Apparently some BXT/GLK systems have DSI panels whose timings
don't agree with the normal cpu transcoder hblank>=32 limitation.
This is perhaps fine as there are no specific hblank/etc. limits
listed for the BXT/GLK DSI transcoders.
Move those checks out from the global intel_mode_valid() into
into connector specific .mode_valid() hooks, skipping BXT/GLK
DSI connectors. We'll leave the basic [hv]display/[hv]total
checks in intel_mode_valid() as those seem like sensible upper
limits regardless of the transcoder used.
Cc: stable@vger.kernel.org
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/9720
Fixes: 8f4b1068e7 ("drm/i915: Check some transcoder timing minimum limits")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231127145028.4899-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Currently no one can figure out what the PSR code is doing since
we're including any of it in the basic state dump. Add at least the
bare minimum there.
v2: Also dump has_panel_replay (Jouni)
Cc: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231124082735.25470-1-ville.syrjala@linux.intel.com
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
In earlier versions, FBC was restricted if PSR2 is enabled. From
xe2lpd onwards no such restrictions are needed anymore.
HSD: 14014305387
Signed-off-by: Vinod Govindapillai <vinod.govindapillai@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231110093225.39573-2-vinod.govindapillai@intel.com
Currently we are enabling selective fetch for all planes that are visible.
This is suboptimal as we might be fetching for memory for planes that are
not part of selective update.
Fix this by adding proper handling for disabling plane selective fetch:
If plane previously part of selective update is now not part of update:
Add it into updated planes and let the plane configuration to disable
selective fetch for it.
v3: Checkpatch warnings fixed
v2:
- Add setting sel_fetch_area->y1/y2 to -1
- Remove setting again local sel_fetch_area variable
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231120082606.3156488-3-jouni.hogander@intel.com
Currently selective fetch configuration for planes is implemented in psr
code. More suitable place for this code is where everything else is
configured for planes -> move it into skl_universal_plane.c and
intel_cursor.c. This also allows us to drop hooks for cursor handling.
v3: Checkpatch warnings fixed
v2: Removed setting sel_fetch_area->y1/y2 as -1
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231120082606.3156488-2-jouni.hogander@intel.com
The current implementation of change_lut_val_precision() is just
a convoluted way of shifting by 8. Implement the proper rounding
by just using drm_color_lut_extract() and intel_color_lut_pack()
like everyone else does.
And as the uapi can't handle >=1.0 values but the hardware
can we need to clamp the results appropriately in the readout
path.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231013131402.24072-5-ville.syrjala@linux.intel.com
Reviewed-by: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
drm_color_lut_extract() rounding was changed to follow the
OpenGL int<->float conversion rules. Adjust intel_color_lut_pack()
to match.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231013131402.24072-3-ville.syrjala@linux.intel.com
Reviewed-by: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
The current implementation of drm_color_lut_extract()
generates weird results. Eg. if we go through all the
values for 16->8bpc conversion we see the following pattern:
in out (count)
0 - 7f -> 0 (128)
80 - 17f -> 1 (256)
180 - 27f -> 2 (256)
280 - 37f -> 3 (256)
...
fb80 - fc7f -> fc (256)
fc80 - fd7f -> fd (256)
fd80 - fe7f -> fe (256)
fe80 - ffff -> ff (384)
So less values map to 0 and more values map 0xff, which
doesn't seem particularly great.
To get just the same number of input values to map to
the same output values we'd just need to drop the rounding
entrirely. But perhaps a better idea would be to follow the
OpenGL int<->float conversion rules, in which case we get
the following results:
in out (count)
0 - 80 -> 0 (129)
81 - 181 -> 1 (257)
182 - 282 -> 2 (257)
283 - 383 -> 3 (257)
...
fc7c - fd7c -> fc (257)
fd7d - fe7d -> fd (257)
fe7e - ff7e -> fe (257)
ff7f - ffff -> ff (129)
Note that since the divisor is constant the compiler
is able to optimize away the integer division in most
cases. The only exception is the _ULL() case on 32bit
architectures since that gets emitted as inline asm
via do_div() and thus the compiler doesn't get to
optimize it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231013131402.24072-2-ville.syrjala@linux.intel.com
Reviewed-by: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
We are preparing for Xe driver. I915 and Xe object implementation are
differing. Use intel_bo_to_drm_bo instead of &obj->base.
Signed-off-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231116150225.204233-3-juhapekka.heikkila@gmail.com
There's no real reason why we'd need a full modeset for audio
changes. So let's allow audio to be toggled during fastset.
