When "snps,rx-queues-to-use" or "tx-queues-to-use" config in DTS is provided
current code will apply U8_MAX value for queues_to_use if there is input of
higher value. But actual maximum number of supported queues is set via
macro MTL_MAX_RX_QUEUES and MTL_MAX_TX_QUEUES, which currently have value of 8.
This value of U8_MAX will be capped to value provided by core in DMA
capabilities (dma_conf), but it does so only if core provides it.
This is true for XGMAC (dwxgmac2) and some GMAC (dwmac4),
but not for (dwmac1000). This capping is at later stage in stmmac_hw_init(),
and during stmmac_mtl_setup() we might parse fields outside allocated memory
if queues_to_use is over defines MTL_MAX_ values,
for example following rx_queues_cfg is array of size of MTL_MAX_RX_QUEUES.
Fix this by capping value to MTL_MAX during config parsing.
Reported-by: Sashiko <sashiko-bot@kernel.org>
Signed-off-by: Jakub Raczynski <j.raczynski@samsung.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260611113358.3379518-3-j.raczynski@samsung.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
While opening stmmac driver, there is enabling of TBS (Time-Based Scheduling)
option in dma config. Currently this is executed for all possible TX queues via
MTL_MAX_TX_QUEUES macro, but actual number of queues used might differ.
While setting this is generally harmless, since memory for MTL_MAX_TX_QUEUES
is allocated, it is incorrect, because it prepares config for unused queues.
Change this to apply tbs config only to tx_queues_to_use.
Co-developed-by: Chang-Sub Lee <cs0617.lee@samsung.com>
Signed-off-by: Chang-Sub Lee <cs0617.lee@samsung.com>
Signed-off-by: Jakub Raczynski <j.raczynski@samsung.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260611113358.3379518-2-j.raczynski@samsung.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In the context of a GDM port that can have multiple net_devices attached
(GDM3 and GDM4), the HW counters (MIBs) are global for the GDM port.
This cause duplicated stats reported to the kernel for the related
net_device.
The SoC supports a split MIB feature where each counter is tracked based
on the relevant HW channel (NBQ) to account for this scenario and
provide a way to select the related counter on accessing the MIB
registers.
Enable this feature for GDM3 and GDM4 and configure the relevant HW
channel before updating the HW stats to report correct HW counter to the
kernel for the related interface.
Move the stats struct from port to dev since HW counter are now specific
to the network device instead of the GDM port. Refactor
airoha_update_hw_stats() to take airoha_eth and airoha_gdm_port
parameters since the function operates on the entire port.
Co-developed-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260611-airoha-eth-multi-serdes-stats-v1-1-42442ae42064@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Convert lan9303.txt to yaml format to fix below CHECK_DTBS warnings:
arch/arm/boot/dts/nxp/imx/imx53-kp-hsc.dtb: /soc/bus@50000000/i2c@53fec000/switch@a: failed to match any schema with compatible: ['smsc,lan9303-i2c']
Additional changes:
- rename switch-phy to switch in example.
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260610150533.515914-1-Frank.Li@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To match how device-id array terminators look like for other device
types drop `.id = ""` from it and let the compiler care for zeroing the
entry.
There are no changes in the compiled drivers, only the source looks
nicer.
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/a0cd057e6a24b9d355b5e4bdfcdb812cdd1e4652.1781082923.git.u.kleine-koenig@baylibre.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce a new test, `ipv4_devconf_notify`, to verify that the kernel
sends the appropriate netlink notifications when IPv4 devconf parameters
are modified.
The test depends on the newly introduced iproute2 command:
`ip link set dev <ifname> inet`
Signed-off-by: Fernando Fernandez Mancera <fmancera@suse.de>
Link: https://patch.msgid.link/20260609204520.4670-3-fmancera@suse.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When IPv4 device configuration parameters are updated via netlink, the
kernel currently only updates the value. This bypasses several
post-modification actions that occur when these same parameters are
updated via sysctl, such as flushing the routing cache or emitting
RTM_NEWNETCONF notifications.
This patch addresses the inconsistency by calling the
devinet_conf_post_set() helper inside inet_set_link_af(). If a flush is
required, we defer it until the netlink attribute parsing loop
completes.
This ensures consistent behavior and side-effects for devconf changes,
regardless of whether they are initiated via sysctl or netlink.
Reviewed-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Fernando Fernandez Mancera <fmancera@suse.de>
Link: https://patch.msgid.link/20260609204520.4670-2-fmancera@suse.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The logic for handling IPv4 devconf sysctls is scattered. Notification
and cache flushes are managed in devinet_conf_proc(), while a separate
ipv4_doint_and_flush() function and DEVINET_SYSCTL_FLUSHING_ENTRY macro
is used for properties that solely require a cache flush.
This patch refactors the sysctl handling by introducing a centralized
helper, devinet_conf_post_set(). This new function evaluates the changed
attribute and handles all necessary operations like triggering netlink
notifications. It returns a boolean indicating whether a routing cache
flush is required.
Note that the boolean is necessary as this function will be re-used for
netlink IPv4 devconf handling where the cache flushing must wait until
all the attributes have been processed.
