driver and the
usual load of misc changes.
* Raw NAND changes
A new controller driver, from Nuvoton, has been merged.
Bastien Curutchet has contributed a series improving the Davinci
controller driver, both on the organization of the code, but also on the
performance side. The binding has also been converted to yaml, received
a new OOB layout and now supports on-die ECC engines.
The Qualcomm controller driver has been deeply cleaned to extract some
parts of the code into a shared file with the Qualcomm SPI memory
controller.
Aside from these main changes, the Cadence binding has been converted to
yaml, the brcmnand controller driver has received a small fix, otherwise
some more minor changes have also made their way in.
* SPI NAND changes
The SPI NAND subsystem has seen a great improvement, with the advent of
DTR operations (DDR operations, which may be extended to the address
cycles). The first vendor driver to benefit from these improvements is
the Winbond driver.
A new manufacturer driver is added SkyHigh, with a new constraint for
the core, it is impossible to disable the on-die ECC engine.
A Foresee device is also now supported.
* SPI NOR changes
Several flash entries have been added: Atmel AT25SF321, Spansion
S28HL256T and S28HL02GT.
Support for vcc-supply regulators and their DT bindings has been added.
The mx25u25635f entry has been dropped. The flash shares its ID with
mx25u25645g and both parts have an SFDP table. Removing their entry lets
them be driven by the generic SFDP-based driver.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmeTZO0ACgkQJWrqGEe9
VoSW1Qf/f96ejqjzTenBHYKOdSqm6aoML17po1xAUubIViub6LJQBHHrj69qvCvj
A4LrqQBPrnH1Escw79QEdwtTrefqra7CHnR1mMrhgF9SCS90762tt+MZ3+GDawBD
CU/Zw86+FrFyH1wRZg6RFT+FEGHBIExi7FqpypBLARdYrGt8ZpNDhJuPHizhvyco
Whd2WCoQEYxRsPQr+tcAuTtymCRSrNQ+IalVoTfm7p0QHS3OGfJWHHS92FPwTs/H
p2TvkEY/HD4pSelseJhG7nWA+CgfxyTg0pzISi2Ctr3qH76AHTDRZBm1xBKY/NiY
ZfC1YJ3cAjyN+VfL897DopAqmZK+3g==
=mk21
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-6.14' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"MTD changes:
- There's been no major core change, just a bunch of driver related
improvements.
Amongst them the conversion to of_property_present() for
non-boolean properties, the addition of the support for Fujitsu
MB85RS128TY FRAM, a couple of improvements to the phram driver and
the usual load of misc changes.
Raw NAND changes:
- A new controller driver, from Nuvoton, has been merged
- Bastien Curutchet has contributed a series improving the Davinci
controller driver, both on the organization of the code, but also
on the performance side. The binding has also been converted to
yaml, received a new OOB layout and now supports on-die ECC engines
- The Qualcomm controller driver has been deeply cleaned to extract
some parts of the code into a shared file with the Qualcomm SPI
memory controller
- Aside from these main changes, the Cadence binding has been
converted to yaml, the brcmnand controller driver has received a
small fix, otherwise some more minor changes have also made their
way in
SPI NAND changes:
- The SPI NAND subsystem has seen a great improvement, with the
advent of DTR operations (DDR operations, which may be extended to
the address cycles). The first vendor driver to benefit from these
improvements is the Winbond driver
- A new manufacturer driver is added SkyHigh, with a new constraint
for the core, it is impossible to disable the on-die ECC engine
- A Foresee device is also now supported
SPI NOR changes:
- Several flash entries have been added: Atmel AT25SF321, Spansion
S28HL256T and S28HL02GT
- Support for vcc-supply regulators and their DT bindings has been
added
- The mx25u25635f entry has been dropped. The flash shares its ID
with mx25u25645g and both parts have an SFDP table. Removing their
entry lets them be driven by the generic SFDP-based driver"
* tag 'mtd/for-6.14' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (47 commits)
mtd: spinand: skyhigh: Align with recent read from cache variant changes
mtd: spinand: winbond: Add support for DTR operations
mtd: spinand: winbond: Add comment about naming
mtd: spinand: winbond: Update the *JW chip definitions
mtd: spinand: Add support for read DTR operations
mtd: spinand: Enhance the logic when picking a variant
mtd: spinand: Add an optional frequency to read from cache macros
mtd: spinand: Create distinct fast and slow read from cache variants
mtd: hyperbus: Use of_property_present() for non-boolean properties
mtd: st_spi_fsm: Switch from CONFIG_PM_SLEEP guards to pm_sleep_ptr()
mtd: rawnand: davinci: add ROM supported OOB layout
mtd: spi-nor: sysfs: constify 'struct bin_attribute'
mtd: spi-nor: spansion: Add support for S28HL02GT
mtd: spi-nor: spansion: Add support for S28HL256T
mtd: spi-nor: extend description of size member of struct flash_info
mtd: rawnand: davinci: Reduce polling interval in NAND_OP_WAITRDY_INSTR
mtd: rawnand: qcom: Fix build issue on x86 architecture
mtd: rawnand: qcom: use FIELD_PREP and GENMASK
mtd: nand: Add qpic_common API file
mtd: rawnand: qcom: Add qcom prefix to common api
...
A new controller driver, from Nuvoton, has been merged.
Bastien Curutchet has contributed a series improving the Davinci
controller driver, both on the organization of the code, but also on the
performance side. The binding has also been converted to yaml, received
a new OOB layout and now supports on-die ECC engines.
The Qualcomm controller driver has been deeply cleaned to extract some
parts of the code into a shared file with the Qualcomm SPI memory
controller.
Aside from these main changes, the Cadence binding has been converted to
yaml, the brcmnand controller driver has received a small fix, otherwise
some more minor changes have also made their way in.
* SPI NAND changes
The SPI NAND subsystem has seen a great improvement, with the advent of
DTR operations (DDR operations, which may be extended to the address
cycles). The first vendor driver to benefit from these improvements is
the Winbond driver.
A new manufacturer driver is added SkyHigh, with a new constraint for
the core, it is impossible to disable the on-die ECC engine.
A Foresee device is also now supported.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmeSyFIACgkQJWrqGEe9
VoQqiwgAvsHzKruJpqBDNvQpNnZ0itNh9jUqP2PJ0eQ7toj1vXZ2FUPMH7s4M3/E
KB5TJBIwLoSk59Un8DeTga1SuaHW37j3rWJeQUCR4jgNJ0OuYvFODfXO+4ZOXdS4
qm0prqALQsMBwrYJF8K19EoqUixraQ7WiEVhXmVN965ddYvAsW0E4VMLYg4qrnbB
dvGWe5phg+UEHhmcGXola/JX5yVIC7SeBPEao267ZuRAnLH1zZS1TdllrBF0Cpeg
vac1++i2E1xOkRCqaNipH2oRMiuM1L3BMPukK6pUy4InanXVT6WWm3ekqUEJARIs
JHD4N//Sl7snWpIUhjkVHy9F/7r4yA==
=m1w2
-----END PGP SIGNATURE-----
Merge tag 'nand/for-6.14' into mtd/next
* Raw NAND changes
A new controller driver, from Nuvoton, has been merged.
Bastien Curutchet has contributed a series improving the Davinci
controller driver, both on the organization of the code, but also on the
performance side. The binding has also been converted to yaml, received
a new OOB layout and now supports on-die ECC engines.
The Qualcomm controller driver has been deeply cleaned to extract some
parts of the code into a shared file with the Qualcomm SPI memory
controller.
Aside from these main changes, the Cadence binding has been converted to
yaml, the brcmnand controller driver has received a small fix, otherwise
some more minor changes have also made their way in.
* SPI NAND changes
The SPI NAND subsystem has seen a great improvement, with the advent of
DTR operations (DDR operations, which may be extended to the address
cycles). The first vendor driver to benefit from these improvements is
the Winbond driver.
A new manufacturer driver is added SkyHigh, with a new constraint for
the core, it is impossible to disable the on-die ECC engine.
A Foresee device is also now supported.
Notable changes:
- Add flash entries for Atmel AT25SF321, Spansion S28HL256T, S28HL02GT.
- Add support for vcc-supply regulators and their DT bindings.
- Drop mx25u25635f entry. The flash shares its ID with mx25u25645g and
both parts have an SFDP table. Removing their entry lets them be
driven by the generic SFDP-based driver.
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQQTlUWNzXGEo3bFmyIR4drqP028CQUCZ4VXbBQccHJhdHl1c2hA
a2VybmVsLm9yZwAKCRAR4drqP028Cb9+AQDDUObpSbXfSXCkk5pgGjPOocrKLjLc
gH8+426T1qO4/gEA0tgKfCSxqX6kL7gRGdyxbWRmilfqLDsi5jnn1z3Xtgc=
=ibVz
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-6.14' into mtd/next
SPI NOR changes for 6.14
Notable changes:
- Add flash entries for Atmel AT25SF321, Spansion S28HL256T, S28HL02GT.
- Add support for vcc-supply regulators and their DT bindings.
- Drop mx25u25635f entry. The flash shares its ID with mx25u25645g and
both parts have an SFDP table. Removing their entry lets them be
driven by the generic SFDP-based driver.
This is a fairly quiet release for the most part, though we do have one
really nice improvement in the spi-mem framework which will improve
performance for flash devices especially when built on by changes in the
MTD subsystem which are also due to be sent this merge window. There's
also been some substantial work on some of the drivers, highlights
include:
- Support for per-operation bus frequency in the spi-mem framework,
meaning speeds are no longer limited by the slowest operation.
- ACPI support and improved power management for Rockchip SFC
controllers.
- Support for Atmel SAM7G5 QuadSPI and KEBA SPI controllers.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmeOY7sACgkQJNaLcl1U
h9AA2gf/Zb0B7R5aVlW46OWTYNklvO/yu/3JmVFnd+BdRjr+0/UpnUQ8SAnsFuiK
uX1Mw241SpngI4naqhLdR28SP6dMFyi+/5Orl2/kIzx6RSmCMbNDiw56x71KcXFl
pPjDHRdWOTdRiOwa37/wniaP6wDoWsF4F6sI1jazZP0tc7u+QwT9Hgu+jkzUIQfS
8eSS1W7zOHxqKVohsOb4V8ddVHGbS7EyTbm5RuMOtWP08pTIgzMdQo76WUTkRjLe
8N0PNIbDZSSFLF//DMhTZgeD63cjPN4y7UsM1Z8jrKBtLrEzKSPy/bI/IpnLYyd2
Wdpp2mSCGtRvBO0zU59/HOMv8jYkXw==
=mFrM
-----END PGP SIGNATURE-----
Merge tag 'spi-v6.14' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"This is a fairly quiet release for the most part, though we do have
one really nice improvement in the spi-mem framework which will
improve performance for flash devices especially when built on by
changes in the MTD subsystem which are also due to be sent this merge
window.
There's also been some substantial work on some of the drivers,
highlights include:
- Support for per-operation bus frequency in the spi-mem framework,
meaning speeds are no longer limited by the slowest operation
- ACPI support and improved power management for Rockchip SFC
controllers
- Support for Atmel SAM7G5 QuadSPI and KEBA SPI controllers"
* tag 'spi-v6.14' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (49 commits)
spi: pxa2xx: Introduce __lpss_ssp_update_priv() helper
spi: ti-qspi: Use syscon_regmap_lookup_by_phandle_args
spi: amd: Fix -Wuninitialized in amd_spi_exec_mem_op()
spi: spi-mem: Estimate the time taken by operations
spi: spi-mem: Create macros for DTR operation
spi: spi-mem: Reorder spi-mem macro assignments
spi: zynqmp-gqspi: Support per spi-mem operation frequency switches
spi: zynq-qspi: Support per spi-mem operation frequency switches
spi: spi-ti-qspi: Support per spi-mem operation frequency switches
spi: spi-sn-f-ospi: Support per spi-mem operation frequency switches
spi: rockchip-sfc: Support per spi-mem operation frequency switches
spi: nxp-fspi: Support per spi-mem operation frequency switches
spi: mxic: Support per spi-mem operation frequency switches
spi: mt65xx: Support per spi-mem operation frequency switches
spi: microchip-core-qspi: Support per spi-mem operation frequency switches
spi: fsl-qspi: Support per spi-mem operation frequency switches
spi: dw: Support per spi-mem operation frequency switches
spi: cadence-qspi: Support per spi-mem operation frequency switches
spi: amlogic-spifc-a1: Support per spi-mem operation frequency switches
spi: amd: Drop redundant check
...
-----BEGIN PGP SIGNATURE-----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=EXYs
-----END PGP SIGNATURE-----
Merge tag 'for-6.14/block-20250118' of git://git.kernel.dk/linux
Pull block updates from Jens Axboe:
- NVMe pull requests via Keith:
- Target support for PCI-Endpoint transport (Damien)
- TCP IO queue spreading fixes (Sagi, Chaitanya)
- Target handling for "limited retry" flags (Guixen)
- Poll type fix (Yongsoo)
- Xarray storage error handling (Keisuke)
- Host memory buffer free size fix on error (Francis)
- MD pull requests via Song:
- Reintroduce md-linear (Yu Kuai)
- md-bitmap refactor and fix (Yu Kuai)
- Replace kmap_atomic with kmap_local_page (David Reaver)
- Quite a few queue freeze and debugfs deadlock fixes
Ming introduced lockdep support for this in the 6.13 kernel, and it
has (unsurprisingly) uncovered quite a few issues
- Use const attributes for IO schedulers
- Remove bio ioprio wrappers
- Fixes for stacked device atomic write support
- Refactor queue affinity helpers, in preparation for better supporting
isolated CPUs
- Cleanups of loop O_DIRECT handling
- Cleanup of BLK_MQ_F_* flags
- Add rotational support for null_blk
- Various fixes and cleanups
* tag 'for-6.14/block-20250118' of git://git.kernel.dk/linux: (106 commits)
block: Don't trim an atomic write
block: Add common atomic writes enable flag
md/md-linear: Fix a NULL vs IS_ERR() bug in linear_add()
block: limit disk max sectors to (LLONG_MAX >> 9)
block: Change blk_stack_atomic_writes_limits() unit_min check
block: Ensure start sector is aligned for stacking atomic writes
blk-mq: Move more error handling into blk_mq_submit_bio()
block: Reorder the request allocation code in blk_mq_submit_bio()
nvme: fix bogus kzalloc() return check in nvme_init_effects_log()
md/md-bitmap: move bitmap_{start, end}write to md upper layer
md/raid5: implement pers->bitmap_sector()
md: add a new callback pers->bitmap_sector()
md/md-bitmap: remove the last parameter for bimtap_ops->endwrite()
md/md-bitmap: factor behind write counters out from bitmap_{start/end}write()
md: Replace deprecated kmap_atomic() with kmap_local_page()
md: reintroduce md-linear
partitions: ldm: remove the initial kernel-doc notation
blk-cgroup: rwstat: fix kernel-doc warnings in header file
blk-cgroup: fix kernel-doc warnings in header file
nbd: fix partial sending
...
The SPINAND_PAGE_READ_FROM_CACHE_OP macro has just been changed to stop
encoding the "fast" parameter (the macro has been duplicated and
renamed). The Skyhigh driver is new and is still using the old style
macro.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202501161302.bQqBGjJ5-lkp@intel.com/
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Closes: https://lore.kernel.org/linux-kernel/20250116132010.4948547d@canb.auug.org.au/
Fixes: 0420872478 ("mtd: spinand: Create distinct fast and slow read from cache variants")
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Stephen Rothwell <sfr@canb.auug.org.au> # build tested
On risc V platform, there is a type conversion for the return value
(unsigned long type) of __untagged_addr_remote() in function
untagged_addr(). The compiler will complain when the parameter 'addr'
is an array type:
arch/riscv/include/asm/uaccess.h:33:9: error: cast specifies array type
(__force __typeof__(addr))__untagged_addr_remote(current->mm, __addr)
Fix it by converting the input parameter as a pointer.
Fixes: 01099f635a ("ubi: Implement ioctl for detailed erase counters")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202501191405.WYnmdL0U-lkp@intel.com/
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Currently, "max_ec" can be read from sysfs, which provides a limited
view of the flash device’s wear. In certain cases, such as bugs in
the wear-leveling algorithm, specific blocks can be worn down more
than others, resulting in uneven wear distribution. Also some use cases
can wear the erase blocks of the fastmap area more heavily than other
parts of flash.
Providing detailed erase counter values give a better understanding of
the overall flash wear and is needed to be able to calculate for example
expected life time.
There exists more detailed info in debugfs, but this information is
only available for debug builds.
Signed-off-by: Rickard Andersson <rickard.andersson@axis.com>
Tested-by: Zhihao Cheng <chengzhihao1@huawei.com>
Reviewed-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Commit 5580cdae05 ("ubi: wl: Close down wear-leveling before nand is
suspended") added a reboot notification in UBI layer to shutdown the
wear-leveling subsystem, which imported an UAF problem[1]. Besides that,
the method also brings other potential UAF problems, for example:
reboot kworker
ubi_wl_reboot_notifier
ubi_wl_close
ubi_fastmap_close
kfree(ubi->fm)
update_fastmap_work_fn
ubi_update_fastmap
old_fm = ubi->fm
if (old_fm && old_fm->e[i]) // UAF!
Actually, the problem fixed by commit 5580cdae05 ("ubi: wl: Close down
wear-leveling before nand is suspended") has been solved by commit
8cba323437 ("mtd: rawnand: protect access to rawnand devices while in
suspend"), which was discussed in [2]. So we can revert the commit
5580cdae05 ("ubi: wl: Close down wear-leveling before nand is
suspended") directly.
[1] https://lore.kernel.org/linux-mtd/20241208175211.9406-2-dennis.lamerice@gmail.com/
[2] https://lore.kernel.org/all/9bf76f5d-12a4-46ff-90d4-4a7f0f47c381@axis.com/
Fixes: 5580cdae05 ("ubi: wl: Close down wear-leveling before nand is suspended")
Reported-by: Dennis Lam <dennis.lamerice@gmail.com>
Closes: https://lore.kernel.org/linux-mtd/20241208175211.9406-2-dennis.lamerice@gmail.com/
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Acked-by: Mårten Lindahl <marten.lindahl@axis.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Added a check for ubi_num for negative numbers
If the variable ubi_num takes negative values then we get:
qemu-system-arm ... -append "ubi.mtd=0,0,0,-22222345" ...
[ 0.745065] ubi_attach_mtd_dev from ubi_init+0x178/0x218
[ 0.745230] ubi_init from do_one_initcall+0x70/0x1ac
[ 0.745344] do_one_initcall from kernel_init_freeable+0x198/0x224
[ 0.745474] kernel_init_freeable from kernel_init+0x18/0x134
[ 0.745600] kernel_init from ret_from_fork+0x14/0x28
[ 0.745727] Exception stack(0x90015fb0 to 0x90015ff8)
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 83ff59a066 ("UBI: support ubi_num on mtd.ubi command line")
Cc: stable@vger.kernel.org
Signed-off-by: Denis Arefev <arefev@swemel.ru>
Reviewed-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
W25N01JW and W25N02JW support many DTR read modes in single, dual and
quad configurations.
DTR modes however cannot be used at 166MHz, as the bus frequency in
this case must be lowered to 80MHz.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
W25N01JW and W25N02JW use a different technology with higher frequencies
supported (up to 166MHz). There is one drawback though, the slowest
READ_FROM_CACHE command cannot run above 54MHz. Because of that, we need
to set a limit for these chips on the basic READ_FROM_CACHE variant.
Duplicating this list is not a problem because these chips have DTR
support, and the list of supported variants will diverge from all the
other chips when adding support for it.
Cc: stable+noautosel@kernel.org # New feature being added
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Currently the best variant picked in the first one in the list provided
in the manufacturer driver. This worked well while all operations where
performed at the same speed, but with the introduction of DTR transfers
and per operation maximum frequencies, this no longer works correctly.
Let's continue iterating over all the alternatives, even if we find a
match, keeping a reference over the theoretically fastest
operation. Only at the end we can tell which variant is the best.
This logic happening only once at boot, the extra computing needed
compared to the previous version is acceptable wrt. the expected
improvements.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
So far, the SPINAND_PAGE_READ_FROM_CACHE_OP macro was taking a first
argument, "fast", which was inducing the possibility to support higher
bus frequencies than with the normal (slower) read from cache
alternative. In practice, without frequency change on the bus, this was
likely without effect, besides perhaps allowing another variant of the
same command, that could run at the default highest speed. If we want to
support this fully, we need to add a frequency parameter to the slowest
command. But before we do that, let's drop the "fast" boolean from the
macro and duplicate it, this will further help supporting having
different frequencies allowed for each variant.
The change is also of course propagated to all users. It has the nice
effect to have all macros aligned on the same pattern.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The use of of_property_read_bool() for non-boolean properties is
deprecated in favor of of_property_present() when testing for property
presence.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Letting the compiler remove these functions when the kernel is built
without CONFIG_PM_SLEEP support is simpler and less error prone than the
use of #ifdef based kernel configuration guards.
Signed-off-by: Raphael Gallais-Pou <rgallaispou@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Changes to support DTR with spi-mem.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmeGgAIACgkQJNaLcl1U
h9CodQf9Eek9Usqn6GzjYI8MEAv5XfB0TjG/gleATAtc7Zk4R0Vwo4COnx2+5Fo/
03CV8yAt4Z0fjsD5mzWdnoiVNKCumpS+aFlzwVlOMq1KMYMH1AZAjqYeK9nHYpSn
U5lGse0C9DGrv2jb2KNA5yKGHL/ZquRyY4h0+CKG85jGpmpAWqBAcXaqXm02ts2Q
lTlymD0yefnatQ/0MrGj8bZF0q90Y7oTARDwMyh/MKMpPJslYI5AUT2USKT0qZsp
7sp9SpDE6gyoZy3q0sDXrmRKvMLpV5oLVN5amREnnokNeD9FAP8swDbNH48Fbrlm
4zE4CaHWv2mPSrcbBSJRZRNT/+Neqg==
=uA3v
-----END PGP SIGNATURE-----
Merge tag 'spi-mem-dtr-2' into nand/next
spi: Support DTR in spi-mem
Changes to support DTR with spi-mem.
Add support for the OOB layout used by the ROM bootloader.
The same layout is used by both Keystone [1] and OMAPL138/DA850 [2]
which currently is the only users of davinci-nand.
Only select this layout if the `nand-is-boot-medium` property is set.
This to avoid breaking any existing devices out there.
[1] https://www.ti.com/lit/ug/spruhj3/spruhj3.pdf
[2] https://www.ti.com/lit/an/sprab41f/sprab41f.pdf
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This reverts commit 98d1fb94ce.
The commit uses data nbits instead of addr nbits for dummy phase. This
causes a regression for all boards where spi-tx-bus-width is smaller
than spi-rx-bus-width. It is a common pattern for boards to have
spi-tx-bus-width == 1 and spi-rx-bus-width > 1. The regression causes
all reads with a dummy phase to become unavailable for such boards,
leading to a usually slower 0-dummy-cycle read being selected.
Most controllers' supports_op hooks call spi_mem_default_supports_op().
In spi_mem_default_supports_op(), spi_mem_check_buswidth() is called to
check if the buswidths for the op can actually be supported by the
board's wiring. This wiring information comes from (among other things)
the spi-{tx,rx}-bus-width DT properties. Based on these properties,
SPI_TX_* or SPI_RX_* flags are set by of_spi_parse_dt().
spi_mem_check_buswidth() then uses these flags to make the decision
whether an op can be supported by the board's wiring (in a way,
indirectly checking against spi-{rx,tx}-bus-width).
Now the tricky bit here is that spi_mem_check_buswidth() does:
if (op->dummy.nbytes &&
spi_check_buswidth_req(mem, op->dummy.buswidth, true))
return false;
The true argument to spi_check_buswidth_req() means the op is treated as
a TX op. For a board that has say 1-bit TX and 4-bit RX, a 4-bit dummy
TX is considered as unsupported, and the op gets rejected.
The commit being reverted uses the data buswidth for dummy buswidth. So
for reads, the RX buswidth gets used for the dummy phase, uncovering
this issue. In reality, a dummy phase is neither RX nor TX. As the name
suggests, these are just dummy cycles that send or receive no data, and
thus don't really need to have any buswidth at all.
Ideally, dummy phases should not be checked against the board's wiring
capabilities at all, and should only be sanity-checked for having a sane
buswidth value. Since we are now at rc7 and such a change might
introduce many unexpected bugs, revert the commit for now. It can be
sent out later along with the spi_mem_check_buswidth() fix.
Fixes: 98d1fb94ce ("mtd: spi-nor: core: replace dummy buswidth from addr to data")
Reported-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Closes: https://lore.kernel.org/linux-mtd/3342163.44csPzL39Z@steina-w/
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The sysfs core now allows instances of 'struct bin_attribute' to be
moved into read-only memory. Make use of that to protect them against
accidental or malicious modifications.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Acked-by: Pratyush Yadav <pratyush@kernel.org>
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20241222-sysfs-const-bin_attr-mtd-v1-1-ee13140a4e9b@weissschuh.net
We use the size as an indicator whether to parse SFDP or not. We don't
introduce a dedicated member for SFDP parsing because we'd like to keep
the struct size at a minimum, as it's used for every flash declaration.
Ideally we won't have flash entries at all, but there are still flash
parameters that aren't defined by SFDP, thus we need to statically
specify them.
