Commit 45a3a8ef81 ("serial: core: Revert checks for tx runtime PM state")
caused a regression for Sun Ultra 60 for the sunsab driver as reported by
Nick Bowler <nbowler@draconx.ca>.
We need to add back the check runtime PM enabled state for serial port
controller device, I wrongly assumed earlier we could just remove it.
Fixes: 45a3a8ef81 ("serial: core: Revert checks for tx runtime PM state")
Cc: stable <stable@kernel.org>
Reported-by: Nick Bowler <nbowler@draconx.ca>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20240325071649.27040-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The uart_handle_cts_change() function in serial_core expects the caller
to hold uport->lock. For example, I have seen the below kernel splat,
when the Bluetooth driver is loaded on an i.MX28 board.
[ 85.119255] ------------[ cut here ]------------
[ 85.124413] WARNING: CPU: 0 PID: 27 at /drivers/tty/serial/serial_core.c:3453 uart_handle_cts_change+0xb4/0xec
[ 85.134694] Modules linked in: hci_uart bluetooth ecdh_generic ecc wlcore_sdio configfs
[ 85.143314] CPU: 0 PID: 27 Comm: kworker/u3:0 Not tainted 6.6.3-00021-gd62a2f068f92 #1
[ 85.151396] Hardware name: Freescale MXS (Device Tree)
[ 85.156679] Workqueue: hci0 hci_power_on [bluetooth]
(...)
[ 85.191765] uart_handle_cts_change from mxs_auart_irq_handle+0x380/0x3f4
[ 85.198787] mxs_auart_irq_handle from __handle_irq_event_percpu+0x88/0x210
(...)
Cc: stable@vger.kernel.org
Fixes: 4d90bb147e ("serial: core: Document and assert lock requirements for irq helpers")
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Emil Kronborg <emil.kronborg@protonmail.com>
Link: https://lore.kernel.org/r/20240320121530.11348-1-emil.kronborg@protonmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e5d6bd25f9 ("serial: 8250_dw: Do not reclock if already at
correct rate") breaks the dw UARTs on Intel Bay Trail (BYT) and
Cherry Trail (CHT) SoCs.
Before this change the RTL8732BS Bluetooth HCI which is found
connected over the dw UART on both BYT and CHT boards works properly:
Bluetooth: hci0: RTL: examining hci_ver=06 hci_rev=000b lmp_ver=06 lmp_subver=8723
Bluetooth: hci0: RTL: rom_version status=0 version=1
Bluetooth: hci0: RTL: loading rtl_bt/rtl8723bs_fw.bin
Bluetooth: hci0: RTL: loading rtl_bt/rtl8723bs_config-OBDA8723.bin
Bluetooth: hci0: RTL: cfg_sz 64, total sz 24508
Bluetooth: hci0: RTL: fw version 0x365d462e
where as after this change probing it fails:
Bluetooth: hci0: RTL: examining hci_ver=06 hci_rev=000b lmp_ver=06 lmp_subver=8723
Bluetooth: hci0: RTL: rom_version status=0 version=1
Bluetooth: hci0: RTL: loading rtl_bt/rtl8723bs_fw.bin
Bluetooth: hci0: RTL: loading rtl_bt/rtl8723bs_config-OBDA8723.bin
Bluetooth: hci0: RTL: cfg_sz 64, total sz 24508
Bluetooth: hci0: command 0xfc20 tx timeout
Bluetooth: hci0: RTL: download fw command failed (-110)
Revert the changes to fix this regression.
Fixes: e5d6bd25f9 ("serial: 8250_dw: Do not reclock if already at correct rate")
Cc: stable@vger.kernel.org
Cc: Peter Collingbourne <pcc@google.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Peter Collingbourne <pcc@google.com>
Link: https://lore.kernel.org/r/20240317214123.34482-1-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Goto the clean up path to clean up a couple clocks before returning
on this error path.
Fixes: 0087b9e694 ("serial: 8250_lpc18xx: Switch to use uart_read_port_properties()")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/92646c10-e0b5-4117-a9ac-ce9987d33ce3@moroto.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The log_martians variable is only used in an #ifdef, causing a 'make W=1'
warning with gcc:
net/ipv4/route.c: In function 'ip_rt_send_redirect':
net/ipv4/route.c:880:13: error: variable 'log_martians' set but not used [-Werror=unused-but-set-variable]
Change the #ifdef to an equivalent IS_ENABLED() to let the compiler
see where the variable is used.
Fixes: 30038fc61a ("net: ip_rt_send_redirect() optimization")
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20240408074219.3030256-2-arnd@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When CONFIG_IPV6_SUBTREES is disabled, the only user is hidden, causing
a 'make W=1' warning:
net/ipv6/ip6_fib.c: In function 'fib6_add':
net/ipv6/ip6_fib.c:1388:32: error: variable 'pn' set but not used [-Werror=unused-but-set-variable]
Add another #ifdef around the variable declaration, matching the other
uses in this file.
Fixes: 66729e18df ("[IPV6] ROUTE: Make sure we have fn->leaf when adding a node on subtree.")
Link: https://lore.kernel.org/netdev/20240322131746.904943-1-arnd@kernel.org/
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20240408074219.3030256-1-arnd@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The SOF driver has multiple profiles to select firmware/topology
prefix/names depending on the platform and ipc_type, and each of those
fields can be overridden with kernel parameters. This results in some
cases in confusion on what configuration is actually used in a given
test.
We currently log the firmware and topology names in the kernel logs,
but there's been an ask to add the information in debugfs to simplify
test scripts used by developers and CI.
