Qualcomm PM4125 codec is always a single device on the board, however
nothing stops board designers to have two of them, thus same device
driver could probe twice.
Device driver is not ready for that case, because it allocates
statically 'struct regmap_irq_chip' as non-const and stores during
component bind in 'irq_drv_data' member a pointer to per-probe state
container ('struct pm4125_priv').
Second component bind would overwrite the 'irq_drv_data' from previous
device probe, so interrupts would be executed in wrong context.
The fix makes use of currently unused 'struct pm4125_priv' member
'pm4125_regmap_irq_chip', but renames it to a shorter name.
Fixes: 8ad5294849 ("ASoC: codecs: add new pm4125 audio codec driver")
Cc: stable@vger.kernel.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20251023-asoc-regmap-irq-chip-v1-1-17ad32680913@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
In boards like adl_lt6911_hdmi_ssp/mtl_lt6911_hdmi_ssp/rpl_lt6911_hdmi_ssp,
HDMI is supported both for playback via normal HDA display codec,
as well as PCM capture from HDMI-In over I2S.
The common board driver function hda_dsp_hdmi_pcm_handle() has an
invalid assumption that "HDMI" is only used to identify playback HDMI
PCMs on the card. This will result in failures if HDMI-In PCMs are
defined in topology using the string "HDMI", and they are registered
before the playback PCMs.
Fix the issue by explicitly looking for FE playback PCMs.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://patch.msgid.link/20251112115045.337062-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Richard Fitzgerald <rf@opensource.cirrus.com>:
These two patches add ALSA controls to support restoring factory calibration
during OS boot on ChromeOS.
ChromeOS applies calibration during boot using a process that has restricted
access permissions. This process needs ALSA controls for all settings that
it must restore.
Add an ALSA control (CAL_DATA) that can be used to restore amp calibration,
instead of using debugfs. A readback control (CAL_DATA_RB) is also added
for factory testing.
On ChromeOS the process that restores amp calibration from NVRAM has
limited permissions and cannot access debugfs. It requires an ALSA control
that it can write the calibration blob into. ChromeOS also restricts access
to ALSA controls, which avoids the risk of accidental or malicious
overwriting of good calibration data with bad data. As this control is not
needed for normal Linux-based distros it is a Kconfig option.
A separate control, CAL_DATA_RB, provides a readback of the current
calibration data, which could be either from a write to CAL_DATA or the
result of factory production-line calibration.
The write and read are intentionally separate controls to defeat "dumb"
save-and-restore tools like alsa-restore that assume it is safe to save
all control values and write them back in any order at some undefined
future time. Such behavior carries the risk of restoring stale or bad data
over the top of good data.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://patch.msgid.link/20251111130850.513969-3-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Create an ALSA control to read the value of the firmware
CAL_SET_STATUS control. This reports whether the firmware is
using a calibration blob or the default calibration from the
.bin file.
The firmware only reports a valid value in this register while
audio is actually playing and the internal PLL is locked to the
audio clock. Otherwise it returns a status of "unknown".
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://patch.msgid.link/20251111130850.513969-2-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds Cirrus codec internal speaker configuration
to support the cs42l43_l3_cs35l56_l2 machine.
Signed-off-by: Mac Chiang <mac.chiang@intel.com>
Reviewed-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://patch.msgid.link/20251111123737.246626-7-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds the aggregated mode support:
cs42l43 codec with left and right tweeters on soundwire link 3,
cs35l56 left and right woofers on soundwire link 2.
Signed-off-by: Mac Chiang <mac.chiang@intel.com>
Reviewed-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://patch.msgid.link/20251111123737.246626-6-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The bt_link_mask value is from NHLT. The BT dai link should be created
if bt_link_mask is set. Besides, hda_machine_select() will look for the
topology with BT BE.
Suggested-by: Mac Chiang <mac.chiang@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://patch.msgid.link/20251111123737.246626-5-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This SKU does not use the RT722 internal speaker. Add
SOC_SDW_CODEC_SPKR to prevent DAI being created via
codec_info_list.dais.quirk_exclude.
Other SKUs continue to check higher-priority sdca_functions
when the BIOS SDCA property is present.
Signed-off-by: Mac Chiang <mac.chiang@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://patch.msgid.link/20251111123737.246626-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for the RT722 codec on SoundWire link 0,
and RT1320 left and right amplifiers on links 2 and 3, respectively.
Signed-off-by: Mac Chiang <mac.chiang@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://patch.msgid.link/20251111123737.246626-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
adding quirk override support to configure different quirk configuration
at runtime.
Signed-off-by: Balamurugan C <balamurugan.c@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://patch.msgid.link/20251111103512.244147-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Adjust the error codes returned by the calibration debugfs files
to provide a wider range of errors and make them more consistent.
