This reverts commit d922b54e94, reversing
changes made to 3f0245e23a.
The SH maintainer has indicated that he want to carry these changes
in the SH tree instead, and need more time to review and merge the
changes, so reverting it out from my tree.
Signed-off-by: Linus Walleij <linusw@kernel.org>
- Embed pins in the priv struct on RZ/A2.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCalihdAAKCRCKwlD9ZEnx
cOkyAQCyUWsVjxjqQydNOe/0UxRs62GLwUcvuUzrpyxzKd0/3wEAlAEH1IGx+Slh
QGrD9tThiWZKUn9bb3V4JHhajL34YAw=
=+DCW
-----END PGP SIGNATURE-----
Merge tag 'renesas-pinctrl-for-v7.3-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: renesas: Updates for v7.3
- Embed pins in the priv struct on RZ/A2.
Signed-off-by: Linus Walleij <linusw@kernel.org>
This patch extends the sh-pfc GPIO driver to support software-node-based
configuration for the secondary 'function' GPIO chip.
While the primary GPIO chip typically uses the firmware node attached to
the parent platform device, the secondary chip should target a specific
child node to avoid ambiguity when defining GPIO hogs or properties.
Update gpio_function_setup() to look for a child node named 'functions',
but only when the parent is a software node. This ensures the behavior
is restricted to legacy platforms being migrated to software nodes.
Assisted-by: Gemini:gemini-3.1-pro
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Reviewed-by: Linus Walleij <linusw@kernel.org>
Signed-off-by: Linus Walleij <linusw@kernel.org>
The sh-pfc driver registers two separate gpiochip instances: one for
real GPIOs and another for function GPIOs. Since both share the same
parent platform device, gpiolib's fallback logic causes both chips to
share the same firmware node (fwnode).
This causes ambiguity when using software nodes to describe GPIOs, as
gpiolib may apply hogs meant for one chip to the other if they share the
same node.
Explicitly set gc->fwnode to ERR_PTR(-ENODEV) for the function GPIO
chip. This satisfies gpiolib's check for an existing fwnode and prevents
it from falling back to the parent device's node, while ensuring that no
actual properties or hogs are found on the function chip unless
explicitly assigned later.
Assisted-by: Gemini:gemini-3.1-pro
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Reviewed-by: Linus Walleij <linusw@kernel.org>
Signed-off-by: Linus Walleij <linusw@kernel.org>
Turn the separately allocated pinctrl_pin_desc array into a flexible
array member of struct rza2_pinctrl_priv, annotated with
__counted_by(npins). Compute the pin count before allocation so
struct_size() can size the combined object, and the two allocations can
be collapsed into one.
Change npins to unsigned int to avoid potential overflow/underflow
errors.
Assisted-by: Claude:Opus-4.7
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260527202317.5347-1-rosenp@gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
- Fix locking on RZ/G3L.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCaiaEHgAKCRCKwlD9ZEnx
cAcGAQDyFA1YJqpoXSgzjv0Kp0hG2MvaDXdx4rhCC5yjYesIdAEAvgcBMqbQqKct
ZAM2E2gd+GmdsdReRpmMWqnzp3LnDAk=
=sLxt
-----END PGP SIGNATURE-----
Merge tag 'renesas-pinctrl-for-v7.2-tag3' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: renesas: Updates for v7.2 (take three)
- Fix locking on RZ/G3L.
* tag 'renesas-pinctrl-for-v7.2-tag3' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers:
pinctrl: renesas: rzg2l: Use raw_spinlock_irqsave() on power source update
Signed-off-by: Linus Walleij <linusw@kernel.org>
The rest of the driver uses raw_spin_lock_irqsave() and
raw_spin_unlock_irqrestore() for locking. To avoid concurrency issues
or deadlocks, use raw_spinlock_irqsave() via the scoped_guard() helper
for power source updates as well.
Fixes: bbe2277ded ("pinctrl: renesas: rzg2l: Add support for selecting power source for {WDT,AWO,ISO}")
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260603151642.4075678-2-claudiu.beznea@kernel.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Named initializers are better readable and more robust to changes of the
struct definition. This robustness is relevant for a planned change to
struct platform_device_id replacing .driver_data by an anonymous unit.
While touching these arrays unify spacing and usage of commas.
