Add a generic PHY driver for the TI DS125DF111 Multi-Protocol
Dual-Channel Retimer. The driver currently supports only 10G and 1G link
speeds but it can easily extended to also cover other usecases.
Since the available datasheet (https://www.ti.com/lit/gpn/DS125DF111)
does not name the registers, the name for the macros were determined by
their usage pattern.
A PHY device is created for each of the two channels present on the
retimer. This allows for independent configuration of the two channels.
This capability is especially important on retimers which have more than
2 channels that can be, depending on the board design, connected in
multiple different ways to the SerDes lanes.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/20260518142026.3098496-4-ioana.ciornei@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The PCIe SSC configuration for the RK3588 and RK3576 SoCs required
additional tuning which is missing. When adding these same SSC
configurations for both of these two SoCs, as well as upcoming
platforms, it's obvious the SSC setup code was largely duplicated
across the platform-specific configuration functions. This becomes
harder to maintain as more platforms are added.
So extract the common SSC logic into a shared helper function,
rk_combphy_common_cfg_ssc(). This cleans up the per-platform drivers
and centralizes the standard configuration as possible.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://patch.msgid.link/1777251433-110466-1-git-send-email-shawn.lin@rock-chips.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Keep the USB pipe clock working when the phy is in DP-only mode, because
the dwc controller still needs it for USB 2.0 over the same Type-C port.
Tested with the BenQ RD280UA monitor which has a downstream-facing port
for data passthrough that's manually switchable between USB 2 and 3,
corresponding to 4-lane and 2-lane DP respectively.
Note: the suspend/resume callbacks were already gating the enable/disable
of this clock only on init_count and not usb_init_count!
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Val Packett <val@packett.cool>
Link: https://patch.msgid.link/20260304190827.176988-1-val@packett.cool
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Instead of kzalloc and kcalloc, we can use a flex array to reduce to a
single allocation.
Also added __counted_by() for extra possible analysis.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://patch.msgid.link/20260304043420.14151-1-rosenp@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Introduce support for EcoNet PCIe PHY controllers found in EN751221
and EN7528 SoCs, these SoCs are not identical but are similar, each
having one Gen1 port, and one Gen1/Gen2 port.
Co-developed-by: Ahmed Naseef <naseefkm@gmail.com>
Signed-off-by: Ahmed Naseef <naseefkm@gmail.com>
[cjd@cjdns.fr: add EN751221 support and refactor for clarity]
Signed-off-by: Caleb James DeLisle <cjd@cjdns.fr>
Link: https://patch.msgid.link/20260425173642.406089-3-cjd@cjdns.fr
Signed-off-by: Vinod Koul <vkoul@kernel.org>
EN751221 and EN7528 SoCs have two PCIe slots, and each one has a PHY
which behaves slightly differently because one slot is Gen1/Gen2 while
the other is Gen1 only.
Signed-off-by: Caleb James DeLisle <cjd@cjdns.fr>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://patch.msgid.link/20260425173642.406089-2-cjd@cjdns.fr
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The RK3528 has a single USB2PHY with a otg and host port.
Add support for the RK3528 variant of USB2PHY.
PHY tuning for RK3528:
- Turn off differential receiver in suspend mode to save power
consumption.
- Set HS eye-height to 400mV instead of default 450mV.
- Choose the Tx fs/ls data as linestate from TX driver for otg port
which uses dwc3 controller to improve fs/ls devices compatibility with
long cables.
Undocumented magic-values are based on the linux-stan-6.1-rkr5 tag of
the vendor-kernel.
Signed-off-by: Jianwei Zheng <jianwei.zheng@rock-chips.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20260505170410.3265305-6-heiko@sntech.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The 480m clk is controlled using regs in the PHY address space and not
in the USB GRF address space on e.g. RK3528 and RK3506.
Add a clkout_ctl_phy usb2phy_reg to handle enable/disable of the 480m
clk on these SoCs.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20260505170410.3265305-5-heiko@sntech.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The embedded USB2 PHY on RK3528 is very similar to the one in RK3568,
the main difference being that it only uses two clocks instead of three.
Add compatible to support the USB2 PHY in RK3528.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20260505170410.3265305-4-heiko@sntech.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The logic to decide if usbgrf or grf should be used is more complex than
it needs to be. For RK3568, RV1108 and soon RK3528 we can assign the
rockchip,usbgrf regmap directly to grf instead of doing a usbgrf and grf
dance.
