Add RGMII to supported interfaces for BCM63xx RGMII ports so they can be
actually used in RGMII mode.
Without this, phylink will fail to configure them:
[ 3.580000] b53-switch 10700000.switch GbE3 (uninitialized): validation of rgmii with support 0000000,00000000,00000000,000062ff and advertisement 0000000,00000000,00000000,000062ff failed: -EINVAL
[ 3.600000] b53-switch 10700000.switch GbE3 (uninitialized): failed to connect to PHY: -EINVAL
[ 3.610000] b53-switch 10700000.switch GbE3 (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 4
Fixes: ce3bf94871 ("net: dsa: b53: add support for BCM63xx RGMIIs")
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Link: https://patch.msgid.link/20250602193953.1010487-5-jonas.gorski@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The IMP port is not a valid RGMII interface, but hard wired to internal,
so we shouldn't touch the undefined register B53_RGMII_CTRL_IMP.
While this does not seem to have any side effects, let's not touch it at
all, so limit RGMII configuration on bcm63xx to the actual RGMII ports.
Fixes: ce3bf94871 ("net: dsa: b53: add support for BCM63xx RGMIIs")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250602193953.1010487-4-jonas.gorski@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
bcm63xx's RGMII ports are always in MAC mode, never in PHY mode, so we
shouldn't enable any delays and let the PHY handle any delays as
necessary.
This fixes using RGMII ports with normal PHYs like BCM54612E, which will
handle the delay in the PHY.
Fixes: ce3bf94871 ("net: dsa: b53: add support for BCM63xx RGMIIs")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250602193953.1010487-3-jonas.gorski@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
BCM63xx internal switches do not support EEE, but provide multiple RGMII
ports where external PHYs may be connected. If one of these PHYs are EEE
capable, we may try to enable EEE for the MACs, which then hangs the
system on access of the (non-existent) EEE registers.
Fix this by checking if the switch actually supports EEE before
attempting to configure it.
Fixes: 22256b0afb ("net: dsa: b53: Move EEE functions to b53")
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Tested-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Link: https://patch.msgid.link/20250602193953.1010487-2-jonas.gorski@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In MII mode, Tx lines are swapped for port0 and port1, which means
Tx port0 receives data from PRU1 and the Tx port1 receives data from
PRU0. This is an expected hardware behavior and reading the Tx stats
needs to be handled accordingly in the driver. Update the driver to
read Tx stats from the PRU1 for port0 and PRU0 for port1.
Fixes: c1e10d5dc7 ("net: ti: icssg-prueth: Add ICSSG Stats")
Signed-off-by: Meghana Malladi <m-malladi@ti.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250603052904.431203-1-m-malladi@ti.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
gve_alloc_pending_packet() can return NULL, but gve_tx_add_skb_dqo()
did not check for this case before dereferencing the returned pointer.
Add a missing NULL check to prevent a potential NULL pointer
dereference when allocation fails.
This improves robustness in low-memory scenarios.
Fixes: a57e5de476 ("gve: DQO: Add TX path")
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Reviewed-by: Mina Almasry <almasrymina@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lorenzo Bianconi says:
====================
net: airoha: Fix IPv6 hw acceleration
Fix IPv6 hw acceleration in bridge mode resolving ib2 and
airoha_foe_mac_info_common overwrite in
airoha_ppe_foe_commit_subflow_entry routine.
Introduce UPDMEM source-mac table used to set source mac address for
L3 IPv6 hw accelerated traffic.
====================
Link: https://patch.msgid.link/20250602-airoha-flowtable-ipv6-fix-v2-0-3287f8b55214@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Set PPE entry smac_id field to 0xf in airoha_ppe_foe_commit_subflow_entry
routine for IPv6 traffic in order to instruct the hw to keep original
source mac address for IPv6 hw accelerated traffic in bridge mode.
Fixes: cd53f62261 ("net: airoha: Add L2 hw acceleration support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250602-airoha-flowtable-ipv6-fix-v2-3-3287f8b55214@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
ib2 and airoha_foe_mac_info_common have not the same offsets in
airoha_foe_bridge and airoha_foe_ipv6 structures. Current codebase does
not accelerate IPv6 traffic in bridge mode since ib2 and l2 info are not
set properly copying airoha_foe_bridge struct into airoha_foe_ipv6 one
in airoha_ppe_foe_commit_subflow_entry routine.
Fix IPv6 hw acceleration in bridge mode resolving ib2 and
airoha_foe_mac_info_common overwrite in
airoha_ppe_foe_commit_subflow_entry() and configuring them with proper
values.
Fixes: cd53f62261 ("net: airoha: Add L2 hw acceleration support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250602-airoha-flowtable-ipv6-fix-v2-2-3287f8b55214@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
UPDMEM source-mac table is a key-value map used to store devices mac
addresses according to the port identifier. UPDMEM source mac table is
used during IPv6 traffic hw acceleration since PPE entries, for space
constraints, do not contain the full source mac address but just the
identifier in the UPDMEM source-mac table.
Configure UPDMEM source-mac table with device mac addresses and set
the source-mac ID field for PPE IPv6 entries in order to select the
proper device mac address as source mac for L3 IPv6 hw accelerated traffic.
Fixes: 00a7678310 ("net: airoha: Introduce flowtable offload support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250602-airoha-flowtable-ipv6-fix-v2-1-3287f8b55214@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
We have the logic to include net/lib automatically for net related
selftests. However, currently, this logic is only in install target
which means only `make install` will have net/lib included. This commit
adds the logic to all target so that all `make`, `make run_tests` and
`make install` will have net/lib included in net related selftests.
Signed-off-by: Bui Quang Minh <minhquangbui99@gmail.com>
Link: https://patch.msgid.link/20250601142914.13379-1-minhquangbui99@gmail.com
Fixes: b86761ff63 ("selftests: net: add scaffolding for Netlink tests in Python")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Commit 3d010c8031 ("udp: do not accept non-tunnel GSO skbs landing
in a tunnel") added checks in linux stack to not accept non-tunnel
GRO packets landing in a tunnel. This exposed an issue in vmxnet3
which was not correctly reporting GRO packets for tunnel packets.
This patch fixes this issue by setting correct GSO type for the
tunnel packets.
Currently, vmxnet3 does not support reporting inner fields for LRO
tunnel packets. The issue is not seen for egress drivers that do not
use skb inner fields. The workaround is to enable tnl-segmentation
offload on the egress interfaces if the driver supports it. This
problem pre-exists this patch fix and can be addressed as a separate
future patch.
Fixes: dacce2be33 ("vmxnet3: add geneve and vxlan tunnel offload support")
Signed-off-by: Ronak Doshi <ronak.doshi@broadcom.com>
Acked-by: Guolin Yang <guolin.yang@broadcom.com>
Link: https://patch.msgid.link/20250530152701.70354-1-ronak.doshi@broadcom.com
[pabeni@redhat.com: dropped the changelog]
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This reverts commit a571a9a1b1.
