The Moduline Mini is a part of the wider GOcontroll Moduline ecosystem. These
are embedded controllers that focus on modularity with their swappable IO
modules.
Features:
- up to 4 Moduline IO modules
- 2 CAN busses
- 1 Ethernet
- 4 RGB leds
- 1 3D accelerometer
- optional Wi-Fi/Bluetooth
- optional 4G/GPS
Signed-off-by: Maud Spierings <maudspierings@gocontroll.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
The Moduline IV is a part of the wider GOcontroll Moduline ecosystem. These
are embedded controllers that focus on modularity with their swappable IO
modules.
Features:
- up to 8 Moduline IO modules
- 4 CAN busses
- 1 LIN bus
- 1 Ethernet
- 4 RGB leds
- optional Wi-Fi/Bluetooth
- optional 4G/GPS
Signed-off-by: Maud Spierings <maudspierings@gocontroll.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
The Ka-Ro Electronics tx8m-1610 is a COM based on the imx8mm SOC. It has
1 GB of ram and 4 GB of eMMC storage on board.
Add it to enable boards based on this module
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Maud Spierings <maudspierings@gocontroll.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Currently to configure each IOMUXC_SW_PAD_CTL_PAD the raw value of this
register is written in the dts, these values are not obvious. Add defines
which describe the fields of this register which can be or-ed together to
produce readable settings.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Maud Spierings <maudspierings@gocontroll.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add DeviceTree support for the NXP FRDM-IMX91S development board based
on the i.MX91 SoC. FRDM-IMX91S is a cost-optimized variant of FRDM-IMX91
and differs in memory, storage, Ethernet, and PMIC configuration:
- 512MB LPDDR4 (FRDM-IMX91 uses 1GB)
- 256MB FlexSPI-NAND (FRDM-IMX91 uses 8GB eMMC)
- Single GbE port (FRDM-IMX91 has dual GbE)
- PMIC PF9453 (FRDM-IMX91 uses PCA9451A)
This DT enables:
- ADC1
- UART1 and UART5
- I2C bus and children nodes
- USB and related nodes
- uSDHC1 and uSDHC2
- FlexSPI NAND flash
- Watchdog3
- Ethernet (eqos)
- FlexCAN
- MQS
Link: https://www.nxp.com/design/design-center/development-boards-and-designs/FRDM-IMX91S
(FRDM-IMX91S board page)
Link: https://www.nxp.com/design/design-center/development-boards-and-designs/FRDM-IMX91
(FRDM-IMX91 board page)
Co-developed-by: Lei Xu <lei.xu@nxp.com>
Signed-off-by: Lei Xu <lei.xu@nxp.com>
Co-developed-by: Xiaofeng Wei <xiaofeng.wei@nxp.com>
Signed-off-by: Xiaofeng Wei <xiaofeng.wei@nxp.com>
Signed-off-by: Yanan Yang <yanan.yang@nxp.com>
Tested-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add usdhc3 to support M.2 SDIO WiFi on i.MX91 11x11 EVK board.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add usdhc1 to support M.2 SDIO WiFi on i.MX8MP EVK board.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
The current pin configuration for MX8MP_IOMUXC_SD1_DATA4__GPIO2_IO06
sets the weak pull-up but does not enable the pull select field.
Bit 8 in the IOMUX register must be set in order for the weak pull-up
to actually take effect.
Update the pinctrl setting from 0x40 to 0x140 to enable both the pull
select and the weak pull-up, ensuring the line behaves as expected.
Fixes: d506505000 ("arm64: dts: imx8mp-evk: Add PCIe support")
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add usdhc3 to support M.2 SDIO WiFi on i.MX943 EVK board.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add spi nor flash MT35XU01G support, it support OCT DTR mode
at 200MHz.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
During system resume, the following errors occurred:
[ 430.638625] mmc1: error -84 writing Cache Enable bit
[ 430.643618] mmc1: error -84 doing runtime resume
For eMMC and SD, there are two tuning pass windows and the gap between
those two windows may only have one cell. If tuning step > 1, the gap may
just be skipped and host assumes those two windows as a continuous
windows. This will cause a wrong delay cell near the gap to be selected.
