[Why & How]
Function logic should put after variable declare section, so let's move it.
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Chuanyu Tseng <Chuanyu.Tseng@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why/How]
UrgLatency value is passed in twice to the prefetch calculations.
Once through the UrgentLatency term and once through the Turg term.
Only Turg is used in the prefetch calculation so remove the unused UrgentLatency parameter
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Zheng, Austin <Austin.Zheng@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The MinTTU policy in DML2.1 does not guarantee that we support p-state
in blank. This is a delta vs dml2 and earlier revisions as the prefetch
mode override has been removed in favor of a more configurable pstate
optimizer.
[How]
Split off DCN42 with its own PMO helpers so that we can use a simpler
strategy of only allowing the mode if we support p-state in vblank and
if vactive has enough latency hiding.
The actual hookup to use these helpers in the PMO factory will be
done in a later patch to satisfy build system requirements.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Memory latencies are soc specific and should be part of dml soc
bounding box. This change removes them from clk_mgr and has
latency update happen based on memory type when dml socbb is being
updated.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Dmytro Laktyushkin <dmytro.laktyushkin@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]: Implicit narrowing of wider integer types (unsigned int, uint64_t)
into narrower fields (uint8_t, uint16_t, unsigned short) has potential
truncation issues.
[How]: For each warning site, added ASSERT(<value> <= 0xFFFF/0xFF) for
debug-mode bounds verification followed by an explicit cast. Typed
intermediate variables introduced where needed for clarity.
No functional change intended.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Gaghik Khachatrian <gaghik.khachatrian@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add latency update based on memory type to dml2.1
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Dmytro Laktyushkin <dmytro.laktyushkin@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
To match the HW specification this should be 4, not 256.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Like dml2_0 this isn't guaranteed to be constant for every ASIC.
This can cause corruption or underflow for linear surfaces due to a
wrong PTE_ROW_HEIGHT_LINEAR value if not correctly specified.
[How]
Like dml2_0 pass in the SOC bb into the plane configuration population
functions.
Set both GPUVM and HostVM page sizes in the overrides.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
The MALL and DCC parameters were copied and pasted from a previous ASIC
but the correct value per HW specification should all be 0.
If not correct this can impact urgent bandwidth calculation and PMO.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This was found back on DML2 but was missed when creating DML2.1.
The bottom layer calculation (CalculateHostVMDynamicLevels) expects
a value in bytes, not KB, but we pass in the value in KB (eg. 4).
This causes an extra page table level to be required in the prefetch
bytes which can be significant overhead - preventing some modes
from being supported that should otherwise be.
[How]
Correct the units by multiplying the input and override values by 1024.
Reviewed-by: Austin Zheng <austin.zheng@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We don't have to do MCCS/DDCCI transactions with sink side every time by calling
get_modes(). Limit it to be operated when hotplug occurs.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If sink like HDMI indicates supporting freesync via MCCS,
explicitly to send vcp set command on sink to enable freesync.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If EDID AMD VSDB declares that sink supports MCCS method for freesync
usage, send mccs request to understand sink freesync current supporting
state.
If sink supports freesync but user toggles OSD to turn off it, disable
freesync.
If HDMI sink doesn't support MCCS method for freesync usage, disable
freesync as well.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
DMUB supports to parse freesynce mccs vcp code now. Store it for
later freesync mccs manipulation.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add more freesync supported pcon ID into the whitelist.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why/How]
A workaround was previously used for certain Freesync cases that would
override the vstartup_start value from DML to position the SDP
correctly. This is no longer needed in DCN32 and above, so remove the
workaround.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Reworked YCbCr4:2:2 Native/Simple policy decision making with DSC
enabled based on DSC caps and stream signal type
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Relja Vojvodic <Relja.Vojvodic@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
update according hw spec.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Remove unused legacy tiling format support from dml2.
Legacy asics don't use dml2.
Fixes: e56e3cff2a ("drm/amd/display: Sync dcn42 with DC 3.2.373")
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why] Resolve warnings by marking unused parameters explicitly.
