wait_event_interruptible_timeout() can return a negative error code when
interrupted by a signal. The original code treated all non-zero return
values as success, which would incorrectly synchronize DMA channels and
return 0 instead of propagating the interruption error.
Fixes: fa08b56686 ("spi: rzv2h-rspi: add support for DMA mode")
Signed-off-by: Felix Gu <ustc.gu@gmail.com>
Reviewed-by: Cosmin Tanislav <cosmin-gabriel.tanislav.xa@renesas.com>
Tested-by: Cosmin Tanislav <cosmin-gabriel.tanislav.xa@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://patch.msgid.link/20260627-rspi-v1-1-170c93ee14da@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This SPI controller likely belongs to a power domain for all the SoCs
listed. For sure, it belongs to one on the Renesas RZ/N1 SoC, so
enable the property to be able to describe its power domain in DTs.
Suggested-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Herve Codina <herve.codina@bootlin.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260626180326.9593-3-wsa+renesas@sang-engineering.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 164c05f03f ("spi: Convert DW SPI binding to DT schema") added
an RZ/N1 entry which was not in the original txt-file. It doesn't follow
the usual "<soc entry>, <soc family entry>" style for Renesas SoCs which
was properly added later with commit 029d32a892 ("spi: dw-apb-ssi:
Integrate Renesas RZ/N1 SPI controller"). In that commit, removing the
bogus entry was overlooked and is finally done now.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260626180326.9593-2-wsa+renesas@sang-engineering.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If request_irq() fails, report "can not request IRQ" rather than "can
not get IRQ" which may be misread as platform_get_irq() failure.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Link: https://patch.msgid.link/20260615044039.9750-3-jszhang@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Even with proper dma engine support, the first spi transfer always
fallback to PIO, the reason is the dws->n_bytes is 0 after
initialization, so the dw_spi_can_dma() calling from __spi_map_msg()
return false, thus both tx_sg_mapped and rx_sg_mapped are false, so
for the first spi transfer, the spi_xfer_is_dma_mapped() reports false
thus fallback to PIO.
Although this brings no harm, we can simply fix this issue by
calcuating the "n_bytes" from xfer->bits_per_word.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Link: https://patch.msgid.link/20260615044039.9750-2-jszhang@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
When an SPI controller operating in target mode has a transfer in
progress at the time of system suspend, the suspend path proceeds
without aborting the ongoing transfer. This can leave the hardware in
an inconsistent state, potentially causing the system to hang or fail
to resume cleanly.
Fix this by invoking the controller's target_abort callback from
spi_controller_suspend() when the controller is in target mode and the
callback is registered. This ensures any active target transfer is
cleanly terminated before the controller is suspended.
Signed-off-by: Praveen Talari <praveen.talari@oss.qualcomm.com>
Link: https://patch.msgid.link/20260625-abort_active_transfer_duirng_s2r-v2-1-1d6f724406b6@oss.qualcomm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
sh_msiof_spi_reset_regs() asserts TX/RX reset and polls until the reset
bits clear, but the poll result is ignored. sh_msiof_transfer_one() can
therefore continue programming a transfer after the controller did not
leave reset.
Return the reset poll result from the helper and abort the transfer on
timeout, matching the existing transfer path's error-return style.
Fixes: fedd694068 ("spi: sh-msiof: Add reset of registers before starting transfer")
Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn>
Link: https://patch.msgid.link/20260623135834.55442-1-pengpeng@iscas.ac.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
When spi_imx_can_dma() selects DMA, the ECSPI is configured for DMA:
spi_imx_setupxfer() sets CTRL.SMC and clears dynamic_burst, and
spi_imx_dma_transfer() programs the dynamic-burst BURST_LENGTH and the
SDMA watermarks.
If the DMA descriptor cannot be prepared (dmaengine_prep_slave_single()
returns NULL), the transfer is failed with SPI_TRANS_FAIL_NO_START and
falls back to PIO. The dynamic-burst DMA path uses its own bounce
buffers instead of the SPI core's mapping, so xfer->{tx,rx}_sg_mapped
are not set and the core's DMA->PIO retry is skipped; the driver falls
back to PIO internally. But none of the DMA-mode configuration is
undone, so the PIO transfer runs with CTRL.SMC set, the wrong burst
length and dynamic_burst cleared, and the transferred data is corrupted.
This is easily hit on i.MX8MP boards that describe ECSPI DMA in the
device tree but run SDMA on ROM firmware (no external sdma-imx7d.bin):
every ECSPI DMA prepare fails. An Infineon SLB9670 TPM on ECSPI1 then
returns shifted TPM2_GetCapability data, is flagged "field failure
mode", /dev/tpmrm0 is never created.
Set controller->fallback before re-running spi_imx_setupxfer() so the
ECSPI is reconfigured exactly like a normal PIO transfer. With
controller->fallback set, spi_imx_setupxfer() sees spi_imx_can_dma()
return false, so it clears spi_imx->usedma and reprograms the controller
(clears CTRL.SMC, restores dynamic_burst and the PIO burst length). No
explicit spi_imx->usedma = false is needed: setupxfer() already updates
it from the can_dma() result.
Fixes: faa8e404ad ("spi: imx: support dynamic burst length for ECSPI DMA mode")
Cc: stable@vger.kernel.org
Signed-off-by: Javier Fernandez Pastrana <javier.pastrana@linutronix.de>
Acked-by: Carlos Song <carlos.song@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260624151958.18626-1-javier.pastrana@linutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a new compatible entry "snps,dwc-ssi-2.00a" for the Synopsys
DesignWare SSI controller version 2.00a. This variant uses the same
initialization routine as snps,dwc-ssi-1.01a (dw_spi_hssi_init).
