adm1266_set_rtc() seeds the chip's SET_RTC register from
ktime_get_seconds(), which returns CLOCK_MONOTONIC -- i.e. seconds
since the host last booted, not seconds since the Unix epoch.
The chip stamps that value into every blackbox record it captures.
Userspace reading those timestamps back expects wall-clock seconds:
that's what the SET_RTC frame layout documents (datasheet Rev. D,
Table 84) and what every other consumer of "seconds since epoch"
assumes. Seeding from CLOCK_MONOTONIC gives blackbox records a
timestamp that is only meaningful within a single boot of the host
and silently resets to small values on every reboot.
Switch to ktime_get_real_seconds() so the seed matches what the
register is documented to hold.
Fixes: 15609d1893 ("hwmon: (pmbus/adm1266) read blackbox")
Cc: stable@vger.kernel.org
Signed-off-by: Abdurrahman Hussain <abdurrahman@nexthop.ai>
Link: https://lore.kernel.org/r/20260515-adm1266-fixes-v1-1-1c1ea1349cfe@nexthop.ai
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The EC signature check uses && instead of || between the four
byte comparisons. With &&, the condition is true only when ALL
four bytes fail to match simultaneously, meaning the driver
accepts a device as a valid Microchip EC if ANY single byte of
the 4-byte "MCHP" signature happens to match.
Due to short-circuit evaluation, if the first byte reads back as
'M' (0x4D, a very common register value), the remaining three
comparisons are skipped entirely and the device is accepted.
Change && to || so the check rejects devices that do not fully
match the expected EC signature, as originally intended.
Fixes: 70118f85e6 ("hwmon: Add EC Chip driver for Lenovo ThinkStation motherboards")
Reviewed-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Signed-off-by: Kean Ren <rh_king@163.com>
Link: https://lore.kernel.org/r/20260521035228.533317-3-rh_king@163.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Replace manual request_region()/release_region() with
devm_request_region(). This lets the device-managed framework
handle I/O region lifetime automatically and fixes:
- A double release_region() when probe fails after acquiring the
I/O region: the probe error path releases it, and then
lenovo_ec_init() releases it again on the same error path.
- A release-after-use window in lenovo_ec_exit() where
release_region() was called before platform_device_unregister(),
leaving the hwmon device active with a released I/O region.
- Missing release_region() in lenovo_ec_probe() if
devm_hwmon_device_register_with_info() fails.
Remove all four manual release_region() calls that are now handled
automatically and replace request_region with
devm_request_region, use dev_err replace pr_err.
Also remove the now-unnecessary braces around the single-statement
if body.
Fixes: 70118f85e6 ("hwmon: Add EC Chip driver for Lenovo ThinkStation motherboards")
Reviewed-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Signed-off-by: Kean Ren <rh_king@163.com>
Link: https://lore.kernel.org/r/20260521035228.533317-2-rh_king@163.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Commit 1feda5eb77 ("drm/exynos: Use selected dma_dev default iommu
domain instead of a fake one") removed the code around creating a
custom IOMMU domain, but forgot to remove the stub.
Remove the iommu_dma_init_domain() stub as the function is no longer
referenced, and was also made private to the IOMMU DMA code.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Use flush_work() instead of cancel_work_sync() to terminate pending IRQ
work in cs35l56_sdw_remove(). And flush_work() again after masking the
interrupts to flush any queueing that was racing with the masking. This is
the same sequence as cs35l56_sdw_system_suspend().
cs35l56_sdw_interrupt() takes the pm_runtime to prevent the bus powering-
down before the interrupt status can be read and handled. The work releases
this pm_runtime. So cancelling it, instead of flushing, could leave an
unbalanced pm_runtime.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: e496112529 ("ASoC: cs35l56: Add driver for Cirrus Logic CS35L56")
Link: https://patch.msgid.link/20260521123057.988732-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
After commit feee6b2989 ("mm/memory_hotplug: shrink zones when
offlining memory"), __remove_pages() doesn't need the "zone" parameter
so the "page" variable is also unused. Remove the unused code to avoid
such build warning:
arch/loongarch/mm/init.c: In function 'arch_remove_memory':
arch/loongarch/mm/init.c:134:22: warning: variable 'page' set but not used [-Wunused-but-set-variable=]
134 | struct page *page = pfn_to_page(start_pfn);
Cc: <stable@vger.kernel.org>
Reviewed-by: Guo Ren <guoren@kernel.org>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Validate the relocation address against the initrd region specified via
"initrd=" or "initrdmem=" on the command line. Reject relocation targets
that overlap the initrd to prevent memory corruption during early boot.