Set the tuning step to 1 to avoid selecting the wrong delay cell.
For SDIO, the gap is sufficiently large, so the default tuning step does
not cause this issue.
Fixes: e37907bd82 ("arm64: dts: freescale: add i.MX93 11x11 EVK basic support")
Signed-off-by: Luke Wang <ziniu.wang_1@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
During system resume, the following errors occurred:
[ 430.638625] mmc1: error -84 writing Cache Enable bit
[ 430.643618] mmc1: error -84 doing runtime resume
For eMMC and SD, there are two tuning pass windows and the gap between
those two windows may only have one cell. If tuning step > 1, the gap may
just be skipped and host assumes those two windows as a continuous
windows. This will cause a wrong delay cell near the gap to be selected.
Set the tuning step to 1 to avoid selecting the wrong delay cell.
For SDIO, the gap is sufficiently large, so the default tuning step does
not cause this issue.
Fixes: 6772c4cffd ("arm64: dts: freescale: add i.MX91 11x11 EVK basic support")
Signed-off-by: Luke Wang <ziniu.wang_1@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Have reserved eDMA2 channels 0 and 1 for V2X fast hash in imx95.dtsi.
So update the dma-channel-mask from 0xc0000000 to 0xc0000003 to mark
channels 0, 1, 30, and 31 as reserved.
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reserve eDMA channels 0 and 1 on the AXI eDMA controller for exclusive
use by V2X (Vehicle-to-Everything) fast hash operations.
Reviewed-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Tested-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
i.MX93 Wireless SiP is created by integrating i.MX93 and IW610 WLCSP
(Wi-Fi + BLE + 802.15.4). And i.MX93 Wireless EVK board with the i.MX93
Wireless SiP basically reuse the i.MX93 11x11 EVK board, with some minor
functional and pin connection differences. Reuse the new
imx93-11x11-evk-common.dtsi and add the board-specific changes here.
Here are the detailed differences between i.MX93 Wireless EVK and i.MX93
11x11 EVK board.
Function differences:
Function i.MX93W EVK i.MX93 EVK
WIFI/BT IW610 in i.MX93W IW612 M.2 module
MQS N Y
PDM MIC N Y
M.2 N Y
RPi 40-pin HDR Limited support(pin conflict) Y
Pin connection differences:
Function Signal name i.MX93W EVK i.MX93 EVK
WIFI/BT SPI_FRM SAI1_TXFS (spi1.PCS0) GPIO_IO08 (spi3.PCS0)
SPI_TXD SAI1_TXC (spi1.SIN) GPIO_IO09 (spi3.SIN)
SPI_RXD SAI1_RXD0 (spi1.SOUT) GPIO_IO10 (spi3.SOUT)
SPI_CLK SAI1_TXD0 (spi1.SCK) GPIO_IO11 (spi3.SCK)
SPI_INT CCM_CLKO1 on-board IO expander
NB_WAKE_IN PDM_CLK on-module IO expander
WL_WAKE_IN PDM_BIT_STREAM0 on-module IO expander
IND_RST_WL PDM_BIT_STREAM1 on-module IO expander
IND_RST_NB GPIO_IO28 on-module IO expander
PDn GPIO_IO29 on-module IO expander
NB_WAKE_OUT GPIO_IO14 on-board IO expander
WL_WAKE_OUT GPIO_IO15 CCM_CLKO1
I2C3 I2C3_SDA GPIO_IO00 GPIO_IO28
I2C3_SCL GPIO_IO01 GPIO_IO29
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Introduce imx93w.dtsi to describe the new NXP i.MX93 Wireless SiP, which
integrates the i.MX93 application processor with the NXP IW610 WLCSP
(Wi-Fi + Bluetooth LE + 802.15.4) connectivity device.
The new imx93w.dtsi is based on imx93.dtsi and adds the pieces required
for the internal connection between i.MX93 and IW610 inside the SiP.
This includes USDHC3 which is used as the host interface to the IW610
and the required GPIO settings(e.g. WL_RST, WL_REG_ON, etc.).