Signed-off-by: Changhuang Liang <changhuang.liang@starfivetech.com>
Link: https://patch.msgid.link/20260619143443.22267-3-changhuang.liang@starfivetech.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a new compatible string "starfive,jhb100-spi" for the StarFive
JHB100 SPI, it based on the Synopsys DesignWare SSI version 2.00a,
uses snps,dwc-ssi-2.00a as the primary fallback and snps,dwc-ssi-1.01a
as the secondary fallback.
Signed-off-by: Changhuang Liang <changhuang.liang@starfivetech.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://patch.msgid.link/20260619143443.22267-2-changhuang.liang@starfivetech.com
Signed-off-by: Mark Brown <broonie@kernel.org>
rpcif_spi_resume() currently passes the SPI controller device to
rpcif_hw_init(), but the function should be called with the RPC
interface device.
Retrieve the rpcif private data from the SPI controller and pass
rpc->dev instead. Also propagate the return value of rpcif_hw_init() so
that a failure during resume is properly reported rather than silently
ignored.
Fixes: ad4728740b ("spi: rpc-if: Add resume support for RZ/G3E")
Signed-off-by: Quang Nguyen <quang.nguyen.wx@renesas.com>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260618081932.172168-1-biju.das.jz@bp.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We do unneeded "double free" (emptying an empty list) in one case.
This is not a critical issue at all, the fix just makes code robust
against any possible future changes in the flow.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20260617092406.2649384-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
After resuming from suspend to ram, spi transfer stops working. Further
debugging shows that the BAUDR register isn't correctly set, this is
due to dws->current_freq doesn't match the HW BAUDR setting,
specifically, the dws->current_freq equals to speed_hz, but BAUDR is 0.
so the dw_spi_set_clk() in below code won't be called:
if (dws->current_freq != speed_hz) {
dw_spi_set_clk(dws, clk_div);
dws->current_freq = speed_hz;
}
The mismatch comes from dw_spi_shutdown_chip() when suspending.
Fix this mismatch by setting dws->current_freq to 0 as well when
clearing BAUDR reg in dw_spi_shutdown_chip().
Fixes: e24c745272 ("spi: controller driver for Designware SPI core")
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Link: https://patch.msgid.link/20260612002835.5240-1-jszhang@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver calls devm_request_irq() before initializing the completion
used by the interrupt handler. Because the interrupt may occur immediately
after devm_request_irq(), the handler may execute before init_completion().
This may result in calling complete() on an uninitialized completion,
causing undefined behavior. This has been observed with KASAN.
Fix this by initializing the completion before registering the IRQ.
Reported-by: Sangyun Kim <sangyun.kim@snu.ac.kr>
Reported-by: Kyungwook Boo <bookyungwook@gmail.com>
Fixes: 5ba155a4d4 ("spi: add SPI controller driver for UniPhier SoC")
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Link: https://patch.msgid.link/20260616011223.201357-1-hayashi.kunihiko@socionext.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Prevent NULL pointer dereference when spi_get_device_id() returns NULL,
which can happen when using driver_override without matching SPI ID entry.
Signed-off-by: guoqi0226 <guoqi0226@163.com>
Link: https://patch.msgid.link/20260616103018.105612-3-guoqi0226@163.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The SPI drivers read properties whose bindings use normal uint32 cells.
Using boolean or u16 helpers makes the access look like a different DT
encoding and causes the property checker to flag the call sites.
Use presence checks for unsupported properties and read numeric cell
properties through u32 helpers before assigning to driver fields.
Assisted-by: Codex:gpt-5-5
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20260612215017.1884893-1-robh@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The method the driver uses to determine the size of the FIFO has a
problem. What it currently does is this:
It stops the SPI hardware and writes to the TX FIFO register until TX
FIFO FULL asserts in the status register. But the hardware does not only
have the FIFO, it also has a shift register which can hold a byte. This
can be seen, when writing a byte to the FIFO (while the SPI hardware is
stopped,) the TX FIFO EMPTY is still empty. So, if we have a FIFO size
of 16 for example, the current method returns a 17.
This is a problem, at least when using the driver in irq mode. The same
size determined for the TX FIFO is also assumed for the RX FIFO. When a
SPI transaction wants to write the amount of the FIFO size or more
bytes, the following happens, for example with 16 bytes FIFO size:
The driver stops the SPI hardware and writes 17 bytes to the TX FIFO and
starts the SPI hardware and goes sleep.
The hardware then shifts out 17 bytes (FIFO + shift register) and
simultaneously reads bytes into the RX FIFO, but it only has 16 places,
so it looses one byte. Then TX FIFO empty asserts, wakes the driver
again, which has a fast path and reads 16 bytes from the RX FIFO, but
before reading the last 17th byte (which is lost) it does this:
sr = xspi->read_fn(xspi->regs + XSPI_SR_OFFSET);
if (!(sr & XSPI_SR_RX_EMPTY_MASK)) {
xilinx_spi_rx(xspi);
rx_words--;
}
It reads the status register and checks if the RX FIFO is not empty.
But it is empty in our case. So this check spins in a while loop
forever locking the driver.
This patch fixes the logic to determine the FIFO size.
