Apply analogix_dp_finish_probe() in order to move the panel/bridge
parsing from Rockchip side to the Analogix side.
Signed-off-by: Damon Ding <damon.ding@rock-chips.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Tested-by: Heiko Stuebner <heiko@sntech.de> # rk3588
Link: https://patch.msgid.link/20260413132551.1049307-5-damon.ding@rock-chips.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Initialize bridge_connector for both Rockchip and Exynos encoder sides.
Then, make DRM_BRIDGE_ATTACH_NO_CONNECTOR mandatory for Analogix bridge
side, as the private &drm_connector is no longer created.
The previous &drm_connector_funcs and &drm_connector_helper_funcs APIs
are replaced by the corresponding &drm_bridge_funcs APIs:
analogix_dp_atomic_check() -> analogix_dp_bridge_atomic_check()
analogix_dp_detect() -> analogix_dp_bridge_detect()
analogix_dp_get_modes() -> analogix_dp_bridge_get_modes()
analogix_dp_bridge_edid_read()
Additionally, the compatibilities of Analogix DP bridge based on whether
the next bridge is a 'panel'. If it is, OP_MODES and OP_DETECT are
supported; If not (the next bridge is a 'monitor' or a bridge chip),
OP_EDID and OP_DETECT are supported.
The devm_drm_bridge_add() is placed in analogix_dp_bind() instead of
analogix_dp_probe(), because the type of next bridge (the panel, monitor
or bridge chip) can only be determined after the probe process has fully
completed.
Signed-off-by: Damon Ding <damon.ding@rock-chips.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de> # rk3588
Link: https://patch.msgid.link/20260413132551.1049307-3-damon.ding@rock-chips.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
For Rockchip platforms, the YUV color formats are currently unsupported.
This compatibility check was previously implemented in
&analogix_dp_plat_data.get_modes().
Moving color format check to &drm_connector_helper_funcs.atomic_check()
would get rid of &analogix_dp_plat_data.get_modes() and be more
reasonable than before.
Signed-off-by: Damon Ding <damon.ding@rock-chips.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de> # rk3588
Link: https://patch.msgid.link/20260409065301.446670-8-damon.ding@rock-chips.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
The result of cdn_dp_reg_write() is checked everywhere (with the error
being logged by the callers) except one place in cdn_dp_config_video().
Add the missing result check, bailing out early on error...
Found by Linux Verification Center (linuxtesting.org) with the Svace static
analysis tool.
Fixes: 1a0f7ed3ab ("drm/rockchip: cdn-dp: add cdn DP support for rk3399")
Signed-off-by: Sergey Shtylyov <s.shtylyov@auroraos.dev>
Cc: stable@vger.kernel.org
Reviewed-by: Chaoyi Chen <chaoyi.chen@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/adf6b313-f7db-4d8f-9000-8c65446ba041@auroraos.dev
Add missing error check for platform_get_resource() return value to
prevent NULL pointer dereference when memory resource is not available.
Fixes: 718b3bb9c0 ("drm/rockchip: analogix_dp: Expand device data to support multiple edp display")
Cc: stable@vger.kernel.org
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20260209033123.1089370-1-nichen@iscas.ac.cn
Simplify encoder initialization and cleanup by making use of
drmm_encoder_init(), which takes care of registering
drm_encoder_cleanup() with drmm_add_action().
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20260310-drm-rk-fixes-v2-6-645ecfb43f49@collabora.com
Included header "rockchip_drm_vop.h" is not directly used, drop it.
While at it, ensure #include directives are ordered alphabetically.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20260310-drm-rk-fixes-v2-5-645ecfb43f49@collabora.com
Make the code a bit more compact by getting rid of the superfluous
assignments around PTR_ERR().
While at it, also drop dev assignment in dw_dp_probe().
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20260310-drm-rk-fixes-v2-4-645ecfb43f49@collabora.com
Attempting to access driver data in the platform driver ->remove()
callback may lead to a null pointer dereference since there is no
guaranty that the component ->bind() callback invoking
platform_set_drvdata() was executed.
A common scenario is when Rockchip DRM driver didn't manage to run
component_bind_all() because of an (unrelated) error causing early
return from rockchip_drm_bind().
Drop the unnecessary call to platform_get_drvdata() and, instead,
reference the target device structure via platform_device.
Fixes: d68ba7bac9 ("drm/rockchip: Add RK3588 DPTX output support")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20260310-drm-rk-fixes-v2-3-645ecfb43f49@collabora.com
Driver makes use of drmm_encoder_init() to initialize the encoder and
automatically handle the cleanup by registering drm_encoder_cleanup()
with drmm_add_action().
However, the internal structure containing the encoder part gets
allocated with devm_kzalloc(), which happens while component_bind_all()
is being called from Rockchip DRM driver. The component framework
further ensures it is deallocated as part of releasing all the resources
claimed during bind, which is triggered from component_unbind_all().
When the reference to the DRM device gets eventually dropped via
drm_dev_put() in rockchip_drm_unbind(), drmm_encoder_alloc_release()
attempts to access the now released encoder structure, leading to
use-after-free.
Ensure driver's internal structure is still reachable on encoder cleanup
by switching from a device-managed allocation to a drm-managed one.
Fixes: d68ba7bac9 ("drm/rockchip: Add RK3588 DPTX output support")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20260310-drm-rk-fixes-v2-2-645ecfb43f49@collabora.com
Driver makes use of drmm_encoder_init() to initialize the encoder and
automatically handle the cleanup by registering drm_encoder_cleanup()
with drmm_add_action().
However, the internal structure containing the encoder part gets
allocated with devm_kzalloc(), which happens while component_bind_all()
is being called from Rockchip DRM driver. The component framework
further ensures it is deallocated as part of releasing all the resources
claimed during bind, which is triggered from component_unbind_all().
When the reference to the DRM device gets eventually dropped via
drm_dev_put() in rockchip_drm_unbind(), drmm_encoder_alloc_release()
attempts to access the now released encoder structure, leading to
use-after-free.
Ensure driver's internal structure is still reachable on encoder cleanup
by switching from a device-managed allocation to a drm-managed one.
Fixes: 969325a259 ("drm/rockchip: inno-hdmi: Convert to drm bridge")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20260310-drm-rk-fixes-v2-1-645ecfb43f49@collabora.com
Now that we introduced a new drm_output_color_format enum to represent
what DRM_COLOR_FORMAT_* bits were representing, we can switch to the new
enum.
The main difference is that while DRM_COLOR_FORMAT_ was a bitmask,
drm_output_color_format is a proper enum. However, the enum was done is
such a way than DRM_COLOR_FORMAT_X = BIT(DRM_OUTPUT_COLOR_FORMAT_X) so
the transitition is easier.
The only thing we need to consider is if the original code meant to use
that value as a bitmask, in which case we do need to keep the bit shift,
or as a discriminant in which case we don't.
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Link: https://lore.kernel.org/r/20260305-drm-rework-color-formats-v3-12-f3935f6db579@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
The Rockchip VOP2 display controller allows configuring the background
color of each video output port.
Since a previous patch introduced the BACKGROUND_COLOR CRTC property,
which defaults to solid black, make use of it when programming the
hardware.
Note the maximum precision allowed by the display controller is 10bpc,
while the alpha component is not supported, hence ignored.
Tested-by: Diederik de Haas <diederik@cknow-tech.com>
Reviewed-by: Andy Yan <andyshrk@163.com>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://patch.msgid.link/20260303-rk3588-bgcolor-v8-4-fee377037ad1@collabora.com
Signed-off-by: Daniel Stone <daniels@collabora.com>
This converts some of the visually simpler cases that have been split
over multiple lines. I only did the ones that are easy to verify the
resulting diff by having just that final GFP_KERNEL argument on the next
line.
Somebody should probably do a proper coccinelle script for this, but for
me the trivial script actually resulted in an assertion failure in the
middle of the script. I probably had made it a bit _too_ trivial.
So after fighting that far a while I decided to just do some of the
syntactically simpler cases with variations of the previous 'sed'
scripts.
The more syntactically complex multi-line cases would mostly really want
whitespace cleanup anyway.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This was done entirely with mindless brute force, using
git grep -l '\<k[vmz]*alloc_objs*(.*, GFP_KERNEL)' |
xargs sed -i 's/\(alloc_objs*(.*\), GFP_KERNEL)/\1)/'
to convert the new alloc_obj() users that had a simple GFP_KERNEL
argument to just drop that argument.
