On RSCI IP, a deadlock occurs during a FIFO overrun error, as it uses a
different register to clear the FIFO overrun error status.
Cc: stable@kernel.org
Fixes: 0666e3fe95 ("serial: sh-sci: Add support for RZ/T2H SCI")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251114101350.106699-3-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the driver for on-chip UART used on Loongson family chips.
The hardware is similar to NS16550A, but there are the following
differences:
- Some chips (such as Loongson-2K2000) have added a fractional division
register to obtain the required baud rate accurately, so the
{get,set}_divisor callback is overridden.
- Due to hardware defects, quirk handling is required for
UART_MCR/UART_MSR.
Co-developed-by: Haowei Zheng <zhenghaowei@loongson.cn>
Signed-off-by: Haowei Zheng <zhenghaowei@loongson.cn>
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Reviewed-by: Huacai Chen <chenhuacai@loongson.cn>
Link: https://patch.msgid.link/2c2a01a276b9250efea0c7aa190efecdfd6fdf5a.1760166651.git.zhoubinbin@loongson.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The KEBA UART is found in the system FPGA of KEBA PLC devices. It is
mostly 8250 compatible with extension for some UART modes.
3 different variants exist. The simpliest variant supports only RS-232
and is used for debug interfaces. The next variant supports only RS-485
and is used mostly for communication with KEBA panel devices. The third
variant is able to support RS-232, RS-485 and RS-422. For this variant
not only the mode of the UART is configured, also the physics and
transceivers are switched according to the mode.
Signed-off-by: Gerhard Engleder <eg@keba.com>
Tested-by: Daniel Gierlinger <gida@keba.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Link: https://patch.msgid.link/20251023151229.11774-3-gerhard@engleder-embedded.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit fe7f0fa43c ("serial: 8250: Support rs485 devicetree properties")
retrieves rs485 properties for 8250 drivers. These properties are read
from the firmware node of the device within uart_get_rs485_mode(). If the
firmware node does not exist, then the rs485 flags are still reset. Thus,
8250 driver cannot set rs485 flags to enable a defined rs485 mode during
driver loading. This is no problem so far, as no 8250 driver sets the
rs485 flags.
The default rs485 mode can also be set by firmware nodes. But for some
devices a firmware node does not exist. E.g., for a PCIe based serial
interface on x86 no device tree is available and the ACPI information of
the BIOS often cannot by modified. In this case it shall be possible,
that a driver works out of the box by setting a reasonable default rs485
mode.
If no firmware node exists, then it should be possible for the driver to
set a reasonable default rs485 mode. Therefore, reset rs485 flags only
if a firmware node exists.
Signed-off-by: Gerhard Engleder <eg@keba.com>
Cc: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Link: https://patch.msgid.link/20251023151229.11774-2-gerhard@engleder-embedded.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Qualcomm automotive SA8255p SoC relies on firmware to configure
platform resources, including clocks, interconnects and TLMM.
The driver requests resources operations over SCMI using power
and performance protocols.
The SCMI power protocol enables or disables resources like clocks,
interconnect paths, and TLMM (GPIOs) using runtime PM framework APIs,
such as resume/suspend, to control power states(on/off).
The SCMI performance protocol manages UART baud rates, with each baud
rate represented by a performance level. The driver uses the
dev_pm_opp_set_level() API to request the desired baud rate by
specifying the performance level.
Signed-off-by: Praveen Talari <praveen.talari@oss.qualcomm.com>
Link: https://patch.msgid.link/20251110101043.2108414-5-praveen.talari@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The GENI serial driver currently handles power resource management
through calls to the statically defined geni_serial_resources_on() and
geni_serial_resources_off() functions. This approach reduces modularity
and limits support for platforms with diverse power management
mechanisms, including resource managed by firmware.
Improve modularity and enable better integration with platform-specific
power management, introduce support for runtime PM. Use
pm_runtime_resume_and_get() and pm_runtime_put_sync() within the
qcom_geni_serial_pm() callback to control resource power state
transitions based on UART power state changes.
Signed-off-by: Praveen Talari <praveen.talari@oss.qualcomm.com>
Link: https://patch.msgid.link/20251110101043.2108414-4-praveen.talari@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In sprd_clk_init(), when devm_clk_get() returns -EPROBE_DEFER
for either uart or source clock, we should propagate the
error instead of just warning and continuing with NULL clocks.
Currently the driver only emits a warning when clock acquisition
fails and proceeds with NULL clock pointers. This can lead to
issues later when the clocks are actually needed. More importantly,
when the clock provider is not ready yet and returns -EPROBE_DEFER,
we should return this error to allow deferred probing.
This change adds explicit checks for -EPROBE_DEFER after both:
1. devm_clk_get(uport->dev, uart)
2. devm_clk_get(uport->dev, source)
When -EPROBE_DEFER is encountered, the function now returns
-EPROBE_DEFER to let the driver framework retry probing
later when the clock dependencies are resolved.
Signed-off-by: Wenhua Lin <Wenhua.Lin@unisoc.com>
Link: https://patch.msgid.link/20251022030840.956589-1-Wenhua.Lin@unisoc.com
Reviewed-by: Cixi Geng <cixi.geng@linux.dev>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It makes it possible to use just "earlycon" param in kernel cmdline
on Exynos850 based boards instead of "earlycon=exynos4210,0x13820000",
as described in [1]:
When used with no options, the early console is determined by
stdout-path property in device tree's chosen node
[1] Documentation/admin-guide/kernel-parameters.txt
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://patch.msgid.link/20251118024822.28148-1-semen.protsenko@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
icom_probe() uses pci_read_config_dword() that returns PCIBIOS_*
codes. The return code is returned from the probe function as is but
probe functions should return normal errnos. A proper implementation
can be found in drivers/leds/leds-ss4200.c
Convert PCIBIOS_* return codes using pcibios_err_to_errno() into
normal errno before returning them.
Signed-off-by: Haotian Zhang <vulab@iscas.ac.cn>
Link: https://patch.msgid.link/20251117040710.1544-1-vulab@iscas.ac.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch resolves the warning "sizeof *port should be sizeof(*port)"
detected by checkpatch.pl.
Signed-off-by: jempty.liang <imntjempty@163.com>
Link: https://patch.msgid.link/20251117034117.55588-1-imntjempty@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Addi-Data GmbH is manufacturing multi-serial ports cards supporting CompactPCI (known as CPCI).
Those cards are identified with different DeviceIds. Those cards integrating standard UARTs
work the same way as PCI/PCIe models already supported in the serial driver.
Signed-off-by: Magne Bruno <magne.bruno@addi-data.com>
Link: https://patch.msgid.link/20251110162456.341029-1-magne.bruno@addi-data.com
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The validator is not happy:
Warning: drivers/tty/serial/mux.c:351 expecting prototype for mux_drv_poll(). Prototype was for mux_poll() instead
Update the kernel-doc accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20251106113815.2302539-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently if a user enqueue a work item using schedule_delayed_work() the
used wq is "system_wq" (per-cpu wq) while queue_delayed_work() use
WORK_CPU_UNBOUND (used when a cpu is not specified). The same applies to
schedule_work() that is using system_wq and queue_work(), that makes use
again of WORK_CPU_UNBOUND.
This lack of consistentcy cannot be addressed without refactoring the API.
This patch continues the effort to refactor worqueue APIs, which has begun
with the change introducing new workqueues and a new alloc_workqueue flag:
commit 128ea9f6cc ("workqueue: Add system_percpu_wq and system_dfl_wq")
commit 930c2ea566 ("workqueue: Add new WQ_PERCPU flag")
system_dfl_wq should be the default workqueue so as not to enforce
locality constraints for random work whenever it's not required.
The old system_unbound_wq will be kept for a few release cycles.
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Marco Crivellari <marco.crivellari@suse.com>
Link: https://patch.msgid.link/20251104105446.110884-1-marco.crivellari@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In 2009, commit c82f63e411 ("PCI: check saved state before restore")
changed the behavior of pci_restore_state() such that it became necessary
to call pci_save_state() afterwards, lest recovery from subsequent PCI
errors fails.
The commit has just been reverted and so all the pci_save_state() after
pci_restore_state() calls that have accumulated in the tree are now
superfluous. Drop them.
Two drivers chose a different approach to achieve the same result:
drivers/scsi/ipr.c and drivers/net/ethernet/intel/e1000e/netdev.c set the
pci_dev's "state_saved" flag to true before calling pci_restore_state().
Drop this as well.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com> # qat
Link: https://patch.msgid.link/c2b28cc4defa1b743cf1dedee23c455be98b397a.1760274044.git.lukas@wunner.de
IRQF_SHARED is the only flag handled in __serial8250_isa_init_ports()
and serial8250_probe_platform(). There is no need to precompute the
flags. Instead, initialize port->irqflags directly in the for loop.
Note the "if (bool)" is cheap and these are not hot paths anyway.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://patch.msgid.link/20251119092457.826789-7-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
8250_core is the only place where skip_txen_test is used. And platform
and core end up in 8250.ko, so there is no change in module name (param
prefix). Therefore, move skip_txen_test there and make it local.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://patch.msgid.link/20251119092457.826789-5-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In 3.7, 8250 was unintentionally renamed to 8250_core. This happened in
the commit 835d844d1a (8250_pnp: do pnp probe before legacy probe).
This made 8250.<xxxx> module options effectively defunct. Instead,
8250_core.<xxxx> worked.
In 3.9, the commit f2b8dfd9e4 (serial: 8250: Keep 8250.<xxxx> module
options functional after driver rename) made the original options work
again by introducing a hack.
Later in 3.9, the commit 9196d8acd7 (TTY: 8250, revert module name
change) changed the module name back to 8250 (from 8250_core). Since
then, the hack was there to support the transient 8250_core.<xxxx>
options. Those were present only in the 3.7..3.9 range.
These transient options were deprecated by 9326b047e4 (TTY: 8250,
deprecated 8250_core.* options) in v3.9 too.
Now, after those 12 years, it is time to get rid of this hack
completely.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://patch.msgid.link/20251119092457.826789-4-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Provided the uart driver is available globally, there is no need to
store a pointer to it in struct cdns_uart. Instead, use the global
cdns_uart_uart_driver in the code directly.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Link: https://patch.msgid.link/20251119092457.826789-3-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use guards in the serial_core code. This improves readability, makes
error handling easier, and marks locked portions of code explicit. All
that while being sure the lock is unlocked.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://patch.msgid.link/20251119100140.830761-11-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Neither uart_do_autoconfig(), nor uart_wait_modem_status() can return
-ENOIOCTLCMD. The ENOIOCTLCMD checks are there to check if 'cmd' matched
against TIOCSERCONFIG, and TIOCMIWAIT respectively. (With 0 or error in
'ret', it does not matter.)
Therefore, the code can simply return from the TIOCSERCONFIG and
TIOCMIWAIT spots immediately.
To be more explicit, use 'if' instead of switch-case for those single
values.
And return without jumping to the 'out' label -- it can be removed too.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://patch.msgid.link/20251119100140.830761-10-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use guards in the vt/keyboard code. This improves readability, makes
error handling easier, and marks locked portions of code explicit. All
that while being sure the lock is unlocked.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://patch.msgid.link/20251119100140.830761-9-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Return immediately when something goes wrong in vt_do_kbkeycode_ioctl().
This makes the code flow more obvious.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://patch.msgid.link/20251119100140.830761-8-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The vt/keyboard code can use __free to ensure the temporary buffers are
freed. Perform the switch.
And even one non-temporary in kbd_connect(). There are fail paths, so
ensure the buffer is freed in them and not when returning 0 -- by
retain_and_null_ptr().
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://patch.msgid.link/20251119100140.830761-7-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use guards in the moxa code. This improves readability, makes error
handling easier, and marks locked portions of code explicit. All that
while being sure the lock is unlocked.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://patch.msgid.link/20251119100140.830761-6-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use guards in the n_hdlc code. This improves readability, makes error
handling easier, and marks locked portions of code explicit. All that
while being sure the lock is unlocked.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://patch.msgid.link/20251119100140.830761-5-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The cases in the switch() of n_hdlc_tty_ioctl() can return immediately
-- no need to store into error and return later.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://patch.msgid.link/20251119100140.830761-4-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use guards in the n_tty code. This improves readability, makes error
handling easier, and marks locked portions of code explicit. All that
while being sure the lock is unlocked.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://patch.msgid.link/20251119100140.830761-3-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use guards in the pty code. This improves readability, makes error
handling easier, and marks locked portions of code explicit. All that
while being sure the lock is unlocked.
pty_set_pktmode() is handled specially -- the conditions are inverted
and return called if conditions unmet. This avoid double nested 'if's.
The variable is renamed to want_pktmode so it is not confused with the
current state of pktmode.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://patch.msgid.link/20251119100140.830761-2-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The row/column bounds (for a screen window box) are changed from
'offset one' to 'offset zero' and bound to the screen size using:
v->xs = min_t(u16, v->xs - 1, vc->vc_cols - 1);
This has the side effect of converting zero to the limit.
A check I'm adding to min_t() reports that (u16)(v->xs - 1) (etc)
discards signiticant bits (because v->xs is promoted to 'int' before
the addition).
If v->xs is zero (it comes from userspace) it converts -1 to 0xffff.
This is then bounded to 'vc->vc_cols - 1' which will be fine.
Replace with:
v->xs = umin(v->xs - 1, vc->vc_cols - 1);
which again converts a -1 to unsigned - this time to 0xffffffff,
with the same overall effect.
Whether zero is meant to mean the 'maximum size' is unknown.
I can't find any documentation for the ioctl and it pre-dates git.
Detected by an extra check added to min_t().
Signed-off-by: David Laight <david.laight.linux@gmail.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://patch.msgid.link/20251119224140.8616-28-david.laight.linux@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When compiled with -ffunction-sections (e.g., for LTO, livepatch, dead
code elimination, AutoFDO, or Propeller), the startup() function gets
compiled into the .text.startup section (or in some cases
.text.startup.constprop.0 or .text.startup.isra.0).
However, the .text.startup and .text.startup.* sections are also used by
the compiler for __attribute__((constructor)) code.
This naming conflict causes the vmlinux linker script to wrongly place
startup() function code in .init.text, which gets freed during boot.
Some builds have a mix of objects, both with and without
-ffunctions-sections, so it's not possible for the linker script to
disambiguate with #ifdef CONFIG_FUNCTION_SECTIONS or similar. This
means that "startup" unfortunately needs to be prohibited as a function
name.
Rename startup() to startup_hw(). For consistency, also rename its
shutdown() counterpart to shutdown_hw().
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://patch.msgid.link/f0ee750f35c878172cc09916a0724b74e62eadc2.1763669451.git.jpoimboe@kernel.org
When compiled with -ffunction-sections (e.g., for LTO, livepatch, dead
code elimination, AutoFDO, or Propeller), the startup() function gets
compiled into the .text.startup section (or in some cases
.text.startup.constprop.0 or .text.startup.isra.0).
However, the .text.startup and .text.startup.* sections are also used by
the compiler for __attribute__((constructor)) code.
This naming conflict causes the vmlinux linker script to wrongly place
startup() function code in .init.text, which gets freed during boot.
Some builds have a mix of objects, both with and without
-ffunctions-sections, so it's not possible for the linker script to
disambiguate with #ifdef CONFIG_FUNCTION_SECTIONS or similar. This
means that "startup" unfortunately needs to be prohibited as a function
name.
Rename startup() to rs_startup(). For consistency, also rename its
shutdown() counterpart to rs_shutdown().
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://patch.msgid.link/9e56afff5268b0b12b99a8aa9bf244d6ebdcdf47.1763669451.git.jpoimboe@kernel.org
When compiled with -ffunction-sections (e.g., for LTO, livepatch, dead
code elimination, AutoFDO, or Propeller), the startup() function gets
compiled into the .text.startup section (or in some cases
.text.startup.constprop.0 or .text.startup.isra.0).
However, the .text.startup and .text.startup.* sections are also used by
the compiler for __attribute__((constructor)) code.
This naming conflict causes the vmlinux linker script to wrongly place
startup() function code in .init.text, which gets freed during boot.
Some builds have a mix of objects, both with and without
-ffunctions-sections, so it's not possible for the linker script to
disambiguate with #ifdef CONFIG_FUNCTION_SECTIONS or similar. This
means that "startup" unfortunately needs to be prohibited as a function
name.
Rename startup() to icom_startup(). For consistency, also rename its
shutdown() counterpart to icom_shutdown().
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://patch.msgid.link/1aee9ef69f9d40405676712b34f0c397706e7023.1763669451.git.jpoimboe@kernel.org
Inline the contents of sh-sci.h into sh-sci.c and remove the
header file. The header only contained register definitions
and macros used exclusively by the sh-sci driver, making the
separate header unnecessary.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://patch.msgid.link/20251023104313.210989-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check for returned DMA addresses using specialized dma_mapping_error()
helper which is generally recommended for this purpose by
Documentation/core-api/dma-api.rst:
"In some circumstances dma_map_single(), ...
will fail to create a mapping. A driver can check for these errors
by testing the returned DMA address with dma_mapping_error()."
Found via static analysis and this is similar to commit fa0308134d
("ALSA: memalloc: prefer dma_mapping_error() over explicit address checking")
Fixes: 58ac1b3799 ("ARM: PL011: Fix DMA support")
Cc: stable <stable@kernel.org>
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://patch.msgid.link/20251027092053.87937-1-linmq006@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Indicate why lock needs to be asserted when accessing
MSR register, as this is not immediately obvious when looking at this
register in the device datasheet.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20251027142957.1032073-15-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fold some multi-line comments into a single line, taking advantage of the
new 100 line length limit to improve readability and to have uniform style
across driver.
Add missing 's' to SC16IS7XX_MCR_TCRTLR_BIT registers comments.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20251027142957.1032073-14-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to redefine the driver name. Use KBUILD_MODNAME and get
rid of DRV_NAME altogether.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20251027142957.1032073-12-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify macro to_sc16is7xx_one() to only take one parameter, as most
of the time (19) it is called with the "port" structure name. This
improves readability.
For the remaining places where it is called (4), simply use container_of()
locally. This is similar to what is done in other drivers (ex: max310x).
For sc16is7xx_tx_proc(), first assigning "one" variable allows to simplify
"port" variable init.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20251027142957.1032073-10-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sc16is7xx_probe() function is very long. To improve readability, move
port/channel initialization to a separate function.
No functional change intended.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20251027142957.1032073-9-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SPR shares the same address space as TLR and XOFF2. If SPR or TLR were to
be used eventually, this could lead to incorrect read value from the cache.
Prevent this potential bug by declaring SPR/TLR/XOFF2 as volatile.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20251027142957.1032073-8-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Core already prints detailed error messages on ENOMEM errors and drivers
should avoid repeating it.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20251027142957.1032073-7-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Guards can help to make the code more readable, so use them wherever they
do so.
In sc16is7xx_port_irq(), labels and 'rc' locals are eliminated completely.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20251027142957.1032073-6-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to cast from a void * pointer, so remove this cast.
Also remove empty line inavertently added in commit d5078509c8
("serial: sc16is7xx: improve do/while loop in sc16is7xx_irq()") and
change variables order to follow reversed xmas tree.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20251027142957.1032073-5-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rename lock/unlock functions to make it more generic and applicable to both
the Enhanced register set and the Special register set.
Use this new generic function when accessing the Special register set in
sc16is7xx_set_baud(), and when accessing the Enhanced register set in
sc16is7xx_set_termios() and sc16is7xx_probe().
This helps readability and also avoid to make future mistakes when
accessing these obfuscated registers.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20251027142957.1032073-4-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This mutex is used as a lock when accessing registers that share the same
address space, not necessarily EFR registers.
For example, address 0x06 is shared by MSR, TCR and XOFF1 registers,
independently of EFR.
Rename the mutex with a more generic name to avoid misinterpreting its
usage.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20251027142957.1032073-3-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no reference to CONF_MODE_A or CONF_MODE_B in the manufacturer's
datasheet.
Rename register set configuration macros for the LCR register, to better
show their intended usage to select either the Special register set, or the
Enhanced register set.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20251027142957.1032073-2-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add missing kernel-doc entry for the @dlci parameter in
gsm_modem_send_initial_msc(), which fixes the following warning
reported by kernel-doc:
Warning: drivers/tty/n_gsm.c:4175 function parameter 'dlci' not described in 'gsm_modem_send_initial_msc'
Signed-off-by: Kriish Sharma <kriish.sharma2006@gmail.com>
Link: https://patch.msgid.link/20251025161206.795784-1-kriish.sharma2006@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some MediaTek SoCs got a gated UART baud clock, which currently gets
disabled as the clk subsystem believes it would be unused. This results in
the uart freezing right after "clk: Disabling unused clocks" on those
platforms.
Request the baud clock to be prepared and enabled during probe, and to
restore run-time power management capabilities to what it was before commit
e32a83c70c ("serial: 8250-mtk: modify mtk uart power and clock
management") disable and unprepare the baud clock when suspending the UART,
prepare and enable it again when resuming it.
Fixes: e32a83c70c ("serial: 8250-mtk: modify mtk uart power and clock management")
Fixes: b6c7ff2693 ("serial: 8250_mtk: Simplify clock sequencing and runtime PM")
Cc: stable <stable@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://patch.msgid.link/de5197ccc31e1dab0965cabcc11ca92e67246cf6.1758058441.git.daniel@makrotopia.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check the return value of reset_control_deassert() in the probe
function to prevent continuing probe when reset deassertion fails.
Previously, reset_control_deassert() was called without checking its
return value, which could lead to probe continuing even when the
device reset wasn't properly deasserted.
The fix checks the return value and returns an error with dev_err_probe()
if reset deassertion fails, providing better error handling and
diagnostics.
Fixes: acbdad8dd1 ("serial: 8250_dw: simplify optional reset handling")
Cc: stable <stable@kernel.org>
Signed-off-by: Artem Shimko <a.shimko.dev@gmail.com>
Link: https://patch.msgid.link/20251019095131.252848-1-a.shimko.dev@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 43c51bb573 ("sc16is7xx: make sure device is in suspend once
probed") permanently enabled access to the enhanced features in
sc16is7xx_probe(), and it is never disabled after that.
Therefore, remove re-enable of enhanced features in
sc16is7xx_set_baud(). This eliminates a potential useless read + write
cycle each time the baud rate is reconfigured.
Fixes: 43c51bb573 ("sc16is7xx: make sure device is in suspend once probed")
Cc: stable <stable@kernel.org>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20251006142002.177475-1-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Advantech 2-port serial card with PCI vendor=0x13fe and device=0x0018
has a 'XR17V35X' chip installed on the circuit board. Therefore, this
driver can be used instead of theu outdated out-of-tree driver from the
manufacturer.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Cc: stable <stable@kernel.org>
Link: https://patch.msgid.link/20250924134115.2667650-1-fe@dev.tdt.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The receive error handling code is shared between RSCI and all other
SCIF port types, but the RSCI overrun_reg is specified as a memory
offset, while for other SCIF types it is an enum value used to index
into the sci_port_params->regs array, as mentioned above the
sci_serial_in() function.
For RSCI, the overrun_reg is CSR (0x48), causing the sci_getreg() call
inside the sci_handle_fifo_overrun() function to index outside the
bounds of the regs array, which currently has a size of 20, as specified
by SCI_NR_REGS.
Because of this, we end up accessing memory outside of RSCI's
rsci_port_params structure, which, when interpreted as a plat_sci_reg,
happens to have a non-zero size, causing the following WARN when
sci_serial_in() is called, as the accidental size does not match the
supported register sizes.
The existence of the overrun_reg needs to be checked because
SCIx_SH3_SCIF_REGTYPE has overrun_reg set to SCLSR, but SCLSR is not
present in the regs array.
Avoid calling sci_getreg() for port types which don't use standard
register handling.
Use the ops->read_reg() and ops->write_reg() functions to properly read
and write registers for RSCI, and change the type of the status variable
to accommodate the 32-bit CSR register.
sci_getreg() and sci_serial_in() are also called with overrun_reg in the
sci_mpxed_interrupt() interrupt handler, but that code path is not used
for RSCI, as it does not have a muxed interrupt.
------------[ cut here ]------------
Invalid register access
WARNING: CPU: 0 PID: 0 at drivers/tty/serial/sh-sci.c:522 sci_serial_in+0x38/0xac
Modules linked in: renesas_usbhs at24 rzt2h_adc industrialio_adc sha256 cfg80211 bluetooth ecdh_generic ecc rfkill fuse drm backlight ipv6
CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted 6.17.0-rc1+ #30 PREEMPT
Hardware name: Renesas RZ/T2H EVK Board based on r9a09g077m44 (DT)
pstate: 604000c5 (nZCv daIF +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : sci_serial_in+0x38/0xac
lr : sci_serial_in+0x38/0xac
sp : ffff800080003e80
x29: ffff800080003e80 x28: ffff800082195b80 x27: 000000000000000d
x26: ffff8000821956d0 x25: 0000000000000000 x24: ffff800082195b80
x23: ffff000180e0d800 x22: 0000000000000010 x21: 0000000000000000
x20: 0000000000000010 x19: ffff000180e72000 x18: 000000000000000a
x17: ffff8002bcee7000 x16: ffff800080000000 x15: 0720072007200720
x14: 0720072007200720 x13: 0720072007200720 x12: 0720072007200720
x11: 0000000000000058 x10: 0000000000000018 x9 : ffff8000821a6a48
x8 : 0000000000057fa8 x7 : 0000000000000406 x6 : ffff8000821fea48
x5 : ffff00033ef88408 x4 : ffff8002bcee7000 x3 : ffff800082195b80
x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffff800082195b80
Call trace:
sci_serial_in+0x38/0xac (P)
sci_handle_fifo_overrun.isra.0+0x70/0x134
sci_er_interrupt+0x50/0x39c
__handle_irq_event_percpu+0x48/0x140
handle_irq_event+0x44/0xb0
handle_fasteoi_irq+0xf4/0x1a0
handle_irq_desc+0x34/0x58
generic_handle_domain_irq+0x1c/0x28
gic_handle_irq+0x4c/0x140
call_on_irq_stack+0x30/0x48
do_interrupt_handler+0x80/0x84
el1_interrupt+0x34/0x68
el1h_64_irq_handler+0x18/0x24
el1h_64_irq+0x6c/0x70
default_idle_call+0x28/0x58 (P)
do_idle+0x1f8/0x250
cpu_startup_entry+0x34/0x3c
rest_init+0xd8/0xe0
console_on_rootfs+0x0/0x6c
__primary_switched+0x88/0x90
---[ end trace 0000000000000000 ]---
Cc: stable <stable@kernel.org>
Fixes: 0666e3fe95 ("serial: sh-sci: Add support for RZ/T2H SCI")
Signed-off-by: Cosmin Tanislav <cosmin-gabriel.tanislav.xa@renesas.com>
Link: https://patch.msgid.link/20250923154707.1089900-1-cosmin-gabriel.tanislav.xa@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the '8250_exar' module is loaded into the kernel, a kernel trace
with 'WARN_ON(legacy_iomap_table[bar])' is dumped to the console,
because the old pci table mapping is still used in '8250_pcilib'.