Finally, this is introducing a small change in behavior for
IPV4_DEVCONF_ROUTE_LOCALNET. As commit d0daebc3d6 ("ipv4: Add
interface option to enable routing of 127.0.0.0/8") intended, the cache
flush should only be performed when ROUTE_LOCALNET changes from 1 to 0.
Unfortunately, this was not true because while implementing it the
DEVINET_SYSCTL_FLUSHING_ENTRY was used for the attribute, making the
code related to it on devinet_conf_proc() dead.
IPV4_DEVCONF_FORWARDING is still being handled separately as it requires
more operations.
Reviewed-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Fernando Fernandez Mancera <fmancera@suse.de>
Link: https://patch.msgid.link/20260609204520.4670-1-fmancera@suse.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 0e24d17bd9 ("tcp: implement RFC 7323 window retraction
receiver requirements") removed the special FIN case that
was added in commit 1e3bb184e9 ("tcp: re-enable acceptance of
FIN packets when RWIN is 0").
If a peer sends a segment containing data and a FIN flag before
it learns about our window retraction and has a buggy TCP stack,
it might place the FIN one byte beyond what it thinks is the
right edge of the window (i.e., max_window_edge + 1).
The data portion (end_seq - th->fin) will end exactly at max_window_edge.
In this case, we will drop the packet if our receive queue is not empty,
even though the data was sent within the window we previously allowed.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@google.com>
Reviewed-by: Simon Baatz <gmbnomis@gmail.com>
Link: https://patch.msgid.link/20260608151452.706822-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Grzegorz Nitka says:
====================
dpll/ice: Add generic DPLL type and full TX reference clock control for E825
NOTE: This series is intentionally submitted on net-next (not
intel-wired-lan) as early feedback of DPLL subsystem changes is
welcomed. In the past possible approaches were discussed in [1].
This series adds TX reference clock support for E825 devices and exposes
TX clock selection and synchronization status via the Linux DPLL
subsystem.
Here is the high-level connection diagram for E825 device:
+------------------------------------------------------------------+
| |
| +-----------------------------+ |
| | | |
| | MAC | |
| |+------------+-----+ | |
| ||RX/1588 |PHC|tspll<----\ | |
+---+----+ ||MUX +---+-^---| | | |
| E | RX >---------------------> | >--\ | | |
| T | | /----------------> | >-\| | | |
| H |----+ | |+---------+----^---+ || | | |
| 1 | TX <----|----------------+TX MUX < OCXO | || | | |
| |PLL | | || |--------| || | | |
+---+----+ | /----+ <-ext_ref<-||-|----|------ext_ref
| E | RX >----/ | || |--------+ || | | |
| T | | | || < SyncE | || | | |
| H |----+ | |+-----------^------+ || | | |
| 2 | TX <----------------/ | | /------||-/ | |
| |PLL | +------------|-|------||------+ |
+---+----+ /--/ | || |
| . | RX >--- | | || |
| . | | +----------|----|------||--+ |
| . |----+ | +-^-+--^+ || | |
| | TX <--- | |EEC|PPS| || | |
| |PLL | | +-------+ || | |
+---+----+ | | <-CLK0/| | |
| E | RX >--- | | DPLL | | | |
| T | | | | <-CLK1-/ | |
| H |----+ | | | | |
| X | TX <--- | | <---SMA---< |
| |PLL | | | | | |
+---+----+ | | <---GPS---< |
| | | | | |
| | | <---...---< |
| | | | | |
| | +-------+ | |
| | External timing module | |
| +--------------------------+ |
+------------------------------------------------------------------+
E825 hardware contains a dedicated TX clock domain with per-port source
selection behavior that is distinct from PPS handling and from board-level
EEC distribution. TX reference clock selection is device-wide, shared
across ports, and mediated by firmware as part of link bring-up. As a
result, TX clock selection intent may differ from effective hardware
configuration, and software must verify outcome after link-up.
To support this, the series extends the DPLL core and the ice driver
incrementally. The series also introduces DPLL_TYPE_GENERIC as a broad
UAPI class for DPLL instances outside PPS/EEC categories. The intent is
to keep type naming reusable and scalable across different ASIC
topologies while preserving functional discoverability via
driver/device context and pin topology.
This follows netdev discussion guidance that UAPI type naming should avoid
location-specific or vendor-specific taxonomy, because such labels do not
scale across different ASIC designs. The function of a given DPLL instance
is already discoverable from driver/device context and pin topology, and
does not require an additional narrow type identifier in UAPI.
At the same time, a separate DPLL object is still needed for E825 TX clock
control/reporting semantics. Using DPLL_TYPE_GENERIC provides a reusable
class for devices outside PPS/EEC without overfitting UAPI naming to one
topology.
The relevant discussion is in [2].