[How] Keep parameter names in signatures and add a line with
'(void)param;' inside the function body
Preserved function signatures and avoids breaking code paths that
may reference the parameter under conditional compilation.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Reviewed-by: Clayton King <clayton.king@amd.com>
Signed-off-by: Gaghik Khachatrian <gaghik.khachatrian@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This code waits for the MES self-test to complete by repeatedly checking
a register or memory value until it becomes valid or a timeout occurs.
The fix ensures the timeout counter works correctly by not reusing the
same variable inside another loop.
mes_v12_1_test_ring() uses 'i' as the outer timeout loop counter, but
reuses the same variable for the inner XCC scan in cooperative mode.
This makes the timeout counter ambiguous and can lead to incorrect
timeout handling. It also triggers a Smatch warning about reusing the
outer loop iterator.
Fix this by introducing a separate iterator for the inner XCC loop so
that 'i' continues to represent only the timeout wait duration.
drivers/gpu/drm/amd/amdgpu/mes_v12_1.c:2080 mes_v12_1_test_ring()
warn: reusing outside iterator: 'i'
drivers/gpu/drm/amd/amdgpu/mes_v12_1.c
2069 atomic64_set((atomic64_t *)wptr_cpu_addr, wptr);
2070 WDOORBELL64(doorbell_idx, wptr);
2071
2072 for (i = 0; i < adev->usec_timeout; i++) {
i is counting usec
2073 if (queue_type == AMDGPU_RING_TYPE_SDMA) {
2074 tmp = le32_to_cpu(*cpu_ptr);
2075 } else {
2076 if (!adev->mes.enable_coop_mode) {
2077 tmp = RREG32_SOC15(GC, GET_INST(GC, xcc_id),
2078 regSCRATCH_REG0);
2079 } else {
--> 2080 for (i = 0; i < num_xcc; i++) {
and then re-used to count something else
Fixes: 44e5195fa3 ("drm/amdgpu/mes_v12_1: add mes self test")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Cc: Jack Xiao <Jack.Xiao@amd.com>
Cc: Hawking Zhang <Hawking.Zhang@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Jack Xiao <Jack.Xiao@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Extend the smu_cmn_update_table function to support reading a 32-bit return
argument from the SMU firmware during table transfer operations.
- Rename the original function to smu_cmn_update_table_read_arg
- Add a uint32_t *read_arg output parameter to capture firmware response
- Pass the read_arg pointer to the SMU message command
- Keep full backward compatibility using a macro wrapper for the old API
This allows the driver to retrieve status codes, results, or configuration
feedback from the SMU firmware after table data transfer.
No functional changes for existing users of the original smu_cmn_update_table()
API.
Signed-off-by: Yang Wang <kevinyang.wang@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix runtime PM counter imbalance to prevent device from failing to enter low power state
Fixes: a50d32c41f ("drm/amd/pm: Deprecate print_clock_levels interface")
Signed-off-by: Yang Wang <kevinyang.wang@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Plumb in support for disabling kernel queues and make it
the default. For testing, kernel queues can be re-enabled
by setting amdgpu.user_queue=0. Kernel queues are still
created for use by the kernel driver for memory management,
etc., just not user submissions.
Reviewed-by: Prike Liang <Prike.Liang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cyan skillfish uses IP discovery v0. This was broken when the
IP discovery was refactored for newer versions.
Closes: https://gitlab.freedesktop.org/drm/amd/-/work_items/5189
Fixes: d0c647a6aa ("drm/amdgpu/discovery: support new discovery binary header")
Signed-off-by: filippor <filippo.rossoni@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
aldebaran_mode2_reset() sends a mode2 reset message and waits for
an acknowledgment from the SMU.
The current ACK handling is incorrect.
The wait loop runs only when ret is -ETIME. But after a successful
async send, ret is 0. Because of this, the loop is skipped and the
code does not wait for the reset acknowledgment.