There is a limited number of standard errors and it's not always
easy to find an error code that accurately describes what happened.
Additionally, user code often uses strerror() or something similar
to report a generic error description. The original calibration
code used a limited set of errors to attempt to avoid user error
strings that would be confusing or unclear on a file read/write.
However, this restricts the ability to provide informative errors.
This limited error range didn't help very much with debugging so
it has been expanded, rather than worrying about what strerror()
would return.
The errors are now more consistent:
ENXIO Calibration is not supported by the driver.
EOPNOTSUPP The given calibration command is not supported.
EBUSY Cannot calibrate because the amp is playing audio.
ERANGE Calibration result was out-of-range.
ETIMEDOUT Calibration did not complete.
EMSGSIZE Blob written to cal_data is the wrong size.
ENODATA No calibration data available to read from cal_data,
or
Blob written to cal_data does not contain calibration,
or
No calibration data available to save to UEFI.
EIO General failure to communicate with the firmware, mainly
indicating that firmware controls are missing.
EINVAL Has its normal meaning that an invalid argument was passed.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://patch.msgid.link/20251110114327.84370-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Consolidate simple audio codec (one compatible string, one reg, one
optional reset-gpios and '#sound-dai-cells' 0) to a trivial-codec.yaml.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20251031144622.4033833-1-Frank.Li@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In the past %pK was preferable to %p as it would not leak raw pointer
values into the kernel log.
Since commit ad67b74d24 ("printk: hash addresses printed with %p")
the regular %p has been improved to avoid this issue.
Furthermore, restricted pointers ("%pK") were never meant to be used
through printk(). They can still unintentionally leak raw pointers or
acquire sleeping locks in atomic contexts.
Switch to the regular pointer formatting which is safer and
easier to reason about.
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Link: https://patch.msgid.link/20251106-restricted-pointers-stm-v1-1-7d03eb5020ba@linutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
During firmware download, if the size of the firmware is too small,
it wrongly assumes the firmware download is successful. If there is
size mismatch with chunk's header, invalid memory is accessed.
Fix these issues by throwing error during these cases.
Fixes: 4cc9bd8d7b (ASoc: tas2783A: Add soundwire based codec driver)
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Closes: https://lore.kernel.org/r/202510291226.2R3fbYNh-lkp@intel.com/
Signed-off-by: Niranjan H Y <niranjan.hy@ti.com>
Link: https://patch.msgid.link/20251030151637.566-1-niranjan.hy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The bus_find_device_by_name() function returns a device pointer with an
incremented reference count, but the original code was missing put_device()
calls in some return paths, leading to reference count leaks.
Fix this by ensuring put_device() is called before function exit after
bus_find_device_by_name() succeeds
This follows the same pattern used elsewhere in the kernel where
bus_find_device_by_name() is properly paired with put_device().
Found via static analysis and code review.
Fixes: 4f8ef33dd4 ("ASoC: soc_sdw_utils: skip the endpoint that doesn't present")
Cc: stable@vger.kernel.org
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://patch.msgid.link/20251029071804.8425-1-linmq006@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The probe function enables regulators at the beginning
but fails to disable them in its error handling path.
If any operation after enabling the regulators fails,
the probe will exit with an error, leaving the regulators
permanently enabled, which could lead to a resource leak.
Add a proper error handling path to call regulator_bulk_disable()
before returning an error.
Fixes: 9a397f4736 ("ASoC: cs4271: add regulator consumer support")
Signed-off-by: Haotian Zhang <vulab@iscas.ac.cn>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20251105062246.1955-1-vulab@iscas.ac.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
The SDCA specification uses Q7.8 volume format.
This patch adds a field to indicate whether it is SDCA volume control
and supports the volume settings.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20251106093335.1363237-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Component drivers can prepare snd_pcm_hardware struct based on the hardware
capabilities which information should not be discarded.
Only touch the rates, channels_max and formats if they were left to 0,
otherwise keep the provided configuration intact for the parameter cross
checking decision.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://patch.msgid.link/20251029073600.13624-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Srinivas Kandagatla <srinivas.kandagatla@oss.qualcomm.com>:
This patchset has 4 fixes and some enhancements to the Elite DSP driver
support.
Fixes includes
- setting correct flags for expected behaviour of appl_ptr
- fix closing of copp instances
- fix buffer alignment.
- fix state checks before closing asm stream
Enhancements include:
- adding q6asm_get_hw_pointer and ack callback support
- simplify code via __free(kfree) mechanism.
- use spinlock guards
- few cleanups discovered during doing above 2.
There is another set of updates comming soon, which will add support
for early memory mapping and few more modules support in audioreach.
Clean up the code using guard() for spin locks.