These nodes reflect internal SiP wiring and are not board specific, so
they are placed in a dedicated imx93w.dtsi file that can be reused by
multiple boards adopting the i.MX93 Wireless SiP.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
The previous patch renamed imx93-11x11-evk.dts to
imx93-11x11-evk-common.dtsi to prepare for adding the i.MX93 Wireless
EVK, which shares most of its design with the 11x11 EVK.
Move the board specific differences out of imx93-11x11-evk-common.dtsi
and back into imx93-11x11-evk.dts, ensuring that the common dtsi only
contains the truly shared parts between the two EVK boards.
No functional changes intended.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
The i.MX93 Wireless EVK reuses most of the 11x11 EVK design. To avoid
duplication and DTS-to-DTS includes, extract the common parts into a new
imx93-11x11-evk-common.dtsi shared by both boards.
Rename imx93-11x11-evk.dts to imx93-11x11-evk-common.dtsi and include it
from imx93-11x11-evk.dts.
Only structural changes are introduced, with no intended functional
impact.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add support for AONMIX MQS (i.e. MQS1).
Reviewed-by: Chancel Liu <chancel.liu@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add DT node for AONMIX MQS (i.e. MQS1).
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Fix the PMIC_SD2_VSEL gpio-line-name position. It should be on line 19
of gpio3, not line 20.
Fixes: 90bbe88e0e ("arm64: dts: freescale: add Toradex SMARC iMX95")
Cc: stable@vger.kernel.org
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Ixora boards have multiple instances of status leds, to avoid a name
collision add the function-enumerator property.
This fixes the following Linux kernel warnings:
leds-gpio leds: Led green:status renamed to green:status_1 due to name collision
leds-gpio leds: Led red:status renamed to red:status_1 due to name collision
Fixes: c083131c90 ("arm64: dts: freescale: add apalis imx8 aka quadmax carrier board support")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
The GPU is supported since Linux v6.9, with changes in the SoC dtsi
file. Remove the related obsolete TODO comment.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Enable lpuart6 for Bluetooth support.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Enable lpuart5 for Bluetooth support.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
The audmix is not used on apalis imx8, disable it.
This solves the following warning message
imx-audmix imx-audmix.0: failed to find SAI platform device
imx-audmix imx-audmix.0: probe with driver imx-audmix failed with error -22
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Enable lpuart5 on imx95-19x19-evk board for Bluetooth support.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
For i.MX93 11x11 EVK and 9x9 QSB boards, add the gpio-hog to enable the
M.2 PCM pins level shifter connected between soc sai1 interface and M.2
PCM pins so that HFP feature can be supported.
Since the HFP is only used at a later stage — after the BT firmware has
been downloaded and the BT connection with the remote device has been
established — both the pcal6524 expander and sai1 interface are already
fully initialized and available by that time. Therefore, using a
gpio-hog here will not introduce any probe ordering or dependency issues
for the HFP use case.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add required OF nodes to support the i.MX93 parallel output (DPI) path.
On the i.MX93 a single LCDIF is connected to three bridges: DPI, LVDS
LDB and the MIPI-DSI whereas the i.MX91 support only the DPI bridge.
Map endpoint@0 as DPI bridge output since the i.MX93 TRM (Figure 485.
MEDIAMIX block diagram) doesn't mention any port-number <-> bridge
combination.
Set the MEDIA-AXI and MEDIA-APB clocks to the overdrive (OD) values
since the i.MX93 and i.MX91 use the overdrive (OD) clk settings per
default.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add bus recovery feature for I2C buses on the PHYTEC phyCORE-i.MX93 SoM
based boards (that is phyBOARD-Nash-i.MX93 and phyBOARD-Segin-i.MX93).
This enables the i2c-imx-lpi2c driver to recover the stuck I2C bus by
switching the SCL and SDA pinmuxing and do the I2C bus bit-banging.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add bluetooth dts node.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add uart1 and bluetooth node.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Correct the spdif compatible string to "fsl,imx8mm-spdif".
