The Lenovo IdeaCentre Mini X (Snapdragon) Desktop is a Hamoa-based
ultracompact desktop PC. It provides HDMI, DisplayPort, USB Type-C
display outputs, 5 additional USB ports, Ethernet, dual NVME slots,
headphone jack, WiFi, and Bluetooth.
Introduce a DeviceTree describing this device.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260401-ideacentre-v2-2-5745fe2c764e@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Enable IMX577 via CCI on Talos EVK Core Kit.
The Talos EVK board does not include a camera sensor
by default. This DTSO has enabled the Arducam 12.3MP
IMX577 Mini Camera Module on the CSI-1 interface.
CSI-1 interface using mclk2 as the MCLK source on this board.
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Wenmeng Liu <wenmeng.liu@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260305-sm6150_evk-v6-5-38ce4360d5e0@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
All the existing variants Talos boards are using Gunyah hypervisor
which means that, so far, Linux-based OS could only boot in EL1 on
those devices. However, it is possible for us to boot Linux at EL2
on these devices [1].
When running under Gunyah, the remote processor firmware IOMMU streams
are controlled by Gunyah. However, without Gunyah, the IOMMU is managed
by the consumer of this DeviceTree. Therefore, describe the firmware
streams for each remote processor.
Add a EL2-specific DT overlay and apply it to Talos IOT variant
devices to create -el2.dtb for each of them alongside "normal" dtb.
[1]
https://docs.qualcomm.com/bundle/publicresource/topics/80-70020-4/boot-developer-touchpoints.html#uefi
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Mukesh Ojha <mukesh.ojha@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260127-talos-el2-overlay-v2-3-b6a2266532c4@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add the device tree for the QCS615-based Talos EVK platform. The
platform is composed of a System-on-Module following the SMARC
standard, and a Carrier Board.
The Carrier Board supports several display configurations, HDMI and
LVDS. Both configurations use the same base hardware, with the display
selection controlled by a DIP switch.
Use a DTBO file, talos-evk-lvds-auo,g133han01.dtso, which defines an
overlay that disables HDMI and adds LVDS. The DTs file talos-evk
can describe the HDMI display configurations.
According to the hardware design and vendor guidance, the WiFi PA
supplies VDD_PA_A and VDD_PA_B only need to be enabled at the same time
as asserting WLAN_EN.
On this platform, WiFi enablement is controlled via the WLAN_EN GPIO
(GPIO84), which also drives the VDD_PA_A and VDD_PA_B power enables.
Remove the VDD_PA_A and VDD_PA_B regulator nodes from the device tree
and rely on WLAN_EN to enable WiFi functionality.
Add talos-evk-usb1-peripheral.dtso overlay to enable USB0 peripheral
(EDL) mode. The base DTS will keep USB0 host-only due to hardware
routing through the EDL DIP switch, and the overlay switches the
configuration for device-mode operation.
The LVDS backlight hardware has been updated to use a simplified
design. The backlight enable signal is now permanently pulled up
to 3.3V and is no longer controlled via GPIO59.
Remove the GPIO59 based backlight configuration from the device
tree, as it is no longer routed to the LVDS interface.
The initial device tree includes support for:
- CPU and memory
- UART
- GPIOs
- Regulators
- PMIC
- Early console
- AT24MAC602 EEPROM
- MCP2515 SPI to CAN
- ADV7535 DSI-to-HDMI bridge
- DisplayPort interface
- SN65DSI84ZXHR DSI-to-LVDS bridge
- Wi-Fi/BT
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Sudarshan Shetty <tessolveupstream@gmail.com>
Link: https://lore.kernel.org/r/20260331060107.501561-4-tessolveupstream@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The SM8550-HDK board may be connected to a Display Card external PCB,
which is identical to the already supported SM8650-HDK Display Card,
it provides a VTDR6130 display with Goodix Berlin Touch controller, see
also commit bc90f56a16 ("arm64: dts: sm8650-hdk: add support for the
Display Card overlay") for additional details.