The commit in question breaks kunit for older compilers:
$ gcc --version
gcc (GCC) 11.5.0 20240719 (Red Hat 11.5.0-5)
$ ./tools/testing/kunit/kunit.py run --alltests --json --arch=x86_64
Configuring KUnit Kernel ...
Regenerating .config ...
Populating config with:
$ make ARCH=x86_64 O=.kunit olddefconfig
ERROR:root:Not all Kconfig options selected in kunitconfig were in the generated .config.
This is probably due to unsatisfied dependencies.
Missing: CONFIG_INIT_STACK_ALL_PATTERN=y
Link: https://lore.kernel.org/20250529083811.778bc31b@kernel.org
Fixes: a571a9a1b1 ("kunit: configs: Enable CONFIG_INIT_STACK_ALL_PATTERN in all_tests")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://patch.msgid.link/20250530135800.13437-1-kuba@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When driver handles the napi rx polling requests, the netdev might
have been released by the dellink logic triggered by the disconnect
operation on user plane. However, in the logic of processing skb in
polling, an invalid netdev is still being used, which causes a panic.
BUG: kernel NULL pointer dereference, address: 00000000000000f1
Oops: 0000 [#1] PREEMPT SMP NOPTI
RIP: 0010:dev_gro_receive+0x3a/0x620
[...]
Call Trace:
<IRQ>
? __die_body+0x68/0xb0
? page_fault_oops+0x379/0x3e0
? exc_page_fault+0x4f/0xa0
? asm_exc_page_fault+0x22/0x30
? __pfx_t7xx_ccmni_recv_skb+0x10/0x10 [mtk_t7xx (HASH:1400 7)]
? dev_gro_receive+0x3a/0x620
napi_gro_receive+0xad/0x170
t7xx_ccmni_recv_skb+0x48/0x70 [mtk_t7xx (HASH:1400 7)]
t7xx_dpmaif_napi_rx_poll+0x590/0x800 [mtk_t7xx (HASH:1400 7)]
net_rx_action+0x103/0x470
irq_exit_rcu+0x13a/0x310
sysvec_apic_timer_interrupt+0x56/0x90
</IRQ>
Fixes: 5545b7b9f2 ("net: wwan: t7xx: Add NAPI support")
Signed-off-by: Jinjian Song <jinjian.song@fibocom.com>
Link: https://patch.msgid.link/20250530031648.5592-1-jinjian.song@fibocom.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2025-05-30 (ice, idpf)
For ice:
Michal resolves XDP issues related to Tx scheduler configuration with
large number of Tx queues.
Additional information:
https://lore.kernel.org/intel-wired-lan/20250513105529.241745-1-michal.kubiak@intel.com/
For idpf:
Brian Vazquez updates netif_subqueue_maybe_stop() condition check to
prevent possible races.
Emil shuts down virtchannel mailbox during reset to reduce timeout
delays as it's unavailable during that time.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
idpf: avoid mailbox timeout delays during reset
idpf: fix a race in txq wakeup
ice: fix rebuilding the Tx scheduler tree for large queue counts
ice: create new Tx scheduler nodes for new queues only
ice: fix Tx scheduler error handling in XDP callback
====================
Link: https://patch.msgid.link/20250530211221.2170484-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit a1e40ac5b5 ("net: gso: fix udp gso fraglist segmentation after
pull from frag_list") detected invalid geometry in frag_list skbs and
redirects them from skb_segment_list to more robust skb_segment. But some
packets with modified geometry can also hit bugs in that code. We don't
know how many such cases exist. Addressing each one by one also requires
touching the complex skb_segment code, which risks introducing bugs for
other types of skbs. Instead, linearize all these packets that fail the
basic invariants on gso fraglist skbs. That is more robust.
If only part of the fraglist payload is pulled into head_skb, it will
always cause exception when splitting skbs by skb_segment. For detailed
call stack information, see below.
Valid SKB_GSO_FRAGLIST skbs
- consist of two or more segments
- the head_skb holds the protocol headers plus first gso_size
- one or more frag_list skbs hold exactly one segment
- all but the last must be gso_size
Optional datapath hooks such as NAT and BPF (bpf_skb_pull_data) can
modify fraglist skbs, breaking these invariants.
In extreme cases they pull one part of data into skb linear. For UDP,
this causes three payloads with lengths of (11,11,10) bytes were
pulled tail to become (12,10,10) bytes.
The skbs no longer meets the above SKB_GSO_FRAGLIST conditions because
payload was pulled into head_skb, it needs to be linearized before pass
to regular skb_segment.
skb_segment+0xcd0/0xd14
__udp_gso_segment+0x334/0x5f4
udp4_ufo_fragment+0x118/0x15c
inet_gso_segment+0x164/0x338
skb_mac_gso_segment+0xc4/0x13c
__skb_gso_segment+0xc4/0x124
validate_xmit_skb+0x9c/0x2c0
validate_xmit_skb_list+0x4c/0x80
sch_direct_xmit+0x70/0x404
__dev_queue_xmit+0x64c/0xe5c
neigh_resolve_output+0x178/0x1c4
ip_finish_output2+0x37c/0x47c
__ip_finish_output+0x194/0x240
ip_finish_output+0x20/0xf4
ip_output+0x100/0x1a0
NF_HOOK+0xc4/0x16c
ip_forward+0x314/0x32c
ip_rcv+0x90/0x118
__netif_receive_skb+0x74/0x124
process_backlog+0xe8/0x1a4
__napi_poll+0x5c/0x1f8
net_rx_action+0x154/0x314
handle_softirqs+0x154/0x4b8
[118.376811] [C201134] rxq0_pus: [name:bug&]kernel BUG at net/core/skbuff.c:4278!
[118.376829] [C201134] rxq0_pus: [name:traps&]Internal error: Oops - BUG: 00000000f2000800 [#1] PREEMPT SMP
[118.470774] [C201134] rxq0_pus: [name:mrdump&]Kernel Offset: 0x178cc00000 from 0xffffffc008000000
[118.470810] [C201134] rxq0_pus: [name:mrdump&]PHYS_OFFSET: 0x40000000
[118.470827] [C201134] rxq0_pus: [name:mrdump&]pstate: 60400005 (nZCv daif +PAN -UAO)
[118.470848] [C201134] rxq0_pus: [name:mrdump&]pc : [0xffffffd79598aefc] skb_segment+0xcd0/0xd14
[118.470900] [C201134] rxq0_pus: [name:mrdump&]lr : [0xffffffd79598a5e8] skb_segment+0x3bc/0xd14
[118.470928] [C201134] rxq0_pus: [name:mrdump&]sp : ffffffc008013770
Fixes: a1e40ac5b5 ("gso: fix udp gso fraglist segmentation after pull from frag_list")
Signed-off-by: Shiming Cheng <shiming.cheng@mediatek.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Chaignon says:
====================
net: Fix inet_proto_csum_replace_by_diff for IPv6
This patchset fixes a bug that causes skb->csum to hold an incorrect
value when calling inet_proto_csum_replace_by_diff for an IPv6 packet
in CHECKSUM_COMPLETE state. This bug affects BPF helper
bpf_l4_csum_replace and IPv6 ILA in adj-transport mode.
