The Arduino Monza board has a TI INA232 current/power monitor connected
on I2C12 at address 0x40. It is used to measure the board supply current
through a 2 milliohms shunt resistor.
Signed-off-by: Loic Poulain <loic.poulain@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260611-monza-ina232-v2-3-e4375ce652d0@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The l12b and l15b supplies are used by components that are not (fully)
described (and some never will be) and must never be disabled.
Mark the regulators as always-on to prevent them from being disabled,
for example, when consumers probe defer or suspend.
Note that these supplies currently have no consumers described in
mainline for dell-thena beyond the audio codec (vdd-buck/vdd-rxtx/
vdd-io on wcd938x), which can release them when the codec goes idle.
The board-level gpio-fixed regulators that feed the Type-C retimer's
VDDIO and other rails are not described with a vin-supply link, so
the kernel cannot keep their parent LDOs alive on its own.
This mirrors the same change Johan Hovold applied to every other
X1E80100 board in a March 2025 series; commit 63169c07d7
("arm64: dts: qcom: x1e80100-dell-xps13-9345: mark l12b and l15b always-on")
is representative. The dell-thena board file was introduced four months
later and did not inherit that change; this patch closes the gap.
Fixes: e7733b4211 ("arm64: dts: qcom: Add support for Dell Inspiron 7441 / Latitude 7455")
Cc: stable@vger.kernel.org
Signed-off-by: Michael Scott <mike.scott@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Acked-by: Val Packett <val@packett.cool>
Link: https://lore.kernel.org/r/20260521010935.1333494-4-mike.scott@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The OPP table for the Iris core is wrong, it copies the VDD table from
the downstream kernel, but that table is written for the
video_cc_mvs0_clk_src, while the upstream uses video_cc_mvs0_clk for OPP
rate setting (which is clk_src divided by 3). Specify correct
frequencies in the OPP table.
Fixes: fa245b3f06 ("arm64: dts: qcom: sm8250: Add venus DT node")
Reported-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dikshita Agarwal <dikshita.agarwal@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Vishnu Reddy <busanna.reddy@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260604-iris-venus-fix-sm8250-v7-2-7bd2f0e5bae8@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add RX and TX clocks for the IPQ5018 GEPHY to enable the datapath.
Fixes: f5f2b835e3 ("arm64: dts: qcom: ipq5018: Add GE PHY to internal mdio bus")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://lore.kernel.org/r/20260608-ipq5018-gephy-clocks-v4-3-fb2ccd56894b@outlook.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Document the Sony Xperia M2, which is a smartphone based on the
Qualcomm MSM8926 SoC.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Erikas Bitovtas <xerikasxx@gmail.com>
Link: https://lore.kernel.org/r/20260610-yukon-eagle-v4-1-763d5698bd2c@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The correct CMN PLL reference clock rate for IPQ5018 is 4.8 GHz.
The CMN PLL driver did not account for the ref clock divider which is 2
for IPQ5018. Therefore, the computed rate was twice the actual output.
With the driver now accounting for the CMN PLL reference clock
divider (commit: 88c543fff7), set the correct reference clock rate.
Fixes: c006b249c5 ("arm64: dts: ipq5018: Add CMN PLL node")
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Acked-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260521-ipq5018-cmn-pll-rate-fix-v2-1-04b28a92e0f2@outlook.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
An error in dmesg shows there is a mismatch between controller and DT
dout-ports.
Add PCM_OUT port to fix this.
Signed-off-by: Esteban Urrutia <esteuwu@proton.me>
Link: https://lore.kernel.org/r/20260622-sm8450-qol-v1-4-37e2ee8df9da@proton.me
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Embedded Trace Router(ETR) is working as a DDR memory sink to collect
tracing data from source device and the CTCU device serves as the
control unit for the ETR device.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Jie Gan <jie.gan@oss.qualcomm.com>
Reviewed-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Acked-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20260204-enable-ctcu-and-etr-v3-3-0bb95c590ae1@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Embedded Trace Router(ETR) is working as a DDR memory sink to collect
tracing data from source device.
The CTCU serves as the control unit for the ETR device, managing its
behavior to determine how trace data is collected.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Jie Gan <jie.gan@oss.qualcomm.com>
Reviewed-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Acked-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20260204-enable-ctcu-and-etr-v3-2-0bb95c590ae1@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Document the platforms that fallback to using the qcom,sa8775p-ctcu
compatible for probing.