Also, the code checks for ret != 1 after calling
smu_msg_wait_response(). However, smu_msg_wait_response() returns
0 on success and negative error codes on failure. So checking
against 1 is wrong.
Return -EOPNOTSUPP when the firmware does not support this reset
message.
Fix this by setting ret to -ETIME before entering the wait loop,
checking for ret != 0 after getting the SMU response, and returning
-EOPNOTSUPP when the firmware does not support the message.
v2:
- Update ACK check to use ret != 0 instead of ret != 1, since
smu_msg_wait_response() returns 0 on success (Feifei)
- Remove unnecessary handling for ret == 0
Fixes: e42569d02a ("drm/amd/pm: Modify mode2 msg sequence on aldebaran")
Reported-by: Dan Carpenter <error27@gmail.com>
Cc: Feifei Xu <Feifei.Xu@amd.com>
Cc: Lijo Lazar <lijo.lazar@amd.com>
Cc: Hawking Zhang <Hawking.Zhang@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
smu7_hwmgr_backend_init() is responsible for initializing the SMU7 power
management backend. It allocates and sets up the backend structure,
initializes voltage tables, configures dependency tables, and prepares
platform-specific power and clock parameters.
The function follows a typical pattern where each initialization step
returns a status in "result", and failures are handled via a common
"goto fail" path that performs cleanup.
Commit 2c21648bb814 ("drm/amd/pm/smu7: Remove non-functional SMU7
voltage dependency on DAL") removed a function call in this
initialization sequence, but left behind the corresponding error check.
As a result, "result" is checked twice without being updated in between:
result = smu7_init_voltage_dependency_on_display_clock_table(hwmgr);
if (result)
goto fail;
...
if (result)
goto fail;
The second check is redundant and unreachable for any new failure, since
no operation modifies "result" between the two checks. This triggers a
Smatch warning about a duplicate zero check and reduces code clarity.
Remove the stale error check to keep the control flow correct and
readable.
Fixes: 9f49e3d4cb ("drm/amd/pm/smu7: Remove non-functional SMU7 voltage dependency on DAL")
Reported-by: Dan Carpenter <error27@gmail.com>
Cc: Timur Kristóf <timur.kristof@gmail.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
VF sends IDH_REQ_GPU_FINI_ACCESS before hw_fini during unload.
PF no longer accepts requests, so skip ECC status update to prevent
mailbox timeout.
Signed-off-by: Ce Sun <cesun102@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
amdgpu_cper_ring_get_ent_sz() parses CPER headers directly from the
circular ring buffer to determine the current entry size. When the ring
is full and the write pointer lands near the end of the buffer, the
header can wrap across the ring boundary.
The existing code treats the 4-byte CPER signature as a C string and
uses strcmp() on in-ring binary data, then reads record_length through a
direct struct pointer cast. Both assumptions are unsafe for wrapped
entries and can read past the end of the ring mapping.
Fix the parser by comparing the signature as raw bytes and by copying
the header into a local buffer before reading record_length, handling
wraparound explicitly in both cases. This avoids out-of-bounds reads in
amdgpu_cper_ring_get_ent_sz() when the CPER ring is full or the current
entry starts at the tail of the ring.
Signed-off-by: Xiang Liu <xiang.liu@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The off variable in the ring content dump loop tracks a byte offset
accumulated from ring->ring_size (which is in bytes), but it is used
as an index into u32 *rings_dw. C pointer arithmetic on a u32 pointer
automatically multiplies the index by sizeof(u32) = 4, so the actual
byte address accessed is:
&rings_dw[off] == (char *)rings_dw + off * 4
This means off is effectively quadrupled, causing a 4x overshoot.