In those cases, inet_proto_csum_replace_by_diff updates the L4 checksum
field after an IPv6 address change. These two changes cancel each other
in terms of checksum, so skb->csum shouldn't be updated.
v2: https://lore.kernel.org/aCz84JU60wd8etiT@mail.gmail.com
====================
Link: https://patch.msgid.link/cover.1748509484.git.paul.chaignon@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In Cilium, we use bpf_csum_diff + bpf_l4_csum_replace to, among other
things, update the L4 checksum after reverse SNATing IPv6 packets. That
use case is however not currently supported and leads to invalid
skb->csum values in some cases. This patch adds support for IPv6 address
changes in bpf_l4_csum_update via a new flag.
When calling bpf_l4_csum_replace in Cilium, it ends up calling
inet_proto_csum_replace_by_diff:
1: void inet_proto_csum_replace_by_diff(__sum16 *sum, struct sk_buff *skb,
2: __wsum diff, bool pseudohdr)
3: {
4: if (skb->ip_summed != CHECKSUM_PARTIAL) {
5: csum_replace_by_diff(sum, diff);
6: if (skb->ip_summed == CHECKSUM_COMPLETE && pseudohdr)
7: skb->csum = ~csum_sub(diff, skb->csum);
8: } else if (pseudohdr) {
9: *sum = ~csum_fold(csum_add(diff, csum_unfold(*sum)));
10: }
11: }
The bug happens when we're in the CHECKSUM_COMPLETE state. We've just
updated one of the IPv6 addresses. The helper now updates the L4 header
checksum on line 5. Next, it updates skb->csum on line 7. It shouldn't.
For an IPv6 packet, the updates of the IPv6 address and of the L4
checksum will cancel each other. The checksums are set such that
computing a checksum over the packet including its checksum will result
in a sum of 0. So the same is true here when we update the L4 checksum
on line 5. We'll update it as to cancel the previous IPv6 address
update. Hence skb->csum should remain untouched in this case.
The same bug doesn't affect IPv4 packets because, in that case, three
fields are updated: the IPv4 address, the IP checksum, and the L4
checksum. The change to the IPv4 address and one of the checksums still
cancel each other in skb->csum, but we're left with one checksum update
and should therefore update skb->csum accordingly. That's exactly what
inet_proto_csum_replace_by_diff does.
This special case for IPv6 L4 checksums is also described atop
inet_proto_csum_replace16, the function we should be using in this case.
This patch introduces a new bpf_l4_csum_replace flag, BPF_F_IPV6,
to indicate that we're updating the L4 checksum of an IPv6 packet. When
the flag is set, inet_proto_csum_replace_by_diff will skip the
skb->csum update.
Fixes: 7d672345ed ("bpf: add generic bpf_csum_diff helper")
Signed-off-by: Paul Chaignon <paul.chaignon@gmail.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://patch.msgid.link/96a6bc3a443e6f0b21ff7b7834000e17fb549e05.1748509484.git.paul.chaignon@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
During ILA address translations, the L4 checksums can be handled in
different ways. One of them, adj-transport, consist in parsing the
transport layer and updating any found checksum. This logic relies on
inet_proto_csum_replace_by_diff and produces an incorrect skb->csum when
in state CHECKSUM_COMPLETE.
This bug can be reproduced with a simple ILA to SIR mapping, assuming
packets are received with CHECKSUM_COMPLETE:
$ ip a show dev eth0
14: eth0@if15: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000
link/ether 62:ae:35:9e:0f:8d brd ff:ff:ff:ff:ff:ff link-netnsid 0
inet6 3333:0:0:1::c078/64 scope global
valid_lft forever preferred_lft forever
inet6 fd00:10:244:1::c078/128 scope global nodad
valid_lft forever preferred_lft forever
inet6 fe80::60ae:35ff:fe9e:f8d/64 scope link proto kernel_ll
valid_lft forever preferred_lft forever
$ ip ila add loc_match fd00:10:244:1 loc 3333:0:0:1 \
csum-mode adj-transport ident-type luid dev eth0
Then I hit [fd00:10:244:1::c078]:8000 with a server listening only on
[3333:0:0:1::c078]:8000. With the bug, the SYN packet is dropped with
SKB_DROP_REASON_TCP_CSUM after inet_proto_csum_replace_by_diff changed
skb->csum. The translation and drop are visible on pwru [1] traces:
IFACE TUPLE FUNC
eth0:9 [fd00:10:244:3::3d8]:51420->[fd00:10:244:1::c078]:8000(tcp) ipv6_rcv
eth0:9 [fd00:10:244:3::3d8]:51420->[fd00:10:244:1::c078]:8000(tcp) ip6_rcv_core
eth0:9 [fd00:10:244:3::3d8]:51420->[fd00:10:244:1::c078]:8000(tcp) nf_hook_slow
eth0:9 [fd00:10:244:3::3d8]:51420->[fd00:10:244:1::c078]:8000(tcp) inet_proto_csum_replace_by_diff
eth0:9 [fd00:10:244:3::3d8]:51420->[3333:0:0:1::c078]:8000(tcp) tcp_v6_early_demux
eth0:9 [fd00:10:244:3::3d8]:51420->[3333:0:0:1::c078]:8000(tcp) ip6_route_input
eth0:9 [fd00:10:244:3::3d8]:51420->[3333:0:0:1::c078]:8000(tcp) ip6_input
eth0:9 [fd00:10:244:3::3d8]:51420->[3333:0:0:1::c078]:8000(tcp) ip6_input_finish
eth0:9 [fd00:10:244:3::3d8]:51420->[3333:0:0:1::c078]:8000(tcp) ip6_protocol_deliver_rcu
eth0:9 [fd00:10:244:3::3d8]:51420->[3333:0:0:1::c078]:8000(tcp) raw6_local_deliver
eth0:9 [fd00:10:244:3::3d8]:51420->[3333:0:0:1::c078]:8000(tcp) ipv6_raw_deliver
eth0:9 [fd00:10:244:3::3d8]:51420->[3333:0:0:1::c078]:8000(tcp) tcp_v6_rcv
eth0:9 [fd00:10:244:3::3d8]:51420->[3333:0:0:1::c078]:8000(tcp) __skb_checksum_complete
eth0:9 [fd00:10:244:3::3d8]:51420->[3333:0:0:1::c078]:8000(tcp) kfree_skb_reason(SKB_DROP_REASON_TCP_CSUM)
eth0:9 [fd00:10:244:3::3d8]:51420->[3333:0:0:1::c078]:8000(tcp) skb_release_head_state
eth0:9 [fd00:10:244:3::3d8]:51420->[3333:0:0:1::c078]:8000(tcp) skb_release_data
eth0:9 [fd00:10:244:3::3d8]:51420->[3333:0:0:1::c078]:8000(tcp) skb_free_head
eth0:9 [fd00:10:244:3::3d8]:51420->[3333:0:0:1::c078]:8000(tcp) kfree_skbmem
This is happening because inet_proto_csum_replace_by_diff is updating
skb->csum when it shouldn't. The L4 checksum is updated such that it
"cancels" the IPv6 address change in terms of checksum computation, so
the impact on skb->csum is null.