Series content
- add a new generic DPLL type for devices outside PPS/EEC classes;
- relax DPLL pin registration rules for firmware-described shared pins
and extend pin notifications with a source identifier;
- allow dynamic state control of SyncE reference pins where hardware
supports it;
- add CPI infrastructure for PHY-side TX clock control on E825C;
- introduce a TX-clock DPLL device and TX reference clock pins
(EXT_EREF0 and SYNCE) in the ice driver;
- extend the Restart Auto-Negotiation command to carry a TX reference
clock index;
- implement hardware-backed TX reference clock switching, post-link
verification, and TX synchronization reporting.
TXCLK pins report TX reference topology only. Actual synchronization
success is reported via DPLL lock status, updated after hardware
verification: external TX references report LOCKED, while the internal
ENET/TXCO source reports UNLOCKED.
This provides reliable TX reference selection and observability on E825
devices using standard DPLL interfaces, without conflating user intent
with effective hardware behavior.
[1] https://lore.kernel.org/netdev/20250905160333.715c34ac@kernel.org/
[2] https://lore.kernel.org/netdev/20260402230626.3826719-1-grzegorz.nitka@intel.com/
====================
Link: https://patch.msgid.link/20260607183045.1213735-1-grzegorz.nitka@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Build on the previously introduced TXC DPLL framework and implement
full TX reference clock control and hardware-backed synchronization
status reporting for E825 devices.
E825 firmware may accept or override TX reference clock requests based
on device-wide routing constraints and link conditions. Because the
final selection becomes visible only after a link-up event, the driver
splits the observation into two complementary signals:
- TXCLK pin state reflects the requested TX reference clock
(pf->ptp.port.tx_clk_req). After a link-up, the value is reconciled
against the SERDES reference selector by
ice_txclk_update_and_notify(); if firmware or auto-negotiation
selected a different clock, tx_clk_req is overwritten so that pin
state converges to the actual hardware selection.
- TXC DPLL lock status reflects hardware synchronization:
* LOCKED when an external TX reference is in use
* UNLOCKED when falling back to ENET/TXCO, or when a requested
external reference has not (yet) been accepted by hardware.
Userspace observing only pin state therefore sees user intent, while
lock status is the authoritative indicator of whether the requested
clock is actually selected and synchronizing. This matches the DPLL
subsystem model where pin state describes topology and device lock
status describes signal quality.
TX reference selection topology:
- External references (SYNCE, EREF0) are represented as TXCLK pins
- The internal ENET/TXCO clock has no pin representation; when
selected, all TXCLK pins are reported DISCONNECTED
With this change, TX reference clocks on E825 devices can be reliably
selected, observed via standard DPLL interfaces, and monitored for
effective synchronization through TXC DPLL lock status.
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Link: https://patch.msgid.link/20260607183045.1213735-14-grzegorz.nitka@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Extend the Restart Auto-Negotiation (AN) AdminQ command with a new
parameter allowing software to specify the Tx reference clock index to
be used during link restart.
This patch:
- adds REFCLK field definitions to ice_aqc_restart_an
- updates ice_aq_set_link_restart_an() to take a new refclk parameter
and properly encode it into the command
- keeps legacy behavior by passing REFCLK_NOCHANGE where appropriate
This prepares the driver for configurations requiring dynamic selection
of the Tx reference clock as part of the AN flow.
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Link: https://patch.msgid.link/20260607183045.1213735-13-grzegorz.nitka@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add full CPI (Converged PHY Interface) command handling required for
E825C devices. The CPI interface allows the driver to interact with
PHY-side control logic through the LM/PHY command registers, including
enabling/disabling/selection of PHY reference clock.
This patch introduces:
- a new CPI subsystem (ice_cpi.c / ice_cpi.h) implementing the CPI
request/acknowledge state machine, including REQ/ACK protocol,
command execution, and response handling
- helper functions for reading/writing PHY registers over Sideband
Queue
- CPI command execution API (ice_cpi_exec) and a helper for enabling or
disabling Tx reference clocks (CPI 0xF1 opcode 'Config PHY clocking')
- assurance of CPI transaction serialization into the CPI core.
CPI REQ/ACK is a multi-step handshake and must be executed
atomically per PHY. Centralize the lock in ice_cpi_exec() and
use adapter-scoped per-PHY mutexes, which match the hardware sharing
model across PFs.
- addition of the non-posted write opcode (wr_np) to SBQ
- Makefile integration to build CPI support together with the PTP stack
This provides the infrastructure necessary to support PHY-side
configuration flows on E825C and is required for advanced link control
and Tx reference clock management.
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Link: https://patch.msgid.link/20260607183045.1213735-12-grzegorz.nitka@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
E825 devices provide a dedicated TX clock (TXC) domain which may be
driven by multiple reference clock sources, including external board
references and port-derived SyncE. To support future TX clock control
and observability through the Linux DPLL subsystem, introduce a
separate TXC DPLL device (of DPLL_TYPE_GENERIC) and a framework for
representing TX reference clock inputs.
This change adds a new internal DPLL pin type (TXCLK) and registers
TX reference clock pins for E825-based devices:
- EXT_EREF0: a board-level external electrical reference
- SYNCE: a port-derived SyncE reference described via firmware nodes
The TXC DPLL device is created and managed alongside the existing
PPS and EEC DPLL instances. TXCLK pins are registered directly or
deferred via a notifier when backed by fwnode-described pins.
