Use unsigned int for dev_nack_retry_count across the core and
controller drivers to match the type of master->dev_nack_retry_count.
Update the sysfs store path to use kstrtouint() and adjust the
->set_dev_nack_retry() callback prototype and callers accordingly.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260616113752.196140-4-adrian.hunter@intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Ensure the device is runtime resumed while updating the retry
configuration to avoid accessing the controller while suspended.
Call i3c_master_rpm_get() before accessing the controller in
dev_nack_retry_count_store() and release it with
i3c_master_rpm_put() afterwards.
Fixes: 990c149c61 ("i3c: master: Introduce optional Runtime PM support")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260616113752.196140-3-adrian.hunter@intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Protect master->dev_nack_retry_count against concurrent sysfs updates
by updating it while holding the bus maintenance lock.
Consequently, combine adjacent return statements into one.
For consistency, read dev_nack_retry_count while holding the bus normaluse
lock.
Fixes: b58f47eb39 ("i3c: add sysfs entry and attribute for Device NACK Retry count")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260616113752.196140-2-adrian.hunter@intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Change the below internal static functions to APIs to allow new I3C hub
driver to use them
1) i3c_dev_enable_ibi_locked()
2) i3c_dev_disable_ibi_locked()
3) i3c_dev_request_ibi_locked()
4) i3c_dev_free_ibi_locked()
5) i3c_master_reattach_i3c_dev_locked()
Signed-off-by: Aman Kumar Pandey <aman.kumarpandey@nxp.com>
Signed-off-by: Lakshay Piplani <lakshay.piplani@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260612111816.3688240-3-lakshay.piplani@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Rename i3c_master_reattach_i3c_dev() to *_locked() to make the locking
requirement explicit and consistent with other I3C core helpers that
require the bus lock to be held by the caller.
Signed-off-by: Lakshay Piplani <lakshay.piplani@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260612111816.3688240-2-lakshay.piplani@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add support for microchip sama7d65 SoC I3C HCI master only IP
with additional clock support to enable bulk clock acquisition
and apply the required quirks.
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Manikandan Muralidharan <manikandan.m@microchip.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260525092405.1514213-4-manikandan.m@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add the microchip,sama7d65-i3c-hci compatible string to the MIPI I3C
HCI binding. The Microchip SAMA7D65 I3C controller is based on the
MIPI HCI specification but requires two clocks, so add a conditional
constraint when this compatible is present.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Manikandan Muralidharan <manikandan.m@microchip.com>
Link: https://patch.msgid.link/20260525092405.1514213-2-manikandan.m@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The .driver_data member of the various struct pci_device_id arrays were
initialized by list expressions. This isn't easily readable if you're
not into PCI. Using named initializers is more explicit and thus easier
to parse.
This change doesn't introduce changes to the compiled pci_device_id
arrays. Tested on x86 and arm64.
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260504143324.2122737-2-u.kleine-koenig@baylibre.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
After Dynamic Address Assignment (DAA), there may be cases where
devices have been assigned dynamic addresses on the bus, but are not
successfully registered in the device model. This can happen, for
example, if errors occur during device addition, leaving the bus state
and software state inconsistent.
Introduce a reconciliation step to resolve such inconsistencies.
Scan all address slots marked as I3C devices by the bus, and compare
them against the set of devices currently registered. For any dynamic
address that is marked occupied but has no corresponding i3c_dev_desc,
probe for device presence using a GETSTATUS CCC.
Retry the probe (with exponential backoff delay) to handle transient NACK
conditions. If a device responds, register it via
i3c_master_add_i3c_dev_locked(). Otherwise, free the address
slot so it may be reused in future DAA operations.
Note, i3c_master_add_i3c_dev_locked() may fail (again), in which case the
dynamic address remains marked as occupied. A future DAA will try again.
This also handles a corner case where a device is assigned a dynamic
address but not successfully added, and subsequently loses that address
(e.g. due to power management). If DAA is run again, the device may
receive a new dynamic address while the old one remains marked as
occupied. Repeated occurrences of this scenario could eventually
exhaust the dynamic address space. The reconciliation step ensures that
stale addresses are detected and freed, preventing address leakage.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260612080107.11606-8-adrian.hunter@intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Relocate i3c_master_do_daa_ext() and i3c_master_do_daa() so they appear
after i3c_master_add_i3c_dev_locked().