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: WANG Rui <wangrui@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
When the kernel is relocated during early boot (efistub or kexec_file),
a randomized load address may has already been selected and applied. In
this case, performing KASLR again in relocate.c is unnecessary.
Note: strictly-defined KASLR means the kernel's final runtime address
has a random offset from the kernel's load address, which is implemented
in relocate.c; broadly-defined KALSR means the kernel's final runtime
address has a random offset from the kernel's link address (a.k.a.
VMLINUX_LOAD_ADDRESS), which also include the efistlub implementation,
kexec_file implementation and QEMU direct kernel boot. kaslr_disabled()
return true only means strictly-defined KASLR is disabled.
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: WANG Rui <wangrui@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Introduce efi_get_kimg_kaslr_address() helper to compute the preferred
kernel image load address dynamically when CONFIG_RANDOMIZE_BASE is
enabled. The function derives a random offset by using the EFI-provided
randomness combined with the timer tick value, and constrains it within
CONFIG_RANDOMIZE_BASE_MAX_OFFSET.
Update EFI_KIMG_PREFERRED_ADDRESS to call this helper so that the EFI
stub can select a randomized load address when KASLR is active, while
preserving the original base address behavior when KASLR is disabled or
"nokaslr" is specified.
Note: LoongArch can't KASLR for hibernation, so set efi_nokaslr to true
if "resume=<devname>" is explicitly specified in cmdline.
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: WANG Rui <wangrui@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
As the output file is currently never created, the check will run every
time, even if the inputs have not changed.
Create an empty output file which allows make to skip the execution when
it is not necessary.
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Vincent Donnefort <vdonnefort@google.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Link: https://patch.msgid.link/20260520-tracing-ringbuffer-check-v1-1-d979cfab1338@weissschuh.net
Fixes: 1211907ac0 ("tracing: Generate undef symbols allowlist for simple_ring_buffer")
Fixes: 58b4bd1839 ("tracing: Adjust cmd_check_undefined to show unexpected undefined symbols")
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The unload_page callback expects the return value of load_page() as its
argument: ret = load_page(va); unload(ret). Fix the rollback code in
simple_ring_buffer_init_mm() where the descriptor's VA is used instead
of the loaded page address.
Link: https://patch.msgid.link/20260512141614.1759430-1-vdonnefort@google.com
Fixes: 635923081c ("tracing: load/unload page callbacks for simple_ring_buffer")
Signed-off-by: Vincent Donnefort <vdonnefort@google.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
nr_subbufs in the ring buffer metadata is always initialized to zero
because it is assigned from cpu_buffer->nr_pages before the page
initialization loop has run. While nr_subbufs is not currently read
by the kernel, it should reflect the actual buffer geometry in the
meta page for correctness.
Move the assignment after the page loop so that cpu_buffer->nr_pages
holds the final count.
Link: https://patch.msgid.link/20260512135420.99194-1-devnexen@gmail.com
Fixes: 34e5b958bd ("tracing: Introduce simple_ring_buffer")
Reviewed-by: Vincent Donnefort <vdonnefort@google.com>
Assisted-by: Claude:claude-opus-4-7
Signed-off-by: David Carlier <devnexen@gmail.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
On real hardware, panic and machine reboot may not flush hardware cache
to memory. This means the persistent ring buffer, which relies on a
coherent state of memory, may not have its events written to the buffer
and they may be lost. Moreover, there may be inconsistency with the
counters which are used for validation of the integrity of the
persistent ring buffer which may cause all data to be discarded.
