The ALSA PCM callbacks store the driver state in pcm->private_data. An
open PCM file can outlive USB disconnect because usbtv_audio_free() uses
snd_card_free_when_closed(). The disconnect path can then drop the V4L2
device reference and free struct usbtv before ALSA releases the substream,
so a later close dereferences freed memory in snd_usbtv_pcm_close().
Take a V4L2 device reference for the ALSA card and drop it from the card
private_free callback. This keeps struct usbtv valid until ALSA has closed
the remaining files and freed the card.
Closes: https://lore.kernel.org/r/178144969601.60470.4852887710381872458@gmail.com
Fixes: 63ddf68de5 ("[media] usbtv: add audio support")
Cc: stable@vger.kernel.org
Signed-off-by: Shuangpeng Bai <shuangpeng.kernel@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
kthread_run() returns an ERR_PTR on failure, not NULL.
When start_streaming() fails, data->kthread_vid_cap is left holding
this error pointer instead of being cleared.
This causes two subsequent bugs:
1. A future call to start_streaming() sees a non-NULL kthread_vid_cap
and returns 0 (success) immediately, without actually starting the
capture thread.
2. A call to stop_streaming() checks 'kthread_vid_cap == NULL' which
is false for an error pointer, and proceeds to call kthread_stop()
on the error pointer, leading to a kernel crash.
Fix this by resetting kthread_vid_cap to NULL on failure before
jumping to the error path.
Fixes: 5cebaac609 ("media: video-i2c: add video-i2c driver")
Cc: stable@vger.kernel.org
Signed-off-by: Uday Khare <udaykhare77@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
The Monoprice 106456 (board rev TV22AD-A, also sold as the AnyTV
AUTV002) is a USB ATSC/QAM tuner that enumerates as 05e1:0400 and
reports itself as a "Syntek Semiconductor USB 2.0 Video Capture
Controller". The hardware is an Auvitek AU0828A bridge with an AU8522
demodulator and an NXP TDA18271HDC2 tuner at I2C address 0x60 -- the
same demod/tuner combination as the existing Hauppauge Woodbury board.
Adds board profile and the USB ID so the device binds. The digital
frontend is electrically identical to the Woodbury, so share that
board's au8522/tda18271 configuration and attach path rather than
duplicating it. Tested with over-the-air 8VSB ATSC: it locks and
streams a live 720p transport stream.
Some 05e1:0400 units reportedly ship a Microtune MT2131 tuner with an
AU8502 demodulator instead. This patch does not handle that variant,
but it can't regress it either: 05e1:0400 matches no driver today, and
on the MT2131 units tda18271_attach() just fails, so no frontend is
registered.
Signed-off-by: Joseph Breihan <linux@josephbreihan.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
dcmipp_runtime_resume() can fail while preparing the device clocks, but
dcmipp_resume() currently ignores the result of
pm_runtime_force_resume() and always returns success.
Return the pm_runtime_force_resume() result so system resume does not
hide a failed runtime resume.
Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
dcmi_runtime_resume() returns clock enable failures, but dcmi_resume()
currently ignores the result of pm_runtime_force_resume() and always
returns success.
Return the pm_runtime_force_resume() result so system resume does not
hide a failed runtime resume.
Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
When a device with has_dual_ts=1 is probed and the is_audio_only path
is taken, both dev and dev->dev_next are added to the global
em28xx_devlist via em28xx_init_extension(). However, during disconnect,
em28xx_close_extension(dev) only calls list_del(&dev->devlist), leaving
dev->dev_next->devlist still linked in the global list. When dev_next is
subsequently freed via kref_put(), its devlist entry becomes a dangling
pointer in em28xx_devlist. The next device probe that calls
em28xx_init_extension() triggers a list corruption BUG when list_add_tail
detects the freed node.