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> # renesas
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be> # renesas
Signed-off-by: Linus Walleij <linusw@kernel.org>
Use tab instead of spaces to follow the same coding style.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://patch.msgid.link/20260528080439.615958-5-claudiu.beznea@kernel.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Keep the documentation for struct rzg2l_pinctrl_reg_cache members aligned
with the struct member order.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://patch.msgid.link/20260528080439.615958-4-claudiu.beznea@kernel.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The pinctrl and GPIO core code make exceptions for the -ENOTSUPP error
code. One such example is gpio_set_config_with_argument_optional(), which
returns success when gpio_set_config_with_argument() returns -ENOTSUPP, but
reports failure for all other error codes.
Returning -EOPNOTSUPP from the pinctrl driver on the unsupported pinctrl
operation may lead to boot failures when pinctrl drivers implements
struct gpio_chip::set_config, the system uses GPIO hogs, and the
struct gpio_chip::set_config implementation returns -EOPNOTSUPP for the
unsupported operations.
Currently, the driver does not implement struct gpio_chip::set_config().
To avoid future failures, return -ENOTSUPP from
rzv2m_pinctrl_pinconf_set().
rzv2m_pinctrl_pinconf_group_get() is used when dumping pinctrl
configuration. pinconf_generic_dump_one(), which calls it, makes
exceptions for the -EINVAL and -ENOTSUPP error codes. The documentation
for struct pinconf_ops::pin_config_group_get states that it "should
return -ENOTSUPP and -EINVAL using the same rules as pin_config_get()".
The documentation for struct pinconf_ops::pin_config_get states:
"get the config of a certain pin, if the requested config is not available
on this controller this should return -ENOTSUPP and if it is available but
disabled it should return -EINVAL".
Return -ENOTSUPP for the unsupported pinctrl operation.
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260522105717.1727837-1-claudiu.beznea@kernel.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The pinctrl and GPIO core code make exceptions for the -ENOTSUPP error
code. One such example is gpio_set_config_with_argument_optional(),
which returns success when gpio_set_config_with_argument() returns
-ENOTSUPP, but reports failure for all other error codes.
Returning -EOPNOTSUPP from the pinctrl driver on the unsupported pinctrl
operation may lead to boot failures when pinctrl drivers implements
struct gpio_chip::set_config, the system uses GPIO hogs, and the
struct gpio_chip::set_config implementation returns -EOPNOTSUPP for the
unsupported operations.
Return -ENOTSUPP for the unsupported pinctrl operation.
Fixes: 560c633d37 ("pinctrl: renesas: rzg2l: Drop oen_read and oen_write callbacks")
Fixes: c4c4637eb5 ("pinctrl: renesas: Add RZ/G2L pin and gpio controller driver")
Cc: stable@vger.kernel.org
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260515124008.2947838-2-claudiu.beznea@kernel.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
In rzt2h_pinctrl_set_pfc_mode(), read the PMC and PFC registers upfront
and skip the pin function configuration if the pin is already in
peripheral mode with the desired function.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260513115312.1574367-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Variable 'j' in rzt2h_pinctrl_register() is incremented during pin
descriptor initialization but never used afterwards.
Remove the unused variable and the associated dead code.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260513115312.1574367-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
When reading /sys/kernel/debug/pinctrl/*.pinctrl-sh-pfc/pinconf-groups
while CONFIG_DEBUG_PINCTRL is enabled, the user is confronted with a
seemlingly endless stream of identical messages on the console:
sh-pfc e6060000.pinctrl: cannot get configuration for pin group, missing group config get function in driver
Fix this by implementing the sh_pfc_pinconf_ops.pin_config_group_get()
callback.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/130ce567f23fd6eef8f5fa7273480a0e3ff2d1d9.1777562482.git.geert+renesas@glider.be
The RZ/G3L SoC has some IP such as I2C ch{2,3},SCIF ch{3,4,5},
RSPI ch{1,2} and RSCI ch{1,2,3} need to control the clone channel for
proper operation. As per the RZ/G3L hardware manual, the clone channel
setting is to be done before the mux setting.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260430093422.74812-8-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The port and function selectors are evaluated multiple times
in rzg2l_pinctrl_set_mux(). Simplify the function by dropping
dupicate evaluation storing them in local variables.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260430093422.74812-7-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The RZ/G2L SoC uses pin 0 from a port for OEN while RZ/G3L uses pin 1. The
existing greater-than comparison against oen_max_pin in
rzg2l_pin_to_oen_bit() would incorrectly accept any pin below that value
rather than enforcing the single valid OEN pin for each SoC. Replace the
range check with an exact equality test so that only the designated OEN
pin is accepted.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260430093422.74812-5-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The RZ/G3L SoC has support for setting power source that are not
controlled by the following voltage control registers:
- SD_CH{0,1,2}_POC, XSPI_POC, ETH{0,1}_POC, I3C_SET.POC
Add support for selecting voltages using OTHER_POC register for
setting I/O domain voltage for WDT, ISO and AWO by extending
rzg2l_caps_to_pwr_reg() with a mask output parameter so that callers
callers can identify which bit(s) within OTHER_POC correspond to the
requested domain. Update rzg2l_get_power_source() to extract the
relevant bit field via field_get() when reading OTHER_POC, and update
rzg2l_set_power_source() to perform a read-modify-write under the
spinlock when writing to OTHER_POC, since multiple domains share the
same register.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260430093422.74812-4-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The QSPI register at offset 0x3008 is not present on all SoCs supported by
the RZ/G2L pinctrl driver. Unconditionally reading and writing this
register during suspend/resume on hardware that lacks it can cause
undefined behaviour.