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
- Fix a build error on parisc
- Remove the non-large-folio-aware function fsverity_verify_page()
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQSacvsUNc7UX4ntmEPzXCl4vpKOKwUCaZtg+xQcZWJpZ2dlcnNA
a2VybmVsLm9yZwAKCRDzXCl4vpKOKwQ+AQCiXEYAibl3vHRgQo7qEPCC5or4FtkF
HZ0ERRArhsU17AD/TKHE/AJkyFrwK4rGTb6I9Wi1OXnpG7jihZlYjj03Ag4=
=CUql
-----END PGP SIGNATURE-----
Merge tag 'fsverity-for-linus' of git://git.kernel.org/pub/scm/fs/fsverity/linux
Pull fsverity fixes from Eric Biggers:
- Fix a build error on parisc
- Remove the non-large-folio-aware function fsverity_verify_page()
* tag 'fsverity-for-linus' of git://git.kernel.org/pub/scm/fs/fsverity/linux:
fsverity: fix build error by adding fsverity_readahead() stub
fsverity: remove fsverity_verify_page()
f2fs: make f2fs_verify_cluster() partially large-folio-aware
f2fs: remove unnecessary ClearPageUptodate in f2fs_verify_cluster()
Fix a big endian specific issue in the PPC64-optimized AES code.
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQSacvsUNc7UX4ntmEPzXCl4vpKOKwUCaZtiphQcZWJpZ2dlcnNA
a2VybmVsLm9yZwAKCRDzXCl4vpKOK/z2AQD1j15Ao3iDW3yBSyTS+tFJaRUVDtjg
bNostoNJAjMM9wD/X0oAnt95WTNkdHexs+2aMzQ4ULKFRcwQrUTarKx7IgY=
=Dmfx
-----END PGP SIGNATURE-----
Merge tag 'libcrypto-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiggers/linux
Pull crypto library fix from Eric Biggers:
"Fix a big endian specific issue in the PPC64-optimized AES code"
* tag 'libcrypto-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiggers/linux:
lib/crypto: powerpc/aes: Fix rndkey_from_vsx() on big endian CPUs
Stephen retired and stepped back from -next maintainership, update his
entry in CREDITS to recognise his 18 years of hard work making it what
it is today and all the impact it's had on our development process.
Also update to his current GnuPG key while we're here.
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: SeongJae Park <sj@kernel.org>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The x509 public key code gained a dependency on the sha256 hash
implementation, causing a rare link time failure in randconfig
builds:
arm-linux-gnueabi-ld: crypto/asymmetric_keys/x509_public_key.o: in function `x509_get_sig_params':
x509_public_key.c:(.text.x509_get_sig_params+0x12): undefined reference to `sha256'
arm-linux-gnueabi-ld: (sha256): Unknown destination type (ARM/Thumb) in crypto/asymmetric_keys/x509_public_key.o
x509_public_key.c:(.text.x509_get_sig_params+0x12): dangerous relocation: unsupported relocation
Select the necessary library code from Kconfig.
Fixes: 2c62068ac8 ("x509: Separately calculate sha256 for blacklist")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Eric Biggers <ebiggers@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Align to the commit bf4afc53b7 ("Convert 'alloc_obj' family to use the
new default GFP_KERNEL argument") update the 'kmalloc_obj' declaration
for userspace to fix below compile error:
In file included from arch/arm/boot/compressed/../../../../lib/decompress_unxz.c:241,
from arch/arm/boot/compressed/decompress.c:56:
arch/arm/boot/compressed/../../../../lib/xz/xz_dec_stream.c: In function 'xz_dec_init':
arch/arm/boot/compressed/../../../../lib/xz/xz_dec_stream.c:787:28: error: implicit declaration of function 'kmalloc_obj'; did you mean 'kmalloc'? [-Wimplicit-function-declaration]
787 | struct xz_dec *s = kmalloc_obj(*s);
| ^~~~~~~~~~~
| kmalloc
Signed-off-by: Haiyue Wang <haiyuewa@163.com>
Fixes: 69050f8d6d ("treewide: Replace kmalloc with kmalloc_obj for non-scalar types")
Fixes: bf4afc53b7 ("Convert 'alloc_obj' family to use the new default GFP_KERNEL argument")
Reviewed-by: Kees Cook <kees@kernel.org>
Acked-by: Lasse Collin <lasse.collin@tukaani.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Toolchain and infrastructure:
- Pass '-Zunstable-options' flag required by the future Rust 1.95.0.