This ordering is required for upcoming changes where the DAA flow will
(indirectly) rely on i3c_master_add_i3c_dev_locked() functionality.
Reordering avoids forward dependency issues and keeps related code paths
logically arranged.
No functional change.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260612080107.11606-7-adrian.hunter@intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The return value of i3c_master_add_i3c_dev_locked() is not used by any
caller, and callers are not in a position to recover from failures in
this path.
Change the function to return void. Amend the kernel-doc accordingly,
fix some grammar and remove a stale paragraph.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260612080107.11606-6-adrian.hunter@intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
i3c_master_add_i3c_dev_locked() no longer leaves the address marked as
free on failure, so aborting the DAA sequence on its error is unnecessary.
Failure to register a discovered device does not invalidate the entire
Dynamic Address Assignment (DAA) procedure. Align with the behavior of
other I3C master drivers by ignoring errors from
i3c_master_add_i3c_dev_locked() and continuing enumeration.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260612080107.11606-5-adrian.hunter@intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
i3c_master_add_i3c_dev_locked() is called after a device has already
been assigned a dynamic address. If the function fails, the address
remains marked as free and may be reallocated to another device,
leading to address conflicts on the bus.
Ensure the address is not marked as free on failure, by updating the
address slot state to prevent the address from being re-used.
Emit an error message to inform of the failure.
Opportunistically remove the !master check because it is impossible.
Note, directly resetting the device's dynamic address is no longer
an option, since Direct RSTDAA was deprecated from I3C starting from
version 1.1 and v1.1 (or later) target devices are meant to NACK it.
Fixes: 3a379bbcea ("i3c: Add core I3C infrastructure")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260612080107.11606-4-adrian.hunter@intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Disabling IBIs currently returns the result of the DISEC CCC, causing
i3c_hci_disable_ibi() to fail if the transfer errors out.
However, the controller has already been programmed to reject IBIs by
setting DAT_0_SIR_REJECT, so the target’s IBIs are effectively disabled
from the host side regardless of the outcome of the DISEC command. At
this point, teardown of the IBI infrastructure can safely proceed even
if DISEC fails.
Note, from then on, the MIPI I3C HCI not only NACKs the target's IBI but
automatically sends another DISEC command.
Make i3c_hci_disable_ibi() resilient by ignoring the return value of
i3c_master_disec_locked() and always returning success.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260612080107.11606-3-adrian.hunter@intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
i3c_hci_addr_to_dev() walks bus->devs.i3c, which is protected by
bus.lock (rwsem). However, it is invoked from the MIPI I3C HCI IRQ
handler, which cannot take bus.lock. This allows concurrent device
addition/removal in the I3C core to modify the list while it is being
traversed, potentially leading to use-after-free or crashes.
Remove the dependency on the bus device list and introduce a dedicated
lookup table. Add an ibi_devs[] array indexed by DAT entry, maintained
under hci->lock. Update the array when IBIs are enabled or disabled,
so that it always reflects the set of devices allowed to generate IBIs.
Also update when IBIs are freed, to cover the corner case when an IBI is
freed without first being disabled (e.g. oldedev in
i3c_master_add_i3c_dev_locked()).
Move i3c_hci_addr_to_dev() into core.c, reimplement it using the new
array, and add a lockdep assertion to enforce that hci->lock is held
by callers.
Demote a message in PIO and DMA IBI handling, from an error to a debug
message, because there is a race window when the condition can arise
normally.
Fixes: 9ad9a52cce ("i3c/master: introduce the mipi-i3c-hci driver")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260612080107.11606-2-adrian.hunter@intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Wire the MIPI I3C HCI driver into the I3C core Hot-Join framework to
allow targets to dynamically join the bus after initial DAA.
HCI hardware ACKs or NACKs Hot-Join requests based on
HC_CONTROL.HOT_JOIN_CTRL. This was previously left in the
NACK-and-DISEC state, effectively preventing Hot-Join. Implement
the ->enable_hotjoin() and ->disable_hotjoin() master operations
so the core and user space can control this policy at runtime.