Two overlays are added to support SM8550-HDK plus Display Card and
SM8550-HDK plus Display Card plus Rear Camera Card setups.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260311001238.4191034-1-vladimir.zapolskiy@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Samsung Galaxy Core Prime Verizon Wireless is a phone based on MSM8916.
They are similar to the other Samsung devices based on MSM8916 with only a
few minor differences.
The device trees contain initial support with:
- GPIO keys
- Regulator haptic
- SDHCI (internal and external storage)
- USB Device Mode
- UART (on USB connector via the SM5502 MUIC)
- WCNSS (WiFi/BT)
- Regulators
- QDSP6 audio
- Speaker/earpiece/headphones/microphones via digital/analog codec in
MSM8916/PM8916
- WWAN Internet via BAM-DMUX
- PMIC and charger
- Touchscreen
There are different variants of Core Prime, with some differences in
NFC and MUIC.
The common parts are shared in
msm8916-samsung-fortuna-common.dtsi and msm8916-samsung-rossa-common.dtsi
to reduce duplication.
Signed-off-by: Max McNamee <maxmcnamee@proton.me>
[Raymond: Refactor touchscreen and MUIC. Add commit messages.]
Signed-off-by: Raymond Hackley <raymondhackley@protonmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260223220514.2556033-4-wonderfulshrinemaidenofparadise@postmarketos.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The Interface Plus [IFP] Mezzanine is an hardware expansion add-on
board designed to be stacked on top of Lemans EVK.
It has following peripherals :
- 4x Type A USB ports in host mode.
- TC9563 PCIe switch, which has following three downstream ports (DSP) :
- 1st DSP is routed to an M.2 E-key connector, intended for
WLAN modules.
- 2nd DSP is routed to an M.2 B-key connector, intended for
cellular modems.
- 3rd DSP with support for Dual Ethernet ports.
- eMMC.
- Additional 2.5GbE Ethernet PHY connected to native EMAC with support for
MAC Address configuration via NVMEM.
- EEPROM.
- LVDS Display.
- 2*mini DP.
Add support for following peripherals :
- TC9563 PCIe Switch.
- Additional 2.5GbE Ethernet Port.
- EEPROM.
Enable support for USB hub, LVDS display and mini-DP later once
dependent changes are available in lemans-evk core-kit.
Written with inputs from :
Mohd Ayaan Anwar <mohd.anwar@oss.qualcomm.com> - Ethernet.
Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com> - PCIe
Monish Chunara <monish.chunara@oss.qualcomm.com> - EEPROM.
Signed-off-by: Umang Chheda <umang.chheda@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260304165925.1535938-2-umang.chheda@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The IFP Mezzanine is an hardware expansion add-on board designed
to be stacked on top of Monaco EVK.
It has following peripherals :
- 4x Type A USB ports in host mode.
- TC9563 PCIe switch, which has following three downstream ports (DSP) :
- 1st DSP is routed to an M.2 E-Key connector, intended for
WLAN modules.
- 2nd DSP is routed to an M.2 B-key connector, intended for
cellular modems.
- 3rd DSP with support for Dual Ethernet ports.
- EEPROM.
- LVDS Display.
- 2*mini DP.
Add support for following peripherals :
- TC9563 PCIe Switch.
- EEPROM.
Enable support for USB hub, LVDS display and mini-DP later once dependent
changes are available in monaco-evk core-kit.
Written with inputs from :
Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com> - PCIe
Monish Chunara <monish.chunara@oss.qualcomm.com> - EEPROM.
Signed-off-by: Umang Chheda <umang.chheda@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260303164314.886733-2-umang.chheda@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Redmi Go (tiare) is like Redmi 5A with small differences like charging,
fuel gauge and different speaker codec.
Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260315-riva-common-v3-6-897f130786ed@mainlining.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Redmi 4A (rolex) is like Redmi 5A with small differences like charging,
fuel gauge, different speaker codec configuration and display.
Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260315-riva-common-v3-5-897f130786ed@mainlining.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add initial Device Tree for the Ayaneo Pocket S2 gaming console based
on the Qualcomm Snapdragon 8 Gen 3 platform.
The design is similar to a phone without the modem, the game control
is handled via a standalone controller connected to a PCIe USB
controller.
Display panel support will be added in a second time.
Signed-off-by: KancyJoe <kancy2333@outlook.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20260319-topic-sm8650-ayaneo-pocket-s2-base-v6-5-797bf96df771@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add device tree support for the Arduino VENTUNO Q board,
based on the Qualcomm QCS8300 (Monaco) SoC.
The board features a Qualcomm Monza SoM and integrates various
peripherals, including:
- USB Type‑C connector with dual‑role support
- ADV7535 DSI‑to‑HDMI bridge
- MAX98091 audio codec
- 2.5G Ethernet PHY (HSGMII)
- PCIe0 (to onboard WiFi chipset and USB bridge)
- PCIe1 (to M2/nvme)
- Button (via GPIO‑keys)
Signed-off-by: Loic Poulain <loic.poulain@oss.qualcomm.com>
Co-developed-by: Srinivas Kandagatla <srinivas.kandagatla@oss.qualcomm.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260313103824.2634519-7-srinivas.kandagatla@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The MTP is a one of the boards that comes with the Eliza SoC.
So add dedicated board dts for it.
The initial support enables:
- UART debug console
- Ob-board UFS storage
- Qualcomm RPMh regulators (PMIC) and VPH_PWR
- board specific clocks & reserved GPIO ranges
Co-developed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260318-eliza-base-dt-v3-3-8a50bd2201ed@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Introduce support for the Mahua SoC and the CRD based on it. Some of
the notable differences are the absent CPU cluster, interconnect, TLMM,
thermal zones and adjusted PCIe west clocks. Everything else should
work as-is.
Co-developed-by: Raviteja Laggyshetty <raviteja.laggyshetty@oss.qualcomm.com>
Signed-off-by: Raviteja Laggyshetty <raviteja.laggyshetty@oss.qualcomm.com>
Co-developed-by: Kamal Wadhwa <kamal.wadhwa@oss.qualcomm.com>
Signed-off-by: Kamal Wadhwa <kamal.wadhwa@oss.qualcomm.com>
Co-developed-by: Manaf Meethalavalappu Pallikunhi <manaf.pallikunhi@oss.qualcomm.com>
Signed-off-by: Manaf Meethalavalappu Pallikunhi <manaf.pallikunhi@oss.qualcomm.com>
Signed-off-by: Gopikrishna Garmidi <gopikrishna.garmidi@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260318124100.212992-4-gopikrishna.garmidi@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The DeviceTree for the OLED variant of the Microsoft Surface Pro 11th
Edition was originally added in commit '0d72ccaa1e84 ("arm64: dts: qcom:
Add support for X1-based Surface Pro 11")'. The original patch on the
mailing list also added the new device tree to the Makefile but that
part seems to have been dropped (by accident) when it got merged.
Signed-off-by: Tobias Heider <tobias.heider@canonical.com>
Fixes: 0d72ccaa1e ("arm64: dts: qcom: Add support for X1-based Surface Pro 11")
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260226140429.232544-3-tobias.heider@canonical.com
[bjorn: Rewrote commit message reference to offending commit]
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Monaco EVK board does not include a camera sensor in its default hardware
configuration. Introducing a device tree overlay to support optional
integration of the IMX577 sensor via CSIPHY1.
Camera reset is handled through an I2C expander, and power is enabled
via TLMM GPIO74.