This isn't meant to be a stable ABI used by apps, changes will be
allowed as needed.
Closes: https://github.com/thesofproject/linux/issues/3867
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://msgid.link/r/20240408194147.28919-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Introduce a new field in struct sof_ipc_pcm_ops that can be used to
restrict DSP D0i3 during S0ix suspend to IPC3. With IPC4, all streams
must be stopped before S0ix suspend.
Reviewed-by: Uday M Bhat <uday.m.bhat@intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://msgid.link/r/20240408194147.28919-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The commit cd6f2a2e63 ("ASoC: SOF: Intel: Set the default firmware
library path for IPC4") added the default_lib_path field for all
platforms, but this was missed when LunarLake was later introduced.
Fixes: 64a63d9914 ("ASoC: SOF: Intel: LNL: Add support for Lunarlake platform")
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://msgid.link/r/20240408194147.28919-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The ChainDMA operation differs from normal pipelines that it is only
created when the stream started, in fact a PCM using ChainDMA has no
pipelines, modules.
To reset a ChainDMA, it needs to be first allocated in firmware. When
PulseAudio/PipeWire starts, they will probe the PCMs by opening them, check
hw_params and then close the PCM without starting audio.
Unconditionally resetting the ChainDMA can result the following error:
ipc tx : 0xe040000|0x0: GLB_CHAIN_DMA
ipc tx reply: 0x2e000007|0x0: GLB_CHAIN_DMA
FW reported error: 7 - Unsupported operation requested
ipc error for msg 0xe040000|0x0
sof_pcm_stream_free: pcm_ops hw_free failed -22
Add a new chain_dma_allocated flag to sof_ipc4_pcm_stream_priv to store the
ChainDMA allocation state and use this flag to skip sending the reset if
the ChainDMA is not allocated.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://msgid.link/r/20240409110036.9411-5-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Using the sof_ipc4_timestamp_info struct directly as sps->private data
is too restrictive, add a new generic sof_ipc4_pcm_stream_priv struct
containing the time_info to allow new information to be stored in a
generic way.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://msgid.link/r/20240409110036.9411-4-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The pointer to sof_ipc4_timestamp_info named most of the time as
'time_info' only to be named as 'stream_info' or 'info' in two function.
Use the consistent name of 'time_info' throughout the file.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://msgid.link/r/20240409110036.9411-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Throughout the file the pointer for snd_sof_pcm_stream is named either
'stream' or (wrongly) 'spcm' which confuses the reader.
Use 'sps' for the pointer name as it is the most common name used in SOF
codebase.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://msgid.link/r/20240409110036.9411-2-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
These IOCTL commands should be implemented by setting attributes on the
superblock, rather than in the IOCTL hooks in struct file_operations.
By returning -ENOTTY instead of -ENOIOCTLCMD, we instruct the fs/ioctl.c
logic to return -ENOTTY immediately, rather than attempting to call
f_op->unlocked_ioctl() or f_op->compat_ioctl() as a fallback.
Why this is safe:
Before this change, fs/ioctl.c would unsuccessfully attempt calling the
IOCTL hooks, and then return -ENOTTY. By returning -ENOTTY directly, we
return the same error code immediately, but save ourselves the fallback
attempt.
Motivation:
This simplifies the logic for these IOCTL commands and lets us reason about
the side effects of these IOCTLs more easily. It will be possible to
permit these IOCTLs under LSM IOCTL policies, without having to worry about
them getting dispatched to problematic device drivers (which sometimes do
work before looking at the IOCTL command number).
Link: https://lore.kernel.org/all/cnwpkeovzbumhprco7q2c2y6zxzmxfpwpwe3tyy6c3gg2szgqd@vfzjaw5v5imr/
Cc: Kent Overstreet <kent.overstreet@linux.dev>
Cc: Christian Brauner <brauner@kernel.org>
Cc: Jan Kara <jack@suse.cz>
Cc: Dave Chinner <dchinner@redhat.com>
Cc: Darrick J. Wong <djwong@kernel.org>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Günther Noack <gnoack@google.com>
Link: https://lore.kernel.org/r/20240405214040.101396-2-gnoack@google.com
Acked-by: Kent Overstreet <kent.overstreet@linux.dev>
Signed-off-by: Christian Brauner <brauner@kernel.org>
NIX SQ mode and link backpressure configuration is required for
all platforms. But in current driver this code is wrongly placed
under specific platform check. This patch fixes the issue by
moving the code out of platform check.
Fixes: 5d9b976d44 ("octeontx2-af: Support fixed transmit scheduler topology")
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Link: https://lore.kernel.org/r/20240408063643.26288-1-gakula@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
As per the GICv4.1 spec (Arm IHI 0069H, 5.3.19):
"A VMAPP with {V, Alloc}=={0, x} is self-synchronizing, This means the ITS
command queue does not show the command as consumed until all of its
effects are completed."
Furthermore, VSYNC is allowed to deliver an SError when referencing a
non existent VPE.
By these definitions, a VMAPP followed by a VSYNC is a bug, as the
later references a VPE that has been unmapped by the former.
Fix it by eliding the VSYNC in this scenario.
Fixes: 64edfaa9a2 ("irqchip/gic-v4.1: Implement the v4.1 flavour of VMAPP")
Signed-off-by: Nianyao Tang <tangnianyao@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Link: https://lore.kernel.org/r/20240406022737.3898763-1-tangnianyao@huawei.com
I ran into a randconfig build failure with UBSAN using gcc-13.2:
arm-linux-gnueabi-ld: error: unplaced orphan section `.bss..Lubsan_data31' from `drivers/mtd/nand/raw/diskonchip.o'
I'm not entirely sure what is going on here, but I suspect this has something
to do with the check for the end of the doc_locations[] array that contains
an (unsigned long)0xffffffff element, which is compared against the signed
(int)0xffffffff. If this is the case, we should get a runtime check for
undefined behavior, but we instead get an unexpected build-time error.