Simplify the code to only use the grf regmap and handle the logic of
what regmap should be used in driver probe instead.
The only expected change from this is that RK3528 can be supported
because of an addition of a of_property_present() check.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20260505170410.3265305-3-heiko@sntech.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Typically these Rockchip USB2 PHYs are fully contained within a single
GRF. However, for RK3568 and RV1108 regs to control the USB2 PHY is
located in a different GRF compared to the base address.
Update this binding to require rockchip,usbgrf for RK3568 and RV1108 to
properly reflect that the USB GRF is required to control the USB2 PHYs
on these variants. Also disable use of rockchip,usbgrf for variants
where it is not required.
This should not introduce any breakage as the affected usb2phy nodes for
RK3568 and RV1108 were added together with a rockchip,usbgrf phandle in
their initial commit.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20260505170410.3265305-2-heiko@sntech.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This file does not use the symbols from the legacy
<linux/gpio.h> header, so let's drop it.
Reviewed-by: Josua Mayer <josua@solid-run.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20260513220336.369628-7-andriy.shevchenko@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The code like
int foo = X;
...
if (bar)
foo = Y;
is prone to subtle mistakes and hence harder to maintain as the foo value
may be changed inadvertently while code in '...' grown in lines. On top
it's harder to navigate to understand the possible values of foo when branch
is not taken (requires to look somewhere else in the code, far from the piece
at hand).
Besides that in case of taken branch the foo will be rewritten, which is
not a problem per se, just an unneeded operation.
Decouple assignment and definition to use if-else to address the inconveniences
described above.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20260513220336.369628-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Instead of checking for the specific error codes (that can be considered
a layering violation to some extent) check for the property existence first
and then either parse it, or apply a default value.
With that, return an error when parsing of the existing property fails.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20260513220336.369628-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There is no code that uses ID table directly, except the
struct device_driver at the end of the file. Hence, move
table closer to its user. It's always possible to access
them via a pointer.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20260513220336.369628-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Use the generic firmware node interface for retrieving
device match data instead of the OF-specific one.
While at it, drop unneeded argument to devm_phy_create() which
extracts device node from the given device by default.
Reviewed-by: Josua Mayer <josua@solid-run.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20260513220336.369628-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Every platform driver can be forced to match a device that doesn't
match its list of device IDs because of device_match_driver_override()
so platform drivers that rely on the existence of a device's driver
data need to verify its presence.
Accordingly, add requisite match and driver data checks against NULL
to the driver where they are missing.
Fixes: a4a86d273f ("phy: phy-can-transceiver: Add support for generic CAN transceiver driver")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20260513220336.369628-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for 25GBASE-R in the Lynx 28G SerDes PHY driver. This will
be used by the dpaa2-mac consumer on LX2160A with:
- phy_validate(phy, PHY_MODE_ETHERNET, PHY_INTERFACE_MODE_25GBASER) to
detect support.
- phy_set_mode_ext(phy, PHY_MODE_ETHERNET, PHY_INTERFACE_MODE_25GBASER)
to reconfigure the lane for this protocol.
The intended use case for dynamic protocol switching to 25GBase-R is
with SFP28 modules, and protocol switching is triggered by the SFP
module insertion. There also exists a 25GBase-KR use case, where the
protocol switching is covered by IEEE 802.3 clause 73 auto-negotiation.
However, that is not handled here; it merely needs the support added
here as basic ground work.
The lane frequency for 25GbE is sourced from a clock net frequency of
12.890625 GHz, as produced by PLLF or PLLS, further multiplied by the
lane by 2. The clock net frequencies produced by the PLLs are treated as
read-only by the driver, so the absence of a PLL provisioned for the
right clock net frequency implies absence of 25GbE support, even though
a lane might have the appropriate protocol converter for it.
In terms of implementation, the change consists of:
- determining at probe time if any PLL was preconfigured for the
required clock net frequency for 25GbE
- adding the default lane parameters for reconfiguring a lane to 25GbE
irrespective of the original protocol
- allowing this operating mode only on supported lanes, i.e. all lanes
of LX2162A SerDes #1, and LX2160A SerDes lanes 0-1, 4-7.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Josua Mayer <josua@solid-run.com>
Link: https://patch.msgid.link/20260511150023.1903577-6-vladimir.oltean@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add driver support for probing on the new, per-instance and per-SoC
bindings, which provide the main benefit that they allow rejecting
unsupported protocols per lane (10GbE on SerDes 2 lanes 0-5), but they
also allow avoiding the creation of PHYs for lanes that don't exist
(LX2162A lanes 0-3).