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20241219-spi-nor-flash-info-size-desc-v1-1-6b53cf011027@linaro.org
In the spi subsystem, the bus frequency is derived as follows:
- the controller may expose a minimum and maximum operating frequency
- the hardware description, through the spi peripheral properties,
advise what is the maximum acceptable frequency from a device/wiring
point of view.
Transfers must be observed at a frequency which fits both (so in
practice, the lowest maximum).
Actually, this second point mixes two information and already takes the
lowest frequency among:
- what the spi device is capable of (what is written in the component
datasheet)
- what the wiring allows (electromagnetic sensibility, crossovers,
terminations, antenna effect, etc).
This logic works until spi devices are no longer capable of sustaining
their highest frequency regardless of the operation. Spi memories are
typically subject to such variation. Some devices are capable of
spitting their internally stored data (essentially in read mode) at a
very fast rate, typically up to 166MHz on Winbond SPI-NAND chips, using
"fast" commands. However, some of the low-end operations, such as
regular page read-from-cache commands, are more limited and can only be
executed at 54MHz at most. This is currently a problem in the SPI-NAND
subsystem. Another situation, even if not yet supported, will be with
DTR commands, when the data is latched on both edges of the clock. The
same chips as mentioned previously are in this case limited to
80MHz. Yet another example might be continuous reads, which, under
certain circumstances, can also run at most at 104 or 120MHz.
As a matter of fact, the "one frequency per chip" policy is outdated and
more fine grain configuration is needed: we need to allow per-operation
frequency limitations. So far, all datasheets I encountered advertise a
maximum default frequency, which need to be lowered for certain specific
operations. So based on the current infrastructure, we can still expect
firmware (device trees in general) to continued advertising the same
maximum speed which is a mix between the PCB limitations and the chip
maximum capability, and expect per-operation lower frequencies when this
is relevant.
Add a `struct spi_mem_op` member to carry this information. Not
providing this field explicitly from upper layers means that there is no
further constraint and the default spi device maximum speed will be
carried instead. The SPI_MEM_OP() macro is also expanded with an
optional frequency argument, because virtually all operations can be
subject to such a limitation, and this will allow for a smooth and
discrete transition.
For controller drivers which do not implement the spi-mem interface, the
per-transfer speed is also set acordingly to a lower (than the maximum
default) speed when relevant.
Acked-by: Pratyush Yadav <pratyush@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20241224-winbond-6-11-rc1-quad-support-v2-1-ad218dbc406f@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
For each NAND_OP_WAITRDY_INSTR operation, the NANDFSR register is
polled only once every 100 us to check for the EMA_WAIT pin. This
isn't frequent enough and causes delays in NAND accesses.
Set the polling interval to 5 us. It increases the page read speed
reported by flash_speed by ~30% (~10% on page writes).
Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Fix a buffer overflow issue in qcom_clear_bam_transaction by using
struct_group to group related fields and avoid FORTIFY_SOURCE warnings.
On x86 architecture, the following error occurs due to warnings being
treated as errors:
In function ‘fortify_memset_chk’,
inlined from ‘qcom_clear_bam_transaction’ at
drivers/mtd/nand/qpic_common.c:88:2:
./include/linux/fortify-string.h:480:25: error: call to ‘__write_overflow_field’
declared with attribute warning: detected write beyond size of field
(1st parameter); maybe use struct_group()? [-Werror=attribute-warning]
480 | __write_overflow_field(p_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
LD [M] drivers/mtd/nand/nandcore.o
CC [M] drivers/w1/masters/mxc_w1.o
cc1: all warnings being treated as errors
This patch addresses the issue by grouping the related fields in
struct bam_transaction using struct_group and updating the memset call
accordingly.
Fixes: 8c52932da5 ("mtd: rawnand: qcom: cleanup qcom_nandc driver")
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
the spi bits adding the Qcom SPI-NAND controller driver re-using a lot
of code that has been shared.
With this goal in mind, the raw NAND controller driver has been cleaned
up and reorganized, and only the relevant structures/helpers which have
nothing raw NAND specific should now be exported.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmdq0moACgkQJWrqGEe9
VoS3cwgAh+aISqETMIQbG8/i2LzbBjzCAEDKC1nwnk2buwlvJC8omUDF6xpBe1AL
grN3j5ltmlDj834+S8UI9/9QFYExrKp3SlDzzbvdpDNgGsgFT56B2Mq0eZfju2b0
BXUuMUllKZGR6bm1ddKwEvFtgqulJdBiTOD28PIDsW1+ZgpFPLN7wYzyAme3s6Aw
xwqwthUWt7J3zXTMRxBAqwBG63Xkb30AiF0q7EYNzjZ6455c/XIJcTSmDTI9/Wx1
O2oBbG7EpbXlMISosiDkbBrfCseDduGpZLeCE7pMDkWpsdFJbV5qeM4z3UJvQ9vu
rLRMtSEhJ6tJF/dRn+YlqlIz72uKsQ==
=BqI2
-----END PGP SIGNATURE-----
Merge tag 'mtd/qcom-reorg-for-spi-6.14' into nand/next
Topic branch with preparation changes from Qcom in order to apply on top
the spi bits adding the Qcom SPI-NAND controller driver re-using a lot
of code that has been shared.
With this goal in mind, the raw NAND controller driver has been cleaned
up and reorganized, and only the relevant structures/helpers which have
nothing raw NAND specific should now be exported.
Use the bitfield macro FIELD_PREP, and GENMASK to
do the shift and mask in one go. This makes the code
more readable.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add qpic_common.c file which hold all the common
qpic APIs which will be used by both qpic raw nand
driver and qpic spi nand driver.
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add qcom prefix to all the api which will be commonly
used by spi nand driver and raw nand driver.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Perform a global cleanup of the Qualcomm NAND
controller driver with the following improvements:
- Remove register value indirection API
- Remove set_reg() API
- Convert read_loc_first & read_loc_last macro to functions
- Rename multiple variables
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The setup_interface() operation isn't implemented. It forces the driver
to use the ONFI mode 0, though it could use more optimal modes.
Implement the setup_interface() operation. It uses the
aemif_set_cs_timings() function from the AEMIF driver to update the
chip select timings. The calculation of the register's contents is
directly extracted from §20.3.2.3 of the DaVinci TRM [1]
MAX_TH_PS and MAX_TSU_PS are the worst case timings based on the
Keystone2 and DaVinci datasheets.
[1] : https://www.ti.com/lit/ug/spruh77c/spruh77c.pdf
Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
NAND controller has a reference clock inherited from the AEMIF
(cf. Documentation/devicetree/bindings/memory-controllers/ti-aemif.txt)
This clock isn't used yet by the driver.
Add a struct clock in the struct davinci_nand_info so it can be used
to compute timings.
Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In am654_hbmc_platform_driver, .remove() and the error path of .probe()
do not decrement the refcount of an OF node obtained by
of_get_next_child(). Fix this by adding of_node_put() calls.
Fixes: aca31ce968 ("mtd: hyperbus: hbmc-am654: Fix direct mapping setup flash access")
Signed-off-by: Joe Hattori <joe@pf.is.s.u-tokyo.ac.jp>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Nuvoton MA35 SoCs NAND Flash Interface Controller
supports 2kiB, 4kiB and 8kiB page size, and up to
8-bit, 12-bit, and 24-bit hardware ECC calculation
circuit to protect data.
Signed-off-by: Hui-Ping Chen <hpchen0nvt@gmail.com>
[Miquel Raynal: Fixed compatible and driver name to match latest bindings]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This change fixes an issue where an error return value may be mistakenly
used as NAND status.
Fixes: f504551b7f ("mtd: rawnand: Propagate error and simplify ternary operators for brcmstb_nand_wait_for_completion()")
Signed-off-by: david regan <dregan@broadcom.com>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
BLK_MQ_F_SHOULD_MERGE is set for all tag_sets except those that purely
process passthrough commands (bsg-lib, ufs tmf, various nvme admin
queues) and thus don't even check the flag. Remove it to simplify the
driver interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20241219060214.1928848-1-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The Macronix mx25u25635f flash device supports SFDP initialization.
This commit removes the specific mx25u25635f entry (NOR ID 0xc22539),
along with its size and flags, from the NOR parts list. By removing
this entry, both mx25u25635f and mx25u25645g (which share the same
NOR ID) will utilize the generic flash driver configuration.
This change allows both devices (mx25u25635f and mx25u25645g) to
leverage SFDP-defined parameters, enabling dual and quad read
operations without the need for manual adjustment of no_sfdp_flags.
Link: https://www.macronix.com/Lists/Datasheet/Attachments/8663/MX25U25635F,%201.8V,%20256Mb,%20v1.5.pdf
Signed-off-by: Parth Pancholi <parth.pancholi@toradex.com>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20241105105844.257676-1-parth105105@gmail.com
SPI NOR flashes needs power supply to work properly. The power supply
maybe software controllable per board design. So add the support
for an vcc-supply regulator.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
[ta: move devm_regulator_get_enable() to spi_nor_probe().]
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20241111111946.9048-3-tudor.ambarus@linaro.org
Use a local variable for the struct device pointers to avoid
dereferencing.
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20241111111946.9048-2-tudor.ambarus@linaro.org
Use the nor->addr_nbytes set by the core, we shouldn't use
magic numbers or states that are not tracked by the core.
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Acked-by: Pratyush Yadav <pratyush@kernel.org>
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20241111113609.12093-1-tudor.ambarus@linaro.org
The Fujitsu FRAM chips use the same command set as Microchip EERAM.
The only differences are that the Fujitsu FRAM chips don't really have a
page size limit, nor do they automatically reset the WEL bit.
Signed-off-by: David Jander <david@protonic.nl>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Jonas Rebmann <jre@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The 48L640 resets the WEL bit (the Write Enable Latch bit in the status
register) to zero on the completion of write operations. In preparation
to support chips behaving differently, introduce .auto_disable_wel
capability, and, if it's missing, explicitly reset the WEL bit after
writes.
Signed-off-by: David Jander <david@protonic.nl>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Jonas Rebmann <jre@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add kernel-doc for functions to get rid of below warnings
when built with W=1.
drivers/mtd/nand/raw/omap2.c:260: warning: Function parameter or struct member 'chip' not described in 'omap_nand_data_in_pref'
drivers/mtd/nand/raw/omap2.c:260: warning: Function parameter or struct member 'buf' not described in 'omap_nand_data_in_pref'
drivers/mtd/nand/raw/omap2.c:260: warning: Function parameter or struct member 'len' not described in 'omap_nand_data_in_pref'
drivers/mtd/nand/raw/omap2.c:260: warning: Function parameter or struct member 'force_8bit' not described in 'omap_nand_data_in_pref'
drivers/mtd/nand/raw/omap2.c:304: warning: Function parameter or struct member 'chip' not described in 'omap_nand_data_out_pref'
drivers/mtd/nand/raw/omap2.c:304: warning: Function parameter or struct member 'buf' not described in 'omap_nand_data_out_pref'
drivers/mtd/nand/raw/omap2.c:304: warning: Function parameter or struct member 'len' not described in 'omap_nand_data_out_pref'
drivers/mtd/nand/raw/omap2.c:304: warning: Function parameter or struct member 'force_8bit' not described in 'omap_nand_data_out_pref'
drivers/mtd/nand/raw/omap2.c:446: warning: Function parameter or struct member 'chip' not described in 'omap_nand_data_in_dma_pref'
drivers/mtd/nand/raw/omap2.c:446: warning: Function parameter or struct member 'buf' not described in 'omap_nand_data_in_dma_pref'
drivers/mtd/nand/raw/omap2.c:446: warning: Function parameter or struct member 'len' not described in 'omap_nand_data_in_dma_pref'
drivers/mtd/nand/raw/omap2.c:446: warning: Function parameter or struct member 'force_8bit' not described in 'omap_nand_data_in_dma_pref'
drivers/mtd/nand/raw/omap2.c:467: warning: Function parameter or struct member 'chip' not described in 'omap_nand_data_out_dma_pref'
drivers/mtd/nand/raw/omap2.c:467: warning: Function parameter or struct member 'buf' not described in 'omap_nand_data_out_dma_pref'
drivers/mtd/nand/raw/omap2.c:467: warning: Function parameter or struct member 'len' not described in 'omap_nand_data_out_dma_pref'
drivers/mtd/nand/raw/omap2.c:467: warning: Function parameter or struct member 'force_8bit' not described in 'omap_nand_data_out_dma_pref'
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202412031716.JfNIh1Uu-lkp@intel.com/
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
SkyHigh S35ML01G300, S35ML01G301, S35ML02G300, and S35ML04G300 are 1Gb,
2Gb, and 4Gb SLC SPI NAND flash family. This family of devices has
on-die ECC which parity bits are stored to hidden area. In this family
the on-die ECC cannot be disabled so raw access needs to be prevented.
Link: https://www.skyhighmemory.com/download/SPI_S35ML01_04G3_002_19205.pdf?v=P
Co-developed-by: KR Kim <kr.kim@skyhighmemory.com>
Signed-off-by: KR Kim <kr.kim@skyhighmemory.com>
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
SkyHigh spinand device has ECC enable bit in configuration register but
it must be always enabled. If ECC is disabled, read and write ops
results in undetermined state. For such devices, a way to avoid raw
access is needed.
Introduce SPINAND_NO_RAW_ACCESS flag to advertise the device does not
support raw access. In such devices, the on-die ECC engine ops returns
error to I/O request in raw mode.
Checking and marking BBM need to be cared as special case, by adding
fallback mechanism that tries read/write OOB with ECC enabled.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
We don't have to call spinand_write_enable_op() in spinand_markbad() as
it is called in spinand_write_page().
Fixes: b645ad39d5 ("mtd: spinand: Do not erase the block before writing a bad block marker")
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The NAND chip-selects are registered for the Arasan driver during
initialization but are not de-registered when the driver is unloaded. As a
result, if the driver is loaded again, the chip-selects remain registered
and busy, making them unavailable for use.
Fixes: 197b88fecc ("mtd: rawnand: arasan: Add new Arasan NAND controller")
Cc: stable@vger.kernel.org
Signed-off-by: Maciej Andrzejewski ICEYE <maciej.andrzejewski@m-works.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
When two chip-selects are configured in the device tree, and the second is
a non-native GPIO, both the GPIO-based chip-select and the first native
chip-select may be asserted simultaneously. This double assertion causes
incorrect read and write operations.
The issue occurs because when nfc->ncs <= 2, nfc->spare_cs is always
initialized to 0 due to static initialization. Consequently, when the
second chip-select (GPIO-based) is selected in anfc_assert_cs(), it is
detected by anfc_is_gpio_cs(), and nfc->native_cs is assigned the value 0.
This results in both the GPIO-based chip-select being asserted and the
NAND controller register receiving 0, erroneously selecting the native
chip-select.
This patch resolves the issue, as confirmed by oscilloscope testing with
configurations involving two or more chip-selects in the device tree.
Fixes: acbd3d0945 ("mtd: rawnand: arasan: Leverage additional GPIO CS")
Cc: stable@vger.kernel.org
Signed-off-by: Maciej Andrzejewski <maciej.andrzejewski@m-works.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The phram MTD driver may map any memory pages no matter whether it's
reserved or whatever used for systems, which basically allows user
bypassing the lock down.
Add the check and abort the probe if the kernel is locked down for
LOCKDOWN_DEV_MEM.
Reported-by: Fabian Vogt <fvogt@suse.com>
Suggested-by: Fabian Vogt <fvogt@suse.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The function do_otp_read() does not set the output parameter *retlen,
which is expected to contain the number of bytes actually read.
As a result, in onenand_otp_walk(), the tmp_retlen variable remains
uninitialized after calling do_otp_walk() and used to change
the values of the buf, len and retlen variables.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 49dc08eeda ("[MTD] [OneNAND] fix numerous races")
Cc: stable@vger.kernel.org
Signed-off-by: Ivan Stepchenko <sid@itb.spb.ru>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add support for FORESEE F35SQA001G SPI NAND.
Similar to F35SQA002G, but differs in capacity.
Datasheet:
- https://cdn.ozdisan.com/ETicaret_Dosya/704795_871495.pdf
Tested on Xiaomi AX3000T flashed with OpenWRT.
Signed-off-by: Bohdan Chubuk <chbgdn@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The check on ret and call to platform_driver_unregister is only required
in the code path where MODULE is not defined. Fix this by moving this
code into the relevant place after the call to phram_setup.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
There may be a potential integer overflow issue in inftl_partscan().
parts[0].size is defined as "uint64_t" while mtd->erasesize and
ip->firstUnit are defined as 32-bit unsigned integer. The result of
the calculation will be limited to 32 bits without correct casting.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Zichen Xie <zichenxie0106@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Some chips, e.g. Micron MT29F1G08ABBFAH4, has a mandatory on-die ECC.
Add "on-die" as ECC engine type in order to be compatible with those.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The "user" pointer was converted from being allocated with kzalloc() to
being allocated by devm_kzalloc(). Calling kfree(user) will lead to a
double free.
Fixes: 6d734f1bfc ("mtd: rawnand: atmel: Fix possible memory leak")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
JFFS2:
- Bug fix for rtime compression
- Various cleanups
UBI:
- Cleanups for fastmap and wear leveling
UBIFS:
- Add support for FS_IOC_GETFSSYSFSPATH
- Remove dead ioctl code
- Fix UAF in ubifs_tnc_end_commit()
-----BEGIN PGP SIGNATURE-----
iQJKBAABCAA0FiEEdgfidid8lnn52cLTZvlZhesYu8EFAmdKRRIWHHJpY2hhcmRA
c2lnbWEtc3Rhci5hdAAKCRBm+VmF6xi7wTjkD/9eSZ+VKp6vDOzdIS9U+oEiq4Y5
rzbJggyLdpMVdVKuO6Hr6ra+h8q6q0sXzFQ21Gqdxd/JSlikx60VIUzCzcVse9I4
JhVSRu640Z0McgsP6E6H7lBscVpKdvDMeS8MZ/lxJv49qKiAkE7wuHoJxdGApREz
leCkXsUWTE2DkgOHqhjvh+zy5d52oLpb0UIlSsg4TYuG2sfaWPwUEbwxmqS2+E3f
MJwvZhlPb2LaJ8YN5HFjzqxk8PvIwBY9cbDrMdY71SNQdg5h9wJQf7aMtI1Yw717
xoubCJYX18h+y8bW/M3uqeU0R9mdYTqkwn+HF8CY9Czv/BiItz0upXEst5gBbvJ7
8SdOtWX07Efc+oYHARAZ9X37Cu0aKl0IcZecrvyoxWMJKjyXUoAfCE4r6OZncfVN
3FY6URlyqeBBqASnoufMwprv/oNaDqi8EFEgNLo9UYoV9qFU7wAu1UjVDE53xOuU
E3a3oTy/7ArBG1H5b6+5Xr/PxGMeAhO+uHdEUW97WftSkkFXLE7O1rA2o1FKPLOG
I6nKvTnVadBrQVyf3IKbJa17fbTqRi7wJzHDbYbqof6b/dGXqoZwSlF/u1SbQ/oG
dT/T0sJK+Ql8IWpceeqq5AcAFmEcO4jOGlMQfcamWXynO0qapt8RRRUgICvRaovv
76qlCXIh0gNQBHFf6w==
=PpBC
-----END PGP SIGNATURE-----
Merge tag 'ubifs-for-linus-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs
Pull JFFS2, UBI and UBIFS updates from Richard Weinberger:
"JFFS2:
- Bug fix for rtime compression
- Various cleanups
UBI:
- Cleanups for fastmap and wear leveling
UBIFS:
- Add support for FS_IOC_GETFSSYSFSPATH
- Remove dead ioctl code
- Fix UAF in ubifs_tnc_end_commit()"
* tag 'ubifs-for-linus-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs: (25 commits)
ubifs: Fix uninitialized use of err in ubifs_jnl_write_inode()
jffs2: Prevent rtime decompress memory corruption
jffs2: remove redundant check on outpos > pos
fs: jffs2: Fix inconsistent indentation in jffs2_mark_node_obsolete
jffs2: Correct some typos in comments
jffs2: fix use of uninitialized variable
jffs2: Use str_yes_no() helper function
mtd: ubi: remove redundant check on bytes_left at end of function
mtd: ubi: fix unreleased fwnode_handle in find_volume_fwnode()
ubifs: authentication: Fix use-after-free in ubifs_tnc_end_commit
ubi: fastmap: Fix duplicate slab cache names while attaching
ubifs: xattr: remove unused anonymous enum
ubifs: Reduce kfree() calls in ubifs_purge_xattrs()
ubifs: Call iput(xino) only once in ubifs_purge_xattrs()
ubi: wl: Close down wear-leveling before nand is suspended
mtd: ubi: Rmove unused declaration in header file
ubifs: Correct the total block count by deducting journal reservation
ubifs: Convert to use ERR_CAST()
ubifs: add support for FS_IOC_GETFSSYSFSPATH
ubifs: remove unused ioctl flags GETFLAGS/SETFLAGS
...
Here is a small set of driver core changes for 6.13-rc1.
Nothing major for this merge cycle, except for the 2 simple merge
conflicts are here just to make life interesting.
Included in here are:
- sysfs core changes and preparations for more sysfs api cleanups that
can come through all driver trees after -rc1 is out
- fw_devlink fixes based on many reports and debugging sessions
- list_for_each_reverse() removal, no one was using it!
- last-minute seq_printf() format string bug found and fixed in many
drivers all at once.
- minor bugfixes and changes full details in the shortlog
As mentioned above, there is 2 merge conflicts with your tree, one is
where the file is removed (easy enough to resolve), the second is a
build time error, that has been found in linux-next and the fix can be
seen here:
https://lore.kernel.org/r/20241107212645.41252436@canb.auug.org.au
Other than that, the changes here have been in linux-next with no other
reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZ0lEog8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ym+0ACgw6wN+LkLVIHWhxTq5DYHQ0QCxY8AoJrRIcKe
78h0+OU3OXhOy8JGz62W
=oI5S
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is a small set of driver core changes for 6.13-rc1.
Nothing major for this merge cycle, except for the two simple merge
conflicts are here just to make life interesting.
Included in here are:
- sysfs core changes and preparations for more sysfs api cleanups
that can come through all driver trees after -rc1 is out
- fw_devlink fixes based on many reports and debugging sessions
- list_for_each_reverse() removal, no one was using it!
- last-minute seq_printf() format string bug found and fixed in many
drivers all at once.
- minor bugfixes and changes full details in the shortlog"
* tag 'driver-core-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (35 commits)
Fix a potential abuse of seq_printf() format string in drivers
cpu: Remove spurious NULL in attribute_group definition
s390/con3215: Remove spurious NULL in attribute_group definition
perf: arm-ni: Remove spurious NULL in attribute_group definition
driver core: Constify bin_attribute definitions
sysfs: attribute_group: allow registration of const bin_attribute
firmware_loader: Fix possible resource leak in fw_log_firmware_info()
drivers: core: fw_devlink: Fix excess parameter description in docstring
driver core: class: Correct WARN() message in APIs class_(for_each|find)_device()
cacheinfo: Use of_property_present() for non-boolean properties
cdx: Fix cdx_mmap_resource() after constifying attr in ->mmap()
drivers: core: fw_devlink: Make the error message a bit more useful
phy: tegra: xusb: Set fwnode for xusb port devices
drm: display: Set fwnode for aux bus devices
driver core: fw_devlink: Stop trying to optimize cycle detection logic
driver core: Constify attribute arguments of binary attributes
sysfs: bin_attribute: add const read/write callback variants
sysfs: implement all BIN_ATTR_* macros in terms of __BIN_ATTR()
sysfs: treewide: constify attribute callback of bin_attribute::llseek()
sysfs: treewide: constify attribute callback of bin_attribute::mmap()
...
misc issues got fixed.
SPI-NAND changes:
A load of fixes to Winbond manufacturer driver have been done, plus a
structure constification.
Raw NAND changes:
The GPMI driver has been improved on the power management side.
The Davinci driver has been cleaned up.
A leak in the Atmel driver plus some typos in the core have been fixed.
SPI NOR changes:
Introduce byte swap support for 8D-8D-8D mode and a user for it:
macronix. SPI NOR flashes may swap the bytes on a 16-bit boundary when
configured in Octal DTR mode. For such cases the byte order is
propagated through SPI MEM to the SPI controllers so that the
controllers swap the bytes back at runtime. This avoids breaking the
boot sequence because of the endianness problems that appear when the
bootloaders use 1-1-1 and the kernel uses 8D-8D-8D with byte swap
support. Along with the SPI MEM byte swap support we queue a patch for
the SPI MXIC controller that swaps the bytes back at runtime.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmc/WusACgkQJWrqGEe9
VoR0Zgf/admMDFN51dtkz950bnOkZfot/4uLgUQCDenhbugHrom7KWQ6+oh1+HSN
9EAjLoLNQzq4vxKx1WoI/99iJO86zg/DiyVD3nQidv9JkqHRDp2t13ZLclr4gGyW
Kh1lDQ+9GwpB8CQQnxVaPL39NjjqR3RiEfEP/1fVgGYQvCt4yedhVsDT3WThJeVb
1n7l54RBpZji88mT0chFB9CoSLnzrYZFh2MvzJaW/i1v02yZLXHFxFiKiKo+WysY
FGQTY3x0j20H2Ib8RSP7ECegvNb1HtfIxAPsTIqDBGbrA+ahvBr0J/XxX3NbV3RT
Ee4rXqL257zH9dC9Rr1LJAZCqiyx7w==
=p+y9
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"MTD device changes:
- switch platform_driver back to remove()
- misc fixes
SPI-NAND changes:
- a load of fixes to Winbond manufacturer driver
- structure constification
Raw NAND changes:
- improve the power management of the GPMI driver
- Davinci driver clean-ups
- fix leak in the Atmel driver
- fix some typos in the core
SPI NOR changes:
- Introduce byte swap support for 8D-8D-8D mode and a user for it:
macronix.