I would have expected this to work fine on 32-bit architectures despite the
signed integer overflow, though on 64-bit architectures this likely won't
ever work.
Changing the contition to instead check for the size of the array makes the
code safe everywhere and avoids the ubsan check that leads to the link
error. The loop code goes back to before 2.6.12.
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240405143015.717429-1-arnd@kernel.org
While migrating to exec_ops in commit a82990c8a4 ("mtd: rawnand: qcom:
Add read/read_start ops in exec_op path"), OP_RESET_DEVICE command handling
got broken unintentionally. Right now for the OP_RESET_DEVICE command,
qcom_misc_cmd_type_exec() will simply return 0 without handling it. Even,
if that gets fixed, an unnecessary FLASH_STATUS read descriptor command is
being added in the middle and that seems to be causing the command to fail
on IPQ806x devices.
So let's fix the above two issues to make OP_RESET_DEVICE command working
again.
Fixes: a82990c8a4 ("mtd: rawnand: qcom: Add read/read_start ops in exec_op path")
Cc: stable@vger.kernel.org
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240404083157.940-1-ansuelsmth@gmail.com
Pull MD fix from Song:
"This change, by Yu Kuai, fixes a UAF in a corner case."
* tag 'md-6.9-20240408' of https://git.kernel.org/pub/scm/linux/kernel/git/song/md:
raid1: fix use-after-free for original bio in raid1_write_request()
This reverts:
nouveau/gsp: don't check devinit disable on GSP.
and applies a further fix.
It turns out the open gpu driver, checks this register,
but only for display.
Match that behaviour and in the turing path only disable
the display block. (ampere already only does displays).
Fixes: 5d4e8ae6e5 ("nouveau/gsp: don't check devinit disable on GSP.")
Reviewed-by: Danilo Krummrich <dakr@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240408064243.2219527-1-airlied@gmail.com
Branch History Injection (BHI) attacks may allow a malicious application to
influence indirect branch prediction in kernel by poisoning the branch
history. eIBRS isolates indirect branch targets in ring0. The BHB can
still influence the choice of indirect branch predictor entry, and although
branch predictor entries are isolated between modes when eIBRS is enabled,
the BHB itself is not isolated between modes.
Add mitigations against it either with the help of microcode or with
software sequences for the affected CPUs.
-----BEGIN PGP SIGNATURE-----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=W0W3
-----END PGP SIGNATURE-----
Merge tag 'nativebhi' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 mitigations from Thomas Gleixner:
"Mitigations for the native BHI hardware vulnerabilty:
Branch History Injection (BHI) attacks may allow a malicious
application to influence indirect branch prediction in kernel by
poisoning the branch history. eIBRS isolates indirect branch targets
in ring0. The BHB can still influence the choice of indirect branch
predictor entry, and although branch predictor entries are isolated
between modes when eIBRS is enabled, the BHB itself is not isolated
between modes.
Add mitigations against it either with the help of microcode or with
software sequences for the affected CPUs"
[ This also ends up enabling the full mitigation by default despite the
system call hardening, because apparently there are other indirect
calls that are still sufficiently reachable, and the 'auto' case just
isn't hardened enough.
We'll have some more inevitable tweaking in the future - Linus ]
* tag 'nativebhi' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
KVM: x86: Add BHI_NO
x86/bhi: Mitigate KVM by default
x86/bhi: Add BHI mitigation knob
x86/bhi: Enumerate Branch History Injection (BHI) bug
x86/bhi: Define SPEC_CTRL_BHI_DIS_S
x86/bhi: Add support for clearing branch history at syscall entry
x86/syscall: Don't force use of indirect calls for system calls
x86/bugs: Change commas to semicolons in 'spectre_v2' sysfs file
syzkaller started to report deadlock of unix_gc_lock after commit
4090fa373f ("af_unix: Replace garbage collection algorithm."), but
it just uncovers the bug that has been there since commit 314001f0bf
("af_unix: Add OOB support").
The repro basically does the following.
from socket import *
from array import array
c1, c2 = socketpair(AF_UNIX, SOCK_STREAM)
c1.sendmsg([b'a'], [(SOL_SOCKET, SCM_RIGHTS, array("i", [c2.fileno()]))], MSG_OOB)
c2.recv(1) # blocked as no normal data in recv queue
c2.close() # done async and unblock recv()
c1.close() # done async and trigger GC
A socket sends its file descriptor to itself as OOB data and tries to
receive normal data, but finally recv() fails due to async close().
The problem here is wrong handling of OOB skb in manage_oob(). When
recvmsg() is called without MSG_OOB, manage_oob() is called to check
if the peeked skb is OOB skb. In such a case, manage_oob() pops it
out of the receive queue but does not clear unix_sock(sk)->oob_skb.
This is wrong in terms of uAPI.
Let's say we send "hello" with MSG_OOB, and "world" without MSG_OOB.
The 'o' is handled as OOB data. When recv() is called twice without
MSG_OOB, the OOB data should be lost.