Fixes: 4c9a761402 ("spi/xilinx: Simplify spi_fill_tx_fifo")
Signed-off-by: Lars Pöschel <lars.poeschel@edag.com>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Link: https://patch.msgid.link/20260612105244.9076-1-lars.poeschel.linux@edag.com
Signed-off-by: Mark Brown <broonie@kernel.org>
here focus on the shared spi-mem layer which is enhanced in order to
bring two new features:
- The possibility to fill a primary and a secondary operation template
in the direct mapping structure in order to support continuous reads
in SPI NAND, which may require two different read operations.
- SPI controllers may indicate possible CS instabilities over long
transfers by setting a boolean. This capability is related to the
previous one, the need for it has arised while testing SPI NAND
continuous reads with the Cadence QSPI controller which cannot, under
certain conditions, keep the CS asserted for the length of
an eraseblock-large transfer.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmn4m50ACgkQJWrqGEe9
VoSUzwf8D7an5inOVMcX2IsbXSkA6vKgrzjc1jG3rGiLrFks/bZyo0R8atp4pUsy
6WDkJfFyHg6IzU92N/37Kha8rnFp7um9OhfB/z2O/ztyqr9d1yM6QDtenknYr+WH
BwcuJ8zenyWuIY526Ar04REJ07s8MZpMUhcnUIw/KpvQiS12UR6NHgEaUrmIjtLD
GCKKFTGOY++9dgObo8ZrkrsLlVUhV5GyvCqUtBNNbADTNAt7j4m6YuyztS7rrmwb
b33RoZiWmG0szkUsTJJBDH15cMB/4wV2SoGm3wzsACHqJhCy0n9FvSVAXwcRm5l7
qOLedtMoBIIIIwBbHPsf0SySToy2ag==
=3qpz
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmosAyEACgkQJNaLcl1U
h9BOcgf9EtmCuxpcX2n0PQlE6j88fr/zFDArtOXFZNFKdhL46u2kUWhdrvDH8i0J
1FBbxRWsQqfrLesveqHqzVSg0ub6USe80Cbzjt2Vo1Ri+RF2i0b+5KNd1VrHC/iF
DG+8A2c4VmjdiuCkaNI1gixMqdRJHSSWEjGD61+rv4M/VBIr1YtAV5kIJ+tFLPoY
lYrvNMGcUGUTHUK2tJx4uaMuo7dd3C+hIWnnMu6OZ+TB/VbX77z4jrhqTONzxdYy
uV+Zxh1PPLBvysPsqwSXpdW2FjfUi2SSGYrNn+kw0pdb58Th3/x7Tocb3t7awfWU
Ah5Yw6zUF2vJMBFAOhHNJ9r3hvtoBw==
=WwE4
-----END PGP SIGNATURE-----
spi: spi-mem: Add a no_cs_assertion capability
Merge tag 'mtd/spi-mem-cont-read-for-7.2' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux into spi-7.2
Miquel Raynal <miquel.raynal@bootlin.com> says:
Aside from preparation changes in the SPI NAND core, the changes carried
here focus on the shared spi-mem layer which is enhanced in order to
bring two new features:
- The possibility to fill a primary and a secondary operation template
in the direct mapping structure in order to support continuous reads
in SPI NAND, which may require two different read operations.
- SPI controllers may indicate possible CS instabilities over long
transfers by setting a boolean. This capability is related to the
previous one, the need for it has arised while testing SPI NAND
continuous reads with the Cadence QSPI controller which cannot, under
certain conditions, keep the CS asserted for the length of
an eraseblock-large transfer.
In case of failed HW the driver may not see an interrupt and will stuck
in waiting forever. We can avoid such situation by timing out of
transfers if the interrupt is not seen in a reasonable time.
This problem can be found on unload of ptp_ocp driver for TimeCard which
uses Xilinx SPI AXI and SPI-NOR flash memory. During tear-down process
spi-nor drivers send soft reset command which is not triggering an
interrupt stalling the unload process completely.
Signed-off-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Acked-by: Michal Simek <michal.simek@amd.com>
Link: https://patch.msgid.link/20260610222843.782337-1-vadim.fedorenko@linux.dev
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert the Nuvoton NPCM FIU binding to DT schema format.
Document the required control registers and the optional direct-
mapped flash window separately, matching the driver behavior
when the direct mapping is not described.
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://patch.msgid.link/20260609163919.3321228-4-tmaimon77@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
pm_runtime_get_sync() increments the runtime PM usage counter even when it
returns an error. meson_spifc_remove() uses it to resume the controller
before disabling runtime PM, but never drops the usage counter again.
Balance the get with pm_runtime_put_noidle() after disabling runtime PM,
matching the teardown pattern used by other SPI controller drivers.
Found by static analysis. I do not have hardware to test this.
Fixes: c3e4bc5434 ("spi: meson: Add support for Amlogic Meson SPIFC")
Signed-off-by: Ruoyu Wang <ruoyuw560@gmail.com>
Link: https://patch.msgid.link/20260609052647.5-1-ruoyuw560@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Named initializers are better readable and more robust to changes of the
struct definition. This robustness is relevant for a planned change to
struct platform_device_id replacing .driver_data by an anonymous union.
While touching these arrays unify spacing and usage of commas.
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/3fcd432a505bb1bb7f8ef0fba9162243200b3347.1780606153.git.u.kleine-koenig@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add suspend/resume support to the rzv2h-rspi driver by implementing
suspend and resume callbacks that delegate to spi_controller_suspend()
and spi_controller_resume() respectively.