In case the ELD changes while has_audio isn't changing state
we force both audio disable and enable so the new ELD gets
propagated to the audio driver.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231121054324.9988-12-ville.syrjala@linux.intel.com
Add encoder vfuncs for audio enable/disable. This will allow
audio to be enabled/disabled during fastsets. An encoder hook
is necessary as on pre-hsw platforms different encoder types
implement audio in different ways.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231121054324.9988-9-ville.syrjala@linux.intel.com
Follow the hsw+ approach toggle the audio presence detect
when we set up the ELD, instead of doing it when turning the
port on/off.
This will facilitate audio enable/disable to happen during
fastsets instead of requiring a full modeset.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231121054324.9988-8-ville.syrjala@linux.intel.com
Follow the hsw+ approach toggle the audio presence detect
when we set up the ELD, instead of doing it when turning the
port on/off.
This will facilitate audio enable/disable to happen during
fastsets instead of requiring a full modeset.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231121054324.9988-7-ville.syrjala@linux.intel.com
Push the audio enable/disable to be the last/first thing
respectively that is done in the encoder enable/disable hooks.
The goal is to move it further out of these encoder hooks entirely.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231121054324.9988-5-ville.syrjala@linux.intel.com
We used to call intel_pre_plane_updates() for any pipe going through
a modeset whether the pipe was previously enabled or not. This in
fact needed to apply all the necessary clock gating workarounds/etc.
Restore the correct behaviour.
Fixes: 3991999732 ("drm/i915: Disable all planes before modesetting any pipes")
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231121054324.9988-3-ville.syrjala@linux.intel.com
{planes,vrr}_{enabling,disabling}() are supposed to indicate
whether the specific hardware feature is supposed to be enabling
or disabling. That can only makes sense if the pipe is active
overall. So check for that before we go poking at the hardware.
I think we're semi-safe currently on due to:
- intel_pre_plane_update() doesn't get called when the pipe
was not-active prior to the commit, but this is actually a bug.
This saves vrr_disabling(), and vrr_enabling() is called from
deeper down where we have already checked hw.active.
- active_planes mirrors the crtc's hw.active
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231121054324.9988-2-ville.syrjala@linux.intel.com
entry_setup_frames variable is defined as u8. However, the
function call intel_psr_entry_setup_frames() can return
negative error code. There is a type mismatch here, so let's
switch to use int here as well.
Fixes: 2b981d57e4 ("drm/i915/display: Support PSR entry VSC packet to be transmitted one frame earlier")
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Vinod Govindapillai <vinod.govindapillai@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231116090512.480373-1-mika.kahola@intel.com
Drop unused vlv_iosf_sb_read() and vlv_iosf_sb_write().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231103201831.1037416-17-andriy.shevchenko@linux.intel.com
For a couple of cases the branches call the same bxt_gpio_set_value().
As Ville suggested they can be combined by dropping the DISPLAY_VER()
check from Gen 11 to Gen 9. Do it that way.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231103201831.1037416-16-andriy.shevchenko@linux.intel.com
It's a dirty hack in the driver that pokes GPIO registers behind
the driver's back. Moreoever it might be problematic as simultaneous
I/O may hang the system, see the commit 0bd50d719b ("pinctrl:
cherryview: prevent concurrent access to GPIO controllers") for
the details. Taking all this into consideration replace the hack
with proper GPIO APIs being used.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231103201831.1037416-15-andriy.shevchenko@linux.intel.com
Currently soc_gpio_set_value() supports only a single indexing for GPIO
pin. For CHV case, for example, we will need to distinguish community
based index from the one that VBT is using. Introduce an additional
parameter to soc_gpio_set_value() and its callers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231103201831.1037416-14-andriy.shevchenko@linux.intel.com
It's a dirty hack in the driver that pokes GPIO registers behind
the driver's back. Moreoever it might be problematic as simultaneous
I/O may hang the system, see the commit 40ecab5512 ("pinctrl:
baytrail: Really serialize all register accesses") for the details.
Taking all this into consideration replace the hack with proper
GPIO APIs being used.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231103201831.1037416-13-andriy.shevchenko@linux.intel.com
Extract a common soc_gpio_set_value() helper that may be used by a few
SoCs.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231103201831.1037416-12-andriy.shevchenko@linux.intel.com
Fix wrong initial value for GPIOs in bxt_gpio_set_value().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231103201831.1037416-11-andriy.shevchenko@linux.intel.com
To properly deal with GPIOs used in MIPI panel sequences a temporary
GPIO lookup will be used. Since there can only be 1 GPIO lookup table
for the "0000:00:02.0" device this will not work if the GPIO lookup
table used by intel_dsi_vbt_gpio_init() is still registered.