The old function have been deprecated in commit e354bb84a4 ("PCI:
Deprecate pcim_iomap_table(), pcim_iomap_regions_request_all()").
The remapping already takes or must take place in the driver that calls
the function 'serial8250_pci_setup_port()'. The remapping should only be
called once via 'pcim_iomap()'. Therefore the remapping moved to the
caller of 'serial8250_pci_setup_port()'.
To replace the outdated/legacy iomap_table processing in '8250_pcilib' the
function signature of 'serial8250_pci_setup_port()' has been extended with
an already iomapped address value. So this can be used directly without
io mapping again.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://patch.msgid.link/20250930072743.791580-1-fe@dev.tdt.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current imx uart wakeup event would not report itself as wakeup source
through sysfs. Add pm_wakeup_event() to support it.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20251002045259.2725461-3-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the i.MX UART driver enables wake-related registers for all
UART devices by default. However, this is unnecessary for devices that
are not configured as wakeup sources. To address this, add a
device_may_wakeup() check before configuring the UART wake-related
registers.
Fixes: db1a9b5500 ("tty: serial: imx: Allow UART to be a source for wakeup")
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20251002045259.2725461-2-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current lpuart wakeup event would not report itself as wakeup source
through sysfs. Add pm_wakeup_event() to support it.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20250924025607.2515833-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is a single driver fix for the qcom_geni_serial driver for
6.18-rc1. It has been in my tree for weeks, but missed being sent to
you for 6.17-final due to travel on my side.
This fixes a reported regression for this driver that prevents 6.17 from
working properly on this platform.
It has been in linux-next for many weeks with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCaOUQrA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymmXwCgj5hLg2MHRlvZ+aCD0K/S2Qt4eqEAn32POqfZ
UntJ9O23oHW1+RmAvBB7
=zKb3
-----END PGP SIGNATURE-----
Merge tag 'tty-6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty driver fix from Greg KH:
"Here is a single driver fix for the qcom_geni_serial driver. It has
been in my tree for weeks, but missed being sent to you for 6.17-final
due to travel on my side.
This fixes a reported regression for this driver that prevents 6.17
from working properly on this platform.
It has been in linux-next for many weeks with no reported issues"
* tag 'tty-6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: qcom-geni: Fix blocked task
Here are some small updates for tty/serial drivers for 6.18-rc1.
Not many changes overall, just the usual:
- abi cleanups and reworking of the tty functions by Jiri by adding
console lock guard logic
- 8250_platform driver updates
- qcom-geni driver updates
- other minor serial driver updates
- some more vt escape codes added
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCaOEnLA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymLswCfa2SDyet0vn5oIrto+0WG9Wxlp3AAoMaDzkqG
DX2YoOI1L0miAQfQ9IhZ
=0V8V
-----END PGP SIGNATURE-----
Merge tag 'tty-6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here are some small updates for tty/serial drivers for 6.18-rc1.
Not many changes overall, just the usual:
- abi cleanups and reworking of the tty functions by Jiri by adding
console lock guard logic
- 8250_platform driver updates
- qcom-geni driver updates
- other minor serial driver updates
- some more vt escape codes added
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (43 commits)
tty: serial: fix help message for SERIAL_CPM
serial: 8250: omap: Support wakeup pinctrl state on suspend
dt-bindings: serial: 8250_omap: Add wakeup pinctrl state
serial: max310x: improve interrupt handling
vt: move vc_saved_screen to within tty allocated judgment
Revert "m68k: make HPDCA and HPAPCI bools"
tty: remove redundant condition checks
tty/vt: Add missing return value for VT_RESIZE in vt_ioctl()
vt: remove redundant check on vc_mode in con_font_set()
serial: qcom-geni: Add DFS clock mode support to GENI UART driver
m68k: make HPDCA and HPAPCI bools
tty: n_gsm: Don't block input queue by waiting MSC
serial: qcom-geni: Fix off-by-one error in ida_alloc_range()
serdev: Drop dev_pm_domain_detach() call
serial: sc16is7xx: drop redundant conversion to bool
vt: add support for smput/rmput escape codes
serial: stm32: allow selecting console when the driver is module
serial: 8250_core: fix coding style issue
tty: serial: Modify the use of dev_err_probe()
s390/char/con3270: use tty_port_tty guard()
...
Lots of platform specific updates for Qualcomm SoCs, including a
new TEE subsystem driver for the Qualcomm QTEE firmware interface.
Added support for the Apple A11 SoC in drivers that are shared with the
M1/M2 series, among more updates for those.
Smaller platform specific driver updates for Renesas, ASpeed, Broadcom,
Nvidia, Mediatek, Amlogic, TI, Allwinner, and Freescale SoCs.
Driver updates in the cache controller, memory controller and reset
controller subsystems.
SCMI firmware updates to add more features and improve robustness.
This includes support for having multiple SCMI providers in a single
system.
TEE subsystem support for protected DMA-bufs, allowing hardware to
access memory areas that managed by the kernel but remain inaccessible
from the CPU in EL1/EL0.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEo6/YBQwIrVS28WGKmmx57+YAGNkFAmjdpaoACgkQmmx57+YA
GNnBXA//QgmFXYGG7QfB825mt0orKZxpfpLcwvqO7hkWgbXtl7Gokw2lGYN6bwLu
zvY4MQ/bVoZ8R5uTVmuaSHBRsttSen8mBf+V0vzsBM/DRRVxvIN/7TESrY3J7Dtx
J5syHKIBiUtdkDebWWC6jIElczIBItsd03Ln4Xjjt8Vas5YOO4n44zFrPo+FwlN/
I6D2K86AiNZTtUCDMtB6VfJ6YtjYBWcWnJm7FXw/vE8FAXdZUnNWnZ8hbdQ5GaME
JZGepUhONaOMUoGNZNaDGw511RdPhYzPjj9rCsIx2qdsRO9/4tJ8ccpW2aUMYh8c
nA6w8Hj8jCwco6aYYrDUDV9uRtURDrmyJgTJBNLU05e/L+MuJ3IZNlzHFWlsxIAE
vhyTdmg/P04ClQyixCl67IH/66F/0smX9C+1761LrD7GTdfR92KPl5W6q+DPBg/x
yf+s2p3+f7ItV5XobKOrbf3w0xazeDb5o/EK8BufMx9vSe9bpzJ0gOf0CmNXEpyZ
owAhbh6wXX1YwPcyA9LHv6gthyJwc/3fLu49ggMZP2rU01ccKOYn9H0cr7C8NVmy
wEpJR0lp5aSw2oRkPkxB6sFmUohcpr8/OXGGJuvCXkYsUY1BEup4lewvbIWK4WoE
c84kbbaHsjgFhe3IRlQw3G4KLYQT3jRtF7fH+gPx556BcI6K+lg=
=mcZR
-----END PGP SIGNATURE-----
Merge tag 'soc-drivers-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC driver updates from Arnd Bergmann:
"Lots of platform specific updates for Qualcomm SoCs, including a new
TEE subsystem driver for the Qualcomm QTEE firmware interface.
Added support for the Apple A11 SoC in drivers that are shared with
the M1/M2 series, among more updates for those.
Smaller platform specific driver updates for Renesas, ASpeed,
Broadcom, Nvidia, Mediatek, Amlogic, TI, Allwinner, and Freescale
SoCs.
Driver updates in the cache controller, memory controller and reset
controller subsystems.
SCMI firmware updates to add more features and improve robustness.
This includes support for having multiple SCMI providers in a single
system.
TEE subsystem support for protected DMA-bufs, allowing hardware to
access memory areas that managed by the kernel but remain inaccessible
from the CPU in EL1/EL0"
* tag 'soc-drivers-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (139 commits)
soc/fsl/qbman: Use for_each_online_cpu() instead of for_each_cpu()
soc: fsl: qe: Drop legacy-of-mm-gpiochip.h header from GPIO driver
soc: fsl: qe: Change GPIO driver to a proper platform driver
tee: fix register_shm_helper()
pmdomain: apple: Add "apple,t8103-pmgr-pwrstate"
dt-bindings: spmi: Add Apple A11 and T2 compatible
serial: qcom-geni: Load UART qup Firmware from linux side
spi: geni-qcom: Load spi qup Firmware from linux side
i2c: qcom-geni: Load i2c qup Firmware from linux side
soc: qcom: geni-se: Add support to load QUP SE Firmware via Linux subsystem
soc: qcom: geni-se: Cleanup register defines and update copyright
dt-bindings: qcom: se-common: Add QUP Peripheral-specific properties for I2C, SPI, and SERIAL bus
Documentation: tee: Add Qualcomm TEE driver
tee: qcom: enable TEE_IOC_SHM_ALLOC ioctl
tee: qcom: add primordial object
tee: add Qualcomm TEE driver
tee: increase TEE_MAX_ARG_SIZE to 4096
tee: add TEE_IOCTL_PARAM_ATTR_TYPE_OBJREF
tee: add TEE_IOCTL_PARAM_ATTR_TYPE_UBUF
tee: add close_context to TEE driver operation
...
Introduce support for loading firmware into the QUP serial engines from
Linux, which allows deferring selection of which protocol (uart, i2c,
spi, etc) a given SE should have until the OS loads.
Also introduce the "object invoke" interface in the SCM driver, to
provide interface to the Qualcomm TEE driver.
-----BEGIN PGP SIGNATURE-----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=TulG
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=JuVO
-----END PGP SIGNATURE-----
Merge tag 'qcom-drivers-for-6.18-2' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into soc/drivers
More Qualcomm device driver updates for v6.18
Introduce support for loading firmware into the QUP serial engines from
Linux, which allows deferring selection of which protocol (uart, i2c,
spi, etc) a given SE should have until the OS loads.
Also introduce the "object invoke" interface in the SCM driver, to
provide interface to the Qualcomm TEE driver.
* tag 'qcom-drivers-for-6.18-2' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
serial: qcom-geni: Load UART qup Firmware from linux side
spi: geni-qcom: Load spi qup Firmware from linux side
i2c: qcom-geni: Load i2c qup Firmware from linux side
soc: qcom: geni-se: Add support to load QUP SE Firmware via Linux subsystem
soc: qcom: geni-se: Cleanup register defines and update copyright
dt-bindings: qcom: se-common: Add QUP Peripheral-specific properties for I2C, SPI, and SERIAL bus
firmware: qcom: scm: add support for object invocation
firmware: qcom: tzmem: export shm_bridge create/delete
Link: https://lore.kernel.org/r/20250921020225.595403-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add provision to load firmware of Serial engine for UART protocol from
Linux Execution Environment on running on APPS processor.
Co-developed-by: Mukesh Kumar Savaliya <mukesh.savaliya@oss.qualcomm.com>
Signed-off-by: Mukesh Kumar Savaliya <mukesh.savaliya@oss.qualcomm.com>
Signed-off-by: Viken Dadhaniya <viken.dadhaniya@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250911043256.3523057-7-viken.dadhaniya@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Revert commit 1afa70632c ("serial: qcom-geni: Enable PM runtime for
serial driver") and its dependent commit 86fa39dd6f ("serial:
qcom-geni: Enable Serial on SA8255p Qualcomm platforms") because the
first one causes regression - hang task on Qualcomm RB1 board (QRB2210)
and unable to use serial at all during normal boot:
INFO: task kworker/u16:0:12 blocked for more than 42 seconds.
Not tainted 6.17.0-rc1-00004-g53e760d89498 #9
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:kworker/u16:0 state:D stack:0 pid:12 tgid:12 ppid:2 task_flags:0x4208060 flags:0x00000010
Workqueue: async async_run_entry_fn
Call trace:
__switch_to+0xe8/0x1a0 (T)
__schedule+0x290/0x7c0
schedule+0x34/0x118
rpm_resume+0x14c/0x66c
rpm_resume+0x2a4/0x66c
rpm_resume+0x2a4/0x66c
rpm_resume+0x2a4/0x66c
__pm_runtime_resume+0x50/0x9c
__driver_probe_device+0x58/0x120
driver_probe_device+0x3c/0x154
__driver_attach_async_helper+0x4c/0xc0
async_run_entry_fn+0x34/0xe0
process_one_work+0x148/0x290
worker_thread+0x2c4/0x3e0
kthread+0x118/0x1c0
ret_from_fork+0x10/0x20
The issue was reported on 12th of August and was ignored by author of
commits introducing issue for two weeks. Only after complaining author
produced a fix which did not work, so if original commits cannot be
reliably fixed for 5 weeks, they obviously are buggy and need to be
dropped.
Fixes: 1afa70632c ("serial: qcom-geni: Enable PM runtime for serial driver")
Reported-by: Alexey Klimov <alexey.klimov@linaro.org>
Closes: https://lore.kernel.org/all/DC0D53ZTNOBU.E8LSD5E5Z8TX@linaro.org/
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Alexey Klimov <alexey.klimov@linaro.org>
Reviewed-by: Alexey Klimov <alexey.klimov@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20250917010437.129912-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Running checkpatch reported error extra whitespace at the
end of help message for SERIAL_CPM menu entry
Signed-off-by: Arturs Artamonovs <Arturs.Artamonovs@analog.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This update includes:
- basic infrastructure support for Microchip LAN969x SoC
- SoC ARCH symbols (existing SparX-5, new LAN969x) under the
ARCH_MICROCHIP hidden symbol (already in use by AT91 in 6.17)
- addition of that new symbol for drivers that are shared by
Microchip SoC-s now and in the future
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQ5TRCVIBiyi/S+BG4fOrpwrNPNDAUCaMgFkQAKCRAfOrpwrNPN
DFEbAQDg6iMOzL+C2tqu9eTfBZv9DCKcbfVFeHnwGqSbH8L/WgD/ZOq4UKIBMXpA
MGtwDDkDKBPVv3clF461/nS+VtAOaAE=
=upTs
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=zZ1l
-----END PGP SIGNATURE-----
Merge tag 'microchip-soc-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into soc/drivers
Microchip ARM64 SoC updates for v6.18:
This update includes:
- basic infrastructure support for Microchip LAN969x SoC
- SoC ARCH symbols (existing SparX-5, new LAN969x) under the
ARCH_MICROCHIP hidden symbol (already in use by AT91 in 6.17)
- addition of that new symbol for drivers that are shared by
Microchip SoC-s now and in the future
* tag 'microchip-soc-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
crypto: atmel-aes: make it selectable for ARCH_MICROCHIP
char: hw_random: atmel: make it selectable for ARCH_MICROCHIP
i2c: at91: make it selectable for ARCH_MICROCHIP
spi: atmel: make it selectable for ARCH_MICROCHIP
tty: serial: atmel: make it selectable for ARCH_MICROCHIP
mfd: at91-usart: Make it selectable for ARCH_MICROCHIP
arm64: lan969x: Add support for Microchip LAN969x SoC
arm64: Add config for Microchip SoC platforms
Link: https://lore.kernel.org/r/20250915123548.13722-1-nicolas.ferre@microchip.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Here are some small tty and serial driver fixes for 6.17-rc6 that
resolve some reported problems. Included in here are:
- 8250 driver dt bindings fixes
- broadcom serial driver binding fixes
- hvc_console bugfix
- xilinx serial driver bugfix
- sc16is7xx serial driver bugfix
All of these have been in linux-next for the past week with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCaMar1w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yk8AQCgx9deB0WhbxP/+3sVJ+0swX/bWdoAn3hCCy8f
P+QkteZ02Mmz25DS+gMB
=3mTh
-----END PGP SIGNATURE-----
Merge tag 'tty-6.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some small tty and serial driver fixes for 6.17-rc6 that
resolve some reported problems. Included in here are:
- 8250 driver dt bindings fixes
- broadcom serial driver binding fixes
- hvc_console bugfix
- xilinx serial driver bugfix
- sc16is7xx serial driver bugfix
All of these have been in linux-next for the past week with no
reported issues"
* tag 'tty-6.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: xilinx_uartps: read reg size from DTS
tty: hvc_console: Call hvc_kick in hvc_write unconditionally
dt-bindings: serial: 8250: allow "main" and "uart" as clock names
dt-bindings: serial: 8250: move a constraint
dt-bindings: serial: brcm,bcm7271-uart: Constrain clocks
serial: sc16is7xx: fix bug in flow control levels init
UART can be used as a wakeup source for am62 from suspend to ram states.
To enable wakeup from UART am62 requires a wakeup flag being set in the
pinctrl.
If the device is marked as wakeup enabled, select the 'wakeup' pinctrl
state on suspend and restore the default pinctrl state on resume.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Signed-off-by: Kendall Willis <k-willis@ti.com>
Link: https://lore.kernel.org/r/20250910-uart-daisy-chain-8250-omap-v2-2-e90d44c1a9ac@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When there is a heavy load of receiving characters to all
four UART's, the warning 'Hardware RX FIFO overrun' is
sometimes detected.
The current implementation always service first the highest UART
until no more interrupt and then service another UART
(ex: UART3 will be serviced for as long as there are interrupts
for it, then UART2, etc).
This commit handle all individual interrupt sources before
reading the global IRQ register again.
This commit has also a nice side-effect of improving the efficiency
of the driver by reducing the number of reads of the global
IRQ register.
Signed-off-by: Tapio Reijonen <tapio.reijonen@vaisala.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Reviewed-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20250908-master-max310x-improve-interrupt-handling-v3-1-91985e82ba39@vaisala.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
LAN969x uses the Atmel USART serial, so make it selectable for
ARCH_MICROCHIP to avoid needing to update depends in future if other
Microchip SoC-s use it as well.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Current implementation uses `CDNS_UART_REGISTER_SPACE(0x1000)`
for request_mem_region() and ioremap() in cdns_uart_request_port() API.
The cadence/xilinx IP has register space defined from offset 0x0 to 0x48.
It also mentions that the register map is defined as [6:0]. So, the upper
region may/maynot be used based on the IP integration.
In Axiado AX3000 SoC two UART instances are defined
0x100 apart. That is creating issue in some other instance due to overlap
with addresses.
Since, this address space is already being defined in the
devicetree, use the same when requesting the register space.
Fixes: 1f70557790 ("arm64: dts: axiado: Add initial support for AX3000 SoC and eval board")
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Harshit Shah <hshah@axiado.com>
Link: https://lore.kernel.org/r/20250902-xilinx-uartps-reg-size-v3-1-d11cfa7258e3@axiado.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In vt_ioctl(), the handler for VT_RESIZE always returns 0, which prevents
users from detecting errors. Add the missing return value so that errors
can be properly reported to users like vt_resizex().
Signed-off-by: Zizhi Wo <wozizhi@huaweicloud.com>
Link: https://lore.kernel.org/r/20250904023955.3892120-1-wozizhi@huaweicloud.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previous commit edab558feb ("vt: sort out locking for font handling")
move the vc_mode check into console_lock protect, but forget to remove the
old check in con_font_set(). Just remove the redundant check.
Signed-off-by: Wang Liang <wangliang74@huawei.com>
Link: https://lore.kernel.org/r/20250904023345.13731-1-wangliang74@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GENI UART driver currently supports only non-DFS (Dynamic Frequency
Scaling) mode for source frequency selection. However, to operate correctly
in DFS mode, the GENI SCLK register must be programmed with the appropriate
DFS index. Failing to do so can result in incorrect frequency selection
Add support for Dynamic Frequency Scaling (DFS) mode in the GENI UART
driver by configuring the GENI_CLK_SEL register with the appropriate DFS
index. This ensures correct frequency selection when operating in DFS mode.
Replace the UART driver-specific logic for clock selection with the GENI
common driver function to obtain the desired frequency and corresponding
clock index. This improves maintainability and consistency across
GENI-based drivers.
Signed-off-by: Viken Dadhaniya <viken.dadhaniya@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250903063136.3015237-1-viken.dadhaniya@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently gsm_queue() processes incoming frames and when opening
a DLC channel it calls gsm_dlci_open() which calls gsm_modem_update().
If basic mode is used it calls gsm_modem_upd_via_msc() and it
cannot block the input queue by waiting the response to come
into the same input queue.
Instead allow sending Modem Status Command without waiting for remote
end to respond. Define a new function gsm_modem_send_initial_msc()
for this purpose. As MSC is only valid for basic encoding, it does
not do anything for advanced or when convergence layer type 2 is used.
Fixes: 4847380250 ("tty: n_gsm: fix missing update of modem controls after DLCI open")
Signed-off-by: Seppo Takalo <seppo.takalo@nordicsemi.no>
Link: https://lore.kernel.org/r/20250827123221.1148666-1-seppo.takalo@nordicsemi.no
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ida_alloc_range() function expects an inclusive range, meaning both
the start and end values are valid allocation targets. Passing nr_ports
as the upper bound allows allocation of an ID equal to nr_ports, which
is out of bounds when used as an index into the port array.
Fix this by subtracting 1 from nr_ports in both calls to ida_alloc_range(),
ensuring the allocated ID stays within the valid range
[start, nr_ports - 1].
This prevents potential out-of-bounds access when the allocated ID is used
as an index.
Fixes: 9391ab1ed9 ("serial: qcom-geni: Make UART port count configurable via Kconfig")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/r/202508180815.R2nDyajs-lkp@intel.com/
Signed-off-by: Zong Jiang <quic_zongjian@quicinc.com>
Link: https://lore.kernel.org/r/20250827120319.1682835-1-quic_zongjian@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Starting with commit f99508074e ("PM: domains: Detach on
device_unbind_cleanup()"), there is no longer a need to call
dev_pm_domain_detach() in the bus remove function. The
device_unbind_cleanup() function now handles this to avoid
invoking devres cleanup handlers while the PM domain is
powered off, which could otherwise lead to failures as
described in the above-mentioned commit.
Drop the explicit dev_pm_domain_detach() call and rely instead
on the flags passed to dev_pm_domain_attach() to power off the
domain.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20250827101747.928265-1-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The result of integer comparison already evaluates to bool. No need for
explicit conversion.
Signed-off-by: Xichao Zhao <zhao.xichao@vivo.com>
Link: https://lore.kernel.org/r/20250827024514.76149-1-zhao.xichao@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Support "\e[?1049h" and "\e[?1049l" escape codes.
This patch allows programs to enter and leave alternate screens.
This feature is widely available in graphical terminal emulators and mostly
used by fullscreen terminal-based user interfaces such as text editors.
Most editors such as vim and nano assume this escape code in not supported
and will not try to print the escape sequence if TERM=linux.
To try out this patch, run `TERM=xterm-256color vim` inside a VT.
Signed-off-by: Calixte Pernot <calixte.pernot@grenoble-inp.org>
Link: https://lore.kernel.org/r/20250825125607.2478-3-calixte.pernot@grenoble-inp.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dev_err_probe() doesn't do anything when error is '-ENOMEM'.
Make the following two changes:
(1) Replace -ENOMEM with -ENOSPC in max3100_probe().
(2) Just return -ENOMEM instead in max310x_probe().
Signed-off-by: Xichao Zhao <zhao.xichao@vivo.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250819120927.607744-1-zhao.xichao@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After hvc_write completes, call hvc_kick also in the case the output
buffer has been drained, to ensure tty_wakeup gets called.
This fixes that functions which wait for a drained buffer got stuck
occasionally.
Cc: stable <stable@kernel.org>
Closes: https://bugzilla.opensuse.org/show_bug.cgi?id=1230062
Signed-off-by: Fabian Vogt <fvogt@suse.de>
Link: https://lore.kernel.org/r/2011735.PYKUYFuaPT@fvogt-thinkpad
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Having all the new guards, use them in the vt code. This improves
readability, makes error handling easier, and marks locked portions of
code explicit.
A local free_page_ptr __free guard is introduced for
__get_free_page/free_page (with proper casts). This could be made public
in include/. But I am not sure if there are more possible users, so
keeping completely private here.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250814072456.182853-16-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Having all the new guards, use them in the 8250_rsa code. This improves
readability, makes error handling easier, and marks locked portions of
code explicit.
The new __free()-annotated declarations are moved to the allocation points
as is preferred:
https://lore.kernel.org/all/CAHk-=wjvh_LUpa=864joG2JJXs3+viO-kLzLidR2JLyMr4MNwA@mail.gmail.com/
Except font_data in con_font_get(). The scope in there would not match
the expected lifetime. But the declaration is moved closer.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250814072456.182853-15-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Having all the new guards, use them in the 8250_rsa code. This improves
readability, makes error handling easier, and marks locked portions of
code explicit.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250814072456.182853-14-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Having all the new guards, use them in the 8250_omap code. This improves
readability, makes error handling easier, and marks locked portions of
code explicit.
For this to work, UART_CAP_RPM has to be set to up->capabilities a bit
earlier.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250814072456.182853-13-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To use guard()s easily in omap_8250_set_termios(), split it into atomic
and non-atomic part. The former can be easily guarded -- without a need
of indenting or moving code.
omap_8250_set_termios() would likely profit from a cleanup similar to
one in serial8250_do_set_termios() in commit cdc4a3e0b2 ("serial:
8250: extract serial8250_set_fcr()") and earlier.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250814072456.182853-12-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Having all the new guards, use them in the 8250 code. This improves
readability, makes error handling easier, and marks locked portions of
code explicit.
serial_unlink_irq_chain() is done separately here because with the
guard() used, those BUG_ON()s can be switched WARN_ON()s as we can
actually handle the conditions and return (despite something went really
wrong).
