The 'eee-broken-1000t' flag disables Energy-Efficient Ethernet (EEE) on 1G
links as a workaround for PTP sync issues on older i.MX6 platforms.
Remove it since the i.MX93 have not such issue.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add i.MX91 11x11 EVK board support.
- Enable ADC1.
- Enable lpuart1 and lpuart5.
- Enable network eqos and fec.
- Enable I2C bus and children nodes under I2C bus.
- Enable USB and related nodes.
- Enable uSDHC1 and uSDHC2.
- Enable Watchdog3.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Pengfei Li <pengfei.li_1@nxp.com>
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX 91 family features an Arm Cortex-A55 running at up to 1.4GHz,
support for modern LPDDR4 memory to enable platform longevity, along
with a rich set of peripherals targeting medical, industrial and
consumer IoT market segments.
The mainly difference between i.MX91 and i.MX93 is as follows:
- i.MX91 removed some clocks and modified the names of some clocks.
- i.MX91 only has one A core.
- i.MX91 has different pinmux.
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The design of i.MX91 platform is very similar to i.MX93 and only
some small differences.
If the imx91.dtsi include the imx93.dtsi, each add to imx93.dtsi
requires an remove in imx91.dtsi for this unique to i.MX93, e.g. NPU.
The i.MX91 isn't the i.MX93 subset, if the imx93.dtsi include the
imx91.dtsi, the same problem will occur.
Common + delta is better than common - delta, so add imx91_93_common.dtsi
for i.MX91 and i.MX93, then the imx93.dtsi and imx91.dtsi will include the
imx91_93_common.dtsi.
Rename imx93.dtsi to imx91_93_common.dtsi and move i.MX93 specific
part from imx91_93_common.dtsi to imx93.dtsi.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The aliases is board level property rather than soc property, so move
these to each boards.
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
SolidRun Clearfog CX and Honeycomb have LX2160A PEX3 and PEX5 exposed on
physical connectors.
Vendor U-Boot used to patch status properties such that it went
undiscovered these nodes have their status set disabled.
Set status okay for pcie3 and pcie5 nodes.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
SolidRun LX2160A CEX-7 module has interrupts wired for both the rtc and
ethernet phy.
Add description for those interrupts to the rtc and phy nodes.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add description for the SolidRun i.MX8M Plus based System on Module, and
the CuBox-M.
The SoM features:
- 2x 1Gbps Ethernet with PHY
- eMMC
- 1/2/3/8GB DDR
- MIPI-CSI Camera Connector (not described without specific camera)
The CuBox-M is a complete product with enclosure featuring:
- 1x 1Gbps RJ45 Ethernet Port
- 2x USB-3.0 Type A
- HDMI connector
- microSD connector
- microUSB connector for console (using fdtdi chip)
- IR receiver
- RTC with backup battery
Signed-off-by: Josua Mayer <josua@solid-run.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Decoding interrupt-map is tricky, because it consists of five
components. Use known GIC_SPI define in final interrupt specifier
component makes easier to read.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add missing address-cells 0 to GIC interrupt node to silence W=1
warning:
imx8-ss-hsio.dtsi:71.3-74.28: Warning (interrupt_map): /bus@5f000000/pcie@5f010000:interrupt-map:
Missing property '#address-cells' in node /interrupt-controller@51a00000, using 0 as fallback
Value '0' is correct because:
1. GIC interrupt controller does not have children,
2. interrupt-map property (in PCI node) consists of five components and
the fourth component "parent unit address", which size is defined by
'#address-cells' of the node pointed to by the interrupt-parent
component, is not used (=0)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add missing address-cells 0 to GIC interrupt node to silence W=1
warning:
imx8qm-ss-hsio.dtsi:83.3-86.28: Warning (interrupt_map): /bus@5f000000/pcie@5f010000:interrupt-map:
Missing property '#address-cells' in node /interrupt-controller@51a00000, using 0 as fallback
Value '0' is correct because:
1. GIC interrupt controller does not have children,
2. interrupt-map property (in PCI node) consists of five components and
the fourth component "parent unit address", which size is defined by
'#address-cells' of the node pointed to by the interrupt-parent
component, is not used (=0)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add missing address-cells 0 to GIC interrupt node to silence W=1