SPI NOR flashes may swap the bytes on a 16-bit boundary when
configured in Octal DTR mode. For such cases the byte order is
propagated through SPI MEM to the SPI controllers so that the
controllers swap the bytes back at runtime. This avoids breaking
the boot sequence because of the endianness problems that appear
when the bootloaders use 1-1-1 and the kernel uses 8D-8D-8D with
byte swap support. Along with the SPI MEM byte swap support we
queue a patch for the SPI MXIC controller that swaps the bytes back
at runtime"
* tag 'mtd/for-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (25 commits)
mtd: spi-nor: core: replace dummy buswidth from addr to data
mtd: spi-nor: winbond: add "w/ and w/o SFDP" comment
mtd: spi-nor: spansion: Use nor->addr_nbytes in octal DTR mode in RD_ANY_REG_OP
mtd: Switch back to struct platform_driver::remove()
mtd: cfi_cmdset_0002: remove redundant assignment to variable ret
mtd: spinand: Constify struct nand_ecc_engine_ops
MAINTAINERS: add mailing list for GPMI NAND driver
mtd: spinand: winbond: Sort the devices
mtd: spinand: winbond: Ignore the last ID characters
mtd: spinand: winbond: Fix 512GW, 01GW, 01JW and 02JW ECC information
mtd: spinand: winbond: Fix 512GW and 02JW OOB layout
mtd: nand: raw: gpmi: improve power management handling
mtd: nand: raw: gpmi: switch to SYSTEM_SLEEP_PM_OPS
mtd: rawnand: davinci: use generic device property helpers
mtd: rawnand: davinci: break the line correctly
mtd: rawnand: davinci: order headers alphabetically
mtd: rawnand: atmel: Fix possible memory leak
mtd: rawnand: Correct multiple typos in comments
mtd: hyperbus: rpc-if: Add missing MODULE_DEVICE_TABLE
mtd: spi-nor: add support for Macronix Octal flash
...
A load of fixes to Winbond manufacturer driver have been done, plus a
structure constification.
Raw NAND changes:
The GPMI driver has been improved on the power management side.
The Davinci driver has been cleaned up.
A leak in the Atmel driver plus some typos in the core have been fixed.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmc8is0ACgkQJWrqGEe9
VoRXDwf+IqUGLRVdCh9wQFsjEKXBX9lmLF+McG+aumLnpmxq+9iDs0FzPg39gi9W
iSZiYRnVNdOPskEMpJcAnalFcAT56SFjM7IUluxvMG4TKsaWqV7ZCP+fwV+43tyl
57ohTlQCpJnTAqUdARIMVPjIlBaXTsmzyt74nb3hOUGFa5NKwF7PxBP0e504akUP
TohLFHWOO4BeooqkDroz8H3Po+uO3YDVf3l0DsGANptAmA0azDjj+ZUEKOtsNEQw
ZmeZ8sGZGYswrcjYqJAGKXeXBOBmfFSTlEy72cKKqs8KBGqGCRTyoDjVpIBNK+vl
vyMY8AoViWX5nb83Qu85QckJbQlEqw==
=GEHJ
-----END PGP SIGNATURE-----
Merge tag 'nand/for-6.13' into mtd/next
SPI-NAND changes:
A load of fixes to Winbond manufacturer driver have been done, plus a
structure constification.
Raw NAND changes:
The GPMI driver has been improved on the power management side.
The Davinci driver has been cleaned up.
A leak in the Atmel driver plus some typos in the core have been fixed.
-----BEGIN PGP SIGNATURE-----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=o4ww
-----END PGP SIGNATURE-----
Merge tag 'random-6.13-rc1-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random
Pull random number generator updates from Jason Donenfeld:
"This contains a single series from Uros to replace uses of
<linux/random.h> with prandom.h or other more specific headers
as needed, in order to avoid a circular header issue.
Uros' goal is to be able to use percpu.h from prandom.h, which
will then allow him to define __percpu in percpu.h rather than
in compiler_types.h"
* tag 'random-6.13-rc1-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random:
prandom: Include <linux/percpu.h> in <linux/prandom.h>
random: Do not include <linux/prandom.h> in <linux/random.h>
netem: Include <linux/prandom.h> in sch_netem.c
lib/test_scanf: Include <linux/prandom.h> instead of <linux/random.h>
lib/test_parman: Include <linux/prandom.h> instead of <linux/random.h>
bpf/tests: Include <linux/prandom.h> instead of <linux/random.h>
lib/rbtree-test: Include <linux/prandom.h> instead of <linux/random.h>
random32: Include <linux/prandom.h> instead of <linux/random.h>
kunit: string-stream-test: Include <linux/prandom.h>
lib/interval_tree_test.c: Include <linux/prandom.h> instead of <linux/random.h>
bpf: Include <linux/prandom.h> instead of <linux/random.h>
scsi: libfcoe: Include <linux/prandom.h> instead of <linux/random.h>
fscrypt: Include <linux/once.h> in fs/crypto/keyring.c
mtd: tests: Include <linux/prandom.h> instead of <linux/random.h>
media: vivid: Include <linux/prandom.h> in vivid-vid-cap.c
drm/lib: Include <linux/prandom.h> instead of <linux/random.h>
drm/i915/selftests: Include <linux/prandom.h> instead of <linux/random.h>
crypto: testmgr: Include <linux/prandom.h> instead of <linux/random.h>
x86/kaslr: Include <linux/prandom.h> instead of <linux/random.h>
it: macronix. SPI NOR flashes may swap the bytes on a 16-bit boundary
when configured in Octal DTR mode. For such cases the byte order is
propagated through SPI MEM to the SPI controllers so that the controllers
swap the bytes back at runtime. This avoids breaking the boot sequence
because of the endianness problems that appear when the bootloaders use
1-1-1 and the kernel uses 8D-8D-8D with byte swap support. Along with the
SPI MEM byte swap support we queue a patch for the SPI MXIC controller
that swaps the bytes back at runtime.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEHUIqys8OyG1eHf7fS1VPR6WNFOkFAmczG/oACgkQS1VPR6WN
FOnTCAf/YjH9AimQAFJLRKoGqsf6boh1JppcRh1YTRS+D6+Ap9+s1gJoZZYs5VWA
vNfBzGqDXknBvpmOgoXnuDu2zFs9FUvdN5Kf7w6LiS5qtz7uOxHdVoDQyDgnN6w5
9ts7qF7LViBHg/HgTEzQT2Zj6qmvIwUbccIkmJeehWjEP/urzOML5nPnM9g4HZVB
W8B5KQ4TiOY1GxkXvIP6EQS6mDKznP3yl2Hnsmk0HPpSm6D807O2zvT+z1SCxpjy
C8+mYRKsRxHoFGL6UzWgqREGBn2wzF7Ral1CR9SpSZZLLtr6S0shqRzKiiH8eiZK
1hFpXzMS3OWi4a/5724AWaqcR0Qgqw==
=jf3Q
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux into mtd/next
SPI NOR introduces byte swap support for 8D-8D-8D mode and a user for
it: macronix. SPI NOR flashes may swap the bytes on a 16-bit boundary
when configured in Octal DTR mode. For such cases the byte order is
propagated through SPI MEM to the SPI controllers so that the controllers
swap the bytes back at runtime. This avoids breaking the boot sequence
because of the endianness problems that appear when the bootloaders use
1-1-1 and the kernel uses 8D-8D-8D with byte swap support. Along with the
SPI MEM byte swap support we queue a patch for the SPI MXIC controller
that swaps the bytes back at runtime.
# -----BEGIN PGP SIGNATURE-----
#
# iQEzBAABCgAdFiEEHUIqys8OyG1eHf7fS1VPR6WNFOkFAmczG/oACgkQS1VPR6WN
# FOnTCAf/YjH9AimQAFJLRKoGqsf6boh1JppcRh1YTRS+D6+Ap9+s1gJoZZYs5VWA
# vNfBzGqDXknBvpmOgoXnuDu2zFs9FUvdN5Kf7w6LiS5qtz7uOxHdVoDQyDgnN6w5
# 9ts7qF7LViBHg/HgTEzQT2Zj6qmvIwUbccIkmJeehWjEP/urzOML5nPnM9g4HZVB
# W8B5KQ4TiOY1GxkXvIP6EQS6mDKznP3yl2Hnsmk0HPpSm6D807O2zvT+z1SCxpjy
# C8+mYRKsRxHoFGL6UzWgqREGBn2wzF7Ral1CR9SpSZZLLtr6S0shqRzKiiH8eiZK
# 1hFpXzMS3OWi4a/5724AWaqcR0Qgqw==
# =jf3Q
# -----END PGP SIGNATURE-----
# gpg: Signature made Tue 12 Nov 2024 10:12:26 AM CET
# gpg: using RSA key 1D422ACACF0EC86D5E1DFEDF4B554F47A58D14E9
# gpg: Good signature from "Tudor Ambarus (4096-bit rsa key) <tudor.ambarus@microchip.com>" [full]
# gpg: aka "Tudor Ambarus <tudor.ambarus@gmail.com>" [full]
# gpg: tudor.ambarus@microchip.com: Verified 15 signatures in the past 5 years.
# Encrypted 0 messages.
# gpg: tudor.ambarus@gmail.com: Verified 15 signatures in the past 5 years.
# Encrypted 0 messages.
In function ubi_nvmem_reg_read the while-loop can only be exiting
of bytes_left is zero or an error has occurred. There is an exit
return path if an error occurs, so the bytes_left can only be
zero after that point. Hence the check for a non-zero bytes_left
at the end of the function is redundant and can be removed. Remove
the check and just return 0.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
The 'fw_vols' fwnode_handle initialized via
device_get_named_child_node() requires explicit calls to
fwnode_handle_put() when the variable is no longer required.
Add the missing calls to fwnode_handle_put() before the function
returns.
Cc: stable@vger.kernel.org
Fixes: 51932f9fc4 ("mtd: ubi: populate ubi volume fwnode")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Reviewed-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Since commit 4c39529663 ("slab: Warn on duplicate cache names when
DEBUG_VM=y"), the duplicate slab cache names can be detected and a
kernel WARNING is thrown out.
In UBI fast attaching process, alloc_ai() could be invoked twice
with the same slab cache name 'ubi_aeb_slab_cache', which will trigger
following warning messages:
kmem_cache of name 'ubi_aeb_slab_cache' already exists
WARNING: CPU: 0 PID: 7519 at mm/slab_common.c:107
__kmem_cache_create_args+0x100/0x5f0
Modules linked in: ubi(+) nandsim [last unloaded: nandsim]
CPU: 0 UID: 0 PID: 7519 Comm: modprobe Tainted: G 6.12.0-rc2
RIP: 0010:__kmem_cache_create_args+0x100/0x5f0
Call Trace:
__kmem_cache_create_args+0x100/0x5f0
alloc_ai+0x295/0x3f0 [ubi]
ubi_attach+0x3c3/0xcc0 [ubi]
ubi_attach_mtd_dev+0x17cf/0x3fa0 [ubi]
ubi_init+0x3fb/0x800 [ubi]
do_init_module+0x265/0x7d0
__x64_sys_finit_module+0x7a/0xc0
The problem could be easily reproduced by loading UBI device by fastmap
with CONFIG_DEBUG_VM=y.
Fix it by using different slab names for alloc_ai() callers.
Fixes: d2158f69a7 ("UBI: Remove alloc_ai() slab name from parameter list")
Fixes: fdf10ed710 ("ubi: Rework Fastmap attach base code")
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
If a reboot/shutdown signal with double force (-ff) is triggered when
the erase worker or wear-leveling worker function runs we may end up in
a race condition since the MTD device gets a reboot notification and
suspends the nand flash before the erase or wear-leveling is done. This
will reject all accesses to the flash with -EBUSY.
Sequence for the erase worker function:
systemctl reboot -ff ubi_thread
do_work
__do_sys_reboot
blocking_notifier_call_chain
mtd_reboot_notifier
nand_shutdown
nand_suspend
__erase_worker
ubi_sync_erase
mtd_erase
nand_erase_nand
# Blocked by suspended chip
nand_get_device
=> EBUSY
Similar sequence for the wear-leveling function:
systemctl reboot -ff ubi_thread
do_work
__do_sys_reboot
blocking_notifier_call_chain
mtd_reboot_notifier
nand_shutdown
nand_suspend
wear_leveling_worker
ubi_eba_copy_leb
ubi_io_write
mtd_write
nand_write_oob
# Blocked by suspended chip
nand_get_device
=> EBUSY
systemd-shutdown[1]: Rebooting.
ubi0 error: ubi_io_write: error -16 while writing 2048 bytes to PEB
CPU: 1 PID: 82 Comm: ubi_bgt0d Kdump: loaded Tainted: G O
(unwind_backtrace) from [<80107b9f>] (show_stack+0xb/0xc)
(show_stack) from [<8033641f>] (dump_stack_lvl+0x2b/0x34)
(dump_stack_lvl) from [<803b7f3f>] (ubi_io_write+0x3ab/0x4a8)
(ubi_io_write) from [<803b817d>] (ubi_io_write_vid_hdr+0x71/0xb4)
(ubi_io_write_vid_hdr) from [<803b6971>] (ubi_eba_copy_leb+0x195/0x2f0)
(ubi_eba_copy_leb) from [<803b939b>] (wear_leveling_worker+0x2ff/0x738)
(wear_leveling_worker) from [<803b86ef>] (do_work+0x5b/0xb0)
(do_work) from [<803b9ee1>] (ubi_thread+0xb1/0x11c)
(ubi_thread) from [<8012c113>] (kthread+0x11b/0x134)
(kthread) from [<80100139>] (ret_from_fork+0x11/0x38)
Exception stack(0x80c43fb0 to 0x80c43ff8)
...
ubi0 error: ubi_dump_flash: err -16 while reading 2048 bytes from PEB
ubi0 error: wear_leveling_worker: error -16 while moving PEB 246 to PEB
ubi0 warning: ubi_ro_mode.part.0: switch to read-only mode
...
ubi0 error: do_work: work failed with error code -16
ubi0 error: ubi_thread: ubi_bgt0d: work failed with error code -16
...
Kernel panic - not syncing: Software Watchdog Timer expired
Add a reboot notification for the ubi/wear-leveling to shutdown any
potential flash work actions before the nand is suspended.
Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
The definition of ubi_destroy_ai() has been removed since
commit dac6e2087a ("UBI: Add fastmap stuff to attach.c").
Remove the empty declaration in header file.
Signed-off-by: Zhang Zekun <zhangzekun11@huawei.com>
Reviewed-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Since commit 14072ee33d ("ubi: fastmap: Check wl_pool for free peb
before wear leveling"), wear_leveling_worker() won't schedule fm_work
if wear-leveling pool is empty, which could temporarily disable the
wear-leveling until the fastmap is updated(eg. pool becomes empty).
Fix it by scheduling fm_work if wl_pool is empty during wear-leveing.
Fixes: 14072ee33d ("ubi: fastmap: Check wl_pool for free peb before wear leveling")
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
During wear-leveing work, the source PEB will be moved into scrub list
when source LEB cannot be locked in ubi_eba_copy_leb(), which is wrong
for non-scrub type source PEB. The problem could bring extra and
ineffective wear-leveing jobs, which makes more or less negative effects
for the life time of flash. Specifically, the process is divided 2 steps:
1. wear_leveling_worker // generate false scrub type PEB
ubi_eba_copy_leb // MOVE_RETRY is returned
leb_write_trylock // trylock failed
scrubbing = 1;
e1 is put into ubi->scrub
2. wear_leveling_worker // schedule false scrub type PEB for wl
scrubbing = 1
e1 = rb_entry(rb_first(&ubi->scrub))
The problem can be reproduced easily by running fsstress on a small
UBIFS partition(<64M, simulated by nandsim) for 5~10mins
(CONFIG_MTD_UBI_FASTMAP=y,CONFIG_MTD_UBI_WL_THRESHOLD=50). Following
message is shown:
ubi0: scrubbed PEB 66 (LEB 0:10), data moved to PEB 165
Since scrub type source PEB has set variable scrubbing as '1', and
variable scrubbing is checked before variable keep, so the problem can
be fixed by setting keep variable as 1 directly if the source LEB cannot
be locked.
Fixes: e801e128b2 ("UBI: fix missing scrub when there is a bit-flip")
CC: stable@vger.kernel.org
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
The default dummy cycle for Macronix SPI NOR flash in Octal Output
Read Mode(1-1-8) is 20.
Currently, the dummy buswidth is set according to the address bus width.
In the 1-1-8 mode, this means the dummy buswidth is 1. When converting
dummy cycles to bytes, this results in 20 x 1 / 8 = 2 bytes, causing the
host to read data 4 cycles too early.
Since the protocol data buswidth is always greater than or equal to the
address buswidth. Setting the dummy buswidth to match the data buswidth
increases the likelihood that the dummy cycle-to-byte conversion will be
divisible, preventing the host from reading data prematurely.
Fixes: 0e30f47232 ("mtd: spi-nor: add support for DTR protocol")
Cc: stable@vger.kernel.org
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Signed-off-by: Cheng Ming Lin <chengminglin@mxic.com.tw>
Link: https://lore.kernel.org/r/20241112075242.174010-2-linchengming884@gmail.com
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Commit d35df77707 ("mtd: spi-nor: winbond: fix w25q128 regression")
upstream fixed a regression for flavors of 0xef4018 flash that don't
define SFDP tables. Add a comment on the flash definition highlighting
that there are flavors of flashes with and without SFDP support.
It spares developers searching the entire git log for when we'll better
handle these cases.
Acked-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20241029080049.96679-1-tudor.ambarus@linaro.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
The is_bin_visible() callbacks should not modify the struct
bin_attribute passed as argument.
Enforce this by marking the argument as const.
As there are not many callback implementers perform this change
throughout the tree at once.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Jason Gunthorpe <jgg@nvidia.com>
Acked-by: Ira Weiny <ira.weiny@intel.com>
Acked-by: Krzysztof Wilczyński <kw@linux.com>
Link: https://lore.kernel.org/r/20241103-sysfs-const-bin_attr-v2-5-71110628844c@weissschuh.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In octal DTR mode, RD_ANY_REG_OP needs to use 4-byte address regardless
of flash's internal address mode. Use nor->addr_nbytes which is set to 4
during setup.
Fixes: eff9604390 ("mtd: spi-nor: spansion: add octal DTR support in RD_ANY_REG_OP")
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Link: https://lore.kernel.org/r/20241016000837.17951-1-Takahiro.Kuwano@infineon.com
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
After commit 0edb555a65 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/mtd to use .remove(), with
the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20241007205803.444994-10-u.kleine-koenig@baylibre.com
Variable ret is being assigned a value that is never read, the following
goto statement jumps to a statement that assigns ret a return from the
call to function do_write_oneword_once. The assignment is redundant
and can be removed.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20241002172258.958113-1-colin.i.king@gmail.com
'struct nand_ecc_engine_ops' are not modified in these drivers.
Constifying this structure moves some data to a read-only section, so
increases overall security, especially when the structure holds some
function pointers.
Update the prototype of mxic_ecc_get_pipelined_ops() accordingly.
On a x86_64, with allmodconfig, as an example:
Before:
======
text data bss dec hex filename
16709 1374 16 18099 46b3 drivers/mtd/nand/ecc-mxic.o
After:
=====
text data bss dec hex filename
16789 1294 16 18099 46b3 drivers/mtd/nand/ecc-mxic.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/72597e9de2320a4109be2112e696399592edacd4.1729271136.git.christophe.jaillet@wanadoo.fr
Use alphabetical order, not because it's pretty, but because it makes
sense. This way the devices are listed by density, and then by hardware
feature set. Add comments to make the list more understandable.
There is no intended functional change.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://lore.kernel.org/linux-mtd/20241009125002.191109-5-miquel.raynal@bootlin.com
The last 4 characters in Winbond's branding indicate:
- the package type (ZE/SF/TB),
- the temperature grade (I/J),
- special options, typically the continuous read vs. page read feature
support and its default (G/T/F/R),
None of these information impact us, at the software level (well, the
continuous read mode by default is impacting, but is already handled
gracefully by disabling it in the initialization phase), so let's get
rid of it.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://lore.kernel.org/linux-mtd/20241009125002.191109-4-miquel.raynal@bootlin.com
These four chips:
* W25N512GW
* W25N01GW
* W25N01JW
* W25N02JW
all require a single bit of ECC strength and thus feature an on-die
Hamming-like ECC engine. There is no point in filling a ->get_status()
callback for them because the main ECC status bytes are located in
standard places, and retrieving the number of bitflips in case of
corrected chunk is both useless and unsupported (if there are bitflips,
then there is 1 at most, so no need to query the chip for that).
Without this change, a kernel warning triggers every time a bit flips.
Fixes: 6a804fb72d ("mtd: spinand: winbond: add support for serial NAND flash")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://lore.kernel.org/linux-mtd/20241009125002.191109-3-miquel.raynal@bootlin.com
Refactor the power management handling in the gpmi nand driver. Remove
redundant pm_runtime calls in the driver probe function. Handle the pad
control and use the leverage runtime suspend and resume calls to take
care of clocks in system suspend and resume functions.
Signed-off-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20241007191319.220775-2-han.xu@nxp.com
There's no reason for this driver to be using OF-specific property
accessors. Switch to using generic device property interfaces and
replace the of.h include with property.h. This allows us to no longer
check the existence of the associated of_node.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20241007122350.75285-3-brgl@bgdev.pl
The line in nand_davinci_get_pdata() prototype is broken in a weird and
unreadable way. Make it consistent with the rest of the code.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20241007122350.75285-2-brgl@bgdev.pl
The pmecc "user" structure is allocated in atmel_pmecc_create_user() and
was supposed to be freed with atmel_pmecc_destroy_user(), but this other
helper is never called. One solution would be to find the proper
location to call the destructor, but the trend today is to switch to
device managed allocations, which in this case fits pretty well.
Replace kzalloc() by devm_kzalloc() and drop the destructor entirely.
Reported-by: "Dr. David Alan Gilbert" <linux@treblig.org>
Closes: https://lore.kernel.org/all/ZvmIvRJCf6VhHvpo@gallifrey/
Fixes: f88fc122cc ("mtd: nand: Cleanup/rework the atmel_nand driver")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20241001203149.387655-1-miquel.raynal@bootlin.com
The rpc-if-hyperflash driver can be compiled as a module, but lacks
MODULE_DEVICE_TABLE() and will therefore not be loaded automatically.
Fix this.
Fixes: 5de15b610f ("mtd: hyperbus: add Renesas RPC-IF driver")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240731080846.257139-1-biju.das.jz@bp.renesas.com
Add manufacturer ID 0xc2 at the end of ID table to allow manufacturer
fixups to be applied for any Macronix flash. This spares us of adding
new flash entries for flashes that can be initialized solely based on
the SFDP data, but still need the manufacturer hooks to set parameters
that can't be discovered at SFDP parsing time.
The ID is added in order to set the octal DTR methods. SFDP defines a
"Command Sequences to Change to Octal DDR (8D-8D-8D) Mode" which can
enable the octal DTR mode. Until that is parsed and used, use the
local defined method.
Suggested-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: JaimeLiao <jaimeliao@mxic.com.tw>
Signed-off-by: AlvinZhou <alvinzhou@mxic.com.tw>
Link: https://lore.kernel.org/r/20240926141956.2386374-7-alvinzhou.tw@gmail.com
[ta: update commit message and comment in the code]
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Substitute the inclusion of <linux/random.h> header with
<linux/prandom.h> to allow the removal of legacy inclusion
of <linux/prandom.h> from <linux/random.h>.
Signed-off-by: Uros Bizjak <ubizjak@gmail.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
Parse BFPT in order to retrieve the byte order in 8D-8D-8D mode.
This info flag will be used as a basis to determine whether
there is byte swapping of data for SPI NOR flash in octal
DTR mode.
The controller driver will check whether byte swapping is supported
to determine whether the corresponding operation are supported,
thus avoiding the generation of unexpected data order.
Merge Tudor's patch and add modifications for suiting newer version
of Linux kernel.
Reviewed-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: JaimeLiao <jaimeliao@mxic.com.tw>
Signed-off-by: AlvinZhou <alvinzhou@mxic.com.tw>
Link: https://lore.kernel.org/r/20240926141956.2386374-5-alvinzhou.tw@gmail.com
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Macronix swaps bytes on a 16-bit boundary when configured in Octal DTR.
The byte order of 16-bit words is swapped when read or written in 8D-8D-8D
mode compared to STR modes. Allow operations to specify the byte order in
DTR mode, so that controllers can swap the bytes back at run-time to
address the flash's endianness requirements, if they are capable. If the
controller is not capable of swapping the bytes, the protocol is downgrade
via spi_nor_spimem_adjust_hwcaps(). When available, the swapping of the
bytes is always done regardless if it's a data or register access, so that
it comply with the JESD216 requirements: "Byte order of 16-bit words is
swapped when read in 8D-8D-8D mode compared to 1-1-1".