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250814072456.182853-11-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Having all the new guards, use them in the 8250 code. This improves
readability, makes error handling easier, and marks locked portions of
code explicit.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250814072456.182853-10-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Having all the new guards, use them in the serial_core code. This
improves readability, makes error handling easier, and marks locked
portions of code explicit.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250814072456.182853-9-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Having all the new guards, use them in the mxser code. This improves
readability, makes error handling easier, and marks locked portions of
code explicit.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250814072456.182853-8-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use scoped_guard() and reorder the function. This is done separately
from the other changes, as it is slighly more intrusive: scoped_guard()
handles the have-tty case and returns. The non-tty case is done at the
end of the function.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250814072456.182853-7-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Having all the new guards, use them in the tty_port code. This improves
readability, makes error handling easier, and marks locked portions of
code explicit.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250814072456.182853-6-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Having this, guards like these work:
guard(serial8250_rpm)(up);
or
scoped_guard(serial8250_rpm, up) {
...
}
See e.g. "serial: 8250: use guard()s" later in this series.
And make them available to anyone (EXPORT + put in 8250.h) as drivers
open code this anyway.
The _tx ones are not defined as they would have no user.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250814072456.182853-5-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When trying to set MCR[2], XON1 is incorrectly accessed instead. And when
writing to the TCR register to configure flow control levels, we are
incorrectly writing to the MSR register. The default value of $00 is then
used for TCR, which means that selectable trigger levels in FCR are used
in place of TCR.
TCR/TLR access requires EFR[4] (enable enhanced functions) and MCR[2]
to be set. EFR[4] is already set in probe().
MCR access requires LCR[7] to be zero.
Since LCR is set to $BF when trying to set MCR[2], XON1 is incorrectly
accessed instead because MCR shares the same address space as XON1.
Since MCR[2] is unmodified and still zero, when writing to TCR we are in
fact writing to MSR because TCR/TLR registers share the same address space
as MSR/SPR.
Fix by first removing useless reconfiguration of EFR[4] (enable enhanced
functions), as it is already enabled in sc16is7xx_probe() since commit
43c51bb573 ("sc16is7xx: make sure device is in suspend once probed").
Now LCR is $00, which means that MCR access is enabled.
Also remove regcache_cache_bypass() calls since we no longer access the
enhanced registers set, and TCR is already declared as volatile (in fact
by declaring MSR as volatile, which shares the same address).
Finally disable access to TCR/TLR registers after modifying them by
clearing MCR[2].
Note: the comment about "... and internal clock div" is wrong and can be
ignored/removed as access to internal clock div registers (DLL/DLH)
is permitted only when LCR[7] is logic 1, not when enhanced features
is enabled. And DLL/DLH access is not needed in sc16is7xx_startup().
Fixes: dfeae619d7 ("serial: sc16is7xx")
Cc: stable@vger.kernel.org
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20250731124451.1108864-1-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace the hardcoded GENI_UART_PORTS macro with a new Kconfig option
SERIAL_QCOM_GENI_UART_PORTS to allow platforms to configure the maximum
number of UART ports supported by the driver at build time.
This improves flexibility for platforms that require more than the
previously fixed number of UART ports, and avoids unnecessary allocation
for unused ports.
Signed-off-by: Zong Jiang <quic_zongjian@quicinc.com>
Link: https://lore.kernel.org/r/20250812054819.3748649-3-quic_zongjian@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace the static allocation of UART ports with dynamic allocation
using devm_kzalloc. This change removes the fixed-size array and instead
allocates each UART port structure on demand during probe, improving
memory efficiency and scalability.
Signed-off-by: Zong Jiang <quic_zongjian@quicinc.com>
Link: https://lore.kernel.org/r/20250812054819.3748649-2-quic_zongjian@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The round_rate() clk ops is deprecated, so migrate this driver from
round_rate() to determine_rate() using the Coccinelle semantic patch
appended to the "under-the-cut" portion of the patch.
Signed-off-by: Brian Masney <bmasney@redhat.com>
Link: https://lore.kernel.org/r/20250810-tty-round-rate-v1-1-849009f3bdfd@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function serial8250_probe_platform() in 8250_platform.c triggered a
frame size warning:
drivers/tty/serial/8250/8250_platform.c: In function ‘serial8250_probe_platform.isra’:
drivers/tty/serial/8250/8250_platform.c:201:1: warning: the frame size of 1184 bytes is larger than 1024 bytes [-Wframe-larger-than=]
This patch reduces the stack usage by dynamically allocating the
`uart` structure using kzalloc(), rather than placing it on
the stack. This eliminates the overflow warning and improves kernel
robustness.
Signed-off-by: Abinash Singh <abinashsinghlalotra@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250806215134.4921-3-abinashsinghlalotra@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function serial8250_probe_acpi() in 8250_platform.c triggered a
frame size warning:
drivers/tty/serial/8250/8250_platform.c: In function ‘serial8250_probe_acpi’:
drivers/tty/serial/8250/8250_platform.c:152:1: warning: the frame size of 1160 bytes is larger than 1024 bytes [-Wframe-larger-than=]
This patch reduces the stack usage by dynamically allocating the
`uart` structure using kzalloc(), rather than placing it on
the stack. This eliminates the overflow warning and improves kernel
robustness.
Signed-off-by: Abinash Singh <abinashsinghlalotra@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250806215134.4921-2-abinashsinghlalotra@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit 84a9582fd2 ("serial: core: Start managing serial controllers
to enable runtime PM") serial drivers need to provide a device in
struct uart_port.dev otherwise an oops happens. To fix this issue
for ip22zilog driver switch driver to a platform driver and setup
the serial device in sgi-ip22 code.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Link: https://lore.kernel.org/r/20250725134018.136113-1-tsbogend@alpha.franken.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This code checks if (write) is true twice in a row. It's more
readable to delete the first check.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/aJNAhHtKkhWjosDV@stanley.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Christoph suggested that the explicit _GPL_ can be dropped from the
module namespace export macro, as it's intended for in-tree modules
only. It would be possible to restrict it technically, but it was
pointed out [2] that some cases of using an out-of-tree build of an
in-tree module with the same name are legitimate. But in that case those
also have to be GPL anyway so it's unnecessary to spell it out in the
macro name.
Link: https://lore.kernel.org/all/aFleJN_fE-RbSoFD@infradead.org/ [1]
Link: https://lore.kernel.org/all/CAK7LNATRkZHwJGpojCnvdiaoDnP%2BaeUXgdey5sb_8muzdWTMkA@mail.gmail.com/ [2]
Suggested-by: Christoph Hellwig <hch@infradead.org>
Reviewed-by: Shivank Garg <shivankg@amd.com>
Acked-by: David Hildenbrand <david@redhat.com>
Acked-by: Nicolas Schier <n.schier@avm.de>
Reviewed-by: Daniel Gomez <da.gomez@samsung.com>
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Link: https://lore.kernel.org/20250808-export_modules-v4-1-426945bcc5e1@suse.cz
Signed-off-by: Christian Brauner <brauner@kernel.org>
The conversion of all GPIO drivers to using the .set_rv() and
.set_multiple_rv() callbacks from struct gpio_chip (which - unlike their
predecessors - return an integer and allow the controller drivers to
indicate failures to users) is now complete and the legacy ones have
been removed. Rename the new callbacks back to their original names in
one sweeping change.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
* Move sysctls out of the kern_table array
This is the final move of ctl_tables into their respective subsystems. Only 5
(out of the original 50) will remain in kernel/sysctl.c file; these handle
either sysctl or common arch variables.
By decentralizing sysctl registrations, subsystem maintainers regain control
over their sysctl interfaces, improving maintainability and reducing the
likelihood of merge conflicts.
* docs: Remove false positives from check-sysctl-docs
Stopped falsely identifying sysctls as undocumented or unimplemented in the
check-sysctl-docs script. This script can now be used to automatically
identify if documentation is missing.
* Testing
All these have been in linux-next since rc3, giving them a solid 3 to 4 weeks
worth of testing. Additionally, sysctl selftests and kunit were also run
locally on my x86_64
-----BEGIN PGP SIGNATURE-----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=R369
-----END PGP SIGNATURE-----
Merge tag 'sysctl-6.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/sysctl/sysctl
Pull sysctl updates from Joel Granados:
- Move sysctls out of the kern_table array
This is the final move of ctl_tables into their respective
subsystems. Only 5 (out of the original 50) will remain in
kernel/sysctl.c file; these handle either sysctl or common arch
variables.
By decentralizing sysctl registrations, subsystem maintainers regain
control over their sysctl interfaces, improving maintainability and
reducing the likelihood of merge conflicts.
- docs: Remove false positives from check-sysctl-docs
Stopped falsely identifying sysctls as undocumented or unimplemented
in the check-sysctl-docs script. This script can now be used to
automatically identify if documentation is missing.
* tag 'sysctl-6.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/sysctl/sysctl: (23 commits)
docs: Downgrade arm64 & riscv from titles to comment
docs: Replace spaces with tabs in check-sysctl-docs
docs: Remove colon from ctltable title in vm.rst
docs: Add awk section for ucount sysctl entries
docs: Use skiplist when checking sysctl admin-guide
docs: nixify check-sysctl-docs
sysctl: rename kern_table -> sysctl_subsys_table
kernel/sys.c: Move overflow{uid,gid} sysctl into kernel/sys.c
uevent: mv uevent_helper into kobject_uevent.c
sysctl: Removed unused variable
sysctl: Nixify sysctl.sh
sysctl: Remove superfluous includes from kernel/sysctl.c
sysctl: Remove (very) old file changelog
sysctl: Move sysctl_panic_on_stackoverflow to kernel/panic.c
sysctl: move cad_pid into kernel/pid.c
sysctl: Move tainted ctl_table into kernel/panic.c
Input: sysrq: mv sysrq into drivers/tty/sysrq.c
fork: mv threads-max into kernel/fork.c
parisc/power: Move soft-power into power.c
mm: move randomize_va_space into memory.c
...
Here is the big set of TTY and Serial driver updates for 6.17-rc1.
Included in here is the following types of changes:
- another cleanup round from Jiri for the 8250 serial driver and some
other tty drivers, things are slowly getting better with our apis
thanks to this work. This touched many tty drivers all over the
tree.
- qcom_geni_serial driver update for new platforms and devices
- 8250 quirk handling fixups
- dt serial binding updates for different boards/platforms
- other minor cleanups and fixes
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCaIeWPw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymQHgCfR3KXFe7ElzXQqjJhtN/ej6IPijIAoI6k3g0m
4UewNOIef9XpIAJ8zuoo
=850o
-----END PGP SIGNATURE-----
Merge tag 'tty-6.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver updates from Greg KH:
"Here is the big set of TTY and Serial driver updates for 6.17-rc1.
Included in here is the following types of changes:
- another cleanup round from Jiri for the 8250 serial driver and some
other tty drivers, things are slowly getting better with our apis
thanks to this work. This touched many tty drivers all over the
tree.
- qcom_geni_serial driver update for new platforms and devices
- 8250 quirk handling fixups
- dt serial binding updates for different boards/platforms
- other minor cleanups and fixes
All of these have been in linux-next with no reported issues"
* tag 'tty-6.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (79 commits)
dt-bindings: serial: snps-dw-apb-uart: Allow use of a power-domain
serial: 8250: fix panic due to PSLVERR
dt-bindings: serial: samsung: add samsung,exynos2200-uart compatible
vt: defkeymap: Map keycodes above 127 to K_HOLE
vt: keyboard: Don't process Unicode characters in K_OFF mode
serial: qcom-geni: Enable Serial on SA8255p Qualcomm platforms
serial: qcom-geni: Enable PM runtime for serial driver
serial: qcom-geni: move clock-rate logic to separate function
serial: qcom-geni: move resource control logic to separate functions
serial: qcom-geni: move resource initialization to separate function
soc: qcom: geni-se: Enable QUPs on SA8255p Qualcomm platforms
dt-bindings: qcom: geni-se: describe SA8255p
dt-bindings: serial: describe SA8255p
serial: 8250_dw: Fix typo "notifer"
dt-bindings: serial: 8250: spacemit: set clocks property as required
dt-bindings: serial: renesas: Document RZ/V2N SCIF
serial: 8250_ce4100: Fix CONFIG_SERIAL_8250=n build
tty: omit need_resched() before cond_resched()
serial: 8250_ni: Reorder local variables
serial: 8250_ni: Fix build warning
...
- Fix two initialization ordering issues in the cpufreq core and a
governor initialization error path in it, and clean it up (Lifeng
Zheng)
- Add Granite Rapids support in no-HWP mode to the intel_pstate cpufreq
driver (Li RongQing)
- Make intel_pstate always use HWP_DESIRED_PERF when operating in the
passive mode (Rafael Wysocki)
- Allow building the tegra124 cpufreq driver as a module (Aaron Kling)
- Do minor cleanups for Rust cpufreq and cpumask APIs and fix MAINTAINERS
entry for cpu.rs (Abhinav Ananthu, Ritvik Gupta, Lukas Bulwahn)
- Clean up assorted cpufreq drivers (Arnd Bergmann, Dan Carpenter,
Krzysztof Kozlowski, Sven Peter, Svyatoslav Ryhel, Lifeng Zheng)
- Add the NEED_UPDATE_LIMITS flag to the CPPC cpufreq driver (Prashant
Malani)
- Fix minimum performance state label error in the amd-pstate driver
documentation (Shouye Liu)
- Add the CPUFREQ_GOV_STRICT_TARGET flag to the userspace cpufreq
governor and explain HW coordination influence on it in the
documentation (Shashank Balaji)
- Fix opencoded for_each_cpu() in idle_state_valid() in the DT cpuidle
driver (Yury Norov)
- Remove info about non-existing QoS interfaces from the PM QoS
documentation (Ulf Hansson)
- Use c_* types via kernel prelude in Rust for OPP (Abhinav Ananthu)
- Add HiSilicon uncore frequency scaling driver to devfreq (Jie Zhan)
- Allow devfreq drivers to add custom sysfs ABIs (Jie Zhan)
- Simplify the sun8i-a33-mbus devfreq driver by using more devm
functions (Uwe Kleine-König)
- Fix an index typo in trans_stat() in devfreq (Chanwoo Choi)
- Check devfreq governor before using governor->name (Lifeng Zheng)
- Remove a redundant devfreq_get_freq_range() call from
devfreq_add_device() (Lifeng Zheng)
- Limit max_freq with scaling_min_freq in devfreq (Lifeng Zheng)
- Replace sscanf() with kstrtoul() in set_freq_store() (Lifeng Zheng)
- Extend the asynchronous suspend and resume of devices to handle
suppliers like parents and consumers like children (Rafael Wysocki)
- Make pm_runtime_force_resume() work for drivers that set the
DPM_FLAG_SMART_SUSPEND flag and allow PCI drivers and drivers that
collaborate with the general ACPI PM domain to set it (Rafael
Wysocki)
- Add kernel parameter to disable asynchronous suspend/resume of
devices (Tudor Ambarus)
- Drop redundant might_sleep() calls from some functions in the device
suspend/resume core code (Zhongqiu Han)
- Fix the handling of monitors connected right before waking up the
system from sleep (tuhaowen)
- Clean up MAINTAINERS entries for suspend and hibernation (Rafael
Wysocki)
- Fix error code path in the KEXEC_JUMP flow and drop a redundant
pm_restore_gfp_mask() call from it (Rafael Wysocki)
- Rearrange suspend/resume error handling in the core device suspend
and resume code (Rafael Wysocki)
- Fix up white space that does not follow coding style in the
hibernation core code (Darshan Rathod)
- Document return values of suspend-related API functions in the
runtime PM framework (Sakari Ailus)
- Mark last busy stamp in multiple autosuspend-related functions in the
runtime PM framework and update its documentation (Sakari Ailus)
- Take active children into account in pm_runtime_get_if_in_use() for
consistency (Rafael Wysocki)
- Fix NULL pointer dereference in get_pd_power_uw() in the dtpm_cpu
power capping driver (Sivan Zohar-Kotzer)
- Add support for the Bartlett Lake platform to the Intel RAPL power
capping driver (Qiao Wei)
- Add PL4 support for Panther Lake to the intel_rapl_msr power capping
driver (Zhang Rui)
- Update contact information in the PM ABI docs and maintainer
information in the power domains DT binding (Rafael Wysocki)
- Update PM header inclusions to follow the IWYU (Include What You Use)
principle (Andy Shevchenko)
- Add flags to specify power on attach/detach for PM domains, make the
driver core detach PM domains in device_unbind_cleanup(), and drop
the dev_pm_domain_detach() call from the platform bus type (Claudiu
Beznea)
- Improve Python binding's Makefile for cpupower (John B. Wyatt IV)
- Fix printing of CORE, CPU fields in cpupower-monitor (Gautham Shenoy)
-----BEGIN PGP SIGNATURE-----
iQFGBAABCAAwFiEEcM8Aw/RY0dgsiRUR7l+9nS/U47UFAmh/wC4SHHJqd0Byand5
c29ja2kubmV0AAoJEO5fvZ0v1OO1O6MIAJtfclAleksv+PzbEyC+yk72zKinJg35
WJUk4Kz1yMOqAPazbpXRXt1tuxqyB3HWeixnTFyZbz+bbhZjYJ0lvpWGkdsFaS0i
NSbILSpHNGtOrP6s6hVKTBmLAdAzdWYWMQizlWgGrkhOiN5BnQzL7pAi2aGqu9KS
tGqnIg/3QwBAvnxijgpkm7qozOUMPJ9dzSvxMaFeB6JH7SNbTOODVFtsoD+mbJlH
YVMMWxih8b4MRJgAo4N2bL1Glp/Qnwg4ACawnQokt8Rknbtwku57QF9YwTbubr36
Ok7qbNnUSx0h9KtMQQNogLLkFreTJkbGknVWEwaWWhXNeW9l4cr6MWo=
=xVF9
-----END PGP SIGNATURE-----
Merge tag 'pm-6.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"As is tradition, cpufreq is the part with the largest number of
updates that include core fixes and cleanups as well as updates of
several assorted drivers, but there are also quite a few updates
related to system sleep, mostly focused on asynchronous suspend and
resume of devices and on making the integration of system suspend
and resume with runtime PM easier.
Runtime PM is also updated to allow some code duplication in drivers
to be eliminated going forward and to work more consistently overall
in some cases.
Apart from that, there are some driver core updates related to PM
domains that should help to address ordering issues with devm_ cleanup
routines relying on PM domains, some assorted devfreq updates
including core fixes and cleanups, tooling updates, and documentation
and MAINTAINERS updates.
Specifics:
- Fix two initialization ordering issues in the cpufreq core and a
governor initialization error path in it, and clean it up (Lifeng
Zheng)
- Add Granite Rapids support in no-HWP mode to the intel_pstate
cpufreq driver (Li RongQing)
- Make intel_pstate always use HWP_DESIRED_PERF when operating in the
passive mode (Rafael Wysocki)
- Allow building the tegra124 cpufreq driver as a module (Aaron
Kling)
- Do minor cleanups for Rust cpufreq and cpumask APIs and fix
MAINTAINERS entry for cpu.rs (Abhinav Ananthu, Ritvik Gupta, Lukas
Bulwahn)
- Clean up assorted cpufreq drivers (Arnd Bergmann, Dan Carpenter,
Krzysztof Kozlowski, Sven Peter, Svyatoslav Ryhel, Lifeng Zheng)
- Add the NEED_UPDATE_LIMITS flag to the CPPC cpufreq driver
(Prashant Malani)
- Fix minimum performance state label error in the amd-pstate driver
documentation (Shouye Liu)
- Add the CPUFREQ_GOV_STRICT_TARGET flag to the userspace cpufreq
governor and explain HW coordination influence on it in the
documentation (Shashank Balaji)
- Fix opencoded for_each_cpu() in idle_state_valid() in the DT
cpuidle driver (Yury Norov)
- Remove info about non-existing QoS interfaces from the PM QoS
documentation (Ulf Hansson)
- Use c_* types via kernel prelude in Rust for OPP (Abhinav Ananthu)
- Add HiSilicon uncore frequency scaling driver to devfreq (Jie Zhan)
- Allow devfreq drivers to add custom sysfs ABIs (Jie Zhan)
- Simplify the sun8i-a33-mbus devfreq driver by using more devm
functions (Uwe Kleine-König)
- Fix an index typo in trans_stat() in devfreq (Chanwoo Choi)
- Check devfreq governor before using governor->name (Lifeng Zheng)
- Remove a redundant devfreq_get_freq_range() call from
devfreq_add_device() (Lifeng Zheng)
- Limit max_freq with scaling_min_freq in devfreq (Lifeng Zheng)
- Replace sscanf() with kstrtoul() in set_freq_store() (Lifeng Zheng)
- Extend the asynchronous suspend and resume of devices to handle
suppliers like parents and consumers like children (Rafael Wysocki)
- Make pm_runtime_force_resume() work for drivers that set the
DPM_FLAG_SMART_SUSPEND flag and allow PCI drivers and drivers that
collaborate with the general ACPI PM domain to set it (Rafael
Wysocki)
- Add kernel parameter to disable asynchronous suspend/resume of
devices (Tudor Ambarus)
- Drop redundant might_sleep() calls from some functions in the
device suspend/resume core code (Zhongqiu Han)
- Fix the handling of monitors connected right before waking up the
system from sleep (tuhaowen)
- Clean up MAINTAINERS entries for suspend and hibernation (Rafael
Wysocki)
- Fix error code path in the KEXEC_JUMP flow and drop a redundant
pm_restore_gfp_mask() call from it (Rafael Wysocki)
- Rearrange suspend/resume error handling in the core device suspend
and resume code (Rafael Wysocki)
- Fix up white space that does not follow coding style in the
hibernation core code (Darshan Rathod)
- Document return values of suspend-related API functions in the
runtime PM framework (Sakari Ailus)
- Mark last busy stamp in multiple autosuspend-related functions in
the runtime PM framework and update its documentation (Sakari
Ailus)
- Take active children into account in pm_runtime_get_if_in_use() for
consistency (Rafael Wysocki)
- Fix NULL pointer dereference in get_pd_power_uw() in the dtpm_cpu
power capping driver (Sivan Zohar-Kotzer)
- Add support for the Bartlett Lake platform to the Intel RAPL power
capping driver (Qiao Wei)
- Add PL4 support for Panther Lake to the intel_rapl_msr power
capping driver (Zhang Rui)
- Update contact information in the PM ABI docs and maintainer
information in the power domains DT binding (Rafael Wysocki)
- Update PM header inclusions to follow the IWYU (Include What You
Use) principle (Andy Shevchenko)
- Add flags to specify power on attach/detach for PM domains, make
the driver core detach PM domains in device_unbind_cleanup(), and
drop the dev_pm_domain_detach() call from the platform bus type
(Claudiu Beznea)
- Improve Python binding's Makefile for cpupower (John B. Wyatt IV)
- Fix printing of CORE, CPU fields in cpupower-monitor (Gautham
Shenoy)"
* tag 'pm-6.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (75 commits)
cpufreq: CPPC: Mark driver with NEED_UPDATE_LIMITS flag
PM: docs: Use my kernel.org address in ABI docs and DT bindings
PM: hibernate: Fix up white space that does not follow coding style
PM: sleep: Rearrange suspend/resume error handling in the core
Documentation: amd-pstate:fix minimum performance state label error
PM: runtime: Take active children into account in pm_runtime_get_if_in_use()
kexec_core: Drop redundant pm_restore_gfp_mask() call
kexec_core: Fix error code path in the KEXEC_JUMP flow
PM: sleep: Clean up MAINTAINERS entries for suspend and hibernation
drivers: cpufreq: add Tegra114 support
rust: cpumask: Replace `MaybeUninit` and `mem::zeroed` with `Opaque` APIs
cpufreq: Exit governor when failed to start old governor
cpufreq: Move the check of cpufreq_driver->get into cpufreq_verify_current_freq()
cpufreq: Init policy->rwsem before it may be possibly used
cpufreq: Initialize cpufreq-based frequency-invariance later
cpufreq: Remove duplicate check in __cpufreq_offline()
cpufreq: Contain scaling_cur_freq.attr in cpufreq_attrs
cpufreq: intel_pstate: Add Granite Rapids support in no-HWP mode
cpufreq: intel_pstate: Always use HWP_DESIRED_PERF in passive mode
PM / devfreq: Add HiSilicon uncore frequency scaling driver
...
I am switching my address to a personal domain, so some files in the
SGI IP30 and IOC3 files need to be updated. I will send updates for
the MAINTAINERS file and rtc-ds1685 separately to linux-rtc.
Signed-off-by: Joshua Kinard <kumba@gentoo.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
When the PSLVERR_RESP_EN parameter is set to 1, the device generates
an error response if an attempt is made to read an empty RBR (Receive
Buffer Register) while the FIFO is enabled.
In serial8250_do_startup(), calling serial_port_out(port, UART_LCR,
UART_LCR_WLEN8) triggers dw8250_check_lcr(), which invokes
dw8250_force_idle() and serial8250_clear_and_reinit_fifos(). The latter
function enables the FIFO via serial_out(p, UART_FCR, p->fcr).
Execution proceeds to the serial_port_in(port, UART_RX).
This satisfies the PSLVERR trigger condition.
When another CPU (e.g., using printk()) is accessing the UART (UART
is busy), the current CPU fails the check (value & ~UART_LCR_SPAR) ==
(lcr & ~UART_LCR_SPAR) in dw8250_check_lcr(), causing it to enter
dw8250_force_idle().
Put serial_port_out(port, UART_LCR, UART_LCR_WLEN8) under the port->lock
to fix this issue.
Panic backtrace:
[ 0.442336] Oops - unknown exception [#1]
[ 0.442343] epc : dw8250_serial_in32+0x1e/0x4a
[ 0.442351] ra : serial8250_do_startup+0x2c8/0x88e
...
[ 0.442416] console_on_rootfs+0x26/0x70
Fixes: c49436b657 ("serial: 8250_dw: Improve unwritable LCR workaround")
Link: https://lore.kernel.org/all/84cydt5peu.fsf@jogness.linutronix.de/T/
Signed-off-by: Yunhui Cui <cuiyunhui@bytedance.com>
Reviewed-by: John Ogness <john.ogness@linutronix.de>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20250723023322.464-2-cuiyunhui@bytedance.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move both sysrq ctl_table and supported sysrq_sysctl_handler helper
function into drivers/tty/sysrq.c. Replaced the __do_proc_dointvec in
helper function with do_proc_dointvec_minmax as the former is local to
kernel/sysctl.c. Here we use the minmax version of do_proc_dointvec
because do_proc_dointvec is static and calling do_proc_dointvec_minmax
with a NULL min and max is the same as calling do_proc_dointvec.