Signed-off-by: Jie Gan <jie.gan@oss.qualcomm.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Acked-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20260204-enable-ctcu-and-etr-v3-1-0bb95c590ae1@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The &pmh0101_gpios node is extended twice in glymur-crd.dtsi. The first
extension defines the nvme_reg_en pinctrl state for the NVMe regulator
enable GPIO (gpio14), and the second adds key_vol_up_default for the
volume-up key (gpio6).
Merge both pinctrl states into a single &pmh0101_gpios block to avoid
the duplicate node extension.
No functional change intended.
Fixes: a5ad8a8e47 ("arm64: dts: qcom: Commonize Glymur CRD DTSI")
Signed-off-by: Gopikrishna Garmidi <gopikrishna.garmidi@oss.qualcomm.com>
Reviewed-by: Pankaj Patil <pankaj.patil@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260602-merge-duplicate-pmh0101-gpios-node-v2-1-251107b3d9fe@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add support for camera clock controller for camera clients to
be able to request for camera clocks on Glymur SoC's.
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Jagadeesh Kona <jagadeesh.kona@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260624-glymur_camcc-v5-3-a321df74b1a1@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add DTS for the Vicharak Axon Mini board based on the Qualcomm
QCS6490 SoC.
This adds debug UART, eMMC, UFS, SDIO WLAN, USB 2.0 host, PCIe
support along with regulators.
The UFS ICE block is kept disabled because enabling it currently causes
an SError during qcom_ice_create() on this board. UFS works without ICE.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Ajit Singh <blfizzyy@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260624125443.18729-4-blfizzyy@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The Vicharak Axon Mini is a single-board computer based on the
Qualcomm QCM6490 platform.
Add the top-level compatible string for this board.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Ajit Singh <blfizzyy@gmail.com>
Link: https://lore.kernel.org/r/20260624125443.18729-3-blfizzyy@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Since each serial engine will be enabled as needed in each board dts,
there is no point of disabling the first QUPv3 wrapper in SoC dtsi.
So enable it by default. This is also now in line with the other SoCs, and
also with the second QUPv3 wrapper.
Fixes: 844807e1f8 ("arm64: dts: qcom: eliza: Add QUPv3, GPI DMA, SDHCI and LLCC nodes")
Signed-off-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260709-dts-qcom-eliza-enable-qupv3-1st-v1-1-e9a6904d0dea@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Describe the CPU and LLCC bandwidth monitor nodes for Eliza, together
with the corresponding OPP tables.
Signed-off-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260708-dts-qcom-eliza-add-bwmon-v1-1-602a409f550f@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Coding convention asks that equal character '=' in property assignment
is preceded and followed by a space.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260706-dts-qcom-style-checker-v2-4-90c781ae0417@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
DTS coding style prefers hyphens instead of underscores in the node
names. Change should be safe, because node names are not considered an
ABI.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260706-dts-qcom-style-checker-v2-1-90c781ae0417@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add device trees for the Shikra EVK platform, which combines each
of Shikra SoM variant with a common carrier board.
Three EVK boards are introduced:
- shikra-cqm-evk.dts: pairs with CQ2390M SoM (retail, with modem)
- shikra-cqs-evk.dts: pairs with CQ2390S SoM (retail, without modem)
- shikra-iqs-evk.dts: pairs with IQ2390S SoM (industrial, without modem)
Also add shikra-evk.dtsi, it represents the common carrier-board and
daughter-card configuration shared across all Shikra EVK variants.
Co-developed-by: Imran Shaik <imran.shaik@oss.qualcomm.com>
Signed-off-by: Imran Shaik <imran.shaik@oss.qualcomm.com>
Co-developed-by: Monish Chunara <quic_mchunara@quicinc.com>
Signed-off-by: Monish Chunara <quic_mchunara@quicinc.com>
Co-developed-by: Rakesh Kota <rakesh.kota@oss.qualcomm.com>
Signed-off-by: Rakesh Kota <rakesh.kota@oss.qualcomm.com>
Co-developed-by: Raviteja Laggyshetty <raviteja.laggyshetty@oss.qualcomm.com>
Signed-off-by: Raviteja Laggyshetty <raviteja.laggyshetty@oss.qualcomm.com>
Co-developed-by: Sneh Mankad <sneh.mankad@oss.qualcomm.com>
Signed-off-by: Sneh Mankad <sneh.mankad@oss.qualcomm.com>
Co-developed-by: Vishnu Santhosh <vishnu.santhosh@oss.qualcomm.com>
Signed-off-by: Vishnu Santhosh <vishnu.santhosh@oss.qualcomm.com>
Co-developed-by: Xueyao An <xueyao.an@oss.qualcomm.com>
Signed-off-by: Xueyao An <xueyao.an@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Komal Bajaj <komal.bajaj@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260612-shikra-dt-v6-5-6b6cb58db477@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add device tree include for the IQ2390S variant of the Shikra
System-on-Module, an industrial compute module integrating the Shikra
SoC and PMIC for industrial IoT applications, designed to mount on
carrier boards.