An example media-ctl pipeline for the imx577 is:
media-ctl --reset
media-ctl -V '"imx577 3-001a":0[fmt:SRGGB10/4056x3040 field:none]'
media-ctl -V '"msm_csiphy1":0[fmt:SRGGB10/4056x3040]'
media-ctl -V '"msm_csid0":0[fmt:SRGGB10/4056x3040]'
media-ctl -V '"msm_vfe0_rdi0":0[fmt:SRGGB10/4056x3040]'
media-ctl -l '"msm_csiphy1":1->"msm_csid0":0[1]'
media-ctl -l '"msm_csid0":1->"msm_vfe0_rdi0":0[1]'
yavta -B capture-mplane -c -I -n 5 -f SRGGB10P -s 4056x3040 -F /dev/video1
Co-developed-by: Ravi Shankar <quic_rshankar@quicinc.com>
Signed-off-by: Ravi Shankar <quic_rshankar@quicinc.com>
Co-developed-by: Vishal Verma <quic_vishverm@quicinc.com>
Signed-off-by: Vishal Verma <quic_vishverm@quicinc.com>
Signed-off-by: Nihal Kumar Gupta <quic_nihalkum@quicinc.com>
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260213132058.521474-6-quic_nihalkum@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Thundercomm AI MiniPC G1 IoT is single board computer with
AI capability based on Qualcomm QCS6490 platform.
This device tree is confirmed to work as below:
- GPU
- HDMI output port
- PCIe M.2 port (for external Wi-Fi or 5G connectivity)
- UART / serial console port
- UFS
- USB Type-C port, with Display Port
Signed-off-by: Roger Shimizu <rosh@debian.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260207-next-20260130_rosh-v2-3-548bbe0c7742@debian.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
RDP433/RDP418 can have NAND or eMMC based on a board level rework. Since
the same GPIOS are used for both the interfaces, only one of them can be
used. Add a new DTS file to enable eMMC.
Signed-off-by: Varadarajan Narayanan <varadarajan.narayanan@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260205085936.3220108-5-varadarajan.narayanan@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
All the Monaco IOT variants boards are using Gunyah hypervisor which
means that, so far, Linux-based OS could only boot in EL1 on those
devices. However, it is possible for us to boot Linux at EL2 on these
devices [1].
When running under Gunyah, the remote processor firmware IOMMU streams
are controlled by Gunyah. However, without Gunyah, the IOMMU is managed
by the consumer of this DeviceTree. Therefore, describe the firmware
streams for each remote processor.
Add a EL2-specific DT overlay and apply it to Monaco IOT variant
devices to create -el2.dtb for each of them alongside "normal" dtb.
[1]
https://docs.qualcomm.com/bundle/publicresource/topics/80-70020-4/boot-developer-touchpoints.html#uefi
Signed-off-by: Mukesh Ojha <mukesh.ojha@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260127-talos-el2-overlay-v2-2-b6a2266532c4@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add support for building an EL2 combined DTB for the hamoa-evk
in the Qualcomm DTS Makefile.
The new hamoa-iot-evk-el2.dtb is generated by combining the base
hamoa-iot-evk.dtb with the x1-el2.dtbo overlay, enabling EL2-specific
configurations required by the platform.
Signed-off-by: Xin Liu <xin.liu@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260127062425.1084673-1-xin.liu@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The PURWA-IOT-EVK is an evaluation platform for IoT products, composed of
the Purwa IoT SoM and a carrier board. Together, they form a complete
embedded system capable of booting to UART.
PURWA-IOT-EVK uses the PS8833 as a retimer for USB0, unlike HAMOA-IOT-EVK.
Meanwhile, USB0 bypasses the SBU selector FSUSB42.
Make the following peripherals on the carrier board enabled:
- UART
- On-board regulators
- USB Type-C mux
- Pinctrl
- Embedded USB (EUSB) repeaters
- NVMe
- pmic-glink
- USB DisplayPorts
- Bluetooth
- WLAN
- Audio
- PCIe ports for PCIe3 through PCIe6a
- TPM
Signed-off-by: Yijie Yang <yijie.yang@oss.qualcomm.com>
Reviewed-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260202073555.1345260-4-yijie.yang@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Redmi Note 8T (willow) is very similar to Redmi Note 8 (ginkgo)
the only difference is willow have NFC.