This is part of a greater effort to move ctl tables into their
respective subsystems which will reduce the merge conflicts in
kernel/sysctl.c.
Reviewed-by: Kees Cook <kees@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Joel Granados <joel.granados@kernel.org>
The maximum number of keycodes got bumped to 256 a very long time ago,
but the default keymaps were never adjusted to match. This is causing
the kernel to interpret keycodes above 127 as U+0000 if the shipped
generated keymap is used.
Fix this by mapping all keycodes above 127 to K_HOLE so the kernel
ignores them.
The contents of this patche were generated by rerunning `loadkeys
--mktable --unicode` and only including the changes to map keycodes
above 127 to K_HOLE.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Myrrh Periwinkle <myrrhperiwinkle@qtmlabs.xyz>
Cc: stable <stable@kernel.org>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250702-vt-misc-unicode-fixes-v1-2-c27e143cc2eb@qtmlabs.xyz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We don't process Unicode characters if the virtual terminal is in raw
mode, so there's no reason why we shouldn't do the same for K_OFF
(especially since people would expect K_OFF to actually turn off all VT
key processing).
Fixes: 9fc3de9c83 ("vt: Add virtual console keyboard mode OFF")
Signed-off-by: Myrrh Periwinkle <myrrhperiwinkle@qtmlabs.xyz>
Cc: stable <stable@kernel.org>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250702-vt-misc-unicode-fixes-v1-1-c27e143cc2eb@qtmlabs.xyz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Qualcomm automotive SA8255p SoC relies on firmware to configure
platform resources, including clocks, interconnects and TLMM.
The driver requests resources operations over SCMI using power
and performance protocols.
The SCMI power protocol enables or disables resources like clocks,
interconnect paths, and TLMM (GPIOs) using runtime PM framework APIs,
such as resume/suspend, to control power states(on/off).
The SCMI performance protocol manages UART baud rates, with each baud
rate represented by a performance level. The driver uses the
dev_pm_opp_set_level() API to request the desired baud rate by
specifying the performance level.
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Praveen Talari <quic_ptalari@quicinc.com>
Link: https://lore.kernel.org/r/20250721174532.14022-9-quic_ptalari@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The GENI serial driver currently handles power resource management
through calls to the statically defined geni_serial_resources_on() and
geni_serial_resources_off() functions. This approach reduces modularity
and limits support for platforms with diverse power management
mechanisms, including resource managed by firmware.
Improve modularity and enable better integration with platform-specific
power management, introduce support for runtime PM. Use
pm_runtime_resume_and_get() and pm_runtime_put_sync() within the
qcom_geni_serial_pm() callback to control resource power state
transitions based on UART power state changes.
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Praveen Talari <quic_ptalari@quicinc.com>
Link: https://lore.kernel.org/r/20250721174532.14022-8-quic_ptalari@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Facilitates future modifications within the new function,
leading to better readability and maintainability of the code.
Move the code that handles the actual logic of clock-rate
calculations to a separate function geni_serial_set_rate()
which enhances code readability.
Signed-off-by: Praveen Talari <quic_ptalari@quicinc.com>
Link: https://lore.kernel.org/r/20250721174532.14022-7-quic_ptalari@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Supports use in PM system/runtime frameworks, helping to distinguish new
resource control mechanisms and facilitate future modifications within
the new API.
The code that handles the actual enable or disable of resources like clock
and ICC paths to a separate function (geni_serial_resources_on() and
geni_serial_resources_off()) which enhances code readability.
Introduced minor return checks in newly added function APIs to enhance
error detection and prevent silent failures.
Signed-off-by: Praveen Talari <quic_ptalari@quicinc.com>
Link: https://lore.kernel.org/r/20250721174532.14022-6-quic_ptalari@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enhances code readability and future modifications within the new API.
Move the code that handles the actual initialization of resources
like clock and ICC paths to a separate function, making the
probe function cleaner.
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Praveen Talari <quic_ptalari@quicinc.com>
Link: https://lore.kernel.org/r/20250721174532.14022-5-quic_ptalari@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a spelling mistake of 'notifer' in the comment which
should be 'notifier'.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: WangYuli <wangyuli@uniontech.com>
Link: https://lore.kernel.org/r/BD4804BF4FBA1648+20250722073431.21983-6-wangyuli@uniontech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On i386, when
CONFIG_X86_INTEL_CE=y
# CONFIG_SERIAL_8250 is not set
it will try to compile the driver and use the stub simultaneously.
This breaks the build. Fix it by making sure that the driver
compiles only when CONFIG_SERIAL_8250 is also enabled.
On top of that ensure that CONFIG_SERIAL_8250 is actually set to 'y'
and not 'm' as the later makes no sense for this platform. The hook
may only be applied during early boot.
Fixes: acc902de05 ("serial: 8250: Move CE4100 quirks to a module under 8250 driver")
Fixes: 5ec6960f6f ("ce4100: Add errata fixes for UART on CE4100")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Closes: https://lore.kernel.org/r/cdf4ee46-7bf8-4379-9245-fed9db72e7e8@infradead.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20250716142412.1667927-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCgA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmh9azkeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG7GIH/0lpQtHRl6N+q2Qs
v75iG2ZouWyw2JlhUOHAToKU58MZqqTXLZzc8ZdY6fAd7DpXWKRGSDsyWVyLbUkt
UKGzXEIJsHXYvw2QIPbhkY9gQBWpdZTh4tHztFyKb0QLn81qkibVP6ChOwSzOGa/
xUyQ5v6yH+JvQlnQaCgy6hi7cMrLNSNZmuIjy0yc5Y153YPEtX5OUPO2PstpUx5r
AuiOhU4ewW9QCe07X/Pk7tdn0T2Jg8Kwk1FViaM0RBUf/0GXGfsovIxpUP/eCyMc
MA+9SXXLlDa/4Z8w3EsQYx6m2MnNmm0HPeevCmWqq3+Ocooik4si1BpzHfUaE6n/
/0D8zBg=
=NzEi
-----END PGP SIGNATURE-----
Merge tag 'v6.16-rc7' into tty-next
We need the tty/serial fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's no need to call need_resched() because cond_resched() will do
nothing if need_resched() returns false.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Link: https://lore.kernel.org/r/5a11ad09-5508-933c-f044-6a236bf00557@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert the Renesas SuperH SCI(F) serial port driver from
SIMPLE_DEV_PM_OPS() to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr().
This lets us drop the __maybe_unused annotations from its suspend and
resume callbacks, and reduces kernel size in case CONFIG_PM or
CONFIG_PM_SLEEP is disabled.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/a5628fe028362ae3f8729021a7864dd39f7869bf.1752086885.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Define a new RSCI port type, and the RSCI 32 bits registers set.
The RZ/T2H SCI has a a fifo, and a quite different set of registers
from the original SH SCI ones.
DMA is not supported yet.
Signed-off-by: Thierry Bultel <thierry.bultel.yh@bp.renesas.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20250630202323.279809-6-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
New port types cannot be added in serial_core.h, which is shared with
userspace.
In order to support new port types, the coming new ones will have
BIT(7) set in the id value, and in this case, uartport->type is
set to PORT_GENERIC.
This commit therefore changes all the places where the port type is
read, by not relying on uartport->type but on the private
value stored in struct sci_port.
Signed-off-by: Thierry Bultel <thierry.bultel.yh@bp.renesas.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20250630202323.279809-5-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace direct calls to sci_stop_rx() and sci_stop_tx() with port ops
callbacks in sci_shutdown(). This enables the RSCI driver, which reuses
the SCI core but implements its own stop_rx and stop_tx logic, to reuse
sci_shutdown() without duplicating code.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20250630202323.279809-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In one place in ce4100_mem_serial_in() the code may be replaced with
mem_serial_in() call. Do it so and collapse two conditionals into one.
Suggested-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250701134200.2621898-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dma_sync_sg_for_device() functions should be called with the same
nents as the dma_map_sg(), not the value the map function returned
according to the documentation in Documentation/core-api/dma-api.rst:450:
With the sync_sg API, all the parameters must be the same
as those passed into the sg mapping API.
Fixes: da3564ee02 ("pch_uart: add multi-scatter processing")
Cc: stable <stable@kernel.org>
Signed-off-by: Thomas Fourier <fourier.thomas@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250701113452.18590-2-fourier.thomas@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to drop the OF node reference taken when initialising the
control and port devices when the devices are later released.
Fixes: d36f0e9a00 ("serial: core: restore of_node information in sysfs")
Cc: Aidan Stewart <astewart@tektelic.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20250708085817.16070-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Calling dev_pm_domain_attach()/dev_pm_domain_detach() in bus driver
probe/remove functions can affect system behavior when the drivers
attached to the bus use devres-managed resources. Since devres actions
may need to access device registers, calling dev_pm_domain_detach() too
early, i.e., before these actions complete, can cause failures on some
systems. One such example is Renesas RZ/G3S SoC-based platforms.
If the device clocks are managed via PM domains, invoking
dev_pm_domain_detach() in the bus driver's remove function removes the
device's clocks from the PM domain, preventing any subsequent
pm_runtime_resume*() calls from enabling those clocks.
The second argument of dev_pm_domain_attach() specifies whether the PM
domain should be powered on during attachment. Likewise, the second
argument of dev_pm_domain_detach() indicates whether the domain should be
powered off during detachment.
Upcoming changes address the issue described above (initially for the
platform bus only) by deferring the call to dev_pm_domain_detach() until
after devres_release_all() in device_unbind_cleanup(). The detach_power_off
field in struct dev_pm_info stores the detach power off info from the
second argument of dev_pm_domain_attach().
Because there are cases where the device's PM domain power-on/off behavior
must be conditional (e.g., in i2c_device_probe()), the patch introduces
PD_FLAG_ATTACH_POWER_ON and PD_FLAG_DETACH_POWER_OFF flags to be passed
to dev_pm_domain_attach().
Finally, dev_pm_domain_attach() and its users are updated to use the newly
introduced PD_FLAG_ATTACH_POWER_ON and PD_FLAG_DETACH_POWER_OFF macros.
This change is preparatory.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com> # I2C
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://patch.msgid.link/20250703112708.1621607-2-claudiu.beznea.uj@bp.renesas.com
[ rjw: Changelog adjustments ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There is inconvenient for maintainers and maintainership to have
some quirks under architectural code. Move it to the specific quirk
file like other 8250-compatible drivers do.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250627182743.1273326-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'struct lpuart_soc_data' are not modified in this driver.
Constifying these structures moves some data to a read-only section, so
increases overall security.
This also makes the code more consistent.
On a x86_64, with allmodconfig, as an example:
Before:
======
text data bss dec hex filename
172668 23470 128 196266 2feaa drivers/tty/serial/fsl_lpuart.o
After:
=====
text data bss dec hex filename
172924 23214 128 196266 2feaa drivers/tty/serial/fsl_lpuart.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/93dc860a06f92236db283c71be0640cc477b7291.1751092467.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 7a637784d5 ("serial: imx: reduce RX interrupt frequency")
introduced a regression on the i.MX6UL EVK board. The issue can be
reproduced with the following steps:
- Open vi on the board.
- Paste a text file (~150 characters).
- Save the file, then repeat the process.
- Compare the sha256sum of the saved files.
The checksums do not match due to missing characters or entire lines.
Fix this by restoring the RXTL value to 1 when the UART is used as a
console.
This ensures timely RX interrupts and reliable data reception in console
mode.
With this change, pasted content is saved correctly, and checksums are
always consistent.
Cc: stable <stable@kernel.org>
Fixes: 7a637784d5 ("serial: imx: reduce RX interrupt frequency")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/20250619114617.2791939-1-festevam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The check for "port.type == PORT_8250_CIR" is present twice in
serial8250_register_8250_port(). The latter was already tried to be
dropped by 1104321a7b ("serial: Delete dead code for CIR serial
ports") and then reverted by 9527b82ae3 ("Revert "serial: Delete dead
code for CIR serial ports"").
Document this weirdness with a reason.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: "Maciej S. Szmigiero" <mail@maciej.szmigiero.name>
Link: https://lore.kernel.org/all/aFcDOx1bdB34I5hS@surfacebook.localdomain/
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20250624080641.509959-5-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are already variables like 'iir_noint1' and 'iir_noint2'. Follow
the preexisting lowercase naming of variables. So s/lsr_TEMT/lsr_temt/
and 'iir_NOINT' likewise.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Suggested-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250624080641.509959-4-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit 795158691c ("serial: 8250: extract
serial8250_initialize()"), split serial8250_initialize() even more --
the TX enable test part of this code can be separated into
serial8250_iir_txen_test().
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Suggested-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250624080641.509959-3-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit 795158691c ("serial: 8250: extract
serial8250_initialize()"), split serial8250_initialize() even more --
the mctrl part of this code can be separated into
serial8250_init_mctrl() -- done now.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Suggested-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250624080641.509959-2-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The RSA functions moved by the below commit to 8250_rsa.c are used in
8250_base.c. Since that can be a module (when CONFIG_SERIAL_8250=m),
this causes build failures:
ERROR: modpost: "rsa_autoconfig" [drivers/tty/serial/8250/8250_base.ko] undefined!
ERROR: modpost: "rsa_reset" [drivers/tty/serial/8250/8250_base.ko] undefined!
ERROR: modpost: "rsa_disable" [drivers/tty/serial/8250/8250_base.ko] undefined!
ERROR: modpost: "rsa_enable" [drivers/tty/serial/8250/8250_base.ko] undefined!
Fix them by exporting the functions. But only to the base module using
EXPORT_SYMBOL_GPL_FOR_MODULES(). (And not to the whole world.)
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://lore.kernel.org/all/20250619165607.33403e19@canb.auug.org.au/
Fixes: 5a128fb475 ("serial: 8250: move RSA functions to 8250_rsa.c")
Link: https://lore.kernel.org/r/20250623061035.436414-1-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since in v6.8-rc1, the of_node symlink under tty devices is
missing. This breaks any udev rules relying on this information.
Link the of_node information in the serial controller device with the
parent defined in the device tree. This will also apply to the serial
device which takes the serial controller as a parent device.
Fixes: b286f4e87e ("serial: core: Move tty and serdev to be children of serial core port device")
Cc: stable@vger.kernel.org
Signed-off-by: Aidan Stewart <astewart@tektelic.com>
Link: https://lore.kernel.org/r/20250617164819.13912-1-astewart@tektelic.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the correct function parameter name in ucs_get_fallback() to prevent
kernel-doc warnings:
Warning: drivers/tty/vt/ucs.c:218 function parameter 'cp' not described in 'ucs_get_fallback'
Warning: drivers/tty/vt/ucs.c:218 Excess function parameter 'base' description in 'ucs_get_fallback'
Fixes: fe26933cf1 ("vt: add ucs_get_fallback()")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Nicolas Pitre <npitre@baylibre.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: linux-serial@vger.kernel.org
Reviewed-by: Nicolas Pitre <npitre@baylibre.com>.
Link: https://lore.kernel.org/r/20250611020229.2650595-1-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Programs using poll() on /dev/vcsa to be notified when VT changes occur
were missing one case: the switch from gfx to text mode.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Link: https://lore.kernel.org/r/9o5ro928-0pp4-05rq-70p4-ro385n21n723@onlyvoer.pbz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The serial info sometimes produces negative TX/RX counts. E.g.:
3: uart:FSL_LPUART mmio:0x02970000 irq:46 tx:-1595870545 rx:339619
RTS|CTS|DTR|DSR|CD
It appears that the print format specifiers don't match with the types of
the respective variables. E.g.: All of the fields in struct uart_icount
are u32, but the format specifier used is %d, even though u32 is unsigned
and %d is for signed integers. Update drivers/tty/serial/serial_core.c
to use the proper format specifiers. Reference
https://docs.kernel.org/core-api/printk-formats.html as the documentation
for what format specifiers are the proper ones to use for a given C type.
Signed-off-by: Joseph Tilahun <jtilahun@astranis.com>
Link: https://lore.kernel.org/r/20250610065653.3750067-1-jtilahun@astranis.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable the use of the RTS pin for direction control in half-duplex modes to
prevent data collisions. Utilize the rs485 structure and callbacks in the
serial core framework to support half-duplex modes. Implement support for
the TIOCSRS485 IOCTL value and the struct serial_rs485.
Signed-off-by: Anup Kulkarni <quic_anupkulk@quicinc.com>
Link: https://lore.kernel.org/r/20250603110145.3835111-1-quic_anupkulk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current GENI UART driver supports Max Baud rate up to 4 Mbps.
Add support to increase maximum baud rate to 8 Mbps.
Signed-off-by: Jyothi Kumar Seerapu <quic_jseerapu@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250523103721.5042-1-quic_jseerapu@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are unnecessary "up->port." accesses on many places in 8250_omap.
"port" is avalable on most places, so instead simply use "port->".
And make port available in omap8250_restore_regs() too. It's used on
many places in there.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250611100319.186924-34-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of open-coding the hash table, use the one provided by
hashtable.h. The semantics is the same, except the code needs not to
compute the hash bucket on its own.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250611100319.186924-33-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no point in a long 'if' in serial8250_register_8250_port() to
just return ENOSPC for PORT_8250_CIR ports. Invert the condition and
return immediately.
'gpios' variable was moved to its set location.
And return ENODEV instead of ENOSPC. The latter is a leftover from the
previous find-uart 'if'. The former makes a lot more sense in this case.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20250611100319.186924-31-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DEBUG_AUTOCONF() is always disabled (by "#if 0"), so one would need to
recompile the kernel to use it. And even if they did, they would find
out it is broken anyway:
error: variable 'scratch' is used uninitialized whenever 'if' condition is false
Drop it.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20250611100319.186924-30-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These are useless, we have tracing nowadays.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20250611100319.186924-29-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This find-or-create-irq part of the serial_link_irq_chain()'s code is
logically bounded and self-standing. For easier-to-follow code flow,
extract the code to a separate function:
serial_get_or_create_irq_info().
This allows for an easier found-an-irq handling -- simple jump to the
'unlock' label and return. That results in one less 'if' levels.
Note when using guard()s in the upcoming patchset, the label can dropped
altogether.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20250611100319.186924-28-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'frac' is not used in the generic implementation of get_divisor. Drop it
from there. (Only some port->get_divisor() compute that and receive it
then to port->set_divisor()).
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20250611100319.186924-27-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* use 'lcr' as variable containing the "computed value" (and not 'cval')
* use 'u8' for the type (and not 'unsigned char')
* drop useless comment
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20250611100319.186924-26-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial8250_do_set_termios() consists of many registers and up flags
settings. Extract all these into separate functions. This time, setting
of FCR.
serial8250_do_set_termios() looks sane at this point.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20250611100319.186924-25-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial8250_do_set_termios() consists of many registers and up flags
settings. Extract all these into separate functions. This time, setting
of EFR for UART_CAP_EFR ports.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250611100319.186924-24-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial8250_do_set_termios() consists of many registers and up flags
settings. Extract all these into separate functions. This time, setting
of IER.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20250611100319.186924-23-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial8250_do_set_termios() consists of many registers and up flags
settings. Extract all these into separate functions. This time, setting
of ignore_status_mask and read_status_mask.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250611100319.186924-22-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial8250_do_set_termios() consists of many registers and up flags
settings. Extract all these into separate functions. This time, setting
of MCR for UART_CAP_AFE ports.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20250611100319.186924-21-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial8250_do_set_termios() consists of many registers and up flags
settings. Extract all these into separate functions. This time, setting
of trigger level for slow speeds.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20250611100319.186924-20-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial8250_do_set_termios() consists of many registers and up flags
settings. Extract all these into separate functions. This time, setting
of CSIZE for UART_CAP_MINI ports.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20250611100319.186924-19-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On three places in 8250_port.c, the interrupts are cleared by reading 4
registers. Extract this to a separate function:
serial8250_clear_interrupts(). And call it from all the places.
Note autoconfig_irq() now uses serial_port_in() instead of serial_in().
But they are the same, in fact (modulo parameter).
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20250611100319.186924-18-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial8250_do_startup() initializes the ports in the middle of the
function. This code can be separated to serial8250_initialize(), so that
serial8250_do_startup() can be readable again.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250611100319.186924-17-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial8250_do_startup() contains a stand-alone code for probing THRE.
Furthermore, the code block is conditional (port->irq and test for
UPF_NO_THRE_TEST).
Move this code to a separate function. The conditional can be evaluated
easier there -- by a simple return in the beginning. So the indentation
level lowers and the code is overall more readable now.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250611100319.186924-16-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial8250_do_startup() contains peculiar trigger levels setup for
special ports (16850, ALTR_16550_*). Move this away to a separate
function: serial8250_set_TRG_levels().
And use switch-case instead of 'if's.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20250611100319.186924-15-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Let the serial8250_do_startup() code handle the special ports (16C950,
DA830, RSA) startup in a separate function:
serial8250_startup_special().
And instead of multiple if-else-if, use switch-case. So that it can be
easily checked for PORT_RSA now too.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20250611100319.186924-14-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
They are RSA-specific, so should live in a preexisting 8250_rsa.c. Move
them there.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20250611100319.186924-13-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prefix the functions with rsa_, not suffix.
This is a preparation for moving them out to 8250_rsa.c in the next
patch.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20250611100319.186924-12-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code can short-return in case something does not hold. So invert the
conditions and return in those cases immediately. This makes the code
flow more natural and less nested.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20250611100319.186924-11-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All these:
#ifdef CONFIG_SERIAL_8250_RSA
...
#endif
in the 8250 generic code distract the reader. Introduce empty inlines to
handle the !CONFIG_SERIAL_8250_RSA case and handle the '#if's around the
RSA functions definitions.
This means rsa_autoconfig() and rsa_reset() functions were introduced to
contain the particular code.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20250611100319.186924-10-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_port::{serial_in,serial_out} (and plat_serial8250_port::* likewise)
historically use:
* 'unsigned int' for 32-bit register values in reads and writes, and
* 'int' for offsets.
Make them sane such that:
* 'u32' is used for register values, and
* 'unsigned int' is used for offsets.
While at it, name hooks' parameters, so it is clear what is what.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: Madhavan Srinivasan <maddy@linux.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250611100319.186924-9-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This code (tty_get -> vhangup -> tty_put) is repeated on few places.
Introduce a helper similar to tty_port_tty_hangup() (asynchronous) to
handle even vhangup (synchronous).
And use it on those places.
In fact, reuse the tty_port_tty_hangup()'s code and call tty_vhangup()
depending on a new bool parameter.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: David Lin <dtwlin@gmail.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Alex Elder <elder@kernel.org>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20250611100319.186924-2-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move this API to the canonical timer_*() namespace.
[ tglx: Redone against pre rc1 ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/aB2X0jCKQO56WdMt@gmail.com
Commit 1788cf6a91 ("tty: serial: switch from circ_buf to kfifo")
introduced an error in the TX DMA handling for 8250_omap.
When the OMAP_DMA_TX_KICK flag is set, the "skip_byte" is pulled from
the kfifo and emitted directly in order to start the DMA. While the
kfifo is updated, dma->tx_size is not decreased. This leads to
uart_xmit_advance() called in omap_8250_dma_tx_complete() advancing the
kfifo by one too much.
In practice, transmitting N bytes has been seen to result in the last
N-1 bytes being sent repeatedly.
This change fixes the problem by moving all of the dma setup after the
OMAP_DMA_TX_KICK handling and using kfifo_len() instead of the DMA size
for the 4-byte cutoff check. This slightly changes the behaviour at
buffer wraparound, but it still transmits the correct bytes somehow.
Now, the "skip_byte" would no longer be accounted to the stats. As
previously, dma->tx_size included also this skip byte, up->icount.tx was
updated by aforementioned uart_xmit_advance() in
omap_8250_dma_tx_complete(). Fix this by using the uart_fifo_out()
helper instead of bare kfifo_get().
Based on patch by Mans Rullgard <mans@mansr.com>
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Fixes: 1788cf6a91 ("tty: serial: switch from circ_buf to kfifo")
Link: https://lore.kernel.org/all/20250506150748.3162-1-mans@mansr.com/
Reported-by: Mans Rullgard <mans@mansr.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20250522053835.3495975-1-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The console dimension and cursor position are available through the
/dev/vcsa interface already. However the /dev/vcsa header format uses
single-byte fields therefore those values are clamped to 255.
As surprizing as this may seem, some people do use 240-column 67-row
screens (a 1920x1080 monitor with 8x16 pixel fonts) which is getting
close to the limit. Monitors with higher resolution are not uncommon
these days (3840x2160 producing a 480x135 character display) and it is
just a matter of time before someone with, say, a braille display using
the Linux VT console and BRLTTY on such a screen reports a bug about
missing and oddly misaligned screen content.
Let's add VT_GETCONSIZECSRPOS for the retrieval of console size and cursor
position without byte-sized limitations. The actual console size limit as
encoded in vt.c is 32767x32767 so using a short here is appropriate. Then
this can be used to get the cursor position when /dev/vcsa reports 255.
The screen dimension may already be obtained using TIOCGWINSZ and adding
the same information to VT_GETCONSIZECSRPOS might be redundant. However
applications that care about cursor position also care about display
size and having 2 separate system calls to obtain them separately is
wasteful. Also, the cursor position can be queried by writing "\e[6n" to
a tty and reading back the result but that may be done only by the actual
application using that tty and not a sideline observer.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Link: https://lore.kernel.org/r/20250520171851.1219676-3-nico@fluxnic.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is comprised of 3 aspects:
- Take note of when applications advertise bracketed paste support via
"\e[?2004h" and "\e[?2004l".
- Insert bracketed paste markers ("\e[200~" and "\e[201~") around pasted
content in paste_selection() when bracketed paste is active.
- Add TIOCL_GETBRACKETEDPASTE to return bracketed paste status so user
space daemons implementing cut-and-paste functionality (e.g. gpm,
BRLTTY) may know when to insert bracketed paste markers.
Link: https://en.wikipedia.org/wiki/Bracketed-paste
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250520171851.1219676-2-nico@fluxnic.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
They are listed amon those cmd values that "treat 'arg' as an integer"
which is wrong. They should instead fall into the default case. Probably
nobody ever relied on that code since 2009 but still.
Fixes: e92166517e ("tty: handle VT specific compat ioctls in vt driver")
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/pr214s15-36r8-6732-2pop-159nq85o48r7@syhkavp.arg
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The generated table maps complex characters to their simpler fallback
forms for a terminal display when corresponding glyphs are unavailable.