This bug was exposed by commit a368ecde8a ("USB: core: Fix duplicate
endpoint bug by clearing reserved bits in the descriptor") which clears
reserved bits in bEndpointAddress during endpoint parsing. This causes
fuzzed endpoint addresses like 0xf3 to be normalized to 0x83, which
em28xx interprets as a vendor audio endpoint, enabling the
is_audio_only + has_dual_ts code path that was previously unreachable
with such descriptors.
Fix this by removing dev->dev_next->devlist from the global list in
em28xx_close_extension() before the device is freed.
Fixes: f410b4093f ("media: em28xx: split up em28xx_dvb_init to reduce stack size")
Cc: stable@vger.kernel.org
Reported-by: syzbot+99d6c66dbbc484f50e1c@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=99d6c66dbbc484f50e1c
Signed-off-by: Jiangong.Han <jiangong.han@windriver.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
The byte-alignment paths can call CODE_ADD() with a zero bit
length. The macro then shifts an int by name.b, which can be 32
after the preceding bit was flushed.
vti_bitlen() can likewise shift a signed int into its sign bit while
searching for the bit length, and the package mask construction can
shift by the full type width.
Make zero-length additions a no-op, derive the bit length with fls(),
and build the mask with GENMASK().
Signed-off-by: Yousef Alhouseen <alhouseenyousef@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
compress_sliced_buf() scans one byte at a time while testing a four-byte
VBI start code. The final iterations can read beyond the remaining
buffer tail.
Stop the scan once fewer than four bytes remain.
Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
compress_sliced_buf() scans one byte at a time while testing a four-byte
VBI start code. The final iterations can read beyond the remaining
buffer tail.
Stop the scan once fewer than four bytes remain.
Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Some pci_device_id arrays already used the PCI_DEVICE macros, others
used named initializers or list initializers. Unify all to use the
PCI_DEVICE macros and (if applicable) a named initializer for
.driver_data. Also drop all zeros that the compiler can care for and
unify indention and spacing.
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
The existing tegra_vi_graph_build function relies heavily on a one-to-one
match between Device Tree nodes and media pad links. While this works for
simpler configurations, it causes issues when Device Tree nodes do not
match media pad link logic (e.g., mt9m114). Switch to the
media_entity_get_fwnode_pad helper to verify and retrieve the correct pad
linked to an endpoint, rather than assuming the endpoint ID matches the
pad ID.
Tested-by: Luca Ceresoli <luca.ceresoli@bootlin.com> # tegra20, parallel camera
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
The driver uses several symbols and structs defined in that header. The
header is currently included transitively via
"vip.h" ->
<media/v4l2-ctrls.h> ->
<media/media-request.h> ->
<media/media-device.h> ->
<linux/platform_device.h>
which seems to be on the lower end of the scale between random and
reliable.
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
The av7110_start_feed function contains heavily nested if-statements,
causing excessive indentation and violating code style guidelines.
Refactor the logic inside the DMX_MEMORY_FE case by inverting the
conditional check to break early. Additionally, remove the inner
'if (feed->ts_type & TS_DECODER)' check, as it is redundant since
the outer block already validates this condition.
This reduces the indentation level and cleans up redundant checks
without altering the underlying driver behavior.
Signed-off-by: André Moreira <andrem.33333@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
All the information for the mode is now stored within
the subdev state, so configure the sensor based on that.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
The subdev state is now preferred rather than handling crop
and format within the driver state, so switch the driver to
using it.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
The sensor supports 2 or 4 lane readout, but the driver only allowed
for 4 lanes. Add 2 lane support.
The clock tree only supports single PLL mode to feed both IOP (MIPI)
and IVT (Pixel array).
2 lane mode supports a MIPI link frequency of up to 445MHz (890Mbit/s)
cf 360MHz (720Mbit/s) for 4lane. Update clock setup and pixel rates to
match.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
In preparation for additional options in the PLL setup, compute
the link frequency rather than using a hardcoded value.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
This avoids the set_ctrl handler being called under any
circumstances, as it will return an error for the unhandled
ctrl.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
The difference between frame length and max exposure time in
lines is 10. That had been used as a bare value in calculations.