Concrete example -- two rings, each ring_size = 8 192 bytes (8 KB):
total_ring_size = 16 384 bytes
rings_dw = kzalloc(16 384) /* 16 KB buffer */
Ring 0: off = 0
memcpy(&rings_dw[0], ring0->ring, 8192)
-> writes bytes 0 .. 8 191 OK
off += ring->ring_size -> off = 8 192 (BUG)
Ring 1: off = 8 192
memcpy(&rings_dw[8192], ring1->ring, 8192)
-> actual byte offset = 8 192 * 4 = 32 768
-> writes bytes 32 768 .. 40 959
-> but buffer is only 16 384 bytes! OVERFLOW
With the fix (off += ring->ring_size / 4):
Ring 0: off = 0
memcpy(&rings_dw[0], ring0->ring, 8192) OK
off += 8 192 / 4 -> off = 2 048
Ring 1: off = 2 048
memcpy(&rings_dw[2048], ring1->ring, 8192)
-> byte offset = 2 048 * 4 = 8 192
-> writes bytes 8 192 .. 16 383 OK
KASAN catches the overflow as a slab-use-after-free when the write
lands on a quarantined slab object:
BUG: KASAN: slab-use-after-free in amdgpu_coredump+0x775/0x13c0 [amdgpu]
Write of size 8192 at addr ffff8890b2400000 by task kworker/u128:1/329
Workqueue: amdgpu-reset-dev drm_sched_job_timedout [gpu_sched]
Call Trace:
__asan_memcpy+0x3c/0x60
amdgpu_coredump+0x775/0x13c0 [amdgpu]
amdgpu_job_timedout+0xdb5/0x1420 [amdgpu]
The corrupted object was a 4 KB drm_exec buffer from a completed
amdgpu_cs_ioctl -- the ring dump memcpy overshot into this freed
slab region.
Fix by accumulating off in dword units (ring->ring_size / 4) so the
u32* indexing produces the correct byte address. The reader in
amdgpu_devcoredump_format() already consumes the stored offset as a
dword index (rings_dw[off + j / 4]), so no change is needed there.
Fixes: eea85914d1 ("drm/amdgpu: save ring content before resetting the device")
Cc: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Jesse Zhang <jesse.zhang@amd.com>
Signed-off-by: Vitaly Prosyak <vitaly.prosyak@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For triggering the dpc event with a single device, we still need
to set the in_link_reset flag and the dpc status.
Signed-off-by: Ce Sun <cesun102@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
A race condition in the devcoredump code causes a NULL pointer
dereference in amdgpu_devcoredump_format() when multiple GPU resets
occur in quick succession.
The sequence of events:
1. First reset calls amdgpu_coredump(), creates coredump1, sets
adev->coredump = coredump1, and queues the deferred work.
2. The deferred work begins executing (work_pending() returns false
since the work is now running, not just queued).
3. A second reset calls amdgpu_coredump(). work_pending() returns
false because the work is running, so amdgpu_coredump() proceeds:
creates coredump2, overwrites adev->coredump = coredump2, and
re-queues the deferred work with queue_work().
4. The first deferred work finishes and unconditionally sets
adev->coredump = NULL, destroying the reference to coredump2.
5. The re-queued deferred work starts and reads
adev->coredump = NULL. It then passes this NULL into
amdgpu_devcoredump_format() which dereferences coredump->adev
(offset 0 in the struct), triggering:
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
RIP: 0010:amdgpu_devcoredump_format+0xa6/0x36b0 [amdgpu]
This was observed during the amd_deadlock IGT test where multiple
subtests trigger rapid ring resets. The dmesg log shows four
coredumps created within 120ms (at 102.377s, 104.424s, 104.492s,
and 104.497s), with the crash occurring 13ms after the last one.
Fix this with two changes:
- Replace work_pending() with work_busy() in amdgpu_coredump() to
also reject new coredumps while the deferred work is executing,
not just when it is queued. This closes the main race window.
- Add a defensive NULL check for adev->coredump at the start of
amdgpu_devcoredump_deferred_work() to prevent the crash if the
race still occurs (work_busy() is advisory, not a full barrier).
v2: Drop the job->pasid NULL guard -- that fix was independently
submitted and merged as commit 4c1f0a162da5 ("drm/amdgpu: add
job->pasid in check as amdgpu_job could be NULL") by Sunil
Khatri, reviewed by Christian König. Integrate with that
patch as suggested by Christian.