warning:
imx8mq.dtsi:1746.4-1749.43: Warning (interrupt_map): /soc@0/pcie@33800000:interrupt-map:
Missing property '#address-cells' in node /soc@0/interrupt-controller@38800000, using 0 as fallback
Value '0' is correct because:
1. GIC interrupt controller does not have children,
2. interrupt-map property (in PCI node) consists of five components and
the fourth component "parent unit address", which size is defined by
'#address-cells' of the node pointed to by the interrupt-parent
component, is not used (=0)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add missing address-cells 0 to GIC interrupt node to silence W=1
warning:
imx8mp.dtsi:2184.4-2187.29: Warning (interrupt_map): /soc@0/pcie@33800000:interrupt-map:
Missing property '#address-cells' in node /soc@0/interrupt-controller@38800000, using 0 as fallback
Value '0' is correct because:
1. GIC interrupt controller does not have children,
2. interrupt-map property (in PCI node) consists of five components and
the fourth component "parent unit address", which size is defined by
'#address-cells' of the node pointed to by the interrupt-parent
component, is not used (=0)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add missing address-cells 0 to GIC interrupt node to silence W=1
warning:
imx8mm.dtsi:1355.4-1358.29: Warning (interrupt_map): /soc@0/pcie@33800000:interrupt-map:
Missing property '#address-cells' in node /soc@0/interrupt-controller@38800000, using 0 as fallback
Value '0' is correct because:
1. GIC interrupt controller does not have children,
2. interrupt-map property (in PCI node) consists of five components and
the fourth component "parent unit address", which size is defined by
'#address-cells' of the node pointed to by the interrupt-parent
component, is not used (=0)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add missing address-cells 0 to GIC interrupt node to silence W=1
warning:
imx8dxl-ss-hsio.dtsi:45.3-48.27: Warning (interrupt_map): /bus@5f000000/pcie@5f010000:interrupt-map:
Missing property '#address-cells' in node /interrupt-controller@51a00000, using 0 as fallback
Value '0' is correct because:
1. GIC interrupt controller does not have children,
2. interrupt-map property (in PCI node) consists of five components and
the fourth component "parent unit address", which size is defined by
'#address-cells' of the node pointed to by the interrupt-parent
component, is not used (=0)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add missing address-cells 0 to GIC interrupt node to silence W=1
warning:
fsl-ls1046a.dtsi:334.5-346.26: Warning (interrupt_map): /soc/scfg@1570000/interrupt-controller@1ac:interrupt-map:
Missing property '#address-cells' in node /interrupt-controller@1400000, using 0 as fallback
Value '0' is correct because:
1. GIC interrupt controller does not have children,
2. interrupt-map property (in PCI node) consists of five components and
the fourth component "parent unit address", which size is defined by
'#address-cells' of the node pointed to by the interrupt-parent
component, is not used (=0)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add missing address-cells 0 to GIC interrupt node to silence W=1
warning:
fsl-ls1043a.dtsi:330.5-342.26: Warning (interrupt_map): /soc/scfg@1570000/interrupt-controller@1ac:interrupt-map:
Missing property '#address-cells' in node /interrupt-controller@1400000, using 0 as fallback
Value '0' is correct because:
1. GIC interrupt controller does not have children,
2. interrupt-map property (in PCI node) consists of five components and
the fourth component "parent unit address", which size is defined by
'#address-cells' of the node pointed to by the interrupt-parent
component, is not used (=0)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add missing address-cells 0 to GIC interrupt node to silence W=1
warning:
fsl-ls1012a.dtsi:548.4-551.32: Warning (interrupt_map): /soc/pcie@3400000:interrupt-map:
Missing property '#address-cells' in node /interrupt-controller@1400000, using 0 as fallback
Value '0' is correct because:
1. GIC interrupt controller does not have children,
2. interrupt-map property (in PCI node) consists of five components and
the fourth component "parent unit address", which size is defined by
'#address-cells' of the node pointed to by the interrupt-parent
component, is not used (=0)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix the can tranceivers to actually use the new phy description instead
of the regulator tweak.