Signed-off-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Link: https://patch.msgid.link/20260608202509.3651345-1-tommaso.merciai.xr@bp.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver uses pcim_enable_device(), so IRQ vectors are automatically
freed by devres on driver detach. The explicit pci_free_irq_vectors()
calls in the probe error path and remove function are redundant.
Drop them and the now-unused error label.
Signed-off-by: Felix Gu <ustc.gu@gmail.com>
Link: https://patch.msgid.link/20260530-dw-pci-v1-1-5d2cf798b3c3@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If DMA setup fails after allocating the zeropage, the error path frees
the page but leaves espi->zeropage dangling. A subsequent call to
ep93xx_spi_release_dma() sees the non-NULL pointer and frees the page
again.
Clear the pointer after freeing in the error path of
ep93xx_spi_setup_dma().
Fixes: 626a96db11 ("spi/ep93xx: add DMA support")
Signed-off-by: Felix Gu <ustc.gu@gmail.com>
Link: https://patch.msgid.link/20260529-ep93xx-v1-1-9185070ca1fc@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 0c5b5c40dc ("spi: cadence-xspi: Add COMPILE_TEST support")
allows this driver to be built for 32-bit platforms, which causes a
semantic conflict with commit 4954d4eca4 ("spi: cadence-xspi: Support
32bit and 64bit slave dma interface"), as readsq() and writesq() are
only available when targeting 64-bit platforms:
drivers/spi/spi-cadence-xspi.c: In function 'cdns_xspi_sdma_read':
drivers/spi/spi-cadence-xspi.c:601:25: error: implicit declaration of function 'readsq'; did you mean 'readsl'? [-Wimplicit-function-declaration]
601 | readsq(src, buf, len >> 3);
| ^~~~~~
| readsl
drivers/spi/spi-cadence-xspi.c: In function 'cdns_xspi_sdma_write':
drivers/spi/spi-cadence-xspi.c:623:25: error: implicit declaration of function 'writesq'; did you mean 'writesl'? [-Wimplicit-function-declaration]
623 | writesq(dst, buf, len >> 3);
| ^~~~~~~
| writesl
As there are no known 32-bit platforms that use this controller, revert
compile testing support to restrict the driver to 64-bit platforms to
avoid burdening the driver with workarounds.
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Fixes: 4954d4eca4 ("spi: cadence-xspi: Support 32bit and 64bit slave dma interface")
Acked-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/20260606-spi-cadence-xspi-revert-compile-testing-v1-1-76219ea378bd@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The cdns xspi controller slave dma interface may support wider data
width. Wider I/O width can benefit performance. We can know the width
by checking the CTRL_FEATURES_REG's DMA_DATA_WIDTH bit, 0 means 32bit
1 means 64bit.
A simple test with QSPI nor flash on one arm64 platform:
Use 8bit slave dma data width (now):
# dd if=/dev/mtdblock0 of=/dev/null bs=8192 count=1000
1000+0 records in
1000+0 records out
8192000 bytes (7.8MB) copied, 1.368735 seconds, 5.7MB/s
Use 32bit slave dma data width:
# dd if=/dev/mtdblock0 of=/dev/null bs=8192 count=1000
1000+0 records in
1000+0 records out
8192000 bytes (7.8MB) copied, 1.088787 seconds, 7.2MB/s
Improved by 26.3%!
Use 64bit slave dma data width:
# dd if=/dev/mtdblock0 of=/dev/null bs=8192 count=1000
1000+0 records in
1000+0 records out
8192000 bytes (7.8MB) copied, 0.831104 seconds, 9.4MB/s
Improved by 64.9%!
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Link: https://patch.msgid.link/20260602235825.28614-1-jszhang@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
When the SPI controllers are running in DMA mode, it is the DMA engine
that performs the memory accesses rather than the SPI controller. Pass
the DMA engine's struct device pointer to the DMA API to make sure the
correct DMA operations are used.
Suggested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Aaron Kling <webgeek1234@gmail.com>
Link: https://patch.msgid.link/20260525-tegra194-qspi-iommu-v2-1-a11c53f804b2@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
dmaengine_terminate_all() has been deprecated, so replace it with
dmaengine_terminate_sync().
Fixes: ba9b28652c ("spi: imx: enable DMA mode for target operation")
Fixes: a450c8b77f ("spi: imx: handle DMA submission errors with dma_submit_error()")
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Link: https://patch.msgid.link/20260525062928.3191821-1-carlos.song@oss.nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Carlos Song (OSS) <carlos.song@oss.nxp.com> says:
This series fixes two issues in the fsl-lpspi DMA transfer error paths.
Patch 1 replaces the deprecated dmaengine_terminate_all() with
dmaengine_terminate_sync() across all error paths in
fsl_lpspi_dma_transfer().
Patch 2 fixes a missing RX DMA channel termination when TX descriptor
preparation fails. Since the RX channel is already submitted and issued
before the TX descriptor is prepared, returning -EINVAL without
terminating the RX channel leaves it running against buffers that the
SPI core will unmap, potentially causing memory corruption.
Link: https://patch.msgid.link/20260525062357.3191349-1-carlos.song@oss.nxp.com
When dmaengine_prep_slave_sg() fails for the TX channel, the error path
terminates the TX DMA channel but leaves the RX channel running. Since
the RX channel was already submitted and issued prior to preparing
the TX descriptor, returning -EINVAL causes the SPI core to unmap the
DMA buffers while the RX DMA engine continues writing to them, leading
to potential memory corruption or use-after-free.
Terminate the RX channel before returning on the TX prepare failure path.