To avoid this issue, stop recording of the ring buffer on panic and
flush the cache of the ring buffer's memory.
Fixes: e645535a95 ("tracing: Add option to use memmapped memory for trace boot instance")
Cc: stable@vger.kernel.org
Cc: Will Deacon <will@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Ian Rogers <irogers@google.com>
Link: https://patch.msgid.link/177751969602.2136606.12031934362587643488.stgit@mhiramat.tok.corp.google.com
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
When tracing is active while reading the trace file, if the iterator
reading the buffer detects that the writer has passed the iterator head,
it will reset and set a "missed events" flag. This flag is passed to the
output processing to show the user that events were missed:
CPU:4 [LOST EVENTS]
The problem is that the flag is reset after it is checked in
ring_buffer_iter_dropped(). But the "trace" file iterates over all the CPU
ring buffers and it will check if they are dropped when figuring out which
buffer to print next. This prematurely clears the missed_events flag if
the CPU buffer with the missed events is not the one that is printed next.
On the iteration where the CPU buffer with the missed events is printed,
the check if it had missed events would return false and the output does
not show that events were missed.
Do not reset the missed_events flag when checking if there were missed
events, but instead clear it when moving the iterator head to the next
event.
Cc: stable@vger.kernel.org
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Link: https://patch.msgid.link/20260520220801.4fd09d13@fedora
Fixes: c9b7a4a72f ("ring-buffer/tracing: Have iterator acknowledge dropped events")
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
When a buffer is freed either by LRU eviction or because it is unset,
the lockref is marked as dead instantly, which prevents the buffer from
being used after finding it in the buffer hash in xfs_buf_lookup and
xfs_buf_find_insert. But the latter will then not add the new buffer to
the hash because it already found an existing buffer.
Fix this using in two places: Remove the buffer from the hash before
marking the lockref dead so that that no buffer with a dead lockref can
be found in the hash, but if we find one in xfs_buf_find_insert due to
store reordering, handle this case correctly instead of returning an
unhashed buffer.
Fixes: 67fe430397 ("xfs: don't keep a reference for buffers on the LRU")
Reported-by: Andrey Albershteyn <aalbersh@redhat.com>
Reported-by: Carlos Maiolino <cem@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andrey Albershteyn <aalbersh@kernel.org>
Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com>
Signed-off-by: Carlos Maiolino <cem@kernel.org>
After commit 059b7dbd20 ("vsock/virtio: fix potential unbounded skb
queue"), virtio_transport_inc_rx_pkt() subtracts per-skb overhead from
buf_alloc when checking whether a new packet fits. This reduces the
effective receive buffer below what the user configured via
SO_VM_SOCKETS_BUFFER_SIZE, causing legitimate data packets to be
silently dropped and applications that rely on the full buffer size
to deadlock.
Also, the reduced space is not communicated to the remote peer, so
its credit calculation accounts more credit than the receiver will
actually accept, causing data loss (there is no retransmission).
With this approach we currently have failures in
tools/testing/vsock/vsock_test.c. Test 18 sometimes fails, while
test 22 always fails in this way:
18 - SOCK_STREAM MSG_ZEROCOPY...hash mismatch
22 - SOCK_STREAM virtio credit update + SO_RCVLOWAT...send failed:
Resource temporarily unavailable
Fix by allowing at most `buf_alloc * 2` as the total budget for payload
plus skb overhead in virtio_transport_inc_rx_pkt(), similar to how
SO_RCVBUF is doubled to reserve space for sk_buff metadata.
This preserves the full buf_alloc for payload under normal operation,
while still bounding the skb queue growth.
With this patch, all tests in tools/testing/vsock/vsock_test.c are
now passing again.
Fixes: 059b7dbd20 ("vsock/virtio: fix potential unbounded skb queue")
Cc: stable@vger.kernel.org
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://patch.msgid.link/20260518090656.134588-3-sgarzare@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When there is no more space to queue an incoming packet, the packet is
silently dropped. This causes data loss without any notification to
either peer, since there is no retransmission.