Make a common base from ginkgo devicetree for both device.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260126-xiaomi-willow-v3-7-aad7b106c311@mainlining.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
There has been a (rare) variant of Dragonboard 820c, utilizing Pro
version of the SoC, with the major difference being CPU and GPU clock
tables. Add a DT file representing this version of the board.
01:13:26.275: B - 417880 - 8996 Pro v1.x detected, Max frequency = 1.8 GHz
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251111-db820c-pro-v1-2-6eece16c5c23@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add initial device tree support for the Glymur Compute Reference
Device(CRD) board, with this board dts glymur crd can boot to shell
with rootfs on nvme and uart21 as serial console
Features enabled are:
- Board and sleep clocks
- Volume up/down keys
- Regulators 0 - 4
- Power supplies and sideband signals (PERST, WAKE, CLKREQ) for
PCIe3b/4/5/6 controllers and PHYs
Co-developed-by: Kamal Wadhwa <kamal.wadhwa@oss.qualcomm.com>
Signed-off-by: Kamal Wadhwa <kamal.wadhwa@oss.qualcomm.com>
Co-developed-by: Qiang Yu <qiang.yu@oss.qualcomm.com>
Signed-off-by: Qiang Yu <qiang.yu@oss.qualcomm.com>
Co-developed-by: Sibi Sankar <sibi.sankar@oss.qualcomm.com>
Signed-off-by: Sibi Sankar <sibi.sankar@oss.qualcomm.com>
Co-developed-by: Jyothi Kumar Seerapu <jyothi.seerapu@oss.qualcomm.com>
Signed-off-by: Jyothi Kumar Seerapu <jyothi.seerapu@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Pankaj Patil <pankaj.patil@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260219-upstream_v3_glymur_introduction-v8-4-8ce4e489ebb6@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
All the Lemans IOT variants boards are using Gunyah hypervisor which
means that, so far, Linux-based OS could only boot in EL1 on those
devices. However, it is possible for us to boot Linux at EL2 on these
devices [1].
When running under Gunyah, the remote processor firmware IOMMU streams
are controlled by Gunyah. However, without Gunyah, the IOMMU is managed
by the consumer of this DeviceTree. Therefore, describe the firmware
streams for each remote processor.
Add a EL2-specific DT overlay and apply it to Lemans IOT variant
devices to create -el2.dtb for each of them alongside "normal" dtb.
[1]
https://docs.qualcomm.com/bundle/publicresource/topics/80-70020-4/boot-developer-touchpoints.html#uefi
Signed-off-by: Mukesh Ojha <mukesh.ojha@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260105-kvmrprocv10-v10-14-022e96815380@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
This initial version includes support for OV9282 camera sensor.
Signed-off-by: Loic Poulain <loic.poulain@oss.qualcomm.com>
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Link: https://lore.kernel.org/r/20260108170550.359968-4-loic.poulain@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add a devicetree for The Fairphone (Gen. 6) smartphone, which is based
on the Milos/SM7635 SoC.
Supported functionality as of this initial submission:
* Debug UART
* Regulators (PM7550, PM8550VS, PMR735B, PM8008)
* Remoteprocs (ADSP, CDSP, MPSS, WPSS)
* Power Button, Volume Keys, Switch
* PMIC-GLINK (Charger, Fuel gauge, USB-C mode switching)
* Camera flash/torch LED
* SD card
* USB
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251210-sm7635-fp6-initial-v4-9-b05fddd8b45c@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
This adds initial device tree support for the following phones:
- Google Pixel 3 (blueline)
- Google Pixel 3 XL (crosshatch)
Both phone boards use the same identifiers and differ only slightly
in their connected peripherals.