A per-pin attribute encodes the TX reference source associated with
each TXCLK pin.
At this stage, TXCLK pin state callbacks and TXC DPLL lock status
reporting are implemented as placeholders. Pin state getters always
return DISCONNECTED, and the TXC DPLL is initialized in the UNLOCKED
state. No hardware configuration or TX reference switching is
performed yet.
This patch establishes the structural groundwork required for
hardware-backed TX reference selection, verification, and
synchronization status reporting, which will be implemented in
subsequent patches.
Also signal dpll_init from the fwnode pin init error path so any
notifier worker already blocked on it can drain, avoiding a
flush_workqueue() deadlock during teardown.
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Link: https://patch.msgid.link/20260607183045.1213735-11-grzegorz.nitka@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pins registered with an fwnode may have .state_on_dpll_set implemented
without advertising DPLL_PIN_CAPABILITIES_STATE_CAN_CHANGE upfront.
Requiring the bit for fwnode pins ties firmware description to driver
implementation details unnecessarily.
Relax the capability check in dpll_pin_state_set() and
dpll_pin_on_pin_state_set(): when a pin has an associated fwnode, bypass
the capability gate and let the ops layer decide, returning -EOPNOTSUPP
if .state_on_dpll_set is absent. Non-fwnode pins retain the original
strict behavior.
This is used later in the series by the SyncE_Ref output pin, which
relies on the fwnode path for state control.
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Link: https://patch.msgid.link/20260607183045.1213735-10-grzegorz.nitka@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Extend the DPLL pin notification API to include a source identifier
indicating where the notification originates. This allows notifier
consumers to distinguish between notifications coming from
an associated DPLL instance, a parent pin, or the pin itself.
A new field, src_clock_id, is added to struct dpll_pin_notifier_info
and is passed through all pin-related notification paths. Callers of
dpll_pin_notify() are updated to provide a meaningful source identifier
based on their context:
- pin registration/unregistration uses the DPLL's clock_id,
- pin-on-pin operations use the parent pin's clock_id,
- pin changes use the pin's own clock_id.
As introduced in the commit ("dpll: allow registering FW-identified pin
with a different DPLL"), it is possible to share the same physical pin
via firmware description (fwnode) with DPLL objects from different
kernel modules. This means that a given pin can be registered multiple
times.
Driver such as ICE (E825 devices) rely on this mechanism when listening
for the event where a shared-fwnode pin appears, while avoiding reacting
to events triggered by their own registration logic.
This change only extends the notification metadata and does not alter
existing semantics for drivers that do not use the new field.
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Link: https://patch.msgid.link/20260607183045.1213735-9-grzegorz.nitka@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
__dpll_pin_register() emits dpll_pin_create_ntf() internally, but
__dpll_pin_unregister() left the matching delete to its callers. The
counts then diverge on dpll_pin_on_pin_register() rollback and on
dpll_pin_on_pin_unregister(), leaking stale notifications.
Emit dpll_pin_delete_ntf() inside __dpll_pin_unregister() and drop the
now-redundant call in dpll_pin_unregister().
Fixes: 9431063ad3 ("dpll: core: Add DPLL framework base functions")
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Link: https://patch.msgid.link/20260607183045.1213735-8-grzegorz.nitka@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
__dpll_pin_unregister() wiped the global sync-pair state on every
(dpll, ops, priv, cookie) tuple removed from a pin. When a pin is
registered multiple times and only one registration is being torn
down, this dropped sync-pair pairings still in use by the surviving
registrations.
Move dpll_pin_ref_sync_pair_del() inside the xa_empty(&pin->dpll_refs)
branch so it only runs when the last registration is gone, alongside
clearing the DPLL_REGISTERED mark.
Fixes: 58256a26bf ("dpll: add reference sync get/set")
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Link: https://patch.msgid.link/20260607183045.1213735-7-grzegorz.nitka@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
dpll_pin_on_pin_register() emits a creation notification for every
parent->dpll_refs entry, but dpll_pin_on_pin_unregister() emitted only
one deletion notification outside the loop. When a pin is registered
against multiple parent dplls, userspace sees N creates but a single
delete and leaks per-dpll state.
Move dpll_pin_delete_ntf() into the loop and call it before
__dpll_pin_unregister() so the DPLL_REGISTERED mark is still set when
dpll_pin_available() is consulted.
Fixes: 9d71b54b65 ("dpll: netlink: Add DPLL framework base functions")
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Link: https://patch.msgid.link/20260607183045.1213735-6-grzegorz.nitka@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The rollback path in dpll_pin_on_pin_register() called
__dpll_pin_unregister() before dpll_pin_delete_ntf(). When the
unregister dropped the pin's last DPLL reference it cleared the
DPLL_REGISTERED mark in dpll_pin_xa, so the subsequent
dpll_pin_event_send() failed dpll_pin_available() and aborted with
-ENODEV. As a result userspace was never notified of the rollback
deletion and remained out of sync with the kernel.