Under normal circumstances, this should never happen. However, it could
happen if the other peer doesn't respect the credit, or if the skb
overhead, which we recently began to take into account with commit
059b7dbd20 ("vsock/virtio: fix potential unbounded skb queue"),
is too high.
Fix this by resetting the connection and setting the local socket error
to ENOBUFS when virtio_transport_recv_enqueue() can no longer queue a
packet, so both peers are explicitly notified of the failure rather than
silently losing data.
Fixes: ae6fcfbf5f ("vsock/virtio: discard packets if credit is not respected")
Cc: stable@vger.kernel.org
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://patch.msgid.link/20260518090656.134588-2-sgarzare@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Ranjani no longer works on Intel/SOF audio drivers and her email address
now bounce due to her departure from Intel.
Unfortunately, she was not able to send the removal mail by herself.
Thanks for the years of work and dedication, Ranjani!
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Jyri Sarha <jyri.sarha@linux.intel.com>
Link: https://patch.msgid.link/20260520140001.1375-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert the IT66121 HDMI bridge driver from manually registering an
hdmi-codec platform device to using the DRM HDMI Audio Helper framework
via DRM_BRIDGE_OP_HDMI_AUDIO instead.
The previous implementation manually allocated hdmi_codec_pdata,
registered the platform device, and implemented hdmi_codec_ops callbacks
including get_eld. The new approach sets DRM_BRIDGE_OP_HDMI_AUDIO on the
bridge, letting the framework handle the codec registration. This also
resolves some non-compliance issues with the current audio implementation,
such as HDMI audio advertising a non-functional capture stream to userspace.
The audio callbacks are converted from hdmi_codec_ops signatures to
drm_bridge_funcs hdmi_audio callbacks:
- it66121_audio_hw_params -> it66121_hdmi_audio_prepare
- it66121_audio_startup -> it66121_hdmi_audio_startup
- it66121_audio_shutdown -> it66121_hdmi_audio_shutdown
- it66121_audio_mute -> it66121_hdmi_audio_mute_stream
The it66121_audio_get_eld, it66121_audio_codec_ops, and
it66121_audio_codec_init functions are removed as the framework handles
these responsibilities.
Suggested-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Sen Wang <sen@ti.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://patch.msgid.link/20260318154636.3230454-1-sen@ti.com
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
On error we free aggr->lookups->dev_id before removing the entry from
the lookup table. If a concurrent thread calls gpiod_find() before we
remove the entry, it could iterate over the list and call
gpiod_match_lookup_table() which unconditionally dereferences dev_id
when calling strcmp(). Reverse the order of cleanup.
Fixes: 86f162e73d ("gpio: aggregator: introduce basic configfs interface")
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260520084911.27938-1-bartosz.golaszewski@oss.qualcomm.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
We check the padding of other uAPI v2 structures but not that of line
config attributes. For used attributes: check if their padding is
zeroed, for unused: check if the entire structure is zeroed.
Fixes: 3c0d9c635a ("gpiolib: cdev: support GPIO_V2_GET_LINE_IOCTL and GPIO_V2_LINE_GET_VALUES_IOCTL")
Reviewed-by: Kent Gibson <warthog618@gmail.com>
Link: https://patch.msgid.link/20260521-gpio-cdev-attr-padding-check-v3-1-ec3bcbe2e358@oss.qualcomm.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Validate rx-internal-delay-ps and tx-internal-delay-ps against the
hardware capabilities of the EIC7700 MAC.
The programmable RGMII delay supports 20 ps steps and a maximum value of
2540 ps. The driver previously accepted arbitrary values and silently
truncated unsupported settings when converting them to hardware units.
As a result, invalid device tree values could lead to unexpected delay
programming and incorrect RGMII timing.
Reject delay values that are not multiples of 20 ps or exceed the
supported hardware range.
Fixes: ea77dbbdbc ("net: stmmac: add Eswin EIC7700 glue driver")
Signed-off-by: Zhi Li <lizhi2@eswincomputing.com>
Link: https://patch.msgid.link/20260518022214.507-1-lizhi2@eswincomputing.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The EIC7700 MAC implements programmable RGMII delay adjustment with a
granularity of 20 ps per hardware step.