Also issue broadcast ENEC HJ when enabling Hot-Join. This is required
because the controller may have previously DISEC'ed the Hot-Join
event, causing targets that were NACKed once to never retry.
Acknowledged Hot-Join requests are delivered as IBIs on the reserved
address 0x02. Update both the DMA and PIO IBI paths to recognise this
address and forward the event to i3c_master_queue_hotjoin().
To make Hot-Join usable by default, enable it once after the initial
DAA. This is gated by rpm_ibi_allowed, since otherwise keeping Hot-Join
enabled prevents runtime suspend. A new hj_init_done flag ensures this
one-time enablement is not repeated on subsequent DAAs.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260608054312.10604-9-adrian.hunter@intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The existing i3c_master_enec_locked() wrapper always treats a NACKed
ENEC CCC as a failure (M2 error). However, broadcasting ENEC to enable
Hot-Join is legitimately useful even when no I3C devices are currently
present on the bus, in which case the broadcast will be NACKed and
should not be reported as an error.
The underlying helper i3c_master_enec_disec_locked() already accepts a
suppress_m2 flag that lets callers ignore such NACKs. Expose it so that
a subsequent patch enabling Hot-Join events can issue ENEC with M2
suppression.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260608054312.10604-8-adrian.hunter@intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Master drivers may invoke i3c_master_do_daa_ext() during resume to
re-run Dynamic Address Assignment. As well as assigning addresses to
any newly arrived devices, this restores the dynamic address of devices
that lost it across system suspend, so it has to run as part of the
controller's resume path.
A side effect of i3c_master_do_daa_ext() today is that it also
registers any newly discovered I3C devices with the driver model
inline, via i3c_master_register_new_i3c_devs(). Doing that from the
resume path is problematic: a hot-join-capable device may join the bus
during this same DAA, and registering it immediately would push driver
model work (probing, sysfs, etc.) into the controller's resume context,
where the rest of the system is not yet fully resumed and the
controller driver is still partway through its own resume sequence.
Decouple discovery from registration: add a reg_work work item to
struct i3c_master_controller and have i3c_master_do_daa_ext() queue it
on master->wq (the freezable workqueue) instead of calling
i3c_master_register_new_i3c_devs() directly. The worker performs the
registration only when the controller is not shutting_down, and is
cancelled alongside hj_work in i3c_master_shutdown(). Because wq is
freezable, any newly observed devices end up being registered after
the system has finished resuming.
i3c_master_register() also routes its initial post-bus-init registration
through reg_work, using flush_work() to keep probe-time behavior
synchronous. This keeps a single registration code path and ensures the
worker is the only writer of desc->dev.
Fixes: 3a379bbcea ("i3c: Add core I3C infrastructure")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260608054312.10604-7-adrian.hunter@intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The I3C core now installs an i3c_bus_type shutdown callback that
flushes master->hj_work (via i3c_master_shutdown()) before any driver's
platform shutdown hook runs. The explicit cancel_work_sync() in
dw_i3c_shutdown() is therefore redundant: by the time it executes, the
Hot-Join worker has already been cancelled, and the shutting_down gate
makes a new worker a no-op.
Remove the now-unneeded call. No functional change.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260608054312.10604-6-adrian.hunter@intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
System shutdown invokes each device's bus shutdown callback to quiesce
hardware, but the I3C bus type does not currently implement one. As a
result, on shutdown the controller's Hot-Join work and any in-flight
i3c_master_do_daa() can keep running (or be newly triggered) while the
rest of the system is being torn down.
A similar window exists at i3c_master_unregister() time: cancel_work_sync()
on hj_work prevents queued work from completing, but does not stop a
fresh Hot-Join IBI from re-queueing the worker, nor a concurrent sysfs
writer from toggling Hot-Join via i3c_set_hotjoin().
Introduce a single "shutting down" gate in the I3C core, set under the
bus maintenance lock so it is observed by any in-progress DAA path
before pending work is cancelled. Install an i3c_bus_type shutdown
callback that engages this gate for master devices during system
shutdown, and use the same gate in i3c_master_unregister() so both
paths get identical guarantees.
