Introduce sw acceleration for rx path of IP6IP6 tunnels relying on the
netfilter flowtable infrastructure. Subsequent patches will add sw
acceleration for IP6IP6 tunnels tx path.
IP6IP6 rx sw acceleration can be tested running the following scenario
where the traffic is forwarded between two NICs (eth0 and eth1) and an
IP6IP6 tunnel is used to access a remote site (using eth1 as the underlay
device):
ETH0 -- TUN0 <==> ETH1 -- [IP network] -- TUN1 (2001:db8:3::2)
$ip addr show
6: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000
link/ether 00:00:22:33:11:55 brd ff:ff:ff:ff:ff:ff
inet6 2001:db8:1::2/64 scope global nodad
valid_lft forever preferred_lft forever
7: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000
link/ether 00:11:22:33:11:55 brd ff:ff:ff:ff:ff:ff
inet6 2001:db8:2::1/64 scope global nodad
valid_lft forever preferred_lft forever
8: tun0@NONE: <POINTOPOINT,NOARP,UP,LOWER_UP> mtu 1480 qdisc noqueue state UNKNOWN group default qlen 1000
link/tunnel6 2001:db8:2::1 peer 2001:db8:2::2 permaddr ce9c:2940:7dcc::
inet6 2002:db8:1::1/64 scope global nodad
valid_lft forever preferred_lft forever
$ip -6 route show
2001:db8:1::/64 dev eth0 proto kernel metric 256 pref medium
2001:db8:2::/64 dev eth1 proto kernel metric 256 pref medium
2002:db8:1::/64 dev tun0 proto kernel metric 256 pref medium
default via 2002:db8:1::2 dev tun0 metric 1024 pref medium
$nft list ruleset
table inet filter {
flowtable ft {
hook ingress priority filter
devices = { eth0, eth1 }
}
chain forward {
type filter hook forward priority filter; policy accept;
meta l4proto { tcp, udp } flow add @ft
}
}
Reproducing the scenario described above using veths I got the following
results:
- TCP stream received from the IPIP tunnel:
- net-next: (baseline) ~ 81Gbps
- net-next + IP6IP6 flowtbale support: ~112Gbps
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Add tunnel hdr_size and tunnel proto fields in nf_flowtable_ctx struct
in order to store IP tunnel header size and protocol used during IPIP
and IP6IP6 tunnel sw offloading decapsulation and avoid recomputing them
during tunnel header pop since this is constant for IPv6.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Rely on nf_flowtable_ctx struct pointer in nf_flow_ip4_tunnel_proto and
nf_flow_skb_encap_protocol routine signature. This is a preliminary patch
to introduce IP6IP6 flowtable acceleration since nf_flowtable_ctx will
be used to store IP6IP6 tunnel info.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
The s2io driver supports Exar (formerly Neterion and S2io) PCI-X 10
Gigabit Ethernet cards. Hardware supporting PCI-X has not been
manufactured in years. On x86, it was quickly replaced by PCIe. While
it stuck around longer on POWER hardware, the last POWER hardware to
support it was POWER7, which is not supported by ppc64le Linux
distributions. The last supported mainstream ppc64 Linux distribution
was RHEL 7; while it is still supported under ELS, ELS is only
available for x86 and IBM Z. It is possible to use many PCI-X cards in
standard PCI slots (which are still available on new motherboards), but
it does not make sense to do so for 10 Gigabit Ethernet because the
maximum bandwidth of standard PCI is only 1067 Mbps. It is therefore
highly unlikely that this driver is still being used. Remove the
driver, and move the former maintainer to the CREDITS file (restoring
credit for the vxge driver, which was removed in commit f05643a0f6
("eth: remove neterion/vxge").
Signed-off-by: Ethan Nelson-Moore <enelsonmoore@gmail.com>
Link: https://patch.msgid.link/20260126031352.22997-1-enelsonmoore@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
__inet6_csk_dst_check() is a very simple wrapper with no value,
it is used only once.
Directly use __sk_dst_check().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20260127211203.1524339-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is a bug in assoc_sk_only_mismatch() and
assoc_sk_only_mismatch_tx() that creates a race condition which
triggers test flakes in later test cases e.g. data_send_bad_key().