No functional changes, just cleanup.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@oss.qualcomm.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@oss.qualcomm.com>
Link: https://patch.msgid.link/20251023102444.88158-20-srinivas.kandagatla@oss.qualcomm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Its common pattern in q6dsp code to allocate temporary buffer
to send gpr/apr packets and free at the function exit.
Now this can be simplified via __free(kfree) mechanism.
No functional changes.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@oss.qualcomm.com>
Link: https://patch.msgid.link/20251023102444.88158-17-srinivas.kandagatla@oss.qualcomm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Its common pattern in q6dsp code to allocate temporary buffer
to send gpr/apr packets and free at the function exit.
Now this can be simplified via __free(kfree) mechanism.
No functional changes.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@oss.qualcomm.com>
Link: https://patch.msgid.link/20251023102444.88158-16-srinivas.kandagatla@oss.qualcomm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Its common pattern in q6dsp code to allocate temporary buffer
to send gpr/apr packets and free at the function exit.
Now this can be simplified via __free(kfree) mechanism.
No functional changes.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@oss.qualcomm.com>
Link: https://patch.msgid.link/20251023102444.88158-15-srinivas.kandagatla@oss.qualcomm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Its common pattern in q6dsp code to allocate temporary buffer
to send gpr/apr packets and free at the function exit.
Now this can be simplified via __free(kfree) mechanism.
No functional changes.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@oss.qualcomm.com>
Link: https://patch.msgid.link/20251023102444.88158-14-srinivas.kandagatla@oss.qualcomm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Its common pattern in q6dsp code to allocate temporary buffer
to send gpr/apr packets and free at the function exit.
Now this can be simplified via __free(kfree) mechanism.
No functional changes.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@oss.qualcomm.com>
Link: https://patch.msgid.link/20251023102444.88158-13-srinivas.kandagatla@oss.qualcomm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Its common pattern in q6dsp code to allocate temporary buffer
to send gpr/apr packets and free at the function exit.
Now this can be simplified via __free(kfree) mechanism.
No functional changes.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@oss.qualcomm.com>
Link: https://patch.msgid.link/20251023102444.88158-12-srinivas.kandagatla@oss.qualcomm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Both capture and playback can have different runtimes, so set them
accordingly.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@oss.qualcomm.com>
Tested-by: Alexey Klimov <alexey.klimov@linaro.org> # RB5, RB3
Link: https://patch.msgid.link/20251023102444.88158-10-srinivas.kandagatla@oss.qualcomm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
make use of q6asm_get_hw_pointer to get the current hardware read/write
pointer and remove any additional code that does calculate this manually.
As this is redundant and prone to errors.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@oss.qualcomm.com>
Tested-by: Alexey Klimov <alexey.klimov@linaro.org> # RB5, RB3
Link: https://patch.msgid.link/20251023102444.88158-9-srinivas.kandagatla@oss.qualcomm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently q6asm-dai is performing an extra layer of calculation on the hw_ptr,
which is always prone to errors and redundant.
q6asm already has tokens to indentify the pointer pointers which an be
used to get the hw_ptr and this is more accurate then doing the
artificial calculation at upper layers.
Add helper function q6asm_get_hw_pointer() to get this hw_ptr.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@oss.qualcomm.com>
Tested-by: Alexey Klimov <alexey.klimov@linaro.org> # RB5, RB3
Link: https://patch.msgid.link/20251023102444.88158-8-srinivas.kandagatla@oss.qualcomm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
With the existing code, we are only setting up one period at a time, in a
ping-pong buffer style. This triggers lot of underruns in the dsp
leading to jitter noise during audio playback.
Fix this by scheduling all available periods, this will ensure that the dsp
has enough buffer feed and ultimatley fixing the underruns and audio distortion.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@oss.qualcomm.com>
Tested-by: Alexey Klimov <alexey.klimov@linaro.org> # RB5, RB3
Link: https://patch.msgid.link/20251023102444.88158-7-srinivas.kandagatla@oss.qualcomm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
For record path, multiple read requests are queued to dsp in advance.
However when data stream is closed, the pending read requests are rejected
by the dsp and a response is sent to the driver, this case is not handled
in the driver resulting in errors like below
q6asm-dai ab00000.remoteproc:glink-edge:apr:service@7:dais: command[0x10dac] not expecting rsp
q6asm-dai ab00000.remoteproc:glink-edge:apr:service@7:dais: command[0x10dac] not expecting rsp
q6asm-dai ab00000.remoteproc:glink-edge:apr:service@7:dais: command[0x10dac] not expecting rsp
This is same for both write and eos.
Fix this by allowing ASM_DATA_CMD_READ_V2, ASM_DATA_CMD_EOS and
ASM_DATA_CMD_WRITE_V2 as expected response.