After getting the "backlight" and "panel" GPIOs the lookup table
registered by intel_dsi_vbt_gpio_init() is no longer necessary,
remove it so that another temporary lookup-table for the "0000:00:02.0"
device can be added.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231103201831.1037416-10-andriy.shevchenko@linux.intel.com
Names of the MIPI sequence steps are sequential and defined, no
need to check for the gaps. However in seq_name the MIPI_SEQ_END
is missing. Add it there, and drop unneeded NULL check in
sequence_name().
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231103201831.1037416-9-andriy.shevchenko@linux.intel.com
In the snippets like the following
if (...)
return / goto / break / continue ...;
else
...
the 'else' is redundant. Get rid of it.
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231103201831.1037416-8-andriy.shevchenko@linux.intel.com
Move existing condition to while(), so it will be clear on what
circumstances the loop is successfully finishing.
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231103201831.1037416-7-andriy.shevchenko@linux.intel.com
Drop the unused parameter.
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231103201831.1037416-6-andriy.shevchenko@linux.intel.com
The lowest level functions are about setting GPIO values, not about
executing any sequences anymore.
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231103201831.1037416-5-andriy.shevchenko@linux.intel.com
With the various sequence versions and pointer increments interleaved,
it's a bit hard to decipher what's going on. Add separate paths for
different sequence versions.
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231103201831.1037416-4-andriy.shevchenko@linux.intel.com
Follow the contemporary conventions.
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231103201831.1037416-3-andriy.shevchenko@linux.intel.com
Purely a guess. Drop the nop function.
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231103201831.1037416-2-andriy.shevchenko@linux.intel.com
Reuse intel_dp_max_data_rate() and intel_dp_effective_data_rate() in
intel_link_compute_m_n(), instead of open-coding the equivalent. Note
the kbit/sec -> kByte/sec unit change in the M/N values, but this not
reducing the precision, as the link rate value is based anyway on a less
precise 10 kbit/sec value.
Suggested-by: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231116131841.1588781-12-imre.deak@intel.com
Simplify intel_dp_max_data_rate() using
drm_dp_bw_channel_coding_efficiency() to calculate the max data rate for
both DP1.4 and UHBR link rates. This trades a redundant multiply/divide
for readability.
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231116131841.1588781-11-imre.deak@intel.com
Callers of intel_dp_max_data_rate() use the return value as an upper
bound for the BW a given mode requires. As such the rounding shouldn't
result in a bigger value than the actual upper bound. Use round-down
instead of -closest accordingly.
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231116131841.1588781-10-imre.deak@intel.com
Atm the allocated MST PBN value is calculated from the TU size (number
of allocated MTP slots) as
PBN = TU * pbn_div
pbn_div being the link BW for each MTP slot. For DP 1.4 link rates this
worked, as pbn_div there is guraranteed to be an integer number, however
on UHBR this isn't the case. To get a PBN, TU pair where TU is a
properly rounded-up value covering all the BW corresponding to PBN,
calculate first PBN and from PBN the TU value.
Calculate PBN directly from the effective pixel data rate, instead of
calculating it indirectly from the corresponding TU and pbn_div values
(which are in turn derived from the pixel data rate and BW overhead).
Add a helper function to calculate the effective data rate, also adding
a note that callers of intel_dp_link_required() may also need to check
the effective data rate (vs. the data rate w/o the BW overhead).
While at it add a note to check if WA#14013163432 is applicable.
v2:
- Fix PBN calculation, deriving it from the effective data rate directly
instead of using the indirect TU and pbn_div values for this.
- Add a note about WA#14013163432. (Arun)
v3:
- Fix rounding up quotient while calculating remote_tu. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com> (v1)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231117150929.1767227-3-imre.deak@intel.com
The next patch will calculate the PBN value directly from the pixel data
rate and the BW allocation overhead, not requiring the data, link M/N
and TU values for this. To prepare for that move the calculation of BW
overheads from intel_dp_mst_compute_m_n() to
intel_dp_mst_find_vcpi_slots_for_bpp().
While at it store link_bpp in a .4 fixed point format.
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231116131841.1588781-8-imre.deak@intel.com
The link M/N ratio is the data rate / link symbol clock rate, fix things
up accordingly. On DP 1.4 this ratio was correct as the link symbol clock
rate in that case matched the link data rate (in bytes/sec units, the
symbol size being 8 bits), however it wasn't correct for UHBR rates
where the symbol size is 32 bits.
Kudos to Arun noticing in Bspec the incorrect use of link data rate in
the ratio's N value.
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231116131841.1588781-7-imre.deak@intel.com