The driver previously converted rx-internal-delay-ps and
tx-internal-delay-ps values using a 100 ps step size, resulting in
incorrect delay programming.
Update the conversion to use the correct 20 ps granularity so the
programmed delay matches the values described in the device tree.
Fixes: ea77dbbdbc ("net: stmmac: add Eswin EIC7700 glue driver")
Signed-off-by: Zhi Li <lizhi2@eswincomputing.com>
Link: https://patch.msgid.link/20260518022156.484-1-lizhi2@eswincomputing.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Clear the TXD and RXD delay control registers during EIC7700 DWMAC
initialization.
These registers may retain values programmed by the bootloader. If left
unchanged, residual delays can alter the effective RGMII timing seen by
the MAC and override the configuration described by the device tree.
This may violate the expected RGMII timing model and can cause link
instability or prevent the Ethernet controller from operating correctly.
Explicitly clearing these registers ensures that the MAC delay settings
are determined solely by the kernel configuration.
The corresponding register offsets are optional, and the registers are
only cleared when the offsets are provided in the device tree.
Fixes: ea77dbbdbc ("net: stmmac: add Eswin EIC7700 glue driver")
Signed-off-by: Zhi Li <lizhi2@eswincomputing.com>
Link: https://patch.msgid.link/20260518022137.464-1-lizhi2@eswincomputing.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Fix the initialization ordering of the HSP CSR configuration in the
EIC7700 DWMAC glue driver.
The HSP CSR registers control MAC-side RGMII delay behavior and must
only be accessed after the corresponding clocks are enabled. The
previous implementation could trigger register access before clock
enablement, leading to undefined behavior depending on boot state.
Move the HSP CSR configuration into the post-clock-enable initialization
path to ensure all register accesses occur under valid clock domains.
This change ensures deterministic initialization and prevents
clock-dependent register access failures during probe or resume.
Fixes: ea77dbbdbc ("net: stmmac: add Eswin EIC7700 glue driver")
Signed-off-by: Zhi Li <lizhi2@eswincomputing.com>
Link: https://patch.msgid.link/20260518022055.444-1-lizhi2@eswincomputing.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Document two optional cells in eswin,hsp-sp-csr for the TXD and RXD
delay control register offsets.
These registers are used by the driver to clear any residual delay
configuration left by the bootloader, ensuring that MAC-side RGMII delay
settings are applied solely according to the kernel configuration.
Add a reference to the EIC7700X SoC Technical Reference Manual for
background information about the HSP CSR block.
Fixes: 888bd0eca9 ("dt-bindings: ethernet: eswin: Document for EIC7700 SoC")
Signed-off-by: Zhi Li <lizhi2@eswincomputing.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://patch.msgid.link/20260518022023.427-1-lizhi2@eswincomputing.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The exynos-combiner driver uses a regular spinlock to protect access to
the combiner interrupt status register in combiner_handle_cascade_irq(),
which is invoked in hard interrupt context as a chained interrupt handler.
When PREEMPT_RT is enabled on ARM, regular spinlock is converted to a
sleeping lock (mutex-based), which must not be used in atomic context
such as hard interrupt handlers.
Switch the irq_controller_lock to raw_spinlock, which remains a true
non-sleeping spinlock even under PREEMPT_RT.
Fixes: a900e5d997 ("ARM: exynos: move exynos4210-combiner to drivers/irqchip")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Thomas Gleixner <tglx@kernel.org>
Replace the driver local defines with the shared constants defined in the
<linux/hdmi.h> header for the minimum and maximum TMDS character rates.
Suggested-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patch.msgid.link/20260520144424.1633354-9-javierm@redhat.com
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Replace the driver local defines with the shared constants defined in the
<linux/hdmi.h> header for the minimum and maximum TMDS character rates.