The problem is that the client uses the "conn clr" rpc to setup a data
connection with psp_responder, but never uses a matching "data close"
rpc. This creates a race condition where if the client can queue
another data sock request, like in data_send_bad_key(), before the
server can accept the old connection from the backlog we end up in a
situation where we have two connections in the backlog: one for the
closed connection we have received a FIN for, and one for the new PSP
connection which is expecting to do key exchange.
From there the server pops the closed connection from the backlog, but
the data_send_bad_key() test case in psp.py hangs waiting to perform
key exchange.
The fix is to properly use _conn_close, which fill force the server to
remove the closed connection from the backlog before sending the RPC
ack to the client.
Signed-off-by: Daniel Zahka <daniel.zahka@gmail.com>
Link: https://patch.msgid.link/20260127-psp-flaky-test-v1-1-13403e390af3@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Passing IRQF_ONESHOT ensures that the interrupt source is masked until
the secondary (threaded) handler is done. If only a primary handler is
used then the flag makes no sense because the interrupt can not fire
(again) while its handler is running.
The flag also disallows force-threading of the primary handler and the
irq-core will warn about this as of commit aef30c8d56 ("genirq: Warn
about using IRQF_ONESHOT without a threaded handler").
The IRQF_ONESHOT flag was added in commit 0fabe1021f ("MIPS:
DECstation I/O ASIC DMA interrupt classes"). It moved
clear_ioasic_dma_irq() from the driver into the irq-chip.
For EOI interrupts the clear_ioasic_dma_irq() callback is now invoked as
->irq_eoi() which is invoked after the IRQ was handled while the
interrupt is masked due to IRQF_ONESHOT. Without IRQF_ONESHOT it would
be invoked while interrupt is unmasked (but interrupts are disabled).
If it is *required* to invoke EOI-ack while the interrupt is masked (and
not a misunderstanding) due to irq-chip cascading/ hierarchical reasons
then using handle_fasteoi_mask_irq() as flow-handler would be the right
way to do so.
Remove IRQF_ONESHOT to irqflags.
Cc: Andrew Lunn <andrew+netdev@lunn.ch>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://patch.msgid.link/20260127135334.qUEaYP9G@linutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eric Dumazet says:
====================
tcp: tcp_tx_timestamp() fix
Fix an old bug in tcp_tx_timestamp().
Add one corresponding packetdrill test.
====================
Link: https://patch.msgid.link/20260127123828.4098577-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Test tcp_tx_timestamp() behavior after ("tcp: tcp_tx_timestamp()
must look at the rtx queue").
Without the fix, this new test fails like this:
tcp_timestamping_tcp_tx_timestamp_bug.pkt:55: runtime error in recvmsg call: Expected result 0 but got -1 with errno 11 (Resource temporarily unavailable)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Jason Xing <kerneljasonxing@gmail.com>
Link: https://patch.msgid.link/20260127123828.4098577-3-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
tcp_tx_timestamp() is only called at the end of tcp_sendmsg_locked()
before the final tcp_push().
By the time it is called, it is possible all the copied data
has been sent already (transmit queue is empty).
If this is the case, use the last skb in the rtx queue.
Fixes: 75c119afe1 ("tcp: implement rb-tree based retransmit queue")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Jason Xing <kerneljasonxing@gmail.com>
Link: https://patch.msgid.link/20260127123828.4098577-2-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ip_fib_metrics_init() is only called from fib_create_info()
and ip6_route_info_create().
Let's use EXPORT_IPV6_MOD_GPL() instead.
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260127081335.646666-1-kuniyu@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eric Dumazet says:
====================
tcp: make tcp_ack() faster
Move tcp_rack_update_reo_wnd() and tcp_rack_advance() to tcp_input.c
to allow their (auto)inlining.
No functional change in this series.
====================
Link: https://patch.msgid.link/20260127032147.3498272-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
tcp_rack_advance() is called from tcp_ack() and tcp_sacktag_one().
Moving it to tcp_input.c allows the compiler to inline it and save
both space and cpu cycles in TCP fast path.