Note that due to the extreme simplicity of the scripting, any slightly
more complex cases spread over multiple lines would not be triggered:
they definitely exist, but this covers the vast bulk of the cases, and
the resulting diff is also then easier to check automatically.
For the same reason the 'flex' versions will be done as a separate
conversion.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The DisplayPort of the RK3576 is basically the same as that of the
RK3588, but it operates in dual-pixel mode and also support MST.
This patch only enable the SST output now.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20260206010421.443605-5-andyshrk@163.com
In the implementation and integration of the SoC, the DW DisplayPort
hardware block can be configured to work in single, dual, quad pixel
mode on differnt platforms, so make the pixel mode set by plat_data
to support the upcoming rk3576 variant.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20260206010421.443605-3-andyshrk@163.com
Replace deprecated DRM_DEV_ERROR() with drm_err_ratelimited() in the VOP2
register wait timeout paths to align with current DRM logging helpers and
avoid flooding the kernel log when timeouts repeat.
Signed-off-by: Hsieh Hung-En <hungen3108@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20260209161621.6136-1-hungen3108@gmail.com
This is the result of running the Coccinelle script from
scripts/coccinelle/api/kmalloc_objs.cocci. The script is designed to
avoid scalar types (which need careful case-by-case checking), and
instead replace kmalloc-family calls that allocate struct or union
object instances:
Single allocations: kmalloc(sizeof(TYPE), ...)
are replaced with: kmalloc_obj(TYPE, ...)
Array allocations: kmalloc_array(COUNT, sizeof(TYPE), ...)
are replaced with: kmalloc_objs(TYPE, COUNT, ...)
Flex array allocations: kmalloc(struct_size(PTR, FAM, COUNT), ...)
are replaced with: kmalloc_flex(*PTR, FAM, COUNT, ...)
(where TYPE may also be *VAR)
The resulting allocations no longer return "void *", instead returning
"TYPE *".
Signed-off-by: Kees Cook <kees@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCgA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAml2lQweHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG0dcH/2yLU3IKlHSSgEDL
Qq3oBuRK/zoVOdy+CM+TmTdl2d1LnBd8J547xFStB7kVGf5mEkdFZdHLBSHRnKDf
ia1SGec06kyLpRX6x5T6FsfwOhkBmVsp59X0coM57QWxxenybugtzPvDO2TQ8/G4
buixJI0jJVgwRwXNzWB4n2W6FxNGui2A7gEN2mjtvkM2t/aDkiDjEqB8ve0pZJX9
4EWhxOgRFzwWgkd/bY+4wgXVXEt3GtI+3VvNncRqLIO00A/AnZOYmH4S2RQUDszD
IbyDscYYxloZcZMDXc3PN2WgD9DCGKuP3GpJGsOHbl0DN6JkqI9nwGsOFZKGVOeF
vbajwPE=
=iAOa
-----END PGP SIGNATURE-----
BackMerge tag 'v6.19-rc7' into drm-next
Linux 6.19-rc7
This is needed for msm and rust trees.
Signed-off-by: Dave Airlie <airlied@redhat.com>
The different Video Ports support different maximum resolutions.
Reject resolutions that are not supported by a specific VP.
Only the output width is checked because the hardware itself does
not have a hard output height limit.
Filter the mode that can't output by the VP/crtc.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com> # Sige5
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20260117020738.294825-1-andyshrk@163.com
The threaded interrupt handler on RK3588 checks HPD IRQ status before
deciding to continue with interrupt clearing and unmasking. However,
this is not really necessary, since the hard interrupt handler already
performs the very same verification before waking the handler thread.
Get rid of the redundant verification of the HPD interrupt status in the
threaded interrupt handler.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20260115-dw-hdmi-qp-hpd-v1-2-e59c166eaa65@collabora.com
The threaded interrupt handler on RK3576 checks HPD IRQ status before
deciding to continue with interrupt clearing and unmasking.
This is not only redundant, since a similar verification has been
already performed by the hard IRQ handler before masking the interrupt,
but is also error prone, because it might happen that hardware clears
the status register right after the masking operation completes, and
before the threaded handler reads its value.
The consequence is that HPD IRQ gets never unmasked, which breaks
hotplug detection until reloading the driver or rebooting the system.
Drop the unnecessary verification of the HPD interrupt status from the
threaded interrupt handler.
Fixes: 36439120ef ("drm/rockchip: dw_hdmi_qp: Add basic RK3576 HDMI output support")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20260115-dw-hdmi-qp-hpd-v1-1-e59c166eaa65@collabora.com
Having only a single set of callbacks, hdmi_clear_infoframe and
hdmi_write_infoframe, bridge drivers don't have an easy way to signal to
the DRM framework, which InfoFrames are actually supported by the
hardware and by the driver and which are not. Also, it makes it
extremely easy for HDMI bridge drivers to skip implementing the
seemingly required InfoFrames (e.g. HDMI VSI). Last, but not least,
those callbacks take a single 'type' parameter, which makes it
impossible to implement support for multiple VSIs (which will be
required once we start working on HDMI Forum VSI).
Split the callbacks into a per-InfoFrame-kind pairs, letting the bridge
drivers actually signal supported features. The implementation follows
the overall drm_bridge design, where the bridge has a single
drm_bridge_funcs implementation and signals, which functions are to be
called using the drm_bridge->ops flags.
The AVI and HDMI VSI are assumed to be required for a normal HDMI
operation (with the drivers getting a drm_warn_once() stub
implementation if one is missing). The Audio InfoFrame is handled by the
existing DRM_BRIDGE_OP_HDMI_AUDIO, while the SPD and HDR DRM InfoFrames
got new drm_bridge_ops values.
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://patch.msgid.link/20260107-limit-infoframes-2-v4-5-213d0d3bd490@oss.qualcomm.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Rockchip display hardware is only available on Rockchip SoCs. Hence add
a dependency on ARCH_ROCKCHIP, to prevent asking the user about this
driver when configuring a kernel without Rockchip platform support.
Before, this dependency was implicit through a hard dependency on
ROCKCHIP_IOMMU.
Fixes: 0244539f9a ("drm/rockchip: Drop ROCKCHIP_IOMMU depend for DRM_ROCKCHIP")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Chaoyi Chen <chaoyi.chen@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/5db192d31cc51f027f107c01c01a353a0569ebf4.1768310045.git.geert+renesas@glider.be
Currently if a user enqueue a work item using schedule_delayed_work() the
used wq is "system_wq" (per-cpu wq) while queue_delayed_work() use
WORK_CPU_UNBOUND (used when a cpu is not specified). The same applies to
schedule_work() that is using system_wq and queue_work(), that makes use
again of WORK_CPU_UNBOUND.
This lack of consistency cannot be addressed without refactoring the API.
system_wq should be the per-cpu workqueue, yet in this name nothing makes
that clear, so replace system_wq with system_percpu_wq.
The old wq (system_wq) will be kept for a few release cycles.
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Marco Crivellari <marco.crivellari@suse.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20251031104846.119503-3-marco.crivellari@suse.com
Currently if a user enqueue a work item using schedule_delayed_work() the
used wq is "system_wq" (per-cpu wq) while queue_delayed_work() use
WORK_CPU_UNBOUND (used when a cpu is not specified). The same applies to
schedule_work() that is using system_wq and queue_work(), that makes use
again of WORK_CPU_UNBOUND.
This lack of consistency cannot be addressed without refactoring the API.
system_unbound_wq should be the default workqueue so as not to enforce
locality constraints for random work whenever it's not required.
Adding system_dfl_wq to encourage its use when unbound work should be used.
The old system_unbound_wq will be kept for a few release cycles.
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Marco Crivellari <marco.crivellari@suse.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20251031104846.119503-2-marco.crivellari@suse.com
On the RK3506 platform, there is no iommu hardware. And even on
platform that have iommu hardware, it should be possible to use
VOP without enabling iommu. In this case, a contiguous memory
space like CMA should be used.
So this patch removes the dependency on ROCKCHIP_IOMMU
with an 'optional-dependency'.
