DSI 6G v2.9 hosts (SM8650, SM8750, Kaanapali, etc.) reparent the byte and
pixel RCGs to the DSI PHY PLL at runtime from
dsi_link_clk_set_rate_6g_v2_9(), after the PHY has been enabled. However
dsi_calc_clk_rate_6g() runs earlier, in order to compute the bit clock
request for the PHY. At that point the byte RCG still has its reset
parent (XO), so clk_round_rate() returns a bogus rate, which then ends up
in the PHY bit clock request and the PLL gets programmed to a wrong
frequency, breaking the panel.
Move the rounding to dsi_link_clk_set_rate_6g(), which is called after
the RCGs have been reparented to the PLL. Storing the rounded rate at
this point still makes later link_clk_set_rate() calls no-ops in the
CCF. Derive the byte interface clock rate from the rounded byte clock
rate, otherwise it would keep requesting the idealized rate and
retrigger the PLL on every transfer.
Reported-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Reported-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Fixes: 6cd33b6f41 ("drm/msm/dsi: round 6G byte clock rate to the PLL-achievable value")
Assisted-by: LLM
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Tested-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> # SM6115P J606F
Tested-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Reviewed-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/750496/
Link: https://lore.kernel.org/r/20260903-fix-eliza-dsi-v1-1-3474a6c9f2e0@oss.qualcomm.com
dev_pm_opp_set_rate(0) removes the vote specified in required-opps but
does not actually park the clock, making it run without the necessary
power backing. Drop the explicit call to it.
Every call site of ops->link_clk_disable() is followed by
pm_runtime_put(), so the power vote will be rescinded if deemed safe.
Fixes: 32d3e0fecc ("drm/msm: dsi: Use OPP API to set clk/perf state")
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/742783/
Link: https://lore.kernel.org/r/20260728-topic-dpu_power-v1-3-e7783b859a70@oss.qualcomm.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
MSM8916 runtime DSI commands still go through
msm_dsi_host_xfer_prepare(), which re-applies the link clock rate before
enabling the link clocks. That is fine in principle, but on DSI 6G the
requested byte clock rate often does not exactly match the DSI PHY PLL's
realizable rate. For example, the driver can request 56250000 Hz while the
PLL actually runs at 56246337 Hz.
Because the requested and actual rates differ slightly, every later
link_clk_set_rate() call is treated as a real clock change and re-locks
the PLL. On a video-mode panel without an internal timing generator, such
as samsung,s6d7aa0 / lsl080al03 on MSM8916, that live-clock glitch makes
the panel lose pixel lock and visibly corrupts scanout on each runtime DCS
command, including backlight writes.
Fix this by rounding the computed 6G byte clock rate up front, before it is
stored in msm_host->byte_clk_rate and reused by later transfers. Once the
host carries the PLL-achievable rate instead of the idealized one,
repeated link_clk_set_rate() calls become no-ops in the common clock
framework and no longer re-lock the PLL.
This keeps the normal transfer callback sequencing intact, preserves the
OPP vote path in link_clk_set_rate(), and matches the fix direction
suggested in the original 2018 discussion.
Reported-by: Daniel Mack <daniel@zonque.org>
Closes: https://lore.kernel.org/all/1a682c5b-7fc9-3aaa-120b-64b239a355a3@zonque.org/
Fixes: 6b16f05aa3 ("drm/msm/dsi: Split clk rate setting and enable")
Cc: stable@vger.kernel.org
Signed-off-by: Kavan Smith <kavansmith82@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/738234/
Link: https://lore.kernel.org/r/20260707013240.681012-1-kavansmith82@gmail.com
[DB: dropped extra chunk from the patch]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Some panels support multiple slice to be sent in a single DSC packet and
this feature is a must for specific panels, such as the JDI LPM026M648C.