Once the gate is engaged, the Hot-Join worker, i3c_master_do_daa_ext()
and i3c_set_hotjoin() all bail out cleanly, so Hot-Join IBIs that race
with shutdown become no-ops, direct DAA callers see -ENODEV, and sysfs
writers can no longer re-enable Hot-Join through ops->enable_hotjoin()
while the controller is going away.
No functional change for the steady-state runtime path; the new checks
only take effect once the controller has been marked as shutting down.
Note, this patch depends on patch "i3c: master: Consolidate Hot-Join DAA
work in the core".
Fixes: 3a379bbcea ("i3c: Add core I3C infrastructure")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260608054312.10604-5-adrian.hunter@intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Three master drivers (dw-i3c-master, i3c-master-cdns, svc-i3c-master)
each carry an essentially identical Hot-Join handler: a struct
work_struct embedded in their private state, a work function that just
calls i3c_master_do_daa() on the embedded i3c_master_controller, plus
matching INIT_WORK()/cancel_work_sync() boilerplate in probe/remove (and
shutdown for dw-i3c). The IBI/ISR paths then queue that work onto
master->wq, which already lives in the core.
Move this pattern into the I3C core:
- Add struct work_struct hj_work to struct i3c_master_controller and
initialise it in i3c_master_register() with a core-provided handler
i3c_master_hj_work_fn() that performs i3c_master_do_daa().
- Cancel the work in i3c_master_unregister() so all controllers get
correct teardown ordering against the workqueue for free.
- Export i3c_master_queue_hotjoin() as the single entry point drivers
call from their Hot-Join IBI handler.
Convert the three existing users to the new API: drop their private
hj_work fields, work functions, INIT_WORK() and cancel_work_sync()
calls, and replace the queue_work(master->wq, &drv->hj_work) call sites
with i3c_master_queue_hotjoin(&drv->base). The dw-i3c shutdown path
still needs to flush pending Hot-Join work before tearing down the
hardware, so it is updated to cancel master->base.hj_work directly.
No functional change intended: the work is still queued on the same
master->wq, runs the same i3c_master_do_daa(), and is cancelled at
controller teardown. Future Hot-Join improvements now only need to
be made in one place.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260608054312.10604-4-adrian.hunter@intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
i3c_set_hotjoin() dispatches the controller's enable_hotjoin() or
disable_hotjoin() op and updates master->hotjoin under
i3c_bus_normaluse_lock(). That lock is a read-side acquisition of
bus->lock (down_read()), so it does not exclude concurrent callers.
The hotjoin sysfs attribute can be opened multiple times, and writes
through different opens are not serialized. Two concurrent writers
to "hotjoin" can therefore race in i3c_set_hotjoin(), with the
controller op and the master->hotjoin store from one call interleaving
with the other. The hardware enable/disable state and the value reported
by hotjoin_show() can end up out of sync.
Take i3c_bus_maintenance_lock() instead. Toggling Hot Join enable
changes bus state and is conceptually a maintenance operation, so the
write-side acquisition of bus->lock is the appropriate lock and
serializes concurrent callers against each other and against other
maintenance operations.
Fixes: 317bacf960 ("i3c: master: add enable(disable) hot join in sys entry")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260608054312.10604-3-adrian.hunter@intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The I3C master workqueue (master->wq) is used to defer work that needs
thread context and the bus maintenance lock, most notably Hot Join
processing (which calls i3c_master_do_daa() to assign dynamic addresses
to newly joined devices).
Currently the workqueue keeps running across system suspend, which can
race with the suspend path:
- do_daa() may execute after the controller has been suspended,
issuing bus transactions on a powered-down or otherwise unusable
controller.
- New I3C devices can be enumerated and added to the bus mid-suspend,
registering driver model objects at a point where the I3C subsystem
and its consumers are not prepared to handle them.
Mark the workqueue WQ_FREEZABLE so its workers are frozen for the
duration of system suspend/hibernate and resumed afterwards. This
naturally defers any pending or newly queued Hot Join work until the
system (and the controller) is fully resumed, closing both races
without adding explicit suspend/resume synchronization in the master
drivers.
Update the kerneldoc for struct i3c_master_controller::wq to reflect
that the workqueue is freezable.