>>> from socket import *
>>> c1, c2 = socketpair(AF_UNIX, SOCK_STREAM, 0)
>>> c1.send(b'hello', MSG_OOB) # 'o' is OOB data
5
>>> c1.send(b'world')
5
>>> c2.recv(5) # OOB data is not received
b'hell'
>>> c2.recv(5) # OOB date is skipped
b'world'
>>> c2.recv(5, MSG_OOB) # This should return an error
b'o'
In the same situation, TCP actually returns -EINVAL for the last
recv().
Also, if we do not clear unix_sk(sk)->oob_skb, unix_poll() always set
EPOLLPRI even though the data has passed through by previous recv().
To avoid these issues, we must clear unix_sk(sk)->oob_skb when dequeuing
it from recv queue.
The reason why the old GC did not trigger the deadlock is because the
old GC relied on the receive queue to detect the loop.
When it is triggered, the socket with OOB data is marked as GC candidate
because file refcount == inflight count (1). However, after traversing
all inflight sockets, the socket still has a positive inflight count (1),
thus the socket is excluded from candidates. Then, the old GC lose the
chance to garbage-collect the socket.
With the old GC, the repro continues to create true garbage that will
never be freed nor detected by kmemleak as it's linked to the global
inflight list. That's why we couldn't even notice the issue.
Fixes: 314001f0bf ("af_unix: Add OOB support")
Reported-by: syzbot+7f7f201cc2668a8fd169@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=7f7f201cc2668a8fd169
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20240405221057.2406-1-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
- fix return types: promoting from unsigned to ssize_t does not do what
we want here, and was pointless since the rest of the eytzinger code
is u32
- nr, not size
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
The ks8851_irq() thread may call ks8851_rx_pkts() in case there are
any packets in the MAC FIFO, which calls netif_rx(). This netif_rx()
implementation is guarded by local_bh_disable() and local_bh_enable().
The local_bh_enable() may call do_softirq() to run softirqs in case
any are pending. One of the softirqs is net_rx_action, which ultimately
reaches the driver .start_xmit callback. If that happens, the system
hangs. The entire call chain is below:
ks8851_start_xmit_par from netdev_start_xmit
netdev_start_xmit from dev_hard_start_xmit
dev_hard_start_xmit from sch_direct_xmit
sch_direct_xmit from __dev_queue_xmit
__dev_queue_xmit from __neigh_update
__neigh_update from neigh_update
neigh_update from arp_process.constprop.0
arp_process.constprop.0 from __netif_receive_skb_one_core
__netif_receive_skb_one_core from process_backlog
process_backlog from __napi_poll.constprop.0
__napi_poll.constprop.0 from net_rx_action
net_rx_action from __do_softirq
__do_softirq from call_with_stack
call_with_stack from do_softirq
do_softirq from __local_bh_enable_ip
__local_bh_enable_ip from netif_rx
netif_rx from ks8851_irq
ks8851_irq from irq_thread_fn
irq_thread_fn from irq_thread
irq_thread from kthread
kthread from ret_from_fork
The hang happens because ks8851_irq() first locks a spinlock in
ks8851_par.c ks8851_lock_par() spin_lock_irqsave(&ksp->lock, ...)
and with that spinlock locked, calls netif_rx(). Once the execution
reaches ks8851_start_xmit_par(), it calls ks8851_lock_par() again
which attempts to claim the already locked spinlock again, and the
hang happens.
Move the do_softirq() call outside of the spinlock protected section
of ks8851_irq() by disabling BHs around the entire spinlock protected
section of ks8851_irq() handler. Place local_bh_enable() outside of
the spinlock protected section, so that it can trigger do_softirq()
without the ks8851_par.c ks8851_lock_par() spinlock being held, and
safely call ks8851_start_xmit_par() without attempting to lock the
already locked spinlock.
Since ks8851_irq() is protected by local_bh_disable()/local_bh_enable()
now, replace netif_rx() with __netif_rx() which is not duplicating the
local_bh_disable()/local_bh_enable() calls.
Fixes: 797047f875 ("net: ks8851: Implement Parallel bus operations")
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20240405203204.82062-2-marex@denx.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Both ks8851_rx_skb_par() and ks8851_rx_skb_spi() call netif_rx(skb),
inline the netif_rx(skb) call directly into ks8851_common.c and drop
the .rx_skb callback and ks8851_rx_skb() wrapper. This removes one
indirect call from the driver, no functional change otherwise.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20240405203204.82062-1-marex@denx.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is code in the SCSI core that sets the SCMD_FAIL_IF_RECOVERING
flag but there is no code that clears this flag. Instead of only clearing
SCMD_INITIALIZED in scsi_end_request(), clear all flags. It is never
necessary to preserve any command flags inside scsi_end_request().
Cc: stable@vger.kernel.org
Fixes: 310bcaef6d ("scsi: core: Support failing requests while recovering")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20240325224417.1477135-1-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use the raw/true host.MAXPHYADDR when deciding whether or not KVM must
intercept #PFs when allow_smaller_maxphyaddr is enabled, as any adjustments
the kernel makes to boot_cpu_data.x86_phys_bits to account for MKTME KeyID
bits do not apply to the guest physical address space. I.e. the KeyID are
off-limits for host physical addresses, but are not reserved for GPAs as
far as hardware is concerned.
Signed-off-by: Tao Su <tao1.su@linux.intel.com>
Link: https://lore.kernel.org/r/20240319031111.495006-1-tao1.su@linux.intel.com
[sean: massage changelog]
Signed-off-by: Sean Christopherson <seanjc@google.com>
commit 849c181643 ("KVM: selftests: fix supported_flags for aarch64")
fixed the set-memory-region test for aarch64 by declaring the read-only
flag is supported. riscv also supports the read-only flag. Fix it too.