Add a qspi field to rzg2l_register_offsets to allow per-SoC declaration of
the QSPI register offset, and guard the suspend/resume accesses with a
check on that field. Populate the offset only for the RZ/{G2L,G2LC,G2UL,
Five} hardware configuration, which is where the register is known to
exist.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260430093422.74812-3-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Include PIN_CFG_IOLH_RZV2H in the IOLH capability checks when saving
and restoring pin configuration registers.
On RZ/V2H(P), RZ/V2N, and RZ/G3E, the IOLH configuration is defined by
the PIN_CFG_IOLH_RZV2H capability. The previous implementation did not
account for this, causing the IOLH registers to be skipped during PM
save/restore.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260413182456.811543-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Store SMT register cache per bank instead of using a single array.
On RZ/V2H(P), RZ/V2N, and RZ/G3E, the SMT register is split across two
32-bit registers: bits 0/8/16/24 control pins 0-3, while pins 4-7 are
controlled by the corresponding bits in the next register. The previous
implementation cached only a single SMT register, leading to incomplete
save/restore of SMT state.
Convert cache->smt to a per-bank array and allocate storage for both
halves. Update suspend/resume handling to save and restore both SMT
registers when present.
Fixes: 837afa592c ("pinctrl: renesas: rzg2l: Add suspend/resume support for Schmitt control registers")
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260413182456.811543-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
When saving/restoring pull-up/down register state during suspend/resume,
the second PUPD register access was incorrectly using the same base offset
as the first, effectively reading/writing the same register twice instead
of the adjacent one.
Add the correct + 4 byte offset to the second RZG2L_PCTRL_REG_ACCESS32
call so that pupd[1][port] is properly saved and restored from the next
32-bit register in the PUPD register pair, covering pins 4–7 of ports
with 4 or more pins.
Fixes: b2bd65fbb6 ("pinctrl: renesas: rzg2l: Add suspend/resume support for pull up/down")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260328090548.84124-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The rzg2l_pinctrl_pm_setup_regs() handles save/restore of
{IOLH,IEN,PUPD,SMT} registers during s2ram, but only for ports where all
pins share the same pincfg. Extend the code to also support ports with
variable pincfg per pin, so that {IOLH,IEN,PUPD,SMT} registers are
correctly saved and restored for all pins.
Fixes: 254203f9a9 ("pinctrl: renesas: rzg2l: Add suspend/resume support")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260326162459.101414-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add pin configuration support for the Renesas RZ/T2H SoC. The RZ/T2H SoC
allows configuring several electrical characteristics through the DRCTLm
(I/O Buffer Function Switching) registers. These registers control bias
configuration, Schmitt trigger input, output slew rate, and drive
strength.
Implement pinconf_ops to allow reading and updating these properties
through the generic pin configuration framework. The implementation
supports bias-disable, bias-pull-up, bias-pull-down,
input-schmitt-enable, slew-rate, and drive-strength-microamp.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Linus Walleij <linusw@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260319141515.2053556-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The GPIO .get() callback is expected to return 0 or 1 (or a negative
error code). Ensure that the value returned by rza1_gpio_get() is
normalized to the [0, 1] range.
Fixes: 86ef402d80 ("gpiolib: sanitize the return value of gpio_chip::get()")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Reviewed-by: Linus Walleij <linusw@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/aZYnyl-Nf4S1U2yj@google.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The rzt2h_gpio_get_direction() function is called from
gpiod_get_direction(), which ends up being used within the __setup_irq()
call stack when requesting an interrupt.