Fixes: 3a379bbcea ("i3c: Add core I3C infrastructure")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260608054312.10604-2-adrian.hunter@intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The DMA transfer ring is currently limited to 16 entries, despite the
MIPI I3C HCI supporting up to 32 devices. When the ring lacks space for a
new transfer list, the driver returns -EBUSY, which can be unexpected
for clients.
Increase the DMA transfer ring size to the maximum supported value of
255 entries. This effectively eliminates ring-space exhaustion in
practice and avoids the complexity of adding secondary queuing
mechanisms.
Even at the maximum size, the memory overhead remains small
(approximately 24 bytes per entry by default).
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260603090754.16252-18-adrian.hunter@intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
dma_alloc_coherent() allocates memory in whole pages, which can waste
space when command and response queues are allocated separately.
Allocate the DMA command and response queues from a single coherent
allocation instead, while preserving the required 4-byte alignment.
This reduces memory overhead without changing behavior.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260603090754.16252-17-adrian.hunter@intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Transfer timeouts are currently measured from the point where a transfer
list is queued to the controller. This can cause transfers to time out
before they have actually started, if earlier queued transfers consume
the timeout interval.
Fix this by recording when a transfer reaches the head of the queue and
adjusting the timeout calculation to start from that point. The existing
low-overhead completion-based timeout mechanism is preserved, but care is
taken to ensure the transfer start time is consistently recorded for both
PIO and DMA paths.
This prevents premature timeouts while retaining efficient timeout
handling.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260603090754.16252-16-adrian.hunter@intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
When a transfer list is only partially completed due to an error,
hci_dma_dequeue_xfer() overwrites the remaining DMA ring entries with
NoOp commands and restarts the ring to flush them out.
While NoOp commands are expected to complete successfully, they may still
fail to complete if the DMA ring is stuck. Explicitly wait for the NoOp
commands to finish, and trigger controller recovery if they do not
complete or report an error.
This ensures that partially completed transfer lists are reliably
resolved and that a stuck ring is recovered promptly.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260603090754.16252-15-adrian.hunter@intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Handle internal I3C HCI errors when operating in DMA mode by adding a
simple recovery mechanism.
On detection of an internal controller error, mark recovery as needed and
attempt to restore operation by performing a software reset followed by
state restore. To keep recovery straightforward on this unlikely error
path, all currently queued transfers are terminated and completed with an
error.
This allows the controller to resume operation after internal failures
rather than remaining permanently stuck.
Note, internal errors indicated by INTR_HC_INTERNAL_ERR, cause the
controller to stop.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260603090754.16252-14-adrian.hunter@intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Factor the reset-and-restore sequence out of i3c_hci_rpm_resume() into
a separate helper.
This allows the same logic to be reused for recovery paths in subsequent
changes without duplicating suspend/resume handling.
No functional change.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260603090754.16252-13-adrian.hunter@intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
DMA rings can be aborted either per-ring via RING_CONTROL or globally
via HC_CONTROL_ABORT. The driver currently relies on the per-ring
mechanism.
Some Intel I3C HCI controllers require HC_CONTROL_ABORT to be asserted
before a DMA ring abort is effective. This behavior is non-standard.
Introduce a controller quirk to select the required abort method and
enable it for Intel LPSS I3C controllers.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260603090754.16252-12-adrian.hunter@intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Factor out hci_dma_abort() from hci_dma_dequeue_xfer() in preparation
for further changes.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260603090754.16252-11-adrian.hunter@intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Some Intel I3C HCI controllers cannot reliably restart a DMA ring after an
ABORT. Additional queue resets are required to recover, and must be
performed using PIO reset bits even while operating in DMA mode.
This behavior is non-standard. Introduce a controller quirk to opt into
the required PIO queue resets after a DMA ring abort, and enable it for
Intel LPSS I3C controllers.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260603090754.16252-10-adrian.hunter@intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Software ABORT of the DMA ring is used to recover from transfer list
timeouts, but it is inherently racy. The intended transfer list may
complete just before the ABORT takes effect, causing the subsequent
transfer list to be aborted instead.