Signed-off-by: Maud Spierings <maudspierings@gocontroll.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for TechNexion EDM-G-IMX8M-PLUS SOM and WB-EDM-G carrier board.
Key interfaces include:
- Gigabit Ethernet
- USB 3.0
- I2S, UART, SPI, I2C, PWM, GPIO
Signed-off-by: Richard Hu <richard.hu@technexion.com>
Signed-off-by: Ray Chang <ray.chang@technexion.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The ISP HDR stitching registers are clocked by the pixel clock, which is
gated by the MIPI_CSI2 power domain. Attempting to access those
registers with the clock off locks up the system. Fix this by adding the
pclk clock and the MIPI_CSI2 secondary power domain.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add it to improve USB signal quality.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The DTS code coding style expects exactly one space around '=' or '{'
characters.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The drive strength is too high for SDR104 mode. Change the drive
strength to X3 as hardware team recommends.
Signed-off-by: Luke Wang <ziniu.wang_1@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
System Manager supports reading out pf09 and pf53 temperature and
SCMI Agent could get the values through SCMI sensor protocol. So add
the nodes to allow Linux to get the temperature.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
M.2 device only can be enabled after all Power Rails reach their minimum
operating voltage (PCI Express M.2 Specification r5.1 3.1.4 Power-up
Timing). Set a delay equal to the max value of Tsettle in m2 regulator.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add i2c, gpio, mmc, serial alias for 15x15 EVK and add lpuart5 serial
alias for 19x19 EVK.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add etf, etm, etr, funnel nodes for coresight.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add OCOTP node to allow reading fuse using nvmem API
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add more MUs for V2X communication
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add SCMI LMM and CPU nodes for managing Logical Machine and CPU.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add System Counter node to support cpuidle when arm generic timer stops
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to the imx95 RM, the lpuart7 rx and tx DMA's srcid are 88 and 87,
and the lpuart8 rx and tx DMA's srcid are 90 and 89. So correct them.
Fixes: 915fd2e127 ("arm64: dts: imx95: add edma[1..3] nodes")
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX 8DualXLite/8SoloXLite has a different connectivity memory map
than the generic i.MX8 has. One conflicting resource is usb, where the
imx8dxl has a second usb2 phy @5b110000, while the generic imx8 dtsi has
one usb2 phy and one usb3 phy, and the usb3otg @5b110000. When
including both imx8dxl-ss-conn.dtsi and imx8-ss-conn.dtsi as done in
imx8dxl.dtsi this leads to a duplicate unit-address warning.
The usb3otg node was introduced after the initial imx8dxl support with
commit a8bd7f1551 ("arm64: dts: imx8qxp: add cadence usb3 support")
and since then leads to warnings like this (when built with W=2):
DTC arch/arm64/boot/dts/freescale/imx8dxl-evk.dtb
…/arch/arm64/boot/dts/freescale/imx8-ss-conn.dtsi:148.24-182.4: Warning (unique_unit_address): /bus@5b000000/usb@5b110000: duplicate unit-address (also used in node /bus@5b000000/usbphy@5b110000)
also defined at …/arch/arm64/boot/dts/freescale/imx8dxl-ss-hsio.dtsi:41.23-50.4
also defined at …/arch/arm64/boot/dts/freescale/imx8dxl-evk.dts:645.8-653.3
Delete usb3 related nodes at dxl to fix above warning.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The SWT0 is directly connected to the reset line and only one instance
is useful for its purpose. Let's enable it on the s32g399a-rdb3.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Ghennadi Procopciuc <ghennadi.procopciuc@nxp.com>
Cc: Thomas Fossati <thomas.fossati@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Referred in the documentation as the Software Timer Watchdog (SWT),
the s32g3 has 12 watchdogs. The number of watchdogs is designed to
allow dedicating one watchdog per Cortex-M7/A53 present on the SoC.