Use the MIPI_DSI_MODE_DSC_ALL_SLICES_IN_PKT flag to derive slice_per_pkt
from slice_count, note that most panels are expected to just work with
just one slice per packet.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Alexander Koskovich <akoskovich@pm.me>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Tested-by: Junjie Cao <junjie.cao@linux.dev>
Acked-by: Maxime Ripard <mripard@kernel.org> # from v1
Link: https://patch.msgid.link/20260318-dsi-dsc-slice-per-pkt-v2-2-0a1b316f8250@pm.me
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Changes for v7.2
Core:
- Fixed documentation for msm_gem_shrinker functions
- IFPC related enablement/fixes for gen8
- PERFCNTR_CONFIG ioctl support
GPU
- Reworked handling of UBWC configuration
- a810 suppport
MDSS:
- Added Milos platform support
- Reworked handling of UBWC configuration
DisplayPort:
- Reworked HPD handling, preparing for the MST support
DPU:
- Added Milos platform support
- Reworked handling of UBWC configuration
DSI:
- Added Milos platform support
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <rob.clark@oss.qualcomm.com>
Link: https://patch.msgid.link/CACSVV00DXZcvFH2-C3fouve5DGs0DGa-vvsJPuaRmUZZVNKOfg@mail.gmail.com
-----BEGIN PGP SIGNATURE-----
iQFSBAABCgA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmoTZAYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGKZ0H/A8Ti79DXqEl4M6V
S1ZYfteuvyWCdygPfY7+CQsxS1EjfmeRXd0213n95jijUoXvAVe7HJ5FuroTltsF
LYqH3CAedeEWMO1rIZjuDs5J1BzWAh7b0/QoanTlAjI1ZL8c3Btj/o//PoQfztiS
HWlN/aCcsZTi9n0ewV9eQM9jdiuhBlpZujfDX90vYurxAB+3K2c1b0UN+Y4/zMXO
83zaDLMYhIh8cEaU52+23H9UpyfrT0B8n6YgqbU4ZBRIbgA1BC4gloT6B7OHFKfq
PAfjAOBfpe43K8lLUyfbkfNohNblLOboiMmekdf+j2y4wqpCO64o6WigCrZtxtHe
9znkJpM=
=H+I9
-----END PGP SIGNATURE-----
Merge v7.1-rc5 into drm-next
Boris Brezillion needs the gem lru fixes 379e8f1ca5 ("drm/gem: Make
the GEM LRU lock part of drm_device") backmerged for drm-misc-next.
That also means we need to sort out the rename conflict in panthor with
the fixup patch from Boris from drm-tip.
Signed-off-by: Simona Vetter <simona.vetter@ffwll.ch>
On DSI 6G platforms the IO address space is internally adjusted by
io_offset. Later this adjusted address might be used for memory dumping.
However the size that is used for memory dumping isn't adjusted to
account for the io_offset, leading to the potential access to the
unmapped region. Lower ctrl_size by the io_offset value to prevent
access past the mapped area.
msm_disp_snapshot_add_block+0x1d4/0x3c8 [msm] (P)
msm_dsi_host_snapshot+0x4c/0x78 [msm]
msm_dsi_snapshot+0x28/0x50 [msm]
msm_disp_snapshot_capture_state+0x74/0x140 [msm]
msm_disp_snapshot_state_sync+0x60/0x90 [msm]
_msm_disp_snapshot_work+0x30/0x90 [msm]
kthread_worker_fn+0xdc/0x460
kthread+0x120/0x140
Fixes: bac2c6a62e ("drm/msm: get rid of msm_iomap_size")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/721747/
Link: https://lore.kernel.org/r/20260428-msm-fix-dsi-dump-v1-1-5d4cb5ccfac7@oss.qualcomm.com
Add video and command mode destination format mappings for RGB101010,
and extend the VID_CFG0 DST_FORMAT bitfield to 3 bits to accommodate
the new format value.
Make sure this is guarded behind MSM_DSI_6G_VER >= V2.1.0 as anything
older does not support this.
Required for 10 bit panels such as the BOE BF068MWM-TD0 found on the
Nothing Phone (3a).
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Alexander Koskovich <akoskovich@pm.me>
Patchwork: https://patchwork.freedesktop.org/patch/713721/
Link: https://lore.kernel.org/r/20260324-dsi-rgb101010-support-v5-5-ff6afc904115@pm.me
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Add a helper for checking if the DSI hardware version is greater
than or equal to a given version, for use in a future change.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Alexander Koskovich <akoskovich@pm.me>
Patchwork: https://patchwork.freedesktop.org/patch/713719/
Link: https://lore.kernel.org/r/20260324-dsi-rgb101010-support-v5-4-ff6afc904115@pm.me
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
The MSM8998 DSI controller is v2.0.0 as stated in commit 7b8c9e2030
("drm/msm/dsi: Add support for MSM8998 DSI controller"). The value was
always correct just the name was wrong.