In this case, an incomplete transfer list may remain in the ring and has
not yet been processed by hci_dma_dequeue_xfer(). Restarting the DMA
ring at that point can lead to unpredictable results.
Detect when the next queued transfer is not the first entry of a transfer
list and does not belong to the list currently being dequeued. In that
case, skip restarting the DMA ring and defer recovery until a subsequent
call to hci_dma_dequeue_xfer(), which will safely restart the ring once
the incomplete list is handled.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260603090754.16252-9-adrian.hunter@intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
In DMA mode, transfer lists are currently completed only when the final
transfer in the list completes. If an earlier transfer fails, the list is
left incomplete and callers wait until timeout.
There is no need to wait for a timeout, as the completion path in
i3c_hci_process_xfer() already checks for error status. Complete the
transfer list as soon as any transfer in the list reports an error.
This avoids unnecessary delays and spurious timeouts on error.
Complete a transfer list completion immediately there is an error.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260603090754.16252-8-adrian.hunter@intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
hci_dma_dequeue_xfer() relies on state normally updated by the DMA
interrupt handler. Ensure that state is current by explicitly invoking
hci_dma_xfer_done() from the dequeue path.
This handles cases where the interrupt handler has not (yet) run.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260603090754.16252-7-adrian.hunter@intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Move hci_dma_xfer_done() earlier in the file to avoid a forward
declaration needed by a subsequent change.
No functional change.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260603090754.16252-6-adrian.hunter@intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Although hci_dma_dequeue_xfer() is serialized against itself via
control_mutex, this does not guarantee that a DMA ring restart
triggered by a previous invocation has fully completed.
When the function is called again in rapid succession, the DMA ring may
still be transitioning back to the running state, which may confound or
disrupt further state changes.
Address this by waiting for the DMA ring restart to complete before
continuing.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260603090754.16252-5-adrian.hunter@intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Block the DMA enqueue path while a Ring abort is in progress or after an
error condition has been detected.
Previously, new transfers could be enqueued while the DMA Ring was being
aborted or while error handling was underway. This allowed enqueue and
error-recovery paths to run concurrently, potentially interfering with
each other and corrupting Ring state.
Introduce explicit enqueue blocking and a wait queue to serialize access:
enqueue operations now wait until abort or error handling has completed
before proceeding. Enqueue is unblocked once the Ring is safely restarted.
Note, there is only 1 ring bundle configured, and a transfer error causes
the controller to halt ring (bundle) operation, so there is only ever 1
outstanding error at a time. Furthermore, a later patch ensures that only
the currently active transfer list can time out. Consequently, the DMA
queue will not be unblocked while there are outstanding transfer errors or
timeouts.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260603090754.16252-4-adrian.hunter@intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The MIPI I3C HCI specification does not require the DMA ring RUN bit
(RUN_STOP) to be cleared when issuing an ABORT. That allows the DMA ring
to continue to receive IBIs, although an IBI is anyway not lost because it
can be received once the ring restarts if the I3C device has not given up.
Note, currently ABORT is only used on a timeout error path so the change
has very little effect in practice. In the more common case of a transfer
error, the ring (bundle) operation is halted by the controller anyway.
Adjust the RING_CONTROL handling to set ABORT without clearing RUN_STOP,
bringing the driver into alignment with the specification.
Fixes: b795e68bf3 ("i3c: mipi-i3c-hci: Correct RING_CTRL_ABORT handling in DMA dequeue")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260603090754.16252-3-adrian.hunter@intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Software reset was introduced as a fallback if bus disable failed. The
change was made in 2 places: the cleanup path and the suspend path.
For the cleanup path (i3c_hci_bus_cleanup()), after software reset the
function continues to do cleanup for the current I/O mode. For the
suspend path (i3c_hci_rpm_suspend()), after software reset the function
returns early. However software reset does not reset any Ring Headers in
the Host Controller, so returning early is not the right thing to do.
Instead, continue to call suspend for the current I/O mode, which for DMA
mode will reset any Ring Headers.
Note, although Ring Headers should not be active at this stage, performing
this reset follows the procedure defined by the specification and keeps
the suspend path consistent with the cleanup path.
Note also, i3c_hci_sync_irq_inactive() is still called via the PIO and DMA
hci->io->suspend() callbacks.