Signed-off-by: Chaoyi Chen <chaoyi.chen@rock-chips.com>
[added reference to optional-dependies description]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20251106020632.92-9-kernel@airkyi.com
The VOP on rk3506:
- Support 2 lane MIPI DSI interface, 1.5Gbps/lane.
- Support RGB interface.
- Max output resolution is 1280x1280@60fps.
- WIN1 layer support RGB888/ARGB8888/RGB565.
- Support Gamma LUT.
Signed-off-by: Chaoyi Chen <chaoyi.chen@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20251106020632.92-10-kernel@airkyi.com
The dsi controller found on RK3506 supports up to 2 lanes.
Signed-off-by: Hongming Zou <hongming.zou@rock-chips.com>
Signed-off-by: Chaoyi Chen <chaoyi.chen@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20251106020632.92-8-kernel@airkyi.com
Make it a little less convoluted, and just directly check if the
combination of plane + format + modifier is supported.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20251215-vop2-atomic-fixups-v5-8-83463c075a8d@collabora.com
We don't need to do a long open-coded walk here; we can simply check the
modifier value.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20251215-vop2-atomic-fixups-v5-7-83463c075a8d@collabora.com
Make sure we can't break the hardware by requesting an unsupported
configuration.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20251215-vop2-atomic-fixups-v5-6-83463c075a8d@collabora.com
Planes can only source AFBC framebuffers at multiples of 4px wide on
RK3566/RK3568. Instead of clipping on all SoCs when the user asks for an
unaligned source rectangle, reject the configuration in the plane's
atomic check on RK3566/RK3568 only.
Signed-off-by: Daniel Stone <daniels@collabora.com>
[Make RK3566/RK3568 specific, reword message, s/byte/pixel/]
Signed-off-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20251215-vop2-atomic-fixups-v5-5-83463c075a8d@collabora.com
It seems only cluster windows are capable of applying downscaling when
the source region has an odd width. Instead of applying a workaround
inside atomic_update, fail the plane check if this is requested.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20251215-vop2-atomic-fixups-v5-4-83463c075a8d@collabora.com
If we want to find out if a window is Esmart or not, test for not being
a cluster window, rather than AFBDC presence.
No functional effect as only cluster windows support AFBC decode.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20251215-vop2-atomic-fixups-v5-3-83463c075a8d@collabora.com
We already clip the plane to the display bounds in atomic_check, and
ensure that it is sufficiently sized. Instead of trying to catch this
and adjust for it in atomic_update, just assert that atomic_check has
done its job.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20251215-vop2-atomic-fixups-v5-2-83463c075a8d@collabora.com
We should never be able to create a framebuffer with an unsupported
format, so throw a warning if this ever happens.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20251215-vop2-atomic-fixups-v5-1-83463c075a8d@collabora.com
The write of cfgdone bits always done at .atomic_flush.
When userspace makes plane zpos changes of two crtc within one commit,
at the .atomic_begin stage, crtcN will never receive the "layer change
cfg done" event of crtcM because crtcM has not yet written "cfgdone".
So only wait when there is pending cfgdone bits to avoid long timeout.
Fixes: 3e89a8c683 ("drm/rockchip: vop2: Fix the update of LAYER/PORT select registers when there are multi display output on rk3588/rk3568")
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20250718064120.8811-2-andyshrk@163.com
According to the implementation of read_poll_timeout_atomic, if the
delay time is 0, it will only use a simple loop based on timeout_us to
decrement the count. Therefore, the final timeout time will differ
significantly from the set timeout time. So, here we set a specific
delay time to ensure that the calculation of the timeout duration
is accurate.
Fixes: 3e89a8c683 ("drm/rockchip: vop2: Fix the update of LAYER/PORT select registers when there are multi display output on rk3588/rk3568")
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20250718064120.8811-1-andyshrk@163.com
After resume from suspend to RAM, the following splash is generated if
the HDMI driver is probed (independent of a connected cable):
[ 1194.484052] irq 80: nobody cared (try booting with the "irqpoll" option)
[ 1194.484074] CPU: 0 UID: 0 PID: 627 Comm: rtcwake Not tainted 6.17.0-rc7-g96f1a11414b3 #1 PREEMPT
[ 1194.484082] Hardware name: Rockchip RK3576 EVB V10 Board (DT)
[ 1194.484085] Call trace:
[ 1194.484087] ... (stripped)
[ 1194.484283] handlers:
[ 1194.484285] [<00000000bc363dcb>] dw_hdmi_qp_main_hardirq [dw_hdmi_qp]
[ 1194.484302] Disabling IRQ #80
Apparently the HDMI IP is losing part of its state while the system
is suspended and generates spurious interrupts during resume. The
bug has not yet been noticed, as system suspend does not yet work
properly on upstream kernel with either the Rockchip RK3588 or RK3576
platform.
Fixes: 128a9bf8ac ("drm/rockchip: Add basic RK3588 HDMI output support")
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20251014-rockchip-hdmi-suspend-fix-v1-1-983fcbf44839@collabora.com
Convert it to drm bridge driver, it will be convenient for us to
migrate the connector part to the display driver later.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20251016083843.76675-2-andyshrk@163.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
The RK3368 has only one VOP, so there is no source selection happening
and the controller uses an internal PHY for the HDMI output.
Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
Reviewed-by: Andy Yan <andyshrk@163.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20251021074254.87065-3-heiko@sntech.de
UAPI Changes:
- Add support for drm colorop pipeline.
- Add COLOR PIPELINE plane property.
- Add DRM_CLIENT_CAP_PLANE_COLOR_PIPELINE.
Cross-subsystem Changes:
- Attempt to use higher order mappings in system heap allocator.
- Always taint kernel with sw-sync.
Core Changes:
- Small fixes to drm/gem.
- Support emergency restore to drm-client.
- Allocate and release fb_info in single place.
- Rework ttm pipelined eviction fence handling.
Driver Changes:
- Support the drm color pipeline in vkms, amdgfx.
- Add NVJPG driver for tegra.
- Assorted small fixes and updates to rockchip, bridge/dw-hdmi-qp,
panthor.
- Add ASL CS5263 DP-to-HDMI simple bridge.
- Add and improve support for G LD070WX3-SL01 MIPI DSI, Samsung LTL106AL0,
Samsung LTL106AL01, Raystar RFF500F-AWH-DNN, Winstar WF70A8SYJHLNGA,
Wanchanglong w552946aaa, Samsung SOFEF00, Lenovo X13s panel.
- Add support for it66122 to it66121.
- Support mali-G1 gpu in panthor.
-----BEGIN PGP SIGNATURE-----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=QBjM
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2025-12-01-1' of https://gitlab.freedesktop.org/drm/misc/kernel into drm-next
Extra drm-misc-next for v6.19-rc1:
UAPI Changes:
- Add support for drm colorop pipeline.
- Add COLOR PIPELINE plane property.
- Add DRM_CLIENT_CAP_PLANE_COLOR_PIPELINE.
Cross-subsystem Changes:
- Attempt to use higher order mappings in system heap allocator.
- Always taint kernel with sw-sync.
Core Changes:
- Small fixes to drm/gem.
- Support emergency restore to drm-client.
- Allocate and release fb_info in single place.
- Rework ttm pipelined eviction fence handling.
Driver Changes:
- Support the drm color pipeline in vkms, amdgfx.
- Add NVJPG driver for tegra.
- Assorted small fixes and updates to rockchip, bridge/dw-hdmi-qp,
panthor.
- Add ASL CS5263 DP-to-HDMI simple bridge.
- Add and improve support for G LD070WX3-SL01 MIPI DSI, Samsung LTL106AL0,
Samsung LTL106AL01, Raystar RFF500F-AWH-DNN, Winstar WF70A8SYJHLNGA,
Wanchanglong w552946aaa, Samsung SOFEF00, Lenovo X13s panel.
- Add support for it66122 to it66121.