Merge Tudor's patch and add modifications for suiting newer version
of Linux kernel.
Suggested-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: JaimeLiao <jaimeliao@mxic.com.tw>
Signed-off-by: AlvinZhou <alvinzhou@mxic.com.tw>
Link: https://lore.kernel.org/r/20240926141956.2386374-4-alvinzhou.tw@gmail.com
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Create Macronix specify method for enable Octal DTR mode and
set 20 dummy cycles to allow running at the maximum supported
frequency for Macronix Octal flash.
Use number of dummy cycles which is parse by SFDP then convert
it to bit pattern and set in CR2 register.
Set CR2 register for enable octal DTR mode.
Use Read ID to confirm that enabling/disabling octal DTR mode
was successful.
Macronix ID format is A-A-B-B-C-C in octal DTR mode.
To ensure the successful enablement of octal DTR mode, confirm
that the 6-byte data is entirely correct.
Co-developed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: JaimeLiao <jaimeliao@mxic.com.tw>
Signed-off-by: AlvinZhou <alvinzhou@mxic.com.tw>
Link: https://lore.kernel.org/r/20240926141956.2386374-2-alvinzhou.tw@gmail.com
no_llseek had been defined to NULL two years ago, in commit 868941b144
("fs: remove no_llseek")
To quote that commit,
At -rc1 we'll need do a mechanical removal of no_llseek -
git grep -l -w no_llseek | grep -v porting.rst | while read i; do
sed -i '/\<no_llseek\>/d' $i
done
would do it.
Unfortunately, that hadn't been done. Linus, could you do that now, so
that we could finally put that thing to rest? All instances are of the
form
.llseek = no_llseek,
so it's obviously safe.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This concludes a long journey towards replacing the old
board files with devictree description on the Cirrus Logic
EP93xx platform.
Nikita Shubin has been working on this for a long time,
for details see the last post on
https://lore.kernel.org/lkml/20240909-ep93xx-v12-0-e86ab2423d4b@maquefel.me/
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEiK/NIGsWEZVxh/FrYKtH/8kJUicFAmb1croACgkQYKtH/8kJ
UicY0g//XXEXcBgE2CLfKzGimN3gREIElEqFCpd7v32XWGIQNFdS7StiGqNx1MeU
UYdILm97ldgpx+NnHd3Cb9HbLQ1CTIIvAZ2ngFLDeeZO+wgzBVxWTrdUUp57ZIBn
5Fq0hNaR1bfqSr+J+ZbgizH5N96EvLr3OPz/eJetY7egVBUID/0OpwssPJxW1Ns0
f+W+yIc7BomVa71xGgI+RkHrG/5DSaoFtrB+ESt7q1nNUIeMn32JqBYqE0U2iCRN
ADO8I+WfAjIcO1uN5n3KM3tigZI3GKSrBdllByr8wWNbp9l5rMYfFAPEaI109iyI
7PFrB6qhAlY9LckXMNhwLyjlnWt6qrI0B+tyg+3tW6+4OwFnpPN0cIhszFPOmrhv
njsDSvybp0q9V6Mn7f394H6v9sk9RHr68mpu12hO65UBP7Qe7mrdl3snnFcm0FHL
jCLnvjdmCSqRlV6YFsKDHuDzZOG88sAwH0mySKd3c/CVvgaNDsaJduelPGpuXlXX
P7op6D8kyKFKfmwK0kz3t+3+2ozgYq3nu4amI7rJ72MOvJKBocTwwqpAesIuegde
bn3ZN30yZDTbfEFuveOAzx7rqDlZYX/tN0uspL4VBN0rdayxBng5hneV2PypTtW0
wE9ptz5qIz8AssJ7NInwpgRTDjEut4SY3m3CS2/66V08B4EznAA=
=Y3Cd
-----END PGP SIGNATURE-----
Merge tag 'soc-ep93xx-dt-6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC update from Arnd Bergmann:
"Convert ep93xx to devicetree
This concludes a long journey towards replacing the old board files
with devictree description on the Cirrus Logic EP93xx platform.
Nikita Shubin has been working on this for a long time, for details
see the last post on
https://lore.kernel.org/lkml/20240909-ep93xx-v12-0-e86ab2423d4b@maquefel.me/"
* tag 'soc-ep93xx-dt-6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (47 commits)
dt-bindings: gpio: ep9301: Add missing "#interrupt-cells" to examples
MAINTAINERS: Update EP93XX ARM ARCHITECTURE maintainer
soc: ep93xx: drop reference to removed EP93XX_SOC_COMMON config
net: cirrus: use u8 for addr to calm down sparse
dmaengine: cirrus: use snprintf() to calm down gcc 13.3.0
dmaengine: ep93xx: Fix a NULL vs IS_ERR() check in probe()
pinctrl: ep93xx: Fix raster pins typo
spi: ep93xx: update kerneldoc comments for ep93xx_spi
clk: ep93xx: Fix off by one in ep93xx_div_recalc_rate()
clk: ep93xx: add module license
dmaengine: cirrus: remove platform code
ASoC: cirrus: edb93xx: Delete driver
ARM: ep93xx: soc: drop defines
ARM: ep93xx: delete all boardfiles
ata: pata_ep93xx: remove legacy pinctrl use
pwm: ep93xx: drop legacy pinctrl
ARM: ep93xx: DT for the Cirrus ep93xx SoC platforms
ARM: dts: ep93xx: Add EDB9302 DT
ARM: dts: ep93xx: add ts7250 board
ARM: dts: add Cirrus EP93XX SoC .dtsi
...
Quite a lot of nilfs2 work this time around.
Notable patch series in this pull request are:
"mul_u64_u64_div_u64: new implementation" by Nicolas Pitre, with
assistance from Uwe Kleine-König. Reimplement mul_u64_u64_div_u64() to
provide (much) more accurate results. The current implementation was
causing Uwe some issues in the PWM drivers.
"xz: Updates to license, filters, and compression options" from Lasse
Collin. Miscellaneous maintenance and kinor feature work to the xz
decompressor.
"Fix some GDB command error and add some GDB commands" from Kuan-Ying Lee.
Fixes and enhancements to the gdb scripts.
"treewide: add missing MODULE_DESCRIPTION() macros" from Jeff Johnson.
Adds lots of MODULE_DESCRIPTIONs, thus fixing lots of warnings about this.
"nilfs2: add support for some common ioctls" from Ryusuke Konishi. Adds
various commonly-available ioctls to nilfs2.
"This series fixes a number of formatting issues in kernel doc comments"
from Ryusuke Konishi does that.
"nilfs2: prevent unexpected ENOENT propagation" from Ryusuke Konishi. Fix
issues where -ENOENT was being unintentionally and inappropriately
returned to userspace.
"nilfs2: assorted cleanups" from Huang Xiaojia.
"nilfs2: fix potential issues with empty b-tree nodes" from Ryusuke
Konishi fixes some issues which can occur on corrupted nilfs2 filesystems.
"scripts/decode_stacktrace.sh: improve error reporting and usability" from
Luca Ceresoli does those things.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCZu7dpAAKCRDdBJ7gKXxA
jsPqAPwMDEZyKlfSw7QioEHNHDkmkbP7VYCYR0CbUnppbztwpAD8D37aVbWQ+UzM
3nnOq3W2Pc2o/20zqi8Upf1mnvUrygQ=
=/NWE
-----END PGP SIGNATURE-----
Merge tag 'mm-nonmm-stable-2024-09-21-07-52' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull non-MM updates from Andrew Morton:
"Many singleton patches - please see the various changelogs for
details.
Quite a lot of nilfs2 work this time around.
Notable patch series in this pull request are:
- "mul_u64_u64_div_u64: new implementation" by Nicolas Pitre, with
assistance from Uwe Kleine-König. Reimplement mul_u64_u64_div_u64()
to provide (much) more accurate results. The current implementation
was causing Uwe some issues in the PWM drivers.
- "xz: Updates to license, filters, and compression options" from
Lasse Collin. Miscellaneous maintenance and kinor feature work to
the xz decompressor.
- "Fix some GDB command error and add some GDB commands" from
Kuan-Ying Lee. Fixes and enhancements to the gdb scripts.
- "treewide: add missing MODULE_DESCRIPTION() macros" from Jeff
Johnson. Adds lots of MODULE_DESCRIPTIONs, thus fixing lots of
warnings about this.
- "nilfs2: add support for some common ioctls" from Ryusuke Konishi.
Adds various commonly-available ioctls to nilfs2.
- "This series fixes a number of formatting issues in kernel doc
comments" from Ryusuke Konishi does that.
- "nilfs2: prevent unexpected ENOENT propagation" from Ryusuke
Konishi. Fix issues where -ENOENT was being unintentionally and
inappropriately returned to userspace.
- "nilfs2: assorted cleanups" from Huang Xiaojia.
- "nilfs2: fix potential issues with empty b-tree nodes" from Ryusuke
Konishi fixes some issues which can occur on corrupted nilfs2
filesystems.
- "scripts/decode_stacktrace.sh: improve error reporting and
usability" from Luca Ceresoli does those things"
* tag 'mm-nonmm-stable-2024-09-21-07-52' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (103 commits)
list: test: increase coverage of list_test_list_replace*()
list: test: fix tests for list_cut_position()
proc: use __auto_type more
treewide: correct the typo 'retun'
ocfs2: cleanup return value and mlog in ocfs2_global_read_info()
nilfs2: remove duplicate 'unlikely()' usage
nilfs2: fix potential oob read in nilfs_btree_check_delete()
nilfs2: determine empty node blocks as corrupted
nilfs2: fix potential null-ptr-deref in nilfs_btree_insert()
user_namespace: use kmemdup_array() instead of kmemdup() for multiple allocation
tools/mm: rm thp_swap_allocator_test when make clean
squashfs: fix percpu address space issues in decompressor_multi_percpu.c
lib: glob.c: added null check for character class
nilfs2: refactor nilfs_segctor_thread()
nilfs2: use kthread_create and kthread_stop for the log writer thread
nilfs2: remove sc_timer_task
nilfs2: do not repair reserved inode bitmap in nilfs_new_inode()
nilfs2: eliminate the shared counter and spinlock for i_generation
nilfs2: separate inode type information from i_state field
nilfs2: use the BITS_PER_LONG macro
...
string:
- add mem_is_zero()
core:
- support more device numbers
- use XArray for minor ids
- add backlight constants
- Split dma fence array creation into alloc and arm
fbdev:
- remove usage of old fbdev hooks
kms:
- Add might_fault() to drm_modeset_lock priming
- Add dynamic per-crtc vblank configuration support
dma-buf:
- docs cleanup
buddy:
- Add start address support for trim function
printk:
- pass description to kmsg_dump
scheduler;
- Remove full_recover from drm_sched_start
ttm:
- Make LRU walk restartable after dropping locks
- Allow direct reclaim to allocate local memory
panic:
- add display QR code (in rust)
displayport:
- mst: GUID improvements
bridge:
- Silence error message on -EPROBE_DEFER
- analogix: Clean aup
- bridge-connector: Fix double free
- lt6505: Disable interrupt when powered off
- tc358767: Make default DP port preemphasis configurable
- lt9611uxc: require DRM_BRIDGE_ATTACH_NO_CONNECTOR
- anx7625: simplify OF array handling
- dw-hdmi: simplify clock handling
- lontium-lt8912b: fix mode validation
- nwl-dsi: fix mode vsync/hsync polarity
xe:
- Enable LunarLake and Battlemage support
- Introducing Xe2 ccs modifiers for integrated and discrete graphics
- rename xe perf to xe observation
- use wb caching on DGFX for system memory
- add fence timeouts
- Lunar Lake graphics/media/display workarounds
- Battlemage workarounds
- Battlemage GSC support
- GSC and HuC fw updates for LL/BM
- use dma_fence_chain_free
- refactor hw engine lookup and mmio access
- enable priority mem read for Xe2
- Add first GuC BMG fw
- fix dma-resv lock
- Fix DGFX display suspend/resume
- Use xe_managed for kernel BOs
- Use reserved copy engine for user binds on faulting devices
- Allow mixing dma-fence jobs and long-running faulting jobs
- fix media TLB invalidation
- fix rpm in TTM swapout path
- track resources and VF state by PF
i915:
- Type-C programming fix for MTL+
- FBC cleanup
- Calc vblank delay more accurately
- On DP MST, Enable LT fallback for UHBR<->non-UHBR rates
- Fix DP LTTPR detection
- limit relocations to INT_MAX
- fix long hangs in buddy allocator on DG2/A380
amdgpu:
- Per-queue reset support
- SDMA devcoredump support
- DCN 4.0.1 updates
- GFX12/VCN4/JPEG4 updates
- Convert vbios embedded EDID to drm_edid
- GFX9.3/9.4 devcoredump support
- process isolation framework for GFX 9.4.3/4
- take IOMMU mappings into account for P2P DMA
amdkfd:
- CRIU fixes
- HMM fix
- Enable process isolation support for GFX 9.4.3/4
- Allow users to target recommended SDMA engines
- KFD support for targetting queues on recommended SDMA engines
radeon:
- remove .load and drm_dev_alloc
- Fix vbios embedded EDID size handling
- Convert vbios embedded EDID to drm_edid
- Use GEM references instead of TTM
- r100 cp init cleanup
- Fix potential overflows in evergreen CS offset tracking
msm:
- DPU:
- implement DP/PHY mapping on SC8180X
- Enable writeback on SM8150, SC8180X, SM6125, SM6350
- DP:
- Enable widebus on all relevant chipsets
- MSM8998 HDMI support
- GPU:
- A642L speedbin support
- A615/A306/A621 support
- A7xx devcoredump support
ast:
- astdp: Support AST2600 with VGA
- Clean up HPD
- Fix timeout loop for DP link training
- reorganize output code by type (VGA, DP, etc)
- convert to struct drm_edid
- fix BMC handling for all outputs
exynos:
- drop stale MAINTAINERS pattern
- constify struct
loongson:
- use GEM refcount over TTM
mgag200:
- Improve BMC handling
- Support VBLANK intterupts
- transparently support BMC outputs
nouveau:
- Refactor and clean up internals
- Use GEM refcount over TTM's
gm12u320:
- convert to struct drm_edid
gma500:
- update i2c terms
lcdif:
- pixel clock fix
host1x:
- fix syncpoint IRQ during resume
- use iommu_paging_domain_alloc()
imx:
- ipuv3: convert to struct drm_edid
omapdrm:
- improve error handling
- use common helper for_each_endpoint_of_node()
panel:
- add support for BOE TV101WUM-LL2 plus DT bindings
- novatek-nt35950: improve error handling
- nv3051d: improve error handling
- panel-edp: add support for BOE NE140WUM-N6G; revert support for
SDC ATNA45AF01
- visionox-vtdr6130: improve error handling; use
devm_regulator_bulk_get_const()
- boe-th101mb31ig002: Support for starry-er88577 MIPI-DSI panel plus
DT; Fix porch parameter
- edp: Support AOU B116XTN02.3, AUO B116XAN06.1, AOU B116XAT04.1,
BOE NV140WUM-N41, BOE NV133WUM-N63, BOE NV116WHM-A4D, CMN N116BCA-EA2,
CMN N116BCP-EA2, CSW MNB601LS1-4
- himax-hx8394: Support Microchip AC40T08A MIPI Display panel plus DT
- ilitek-ili9806e: Support Densitron DMT028VGHMCMI-1D TFT plus DT
- jd9365da: Support Melfas lmfbx101117480 MIPI-DSI panel plus DT; Refactor
for code sharing
- panel-edp: fix name for HKC MB116AN01
- jd9365da: fix "exit sleep" commands
- jdi-fhd-r63452: simplify error handling with DSI multi-style
helpers
- mantix-mlaf057we51: simplify error handling with DSI multi-style
helpers
- simple:
support Innolux G070ACE-LH3 plus DT bindings
support On Tat Industrial Company KD50G21-40NT-A1 plus DT bindings
- st7701:
decouple DSI and DRM code
add SPI support
support Anbernic RG28XX plus DT bindings
mediatek:
- support alpha blending
- remove cl in struct cmdq_pkt
- ovl adaptor fix
- add power domain binding for mediatek DPI controller
renesas:
- rz-du: add support for RZ/G2UL plus DT bindings
rockchip:
- Improve DP sink-capability reporting
- dw_hdmi: Support 4k@60Hz
- vop: Support RGB display on Rockchip RK3066; Support 4096px width
sti:
- convert to struct drm_edid
stm:
- Avoid UAF wih managed plane and CRTC helpers
- Fix module owner
- Fix error handling in probe
- Depend on COMMON_CLK
- ltdc: Fix transparency after disabling plane; Remove unused interrupt
tegra:
- gr3d: improve PM domain handling
- convert to struct drm_edid
- Call drm_atomic_helper_shutdown()
vc4:
- fix PM during detect
- replace DRM_ERROR() with drm_error()
- v3d: simplify clock retrieval
v3d:
- Clean up perfmon
virtio:
- add DRM capset
-----BEGIN PGP SIGNATURE-----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=7jR+
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2024-09-19' of https://gitlab.freedesktop.org/drm/kernel
Pull drm updates from Dave Airlie:
"This adds a couple of patches outside the drm core, all should be
acked appropriately, the string and pstore ones are the main ones that
come to mind.
Otherwise it's the usual drivers, xe is getting enabled by default on
some new hardware, we've changed the device number handling to allow
more devices, and we added some optional rust code to create QR codes
in the panic handler, an idea first suggested I think 10 years ago :-)
string:
- add mem_is_zero()
core:
- support more device numbers
- use XArray for minor ids
- add backlight constants
- Split dma fence array creation into alloc and arm
fbdev:
- remove usage of old fbdev hooks
kms:
- Add might_fault() to drm_modeset_lock priming
- Add dynamic per-crtc vblank configuration support
dma-buf:
- docs cleanup
buddy:
- Add start address support for trim function
printk:
- pass description to kmsg_dump
scheduler:
- Remove full_recover from drm_sched_start
ttm:
- Make LRU walk restartable after dropping locks
- Allow direct reclaim to allocate local memory
panic:
- add display QR code (in rust)
displayport:
- mst: GUID improvements
bridge:
- Silence error message on -EPROBE_DEFER
- analogix: Clean aup
- bridge-connector: Fix double free
- lt6505: Disable interrupt when powered off
- tc358767: Make default DP port preemphasis configurable
- lt9611uxc: require DRM_BRIDGE_ATTACH_NO_CONNECTOR
- anx7625: simplify OF array handling
- dw-hdmi: simplify clock handling
- lontium-lt8912b: fix mode validation
- nwl-dsi: fix mode vsync/hsync polarity
xe:
- Enable LunarLake and Battlemage support
- Introducing Xe2 ccs modifiers for integrated and discrete graphics
- rename xe perf to xe observation
- use wb caching on DGFX for system memory
- add fence timeouts
- Lunar Lake graphics/media/display workarounds
- Battlemage workarounds
- Battlemage GSC support
- GSC and HuC fw updates for LL/BM
- use dma_fence_chain_free
- refactor hw engine lookup and mmio access
- enable priority mem read for Xe2
- Add first GuC BMG fw
- fix dma-resv lock
- Fix DGFX display suspend/resume
- Use xe_managed for kernel BOs
- Use reserved copy engine for user binds on faulting devices
- Allow mixing dma-fence jobs and long-running faulting jobs
- fix media TLB invalidation
- fix rpm in TTM swapout path
- track resources and VF state by PF
i915:
- Type-C programming fix for MTL+
- FBC cleanup
- Calc vblank delay more accurately
- On DP MST, Enable LT fallback for UHBR<->non-UHBR rates
- Fix DP LTTPR detection
- limit relocations to INT_MAX
- fix long hangs in buddy allocator on DG2/A380
amdgpu:
- Per-queue reset support
- SDMA devcoredump support
- DCN 4.0.1 updates
- GFX12/VCN4/JPEG4 updates
- Convert vbios embedded EDID to drm_edid
- GFX9.3/9.4 devcoredump support
- process isolation framework for GFX 9.4.3/4
- take IOMMU mappings into account for P2P DMA
amdkfd:
- CRIU fixes
- HMM fix
- Enable process isolation support for GFX 9.4.3/4
- Allow users to target recommended SDMA engines
- KFD support for targetting queues on recommended SDMA engines
radeon:
- remove .load and drm_dev_alloc
- Fix vbios embedded EDID size handling
- Convert vbios embedded EDID to drm_edid
- Use GEM references instead of TTM
- r100 cp init cleanup
- Fix potential overflows in evergreen CS offset tracking
msm:
- DPU:
- implement DP/PHY mapping on SC8180X
- Enable writeback on SM8150, SC8180X, SM6125, SM6350
- DP:
- Enable widebus on all relevant chipsets
- MSM8998 HDMI support
- GPU:
- A642L speedbin support
- A615/A306/A621 support
- A7xx devcoredump support
ast:
- astdp: Support AST2600 with VGA
- Clean up HPD
- Fix timeout loop for DP link training
- reorganize output code by type (VGA, DP, etc)
- convert to struct drm_edid
- fix BMC handling for all outputs
exynos:
- drop stale MAINTAINERS pattern
- constify struct
loongson:
- use GEM refcount over TTM
mgag200:
- Improve BMC handling
- Support VBLANK intterupts
- transparently support BMC outputs
nouveau:
- Refactor and clean up internals
- Use GEM refcount over TTM's
gm12u320:
- convert to struct drm_edid
gma500:
- update i2c terms
lcdif:
- pixel clock fix
host1x:
- fix syncpoint IRQ during resume
- use iommu_paging_domain_alloc()
imx:
- ipuv3: convert to struct drm_edid
omapdrm:
- improve error handling
- use common helper for_each_endpoint_of_node()
panel:
- add support for BOE TV101WUM-LL2 plus DT bindings
- novatek-nt35950: improve error handling
- nv3051d: improve error handling
- panel-edp:
- add support for BOE NE140WUM-N6G
- revert support for SDC ATNA45AF01
- visionox-vtdr6130:
- improve error handling
- use devm_regulator_bulk_get_const()
- boe-th101mb31ig002:
- Support for starry-er88577 MIPI-DSI panel plus DT
- Fix porch parameter
- edp: Support AOU B116XTN02.3, AUO B116XAN06.1, AOU B116XAT04.1, BOE
NV140WUM-N41, BOE NV133WUM-N63, BOE NV116WHM-A4D, CMN N116BCA-EA2,
CMN N116BCP-EA2, CSW MNB601LS1-4
- himax-hx8394: Support Microchip AC40T08A MIPI Display panel plus DT
- ilitek-ili9806e: Support Densitron DMT028VGHMCMI-1D TFT plus DT
- jd9365da:
- Support Melfas lmfbx101117480 MIPI-DSI panel plus DT
- Refactor for code sharing
- panel-edp: fix name for HKC MB116AN01
- jd9365da: fix "exit sleep" commands
- jdi-fhd-r63452: simplify error handling with DSI multi-style
helpers
- mantix-mlaf057we51: simplify error handling with DSI multi-style
helpers
- simple:
- support Innolux G070ACE-LH3 plus DT bindings
- support On Tat Industrial Company KD50G21-40NT-A1 plus DT
bindings
- st7701:
- decouple DSI and DRM code
- add SPI support
- support Anbernic RG28XX plus DT bindings
mediatek:
- support alpha blending
- remove cl in struct cmdq_pkt
- ovl adaptor fix
- add power domain binding for mediatek DPI controller
renesas:
- rz-du: add support for RZ/G2UL plus DT bindings
rockchip:
- Improve DP sink-capability reporting
- dw_hdmi: Support 4k@60Hz
- vop:
- Support RGB display on Rockchip RK3066
- Support 4096px width
sti:
- convert to struct drm_edid
stm:
- Avoid UAF wih managed plane and CRTC helpers
- Fix module owner
- Fix error handling in probe
- Depend on COMMON_CLK
- ltdc:
- Fix transparency after disabling plane
- Remove unused interrupt
tegra:
- gr3d: improve PM domain handling
- convert to struct drm_edid
- Call drm_atomic_helper_shutdown()
vc4:
- fix PM during detect
- replace DRM_ERROR() with drm_error()
- v3d: simplify clock retrieval
v3d:
- Clean up perfmon
virtio:
- add DRM capset"
* tag 'drm-next-2024-09-19' of https://gitlab.freedesktop.org/drm/kernel: (1326 commits)
drm/xe: Fix missing conversion to xe_display_pm_runtime_resume
drm/xe/xe2hpg: Add Wa_15016589081
drm/xe: Don't keep stale pointer to bo->ggtt_node
drm/xe: fix missing 'xe_vm_put'
drm/xe: fix build warning with CONFIG_PM=n
drm/xe: Suppress missing outer rpm protection warning
drm/xe: prevent potential UAF in pf_provision_vf_ggtt()
drm/amd/display: Add all planes on CRTC to state for overlay cursor
drm/i915/bios: fix printk format width
drm/i915/display: Fix BMG CCS modifiers
drm/amdgpu: get rid of bogus includes of fdtable.h
drm/amdkfd: CRIU fixes
drm/amdgpu: fix a race in kfd_mem_export_dmabuf()
drm: new helper: drm_gem_prime_handle_to_dmabuf()
drm/amdgpu/atomfirmware: Silence UBSAN warning
drm/amdgpu: Fix kdoc entry in 'amdgpu_vm_cpu_prepare'
drm/amd/amdgpu: apply command submission parser for JPEG v1
drm/amd/amdgpu: apply command submission parser for JPEG v2+
drm/amd/pm: fix the pp_dpm_pcie issue on smu v14.0.2/3
drm/amd/pm: update the features set on smu v14.0.2/3
...
