After init mes queue, it require some time for mes to execute init
code including setup version info in CP_MES_GP3 register. Put it after
first MES call(set_hw_resource package).
Signed-off-by: Shaoyun Liu <shaoyun.liu@amd.com>
Reviewed-by: Michael Chen <michael.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
From MES version 0x74 and above, pipe 1(kiq) support use the
shared command buffer to distribute the tasks among the xccs
within the same partition. It's more efficient for tlb invalidation
been done individually on the each XCC at the same time compare
to let master xcc loop all xccs.
This requires the coop_mode been set before kiq set_hw_resource.
Signed-off-by: Shaoyun Liu <shaoyun.liu@amd.com>
Reviewed-by: Michael Chen <michael.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Support for TOC fw load for psp v15_0_8 rev id 0.
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support to load rlc firmware for rev_id 0 of gfx v12_1.
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add logging for thermal events in SMUv15.0.8 SOCs
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Asad Kamal <asad.kamal@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add mem temp to gpu metrics as maximum hbm stack temperature
for smu_v15_0_8
Signed-off-by: Asad Kamal <asad.kamal@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add partition metrics support for smu_v15_0_8
Signed-off-by: Asad Kamal <asad.kamal@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Increase reserved memory to 150 MB.
v2: squash in fixes (Alex)
Signed-off-by: Alex Sierra <alex.sierra@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update CP command package for gfx v12.1.
1. Update to common command pkg format for PACKET3_ACQUIRE_MEM.
2. Update to definition PACKET3_PRED_EXEC command pkt.
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Same as compute and sdma, gfx_hqd_mask has been initialized properly in
amdgpu_mes_init. set_hw_res should use those initialization accordingly.
Hardcoding it causes the mismatch between driver and MES.
Signed-off-by: Amber Lin <Amber.Lin@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
amdgpu_gem_align_pitch() is passed u32 width and cpp from dumb buffer
creation but uses signed int internally. The round-up add and the
aligned * cpp multiplication can overflow, returning zero or a negative
pitch. A zero pitch propagates to a zero-sized GEM object allocation
that reaches userspace via DRM_IOCTL_MODE_CREATE_DUMB.
Switch the helper to unsigned int and use check_add_overflow() /
check_mul_overflow() so wraparound returns zero. Reject a zero pitch
or size in amdgpu_mode_dumb_create() rather than allocating a zero-
byte BO.
Fixes: 8e911ab770 ("drm: amdgpu: Replace drm_fb_get_bpp_depth() with drm_format_plane_cpp()")
Signed-off-by: Werner Kasselman <werner@verivus.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Replace sprintf() with snprintf() to fix the -Werror=format-overflow
warning when building with allmodconfig:
drivers/gpu/drm/amd/amdgpu/jpeg_v2_5.c:152:47: error: '%d' directive
writing between 1 and 11 bytes into a region of size 7
[-Werror=format-overflow=]
152 | sprintf(ring->name, "jpeg_dec_%d", i);
The ring->name buffer is 16 bytes. Using snprintf() with sizeof()
ensures the buffer cannot overflow regardless of the integer value.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In dce6_available_bandwidth() and dce8_available_bandwidth(), replace
nested min() calls with min3().
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Remove Q10 rounding when applying smu_v15_0_8 static metrics
to the driver PPTable as the firmware now provide raw data
Signed-off-by: Asad Kamal <asad.kamal@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
ttm jobs must have higher priority than any userspace jobs.
Signed-off-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Makes a code slightly clearer and reduces indentation.
---
v5: use amdgpu_in_reset in amdgpu_ttm_disable_buffer_funcs
---
Signed-off-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Suggested-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is the only use case for this function.
---
v2: amdgpu_ttm_clear_buffer instead of amdgpu_clear_buffer
---
Signed-off-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It's doing the same thing as amdgpu_fill_buffer(src_data=0), so drop it.
The only caveat is that amdgpu_res_cleared() return value is only valid
right after allocation.
---
v2: introduce new "bool consider_clear_status" arg
v6: dont pass a NULL resv when calling amdgpu_fill_buffer from
amdgpu_bo_create
---
Signed-off-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
With this change we now have as many clear and move entities as we
have sdma engines (limited to TTM_NUM_MOVE_FENCES).
To enable load-balancing this patch gives access to all sdma
schedulers to all entities, except default_entity which has no
use for multiple schedulers.
---
v6: add comment
---
Signed-off-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This enables parallelism of operations.
Signed-off-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It's possible that some sdma instances aren't working so we shouldn't try
to use them from TTM. To achieve this, delay the call to
amdgpu_sdma_set_buffer_funcs_scheds after the rings have been tested, and
then use the 'ready' property to decide if a sched should be used or not.