- Support mali-G1 gpu in panthor.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patch.msgid.link/aa5cbd50-7676-4a59-bbed-e8428af86804@linux.intel.com
-----BEGIN PGP SIGNATURE-----
iQFSBAABCgA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmkaT2IeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGnakIAIq6O35+abAlDGe7
n8IwX/4hwDJ9Ol2vddg6jTdio3szSlvcXRAyijkG35etLap+i+Q78Q9H1fRcQ8CF
5t9kfs5oCVWEDlsHMI+Q38vYB3tWikaIUIuao6pH5U50fsA0KM/287TLYdzvmBsK
gy0BHoZhl++xdMsD2HNwt08RrK/IyY+Zp9i7pKhcsxJiJCgy8nq5ZxhmRPbqTKNc
IqIBPzG+UYcOd88Iz377Ax+TnzWaTpwyvfaiU8DVFMN0FeENdk1FY8ClYfpYxCDH
Pm5NzL/f54VtdZ3aL1fKmYwWN7WFJT4FH3l6DOvtCc+Gx3KW1a3Y508CbqYBXvgY
QV4oH4Y=
=iSoY
-----END PGP SIGNATURE-----
Merge tag 'v6.18-rc6' into drm-next
Linux 6.18-rc6
Backmerge in order to merge msm next
Signed-off-by: Dave Airlie <airlied@redhat.com>
When there are multiple Video Ports, and only one of them is working
(for example, VP1 is working while VP0 is not), in this case, the
win_mask of VP0 is 0. However, we have already set the port mux for VP0
according to vp0->nlayers, and at the same time, in the OVL_LAYER_SEL
register, there are windows will also be assigned to layers which will
map to the inactive VPs. In this situation, vp0->win_mask is zero as it
now working, it is more reliable to calculate the used layers based on
the configuration of the OVL_LAYER_SEL register.
Note: as the configuration of OVL_LAYER_SEL is take effect when the
vsync is come, so we use the value backup in vop2->old_layer_sel instead
of read OVL_LAYER_SEL directly.
Fixes: 3e89a8c683 ("drm/rockchip: vop2: Fix the update of LAYER/PORT select registers when there are multi display output on rk3588/rk3568")
Cc: stable@vger.kernel.org
Reported-by: Diederik de Haas <diederik@cknow-tech.com>
Closes: https://bugs.kde.org/show_bug.cgi?id=511274
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Tested-by: Dang Huynh <dang.huynh@mainlining.org>
Tested-by: Diederik de Haas <diederik@cknow-tech.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20251112085024.2480111-1-andyshrk@163.com
Use VOP for DMA operations performed by DRM core. Rockchip DRM driver
is backed by a virtual device that isn't IOMMU-capable, while VOP is the
actual display controller device backed by IOMMU. Fixes "swiotlb buffer
is full" warning messages originated from GEM prime code paths.
Note, that backporting is non-trivial as this depends on
commit 143ec8d3f9 ("drm/prime: Support dedicated DMA device for dma-buf
imports"), which landed in v6.16 and commit 421be3ee36 ("drm/rockchip:
Refactor IOMMU initialisation"), which landed in v5.19.
Reported-by: Daniel Stone <daniels@collabora.com>
Fixes: 2048e3286f ("drm: rockchip: Add basic drm driver")
Cc: stable@vger.kernel.org # v6.16+
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Tested-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20251022161948.199731-1-dmitry.osipenko@collabora.com
Since both RK3576 and RK3588 SoCs are capable of handling 10 bpc color
depth, introduce a pair of new helpers to program the necessary
registers, as well as passing bpc at PHY configuration level.
Note max_bpc is unconditionally set to 10 before initializing the QP
bridge library, as there is no need to adjust it dynamically, i.e. per
SoC variant, for now.
While setting up .enc_init() callbacks of rockchip_hdmi_qp_ctrl_ops,
also replace the unnecessary whitespace chars before .irq_callback()
assignments.
Acked-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20251021-rk3588-10bpc-v3-5-3d3eed00a6db@collabora.com
For consistency and improved readability, redefine a few RK3576 specific
register configurations by relying on GENMASK() and unshifted values for
color depth and output format. Those are not used at the moment, but
will be needed soon to support the related features.
While at it, drop a few other defines which are unlikely to be ever
required.
Acked-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20251021-rk3588-10bpc-v3-4-3d3eed00a6db@collabora.com
Stop relying on phy_set_bus_width() based workaround to setup the TMDS
character rate and, instead, use the recently introduced HDMI PHY
configuration API. This is also a prerequisite to enable high color
depth and FRL support.
Additionally, move the logic to ->atomic_check() callback where the
current mode rate is already provided by the connector state. As a
matter of fact this is actually necessary to ensure the link rate is
configured before VOP2 attempts to use the PHY PLL as a DCLK source in
vop2_crtc_atomic_enable(). The rationale is to restrict any changes of
the PHY rate via CCF and, instead, prefer the PHY configuration API for
this purpose.
Acked-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20251021-rk3588-10bpc-v3-3-3d3eed00a6db@collabora.com
When making use of the HDMI PHY PLL as a VOP2 DCLK source, it's output
rate does normally match the mode clock. But this is only applicable
for default color depth of 8 bpc. For higher depths, the output clock
is further divided by the hardware according to the formula:
output rate = PHY PLL rate * 8 / bpc
Hence there is no need for VOP2 to compensate for bpc when adjusting
DCLK, but it is required to do so when computing its maximum operating
frequency.
Take color depth into consideration before deciding to switch DCLK
source.
Reviewed-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20251021-rk3588-10bpc-v3-1-3d3eed00a6db@collabora.com
The DRM_DEV_ERROR() has been deprecated, and use dev_err_probe()
can be better. The other reason is that dev_err_probe() help avoid
unexpected repeated err logs during defered probing.
Signed-off-by: Damon Ding <damon.ding@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20251110075817.1159857-1-damon.ding@rock-chips.com
The name of the enable_gpio member in struct rockchip_hdmi_qp is too
generic, as initially "borrowed" from downstream BSP code. Moreover,
this hasn't been really in use so far, since there is neither a DT
providing an "enable-gpios" property to any of the "hdmi" nodes, nor a
binding documenting it.
The actual purpose of this GPIO line is to control the voltage bias for
the HDMI TX data lines when switching between TMDS and FRL operating
modes.
A previous patch introduced the "frl-enable-gpios" property of the
RK3588 HDMI TX Controller binding, hence pass the updated string to
devm_gpiod_get_optional(), rename the struct member accordingly and set
it to a low level.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20251027222641.25066-3-laurent.pinchart@ideasonboard.com
There are a gazillion files that depend on drm_print.h being indirectly
included via drm_buddy.h, drm_mm.h, or ttm/ttm_resource.h. In
preparation for removing those includes, explicitly include drm_print.h
where needed.
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://lore.kernel.org/r/5fe67395907be33eb5199ea6d540e29fddee71c8.1761734313.git.jani.nikula@intel.com
The VOP2 has limitations on its input and output sizes. The clipped
display region must be at least 4px in each dimension for both
framebuffer source and plane destination, and the clipped source region
must be no greater than a per-version limit.
It is never valid for VOP2 to have a framebuffer which is less than four
pixels in either dimension, so declare that as our min width/height,
enforced by AddFB failing if the user tries. It can theoretically be
valid to have a single large framebuffer of which only certain clipped
regions are shown, but this is a very uncommon case. Declaring to
userspace that the framebuffer's maximum width and height is the maximum
source clip helps it make better decisions as to which mode to use,
instead of trying unsupported sizes and having to fall back.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20251015110042.41273-3-daniels@collabora.com
A plane check failing is a normal and expected condition, as userspace
isn't aware of the specific constraints and will try any and every
combination until one succeeds. Push this down to a debug message, so
users can see it if they want to, but make sure we don't spam the log
during normal operation.
Fixes: 604be85547 ("drm/rockchip: Add VOP2 driver")
Signed-off-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20251015110042.41273-2-daniels@collabora.com
In dw_hdmi_rk3228_setup_hpd(), the SCLIN mask incorrectly references
the RK3328 variant. This change updates it to the RK3228-specific mask
RK3228_HDMI_SCLIN_MSK using FIELD_PREP_WM16, ensuring proper HPD and
I2C pin configuration for RK3228.
Change: RK3328_HDMI_SCLIN_MSK -> RK3228_HDMI_SCLIN_MSK
Fixes: 63df37f3fc ("drm/rockchip: dw_hdmi: switch to FIELD_PREP_WM16* macros")
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Reviewed-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20251010173143.72733-1-alok.a.tiwari@oracle.com
In order to support correct initialization of the timer base in the HDMI
QP IP block, setup platform data to include the required reference clock
rate.