Rename and reorder to maintain version sorting.
Fixes: 7b8c9e2030 ("drm/msm/dsi: Add support for MSM8998 DSI controller")
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Alexander Koskovich <akoskovich@pm.me>
Patchwork: https://patchwork.freedesktop.org/patch/713717/
Link: https://lore.kernel.org/r/20260324-dsi-rgb101010-support-v5-3-ff6afc904115@pm.me
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
mipi_dsi_pixel_format_to_bpp return dst bpp not src bpp, dst bpp may
not be the uncompressed data size. use src bpc * 3 to get src bpp,
this aligns with pclk rate calculation.
Fixes: ac47870fd7 ("drm/msm/dsi: fix hdisplay calculation when programming dsi registers")
Signed-off-by: Pengyu Luo <mitltlatltl@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/709916/
Link: https://lore.kernel.org/r/20260307111250.105772-1-mitltlatltl@gmail.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
The drm/msm module bundles several drivers, each of them having a
separate OF match table, however only MDSS (subsystem), KMS devices and
GPU have corresponding MODULE_DEVICE_ID tables.
Add MODULE_DEVICE_ID to the display-related driver and to all other
drivers in this module, simplifying userspace job.
Fixes: 060530f1ea ("drm/msm: use componentised device support")
Reported-by: Loïc Minier <loic.minier@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/707960/
Link: https://lore.kernel.org/r/20260228-msm-device-id-v2-1-24b085919444@oss.qualcomm.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
The quirk flag DSI_PHY_7NM_QUIRK_PRE_V4_1 is renamed to
DSI_PHY_7NM_QUIRK_V4_0 to better reflect the actual hardware revision
it applies to. (Only SM8150 uses it, its hardware revision is 4.0)
No functional change.
Suggested-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Pengyu Luo <mitltlatltl@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/707416/
Link: https://lore.kernel.org/r/20260226122958.22555-3-mitltlatltl@gmail.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Recently, we round up new_hdisplay once at most, for bonded dsi, we
may need twice, since they are independent links, we should round up
each half separately. This also aligns with the hdisplay we program
later in dsi_timing_setup()
Example:
full_hdisplay = 1904, dsc_bpp = 8, bpc = 8
new_full_hdisplay = DIV_ROUND_UP(1904 * 8, 8 * 3) = 635
if we use half display
new_half_hdisplay = DIV_ROUND_UP(952 * 8, 8 * 3) = 318
new_full_display = 636
Fixes: 7c9e4a554d ("drm/msm/dsi: Reduce pclk rate for compression")
Signed-off-by: Pengyu Luo <mitltlatltl@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/709716/
Link: https://lore.kernel.org/r/20260306163255.215456-1-mitltlatltl@gmail.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
The hardware revision for TSMC 3nm-based Qualcomm SOCs should be 7.2,
this can be confirmed from REG_DSI_7nm_PHY_CMN_REVISION_ID0, the value
is 0x27, which means hardware revision is 7.2
No functional change.
Fixes: 1337d7ebfb ("drm/msm/dsi/phy: Add support for SM8750")
Suggested-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Pengyu Luo <mitltlatltl@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/707414/
Link: https://lore.kernel.org/r/20260226122958.22555-2-mitltlatltl@gmail.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Recently, the hdisplay calculation is working for 3:1 compressed ratio
only. If we have a video panel with DSC BPP = 8, and BPC = 10, we still
use the default bits_per_pclk = 24, then we get the wrong hdisplay. We
can draw the conclusion by cross-comparing the calculation with the
calculation in dsi_adjust_pclk_for_compression().
Since CMD mode does not use this, we can remove
!(msm_host->mode_flags & MIPI_DSI_MODE_VIDEO) safely.
Fixes: efcbd6f9cd ("drm/msm/dsi: Enable widebus for DSI")
Signed-off-by: Pengyu Luo <mitltlatltl@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/704822/
Link: https://lore.kernel.org/r/20260214105145.105308-1-mitltlatltl@gmail.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Add DSI PHY support for the Kaanapali platform, Kaanapali introduce
addition of DSI2/DSI2_phy compared to SM8650. However, based on the
HPG diagram, only DSI0_phy and DSI1_phy works.