Move it to a define, and use that define.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
The colorspace fields were left set to 0 when they should be
set appropriately for a raw image sensor. Add those values.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Use the new comon CCI register access helpers to replace the private
register access helpers in the imx355 driver.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Avoid powering the sensor up and down unnecessarily by using
pm_runtime's autosuspend_delay feature.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Provide all the cropping information via get_selection.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
fll_min (Frame Length Lines) is set to the same value as fll_def
for all modes, which makes it redundant.
The actual value is also erroneous as the sensor works in all
the defined modes with FLL set at the mode height + 20 lines,
so set the vblank control minimum to 20 rather than varying it.
This also improves the maximum frame rate achievable.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
The pixel rate is always the same, so there is no need to try and
recompute it in imx355_set_pad_format, and then no need to have the
pointer to it stored.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
The link_freq_index value in imx355_mode is unused, so remove it.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Compute the binning registers based on the difference between
the mode width/height vs the crop width/height.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
The driver already has the LLP value stored in the mode structure,
but also had the same value set via register writes in the mode's
register list. Remove this duplication.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Currently the cropping is set via register entries in the per mode
register lists. Add the crop information to the mode structure as
a v4l2_rect, and set the registers programmatically.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Registers 0x0340 and 0x0341 (FRM_LENGTH_LINES) are already written
from the set_ctrl(V4L2_CID_VBLANK) handler, so don't write them
from the mode register list.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
A large number of registers are identical within all the modes.
Move those to imx355_global_regs.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
The sensor supports output over either 2 or 4 CSI2 data
lanes. The binding only permitted the 4 lane configuration.
Add the 2 lane configuration as an option.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
The IMX355 sensor supports multiple external clock frequencies,
including 19.2 MHz and 24 MHz. The driver currently supports only
fixed 19.2 MHz input clock.
Refactor the clock handling to make the PLL configuration dependent
on the external clock frequency and add support for 24 MHz. Introduce
a table of clock parameter sets and program the corresponding EXTCLK
frequency and PLL multipliers to maintain consistent internal VCO
frequencies across supported inputs.
The PLL settings are adjusted so that OP VCO remains at 720 MHz
This preserves existing timing characteristics while allowing systems
using a 24 MHz clock to operate correctly.
No functional change for existing 19.2 MHz users.
Assisted-by: Claude:claude-opus-4-6
Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
If v4l2_async_register_subdev_sensor failed, then the sensor had
already been powered down by pm_runtime_idle, but the error path
then also explicitly called imx355_power_off as well. That left
an imbalance in the regulator and clock calls.
Call pm_runtime_idle only after v4l2_async_register_subdev_sensor
succeeds to avoid this.
Fixes: efa5fe19c0 ("media: imx355: Enable runtime PM before registering async sub-device")
Cc: stable@vger.kernel.org
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
vd55g4 is the same device as vd65g4 but outputs in monochrome instead of
RGB. Adapt the driver structure according to this new variant, and add
its support.
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Define it as a new monochrome variant of vd65g4.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Apply digital gain to all channels, each channel representing a color.
Cc: stable@vger.kernel.org
Fixes: e138e7f000 ("media: i2c: vd55g1: Add support for vd65g4 RGB variant")
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
vd55g1_update_pad_fmt() is called in vd55g1_init_state(). But
vd55g1_set_pad_fmt(), called at the end of vd55g1_init_state(), also
calls vd55g1_update_pad_fmt() itself.
Enhance readability and clear confusion by only preparing the format in
vd55g1_init_state() and let vd55g1_set_pad_fmt() update it instead,
effectively calling it only 1 time instead of 2.
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
In the driver initialization, the index of the default media bus code
from the supported media bus code array is passed directly to the
vd55g1_get_fmt_code() function instead of the proper media bus code.
This works correctly as a proper media bus code is set after
initialization but could not have been the case. This also resulted in
mutliple "Unsupported mbus format" error messages.
Retrieve the media bus code from the media bus code array, and pass this
media bus code to vd55g1_get_fmt_code() instead of the code index.