Note this would be different for an IPv4 packet since three fields
would be updated: the IPv4 address, the IP checksum, and the L4
checksum. Two would cancel each other and skb->csum would still need
to be updated to take the L4 checksum change into account.
This patch fixes it by passing an ipv6 flag to
inet_proto_csum_replace_by_diff, to skip the skb->csum update if we're
in the IPv6 case. Note the behavior of the only other user of
inet_proto_csum_replace_by_diff, the BPF subsystem, is left as is in
this patch and fixed in the subsequent patch.
With the fix, using the reproduction from above, I can confirm
skb->csum is not touched by inet_proto_csum_replace_by_diff and the TCP
SYN proceeds to the application after the ILA translation.
Link: https://github.com/cilium/pwru [1]
Fixes: 65d7ab8de5 ("net: Identifier Locator Addressing module")
Signed-off-by: Paul Chaignon <paul.chaignon@gmail.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://patch.msgid.link/b5539869e3550d46068504feb02d37653d939c0b.1748509484.git.paul.chaignon@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If the ptp_rate recorded earlier in the driver happens to be 0, this
bogus value will propagate up to EST configuration, where it will
trigger a division by 0.
Prevent this division by 0 by adding the corresponding check and error
code.
Suggested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Fixes: 8572aec3d0 ("net: stmmac: Add basic EST support for XGMAC")
Link: https://patch.msgid.link/20250529-stmmac_tstamp_div-v4-2-d73340a794d5@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The stmmac platform drivers that do not open-code the clk_ptp_rate value
after having retrieved the default one from the device-tree can end up
with 0 in clk_ptp_rate (as clk_get_rate can return 0). It will
eventually propagate up to PTP initialization when bringing up the
interface, leading to a divide by 0:
Division by zero in kernel.
CPU: 1 UID: 0 PID: 1 Comm: swapper/0 Not tainted 6.12.30-00001-g48313bd5768a #22
Hardware name: STM32 (Device Tree Support)
Call trace:
unwind_backtrace from show_stack+0x18/0x1c
show_stack from dump_stack_lvl+0x6c/0x8c
dump_stack_lvl from Ldiv0_64+0x8/0x18
Ldiv0_64 from stmmac_init_tstamp_counter+0x190/0x1a4
stmmac_init_tstamp_counter from stmmac_hw_setup+0xc1c/0x111c
stmmac_hw_setup from __stmmac_open+0x18c/0x434
__stmmac_open from stmmac_open+0x3c/0xbc
stmmac_open from __dev_open+0xf4/0x1ac
__dev_open from __dev_change_flags+0x1cc/0x224
__dev_change_flags from dev_change_flags+0x24/0x60
dev_change_flags from ip_auto_config+0x2e8/0x11a0
ip_auto_config from do_one_initcall+0x84/0x33c
do_one_initcall from kernel_init_freeable+0x1b8/0x214
kernel_init_freeable from kernel_init+0x24/0x140
kernel_init from ret_from_fork+0x14/0x28
Exception stack(0xe0815fb0 to 0xe0815ff8)
Prevent this division by 0 by adding an explicit check and error log
about the actual issue. While at it, remove the same check from
stmmac_ptp_register, which then becomes duplicate
Fixes: 19d857c903 ("stmmac: Fix calculations for ptp counters when clock input = 50Mhz.")
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Yanteng Si <si.yanteng@linux.dev>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250529-stmmac_tstamp_div-v4-1-d73340a794d5@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The MANA driver's probe registers netdevice via the following call chain:
mana_probe()
register_netdev()
register_netdevice()
register_netdevice() calls notifier callback for netvsc driver,
holding the netdev mutex via netdev_lock_ops().
Further this netvsc notifier callback end up attempting to acquire the
same lock again in dev_xdp_propagate() leading to deadlock.
netvsc_netdev_event()
netvsc_vf_setxdp()
dev_xdp_propagate()
This deadlock was not observed so far because net_shaper_ops was never set,
and thus the lock was effectively a no-op in this case. Fix this by using
netif_xdp_propagate() instead of dev_xdp_propagate() to avoid recursive
locking in this path.
And, since no deadlock is observed on the other path which is via
netvsc_probe, add the lock exclusivly for that path.
Also, clean up the unregistration path by removing the unnecessary call to
netvsc_vf_setxdp(), since unregister_netdevice_many_notify() already
performs this cleanup via dev_xdp_uninstall().
Fixes: 97246d6d21 ("net: hold netdev instance lock during ndo_bpf")
Cc: stable@vger.kernel.org
Signed-off-by: Saurabh Sengar <ssengar@linux.microsoft.com>
Tested-by: Erni Sri Satya Vennela <ernis@linux.microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Subbaraya Sundeep <sbhatta@marvell.com>
Link: https://patch.msgid.link/1748513910-23963-1-git-send-email-ssengar@linux.microsoft.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix the signature of the net_devmem_bind_dmabuf API for
CONFIG_NET_DEVMEM=n.
Fixes: bd61848900 ("net: devmem: Implement TX path")
Signed-off-by: Pranjal Shrivastava <praan@google.com>
Link: https://patch.msgid.link/20250528211058.1826608-1-praan@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
BRCM_LEG_PORT_ID was incorrectly used for pskb_may_pull length.
The correct check is BRCM_LEG_TAG_LEN + VLAN_HLEN, or 10 bytes.
Fixes: 964dbf186e ("net: dsa: tag_brcm: add support for legacy tags")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250529124406.2513779-1-noltari@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
- hci_qca: move the SoC type check to the right place
- MGMT: reject malformed HCI_CMD_SYNC commands
- btnxpuart: Fix missing devm_request_irq() return value check
- L2CAP: Fix not responding with L2CAP_CR_LE_ENCRYPTION
-----BEGIN PGP SIGNATURE-----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=cEYF
-----END PGP SIGNATURE-----
Merge tag 'for-net-2025-05-30' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
Luiz Augusto von Dentz says:
====================
bluetooth pull request for net:
- hci_qca: move the SoC type check to the right place
- MGMT: reject malformed HCI_CMD_SYNC commands
- btnxpuart: Fix missing devm_request_irq() return value check
- L2CAP: Fix not responding with L2CAP_CR_LE_ENCRYPTION
* tag 'for-net-2025-05-30' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth:
Bluetooth: L2CAP: Fix not responding with L2CAP_CR_LE_ENCRYPTION
Bluetooth: hci_qca: move the SoC type check to the right place
Bluetooth: btnxpuart: Fix missing devm_request_irq() return value check
Bluetooth: MGMT: reject malformed HCI_CMD_SYNC commands
====================
Link: https://patch.msgid.link/20250530174835.405726-1-luiz.dentz@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Mailbox operations are not possible while the driver is in reset.