Fixes: 09c04466ce ("spi: lpspi: add dma mode support")
Cc: stable@vger.kernel.org
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Link: https://patch.msgid.link/20260525062357.3191349-3-carlos.song@oss.nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The original code set use_dma to false when dma_alloc_coherent() for
bounce buffers failed, but DMA channels acquired earlier via
atmel_spi_configure_dma() were never freed.
When devm_request_irq() or clk_prepare_enable() failed later in probe,
the driver also did not release DMA channels or bounce buffers already
allocated.
The out_free_dma error path released DMA channels but did not free the
bounce buffers.
Fix by moving bounce buffer allocation into atmel_spi_configure_dma()
and registering the devres cleanup for DMA channels and bounce buffers.
Fixes: a9889ed62d ("spi: atmel: Implements transfers with bounce buffer")
Signed-off-by: Felix Gu <ustc.gu@gmail.com>
Link: https://patch.msgid.link/20260522-atmel-v3-1-23f8c6e6aa43@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
- Make the clearcpuid= boot parameter less prominent
and warn about its dangers & caveats (Borislav Petkov)
- Do not access the (new) PLATFORM_ID MSR when running as a guest
(Borislav Petkov)
- x86 ftrace: Relocate %rip-relative percpu refs in dynamic
trampolines, to fix crash when using such trampolines
(Alexis Lothoré)
- Fix x86-64 CFI build error (Peter Zijlstra)
- Revert FPU signal return magic number check optimization, because
it broke CRIU and gVisor in certain FPU configurations
(Andrei Vagin)
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=4sLh
-----END PGP SIGNATURE-----
Merge tag 'x86-urgent-2026-05-31' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
- Make the clearcpuid= boot parameter less prominent
and warn about its dangers & caveats (Borislav Petkov)
- Do not access the (new) PLATFORM_ID MSR when running
as a guest (Borislav Petkov)
- x86 ftrace: Relocate %rip-relative percpu refs in dynamic
trampolines, to fix crash when using such trampolines
(Alexis Lothoré)
- Fix x86-64 CFI build error (Peter Zijlstra)
- Revert FPU signal return magic number check optimization,
because it broke CRIU and gVisor in certain FPU configurations
(Andrei Vagin)
* tag 'x86-urgent-2026-05-31' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Revert "x86/fpu: Refine and simplify the magic number check during signal return"
x86/kvm/vmx: Fix x86_64 CFI build
x86/ftrace: Relocate %rip-relative percpu refs in dynamic trampolines
x86/microcode: Do not access MSR_IA32_PLATFORM_ID when running as a guest
Documentation/arch/x86: Hide clearcpuid=
Two core changes, the only one of significance being the change to kick queues
in SDEV_CANCEL which had a small window for stuck requests. The major driver
fixes are the one to the FC transport class to widen the FPIN counter to
counter a theoretical (and privileged) fabric traffic injection attack and the
other is an iscsi fix where a malicious target could trick the kernel into an
output buffer overrun. Both the driver fixes were AI assisted.
Signed-off-by: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
-----BEGIN PGP SIGNATURE-----
iLgEABMIAGAWIQTnYEDbdso9F2cI+arnQslM7pishQUCahxQ/RsUgAAAAAAEAA5t
YW51MiwyLjUrMS4xMiwyLDImHGphbWVzLmJvdHRvbWxleUBoYW5zZW5wYXJ0bmVy
c2hpcC5jb20ACgkQ50LJTO6YrIX+HgD+Mqf+AKbV/EhPhKAfONeBaE0Q5e78KTyK
3e47Qxjs+mQBAKhWUwodLDS/WSm7Fbdj7tn/kuPSaH+R+JQltnPR4QPG
=BRJ7
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two core changes, the only one of significance being the change to
kick queues in SDEV_CANCEL which had a small window for stuck
requests.
The major driver fixes are the one to the FC transport class to widen
the FPIN counter to counter a theoretical (and privileged) fabric
traffic injection attack and the other is an iscsi fix where a
malicious target could trick the kernel into an output buffer overrun.