Rename VD55G1_MBUS_CODE_DEF to VD55G1_MBUS_CODE_IDX_DEF and
VD55G1_MODE_DEF to VD55G1_MODE_IDX_DEF while at it to avoid future
confusions. Display the guilty error code in warning message.
Cc: stable@vger.kernel.org
Fixes: e138e7f000 ("media: i2c: vd55g1: Add support for vd65g4 RGB variant")
Signed-off-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
ipu6_bus_initialize_device() stores the isys/psys pdata pointer in
struct ipu6_bus_device and initializes the auxiliary device. After that
point, error unwinding must drop the auxiliary device reference and let
ipu6_bus_release() free both the bus device and adev->pdata.
The isys and psys init paths already call put_device() when MMU
initialization fails, and ipu6_bus_add_device() calls
auxiliary_device_uninit() on auxiliary_device_add() failure. Both paths
therefore run the bus release callback. The extra kfree(pdata) in the
callers can release the same object a second time.
Remove the manual pdata frees after the auxiliary device has been
initialized.
This issue was found by a static analysis checker and confirmed by
manual source review.
Fixes: cb3117b074 ("media: intel/ipu6: add IPU auxiliary devices")
Signed-off-by: Ruoyu Wang <ruoyuw560@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
The sensor registers are only written in the runtime PM resume
handler; ov8865_set_fmt() merely stores the requested mode, relying on
the sensor being runtime suspended between uses so that the next
resume applies it.
That assumption breaks when something keeps the sensor powered. On
IPU3 platforms, ipu_bridge instantiates the VCM device with a
DL_FLAG_PM_RUNTIME device link to the sensor, so a userspace process
holding the VCM subdev open (e.g. wireplumber's camera monitor) pins
the sensor runtime-active. A subsequent set_fmt() then never reaches
the hardware: the sensor keeps streaming the mode programmed on the
last resume while the CSI-2 receiver expects the newly negotiated
format.
On a Surface Book 2 (IPU3, ov8865 + dw9719 VCM), requesting the
3264x2448 mode while the hardware was left programmed for the
1632x1224 binned mode makes ipu3-cio2 report "frame sync error" and
"payload length is 10340352, received 2585088" (exactly one binned
frame) for every frame, and the inverse case stalls the stream after
a single frame. Camera applications end up displaying one bogus frame
forever.
Program the sensor configuration and apply the control values on
stream start instead, where the negotiated mode is always current,
and only write the configuration in the runtime PM resume handler
when resuming with the stream already started.
Signed-off-by: Jurison Murati <eng.juri@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
ov8865_s_stream() takes a runtime PM reference when enabling the
stream, but returns without releasing it if ov8865_sw_standby()
fails, leaving the reference unbalanced and the sensor powered
indefinitely. The same applies to a failure while disabling the
stream, in which case the reference acquired at stream start is
never dropped.
Drop the reference in a single place, both when disabling the
stream and on failure, and only update the streaming state on
success.
Signed-off-by: Jurison Murati <eng.juri@gmail.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Add a blank line between the local variable declarations and
the following statement in ipu_bridge_get_ivsc_acpi_dev().
Also remove an unnecessary blank line within the declaration block.
This addresses a checkpatch.pl warning.
No functional change intended.
Signed-off-by: Hungyu Lin <dennylin0707@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Several camera sensor drivers access the "clock-frequency" property
directly to retrieve the external clock rate or handle the external
clock manually in the driver. While this is valid on a subset of ACPI
platforms, implementing this logic directly in drivers is deprecated
and can lead to inconsistent behaviour across drivers.
This driver supports ACPI platforms only. It currently retrieves the
external clock rate from the "clock-frequency" property and fails
probing if the rate does not match the expected value, which is the
correct policy for ACPI platforms.
Switch to using the devm_v4l2_sensor_clk_get() helper to standardise
clock handling. This preserves the existing behaviour on ACPI
platforms that specify a clock-frequency property without providing
a clock. On platforms that provide a clock, the helper will program
the clock to the rate specified by clock-frequency, which is also
consistent with the driver's expectations.