- shikra-iqs-som.dtsi: Industrial SoM without modem (PM8150 PMIC)
The DTSI includes the common shikra.dtsi and adds PM8150 PMIC regulator
definitions specific to this variant.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Komal Bajaj <komal.bajaj@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260612-shikra-dt-v6-4-6b6cb58db477@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add device tree include for the CQ2390M variant of the Shikra
System-on-Module, a compact compute module integrating the Shikra SoC
and PMIC for IoT applications, designed to mount on carrier boards.
- shikra-cqm-som.dtsi: Retail SoM with modem (PM4125 and PM8005 PMIC)
The DTSI includes the common shikra.dtsi, adds PM4125 and PM8005 PMIC
peripheral definitions specific to this variant. Since PM8005 regulators
are controlled by rpmpd, so disabling the pm8005 regulators.
Co-developed-by: Rakesh Kota <rakesh.kota@oss.qualcomm.com>
Signed-off-by: Rakesh Kota <rakesh.kota@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Komal Bajaj <komal.bajaj@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260612-shikra-dt-v6-3-6b6cb58db477@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Shikra is a Qualcomm IoT SoC available in a System-on-Module (SoM)
form factor. The SoM integrates the Shikra SoC, PMICs, and essential
passives, and is designed to be mounted on carrier boards.
Three eSoM variant are introduced:
- CQM: retail variant with integrated modem (PM4125 and PM8005 PMIC)
- CQS: retail variant without modem (PM4125 and PM8005 PMIC)
- IQS: industrial-grade variant without modem (PM8150 PMIC)
Each SoM variant pairs with a common EVK carrier board provides debug
UART, USB, and other peripheral interfaces.
Add compatible strings for the CQ2390M, CQ2390S, IQ2390S SoM variant and
its corresponding EVK boards.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Komal Bajaj <komal.bajaj@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260612-shikra-dt-v6-1-6b6cb58db477@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Document the X1E-80-100 variant of the HONOR MagicBook Art 14.
Signed-off-by: Konstantin Shabanov <mail@etehtsea.me>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20260629154812.9066-3-mail@etehtsea.me
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Both the CQS SoM and the MTP have the following array of PMICs:
PMK8550, PM7550, 2x PM8550VS, PMIV0102 and PMR735D.
Since on Eliza there is already support for SPMI multi-master,
it is necessary to duplicate the devicetree description for each
of these PMICs, due to the SPMI bus index and address.
So add a new Elize specific dtsi for each of these PMICs and include
all of them in both the CQS SoM and MTP board dts.
Signed-off-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260630-dts-qcom-eliza-mtp-evk-add-pmics-v1-1-f4f320f7c88b@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The Eliza CQS EVK board combines the CQ7790S-based (Eliza) SoM with the
common Eliza EVK base board, which provides connectors for different
peripherals.
Add a common Eliza EVK dtsi for the base board bits that can be reused
alongside other Eliza SoM variants. Then, add the final Eliza CQS EVK dts,
including the CQS SoM and common EVK dtsi.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260630-eliza-dts-qcs-evk-v4-3-18cbbdba6e7e@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The Eliza CQS (CQ7790S) System-on-Module is designed to be connected to
an Eliza EVK base board. The SoM provides the SoC, PMICs, LPDDR and eMMC,
while the EVK base board provides connectors for a multitude of
peripherals.
Add the Eliza CQS SoM DTSI so it can be included by the EVK board DTS.
Describe the regulators and board clocks, enable eMMC support through
SDHC1, specify the ADSP firmware and enable the ADSP remoteproc.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260630-eliza-dts-qcs-evk-v4-2-18cbbdba6e7e@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Document the compatible strings for the Qualcomm Eliza CQS
System-on-Module (SoM) and its EVK board.
The SoM is populated with a CQ7790S Eliza variant, PMICs, LPDDR and
eMMC. The SoM is then connected to the EVK base board, which provides
a multitude of connectors for peripherals.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260630-eliza-dts-qcs-evk-v4-1-18cbbdba6e7e@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Now that the predefined MCLK pinctrl configuration is available in the
sc8280xp SoC DTSI, switch the ThinkPad X13s to use it. Drop the local,
duplicate MCLK pin definition from the camera pinctrl node.