Operations that require MBX exchange with the control plane will result
in long delays if executed while a reset is in progress:
ethtool -L <inf> combined 8& echo 1 > /sys/class/net/<inf>/device/reset
idpf 0000:83:00.0: HW reset detected
idpf 0000:83:00.0: Device HW Reset initiated
idpf 0000:83:00.0: Transaction timed-out (op:504 cookie:be00 vc_op:504 salt:be timeout:2000ms)
idpf 0000:83:00.0: Transaction timed-out (op:508 cookie:bf00 vc_op:508 salt:bf timeout:2000ms)
idpf 0000:83:00.0: Transaction timed-out (op:512 cookie:c000 vc_op:512 salt:c0 timeout:2000ms)
idpf 0000:83:00.0: Transaction timed-out (op:510 cookie:c100 vc_op:510 salt:c1 timeout:2000ms)
idpf 0000:83:00.0: Transaction timed-out (op:509 cookie:c200 vc_op:509 salt:c2 timeout:60000ms)
idpf 0000:83:00.0: Transaction timed-out (op:509 cookie:c300 vc_op:509 salt:c3 timeout:60000ms)
idpf 0000:83:00.0: Transaction timed-out (op:505 cookie:c400 vc_op:505 salt:c4 timeout:60000ms)
idpf 0000:83:00.0: Failed to configure queues for vport 0, -62
Disable mailbox communication in case of a reset, unless it's done during
a driver load, where the virtchnl operations are needed to configure the
device.
Fixes: 8077c72756 ("idpf: add controlq init and reset checks")
Co-developed-by: Joshua Hay <joshua.a.hay@intel.com>
Signed-off-by: Joshua Hay <joshua.a.hay@intel.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Reviewed-by: Ahmed Zaki <ahmed.zaki@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add a helper function to correctly handle the lockless
synchronization when the sender needs to block. The paradigm is
if (no_resources()) {
stop_queue();
barrier();
if (!no_resources())
restart_queue();
}
netif_subqueue_maybe_stop already handles the paradigm correctly, but
the code split the check for resources in three parts, the first one
(descriptors) followed the protocol, but the other two (completions and
tx_buf) were only doing the first part and so race prone.
Luckily netif_subqueue_maybe_stop macro already allows you to use a
function to evaluate the start/stop conditions so the fix only requires
the right helper function to evaluate all the conditions at once.
The patch removes idpf_tx_maybe_stop_common since it's no longer needed
and instead adjusts separately the conditions for singleq and splitq.
Note that idpf_tx_buf_hw_update doesn't need to check for resources
since that will be covered in idpf_tx_splitq_frame.
To reproduce:
Reduce the threshold for pending completions to increase the chances of
hitting this pause by changing your kernel:
drivers/net/ethernet/intel/idpf/idpf_txrx.h
-#define IDPF_TX_COMPLQ_OVERFLOW_THRESH(txcq) ((txcq)->desc_count >> 1)
+#define IDPF_TX_COMPLQ_OVERFLOW_THRESH(txcq) ((txcq)->desc_count >> 4)
Use pktgen to force the host to push small pkts very aggressively:
./pktgen_sample02_multiqueue.sh -i eth1 -s 100 -6 -d $IP -m $MAC \
-p 10000-10000 -t 16 -n 0 -v -x -c 64
Fixes: 6818c4d5b3 ("idpf: add splitq start_xmit")
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Madhu Chittim <madhu.chittim@intel.com>
Signed-off-by: Josh Hay <joshua.a.hay@intel.com>
Signed-off-by: Brian Vazquez <brianvv@google.com>
Signed-off-by: Luigi Rizzo <lrizzo@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The current implementation of the Tx scheduler allows the tree to be
rebuilt as the user adds more Tx queues to the VSI. In such a case,
additional child nodes are added to the tree to support the new number
of queues.
Unfortunately, this algorithm does not take into account that the limit
of the VSI support node may be exceeded, so an additional node in the
VSI layer may be required to handle all the requested queues.
Such a scenario occurs when adding XDP Tx queues on machines with many
CPUs. Although the driver still respects the queue limit returned by
the FW, the Tx scheduler was unable to add those queues to its tree
and returned one of the errors below.
Such a scenario occurs when adding XDP Tx queues on machines with many
CPUs (e.g. at least 321 CPUs, if there is already 128 Tx/Rx queue pairs).
Although the driver still respects the queue limit returned by the FW,
the Tx scheduler was unable to add those queues to its tree and returned
the following errors:
Failed VSI LAN queue config for XDP, error: -5
or:
Failed to set LAN Tx queue context, error: -22
Fix this problem by extending the tree rebuild algorithm to check if the
current VSI node can support the requested number of queues. If it
cannot, create as many additional VSI support nodes as necessary to
handle all the required Tx queues. Symmetrically, adjust the VSI node
removal algorithm to remove all nodes associated with the given VSI.
Also, make the search for the next free VSI node more restrictive. That is,
add queue group nodes only to the VSI support nodes that have a matching
VSI handle.
Finally, fix the comment describing the tree update algorithm to better
reflect the current scenario.
Fixes: b0153fdd7e ("ice: update VSI config dynamically")
Reviewed-by: Dawid Osuchowski <dawid.osuchowski@linux.intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Michal Kubiak <michal.kubiak@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Jesse Brandeburg <jbrandeburg@cloudflare.com>
Tested-by: Saritha Sanigani <sarithax.sanigani@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The current implementation of the Tx scheduler tree attempts
to create nodes for all Tx queues, ignoring the fact that some
queues may already exist in the tree. For example, if the VSI
already has 128 Tx queues and the user requests for 16 new queues,
the Tx scheduler will compute the tree for 272 queues (128 existing
queues + 144 new queues), instead of 144 queues (128 existing queues
and 16 new queues).
Fix that by modifying the node count calculation algorithm to skip
the queues that already exist in the tree.
Fixes: 5513b920a4 ("ice: Update Tx scheduler tree for VSI multi-Tx queue support")
Reviewed-by: Dawid Osuchowski <dawid.osuchowski@linux.intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Michal Kubiak <michal.kubiak@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Jesse Brandeburg <jbrandeburg@cloudflare.com>
Tested-by: Saritha Sanigani <sarithax.sanigani@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When the XDP program is loaded, the XDP callback adds new Tx queues.
This means that the callback must update the Tx scheduler with the new
queue number. In the event of a Tx scheduler failure, the XDP callback
should also fail and roll back any changes previously made for XDP
preparation.
The previous implementation had a bug that not all changes made by the
XDP callback were rolled back. This caused the crash with the following
call trace:
[ +9.549584] ice 0000:ca:00.0: Failed VSI LAN queue config for XDP, error: -5
[ +0.382335] Oops: general protection fault, probably for non-canonical address 0x50a2250a90495525: 0000 [#1] SMP NOPTI
[ +0.010710] CPU: 103 UID: 0 PID: 0 Comm: swapper/103 Not tainted 6.14.0-net-next-mar-31+ #14 PREEMPT(voluntary)
[ +0.010175] Hardware name: Intel Corporation M50CYP2SBSTD/M50CYP2SBSTD, BIOS SE5C620.86B.01.01.0005.2202160810 02/16/2022
[ +0.010946] RIP: 0010:__ice_update_sample+0x39/0xe0 [ice]
[...]