$ scripts/bloat-o-meter -t vmlinux.1 vmlinux.2
add/remove: 0/2 grow/shrink: 1/1 up/down: 98/-132 (-34)
Function old new delta
tcp_ack 5741 5839 +98
tcp_sacktag_one 407 395 -12
__pfx_tcp_rack_advance 16 - -16
tcp_rack_advance 104 - -104
Total: Before=22572680, After=22572646, chg -0.00%
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20260127032147.3498272-4-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
tcp_rack_update_reo_wnd() is called only once from tcp_ack()
Move it to tcp_input.c so that it can be inlined by the compiler
to save space and cpu cycles.
$ scripts/bloat-o-meter -t vmlinux.old vmlinux.new
add/remove: 0/2 grow/shrink: 1/0 up/down: 110/-153 (-43)
Function old new delta
tcp_ack 5631 5741 +110
__pfx_tcp_rack_update_reo_wnd 16 - -16
tcp_rack_update_reo_wnd 137 - -137
Total: Before=22572723, After=22572680, chg -0.00%
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20260127032147.3498272-3-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It is unlikely we have to call tcp_process_tlp_ack().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20260127032147.3498272-2-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some PTP hardware clock (PHC) devices may return -EOPNOTSUPP for
operations like settime, adjtime, or adjfreq. This commonly occurs
with timestamp-only PHC implementations that don't support full clock
control.
For background, syzbot previously exposed a crash risk when PTP clock
drivers lacked required callbacks[1]. Subsequent work[2] made callback
presence a registration requirement. As a result, some drivers (like
iwlwifi MVM/MLD[3]) now provide stub callbacks that return -EOPNOTSUPP
for unsupported operations.
When phc_ctl encounters such devices, the "Operation not supported"
error should be treated as a skip (device limitation) rather than a
test failure. This patch:
- Adds [SKIP] output handling in log_test()
- Detects "Operation not supported" from phc_ctl and returns ksft_skip
- Returns ksft_skip if all tests are skipped, preventing false-positive
results when testing timestamp-only PHC implementations
Link: https://lore.kernel.org/netdev/20251028043216.1971292-1-junjie.cao@intel.com/ [1]
Link: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=dfb073d32cac [2]
Link: https://lore.kernel.org/netdev/20251204123204.9316-1-ziyao@disroot.org/ [3]
Signed-off-by: Junjie Cao <junjie.cao@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260126061532.12532-2-junjie.cao@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The kselftest framework defines KSFT_SKIP=4 as the standard exit code
for skipped tests. However, phc.sh currently uses a mix of 'exit 0' and
'exit 1' to indicate skip conditions, which can confuse test harnesses
and CI systems.
This patch introduces ksft_skip=4 variable and unifies all skip exit
paths to use 'exit $ksft_skip', consistent with other selftests like
net/lib.sh and net/fib_nexthops.sh.
Signed-off-by: Junjie Cao <junjie.cao@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260126061532.12532-1-junjie.cao@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The int51x1 driver uses the same requests as USB CDC to handle packet
filtering, but provides its own definitions and function to handle it.
The chip datasheet says the requests are CDC compliant. Replace this
unnecessary code with a reference to usbnet_cdc_update_filter.
Also fix the broken datasheet link and remove an empty comment.
Signed-off-by: Ethan Nelson-Moore <enelsonmoore@gmail.com>
Link: https://patch.msgid.link/20260126044049.40359-1-enelsonmoore@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2026-01-26 (ice, idpf)
For ice:
Jake converts ring stats to utilize u64_stats APIs and performs some
cleanups along the way.
Alexander reorganizes layout of Tx and Rx rings for cacheline
locality and utilizes __cacheline_group* macros on the new layouts.
For idpf:
YiFei Zhu adds support for BPF kfunc reporting of hardware Rx timestamps.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
idpf: export RX hardware timestamping information to XDP
ice: reshuffle and group Rx and Tx queue fields by cachelines
ice: convert all ring stats to u64_stats_t
ice: shorten ring stat names and add accessors
ice: use u64_stats API to access pkts/bytes in dim sample
ice: remove ice_q_stats struct and use struct_group
ice: pass pointer to ice_fetch_u64_stats_per_ring
====================
Link: https://patch.msgid.link/20260126224313.3847849-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All drivers that need to report the RX ring count now implement the
get_rx_ring_count callback directly. Remove the legacy fallback path
that obtained this information by calling get_rxnfc with ETHTOOL_GRXRINGS.