A page-based approach is used to reduce compiled binary footprint.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Link: https://lore.kernel.org/r/20250507141535.40655-6-nico@fluxnic.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The generated table maps complex characters to their simpler fallback
forms for a terminal display when corresponding glyphs are unavailable.
This includes diacritics, symbols as well as many drawing characters.
Fallback characters aren't perfect replacements, obviously. But they are
still far more useful than a bunch of squared question marks.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250507141535.40655-5-nico@fluxnic.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
And to do so we ensure the Unicode screen buffer is initialized when
double-width characters are encountered.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Link: https://lore.kernel.org/r/20250507141535.40655-3-nico@fluxnic.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The in_range() helper accepts a start and a length, not a start and
an end.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250507141535.40655-2-nico@fluxnic.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor parity calculations to use the standard parity8() helper.
This change eliminates redundant implementations.
Co-developed-by: Yu-Chun Lin <eleanor15x@gmail.com>
Signed-off-by: Yu-Chun Lin <eleanor15x@gmail.com>
Signed-off-by: Kuan-Wei Chiu <visitorckw@gmail.com>
Link: https://lore.kernel.org/r/20250515081311.775559-1-visitorckw@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add new dynamically generated headers to the local .gitignore.
Fixes: c2d2c5c0d6 ("vt: move UCS tables to the "shipped" form")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Nicolas Pitre <npitre@baylibre.com>
Link: https://lore.kernel.org/r/20250430122917.72105-1-brgl@bgdev.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refine several dev_err() and dev_dbg() messages to solve:
// hardcoded device name
dev_dbg(dev, "...dev_name_str...")
// repeated device name since dev_dbg() also prints it as prefix
dev_err(dev, "...%s...", dev_name(dev))
// not concise as dev_err(dev, "...%d...", err)
dev_err(dev, "...%pe...", ERR_PTR(err))
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250425-fix_serdev-v3-1-2e4ea8261640@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Systems that issue PCIe hot reset requests during a suspend/resume
cycle cause PCI1XXXX device revisions prior to C0 to get its UART
configuration registers reset to hardware default values. This results
in device inaccessibility and data transfer failures. Starting with
Revision C0, support was added in the device hardware (via the Hot
Reset Disable Bit) to allow resetting only the PCIe interface and its
associated logic, but preserving the UART configuration during a hot
reset. This patch enables the hot reset disable feature during suspend/
resume for C0 and later revisions of the device.
Signed-off-by: Rengarajan S <rengarajan.s@microchip.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250425145500.29036-1-rengarajan.s@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ExynosAutov920 SoC supports 18 UART ports, update
the value of UART_NR to accommodate the same.
Signed-off-by: Faraz Ata <faraz.ata@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250429102941.4138463-1-faraz.ata@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCgA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmgOrWseHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGFyIH/AhXcuA8y8rk43mo
t+0GO7JR4dnr4DIl74GgDjCXlXiKCT7EXMfD/ABdofTxV4Pbyv+pUODlg1E6eO9U
C1WWM5PPNBGDDEVSQ3Yu756nr0UoiFhvW0R6pVdou5cezCWAtIF9LTN8DEUgis0u
EUJD9+/cHAMzfkZwabjm/HNsa1SXv2X47MzYv/PdHKr0htEPcNHF4gqBrBRdACGy
FJtaCKhuPf6TcDNXOFi5IEWMXrugReRQmOvrXqVYGa7rfUFkZgsAzRY6n/rUN5Z9
FAgle4Vlv9ohVYj9bXX8b6wWgqiKRpoN+t0PpRd6G6ict1AFBobNGo8LH3tYIKqZ
b/dCGNg=
=xDGd
-----END PGP SIGNATURE-----
Merge 6.15-rc4 into tty-next
We need the tty/serial fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the "shipped" mechanism to copy pre-generated tables to the build
tree by default. If GENERATE_UCS_TABLES=1 then they are generated at
build time instead. If GENERATE_UCS_TABLES=2 then
gen_ucs_recompose_table.py is invoked with --full.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Suggested-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250417184849.475581-15-nico@fluxnic.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Width tables are now split into BMP (16-bit) and non-BMP (above 16-bit).
This reduces the corresponding text size by 20-25%.
Note: scripts/checkpatch.pl complains about "... exceeds 100 columns".
Please ignore.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250417184849.475581-14-nico@fluxnic.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Split table ranges into BMP (16-bit) and non-BMP (above 16-bit).
This reduces the corresponding text size by 20-25%.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250417184849.475581-13-nico@fluxnic.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is now taken care of by ucs_is_zero_width().
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250417184849.475581-12-nico@fluxnic.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the Unicode screen buffer, we follow double-width code points with a
space to maintain proper column alignment. This, however, creates
semantic problems when e.g. using cut and paste.
Let's use a better code point for the column padding's purpose i.e. a
zero-width space rather than a full space. This way the combination
retains a width of 2.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250417184849.475581-11-nico@fluxnic.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Try replacing any decomposed Unicode sequence by the corresponding
recomposed code point. Code point to glyph correspondance works best
after recomposition, and this apply mostly to single-width code points
therefore we can't preserve them in their decomposed form anyway.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250417184849.475581-10-nico@fluxnic.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Table of base character + combining mark pairs with their precomposed
equivalents.
Note: scripts/checkpatch.pl complains about "... exceeds 100 columns".
Please ignore.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250417184849.475581-9-nico@fluxnic.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The generated table maps base character + combining mark pairs to their
precomposed equivalents using Python's unicodedata module.
The default script behavior is to create a table with most commonly used
Latin, Greek, and Cyrillic recomposition pairs only. It is much smaller
than the table with all possible recomposition pairs (71 entries vs 1000
entries). But if one needs/wants the full table then simply running the
script with the --full argument will generate it.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250417184849.475581-8-nico@fluxnic.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This removes the table from ucs.c and substitutes the generated tables
from ucs_width_table.h providing comprehensive ranges for double-width
and zero-width Unicode code points.
Also implements ucs_is_zero_width() to query the new zero-width table.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250417184849.475581-7-nico@fluxnic.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The table in ucs.c is terribly out of date and incomplete. We also need a
second table to store zero-width code points. Properly maintaining those
tables manually is impossible. So here's a script to generate them.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250417184849.475581-5-nico@fluxnic.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Zero-width Unicode code points are causing misalignment in vertically
aligned content, disrupting the visual layout. Let's handle zero-width
code points more intelligently.
Double-width code points are stored in the screen grid followed by a white
space code point to create the expected screen layout. When a double-width
code point is followed by a zero-width code point in the console incoming
bytestream (e.g., an emoji with a presentation selector) then we may
replace the white space padding by that zero-width code point instead of
dropping it. This maximize screen content information while preserving
proper layout.
If a zero-width code point is preceded by a single-width code point then
the above trick is not possible and such zero-width code point must
be dropped.
VS16 (Variation Selector 16, U+FE0F) is special as it typically doubles
the width of the preceding single-width code point. We handle that case
by giving VS16 a width of 1 instead of 0 when that happens.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250417184849.475581-4-nico@fluxnic.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This will make it easier to maintain. Also make it depend on
CONFIG_CONSOLE_TRANSLATIONS.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250417184849.475581-3-nico@fluxnic.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make it clearer when a sequence is bad.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250417184849.475581-2-nico@fluxnic.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 74045f6658.
A new version of the series was submitted, so it's easier to revert the
old one and add the new one due to the changes invovled.
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 2acaf27cd7.
A new version of the series was submitted, so it's easier to revert the
old one and add the new one due to the changes invovled.
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit e88391f730.
A new version of the series was submitted, so it's easier to revert the
old one and add the new one due to the changes invovled.
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 26c94eb484.
A new version of the series was submitted, so it's easier to revert the
old one and add the new one due to the changes invovled.
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 3a1ab63aa0.
A new version of the series was submitted, so it's easier to revert the
old one and add the new one due to the changes invovled.
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit f2347b0cdf.
A new version of the series was submitted, so it's easier to revert the
old one and add the new one due to the changes invovled.
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 54af55b990.
A new version of the series was submitted, so it's easier to revert the
old one and add the new one due to the changes invovled.
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit cd6937d42b.
A new version of the series was submitted, so it's easier to revert the
old one and add the new one due to the changes invovled.
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 119ff0b0f4.
A new version of the series was submitted, so it's easier to revert the
old one and add the new one due to the changes invovled.
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit c7cb5b0779.
A new version of the series was submitted, so it's easier to revert the
old one and add the new one due to the changes invovled.
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 547f57b88d.
A new version of the series was submitted, so it's easier to revert the
old one and add the new one due to the changes invovled.
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit b35f7a773c.
A new version of the series was submitted, so it's easier to revert the
old one and add the new one due to the changes invovled.
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 8bfabff0bf.
A new version of the series was submitted, so it's easier to revert the
old one and add the new one due to the changes invovled.
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we putting character to the tty, we take into account the keyboard
mode to properly handle utf8. This code is duplicated few times.
Signed-off-by: Alexey Gladkov <legion@kernel.org>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/c0d10193e61f977b518862d8f216bbaf234138fd.1740141518.git.legion@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 8700a7ea55 (serial: 8250_omap: Drop
pm_runtime_irq_safe()), all the serial8250_rpm_*() functions are used
solely in 8250_port.
Unexport them.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250425111315.1036184-7-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_get_icount() and uart_carrier_raised() open code
uart_port_ref_lock(). Use the helper instead.
The difference is we use _irqsave() variants of a spinlock now. But
that's "safer" than _irq().
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250425111315.1036184-6-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_port_lock() and uart_port_unlock() are (at the same time) defined
as:
* functions in include/linux/serial_core.h
* macros in drivers/tty/serial/serial_core.c
The former are sane uart port lock wrappers.
The latter _lock() does something completely different: it inspects
a uart_state, obtains a uart_port from it, and increases its reference
count. And if that all succeeded, the port is locked too.
Similarly, the _unlock() counterpart first unlocks and then decrements
the refcount too.
This state is REALLY CONFUSING.
So rename the latter (local .c macros):
* uart_port_lock() -> uart_port_ref_lock(), and
* uart_port_unlock() -> uart_port_unlock_deref().
Now, the forbidden while-at-it part: convert from a macro to an inline
-- do it here as the passed 'flags' have to be pointer to ulong now. So
we avoid doubled changes on identical LOCs.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250425111315.1036184-5-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The inline-defined constants look weird. Instead, define a proper enum
for them and type uart_port::iotype as that enum. This allows for proper
checking in switch-case labels (somewhere, a default or UPIO_UNKNOWN
label needs to be added/handled).
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250425111315.1036184-4-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
guard()s and scoped_guard()s express more clearly what is protected by
locks. And also makes the code cleaner as it can return immediately in
case of short returns.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250425111315.1036184-3-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty_throttle_safe() and tty_unthrottle_safe can be made less convoluted
using guard()s. Switch them.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250425111315.1036184-2-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove API tty_port_register_device_serdev() which has no caller.
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250423-remove_api-v1-1-fac673d09feb@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mxser enables its PCI device with pcim_enable_device(). This,
implicitly, switches the function pci_request_region() into managed
mode, where it becomes a devres function.
The PCI subsystem wants to remove this hybrid nature from its
interfaces. To do so, users of the aforementioned combination of
functions must be ported to non-hybrid functions.
Replace the call to sometimes-managed pci_request_region() with one to
the always-managed pcim_request_region().
Signed-off-by: Philipp Stanner <phasta@kernel.org>
Link: https://lore.kernel.org/r/20250417081333.20917-2-phasta@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
startup()/shutdown() callbacks access SIFIVE_SERIAL_IE_OFFS.
The register is also accessed from write() callback.
If console were printing and startup()/shutdown() callback
gets called, its access to the register could be overwritten.
Add port->lock to startup()/shutdown() callbacks to make sure
their access to SIFIVE_SERIAL_IE_OFFS is synchronized against
write() callback.
Fixes: 45c054d081 ("tty: serial: add driver for the SiFive UART")
Signed-off-by: Ryo Takakura <ryotkkr98@gmail.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Cc: stable@vger.kernel.org
Reviewed-by: John Ogness <john.ogness@linutronix.de>
Rule: add
Link: https://lore.kernel.org/stable/20250330003522.386632-1-ryotkkr98%40gmail.com
Link: https://lore.kernel.org/r/20250412001847.183221-1-ryotkkr98@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Save the bus clock pointer in the of_serial_info structure, and use
that to disable the bus clock on suspend and re-enable it on resume.
Signed-off-by: Alex Elder <elder@riscstar.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Reviewed-by: Yixun Lan <dlan@gentoo.org>
Link: https://lore.kernel.org/r/20250411203828.1491595-4-elder@riscstar.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the necessary callbacks(write_atomic, write_thread, device_lock
and device_unlock) and CON_NBCON flag to switch the sifive console
driver to perform as nbcon console.
Both ->write_atomic() and ->write_thread() will check for console
ownership whenever they are accessing registers.
The ->device_lock()/unlock() will provide the additional serilization
necessary for ->write_thread() which is called from dedicated printing
thread.
Signed-off-by: Ryo Takakura <ryotkkr98@gmail.com>
Reviewed-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20250412002544.185038-1-ryotkkr98@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This requirement was overeagerly loosened in commit 2f83e38a09
("tty: Permit some TIOCL_SETSEL modes without CAP_SYS_ADMIN"), but as
it turns out,
(1) the logic I implemented there was inconsistent (apologies!),
(2) TIOCL_SELMOUSEREPORT might actually be a small security risk
after all, and
(3) TIOCL_SELMOUSEREPORT is only meant to be used by the mouse
daemon (GPM or Consolation), which runs as CAP_SYS_ADMIN
already.
In more detail:
1. The previous patch has inconsistent logic:
In commit 2f83e38a09 ("tty: Permit some TIOCL_SETSEL modes
without CAP_SYS_ADMIN"), we checked for sel_mode ==
TIOCL_SELMOUSEREPORT, but overlooked that the lower four bits of
this "mode" parameter were actually used as an additional way to
pass an argument. So the patch did actually still require
CAP_SYS_ADMIN, if any of the mouse button bits are set, but did not
require it if none of the mouse buttons bits are set.
This logic is inconsistent and was not intentional. We should have
the same policies for using TIOCL_SELMOUSEREPORT independent of the
value of the "hidden" mouse button argument.
I sent a separate documentation patch to the man page list with
more details on TIOCL_SELMOUSEREPORT:
https://lore.kernel.org/all/20250223091342.35523-2-gnoack3000@gmail.com/
2. TIOCL_SELMOUSEREPORT is indeed a potential security risk which can
let an attacker simulate "keyboard" input to command line
applications on the same terminal, like TIOCSTI and some other
TIOCLINUX "selection mode" IOCTLs.
By enabling mouse reporting on a terminal and then injecting mouse
reports through TIOCL_SELMOUSEREPORT, an attacker can simulate
mouse movements on the same terminal, similar to the TIOCSTI
keystroke injection attacks that were previously possible with
TIOCSTI and other TIOCL_SETSEL selection modes.
Many programs (including libreadline/bash) are then prone to
misinterpret these mouse reports as normal keyboard input because
they do not expect input in the X11 mouse protocol form. The
attacker does not have complete control over the escape sequence,
but they can at least control the values of two consecutive bytes
in the binary mouse reporting escape sequence.
I went into more detail on that in the discussion at
https://lore.kernel.org/all/20250221.0a947528d8f3@gnoack.org/
It is not equally trivial to simulate arbitrary keystrokes as it
was with TIOCSTI (commit 83efeeeb3d ("tty: Allow TIOCSTI to be
disabled")), but the general mechanism is there, and together with
the small number of existing legit use cases (see below), it would
be better to revert back to requiring CAP_SYS_ADMIN for
TIOCL_SELMOUSEREPORT, as it was already the case before
commit 2f83e38a09 ("tty: Permit some TIOCL_SETSEL modes without
CAP_SYS_ADMIN").
3. TIOCL_SELMOUSEREPORT is only used by the mouse daemons (GPM or
Consolation), and they are the only legit use case:
To quote console_codes(4):
The mouse tracking facility is intended to return
xterm(1)-compatible mouse status reports. Because the console
driver has no way to know the device or type of the mouse, these
reports are returned in the console input stream only when the
virtual terminal driver receives a mouse update ioctl. These
ioctls must be generated by a mouse-aware user-mode application
such as the gpm(8) daemon.
Jared Finder has also confirmed in
https://lore.kernel.org/all/491f3df9de6593df8e70dbe77614b026@finder.org/
that Emacs does not call TIOCL_SELMOUSEREPORT directly, and it
would be difficult to find good reasons for doing that, given that
it would interfere with the reports that GPM is sending.
More information on the interaction between GPM, terminals and the
kernel with additional pointers is also available in this patch:
https://lore.kernel.org/all/a773e48920aa104a65073671effbdee665c105fc.1603963593.git.tammo.block@gmail.com/
For background on who else uses TIOCL_SELMOUSEREPORT: Debian Code
search finds one page of results, the only two known callers are
the two mouse daemons GPM and Consolation. (GPM does not show up
in the search results because it uses literal numbers to refer to
TIOCLINUX-related enums. I looked through GPM by hand instead.
TIOCL_SELMOUSEREPORT is also not used from libgpm.)
https://codesearch.debian.net/search?q=TIOCL_SELMOUSEREPORT
Cc: Jared Finder <jared@finder.org>
Cc: Jann Horn <jannh@google.com>
Cc: Hanno Böck <hanno@hboeck.de>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Kees Cook <kees@kernel.org>
Cc: stable <stable@kernel.org>
Fixes: 2f83e38a09 ("tty: Permit some TIOCL_SETSEL modes without CAP_SYS_ADMIN")
Signed-off-by: Günther Noack <gnoack3000@gmail.com>
Link: https://lore.kernel.org/r/20250411070144.3959-2-gnoack3000@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MSM UART DM controller supports different working modes, e.g. DMA or
the "single-character mode", where all reads/writes operate on a single
character rather than 4 chars (32-bit) at once. When using earlycon,
__msm_console_write() always writes 4 characters at a time, but we don't
know which mode the bootloader was using and we don't set the mode either.
This causes garbled output if the bootloader was using the single-character
mode, because only every 4th character appears in the serial console, e.g.
"[ 00oni pi 000xf0[ 00i s 5rm9(l)l s 1 1 SPMTA 7:C 5[ 00A ade k d[
00ano:ameoi .Q1B[ 00ac _idaM00080oo'"
If the bootloader was using the DMA ("DM") mode, output would likely fail
entirely. Later, when the full serial driver probes, the port is
re-initialized and output works as expected.
Fix this also for earlycon by clearing the DMEN register and
reset+re-enable the transmitter to apply the change. This ensures the
transmitter is in the expected state before writing any output.
Cc: stable <stable@kernel.org>
Fixes: 0efe729634 ("tty: serial: msm: Add earlycon support")
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250408-msm-serial-earlycon-v1-1-429080127530@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The aim here is to provide an easier support to more different SCI
controllers, like the RZ/T2H one.
The existing .data field of_sci_match is changed to a structure containing
all what that can be statically initialized, and avoid a call to
'sci_probe_regmap', in both 'sci_init_single', and 'early_console_setup'.
'sci_probe_regmap' is now assumed to be called in the only case where the
device description is from a board file instead of a dts.
In this way, there is no need to patch 'sci_probe_regmap' for adding new
SCI type, and also, the specific sci_port_params for a new SCI type can be
provided by an external file.
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Thierry Bultel <thierry.bultel.yh@bp.renesas.com>
Link: https://lore.kernel.org/r/20250403212919.1137670-10-thierry.bultel.yh@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The aim here is to prepare support for new sci controllers like
the T2H/RSCI whose registers are too much different for being
handled in common code.
This named serial controller also has 32 bits register,
so some return types had to be changed.
The needed generic functions are no longer static, with prototypes
defined in sh-sci-common.h so that they can be used from specific
implementation in a separate file, to keep this driver as little
changed as possible.
For doing so, a set of 'ops' is added to struct sci_port.
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Thierry Bultel <thierry.bultel.yh@bp.renesas.com>
Link: https://lore.kernel.org/r/20250403212919.1137670-9-thierry.bultel.yh@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The comment was correct when it was added, at that time RZ/T1 was
the only SoC in the RZ/T line. Since then, further SoCs have been
added with RZ/T names which do not use the same SCIFA register
layout and so the comment is now misleading.
So we update the comment to explicitly reference only RZ/T1 SoCs.
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Thierry Bultel <thierry.bultel.yh@bp.renesas.com>
Link: https://lore.kernel.org/r/20250403212919.1137670-8-thierry.bultel.yh@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is now taken care of by ucs_is_zero_width(). And in the case where
we do want a padding from some zero-width code point then we should also
give the legacy displays a space character to work with.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Link: https://lore.kernel.org/r/6o2ss437-6nps-s943-1n38-54np5587r08s@syhkavp.arg
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the Unicode screen buffer, we follow double-width code points with a
space to maintain proper column alignment. This, however, creates
semantic problems when e.g. using cut and paste or selection.
Let's use a better code point for the column padding's purpose i.e. a
zero-white-space rather than a full space.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Link: https://lore.kernel.org/r/20250410011839.64418-12-nico@fluxnic.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Split table ranges into BMP (16-bit) and non-BMP (above 16-bit).
This reduces the corresponding text size by 20-25%.
Note: scripts/checkpatch.pl complains about "... exceeds 100 columns".
Please ignore.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Link: https://lore.kernel.org/r/20250410011839.64418-11-nico@fluxnic.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Split table ranges into BMP (16-bit) and non-BMP (above 16-bit).
This reduces the corresponding text size by 20-25%.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Link: https://lore.kernel.org/r/20250410011839.64418-10-nico@fluxnic.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Try replacing any decomposed Unicode sequence by the corresponding
recomposed code point. Code point to glyph correspondance works best
after recomposition, and this apply mostly to single-width code points
therefore we can't preserve them in their decomposed form anyway.
With all the infrastructure in place this is now trivial to do.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Link: https://lore.kernel.org/r/20250410011839.64418-9-nico@fluxnic.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This provides ucs_recompose() to recompose two Unicode characters into
a single character if possible. This is needed for the VT to properly
display decomposed UTF8 sequences.
Note: scripts/checkpatch.pl complains about "... exceeds 100 columns".
Please ignore.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Link: https://lore.kernel.org/r/20250410011839.64418-8-nico@fluxnic.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The generated code includes a table that maps base character + combining
mark pairs to their precomposed equivalents using Python's unicodedata
module. It also provides the ucs_recompose() function to query that
table.
The default script behavior is to create a table with most commonly used
Latin, Greek, and Cyrillic recomposition pairs only. It is much smaller
than the table with all possible recomposition pairs (71 entries vs 1000
entries). But if one needs/wants the full table then simply running the
script with the --full argument will generate it.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Link: https://lore.kernel.org/r/20250410011839.64418-7-nico@fluxnic.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This replaces ucs_width.c with the code generated by gen_ucs_width.py
providing comprehensive tables for double-width and zero-width Unicode
code points. Also make ucs_is_zero_width() effective.
Note: scripts/checkpatch.pl complains about "... exceeds 100 columns".
Please ignore.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Link: https://lore.kernel.org/r/20250410011839.64418-6-nico@fluxnic.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The table in the current ucs_width.c is terribly out of date and
incomplete. We also need a second table to store zero-width code points.
Properly maintaining those tables manually is impossible. So here's a
script to automatically generate them.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Link: https://lore.kernel.org/r/20250410011839.64418-5-nico@fluxnic.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Zero-width Unicode code points are causing misalignment in vertically
aligned content, disrupting the visual layout. Let's handle zero-width
code points more intelligently.
Double-width code points are stored in the screen grid followed by a white
space code point to create the expected screen layout. When a double-width
code point is followed by a zero-width code point in the console incoming
bytestream (e.g., an emoji with a presentation selector) then we may
replace the white space padding by that zero-width code point instead of
dropping it. This maximize screen content information while preserving
proper layout.
If a zero-width code point is preceded by a single-width code point then
the above trick is not possible and such zero-width code point must
be dropped.
VS16 (Variation Selector 16, U+FE0F) is special as it doubles the width
of the preceding single-width code point. We handle that case by giving
VS16 a width of 1 when that happens.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Link: https://lore.kernel.org/r/20250410011839.64418-4-nico@fluxnic.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This will make it easier to maintain. Also make it depend on
CONFIG_CONSOLE_TRANSLATIONS.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Link: https://lore.kernel.org/r/20250410011839.64418-3-nico@fluxnic.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
devm_ioremap() can return NULL on error. Currently, mlb_usio_probe()
does not check for this case, which could result in a NULL pointer
dereference.
Add NULL check after devm_ioremap() to prevent this issue.
Fixes: ba44dc0430 ("serial: Add Milbeaut serial control")
Signed-off-by: Henry Martin <bsdhenrymartin@gmail.com>
Link: https://lore.kernel.org/r/20250403070339.64990-1-bsdhenrymartin@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SpacemiT UART requires a bus clock to be enabled, in addition to
it's "normal" core clock. Look up the optional bus clock by name,
and if that's found, look up the core clock using the name "core".
Supplying a bus clock is optional. If no bus clock is needed, the
the first/only clock is used for the core clock.
Signed-off-by: Alex Elder <elder@riscstar.com>
Link: https://lore.kernel.org/r/20250409192213.1130181-3-elder@riscstar.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
struct gpio_chip now has callbacks for setting line values that return
an integer, allowing to indicate failures. Convert the driver to using
them.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20250408-gpiochip-set-rv-tty-v1-2-fb49444827d4@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
struct gpio_chip now has callbacks for setting line values that return
an integer, allowing to indicate failures. Convert the driver to using
them.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20250408-gpiochip-set-rv-tty-v1-1-fb49444827d4@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove unnecessary semicolons reported by Coccinelle/coccicheck and the
semantic patch at scripts/coccinelle/misc/semicolon.cocci.
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Link: https://lore.kernel.org/r/20250407040712.2577607-1-nichen@iscas.ac.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The absence of an alias in the device tree results in an invalid line
number, causing the driver probe to fail for GENI serial.
To prevent probe failures, dynamically assign line numbers if an alias is
not present in the device tree for non-console ports.
