The first USB port features a Type-C connector with dual data role
and dual power role capabilities. Add the Type-C device node and
enable the corresponding USB controller and phy node.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Update the SIUL2 pinctrl node to describe the additional register
ranges and DT properties used by the updated SIUL2 driver.
Besides the MSCR and IMCR ranges used for pinmux and pin
configuration, the SIUL2 block also provides PGPDO and
PGPDI registers for GPIO output and input operations,
as well as an EIRQ register window for external interrupt configuration.
The driver supports both legacy pinctrl-only DTs and
extended DTs with GPIO and IRQ.
Reflect these resources in the SIUL2 pinctrl node by adding:
- the PGPDO and PGPDI register ranges
- the EIRQ register range
- gpio-controller, #gpio-cells and gpio-ranges
- interrupt-controller, #interrupt-cells and interrupts
Keep the hardware description aligned with the updated SIUL2
driver, where pinctrl, GPIO data access and the EIRQ register
block are described under the same device node.
Signed-off-by: Khristine Andreea Barbulescu <khristineandreea.barbulescu@oss.nxp.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add device tree support for the Variscite Sonata carrier board with the
DART-MX8M-PLUS system on module.
The Sonata board includes
- uSD Card support
- USB ports and OTG
- Additional Gigabit Ethernet interface
- Uart, SPI and I2C interfaces
- HDMI support
- GPIO Expanders
- RTC module
- TPM module
- CAN peripherals
Link: https://variscite.com/carrier-boards/sonata-board/
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add device tree support for the Variscite DART-MX8MP system on module.
This SOM is designed to be used with various carrier boards.
The module includes:
- NXP i.MX8M Plus MPU processor
- Up to 8GB of LPDDR4 memory
- Up to 128GB of eMMC storage memory
- Integrated 10/100/1000 Mbps Ethernet Transceiver
- Codec audio WM8904
- WIFI6 dual-band 802.11ax/ac/a/b/g/n with optional 802.15.4 and Bluetooth
Only SOM-specific peripherals are enabled by default. Carrier board
specific interfaces are left disabled to be enabled in the respective
carrier board device trees.
Link: https://variscite.com/system-on-module-som/i-mx-8/i-mx-8m-plus/dart-mx8m-plus/
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add DT compatible strings for Variscite DART-MX8MP SoM and Variscite
development carrier Board.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Move the power supply properties from the PCIe controller nodes to the
Root Port child nodes to support the new PCI pwrctrl framework.
Since i.MX95 is the new platform that under development phase, it should
be fine to simply move the power supply properties.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add the power supply properties to the Root Port child nodes to support
the new PCI pwrctrl framework.
Legacy power supply properties are retained for backward compatibility
with existing kernels. New device trees should specify power supplies at
the Root Port level to utilize the pwrctrl framework.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add the power supply properties to the Root Port child nodes to support
the new PCI pwrctrl framework.
Legacy power supply properties are retained for backward compatibility
with existing kernels. New device trees should specify power supplies at
the Root Port level to utilize the pwrctrl framework.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add the power supply properties to the Root Port child nodes to support
the new PCI pwrctrl framework.
Legacy power supply properties are retained for backward compatibility
with existing kernels. New device trees should specify power supplies at
the Root Port level to utilize the pwrctrl framework.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add the power supply property to the Root Port child node to support the
new PCI pwrctrl framework.
Legacy power supply property is retained for backward compatibility with
existing kernels. New device trees should specify power supply at the
Root Port level to utilize the pwrctrl framework.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
On the DART-MX95 platform, INL1/DMICDAT1 is used as the DMIC data line.
Add the wlf,in1l-as-dmicdat1 property to reflect this configuration.
This enables the internal MUX to switch between the ADC and DMIC as the
capture input.
Co-developed-by: Alexander Herfurtner <alexander.h@variscite.com>
Signed-off-by: Alexander Herfurtner <alexander.h@variscite.com>
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Enable the NETC and NETCMIX block control nodes on the DART-MX95 SoM.
These block control nodes are required to enable and use the NETC
Ethernet ports.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Since describing the PCIe PERST# property under Host Bridge node is now
deprecated, it is recommended to add it to the Root Port node, so creating
the root port node and add the reset-gpios property in root port.
Move the regulator to root port nodes as well, because that the PCI pwrctrl
framework had been integrated into pci-imx6 driver.
The backward compatibility is not a concern since i.MX94 is a newly
introduced platform that is still under active development.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Since describing the PCIe PERST# property under Host Bridge node is now
deprecated, it is recommended to add it to the Root Port node, so creating
the root port node and pave the path to add the reset-gpios and so on
properties in root port later.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Enable the MU2 (Message Unit 2) node on the i.MX8MP Audio Board v2.
MU2 is required for inter-processor communication between the
application CPU and the HiFi4 DSP, allowing DSP firmware to exchange
control and status messages with the Linux host.