This simplifies the code and makes get_rx_ring_count the only way
to retrieve the RX ring count.
Note: ethtool_get_rx_ring_count() returns int to allow returning
-EOPNOTSUPP, while the callback returns u32. The implicit conversion
is safe since RX ring counts will not exceed INT_MAX while we are still
alive.
Signed-off-by: Breno Leitao <leitao@debian.org>
Link: https://patch.msgid.link/20260126-grxring_final-v1-1-0981cb24512e@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Gal Pressman says:
====================
Single MSS length in UDP GSO_PARTIAL
This series addresses an inconsistency in how UDP GSO_PARTIAL handles
the UDP header length field.
Currently, when GSO_PARTIAL segmentation is used, the UDP header length
contains the large MSS size, requiring drivers to manually adjust it
before transmitting. This is inconsistent with how tunnel GSO_PARTIAL
handles outer headers in UDP tunnels, where the length is set to the
single segment size.
This was originally suggested by Alexander Duyck back in 2018:
https://lore.kernel.org/netdev/CAKgT0UcdnUWgr3KQ=RnLKigokkiUuYefmL-ePpDvJOBNpKScFA@mail.gmail.com/
The first patch fixes the core UDP offload code to set the UDP length
field to the single segment size (gso_size + UDP header) instead of the
large MSS size. This provides hardware with a proper template length
value for final segmentation.
The subsequent patches remove the now redundant UDP header length
adjustments from the mlx5e and aquantia drivers, as the core code now
handles this correctly.
I couldn't find any other drivers that support UDP GSO_PARTIAL; idpf
supports UDP segmentation, but it does not use GSO_PARTIAL.
====================
Link: https://patch.msgid.link/20260125121649.778086-1-gal@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
GSO_PARTIAL now takes care of updating the UDP header length, remove the
redundant assignment in aq_nic_map_skb().
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Link: https://patch.msgid.link/20260125121649.778086-4-gal@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
GSO_PARTIAL now takes care of updating the UDP header length,
mlx5e_udp_gso_handle_tx_skb() is redundant, remove it.
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20260125121649.778086-3-gal@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In GSO_PARTIAL segmentation, set the UDP length field to the single
segment size (gso_size + UDP header) instead of the large MSS size.
This provides hardware with a template length value for final
segmentation, similar to how tunnel GSO_PARTIAL handles outer headers
in UDP tunnels.
This will remove the need to manually adjust the UDP header length in
the drivers, as can be seen in subsequent patches.
This was suggested by Alex in 2018:
https://lore.kernel.org/netdev/CAKgT0UcdnUWgr3KQ=RnLKigokkiUuYefmL-ePpDvJOBNpKScFA@mail.gmail.com/
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20260125121649.778086-2-gal@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As the stmmac_priv struct is passed to the fix_soc_reset() method which
has the ioaddr, there is no need to pass ioaddr separately. Pass just
the stmmac_priv struct. Fix up the glues that use it.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/E1vkLmM-00000005vE1-0nop@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The first byte of the Rx frame is a copy of the Rx status register, so
0x40 corresponds to RSR_MF (meaning the frame is multicast). Replace
0x40 with RSR_MF for clarity. (All other bits of the RSR indicate
errors. The fact that the driver ignores these errors will be fixed by
a later patch.)
The first byte of the status URB is a copy of the NSR, so 0x40
corresponds to NSR_LINKST. Replace 0x40 with NSR_LINKST for clarity.
Signed-off-by: Ethan Nelson-Moore <enelsonmoore@gmail.com>
Reviewed-by: Peter Korsgaard <peter@korsgaard.com>
Link: https://patch.msgid.link/20260124032248.26807-1-enelsonmoore@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that there are no users of the low-level SHA-1 interface, remove it.
