Rename node name display@0 to display0 since no reg under it. Rename mode0
to timing0.
Fix below CHECK_DTBS warnings:
arch/arm/boot/dts/nxp/ls/ls1021a-iot.dtb: dcu@2ce0000 (fsl,ls1021a-dcu): 'display', 'display@0' do not match any of the regexes: '^pinctrl-[0-9]+$'
from schema $id: http://devicetree.org/schemas/display/fsl,ls1021a-dcu.yaml
arch/arm/boot/dts/nxp/ls/ls1021a-iot.dtb: display-timings: 'mode0' does not match any of the regexes: '^pinctrl-[0-9]+$', '^timing'
from schema $id: http://devicetree.org/schemas/display/panel/display-timings.yaml
Signed-off-by: Frank Li <Frank.Li@nxp.com>
The nand-ecc-strength and nand-ecc-step-size is bigger than 0. It doesn't
make sense to set to 0.
Remove it to fix below DTB_CHECKS warnings:
arch/arm/boot/dts/nxp/imx/imx6ull-engicam-microgea-bmm.dtb: nand-controller@1806000 (fsl,imx6q-gpmi-nand): nand-ecc-strength: 0 is less than the minimum of 1
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Remove undocument property clock-names of fsl,sgtl5000 to fix below
CHECK_DTBS warnings:
arch/arm/boot/dts/nxp/imx/imx6ul-isiot-nand.dtb: codec@a (fsl,sgtl5000): Unevaluated properties are not allowed ('clock-names' was unexpected)
from schema $id: http://devicetree.org/schemas/sound/fsl,sgtl5000.yaml
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Remove undocument properties ovti,ov5642 to fix below CHECK_DTBS warnings:
arch/arm/boot/dts/nxp/imx/imx53-smd.dtb: ov5642@3c (ovti,ov5642): 'clock-names' does not match any of the regexes: '^pinctrl-[0-9]+$'
from schema $id: http://devicetree.org/schemas/media/i2c/ovti,ov5642.yaml
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Change #io-channel-cells to 1 of voltage divider to fix below CHENCK_DTBS
warnings:
arch/arm/boot/dts/nxp/imx/imx6dl-plym2m.dtb: voltage-divider-vaccu (voltage-divider): #io-channel-cells: 1 was expected
from schema $id: http://devicetree.org/schemas/iio/afe/voltage-divider.yaml
Signed-off-by: Frank Li <Frank.Li@nxp.com>
default-state = "on" is wrong copied from gpio-leds nodes. Remove it to fix
below CHECK_DTBS warnings:
arch/arm/boot/dts/nxp/ls/ls1021a-moxa-uc-8410a.dtb: gpio-keys (gpio-keys): pushbtn-key: Unevaluated properties are not allowed ('default-state' was unexpected)
from schema $id: http://devicetree.org/schemas/input/gpio-keys.yaml
Signed-off-by: Frank Li <Frank.Li@nxp.com>
spansion,s25fl164k (drivers/mtd/spi-nor/spansion.c) can be identified with
the READ ID opcode (0x9F).
Replace spansion,s25fl164k with jedec,spi-nor to fix below CHECK_DTBS
warnings:
arch/arm/boot/dts/nxp/ls/ls1021a-moxa-uc-8410a.dtb: /soc/spi@1550000/flash@0: failed to match any schema with compatible: ['spansion,s25fl064l', 'spansion,s25fl164k']
So no other known DTB user this dts file and it is fine to broken potential
back compatibility since spansion,s25fl164k already support by use
jedec,spi-nor since 2015 commit 413780d7d7 ("mtd: spi-nor: Add support
for Spansion S25FL164K")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Replace marvell,88e1118 with ethernet-phy-ieee802.3-c22.
In drivers/net/mdio/of_mdio.c
/* The following is a list of PHY compatible strings which appear in
* some DTBs. The compatible string is never matched against a PHY
* driver, so is pointless. We only expect devices which are not PHYs
* to have a compatible string, so they can be matched to an MDIO
* driver. Encourage users to upgrade their DT blobs to remove these.