Note that currently it's not doing much, because if the ring helper fails
for any ring, the whole sdma block init fails.
---
v5: check buffer_funcs_enabled from amdgpu_ttm_access_memory_sdma
---
Signed-off-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This will allow the use of all of them for clear/fill buffer
operations.
Since drm_sched_entity_init requires a scheduler array, we
store schedulers rather than rings. For the few places that need
access to a ring, we can get it from the sched using container_of.
Since the code is the same for all sdma versions, add a new
helper amdgpu_sdma_set_buffer_funcs_scheds to set buffer_funcs_scheds
based on the number of sdma instances.
Note: the new sched array is identical to the amdgpu_vm_manager one.
These 2 could be merged.
Signed-off-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Acked-by: Felix Kuehling <felix.kuehling@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
amdgpu_userq_wait_ioctl() takes extra references on waited-on fence
drivers and stores them in waitq->fence_drv_xa. When a new userq fence is
created, those references are transferred into userq_fence->fence_drv_array
so they can be released when the fence completes.
However, those inherited references are currently only dropped from
amdgpu_userq_fence_driver_process(). If a fence never reaches that path,
such as it is already signaled when created, so we need to explicitly release
those fences in that case.
v2: use a list(list_cut_before) for managing the signal userq driver fences.(Christian)
Link: https://patchwork.freedesktop.org/patch/718078/?series=164763&rev=2
v3: Doesn't cache the userq first unsignaled fence and use the cut before list
head directly.(Christian)
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In amdgpu_userq_destroy once unmap_helpder is called within mutex
there is no need to hold mutex.
This helps in avoiding a deadlock between doorbell and wptr ww mutex
and we could unpin and unref these bos outside mutex safely.
Signed-off-by: Sunil Khatri <sunil.khatri@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use pm_runtime_resume_and_get instead of pm_runtime_get_sync as it
return error but put the reference in the function itself.
In goto statements we need to drop the pm reference too.
Signed-off-by: Sunil Khatri <sunil.khatri@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We check for return value of amdgpu_userq_unmap_helper and
compare it against the queue->state which is logically
wrong and we should just check for failure and do the needfull.
Signed-off-by: Sunil Khatri <sunil.khatri@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Unmap the queue after freeing doorbell and wptr memory is completely
wrong. Any operation on the queue needs the doorbell and wptr to be
valid and hence fixing the ordering.
Also since we are using amdgpu_bo_reserve in non interruptrable mode
so there is no need to check for its return values.
Signed-off-by: Sunil Khatri <sunil.khatri@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Caller should hold the reservation lock for root.bo in func
amdgpu_userq_input_va_validate.
Signed-off-by: Sunil Khatri <sunil.khatri@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In function amdgpu_userq_buffer_vas_list_cleanup, remove the
reservation lock for vm and caller should make sure it's taken
before locking userq_mutex.
Signed-off-by: Sunil Khatri <sunil.khatri@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reshuffle the code to run create_mqd outside the mutex.
code here is mostly setting up software structure init
before actually registering the userqueue in the xa and
to the driver.
Signed-off-by: Sunil Khatri <sunil.khatri@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Do not hold reservation lock for root bo if userq_mutex
is already held in the call flow this cause a lock
issue with ttm_bo_delayed_delete.
Its better to lock the vm->root.bo first and then go ahead
with userq_mutex so userq_mutex threads dont get stuck until
the reservation lock is held.
In this case it helps in the function amdgpu_userq_buffer_vas_mapped
for each queue during restore_all.
Signed-off-by: Sunil Khatri <sunil.khatri@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Move the comment for the caller to the definition for
amdgpu_userq_ensure_ev_fence in kerneldoc format.
Signed-off-by: Sunil Khatri <sunil.khatri@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If the queue creation failed during mapping of the important VA's
like queue_va, rptr_va and wptr_va. These needs to be cleaned
as queue destroy will not be called for such queues as user never
get call to creation failure.
Signed-off-by: Sunil Khatri <sunil.khatri@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reorganise code to avoid holding mutex userq_mutex while
also trying to grab exec lock ww_mutex where its not needed
for function amdgpu_userq_input_va_validate
Signed-off-by: Sunil Khatri <sunil.khatri@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The Idle State Manager (ISM) uses delayed work to apply display idle
optimizations later, instead of immediately. This helps avoid rapid idle
transitions that can hurt power or performance.
A crash was seen during driver teardown. The system boots normally and
the driver loads successfully. Later, when the GPU is being stopped, the
log shows:
amdgpu 0000:0e:00.0: finishing device.