__setup_irq() holds a raw_spinlock_t with IRQs disabled, which creates
an atomic context. spinlock_t cannot be used within atomic context
when PREEMPT_RT is enabled, since it may become a sleeping lock.
An "[ BUG: Invalid wait context ]" splat is observed when running with
CONFIG_PROVE_LOCKING enabled, describing exactly the aforementioned call
stack.
__setup_irq() needs to hold a raw_spinlock_t with IRQs disabled to
serialize access against a concurrent hard interrupt.
Switch to raw_spinlock_t to fix this.
Fixes: 829dde3369 ("pinctrl: renesas: rzt2h: Add GPIO IRQ chip to handle interrupts")
Signed-off-by: Cosmin Tanislav <cosmin-gabriel.tanislav.xa@renesas.com>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260205103930.666051-1-cosmin-gabriel.tanislav.xa@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
When calling of_parse_phandle_with_fixed_args(), the caller is
responsible for calling of_node_put() to release the device node
reference.
In rzt2h_gpio_register(), the driver fails to call of_node_put() to
release the reference in of_args.np, which causes a memory leak.
Add the missing of_node_put() call to fix the leak.
Fixes: 34d4d09307 ("pinctrl: renesas: Add support for RZ/T2H")
Signed-off-by: Felix Gu <ustc.gu@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260127-rzt2h-v1-1-86472e7421b8@gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This was done entirely with mindless brute force, using
git grep -l '\<k[vmz]*alloc_objs*(.*, GFP_KERNEL)' |
xargs sed -i 's/\(alloc_objs*(.*\), GFP_KERNEL)/\1)/'
to convert the new alloc_obj() users that had a simple GFP_KERNEL
argument to just drop that argument.
Note that due to the extreme simplicity of the scripting, any slightly
more complex cases spread over multiple lines would not be triggered:
they definitely exist, but this covers the vast bulk of the cases, and
the resulting diff is also then easier to check automatically.
For the same reason the 'flex' versions will be done as a separate
conversion.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the result of running the Coccinelle script from
scripts/coccinelle/api/kmalloc_objs.cocci. The script is designed to
avoid scalar types (which need careful case-by-case checking), and
instead replace kmalloc-family calls that allocate struct or union
object instances:
Single allocations: kmalloc(sizeof(TYPE), ...)
are replaced with: kmalloc_obj(TYPE, ...)
Array allocations: kmalloc_array(COUNT, sizeof(TYPE), ...)
are replaced with: kmalloc_objs(TYPE, COUNT, ...)
Flex array allocations: kmalloc(struct_size(PTR, FAM, COUNT), ...)
are replaced with: kmalloc_flex(*PTR, FAM, COUNT, ...)
(where TYPE may also be *VAR)
The resulting allocations no longer return "void *", instead returning
"TYPE *".
Signed-off-by: Kees Cook <kees@kernel.org>
The Renesas RZ/T2H (R9A09G077) and Renesas RZ/N2H (R9A09G087) SoCs have
IRQ-capable pins handled by the ICU, which forwards them to the GIC.
The ICU supports 16 IRQ lines, the pins map to these lines arbitrarily,
and the mapping is not configurable.
Add a GPIO IRQ chip to the pin controller that can be used to configure
these pins as IRQ lines.
The pin controller places the requested pins into IRQ function,
disabling GPIO mode. A hierarchical IRQ domain is used to forward other
functionality to the parent IRQ domain, the ICU. The ICU does level
translation and then forwards other functionality to the GIC.
Wakeup capability is implemented by placing the entire pin controller on
the wakeup path if any pins are requested to be wakeup-capable.
Signed-off-by: Cosmin Tanislav <cosmin-gabriel.tanislav.xa@renesas.com>
Reviewed-by: Linus Walleij <linusw@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260109143910.645628-2-cosmin-gabriel.tanislav.xa@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Setting up an IRQ would normally be done in the .activate() and
.deactivate() ops of the IRQ domain, but for hierarchical IRQ domains
the .activate() and .deactivate() ops are overridden in the
gpiochip_hierarchy_setup_domain_ops() function.
As such, activating and deactivating need to be done in the .translate()
and .free() ops of the IRQ domain.
For RZ/T2H and RZ/N2H, interrupts go through the pin controller, into
the ICU, which level-translates them and forwards them to the GIC.