Reported-by: Martino Facchin <m.facchin@arduino.cc>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@oss.qualcomm.com>
Tested-by: Alexey Klimov <alexey.klimov@linaro.org> # RB5, RB3
Link: https://patch.msgid.link/20251023102444.88158-6-srinivas.kandagatla@oss.qualcomm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Do not stop a q6asm stream if its not started, this can result in
unnecessary dsp command which will timeout anyway something like below:
q6asm-dai ab00000.remoteproc:glink-edge:apr:service@7:dais: CMD 10bcd timeout
Fix this by correctly checking the state.
Fixes: 2a9e92d371 ("ASoC: qdsp6: q6asm: Add q6asm dai driver")
Cc: Stable@vger.kernel.org
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@oss.qualcomm.com>
Tested-by: Alexey Klimov <alexey.klimov@linaro.org> # RB5, RB3
Link: https://patch.msgid.link/20251023102444.88158-5-srinivas.kandagatla@oss.qualcomm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
DSP expects the periods to be aligned to fragment sizes, currently
setting up to hw constriants on periods bytes is not going to work
correctly as we can endup with periods sizes aligned to 32 bytes however
not aligned to fragment size.
Update the constriants to use fragment size, and also set at step of
10ms for period size to accommodate DSP requirements of 10ms latency.
Fixes: 2a9e92d371 ("ASoC: qdsp6: q6asm: Add q6asm dai driver")
Cc: Stable@vger.kernel.org
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@oss.qualcomm.com>
Tested-by: Alexey Klimov <alexey.klimov@linaro.org> # RB5, RB3
Link: https://patch.msgid.link/20251023102444.88158-4-srinivas.kandagatla@oss.qualcomm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A matching Common object post processing instance is normally resused
across multiple streams. However currently we close this on DSP
even though there is a refcount on this copp object, this can result in
below error.
q6routing ab00000.remoteproc:glink-edge:apr:service@8:routing: Found Matching Copp 0x0
qcom-q6adm aprsvc:service:4:8: cmd = 0x10325 return error = 0x2
q6routing ab00000.remoteproc:glink-edge:apr:service@8:routing: DSP returned error[2]
q6routing ab00000.remoteproc:glink-edge:apr:service@8:routing: Found Matching Copp 0x0
qcom-q6adm aprsvc:service:4:8: cmd = 0x10325 return error = 0x2
q6routing ab00000.remoteproc:glink-edge:apr:service@8:routing: DSP returned error[2]
qcom-q6adm aprsvc:service:4:8: cmd = 0x10327 return error = 0x2
qcom-q6adm aprsvc:service:4:8: DSP returned error[2]
qcom-q6adm aprsvc:service:4:8: Failed to close copp -22
qcom-q6adm aprsvc:service:4:8: cmd = 0x10327 return error = 0x2
qcom-q6adm aprsvc:service:4:8: DSP returned error[2]
qcom-q6adm aprsvc:service:4:8: Failed to close copp -22
Fix this by addressing moving the adm_close to copp_kref destructor
callback.
Fixes: 7b20b2be51 ("ASoC: qdsp6: q6adm: Add q6adm driver")
Cc: Stable@vger.kernel.org
Reported-by: Martino Facchin <m.facchin@arduino.cc>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@oss.qualcomm.com>
Tested-by: Alexey Klimov <alexey.klimov@linaro.org> # RB5, RB3
Link: https://patch.msgid.link/20251023102444.88158-3-srinivas.kandagatla@oss.qualcomm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Driver does not expect the appl_ptr to move backward and requires
explict sync. Make sure that the userspace does not do appl_ptr rewinds
by specifying the correct flags in pcm_info.
Without this patch, the result could be a forever loop as current logic assumes
that appl_ptr can only move forward.
Fixes: 3d4a4411aa ("ASoC: q6apm-dai: schedule all available frames to avoid dsp under-runs")
Cc: Stable@vger.kernel.org
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@oss.qualcomm.com>
Tested-by: Alexey Klimov <alexey.klimov@linaro.org> # RB5, RB3
Link: https://patch.msgid.link/20251023102444.88158-2-srinivas.kandagatla@oss.qualcomm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
convert the Texas Instruments PCM186x Universal audio ADC bindings
to DT schema.
The PCM186x codec provides a single digital audio interface. Therefore
this binding adds a reference to dai-common.yaml and defines
'#sound-dai-cells = 0".
Signed-off-by: Ranganath V N <vnranganath.20@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20251104-dtbs-v7-1-224aacb09671@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
TAS5822 is in same family with TAS58XX.
Signed-off-by: Baojun Xu <baojun.xu@ti.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20251104041314.792-2-baojun.xu@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