For old device trees with just "fsl,lynx-28g", the only things that
change are:
- a probe time warning/encouragement to update the device tree. This is
warranted by the fact that using "fsl,lynx-28g" may already provide
incorrect behaviour (undetected absent 10GbE support on LX2160A
SerDes 2 lanes 0-5). But we retain bug compatibility nonetheless.
- the feature set is frozen in time (e.g. no 25GbE). Since we cannot
guarantee that this protocol will work on a lane, just err on the safe
side and don't offer it (and require a device tree update to get it).
In terms of code, the lynx_28g_supports_lane_mode() function prototype
changes. It was a SerDes-global function and now becomes per lane, to
reflect the specific capabilities each instance may have. The
implementation goes through priv->info->lane_supports_mode().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Josua Mayer <josua@solid-run.com>
Link: https://patch.msgid.link/20260511150023.1903577-5-vladimir.oltean@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver will gain support for variants in an upcoming change, and
will use of_device_get_match_data() to deduce the running variant from
the compatible string.
Currently, the driver expects the schema at phy/fsl,lynx-28g.yaml, and
OF-based consumers, but doesn't enforce this. And it is possible for
user space to force-bind the driver to a device without OF node using
the driver_override sysfs.
To avoid future surprise crashes for an unsupported configuration,
explicitly test for the presence of an OF node and fail probing if
found.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Josua Mayer <josua@solid-run.com>
Link: https://patch.msgid.link/20260511150023.1903577-4-vladimir.oltean@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The SerDes 1 of LX2162A has fewer lanes than all other instances, and
strangely, their indices are not 0-3, but 4-7.
This is a best-effort constraint, since we can only impose it when using
per-SoC compatible string and per-lane OF nodes.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Tested-by: Josua Mayer <josua@solid-run.com>
Link: https://patch.msgid.link/20260511150023.1903577-3-vladimir.oltean@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The 28G Lynx SerDes is instantiated 3 times in the NXP LX2160A SoC and
twice in the NXP LX2162A. All these instances share the same register
map, but the number of lanes and the protocols supported by each lane
differs in a way that isn't detectable by the programming model.
For example, not all lanes of all SerDes block instantiations support
25GbE.
So, using a generic "fsl,lynx-28g" compatible string and expecting all
SerDes instantiations to use it was a mistake that needs to be fixed.
The option chosen is to encode the SoC and the SerDes instance in the
compatible string, with everything else being the responsibility of the
driver to derive.
An alternative considered but dismissed was to add sufficient device
tree properties to describe the per-lane differences (implying:
supported protocols), as well as the different lane count.
Any decision made for the 28G Lynx should be consistent with the
decisions taken for the yet-to-be-introduced 10G Lynx SerDes (older
generation for older SoCs), because of how similar they are.
I've seen the alternative at play in this unmerged patch set for the 10G
Lynx here, and I didn't like it:
https://lore.kernel.org/linux-phy/20230413160607.4128315-3-sean.anderson@seco.com/
This is because there, we have a higher degree of variability in the
PCCR register values that need to be written per protocol. This makes
that approach more drawn-out and more prone to errors, compared to the
compatible strings which are more succinct and obviously correct.
NXP SoC reference manuals clearly document the SerDes instantiations as
not identical, and refers to them as such (SerDes 1, 2, etc).
The per-SoC compatible string is prepended to the "fsl,lynx-28g" generic
compatible, which is left there for compatibility with old kernels. An
exception would be LX2160A SerDes #3, which at the time of writing is
not described in fsl-lx2160a.dtsi. As "fsl,lx2160a-serdes3" implies it
is a 28G Lynx SerDes, it makes "fsl,lynx-28g" redundant so we don't
accept it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Tested-by: Josua Mayer <josua@solid-run.com>
Link: https://patch.msgid.link/20260511150023.1903577-2-vladimir.oltean@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This driver uses multiple regmaps, which will causes name conflicts
in debugfs like:
debugfs: '5f1a0000.phy' already exists in 'regmap'
Fix this by using a dedicated regmap config for each resource, each
having a dedicated regmap name.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260211144949.1128122-1-alexander.stein@ew.tq-group.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There's nothing special here to prevent compilation on non ARM hosts.