[ +0.002715] Call Trace:
[ +0.002452] <IRQ>
[ +0.002021] ? __die_body.cold+0x19/0x29
[ +0.003922] ? die_addr+0x3c/0x60
[ +0.003319] ? exc_general_protection+0x17c/0x400
[ +0.004707] ? asm_exc_general_protection+0x26/0x30
[ +0.004879] ? __ice_update_sample+0x39/0xe0 [ice]
[ +0.004835] ice_napi_poll+0x665/0x680 [ice]
[ +0.004320] __napi_poll+0x28/0x190
[ +0.003500] net_rx_action+0x198/0x360
[ +0.003752] ? update_rq_clock+0x39/0x220
[ +0.004013] handle_softirqs+0xf1/0x340
[ +0.003840] ? sched_clock_cpu+0xf/0x1f0
[ +0.003925] __irq_exit_rcu+0xc2/0xe0
[ +0.003665] common_interrupt+0x85/0xa0
[ +0.003839] </IRQ>
[ +0.002098] <TASK>
[ +0.002106] asm_common_interrupt+0x26/0x40
[ +0.004184] RIP: 0010:cpuidle_enter_state+0xd3/0x690
Fix this by performing the missing unmapping of XDP queues from
q_vectors and setting the XDP rings pointer back to NULL after all those
queues are released.
Also, add an immediate exit from the XDP callback in case of ring
preparation failure.
Fixes: efc2214b60 ("ice: Add support for XDP")
Reviewed-by: Dawid Osuchowski <dawid.osuchowski@linux.intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Michal Kubiak <michal.kubiak@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Jesse Brandeburg <jbrandeburg@cloudflare.com>
Tested-by: Saritha Sanigani <sarithax.sanigani@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Depending on the security set the response to L2CAP_LE_CONN_REQ shall be
just L2CAP_CR_LE_ENCRYPTION if only encryption when BT_SECURITY_MEDIUM
is selected since that means security mode 2 which doesn't require
authentication which is something that is covered in the qualification
test L2CAP/LE/CFC/BV-25-C.
Link: https://github.com/bluez/bluez/issues/1270
Fixes: 27e2d4c8d2 ("Bluetooth: Add basic LE L2CAP connect request receiving support")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Commit 3d05fc8223 ("Bluetooth: qca: set power_ctrl_enabled on NULL
returned by gpiod_get_optional()") accidentally changed the prevous
behavior where power control would be disabled without the BT_EN GPIO
only on QCA_WCN6750 and QCA_WCN6855 while also getting the error check
wrong. We should treat every IS_ERR() return value from
devm_gpiod_get_optional() as a reason to bail-out while we should only
set power_ctrl_enabled to false on the two models mentioned above. While
at it: use dev_err_probe() to save a LOC.
Cc: stable@vger.kernel.org
Fixes: 3d05fc8223 ("Bluetooth: qca: set power_ctrl_enabled on NULL returned by gpiod_get_optional()")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Hsin-chen Chuang <chharry@chromium.org>
Reviewed-by: Hsin-chen Chuang <chharry@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Return value of devm_request_irq() must be checked (function is even
annotated) and without it clang W=1 complains:
btnxpuart.c:494:6: error: unused variable 'ret' [-Werror,-Wunused-variable]
Setting up wakeup IRQ handler is not really critical, because the
handler is empty, so just log the informational message so user could
submit proper bug report and silences the clang warning.
Fixes: c50b56664e ("Bluetooth: btnxpuart: Implement host-wakeup feature")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
In 'mgmt_hci_cmd_sync()', check whether the size of parameters passed
in 'struct mgmt_cp_hci_cmd_sync' matches the total size of the data
(i.e. 'sizeof(struct mgmt_cp_hci_cmd_sync)' plus trailing bytes).
Otherwise, large invalid 'params_len' will cause 'hci_cmd_sync_alloc()'
to do 'skb_put_data()' from an area beyond the one actually passed to
'mgmt_hci_cmd_sync()'.
Reported-by: syzbot+5fe2d5bfbfbec0b675a0@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=5fe2d5bfbfbec0b675a0
Fixes: 827af4787e ("Bluetooth: MGMT: Add initial implementation of MGMT_OP_HCI_CMD_SYNC")
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
If we sanitize error returns, the debug statements need
to come before that so that we don't lose information.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Fixes: 405b0d6107 ("net: usb: aqc111: fix error handling of usbnet read calls")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running these commands on DUT (and similar at the other end)
ip link set dev eth0 up
ip link add link eth0 name eth0.10 type vlan id 10
ip addr add 10.0.0.1/24 dev eth0.10
ip link set dev eth0.10 up
ping 10.0.0.2
The ping will fail.
The reason why is failing is because, the network interfaces for lan966x
have a flag saying that the HW can insert the vlan tags into the
frames(NETIF_F_HW_VLAN_CTAG_TX). Meaning that the frames that are
transmitted don't have the vlan tag inside the skb data, but they have
it inside the skb. We already get that vlan tag and put it in the IFH
but the problem is that we don't configure the HW to rewrite the frame
when the interface is in host mode.
The fix consists in actually configuring the HW to insert the vlan tag
if it is different than 0.
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Fixes: 6d2c186afa ("net: lan966x: Add vlan support.")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://patch.msgid.link/20250528093619.3738998-1-horatiu.vultur@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEn/sM2K9nqF/8FWzzDHRl3/mQkZwFAmg4EQYTHG1rbEBwZW5n
dXRyb25peC5kZQAKCRAMdGXf+ZCRnH+1B/9pz2ikt785grwkWb0edC/avyQDDcYN
oY6FqYUUbQhQeoLWNWIAjyCzgoUx7fM+rpjsqQrZQeyfX3tPDepWMNS5MxuUPJHD
14uY5p0Ii6KrJkDYQ8Ft6hr5DVhcqHoJPqc1YJX3MZm8fBIsJ8kzkUbjtL0x91Ty
dfqaT9ai1MrOVgjS5OED2G+93sBGMdw/AIe8ftfnxGx0ax4CWB/jhk8waQuwfJwm
yldsbbh337/Vt6/0ZusAdEExupJaP/RHEcSQIg6zAmTH/v3bLmXNYvXPg3rY/4tL
B7oE/w1RDWPdYkaJZeM2NBsE3VONCGCi1qxlilzBH8xHZ8kHojrl6nBI
=ArZE
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-6.16-20250529' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2025-05-29
this is a pull request of 1 patch for net/main.
The patch is by Fedor Pchelkin and fixes a slab-out-of-bounds access
in the kvaser_pciefd driver.
linux-can-fixes-for-6.16-20250529
* tag 'linux-can-fixes-for-6.16-20250529' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: kvaser_pciefd: refine error prone echo_skb_max handling logic
====================
Link: https://patch.msgid.link/20250529075313.1101820-1-mkl@pengutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The "freq" variable is in terms of MHz and "max_val_cycles" is in terms
of Hz. The fact that "max_val_cycles" is a u64 suggests that support
for high frequency is intended but the "freq_khz * 1000" would overflow
the u32 type if we went above 4GHz. Use unsigned long long type for the
mutliplication to prevent that.