The use of for_each_child_of_node_scoped() has been spread into the
subsystem drivers. Aside from that, a couple of exit path have been
fixed (mtk, denali), the TI GPMC bindings have been enhanced to comply
with up-to-date partition descriptions and as always there is a load of
small and misc fixes.
* SPI-NAND changes
The most impacting series this cycle is bringing support for continuous
reads in the SPI-NAND subsystem. This is a feature already merged in the
raw NAND subsystem which allows optimizing the internal fetch times in
the chip while reading sequential pages within an eraseblock. For now
only Macronix NANDs benefit from this feature. While we are talking
about Macronix, some of their chip need an explicit action for selecting
a different plane, and support for it has also been brought.
The bitflip threshold has also been set to the same arbitrary level as
in the raw NAND subsystem to optimize wear leveling decisions, and
finally support for a new Winbond chip has been added.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmbkfEYACgkQJWrqGEe9
VoT9TAgAsJZeCITvQfCBcaBScr8O86eqynvwkkfltdK8kcdCtH7P3gR9XvMmOOq8
QY8Ru072ufTj0dwT+YnWlRZ0jopK2Kd8JB41jYm4pP3euSUyIm+gf5d7AbHoWlLm
J6HfvnDNzEO0Fixpj3hqFKCDr1Xt0jWzVLh/ZyNa+0co/oJi0w0lnWxIs/iCgBQ2
sSosVhc0X0kt7RhV8RFvyIu3i9k3MFzKYt6hP07PpAVxlshvWHLOnU27FiIhGioz
UGwasbZ2XLbOZhcGaK9Q+cCrMZn52zJI8inlLKBFizU1+eUz4Q1kCVnx0OiPz7uW
7NyiiOUjPpJCrkKpWZbUnV3C2lZQOg==
=Xg6Q
-----END PGP SIGNATURE-----
Merge tag 'nand/for-6.12' into mtd/next
* Raw NAND changes
The use of for_each_child_of_node_scoped() has been spread into the
subsystem drivers. Aside from that, a couple of exit path have been
fixed (mtk, denali), the TI GPMC bindings have been enhanced to comply
with up-to-date partition descriptions and as always there is a load of
small and misc fixes.
* SPI-NAND changes
The most impacting series this cycle is bringing support for continuous
reads in the SPI-NAND subsystem. This is a feature already merged in the
raw NAND subsystem which allows optimizing the internal fetch times in
the chip while reading sequential pages within an eraseblock. For now
only Macronix NANDs benefit from this feature. While we are talking
about Macronix, some of their chip need an explicit action for selecting
a different plane, and support for it has also been brought.
The bitflip threshold has also been set to the same arbitrary level as
in the raw NAND subsystem to optimize wear leveling decisions, and
finally support for a new Winbond chip has been added.
Notable changes:
- Add Write Protect support for N25Q064A.
- New flash support for Zetta ZD25Q128C and Spansion S28HS256T.
- Fix a NULL dereference in probe path for flashes without a name. The
probe path tries to access the name without checking its existence
first. S28HS256T is the first flash to define its entry without a
name, uncovering this issue.
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQQTlUWNzXGEo3bFmyIR4drqP028CQUCZuWyzBQccHJhdHl1c2hA
a2VybmVsLm9yZwAKCRAR4drqP028CXj6AQCvucu8Z8Z2WDwvpn51GGNOSmgIfHkJ
i02EIQW5Cz3dygEA7pVZYyW1M/IfbgauX/NI/eYoEFwDfMD5t+MJ4HId+wY=
=F9Ud
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-6.12' into mtd/next
SPI NOR changes for 6.12
Notable changes:
- Add Write Protect support for N25Q064A.
- New flash support for Zetta ZD25Q128C and Spansion S28HS256T.
- Fix a NULL dereference in probe path for flashes without a name. The
probe path tries to access the name without checking its existence
first. S28HS256T is the first flash to define its entry without a
name, uncovering this issue.
Fix flash probing by name. Flash entries without a name are allowed
since commit 15eb8303bb ("mtd: spi-nor: mark the flash name as
obsolete"). But it was just until recently that a flash entry without a
name was actually introduced. This triggers a bug in the legacy probe by
name path. Skip entries without a name to fix it.
Fixes: 2095e7da8049 ("mtd: spi-nor: spansion: Add support for S28HS256T")
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Closes: https://lore.kernel.org/r/66c8ebb0-1324-4ad9-9926-8d4eb7e1e63a@nvidia.com/
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20240909072854.812206-1-mwalle@kernel.org
These flash chips are used on Google / TP-Link / ASUS OnHub devices, and
OnHub devices are write-protected by default (same as any other
ChromeOS/Chromebook system). I've referred to datasheets, and tested on
OnHub devices.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20240726185825.142733-1-computersforpeace@gmail.com
Writing to the Flash in `sst_nor_write()` is a 3-step process:
first an optional one-byte write to get 2-byte-aligned, then the
bulk of the data is written out in vendor-specific 2-byte writes.
Finally, if there's a byte left over, another one-byte write.
This was implemented 3 times in the body of `sst_nor_write()`.
To reduce code duplication, factor out these sub-steps to their
own function.
Signed-off-by: Csókás, Bence <csokas.bence@prolan.hu>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
[pratyush@kernel.org: fixup whitespace, use %zu instead of %i in WARN()]
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20240710091401.1282824-1-csokas.bence@prolan.hu
Macronix serial NAND flash with a two-plane structure requires
insertion of the Plane Select bit into the column address during
the write_to_cache operation.
Additionally, for MX35{U,F}2G14AC and MX35LF2GE4AB, insertion of
the Plane Select bit into the column address is required during
the read_from_cache operation.
Signed-off-by: Cheng Ming Lin <chengminglin@mxic.com.tw>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240909092643.2434479-3-linchengming884@gmail.com
Add two flags for inserting the Plane Select bit into the column
address during the write_to_cache and the read_from_cache operation.
Add the SPINAND_HAS_PROG_PLANE_SELECT_BIT flag for serial NAND flash
that require inserting the Plane Select bit into the column address
during the write_to_cache operation.
Add the SPINAND_HAS_READ_PLANE_SELECT_BIT flag for serial NAND flash
that require inserting the Plane Select bit into the column address
during the read_from_cache operation.
Signed-off-by: Cheng Ming Lin <chengminglin@mxic.com.tw>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240909092643.2434479-2-linchengming884@gmail.com
Reviewing a series converting the for_each_chil_of_node() loops into
their _scoped variants made me realize there was no cleanup of the
already registered NAND devices upon error which may leak memory on
systems with more than a chip when this error occurs. We should call the
_nand_chips_cleanup() function when this happens.
Fixes: 1d6b1e4649 ("mtd: mediatek: driver for MTK Smart Device")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Reviewed-by: Matthias Brugger <matthias.bgg@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20240826153019.67106-2-miquel.raynal@bootlin.com
devm_kasprintf() can return a NULL pointer on failure but this
returned value is not checked.
Fixes: acfe63ec1c ("mtd: Convert to using %pOFn instead of device_node.name")
Signed-off-by: Charles Han <hanchunchao@inspur.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240828092427.128177-1-hanchunchao@inspur.com
There are some un-freed resources in one of the error path which would
benefit from a helper going through all the registered mtk chips one by
one and perform all the necessary cleanup. This is precisely what the
remove path does, so let's extract the logic in a helper.
There is no functional change.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Reviewed-by: Matthias Brugger <matthias.bgg@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20240826153019.67106-1-miquel.raynal@bootlin.com
Like for other atmel drivers (serial, crypto, mmc, …), too.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240828063707.73869-1-ada@thorsis.com
There is a reason why sometime we write "NAND chip" with an 's'. It
usually means several chips can be managed by the same controller. So
when initializing a single chip at a time, the wording "chip" must be
used, otherwise when talking about all the chips managed by the
controller, we want to use "chips". Fix the function name to clarify the
meson_nfc_nand_chip*s*_cleanup() helper intend.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20240826153158.67334-1-miquel.raynal@bootlin.com
Enabling continuous read support implies several changes which must be
done atomically in order to keep the code base consistent and
bisectable.
1/ Retrieving bitflips differently
Improve the helper retrieving the number of bitflips to support the case
where many pages have been read instead of just one. In this case, if
there is one page with bitflips, we cannot know the detail and just get
the information of the maximum number of bitflips corrected in the most
corrupted chunk. Compatible Macronix flashes return:
- the ECC status for the last page read (bits 0-3),
- the amount of bitflips for the whole read operation (bits 4-7).
Hence, when reading two consecutive pages, if there was 2 bits corrected
at most in one chunk, we return this amount times (arbitrary) the number
read pages. It is probably a very pessimistic calculation in most cases,
but still less pessimistic than if we multiplied this amount by the
number of chunks. Anyway, this is just for statistics, the important
data is the maximum amount of bitflips, which leads to wear leveling.
2/ Configuring, enabling and disabling the feature
Create an init function for allocating a vendor structure. Use this
vendor structure to cache the internal continuous read state. The state
is being used to discriminate between the two bitflips retrieval
methods. Finally, helpers for enabling and disabling sequential reads
are also created.
3/ Fill the chips table
Flag all the chips supporting the feature with the ->set_cont_read()
helper.
In order to validate the changes, I modified the mtd-utils test suite
with extended versions of nandbiterrs, nanddump and flash_speed in order
to support, test and benchmark continuous reads. I also ran all the UBI
tests successfully.
The nandbiterrs tool allows to track the ECC efficiency and
feedback. Here is its default output (stripped):
Successfully corrected 0 bit errors per subpage
Read reported 1 corrected bit errors
Successfully corrected 1 bit errors per subpage
Read reported 2 corrected bit errors
Successfully corrected 2 bit errors per subpage
Read reported 3 corrected bit errors
Successfully corrected 3 bit errors per subpage
Read reported 4 corrected bit errors
Successfully corrected 4 bit errors per subpage
Read reported 5 corrected bit errors
Successfully corrected 5 bit errors per subpage
Read reported 6 corrected bit errors
Successfully corrected 6 bit errors per subpage
Read reported 7 corrected bit errors
Successfully corrected 7 bit errors per subpage
Read reported 8 corrected bit errors
Successfully corrected 8 bit errors per subpage
Failed to recover 1 bitflips
Read error after 9 bit errors per page
The output using the continuous option over two pages (the second page
is kept intact):
Successfully corrected 0 bit errors per subpage
Read reported 2 corrected bit errors
Successfully corrected 1 bit errors per subpage
Read reported 4 corrected bit errors
Successfully corrected 2 bit errors per subpage
Read reported 6 corrected bit errors
Successfully corrected 3 bit errors per subpage
Read reported 8 corrected bit errors
Successfully corrected 4 bit errors per subpage
Read reported 10 corrected bit errors
Successfully corrected 5 bit errors per subpage
Read reported 12 corrected bit errors
Successfully corrected 6 bit errors per subpage
Read reported 14 corrected bit errors
Successfully corrected 7 bit errors per subpage
Read reported 16 corrected bit errors
Successfully corrected 8 bit errors per subpage
Failed to recover 1 bitflips
Read error after 9 bit errors per page
Regarding the throughput improvements, tests have been conducted in
1-1-1 and 1-1-4 modes, reading a full block X pages at a
time, X ranging from 1 to 64 (size of a block with the tested device).
The percent value on the right is the comparison of the same test
conducted without the continuous read feature, ie. reading X pages in
one single user request, which got naturally split by the core whit the
continuous read optimization disabled into single-page reads.
* 1-1-1 result:
1 page read speed is 2634 KiB/s
2 page read speed is 2704 KiB/s (+3%)
3 page read speed is 2747 KiB/s (+5%)
4 page read speed is 2804 KiB/s (+7%)
5 page read speed is 2782 KiB/s
6 page read speed is 2826 KiB/s
7 page read speed is 2834 KiB/s
8 page read speed is 2821 KiB/s
9 page read speed is 2846 KiB/s
10 page read speed is 2819 KiB/s
11 page read speed is 2871 KiB/s (+10%)
12 page read speed is 2823 KiB/s
13 page read speed is 2880 KiB/s
14 page read speed is 2842 KiB/s
15 page read speed is 2862 KiB/s
16 page read speed is 2837 KiB/s
32 page read speed is 2879 KiB/s
64 page read speed is 2842 KiB/s
* 1-1-4 result:
1 page read speed is 7562 KiB/s
2 page read speed is 8904 KiB/s (+15%)
3 page read speed is 9655 KiB/s (+25%)
4 page read speed is 10118 KiB/s (+30%)
5 page read speed is 10084 KiB/s
6 page read speed is 10300 KiB/s
7 page read speed is 10434 KiB/s (+35%)
8 page read speed is 10406 KiB/s
9 page read speed is 10769 KiB/s (+40%)
10 page read speed is 10666 KiB/s
11 page read speed is 10757 KiB/s
12 page read speed is 10835 KiB/s
13 page read speed is 10976 KiB/s
14 page read speed is 11200 KiB/s
15 page read speed is 11009 KiB/s
16 page read speed is 11082 KiB/s
32 page read speed is 11352 KiB/s (+45%)
64 page read speed is 11403 KiB/s
This work has received support and could be achieved thanks to
Alvin Zhou <alvinzhou@mxic.com.tw>.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240826101412.20644-10-miquel.raynal@bootlin.com
Macronix SPI-NANDs encode the ECC status into two bits. There are three
standard situations (no bitflip, bitflips, error), and an additional
possible situation which is only triggered when configuring the 0x10
configuration register, allowing to know, if there have been bitflips,
whether the maximum amount of bitflips was above a configurable
threshold or not. In all cases, for now, s this configuration register
is unset, it means the same as "there are bitflips".
This value is maybe standard, maybe not. For now, let's define it in the
Macronix driver, we can safely move it to a shared place later if that
is relevant.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240826101412.20644-9-miquel.raynal@bootlin.com
With GET_STATUS commands, SPI-NAND devices can tell the status of the
last read operation, in particular if there was:
- no bitflips
- corrected bitflips
- uncorrectable bitflips
The next step then to read an ECC status register and retrieve the
amount of bitflips, when relevant, if possible. The logic used here
works well for now, but will no longer apply to continuous reads. In
order to prepare the introduction of continuous reads, let's factorize
out the code that is specific to single-page reads.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240826101412.20644-8-miquel.raynal@bootlin.com
Use "macronix_" instead of "mx35lf1ge4ab_" as common prefix for the
->get_status() callback name. This callback is used by many different
families, there is no variation in the implementation so far.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240826101412.20644-7-miquel.raynal@bootlin.com
This helper function will soon be used from a vendor driver, let's
export it through the spinand.h header. No need for any export, as there
is currently no reason for any module to need it.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240826101412.20644-6-miquel.raynal@bootlin.com
A regular page read consist in:
- Asking one page of content from the NAND array to be loaded in the
chip's SRAM,
- Waiting for the operation to be done,
- Retrieving the data (I/O phase) from the chip's SRAM.
When reading several sequential pages, the above operation is repeated
over and over. There is however a way to optimize these accesses, by
enabling continuous reads. The feature requires the NAND chip to have a
second internal SRAM area plus a bit of additional internal logic to
trigger another internal transfer between the NAND array and the second
SRAM area while the I/O phase is ongoing. Once the first I/O phase is
done, the host can continue reading more data, continuously, as the chip
will automatically switch to the second SRAM content (which has already
been loaded) and in turns trigger the next load into the first SRAM area
again.
From an instruction perspective, the command op-codes are different, but
the same cycles are required. The only difference is that after a
continuous read (which is stopped by a CS deassert), the host must
observe a delay of tRST. However, because there is no guarantee in Linux
regarding the actual state of the CS pin after a transfer (in order to
speed-up the next transfer if targeting the same device), it was
necessary to manually end the continuous read with a configuration
register write operation.
Continuous reads have two main drawbacks:
* They only work on full pages (column address ignored)
* Only the main data area is pulled, out-of-band bytes are not
accessible. Said otherwise, the feature can only be useful with on-die
ECC engines.
Performance wise, measures have been performed on a Zynq platform using
Macronix SPI-NAND controller with a Macronix chip (based on the
flash_speed tool modified for testing sequential reads):
- 1-1-1 mode: performances improved from +3% (2-pages) up to +10% after
a dozen pages.
- 1-1-4 mode: performances improved from +15% (2-pages) up to +40% after
a dozen pages.
This series is based on a previous work from Macronix engineer Jaime
Liao.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20240826101412.20644-5-miquel.raynal@bootlin.com
There is currently only a single path for performing page reads as
requested by the MTD layer. Soon there will be two:
- a "regular" page read
- a continuous page read
Let's extract the page read logic in a dedicated helper, so the
introduction of continuous page reads will be as easy as checking whether
continuous reads shall/can be used and calling one helper or the other.
There is not behavioral change intended.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240826101412.20644-4-miquel.raynal@bootlin.com
Avoids the need for manual cleanup of_node_put() in early exits
from the loop.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240826094328.2991664-9-ruanjinjie@huawei.com
The devm_clk_get_enabled() helper:
- calls devm_clk_get()
- calls clk_prepare_enable() and registers what is needed in order to
call clk_disable_unprepare() when needed, as a managed resource.
This simplifies the code.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240826080408.2522978-1-ruanjinjie@huawei.com
There are no longer any users of the platform data for davinci rawnand
in board files. We can remove the public pdata headers and move the
structures that are still used into the driver compilation unit while
removing the rest.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240814122120.13975-1-brgl@bgdev.pl
Reporting an unclean read from SPI-NAND only when the maximum number
of correctable bitflip errors has been hit seems a bit late.
UBI LEB scrubbing, which depends on the lower MTD device reporting
correctable bitflips, then only kicks in when it's almost too late.
Set bitflip_threshold to 75% of the ECC strength, which is also the
default for raw NAND.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/2117e387260b0a96f95b8e1652ff79e0e2d71d53.1723427450.git.daniel@makrotopia.org
When we are allocating an array, using kmemdup_array() to take care about
multiplication and possible overflows.
Also it makes auditing the code easier.
Signed-off-by: Yan Zhen <yanzhen@vivo.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240823110824.3895787-1-yanzhen@vivo.com
Use of_property_read_bool() to read boolean properties rather than
of_get_property(). This is part of a larger effort to remove callers
of of_get_property() and similar functions. of_get_property() leaks
the DT property data pointer which is a problem for dynamically
allocated nodes which may be freed.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240731191312.1710417-22-robh@kernel.org
- Many fixes for power-cut issues by Zhihao Cheng
- Another ubiblock error path fix
- ubiblock section mismatch fix
- Misc fixes all over the place
-----BEGIN PGP SIGNATURE-----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=0y6/
-----END PGP SIGNATURE-----
Merge tag 'ubifs-for-linus-6.11-rc1-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs
Pull UBI and UBIFS updates from Richard Weinberger:
- Many fixes for power-cut issues by Zhihao Cheng
- Another ubiblock error path fix
- ubiblock section mismatch fix
- Misc fixes all over the place
* tag 'ubifs-for-linus-6.11-rc1-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs:
ubi: Fix ubi_init() ubiblock_exit() section mismatch
ubifs: add check for crypto_shash_tfm_digest
ubifs: Fix inconsistent inode size when powercut happens during appendant writing
ubi: block: fix null-pointer-dereference in ubiblock_create()
ubifs: fix kernel-doc warnings
ubifs: correct UBIFS_DFS_DIR_LEN macro definition and improve code clarity
mtd: ubi: Restore missing cleanup on ubi_init() failure path
ubifs: dbg_orphan_check: Fix missed key type checking
ubifs: Fix unattached inode when powercut happens in creating
ubifs: Fix space leak when powercut happens in linking tmpfile
ubifs: Move ui->data initialization after initializing security
ubifs: Fix adding orphan entry twice for the same inode
ubifs: Remove insert_dead_orphan from replaying orphan process
Revert "ubifs: ubifs_symlink: Fix memleak of inode->i_link in error path"
ubifs: Don't add xattr inode into orphan area
ubifs: Fix unattached xattr inode if powercut happens after deleting
mtd: ubi: avoid expensive do_div() on 32-bit machines
mtd: ubi: make ubi_class constant
ubi: eba: properly rollback inside self_check_eba
Since ubiblock_exit() is now called from an init function,
the __exit section no longer makes sense.
Cc: Ben Hutchings <bwh@kernel.org>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202407131403.wZJpd8n2-lkp@intel.com/
Signed-off-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Zhihao Cheng <chengzhihao1@huawei.com>
When the kmsg_dumper callback parameter changed, the reason variable
in mtdoops_do_dump() was not updated accordingly.
This breaks the build with mtdoops.
Fixes: e1a261ba59 ("printk: Add a short description string to kmsg_dump()")
Suggested-by: Knop Ryszard <ryszard.knop@intel.com>
Signed-off-by: Jocelyn Falempe <jfalempe@redhat.com>
Acked-by: Richard Weinberger <richard@nod.at>
Link: https://patchwork.freedesktop.org/patch/msgid/20240719152542.1554440-1-jfalempe@redhat.com
- Nothing stands out for this merge window, mostly minor fixes, such as
module descriptions, the use of debug macros and Makefile improvements.
Raw NAND changes;
- The Freescale MXC driver has been converted to the newer ->exec_op()
interface. The meson driver now supports handling the boot ROM area
with very specific ECC needs. Support for the iMX8QXP has been added
to the GPMI driver. The lpx32xx driver now can get the DMA channels
using DT entries. The Qcom binding has been improved to be more future
proof by Rob. And then there is the usual load of misc and minor
changes.
SPI-NAND changes:
- The Macronix vendor driver has been improved to support an extended ID
to avoid conflicting with older devices after an ID reuse issue.
SPI NOR changes:
- Drop support for Xilinx S3AN flashes. These flashes are for the very
old Xilinx Spartan 3 FPGAs and they need some awkward code in the core
to support. Drop support for these flashes, along with the special
handling we needed for them in the core like non-power-of-2 page size
handling and the .setup() callback.
- Fix regression for old w25q128 flashes without SFDP tables. Commit
83e824a4a5 ("mtd: spi-nor: Correct flags for Winbond w25q128")
dropped support for such devices under the assumption that they aren't
being used anymore. Users have now surfaced [0] so fix the regression
by supporting both kind of devices.
- Core cleanups including removal of SPI_NOR_NO_FR flag and
simplification of spi_nor_get_flash_info().
[0] https://lore.kernel.org/r/CALxbwRo_-9CaJmt7r7ELgu+vOcgk=xZcGHobnKf=oT2=u4d4aA@mail.gmail.com/
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmabrcwACgkQJWrqGEe9
VoQr4wf/QTC3J4dbLhsaKr5btZt2A+RZ9YibONVvADzP4X+l6+eD7bWubGOlpsjE
n7ne3l8XZuONkLKk6vOxzGEVk+mIAbzwLaB02vRZwHFMyIYcrdyxCihn3heR/AYV
lx+/XG9xfoQueFc5XHcc8BJO/q9UB6eiEwyqp/HAnt1SDXOprr7H4HtjLuAMICmO
4aINAYwZ9bpKwoDix6oDGd/CGiacOIW0Hu4Av5TlBnrggq6EDQfqxym9F2lknJ1g
9VTztYjbgu/NF8bALWr+9OabMxuZmQB2v+xEnTSxnegOeU2uhLo4YR3sK9JR3PCL
BtP6Ny9CJBEt64KQwXAeewDNbzKXJg==
=CJNr
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"Nothing stands out for this merge window, mostly minor fixes, such as
module descriptions, the use of debug macros and Makefile
improvements.
Raw NAND changes;
- The Freescale MXC driver has been converted to the newer
'->exec_op()' interface
- The meson driver now supports handling the boot ROM area with very
specific ECC needs
- Support for the iMX8QXP has been added to the GPMI driver
- The lpx32xx driver now can get the DMA channels using DT entries
- The Qcom binding has been improved to be more future proof by Rob
- And then there is the usual load of misc and minor changes
SPI-NAND changes:
- The Macronix vendor driver has been improved to support an extended
ID to avoid conflicting with older devices after an ID reuse issue
SPI NOR changes:
- Drop support for Xilinx S3AN flashes. These flashes are for the
very old Xilinx Spartan 3 FPGAs and they need some awkward code in
the core to support.
Drop support for these flashes, along with the special handling we
needed for them in the core like non-power-of-2 page size handling
and the .setup() callback.
- Fix regression for old w25q128 flashes without SFDP tables.
Commit 83e824a4a5 ("mtd: spi-nor: Correct flags for Winbond
w25q128") dropped support for such devices under the assumption
that they aren't being used anymore. Users have now surfaced [0] so
fix the regression by supporting both kind of devices.