Without this change, the DSP driver cannot establish the message
channel and DSP audio processing is non-functional.
Fixes: bf68c18150 ("arm64: dts: imx8mp-ab2: add support for NXP i.MX8MP audio board (version 2)")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add alias for lpuart5 so the UART gets a stable line number.
Without this alias, the lpuart driver fails:
fsl-lpuart 42590000.serial: failed to get alias id, errno -19
This prevents the Bluetooth controller connected to this UART from
working.
Fixes: 104a391bb6 ("arm64: dts: freescale: imx95-toradex-smarc: Enable bluetooth on lpuart5")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
The start address of the DRAM area is 0x80000000. The minimal size of the
DDR on the SoM is 1 GiB.
Fixes: 2b52fd6035 ("arm64: dts: Add support for Kontron i.MX93 OSM-S SoM and BL carrier board")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
This adds an overlay for the supported LVDS display AUO G133HAN01.
Configure the video PLL frequency to exactly match typical pixel clock of
141.200 MHz.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
This adds overlays for the supported LVDS display tianma tm070jvhg33
for both LVDS channels.
The display timings have to be specified explicitly. Using the typical
pixel clock, the LDB clock can not be configured as the 7-fold of that.
By setting pixel clock to 74.25 MHz, LDB can be configured to exactly
519.75 MHz.
Signed-off-by: Paul Gerber <paul.gerber@tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
This adds support for TQMa8MPQS module on MB-SMARC-2 board.
Signed-off-by: Paul Gerber <paul.gerber@tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
TQMa8MPxS is a SOM family using NXP i.MX8MP CPU family.
MB-SMARC-2 is an evaluation mainbord for this SOM
The SOM needs a mainboard, therefore we provide two compatibles here:
"tq,imx8mp-<SOM>" for the module and
"tq,imx8mp-<SOM>-<SBC>"
Signed-off-by: Paul Gerber <paul.gerber@tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add the GPIO pinctrl state and GPIO descriptors required for I2C1 bus
recovery on the VAR-SOM-MX8M-PLUS.
This allows the I2C controller to recover the bus if SDA or SCL are held
low by a device.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add support for the second Ethernet interface available on the Symphony
carrier board.
Enable the FEC controller, add the MaxLinear MXL86110 Gigabit Ethernet
PHY on the MDIO bus, describe its reset and power configuration, and add
the required RGMII pinctrl settings.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Enable the FlexCAN2 controller on the Symphony carrier board and add the
corresponding pinctrl configuration.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Enable PWM1 on the Symphony carrier board and add the corresponding
pinctrl configuration.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Keep the RGB_SEL line driven low on the Symphony carrier board.
This avoids leaving the line floating and ensures the board remains in
the expected display configuration.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Enable the ECSPI2 bus on the Symphony carrier board and add the pinctrl
configuration for the SPI signals and chip select GPIO.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add the FT5206 capacitive touchscreen controller on the Symphony carrier
board.
Describe the interrupt pin and touchscreen geometry.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Enable the HDMI display pipeline and HDMI audio support on the Symphony
carrier board.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add the PCIe reference clock and enable the PCIe controller and PHY on
the Symphony carrier board.
Describe the PERST# reset GPIO and configure the PHY to use an external
reference clock input.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Keep the RGB_SEL line driven low on the Symphony carrier board.
This avoids leaving the line floating and ensures the board remains in
the expected display configuration.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Mark the Symphony carrier board GPIO keys and capacitive touchscreen as
wakeup sources.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Configure HDMI DDC SCL/SDA pins to support reading EDID.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Fixes: 95d7d7d2ad ("arm64: dts: imx8mp-frdm: add sd, ethernet, wifi, usb and hdmi support")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add LVDS Display Bridge(LDB) child node to mediamix blk-ctrl node
so that video could be output through a LVDS interface.
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
i.MX93 SoC mediamix blk-ctrl contains one LDB_CTRL register and one LVDS
register which control video output through a LVDS interface. Allow the
LVDS Display Bridge(LDB) child node and add the child node to example.
i.MX93 LDB child node(bridge@20) is an addressable node, while i.MX93
Parallel Display Format Configuration(PDFC) child node(dpi-bridge) is a
non-addressable node. Mixing the addressable and non-addressable child
nodes is allowed according to discussion [1].
Link: https://lore.kernel.org/all/n6akxiayi3g6gxcqhreb4iaohmeokoalnqup6h5r2fwdt4zijt@u2wyps55ayqm/ [1]
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Enable UART1 and UART4 on the Symphony carrier board and add the
corresponding pinctrl configurations.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add the DS1337 RTC on the Symphony carrier board and disable the internal
SNVS RTC.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add the ST33KTPM2XI2C TPM device on the Symphony carrier board.
Enable the I2C4 bus, add the PCAL6408 GPIO expander used by the TPM and
describe the TPM reset line.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Enable the USB controllers on the Symphony carrier board.