Co-developed-by: Yongxing Mou <yongxing.mou@oss.qualcomm.com>
Signed-off-by: Yongxing Mou <yongxing.mou@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Yuanjie Yang <yuanjie.yang@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/698705/
Link: https://lore.kernel.org/r/20260115092749.533-7-yuanjie.yang@oss.qualcomm.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
The divider_round_rate() function is now deprecated, so let's migrate
to divider_determine_rate() instead so that this deprecated API can be
removed.
Note that when the main function itself was migrated to use
determine_rate, this was mistakenly converted to:
req->rate = divider_round_rate(...)
This is invalid in the case when an error occurs since it can set the
rate to a negative value.
Fixes: cc41f29a6b ("drm/msm/dsi_phy_14nm: convert from round_rate() to determine_rate()")
Signed-off-by: Brian Masney <bmasney@redhat.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/697613/
Link: https://lore.kernel.org/r/20260108-clk-divider-round-rate-v1-24-535a3ed73bf3@redhat.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
When in bonded DSI mode, only one PLL in one DSI PHY is used for both
DSI PHYs, meaning that parents of the secondary DSI PHY will use the
primary DSI PHY PLL as parent.
In this case the primary DSI PHY PLL will be set even if the primary
DSI PHY is not yet enabled. The DSI PHY code has support for this
particular use-case and will handle the fact the PLL was already
set when initializing the primary DSI PHY.
By introducing a protected variable pll_enable_cnt in the commit
cb55f39bf7 ("drm/msm/dsi/phy: Fix reading zero as PLL rates when unprepared"),
this variable is only initially set to 1 when the DSI PHY is initialized
making it impossible to set the PLL before, breaking the bonded DSI
use case by returning 0 when setting the PLL from the secondary DSI
PHY driver and skipping the correct clocks initialization.
But since it was already possible to set the PLL without enabling
the DSI PHY, just drop the pll_enable_cnt setting from the PHY
enable/disable and simply increment/decrement the pll_enable_cnt
variable from the dsi_pll_enable/disable_pll_bias to make sure any
PLL operation is done with the PLL BIAS enabled.
Fixes: cb55f39bf7 ("drm/msm/dsi/phy: Fix reading zero as PLL rates when unprepared")
Closes: https://lore.kernel.org/all/50a49d72-2b1e-471d-b0c4-d5a0b38b2a21@linaro.org/
Tested-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/683688/
Link: https://lore.kernel.org/r/20251027-topic-sm8x50-fix-dsi-bonded-v1-1-a477cd3f907d@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Hardware Programming Guide for DSI PHY says that PLL_SHUTDOWNB and
DIGTOP_PWRDN_B have to be asserted for any PLL register access.
Whenever dsi_pll_7nm_vco_recalc_rate() or dsi_pll_7nm_vco_set_rate()
were called on unprepared PLL, driver read values of zero leading to all
sort of further troubles, like failing to set pixel and byte clock
rates.
Asserting the PLL shutdown bit is done by dsi_pll_enable_pll_bias() (and
corresponding dsi_pll_disable_pll_bias()) which are called through the
code, including from PLL .prepare() and .unprepare() callbacks.
The .set_rate() and .recalc_rate() can be called almost anytime from
external users including times when PLL is or is not prepared, thus
driver should not interfere with the prepare status.
Implement simple reference counting for the PLL bias, so
set_rate/recalc_rate will not change the status of prepared PLL.
Issue of reading 0 in .recalc_rate() did not show up on existing
devices, but only after re-ordering the code for SM8750.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/673416/
Link: https://lore.kernel.org/r/20250908094950.72877-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Driver unconditionally saves current state on first init in
dsi_pll_7nm_init(), but does not save the VCO rate, only some of the
divider registers. The state is then restored during probe/enable via
msm_dsi_phy_enable() -> msm_dsi_phy_pll_restore_state() ->
dsi_7nm_pll_restore_state().
Restoring calls dsi_pll_7nm_vco_set_rate() with
pll_7nm->vco_current_rate=0, which basically overwrites existing rate of
VCO and messes with clock hierarchy, by setting frequency to 0 to clock
tree. This makes anyway little sense - VCO rate was not saved, so
should not be restored.