While at it, ensure plat_data is zero-initialized in
dw_hdmi_qp_rockchip_bind().
Reviewed-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250903-rk3588-hdmi-cec-v4-5-fa25163c4b08@collabora.com
In order to support the CEC interface of the DesignWare HDMI QP IP
block, setup platform data to include the required IRQ number.
Reviewed-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250903-rk3588-hdmi-cec-v4-4-fa25163c4b08@collabora.com
The error handling in dw_hdmi_qp_rockchip_bind() is quite inconsistent,
i.e. in some cases the error code is not included in the message, while
in some other cases there is no check for -EPROBE_DEFER.
Since this is part of the probe path, address the aforementioned issues
by switching to dev_err_probe(), which also reduces the code a bit.
Reviewed-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250903-rk3588-hdmi-cec-v4-3-fa25163c4b08@collabora.com
The "grf" clock is optional for Rockchip eDP controller(RK3399 needs
while RK3288 and RK3588 do not).
It can make the code more concise to use devm_clk_get_optional()
instead of devm_clk_get() with extra checks.
In addtion, DRM_DEV_ERROR() is replaced by dev_err_probe().
Signed-off-by: Damon Ding <damon.ding@rock-chips.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250928103734.4007257-1-damon.ding@rock-chips.com
The vop2_plane_atomic_check() function incorrectly checks
drm_rect_width(dest) twice instead of verifying both width and height.
Fix the second condition to use drm_rect_height(dest) so that invalid
destination rectangles with height < 4 are correctly rejected.
Fixes: 604be85547 ("drm/rockchip: Add VOP2 driver")
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Reviewed-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20251012142005.660727-1-alok.a.tiwari@oracle.com
The rockchip atomic_check implementation uses the deprecated
drm_atomic_get_existing_crtc_state() helper.
This hook is called as part of the global atomic_check, thus before the
states are swapped. The existing state thus points to the new state, and
we can use drm_atomic_get_new_crtc_state() instead.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://lore.kernel.org/r/20250930-drm-no-more-existing-state-v5-27-eeb9e1287907@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
cross-subsystem:
- i2c-hid: Make elan touch controllers power on after panel is enabled
- dt bindings for STM32MP25 SoC
- pci vgaarb: use screen_info helpers
- rust pin-init updates
- add MEI driver for late binding firmware update/load
uapi:
- add ioctl for reassigning GEM handles
- provide boot_display attribute on boot-up devices
core:
- document DRM_MODE_PAGE_FLIP_EVENT
- add vendor specific recovery method to drm device wedged uevent
gem:
- Simplify gpuvm locking
ttm:
- add interface to populate buffers
sched:
- Fix race condition in trace code
atomic:
- Reallow no-op async page flips
display:
- dp: Fix command length
video:
- Improve pixel-format handling for struct screen_info
rust:
- drop Opaque<> from ioctl args
- Alloc:
- BorrowedPage type and AsPageIter traits
- Implement Vmalloc::to_page() and VmallocPageIter
- DMA/Scatterlist:
- Add dma::DataDirection and type alias for dma_addr_t
- Abstraction for struct scatterlist and sg_table
- DRM:
- simplify use of generics
- add DriverFile type alias
- drop Object::SIZE
- Rust:
- pin-init tree merge
- Various methods for AsBytes and FromBytes traits
gpuvm:
- Support madvice in Xe driver
gpusvm:
- fix hmm_pfn_to_map_order usage in gpusvm
bridge:
- Improve and fix ref counting on bridge management
- cdns-dsi: Various improvements to mode setting
- Support Solomon SSD2825 plus DT bindings
- Support Waveshare DSI2DPI plus DT bindings
- Support Content Protection property
- display-connector: Improve DP display detection
- Add support for Radxa Ra620 plus DT bindings
- adv7511: Provide SPD and HDMI infoframes
- it6505: Replace crypto_shash with sha()
- synopsys: Add support for DW DPTX Controller plus DT bindings
- adv7511: Write full Audio infoframe
- ite6263: Support vendor-specific infoframes
- simple: Add support for Realtek RTD2171 DP-to-HDMI plus DT bindings
panel:
- panel-edp: Support mt8189 Chromebooks; Support BOE NV140WUM-N64;
Support SHP LQ134Z1; Fixes
- panel-simple: Support Olimex LCD-OLinuXino-5CTS plus DT bindings
- Support Samsung AMS561RA01
- Support Hydis HV101HD1 plus DT bindings
- ilitek-ili9881c: Refactor mode setting; Add support for Bestar
BSD1218-A101KL68 LCD plus DT bindings
- lvds: Add support for Ampire AMP19201200B5TZQW-T03 to DT bindings
- edp: Add support for additonal mt8189 Chromebook panels
- lvds: Add DT bindings for EDT ETML0700Z8DHA
amdgpu:
- add CRIU support for gem objects
- RAS updates
- VCN SRAM load fixes
- EDID read fixes
- eDP ALPM support
- Documentation updates
- Rework PTE flag generation
- DCE6 fixes
- VCN devcoredump cleanup
- MMHUB client id fixes
- VCN 5.0.1 RAS support
- SMU 13.0.x updates
- Expanded PCIe DPC support
- Expanded VCN reset support
- VPE per queue reset support
- give kernel jobs unique id for tracing
- pre-populate exported buffers
- cyan skillfish updates
- make vbios build number available in sysfs
- userq updates
- HDCP updates
- support MMIO remap page as ttm pool
- JPEG parser updates
- DCE6 DC updates
- use devm for i2c buses
- GPUVM locking updates
- Drop non-DC DCE11 code
- improve fallback handling for pixel encoding
amdkfd:
- SVM/page migration fixes
- debugfs fixes
- add CRIO support for gem objects
- SVM updates
radeon:
- use dev_warn_once in CS parsers
xe:
- add madvise interface
- add DRM_IOCTL_XE_VM_QUERY_MEMORY_RANGE_ATTRS to query VMA count
and memory attributes
- drop L# bank mask reporting from media GT3 on Xe3+.
- add SLPC power_profile sysfs interface
- add configs attribs to add post/mid context-switch commands
- handle firmware reported hardware errors notifying userspace with
device wedged uevent
- use same dir structure across sysfs/debugfs
- cleanup and future proof vram region init
- add G-states and PCI link states to debugfs
- Add SRIOV support for CCS surfaces on Xe2+
- Enable SRIOV PF mode by default on supported platforms
- move flush to common code
- extended core workarounds for Xe2/3
- use DRM scheduler for delayed GT TLB invalidations
- configs improvements and allow VF device enablement
- prep work to expose mmio regions to userspace
- VF migration support added
- prepare GPU SVM for THP migration
- start fixing XE_PAGE_SIZE vs PAGE_SIZE
- add PSMI support for hw validation
- resize VF bars to max possible size according to number of VFs
- Ensure GT is in C0 during resume
- pre-populate exported buffers
- replace xe_hmm with gpusvm
- add more SVM GT stats to debugfs
- improve fake pci and WA kunnit handle for new platform testing
- Test GuC to GuC comms to add debugging
- use attribute groups to simplify sysfs registration
- add Late Binding firmware code to interact with MEI
i915:
- apply multiple JSL/EHL/Gen7/Gen6 workarounds properly
- protect against overflow in active_engine()
- Use try_cmpxchg64() in __active_lookup()
- include GuC registers in error state
- get rid of dev->struct_mutex
- iopoll: generalize read_poll_timout
- lots more display refactoring
- Reject HBR3 in any eDP Panel
- Prune modes for YUV420
- Display Wa fix, additions, and updates
- DP: Fix 2.7 Gbps link training on g4x
- DP: Adjust the idle pattern handling
- DP: Shuffle the link training code a bit
- Don't set/read the DSI C clock divider on GLK
- Enable_psr kernel parameter changes
- Type-C enabled/disconnected dp-alt sink
- Wildcat Lake enabling
- DP HDR updates
- DRAM detection
- wait PSR idle on dsb commit
- Remove FBC modulo 4 restriction for ADL-P+
- panic: refactor framebuffer allocation
habanalabs:
- debug/visibility improvements
- vmalloc-backed coherent mmap support
- HLDIO infrastructure
nova-core:
- various register!() macro improvements
- minor vbios/firmware fixes/refactoring
- advance firmware boot stages; process Booter and patch signatures
- process GSP and GSP bootloader
- Add r570.144 firmware bindings and update to it
- Move GSP boot code to own module
- Use new pin-init features to store driver's private data in a single
allocation
- Update ARef import from sync::aref
nova-drm:
- Update ARef import from sync::aref
tyr:
- initial driver skeleton for a rust driver for ARM Mali GPUs
- capable of powering up, query metadata and provide it to userspace.