- Core cleanups including removal of SPI_NOR_NO_FR flag and
simplification of spi_nor_get_flash_info()"
Link: https://lore.kernel.org/r/CALxbwRo_-9CaJmt7r7ELgu+vOcgk=xZcGHobnKf=oT2=u4d4aA@mail.gmail.com/ [0]
* tag 'mtd/for-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (28 commits)
mtd: rawnand: lpx32xx: Fix dma_request_chan() error checks
mtd: spinand: macronix: Add support for serial NAND flash
mtd: spinand: macronix: Add support for reading Device ID 2
mtd: rawnand: lpx32xx: Request DMA channels using DT entries
dt-bindings: mtd: qcom,nandc: Define properties at top-level
mtd: rawnand: intel: use 'time_left' variable with wait_for_completion_timeout()
mtd: rawnand: mxc: use 'time_left' variable with wait_for_completion_timeout()
mtd: rawnand: gpmi: add iMX8QXP support.
mtd: rawnand: gpmi: add 'support_edo_timing' in gpmi_devdata
mtd: cmdlinepart: Replace `dbg()` macro with `pr_debug()`
mtd: add missing MODULE_DESCRIPTION() macros
mtd: make mtd_test.c a separate module
dt-bindings: mtd: gpmi-nand: Add 'fsl,imx8qxp-gpmi-nand' compatible string
mtd: rawnand: cadence: remove unused struct 'ecc_info'
mtd: rawnand: mxc: support software ECC
mtd: rawnand: mxc: implement exec_op
mtd: rawnand: mxc: separate page read from ecc calc
mtd: spi-nor: winbond: fix w25q128 regression
mtd: spi-nor: simplify spi_nor_get_flash_info()
mtd: spi-nor: get rid of SPI_NOR_NO_FR
...
The Freescale MXC driver has been converted to the newer ->exec_op()
interface. The meson driver now supports handling the boot ROM area with
very specific ECC needs. Support for the iMX8QXP has been added to the
GPMI driver. The lpx32xx driver now can get the DMA channels using DT
entries. The Qcom binding has been improved to be more future proof by
Rob. And then there is the usual load of misc and minor changes.
SPI-NAND changes:
The Macronix vendor driver has been improved to support an extended ID
to avoid conflicting with older devices after an ID reuse issue.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmaXhAIACgkQJWrqGEe9
VoR9vAf+LWt1BIHrvvdIkcjGwZ18ZebPZn5q/cEWjCly3uHsqQUz5BpJUlMJ0ekK
3DDIw6QCzWDAw4ZmlDdoNMEesWXKSkYKZeV8LwmWqS2203bZL83FjB5vsVkzUKiV
jl00dh57kl2JEehGzluNEMYZrolPPO4CJd8beE8eVED04JFo4jJdjCL1epYWe8Z7
tsiwfevU11cN7wMSwTgf9L5nsx+CEMtT9hP9WNFNw1zVtLeffzJ9RqhNIvdnYCm8
IFuuyRdOz1YC0dMf74r7HTnuWeJkKQL5ibixLsMRz9UR/LgGdQvxkrqWIijjL2NF
6fkIgzkp7Z7bSEgmpy6IwYucaOHvfA==
=Fu3X
-----END PGP SIGNATURE-----
Merge tag 'nand/for-6.11' into mtd/next
Raw NAND changes;
The Freescale MXC driver has been converted to the newer ->exec_op()
interface. The meson driver now supports handling the boot ROM area with
very specific ECC needs. Support for the iMX8QXP has been added to the
GPMI driver. The lpx32xx driver now can get the DMA channels using DT
entries. The Qcom binding has been improved to be more future proof by
Rob. And then there is the usual load of misc and minor changes.
SPI-NAND changes:
The Macronix vendor driver has been improved to support an extended ID
to avoid conflicting with older devices after an ID reuse issue.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Notable changes:
- Drop support for Xilinx S3AN flashes. These flashes are for the very
old Xilinx Spartan 3 FPGAs and they need some awkward code in the core
to support. Drop support for these flashes, along with the special
handling we needed for them in the core like non-power-of-2 page size
handling and the .setup() callback.
- Fix regression for old w25q128 flashes without SFDP tables. Commit
83e824a4a5 ("mtd: spi-nor: Correct flags for Winbond w25q128")
dropped support for such devices under the assumption that they aren't
being used anymore. Users have now surfaced [0] so fix the regression
by supporting both kind of devices.
- Core cleanups including removal of SPI_NOR_NO_FR flag and
simplification of spi_nor_get_flash_info().
[0] https://lore.kernel.org/r/CALxbwRo_-9CaJmt7r7ELgu+vOcgk=xZcGHobnKf=oT2=u4d4aA@mail.gmail.com/
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQQTlUWNzXGEo3bFmyIR4drqP028CQUCZof+ARQccHJhdHl1c2hA
a2VybmVsLm9yZwAKCRAR4drqP028CXUMAP0X017MY1aWJfUzxNHhhMm23tUtSV5i
Xl1+Hj42oG1AewEAtJ8vOSYwhtPJQ53LQvXqj80HHa5cPx5H5X/vT6okcwU=
=i+Uo
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-6.11' into mtd/next
SPI NOR changes for 6.11
Notable changes:
- Drop support for Xilinx S3AN flashes. These flashes are for the very
old Xilinx Spartan 3 FPGAs and they need some awkward code in the core
to support. Drop support for these flashes, along with the special
handling we needed for them in the core like non-power-of-2 page size
handling and the .setup() callback.
- Fix regression for old w25q128 flashes without SFDP tables. Commit
83e824a4a5 ("mtd: spi-nor: Correct flags for Winbond w25q128")
dropped support for such devices under the assumption that they aren't
being used anymore. Users have now surfaced [0] so fix the regression
by supporting both kind of devices.
- Core cleanups including removal of SPI_NOR_NO_FR flag and
simplification of spi_nor_get_flash_info().
[0] https://lore.kernel.org/r/CALxbwRo_-9CaJmt7r7ELgu+vOcgk=xZcGHobnKf=oT2=u4d4aA@mail.gmail.com/
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
kmsg_dump doesn't forward the panic reason string to the kmsg_dumper
callback.
This patch adds a new struct kmsg_dump_detail, that will hold the
reason and description, and pass it to the dump() callback.
To avoid updating all kmsg_dump() call, it adds a kmsg_dump_desc()
function and a macro for backward compatibility.
I've written this for drm_panic, but it can be useful for other
kmsg_dumper.
It allows to see the panic reason, like "sysrq triggered crash"
or "VFS: Unable to mount root fs on xxxx" on the drm panic screen.
v2:
* Use a struct kmsg_dump_detail to hold the reason and description
pointer, for more flexibility if we want to add other parameters.
(Kees Cook)
* Fix powerpc/nvram_64 build, as I didn't update the forward
declaration of oops_to_nvram()
Signed-off-by: Jocelyn Falempe <jfalempe@redhat.com>
Acked-by: Petr Mladek <pmladek@suse.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Acked-by: Kees Cook <kees@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240702122639.248110-1-jfalempe@redhat.com
The dma_request_chan() returns error pointer in case of error, while
dma_request_channel() returns NULL in case of error therefore different
error checks are needed for the two.
Fixes: 7326d3fb1ee3 ("mtd: rawnand: lpx32xx: Request DMA channels using DT entries")
Signed-off-by: Piotr Wojtaszczyk <piotr.wojtaszczyk@timesys.com>
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240705115139.126522-1-piotr.wojtaszczyk@timesys.com
MX35{U,L}F{2,4}G24AD-Z4I8 are Macronix serial NAND flashes.
Their main difference from MX35{U,L}F{2,4}G24AD lies in
the plane number. The plane number for those with the
postfix Z4I8 is 1.
These flashes have been validated on Xilinx zynq-picozed
board which include Macronix SPI Host.
Signed-off-by: Cheng Ming Lin <chengminglin@mxic.com.tw>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240704024839.241101-3-linchengming884@gmail.com
Adding the Device ID 2 on Macronix serial NAND flash.
When the number of flashes increases, we need to utilize
Device ID 2 to distinguish between different flashes.
These flashes have been validated on Xilinx zynq-picozed
board which included Macronix SPI Host.
Signed-off-by: Cheng Ming Lin <chengminglin@mxic.com.tw>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240704024839.241101-2-linchengming884@gmail.com
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_for_completion_timeout() causing patterns like:
timeout = wait_for_completion_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Fix to the proper variable type 'unsigned long' while here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240604212919.5038-6-wsa+renesas@sang-engineering.com
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_for_completion_timeout() causing patterns like:
timeout = wait_for_completion_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240604212919.5038-5-wsa+renesas@sang-engineering.com
Add "fsl,imx8qxp-gpmi-nand" compatible string. iMX8QXP gpmi nand is similar
to iMX7D. But it is using 4 clocks: "gpmi_io", "gpmi_apb", "gpmi_bch" and
"gpmi_bch_apb".
Signed-off-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240520-gpmi_nand-v2-4-e3017e4c9da5@nxp.com
Introduce a boolean flag, 'support_edo_timing', within gpmi_devdata to
simplify the logic check in gpmi_setup_interface(). This is made in
preparation for adding support for imx8qxp gpmi.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240520-gpmi_nand-v2-3-e3017e4c9da5@nxp.com
The updates to the mediatek, allwinner, ti, tegra, microchip, stm32,
samsung, imx, zynq and amlogic platoforms are farily small maintenance
changes, either addressing minor mistakes or enabling additional hardware.
The qualcomm platform changes add a number of features and are larger
than the other ones combined, introducing the use of linux/cleanup.h
across several drivers, adding support for Snapdragon X1E and other
SoCs in platform drivers, a new "protection domain mapper" driver, and a
"shared memory bridge" driver.
The cznic "turris omnia" router based on Marvell Armada gets a platform
driver that talks to the board specific microcontroller.
The reset and cache subsystems get a few minor updates to SoC specific
drivers, while the ff-a, scmi and optee firmware drivers get some
code refactoring and new features.
-----BEGIN PGP SIGNATURE-----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=ChcR
-----END PGP SIGNATURE-----
Merge tag 'soc-drivers-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC driver updates from Arnd Bergmann:
"The updates to the mediatek, allwinner, ti, tegra, microchip, stm32,
samsung, imx, zynq and amlogic platoforms are fairly small maintenance
changes, either addressing minor mistakes or enabling additional
hardware.
The qualcomm platform changes add a number of features and are larger
than the other ones combined, introducing the use of linux/cleanup.h
across several drivers, adding support for Snapdragon X1E and other
SoCs in platform drivers, a new "protection domain mapper" driver, and
a "shared memory bridge" driver.
The cznic "turris omnia" router based on Marvell Armada gets a
platform driver that talks to the board specific microcontroller.
The reset and cache subsystems get a few minor updates to SoC specific
drivers, while the ff-a, scmi and optee firmware drivers get some code
refactoring and new features"
* tag 'soc-drivers-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (122 commits)
firmware: turris-mox-rwtm: Initialize completion before mailbox
firmware: turris-mox-rwtm: Fix checking return value of wait_for_completion_timeout()
firmware: turris-mox-rwtm: Do not complete if there are no waiters
MAINTAINERS: drop riscv list from cache controllers
platform: cznic: turris-omnia-mcu: fix Kconfig dependencies
bus: sunxi-rsb: Constify struct regmap_bus
soc: sunxi: sram: Constify struct regmap_config
platform: cznic: turris-omnia-mcu: Depend on WATCHDOG
platform: cznic: turris-omnia-mcu: Depend on OF
soc: samsung: exynos-pmu: add support for PMU_ALIVE non atomic registers
arm64: stm32: enable scmi regulator for stm32
firmware: qcom: tzmem: blacklist more platforms for SHM Bridge
soc: qcom: wcnss: simplify with cleanup.h
soc: qcom: pdr: simplify with cleanup.h
soc: qcom: ocmem: simplify with cleanup.h
soc: qcom: mdt_loader: simplify with cleanup.h
soc: qcom: llcc: simplify with cleanup.h
firmware: qcom: tzmem: simplify returning pointer without cleanup
soc: qcom: socinfo: Add PM6350 PMIC
arm64: dts: renesas: rz-smarc: Replace fixed regulator for USB VBUS
...
-----BEGIN PGP SIGNATURE-----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=wVi8
-----END PGP SIGNATURE-----
Merge tag 'for-6.11/block-20240710' of git://git.kernel.dk/linux
Pull block updates from Jens Axboe:
- NVMe updates via Keith:
- Device initialization memory leak fixes (Keith)
- More constants defined (Weiwen)
- Target debugfs support (Hannes)
- PCIe subsystem reset enhancements (Keith)
- Queue-depth multipath policy (Redhat and PureStorage)
- Implement get_unique_id (Christoph)
- Authentication error fixes (Gaosheng)
- MD updates via Song
- sync_action fix and refactoring (Yu Kuai)
- Various small fixes (Christoph Hellwig, Li Nan, and Ofir Gal, Yu
Kuai, Benjamin Marzinski, Christophe JAILLET, Yang Li)
- Fix loop detach/open race (Gulam)
- Fix lower control limit for blk-throttle (Yu)
- Add module descriptions to various drivers (Jeff)
- Add support for atomic writes for block devices, and statx reporting
for same. Includes SCSI and NVMe (John, Prasad, Alan)
- Add IO priority information to block trace points (Dongliang)
- Various zone improvements and tweaks (Damien)
- mq-deadline tag reservation improvements (Bart)
- Ignore direct reclaim swap writes in writeback throttling (Baokun)
- Block integrity improvements and fixes (Anuj)
- Add basic support for rust based block drivers. Has a dummy null_blk
variant for now (Andreas)
- Series converting driver settings to queue limits, and cleanups and
fixes related to that (Christoph)
- Cleanup for poking too deeply into the bvec internals, in preparation
for DMA mapping API changes (Christoph)
- Various minor tweaks and fixes (Jiapeng, John, Kanchan, Mikulas,
Ming, Zhu, Damien, Christophe, Chaitanya)
* tag 'for-6.11/block-20240710' of git://git.kernel.dk/linux: (206 commits)
floppy: add missing MODULE_DESCRIPTION() macro
loop: add missing MODULE_DESCRIPTION() macro
ublk_drv: add missing MODULE_DESCRIPTION() macro
xen/blkback: add missing MODULE_DESCRIPTION() macro
block/rnbd: Constify struct kobj_type
block: take offset into account in blk_bvec_map_sg again
block: fix get_max_segment_size() warning
loop: Don't bother validating blocksize
virtio_blk: Don't bother validating blocksize
null_blk: Don't bother validating blocksize
block: Validate logical block size in blk_validate_limits()
virtio_blk: Fix default logical block size fallback
nvmet-auth: fix nvmet_auth hash error handling
nvme: implement ->get_unique_id
block: pass a phys_addr_t to get_max_segment_size
block: add a bvec_phys helper
blk-lib: check for kill signal in ioctl BLKZEROOUT
block: limit the Write Zeroes to manually writing zeroes fallback
block: refacto blkdev_issue_zeroout
block: move read-only and supported checks into (__)blkdev_issue_zeroout
...
Similar to commit adbf4c4954 ("ubi: block: fix memleak in
ubiblock_create()"), 'dev->gd' is not assigned but dereferenced if
blk_mq_alloc_tag_set() fails, and leading to a null-pointer-dereference.
Fix it by using pr_err() and variable 'dev' to print error log.
Additionally, the log in the error handle path of idr_alloc() has
been improved by using pr_err(), too. Before initializing device
name, using dev_err() will print error log with 'null' instead of
the actual device name, like this:
block (null): ...
~~~~~~
It is unclear. Using pr_err() can print more details of the device.
The improved log is:
ubiblock0_0: ...
Fixes: 77567b25ab ("ubi: use blk_mq_alloc_disk and blk_cleanup_disk")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Li Nan <linan122@huawei.com>
Reviewed-by: Zhihao Cheng <chengzhihao1@huawei.com>
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
The UBIFS_DFS_DIR_LEN macro, which defines the maximum length of the UBIFS
debugfs directory name, has an incorrect formula and misleading comments.
The current formula is (3 + 1 + 2*2 + 1), which assumes that both UBI device
number and volume ID are limited to 2 characters. However, UBI device number
ranges from 0 to 31 (2 characters), and volume ID ranges from 0 to 127 (up
to 3 characters).
Although the current code works due to the cancellation of mathematical
errors (9 + 1 = 10, which matches the correct UBIFS_DFS_DIR_LEN value), it
can lead to confusion and potential issues in the future.
This patch aims to improve the code clarity and maintainability by making
the following changes:
1. Corrects the UBIFS_DFS_DIR_LEN macro definition to (3 + 1 + 2 + 3 + 1),
accommodating the maximum lengths of both UBI device number and volume ID,
plus the separators and null terminator.
2. Updates the snprintf calls to use UBIFS_DFS_DIR_LEN instead of
UBIFS_DFS_DIR_LEN + 1, removing the unnecessary +1.
3. Modifies the error checks to compare against UBIFS_DFS_DIR_LEN using >=
instead of >, aligning with the corrected macro definition.
4. Removes the redundant +1 in the dfs_dir_name array definitions in ubi.h
and debug.h.
While these changes do not affect the runtime behavior, they make the code
more readable, maintainable, and less prone to future errors.
v2->v3:
- Removes the duplicated UBIFS_DFS_DIR_LEN and UBIFS_DFS_DIR_NAME macro
definitions in ubifs.h, as they are already defined in debug.h.
Signed-off-by: ZhaoLong Wang <wangzhaolong1@huawei.com>
Reviewed-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
We need to clean-up debugfs and ubiblock if we fail after initialising
them.
Signed-off-by: Ben Hutchings <ben.hutchings@mind.be>
Fixes: 927c145208 ("mtd: ubi: attach from device tree")
Signed-off-by: Richard Weinberger <richard@nod.at>
The use of do_div() in ubi_nvmem_reg_read() makes calling it on
32-bit machines rather expensive. Since the 'from' variable is
known to be a 32-bit quantity, it is clearly never needed and
can be optimized into a regular division operation.
Fixes: b8a77b9a5f ("mtd: ubi: fix NVMEM over UBI volumes on 32-bit systems")
Fixes: 3ce485803d ("mtd: ubi: provide NVMEM layer over UBI volumes")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Since commit 43a7206b09 ("driver core: class: make class_register() take
a const *"), the driver core allows for struct class to be in read-only
memory, so move the ubi_class structure to be declared at build time
placing it into read-only memory, instead of having to be dynamically
allocated at boot time.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Reviewed-by: Zhihao Cheng <chengzhihao1@huawei.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
In case of a memory allocation failure in the volumes loop we can only
process the already allocated scan_eba and fm_eba array elements on the
error path - others are still uninitialized.
Found by Linux Verification Center (linuxtesting.org).
Fixes: 00abf30415 ("UBI: Add self_check_eba()")
Cc: stable@vger.kernel.org
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Reviewed-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
This macro was left over from the dawn of Git history.
For some reason it was defined in such a way that
you needed double brackets around it. Replace it with
the now-standard `pr_debug()`.
Signed-off-by: Csókás, Bence <csokas.bence@prolan.hu>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240625093148.3579660-1-csokas.bence@prolan.hu
With ARCH=x86, make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/mtd/parsers/brcm_u-boot.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/mtd/parsers/tplink_safeloader.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/mtd/chips/cfi_util.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/mtd/chips/cfi_cmdset_0020.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/mtd/maps/map_funcs.o
Add the missing invocations of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240610-md-drivers-mtd-v1-1-0f59183e4005@quicinc.com
This file gets linked into nine different modules, which causes a warning:
scripts/Makefile.build:236: drivers/mtd/tests/Makefile: mtd_test.o is added to multiple modules: mtd_nandbiterrs mtd_oobtest mtd_pagetest mtd_readtest mtd_speedtest mtd_stresstest mtd_subpagetest mtd_torturetest
Make it a separate module instead.
Fixes: a995c79228 ("mtd: tests: rename sources in order to link a helper object")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240529095049.1915393-1-arnd@kernel.org
With these changes the driver can be used with software BCH ECC which
is useful for NAND chips that require a stronger ECC than the i.MX
hardware supports.
The controller normally interleaves user data with OOB data when
accessing the NAND chip. With Software BCH ECC we write the data
to the NAND in a way that the raw data on the NAND chip matches the
way the NAND layer sees it. This way commands like NAND_CMD_RNDOUT
work as expected.
This was tested on i.MX27 but should work on the other SoCs supported
by this driver as well.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240522-mtd-nand-mxc-nand-exec-op-v4-3-75b611e0ac44@pengutronix.de
Our read_page hook currently reads out a page and also counts and
returns the number of bitflips. In upcoming exec_op conversion we'll
need to read the page data in exec_op, but the bitflip information
will be needed in mxc_nand_read_page(). To ease exec_op conversion
separate the page read out from the bitflip evaluation.
For the v2/v3 controllers we can leave the bitflip information in the
status register for later evaluation. For the v1 controller this is
not possible, because the status register is overwritten with each
subpage read. We therefore store the bitflip information in the private
data.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240522-mtd-nand-mxc-nand-exec-op-v4-1-75b611e0ac44@pengutronix.de
Commit 83e824a4a5 ("mtd: spi-nor: Correct flags for Winbond w25q128")
removed the flags for non-SFDP devices. It was assumed that it wasn't in
use anymore. This wasn't true. Add the no_sfdp_flags as well as the size
again.
We add the additional flags for dual and quad read because they have
been reported to work properly by Hartmut using both older and newer
versions of this flash, the similar flashes with 64Mbit and 256Mbit
already have these flags and because it will (luckily) trigger our
legacy SFDP parsing, so newer versions with SFDP support will still get
the parameters from the SFDP tables.
Reported-by: Hartmut Birr <e9hack@gmail.com>
Closes: https://lore.kernel.org/r/CALxbwRo_-9CaJmt7r7ELgu+vOcgk=xZcGHobnKf=oT2=u4d4aA@mail.gmail.com/
Fixes: 83e824a4a5 ("mtd: spi-nor: Correct flags for Winbond w25q128")
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Michael Walle <mwalle@kernel.org>
Acked-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: Esben Haabendal <esben@geanix.com>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20240621120929.2670185-1-mwalle@kernel.org
Move the add_random flag into the queue_limits feature field so that it
can be set atomically with the queue frozen.
Note that this also removes code from dm to clear the flag based on
the underlying devices, which can't be reached as dm devices will
always start out without the flag set.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20240617060532.127975-16-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Move the nonrot flag into the queue_limits feature field so that it can
be set atomically with the queue frozen.
Use the chance to switch to defaulting to non-rotational and require
the driver to opt into rotational, which matches the polarity of the
sysfs interface.
For the z2ram, ps3vram, 2x memstick, ubiblock and dcssblk the new
rotational flag is not set as they clearly are not rotational despite
this being a behavior change. There are some other drivers that
unconditionally set the rotational flag to keep the existing behavior
as they arguably can be used on rotational devices even if that is
probably not their main use today (e.g. virtio_blk and drbd).
The flag is automatically inherited in blk_stack_limits matching the
existing behavior in dm and md.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20240617060532.127975-15-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Move the cache control settings into the queue_limits so that the flags
can be set atomically with the device queue frozen.
Add new features and flags field for the driver set flags, and internal
(usually sysfs-controlled) flags in the block layer. Note that we'll
eventually remove enough field from queue_limits to bring it back to the
previous size.
The disable flag is inverted compared to the previous meaning, which
means it now survives a rescan, similar to the max_sectors and
max_discard_sectors user limits.
The FLUSH and FUA flags are now inherited by blk_stack_limits, which
simplified the code in dm a lot, but also causes a slight behavior
change in that dm-switch and dm-unstripe now advertise a write cache
despite setting num_flush_bios to 0. The I/O path will handle this
gracefully, but as far as I can tell the lack of num_flush_bios
and thus flush support is a pre-existing data integrity bug in those
targets that really needs fixing, after which a non-zero num_flush_bios
should be required in dm for targets that map to underlying devices.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20240617060532.127975-14-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Rework spi_nor_get_flash_info() to make it look more straight forward
and esp. don't return early. The latter is a preparation to check for
deprecated flashes.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20240603134055.1859863-1-mwalle@kernel.org
While use of fsl_ifc driver with NAND flash is fine, as the fsl_ifc_nand
driver selects FSL_IFC automatically, we need the CONFIG_FSL_IFC option to
be selectable for platforms using fsl_ifc with NOR flash.
Fixes: ea0c0ad6b6 ("memory: Enable compile testing for most of the drivers")
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Esben Haabendal <esben@geanix.com>
Link: https://lore.kernel.org/r/20240530-fsl-ifc-config-v3-1-1fd2c3d233dd@geanix.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
The Everspin FRAM devices are the only user of the NO_FR flag. Drop the
global flag and instead use a manufacturer fixup for the Everspin
flashes to drop the fast read support.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
[pratyush@kernel.org: s/evervision/everspin/g in code and commit message]
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20240419141249.609534-5-mwalle@kernel.org
With the removal of the Xilinx flashes, there is no more flash driver
using that hook. The original intention was to let the driver configure
special requirements like page size an opcodes. This is already
possible by other means and it is unlikely a flash will overwrite the
(more or less complex) setup function.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Acked-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20240419141249.609534-4-mwalle@kernel.org
The Xilinx flashes were the only users of page sizes that were not power
of 2. Support for them has been dropped, thus we can also get rid of the
special page size handling for it.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Acked-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
[pratyush@kernel.org: fixup minor typos and grammar in commit message]
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20240419141249.609534-3-mwalle@kernel.org
These flashes are kind of an oddball for the very old Xilinx Spartan 3
FPGAs to store their bitstream. More importantly, they reuse the Atmel
JEDEC manufacturer ID and in fact the at45db081d already blocks the use
of the 3S700AN flash chip. It's time to sunset support for these
flashes.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Acked-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Cc: Ricardo Ribalda <ribalda@kernel.org>
Acked-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20240419141249.609534-2-mwalle@kernel.org
Boot ROM on Meson needs some pages to be read/written in a special mode:
384 byte ECC mode (so called "short" by Amlogic) and with scrambling
enabled. Such pages are located on the chip in the following way (for
example):
[ p0 ][ p1 ][ p2 ][ p3 ][ p4 ][ p5 ][ p6 ][ p7 ] ... [ pN ]
^ ^ ^ ^
pX is page number "X". "^" means "special" page used by boot ROM - e.g.
every 2nd page in the range of [0, 7]. Step (2 here) and last page in
range is read from the device tree.