Fixes: 31c128b66e ("net/mlx4_en: Choose time-stamping shift value according to HW frequency")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/aDbFHe19juIJKjsb@stanley.mountain
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Identify the cause of the suspend/resume hang: netif_carrier_off()
is called during link state changes and becomes stuck while
executing linkwatch_work().
To resolve this issue, call netif_device_detach() during the Ethernet
suspend process to temporarily detach the network device from the
kernel and prevent the suspend/resume hang.
Fixes: 8c7bd5a454 ("net: ethernet: mtk-star-emac: new driver")
Signed-off-by: Yanqing Wang <ot_yanqing.wang@mediatek.com>
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Link: https://patch.msgid.link/20250528075351.593068-1-macpaul.lin@mediatek.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Fix the return value of none_validate_challenge() to be explicitly true
(which indicates the source packet should simply be discarded) rather than
implicitly true (because rxrpc_abort_conn() always returns -EPROTO which
gets converted to true).
Note that this change doesn't change the behaviour of the code (which is
correct by accident) and, in any case, we *shouldn't* get a CHALLENGE
packet to an rxnull connection (ie. no security).
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lists.infradead.org/pipermail/linux-afs/2025-April/009738.html
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: Jakub Kicinski <kuba@kernel.org>
cc: "David S. Miller" <davem@davemloft.net>
cc: Eric Dumazet <edumazet@google.com>
cc: Paolo Abeni <pabeni@redhat.com>
cc: Simon Horman <horms@kernel.org>
cc: linux-afs@lists.infradead.org
cc: netdev@vger.kernel.org
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/10720.1748358103@warthog.procyon.org.uk
Fixes: 5800b1cf3f ("rxrpc: Allow CHALLENGEs to the passed to the app for a RESPONSE")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Previously, the RX_BUFFERS_POSTED stat incorrectly reported the
fill_cnt from RX queue 0 for all queues, resulting in inaccurate
per-queue statistics.
Fix this by correctly indexing priv->rx[idx].fill_cnt for each RX queue.
Fixes: 24aeb56f2d ("gve: Add Gvnic stats AQ command and ethtool show/set-priv-flags.")
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Link: https://patch.msgid.link/20250527130830.1812903-1-alok.a.tiwari@oracle.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
bus_id is currently derived from the ethernetX alias. If one is missing
for the device, 0 is used. If ethernet0 points to another stmmac device
or if there are 2+ stmmac devices without an ethernet alias, then bus_id
will be 0 for all of those.
This is an issue because the bus_id is used to generate the mdio bus id
(new_bus->id in drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
stmmac_mdio_register) and this needs to be unique.
This allows to avoid needing to define ethernet aliases for devices with
multiple stmmac controllers (such as the Rockchip RK3588) for multiple
stmmac devices to probe properly.
Obviously, the bus_id isn't guaranteed to be stable across reboots if no
alias is set for the device but that is easily fixed by simply adding an
alias if this is desired.
Fixes: 25c83b5c2e ("dt:net:stmmac: Add support to dwmac version 3.610 and 3.710")
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250527-stmmac-mdio-bus_id-v2-1-a5ca78454e3c@cherry.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
echo_skb_max should define the supported upper limit of echo_skb[]
allocated inside the netdevice's priv. The corresponding size value
provided by this driver to alloc_candev() is KVASER_PCIEFD_CAN_TX_MAX_COUNT
which is 17.
But later echo_skb_max is rounded up to the nearest power of two (for the
max case, that would be 32) and the tx/ack indices calculated further
during tx/rx may exceed the upper array boundary. Kasan reported this for
the ack case inside kvaser_pciefd_handle_ack_packet(), though the xmit
function has actually caught the same thing earlier.
BUG: KASAN: slab-out-of-bounds in kvaser_pciefd_handle_ack_packet+0x2d7/0x92a drivers/net/can/kvaser_pciefd.c:1528
Read of size 8 at addr ffff888105e4f078 by task swapper/4/0
CPU: 4 UID: 0 PID: 0 Comm: swapper/4 Not tainted 6.15.0 #12 PREEMPT(voluntary)
Call Trace:
<IRQ>
dump_stack_lvl lib/dump_stack.c:122
print_report mm/kasan/report.c:521
kasan_report mm/kasan/report.c:634
kvaser_pciefd_handle_ack_packet drivers/net/can/kvaser_pciefd.c:1528
kvaser_pciefd_read_packet drivers/net/can/kvaser_pciefd.c:1605
kvaser_pciefd_read_buffer drivers/net/can/kvaser_pciefd.c:1656
kvaser_pciefd_receive_irq drivers/net/can/kvaser_pciefd.c:1684
kvaser_pciefd_irq_handler drivers/net/can/kvaser_pciefd.c:1733
__handle_irq_event_percpu kernel/irq/handle.c:158
handle_irq_event kernel/irq/handle.c:210
handle_edge_irq kernel/irq/chip.c:833
__common_interrupt arch/x86/kernel/irq.c:296
common_interrupt arch/x86/kernel/irq.c:286
</IRQ>
Tx max count definitely matters for kvaser_pciefd_tx_avail(), but for seq
numbers' generation that's not the case - we're free to calculate them as
would be more convenient, not taking tx max count into account. The only
downside is that the size of echo_skb[] should correspond to the max seq
number (not tx max count), so in some situations a bit more memory would
be consumed than could be.