Signed-off-by: Viken Dadhaniya <quic_vdadhani@quicinc.com>
Link: https://lore.kernel.org/r/20250327070711.2585887-1-quic_vdadhani@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When two instances of uart devices are probing, a concurrency race can
occur. If one thread calls uart_register_driver function, which first
allocates and assigns memory to 'uart_state' member of uart_driver
structure, the other instance can bypass uart driver registration and
call ulite_assign. This calls uart_add_one_port, which expects the uart
driver to be fully initialized. This leads to a kernel panic due to a
null pointer dereference:
[ 8.143581] BUG: kernel NULL pointer dereference, address: 00000000000002b8
[ 8.156982] #PF: supervisor write access in kernel mode
[ 8.156984] #PF: error_code(0x0002) - not-present page
[ 8.156986] PGD 0 P4D 0
...
[ 8.180668] RIP: 0010:mutex_lock+0x19/0x30
[ 8.188624] Call Trace:
[ 8.188629] ? __die_body.cold+0x1a/0x1f
[ 8.195260] ? page_fault_oops+0x15c/0x290
[ 8.209183] ? __irq_resolve_mapping+0x47/0x80
[ 8.209187] ? exc_page_fault+0x64/0x140
[ 8.209190] ? asm_exc_page_fault+0x22/0x30
[ 8.209196] ? mutex_lock+0x19/0x30
[ 8.223116] uart_add_one_port+0x60/0x440
[ 8.223122] ? proc_tty_register_driver+0x43/0x50
[ 8.223126] ? tty_register_driver+0x1ca/0x1e0
[ 8.246250] ulite_probe+0x357/0x4b0 [uartlite]
To prevent it, move uart driver registration in to init function. This
will ensure that uart_driver is always registered when probe function
is called.
Signed-off-by: Jakub Lewalski <jakub.lewalski@nokia.com>
Signed-off-by: Elodie Decerle <elodie.decerle@nokia.com>
Link: https://lore.kernel.org/r/20250331160732.2042-1-elodie.decerle@nokia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Function dev_err() is redundant because platform_get_irq()
already prints an error.
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Acked-by: Mukesh Kumar Savaliya <quic_msavaliy@quicinc.com>
Link: https://lore.kernel.org/r/20250401080337.2187400-1-nichen@iscas.ac.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tidy up ACPI ID table:
- drop ACPI_PTR() and hence replace acpi.h with mod_devicetable.h et al.
- drop comma in the terminator entry
With that done, extend compile test coverage.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Chaitanya Vadrevu <chaitanya.vadrevu@emerson.com>
Reviewed-by: Chaitanya Vadrevu <chaitanya.vadrevu@emerson.com>
Link: https://lore.kernel.org/r/20250321182119.454507-8-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to use dev_err_probe() to simplify the error path and
unify a message template.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Chaitanya Vadrevu <chaitanya.vadrevu@emerson.com>
Reviewed-by: Chaitanya Vadrevu <chaitanya.vadrevu@emerson.com>
Link: https://lore.kernel.org/r/20250321182119.454507-7-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are serial_port_in()/serial_port_out() helpers to be used
instead of direct p->serial_in()/p->serial_out().
Use them in various 8250 drivers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Chaitanya Vadrevu <chaitanya.vadrevu@emerson.com>
Reviewed-by: Chaitanya Vadrevu <chaitanya.vadrevu@emerson.com>
Link: https://lore.kernel.org/r/20250321182119.454507-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It doesn't matter if the properties are supplied or not in
the struct ni16550_device_info as default in any case is 0.
Hence there is no need to check for them being set.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Chaitanya Vadrevu <chaitanya.vadrevu@emerson.com>
Reviewed-by: Chaitanya Vadrevu <chaitanya.vadrevu@emerson.com>
Link: https://lore.kernel.org/r/20250321182119.454507-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to use new platform_get_mem_or_io() instead of home grown analogue.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Chaitanya Vadrevu <chaitanya.vadrevu@emerson.com>
Reviewed-by: Chaitanya Vadrevu <chaitanya.vadrevu@emerson.com>
Link: https://lore.kernel.org/r/20250321182119.454507-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UPF_IOREMAP is for serial core to map the resource on behalf of the
driver. No need to perform this explicitly in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Chaitanya Vadrevu <chaitanya.vadrevu@emerson.com>
Reviewed-by: Chaitanya Vadrevu <chaitanya.vadrevu@emerson.com>
Link: https://lore.kernel.org/r/20250321182119.454507-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we have now a common helper to read port properties
use it instead of sparse home grown solution.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Chaitanya Vadrevu <chaitanya.vadrevu@emerson.com>
Reviewed-by: Chaitanya Vadrevu <chaitanya.vadrevu@emerson.com>
Link: https://lore.kernel.org/r/20250321182119.454507-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
timer_delete[_sync]() replaces del_timer[_sync](). Convert the whole tree
over and remove the historical wrapper inlines.
Conversion was done with coccinelle plus manual fixups where necessary.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Here is the big set of serial and tty driver updates for 6.15-rc1.
Include in here are the following:
- more great tty layer cleanups from Jiri. Someday this will be done,
but that's not going to be any year soon...
- kdb debug driver reverts to fix a reported issue
- lots of .dts binding updates for different devices with serial
devices
- lots of tiny updates and tweaks and a few bugfixes for different
serial drivers.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZ+2YPA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yn2OQCgvxCyoeuNPuV4X89JdrgocMTMyTYAn15pGgDa
r7w9UDO/D7UqRnKEnFy+
=lJwK
-----END PGP SIGNATURE-----
Merge tag 'tty-6.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big set of serial and tty driver updates for 6.15-rc1.
Include in here are the following:
- more great tty layer cleanups from Jiri. Someday this will be done,
but that's not going to be any year soon...
- kdb debug driver reverts to fix a reported issue
- lots of .dts binding updates for different devices with serial
devices
- lots of tiny updates and tweaks and a few bugfixes for different
serial drivers.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-6.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (79 commits)
tty: serial: fsl_lpuart: Fix unused variable 'sport' build warning
serial: stm32: do not deassert RS485 RTS GPIO prematurely
serial: 8250: add driver for NI UARTs
dt-bindings: serial: snps-dw-apb-uart: document RZ/N1 binding without DMA
serial: icom: fix code format problems
serial: sh-sci: Save and restore more registers
tty: serial: pl011: remove incorrect of_match_ptr annotation
dt-bindings: serial: snps-dw-apb-uart: Add support for rk3562
tty: serial: lpuart: only disable CTS instead of overwriting the whole UARTMODIR register
tty: caif: removed unused function debugfs_tx()
serial: 8250_dma: terminate correct DMA in tx_dma_flush()
tty: serial: fsl_lpuart: rename register variables more specifically
tty: serial: fsl_lpuart: use port struct directly to simply code
tty: serial: fsl_lpuart: Use u32 and u8 for register variables
tty: serial: fsl_lpuart: disable transmitter before changing RS485 related registers
tty: serial: 8250: Add Brainboxes XC devices
dt-bindings: serial: fsl-lpuart: support i.MX94
tty: serial: 8250: Add some more device IDs
dt-bindings: serial: samsung: add exynos7870-uart compatible
serial: 8250_dw: Comment possible corner cases in serial_out() implementation
...
- Add sorting of mcount locations at build time
- Rework uaccess functions with C exception handling to shorten inline
assembly size and enable full inlining. This yields near-optimal code
for small constant copies with a ~40kb kernel size increase
- Add support for a configurable STRICT_MM_TYPECHECKS which allows to
generate better code, but also allows to have type checking for
debug builds
- Optimize get_lowcore() for common callers with alternatives that
nearly revert to the pre-relocated lowcore code, while also slightly
reducing syscall entry and exit time
- Convert MACHINE_HAS_* checks for single facility tests into cpu_has_*
style macros that call test_facility(), and for features with additional
conditions, add a new ALT_TYPE_FEATURE alternative to provide a static
branch via alternative patching. Also, move machine feature detection
to the decompressor for early patching and add debugging functionality
to easily show which alternatives are patched
- Add exception table support to early boot / startup code to get rid
of the open coded exception handling
- Use asm_inline for all inline assemblies with EX_TABLE or ALTERNATIVE
to ensure correct inlining and unrolling decisions
- Remove 2k page table leftovers now that s390 has been switched to
always allocate 4k page tables
- Split kfence pool into 4k mappings in arch_kfence_init_pool() and
remove the architecture-specific kfence_split_mapping()
- Use READ_ONCE_NOCHECK() in regs_get_kernel_stack_nth() to silence
spurious KASAN warnings from opportunistic ftrace argument tracing
- Force __atomic_add_const() variants on s390 to always return void,
ensuring compile errors for improper usage
- Remove s390's ioremap_wt() and pgprot_writethrough() due to mismatched
semantics and lack of known users, relying on asm-generic fallbacks
- Signal eventfd in vfio-ap to notify userspace when the guest AP
configuration changes, including during mdev removal
- Convert mdev_types from an array to a pointer in vfio-ccw and vfio-ap
drivers to avoid fake flex array confusion
- Cleanup trap code
- Remove references to the outdated linux390@de.ibm.com address
- Other various small fixes and improvements all over the code
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE3QHqV+H2a8xAv27vjYWKoQLXFBgFAmfmuPwACgkQjYWKoQLX
FBgTDAgAjKmZ5OYjACRfYepTvKk9SDqa2CBlQZ+BhbAXEVIrxKnv8OkImAXoWNsM
mFxiCxAHWdcD+nqTrxFsXhkNLsndijlwnj/IqZgvy6R/3yNtBlAYRPLujOmVrsQB
dWB8Dl38p63Ip1JfAqyabiAOUjfhrclRcM5FX5tgciXA6N/vhY3OM6k0+k7wN4Nj
Dei/rCrnYRXTrFQgtM4w8JTIrwdnXjeKvaTYCflh4Q5ISJ7TceSF7cqq8HOs5hhK
o2ciaoTdx212522CIsxeN3Ls3jrn8bCOCoOeSCysc5RL84grAuFnmjSajo1LFide
S/TQtHXYy78Wuei9xvHi561ogiv/ww==
=Kxgc
-----END PGP SIGNATURE-----
Merge tag 's390-6.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Vasily Gorbik:
- Add sorting of mcount locations at build time
- Rework uaccess functions with C exception handling to shorten inline
assembly size and enable full inlining. This yields near-optimal code
for small constant copies with a ~40kb kernel size increase
- Add support for a configurable STRICT_MM_TYPECHECKS which allows to
generate better code, but also allows to have type checking for debug
builds
- Optimize get_lowcore() for common callers with alternatives that
nearly revert to the pre-relocated lowcore code, while also slightly
reducing syscall entry and exit time
- Convert MACHINE_HAS_* checks for single facility tests into cpu_has_*
style macros that call test_facility(), and for features with
additional conditions, add a new ALT_TYPE_FEATURE alternative to
provide a static branch via alternative patching. Also, move machine
feature detection to the decompressor for early patching and add
debugging functionality to easily show which alternatives are patched
- Add exception table support to early boot / startup code to get rid
of the open coded exception handling
- Use asm_inline for all inline assemblies with EX_TABLE or ALTERNATIVE
to ensure correct inlining and unrolling decisions
- Remove 2k page table leftovers now that s390 has been switched to
always allocate 4k page tables
- Split kfence pool into 4k mappings in arch_kfence_init_pool() and
remove the architecture-specific kfence_split_mapping()
- Use READ_ONCE_NOCHECK() in regs_get_kernel_stack_nth() to silence
spurious KASAN warnings from opportunistic ftrace argument tracing
- Force __atomic_add_const() variants on s390 to always return void,
ensuring compile errors for improper usage
- Remove s390's ioremap_wt() and pgprot_writethrough() due to
mismatched semantics and lack of known users, relying on asm-generic
fallbacks
- Signal eventfd in vfio-ap to notify userspace when the guest AP
configuration changes, including during mdev removal
- Convert mdev_types from an array to a pointer in vfio-ccw and vfio-ap
drivers to avoid fake flex array confusion
- Cleanup trap code
- Remove references to the outdated linux390@de.ibm.com address
- Other various small fixes and improvements all over the code
* tag 's390-6.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (78 commits)
s390: Use inline qualifier for all EX_TABLE and ALTERNATIVE inline assemblies
s390/kfence: Split kfence pool into 4k mappings in arch_kfence_init_pool()
s390/ptrace: Avoid KASAN false positives in regs_get_kernel_stack_nth()
s390/boot: Ignore vmlinux.map
s390/sysctl: Remove "vm/allocate_pgste" sysctl
s390: Remove 2k vs 4k page table leftovers
s390/tlb: Use mm_has_pgste() instead of mm_alloc_pgste()
s390/lowcore: Use lghi instead llilh to clear register
s390/syscall: Merge __do_syscall() and do_syscall()
s390/spinlock: Implement SPINLOCK_LOCKVAL with inline assembly
s390/smp: Implement raw_smp_processor_id() with inline assembly
s390/current: Implement current with inline assembly
s390/lowcore: Use inline qualifier for get_lowcore() inline assembly
s390: Move s390 sysctls into their own file under arch/s390
s390/syscall: Simplify syscall_get_arguments()
s390/vfio-ap: Notify userspace that guest's AP config changed when mdev removed
s390: Remove ioremap_wt() and pgprot_writethrough()
s390/mm: Add configurable STRICT_MM_TYPECHECKS
s390/mm: Convert pgste_val() into function
s390/mm: Convert pgprot_val() into function
...
-----BEGIN PGP SIGNATURE-----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=lNTZ
-----END PGP SIGNATURE-----
Merge tag 'printk-for-6.15' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux
Pull printk updates from Petr Mladek:
- New option "printk.debug_non_panic_cpus" allows to store printk
messages from non-panic CPUs during panic. It might be useful when
panic() fails. It is disabled by default because it increases the
chance to see the messages printed before panic() and on the
panic-CPU.
- New build option "CONFIG_NULL_TTY_DEFAULT_CONSOLE" allows to build
kernel without the virtual terminal support which prefers ttynull
over serial console.
- Do not unblank suspended consoles.
- Some code clean up.
* tag 'printk-for-6.15' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux:
printk/panic: Add option to allow non-panic CPUs to write to the ring buffer.
printk: Add an option to allow ttynull to be a default console device
printk: Check CON_SUSPEND when unblanking a console
printk: Rename console_start to console_resume
printk: Rename console_stop to console_suspend
printk: Rename resume_console to console_resume_all
printk: Rename suspend_console to console_suspend_all
If stm32_usart_start_tx is called with an empty xmit buffer, RTS GPIO
could be deasserted prematurely, as bytes in TX FIFO are still
transmitting.
So this patch remove rts disable when xmit buffer is empty.
Fixes: d7c7671616 ("serial: stm32: Use TC interrupt to deassert GPIO RTS in RS485 mode")
Cc: stable <stable@kernel.org>
Signed-off-by: Cheick Traore <cheick.traore@foss.st.com>
Link: https://lore.kernel.org/r/20250320152540.709091-1-cheick.traore@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The National Instruments (NI) 16550 is a 16550-like UART with larger
FIFOs and embedded RS-232/RS-485 transceiver control circuitry. This
patch adds a driver that can operate this UART, which is used for
onboard serial ports in several NI embedded controller designs.
Portions of this driver were originally written by Jaeden Amero and
Karthik Manamcheri, with extensive cleanups and refactors since by
Brenda Streiff.
Cc: Gratian Crisan <gratian.crisan@emerson.com>
Co-developed-by: Jason Smith <jason.smith@emerson.com>
Signed-off-by: Jason Smith <jason.smith@emerson.com>
Signed-off-by: Chaitanya Vadrevu <chaitanya.vadrevu@emerson.com>
Link: https://lore.kernel.org/r/a3b0df6d-1dd5-4cc4-a7e1-4ed51fb9e4cc@emerson.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix below inconsistent indenting smatch warning.
smatch warnings:
drivers/tty/serial/icom.c:1768 icom_probe() warn: inconsistent indenting
Removed that useless (void *), the code would fit on a single 100c line
Removed '{' and '}'.
Signed-off-by: Charles Han <hanchunchao@inspur.com>
Link: https://lore.kernel.org/r/20250305095120.7518-1-hanchunchao@inspur.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On (H)SCIF with a Baud Rate Generator for External Clock (BRG), there
are multiple ways to configure the requested serial speed. If firmware
uses a different method than Linux, and if any debug info is printed
after the Bit Rate Register (SCBRR) is restored, but before termios is
reconfigured (which configures the alternative method), the system may
lock-up during resume.
Fix this by saving and restoring the contents of the BRG Frequency
Division (SCDL) and Clock Select (SCCKS) registers as well.
Also save and restore the HSCIF's Sampling Rate Register (HSSRR), which
configures the sampling point, and the SCIFA/SCIFB's Serial Port Control
and Data Registers (SCPCR/SCPDR), which configure the optional control
flow signals.
After this, all registers that are not saved/restored are either:
- read-only,
- write-only,
- status registers containing flags with clear-after-set semantics,
- FIFO Data Count Trigger registers, which do not matter much for
the serial console.
Fixes: 22a6984c5b ("serial: sh-sci: Update the suspend/resume support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/11c2eab45d48211e75d8b8202cce60400880fe55.1741114989.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Building with W=1 shows a warning about sbsa_uart_of_match being unused when
CONFIG_OF is disabled:
drivers/tty/serial/amba-pl011.c:2945:34: error: unused variable 'sbsa_uart_of_match' [-Werror,-Wunused-const-variable]
The driver is not actually used on any machines that are built
with CONFIG_OF disabled, so using of_match_ptr() won't save any
actual memory, and it can be best removed.
The corresponding ACPI_PTR() annotation does save a few bytes on
32-bit arm since CONFIG_ACPI is not available, but for consistency
it seems better to remove both along with the __maybe_unused
annotation on the ACPI table.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20250225163556.4169086-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No need to overwrite the whole UARTMODIR register before waiting the
transmit engine complete, actually our target here is only to disable
CTS flow control to avoid the dirty data in TX FIFO may block the
transmit engine complete.
Also delete the following duplicate CTS disable configuration.
Fixes: d5a2e08343 ("tty: serial: lpuart: disable flow control while waiting for the transmit engine to complete")
Cc: stable <stable@kernel.org>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20250307065446.1122482-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When flushing transmit side DMA, it is the transmit channel that should
be terminated, not the receive channel.
Fixes: 9e512eaaf8 ("serial: 8250: Fix fifo underflow on flush")
Cc: stable <stable@kernel.org>
Reported-by: Wentao Guan <guanwentao@uniontech.com>
Signed-off-by: John Keeping <jkeeping@inmusicbrands.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20250224121831.1429323-1-jkeeping@inmusicbrands.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are many fuzzy register variables in the lpuart driver, such as
temp, tmp, val, reg. Let's give these register variables more specific
names.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20250312023904.1343351-4-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Most lpuart functions have the parameter struct uart_port *port, but
still use the &sport->port to get the uart_port instead of use it
directly, let's simply the code logic, directly use this struct instead
of covert it from struct sport.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20250312023904.1343351-3-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use u32 and u8 rather than unsigned long or unsigned char for register
variables for clarity and consistency.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20250312023904.1343351-2-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the LPUART reference manual, TXRTSE and TXRTSPOL of MODIR
register only can be changed when the transmitter is disabled.
So disable the transmitter before changing RS485 related registers and
re-enable it after the change is done.
Fixes: 67b0183786 ("tty: serial: lpuart: Add RS485 support for 32-bit uart flavour")
Cc: stable <stable@kernel.org>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250312022503.1342990-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
8250 DesignWare driver uses a few custom implementations of the serial_out().
These implementations are carefully made to avoid infinite loops. But this is
not obvious from looking at the code. Comment the possible corner cases in
the respective functions.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250317094021.1201512-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
change_irq and change_port are boolean variables. Mark them as such
(instead of uint).
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250317070046.24386-32-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Return immediately from the error locations or switch-case ends. It is
therefore easier to see the flow.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250317070046.24386-31-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is unnecessary here and makes the code harder to follow. Invert the
condition and drop the goto+label.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250317070046.24386-30-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Use already defined 'port' for fetching start/offset, and size.
* Return from the switch immediately -- so it is clear what is returned
and when.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250317070046.24386-29-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are serial_port_in/out() helpers to be used instead of direct
p->serial_in/out(). Use them in various 8250 drivers.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Cc: "Ilpo Järvinen" <ilpo.jarvinen@linux.intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
--
[v2]
* Use serial_port_in/out() and not serial_in/out() [Andy]
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> # 8250_dw
Link: https://lore.kernel.org/r/20250317070046.24386-28-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_line_info() wants to work with struct uart_state. Do not pass a
driver and an index. Pass the precomputed struct directly.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250317070046.24386-27-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The linking is done implicitly by tty_port_register_device_attr_serdev()
few lines below. So drop this explicit tty_port_link_device().
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250317070046.24386-26-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
They are simple wrappers around serial_{in/out}() without actually
pausing the execution. Since ever. So drop these useless wrappers.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: sparclinux@vger.kernel.org
Link: https://lore.kernel.org/r/20250317070046.24386-24-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These ioctls are undocumented and not exposed -- they are defined
locally. Given they need a special tty_port just for them, this is very
ugly. So drop this whole functionality. It is barely used for something
real. (And if it is, we'd need a common functionality to all drivers.)
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250317070046.24386-21-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I doubt anyone actually uses this driver (unlike mxser.c and serial
moxa driven devices). Even less there is anyone with a moxa ISA card.
The newer mxser dropped the support for ISA in 2021. Let this moxa
follow now.
Good diet.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250317070046.24386-20-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The arbitrary MOXA_VERSION is dumped to the logs when the driver is
loaded. Avoid this as a driver should be silent unless something breaks.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250317070046.24386-19-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In particular, serdev_device_write_room() is not called, so the whole
serdev's write_room() can go.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20250317070046.24386-17-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__tty_alloc_driver()'s kernel-doc needed some care: describe the return
value using the standard "Returns:", and use the new enum tty_driver_flag
for @flags.
Then, the tty_alloc_driver() macro was undocumented, but referenced many
times in the docs. Copy the docs from the above (except the @owner
parameter, obviously).
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250317070046.24386-15-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
n_tty_read() contains "we need more data" handling deep in that
function. And there is also a label (more_to_be_read) as we handle this
situation from two places.
It makes more sense to have all "return"s accumulated at the end of
functions. And "goto" from multiple places there. Therefore, do this
with the "more_to_be_read" label in n_tty_read().
After this and the previous changes, n_tty_read() is now much more
easier to follow.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250317070046.24386-12-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
n_tty_read() is a very long function doing too much of different stuff.
Extract the "wait for input" to a separate function:
n_tty_wait_for_input(). It returns an error (< 0), no input (0), or has
potential input (1).
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250317070046.24386-11-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
n_tty_read() is a very long function doing too much of different stuff.
Extract the "cookie" (continuation read) handling to a separate
function: n_tty_continue_cookie().
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250317070046.24386-10-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This n_tty_trace() is an always disabled debugging macro. It comes from
commit 32f13521ca ("n_tty: Line copy to user buffer in canonical
mode").
Drop it as it is dead for over a decade.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250317070046.24386-9-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Use guard(mutex), which results in:
- the function can return directly when "space == 0".
- "i" can now be "unsigned" as it is no longer abused to hold a retval
from tty->ops->write(). Note the compared-to "nr" is already
"unsigned".
* The end label is now dubbed "do_write" as that is what happens there.
Unlike the uncertain "break_out" name.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250317070046.24386-8-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty_write_room() returns an "unsigned int". So in case some insane
driver (like my tty test driver) returns (legitimate) UINT_MAX from its
tty_operations::write_room(), n_tty is confused on several places.
For example, in process_output_block(), the result of tty_write_room()
is stored into (signed) "int". So this UINT_MAX suddenly becomes -1. And
that is extended to ssize_t and returned from process_output_block().
This causes a write() to such a node to receive -EPERM (which is -1).
Fix that by using proper "unsigned int" and proper "== 0" test. And
return 0 constant directly in that "if", so that it is immediately clear
what is returned ("space" equals to 0 at that point).
Similarly for process_output() and __process_echoes().
Note this does not fix any in-tree driver as of now.
If you want "Fixes: something", it would be commit 03b3b1a240 ("tty:
make tty_operations::write_room return uint"). I intentionally do not
mark this patch by a real tag below.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250317070046.24386-6-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"N_TTY_BUF_SIZE" is private to n_tty and shall not be exposed to the
world. Definitely not in tty.h somewhere in the middle of "struct
tty_struct".
This is a remnant of moving "read_flags" to "struct n_tty_data" in
commit 3fe780b379 ("TTY: move ldisc data from tty_struct: bitmaps").
But some cleanup was needed first (in previous patches).
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250317070046.24386-5-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
N_TTY_BUF_SIZE -- as the name suggests -- is the N_TTY's buffer size.
There is no reason to couple that to audit's buffer size, so define an
own TTY_AUDIT_BUF_SIZE macro (with the same size).
N_TTY_BUF_SIZE is private and will be moved to n_tty.c later.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250317070046.24386-3-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The new option is CONFIG_NULL_TTY_DEFAULT_CONSOLE.
if enabled, and CONFIG_VT is disabled, ttynull will become the default
primary console device.
ttynull will be the only console device usually with this option enabled.
Some architectures do call add_preferred_console() which may add another
console though.
Motivation:
Many distributions ship with CONFIG_VT enabled. On tested desktop hardware
if CONFIG_VT is disabled, the default console device falls back to
/dev/ttyS0 instead of /dev/tty.
This could cause issues in user space, and hardware problems:
1. The user space issues include the case where /dev/ttyS0 is
disconnected, and the TCGETS ioctl, which some user space libraries use
as a probe to determine if a file is a tty, is called on /dev/console and
fails. Programs that call isatty() on /dev/console and get an incorrect
false value may skip expected logging to /dev/console.
2. The hardware issues include the case if a user has a science instrument
or other device connected to the /dev/ttyS0 port, and they were to upgrade
to a kernel that is disabling the CONFIG_VT option, kernel logs will then
be sent to the device connected to /dev/ttyS0 unless they edit their
kernel command line manually.
The new CONFIG_NULL_TTY_DEFAULT_CONSOLE option will give users and
distribution maintainers an option to avoid this. Disabling CONFIG_VT and
enabling CONFIG_NULL_TTY_DEFAULT_CONSOLE will ensure the default kernel
console behavior is not dependent on hardware configuration by default, and
avoid unexpected new behavior on devices connected to the /dev/ttyS0 serial
port.