Signed-off-by: Arseniy Krasnov <avkrasnov@salutedevices.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240507230903.3399594-4-avkrasnov@salutedevices.com
.setup_interface first gets called with a "target" value of
NAND_DATA_IFACE_CHECK_ONLY, in which case an error is expected
if the controller driver does not support the timing mode (NVDDR).
Fixes: a9ecc8c814 ("mtd: rawnand: Choose the best timings, NV-DDR included")
Signed-off-by: Val Packett <val@packett.cool>
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240519031409.26464-1-val@packett.cool
Early during NAND identification, mtd_info fields have not yet been
initialized (namely, writesize and oobsize) and thus cannot be used for
sanity checks yet. Of course if there is a misuse of
nand_change_read_column_op() so early we won't be warned, but there is
anyway no actual check to perform at this stage as we do not yet know
the NAND geometry.
So, if the fields are empty, especially mtd->writesize which is *always*
set quite rapidly after identification, let's skip the sanity checks.
nand_change_read_column_op() is subject to be used early for ONFI/JEDEC
identification in the very unlikely case of:
- bitflips appearing in the parameter page,
- the controller driver not supporting simple DATA_IN cycles.
As nand_change_read_column_op() uses nand_fill_column_cycles() the logic
explaind above also applies in this secondary helper.
Fixes: c27842e7e1 ("mtd: rawnand: onfi: Adapt the parameter page read to constraint controllers")
Fixes: daca31765e ("mtd: rawnand: jedec: Adapt the parameter page read to constraint controllers")
Cc: stable@vger.kernel.org
Reported-by: Alexander Dahl <ada@thorsis.com>
Closes: https://lore.kernel.org/linux-mtd/20240306-shaky-bunion-d28b65ea97d7@thorsis.com/
Reported-by: Steven Seeger <steven.seeger@flightsystems.net>
Closes: https://lore.kernel.org/linux-mtd/DM6PR05MB4506554457CF95191A670BDEF7062@DM6PR05MB4506.namprd05.prod.outlook.com/
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/linux-mtd/20240516131320.579822-3-miquel.raynal@bootlin.com
The nand_read_data_op() operation, which only consists in DATA_IN
cycles, is sadly not supported by all controllers despite being very
basic. The core, for some time, supposed all drivers would support
it. An improvement to this situation for supporting more constrained
controller added a check to verify if the operation was supported before
attempting it by running the function with the check_only boolean set
first, and then possibly falling back to another (possibly slightly less
optimized) alternative.
An even newer addition moved that check very early and probe time, in
order to perform the check only once. The content of the operation was
not so important, as long as the controller driver would tell whether
such operation on the NAND bus would be possible or not. In practice, no
buffer was provided (no fake buffer or whatever) as it is anyway not
relevant for the "check_only" condition. Unfortunately, early in the
function, there is an if statement verifying that the input parameters
are right for normal use, making the early check always unsuccessful.
Fixes: 9f820fc065 ("mtd: rawnand: Check the data only read pattern only once")
Cc: stable@vger.kernel.org
Reported-by: Alexander Dahl <ada@thorsis.com>
Closes: https://lore.kernel.org/linux-mtd/20240306-shaky-bunion-d28b65ea97d7@thorsis.com/
Reported-by: Steven Seeger <steven.seeger@flightsystems.net>
Closes: https://lore.kernel.org/linux-mtd/DM6PR05MB4506554457CF95191A670BDEF7062@DM6PR05MB4506.namprd05.prod.outlook.com/
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Alexander Dahl <ada@thorsis.com>
Link: https://lore.kernel.org/linux-mtd/20240516131320.579822-2-miquel.raynal@bootlin.com
Until recently the "upper layer" was MTD. But following incremental
reworks to bring spi-nand support and more recently generic ECC support,
there is now an intermediate "generic NAND" layer that also needs to get
access to some values. When using "converted" ECC engines, like the
software ones, these values are already propagated correctly. But
otherwise when using good old raw NAND controller drivers, we need to
manually set these values ourselves at the end of the "scan" operation,
once these values have been negotiated.
Without this propagation, later (generic) checks like the one warning
users that the ECC strength is not high enough might simply no longer
work.
Fixes: 8c126720fe ("mtd: rawnand: Use the ECC framework nand_ecc_is_strong_enough() helper")
Cc: stable@vger.kernel.org
Reported-by: Sascha Hauer <s.hauer@pengutronix.de>
Closes: https://lore.kernel.org/all/Zhe2JtvvN1M4Ompw@pengutronix.de/
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/linux-mtd/20240507085842.108844-1-miquel.raynal@bootlin.com
*-objs suffix is reserved rather for (user-space) host programs while
usually *-y suffix is used for kernel drivers (although *-objs works
for that purpose for now).
Let's correct the old usages of *-objs in Makefiles.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240508151222.1443491-1-andriy.shevchenko@linux.intel.com
Replacement of bdev->bd_inode with sane(r) set of primitives.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQqUNBr3gm4hGXdBJlZ7Krx/gZQ6wUCZkwjlgAKCRBZ7Krx/gZQ
66OmAP9nhZLASn/iM2+979I6O0GW+vid+uLh48uW3d+LbsmVIgD9GYpR+cuLQ/xj
mJESWfYKOVSpFFSrqlzKg9PQlU/GFgs=
=6LRp
-----END PGP SIGNATURE-----
Merge tag 'pull-bd_inode-1' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull bdev bd_inode updates from Al Viro:
"Replacement of bdev->bd_inode with sane(r) set of primitives by me and
Yu Kuai"
* tag 'pull-bd_inode-1' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
RIP ->bd_inode
dasd_format(): killing the last remaining user of ->bd_inode
nilfs_attach_log_writer(): use ->bd_mapping->host instead of ->bd_inode
block/bdev.c: use the knowledge of inode/bdev coallocation
gfs2: more obvious initializations of mapping->host
fs/buffer.c: massage the remaining users of ->bd_inode to ->bd_mapping
blk_ioctl_{discard,zeroout}(): we only want ->bd_inode->i_mapping here...
grow_dev_folio(): we only want ->bd_inode->i_mapping there
use ->bd_mapping instead of ->bd_inode->i_mapping
block_device: add a pointer to struct address_space (page cache of bdev)
missing helpers: bdev_unhash(), bdev_drop()
block: move two helpers into bdev.c
block2mtd: prevent direct access of bd_inode
dm-vdo: use bdev_nr_bytes(bdev) instead of i_size_read(bdev->bd_inode)
blkdev_write_iter(): saner way to get inode and bdev
bcachefs: remove dead function bdev_sectors()
ext4: remove block_device_ejected()
erofs_buf: store address_space instead of inode
erofs: switch erofs_bread() to passing offset instead of block number
Simon Glass wanted to support binman's output properties in order to
check their validity using the binding checks and proposed changes with
the missing properties as well as a binman compatible.
Krzysztof Kozlowski on his side shared a new yaml for describing
Samsung's OneNAND interface.
The interface with NVMEM has also been slightly improved/fixed,
especially now that OTP are also supported in the NAND subsystem.
Along with these changes, small cleanups have also been contributed
around ID tables, structure sizes, arithmetic checks and comments.
* Raw NAND subsystem
Two small fixes, one in the Hynix vendor code for properly returning an
error which might have been ignored and another in the Davinci driver to
properly synchronize the controller with the gpio domain.
* SPI NOR subsystem
SPI NOR now uses div_u64() instead of div64_u64() in places where the
divisor is 32 bits. Many 32 bit architectures can optimize this variant
better than a full 64 bit divide.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmZFzEwACgkQJWrqGEe9
VoRNZwf/dTvWM2r/tLPkXJ4lDdZUMJO2Z5YebSwcUWTJ8P4yhoGfxDwgEiWaaauF
Z++MdSBEK3C9us19ro+YCFidq7T+m1PcekHLa1Zckcy2NOLFyRT7O5j16CEQKHlj
a/9WfZ37TIaWelZDXnm6nWyTxsDFp5h9IOsG32/SckBFm/TU0+G2MCKz7HvJ6DRg
/K6Yu+3KpxhO0D3PhTm5+Fi7UhBPABKfvBYrLFiYnuMi3d0L6/75wxj8dje7iW+Q
9WusrjKvhf3ffp9715RxjDQdMA1MIa/ok7tIlTQXyBfDM1xZkr6MDNeDJfd2FU7J
2hk/ga7A/zigKJ37ftw/34YZJK6xmw==
=AtHp
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"MTD:
- Simon Glass wanted to support binman's output properties in order
to check their validity using the binding checks and proposed
changes with the missing properties as well as a binman compatible.
- Krzysztof Kozlowski on his side shared a new yaml for describing
Samsung's OneNAND interface.
- The interface with NVMEM has also been slightly improved/fixed,
especially now that OTP are also supported in the NAND subsystem.
- Along with these changes, small cleanups have also been contributed
around ID tables, structure sizes, arithmetic checks and comments.
Raw NAND subsystem:
- Two small fixes, one in the Hynix vendor code for properly
returning an error which might have been ignored and another in the
Davinci driver to properly synchronize the controller with the gpio
domain.
SPI NOR subsystem:
- SPI NOR now uses div_u64() instead of div64_u64() in places where
the divisor is 32 bits. Many 32 bit architectures can optimize this
variant better than a full 64 bit divide"
* tag 'mtd/for-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
mtd: spi-nor: replace unnecessary div64_u64() with div_u64()
mtd: mchp23k256: drop unneeded MODULE_ALIAS
dt-bindings: mtd: fixed-partition: Add binman compatibles
dt-bindings: mtd: fixed-partitions: Add alignment properties
mtd: maps: sa1100-flash: Prefer struct_size over open coded arithmetic
mtd: core: Align comment with an action in mtd_otp_nvmem_add()
mtd: rawnand: hynix: fixed typo
mtd: rawnand: davinci: Add dummy read after sending command
mtd: partitions: redboot: Added conversion of operands to a larger type
dt-bindings: mtd: Add Samsung S5Pv210 OneNAND
mtd: core: Don't fail mtd_otp_nvmem_add() if OTP is unsupported
mtd: core: Report error if first mtd_otp_size() call fails in mtd_otp_nvmem_add()
Two small fixes, one in the Hynix vendor code for properly returning an
error which might have been ignored and another in the Davinci driver to
properly synchronize the controller with the gpio domain.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmZFyQMACgkQJWrqGEe9
VoQZEwf+Kxxz73leM+aY3qqKoDk5mqKg7N/rzdTGfBUmTpCm0LclmupmX26dwnmq
kDQic3PzCpZOms3epQXcnLZ7jvLCpPyLcjg5crhXN1inF/M8XEjvbbKFR2VfShcB
EiYJIJgcRmqxv1wnZKn1iyphKJmlR6OuxB6OpFV2lXgw6SF1Cl8JJtPMvyDQkHrU
4BFJNPpvX8Cyu9hNH7zt1iUqaUwq2YKw9xYCPsXGW4T+UsVWhNRnQHf4+LQire2D
hUW3q5Qa+JjbM4GDsFEJ10TPHBeCFV5co388CIBPDdfLIHrleyTiEFbEtUhdtYlo
wxKjqSufF/uR41DnDFI9LZaFNHN3uw==
=ifdO
-----END PGP SIGNATURE-----
Merge tag 'nand/for-6.10' into mtd/next
Raw NAND:
Two small fixes, one in the Hynix vendor code for properly returning an
error which might have been ignored and another in the Davinci driver to
properly synchronize the controller with the gpio domain.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
divisor is 32 bits. Many 32 bit architectures can optimize this variant
better than a full 64 bit divide.
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQQTlUWNzXGEo3bFmyIR4drqP028CQUCZjJfCBQccHJhdHl1c2hA
a2VybmVsLm9yZwAKCRAR4drqP028CV04AQC+9BYCbJi/gnydH9OWzDPVz7CcmkEv
SeJ7ixBhd61P5wD7BHrhACgb+In/R1p9pHkrG8SRwy6rf5BLoYRhxQP0/A0=
=GXM6
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-6.10' into mtd/next
SPI NOR now uses div_u64() instead of div64_u64() in places where the
divisor is 32 bits. Many 32 bit architectures can optimize this variant
better than a full 64 bit divide.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
All we need is size, and that can be obtained via bdev_nr_bytes()
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Link: https://lore.kernel.org/r/20240411145346.2516848-11-viro@zeniv.linux.org.uk
Signed-off-by: Christian Brauner <brauner@kernel.org>
Both occurrences of div64_u64() just have a u8 or u32 divisor. Use
div_u64() instead. Many 32 bit architectures can optimize this variant
better than a full 64 bit divide.
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/9ba7f4e6-2b8b-44a3-9cac-9ed6e50f1700@moroto.mountain/
Signed-off-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
[pratyush@kernel.org: touched up commit message]
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20240429121113.803703-1-mwalle@kernel.org
later also improvements of OTP support in the NAND subsystem. This lead
to situations that we currently cannot handle, so better prevent this
situation from happening in order to avoid canceling device's probe.
In the raw NAND subsystem, two runtime fixes have been shared, one
fixing two important commands in the Qcom driver since it got reworked
and a NULL pointer dereference happening on STB chips.
Arnd also fixed a UBSAN link failure on diskonchip.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmYr9tkACgkQJWrqGEe9
VoTZQQgAr4OXchtvdyr4hyswEKnjJ+cTlmYEd4CYsfq3ECACqsfgqmbWH/Dx8Gol
Yo2vXsucXz1UNxlua/L0LDaI7Hj1GOtY13Tz7QqIsXbp4QHEcAdBDgedmrMdwc6U
ACSGevaamlcvFeVTDpBhHh+tRKNG7xiNGu05t/ECFbJMYHee1VINq6wHLS+Ukdrh
2IDAkRjng4FkpMOnKmCEHiV3ertwq19wqGRr6Hp0MVWSrC7+lwN6KNxaGbEgICCB
KYT161NVG2anft2nZ5wfZlbXZkMmviY2mNHYyzRIBok6RbKlzAjLN8EFO/C5OIKz
pbTdiI6ZfoJqctNXZHLHhmrs8O62SQ==
=1c4F
-----END PGP SIGNATURE-----
Merge tag 'mtd/fixes-for-6.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD fixes from Miquel Raynal:
"There has been OTP support improvements in the NVMEM subsystem, and
later also improvements of OTP support in the NAND subsystem. This
lead to situations that we currently cannot handle, so better prevent
this situation from happening in order to avoid canceling device's
probe.
In the raw NAND subsystem, two runtime fixes have been shared, one
fixing two important commands in the Qcom driver since it got reworked
and a NULL pointer dereference happening on STB chips.
Arnd also fixed a UBSAN link failure on diskonchip"
* tag 'mtd/fixes-for-6.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
mtd: limit OTP NVMEM cell parse to non-NAND devices
mtd: diskonchip: work around ubsan link failure
mtd: rawnand: qcom: Fix broken OP_RESET_DEVICE command in qcom_misc_cmd_type_exec()
mtd: rawnand: brcmnand: Fix data access violation for STB chip
The ID table already has respective entry and MODULE_DEVICE_TABLE and
creates proper alias for SPI driver. Having another MODULE_ALIAS causes
the alias to be duplicated.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240414154943.127079-1-krzk@kernel.org
MTD OTP logic is very fragile on parsing NVMEM cell and can be
problematic with some specific kind of devices.
The problem was discovered by e87161321a ("mtd: rawnand: macronix:
OTP access for MX30LFxG18AC") where OTP support was added to a NAND
device. With the case of NAND devices, it does require a node where ECC
info are declared and all the fixed partitions, and this cause the OTP
codepath to parse this node as OTP NVMEM cells, making probe fail and
the NAND device registration fail.
MTD OTP parsing should have been limited to always using compatible to
prevent this error by using node with compatible "otp-user" or
"otp-factory".
NVMEM across the years had various iteration on how cells could be
declared in DT, in some old implementation, no_of_node should have been
enabled but now add_legacy_fixed_of_cells should be used to disable
NVMEM to parse child node as NVMEM cell.
To fix this and limit any regression with other MTD that makes use of
declaring OTP as direct child of the dev node, disable
add_legacy_fixed_of_cells if we detect the MTD type is Nand.
With the following logic, the OTP NVMEM entry is correctly created with
no cells and the MTD Nand is correctly probed and partitions are
correctly exposed.
Fixes: 4b361cfa86 ("mtd: core: add OTP nvmem provider support")
Cc: <stable@vger.kernel.org> # v6.7+
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240412105030.1598-1-ansuelsmth@gmail.com
I ran into a randconfig build failure with UBSAN using gcc-13.2:
arm-linux-gnueabi-ld: error: unplaced orphan section `.bss..Lubsan_data31' from `drivers/mtd/nand/raw/diskonchip.o'
I'm not entirely sure what is going on here, but I suspect this has something
to do with the check for the end of the doc_locations[] array that contains
an (unsigned long)0xffffffff element, which is compared against the signed
(int)0xffffffff. If this is the case, we should get a runtime check for
undefined behavior, but we instead get an unexpected build-time error.
I would have expected this to work fine on 32-bit architectures despite the
signed integer overflow, though on 64-bit architectures this likely won't
ever work.
Changing the contition to instead check for the size of the array makes the
code safe everywhere and avoids the ubsan check that leads to the link
error. The loop code goes back to before 2.6.12.
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240405143015.717429-1-arnd@kernel.org
While migrating to exec_ops in commit a82990c8a4 ("mtd: rawnand: qcom:
Add read/read_start ops in exec_op path"), OP_RESET_DEVICE command handling
got broken unintentionally. Right now for the OP_RESET_DEVICE command,
qcom_misc_cmd_type_exec() will simply return 0 without handling it. Even,
if that gets fixed, an unnecessary FLASH_STATUS read descriptor command is
being added in the middle and that seems to be causing the command to fail
on IPQ806x devices.
So let's fix the above two issues to make OP_RESET_DEVICE command working
again.
Fixes: a82990c8a4 ("mtd: rawnand: qcom: Add read/read_start ops in exec_op path")
Cc: stable@vger.kernel.org
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240404083157.940-1-ansuelsmth@gmail.com
The comment is related to the non-error case, make it more clear
by inverting the condition. It also makes code neater at the end.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240325151150.3368658-1-andriy.shevchenko@linux.intel.com
Currently a device is only really released once the umount returns to
userspace due to how file closing works. That ultimately could cause
an old umount assumption to be violated that concurrent umount and mount
don't fail. So an exclusively held device with a temporary holder should
be yielded before the filesystem is gone. Add a helper that allows
callers to do that. This also allows us to remove the two holder ops
that Linus wasn't excited about.
Link: https://lore.kernel.org/r/20240326-vfs-bdev-end_holder-v1-1-20af85202918@kernel.org
Fixes: f3a608827d ("bdev: open block device as files") # mainline only
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
The function hynix_nand_rr_init() should probably return an error code.
Judging by the usage, it seems that the return code is passed up
the call stack.
Right now, it always returns 0 and the function hynix_nand_cleanup()
in hynix_nand_init() has never been called.
Found by RASU JSC and Linux Verification Center (linuxtesting.org)
Fixes: 626994e074 ("mtd: nand: hynix: Add read-retry support for 1x nm MLC NANDs")
Signed-off-by: Maxim Korotkov <korotkov.maxim.s@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240313102721.1991299-1-korotkov.maxim.s@gmail.com
Sometimes, writes fail because the tWB_max is not correctly observed
after sending PAGEPROG. It leads to the R/B pin to be read as in
the "ready" state right after sending the command, thus preventing the
normal tPROG delay to be actually observed. This happens because the
ndelay() that waits for tWB_max starts before the command reaches the
NAND chip.
Add a dummy read when a delay is requested at the end of the executed
instruction to make sure that the sent command is received by the NAND
before starting the short ndelay() (<1us but rounded up to 1us in
practice). This read is done on the control register area because
doing it on the Async Data area would change the NAND's RE pin state.
This is not perfect as the two areas are behind two different
devm_ioremap_resource() and could possibly be located on different
interconnects (I did not find more details). This means either the
additional latency due to the load operation is enough impacting, or it
has the expected behavior of ensuring the write has been received.
This has been tested on two platforms designed off of the
DAVINCI/OMAP-L138. The first uses a Toshiba NAND Flash (TC58NYG2S3EBAI5),
the other a Macronix one (MX30UF4G18AC).
Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240308074609.9056-1-bastien.curutchet@bootlin.com
The value of an arithmetic expression directory * master->erasesize is
subject to overflow due to a failure to cast operands to a larger data
type before perfroming arithmetic
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Denis Arefev <arefev@swemel.ru>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240315093758.20790-1-arefev@swemel.ru
Handle the case where -EOPNOTSUPP is returned from OTP driver.
This addresses an issue that occurs with the Intel SPI flash controller,
which has a limited supported opcode set. Whilst the OTP functionality
is not available due to this restriction, other parts of the MTD
functionality of the device are intact. This change allows the driver
to gracefully handle the restriction by allowing the supported
functionality to remain available instead of failing the probe
altogether.
Signed-off-by: Aapo Vienamo <aapo.vienamo@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240313173425.1325790-3-aapo.vienamo@linux.intel.com
Jump to the error reporting code in mtd_otp_nvmem_add() if the
mtd_otp_size() call fails. Without this fix, the error is not logged.
Signed-off-by: Aapo Vienamo <aapo.vienamo@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Walle <mwalle@kernel.org>
Fixes: 4b361cfa86 ("mtd: core: add OTP nvmem provider support")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240313173425.1325790-2-aapo.vienamo@linux.intel.com
UBI:
- Add Zhihao Cheng as reviewer
- Attach via device tree
- Add NVMEM layer
- Various fastmap related fixes
UBIFS:
- Add Zhihao Cheng as reviewer
- Convert to folios
- Various fixes (memory leaks in error paths, function prototypes)
-----BEGIN PGP SIGNATURE-----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=70g8
-----END PGP SIGNATURE-----
Merge tag 'ubifs-for-linus-6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs
Pull UBI and UBIFS updates from Richard Weinberger:
"UBI:
- Add Zhihao Cheng as reviewer
- Attach via device tree
- Add NVMEM layer
- Various fastmap related fixes
UBIFS:
- Add Zhihao Cheng as reviewer
- Convert to folios
- Various fixes (memory leaks in error paths, function prototypes)"
* tag 'ubifs-for-linus-6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs: (34 commits)
mtd: ubi: fix NVMEM over UBI volumes on 32-bit systems
mtd: ubi: provide NVMEM layer over UBI volumes
mtd: ubi: populate ubi volume fwnode
mtd: ubi: introduce pre-removal notification for UBI volumes
mtd: ubi: attach from device tree
mtd: ubi: block: use notifier to create ubiblock from parameter
dt-bindings: mtd: ubi-volume: allow UBI volumes to provide NVMEM
dt-bindings: mtd: add basic bindings for UBI
ubifs: Queue up space reservation tasks if retrying many times
ubifs: ubifs_symlink: Fix memleak of inode->i_link in error path
ubifs: dbg_check_idx_size: Fix kmemleak if loading znode failed
ubi: Correct the number of PEBs after a volume resize failure
ubi: fix slab-out-of-bounds in ubi_eba_get_ldesc+0xfb/0x130
ubi: correct the calculation of fastmap size
ubifs: Remove unreachable code in dbg_check_ltab_lnum
ubifs: fix function pointer cast warnings
ubifs: fix sort function prototype
ubi: Check for too small LEB size in VTBL code
MAINTAINERS: Add Zhihao Cheng as UBI/UBIFS reviewer
ubifs: Convert populate_page() to take a folio
...
- Fix missing prototype warnings in various places, including switching
to using generic cmpdi2/ucmpdi2 and parport.h and stop selecting
unneeded GENERIC_ISA_DMA.
- Reduce duplicate code by using shared font data, with dependency fixup
in separate commit touching lib/fonts.
- Convert sbus drives to use remove callbacks returning void
- Fix return values of __setup handlers
- Section mismatch fix for grpci pci drivers
- Make the vio bus type constant
- Kconfig cleanups and fixes
- Typo fixes
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQQfqfbgobF48oKMeq81AykqDLayywUCZfQtuhQcYW5kcmVhc0Bn
YWlzbGVyLmNvbQAKCRA1AykqDLayy85XAQChTv3muYGiLSyX2r5leQrxZwWNjdiw
W6uc+pM6nCVryAEA+KtjosgriNo7wZViEWqXyYjs/csdEekLpj4U2qBphAg=
=19B/
-----END PGP SIGNATURE-----
Merge tag 'sparc-for-6.9-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/alarsson/linux-sparc
Pull sparc updates from Andreas Larsson:
- Fix missing prototype warnings in various places, including switching
to using generic cmpdi2/ucmpdi2 and parport.h and stop selecting
unneeded GENERIC_ISA_DMA.
- Reduce duplicate code by using shared font data, with dependency
fixup in separate commit touching lib/fonts.