To use a GPIO as an interrupt it needs to be put into peripheral
function mode 0, which will connect it to the IRQ lines of the ICU.
The IRQ chip .child_to_parent_hwirq() callback is called as part of the
IRQ fwspec parsing logic (as part of irq_create_of_mapping()) which
happens before the IRQ is requested (as part of gpiochip_lock_as_irq()).
gpiochip_lock_as_irq() calls gpiod_get_direction() if the
.get_direction() callback is provided to ensure that the GPIO line is
set up as input.
In our case, IRQ function is separate from GPIO, and both cannot be true
at the same time.
Return GPIO_LINE_DIRECTION_IN even if pin is in IRQ function to allow
this setup to work.
Hold the spinlock to ensure atomicity between reading the PMC register
(which determines whether the pin is in GPIO mode or not) and reading
the function of the pin when it is not in GPIO mode.
Signed-off-by: Cosmin Tanislav <cosmin-gabriel.tanislav.xa@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251205150234.2958140-3-cosmin-gabriel.tanislav.xa@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
GPIO is enabled or disabled in multiple places, simplify code by moving
this logic into a separate function.
Signed-off-by: Cosmin Tanislav <cosmin-gabriel.tanislav.xa@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251205150234.2958140-2-cosmin-gabriel.tanislav.xa@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Extract the OEN register write with PWPR protection logic into a helper
function to eliminate code duplication between rzg2l_write_oen() and
rzg2l_pinctrl_resume_noirq().
Introduce rzg2l_oen_write_with_pwpr() helper that encapsulates the
PWPR unlock, OEN register write, and PWPR lock sequence. This helper
must be called with pctrl->lock already held by the caller.
Reported-by: Pavel Machek <pavel@denx.de>
Closes: https://lore.kernel.org/cip-dev/OS9PR01MB16368C765305362F5F4132759FFC4A@OS9PR01MB16368.jpnprd01.prod.outlook.com/T/#u
Signed-off-by: John Madieu <john.madieu.xa@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251106080758.36645-1-john.madieu.xa@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Rev.0.81 of the R-Car V4M Series Hardware User’s Manual removed the
"STPWT_EXTFXR" signal from the pin control register tables. As this is
further unused in the pin control driver, it can be removed safely.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Link: https://patch.msgid.link/f849fa3b9b516e9dd04b45462b69f52225259480.1762274384.git.geert+renesas@glider.be
Rev.0.71 of the R-Car V4M Series Hardware User’s Manual removed the
"CC5_OSCOUT" signal from the pin control register tables. As this is
further unused in the pin control driver, it can be removed safely.
Signed-off-by: Huy Bui <huy.bui.wm@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Link: https://patch.msgid.link/895bb560467309706931d14aeea0e063ad0e86eb.1762274384.git.geert+renesas@glider.be
Rev.1.30 of the R-Car V4H Series Hardware User’s Manual removed the
"STPWT_EXTFXR" signal from the pin control register tables. As this is
further unused in the pin control driver, it can be removed safely.
Signed-off-by: Huy Bui <huy.bui.wm@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Link: https://patch.msgid.link/f6cfdbbc024d85e87583a1d57ea01582632f1216.1762274384.git.geert+renesas@glider.be
Rev.1.30 of the R-Car V4H Series Hardware User’s Manual removed the
"CC5_OSCOUT" signal from the pin control register tables. As this is
further unused in the pin control driver, it can be removed safely.
Signed-off-by: Huy Bui <huy.bui.wm@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Link: https://patch.msgid.link/77f9efe5388f2801ace945b7793d4823618eeec8.1762274384.git.geert+renesas@glider.be
Rev.1.30 of the R-Car V4H Series Hardware User’s Manual removed the
"AVB[01]_MII_*" signals from the pin control register tables. As these
are further unused in the pin control driver, they can be removed
safely.
Signed-off-by: Thanh Quan <thanh.quan.xn@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Link: https://patch.msgid.link/58662f50136280532bcc8bbe94741d82425bd118.1762274384.git.geert+renesas@glider.be
rzg2l_gpio_irq_set_type() and rzg2l_gpio_irqc_eoi() only call the
equivalent parent functions, replace their usage with the parent
functions and remove them.
Signed-off-by: Cosmin Tanislav <cosmin-gabriel.tanislav.xa@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251022074100.1994447-1-cosmin-gabriel.tanislav.xa@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