Signed-off-by: Andrew Jones <ajones@ventanamicro.com>
Link: https://lore.kernel.org/r/20240403123300.63923-2-ajones@ventanamicro.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
max_guest_memory_test uses ucalls to sync with the host, but
it also resets the guest RIP back to its initial value in between
tests stages.
This makes the guest never reach the code which frees the ucall struct
and since a fixed pool of 512 ucall structs is used, the test starts
to fail when more that 256 vCPUs are used.
Fix that by replacing the manual register reset with a loop in
the guest code.
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Link: https://lore.kernel.org/r/20240315143507.102629-1-mlevitsk@redhat.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Add a guest assert in the PMU counters test to verify that KVM stuffs
the vCPU's post-RESET value to globally enable all general purpose
counters. Per Intel's SDM,
IA32_PERF_GLOBAL_CTRL: Sets bits n-1:0 and clears the upper bits.
and
Where "n" is the number of general-purpose counters available in
the processor.
For the edge case where there are zero GP counters, follow the spirit
of the architecture, not the SDM's literal wording, which doesn't account
for this possibility and would require the CPU to set _all_ bits in
PERF_GLOBAL_CTRL.
Reviewed-by: Dapeng Mi <dapeng1.mi@linux.intel.com>
Tested-by: Dapeng Mi <dapeng1.mi@linux.intel.com>
Link: https://lore.kernel.org/r/20240309013641.1413400-3-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Set the enable bits for general purpose counters in IA32_PERF_GLOBAL_CTRL
when refreshing the PMU to emulate the MSR's architecturally defined
post-RESET behavior. Per Intel's SDM:
IA32_PERF_GLOBAL_CTRL: Sets bits n-1:0 and clears the upper bits.
and
Where "n" is the number of general-purpose counters available in the processor.
AMD also documents this behavior for PerfMonV2 CPUs in one of AMD's many
PPRs.
Do not set any PERF_GLOBAL_CTRL bits if there are no general purpose
counters, although a literal reading of the SDM would require the CPU to
set either bits 63:0 or 31:0. The intent of the behavior is to globally
enable all GP counters; honor the intent, if not the letter of the law.
Leaving PERF_GLOBAL_CTRL '0' effectively breaks PMU usage in guests that
haven't been updated to work with PMUs that support PERF_GLOBAL_CTRL.
This bug was recently exposed when KVM added supported for AMD's
PerfMonV2, i.e. when KVM started exposing a vPMU with PERF_GLOBAL_CTRL to
guest software that only knew how to program v1 PMUs (that don't support
PERF_GLOBAL_CTRL).
Failure to emulate the post-RESET behavior results in such guests
unknowingly leaving all general purpose counters globally disabled (the
entire reason the post-RESET value sets the GP counter enable bits is to
maintain backwards compatibility).
The bug has likely gone unnoticed because PERF_GLOBAL_CTRL has been
supported on Intel CPUs for as long as KVM has existed, i.e. hardly anyone
is running guest software that isn't aware of PERF_GLOBAL_CTRL on Intel
PMUs. And because up until v6.0, KVM _did_ emulate the behavior for Intel
CPUs, although the old behavior was likely dumb luck.
Because (a) that old code was also broken in its own way (the history of
this code is a comedy of errors), and (b) PERF_GLOBAL_CTRL was documented
as having a value of '0' post-RESET in all SDMs before March 2023.
Initial vPMU support in commit f5132b0138 ("KVM: Expose a version 2
architectural PMU to a guests") *almost* got it right (again likely by
dumb luck), but for some reason only set the bits if the guest PMU was
advertised as v1:
if (pmu->version == 1) {
pmu->global_ctrl = (1 << pmu->nr_arch_gp_counters) - 1;
return;
}
Commit f19a0c2c2e ("KVM: PMU emulation: GLOBAL_CTRL MSR should be
enabled on reset") then tried to remedy that goof, presumably because
guest PMUs were leaving PERF_GLOBAL_CTRL '0', i.e. weren't enabling
counters.
pmu->global_ctrl = ((1 << pmu->nr_arch_gp_counters) - 1) |
(((1ull << pmu->nr_arch_fixed_counters) - 1) << X86_PMC_IDX_FIXED);
pmu->global_ctrl_mask = ~pmu->global_ctrl;
That was KVM's behavior up until commit c49467a45f ("KVM: x86/pmu:
Don't overwrite the pmu->global_ctrl when refreshing") removed
*everything*. However, it did so based on the behavior defined by the
SDM , which at the time stated that "Global Perf Counter Controls" is
'0' at Power-Up and RESET.
But then the March 2023 SDM (325462-079US), stealthily changed its
"IA-32 and Intel 64 Processor States Following Power-up, Reset, or INIT"
table to say:
IA32_PERF_GLOBAL_CTRL: Sets bits n-1:0 and clears the upper bits.
Note, kvm_pmu_refresh() can be invoked multiple times, i.e. it's not a
"pure" RESET flow. But it can only be called prior to the first KVM_RUN,
i.e. the guest will only ever observe the final value.
Note #2, KVM has always cleared global_ctrl during refresh (see commit
f5132b0138 ("KVM: Expose a version 2 architectural PMU to a guests")),
i.e. there is no danger of breaking existing setups by clobbering a value
set by userspace.