If PLL was not configured configure it to minimum rate to avoid glitches
and configuring entire in clock hierarchy to 0 Hz.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/657827/
Link: https://lore.kernel.org/r/20250610-b4-sm8750-display-v6-9-ee633e3ddbff@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
According to Hardware Programming Guide for DSI PHY, the retime buffer
resync should be done after PLL clock users (byte_clk and intf_byte_clk)
are enabled. Downstream also does it as part of configuring the PLL.
Driver was only turning off the resync FIFO buffer, but never bringing it
on again.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/657823/
Link: https://lore.kernel.org/r/20250610-b4-sm8750-display-v6-6-ee633e3ddbff@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
The round_rate() clk ops is deprecated, so migrate this driver from
round_rate() to determine_rate() using the Coccinelle semantic patch
on the cover letter of this series. The change to use clamp_t() was
done manually.
Signed-off-by: Brian Masney <bmasney@redhat.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/667874/
Link: https://lore.kernel.org/r/20250810-drm-msm-phy-clk-round-rate-v2-5-0fd1f7979c83@redhat.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
The round_rate() clk ops is deprecated, so migrate this driver from
round_rate() to determine_rate() using the Coccinelle semantic patch
on the cover letter of this series. The change to use clamp_t() was
done manually.
Signed-off-by: Brian Masney <bmasney@redhat.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/667872/
Link: https://lore.kernel.org/r/20250810-drm-msm-phy-clk-round-rate-v2-4-0fd1f7979c83@redhat.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
The round_rate() clk ops is deprecated, so migrate this driver from
round_rate() to determine_rate() using the Coccinelle semantic patch
on the cover letter of this series. The change to use clamp_t() was
done manually.
Signed-off-by: Brian Masney <bmasney@redhat.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/667870/
Link: https://lore.kernel.org/r/20250810-drm-msm-phy-clk-round-rate-v2-3-0fd1f7979c83@redhat.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
The round_rate() clk ops is deprecated, so migrate this driver from
round_rate() to determine_rate() using the Coccinelle semantic patch
on the cover letter of this series. The change to use clamp_t() was
done manually.
Signed-off-by: Brian Masney <bmasney@redhat.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/667869/
Link: https://lore.kernel.org/r/20250810-drm-msm-phy-clk-round-rate-v2-2-0fd1f7979c83@redhat.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
The round_rate() clk ops is deprecated, so migrate this driver from
round_rate() to determine_rate() using the Coccinelle semantic patch
on the cover letter of this series. The change to use clamp_t() was
done manually.
Signed-off-by: Brian Masney <bmasney@redhat.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/667866/
Link: https://lore.kernel.org/r/20250810-drm-msm-phy-clk-round-rate-v2-1-0fd1f7979c83@redhat.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
To configure and enable the DSI PHY PLL clocks, the MDSS AHB clock must
be active for MMIO operations. Typically, this AHB clock is enabled as
part of the DSI PHY interface enabling (dsi_phy_enable_resource).
However, since these PLL clocks are registered as clock entities, they
can be enabled independently of the DSI PHY interface, leading to
enabling failures and subsequent warnings:
```
msm_dsi_phy 5e94400.phy: [drm:dsi_pll_14nm_vco_prepare] *ERROR* DSI PLL lock failed
------------[ cut here ]------------
dsi0pllbyte already disabled
WARNING: CPU: 3 PID: 1 at drivers/clk/clk.c:1194 clk_core_disable+0xa4/0xac
CPU: 3 UID: 0 PID: 1 Comm: swapper/0 Tainted:
Tainted: [W]=WARN
Hardware name: Qualcomm Technologies, Inc. Robotics RB1 (DT)
pstate: 600000c5 (nZCv daIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[...]
```
This issue is particularly prevalent at boot time during the disabling of
unused clocks (clk_disable_unused()) which includes enabling the parent
clock(s) when CLK_OPS_PARENT_ENABLE flag is set (this is the case for the
14nm DSI PHY PLL consumers).