Add the SWT nodes in the device tree.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Ghennadi Procopciuc <ghennadi.procopciuc@nxp.com>
Cc: Thomas Fossati <thomas.fossati@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The SWT0 is directly connected to the reset line and only one instance
is useful for its purpose. Let's enable it for the s32g274-rd2.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Ghennadi Procopciuc <ghennadi.procopciuc@nxp.com>
Cc: Thomas Fossati <thomas.fossati@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Referred in the documentation as the Software Timer Watchdog (SWT),
the s32g2 has 7 watchdogs. The number of watchdogs is designed to
allow dedicating one watchdog per Cortex-M7/A53 present on the SoC.
Add the SWT nodes in the device tree.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The platform has 8 CPUs, and the Linux STM timer driver is
instantiated per CPU. Enable 8 STM timers that can be used as
replacements for the ARM architected timers. The remaining STM timers
are not useful to the Linux kernel and provide no benefit, so they are
left disabled.
Enable STM0 to STM6 and STM8 on the s32g399a-rdb3 platform.
STM7 is skipped, as it differs slightly from the others and requires
an additional property to be properly handled by the driver.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Ghennadi Procopciuc <ghennadi.procopciuc@nxp.com>
Cc: Thomas Fossati <thomas.fossati@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The s32g3 has a STM module containing 12 timers. Each timer has a
dedicated interrupt and share the same clock.
Add the STM0->STM11 nodes for the s32g3 SoC. The STM7 node is not
added because it is slightly different and needs an extra property
which will be added later when supported by the driver.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Ghennadi Procopciuc <ghennadi.procopciuc@nxp.com>
Cc: Thomas Fossati <thomas.fossati@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable the timers STM0 -> STM3 on the s32g274-rd2
The platform has 4 CPUs, and the Linux STM timer driver is
instantiated per CPU. Enable 4 STM timers that can be used as
replacements for the ARM architected timers. The remaining STM timers
are not useful to the Linux kernel and provide no benefit, so they are
left disabled.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Ghennadi Procopciuc <ghennadi.procopciuc@nxp.com>
Cc: Thomas Fossati <thomas.fossati@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The s32g2 has a STM module containing 8 timers. Each timer has a
dedicated interrupt and share the same clock.
Add the timers STM0->STM6 nodes for the s32g2 SoC. The STM7 node is
not added because it is slightly different and needs an extra property
which will be added later when supported by the driver.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Ghennadi Procopciuc <ghennadi.procopciuc@nxp.com>
Cc: Thomas Fossati <thomas.fossati@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the err irq info for edma2 and edma4. These two err irq are
connected to the GIC directly, not irqsteer.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add initial support for TQMLS1012AL module mounted on MBLS1012AL.
It supports UART1 for console, PCIe, I2C, USB, µSD card (default), SATA
and QSPI.
There is an alternative ordering option which provides an eMMC instead of
an SD card. This uses a different DT instead.
Due missing Packet Forwarding Engine (PFE) driver support, there is no
support for Ethernet so far.
Signed-off-by: Max Merchel <Max.Merchel@tq-group.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The assignment of the USB ports is wrong and needs to be swapped.
The OTG (USB-C) port is on the first port and the host port with
the onboard hub is on the second port.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Fixes: 2b52fd6035 ("arm64: dts: Add support for Kontron i.MX93 OSM-S SoM and BL carrier board")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