Send the delete notification first, matching the order used by
dpll_pin_unregister() and dpll_pin_on_pin_unregister().
Fixes: 9d71b54b65 ("dpll: netlink: Add DPLL framework base functions")
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Link: https://patch.msgid.link/20260607183045.1213735-5-grzegorz.nitka@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Neither parent->dpll_refs nor pin->dpll_refs on its own is a correct
iteration target at unregister time:
- pin->dpll_refs includes DPLLs the child was registered against
via a different parent or directly; blind unregister WARNs on
the cookie miss in dpll_xa_ref_pin_del().
- parent->dpll_refs reflects the parent's current attachments, not
those at child-register time. Another driver may have (un)reg'd
the parent against additional DPLLs in the meantime, so we miss
registrations that exist and visit DPLLs that have none.
Walk pin->dpll_refs and use dpll_pin_registration_find() to filter
to entries whose cookie is this parent. Symmetric with
dpll_pin_on_pin_register(), correct under any subsequent change to
parent->dpll_refs.
Fixes: 9431063ad3 ("dpll: core: Add DPLL framework base functions")
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Link: https://patch.msgid.link/20260607183045.1213735-4-grzegorz.nitka@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Relax the (module, clock_id) equality requirement when registering a
pin identified by firmware (pin->fwnode). Some platforms associate a
FW-described pin with a DPLL instance that differs from the pin's
(module, clock_id) tuple. For such pins, permit registration without
requiring the strict match. Non-FW pins still require equality.
Keep netlink pin module reporting/filtering safe for this relaxed
registration model by caching the module name in the pin object at
allocation time and using the cached string in netlink paths.
This avoids dereferencing pin->module after provider module teardown.
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Link: https://patch.msgid.link/20260607183045.1213735-3-grzegorz.nitka@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add DPLL_TYPE_GENERIC to represent DPLL devices which do not fit the
existing PPS or EEC classes.
The UAPI type is intentionally generic. During netdev discussion,
maintainers pointed out that introducing identifiers tied to a specific
placement or single design does not scale across ASICs and vendors.
The role of a DPLL is already inferable from the spawning driver,
bus device, and pin topology, without encoding additional
purpose-specific taxonomy in the type name.
Using a generic type keeps the UAPI extensible and avoids premature
naming that may become incorrect as new hardware topologies are
exposed through the DPLL subsystem.
Expose the new type through UAPI and netlink specification as "generic".
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Link: https://patch.msgid.link/20260607183045.1213735-2-grzegorz.nitka@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=bils
-----END PGP SIGNATURE-----
Merge tag 'ipsec-next-2026-06-12' of git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec-next
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2026-06-12
1) Replace the open-coded manual cleanup in xfrm_add_policy() error
path with xfrm_policy_destroy() for consistency with
xfrm_policy_construct().
From Deepanshu Kartikey.
2) Limit XFRMA_TFCPAD to a sensible maximum (max IP length, 64k) since
u32 is excessive for traffic flow confidentiality padding.
From David Ahern.
3) Add a new netlink message XFRM_MSG_MIGRATE_STATE that
allows migrating individual IPsec SAs independently of
their policies. The existing XFRM_MSG_MIGRATE is tightly coupled
to policy+SA migration, lacks SPI for unique SA identification,
and cannot express reqid changes or migrate Transport mode
selectors. The new interface identifies the SA via SPI and mark,
supports reqid changes, address family changes, encap removal,
and uses an atomic create+install flow under x->lock to prevent
SN/IV reuse during AEAD SA migration.
From Antony Antony.
* tag 'ipsec-next-2026-06-12' of git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec-next:
xfrm: add documentation for XFRM_MSG_MIGRATE_STATE
xfrm: restrict netlink attributes for XFRM_MSG_MIGRATE_STATE
xfrm: add XFRM_MSG_MIGRATE_STATE for single SA migration
xfrm: make xfrm_dev_state_add xuo parameter const
xfrm: extract address family and selector validation helpers
xfrm: refactor XFRMA_MTIMER_THRESH validation into a helper
xfrm: move encap and xuo into struct xfrm_migrate
xfrm: add error messages to state migration
xfrm: add state synchronization after migration
xfrm: check family before comparing addresses in migrate
xfrm: split xfrm_state_migrate into create and install functions
xfrm: rename reqid in xfrm_migrate
xfrm: fix NAT-related field inheritance in SA migration
xfrm: allow migration from UDP encapsulated to non-encapsulated ESP
xfrm: add extack to xfrm_init_state
xfrm: remove redundant assignments
xfrm: Reject excessive values for XFRMA_TFCPAD
xfrm: cleanup error path in xfrm_add_policy()
====================
Link: https://patch.msgid.link/20260612074725.1760473-1-steffen.klassert@secunet.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Callers of vsock_remove_pending() must also call sk_acceptq_removed()
to keep sk_ack_backlog consistent. Move the call into
vsock_remove_pending() itself to make it automatic and prevent future
callers from forgetting it.