Suggested-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patch.msgid.link/20260520144424.1633354-8-javierm@redhat.com
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Replace the 165000000 magic number with the shared constant defined
in the <linux/hdmi.h> header.
The old comment referenced "HDMI <= 1.2" but 165 MHz is actually
the maximum TMDS character rate defined by the HDMI 1.0 spec.
Suggested-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Chen-Yu Tsai <wens@kernel.org>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patch.msgid.link/20260520144424.1633354-7-javierm@redhat.com
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Replace the 340000000 and 165000000 magic numbers with the shared
constants defined in the <linux/hdmi.h> header.
Suggested-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patch.msgid.link/20260520144424.1633354-6-javierm@redhat.com
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Replace the driver local INNO_HDMI_MIN_TMDS_CLOCK define with the shared
constant defined in the <linux/hdmi.h> header.
Suggested-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patch.msgid.link/20260520144424.1633354-5-javierm@redhat.com
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Replace the driver local HDMI14_MAX_TMDSCLK define with the shared
constant defined in the <linux/hdmi.h> header.
The local define incorrectly referenced HDMI 1.4, but the 340 MHz
maximum TMDS character rate was actually introduced in HDMI 1.3.
Suggested-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patch.msgid.link/20260520144424.1633354-4-javierm@redhat.com
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Replace the driver local HDMI14_MAX_TMDSCLK define with the shared
constant defined in the <linux/hdmi.h> header.
The local define incorrectly referenced HDMI 1.4, but the 340 MHz
maximum TMDS character rate was actually introduced in HDMI 1.3.
Suggested-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patch.msgid.link/20260520144424.1633354-3-javierm@redhat.com
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Several DRM drivers already define their own constants for minimum and
maximum TMDS character rates.
By defining common rate constants in a shared header, drivers can just use
them instead of having driver local define macros or use magic numbers.
The values defined in the <linux/hdmi.h> header correspond to maximum TMDS
character rates defined by each HDMI specification version:
- HDMI_TMDS_CHAR_RATE_MIN_HZ: 25 MHz (minimum for all versions)
- HDMI_1_0_TMDS_CHAR_RATE_MAX_HZ: 165 MHz (HDMI 1.0 maximum)
- HDMI_1_3_TMDS_CHAR_RATE_MAX_HZ: 340 MHz (HDMI 1.3 maximum)
- HDMI_2_0_TMDS_CHAR_RATE_MAX_HZ: 600 MHz (HDMI 2.0 maximum)
Suggested-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patch.msgid.link/20260520144424.1633354-2-javierm@redhat.com
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
The dw_hdmi-rockchip driver validates pixel clock rates against the
HDMI PHY's internal clock provider on certain SoCs like RK3328.
This is currently achieved by dereferencing hdmi->phy->dev.of_node
to obtain the provider node, which violates the Generic PHY API's
encapsulation (the goal is for struct phy to be an opaque pointer
with a hidden definition, to be interacted with only using API
functions or NULL pointer checks, for the case where optional variants
of phy_get() did not find a PHY).
Refactor dw_hdmi_rockchip_bind() to perform a manual phandle lookup
on the "hdmi" PHY index within the controller's DT node. This provides
a parallel path to the clock provider's OF node without relying on the
internal structure of the struct phy handle.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20260505100523.1922388-16-vladimir.oltean@nxp.com
Two frag-transfer helpers (__pskb_copy_fclone() and skb_shift()) fail
to propagate the SKBFL_SHARED_FRAG bit in skb_shinfo()->flags when
moving frags from source to destination. __pskb_copy_fclone() defers
the rest of the shinfo metadata to skb_copy_header() after copying
frag descriptors, but that helper only carries over gso_{size,segs,
type} and never touches skb_shinfo()->flags; skb_shift() moves frag
descriptors directly and leaves flags untouched. As a result, the
destination skb keeps a reference to the same externally-owned or
page-cache-backed pages while reporting skb_has_shared_frag() as
false.