*/
static const struct of_device_id whitelist_phys[]
Fix below CHECK_DTBS warnings:
arch/arm/boot/dts/nxp/ls/ls1021a-moxa-uc-8410a.dtb: /soc/mdio@2d24000/ethernet-phy@0: failed to match any schema with compatible: ['marvell,88e1118']
No other known DTB user this dts file.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add power-supply for lcd panel to fix below CHECK_DTBS warnings:
arch/arm/boot/dts/nxp/ls/ls1021a-twr.dtb: panel (nec,nl4827hc19-05b): 'power-supply' is a required property
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add led suffix to fix below CHECK_DTBS warnings:
ls1021a-moxa-uc-8410a.dtb: leds (gpio-leds): 'beeper', ... do not match
any of the regexes: '(^led-[0-9a-f]$|led)', '^pinctrl-[0-9]+$'
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Change node name eim-cs1 to eim-cs1-bus to fix below CHECK_DTS warnings:
arch/arm/boot/dts/nxp/imx/imx53-ard.dtb: eim-cs1@f4000000 (fsl,eim-bus): $nodename:0: 'eim-cs1@f4000000' does not match '^([a-z][a-z0-9\\-]+-bus|bus|localbus|soc|axi|ahb|apb)(@.+)?$'
from schema $id: http://devicetree.org/schemas/simple-bus.yaml
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add front compatible string "fsl,ls1021aqds-fpga" for on boards FPGA chip
and remove unused property bank-width and device-width, which used for
MTD devices and FPGA is not a MTD devices.
Fix below CHECK_DTBS warning:
rch/arm/boot/dts/nxp/ls/ls1021a-qds.dtb: memory-controller@1530000 (fsl,ifc): board-control@3,0: 'oneOf' conditional failed, one must be fixed:
'bank-width', 'device-width' do not match any of the regexes: '^gpio@[0-9a-f]+$', '^mdio-mux@[a-f0-9,]+$', '^pinctrl-[0-9]+$'
/home/lizhi/source/linux-upstream-pci-ep-arm/arch/arm/boot/dts/nxp/ls/ls1021a-qds.dtb: memory-controller@1530000 (fsl,ifc): board-control@3,0:compatible: 'oneOf' conditional failed, one must be fixed:
['simple-mfd'] is too short
arch/arm/boot/dts/nxp/ls/ls1021a-qds.dtb: memory-controller@1530000 (fsl,ifc): board-control@3,0: Unevaluated properties are not allowed ('#address-cells', '#size-cells', 'bank-width', 'compatible', 'device-width', 'mdio-mux@54', 'ranges', 'reg' were unexpected)
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
TQMa6x has board-information located in EEPROM at offset 0x20.
Add necessary nodes and properties for nvmem cell.
Signed-off-by: Max Merchel <Max.Merchel@ew.tq-group.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
TQMa6UL has board-information located in EEPROM at offset 0x20.
Add necessary nodes and properties for nvmem cell.
Signed-off-by: Max Merchel <Max.Merchel@ew.tq-group.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add the power supply property to the Root Port child node to support the
new PCI pwrctrl framework.
Legacy power supply property is retained for backward compatibility with
existing kernels. New device trees should specify power supply at the
Root Port level to utilize the pwrctrl framework.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add the power supply property to the Root Port child node to support the
new PCI pwrctrl framework.
Legacy power supply property is retained for backward compatibility with
existing kernels. New device trees should specify power supply at the
Root Port level to utilize the pwrctrl framework.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Correct spaces or mix of tabs+spaces into proper tab-indented lines.
No functional impact (same DTB).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Ampak AP6335i Wi-Fi module atop i.MX7D Pico SoM also supports Bluetooth 4.1
via UART attached to "serial6" port. Describe it, so the controller can
probe automatically on boot.
This is based on "Pico i.MMX Development Kit for Android Things Hardware
Manual" rev. B1 [1], Table 6 on page 12.
Link: https://www.nxp.com/docs/en/user-guide/PICO-IMX7UL-USG.pdf [1]
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add the bootph-all property to ULP watchdog nodes for i.MX7ULP, ensuring
the watchdog is available during all boot phases.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
TQMa7 has board-information located in EEPROM at offset 0x20.
Add necessary nodes and properties for nvmem cell.
Signed-off-by: Alexander Feilke <Alexander.Feilke@ew.tq-group.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add OV5645 camera device node and enable relevant components in the
video capture data path, so output stream can be captured, and the
camera itself can be controlled over I2C bus.
This is roughly based on descriptions found in downstream kernel tree [1],
adapted to match upstream bindings.
Link: ce8fd74abf/arch/arm/boot/dts/imx7d-pico.dtsi (L874) [1]
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Replace the vendor-specific PHY compatible string with the generic
ethernet-phy-ieee802.3-c22 compatible.
The marvell,88E1510 compatible is listed in whitelist_phys[] and is
never matched against a PHY driver. PHY devices are expected to use
the generic ethernet-phy-ieee802.3-c22 compatible unless a specific
MDIO driver match is required.