Suggested-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Raf Dickson <rafdog35@gmail.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Luigi Leonardi <leonardi@redhat.com>
Reviewed-by: Bobby Eshleman <bobbyeshleman@meta.com>
Link: https://patch.msgid.link/20260612045216.105796-5-rafdog35@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
virtio and hyperv call sk_acceptq_added() immediately before
vsock_enqueue_accept(). Move the call into vsock_enqueue_accept()
itself so callers cannot forget it and the accounting is consistent.
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Suggested-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Raf Dickson <rafdog35@gmail.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Luigi Leonardi <leonardi@redhat.com>
Reviewed-by: Bobby Eshleman <bobbyeshleman@meta.com>
Link: https://patch.msgid.link/20260612045216.105796-4-rafdog35@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move sk_acceptq_added() into vsock_add_pending() so callers cannot
forget it. vmci is the only transport using the pending list and
is updated accordingly.
Suggested-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Raf Dickson <rafdog35@gmail.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Luigi Leonardi <leonardi@redhat.com>
Reviewed-by: Bobby Eshleman <bobbyeshleman@meta.com>
Link: https://patch.msgid.link/20260612045216.105796-3-rafdog35@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add vsock_pending_to_accept() to move a socket directly from the
pending list to the accept queue in a single operation, avoiding
the sock_put/sock_hold dance and the sk_acceptq_removed()/
sk_acceptq_added() pair that would otherwise be needed when
calling vsock_remove_pending() followed by vsock_enqueue_accept().
Use it in vmci_transport_recv_connecting_server() where a completed
handshake transitions the socket from pending to accept queue.
Suggested-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Raf Dickson <rafdog35@gmail.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Luigi Leonardi <leonardi@redhat.com>
Reviewed-by: Bobby Eshleman <bobbyeshleman@meta.com>
Link: https://patch.msgid.link/20260612045216.105796-2-rafdog35@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace the open-coded backlog check with sk_acceptq_is_full().
The helper uses > instead of >=, which is the correct comparison
per commit 64a146513f ("[NET]: Revert incorrect accept queue
backlog changes."), and adds READ_ONCE() for proper memory ordering.
Suggested-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Raf Dickson <rafdog35@gmail.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Luigi Leonardi <leonardi@redhat.com>
Link: https://patch.msgid.link/20260612045842.122207-1-rafdog35@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Florian Westphal says:
====================
netdevsim: add fake FT/CLS_FLOWER offload
v2: fix up error reporting via extack
shellcheck cleanups
sort config toggles
1) Enable nf_tables offload control plane testing in netdevsim. Tag
existing offload fn to allow error injection for testing rollback and abort
logic.
2) Add nft_offload selftest to exercise the control plane and error
unwind via fault injection.
====================
Link: https://patch.msgid.link/20260612092209.11966-1-fw@strlen.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
... "phony", because its not testing offloads, it tests the control
plane code. Also test error unwind via fault injection framework.
For a proper test, real hardware would be required given we'd have
check if 'previously handed off to hardware' offload commands are
properly removed again on failure or rule flush.
Signed-off-by: Florian Westphal <fw@strlen.de>
Link: https://patch.msgid.link/20260612092209.11966-3-fw@strlen.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The actual 'offload' is phony, all commands are ignored: this is only
useful to test control plane code.
Tag the existing callback to permit error injection to test rollback/abort
code in nf_tables. This is also for fuzzers - the fault injection
framework allows probabilistic error insertion.
Signed-off-by: Florian Westphal <fw@strlen.de>
Link: https://patch.msgid.link/20260612092209.11966-2-fw@strlen.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Wei Wang says:
====================
psp: Add support for dev-assoc/disassoc
The main purpose of this feature is to associate virtual devices like
veth or netkit with a real PSP device, so we could provide PSP
functionality to the application running with virtual devices.
A typical deployment that works with this feature is as follows:
Host Namespace:
psp_dev_local ←──physically linked──→ psp_dev_peer
(PSP device)
│
│ BPF on psp_dev_local ingress: bpf_redirect_peer() to nk_guest
│
nk_host / veth_host
│
│ BPF on nk_host ingress: bpf_redirect_neigh() to psp_dev_local
│
Guest Namespace (netns):
│
nk_guest / veth_guest
★ PSP application run here
Remote Namespace (_netns):
psp_dev_peer
★ PSP server application runs here
Note:
The general requirement for this feature to work:
For PSP to work correctly, the egress device at validate_xmit_skb()
time must have psp_dev matching the association's psd. Any device
stacking or traffic redirection that changes the egress device will
cause either:
1. TX validation failure (SKB_DROP_REASON_PSP_OUTPUT) - fail-safe
2. RX policy failure after tx-assoc - packets without PSP extension
are rejected by receiver expecting encrypted traffic
Here are a few examples that this feature would not work:
- Bonding with load balancing in round-robin, XOR, 802.3ad mode across
multiple PSP devices, or mixed PSP and non-PSP devices
- Bonding with active-backup mode might work without PSP migration for
failover case.
- ipvlan/macvlan in bridge mode would not work given packets are
loopbacked locally without going through the PSP device.