Both the driver fixes were AI assisted"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: target: iscsi: Validate CHAP_R length before base64 decode
scsi: target: iscsi: Bound iscsi_encode_text_output() appends to rsp_buf
scsi: target: iscsi: Fix CRC overread and double-free in iscsit_handle_text_cmd()
scsi: fcoe: Reject FIP descriptors with zero fip_dlen in CVL walker
scsi: scsi_transport_fc: Widen FPIN pname walker counter to u32
scsi: scsi_debug: Add missing newline in scsi_debug_device_reset()
scsi: megaraid_sas: Fix NULL pointer dereference on firmware duplicate completion
scsi: devinfo: Add BLIST_NO_RSOC for Promise VTrak E310f
scsi: core: Run queues for all non-SDEV_DEL devices from scsi_run_host_queues
davinci: fix fallback bus frequency on missing clock-frequency
virtio: mark device ready initially
-----BEGIN PGP SIGNATURE-----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=AcAd
-----END PGP SIGNATURE-----
Merge tag 'i2c-for-7.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
- davinci: fix fallback bus frequency on missing clock-frequency
- virtio: mark device ready initially
* tag 'i2c-for-7.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: virtio: mark device ready before registering the adapter
i2c: davinci: fix division by zero on missing clock-frequency
- updates to Elan I2C touchpad driver to handle a new IC type and to
validate size of supplied firmware to prevent OOB access
- updates to Xpad controller driver to recognize ASUS ROG RAIKIRI II and
"Nova 2 Lite" from GameSir controllers as well as a fix to prevent a
potential OOB access when handling "Share" button
- an update to Synaptics touchpad driver to use RMI mode for touchpad in
Thinkpad E490
- updates to Atmel MXT driver adding checks to prevent potential OOB
accesses
- a fix to IMS PCU driver to free correct amount of memory when
tearing it down
- a fixup to the recent change to Atlas buttons driver
- a small cleanup in fm801-fp for PCI IDs table initialisation
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQST2eWILY88ieB2DOtAj56VGEWXnAUCahvBFwAKCRBAj56VGEWX
nP7XAQDH9WIYBX7XEHSPInN6GH8GngWA/94v3b6UpBSL2UFdQQEAo1+WoyOGL/Dh
0U0g5CcvDwx9irF8qJBWX2a3DRNPngo=
=hDBA
-----END PGP SIGNATURE-----
Merge tag 'input-for-v7.1-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
- updates to Elan I2C touchpad driver to handle a new IC type and to
validate size of supplied firmware to prevent OOB access
- updates to Xpad controller driver to recognize ASUS ROG RAIKIRI II
and "Nova 2 Lite" from GameSir controllers as well as a fix to
prevent a potential OOB access when handling "Share" button
- an update to Synaptics touchpad driver to use RMI mode for touchpad
in Thinkpad E490
- updates to Atmel MXT driver adding checks to prevent potential OOB
accesses
- a fix to IMS PCU driver to free correct amount of memory when tearing
it down
- a fixup to the recent change to Atlas buttons driver
- a small cleanup in fm801-fp for PCI IDs table initialisation
* tag 'input-for-v7.1-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: ims-pcu - fix usb_free_coherent() size in ims_pcu_buffers_free()
Input: synaptics - add LEN2058 to SMBus passlist for ThinkPad E490
Input: atlas - check ACPI_COMPANION() against NULL
Input: atmel_mxt_ts - check mem_size before calculating config memory size
Input: atmel_mxt_ts - fix boundary check in mxt_prepare_cfg_mem
Input: fm801-gp - simplify initialisation of pci_device_id array
Input: xpad - add "Nova 2 Lite" from GameSir
Input: xpad - add support for ASUS ROG RAIKIRI II
Input: elan_i2c - validate firmware size before use
Input: xpad - fix out-of-bounds access for Share button
Input: usbtouchscreen - clamp NEXIO data_len/x_len to URB buffer size
Input: elan_i2c - increase device reset wait timeout after update FW
Input: elan_i2c - add ic type 0x19
* fix order calculation for kho_unpreserve_pages() to make sure sure that
the order calculation in kho_unpreserve_pages() mathes the order
calculation in kho_preserve_pages().
* fix math in calculation of KHO_TREE_MAX_DEPTH to make it work with 16KB
pages.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEeOVYVaWZL5900a/pOQOGJssO/ZEFAmobGd4ACgkQOQOGJssO
/ZGaRQf/a0vTak489XqXhddHkulyMnif1UEEYsltxQ8bJkC0SRx+v/PcC0Uf2g7+
n/1vQZxWGUlLawjMDhubCWp2JawRZh9/rzPfb96z3nsjUckaQI3sKdEe7fK9jIVL
2y2QHa26RJj7dlEcJbUToSgVbRrP8qJbiUVjo1i3ViVFsevj1gaNBo8h8oJa694z
S1wXndBz7HYdSNuRgMc5rGUbzgVu9rl2rdTHR6ecRUfTVuQr1ZYrb7v6wi4AI3XL
KZp6TXmDuvPikJwoWsQtBRK5VmLQxsCa5ryu4M+GEBOwezNZex29Yi2TrZWZ2KZk
ViCFzYQLHY7RUrlhL7+tGN2SiLYKqg==
=LtZL
-----END PGP SIGNATURE-----
Merge tag 'liveupdate-fixes-2026-05-30' of git://git.kernel.org/pub/scm/linux/kernel/git/liveupdate/linux
Pull liveupdate fixes from Mike Rapoport:
"Two kexec handover regression fixes:
- fix order calculation for kho_unpreserve_pages() to make sure sure
that the order calculation in kho_unpreserve_pages() mathes the
order calculation in kho_preserve_pages().
- fix math in calculation of KHO_TREE_MAX_DEPTH to make it work with
16KB pages"
* tag 'liveupdate-fixes-2026-05-30' of git://git.kernel.org/pub/scm/linux/kernel/git/liveupdate/linux:
kho: fix order calculation for kho_unpreserve_pages()
kho: fix KHO_TREE_MAX_DEPTH for non-4KB page sizes
After refactoring of memblock_free_late() and free_init_pages() it became
possible to call memblock_free() after memblock init data was discarded.
Make sure memblock_free() does not touch memblock.reserved unless it is
called early enough or when ARCH_KEEP_MEMBLOCK is enabled.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEeOVYVaWZL5900a/pOQOGJssO/ZEFAmobERsACgkQOQOGJssO
/ZGiqQgArOfAxLDWWinyherNcejWY+GKsNdWNYoGOv8UEw2oTTBmjyrOqHrGcevQ
YlLjBxc2v9LzW9wCRnW0ngoq6/28ABLwyLpB+sMyHU8KaJDyYnAhfe7xt59aqE2N
JuQaSRY8irZG8g2Yks2ZWIPbDoIXJVvGI342L96OYLO63eehV9u5e7kbBebOZpH1
JlnbsaMGjhh2RgLrWWEy4EW1NZ5bYHer6fmCVIlUWtz9X67OjKD5na8bdi9ADEay
Wu2CjYwZFdScM4FQ8r2l9UHxjnU8EQKRxVOm2+hO8wRiE3efzezDCp5Laacvf9o6
KLrkVONfYUpScis3qLpNZly3IjAeVw==
=H1VN
-----END PGP SIGNATURE-----
Merge tag 'fixes-2026-05-30' of git://git.kernel.org/pub/scm/linux/kernel/git/rppt/memblock
Pull memblock fix from Mike Rapoport:
"Fix regression from memblock_free_late() refactoring
After refactoring of memblock_free_late() and free_init_pages() it
became possible to call memblock_free() after memblock init data was
discarded.