The 88E1510 is compatible with Clause 22 PHY devices, so use the
generic compatible string instead.
Fix below CHECK_DTBS warnings:
arch/arm/boot/dts/nxp/imx/imx6q-display5-tianma-tm070-1280x768.dtb: /soc/bus@2100000/ethernet@2188000/mdio/ethernet-phy@0: failed to match any schema with compatible: ['marvell,88E1510']
Known other user (uboot) did not use marvell,88E1510.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
The edt,edt-ft5x06 compatible is not referenced in
drivers/input/touchscreen/edt-ft5x06.c and is not documented.
There is no publicly available datasheet or binding information that
distinguishes edt-ft5206/ft5306/ft5406 variants and the driver treats these
FT5x06-family controllers with the same configuration model. So switch to
the lowest common and documented baseline compatible edt,edt-ft5206.
Fix below CHECK_DTBS warnings:
arch/arm/boot/dts/nxp/imx/imx53-m53menlo.dtb: /soc/bus@60000000/i2c@63fc8000/touchscreen@38: failed to match any schema with compatible: ['edt,edt-ft5x06']
ABI impact consideration:
Not affect Linux kernel. The I2C subsystem uses a legacy fallback mechanism
where it strips the vendor prefix from the compatible string to derive the
client name, resulting in edt-ft5x06
{ .name = "edt-ft5x06", .driver_data = (long)&edt_ft5x06_data },
After this, the driver was actively binding to these devices based on the
compatible string.
Known user (U-Boot) does not parse or use edt,edt-ft* touchscreen
compatibles.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Remove the undocumented and unused compatible karo,imx6qdl-tx6-sgtl5000 and
retain only the generic simple-audio-card sound configuration.
The karo,imx6qdl-tx6-sgtl5000 compatible is not documented and is not
referenced by any in-kernel driver. The audio setup is already fully
described using simple-audio-card, which is the standard and supported
binding for this hardware configuration.
No known users (such as uboot) rely on karo,imx6qdl-tx6-sgtl5000.
Fix below CHECK_DTBS warnings:
arch/arm/boot/dts/nxp/imx/imx6dl-tx6dl-comtft.dtb: /sound: failed to match any schema with compatible: ['karo,imx6qdl-tx6-sgtl5000', 'simple-audio-card']
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add bus-type (MEDIA_BUS_TYPE_PARALLEL) for ov5642/ov5640. i.MX53 and
i.MX6UL only supports parallel csi interface. Fix below CHECK_DTBS
warnings:
arm/boot/dts/nxp/imx/imx53-smd.dtb: ov5642@3c (ovti,ov5642): port:endpoint: 'bus-type' is a required property
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Remove redundant bus-width property according to video-mux.yaml to fix
below CHECK_DTBS warnings:
arch/arm/boot/dts/nxp/imx/imx6dl-gw51xx.dtb: ipu1_csi0_mux (video-mux): port@4:endpoint: Unevaluated properties are not allowed ('bus-width' was unexpected)
from schema $id: http://devicetree.org/schemas/media/video-mux.yaml
The bus-width already set at remote endpoint (camera).
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add required power-supply and vdd-supply properties to fix below CHECK_DTB
warnings:
arch/arm/boot/dts/nxp/imx/imx53-m53menlo.dtb: panel (edt,etm0700g0dh6): 'power-supply' is a required property
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add '#phy-cells' for usb-nop-xceiv to fix below check_dtbs warnings:
usbphy-2 (usb-nop-xceiv): '#phy-cells' is a required property
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add dvdd and avdd supply and regulators for panel sii,43wvf1g to fix below
check_dtbs warnings:
panel (sii,43wvf1g): 'dvdd-supply' is a required property
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add required proprety ti,deskew for ti,tfp410, which have not defined
default value in yaml. 0 is default value according to
drivers/gpu/drm/bridge/ti-tfp410.c.
Fix below check_dtbs warning:
dvi-encoder (ti,tfp410): 'ti,deskew' is a required property
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Since describing the PCIe PERST# property under Host Bridge node is now
deprecated, it is recommended to add it to the Root Port node, so
creating the Root Port node and add the reset-gpios property in Root
Port.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Since describing the PCIe PERST# property under Host Bridge node is now
deprecated, it is recommended to add it to the Root Port node, so
creating the Root Port node and add the reset-gpios property in Root
Port.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Since describing the PCIe PERST# property under Host Bridge node is now
deprecated, it is recommended to add it to the Root Port node, so
creating the Root Port node and add the reset-gpios property in Root
Port.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
The Technologic Systems TS-4800 watchdog node was previously named 'wdt',
which violates the core watchdog.yaml schema expecting generic node names.