Matches every other st phy driver.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://patch.msgid.link/20260306222457.8400-2-rosenp@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
EyeQ5 embeds a system-controller called OLB. It features many unrelated
registers, and some of those are registers used to configure the
integration of the RGMII/SGMII Cadence PHY used by MACB/GEM instances.
Wrap in a neat generic PHY provider, exposing two PHYs with standard
phy_init() / phy_set_mode() / phy_power_on() operations.
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/20260309-macb-phy-v9-1-5afd87d9db43@bootlin.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fix a malformed MODULE_AUTHOR macro in the RZ/G3E USB3.0 PHY driver where
the author's name and opening angle bracket were missing, leaving only the
email address with a stray closing >. Correct it to the standard Name
<email> format.
Reported-by: Pavel Machek <pavel@nabladev.com>
Closes: https://lore.kernel.org/all/abp4KprlYyU+jMPu@duo.ucw.cz/
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://patch.msgid.link/20260319063211.5056-1-biju.das.jz@bp.renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
On Layerscape, some Lynx SerDes consumers go through the PHY framework
(we call these 'managed' for the sake of this discussion; they are some
Ethernet lanes), and some consumers don't go through the PHY framework
(we call these 'unmanaged'; they are some unconverted Ethernet lanes,
plus all SATA and PCIe controllers).
A lane is initially unmanaged, and becomes managed when phy_init() is
called on it. Similarly, it becomes unmanaged again when phy_exit() is
called.
Managed lanes are supposed to have power management through
phy_power_on() and phy_power_off().
The lynx-28g SerDes driver, when it probes, probes on all lanes, but
needs to be careful to keep the unmanaged lanes powered on, because
those might be in use by consumers unaware that they need to call
phy_init() and phy_power_on(). This also applies after phy_exit() is
called - no guarantee is made about how the port may be used
afterwards - may be DPDK, may be something else which is unaware of
the PHY framework.
Given this state table:
State | Consumer calls phy_exit()? | Provider implements phy_exit()?
-------+----------------------------+--------------------------------
(a) | no | no
(b) | no | yes
(c) | yes | no
(d) | yes | yes
we are currently in state (a). This has the problem that when the
consumer fails to probe with -EPROBE_DEFER or is otherwise unbound,
the phy->init_count remains elevated and the lane never returns to the
unmanaged state (temporarily or not) as it should. Furthermore, the
second and subsequent phy_init() consumer calls are never passed on to
the provider driver.
We solve the above problem by implementing phy_exit() in the consumer,
and that moves us to state (c). But this creates the problem that a
balanced set of phy_init() and phy_exit() calls from the consumer will
effectively result in multiple lynx_28g_init() calls as seen by the
SerDes and nothing else - as the optional phy_ops :: exit() is not
implemented. But that actually doesn't work - the 28G Lynx SerDes can't
power down a lane which is already powered down; that call sequence
would time out and fail.
So actually we want to be in state (d), where both the provider and the
consumer implement phy_exit(). But we can only do that safely through
intermediary state (b), where the provider implements it first. This
effectively behaves just like (a), except it offers a safe migration
path for the consumer to call phy_exit() as mandated by the Generic PHY
API.
Extra development notes: ignoring the lynx_28g_power_on() error in
lynx_28g_exit() is a deliberate decision. The consumer can't deal with a
teardown path that is not error-free. Ignoring the error is not silent:
lynx_28g_power_on() -> lynx_28g_lane_reset() will print on failure.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20260321011451.1557091-4-vladimir.oltean@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The current procedure for power_off() and power_on() is the same as the
one used for major lane reconfiguration, aka halting. But this is
incorrect.
One would expect that a powered off lane causes the CDR (clock and data
recovery) loop of the link partner to lose lock onto its RX stream
(which suggests there are no longer any bit transitions => the channel
is inactive). However, it can be observed that this does not take place
(the CDR lock is still there), which means that a halted lane is not
powered off.