Make sure memblock_free() does not touch memblock.reserved unless it
is called early enough or when ARCH_KEEP_MEMBLOCK is enabled"
* tag 'fixes-2026-05-30' of git://git.kernel.org/pub/scm/linux/kernel/git/rppt/memblock:
memblock: don't touch memblock arrays when memblock_free() is called late
Commit eac69475b0 ("media: rc: igorplugusb: heed coherency
rules") changed the control request storage from an embedded struct to
an allocated pointer so it can obey DMA coherency rules.
However, the driver still passes &ir->request to usb_fill_control_urb().
That points the URB setup packet at the pointer field itself rather than
at the allocated struct usb_ctrlrequest.
USB core then interprets pointer bytes as the setup packet. This can
produce an invalid bRequestType and trigger the control direction warning
reported by syzbot:
usb 2-1: BOGUS control dir, pipe 80003580 doesn't match bRequestType 0
Pass ir->request itself as the setup packet.
Fixes: eac69475b0 ("media: rc: igorplugusb: heed coherency rules")
Reported-by: syzbot+11f0e4f957c7c3bf3d51@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=11f0e4f957c7c3bf3d51
Tested-by: syzbot+11f0e4f957c7c3bf3d51@syzkaller.appspotmail.com
Cc: stable@vger.kernel.org
Assisted-by: Codex:GPT-5.5
Signed-off-by: Henri A <contact@henrialfonso.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Here is a set of USB fixes and new device ids for 7.1-rc6. Nothing
major in here, just lots of tiny fixes for reported issues found by
users and some older patches found by some scanning tools. Included in
here are:
- typec fixes found by fuzzers that have decided to finally look at
that device interaction path (i.e. before a driver is bound to a
device).
- typec fixes for issues found by users
- thunderbolt driver fixes for reported problems
- cdns3 driver fixes
- dwc3 driver fixes
- new device quirks added
- usb serial driver fixes for broken devices
- other small driver fixes
All of these have been in linux-next for over a week with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCahrHyA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymLRgCeN/oLFmGYFHjcJEZ8d0AjKbRS34oAn3r822bO
1mEsGeOojdWNUm4wzu1k
=pf1m
-----END PGP SIGNATURE-----
Merge tag 'usb-7.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB and Thunderbolt fixes from Greg KH:
"Here is a set of USB fixes and new device ids for 7.1-rc6. Nothing
major in here, just lots of tiny fixes for reported issues found by
users and some older patches found by some scanning tools. Included in
here are:
- typec fixes found by fuzzers that have decided to finally look at
that device interaction path (i.e. before a driver is bound to a
device)
- typec fixes for issues found by users
- thunderbolt driver fixes for reported problems
- cdns3 driver fixes
- dwc3 driver fixes
- new device quirks added
- usb serial driver fixes for broken devices
- other small driver fixes
All of these have been in linux-next for over a week with no reported
issues"
* tag 'usb-7.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (54 commits)
USB: serial: cypress_m8: validate interrupt packet headers
USB: serial: safe_serial: fix memory corruption with small endpoint
USB: serial: omninet: fix memory corruption with small endpoint
USB: serial: mxuport: fix memory corruption with small endpoint
USB: serial: cypress_m8: fix memory corruption with small endpoint
USB: cdc-acm: Fix bit overlap and move quirk definitions to header
usb: dwc2: Fix use after free in debug code
usb: chipidea: core: convert ci_role_switch to local variable
usb: gadget: f_fs: serialize DMABUF cancel against request completion
usb: gadget: f_fs: copy only received bytes on short ep0 read
usb: gadget: dummy_hcd: Reject hub port requests for non-existent ports
dt-bindings: usb: Fix EIC7700 USB reset's issue
usbip: vudc: Fix use after free bug in vudc_remove due to race condition
dt-bindings: usb: ti,omap4-musb: Drop duplicate 'usb-phy' property constraints
usb: storage: Add quirks for PNY Elite Portable SSD
USB: quirks: add NO_LPM for Lenovo ThinkPad USB-C Dock Gen2 hub controllers
usb: usbtmc: reject interrupt endpoints with small wMaxPacketSize
usb: usbtmc: check URB actual_length for interrupt-IN notifications
xhci: tegra: Fix ghost USB device on dual-role port unplug
usb: gadget: uvc: hold opts->lock across XU walks in uvc_function_bind
...
Here are some small serial driver fixes for 7.1-rc6. Included in here
are:
- mips serial driver fixes to resolve some long-standing issues with
how they interacted with the console. That's the "majority" of the
changes in this merge request
- sh-sci driver regression fix
- 8250 driver regression fixes
- other small serial driver fixes for reported problems.