Rename the node to 'watchdog' to fix the following dtbs_check warning:
'wdt' does not match '^(pmic|timer|watchdog)(@.*|-([0-9]|[1-9][0-9]+))?$'
Signed-off-by: Eduard Bostina <egbostina@gmail.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add #io-channel-cells property to the ADC node. This property is required
for an IIO consumer driver to work.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
clock-names is empty in nand-controller@bb000000, which is wrong.
Remove it to fix below CHECK_DTBS warings:
arch/arm/boot/dts/nxp/imx/imx25-pdk.dtb: nand-controller@bb000000 (fsl,imx25-nand): Unevaluated properties are not allowed ('clock-names' was unexpected)
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
clock-names is empty in nand-controller@bb000000, which is wrong.
Remove it to fix below CHECK_DTBS warings:
arch/arm/boot/dts/nxp/imx/imx35-pdk.dtb: nand-controller@bb000000 (fsl,imx35-nand): Unevaluated properties are not allowed ('clock-names' was unexpected)
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add support for the LD configuration option (LVDS encoder assembled on SOM)
so that the LVDS display panel on the concerto EVK board works properly.
Not all VAR-SOM-6UL SOMs have the LD configuration option so factor out
this functionality to a separate dtsi.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Not all boards use the audio codec, so factor out this functionality to a
separate dtsi.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
ENET1 is currently disabled and not supported/working on the concerto EVK.
Add support for this optional configuration in a separate dtsi, so that it
can be selectively enabled/disabled.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Not all boards use the ethernet ENET2 port, so factor out this
functionality to a separate dtsi. On the concerto board, this
uses the ethernet PHY assembled on it.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add proper support for the optional Wifi and Bluetooth configuration on
VAR-SOM-6UL so that it works out of the box, without any custom scripts.
The Wifi/BT module support is mutually exclusive with SD card interface.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Move SD support to a separate dtsi, since it cannot be used at the
same time as the Wifi/BT module. Also not all boards support the SD card.
Move pinctrl_usdhc1* to the common imx6ul-var-som-common dtsi so that it
can be used by the future Wifi/BT dtsi.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
reorder pinctrl_gpio_leds to respect alphabetical order.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Export common parts to the Variscite VAR-SOM-6UL dtsi so that they can be
reused on other boards and to simplify adding future dedicated device tree
files for each CPU variant.
Move i2c1 pinctrl to var-som dtsi pinmux, so that it can be reused by other
boards.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Factor out the parts on the Variscite VAR-SOM-6UL [1] that are common to
all CPU variants (6UL, 6ULL, etc). This will simplify adding future
dedicated device tree files for each CPU variant.
Link https://dev.variscite.com/var-som-6ul [1]
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
There is no Variscite module named VAR-SOM-MX6UL, but there is VAR-SOM-MX6
and also VAR-SOM-6UL, so it is confusing at first to know to which one it
refers to. The imx6ul-var-som* dts/dtsi supports only the VAR-SOM-6UL [1],
not VAR-SOM-MX6 [2], so modify comments and model descriptions accordingly.
Link https://dev.variscite.com/var-som-6ul [1]
Link: https://dev.variscite.com/var-som-mx6 [2]
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
dmesg warning:
OF: /soc/bus@2000000/ethernet@20b4000/mdio/ethernet-phy@3: Read of
boolean property 'micrel,rmii-reference-clock-select-25-mhz' with a
value.
Using of_property_read_bool() for non-boolean properties is deprecated and
results in a warning during runtime since commit c141ecc3ce
("of: Warn when of_property_read_bool() is used on non-boolean properties")
micrel,rmii-reference-clock-select-25-mhz is a boolean property and should
not have a value, so remove it.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
The dc-supply property is non-existent in Linux now, nor when this DTS file
was created when importing it from Variscite own kernel.
Therefore remove it to fix this warning:
imx6ul-var-som-concerto.dtb: cpu@0 (arm,cortex-a7): Unevaluated
properties are not allowed ('dc-supply' was unexpected)
from schema $id: http://devicetree.org/schemas/arm/cpus.yaml
Fixes: 9d6a67d9c7 ("ARM: dts: imx6ul: Add Variscite VAR-SOM-MX6UL SoM support")
Cc: stable@kernel.org
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