Reported-by: Babu Moger <babu.moger@amd.com>
Cc: Sandipan Das <sandipan.das@amd.com>
Cc: Like Xu <like.xu.linux@gmail.com>
Cc: Mingwei Zhang <mizhang@google.com>
Cc: Dapeng Mi <dapeng1.mi@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Dapeng Mi <dapeng1.mi@linux.intel.com>
Tested-by: Dapeng Mi <dapeng1.mi@linux.intel.com>
Link: https://lore.kernel.org/r/20240309013641.1413400-2-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Fix KVM_SET_MEMORY_ATTRIBUTES to not overflow lpage_info array and trigger
KASAN splat, as seen in the private_mem_conversions_test selftest.
When memory attributes are set on a GFN range, that range will have
specific properties applied to the TDP. A huge page cannot be used when
the attributes are inconsistent, so they are disabled for those the
specific huge pages. For internal KVM reasons, huge pages are also not
allowed to span adjacent memslots regardless of whether the backing memory
could be mapped as huge.
What GFNs support which huge page sizes is tracked by an array of arrays
'lpage_info' on the memslot, of ‘kvm_lpage_info’ structs. Each index of
lpage_info contains a vmalloc allocated array of these for a specific
supported page size. The kvm_lpage_info denotes whether a specific huge
page (GFN and page size) on the memslot is supported. These arrays include
indices for unaligned head and tail huge pages.
Preventing huge pages from spanning adjacent memslot is covered by
incrementing the count in head and tail kvm_lpage_info when the memslot is
allocated, but disallowing huge pages for memory that has mixed attributes
has to be done in a more complicated way. During the
KVM_SET_MEMORY_ATTRIBUTES ioctl KVM updates lpage_info for each memslot in
the range that has mismatched attributes. KVM does this a memslot at a
time, and marks a special bit, KVM_LPAGE_MIXED_FLAG, in the kvm_lpage_info
for any huge page. This bit is essentially a permanently elevated count.
So huge pages will not be mapped for the GFN at that page size if the
count is elevated in either case: a huge head or tail page unaligned to
the memslot or if KVM_LPAGE_MIXED_FLAG is set because it has mixed
attributes.
To determine whether a huge page has consistent attributes, the
KVM_SET_MEMORY_ATTRIBUTES operation checks an xarray to make sure it
consistently has the incoming attribute. Since level - 1 huge pages are
aligned to level huge pages, it employs an optimization. As long as the
level - 1 huge pages are checked first, it can just check these and assume
that if each level - 1 huge page contained within the level sized huge
page is not mixed, then the level size huge page is not mixed. This
optimization happens in the helper hugepage_has_attrs().
Unfortunately, although the kvm_lpage_info array representing page size
'level' will contain an entry for an unaligned tail page of size level,
the array for level - 1 will not contain an entry for each GFN at page
size level. The level - 1 array will only contain an index for any
unaligned region covered by level - 1 huge page size, which can be a
smaller region. So this causes the optimization to overflow the level - 1
kvm_lpage_info and perform a vmalloc out of bounds read.
In some cases of head and tail pages where an overflow could happen,
callers skip the operation completely as KVM_LPAGE_MIXED_FLAG is not
required to prevent huge pages as discussed earlier. But for memslots that
are smaller than the 1GB page size, it does call hugepage_has_attrs(). In
this case the huge page is both the head and tail page. The issue can be
observed simply by compiling the kernel with CONFIG_KASAN_VMALLOC and
running the selftest “private_mem_conversions_test”, which produces the
output like the following:
BUG: KASAN: vmalloc-out-of-bounds in hugepage_has_attrs+0x7e/0x110
Read of size 4 at addr ffffc900000a3008 by task private_mem_con/169
Call Trace:
dump_stack_lvl
print_report
? __virt_addr_valid
? hugepage_has_attrs
? hugepage_has_attrs
kasan_report
? hugepage_has_attrs
hugepage_has_attrs
kvm_arch_post_set_memory_attributes
kvm_vm_ioctl
It is a little ambiguous whether the unaligned head page (in the bug case
also the tail page) should be expected to have KVM_LPAGE_MIXED_FLAG set.
It is not functionally required, as the unaligned head/tail pages will
already have their kvm_lpage_info count incremented. The comments imply
not setting it on unaligned head pages is intentional, so fix the callers
to skip trying to set KVM_LPAGE_MIXED_FLAG in this case, and in doing so
not call hugepage_has_attrs().
Cc: stable@vger.kernel.org
Fixes: 90b4fe1798 ("KVM: x86: Disallow hugepages when memory attributes are mixed")
Signed-off-by: Rick Edgecombe <rick.p.edgecombe@intel.com>
Reviewed-by: Kai Huang <kai.huang@intel.com>
Reviewed-by: Chao Peng <chao.p.peng@linux.intel.com>
Link: https://lore.kernel.org/r/20240314212902.2762507-1-rick.p.edgecombe@intel.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Drop support for virtualizing adaptive PEBS, as KVM's implementation is
architecturally broken without an obvious/easy path forward, and because
exposing adaptive PEBS can leak host LBRs to the guest, i.e. can leak
host kernel addresses to the guest.
Bug #1 is that KVM doesn't account for the upper 32 bits of
IA32_FIXED_CTR_CTRL when (re)programming fixed counters, e.g
fixed_ctrl_field() drops the upper bits, reprogram_fixed_counters()
stores local variables as u8s and truncates the upper bits too, etc.
Bug #2 is that, because KVM _always_ sets precise_ip to a non-zero value
for PEBS events, perf will _always_ generate an adaptive record, even if
the guest requested a basic record. Note, KVM will also enable adaptive
PEBS in individual *counter*, even if adaptive PEBS isn't exposed to the
guest, but this is benign as MSR_PEBS_DATA_CFG is guaranteed to be zero,
i.e. the guest will only ever see Basic records.