Specifically:
- Remove SHA1_DIGEST_WORDS (no longer used)
- Remove sha1_init_raw() (no longer used)
- Rename sha1_transform() to sha1_block_generic() and make it static
- Move SHA1_WORKSPACE_WORDS into lib/crypto/sha1.c
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Link: https://patch.msgid.link/20260123051656.396371-3-ebiggers@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There's now a proper SHA-1 API that follows the usual conventions for
hash function APIs: sha1_init(), sha1_update(), sha1_final(), sha1().
The only remaining user of the older low-level SHA-1 API,
sha1_init_raw() and sha1_transform(), is ipv6_generate_stable_address().
I'd like to remove this older API, which is too low-level.
Unfortunately, ipv6_generate_stable_address() does in fact skip the
SHA-1 finalization for some reason. So the values it computes are not
standard SHA-1 values, and it sort of does want the low-level API.
Still, it's still possible to use the higher-level functions sha1_init()
and sha1_update() to get the same result, provided that the resulting
state is used directly, skipping sha1_final().
So, let's do that instead. This will allow removing the low-level API.
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Acked-by: David Ahern <dsahern@kernel.org>
Link: https://patch.msgid.link/20260123051656.396371-2-ebiggers@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Group the MACPHY register offsets and associated bitfields together
to become self-documenting which definitions are associated with
which register.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1vkL1y-00000005usW-1TKX@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
rk3328 contains two GMAC instances - gmac2io and gmac2phy. While the
gmac2io instance may be connected to an external PHY, the gmac2phy
instance is permanently connected via RMII to an on-SoC integrated PHY.
The driver currently tests for the gmac2phy instance by checking
bsp_priv->integrated_phy (determined from the PHY's phy-is-integrated
property) and sometimes that the interface mode is RMII. This works
because the rk3328.dtsi has:
gmac2phy: ethernet@ff550000 {
compatible = "rockchip,rk3328-gmac";
phy-mode = "rmii";
phy-handle = <&phy>;
mdio {
phy: ethernet-phy@0 {
phy-is-integrated;
};
};
};
The driver contains a mechanism to look up the MMIO address in a table
to determine bsp_priv->id, which is used for every other Rockchip
device. Switch rk3328 to use this mechanism to determine bsp_priv->id
and use that to select which GRF register is used for configuration,
similarly to how the other Rockchip SoCs handle such differences.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1vkL1t-00000005usQ-0vjt@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It is not worth having a common rk_phy_power_ctl() when the only
difference is which regulator function is called. Also, passing
true/false is non-descriptive. Split this function, moving the code
appropriately into rk_phy_powerup() and rk_phy_powerdown().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1vkL1o-00000005usJ-08hy@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In https://lore.kernel.org/netdev/aDne1Ybuvbk0AwG0@shell.armlinux.org.uk/
I requested that a follow-up patch to change the name of dwmac-rk's
phy_power_on() function, which clashes with the drivers/phy function
of the same name. This can cause confusion when grepping for this
function name, or when reviewing code. Thankfully, stmmac doesn't make
use of drivers/phy which saves this from compile errors.
However, as is the usual case when a request is made as part of a
review, if the review leads to successful application of the patch the
author doesn't bother following up with any such requests, and so the
problem falls back onto the reviewer to address... so here is the
solution.
Rename dwmac-rk's function to rk_phy_power_ctl(), as the function both
powers up and down.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1vkL1i-00000005usD-3lhz@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
TCP fast path can (auto)inline this helper, instead
of (auto)inling it from tcp_send_fin().
No change of overall code size, but tcp_sendmsg() is faster.
$ scripts/bloat-o-meter -t vmlinux.old vmlinux.new
add/remove: 0/0 grow/shrink: 1/1 up/down: 141/-140 (1)
Function old new delta
tcp_stream_alloc_skb 216 357 +141
tcp_send_fin 688 548 -140
Total: Before=22236729, After=22236730, chg +0.00%
BTW, we might change tcp_send_fin() to use tcp_stream_alloc_skb().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Link: https://patch.msgid.link/20260123111605.4089200-1-edumazet@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Jijie Shao says:
====================
extend bit width in the flow director of HNS3 driver
The bit widths of HCLGE_FD_AD_QID and HCLGE_FD_AD_COUNTER_NUM are
increased to support higher specifications.