- Convert sbus drives to use remove callbacks returning void
- Fix return values of __setup handlers
- Section mismatch fix for grpci pci drivers
- Make the vio bus type constant
- Kconfig cleanups and fixes
- Typo fixes
* tag 'sparc-for-6.9-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/alarsson/linux-sparc:
lib/fonts: Allow Sparc console 8x16 font for sparc64 early boot text console
sbus: uctrl: Convert to platform remove callback returning void
sbus: flash: Convert to platform remove callback returning void
sbus: envctrl: Convert to platform remove callback returning void
sbus: display7seg: Convert to platform remove callback returning void
sbus: bbc_i2c: Convert to platform remove callback returning void
sbus: Add prototype for bbc_envctrl_init and bbc_envctrl_cleanup to header
sparc32: Fix section mismatch in leon_pci_grpci
sparc32: Fix parport build with sparc32
sparc32: Do not select GENERIC_ISA_DMA
mtd: maps: sun_uflash: Declare uflash_devinit static
sparc32: Fix build with trapbase
sparc32: Use generic cmpdi2/ucmpdi2 variants
sparc: select FRAME_POINTER instead of redefining it
sparc: vDSO: fix return value of __setup handler
sparc64: NMI watchdog: fix return value of __setup handler
sparc: vio: make vio_bus_type const
sparc: Fix typos
sparc: Use shared font data
sparc: remove obsolete config ARCH_ATU
The Carillo Ranch driver has been removed. Top level mtd bindings have
received a couple of improvements (references, selects). The ssfdc
driver received few minor adjustments. These changes come with the usual
load of misc/small improvements and fixes.
Raw NAND
The main series brought is an update of the Broadcom support to support
all BCMBCA SoCs and their specificity (ECC, write protection,
configuration straps), plus a few misc fixes and changes in the main
driver. Device tree updates are also part of this PR, initially because
of a misunderstanding on my side.
The STM32_FMC2 controller driver is also upgraded to properly support
MP1 and MP25 SoCs.
A new compatible is added for an Atmel flavor.
Among all these feature changes, there is as well a load of continuous
read related fixes, avoiding more corner conditions and clarifying the
logic. Finally a few miscellaneous fixes are made to the core, the
lpx32xx_mlc, fsl_lbc, Meson and Atmel controller driver, as well as
final one in the Hynix vendor driver.
SPI-NAND
The ESMT support has been extended to match 5 bytes ID to avoid
collisions. Winbond support on its side receives support for W25N04KV
chips.
SPI NOR
SPI NOR gets the non uniform erase code cleaned. We stopped using
bitmasks for erase types and flags, and instead introduced dedicated
members. We then passed the SPI NOR erase map to MTD. Users can now
determine the erase regions and make informed decisions on partitions
size.
An optional interrupt property is now described in the bindings.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmX0LpsACgkQJWrqGEe9
VoSOCwf8CLhMAsVs/9SrRPMwLuFUGD0IuYYsPl/+qOFXePQOVxNW8s8+DdVrQngW
Oi+unW8MAizPAwMPL9AiyS12WbDVT2qyO0uwX5/efhxXwoNkk+F74icxDBBe1FOu
tnvRRdqY6Zg94T4c1M9BnV5LtW+ozk+F9K8UsYvqnDOcOuaA64qmXRem63s0Jctu
lnmCWHQ0+A8iL7RQ7OMbQswcYQlbnpt7p3lyvDc3dW8K3TRzUtP4nnabL8eiYhqu
ho5SvbWhls91EYf/ij6+SFteV5KN4p+v1ymK2u/AqvCkIW8dAfiIhvvT8dWswpUV
CyC44BFbj3/1ZeSQG4GCXzcNXwnztQ==
=mSyp
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"MTD:
- The Carillo Ranch driver has been removed
- Top level mtd bindings have received a couple of improvements
(references, selects)
- The ssfdc driver received few minor adjustments
- The usual load of misc/small improvements and fixes
Raw NAND:
- The main series brought is an update of the Broadcom support to
support all BCMBCA SoCs and their specificity (ECC, write
protection, configuration straps), plus a few misc fixes and
changes in the main driver. Device tree updates are also part of
this PR, initially because of a misunderstanding on my side.
- The STM32_FMC2 controller driver is also upgraded to properly
support MP1 and MP25 SoCs.
- A new compatible is added for an Atmel flavor.
- Among all these feature changes, there is as well a load of
continuous read related fixes, avoiding more corner conditions and
clarifying the logic. Finally a few miscellaneous fixes are made to
the core, the lpx32xx_mlc, fsl_lbc, Meson and Atmel controller
driver, as well as final one in the Hynix vendor driver.
SPI-NAND:
- The ESMT support has been extended to match 5 bytes ID to avoid
collisions. Winbond support on its side receives support for
W25N04KV chips.
SPI NOR:
- SPI NOR gets the non uniform erase code cleaned. We stopped using
bitmasks for erase types and flags, and instead introduced
dedicated members. We then passed the SPI NOR erase map to MTD.
Users can now determine the erase regions and make informed
decisions on partitions size.
- An optional interrupt property is now described in the bindings"
* tag 'mtd/for-6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (50 commits)
mtd: rawnand: Ensure continuous reads are well disabled
mtd: rawnand: Constrain even more when continuous reads are enabled
mtd: rawnand: brcmnand: Add support for getting ecc setting from strap
mtd: rawnand: brcmnand: fix sparse warnings
mtd: nand: raw: atmel: Fix comment in timings preparation
mtd: rawnand: Ensure all continuous terms are always in sync
mtd: rawnand: Add a helper for calculating a page index
mtd: rawnand: Fix and simplify again the continuous read derivations
mtd: rawnand: hynix: remove @nand_technology kernel-doc description
dt-bindings: atmel-nand: add microchip,sam9x7-pmecc
mtd: rawnand: brcmnand: Support write protection setting from dts
mtd: rawnand: brcmnand: Add BCMBCA read data bus interface
mtd: rawnand: brcmnand: Rename bcm63138 nand driver
arm64: dts: broadcom: bcmbca: Update router boards
arm64: dts: broadcom: bcmbca: Add NAND controller node
ARM: dts: broadcom: bcmbca: Add NAND controller node
mtd: spi-nor: core: correct type of i
mtd: spi-nor: core: set mtd->eraseregions for non-uniform erase map
mtd: spi-nor: core: get rid of SNOR_OVERLAID_REGION flag
mtd: spi-nor: core: get rid of SNOR_LAST_REGION flag
...
The main series brought is an update of the Broadcom support to support
all BCMBCA SoCs and their specificity (ECC, write protection,
configuration straps), plus a few misc fixes and changes in the main
driver. Device tree updates are also part of this PR, initially because
of a misunderstanding on my side.
The STM32_FMC2 controller driver is also upgraded to properly support
MP1 and MP25 SoCs.
A new compatible is added for an Atmel flavor.
Among all these feature changes, there is as well a load of continuous
read related fixes, avoiding more corner conditions and clarifying the
logic. Finally a few miscellaneous fixes are made to the core, the
lpx32xx_mlc, fsl_lbc, Meson and Atmel controller driver, as well as
final one in the Hynix vendor driver.
SPI-NAND
The ESMT support has been extended to match 5 bytes ID to avoid
collisions. Winbond support on its side receives support for W25N04KV
chips.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmXzgv4ACgkQJWrqGEe9
VoTwUAgAqwzuaAbhMuHABS2IJnn9KZHCo4f2goXhtrtRP2oDSgzsT8Yke2vfJTIx
KBtjWRYdp5n8GRSmDmO1n/oNnKdjkzbOhP0ow8aZqhKYtjQ7O0xxd4gxQu3gCoVz
ypWq3tpMkKH0MyD8d+HulFhldMmyGv5BqXeioLi2azeALCbpgVcGAHaMxUlRB/p3
iM3GtBr9hUbai6HlynnPsiAAmyUc1gvGGHJ8t2ShjaW5LzK7uBqJLhSVizfP8I6g
N6l0C+KKwFmXlprtgMcg/HjW2QWKOyeqrhmgTzcJIHRiPjySnmfOVeHBLu6y+1wl
MC3BC5kHNSmOfuU76/93LUQUwkWvUA==
=TaNQ
-----END PGP SIGNATURE-----
Merge tag 'nand/for-6.9' into mtd/next
Raw NAND
The main series brought is an update of the Broadcom support to support
all BCMBCA SoCs and their specificity (ECC, write protection,
configuration straps), plus a few misc fixes and changes in the main
driver. Device tree updates are also part of this PR, initially because
of a misunderstanding on my side.
The STM32_FMC2 controller driver is also upgraded to properly support
MP1 and MP25 SoCs.
A new compatible is added for an Atmel flavor.
Among all these feature changes, there is as well a load of continuous
read related fixes, avoiding more corner conditions and clarifying the
logic. Finally a few miscellaneous fixes are made to the core, the
lpx32xx_mlc, fsl_lbc, Meson and Atmel controller driver, as well as
final one in the Hynix vendor driver.
SPI-NAND
The ESMT support has been extended to match 5 bytes ID to avoid
collisions. Winbond support on its side receives support for W25N04KV
chips.
The cont_read.ongoing flag should only be enabled at the beginning of a
read operation, and also disabled at its end, so we never end up
triggering nasty side effects outside of this scope. The mtd core being
highly serialized, we should not be bothered by parallel accesses
anyway.
In case we reach the end of a read operation and the boolean was not
properly disabled, it's a bug, but it's totally manageable. So warn, and
then fix the boolean state.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240307115315.1942678-2-miquel.raynal@bootlin.com
As a matter of fact, continuous reads require additional handling at the
operation level in order for them to work properly. The core helpers do
have this additional logic now, but any time a controller implements its
own page helper, this extra logic is "lost". This means we need another
level of per-controller driver checks to ensure they can leverage
continuous reads. This is for now unsupported, so in order to ensure
continuous reads are enabled only when fully using the core page
helpers, we need to add more initial checks.
Also, as performance is not relevant during raw accesses, we also
prevent these from enabling the feature.
This should solve the issue seen with controllers such as the STM32 FMC2
when in sequencer mode. In this case, the continuous read feature would
be enabled but not leveraged, and most importantly not disabled, leading
to further operations to fail.
Reported-by: Christophe Kerello <christophe.kerello@foss.st.com>
Fixes: 003fe4b954 ("mtd: rawnand: Support for sequential cache reads")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Christophe Kerello <christophe.kerello@foss.st.com>
Link: https://lore.kernel.org/linux-mtd/20240307115315.1942678-1-miquel.raynal@bootlin.com
BCMBCA broadband SoC based board design does not specify ecc setting in
dts but rather use the SoC NAND strap info to obtain the ecc strength
and spare area size setting. Add brcm,nand-ecc-use-strap dts propety for
this purpose and update driver to support this option. However these two
options can not be used at the same time.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: David Regan <dregan@broadcom.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240301173308.226004-1-william.zhang@broadcom.com
Looks like a copy'n'paste mistake introduced when initially adding the
dynamic timings feature with commit f9ce2eddf1 ("mtd: nand: atmel: Add
->setup_data_interface() hooks"). The context around this and
especially the code itself suggests 'read' is meant instead of write.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Reviewed-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240226122537.75097-1-ada@thorsis.com
While crossing a LUN boundary, it is probably safer (and clearer) to
keep all members of the continuous read structure aligned, including the
pause page (which is the last page of the lun or the last page of the
continuous read). Once these members properly in sync, we can use the
rawnand_cap_cont_reads() helper everywhere to "prepare" the next
continuous read if there is one.
Fixes: bbcd80f53a ("mtd: rawnand: Prevent crossing LUN boundaries during sequential reads")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240223115545.354541-4-miquel.raynal@bootlin.com
The write protection feature is controlled by the module parameter wp_on
with default set to enabled. But not all the board use this feature
especially in BCMBCA broadband board. And module parameter is not
sufficient as different board can have different option. Add a device
tree property and allow this feature to be configured through the board
dts on per board basis.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Kamal Dasu <kamal.dasu@broadcom.com>
Reviewed-by: David Regan <dregan@broadcom.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240223034758.13753-14-william.zhang@broadcom.com
The BCMBCA broadband SoC integrates the NAND controller differently than
STB, iProc and other SoCs. It has different endianness for NAND cache
data.
Add a SoC read data bus shim for BCMBCA to meet the specific SoC need
and performance improvement using the optimized memcpy function on NAND
cache memory.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: David Regan <dregan@broadcom.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240223034758.13753-12-william.zhang@broadcom.com
In preparing to support multiple BCMBCA SoCs, rename bcm63138 to bcmbca
in the driver code and driver file name.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: David Regan <dregan@broadcom.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240223034758.13753-11-william.zhang@broadcom.com
The i should be signed to find out the end of the loop. Otherwise,
i >= 0 is always true and loop becomes infinite. Make its type to be
int.
Fixes: 6a9eda3441 ("mtd: spi-nor: core: set mtd->eraseregions for non-uniform erase map")
Signed-off-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240304090103.818092-1-usama.anjum@collabora.com
bitmasks for erase types and flags, and instead introduced dedicated
members. We then passed the SPI NOR erase map to MTD. Users can now
determine the erase regions and make informed decisions on partitions
size.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEHUIqys8OyG1eHf7fS1VPR6WNFOkFAmXgjyUACgkQS1VPR6WN
FOk75wf8DtDQsjGX3MBAqmLZcCBtDhso6IDGdvGanCrpk8Oi9bD61cqncdgG/lEz
A7Ir7QXDPp8bvzxextJ2XyY2ekk2vfp81kJQx4Ethp7u8MrT3WLydGc4EghmC1OU
FJ7vckp2u/NJZvn1h/DeRPhBxKVnDq0ez1QRyrNj37pw6OoyyGmOf3zHIKWWmAsz
PAThBvqhVSnsOyJDF7deO4j2B7CDOE7KEUWGOIMhnqSj024mQX8PgLERzUzQnu3T
le7lwIhtYX+Ubs9f3dboNiK3hrw95NiIEyYx6HCIUmSeA5x8mGRj8h4Kt5UmFzN4
m5ypa+RgiIZqJozU6pVYgVm3TSml2w==
=hkZT
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-6.9' into mtd/next
SPI NOR gets the non uniform erase code cleaned. We stopped using
bitmasks for erase types and flags, and instead introduced dedicated
members. We then passed the SPI NOR erase map to MTD. Users can now
determine the erase regions and make informed decisions on partitions
size.
This release sees some exciting changes from David Lechner which
implements some optimisations that have been talked about for a long
time which allows client drivers to pre-prepare SPI messages for
repeated or low latency use. This lets us move work out of latency
sensitive paths and avoid repeating work for frequently performed
operations. As well as being useful in itself this will also be used in
future to allow controllers to directly trigger SPI operations (eg, from
interrupts).
Otherwise this release has mostly been focused on cleanups, plus a
couple of new devices:
- Support for pre-optimising messages.
- A big set of updates from Uwe Kleine-König moving drivers to use APIs
with more modern terminology for controllers.
- Major overhaul of the s3c64xx driver.
- Support for Google GS101 and Samsung Exynos850.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmXvHx0ACgkQJNaLcl1U
h9ATVQf/WafEp7ddJ23bRaHZx/gBCMgv8N6mN7OBnzB2pMIGL56SPf9fGAmCUQKt
mne6fDg6/RpydG/72TFppUjRFLN9CwoJjJfQIXMgOqYuPaMEnrj1wbcXar3MeeX2
8hS1u7wKwhOuuwLmoqqMOTKyGUj2mHsBOTOo0vm4WM1s9IHhY5TG2clYv1A+KZbj
kSHE5m7YnBLwimwu0+hsXnRNHZUGKVksQ/9t7AD7/7L8aPj9jPqu1EjTS1/6IDB0
QDVyW7Z6hX7YoUx48gp+j/UFJ7ZyxTajy+0wvzPHou3KJARgFfNZWT2XvvYcpA0/
yqcpbCUwZ1AETXHcmly7YwNpPV9LBg==
=+Xw/
-----END PGP SIGNATURE-----
Merge tag 'spi-v6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"This release sees some exciting changes from David Lechner which
implements some optimisations that have been talked about for a long
time which allows client drivers to pre-prepare SPI messages for
repeated or low latency use. This lets us move work out of latency
sensitive paths and avoid repeating work for frequently performed
operations. As well as being useful in itself this will also be used
in future to allow controllers to directly trigger SPI operations (eg,
from interrupts).
Otherwise this release has mostly been focused on cleanups, plus a
couple of new devices:
- Support for pre-optimising messages
- A big set of updates from Uwe Kleine-König moving drivers to use
APIs with more modern terminology for controllers
- Major overhaul of the s3c64xx driver
- Support for Google GS101 and Samsung Exynos850"
* tag 'spi-v6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (122 commits)
spi: Introduce SPI_INVALID_CS and is_valid_cs()
spi: Fix types of the last chip select storage variables
spi: Consistently use BIT for cs_index_mask
spi: Exctract spi_dev_check_cs() helper
spi: Exctract spi_set_all_cs_unused() helper
spi: s3c64xx: switch exynos850 to new port config data
spi: s3c64xx: switch gs101 to new port config data
spi: s3c64xx: deprecate fifo_lvl_mask, rx_lvl_offset and port_id
spi: s3c64xx: get rid of the OF alias ID dependency
spi: s3c64xx: introduce s3c64xx_spi_set_port_id()
spi: s3c64xx: let the SPI core determine the bus number
spi: s3c64xx: allow FIFO depth to be determined from the compatible
spi: s3c64xx: retrieve the FIFO depth from the device tree
spi: s3c64xx: determine the fifo depth only once
spi: s3c64xx: allow full FIFO masks
spi: s3c64xx: define a magic value
spi: dt-bindings: introduce FIFO depth properties
spi: axi-spi-engine: use struct_size() macro
spi: axi-spi-engine: use __counted_by() attribute
spi: axi-spi-engine: remove p from struct spi_engine_message_state
...
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRAhzRXHqcMeLMyaSiRxhvAZXjcogUCZem4DwAKCRCRxhvAZXjc
ooTRAQDRI6Qz6wJym5Yblta8BScMGbt/SgrdgkoCvT6y83MtqwD+Nv/AZQzi3A3l
9NdULtniW1reuCYkc8R7dYM8S+yAwAc=
=Y1qX
-----END PGP SIGNATURE-----
Merge tag 'vfs-6.9.super' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs
Pull block handle updates from Christian Brauner:
"Last cycle we changed opening of block devices, and opening a block
device would return a bdev_handle. This allowed us to implement
support for restricting and forbidding writes to mounted block
devices. It was accompanied by converting and adding helpers to
operate on bdev_handles instead of plain block devices.
That was already a good step forward but ultimately it isn't necessary
to have special purpose helpers for opening block devices internally
that return a bdev_handle.
Fundamentally, opening a block device internally should just be
equivalent to opening files. So now all internal opens of block
devices return files just as a userspace open would. Instead of
introducing a separate indirection into bdev_open_by_*() via struct
bdev_handle bdev_file_open_by_*() is made to just return a struct
file. Opening and closing a block device just becomes equivalent to
opening and closing a file.
This all works well because internally we already have a pseudo fs for
block devices and so opening block devices is simple. There's a few
places where we needed to be careful such as during boot when the
kernel is supposed to mount the rootfs directly without init doing it.
Here we need to take care to ensure that we flush out any asynchronous
file close. That's what we already do for opening, unpacking, and
closing the initramfs. So nothing new here.
The equivalence of opening and closing block devices to regular files
is a win in and of itself. But it also has various other advantages.
We can remove struct bdev_handle completely. Various low-level helpers
are now private to the block layer. Other helpers were simply
removable completely.
A follow-up series that is already reviewed build on this and makes it
possible to remove bdev->bd_inode and allows various clean ups of the
buffer head code as well. All places where we stashed a bdev_handle
now just stash a file and use simple accessors to get to the actual
block device which was already the case for bdev_handle"
* tag 'vfs-6.9.super' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs: (35 commits)
block: remove bdev_handle completely
block: don't rely on BLK_OPEN_RESTRICT_WRITES when yielding write access
bdev: remove bdev pointer from struct bdev_handle
bdev: make struct bdev_handle private to the block layer
bdev: make bdev_{release, open_by_dev}() private to block layer
bdev: remove bdev_open_by_path()
reiserfs: port block device access to file
ocfs2: port block device access to file
nfs: port block device access to files
jfs: port block device access to file
f2fs: port block device access to files
ext4: port block device access to file
erofs: port device access to file
btrfs: port device access to file
bcachefs: port block device access to file
target: port block device access to file
s390: port block device access to file
nvme: port block device access to file
block2mtd: port device access to files
bcache: port block device access to files
...
A compiler warning related to sizeof(int) != 8 when calling do_div()
is triggered when building on 32-bit platforms.
Address this by using integer types having a well-defined size.
Fixes: 3ce485803d ("mtd: ubi: provide NVMEM layer over UBI volumes")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Zhihao Cheng <chengzhihao1@huawei.com>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
This fixes the following warning:
sun_uflash.c:50:5: error: no previous prototype for 'uflash_devinit'
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Fixes: 0fcb70851f ("Makefile.extrawarn: turn on missing-prototypes globally")
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Cc: Andreas Larsson <andreas@gaisler.com>
Cc: "David S. Miller" <davem@davemloft.net>
Reviewed-by: Andreas Larsson <andreas@gaisler.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Link: https://lore.kernel.org/r/20240224-sam-fix-sparc32-all-builds-v2-3-1f186603c5c4@ravnborg.org
Some of Infineon SPI NOR flash devices support hybrid sector layout that
overlays 4KB sectors on a 256KB sector and SPI NOR framework recognizes
that by parsing SMPT and construct params->erase_map. The hybrid sector
layout is similar to CFI flash devices that have small sectors on top
and/or bottom address. In case of CFI flash devices, the erase map
information is parsed through CFI table and populated into
mtd->eraseregions so that users can create MTD partitions that aligned
with small sector boundaries. This patch provides the same capability to
SPI NOR flash devices that have non-uniform erase map.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Michael Walle <mwalle@kernel.org>
Link: https://lore.kernel.org/r/35d0962986e493b06c13bdf7ada8130a9966dc02.1708404584.git.Takahiro.Kuwano@infineon.com
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Introduce n_regions in spi_nor_erase_map structure and remove
SNOR_LAST_REGION flag. Loop logics that depend on the flag are also
reworked to use n_regions as loop condition.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Suggested-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Suggested-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Michael Walle <mwalle@kernel.org>
Link: https://lore.kernel.org/r/eded84294bd81e966d6f423e578fc2cfb9a4a5b6.1708404584.git.Takahiro.Kuwano@infineon.com
[ta: update spi_nor_init_erase_cmd_list() and break the for loop sooner.]
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Update log level messages so that more critical messages can be logged
to console and help the troubleshooting with field devices.
Signed-off-by: David Regan <dregan@broadcom.com>
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240223034758.13753-4-william.zhang@broadcom.com
FMC2 IP supports up to 4 chip select. On MP1 SoC, only 2 of them are
available when on MP25 SoC, the 4 chip select are available.
Let's use a platform data structure for parameters that will differ.
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240219140505.85794-4-christophe.kerello@foss.st.com
Use dma_get_slave_caps API to get the max burst size of a DMA channel.
For MP1 SoCs, MDMA is used and the max burst size is 128.
For MP25 SoC, DMA3 is used and the max burst size is 64.
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240219140505.85794-3-christophe.kerello@foss.st.com
clang-16 warns about mismatched function prototypes:
drivers/mtd/nand/raw/lpc32xx_mlc.c:783:29: error: cast from 'irqreturn_t (*)(int, struct lpc32xx_nand_host *)' (aka 'enum irqreturn (*)(int, struct lpc32xx_nand_host *)') to 'irq_handler_t' (aka 'enum irqreturn (*)(int, void *)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
Change the interrupt handler to the normal way of just passing
a void* pointer and converting it inside the function..
Fixes: 70f7cb78ec ("mtd: add LPC32xx MLC NAND driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240213100146.455811-1-arnd@kernel.org
This is an effort to get rid of all multiplications from allocation
functions in order to prevent integer overflows [1].
As the "chip" variable is a pointer to "struct mtk_nfc_nand_chip" and
this structure ends in a flexible array:
struct mtk_nfc_nand_chip {
[...]
u8 sels[] __counted_by(nsels);
};
the preferred way in the kernel is to use the struct_size() helper to
do the arithmetic instead of the argument "size + count * size" in the
devm_kzalloc() function.
This way, the code is more readable and safer.
Link: https://www.kernel.org/doc/html/latest/process/deprecated.html#open-coded-arithmetic-in-allocator-arguments [1]
Link: https://github.com/KSPP/linux/issues/160 [2]
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Erick Archer <erick.archer@gmx.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240211091633.4545-1-erick.archer@gmx.com
Scrambling mode is enabled by value (1 << 19). NFC_CMD_SCRAMBLER_ENABLE
is already (1 << 19), so there is no need to shift it again in CMDRWGEN
macro.
Signed-off-by: Arseniy Krasnov <avkrasnov@salutedevices.com>
Cc: <Stable@vger.kernel.org>
Fixes: 8fae856c53 ("mtd: rawnand: meson: add support for Amlogic NAND flash controller")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240210214551.441610-1-avkrasnov@salutedevices.com
The variable bbtblocks is being assigned a value that is never
read. The assignment is redundant and can be removed.
Cleans up clang scan build warning:
drivers/mtd/nand/raw/nand_bbt.c:579:3: warning: Value stored to
'bbtblocks' is never read [deadcode.DeadStores]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240209174019.3933233-1-colin.i.king@gmail.com