Supported functionality includes:
- Debug UART
- UFS
- USB-C (peripheral mode)
- Framebuffer (both u-boot and Linux)
- Display (Pixel 3 only, and the driver needs work)
- GPU
- Bluetooth
- Wi-Fi
The rmtfs region is allocated using UIO, making it technically "dynamic."
Its address and size can be read from sysfs:
$ cat /sys/class/uio/uio0/name
/sys/class/uio/uio0/maps/map0/addr
0x00000000f2701000
$ cat /sys/class/uio/uio0/maps/map0/size
0x0000000000200000
Like the OnePlus 6, the Pixel 3 requires 1 kB of reserved memory on either
side of the rmtfs region to work around an XPU bug that would otherwise
cause erroneous violations when accessing the rmtfs_mem region.
Co-developed-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Co-developed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Co-developed-by: Casey Connolly <casey@connolly.tech>
Signed-off-by: Casey Connolly <casey@connolly.tech>
Co-developed-by: Joel Selvaraj <foss@joelselvaraj.com>
Signed-off-by: Joel Selvaraj <foss@joelselvaraj.com>
Co-developed-by: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Co-developed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: David Heidelberg <david@ixit.cz>
Link: https://lore.kernel.org/r/20251214-pixel-3-v7-8-b1c0cf6f224d@ixit.cz
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add device trees for the Qualcomm X1E and X1P-based Microsoft Surface
Pro 11 machines (codenamed 'Denali').
This device is very similar to the Surface Laptop 7 ('Romulus').
Use a similar strategy to x1-asus-zenbook-a14.dtsi so that we can create
x1e and x1p-specific flavors of the device tree without too much code
duplication.
Hardware support is similar to other X1 machines. The most notable
missing features are:
- Touchscreen and pen
- Cameras (and status LEDs)
Signed-off-by: Dale Whinham <daleyo@gmail.com>
Signed-off-by: Jérôme de Bretagne <jerome.debretagne@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251220-surface-sp11-for-next-v6-4-81f7451edb77@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
To provide access to camera sensors a Rear Camera Card can be connected
to SM8650-HDK board, the camera sensors are:
* Samsung S5K33D ToF camera sensor, connected to CSI0 over MIPI D-PHY,
* Sony IMX766 Wide camera sensor, connected to CSI1 over MIPI C-PHY,
* Omnivision OV64B Ultrawide camera sensor, connected to CSI2 over MIPI C-PHY,
* Samsung S5KJN1 Tele camera sensor, connected to CSI3 over MIPI D-PHY).
Get the initial support of Samsung S5KJN1 camera sensor and two flash leds
on the Rear Camera Card board by adding a board overlay.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Link: https://lore.kernel.org/r/20251204041505.131891-5-vladimir.zapolskiy@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add initial support for Qualcomm Kaanapali QRD board which enables
SD Card, UFS and booting to shell with UART console.
Written with help from Jishnu Prakash (added RPMhPD nodes), Nitin Rawat
(added ufs) and Manish Pandey (added SD Card).
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Jingyi Wang <jingyi.wang@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251215-knp-dts-v4-5-1541bebeb89f@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add initial support for Qualcomm Kaanapali MTP board which enables PCIe,
SD Card, UFS and booting to shell with UART console.
Written with help from Jishnu Prakash (added RPMhPD nodes), Nitin Rawat
(added UFS), Manish Pandey (added SD Card) and Qiang Yu (added PCIe).
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Jingyi Wang <jingyi.wang@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251215-knp-dts-v4-4-1541bebeb89f@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Lantronix SM8550-HDK board may be equipped with a Rear Camera Card PCB
which contains:
* Samsung S3K33D time-of-fligt image sensor connected to CSIPHY0 (TOF),
* Omnivision OV64B40 image sensor connected to CSIPHY1 (uWide),
* Sony IMX766 image sensor connected to CSIPHY2 (Wide),
* Samsung S5K3M5 image sensor connected to CSIPHY3 (Tele),
* two flash leds.