====================
Link: https://patch.msgid.link/20260608233118.2694144-1-weibunny.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add the following 3 tests:
- _psp_dev_get_check_netkit_psp_assoc: verifies dev-get output in both
host and guest namespaces, checking assoc-list, by-association flag,
and nsid values
- _dev_assoc_no_nsid: tests dev-assoc and dev-disassoc without the nsid
attribute, verifying ifindex lookup in the caller's namespace
- _psp_dev_assoc_cleanup_on_netkit_del: verifies that deleting the
associated netkit interface properly cleans up the assoc-list, using
a disposable netkit pair to avoid disturbing the shared environment
Signed-off-by: Wei Wang <weibunny@fb.com>
Link: https://patch.msgid.link/20260608233118.2694144-11-weibunny.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add tests that verify PSP notifications are delivered to listeners in
associated namespaces:
- _key_rotation_notify_multi_ns_netkit: triggers key rotation and
verifies the notification is received in both main and guest namespaces
- _dev_change_notify_multi_ns_netkit: triggers dev_set and verifies the
dev_change notification is received in both namespaces
Signed-off-by: Wei Wang <weibunny@fb.com>
Link: https://patch.msgid.link/20260608233118.2694144-10-weibunny.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add _assoc_check_list() test that associates nk_guest with the PSP
device and verifies the assoc-list is correctly populated.
Add _data_basic_send_netkit_psp_assoc() which tests PSP data send
through a netkit interface associated with a PSP device. The test
associates nk_guest with the PSP device, then sends PSP-encrypted
traffic from the guest namespace.
Signed-off-by: Wei Wang <weibunny@fb.com>
Link: https://patch.msgid.link/20260608233118.2694144-9-weibunny.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add infrastructure to support PSP tests across network namespaces
using NetDrvContEnv with netkit pairs. This enables testing PSP device
association, where a non-PSP-capable device (e.g. netkit) in a guest
namespace is associated with a real PSP device in the host namespace,
allowing the guest to perform PSP encryption/decryption through the
host's PSP hardware.
The topology is:
Host NS: psp_dev_local <---> nk_host
| |
| | (netkit pair)
| |
Remote NS: psp_dev_peer Guest NS: nk_guest
(responder) (PSP tests)
env.py:
- nk_guest_ifindex is queried after moving the device into the guest
namespace, so tests can use it directly for dev-assoc
psp.py:
- PSP device lookup supports container environments where the PSP
device is on the physical interface, not the test interface
- Association helpers handle dev-assoc/dev-disassoc with defer-based
cleanup to prevent state leaks on test assertion failures
- main() tries NetDrvContEnv with primary_rx_redirect and falls back
to NetDrvEpEnv, so existing tests continue to work without the
container environment
Signed-off-by: Wei Wang <weibunny@fb.com>
Link: https://patch.msgid.link/20260608233118.2694144-8-weibunny.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rename _nk_host_ifname to nk_host_ifname in NetDrvContEnv to make it
a public attribute, matching the nk_guest_ifname rename. Tests that
access the host-side netkit interface name (e.g. for cleanup after
deleting the netkit pair) no longer trigger pylint protected-access
warnings.
Signed-off-by: Wei Wang <weibunny@fb.com>
Link: https://patch.msgid.link/20260608233118.2694144-7-weibunny.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add _find_bpf_obj() helper to NetDrvContEnv that searches the test
directory first, then falls back to the hw/ subdirectory. This allows
tests outside drivers/net/hw/ (e.g. psp.py in drivers/net/) to find
BPF objects built in the hw/ directory.
Update _attach_bpf() and _attach_primary_rx_redirect_bpf() to use
_find_bpf_obj() for BPF object discovery.
Signed-off-by: Wei Wang <weibunny@fb.com>
Link: https://patch.msgid.link/20260608233118.2694144-6-weibunny.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace the manual psp_ip_ver_test_builder() and ipver_test_builder()
functions with @ksft_variants decorators for data_basic_send and
data_mss_adjust. This is a pure refactor with no behavior change.
Signed-off-by: Wei Wang <weibunny@fb.com>
Link: https://patch.msgid.link/20260608233118.2694144-5-weibunny.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a new netdev event for dev unregister and handle the removal of this
dev from psp->assoc_dev_list, upon the first dev-assoc operation.
Signed-off-by: Wei Wang <weibunny@fb.com>
Reviewed-by: Daniel Zahka <daniel.zahka@gmail.com>
Link: https://patch.msgid.link/20260608233118.2694144-4-weibunny.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The main purpose of this cmd is to be able to associate a
non-psp-capable device (e.g. veth or netkit) with a psp device.
One use case is if we create a pair of veth/netkit, and assign 1 end
inside a netns, while leaving the other end within the default netns,
with a real PSP device, e.g. netdevsim or a physical PSP-capable NIC.
With this command, we could associate the veth/netkit inside the netns
with PSP device, so the virtual device could act as PSP-capable device
to initiate PSP connections, and performs PSP encryption/decryption on
the real PSP device.