Add the PTN5150 Type-C controller for USB role switching, enable the USB3
PHYs and controllers, configure the I2C bus used by the Type-C
controller, and set the first USB port in OTG mode and the second port
in host mode.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add the Back, Home and Menu keys connected through the GPIO expander on
the Symphony carrier board.
Also enable the SNVS power key.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Fix the PCIe outbound memory ranges for both pcie1 controllers on i.MX943.
The memory window size was incorrectly set to 256MB during initial
bring-up, but the hardware supports up to 4GB of outbound address space
per controller.
Additionally, the ECAM region cannot be mapped as I/O space. Use a
memory-mapped region for I/O space instead, and relocate the 1MB I/O
region to immediately follow the memory region at offset 0xf0000000
within each window.
Update the outbound address space layout per controller as follows:
- 3.5GB 64-bit prefetchable memory
- 256MB 32-bit non-prefetchable memory
- 1MB I/O
Fixes: fa6067fd8e ("arm64: dts: imx943: Add pcie1 and pcie1-ep supports")
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Fix the PCIe outbound memory ranges for both pcie0 controllers on i.MX94.
The memory window size was incorrectly set to 256MB during initial
bring-up, but the hardware supports up to 4GB of outbound address space
per controller.
Additionally, the ECAM region cannot be mapped as I/O space. Use a
memory-mapped region for I/O space instead, and relocate the 1MB I/O
region to immediately follow the memory region at offset 0xf0000000
within each window.
Update the outbound address space layout per controller as follows:
- 3.5GB 64-bit prefetchable memory
- 256MB 32-bit non-prefetchable memory
- 1MB I/O
Fixes: 8cd439f177 ("arm64: dts: imx94: Add pcie0 and pcie0-ep supports")
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
The board integrates an on-board mux to route shared signals to either
CAN2 or PDM (MICFIL). The mux is controlled by a GPIO.
Add a pinctrl-based multiplexer node to describe this routing and ensure
proper probe ordering of the dependent devices.
Previously, MICFIL operation implicitly depended on the default level of
PCA6416 GPIO3. After adding the pinctrl-multiplexer, make the dependency
explicit.
Reviewed-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
The i.MX93 TMU node compatible need to be updated to apply the SoC
specific configuration and TMU errata workaround.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
device removal, along with documentation fixes and minor AMD driver
cleanups.
-----BEGIN PGP SIGNATURE-----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=V3cD
-----END PGP SIGNATURE-----
Merge tag 'ntb-7.2' of https://github.com/jonmason/ntb
Pull NTB updates from Jon Mason:
"An EPF bug fix to prevent an invalid unmap during device removal,
along with documentation fixes and minor AMD driver cleanups"
* tag 'ntb-7.2' of https://github.com/jonmason/ntb:
ntb: amd: Use named initializer for pci_device_id::driver_data
NTB: fix kernel-doc warnings in ntb.h
NTB: epf: Avoid pci_iounmap() with offset when PEER_SPAD and CONFIG share BAR
ntb_hw_amd: Fix incorrect debug message in link disable path
- Updates to Synaptics RMI4 driver to fix potential OOB accesses in
F30 and F3A keymap handling
- A workaround in Synaptics RMI4 to tolerate buggy firmware on some
touchpads (e.g. ThinkPad T14 Gen 1) that report incomplete register
descriptor structures, preventing probe failures
- A revert of an incorrect register descriptor address calculation in
Synaptics RMI4 driver
- A fix for a regression in HP GSC PS/2 (gscps2) driver where the
receive buffer write index was not advanced, leaving keyboard and
mouse unusable.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQST2eWILY88ieB2DOtAj56VGEWXnAUCakCsxwAKCRBAj56VGEWX
nCICAQDSgfrAi+4SqTb92EjtdQO+ypluS42mKO75LTitJcS8dAEA1iKmdss8mGww
c4ai4W+UFxori7IqgkoQ7LfaPTOWlA0=
=QP4c
-----END PGP SIGNATURE-----
Merge tag 'input-for-v7.2-rc0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull more input updates from Dmitry Torokhov:
- Updates to Synaptics RMI4 driver to fix potential OOB accesses in F30
and F3A keymap handling
- A workaround in Synaptics RMI4 to tolerate buggy firmware on some
touchpads (e.g. ThinkPad T14 Gen 1) that report incomplete register
descriptor structures, preventing probe failures
- A revert of an incorrect register descriptor address calculation in
Synaptics RMI4 driver
- A fix for a regression in HP GSC PS/2 (gscps2) driver where the
receive buffer write index was not advanced, leaving keyboard and
mouse unusable.
* tag 'input-for-v7.2-rc0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: gscps2 - advance receive buffer write index
Input: rmi4 - tolerate short register descriptor structure
Revert "Input: rmi4 - fix register descriptor address calculation"
Input: synaptics-rmi4 - bound the F30 keymap to the GPIO/LED count
Input: synaptics-rmi4 - bound the F3A keymap to the GPIO count