The mismatch is harmful in any in-place writer that uses
skb_has_shared_frag() to decide whether shared pages must be detoured
through skb_cow_data(). ESP input is one such writer (esp4.c,
esp6.c), and a single nft 'dup to <local>' rule -- or any other
nf_dup_ipv4() / xt_TEE caller -- is enough to land a pskb_copy()'d
skb in esp_input() with the marker stripped, letting an unprivileged
user write into the page cache of a root-owned read-only file via
authencesn-ESN stray writes.
Set SKBFL_SHARED_FRAG on the destination whenever frag descriptors
were actually moved from the source. skb_copy() and skb_copy_expand()
share skb_copy_header() too but linearize all paged data into freshly
allocated head storage and emerge with nr_frags == 0, so
skb_has_shared_frag() returns false on its own; they need no change.
The same omission exists in skb_gro_receive() and skb_gro_receive_list().
The former moves the incoming skb's frag descriptors into the
accumulator's last sub-skb via two paths (a direct frag-move loop and
the head_frag + memcpy path); the latter chains the incoming skb whole
onto p's frag_list. Downstream skb_segment() reads only
skb_shinfo(p)->flags, and skb_segment_list() reuses each sub-skb's
shinfo as the nskb -- both p and lp must carry the marker.
The same omission also exists in tcp_clone_payload(), which builds an
MTU probe skb by moving frag descriptors from skbs on sk_write_queue
into a freshly allocated nskb. The helper falls into the same family
and warrants the same fix for consistency; no TCP TX-side in-place
writer is currently known to reach a user page through this gap, but
a future consumer depending on the marker would regress silently.
The same omission exists in skb_segment(): the per-iteration flag
merge takes only head_skb's flag, and the inner switch that rebinds
frag_skb to list_skb on head_skb-frags exhaustion does not fold the
new frag_skb's flag into nskb. Fold frag_skb's flag at both sites
so segments drawing frags from frag_list members carry the marker.
Fixes: cef401de7b ("net: fix possible wrong checksum generation")
Fixes: f4c50a4034 ("xfrm: esp: avoid in-place decrypt on shared skb frags")
Suggested-by: Sabrina Dubroca <sd@queasysnail.net>
Suggested-by: Sultan Alsawaf <sultan@kerneltoast.com>
Suggested-by: Ben Hutchings <ben@decadent.org.uk>
Suggested-by: Lin Ma <malin89@huawei.com>
Suggested-by: Jingguo Tan <tanjingguo@huawei.com>
Suggested-by: Aaron Esau <aaron1esau@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hyunwoo Kim <imv4bel@gmail.com>
Tested-by: Rajat Gupta <rajat.gupta@oss.qualcomm.com>
Link: https://patch.msgid.link/ageeJfJHwgzmKXbh@v4bel
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
pca953x_resume() returns 0 when regulator_enable() fails, dropping
the real error code and masking the failure as a successful resume.
The caller then proceeds as if the chip is powered, while the
regulator is in fact disabled.
Return ret so PM core sees the actual failure.
Signed-off-by: Stepan Ionichev <sozdayvek@gmail.com>
Link: https://patch.msgid.link/20260520110504.13969-1-sozdayvek@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Blamed commit moved the TIME_WAIT-derived ISN from the skb control
block to a per-CPU variable, assuming the value would always be consumed
by tcp_conn_request() for the same packet that wrote it. That assumption
is violated by multiple drop paths between the producer
(__this_cpu_write(tcp_tw_isn, isn) in tcp_v{4,6}_rcv()) and the consumer
(tcp_conn_request()):
- min_ttl / min_hopcount check
- xfrm policy check
- tcp_inbound_hash() MD5/AO mismatch
- tcp_filter() eBPF/SO_ATTACH_FILTER drop
- th->syn && th->fin discard in tcp_rcv_state_process() TCP_LISTEN
- psp_sk_rx_policy_check() in tcp_v{4,6}_do_rcv()
- tcp_checksum_complete() in tcp_v{4,6}_do_rcv()
- tcp_v{4,6}_cookie_check() returning NULL
When a packet is dropped on any of these paths, tcp_tw_isn is left set.