Signed-off-by: Wei Wang <weibunny@fb.com>
Reviewed-by: Daniel Zahka <daniel.zahka@gmail.com>
Link: https://patch.msgid.link/20260608233118.2694144-3-weibunny.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce 2 versions of psp_device_get_locked:
1. psp_device_get_locked_admin(): This version is used for operations
that would change the status of the psd, and are currently used for
dev-set and key-rotation.
2. psp_device_get_locked(): This is the non-admin version, which are
used for broader user issued operations including: dev-get, rx-assoc,
tx-assoc, get-stats.
Following commit will be implementing both of the checks.
Signed-off-by: Wei Wang <weibunny@fb.com>
Reviewed-by: Daniel Zahka <daniel.zahka@gmail.com>
Link: https://patch.msgid.link/20260608233118.2694144-2-weibunny.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Bastien Curutchet says:
====================
net: dsa: microchip: remove unnecessary dsa_switch_ops callbacks
This series continues the rework of the KSZ driver initiated by two previous
series (see [1] & [2]).
The KSZ driver handles more than 20 switches split in several families.
This was previously handled through a common set of dsa_switch_ops
operations that used device-specific ksz_dev_ops callbacks. The two
previous series have split this common struct dsa_switch_ops into 5
to connect the ksz_dev_ops's implentations directly to the new
dsa_swicth ops.
This series continues in the same vein and removes the dsa_switch_ops
operations that aren't used.
On top of this on-going rework I added PTP and periodic output support for
the KSZ8463 (which was my first goal). There are still more than 20 patches
left for all this so this series will be followed by three others and if you
want to see the full picture we can check my github ([3]).
FYI, I only have a KSZ8463 so, unfortunately, I can't test other switches.
The next series is going to move out of ksz_common.c the last remaining
functions that aren't truly common to all KSZ switches. The series after
that will add PTP support for the KSZ8463 and the final one will add
periodic output support for the KSZ8463.
[1]: https://lore.kernel.org/r/20260505-clean-ksz-driver-v1-0-05d70fa42461@bootlin.com
[2]: https://lore.kernel.org/r/20260521-clean-ksz-2nd-series-v3-0-75c38971c19a@bootlin.com
[3]: https://github.com/bastien-curutchet/linux/tree/ksz_rework
====================
Link: https://patch.msgid.link/20260608-clean-ksz-3rd-v2-0-6e61b7be23c4@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The port_teardown() operation is optional. Yet, it is implemented by all
the KSZ switches through a common function that doesn't do anything for
the switches that aren't part of the ksz9477 family
Remove the implementation from the switches that don't need it.
Implement instead a ksz9477-specific port_teardown.
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260608-clean-ksz-3rd-v2-10-6e61b7be23c4@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All the switches use a common mdio_register() function that uses two
ksz_dev_ops callbacks (.mdio_bus_preinit() and .create_phy_addr_map())
to handle the lan937x specific case. These two callbacks are used only
at this place in the code.
Implement a new lan937x-specific MDIO registration functions that uses
these two lan937x-specific functions. The lan937x bindings don't
have any 'interrupts' property so this lan937x_mdio_register() doesn't
call ksz_irq_phy_setup().
Expose the common ksz_*_mdio_{read/write} functions so they can be used
in lan937x.c
Remove the callbacks from ksz_dev_ops.
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260608-clean-ksz-3rd-v2-9-6e61b7be23c4@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All switches implement the optional .port_hsr_join operation while only
the KSZ9477 truly supports it.
Remove the common port_hsr_join implementation.
Replace it with a specific implementation for the KSZ9477 case.
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260608-clean-ksz-3rd-v2-8-6e61b7be23c4@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All the KSZ switches use common {get/set}_wol operations while only the
ksz9477 and the ksz87xx families really support it. These operations are
optional so there is no point implementing them to return -EOPNOTSUPP.
Remove the {get/set}_wol callbacks from the switch operations for the
ksz88xx, the ksz8463 and the lan937x families.
Remove the family check from the common {get/set}_wol implementation.
Note that is_ksz9477() is only true for the KSZ9477 so this change will
also add WoL support for the other switches using the
ksz9477_switch_ops. I checked their datasheet, they implement the same
PME_WOL registers, at the same addresses, so this should go fine.
Modify the ksz_wol_pre_shutdown() initial check to ensure consistency in
the WoL handling for these non-KSZ9477 switches using ksz9477_switch_ops.
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260608-clean-ksz-3rd-v2-7-6e61b7be23c4@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The .support_eee() operation is optional. Yet, it is implemented by the
KSZ switches through a common functon that reports false for every chip
except for KSZ8563, KSZ9563 and KSZ9893 from the KSZ9477 family.
Remove the implementation from the switches that don't support EEE.
Also remove .set_mac_eee() for them as .set_mac_eee() is gated by the
`support_eee` presence in the core.
Implement instead a ksz9477-specific support_eee for these three supported
switches.
Note that comment /* KSZ879x/KSZ877x/KSZ876x Errata DS80000687C Module 2 */
is completely removed because it concerns the KSZ87xx family that doesn't
support at all EEE.
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20260608-clean-ksz-3rd-v2-6-6e61b7be23c4@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