The change adds support of a Samsung S5K3M5 camera image sensor and
two flash leds on the external camera card module.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20251013235500.1883847-4-vladimir.zapolskiy@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add device tree for Huawei MateBook E 2019, which is a 2-in-1 tablet based
on Qualcomm's sdm850 platform.
Supported features:
- ADSP, CDSP and SLPI
- Volume Key
- Power Key
- Tablet Mode Switching
- Display
- Touchscreen
- Stylus
- WiFi [1]
- Bluetooth [2]
- GPU
- USB
- Keyboard
- Touchpad
- UFS
- SD Card
- Audio (right internal mic and headphone mic not working)
- Mobile Network
[1] WiFi probing log:
ath10k_snoc 18800000.wifi: Adding to iommu group 12
ath10k_snoc 18800000.wifi: qmi chip_id 0x30214 chip_family 0x4001 board_id 0xff soc_id 0x40030001
ath10k_snoc 18800000.wifi: qmi fw_version 0x2009856b fw_build_timestamp 2018-07-19 12:28 fw_build_id QC_IMAGE_VERSION_STRING=WLAN.HL.2.0-01387-QCAHLSWMTPLZ-1
ath10k_snoc 18800000.wifi: wcn3990 hw1.0 target 0x00000008 chip_id 0x00000000 sub 0000:0000
ath10k_snoc 18800000.wifi: kconfig debug 1 debugfs 1 tracing 1 dfs 0 testmode 0
ath10k_snoc 18800000.wifi: firmware ver api 5 features wowlan,mgmt-tx-by-reference,non-bmi crc32 b3d4b790
ath10k_snoc 18800000.wifi: htt-ver 3.53 wmi-op 4 htt-op 3 cal file max-sta 32 raw 0 hwcrypto 1
ath10k_snoc 18800000.wifi: invalid MAC address; choosing random
[2] Bluetooth probing log:
Bluetooth: hci0: setting up wcn399x
Bluetooth: hci0: QCA Product ID :0x0000000a
Bluetooth: hci0: QCA SOC Version :0x40010214
Bluetooth: hci0: QCA ROM Version :0x00000201
Bluetooth: hci0: QCA Patch Version:0x00000001
Bluetooth: hci0: QCA controller version 0x02140201
Bluetooth: hci0: QCA Downloading qca/crbtfw21.tlv
Bluetooth: hci0: QCA Downloading qca/crnv21.bin
Bluetooth: hci0: QCA setup on UART is completed
Features not supported yet:
- Panel Backlight
- Lid Detection
- Battery
- EFI Variable Access
- Cameras
1. Panel backlight, lid detection and battery will be supported with the
EC driver upstreamed.
2. EFI variables can only be read with the QSEECOM driver, and will be
enabled when the driver is fixed.
3. Cameras are tested to work with modified downstream driver, and once
drivers for these camera modules are included in the tree, cameras can
be enabled.
Features won't be supported:
- External Display
- Fingerprint
1. To make external display work, more reverse engineering may be required,
but it's beyond my ability.
2. Fingerprint is controlled by TrustZone, meaning direct access to it
isn't possible.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Jingzhou Zhu <newwheatzjz@zohomail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251008130052.11427-3-newwheatzjz@zohomail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Radxa Dragon Q6A is a single board computer, based on the Qualcomm
QCS6490 platform.
