There's no reason for pcie code to call itself indirectly,
directly use the pcie functions instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Yedidya Ben Shimol <yedidya.ben.shimol@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250502155404.52db0b9fba15.I062e766ded86f61ec86104c28b84767f1c29ea78@changeid
Since there are two bytes hole in struct iwl_dev_info, add
a subdev_mask to match with. Also, since the PCI IDs list
needs to match first, and the dev-info list is matched from
the bottom up, remove unnecessary entries.
With this, even though there are new entries from previous
changes, the overall size is slightly reduced.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250502155404.689f9b335cbe.I66f1344b6ac7aa3665696637c97fa843c2307423@changeid
A long time ago, when transport vs. device configs were
introduced, we wanted to eventually have a list of PCI
IDs and a separate list of devices, but for simplicity
embedded the transport config in the whole config, and
it all got confusing.
Finish splitting that out. Doing so requires having more
IWL_DEV_INFO() entries, but the whole trans/cfg aliasing
goes away and the code becomes a lot simpler.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250502155404.e03f65c0f693.I076a997f800db455b575008f9488b151738ad7ec@changeid
Remove the erroneously named IWL_DEVICE_BZ_COMMON macro
from the Sc file and fix some indentation. Also bump the
minimum FW version since it's not released yet anyway,
right now this is mostly to make the config different
from iwl_bz_cfg which would otherwise be the same with
the upcoming transport config cleanups.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250502155404.b313d54b8809.Ia975b6d5460996f2a2761dd3d0fef4a56f1f3e24@changeid
It's not clear that it makes sense to have any matches
for IWL_CFG_ANY for this bit, but let's assume for now
that this makes sense. Then, it's clearer to call this
BW_NOT_LIMITED rather than BW_NO_LIMIT, since the last
change.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250502155404.9b39693b505c.Ib47aa6a072a0e61bbba28383ce54764cd859f19c@changeid
The BW limit, cores and RF ID are matched in the subdevice ID,
so it doesn't really make sense to have both SUBDEV() match and
a match on any of those three. In particular, for Killer devices
the subdevice ID doesn't even follow the layout, so no matching
should be on those three values at all, only with SUBDEV().
Change the logic around the BW limit to have it more like all
the other things: only a bw_limit match in the dev_info, and
put the actual bandwidth into struct iwl_cfg. This duplicates a
number of those values, but that way the logic is clearer.
Add a test that checks that the three matches mentioned above
are not used in conjunction with SUBDEV(), and check that if
the bw_limit is matched, a BW limit is provided in the config.
Also check that the "Killer" devices have a SUBDEV() match.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250502155404.a185eac2736c.I87ee87300c92518a1d3296d3eda9fd4163e9085e@changeid
This really is the same device as covered by iwl_cfg_bz,
just the discrete version. Since discrete vs integrated
is handled in the transport config, there's no need to
have both. Remove iwl_cfg_gl.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250502151751.fbb78183dc85.Ic5429009677ae1023cf1f43a655e90409a30c493@changeid
This was used in some really old devices, and then got
carried forward to Qu devices, even though on those we
don't need it at all since the TX aggregation start is
offloaded to the firmware. Remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250502151751.9c2689e2ca8e.I8274b29ca64d9ef9d1e357bbe34ca3a4b97aeb7a@changeid
Now that the fw_name_mac is no longer around and derived
from the MAC type automatically, we no longer need to have
different configurations for Qu/QuZ. Combine them. For the
killer AX1650s/i, also fix the names, there was a mixup.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250502151751.957fbb5437ce.If51ad0b2c8afaaa131208125af3bc292793613bb@changeid
This was used in the past for NoA and/or beacon filter
testing, but these days everything is tested via debugfs
or special FW commands, so remove the testmode.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250430155443.751018e0ed8e.I21557a9a3d57234187f1b0b2182a1714ecc66b9a@changeid
When a soft AP is started, it may not use the full configured
bandwidth (e.g. if no station is connected). As a result, the
responder will not support the configured bandwidth. Since the
responder supports ranging with unassociated stations, there is
no indication to the driver when the full bandwidth should be enabled.
Fix it by configuring the AP to always use the full bandwidth when a
responder is supported.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250430155443.620fe8099fff.Id50675f4d4c524b0a7ee602c48af538a327010e0@changeid
When a channel context is added, it is still not assigned to the link
and the link is not yet active. As a result, the channel context
min_def is used when the AP is started, even when the full bandwidth
should be used.
Fix it by updating the PHY channel context when the link is already
active so the full bandwidth is used when needed.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250430155443.30b043b10fb1.I62c2aa58687e4796b759fa68132122119a337b49@changeid
This version fixes the issue that was worked around by
iwl_mvm_smps_workaround. So for FWs with the new version don't do the
workaround, and set new bit added in this version when appropriate.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://patch.msgid.link/20250430155443.5c9a0181a84b.I9a03bc07a7b3f6e37cc1c0c1af5719e765a05897@changeid
Implement TOP reset (new in the SC family), which resets much
of the (shared) hardware without resetting the bus interfaces.
Use it to recover from TOP fatal error, or if manually used;
we'll need to add using it for FSEQ updates later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250430155443.12f38024a3b4.I9c22f6c4f6de64f3b34ccd898370ec1859ab7dbf@changeid
This version fixes the issue that was worked around by
iwl_mld_smps_wa. So for FWs with the new version don't do the
workaround, and set new bit added in this version when appropriate.
While at it, rename iwl_mld_smps_wa to iwl_mld_smps_workaround.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://patch.msgid.link/20250430155443.77fdb18d1ee0.I93688612ac4f6ec99da9bc54bee16554ef40a40b@changeid
PPAG command version 7 will send exact data read from BIOS to
firmware without filtering/altering BIOS data. This enables the
driver to become purely a pipe for this feature.
Signed-off-by: Pagadala Yesu Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250430151952.88ed7b2cadef.Iad78f6cec617d1f111b704352795dde81af71a99@changeid
ppag_ver variable is holding PPAG BIOS revision but name misleading
as PPAG command API version, So rename to ppag_bios_rev.
This will improve code readability but doesn't alter behaviour.
Signed-off-by: Pagadala Yesu Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250430151952.be51850947df.If81d88cd2d38299faf1e2a3db5efbc021650f907@changeid
If iwl_mld_change_vif_links failed to add the requested link(s)
because the FW is dead (error before recovery), there is no point
in returning an error value, as the reconfig will re-add the link(s)
after the FW is started.
Return 0 in that case, and WARN in the others.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250430151952.c549c72b1f37.I445bf723e9befc9541b4abd0ec7c72db8f1ff177@changeid
When BT is ON, EMLSR with one of the links operating on 2.4 GHz
is allowed only if it meets following conditions.
In this patch:
1. during link selection, when BT is ON, allow emlsr only if BT
pentalty is < 7%.
2. exit EMLSR if BT is turned ON and one of the links is operating
on 2.4 GHz with BT penalty > 7%
Signed-off-by: Somashekhar Puttagangaiah <somashekhar.puttagangaiah@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250430151952.d30212ec3901.I48e3d5bd6b0b8583f98057c38d2ee30fff5abd8a@changeid