Implement the procedure mentioned in the block guide for powering down
a lane, and then back on. This means:
- lynx_28g_power_off() currently emits a HLT_REQ and waits for it to
clear. Rename it to lynx_28g_lane_halt() and keep using it for
lynx_28g_set_mode().
- lynx_28g_power_on() currently emits a RST_REQ and waits for it to
clear. This is the reset procedure - rename it to
lynx_28g_lane_reset(), and keep using it for lynx_28g_set_mode().
The "real" lynx_28g_power_off() should emit a STP_REQ and wait for it to
clear. And the "real" lynx_28g_power_on() should clear the DIS bit and
then perform a lane reset. Hook these methods to the phy_ops ::
power_off() and power_on() instead.
As opposed to lynx_28g_power_off() which is also directly hooked to the
PHY API, lynx_28g_lane_halt() isn't; just to lynx_28g_set_mode(), and
the call is being made in a state where we haven't yet made any change
to the lane. So it does make some limited amount of sense to code this
up such that if it fails, we make an attempt to reset the lane anyway
and let the consumer know that phy_set_mode_ext() failed.
Sort the field definitions in LNaTRSTCTL and LNaRRSTCTL in descending
order, and add new definitions for STP_REQ and DIS, previously unused.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20260321011451.1557091-3-vladimir.oltean@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There are various circumstances in which a lane halt, or a lane reset,
will fail to complete. If this happens, it will hang the kernel, which
only implements a busy loop with no timeout.
The circumstances in which this will happen are all bugs in nature:
- if we try to power off a powered off lane
- if we try to power off a lane that uses a PLL locked onto the wrong
refclk frequency (wrong RCW, but SoC boots anyway)
Actually, unbounded loops in the kernel are a bad practice, so let's use
read_poll_timeout() with a custom function that reads both LNaTRSTCTL
(lane transmit control register) and LNaRRSTCTL (lane receive control
register) and returns true when the request is done in both directions.
The HLT_REQ bit has to clear, whereas the RST_DONE bit has to get set.
Any time such an error happens, it is catastrophic and there is no point
in trying to propagate it to our callers:
- if lynx_28g_set_mode() -> lynx_28g_power_on() times out, we have
already reconfigured the lane, but returning an error would tell the
caller that we didn't
- if lynx_28g_power_off() times out, again not much for the consumer to
do to help get out of this situation - the phy_power_off() call is
probably made from a context that the consumer can't cancel, or it is
making it to return to a known state from a previous failure.
So just print an error if timeouts happen and let the driver control
flow continue. The entire point is just to not let the kernel freeze.
Suggested-by: Josua Mayer <josua@solid-run.com>
Link: https://lore.kernel.org/lkml/d0c8bbf8-a0c5-469f-a148-de2235948c0f@solid-run.com/
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260321011451.1557091-2-vladimir.oltean@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
A repeater is not required for the PHY to function. On systems with
multiple PHY instances connected to a multi-port controller, some PHYs
may be unconnected. All PHYs must still probe successfully even without
attached repeaters, otherwise the controller probe fails.
So make it optional.
Signed-off-by: Wesley Cheng <wesley.cheng@oss.qualcomm.com>
[abel.vesa@oss.qualcomm.com: commit re-worded to reflect actual reason]
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://patch.msgid.link/20260302-phy-qcom-m31-eusb2-make-repeater-optional-v2-1-dbf714c72056@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The initial sa8775p eDP PHY binding contribution missed adding support for
voting on the eDP reference clock. This went unnoticed because the UFS PHY
driver happened to enable the same clock.
After commit 77d2fa54a9 ("scsi: ufs: qcom : Refactor phy_power_on/off
calls"), the eDP reference clock is no longer kept enabled, which results
in the following PHY power-on failure:
phy phy-aec2a00.phy.10: phy poweron failed --> -110
To fix this, explicit voting for the eDP reference clock is required.
This patch adds the eDP reference clock for sa8775p eDP PHY and updates
the corresponding example node.
Signed-off-by: Ritesh Kumar <quic_riteshk@quicinc.com>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Acked-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20260128114853.2543416-2-quic_riteshk@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Commit 81791c45c8 ("phy: qcom: qmp-usbc: Add QCS615 USB/DP PHY config
and DP mode support") chose to name QCS615 DP PHY variables/functions
with qmp_v2 prefix, by assuming that QMP PHY registers are versioned
as a whole. However, the reality is that the registers are versioned
in sub-modules like QSERDES COM and QSERDES TXRX respectively, e.g.