Signed-off-by: Pengyu Luo <mitltlatltl@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260629065905.15651-4-mitltlatltl@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Define pinctrl definitions to enable camera master clocks on sc8280xp.
Suggested-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Pengyu Luo <mitltlatltl@gmail.com>
Link: https://lore.kernel.org/r/20260629065905.15651-3-mitltlatltl@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The value can be retrieve via windbg on Windows.
lkd> !dd f111000 L8
ctl_reg => 0x284
in drivers/pinctrl/qcom/pinctrl-msm.c
function msm_gpio_dbg_show_one()
...
drive = (ctl_reg >> g->drv_bit) & 7; // (0x284 >> 6) & 7 == 2
...
seq_printf(s, " %dmA", msm_regval_to_drive(drive)); // (drive + 1) * 2 == 6;
...
So the value is 6, not 16, it matches Windows now.
Fixes: 21927e94ca ("arm64: dts: qcom: sc8280xp-x13s: Enable RGB sensor")
Signed-off-by: Pengyu Luo <mitltlatltl@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260629065905.15651-2-mitltlatltl@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Reserve memory region for audio PD dynamic loading and remote heap
requirements. Add the required VMID list for memory ownership
transfers.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Ekansh Gupta <ekansh.gupta@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260629-talos-remoteheap-v3-1-4e23366c9196@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add label properties to TPDM and CTI nodes in the glymur device tree to
provide human-readable identifiers for each CoreSight device. These
labels allow userspace tools and the CoreSight framework to identify
devices by name rather than by base address.
Signed-off-by: Jie Gan <jie.gan@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260624-add-label-node-for-glymur-v2-1-e8420fd7025f@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Update the 'enable-gpio' property name to 'enable-gpios' to conform to
the bindings for the TI DRV2604 haptics module. While at it, use the
GPIO_ACTIVE_HIGH define instead of the raw literal.
Fixes: 4ac46b3682 ("arm64: dts: qcom: msm8996: xiaomi-gemini: Add support for Xiaomi Mi 5")
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260625-topic-ti_drv2604_dtwarn-v1-1-76e91fcafbe8@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The lemans EVK has the PCIe M.2 Mechanical Key E connector to connect
wireless connectivity cards over PCIe and UART interfaces. Hence,
describe the connector node and link it with the PCIe 0 Root Port and
UART17 nodes through graph port/endpoint.
The M.2 Key E connector is powered by a 3.3V fixed regulator
(vreg_wcn_3p3) which is sourced from the board's 12V DC input rail
(vreg_dcin_12v). Both regulators are always-on and are required by the
pcie-m2-e-connector binding.
Also add the serial1 = &uart17 alias, which is required for the
Bluetooth serdev device to be enumerated on the UART17 interface.
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Wei Deng <wei.deng@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260622-v3-lemans-split-v3-2-d26bb22594e3@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add 'compatible = "pciclass,0604"' to the pcieport0 node in lemans.dtsi
to allow the PCI subsystem to associate the DT node with the PCI-to-PCI
bridge device. This is required for downstream DT nodes (such as M.2
connectors described as graph endpoints of the Root Port) to be matched
to PCI devices.
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Wei Deng <wei.deng@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260622-v3-lemans-split-v3-1-d26bb22594e3@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add device tree bindings for the camera clock controller on
Qualcomm Glymur SoC.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Jagadeesh Kona <jagadeesh.kona@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260624-glymur_camcc-v5-1-a321df74b1a1@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Introduce a passive polling delay to ensure more than one
"passive" thermal point is considered when throttling the GPU
thermal zone.
Signed-off-by: Haritha S K <haritha.k@oss.qualcomm.com>
Acked-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260505-qcs615_gpu_cooling-v2-1-1ba42260b29d@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Initial device tree for Microsoft Surface Pro 12in
Currently supported:
- UFS
- Touchscreen
- Pen
- USB 3.2 x2 (DP Alt Mode)
- Audio
- Wifi
- Bluetooth
- CDSP
- ADSP
- GPU
Not currently supported:
- Accelerometer
- Front, Back and IR cameras
- IRIS video decoder
Tested on Surface_Pro_12in_1st_Ed_with_Snapdragon_2110
Signed-off-by: Harrison Vanderbyl <harrison.vanderbyl@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260609145906.40854-2-harrison.vanderbyl@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