Bug #3 is in perf. intel_pmu_disable_fixed() doesn't clear the upper
bits either, i.e. leaves ICL_FIXED_0_ADAPTIVE set, and
intel_pmu_enable_fixed() effectively doesn't clear ICL_FIXED_0_ADAPTIVE
either. I.e. perf _always_ enables ADAPTIVE counters, regardless of what
KVM requests.
Bug #4 is that adaptive PEBS *might* effectively bypass event filters set
by the host, as "Updated Memory Access Info Group" records information
that might be disallowed by userspace via KVM_SET_PMU_EVENT_FILTER.
Bug #5 is that KVM doesn't ensure LBR MSRs hold guest values (or at least
zeros) when entering a vCPU with adaptive PEBS, which allows the guest
to read host LBRs, i.e. host RIPs/addresses, by enabling "LBR Entries"
records.
Disable adaptive PEBS support as an immediate fix due to the severity of
the LBR leak in particular, and because fixing all of the bugs will be
non-trivial, e.g. not suitable for backporting to stable kernels.
Note! This will break live migration, but trying to make KVM play nice
with live migration would be quite complicated, wouldn't be guaranteed to
work (i.e. KVM might still kill/confuse the guest), and it's not clear
that there are any publicly available VMMs that support adaptive PEBS,
let alone live migrate VMs that support adaptive PEBS, e.g. QEMU doesn't
support PEBS in any capacity.
Link: https://lore.kernel.org/all/20240306230153.786365-1-seanjc@google.com
Link: https://lore.kernel.org/all/ZeepGjHCeSfadANM@google.com
Fixes: c59a1f106f ("KVM: x86/pmu: Add IA32_PEBS_ENABLE MSR emulation for extended PEBS")
Cc: stable@vger.kernel.org
Cc: Like Xu <like.xu.linux@gmail.com>
Cc: Mingwei Zhang <mizhang@google.com>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: Zhang Xiong <xiong.y.zhang@intel.com>
Cc: Lv Zhiyuan <zhiyuan.lv@intel.com>
Cc: Dapeng Mi <dapeng1.mi@intel.com>
Cc: Jim Mattson <jmattson@google.com>
Acked-by: Like Xu <likexu@tencent.com>
Link: https://lore.kernel.org/r/20240307005833.827147-1-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Explicit disallow activating a gfn_to_pfn_cache with an error gpa, i.e.
INVALID_GPA, to ensure that KVM doesn't mistake a GPA-based cache for an
HVA-based cache (KVM uses INVALID_GPA as a magic value to differentiate
between GPA-based and HVA-based caches).
WARN if KVM attempts to activate a cache with INVALID_GPA, purely so that
new caches need to at least consider what to do with a "bad" GPA, as all
existing usage of kvm_gpc_activate() guarantees gpa != INVALID_GPA. I.e.
removing the WARN in the future is completely reasonable if doing so would
yield cleaner/better code overall.
Reviewed-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Paul Durrant <paul@xen.org>
Link: https://lore.kernel.org/r/20240320001542.3203871-4-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
When activating a gfn_to_pfn_cache, verify that the offset+length is sane
and usable before marking the cache active. Letting __kvm_gpc_refresh()
detect the problem results in a cache being marked active without setting
the GPA (or any other fields), which in turn results in KVM trying to
refresh a cache with INVALID_GPA.
Attempting to refresh a cache with INVALID_GPA isn't functionally
problematic, but it runs afoul of the sanity check that exactly one of
GPA or userspace HVA is valid, i.e. that a cache is either GPA-based or
HVA-based.
Reported-by: syzbot+106a4f72b0474e1d1b33@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/all/0000000000005fa5cc0613f1cebd@google.com
Fixes: 721f5b0dda ("KVM: pfncache: allow a cache to be activated with a fixed (userspace) HVA")
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Paul Durrant <paul@xen.org>
Reviewed-by: Paul Durrant <paul@xen.org>
Reviewed-by: David Woodhouse <dwmw@amazon.co.uk>
Link: https://lore.kernel.org/r/20240320001542.3203871-3-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Add a helper to check that the incoming length for a gfn_to_pfn_cache is
valid with respect to the cache's GPA and/or HVA. To avoid activating a
cache with a bogus GPA, a future fix will fork the page split check in
the inner refresh path into activate() and the public rerfresh() APIs, at
which point KVM will check the length in three separate places.
Deliberately keep the "page offset" logic open coded, as the only other
path that consumes the offset, __kvm_gpc_refresh(), already needs to
differentiate between GPA-based and HVA-based caches, and it's not obvious
that using a helper is a net positive in overall code readability.
Note, for GPA-based caches, this has a subtle side effect of using the GPA
instead of the resolved HVA in the check() path, but that should be a nop
as the HVA offset is derived from the GPA, i.e. the two offsets are
identical, barring a KVM bug.