To resolve this issue, we move the AHB clock as a PM dependency of the DSI
PHY device (via pm_clk). Since the DSI PHY device is the parent of the PLL
clocks, this resolves the PLL/AHB dependency. Now the AHB clock is enabled
prior the PLL clk_prepare callback, as part of the runtime-resume chain.
We also eliminate dsi_phy_[enable|disable]_resource functions, which are
superseded by runtime PM.
Note that it breaks compatibility with kernels before 6.0, as we do not
support anymore the legacy `iface_clk` name.
Signed-off-by: Loic Poulain <loic.poulain@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/663239/
Link: https://lore.kernel.org/r/20250709140836.124143-1-loic.poulain@oss.qualcomm.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Data for HDMI, DSI and DP blocks only makes sense for the KMS parts of
the driver. Move corresponding data pointers from struct msm_drm_private
to struct msm_kms.
Suggested-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/662580/
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
Most of the driver code doesn't need to reach in to msm specific fields,
so just use the drm_gpuvm/drm_gpuva types directly. This should
hopefully improve commonality with other drivers and make the code
easier to understand.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
Tested-by: Antonino Maniscalco <antomani103@gmail.com>
Reviewed-by: Antonino Maniscalco <antomani103@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/661483/
Re-aligning naming to better match drm_gpuvm terminology will make
things less confusing at the end of the drm_gpuvm conversion.
This is just rename churn, no functional change.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
Tested-by: Antonino Maniscalco <antomani103@gmail.com>
Reviewed-by: Antonino Maniscalco <antomani103@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/661466/
Add support for DSI on Qualcomm SM8750 SoC with notable difference:
DSI PHY PLLs, the parents of pixel and byte clocks, cannot be used as
parents before DSI PHY is configured, the PLLs are prepared and their
initial rate is set. Therefore assigned-clock-parents are not working
here and driver is responsible for reparenting clocks with proper
procedure: see dsi_clk_init_6g_v2_9().
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/659619/
Link: https://lore.kernel.org/r/20250618-b4-sm8750-display-v7-7-a591c609743d@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Add support for DSI PHY v7.0 on Qualcomm SM8750 SoC which comes with an
incompatible hardware interface change:
ICODE_ACCUM_STATUS_LOW and ALOG_OBSV_BUS_STATUS_1 registers - their
offsets were just switched. Currently these registers are not used in
the driver, so the easiest is to document both but keep them commented
out to avoid conflict.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/659616/
Link: https://lore.kernel.org/r/20250618-b4-sm8750-display-v7-6-a591c609743d@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Driver unconditionally saves current state on first init in
dsi_pll_10nm_init(), but does not save the VCO rate, only some of the
divider registers. The state is then restored during probe/enable via
msm_dsi_phy_enable() -> msm_dsi_phy_pll_restore_state() ->
dsi_10nm_pll_restore_state().
Restoring calls dsi_pll_10nm_vco_set_rate() with
pll_10nm->vco_current_rate=0, which basically overwrites existing rate of
VCO and messes with clock hierarchy, by setting frequency to 0 to clock
tree. This makes anyway little sense - VCO rate was not saved, so
should not be restored.
If PLL was not configured configure it to minimum rate to avoid glitches
and configuring entire in clock hierarchy to 0 Hz.
Suggested-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/sz4kbwy5nwsebgf64ia7uq4ee7wbsa5uy3xmlqwcstsbntzcov@ew3dcyjdzmi2/
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Fixes: a4ccc37693 ("drm/msm/dsi_pll_10nm: restore VCO rate during
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/654796/
Link: https://lore.kernel.org/r/20250520111325.92352-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Backmerging to get v6.15-rc1 into drm-misc-next. Also fixes a
build issue when enabling CONFIG_DRM_SCHED_KUNIT_TEST.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
The drm_bridge structure contains an encoder pointer that is widely used
by bridge drivers. This pattern is largely documented as deprecated in
other KMS entities for atomic drivers.
However, one of the main use of that pointer is done in attach to just
call drm_bridge_attach on the next bridge to add it to the bridge list.
While this dereferences the bridge->encoder pointer, it's effectively
the same encoder the bridge was being attached to.
We can make it more explicit by adding the encoder the bridge is
attached to to the list of attach parameters. This also removes the need
to dereference bridge->encoder in most drivers.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250313-bridge-connector-v6-1-511c54a604fb@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