Workqueue: events_unbound dm_ism_sso_delayed_work_func [amdgpu]
After this, delayed ISM work still runs and reaches:
dm_ism_sso_delayed_work_func()
-> amdgpu_dm_ism_commit_event()
-> dm_ism_commit_idle_optimization_state()
-> dc_allow_idle_optimizations_internal()
The crash report showed:
KASAN: null-ptr-deref in range [0x690-0x697]
Signature:
[22601.113316] KASAN: null-ptr-deref in range [0x0000000000000690-0x0000000000000697]
...
[22601.113368] Workqueue: events_unbound dm_ism_sso_delayed_work_func [amdgpu]
[22601.113930] RIP: 0010:dc_allow_idle_optimizations_internal+0xa6/0xc40 [amdgpu]
...
[22601.114491] RDX: dffffc0000000000 RSI: 0000000000000000 RDI: 0000000000000690
...
[22601.114561] Call Trace:
[22601.114566] <TASK>
[22601.114572] ? srso_alias_return_thunk+0x5/0xfbef5
[22601.114582] ? update_load_avg+0x1b6/0x20b0
[22601.114593] ? __pfx_dc_allow_idle_optimizations_internal+0x10/0x10 [amdgpu]
[22601.114932] ? psi_group_change+0x4ed/0x8d0
[22601.114942] dm_ism_commit_idle_optimization_state+0x214/0x570 [amdgpu]
[22601.115268] amdgpu_dm_ism_commit_event+0xe1d/0x15a0 [amdgpu]
[22601.115588] ? srso_alias_return_thunk+0x5/0xfbef5
[22601.115595] ? __kasan_check_write+0x18/0x20
[22601.115603] ? srso_alias_return_thunk+0x5/0xfbef5
[22601.115610] ? mutex_lock+0x83/0xc0
[22601.115620] dm_ism_sso_delayed_work_func+0x64/0x90 [amdgpu]
GDB resolved dc_allow_idle_optimizations_internal+0xa6 to:
struct dc_state *context = dc->current_state;
The matching disassembly showed:
mov %rdi, %r12
mov 0x690(%r12), %r13
where r12 holds the dc pointer. A GDB layout dump of struct dc showed:
/* 1680 | 8 */ struct dc_state *current_state;
Since 1680 decimal is 0x690, this confirms that current_state is at
offset 0x690. The faulting access was effectively:
dc + 0x690
which indicates that dc was NULL at the time of dereference.
This shows that ISM work can still run during teardown after dc has
been cleared.
ISM is not expected to run after dc is destroyed. Fix this by disabling
ISM under dc_lock in amdgpu_dm_fini() before dc_destroy(), ensuring no
further ISM work runs after dc teardown.
Also add ASSERT(dm->dc) in amdgpu_dm_ism_commit_event() to enforce this
invariant, and ASSERT(mutex_is_locked(&dm->dc_lock)) in
amdgpu_dm_ism_disable() to clarify the locking requirement.
Fixes: 754003486c ("drm/amd/display: Add Idle state manager(ISM)")
Suggested-by: Leo Li <sunpeng.li@amd.com>
Cc: Ray Wu <ray.wu@amd.com>
Cc: Roman Li <roman.li@amd.com>
Cc: Alex Hung <alex.hung@amd.com>
Cc: Tom Chung <chiahsuan.chung@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Mario Limonciello (AMD) <superm1@kernel.org>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On PREEMPT_RT kernels, vfree() can sleep because spin_lock is
converted to rt_mutex. dml2_destroy() calls vfree() while inside
an FPU-guarded region (preempt_count=2), which is illegal.
dml2_wrapper_fpu.c is compiled with CC_FLAGS_FPU which defines
_LINUX_FPU_COMPILATION_UNIT, making DC_RUN_WITH_PREEMPTION_ENABLED()
resolve to a no-op. This prevents the macro from cycling FPU
context off/on around vfree().
Move dml2_destroy() to dml2_wrapper.c (non-FPU compilation unit)
where DC_RUN_WITH_PREEMPTION_ENABLED() properly cycles DC_FP_END/
DC_FP_START around vfree(). This pairs it with dml2_allocate_memory()
which already lives there.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Rafal Ostrowski <rafal.ostrowski@amd.com>
Signed-off-by: Chenyu Chen <chen-yu.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The driver stores EDID in amdgpu_connector->edid and uses it as a cache.
amdgpu_connector_get_edid() checks this pointer. If it is not NULL, it
assumes EDID is already present and does not read it again.