Always return 0 because the device is quiesced as much as possible and
returning a negative error code would unnecessarily prevent system suspend.
Fixes: 9a258d1336 ("i3c: mipi-i3c-hci: Fallback to software reset when bus disable fails")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260603090754.16252-2-adrian.hunter@intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
On DesignWare I3C controllers where IC_HAS_IBI_DATA=0 (such as versalnet),
the IBI_STS_CNT field (bits [28:24] of QUEUE_STATUS_LEVEL) is hardwired
to 0. The IBI status entry count is instead reported via IBI_BUF_BLR
(bits [23:16] of the same register).
irq_handle_ibis() was unconditionally reading IBI_STS_CNT, causing it to
always see 0 pending IBIs on versalnet and return early without draining
the IBI buffer. Since INTR_IBI_THLD_STAT is level-triggered against the
buffer fill level, this left the interrupt permanently asserted.
Detect IBI data capability at probe time by writing the IBI data threshold
field in QUEUE_THLD_CTRL and reading it back. Use the result to select the
correct register field in irq_handle_ibis().
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@amd.com>
Link: https://patch.msgid.link/20260401084430.436059-1-shubhrajyoti.datta@amd.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Replace sprintf() function calls with sysfs_emit() and
sysfs_emit_at() function calls where appropriate. This will help
harden the driver and help modernize it. While at it, add missing
newlines at the end of some sysfs_emit() (formerly sprintf()) calls.
Signed-off-by: Maxwell Doose <m32285159@gmail.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260421214837.20939-1-m32285159@gmail.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
On NPCM845, when a target on the I3C bus gets stuck holding SDA low,
the controller reports a false Master Request (MR) in-band interrupt
event. The driver handles this by emitting a STOP condition to restore
the bus.
However, the hardware quirk SVC_I3C_QUIRK_FALSE_SLVSTART indicates that
emitting a STOP condition may spuriously set the SLVSTART interrupt
status bit. In the Master Request case, this creates a feedback loop:
the STOP triggers a new SLVSTART event, the IRQ handler fires again,
the controller still reports an MR type, another STOP is emitted, and
the cycle repeats indefinitely, resulting in an IRQ storm that can lock
up the CPU.
Clear the SLVSTART status bit explicitly after emitting the STOP in the
Master Request IBI handler when the SVC_I3C_QUIRK_FALSE_SLVSTART quirk
is set. This breaks the feedback loop without affecting normal SLVSTART
processing, which is already guarded in the top-level IRQ handler by
checking that MSTATUS is in SLVREQ state.
Signed-off-by: Stanley Chu <yschu@nuvoton.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260413005040.1211107-3-yschu@nuvoton.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The NPCM845 I3C controller may raise a false SLVSTART interrupt. The
handler first latches MSTATUS and then clears SLVSTART. If a real IBI
request arrives after the handler latches MSTATUS but before it clears
the SLVSTART interrupt status, HW sets the SLVREQ state. However, the
handler still relies on the stale MSTATUS snapshot, returns early, and
misses the real IBI. No further interrupt is generated for this pending
IBI.
Re-read MSTATUS to obtain the latest state and avoid missing a real IBI
due to this race condition.
Fixes: 4dd12e944f ("i3c: master: svc: Fix npcm845 invalid slvstart event")
Signed-off-by: Stanley Chu <yschu@nuvoton.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260413005040.1211107-2-yschu@nuvoton.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Raspberry Pi 3B by marking the VEC clk critical so it doesn't get
turned off and hang the bus.
