Call mt9m114_ifp_update_sel_and_src_fmt() on sink pad format changes to
propagate these downstream.
This is necessary in 2 different scenarios:
1. When passing through RAW10 bypassing the scaler then any sink pad format
changes must be propagated to the crop/compose selections and to the source
pad format.
2. When the scaler is active, then the crop-rectangle cannot be bigger then
the sink pad format minus a 4 pixel border all around. If the sink format
change reduces the size then things also needs to be propagated downstream.
Rather then adding extra code to check for these conditions, simply always
propagate sink pad format changes downstream.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans de Goede <johannes.goede@oss.qualcomm.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Changing the IFP source pad format to RAW10 means disabling the scaler,
which means that the crop and compose rectangles must be reset to
match the sink format size with no border.
And when changing the source pad format back from RAW10 to another format
which require demosaicing the crop and compose rectangles must be reset
to the sink format size minus a 4 pixels border all around it.
Also when changing the source pad format back from RAW10 to another format
the colorspace, ycbcr_enc and quantization need to be updated too.
Add a new mt9m114_ifp_update_sel_and_src_fmt() helper which resets all
these taking the bordersize for the new source format into account and
call this helper whenever the source pad format changes to/from RAW10.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans de Goede <johannes.goede@oss.qualcomm.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Normally the IFP removes a 4 pixel border all around its sink format
size for demosaicing. But in RAW10 mode it does not do this.
Add a new mt9m114_ifp_get_border() helper function to get the border size
(4 or 0) and use this where applicable instead of hardcoding a border
of 4 pixels everywhere.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans de Goede <johannes.goede@oss.qualcomm.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Put the sensor back in reset on power down. Putting the sensor in reset
reduces power-consumption by putting all the data / ctrl pins in High-Z
mode. This helps save power on designs where the regulators may need to
stay on while the sensor is powered down.
This also ensures that the sensor is properly reset on power up,
since now the sensor will see a reset high to low transition after
the regulators have been turned on.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans de Goede <johannes.goede@oss.qualcomm.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
mt9m114_probe() requests the reset GPIO in output low state:
sensor->reset = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW);
and then almost immediately afterwards calls mt9m114_power_on() which does:
gpiod_set_value(sensor->reset, 1);
fsleep(duration);
gpiod_set_value(sensor->reset, 0);
which means that if the reset pin was high before this code runs that
it will very briefly be driven low because of passing GPIOD_OUT_LOW when
requesting the GPIO only to be driven high again possibly directly after
that. Such a very brief driving low of the reset pin may put the chip in
a confused state.
Request the GPIO in high (reset the chip) state instead to avoid this,
turning the initial gpiod_set_value() in mt9m114_power_on() into a no-op.
and the fsleep() ensures that it will stay high long enough to properly
reset the chip.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans de Goede <johannes.goede@oss.qualcomm.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
The PLL gets programmed to achieve a 48 MHz pixelclock, with the current
vblank + hblank defaults this results in a fps of:
48000000 / ((1296 + 307) * (976 + 23) = 29.974 fps
Tweak the defaults to get closer to 30 fps:
48000000 / ((1296 + 308) * (976 + 21) = 30.015 fps
This improves things from being 0.026 fps too low to 0.015 fps too high.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans de Goede <johannes.goede@oss.qualcomm.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
The current default hblank and vblank values are based on reaching 30 fps
with the pixel-array outputting 1280x960, but the default format for
the pixel-array source pad and the isp sink pad is 1296x976, correct
the default hblank and vblank values to take this into account.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans de Goede <johannes.goede@oss.qualcomm.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
As the comment above the defines says, the minimum values are undocumented
so the lowest values seen in register lists are used.
The version of the mt9m114 driver shipped together with the atomisp code
uses 21 for vblank in its register lists, lower MT9M114_MIN_VBLANK
accordingly.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans de Goede <johannes.goede@oss.qualcomm.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Before this change the driver used hardcoded PLL m, n and p values to
achieve a 48MHz pixclock when used with an external clock with a frequency
of 24 MHz.
Use aptina_pll_calculate() to allow the driver to work with different
external clock frequencies. The m, n, and p values will be unchanged
with a 24 MHz extclk and this has also been tested with a 19.2 MHz
clock where m gets increased from 32 to 40.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans de Goede <johannes.goede@oss.qualcomm.com>
[Sakari Ailus: Fix capitalisation of "MHz".]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Make aptina_pll_calculate() debug log the calculated p1 min and max values,
this makes it easier to see how the m, n and p1 values were chosen.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans de Goede <johannes.goede@oss.qualcomm.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
The reset GPIO must be requested in the asserted (HIGH) state to keep
the sensor in standby during probe and power sequencing.