Thus make the size of the underlying echo_skb[] sufficient for the rounded
max tx value.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Fixes: 8256e0ca60 ("can: kvaser_pciefd: Fix echo_skb race")
Cc: stable@vger.kernel.org
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Link: https://patch.msgid.link/20250528192713.63894-1-pchelkin@ispras.ru
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
syzbot reported a uaf in page_pool_recycle_in_ring:
BUG: KASAN: slab-use-after-free in lock_release+0x151/0xa30 kernel/locking/lockdep.c:5862
Read of size 8 at addr ffff8880286045a0 by task syz.0.284/6943
CPU: 0 UID: 0 PID: 6943 Comm: syz.0.284 Not tainted 6.13.0-rc3-syzkaller-gdfa94ce54f41 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/13/2024
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:94 [inline]
dump_stack_lvl+0x241/0x360 lib/dump_stack.c:120
print_address_description mm/kasan/report.c:378 [inline]
print_report+0x169/0x550 mm/kasan/report.c:489
kasan_report+0x143/0x180 mm/kasan/report.c:602
lock_release+0x151/0xa30 kernel/locking/lockdep.c:5862
__raw_spin_unlock_bh include/linux/spinlock_api_smp.h:165 [inline]
_raw_spin_unlock_bh+0x1b/0x40 kernel/locking/spinlock.c:210
spin_unlock_bh include/linux/spinlock.h:396 [inline]
ptr_ring_produce_bh include/linux/ptr_ring.h:164 [inline]
page_pool_recycle_in_ring net/core/page_pool.c:707 [inline]
page_pool_put_unrefed_netmem+0x748/0xb00 net/core/page_pool.c:826
page_pool_put_netmem include/net/page_pool/helpers.h:323 [inline]
page_pool_put_full_netmem include/net/page_pool/helpers.h:353 [inline]
napi_pp_put_page+0x149/0x2b0 net/core/skbuff.c:1036
skb_pp_recycle net/core/skbuff.c:1047 [inline]
skb_free_head net/core/skbuff.c:1094 [inline]
skb_release_data+0x6c4/0x8a0 net/core/skbuff.c:1125
skb_release_all net/core/skbuff.c:1190 [inline]
__kfree_skb net/core/skbuff.c:1204 [inline]
sk_skb_reason_drop+0x1c9/0x380 net/core/skbuff.c:1242
kfree_skb_reason include/linux/skbuff.h:1263 [inline]
__skb_queue_purge_reason include/linux/skbuff.h:3343 [inline]
root cause is:
page_pool_recycle_in_ring
ptr_ring_produce
spin_lock(&r->producer_lock);
WRITE_ONCE(r->queue[r->producer++], ptr)
//recycle last page to pool
page_pool_release
page_pool_scrub
page_pool_empty_ring
ptr_ring_consume
page_pool_return_page //release all page
__page_pool_destroy
free_percpu(pool->recycle_stats);
free(pool) //free
spin_unlock(&r->producer_lock); //pool->ring uaf read
recycle_stat_inc(pool, ring);
page_pool can be free while page pool recycle the last page in ring.
Add producer-lock barrier to page_pool_release to prevent the page
pool from being free before all pages have been recycled.
recycle_stat_inc() is empty when CONFIG_PAGE_POOL_STATS is not
enabled, which will trigger Wempty-body build warning. Add definition
for pool stat macro to fix warning.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/netdev/20250513083123.3514193-1-dongchenchen2@huawei.com
Fixes: ff7d6b27f8 ("page_pool: refurbish version of page_pool code")
Reported-by: syzbot+204a4382fcb3311f3858@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=204a4382fcb3311f3858
Signed-off-by: Dong Chenchen <dongchenchen2@huawei.com>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Reviewed-by: Mina Almasry <almasrymina@google.com>
Link: https://patch.msgid.link/20250527114152.3119109-1-dongchenchen2@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In mii_nway_restart() the code attempts to call
mii->mdio_read which is ch9200_mdio_read(). ch9200_mdio_read()
utilises a local buffer called "buff", which is initialised
with control_read(). However "buff" is conditionally
initialised inside control_read():
if (err == size) {
memcpy(data, buf, size);
}
If the condition of "err == size" is not met, then
"buff" remains uninitialised. Once this happens the
uninitialised "buff" is accessed and returned during
ch9200_mdio_read():
return (buff[0] | buff[1] << 8);
The problem stems from the fact that ch9200_mdio_read()
ignores the return value of control_read(), leading to
uinit-access of "buff".
To fix this we should check the return value of
control_read() and return early on error.
Reported-by: syzbot <syzbot+3361c2d6f78a3e0892f9@syzkaller.appspotmail.com>
Closes: https://syzkaller.appspot.com/bug?extid=3361c2d6f78a3e0892f9
Tested-by: syzbot <syzbot+3361c2d6f78a3e0892f9@syzkaller.appspotmail.com>
Fixes: 4a476bd6d1 ("usbnet: New driver for QinHeng CH9200 devices")
Cc: stable@vger.kernel.org
Signed-off-by: Qasim Ijaz <qasdev00@gmail.com>
Link: https://patch.msgid.link/20250526183607.66527-1-qasdev00@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When a process under memory pressure is not part of any cgroup and
the charged flag is false, trace_sock_exceed_buf_limit was not called
as expected.
This regression was introduced by commit 2def8ff3fd ("sock:
Code cleanup on __sk_mem_raise_allocated()"). The fix changes the
default value of charged to true while preserving existing logic.
Fixes: 2def8ff3fd ("sock: Code cleanup on __sk_mem_raise_allocated()")
Signed-off-by: Abel Wu <wuyun.abel@bytedance.com>
Signed-off-by: Tengteng Yang <yangtengteng@bytedance.com>
Link: https://patch.msgid.link/20250527030419.67693-1-yangtengteng@bytedance.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=j3t8
-----END PGP SIGNATURE-----
Merge tag 'bpf-next-6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next
Pull bpf updates from Alexei Starovoitov:
- Fix and improve BTF deduplication of identical BTF types (Alan
Maguire and Andrii Nakryiko)
- Support up to 12 arguments in BPF trampoline on arm64 (Xu Kuohai and
Alexis Lothoré)
- Support load-acquire and store-release instructions in BPF JIT on
riscv64 (Andrea Parri)
- Fix uninitialized values in BPF_{CORE,PROBE}_READ macros (Anton
Protopopov)
- Streamline allowed helpers across program types (Feng Yang)
- Support atomic update for hashtab of BPF maps (Hou Tao)
- Implement json output for BPF helpers (Ihor Solodrai)
- Several s390 JIT fixes (Ilya Leoshkevich)
- Various sockmap fixes (Jiayuan Chen)
- Support mmap of vmlinux BTF data (Lorenz Bauer)
- Support BPF rbtree traversal and list peeking (Martin KaFai Lau)
- Tests for sockmap/sockhash redirection (Michal Luczaj)
- Introduce kfuncs for memory reads into dynptrs (Mykyta Yatsenko)
- Add support for dma-buf iterators in BPF (T.J. Mercier)
- The verifier support for __bpf_trap() (Yonghong Song)
* tag 'bpf-next-6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (135 commits)
bpf, arm64: Remove unused-but-set function and variable.
selftests/bpf: Add tests with stack ptr register in conditional jmp
bpf: Do not include stack ptr register in precision backtracking bookkeeping
selftests/bpf: enable many-args tests for arm64
bpf, arm64: Support up to 12 function arguments
bpf: Check rcu_read_lock_trace_held() in bpf_map_lookup_percpu_elem()
bpf: Avoid __bpf_prog_ret0_warn when jit fails
bpftool: Add support for custom BTF path in prog load/loadall
selftests/bpf: Add unit tests with __bpf_trap() kfunc
bpf: Warn with __bpf_trap() kfunc maybe due to uninitialized variable
bpf: Remove special_kfunc_set from verifier
selftests/bpf: Add test for open coded dmabuf_iter
selftests/bpf: Add test for dmabuf_iter
bpf: Add open coded dmabuf iterator
bpf: Add dmabuf iterator
dma-buf: Rename debugfs symbols
bpf: Fix error return value in bpf_copy_from_user_dynptr
libbpf: Use mmap to parse vmlinux BTF from sysfs
selftests: bpf: Add a test for mmapable vmlinux BTF
btf: Allow mmap of vmlinux btf
...