Reviewed-by: Hans de Goede <johannes.goede@oss.qualcomm.com>
Signed-off-by: Sanjay Chitroda <sanjayembeddedse@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Currently, VIDEO_AMD_ISP4_CAPTURE selects VIDEO_V4L2_SUBDEV_API without
ensuring MEDIA_CONTROLLER is enabled, causing an unmet dependency:
WARNING: unmet direct dependencies detected for VIDEO_V4L2_SUBDEV_API
Depends on [n]: MEDIA_SUPPORT [=m] && VIDEO_DEV [=m] && MEDIA_CONTROLLER [=n]
Selected by [m]:
- VIDEO_AMD_ISP4_CAPTURE [=m] && MEDIA_SUPPORT [=m] && MEDIA_PLATFORM_SUPPORT [=y] && MEDIA_PLATFORM_DRIVERS [=y] && DRM_AMDGPU [=m] && DRM_AMD_ISP [=y] && HAS_DMA [=y] && VIDEO_DEV [=m]
Many other options in this subsystem select MEDIA_CONTROLLER, let's do the
same here.
This unmet dependency bug was detected by kconfirm, a static analysis tool
for Kconfig.
Fixes: 9a54c28563 ("media: platform: amd: Introduce amd isp4 capture driver")
Signed-off-by: Julian Braha <julianbraha@gmail.com>
Reviewed-by: Bin Du <bin.du@amd.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
In v4l2_fwnode_parse_link(), the remote endpoint fwnode reference is
acquired using fwnode_graph_get_remote_endpoint(). This reference is
properly released in the error paths, but it is leaked on the success
path.
Add the missing fwnode_handle_put() before returning 0 to prevent the
reference leak.
Signed-off-by: Biren Pandya <birenpandya@gmail.com>
Fixes: ca50c197bd ("[media] v4l: fwnode: Support generic fwnode for parsing standardised properties")
Cc: stable@vger.kernel.org
[Sakari Ailus: Fix subject prefix and coding style a little.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
The driver misses calling media_entity_cleanup() on the probe error path
and during remove, leaking resources if probe fails after entity
initialization or when the driver is unloaded.
Fix this by adding media_entity_cleanup() to the rdacm21_probe() error
handling path and to rdacm21_remove().
Fixes: a59f853b3b ("media: i2c: Add driver for RDACM21 camera module")
Signed-off-by: Biren Pandya <birenpandya@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
The Dell 16 Premium DA16250 (marketed as XPS 16) has its OV02C10 front
sensor mounted upside down, like the other Dell XPS models already present
in upside_down_sensor_dmi_ids[]. The rotation is reported as 0 in both the
SSDB and the _PLD, so without a DMI quirk the image is presented upside
down.
Add a DMI quirk entry for this model so that a rotation of 180 degrees is
reported for its OVTI02C1 sensor.
Signed-off-by: Samuele Angioli <samuele.angioli@inspect.it>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
The VIP driver uses v4l2_fwnode_endpoint_parse() and the
v4l2_async_nf_*() notifier APIs, but its Kconfig entry does not
select V4L2_FWNODE. Hence kernel test robot reports:
vip.c:3236: undefined reference to `v4l2_async_nf_unregister'
vip.c:3237: undefined reference to `v4l2_async_nf_cleanup'
vip.c:3339: undefined reference to `v4l2_fwnode_endpoint_parse'
vip.c:3346: undefined reference to `v4l2_async_nf_init'
vip.c:3348: undefined reference to `__v4l2_async_nf_add_fwnode'
vip.c:3357: undefined reference to `v4l2_async_nf_register'
Select V4L2_FWNODE, which in turn selects V4L2_ASYNC, providing
all the missing symbols.
Fixes: fc2873aa4a ("media: ti: vpe: Add the VIP driver")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202607031826.vOPABT39-lkp@intel.com/
Signed-off-by: Yemike Abhilash Chandra <y-abhilashchandra@ti.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