msm:
- GPU and Core:
- in DT bindings describe clocks per GPU type
- GMU bandwidth voting for x1-85
- a623/a663 speedbins
- cleanup some remaining no-iommu leftovers after VM_BIND conversion
- fix GEM obj 32b size truncation
- add missing VM_BIND param validation
- IFPC for x1-85 and a750
- register xml and gen_header.py sync from mesa
- Display:
- add missing bindings for display on SC8180X
- added DisplayPort MST bindings
- conversion from round_rate() to determine_rate()
amdxdna:
- add IOCTL_AMDXDNA_GET_ARRAY
- support user space allocated buffers
- streamline PM interfaces
- Refactoring wrt. hardware contexts
- improve error reporting
nouveau:
- use GSP firmware by default
- improve error reporting
- Pre-populate exported buffers
ast:
- Clean up detection of DRAM config
exynos:
- add DSIM bridge driver support for Exynos7870
- Document Exynos7870 DSIM compatible in dt-binding
panthor:
- Print task/pid on errors
- Add support for Mali G710, G510, G310, Gx15, Gx20, Gx25
- Improve cache flushing
- Fail VM bind if BO has offset
renesas:
- convert to RUNTIME_PM_OPS
rcar-du:
- Make number of lanes configurable
- Use RUNTIME_PM_OPS
- Add support for DSI commands
rocket:
- Add driver for Rockchip NPU plus DT bindings
- Use kfree() and sizeof() correctly
- Test DMA status
rockchip:
- dsi2: Add support for RK3576 plus DT bindings
- Add support for RK3588 DPTX output
tidss:
- Use crtc_ fields for programming display mode
- Remove other drivers from aperture
pixpaper:
- Add support for Mayqueen Pixpaper plus DT bindings
v3d:
- Support querying nubmer of GPU resets for KHR_robustness
stm:
- Clean up logging
- ltdc: Add support support for STM32MP257F-EV1 plus DT bindings
sitronix:
- st7571-i2c: Add support for inverted displays and 2-bit grayscale
tidss:
- Convert to kernel's FIELD_ macros
vesadrm:
- Support 8-bit palette mode
imagination:
- Improve power management
- Add support for TH1520 GPU
- Support Risc-V architectures
v3d:
- Improve job management and locking
vkms:
- Support variants of ARGB8888, ARGB16161616, RGB565, RGB888 and P01x
- Spport YUV with 16-bit components
-----BEGIN PGP SIGNATURE-----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=ZVKY
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2025-10-01' of https://gitlab.freedesktop.org/drm/kernel
Pull drm updates from Dave Airlie:
"cross-subsystem:
- i2c-hid: Make elan touch controllers power on after panel is
enabled
- dt bindings for STM32MP25 SoC
- pci vgaarb: use screen_info helpers
- rust pin-init updates
- add MEI driver for late binding firmware update/load
uapi:
- add ioctl for reassigning GEM handles
- provide boot_display attribute on boot-up devices
core:
- document DRM_MODE_PAGE_FLIP_EVENT
- add vendor specific recovery method to drm device wedged uevent
gem:
- Simplify gpuvm locking
ttm:
- add interface to populate buffers
sched:
- Fix race condition in trace code
atomic:
- Reallow no-op async page flips
display:
- dp: Fix command length
video:
- Improve pixel-format handling for struct screen_info
rust:
- drop Opaque<> from ioctl args
- Alloc:
- BorrowedPage type and AsPageIter traits
- Implement Vmalloc::to_page() and VmallocPageIter
- DMA/Scatterlist:
- Add dma::DataDirection and type alias for dma_addr_t
- Abstraction for struct scatterlist and sg_table
- DRM:
- simplify use of generics
- add DriverFile type alias
- drop Object::SIZE
- Rust:
- pin-init tree merge
- Various methods for AsBytes and FromBytes traits
gpuvm:
- Support madvice in Xe driver
gpusvm:
- fix hmm_pfn_to_map_order usage in gpusvm
bridge:
- Improve and fix ref counting on bridge management
- cdns-dsi: Various improvements to mode setting
- Support Solomon SSD2825 plus DT bindings
- Support Waveshare DSI2DPI plus DT bindings
- Support Content Protection property
- display-connector: Improve DP display detection
- Add support for Radxa Ra620 plus DT bindings
- adv7511: Provide SPD and HDMI infoframes
- it6505: Replace crypto_shash with sha()
- synopsys: Add support for DW DPTX Controller plus DT bindings
- adv7511: Write full Audio infoframe
- ite6263: Support vendor-specific infoframes
- simple: Add support for Realtek RTD2171 DP-to-HDMI plus DT bindings
panel:
- panel-edp: Support mt8189 Chromebooks; Support BOE NV140WUM-N64;
Support SHP LQ134Z1; Fixes
- panel-simple: Support Olimex LCD-OLinuXino-5CTS plus DT bindings
- Support Samsung AMS561RA01
- Support Hydis HV101HD1 plus DT bindings
- ilitek-ili9881c: Refactor mode setting; Add support for Bestar
BSD1218-A101KL68 LCD plus DT bindings
- lvds: Add support for Ampire AMP19201200B5TZQW-T03 to DT bindings
- edp: Add support for additonal mt8189 Chromebook panels
- lvds: Add DT bindings for EDT ETML0700Z8DHA
amdgpu:
- add CRIU support for gem objects
- RAS updates
- VCN SRAM load fixes
- EDID read fixes
- eDP ALPM support
- Documentation updates
- Rework PTE flag generation
- DCE6 fixes
- VCN devcoredump cleanup
- MMHUB client id fixes
- VCN 5.0.1 RAS support
- SMU 13.0.x updates
- Expanded PCIe DPC support
- Expanded VCN reset support
- VPE per queue reset support
- give kernel jobs unique id for tracing
- pre-populate exported buffers
- cyan skillfish updates
- make vbios build number available in sysfs
- userq updates
- HDCP updates
- support MMIO remap page as ttm pool
- JPEG parser updates
- DCE6 DC updates
- use devm for i2c buses
- GPUVM locking updates
- Drop non-DC DCE11 code
- improve fallback handling for pixel encoding
amdkfd:
- SVM/page migration fixes
- debugfs fixes
- add CRIO support for gem objects
- SVM updates
radeon:
- use dev_warn_once in CS parsers
xe:
- add madvise interface
- add DRM_IOCTL_XE_VM_QUERY_MEMORY_RANGE_ATTRS to query VMA count
and memory attributes
- drop L# bank mask reporting from media GT3 on Xe3+.