Fixes: 4bbba79a7f ("drm/amdgpu: move devcoredump generation to a worker")
Cc: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Vitaly Prosyak <vitaly.prosyak@amd.com>
Reviewed-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
KFD VRAM allocations set AMDGPU_GEM_CREATE_VRAM_WIPE_ON_RELEASE
but not AMDGPU_GEM_CREATE_VRAM_CLEARED, leaving freshly allocated
VRAM with stale data from prior use observable by compute kernels.
The GEM ioctl path already sets VRAM_CLEARED for all userspace
allocations via amdgpu_gem_create_ioctl() and
amdgpu_mode_dumb_create(). The KFD path was missing this flag,
allowing stale page table remnants to leak into user buffers.
This causes crashes in RCCL P2P transport where non-zero data in
ptrExchange/head/tail fields corrupts the protocol handshake.
Signed-off-by: Amir Shetaia <Amir.Shetaia@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Define and use regRCC_STRAP0_RCC_DEV0_EPF0_STRAP0_nbif_4_10,
to get correct rev_id in nbif_v6_3_1_get_rev_id().
Reviewed-by: Pratik Vishwakarma <Pratik.Vishwakarma@amd.com>
Signed-off-by: Ramalingeswara Reddy, Kanala <Kanala.RamalingeswaraReddy@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
PSP v15.0.0 needs both TOC and TA firmware. Without the declaration
it won't get included in initramfs and leads to following failure:
```
Direct firmware load for amdgpu/psp_15_0_0_ta.bin failed with error -2
early_init of IP block <psp> failed -19
Fatal error during GPU init
```
Fixes: 9b24f63d82 ("drm/amdgpu: Enable support for PSP 15_0_0")
Reviewed-by: Pratik Vishwakarma <Pratik.Vishwakarma@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
PCTL0__MMHUB_DEEPSLEEP_IB is 0x69004 on MMHUB 4,1,0 and
and 0x60804 on MMHUB 4,2,0. 0x62a04 is on MMHUB 1,8,0/1.
The DS bits are adjusted to cover more JPEG engines and MMHUB
version.
Signed-off-by: David (Ming Qiang) Wu <David.Wu3@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
During GPU reset, the application could still run CPU page table updates. Each commit called
amdgpu_device_flush_hdp(), which on SR-IOV sends work through the KIQ ring.
That can advance sync_seq while the GPU is being reset,
leaving fence writeback out of sync and causing amdgpu_fence_emit_polling()
to time out on later KIQ use.
Fix:
amdgpu_vm_cpu_commit():
Reset will flush HDP anyway, the HDP flush in amdgpu_vm_cpu_commit() can be skipped
when a reset is ongoging.
Take reset_domain->sem with down_read_trylock() before amdgpu_device_flush_hdp().
If the reset path holds the write lock, skip the HDP flush so no HDP-related HW
access (including KIQ) runs during reset; state is re-established after reset.
Signed-off-by: Chenglei Xie <Chenglei.Xie@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Define and use regGOLDEN_TSC_COUNT_UPPER_smu_15_0_0 and
regGOLDEN_TSC_COUNT_LOWER_smu_15_0_0 for TSC upper and lower count.
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Pratik Vishwakarma <Pratik.Vishwakarma@amd.com>
Signed-off-by: Ramalingeswara Reddy, Kanala <Kanala.RamalingeswaraReddy@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Module reload would fail when create sys file that was not removed during
module unload.
Fixes: e0e9792ea2 ("drm/amdgpu: add an option to allow gpu partition allocate all available memory")
Signed-off-by: Xiaogang Chen <xiaogang.chen@amd.com>
Reviewed-by: Philip Yang <philip.yang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
OverDriveTable.FanMinimumPwm and FeatureCtrlMask.PP_OD_FEATURE_FAN_LEGACY_BIT
have a hard dependency.