Reviewed-by: Petr Mladek <pmladek@suse.com>
Tested-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Adam Simonelli <adamsimonelli@gmail.com>
Link: https://lore.kernel.org/r/20250314160749.3286153-2-adamsimonelli@gmail.com
[pmladek@suse.com: Fixed indentation of the commit message.]
Signed-off-by: Petr Mladek <pmladek@suse.com>
The intent of console_start was to resume a previously suspended console,
so rename it accordingly.
Signed-off-by: Marcos Paulo de Souza <mpdesouza@suse.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Reviewed-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20250226-printk-renaming-v1-4-0b878577f2e6@suse.com
[pmladek@suse.com: Fixed typo in the commit message. Updated also new drm_log.c.]
Signed-off-by: Petr Mladek <pmladek@suse.com>
The intent of console_stop was in fact to suspend it, so rename the
function accordingly.
Signed-off-by: Marcos Paulo de Souza <mpdesouza@suse.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Reviewed-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20250226-printk-renaming-v1-3-0b878577f2e6@suse.com
[pmladek@suse.com: Fixed typo in the commit message. Updated also new drm_log.c]
Signed-off-by: Petr Mladek <pmladek@suse.com>
Move machine type detection to the decompressor and use static branches
to implement and use machine_is_[lpar|vm|kvm]() instead of a runtime check
via MACHINE_IS_[LPAR|VM|KVM].
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
hrtimer_setup() takes the callback function pointer as argument and
initializes the timer completely.
Replace hrtimer_init() and the open coded initialization of
hrtimer::function with the new setup mechanism.
Patch was created by using Coccinelle.
Acked-by: Zack Rusin <zack.rusin@broadcom.com>
Signed-off-by: Nam Cao <namcao@linutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/4a028a23126b3350a5e243dcb49e1ef1b2a4b740.1738746904.git.namcao@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
hrtimer_setup() takes the callback function pointer as argument and
initializes the timer completely.
Replace hrtimer_init() and the open coded initialization of
hrtimer::function with the new setup mechanism.
Patch was created by using Coccinelle.
Acked-by: Zack Rusin <zack.rusin@broadcom.com>
Signed-off-by: Nam Cao <namcao@linutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/c21664d013015584aebbb6bb8cedd748182cb551.1738746904.git.namcao@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
hrtimer_setup() takes the callback function pointer as argument and
initializes the timer completely.
Replace hrtimer_init() and the open coded initialization of
hrtimer::function with the new setup mechanism.
Patch was created by using Coccinelle.
Acked-by: Zack Rusin <zack.rusin@broadcom.com>
Signed-off-by: Nam Cao <namcao@linutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/ad27070bc67c13f8a9acbd5cbf4cbae72797e3e1.1738746904.git.namcao@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
hrtimer_setup() takes the callback function pointer as argument and
initializes the timer completely.
Replace hrtimer_init() and the open coded initialization of
hrtimer::function with the new setup mechanism.
Patch was created by using Coccinelle.
Signed-off-by: Nam Cao <namcao@linutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/78e8c0d1b38998eab983fad265751ed13c2b9009.1738746904.git.namcao@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
hrtimer_setup() takes the callback function pointer as argument and
initializes the timer completely.
Replace hrtimer_init() and the open coded initialization of
hrtimer::function with the new setup mechanism.
Patch was created by using Coccinelle.
Acked-by: Zack Rusin <zack.rusin@broadcom.com>
Signed-off-by: Nam Cao <namcao@linutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/991926d130cc272df30d226760d5d74187991669.1738746904.git.namcao@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The field 'function' of struct hrtimer should not be changed directly, as
the write is lockless and a concurrent timer expiry might end up using the
wrong function pointer.
Switch to use hrtimer_update_function() which also performs runtime checks
that it is safe to modify the callback.
Signed-off-by: Nam Cao <namcao@linutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/af7823518fb060c6c97105a2513cfc61adbdf38f.1738746927.git.namcao@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following splat has been observed on a SAMA5D27 platform using
atmel_serial:
BUG: sleeping function called from invalid context at kernel/irq/manage.c:738
in_atomic(): 1, irqs_disabled(): 128, non_block: 0, pid: 27, name: kworker/u5:0
preempt_count: 1, expected: 0
INFO: lockdep is turned off.
irq event stamp: 0
hardirqs last enabled at (0): [<00000000>] 0x0
hardirqs last disabled at (0): [<c01588f0>] copy_process+0x1c4c/0x7bec
softirqs last enabled at (0): [<c0158944>] copy_process+0x1ca0/0x7bec
softirqs last disabled at (0): [<00000000>] 0x0
CPU: 0 UID: 0 PID: 27 Comm: kworker/u5:0 Not tainted 6.13.0-rc7+ #74
Hardware name: Atmel SAMA5
Workqueue: hci0 hci_power_on [bluetooth]
Call trace:
unwind_backtrace from show_stack+0x18/0x1c
show_stack from dump_stack_lvl+0x44/0x70
dump_stack_lvl from __might_resched+0x38c/0x598
__might_resched from disable_irq+0x1c/0x48
disable_irq from mctrl_gpio_disable_ms+0x74/0xc0
mctrl_gpio_disable_ms from atmel_disable_ms.part.0+0x80/0x1f4
atmel_disable_ms.part.0 from atmel_set_termios+0x764/0x11e8
atmel_set_termios from uart_change_line_settings+0x15c/0x994
uart_change_line_settings from uart_set_termios+0x2b0/0x668
uart_set_termios from tty_set_termios+0x600/0x8ec
tty_set_termios from ttyport_set_flow_control+0x188/0x1e0
ttyport_set_flow_control from wilc_setup+0xd0/0x524 [hci_wilc]
wilc_setup [hci_wilc] from hci_dev_open_sync+0x330/0x203c [bluetooth]
hci_dev_open_sync [bluetooth] from hci_dev_do_open+0x40/0xb0 [bluetooth]
hci_dev_do_open [bluetooth] from hci_power_on+0x12c/0x664 [bluetooth]
hci_power_on [bluetooth] from process_one_work+0x998/0x1a38
process_one_work from worker_thread+0x6e0/0xfb4
worker_thread from kthread+0x3d4/0x484
kthread from ret_from_fork+0x14/0x28
This warning is emitted when trying to toggle, at the highest level,
some flow control (with serdev_device_set_flow_control) in a device
driver. At the lowest level, the atmel_serial driver is using
serial_mctrl_gpio lib to enable/disable the corresponding IRQs
accordingly. The warning emitted by CONFIG_DEBUG_ATOMIC_SLEEP is due to
disable_irq (called in mctrl_gpio_disable_ms) being possibly called in
some atomic context (some tty drivers perform modem lines configuration
in regions protected by port lock).
Split mctrl_gpio_disable_ms into two differents APIs, a non-blocking one
and a blocking one. Replace mctrl_gpio_disable_ms calls with the
relevant version depending on whether the call is protected by some port
lock.
Suggested-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Acked-by: Richard Genoud <richard.genoud@bootlin.com>
Link: https://lore.kernel.org/r/20250217-atomic_sleep_mctrl_serial_gpio-v3-1-59324b313eef@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The field 'function' of struct hrtimer should not be changed directly, as
the write is lockless and a concurrent timer expiry might end up using the
wrong function pointer.
Switch to use hrtimer_update_function() which also performs runtime checks
that it is safe to modify the callback.
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/af7823518fb060c6c97105a2513cfc61adbdf38f.1738746927.git.namcao@linutronix.de
hrtimer_setup() takes the callback function pointer as argument and
initializes the timer completely.
Replace hrtimer_init() and the open coded initialization of
hrtimer::function with the new setup mechanism.
Patch was created by using Coccinelle.
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Zack Rusin <zack.rusin@broadcom.com>
Link: https://lore.kernel.org/all/4a028a23126b3350a5e243dcb49e1ef1b2a4b740.1738746904.git.namcao@linutronix.de
hrtimer_setup() takes the callback function pointer as argument and
initializes the timer completely.
Replace hrtimer_init() and the open coded initialization of
hrtimer::function with the new setup mechanism.
Patch was created by using Coccinelle.
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Zack Rusin <zack.rusin@broadcom.com>
Link: https://lore.kernel.org/all/c21664d013015584aebbb6bb8cedd748182cb551.1738746904.git.namcao@linutronix.de
hrtimer_setup() takes the callback function pointer as argument and
initializes the timer completely.
Replace hrtimer_init() and the open coded initialization of
hrtimer::function with the new setup mechanism.
Patch was created by using Coccinelle.
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Zack Rusin <zack.rusin@broadcom.com>
Link: https://lore.kernel.org/all/ad27070bc67c13f8a9acbd5cbf4cbae72797e3e1.1738746904.git.namcao@linutronix.de
hrtimer_setup() takes the callback function pointer as argument and
initializes the timer completely.
Replace hrtimer_init() and the open coded initialization of
hrtimer::function with the new setup mechanism.
Patch was created by using Coccinelle.
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/78e8c0d1b38998eab983fad265751ed13c2b9009.1738746904.git.namcao@linutronix.de
hrtimer_setup() takes the callback function pointer as argument and
initializes the timer completely.
Replace hrtimer_init() and the open coded initialization of
hrtimer::function with the new setup mechanism.
Patch was created by using Coccinelle.
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Zack Rusin <zack.rusin@broadcom.com>
Link: https://lore.kernel.org/all/991926d130cc272df30d226760d5d74187991669.1738746904.git.namcao@linutronix.de
Here are some small serial driver fixes for some reported problems for
6.14-rc3. Nothing major, just:
- sc16is7xx irq check fix
- 8250 fifo underflow fix
- serial_port and 8250 iotype fixes
Most of these have been in linux-next already, and all have passed 0-day
testing.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZ7H/YQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykxAwCbBpzMC3xtuqSw/PCrFGbBNeMVuQcAoKtoQYWr
Zro9O1hxTOfbFNeHEVtj
=XvcE
-----END PGP SIGNATURE-----
Merge tag 'tty-6.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull serial driver fixes from Greg KH:
"Here are some small serial driver fixes for some reported problems.
Nothing major, just:
- sc16is7xx irq check fix
- 8250 fifo underflow fix
- serial_port and 8250 iotype fixes
Most of these have been in linux-next already, and all have passed
0-day testing"
* tag 'tty-6.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: 8250: Fix fifo underflow on flush
serial: 8250_pnp: Remove unneeded ->iotype assignment
serial: 8250_platform: Remove unneeded ->iotype assignment
serial: 8250_of: Remove unneeded ->iotype assignment
serial: port: Make ->iotype validation global in __uart_read_properties()
serial: port: Always update ->iotype in __uart_read_properties()
serial: port: Assign ->iotype correctly when ->iobase is set
serial: sc16is7xx: Fix IRQ number check behavior
The Tegra264 SoC supports the UART Trace Controller (UTC), which allows
multiple firmware clients (up to 16) to share a single physical UART.
Each client is provided with its own interrupt and has access to a
128-character wide FIFO for both transmit (TX) and receive (RX)
operations.
Add tegra-utc driver to support Tegra UART Trace Controller (UTC)
client.
Signed-off-by: Kartik Rajput <kkartik@nvidia.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250213125612.4705-3-kkartik@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 0c57dfcc6c.
The functionality was supoosed to be used by a later patch in the
series that never landed [1]. Drop it.
NOTE: part of functionality was already reverted by commit
39d0be8743 ("serial: kgdb_nmi: Remove unused knock code"). Also note
that this revert is not a clean revert given code changes that have
happened in the meantime.
It's obvious that nobody is using this code since the two exposed
functions (kgdb_register_nmi_console() and
kgdb_unregister_nmi_console()) are both no-ops if
"arch_kgdb_ops.enable_nmi" is not defined. No architectures define it.
[1] https://lore.kernel.org/lkml/1348522080-32629-9-git-send-email-anton.vorontsov@linaro.org/
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: URL [1]
Link: https://lore.kernel.org/r/20250129082535.1.Ia095eac1ae357f87d23e7af2206741f5d40788f1@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Not all the cases provide the driver data, that is represented by
an object instance of struct dw8250_platform_data. Id est the change
missed the case when the driver is instantiated via board files as
pure platform driver. Fix this by calling dw8250_quirks() conditionally.
This will require splitting dw8250_setup_dma_filter() out of dw8250_quirks().
Also make sure IRQ handler won't crash, it also requires driver data
to be present.
Fixes: bfd3d4a40f ("serial: 8250_dw: Drop unneeded NULL checks in dw8250_quirks()")
Reported-by: kernel test robot <oliver.sang@intel.com>
Closes: https://lore.kernel.org/oe-lkp/202502121529.f7e65d49-lkp@intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250212115952.2312444-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Renesas RZ/G3S supports a power saving mode where power to most of the
SoC components is turned off. When returning from this power saving mode,
SoC components need to be re-configured.
The SCIFs on the Renesas RZ/G3S need to be re-configured as well when
returning from this power saving mode. The sh-sci code already configures
the SCIF clocks, power domain and registers by calling uart_resume_port()
in sci_resume(). On suspend path the SCIF UART ports are suspended
accordingly (by calling uart_suspend_port() in sci_suspend()). The only
missing setting is the reset signal. For this assert/de-assert the reset
signal on driver suspend/resume.
In case the no_console_suspend is specified by the user, the registers need
to be saved on suspend path and restore on resume path. To do this the
sci_console_save()/sci_console_restore() functions were added. There is no
need to cache/restore the status or FIFO registers. Only the control
registers. The registers that will be saved/restored on suspend/resume are
specified by the struct sci_suspend_regs data structure.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20250207113313.545432-1-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SoCs like the i.MX93 have several lpuart interfaces, but fsl_lpuart
uses the driver name to request the IRQ. This makes it hard to
identify interfaces from outputs like /proc/interrupts .
So use the dev_name() for requesting instead.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20250205091007.4528-1-wahrenst@gmx.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When flushing the serial port's buffer, uart_flush_buffer() calls
kfifo_reset() but if there is an outstanding DMA transfer then the
completion function will consume data from the kfifo via
uart_xmit_advance(), underflowing and leading to ongoing DMA as the
driver tries to transmit another 2^32 bytes.
This is readily reproduced with serial-generic and amidi sending even
short messages as closing the device on exit will wait for the fifo to
drain and in the underflow case amidi hangs for 30 seconds on exit in
tty_wait_until_sent(). A trace of that gives:
kworker/1:1-84 [001] 51.769423: bprint: serial8250_tx_dma: tx_size=3 fifo_len=3
amidi-763 [001] 51.769460: bprint: uart_flush_buffer: resetting fifo
irq/21-fe530000-76 [000] 51.769474: bprint: __dma_tx_complete: tx_size=3
irq/21-fe530000-76 [000] 51.769479: bprint: serial8250_tx_dma: tx_size=4096 fifo_len=4294967293
irq/21-fe530000-76 [000] 51.781295: bprint: __dma_tx_complete: tx_size=4096
irq/21-fe530000-76 [000] 51.781301: bprint: serial8250_tx_dma: tx_size=4096 fifo_len=4294963197
irq/21-fe530000-76 [000] 51.793131: bprint: __dma_tx_complete: tx_size=4096
irq/21-fe530000-76 [000] 51.793135: bprint: serial8250_tx_dma: tx_size=4096 fifo_len=4294959101
irq/21-fe530000-76 [000] 51.804949: bprint: __dma_tx_complete: tx_size=4096
Since the port lock is held in when the kfifo is reset in
uart_flush_buffer() and in __dma_tx_complete(), adding a flush_buffer
hook to adjust the outstanding DMA byte count is sufficient to avoid the
kfifo underflow.
Fixes: 9ee4b83e51 ("serial: 8250: Add support for dmaengine")
Cc: stable <stable@kernel.org>
Signed-off-by: John Keeping <jkeeping@inmusicbrands.com>
Link: https://lore.kernel.org/r/20250208124148.1189191-1-jkeeping@inmusicbrands.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The FMODE_NONOTIFY_* bits are a 2-bits mode. Open coding manipulation
of those bits is risky. Use an accessor file_set_fsnotify_mode() to
set the mode.
Rename file_set_fsnotify_mode() => file_set_fsnotify_mode_from_watchers()
to make way for the simple accessor name.
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Link: https://lore.kernel.org/r/20250203223205.861346-2-amir73il@gmail.com
Signed-off-by: Christian Brauner <brauner@kernel.org>
This reverts commit e12ebf14fa.
It causes build errors in linux-next.
Cc: Benjamin Larsson <benjamin.larsson@genexis.eu>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://lore.kernel.org/r/20250206135328.4bad1401@canb.auug.org.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If ->iobase is set the default will be UPIO_PORT for ->iotype after
the uart_read_and_validate_port_properties() call. Hence no need
to assign that explicitly. Otherwise it will be UPIO_MEM.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250124161530.398361-7-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If ->iobase is set the default will be UPIO_PORT for ->iotype after
the uart_read_and_validate_port_properties() call. Hence no need
to assign that explicitly. Otherwise it will be UPIO_MEM.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250124161530.398361-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If ->iobase is set the default will be UPIO_PORT for ->iotype after
the uart_read_and_validate_port_properties() call. Hence no need
to assign that explicitly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250124161530.398361-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to make code robust against potential changes in the future
move ->iotype validation outside of switch in __uart_read_properties().
If any code will be added in between that might leave the ->iotype value
unknown the validation catches this up.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250124161530.398361-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The documentation of the __uart_read_properties() states that
->iotype member is always altered after the function call, but
the code doesn't do that in the case when use_defaults == false
and the value of reg-io-width is unsupported. Make sure the code
follows the documentation.
Note, the current users of the uart_read_and_validate_port_properties()
will fail and the change doesn't affect their behaviour, neither
users of uart_read_port_properties() will be affected since the
alteration happens there even in the current code flow.
Fixes: e894b6005d ("serial: port: Introduce a common helper to read properties")
Cc: stable <stable@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250124161530.398361-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the ->iotype is always assigned to the UPIO_MEM when
the respective property is not found. However, this will not
support the cases when user wants to have UPIO_PORT to be set
or preserved. Support this scenario by checking ->iobase value
and default the ->iotype respectively.
Fixes: 1117a6fdc7 ("serial: 8250_of: Switch to use uart_read_port_properties()")
Fixes: e894b6005d ("serial: port: Introduce a common helper to read properties")
Cc: stable <stable@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250124161530.398361-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The logical meaning of the previous version is wrong due to a typo.
If the IRQ equals 0, no interrupt pin is available and polling mode
shall be used.
Additionally, this fix adds a check for IRQ < 0 to increase robustness,
because documentation still says that negative IRQ values cannot be
absolutely ruled-out.
Fixes: 104c1b9dde ("serial: sc16is7xx: Add polling mode if no IRQ pin is available")
Signed-off-by: Andre Werner <andre.werner@systec-electronic.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Maarten Brock <maarten.brock@sttls.nl>
Reviewed-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20250121071819.1346672-1-andre.werner@systec-electronic.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement the callbacks required for an NBCON console [0] on the
amba-pl011 console driver.
Referred to the NBCON implementation work for 8250 [1] and imx [2].
The normal-priority write_thread checks for console ownership
each time a character is printed.
write_atomic holds the console ownership until the entire string
is printed.
UART register operations are protected from other contexts by
uart_port_lock, except for a final flush(nbcon_atomic_flush_unsafe)
on panic.
The patch has been verified to correctly handle the output and
competition of messages with different priorities and flushing
panic message to console after nmi panic using ARM64 QEMU and
a physical machine(A64FX).
Stress testing was conducted on a physical machine(A64FX).
The results are as follows:
- The output speed and volume of messages using the NBCON console were
comparable to the legacy console (data suggests a slight improvement).
- When inducing a panic (sysrq-triggered or NMI) under heavy contention
on the serial console output,
the legacy console resulted in the loss of some or all crash messages.
However, using the NBCON console, no message loss occurred.
This testing referenced the NBCON console work for 8250 [3].
[0] https://lore.kernel.org/all/ZuRRTbapH0DCj334@pathway.suse.cz/
[1] https://lore.kernel.org/all/20240913140538.221708-1-john.ogness@linutronix.de/T/
[2] https://lore.kernel.org/linux-arm-kernel/20240913-serial-imx-nbcon-v3-1-4c627302335b@geanix.com/T/
[3] https://lore.kernel.org/lkml/ZsdoD6PomBRsB-ow@debarbos-thinkpadt14sgen2i.remote.csb/#t
Signed-off-by: Toshiyuki Sato <fj6611ie@aa.jp.fujitsu.com>
Link: https://lore.kernel.org/r/20250204044428.2191983-1-fj6611ie@aa.jp.fujitsu.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since platform data is being provided for all supported hardware,
no need to NULL check for it. Drop unneeded checks.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250203121456.3182891-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mctrl_gpio_free() was added in 2014 by
commit 84130aace8 ("tty/serial: Add GPIOLIB helpers for controlling
modem lines")
It does have a comment saying:
'- * Normally, this function will not be called, as the GPIOs will
- * be disposed of by the resource management code.'
indeed, it doesn't seem to have been used since it was added.
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Link: https://lore.kernel.org/r/20250129020048.245529-1-linux@treblig.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ldsem_down_write_trylock() was added in 2013 by
commit 4898e640ca ("tty: Add timed, writer-prioritized rw semaphore")
but hasn't been used.
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250122012559.441006-1-linux@treblig.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The legacy PM hook was never implemented. If we would like to achieve this,
the entire serial subsystem should switch to use runtime PM first. For now,
remove unneeded code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250117141313.592645-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The legacy PM hook was never implemented. If we would like to achieve this,
the entire serial subsystem should switch to use runtime PM first. For now,
remove unneeded code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250117141304.592611-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of driver core and debugfs updates for 6.14-rc1.
It's coming late in the merge cycle as there are a number of merge
conflicts with your tree now, and I wanted to make sure they were
working properly. To resolve them, look in linux-next, and I will send
the "fixup" patch as a response to the pull request.
Included in here is a bunch of driver core, PCI, OF, and platform rust
bindings (all acked by the different subsystem maintainers), hence the
merge conflict with the rust tree, and some driver core api updates to
mark things as const, which will also require some fixups due to new
stuff coming in through other trees in this merge window.
There are also a bunch of debugfs updates from Al, and there is at least
one user that does have a regression with these, but Al is working on
tracking down the fix for it. In my use (and everyone else's linux-next
use), it does not seem like a big issue at the moment.
Here's a short list of the things in here:
- driver core bindings for PCI, platform, OF, and some i/o functions.
We are almost at the "write a real driver in rust" stage now,
depending on what you want to do.
- misc device rust bindings and a sample driver to show how to use
them
- debugfs cleanups in the fs as well as the users of the fs api for
places where drivers got it wrong or were unnecessarily doing things
in complex ways.
- driver core const work, making more of the api take const * for
different parameters to make the rust bindings easier overall.
- other small fixes and updates
All of these have been in linux-next with all of the aforementioned
merge conflicts, and the one debugfs issue, which looks to be resolved
"soon".
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZ5koPA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymFHACfT5acDKf2Bov2Lc/5u3vBW/R6ChsAnj+LmgVI
hcDSPodj4szR40RRnzBd
=u5Ey
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core and debugfs updates from Greg KH:
"Here is the big set of driver core and debugfs updates for 6.14-rc1.
Included in here is a bunch of driver core, PCI, OF, and platform rust
bindings (all acked by the different subsystem maintainers), hence the
merge conflict with the rust tree, and some driver core api updates to
mark things as const, which will also require some fixups due to new
stuff coming in through other trees in this merge window.
There are also a bunch of debugfs updates from Al, and there is at
least one user that does have a regression with these, but Al is
working on tracking down the fix for it. In my use (and everyone
else's linux-next use), it does not seem like a big issue at the
moment.
Here's a short list of the things in here:
- driver core rust bindings for PCI, platform, OF, and some i/o
functions.
We are almost at the "write a real driver in rust" stage now,
depending on what you want to do.
- misc device rust bindings and a sample driver to show how to use
them
- debugfs cleanups in the fs as well as the users of the fs api for
places where drivers got it wrong or were unnecessarily doing
things in complex ways.
- driver core const work, making more of the api take const * for
different parameters to make the rust bindings easier overall.
- other small fixes and updates
All of these have been in linux-next with all of the aforementioned
merge conflicts, and the one debugfs issue, which looks to be resolved
"soon""
* tag 'driver-core-6.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (95 commits)
rust: device: Use as_char_ptr() to avoid explicit cast
rust: device: Replace CString with CStr in property_present()
devcoredump: Constify 'struct bin_attribute'
devcoredump: Define 'struct bin_attribute' through macro
rust: device: Add property_present()
saner replacement for debugfs_rename()
orangefs-debugfs: don't mess with ->d_name
octeontx2: don't mess with ->d_parent or ->d_parent->d_name
arm_scmi: don't mess with ->d_parent->d_name
slub: don't mess with ->d_name
sof-client-ipc-flood-test: don't mess with ->d_name
qat: don't mess with ->d_name
xhci: don't mess with ->d_iname
mtu3: don't mess wiht ->d_iname
greybus/camera - stop messing with ->d_iname
mediatek: stop messing with ->d_iname
netdevsim: don't embed file_operations into your structs
b43legacy: make use of debugfs_get_aux()
b43: stop embedding struct file_operations into their objects
carl9170: stop embedding file_operations into their objects
...
Here is the tty/serial driver set of changes for 6.14-rc1. Nothing
major in here, it was delayed a bit due to a regression found in
linux-next which has now been reverted and verified that it is fixed.
Other than the reverts, highlights include:
- 8250 work to get the nbcon mode working (partially reverted)
- altera_jtaguart minor fixes
- fsl_lpuart minor updates
- sh-sci driver minor updatesa
- other tiny driver updates and cleanups
All of these have been in linux-next for a while, and now with no
reports of problems (thanks to the reverts.)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZ5jnmQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymUzgCdFnanKtvIbBHv/RZJlu/t6MIofYkAn13dJjxQ
EGOYXDofSmMeGKL/V4Ie
=+GCR
-----END PGP SIGNATURE-----
Merge tag 'tty-6.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver updates from Greg KH:
"Here is the tty/serial driver set of changes for 6.14-rc1. Nothing
major in here, it was delayed a bit due to a regression found in
linux-next which has now been reverted and verified that it is fixed.