- add SLPC power_profile sysfs interface
- add configs attribs to add post/mid context-switch commands
- handle firmware reported hardware errors notifying userspace with
device wedged uevent
- use same dir structure across sysfs/debugfs
- cleanup and future proof vram region init
- add G-states and PCI link states to debugfs
- Add SRIOV support for CCS surfaces on Xe2+
- Enable SRIOV PF mode by default on supported platforms
- move flush to common code
- extended core workarounds for Xe2/3
- use DRM scheduler for delayed GT TLB invalidations
- configs improvements and allow VF device enablement
- prep work to expose mmio regions to userspace
- VF migration support added
- prepare GPU SVM for THP migration
- start fixing XE_PAGE_SIZE vs PAGE_SIZE
- add PSMI support for hw validation
- resize VF bars to max possible size according to number of VFs
- Ensure GT is in C0 during resume
- pre-populate exported buffers
- replace xe_hmm with gpusvm
- add more SVM GT stats to debugfs
- improve fake pci and WA kunnit handle for new platform testing
- Test GuC to GuC comms to add debugging
- use attribute groups to simplify sysfs registration
- add Late Binding firmware code to interact with MEI
i915:
- apply multiple JSL/EHL/Gen7/Gen6 workarounds properly
- protect against overflow in active_engine()
- Use try_cmpxchg64() in __active_lookup()
- include GuC registers in error state
- get rid of dev->struct_mutex
- iopoll: generalize read_poll_timout
- lots more display refactoring
- Reject HBR3 in any eDP Panel
- Prune modes for YUV420
- Display Wa fix, additions, and updates
- DP: Fix 2.7 Gbps link training on g4x
- DP: Adjust the idle pattern handling
- DP: Shuffle the link training code a bit
- Don't set/read the DSI C clock divider on GLK
- Enable_psr kernel parameter changes
- Type-C enabled/disconnected dp-alt sink
- Wildcat Lake enabling
- DP HDR updates
- DRAM detection
- wait PSR idle on dsb commit
- Remove FBC modulo 4 restriction for ADL-P+
- panic: refactor framebuffer allocation
habanalabs:
- debug/visibility improvements
- vmalloc-backed coherent mmap support
- HLDIO infrastructure
nova-core:
- various register!() macro improvements
- minor vbios/firmware fixes/refactoring
- advance firmware boot stages; process Booter and patch signatures
- process GSP and GSP bootloader
- Add r570.144 firmware bindings and update to it
- Move GSP boot code to own module
- Use new pin-init features to store driver's private data in a
single allocation
- Update ARef import from sync::aref
nova-drm:
- Update ARef import from sync::aref
tyr:
- initial driver skeleton for a rust driver for ARM Mali GPUs
- capable of powering up, query metadata and provide it to userspace.
msm:
- GPU and Core:
- in DT bindings describe clocks per GPU type
- GMU bandwidth voting for x1-85
- a623/a663 speedbins
- cleanup some remaining no-iommu leftovers after VM_BIND conversion
- fix GEM obj 32b size truncation
- add missing VM_BIND param validation
- IFPC for x1-85 and a750
- register xml and gen_header.py sync from mesa
- Display:
- add missing bindings for display on SC8180X
- added DisplayPort MST bindings
- conversion from round_rate() to determine_rate()
amdxdna:
- add IOCTL_AMDXDNA_GET_ARRAY
- support user space allocated buffers
- streamline PM interfaces
- Refactoring wrt. hardware contexts
- improve error reporting
nouveau:
- use GSP firmware by default
- improve error reporting
- Pre-populate exported buffers
ast:
- Clean up detection of DRAM config
exynos:
- add DSIM bridge driver support for Exynos7870
- Document Exynos7870 DSIM compatible in dt-binding
panthor:
- Print task/pid on errors
- Add support for Mali G710, G510, G310, Gx15, Gx20, Gx25
- Improve cache flushing
- Fail VM bind if BO has offset
renesas:
- convert to RUNTIME_PM_OPS
rcar-du:
- Make number of lanes configurable
- Use RUNTIME_PM_OPS
- Add support for DSI commands
rocket:
- Add driver for Rockchip NPU plus DT bindings
- Use kfree() and sizeof() correctly
- Test DMA status
rockchip:
- dsi2: Add support for RK3576 plus DT bindings
- Add support for RK3588 DPTX output
tidss:
- Use crtc_ fields for programming display mode
- Remove other drivers from aperture
pixpaper:
- Add support for Mayqueen Pixpaper plus DT bindings
v3d:
- Support querying nubmer of GPU resets for KHR_robustness
stm:
- Clean up logging
- ltdc: Add support support for STM32MP257F-EV1 plus DT bindings
sitronix:
- st7571-i2c: Add support for inverted displays and 2-bit grayscale
tidss:
- Convert to kernel's FIELD_ macros
vesadrm:
- Support 8-bit palette mode
imagination:
- Improve power management
- Add support for TH1520 GPU
- Support Risc-V architectures
v3d:
- Improve job management and locking
vkms:
- Support variants of ARGB8888, ARGB16161616, RGB565, RGB888 and P01x
- Spport YUV with 16-bit components"
* tag 'drm-next-2025-10-01' of https://gitlab.freedesktop.org/drm/kernel: (1455 commits)
drm/amd: Add name to modes from amdgpu_connector_add_common_modes()
drm/amd: Drop some common modes from amdgpu_connector_add_common_modes()
drm/amdgpu: update MODULE_PARM_DESC for freesync_video
drm/amd: Use dynamic array size declaration for amdgpu_connector_add_common_modes()
drm/amd/display: Share dce100_validate_global with DCE6-8
drm/amd/display: Share dce100_validate_bandwidth with DCE6-8
drm/amdgpu: Fix fence signaling race condition in userqueue
amd/amdkfd: enhance kfd process check in switch partition
amd/amdkfd: resolve a race in amdgpu_amdkfd_device_fini_sw
drm/amd/display: Reject modes with too high pixel clock on DCE6-10
drm/amd: Drop unnecessary check in amdgpu_connector_add_common_modes()
drm/amd/display: Only enable common modes for eDP and LVDS
drm/amdgpu: remove the redeclaration of variable i
drm/amdgpu/userq: assign an error code for invalid userq va
drm/amdgpu: revert "rework reserved VMID handling" v2
drm/amdgpu: remove leftover from enforcing isolation by VMID
drm/amdgpu: Add fallback to pipe reset if KCQ ring reset fails
accel/habanalabs: add Infineon version check
accel/habanalabs/gaudi2: read preboot status after recovering from dirty state
accel/habanalabs: add HL_GET_P_STATE passthrough type
...
Call drm_mode_size_dumb() to compute dumb-buffer scanline pitch and
buffer size. Align the pitch to a multiple of 64.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Cc: Sandy Huang <hjc@rock-chips.com>
Cc: "Heiko Stübner" <heiko@sntech.de>
Cc: Andy Yan <andy.yan@rock-chips.com>
Link: https://lore.kernel.org/r/20250821081918.79786-20-tzimmermann@suse.de
-----BEGIN PGP SIGNATURE-----
iQFSBAABCgA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmjHMcoeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG5bwH/23w8iGB4hf7L/7Z
e7blX42Pe9EXA1uK62iWmwEjDvBuJ7TmVfXH09qYJ56fj6/rJEdpQwtBMd4ypL81
QA/7lq5UEl0apPzMN86J8EHCzmjNzv7o+UtEd4C/hPFEZHZJa5Hqj9CBglSwSCEn
fTkLk7Gl6s8SfzBQ/rXX6/ZChAB/RleVWabDlIQMDz++/+9DZ0aqphj+5bYSqysL
ROQOaj4LOICuLfrup9J61hKNBoF7Dv3sO20vc+Iic0XHRPZ6/lKCnHgCUsqVIOOQ
L4kDT7XKQg+n3ttjrMe84/8iHZdWtf8VMWrtniPT8e1YGYuMpavVplgIcFoFCoNm
Qa7NPDs=
=rZeT
-----END PGP SIGNATURE-----
Merge tag 'v6.17-rc6' into drm-next
This is a backmerge of Linux 6.17-rc6, needed for msm,
also requested by misc.
Signed-off-by: Dave Airlie <airlied@redhat.com>
The era of hand-rolled HIWORD_UPDATE macros is over, at least for those
drivers that use constant masks.
Remove this driver's very own HIWORD_UPDATE macro, and replace all
instances of it with equivalent instantiations of FIELD_PREP_WM16 or
FIELD_PREP_WM16_CONST, depending on whether it's in an initializer.
This gives us better error checking, and a centrally agreed upon
signature for this macro, to ease in code comprehension.
Because FIELD_PREP_WM16/FIELD_PREP_WM16_CONST shifts the value to the
mask (like FIELD_PREP et al do), a lot of macro instantiations get
easier to read.
This was tested on an RK3568 ODROID M1, as well as an RK3399 ROCKPro64.
Reviewed-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Tested-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Signed-off-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Yury Norov (NVIDIA) <yury.norov@gmail.com>
The era of hand-rolled HIWORD_UPDATE macros is over, at least for those
drivers that use constant masks.
The inno-hdmi driver's own HIWORD_UPDATE macro is instantiated only
twice. Remove it, and replace its uses with FIELD_PREP_WM16. Since
FIELD_PREP_WM16 shifts the value for us, we replace using the mask as
the value by simply using 1 instead.
With the new FIELD_PREP_WM16 macro, we gain better error checking and a
central shared definition.
This has been compile-tested only as I lack hardware this old, but the
change is trivial enough that I am fairly certain it's equivalent.