Signed-off-by: Elgin Perumbilly <elgin.perumbilly@siliconsignals.io>
Acked-by: Tarang Raval <tarang.raval@siliconsignals.io>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Provide information on the frame layout using frame descriptors.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Julien Massot <julien.massot@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
With enable_streams and disable_streams, the driver for a device where
streams are not independently started and stopped needs to maintain state
information on streams that have been requested to be started. Do that
now.
In the future, a helper function in the framework is a desirable way to do
this instead.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Julien Massot <julien.massot@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Switch from s_stream() video op to enable_streams() and disable_streams()
pad operations. They are preferred and required for streams support.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Fix setting sub-device state for non-source sub-devices.
Fixes: 5755be5f15 ("media: v4l2-subdev: Rename .init_cfg() operation to .init_state()")
Cc: stable@vger.kernel.org # for v6.8 and later
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Configurable vertical blanking size control allows users to set a wanted
image frame rate.
Reviewed-by: Tarang Raval <tarang.raval@siliconsignals.io>
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Configurable vertical blanking size control allows users to set a wanted
image frame rate.
Reviewed-by: Tarang Raval <tarang.raval@siliconsignals.io>
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Convert binding for ti,omap3isp from TXT to YAML format.
Signed-off-by: Alex Tran <alex.t.tran@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Convert binding for toshiba,et8ek8 from TXT to YAML format.
Update MAINTAINERS file accordingly. The binding references
video-interface-devices.yaml at top level to inherit flash-leds
property.
Signed-off-by: Alex Tran <alex.t.tran@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Fix checkpatch error "trailing statements should be on next line"
by moving the return statement to a new line.
Signed-off-by: Arjun Changla <arjunchangla7@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
The memory allocation functions (kvzalloc) already emit a stack dump
on failure when GFP_KERNEL is used. Printing an extra error message
is redundant and increases code size.
This resolves the checkpatch warnings:
WARNING: Possible unnecessary 'out of memory' message
Signed-off-by: Zixuan Dong <dbeidachazi@foxmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
The link frequency can vary between modes, so add it as a control.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
The pixel rate control is marked as read-only by the framework itself,
so no need to mark it explicitly in the driver. Also, we can set the ops
to NULL to avoid checking for it in the s_ctrl implementation.
Suggested-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
In order to simplify the driver slightly, use the same PLL
configuration, and hence pixel rate and link frequency (to be
added) for the full, 1080p, and binned modes.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
There are many registers in common between all the modes.
Pull those out into one common table.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
To make comparisons of the mode registers easier, put the registers
for the binned and VGA modes in the same order as the others.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
The driver did expose V4L2_CID_HBLANK, but as a READ_ONLY control.
The sensor only uses the HTS register to control the line length,
so convert this control to read/write, with the appropriate ranges.
Adopt the old fixed values as the minimum values permitted in each
mode to avoid issues of it not streaming.
This should allow exposure times up to ~3 seconds (up from ~1sec).
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
v4l2_async_register_subdev doesn't bind in lens or flash drivers,
but v4l2_async_register_subdev_sensor does.
Switch to using v4l2_async_register_subdev_sensor.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Add missing controls for horizontal and vertical flipping.
The sensor readout mirrors in the horizontal direction by default (if
0x3821[1] = 0) which can make things unnecessarily difficult for
applications. The register table prior to this commit was setting that
bit explicitly, to achieve a normally oriented image.
Now that we have userspace controls for HFLIP, we keep the convention
and report the non-mirrored image (with 0x3821[1] = 1) as
horizontal_flip=0, and vice versa.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Co-developed-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Parse device properties and register controls for them using the V4L2
fwnode properties helpers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Allow properties from video-interface-devices. The change is identical to
commit 08fbd355be ("media: dt-bindings: sony,imx219: Allow props from
video-interface-devices")
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
The driver supported using GPIOs to control the shutdown line,
but no regulator control.
Add regulator hooks.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
The OV5647 camera sensor takes 3 voltage supplies. So define those in
the bindings as optional regulators, to not break existing users.
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
The pixel rate for VGA (640x480) mode is configured in the mode's table
to be 58.333 MPix/s instead of 55 MPix/s, so fix it.