The next SYN processed on the same CPU then consumes the non zero value in
tcp_conn_request(), receiving a potentially predictable ISN.
This patch moves back tcp_tw_isn to skb->cb[], getting rid of the per-cpu
variable.
Note that tcp_v{4,6}_fill_cb() do not set it.
Very litle impact on overall code size/complexity:
$ scripts/bloat-o-meter -t vmlinux.old vmlinux.new
add/remove: 0/0 grow/shrink: 2/1 up/down: 8/-15 (-7)
Function old new delta
tcp_v6_rcv 3038 3042 +4
tcp_v4_rcv 3035 3039 +4
tcp_conn_request 2938 2923 -15
Total: Before=24436060, After=24436053, chg -0.00%
Fixes: 41eecbd712 ("tcp: replace TCP_SKB_CB(skb)->tcp_tw_isn with a per-cpu field")
Reported-by: Chris Mason <clm@meta.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20260519084611.2485277-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
vmci_transport_recv_connecting_server() returned err = 0 for a peer
RST in its default switch arm:
err = pkt->type == VMCI_TRANSPORT_PACKET_TYPE_RST ? 0 : -EINVAL;
That made vmci_transport_recv_listen() skip vsock_remove_pending(),
leaving the pending socket on the listener's pending_links with
sk_state = TCP_CLOSE while destroy: still dropped the explicit
reference taken before schedule_delayed_work().
One second later vsock_pending_work() observed is_pending=true and
performed full cleanup: vsock_remove_pending() then the two trailing
sock_put(sk) calls -- the first reached refcount 0 and __sk_freed
the socket, and the second wrote into the freed object:
BUG: KASAN: slab-use-after-free in refcount_warn_saturate
Write of size 4 at addr ffff88800b1cac80 by task kworker
Workqueue: events vsock_pending_work
Treat peer RST like any other unexpected packet type (err = -EINVAL).
All destroy: arms now return err < 0, so vmci_transport_recv_listen()
removes pending from pending_links synchronously and
vsock_pending_work() takes the is_pending=false / !rejected branch,
dropping only its own work reference. This also closes the
multi-packet race Sashiko reported on v2: pending is removed from
the list before any subsequent packet can find it.
The pre-existing sk_acceptq_removed() gap on the err < 0 path of
vmci_transport_recv_listen() that Sashiko also noted is not
introduced or changed by this patch.
Tested on lts-6.12.79 with KASAN: 52/100 unpatched -> 0/100 patched.
Fixes: d021c34405 ("VSOCK: Introduce VM Sockets")
Cc: stable@vger.kernel.org
Signed-off-by: Minh Nguyen <minhnguyen.080505@gmail.com>
Acked-by: Bryan Tan <bryan-bt.tan@broadcom.com>
Link: https://patch.msgid.link/20260519102310.237181-1-minhnguyen.080505@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If zl3073x_dpll_pin_register() fails, the allocated pin is not yet
added to zldpll->pins list. The error path calls
zl3073x_dpll_pins_unregister() which only iterates pins on the list,
so the current pin is leaked. Free the pin before jumping to the error
label.
Additionally move the pin->dpll_pin = NULL assignment in
zl3073x_dpll_pin_register() from err_register to the common
err_pin_get path. When dpll_pin_get() fails, pin->dpll_pin holds an
ERR_PTR value. Without this fix the subsequent zl3073x_dpll_pin_free()
would trigger a spurious WARN because it checks pin->dpll_pin for
non-NULL.
Fixes: 75a71ecc24 ("dpll: zl3073x: Register DPLL devices and pins")
Reviewed-by: Petr Oros <poros@redhat.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Link: https://patch.msgid.link/20260519132205.161847-1-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It turns out ip_rt_bug() can be called more than expected.
syzbot will still panic (because of panic_on_warn=1), but non debug
kernels will no longer die while repeating stack traces on the console.
Fixes: c378a9c019 ("ipv4: Give backtrace in ip_rt_bug().")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Jiayuan Chen <jiayuan.chen@linux.dev>
Link: https://patch.msgid.link/20260519193248.4018872-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