Signed-off-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Yury Norov (NVIDIA) <yury.norov@gmail.com>
The era of hand-rolled HIWORD_UPDATE macros is over, at least for those
drivers that use constant masks.
Replace this driver's HIWORD_UPDATE with the FIELD_PREP_WM16 macro from
hw_bitfield.h. While at it, disambiguate the GRF write to SOC_CON7 by
splitting the definition into the individual bitflags. This is done
because FIELD_PREP_WM16 shifts the value for us according to the mask,
so writing the mask to itself to enable two bits is no longer something
that can be done. It should also not be done anyway because it hides the
true meaning of those two individual bit flags.
HDMI output with this patch has been tested on both RK3588 and RK3576.
On the former, with both present HDMI connectors.
Reviewed-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Tested-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Signed-off-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Yury Norov (NVIDIA) <yury.norov@gmail.com>
The era of hand-rolled HIWORD_UPDATE macros is over, at least for those
drivers that use constant masks.
Remove VOP2's HIWORD_UPDATE macro from the vop2 header file, and replace
all instances in rockchip_vop2_reg.c (the only user of this particular
HIWORD_UPDATE definition) with equivalent FIELD_PREP_WM16 instances. This
gives us better error checking.
Reviewed-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Tested-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Signed-off-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Yury Norov (NVIDIA) <yury.norov@gmail.com>
The era of hand-rolled HIWORD_UPDATE macros is over, at least for those
drivers that use constant masks.
Remove this driver's HIWORD_UPDATE macro, and replace instances of it
with either FIELD_PREP_WM16 or FIELD_PREP_WM16_CONST, depending on
whether they're in an initializer. This gives us better error checking,
which already saved me some trouble during this refactor.
The driver's HIWORD_UPDATE macro doesn't shift up the value, but expects
a pre-shifted value. Meanwhile, FIELD_PREP_WM16 and
FIELD_PREP_WM16_CONST will shift the value for us, based on the given
mask. So a few things that used to be a HIWORD_UPDATE(VERY_LONG_FOO,
VERY_LONG_FOO) are now a somewhat more pleasant
FIELD_PREP_WM16(VERY_LONG_FOO, 1).
There are some non-trivial refactors here. A few literals needed a UL
suffix added to stop them from unintentionally overflowing as a signed
long. To make sure all of these cases are caught, and not just the ones
where the FIELD_PREP_WM16* macros use such a value as a mask, just mark
every literal that's used as a mask as unsigned.
Non-contiguous masks also have to be split into multiple
FIELD_PREP_WM16* instances, as the macro's checks and shifting logic
rely on contiguous masks.
This is compile-tested only.
Signed-off-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Yury Norov (NVIDIA) <yury.norov@gmail.com>
The era of hand-rolled HIWORD_UPDATE macros is over, at least for those
drivers that use constant masks.
Remove rockchip_lvds.h's own HIWORD_UPDATE macro, and replace all
instances of it with hw_bitfield.h's FIELD_PREP_WM16 macro, which gives
us more error checking.
For the slightly-less-trivial case of the 2-bit width instance, the
results were checked during development to match all possible input
values (0 to 3, inclusive).
Signed-off-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Yury Norov (NVIDIA) <yury.norov@gmail.com>
Add driver extension for Synopsys DesignWare DPTX IP used
on Rockchip RK3588 SoC.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Acked-by: Dmitry Baryshkov <lumag@kernel.org>
Tested-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250822063959.692098-4-andyshrk@163.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Add the necessary specific bits to support the rk3576-variant of the
DW-DSI2 controller.
Signed-off-by: Guochun Huang <hero.huang@rock-chips.com>
[adapted from the vendor-kernel for mainline]
Reviewed-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250707164906.1445288-10-heiko@sntech.de
Make video port registers nonvolatile. As DSP_CTRL register is written
to twice due to gamma LUT enable bit which is set outside of the main
DSP_CTRL initialization within atomic_enable (for rk356x case it is also
necessary to always disable gamma LUT before writing a new LUT) there is
a chance that DSP_CTRL value read-out in gamma LUT init/update code is
not the one which was written by the preceding DSP_CTRL initialization
code within atomic_enable. This might result in misconfigured DSP_CTRL
which leads to no visual output[1]. Since DSP_CTRL write takes effect
after VSYNC[1] the issue is not always present. When tested on Pinetab2
with kernel 6.14 it happenes only when DRM is compiled as a module[1].
In order to confirm that it is a timing issue I inserted 18ms udelay
before vop2_crtc_atomic_try_set_gamma in atomic enable and compiled DRM
as module - this has also fixed the issue.
[1] https://lore.kernel.org/linux-rockchip/562b38e5.a496.1975f09f983.Coremail.andyshrk@163.com/
Reported-by: Diederik de Haas <didi.debian@cknow.org>
Closes: https://lore.kernel.org/linux-rockchip/DAEVDSTMWI1E.J454VZN0R9MA@cknow.org/
Suggested-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Piotr Zalewski <pZ010001011111@proton.me>
Tested-by: Diederik de Haas <didi.debian@cknow.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250706083629.140332-2-pZ010001011111@proton.me
Pass along the format info from .fb_create() to aliminate the
redundant drm_get_format_info() calls from the afbc code.
Cc: Sandy Huang <hjc@rock-chips.com>
Cc: "Heiko Stübner" <heiko@sntech.de>
Cc: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250701090722.13645-9-ville.syrjala@linux.intel.com
Pass along the format info from .fb_create() to eliminate the
redundant drm_get_format_info() calls from the gem fb code.
v2: Fix kernel docs (Laurent)
Cc: Dave Airlie <airlied@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Sandy Huang <hjc@rock-chips.com>
Cc: "Heiko Stübner" <heiko@sntech.de>
Cc: Andy Yan <andy.yan@rock-chips.com>
Cc: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Cc: virtualization@lists.linux.dev
Cc: spice-devel@lists.freedesktop.org
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250701090722.13645-8-ville.syrjala@linux.intel.com
In some application scenarios, we hope to get the corresponding
connector when the bridge's detect hook is invoked.
In most cases, we can get the connector by drm_atomic_get_connector_for_encoder
if the encoder attached to the bridge is enabled, however there will
still be some scenarios where the detect hook of the bridge is called
but the corresponding encoder has not been enabled yet. For instance,
this occurs when the device is hot plug in for the first time.
Since the call to bridge's detect is initiated by the connector, passing
down the corresponding connector directly will make things simpler.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250703125027.311109-3-andyshrk@163.com
[DB: added the chunk to the cdn-dp driver]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Make the dp/hdmi_audio_* callback maintain the same parameter order as
get_modes and edid_read: first the bridge, then the connector.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250703125027.311109-2-andyshrk@163.com
[DB: added the chunk to the cdn-dp driver]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
The all video ports of rk3568/rk3588 share the same OVL_LAYER_SEL
and OVL_PORT_SEL registers, and the configuration of these two registers
can be set to take effect when the vsync signal arrives at a certain Video
Port.
If two threads for two display output choose to update these two registers
simultaneously to meet their own plane adjustment requirements(change plane
zpos or switch plane from one crtc to another), then no matter which Video
Port'svsync signal we choose to follow for these two registers, the display
output of the other Video Port will be abnormal.
This is because the configuration of this Video Port does not take
effect at the right time (its configuration should take effect when its
VSYNC signal arrives).
In order to solve this problem, when performing plane migration or
change the zpos of planes, there are two things to be observed and
followed:
1. When a plane is migrated from one VP to another, the configuration of
the layer can only take effect after the Port mux configuration is
enabled.
2. When change the zpos of planes, we must ensure that the change for
the previous VP takes effect before we proceed to change the next VP.
Otherwise, the new configuration might overwrite the previous one for
the previous VP, or it could lead to the configuration of the previous
VP being take effect along with the VSYNC of the new VP.
This issue only occurs in scenarios where multi-display output is enabled.
Fixes: c5996e4ab1 ("drm/rockchip: vop2: Make overlay layer select register configuration take effect by vsync")
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250421102156.424480-1-andyshrk@163.com
Make use of devm_clk_get_enabled() to replace devm_clk_get() and
clk_prepare_enable(), which will make the cleanup of clk code simpler.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250512124615.2848731-9-andyshrk@163.com