Note: The hardware already supports the specifications.
====================
Link: https://patch.msgid.link/20260123094756.3718516-1-shaojijie@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Currently, HCLGE_FD_AD_COUNTER_NUM has only 7 bits and supports a
maximum of 127 counter_id. However, there are actually scenarios
where the counter_id exceeds 127.
This patch adds an additional bit to HCLGE_FD_AD_QID to ensure
that counter_id greater than 127 are supported.
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Link: https://patch.msgid.link/20260123094756.3718516-3-shaojijie@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Currently, HCLGE_FD_AD_QID has only 10 bits and supports a
maximum of 1023 queues. However, there are actually scenarios
where the queue_id exceeds 1023.
This patch adds an additional bit to HCLGE_FD_AD_QID to ensure
that queue_id greater than 1023 are supported.
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Link: https://patch.msgid.link/20260123094756.3718516-2-shaojijie@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Daniel Golle says:
====================
net: dsa: lantiq: add support for Intel GSW150
The Intel GSW150 Ethernet Switch (aka. Lantiq PEB7084) is the predecessor of
MaxLinear's GSW1xx series of switches. It shares most features, but has a
slightly different port layout and different MII interfaces.
Adding support for this switch to the mxl-gsw1xx driver is quite trivial.
====================
Link: https://patch.msgid.link/cover.1769099517.git.daniel@makrotopia.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add support for the Intel GSW150 (aka. Lantiq PEB7084) switch IC to
the mxl-gsw1xx driver. This switch comes with 5 Gigabit Ethernet
copper ports (Intel XWAY PHY11G (xRX v1.2 integrated) PHYs) as well as
one GMII/RGMII and one RGMII port.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://patch.msgid.link/c84cf94337bf1be30940841b338b6368468c6e17.1769099517.git.daniel@makrotopia.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The Lantiq GSWIP and MaxLinear GSW1xx drivers are currently relying on a
hard-coded mapping of MII ports to their respective MII_CFG and MII_PCDU
registers and only allow applying an offset to the port index.
While this is sufficient for the currently supported hardware, the very
similar Intel GSW150 (aka. Lantiq PEB7084) cannot be described using
this arrangement.
Introduce two arrays to specify the MII_CFG and MII_PCDU registers for
each port, replacing the current bitmap used to safeguard MII ports as
well as the port index offset.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://patch.msgid.link/63fc01195196384f5e244a0ce9ec2ae3a6c08fe3.1769099517.git.daniel@makrotopia.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add tests that validate vsock sockets are resilient to deleting
namespaces. The vsock sockets should still function normally.
The function check_ns_delete_doesnt_break_connection() is added to
re-use the step-by-step logic of 1) setup connections, 2) delete ns,
3) check that the connections are still ok.
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Bobby Eshleman <bobbyeshleman@meta.com>
Link: https://patch.msgid.link/20260121-vsock-vmtest-v16-12-2859a7512097@meta.com
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add tests to validate namespace correctness using vsock_test and socat.
The vsock_test tool is used to validate expected success tests, but
socat is used for expected failure tests. socat is used to ensure that
connections are rejected outright instead of failing due to some other
socket behavior (as tested in vsock_test). Additionally, socat is
already required for tunneling TCP traffic from vsock_test. Using only
one of the vsock_test tests like 'test_stream_client_close_client' would
have yielded a similar result, but doing so wouldn't remove the socat
dependency.
Additionally, check for the dependency socat. socat needs special
handling beyond just checking if it is on the path because it must be
compiled with support for both vsock and unix. The function
check_socat() checks that this support exists.
Add more padding to test name printf strings because the tests added in
this patch would otherwise overflow.
Add vm_dmesg_* helpers to encapsulate checking dmesg
for oops and warnings.
Add ability to pass extra args to host-side vsock_test so that tests
that cause false positives may be skipped with arg --skip.
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Bobby Eshleman <bobbyeshleman@meta.com>
Link: https://patch.msgid.link/20260121-vsock-vmtest-v16-11-2859a7512097@meta.com
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