In some detect paths, the driver frees the EDID using drm_edid_free(),
but does not set the pointer to NULL. Because of this, the pointer still
looks valid even though the memory is already freed.
Later, when amdgpu_connector_get_edid() is called, it returns early and
does not read a new EDID. This can lead to using a freed pointer.
Fix this by setting amdgpu_connector->edid = NULL after drm_edid_free().
This makes sure the driver reads a fresh EDID and does not use invalid
memory.
Fixes: 71036457ad ("drm/amdgpu/amdgpu_connectors: remove amdgpu_connector_free_edid")
Reported-by: Dan Carpenter <error27@gmail.com>
Cc: Joshua Peisach <jpeisach@ubuntu.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Joshua Peisach <jpeisach@ubuntu.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DC v3.2.378 summary:
New:
- Add p-state schedule admissibility flags and frame-time utility
Fixes:
- Fixed incorrect math_mod() result due to wrong variable in fmod implementation (Cc: stable)
- Use overlay cursor when a color pipeline is active to avoid incorrect rendering
Cleanups:
- Add const qualifiers to watermark params struct
- Fix narrowing-conversion compiler warnings
Signed-off-by: Taimur Hassan <Syed.Hassan@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Core needs to track pstate schedule admissibility for different global
change scenarios (fclk, temp read, PPT) and requires a reusable way to compute
per-stream frame time from timing parameters.
[How]
Extend dml2_core_internal_mode_support_info with:
fclk_pstate_schedule_admissible
temp_read_pstate_schedule_admissible
ppt_pstate_schedule_admissible
Add dummy_double_array[3][DML2_MAX_PLANES] to
dml2_core_calcs_mode_support_locals.
Introduce dml2_core_utils_get_frame_time_us() in dml2_core_utils.c and export
it in dml2_core_utils.h to compute frame time in microseconds from stream
timing (vline time * (vactive + vblank)).
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
There are few non const input pointer fields. Setting them to const to
prevent future modification of read-only data.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
math_mod() multiplied by arg1 instead of arg2, returning a wrong
result for any non-trivial modulo operation.
[How]
Replace arg1 with arg2 in the subtraction term to correctly
implement fmod(arg1, arg2).
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Force overlay cursor mode when an underlying plane has a non-bypassed
color pipeline to avoid incorrect cursor transformation.
Reviewed-by: Sun peng (Leo) Li <sunpeng.li@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why] Implicit conversions from wider integer types to byte-sized fields
were generating compiler warnings. These warnings hide intentional protocol
/storage boundaries and reduce signal quality during builds. Making
conversion intent explicit improves readability and warning hygiene
without changing behavior.
[How] Added explicit, type-safe casts at intentional narrow-storage
boundaries. Kept data models & runtime logic unchanged, only clarifying
conversion intent.
Functionality and behavior is unchanged; only type intent is explicit.
Aligned warning cleanup with existing coding standards for explicit
boundary conversions.
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Gaghik Khachatrian <gaghik.khachatrian@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dc_destroy() sets dm->dc to NULL before amdgpu_dm_ism_fini() is called,
leaving a window where in-flight ISM delayed work dereferences the stale
pointer. Call amdgpu_dm_ism_fini() in amdgpu_dm_fini() before dc_destroy().
Fixes: 754003486c ("drm/amd/display: Add Idle state manager(ISM)")
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add missing description for do_mccs parameter in
amdgpu_dm_update_freesync_caps.
Fixes the below with gcc W=1:
../display/amdgpu_dm/amdgpu_dm.c:13269 function parameter 'do_mccs' not described in 'amdgpu_dm_update_freesync_caps'
Fixes: 8dc88c6a59 ("drm/amd/display: Avoid to do MCCS transaction if unnecessary")
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Wayne Lin <Wayne.Lin@amd.com>
Cc: Roman Li <roman.li@amd.com>
Cc: Alex Hung <alex.hung@amd.com>
Cc: Tom Chung <chiahsuan.chung@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The explicit include of linux/array_size.h in Display Core (DC) is
redundant. The ARRAY_SIZE macro is already provided by dm_services.h
(via os_types.h) which DC includes.
[How]
Remove the unnecessary #include <linux/array_size.h> from
dc_hw_sequencer.c and dce_clock_source.c.
Fixes: 2d23661764 ("drm/amd/display: Replace inline NUM_ELEMENTS macro with ARRAY_SIZE")
CC: Linus Probert <linus.probert@gmail.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along the following updates:
- Enable sink freesync via MCCS with pcon whitelist adjustments
- Rework YCbCr422 DSC policy
- Update DML2.1 parameters
- Fix coding style issues and compiler warnings
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Taimur Hassan <Syed.Hassan@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