Fixes: 911f4516ee ("media: ov5647: Support V4L2_CID_PIXEL_RATE")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/CAPY8ntA2TCf9FuB6Nk%2BOn%2By6N_PMuYPAOAr3Yx8YESwe4skWvw@mail.gmail.com/
Suggested-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
As this sensor captures RAW bayer frames, the colorspace should be
V4L2_COLORSPACE_RAW instead of SRGB.
Fixes: a8df5af695 ("media: ov5647: Add SGGBR10_1X10 modes")
Cc: stable@vger.kernel.org
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Trial and error reveals that the minimum vblank value appears to be 24
(the OV5647 data sheet does not give any clues). This fixes streaming
lock-ups in full resolution mode.
Fixes: 2512c06441 ("media: ov5647: Support V4L2_CID_VBLANK control")
Cc: stable@vger.kernel.org
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
The top offset in the pixel array is actually 6 (see page 3-1 of the
OV5647 data sheet).
Fixes: 14f70a3232 ("media: ov5647: Add support for get_selection()")
Cc: stable@vger.kernel.org
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
In ov5647_init_controls() we call v4l2_get_subdevdata, but it is
initialized by v4l2_i2c_subdev_init() in the probe, which currently
happens after init_controls(). This can result in a segfault if the
error condition is hit, and we try to access i2c_client, so fix the
order.
Fixes: 4974c2f19f ("media: ov5647: Support gain, exposure and AWB controls")
Cc: stable@vger.kernel.org
Suggested-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
ccs_validate_csi_data_format() will soon be needed elsewhere, above its
current location. Move it up.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Julien Massot <julien.massot@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
In preparation for upcoming changes in the function, rename the out label
as err_pm_put. The purpose of the label is changed to match its name in
the next patch.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Prepare for using ccs_pm_get_init from locations earlier than its the
current place.
Also add a missing newline while at it.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Streaming will have been stopped before the sensor is powered off, and so
sensor->streaming is also false already. Do not set it as part of the
runtime suspend callback.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Document that -ENXIO is returned when the user tries to set a routing
configuration not supported by the hardware (or rather the driver). The
documentation details the exact cases of this, besides -EINVAL that is
already documented for VIDIOC_SUBDEV_S_ROUTING.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
The routing flag indicating an active route is called
V4L2_SUBDEV_ROUTE_FL_ACTIVE, not V4L2_SUBDEV_STREAM_FL_ACTIVE. Fix this.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Remove DocBook (?) conversion leftovers from figure titles, including
obsolete numbering and highlighting. This aligns these titles with others.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Once an async connection is found to be matching with an fwnode, a
sub-device may be registered (in case it wasn't already), its bound
operation is called, ancillary links are created, the async connection
is added to the sub-device's list of connections and removed from the
global waiting connection list. Further on, the sub-device's possible own
notifier is searched for possible additional matches.
Fix these specific issues:
- If v4l2_async_match_notify() failed before the sub-notifier handling,
the async connection was unbound and its entry removed from the
sub-device's async connection list. The latter part was also done in
v4l2_async_match_notify().
- The async connection's sd field was only set after creating ancillary
links in v4l2_async_match_notify(). It was however dereferenced in
v4l2_async_unbind_subdev_one(), which was called on error path of
v4l2_async_match_notify() failure.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: "Yew, Chang Ching" <chang.ching.yew@intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Calculating maximum M for scaler configuration involves dividing by
MIN_X_OUTPUT_SIZE limit register's value. Albeit the value is presumably
non-zero, the driver was missing the check it in fact was. Fix this.
Reported-by: Josh Poimboeuf <jpoimboe@kernel.org>
Closes: https://lore.kernel.org/all/ahukd6b3wonye3zgtptvwzvrxldcruazs2exfvll6etjhmcxyj@vq3eh6pd375b/
Fixes: ccfc97bdb5 ("[media] smiapp: Add driver")
Cc: stable@vger.kernel.org # for 5.15 and later
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Tested-by: Nathan Chancellor <nathan@kernel.org> # build
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
v4l2_fwnode_endpoint_parse() and v4l2_fwnode_endpoint_alloc_parse() take
a fwnode as the first argument and leave it up to the caller to check a
valid fwnode has been obtained through various means. Instead, add a check
here so the callers won't need to do that anymore.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Michael Riesch <michael.riesch@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
The vast majority of the callers of v4l2_ctrl_new_fwnode_properties() do
check the returned error code but the function does not set the control
handler's error on failure. This will make error handling more complicated
and prone for bugs.
Always assign the control handler's error field on error in
v4l2_ctrl_new_fwnode_properties().
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