Invalid handling of this dependency leads to disabled thermal monitoring
and temperature boundary validation.
v2: squash in typo fix (Yang)
Fixes: 9710b84e2a ("drm/amd/pm: add overdrive support on smu v14.0.2/3")
Cc: stable@vger.kernel.org
Signed-off-by: Yang Wang <kevinyang.wang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/i915/display: change pipe allocation order for discrete platforms
This is a topic pull request for changing the pipe allocation order for
discrete platforms from the usual A,B,C,D to A,C,B,D. The goal is to
help pipe joiner configurations that reserve the adjacent pipe as the
secondary pipe without the user space knowing. More details in the
relevant commit message. The CRTC iteration is also changed to remain in
pipe order.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Jani Nikula <jani.nikula@intel.com>
Link: https://patch.msgid.link/d69501d53c233386d70ed10290af24aafebf434f@intel.com
When big joiner is enabled, it reserves the adjacent pipe as the
secondary pipe. This happens without the user space knowing, and
subsequent attempts at using the CRTC with that pipe will fail. If the
user space does not have a coping mechanism, i.e. trying another CRTC,
this leads to a black screen.
Try to reduce the impact of the problem on discrete platforms by mapping
the CRTCs to pipes in order A, C, B, and D. If the user space reserves
CRTCs in order, this should trick it to using pipes that are more likely
to be available for and after joining.
Limit this to discrete platforms, which have four pipes, and no eDP, a
combination that should benefit the most with least drawbacks.
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20260413081609.969342-1-jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
VESA backlight enable is possible when
BACKLIGHT_AUX_ENABLE_CAPABLE is true via AUX command or when
BACKLIGHT_PIN_ENABLE_CAPABLE is true via eDP connector pin.
Similarly, backlight brightness adjustment can be
done via AUX-based control or PWM pin-based control.
It means there can be three configurations:
1) Full AUX-based: Enable and adjustment both via AUX. We currently
support this (apart from the AUX luminance-based backlight control).
2) Hybrid: Enable via the BL_ENABLE pin, adjustment via either AUX or
PWM.
3) Fully PWM pin-based: Enable via the BL_ENABLE pin, adjustment via
PWM.
Since that only 1 is supported as of now we need to make
sure we do not try to manipulate backlight when
BACKLIGHT_AUX_ENABLE_CAPABLE is not set.
Also fix return value when condition is not fulfilled.
Closes: https://gitlab.freedesktop.org/drm/i915/kernel/-/work_items/15907
Fixes: 0fb03890d1 ("drm/i915/backlight: Check if VESA backlight is possible")
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patch.msgid.link/20260407030710.1440046-1-suraj.kandpal@intel.com
(cherry picked from commit 102d44b3a8)
Signed-off-by: Tvrtko Ursulin <tursulin@ursulin.net>
Currently our crtcs are registered in pipe order, and thus
all the for_intel_crtc*() iterators walk the crtcs in pipe
order. There are a bunch of places that more or less depend
on that. Eg. during plane updates and such we want joined
pipes to be processed back-to-back to give a better chance
of an atomic update across the whole set.
When we start to register crtcs in a different order we don't
want to change the order in which the pipes get handled.
Decouple the for_each_intel_crtc*() iterators from the crtc
registration order by using a separate list which will be
sorted by the pipe rather than the crtc index.
We could probably use a simple array or something, but that
would require some kind of extra iterator variable for the
macros, and thus would require a lot more changes. Using
a linked list keeps the fallout minimal. We can look at
using a more optimal data structure later.
I also added this extra junk to the atomic state iterators:
"(__i) = drm_crtc_index(&(crtc)->base), (void)(__i)"
even though the macro itself no longer needs the "__i" iterator.
This in case the "__i" is used by the caller, and to
avoid compiler warnings if it's completely unused now.
v2: Flip the pipe comparison (Jani)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20260408155744.13326-3-ville.syrjala@linux.intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