All of these have been in linux-next for over a week with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCahrImA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykedQCfb1CR0Z6lElo/02m3wmR+EfvGyoUAoLj8QU71
dFaLWzZQk8Hb6ajmVYK5
=tgAC
-----END PGP SIGNATURE-----
Merge tag 'tty-7.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are some small serial driver fixes for 7.1-rc6. Included in here
are:
- mips serial driver fixes to resolve some long-standing issues with
how they interacted with the console. That's the "majority" of the
changes in this merge request
- sh-sci driver regression fix
- 8250 driver regression fixes
- other small serial driver fixes for reported problems.
All of these have been in linux-next for over a week with no reported
issues"
* tag 'tty-7.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: dz: Enable modular build
serial: zs: Convert to use a platform device
serial: dz: Convert to use a platform device
serial: zs: Switch to using channel reset
serial: zs: Fix bootconsole handover lockup
serial: dz: Fix bootconsole handover lockup
serial: dz: Fix bootconsole message clobbering at chip reset
serial: 8250_dw: dispatch SysRq character in dw8250_handle_irq()
serial: 8250: dispatch SysRq character in serial8250_handle_irq()
serial: core: introduce guard(uart_port_lock_check_sysrq_irqsave)
tty: serial: samsung: Remove redundant port lock acquisition in rx helpers
serial: altera_jtaguart: handle uart_add_one_port() failures
serial: qcom_geni: fix kfifo underflow when flush precedes DMA completion IRQ
serial: fsl_lpuart: fix rx buffer and DMA map leaks in start_rx_dma
tty: add missing tty_driver include to tty_port.h
serial: qcom-geni: fix UART_RX_PAR_EN bit position
serial: sh-sci: fix memory region release in error path
tty: serial: pch_uart: add check for dma_alloc_coherent()
serial: zs: Fix swapped RI/DSR modem line transition counting
Here are some small char/misc/iio driver fixes for 7.1-rc6. Included in
here are:
- lots of small IIO driver fixes for reported problems.
- Android binder bugfixes for reported issues.
- small comedi test driver fixes
- counter driver fix
- parport driver fix (people still use this?)
- rpi driver fix
- uio driver fix
All of these have been in linux-next for over a week with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCahrJeQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykKIwCfelyNaZgO2yRfSS1fGmzSv3+W8+sAoK5QHkEY
TvJIOm1Cwi8/n3vI42Hz
=EB+S
-----END PGP SIGNATURE-----
Merge tag 'char-misc-7.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc/iio fixes from Greg KH:
"Here are some small char/misc/iio driver fixes for 7.1-rc6. Included
in here are:
- lots of small IIO driver fixes for reported problems.
- Android binder bugfixes for reported issues.
- small comedi test driver fixes
- counter driver fix
- parport driver fix (people still use this?)
- rpi driver fix
- uio driver fix
All of these have been in linux-next for over a week with no reported
problems"
* tag 'char-misc-7.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (41 commits)
Revert "gpib: cb7210: Fix region leak when request_irq fails"
misc: rp1: Send IACK on IRQ activate to fix kdump/kexec
gpib: cb7210: Fix region leak when request_irq fails
parport: Fix race between port and client registration
uio: uio_pci_generic_sva: fix double free of devm_kzalloc() memory
rust_binder: Avoid holding lock when dropping delivered_death
rust_binder: avoid calling pending_oneway_finished() on TF_UPDATE_TXN
comedi: comedi_test: fix check for valid scan_begin_src in waveform_ai_cmdtest()
comedi: comedi_test: Fix limiting of convert_arg in waveform_ai_cmdtest()
iio: adc: viperboard: Fix error handling in vprbrd_iio_read_raw
iio: gyro: itg3200: fix i2c read into the wrong stack location
iio: dac: ad5686: fix powerdown control on dual-channel devices
iio: dac: ad5686: acquire lock when doing powerdown control
iio: temperature: tsys01: fix broken PROM checksum validation
iio: dac: ad3530r: Fix AD3531/AD3531R powerdown mode strings
iio: buffer: hw-consumer: fix use-after-free in error path
iio: dac: ad5686: fix input raw value check
iio: dac: ad5686: fix ref bit initialization for single-channel parts
iio: ssp_sensors: cancel delayed work_refresh on remove
iio: adc: meson-saradc: fix calibration buffer leak on error
...
virtio_i2c_probe() synchronously probes child i2c drivers on the bus,
but peripherals may use the bus at probe for tasks like reading a chip
id. The vhost-user-i2c backend stalls at such probes unless DRIVER_OK
is already set before the virtqueue is first kicked.
Set DRIVER_OK explicitly before i2c_add_adapter(), as done for the
same reason in commit f5866db64f ("virtio_console: enable VQs
early") and commit 71e4b8bf04 ("virtio_rpmsg: set DRIVER_OK before
using device").
Signed-off-by: Alexis Bouzigues <BouziguesAlexis@JohnDeere.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
davinci: fix fallback bus frequency on missing clock-frequency
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQScDfrjQa34uOld1VLaeAVmJtMtbgUCahpiiQAKCRDaeAVmJtMt
bp+eAQDfsx42uAWytASKf7/lFJcPJvlBPXMa5ZwwqtwlBW+jPwEAned0rKUYyIGz
bpVpIO+H3iiaG325v9dxD56rmu9eEwE=
=Vmap
-----END PGP SIGNATURE-----
Merge tag 'i2c-host-fixes-7.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/andi.shyti/linux into i2c/for-current
i2c-host-fixes for v7.1-rc6
davinci: fix fallback bus frequency on missing clock-frequency