Reviewed-by: Paul Durrant <paul@xen.org>
Reviewed-by: David Woodhouse <dwmw@amazon.co.uk>
Link: https://lore.kernel.org/r/20240320001542.3203871-2-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEE8rQSAMVO+zA4DBdWxWXV+ddtWDsFAmYQIdIACgkQxWXV+ddt
WDvjmw/+KahIHfFt17cM5uZpiETcL9v44uT0Y69r0bMpw8Vy/cmE+rmGfyERr8YN
v68U/hpWHD2mYhxL01EHut2X/MRA4zmAcWUKVu1vk0d/9Vp/01wPJfKyvX6q388/
dFtPtzqXxj0uIwO5lRIk+dJuvShtfCps2rx/zcBUoaQYljIDNfhrWscfV4nIzqlR
BF7GX3b22rlw8q1dXAXWW+zTk3tey8Jxj+jmShyoPxcGMDK4jmNyaFu1WSIFfSdc
ns5Kii7/4tIBqpqPCr/FMGXQjdEZGw9ZTiAO4nUjtyoCTO3l/jMVYoo7llJR9dtv
Fgtej0MLlAapX2mJ65xOBO6OvCIM8VwrY+DfIDeWxtDONmrGxBUIMTJIjSq3oGEi
Mh0CbnpISGj9zQlR4raOavtgxmbdXnhdvLcp2Uv+VcJnEyCtHMmVLx9yNMKqjHje
oJHtuJiEeqlB66xZEYx3qA8SIdaJGhB/HluU9Vyg67AJTJUcCzuxZlqaC+oSOxfj
GYgY66BHD+ZKRKUFw7EylohnhvsMcmFhMSeBLzMuSaqEig4dmv4cFenad06up6c+
c0obH8oKsaA05gS3sMshmkNtBm8ms1OP2rWebjQWmmXhCOWLPqcGs5AxYeqvRdzx
eqFNKhRw+JH1mFmhEtY/Y+4OX6eTlluSxoKxZYWfAX1xvlr94U4=
=XtPw
-----END PGP SIGNATURE-----
Merge tag 'for-6.9-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"Several fixes to qgroups that have been recently identified by test
generic/475:
- fix prealloc reserve leak in subvolume operations
- various other fixes in reservation setup, conversion or cleanup"
* tag 'for-6.9-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: always clear PERTRANS metadata during commit
btrfs: make btrfs_clear_delalloc_extent() free delalloc reserve
btrfs: qgroup: convert PREALLOC to PERTRANS after record_root_in_trans
btrfs: record delayed inode root in transaction
btrfs: qgroup: fix qgroup prealloc rsv leak in subvolume operations
btrfs: qgroup: correctly model root qgroup rsv in convert
These entries are necessary to scale the interconnect bandwidth while
operating in Gear 5.
Cc: Amit Pundir <amit.pundir@linaro.org>
Fixes: 03ce80a1bb ("scsi: ufs: qcom: Add support for scaling interconnects")
Tested-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240403-ufs-icc-fix-v2-1-958412a5eb45@linaro.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The declarations of the tx_rx_evt class and the rdev_set_antenna event
use the wrong order of arguments in the TP_ARGS macro.
Fix the order of arguments in the TP_ARGS macro.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Igor Artemiev <Igor.A.Artemiev@mcst.ru>
Link: https://msgid.link/20240405152431.270267-1-Igor.A.Artemiev@mcst.ru
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Logic inside ieee80211_rx_mgmt_beacon accesses the
mgmt->u.beacon.timestamp field without first checking whether the beacon
received is non-S1G format.
Fix the problem by checking the beacon is non-S1G format to avoid access
of the mgmt->u.beacon.timestamp field.
Signed-off-by: Richard Kinder <richard.kinder@gmail.com>
Link: https://msgid.link/20240328005725.85355-1-richard.kinder@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Intel processors that aren't vulnerable to BHI will set
MSR_IA32_ARCH_CAPABILITIES[BHI_NO] = 1;. Guests may use this BHI_NO bit to
determine if they need to implement BHI mitigations or not. Allow this bit
to be passed to the guests.
Signed-off-by: Daniel Sneddon <daniel.sneddon@linux.intel.com>
Signed-off-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Signed-off-by: Daniel Sneddon <daniel.sneddon@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexandre Chartre <alexandre.chartre@oracle.com>
Reviewed-by: Josh Poimboeuf <jpoimboe@kernel.org>
BHI mitigation mode spectre_bhi=auto does not deploy the software
mitigation by default. In a cloud environment, it is a likely scenario
where userspace is trusted but the guests are not trusted. Deploying
system wide mitigation in such cases is not desirable.
Update the auto mode to unconditionally mitigate against malicious
guests. Deploy the software sequence at VMexit in auto mode also, when
hardware mitigation is not available. Unlike the force =on mode,
software sequence is not deployed at syscalls in auto mode.
Suggested-by: Alexandre Chartre <alexandre.chartre@oracle.com>
Signed-off-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Signed-off-by: Daniel Sneddon <daniel.sneddon@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexandre Chartre <alexandre.chartre@oracle.com>
Reviewed-by: Josh Poimboeuf <jpoimboe@kernel.org>
Branch history clearing software sequences and hardware control
BHI_DIS_S were defined to mitigate Branch History Injection (BHI).
Add cmdline spectre_bhi={on|off|auto} to control BHI mitigation:
auto - Deploy the hardware mitigation BHI_DIS_S, if available.
on - Deploy the hardware mitigation BHI_DIS_S, if available,
otherwise deploy the software sequence at syscall entry and
VMexit.
off - Turn off BHI mitigation.
The default is auto mode which does not deploy the software sequence
mitigation. This is because of the hardening done in the syscall
dispatch path, which is the likely target of BHI.
Signed-off-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Signed-off-by: Daniel Sneddon <daniel.sneddon@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexandre Chartre <alexandre.chartre@oracle.com>
Reviewed-by: Josh Poimboeuf <jpoimboe@kernel.org>
Mitigation for BHI is selected based on the bug enumeration. Add bits
needed to enumerate BHI bug.
Signed-off-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Signed-off-by: Daniel Sneddon <daniel.sneddon@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexandre Chartre <alexandre.chartre@oracle.com>
Reviewed-by: Josh Poimboeuf <jpoimboe@kernel.org>