-----BEGIN PGP SIGNATURE-----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=JtUn
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fix from Stephen Boyd:
"One more fix for the merge window to avoid a boot hang on
Raspberry Pi 3B by marking the VEC clk critical so that it
doesn't get turned off and hang the bus"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: bcm: rpi: Mark VEC clock as CLK_IGNORE_UNUSED
- Drop class_create() for the "tsm" class
-----BEGIN PGP SIGNATURE-----
iIYEABYKAC4WIQSbo+XnGs+rwLz9XGXfioYZHlFsZwUCae40aBAcZGpid0BrZXJu
ZWwub3JnAAoJEN+KhhkeUWxn/F0BAIpdhnq3TbPMC6Pj0q3DfcXpP+LPD0pqqIom
TwsQVZJCAP4rYVEbIbgeXvkilr7Fpcs2AXbidR/ggBsR3lyVBSNhAA==
=ZK/r
-----END PGP SIGNATURE-----
Merge tag 'tsm-for-7.1' of git://git.kernel.org/pub/scm/linux/kernel/git/devsec/tsm
Pull PCIe TSP update from Dan Williams:
"A small update for the TSM core. It is arguably a fix and coming in
late as I have been offline the past few weeks:
- Drop class_create() for the 'tsm' class"
* tag 'tsm-for-7.1' of git://git.kernel.org/pub/scm/linux/kernel/git/devsec/tsm:
virt: coco: change tsm_class to a const struct
- kbuild: builddeb - avoid recompiles for non-cross-compiles
Avoid triggering complete rebuilds for non-cross-compile Debian
package builds by only triggering the rebuild of host tools for
actual cross-compile builds.
- kbuild: Never respect CONFIG_WERROR / W=e to fixdep
Avoid spurious rebuilds of fixdep w/ and w/o -Werror during a single
kbuild invocation by never respecting CONFIG_WERROR for fixdep.
Cc: Masahiro Yamada <masahiroy@kernel.org>
Cc: Mathias Krause <minipli@grsecurity.net>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Thomas Weißschuh <linux@weissschuh.net>
-----BEGIN PGP SIGNATURE-----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=yCeR
-----END PGP SIGNATURE-----
Merge tag 'kbuild-fixes-7.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kbuild/linux
Pull Kbuild fixes from Nicolas Schier:
- builddeb - avoid recompiles for non-cross-compiles
Avoid triggering complete rebuilds for non-cross-compile Debian
package builds by only triggering the rebuild of host tools for
actual cross-compile builds
- Never respect CONFIG_WERROR / W=e to fixdep
Avoid spurious rebuilds of fixdep w/ and w/o -Werror during a single
kbuild invocation by never respecting CONFIG_WERROR for fixdep
* tag 'kbuild-fixes-7.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kbuild/linux:
kbuild: Never respect CONFIG_WERROR / W=e to fixdep
kbuild: builddeb - avoid recompiles for non-cross-compiles
Subsystem:
- add data_race() in rtc_dev_poll()
Drivers:
- remove i2c_match_id usage
- abx80x: Disable alarm feature if no interrupt attached
- ti-k3: support resuming from IO DDR low power mode
-----BEGIN PGP SIGNATURE-----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=mY/t
-----END PGP SIGNATURE-----
Merge tag 'rtc-7.1' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"Subsystem:
- add data_race() in rtc_dev_poll()
Drivers:
- remove i2c_match_id usage
- abx80x: Disable alarm feature if no interrupt attached
- ti-k3: support resuming from IO DDR low power mode"
* tag 'rtc-7.1' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
rtc: abx80x: Disable alarm feature if no interrupt attached
rtc: ntxec: fix OF node reference imbalance
rtc: pic32: allow driver to be compiled with COMPILE_TEST
rtc: ti-k3: Add support to resume from IO DDR low power mode
rtc: cmos: Use platform_get_irq_optional() in cmos_platform_probe()
dt-bindings: rtc: add olpc,xo1-rtc to trivial-rtc
dt-bindings: rtc: sc2731: Add compatible for SC2730
rtc: add data_race() in rtc_dev_poll()
rtc: armada38x: zalloc + calloc to single allocation
dt-bindings: rtc: isl12026: convert to YAML schema
dt-bindings: rtc: microcrystal,rv3028: Allow to specify vdd-supply
rtc: max77686: convert to i2c_new_ancillary_device
dt-bindings: rtc: mpfs-rtc: permit resets
rtc: rx8025: Remove use of i2c_match_id()
rtc: rv8803: Remove use of i2c_match_id()
rtc: rs5c372: Remove use of i2c_match_id()
rtc: pcf2127: Remove use of i2c_match_id()
rtc: m41t80: Remove use of i2c_match_id()
rtc: abx80x: Remove use of i2c_match_id()