- Fix 'objtool' warning for Rust 1.84.0.
'kernel' crate:
- 'irq' module: add missing bound detected by the future Rust 1.95.0.
- 'list' module: add missing 'unsafe' blocks and placeholder safety
comments to macros (an issue for future callers within the crate).
'pin-init' crate:
- Clean Clippy warning that changed behavior in the future Rust 1.95.0.
-----BEGIN PGP SIGNATURE-----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=DOG1
-----END PGP SIGNATURE-----
Merge tag 'rust-fixes-7.0' of git://git.kernel.org/pub/scm/linux/kernel/git/ojeda/linux
Pull rust fixes from Miguel Ojeda:
"Toolchain and infrastructure:
- Pass '-Zunstable-options' flag required by the future Rust 1.95.0
- Fix 'objtool' warning for Rust 1.84.0
'kernel' crate:
- 'irq' module: add missing bound detected by the future Rust 1.95.0
- 'list' module: add missing 'unsafe' blocks and placeholder safety
comments to macros (an issue for future callers within the crate)
'pin-init' crate:
- Clean Clippy warning that changed behavior in the future Rust
1.95.0"
* tag 'rust-fixes-7.0' of git://git.kernel.org/pub/scm/linux/kernel/git/ojeda/linux:
rust: list: Add unsafe blocks for container_of and safety comments
rust: pin-init: replace clippy `expect` with `allow`
rust: irq: add `'static` bounds to irq callbacks
objtool/rust: add one more `noreturn` Rust function
rust: kbuild: pass `-Zunstable-options` for Rust 1.95.0
Summary of changes:
- Fix multiple definition of __pcpu_unique_da_mon_this
After refactoring monitors, we used static per-cpu variables with the
same names across different per-cpu monitors. This is explicitly
disallowed for modules on some architectures (alpha) or if
CONFIG_DEBUG_FORCE_WEAK_PER_CPU is enabled (e.g. Fedora's debug
kernel). Make sure all those variables have different names to avoid
compilation issues.
-----BEGIN PGP SIGNATURE-----
iIoEABYKADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCaZoJ1BQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qkykAP41lj9VAe0dM81f20IfOBhqIBZPS6MP
ajRGZ9bz1ZiJwwD/dHm+APheD7umImzoDXpW1IJxgNPlZTnpte3WyhIYaQs=
=HxRz
-----END PGP SIGNATURE-----
Merge tag 'trace-rv-7.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull runtime verifier fix from Steven Rostedt:
- Fix multiple definition of __pcpu_unique_da_mon_this
After refactoring monitors, we used static per-cpu variables with the
same names across different per-cpu monitors. This is explicitly
disallowed for modules on some architectures (alpha) or if
CONFIG_DEBUG_FORCE_WEAK_PER_CPU is enabled (e.g. Fedora's debug
kernel). Make sure all those variables have different names to avoid
compilation issues.
* tag 'trace-rv-7.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
rv: Fix multiple definition of __pcpu_unique_da_mon_this
This converts some of the visually simpler cases that have been split
over multiple lines. I only did the ones that are easy to verify the
resulting diff by having just that final GFP_KERNEL argument on the next
line.
Somebody should probably do a proper coccinelle script for this, but for
me the trivial script actually resulted in an assertion failure in the
middle of the script. I probably had made it a bit _too_ trivial.
So after fighting that far a while I decided to just do some of the
syntactically simpler cases with variations of the previous 'sed'
scripts.
The more syntactically complex multi-line cases would mostly really want
whitespace cleanup anyway.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the exact same thing as the 'alloc_obj()' version, only much
smaller because there are a lot fewer users of the *alloc_flex()
interface.
As with alloc_obj() version, this was done entirely with mindless brute
force, using the same script, except using 'flex' in the pattern rather
than 'objs*'.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