Features enabled and working:
- Configurable I2C/SPI/UART from 40-Pin GPIO
- Three USB-A 2.0 ports
- RTL8111K Ethernet connected to PCIe0
- eMMC module
- SD card
- M.2 M-Key 2230 PCIe 3.0 x2
- Headphone jack
- Onboard thermal sensors
- QSPI controller for updating boot firmware
- ADSP remoteproc (Type-C and charging features disabled in firmware)
- CDSP remoteproc (for AI applications using QNN)
- Venus video encode and decode accelerator
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Xilin Wu <sophon@radxa.com>
Link: https://lore.kernel.org/r/20250929-radxa-dragon-q6a-v5-2-aa96ffc352f8@radxa.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The laptop comes in two variants:
* UX3407RA, higher end, FHD+ OLED or WOXGA+ OLED panels
* UX3407QA, lower end, FHD+ OLED or FHD+ LCD panels
Even though all three panels work with "edp-panel", unfortunately the
brightness adjustmenet of LCD panel is PWM based, requiring a dedicated
device-tree. Convert "x1p42100-asus-zenbook-a14.dts" into ".dtsi" to
allow for this split, introduce new LCD variant. Leave current variant
without postfix and with the unchanged model name, as some distros
(eg. Ubuntu) rely on this for automatic device-tree detection during
kernel installation/upgrade.
As dedicated device-tree is required, update compatibles of OLED
variants to correct ones. Keep "edp-panel" as fallback, since it is
enough to make the panels work.
While at it moving .dts, .dtsi around, drop 'model' from the top level
x1-asus-zenbook-a14.dtsi as well.
Co-developed-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
Signed-off-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Aleksandrs Vinarskis <alex@vinarskis.com>
Link: https://lore.kernel.org/r/20250927-zenbook-improvements-v3-2-d46c7368dc70@vinarskis.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The HAMOA-IOT-EVK is an evaluation platform for IoT products, composed of
the Hamoa IoT SoM and a carrier board. Together, they form a complete
embedded system capable of booting to UART.
Make the following peripherals on the carrier board enabled:
- UART
- On-board regulators
- USB Type-C mux
- Pinctrl
- Embedded USB (EUSB) repeaters
- NVMe
- pmic-glink
- USB DisplayPorts
- Bluetooth
- WLAN
- Audio
Written in collaboration with Quill Qi (Audio) <le.qi@oss.qualcomm.com>,
Jie Zhang (Graphics) <quic_jiezh@quicinc.com>, Shuai Zhang (Bluetooth)
<quic_shuaz@quicinc.com>, Yingying Tang (WLAN) <quic_yintang@quicinc.com>,
and Yongxing Mou (USB DisplayPorts) <quic_yongmou@quicinc.com>.
Signed-off-by: Yijie Yang <yijie.yang@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250917-hamoa_initial-v12-3-4ed39d17dfc5@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Enable IMX577 via CCI1 on LeMans EVK Core Kit.
The LeMans EVK board does not include a camera sensor
by default, this overlay reflects the possibility of
attaching an optional camera sensor.
For this reason, the camera sensor configuration is
placed in lemans-evk-camera.dtso, rather than
modifying the base lemans-evk.dts.
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Wenmeng Liu <quic_wenmliu@qualcomm.com>
Link: https://lore.kernel.org/r/20250912-camss_rb8-v6-3-c9a6c3d67392@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add new device support for the Samsung Galaxy S22 (SM-S901E) phone
What works:
- SimpleFB
- USB
Signed-off-by: Eric Gonçalves <ghatto404@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250912202603.7312-2-ghatto404@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
These laptops are the same as the already known 14-fe0xxx models, but
with a Purwa SoC, SKU number 14-fe1xxx. [1]
The supported features are the same as for the original Omnibook X14:
- Keyboard (no function keys though)
- Display
- PWM brightness control
- Touchpad
- Touchscreen
- PCIe ports (pcie4, pcie6a)
- USB type-c, type-a
- WCN6855 Wifi-6E
- WCN6855 Bluetooth
- ADSP and CDSP
- X1 GPU
- GPIO Keys (Lid switch)
- Audio definition (works via USB and with internal speakers)
[1]: https://www.hp.com/us-en/shop/pdp/hp-omnibook-x-laptop-next-gen-ai-pc-14-fe100-14-a4nd1av-1#techSpecs
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
Link: https://lore.kernel.org/r/20250915-hp-x14-x1p-v9-3-fa457ca30ffe@oldschoolsolutions.biz
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