Other than the reverts, highlights include:
- 8250 work to get the nbcon mode working (partially reverted)
- altera_jtaguart minor fixes
- fsl_lpuart minor updates
- sh-sci driver minor updatesa
- other tiny driver updates and cleanups
All of these have been in linux-next for a while, and now with no
reports of problems (thanks to the reverts)"
* tag 'tty-6.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (44 commits)
Revert "serial: 8250: Switch to nbcon console"
Revert "serial: 8250: Revert "drop lockdep annotation from serial8250_clear_IER()""
serial: sh-sci: Increment the runtime usage counter for the earlycon device
serial: sh-sci: Clean sci_ports[0] after at earlycon exit
serial: sh-sci: Do not probe the serial port if its slot in sci_ports[] is in use
serial: sh-sci: Move runtime PM enable to sci_probe_single()
serial: sh-sci: Drop __initdata macro for port_cfg
serial: kgdb_nmi: Remove unused knock code
tty: Permit some TIOCL_SETSEL modes without CAP_SYS_ADMIN
tty: xilinx_uartps: split sysrq handling
serial: 8250: Revert "drop lockdep annotation from serial8250_clear_IER()"
serial: 8250: Switch to nbcon console
serial: 8250: Provide flag for IER toggling for RS485
serial: 8250: Use high-level writing function for FIFO
serial: 8250: Use frame time to determine timeout
serial: 8250: Adjust the timeout for FIFO mode
tty: atmel_serial: Use of_property_present() for non-boolean properties
serial: sc16is7xx: Add polling mode if no IRQ pin is available
dt-bindings: serial: sc16is7xx: Add description for polling mode
tty: serial: atmel: make it selectable for ARCH_LAN969X
...
this pull are:
- "lib min_heap: Improve min_heap safety, testing, and documentation"
from Kuan-Wei Chiu provides various tightenings to the min_heap library
code.
- "xarray: extract __xa_cmpxchg_raw" from Tamir Duberstein preforms some
cleanup and Rust preparation in the xarray library code.
- "Update reference to include/asm-<arch>" from Geert Uytterhoeven fixes
pathnames in some code comments.
- "Converge on using secs_to_jiffies()" from Easwar Hariharan uses the
new secs_to_jiffies() in various places where that is appropriate.
- "ocfs2, dlmfs: convert to the new mount API" from Eric Sandeen
switches two filesystems to the new mount API.
- "Convert ocfs2 to use folios" from Matthew Wilcox does that.
- "Remove get_task_comm() and print task comm directly" from Yafang Shao
removes now-unneeded calls to get_task_comm() in various places.
- "squashfs: reduce memory usage and update docs" from Phillip Lougher
implements some memory savings in squashfs and performs some
maintainability work.
- "lib: clarify comparison function requirements" from Kuan-Wei Chiu
tightens the sort code's behaviour and adds some maintenance work.
- "nilfs2: protect busy buffer heads from being force-cleared" from
Ryusuke Konishi fixes an issues in nlifs when the fs is presented with a
corrupted image.
- "nilfs2: fix kernel-doc comments for function return values" from
Ryusuke Konishi fixes some nilfs kerneldoc.
- "nilfs2: fix issues with rename operations" from Ryusuke Konishi
addresses some nilfs BUG_ONs which syzbot was able to trigger.
- "minmax.h: Cleanups and minor optimisations" from David Laight
does some maintenance work on the min/max library code.
- "Fixes and cleanups to xarray" from Kemeng Shi does maintenance work
on the xarray library code.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCZ5SP5QAKCRDdBJ7gKXxA
jqN7AQChvwXGG43n4d5SDiA/rH7ddvowQcDqhC9cAMJ1ReR7qwEA8/LIWDE4PdMX
mJnaZ1/ibpEpearrChCViApQtcyEGQI=
=ti4E
-----END PGP SIGNATURE-----
Merge tag 'mm-nonmm-stable-2025-01-24-23-16' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull non-MM updates from Andrew Morton:
"Mainly individually changelogged singleton patches. The patch series
in this pull are:
- "lib min_heap: Improve min_heap safety, testing, and documentation"
from Kuan-Wei Chiu provides various tightenings to the min_heap
library code
- "xarray: extract __xa_cmpxchg_raw" from Tamir Duberstein preforms
some cleanup and Rust preparation in the xarray library code
- "Update reference to include/asm-<arch>" from Geert Uytterhoeven
fixes pathnames in some code comments
- "Converge on using secs_to_jiffies()" from Easwar Hariharan uses
the new secs_to_jiffies() in various places where that is
appropriate
- "ocfs2, dlmfs: convert to the new mount API" from Eric Sandeen
switches two filesystems to the new mount API
- "Convert ocfs2 to use folios" from Matthew Wilcox does that
- "Remove get_task_comm() and print task comm directly" from Yafang
Shao removes now-unneeded calls to get_task_comm() in various
places
- "squashfs: reduce memory usage and update docs" from Phillip
Lougher implements some memory savings in squashfs and performs
some maintainability work
- "lib: clarify comparison function requirements" from Kuan-Wei Chiu
tightens the sort code's behaviour and adds some maintenance work
- "nilfs2: protect busy buffer heads from being force-cleared" from
Ryusuke Konishi fixes an issues in nlifs when the fs is presented
with a corrupted image
- "nilfs2: fix kernel-doc comments for function return values" from
Ryusuke Konishi fixes some nilfs kerneldoc
- "nilfs2: fix issues with rename operations" from Ryusuke Konishi
addresses some nilfs BUG_ONs which syzbot was able to trigger
- "minmax.h: Cleanups and minor optimisations" from David Laight does
some maintenance work on the min/max library code
- "Fixes and cleanups to xarray" from Kemeng Shi does maintenance
work on the xarray library code"
* tag 'mm-nonmm-stable-2025-01-24-23-16' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (131 commits)
ocfs2: use str_yes_no() and str_no_yes() helper functions
include/linux/lz4.h: add some missing macros
Xarray: use xa_mark_t in xas_squash_marks() to keep code consistent
Xarray: remove repeat check in xas_squash_marks()
Xarray: distinguish large entries correctly in xas_split_alloc()
Xarray: move forward index correctly in xas_pause()
Xarray: do not return sibling entries from xas_find_marked()
ipc/util.c: complete the kernel-doc function descriptions
gcov: clang: use correct function param names
latencytop: use correct kernel-doc format for func params
minmax.h: remove some #defines that are only expanded once
minmax.h: simplify the variants of clamp()
minmax.h: move all the clamp() definitions after the min/max() ones
minmax.h: use BUILD_BUG_ON_MSG() for the lo < hi test in clamp()
minmax.h: reduce the #define expansion of min(), max() and clamp()
minmax.h: update some comments
minmax.h: add whitespace around operators and after commas
nilfs2: do not update mtime of renamed directory that is not moved
nilfs2: handle errors that nilfs_prepare_chunk() may return
CREDITS: fix spelling mistake
...
In the sh-sci driver, serial ports are mapped to the sci_ports[] array,
with earlycon mapped at index zero.
The uart_add_one_port() function eventually calls __device_attach(),
which, in turn, calls pm_request_idle(). The identified code path is as
follows:
uart_add_one_port() ->
serial_ctrl_register_port() ->
serial_core_register_port() ->
serial_core_port_device_add() ->
serial_base_port_add() ->
device_add() ->
bus_probe_device() ->
device_initial_probe() ->
__device_attach() ->
// ...
if (dev->p->dead) {
// ...
} else if (dev->driver) {
// ...
} else {
// ...
pm_request_idle(dev);
// ...
}
The earlycon device clocks are enabled by the bootloader. However, the
pm_request_idle() call in __device_attach() disables the SCI port clocks
while earlycon is still active.
The earlycon write function, serial_console_write(), calls
sci_poll_put_char() via serial_console_putchar(). If the SCI port clocks
are disabled, writing to earlycon may sometimes cause the SR.TDFE bit to
remain unset indefinitely, causing the while loop in sci_poll_put_char()
to never exit. On single-core SoCs, this can result in the system being
blocked during boot when this issue occurs.
To resolve this, increment the runtime PM usage counter for the earlycon
SCI device before registering the UART port.
Fixes: 0b0cced19a ("serial: sh-sci: Add CONFIG_SERIAL_EARLYCON support")
Cc: stable@vger.kernel.org
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20250116182249.3828577-6-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The early_console_setup() function initializes sci_ports[0].port with an
object of type struct uart_port obtained from the struct earlycon_device
passed as an argument to early_console_setup().
Later, during serial port probing, the serial port used as earlycon
(e.g., port A) might be remapped to a different position in the sci_ports[]
array, and a different serial port (e.g., port B) might be assigned to slot
0. For example:
sci_ports[0] = port B
sci_ports[X] = port A
In this scenario, the new port mapped at index zero (port B) retains the
data associated with the earlycon configuration. Consequently, after the
Linux boot process, any access to the serial port now mapped to
sci_ports[0] (port B) will block the original earlycon port (port A).
To address this, introduce an early_console_exit() function to clean up
sci_ports[0] when earlycon is exited.
To prevent the cleanup of sci_ports[0] while the serial device is still
being used by earlycon, introduce the struct sci_port::probing flag and
account for it in early_console_exit().
Fixes: 0b0cced19a ("serial: sh-sci: Add CONFIG_SERIAL_EARLYCON support")
Cc: stable@vger.kernel.org
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20250116182249.3828577-5-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the sh-sci driver, sci_ports[0] is used by earlycon. If the earlycon is
still active when sci_probe() is called and the new serial port is supposed
to map to sci_ports[0], return -EBUSY to prevent breaking the earlycon.
This situation should occurs in debug scenarios, and users should be
aware of the potential conflict.
Fixes: 0b0cced19a ("serial: sh-sci: Add CONFIG_SERIAL_EARLYCON support")
Cc: stable@vger.kernel.org
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20250116182249.3828577-4-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Relocate the runtime PM enable operation to sci_probe_single(). This change
prepares the codebase for upcoming fixes.
While at it, replace the existing logic with a direct call to
devm_pm_runtime_enable() and remove sci_cleanup_single(). The
devm_pm_runtime_enable() function automatically handles disabling runtime
PM during driver removal.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20250116182249.3828577-3-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The port_cfg object is used by serial_console_write(), which serves as
the write function for the earlycon device. Marking port_cfg as __initdata
causes it to be freed after kernel initialization, resulting in earlycon
becoming unavailable thereafter. Remove the __initdata macro from port_cfg
to resolve this issue.
Fixes: 0b0cced19a ("serial: sh-sci: Add CONFIG_SERIAL_EARLYCON support")
Cc: stable@vger.kernel.org
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Fixes: 0b0cced19a ("serial: sh-sci: Add CONFIG_SERIAL_EARLYCON support")
Link: https://lore.kernel.org/r/20250116182249.3828577-2-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kgdb_nmi_poll_knock() has been unused since it was added in 2013 in
commit 0c57dfcc6c ("tty/serial: Add kgdb_nmi driver")
Remove it, the static helpers, and module parameters it used.
(The comment explaining why it might be used sounds sensible, but
it's never been wired up, perhaps it's worth doing somewhere?)
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Link: https://lore.kernel.org/r/20250112135759.105541-1-linux@treblig.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With this, processes without CAP_SYS_ADMIN are able to use TIOCLINUX with
subcode TIOCL_SETSEL, in the selection modes TIOCL_SETPOINTER,
TIOCL_SELCLEAR and TIOCL_SELMOUSEREPORT.
TIOCL_SETSEL was previously changed to require CAP_SYS_ADMIN, as this IOCTL
let callers change the selection buffer and could be used to simulate
keypresses. These three TIOCL_SETSEL selection modes, however, are safe to
use, as they do not modify the selection buffer.
This fixes a mouse support regression that affected Emacs (invisible mouse
cursor).
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/ee3ec63269b43b34e1c90dd8c9743bf8@finder.org
Fixes: 8d1b43f6a6 ("tty: Restrict access to TIOCLINUX' copy-and-paste subcommands")
Signed-off-by: Günther Noack <gnoack@google.com>
Reviewed-by: Kees Cook <kees@kernel.org>
Link: https://lore.kernel.org/r/20250110142122.1013222-1-gnoack@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
lockdep detects the following circular locking dependency:
CPU 0 CPU 1
========================== ============================
cdns_uart_isr() printk()
uart_port_lock(port) console_lock()
cdns_uart_console_write()
if (!port->sysrq)
uart_port_lock(port)
uart_handle_break()
port->sysrq = ...
uart_handle_sysrq_char()
printk()
console_lock()
The fixed commit attempts to avoid this situation by only taking the
port lock in cdns_uart_console_write if port->sysrq unset. However, if
(as shown above) cdns_uart_console_write runs before port->sysrq is set,
then it will try to take the port lock anyway. This may result in a
deadlock.
Fix this by splitting sysrq handling into two parts. We use the prepare
helper under the port lock and defer handling until we release the lock.
Fixes: 74ea66d4ca ("tty: xuartps: Improve sysrq handling")
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Cc: stable@vger.kernel.org # c980248179d: serial: xilinx_uartps: Use port lock wrappers
Acked-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20250110213822.2107462-1-sean.anderson@linux.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the debugfs / driver-core fixes in here as well for testing and
to build on top of.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since task->comm is guaranteed to be NUL-terminated, we can print it
directly without the need to copy it into a separate buffer. This
simplifies the code and avoids unnecessary operations.
Link: https://lkml.kernel.org/r/20241219023452.69907-6-laoar.shao@gmail.com
Signed-off-by: Yafang Shao <laoar.shao@gmail.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org> (For tty)
Reviewed-by: Lyude Paul <lyude@redhat.com> (For nouveau)
Cc: Oded Gabbay <ogabbay@kernel.org>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tursulin@ursulin.net>
Cc: David Airlie <airlied@gmail.com>
Cc: Simona Vetter <simona@ffwll.ch>
Cc: Karol Herbst <kherbst@redhat.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: Danilo Krummrich <dakr@redhat.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: "André Almeida" <andrealmeid@igalia.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Borislav Petkov (AMD) <bp@alien8.de>
Cc: Darren Hart <dvhart@infradead.org>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Morris <jmorris@namei.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Kalle Valo <kvalo@kernel.org>
Cc: Kees Cook <kees@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul Moore <paul@paul-moore.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Petr Mladek <pmladek@suse.com>
Cc: "Serge E. Hallyn" <serge@hallyn.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vineet Gupta <vgupta@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The 8250 driver no longer depends on @oops_in_progress and
will no longer violate the port->lock locking constraints.
This reverts commit 3d9e6f556e.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20250107212702.169493-7-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement the necessary callbacks to switch the 8250 console driver
to perform as an nbcon console.
Add implementations for the nbcon console callbacks:
->write_atomic()
->write_thread()
->device_lock()
->device_unlock()
and add CON_NBCON to the initial @flags.
All register access in the callbacks are within unsafe sections.
The ->write_atomic() and ->write_thread() callbacks allow safe
handover/takeover per byte and add a preceding newline if they
take over from another context mid-line.
For the ->write_atomic() callback, a new irq_work is used to defer
modem control since it may be called from a context that does not
allow waking up tasks.
Note: A new __serial8250_clear_IER() is introduced for direct
clearing of UART_IER. This will allow to restore the lockdep
check to serial8250_clear_IER() in a follow-up commit.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Tested-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20250107212702.169493-6-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For RS485 mode, if SER_RS485_RX_DURING_TX is not available, the
console ->write() callback needs to enable/disable Tx. It does
this by calling the ->rs485_start_tx() and ->rs485_stop_tx()
callbacks. However, some of these callbacks also disable/enable
interrupts and makes power management calls. This causes 2
problems for console writing:
1. A console write can occur in contexts that are illegal for
pm_runtime_*(). It is not even necessary for console writing
to use pm_runtime_*() because a console already does this in
serial8250_console_setup() and serial8250_console_exit().
2. The console ->write() callback already handles
disabling/enabling the interrupts by properly restoring the
previous IER value.
Add an argument @toggle_ier to the ->rs485_start_tx() and
->rs485_stop_tx() callbacks to specify if they may disable/enable
receive interrupts while using pm_runtime_*(). Console writing
will not allow the toggling.
For all call sites other than console writing there is no
functional change.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20250107212702.169493-5-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently serial8250_console_fifo_write() directly writes into
the UART_TX register rather than using the high-level function
serial8250_console_putchar(). This is because
serial8250_console_putchar() waits for the holding register to
become empty, which would defeat the purpose of the FIFO code.
Move the LSR_THRE waiting to a new function
serial8250_console_wait_putchar() so that the FIFO code can use
serial8250_console_putchar(). This will be particularly important
for a follow-up commit, where output bytes are inspected to track
newlines.
This is only refactoring and has no functional change.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20250107212702.169493-4-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rather than using a hard-coded per-character Tx-timeout of 10ms,
use the frame time to determine a timeout value. The value is
doubled to ensure that a timeout is only hit during unexpected
circumstances.
Since the frame time may not be available during early printing,
the previous 10ms value is kept as a fallback.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20250107212702.169493-3-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After a console has written a record into UART_TX, it uses
wait_for_xmitr() to wait until the data has been sent out before
returning. However, wait_for_xmitr() will timeout after 10ms,
regardless if the data has been transmitted or not.
For single bytes, this timeout is sufficient even at very slow
baud rates, such as 1200bps. However, when FIFO mode is used,
there may be 64 bytes pushed into the FIFO at once. At a baud
rate of 115200bps, the 10ms timeout is still sufficient. But
when using lower baud rates (such as 57600bps), the timeout
is _not_ sufficient. This causes longer lines to be cut off,
resulting in lost and horribly misformatted output on the
console.
When using FIFO mode, take the number of bytes into account to
determine an appropriate maximum timeout. Increasing the timeout
does not affect performance since ideally the timeout never
occurs.
Fixes: 8f3631f0f6 ("serial/8250: Use fifo in 8250 console driver")
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Wander Lairson Costa <wander@redhat.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20250107212702.169493-2-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The use of of_property_read_bool() for non-boolean properties is
deprecated in favor of of_property_present() when testing for property
presence.
As of_property_present() returns a boolean, use that directly
and simplify the code a bit while we're here.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Acked-by: Richard Genoud <richard.genoud@bootlin.com>
Reviewed-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20250109182053.3970547-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fall back to polling mode if no interrupt is configured because there
is no possibility to connect the interrupt pin.
If "interrupts" property is missing in devicetree the driver
uses a delayed worker to pull the state of interrupt status registers.
Signed-off-by: Andre Werner <andre.werner@systec-electronic.com>
Link: https://lore.kernel.org/r/20250110073104.1029633-2-andre.werner@systec-electronic.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
LAN969x uses the Atmel serial, so make it selectable for ARCH_LAN969X.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20250108131045.40642-3-robert.marko@sartura.hr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The LKP robot complains about:
drivers/tty/mips_ejtag_fdc.c:1224:31: error: incompatible pointer types passing 'const char *[1]' to parameter of type 'const u8 **' (aka 'const unsigned char **')
Fix this by turning the missing pieces (fetch from kgdbfdc_wbuf) to u8
too. Note the filling part (kgdbfdc_write_char()) already receives and
stores u8 to kgdbfdc_wbuf.
Fixes: ce7cbd9a6c ("tty: mips_ejtag_fdc: use u8 for character pointers")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202501101327.oGdWbmuk-lkp@intel.com/
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250110115228.603980-1-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, code retries n2 times to open control dlci in ABM mode before
switching to ADM mode, but only if DM has been received. This contradicts
to the comment that dlci is switched to control mode unconditionally if
DLCI_OPENING retries time out. Also, it does not make sense to continue
trying once DM has received.
Change the logic to switch to ADM mode upon DM received. That way control
channel state will change to DLCI_OPEN way faster. Fix the misleading
comment while at it.
Signed-off-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20241228150100.100354-3-ivo.g.dimitrov.75@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently code does not wait for channel 0 open sequence to complete before
pushing data to the other channels. Also, if userland opens tty, it will
receive EL2NSYNC. Both issues result in hard to predict initialization
sequence and possible userland failures.
Fix that by waiting channel 0 open sequence to complete before attempting
opening of the other channels. Also, if tty open() is attempted while
channel 0 is opening, wait until sequence is complete before returning to
userland.
Signed-off-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20241228150100.100354-2-ivo.g.dimitrov.75@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Need to flush UART RX and TX FIFO when lpuart is shutting down to make
sure restore a clean data transfer environment.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20250107074834.3115230-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some SoCs like the i.MX943 have aliases for up to 12 UARTs, need to
increase UART_NR from 8 to 12 to support lpuart9-12 to avoid
initialization failures.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20250103071154.3070924-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Constify the following API:
struct device *device_find_child(struct device *dev, void *data,
int (*match)(struct device *dev, void *data));
To :
struct device *device_find_child(struct device *dev, const void *data,
device_match_t match);
typedef int (*device_match_t)(struct device *dev, const void *data);
with the following reasons:
- Protect caller's match data @*data which is for comparison and lookup
and the API does not actually need to modify @*data.
- Make the API's parameters (@match)() and @data have the same type as
all of other device finding APIs (bus|class|driver)_find_device().
- All kinds of existing device match functions can be directly taken
as the API's argument, they were exported by driver core.
Constify the API and adapt for various existing usages.
BTW, various subsystem changes are squashed into this commit to meet
'git bisect' requirement, and this commit has the minimal and simplest
changes to complement squashing shortcoming, and that may bring extra
code improvement.
Reviewed-by: Alison Schofield <alison.schofield@intel.com>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Uwe Kleine-König <ukleinek@kernel.org> # for drivers/pwm
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20241224-const_dfc_done-v5-4-6623037414d4@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Data loss on serial line was observed during communication through
serial ports ttyAMA1 and ttyAMA2 interconnected via RS485 transcievers.
Both ports are in one BCM2711 (Compute Module CM40) and they share
the same interrupt line.
The problem is caused by long waiting for tx queue flush in the function
pl011_rs485_tx_stop. Udelay or mdelay are used to wait.
The function is called from the interrupt handler. If multiple devices
share a single interrupt line, late processing of pending interrupts
and data loss may occur. When operation of both devices are synchronous,
collisions are quite often.
This rework is based on the method used in tty/serial/imx.c
Use hrtimer instead of udelay and mdelay calls.
Replace simple bool variable rs485_tx_started by 4-state variable
rs485_tx_state.
Tested-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Signed-off-by: Miroslav Ondra <ondra@faster.cz>
Link: https://lore.kernel.org/r/20241221-amba-rts-v3-1-d3d444681419@faster.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 30e945861f ("serial: stm32: add support for break control")
added another usage of the port lock, but was merged on the same day as
c5d0666255 ("serial: stm32: Use port lock wrappers"), therefore the
latter did not update this usage to use the port lock wrappers.
Fixes: c5d0666255 ("serial: stm32: Use port lock wrappers")
Cc: stable <stable@kernel.org>
Signed-off-by: Ben Wolsieffer <ben.wolsieffer@hefring.com>
Reviewed-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20241216145323.111612-1-ben.wolsieffer@hefring.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When executing 'echo mem > /sys/power/state', the following
deadlock occurs. Since there is output during the serial
port entering the suspend process, the suspend will be
interrupted, resulting in the nesting of locks. Therefore,
use uart_port_lock_irq() instead of uart_port_unlock().
WARNING: inconsistent lock state
6.12.0-rc2-00002-g3c199ed5bd64-dirty #23 Not tainted
--------------------------------
inconsistent {IN-HARDIRQ-W} -> {HARDIRQ-ON-W} usage.
sh/494 [HC0[0]:SC0[0]:HE1:SE1] takes:
c4db5850 (&port_lock_key){?.-.}-{3:3}, at: imx_uart_enable_wakeup+0x14/0x254
{IN-HARDIRQ-W} state was registered at:
lock_acquire+0x104/0x348
_raw_spin_lock+0x48/0x84
imx_uart_int+0x14/0x4dc
__handle_irq_event_percpu+0xac/0x2fc
handle_irq_event_percpu+0xc/0x40
handle_irq_event+0x38/0x8c
handle_fasteoi_irq+0xb4/0x1b8
handle_irq_desc+0x1c/0x2c
gic_handle_irq+0x6c/0xa0
generic_handle_arch_irq+0x2c/0x64
call_with_stack+0x18/0x20
__irq_svc+0x9c/0xbc
_raw_spin_unlock_irqrestore+0x2c/0x48
uart_write+0xd8/0x3a0
do_output_char+0x1a8/0x1e4
n_tty_write+0x224/0x440
file_tty_write.constprop.0+0x124/0x250
do_iter_readv_writev+0x100/0x1e0
vfs_writev+0xc4/0x448
do_writev+0x68/0xf8
ret_fast_syscall+0x0/0x1c
irq event stamp: 31593
hardirqs last enabled at (31593): [<c1150e48>] _raw_spin_unlock_irqrestore+0x44/0x48
hardirqs last disabled at (31592): [<c07f32f0>] clk_enable_lock+0x60/0x120
softirqs last enabled at (30334): [<c012d1d4>] handle_softirqs+0x2cc/0x478
softirqs last disabled at (30325): [<c012d510>] __irq_exit_rcu+0x120/0x15c
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&port_lock_key);
<Interrupt>
lock(&port_lock_key);
Fixes: 3c199ed5bd ("serial: imx: Grab port lock in imx_uart_enable_wakeup()")
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20241210233613.2881264-1-xiaolei.wang@windriver.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit f9b11229b7 ("serial: 8250: Fix PM usage_count for console
handover") fixed one runtime PM usage counter balance problem that
occurs because .dev is not set during univ8250 setup preventing call to
pm_runtime_get_sync(). Later, univ8250_console_exit() will trigger the
runtime PM usage counter underflow as .dev is already set at that time.
Call pm_runtime_get_sync() to balance the RPM usage counter also in
serial8250_register_8250_port() before trying to add the port.
Reported-by: Borislav Petkov (AMD) <bp@alien8.de>
Fixes: bedb404e91 ("serial: 8250_port: Don't use power management for kernel console")
Cc: stable <stable@kernel.org>
Tested-by: Borislav Petkov (AMD) <bp@alien8.de>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20241210170120.2231-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The role of @read_status_mask has changed over time and seems
to still cause confusion. This can be expected since there is
zero documentation about this driver-specific variable.
Add comments to the initialization of @read_status_mask to
clarify its role.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20241216171244.12783-5-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