QCS615 DP PHY has registers of QSERDES COM v2 and QSERDES TXRX v3.
Thus it may cause confusion that qmp_v2_xxx table and functions access
QSERDES TXRX v3 registers.
Rename QCS615 DP PHY variables and functions to be prefixed by qcs615
instead of qmp_v2. This better aligns with how the driver names USB3 PHY
variables for QCM2290 etc.
Signed-off-by: Shawn Guo <shengchao.guo@oss.qualcomm.com>
Link: https://patch.msgid.link/20260314051325.198137-5-shengchao.guo@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The register definitions in header qserdes-txrx-v2 and qserdes-txrx-v3
are actually identical. Considering that QSERDES TX/RX v2 is already
defined by header qserdes-txrx, qserdes-txrx-v2 is really just
a duplication of qserdes-txrx-v3 for QSERDES TX/RX v3. Switch
qcom-qmp-usbc driver to use v3 registers.
Signed-off-by: Shawn Guo <shengchao.guo@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://patch.msgid.link/20260314051325.198137-4-shengchao.guo@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
As the code comments in the headers say, both qserdes-com and
qserdes-com-v2 define QSERDES COM registers for QMP V2 PHY. Switch
phy-qcom-qmp drivers to use register definitions in qserdes-com-v2
to make the QSERDES COM version explicit.
Signed-off-by: Shawn Guo <shengchao.guo@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://patch.msgid.link/20260314051325.198137-3-shengchao.guo@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
A few registers that could be used by phy-qcom-qmp drivers are missing
from qserdes-com-v2 header. Add them.
Signed-off-by: Shawn Guo <shengchao.guo@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://patch.msgid.link/20260314051325.198137-2-shengchao.guo@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
kconfiglint reports:
K006: config PHY_TEGRA_XUSB selects USB_CONN_GPIO which depends on
GPIOLIB, but PHY_TEGRA_XUSB does not depend on GPIOLIB
K002: config PHY_TEGRA_XUSB selects visible symbol USB_CONN_GPIO
which has dependencies
USB_CONN_GPIO was introduced in commit 4602f3bff2 ("usb: common: add USB
GPIO based connection detection driver") with a hard dependency on GPIOLIB,
since it needs GPIO pins to detect USB cable connection state.
Commit f67213cee2 ("phy: tegra: xusb: Add usb-role-switch support") added
`select USB_CONN_GPIO` to PHY_TEGRA_XUSB to support USB role switching via
GPIO-based detection. At that time, PHY_TEGRA_XUSB depended only on
`ARCH_TEGRA`, and both the ARM32 and ARM64 ARCH_TEGRA Kconfig definitions
select GPIOLIB, so the missing explicit GPIOLIB guard was not a functional
problem — GPIOLIB is always available when ARCH_TEGRA is enabled.
Later, commit 0d5c9bc7c6 ("phy: tegra: Select USB_COMMON for
usb_get_maximum_speed()") added `depends on USB_SUPPORT` but still did not
address the GPIOLIB gap.
The select can force USB_CONN_GPIO on without its GPIOLIB dependency being
satisfied if the Kconfig dependencies were ever restructured. Make the
select conditional with `select USB_CONN_GPIO if GPIOLIB` to make the
dependency explicit. This mirrors how other drivers handle optional
GPIO-dependent selects throughout the kernel.
Assisted-by: Claude:claude-opus-4-6 kconfiglint
Signed-off-by: Sasha Levin <sashal@kernel.org>
Link: https://patch.msgid.link/20260426000309.54959-1-sashal@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Document the compatible for the USB QMP PHY found on the Qualcomm Eliza
SoC.
It is fully compatible with the one found on Qualcomm SM8650, so add it
with the SM8650 as fallback.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Link: https://patch.msgid.link/20260504-eliza-bindings-qmp-phy-v2-1-849c4de8d75f@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The Synopsys eUSB2 PHY found on the Eliza SoC is fully compatible with the
one found the SM8550.
So document it by adding the compatible to the list that has the SM8550
one as fallback.
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Link: https://patch.msgid.link/20260504-eliza-bindings-phy-eusb2-v2-1-fa3a1fd65ab1@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
