We should stick to mac80211's flow to start / stop beaconing. This
allows to stop beaconing before we remove the BIGTK.
Note that the start and stop beaconing flows are not exactly symmetric.
When we start beaconing, we just update the beacon template. We assume
that mac80211 won't update the beacons, if we're not supposed to be
sending it.
Also note that we now send the beacon template after the broadcast
station was added to the firmware: the broadcast station is added in
the start_ap() flow, while the beacon template is now added in the
link_changed() flow which happens later. This is not what we did
before this patch, but this sequence is supported by the firmware as
well.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://patch.msgid.link/20260511203428.cf10e5754171.I8022517c6c5aedb4b56fba30a5545de8f62dddbe@changeid
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
The max_channel_switch_time in wiphy_nan_capa is in microseconds, but
the value was set to 4, which is only 4 microseconds instead of the
intended 4 milliseconds.
Fix by using 4 * USEC_PER_MSEC.
Signed-off-by: Israel Kozitz <israel.kozitz@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Link: https://patch.msgid.link/20260510234534.cb3c05e5d334.I89d9f336aaf388c6e48769de5fe1e5db19295057@changeid
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Frames that are sent to an NMI station are always NAN management frames.
Therefore there is no need to configure TLC for such a station.
Always use host rate for the frames going to that station.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20260510234534.fb7272ddbb45.I843dba36f52363bc7e9c81f937547ead12147539@changeid
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
The firmware requires links for NAN which mac80211 doesn't use,
so introduce a new NAN link data structure that the driver has
for itself only, and handle the link command sending code for
NAN using this data structure, most of the bss_conf data isn't
used for NAN anyway, so those structures aren't useful.
With that, add, activate, deactivate or remove links depending
on the local NAN schedule updates.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Co-developed-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260510234534.39ee3533ef30.I81ff6dc02e912396040f922e21888fd94b3c26e6@changeid
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Until now we maintained the NAN vif in the driver only. The fw used the
AUX MAC for sync and discovery operations.
But when we want to configure a local schedule, we need to add the MAC
first.
NAN_DATA interfaces are not added to the FW. Instead, the local
address of these interfaces are configured to the FW via the NAN MAC.
Add the add/remove/update operations for the NAN interface, and fill the
NAN special parameters in it.
Note that this doesn't fully implement the schedule change, but only the
addition/removal of the NAN MAC. The full schedule management
implementation will come in a later patch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Co-developed-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260510234534.dd12944c140b.I3578198660a533faf9f6a94432ef2114f4a9dfae@changeid
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
While NAN stations have the deflink link STA and that even
carries their information, having link STAs mostly implies
having real links, and NAN muddies that by having stations
with deflink carrying their capabilities and links at the
NAN level, but no link stations corresponding to NAN links.
Separate out the data needed to build TLC commands into a
new struct iwl_mld_tlc_sta_capa data structure so that the
whole data usage in the TLC code is clarified and we won't
make assumptions, say about being able to look up the link
of an interface from the (NAN) link sta correctly, which
would result in a link but not with a chanctx.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20260510234534.2c6589aab9db.I01729ec8be4687884831fc8761bf3fd8bba83056@changeid
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Copy the HT, VHT and HE capabilities from the sbands:
- The HT capabilities from the 2.4 GHz sband (there is no difference
between the bands anyway).
- The VHT capabilities from the 5 GHz sband, obviously.
- The HE capabilities from the 2.4 GHz and for NL80211_IFTYPE_STATION.
Fix it up to include also the needed 5 GHz bits.
For HE, there are bits that are band-dependent and iftype-dependent. For
those set to what makes most sense, and leave a comment to re-visit.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20260510234534.3a5e5251dbaf.I566e1749cd17baa672bdd43712114e434f810a69@changeid
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Three BA session handlers use ffs(ba_data->sta_mask) - 1 to derive a
station ID without checking that sta_mask is non-zero. When sta_mask is
zero, ffs() returns 0 and the subtraction wraps to 0xFFFFFFFF, causing
an out-of-bounds access on fw_id_to_link_sta[].
Add WARN_ON_ONCE(!ba_data->sta_mask) guards before each ffs() call,
consistent with the existing check in iwl_mld_ampdu_rx_start().
Reported-by: Yuhao Jiang <danisjiang@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Junrui Luo <moonafterrain@outlook.com>
Link: https://patch.msgid.link/SYBPR01MB788115C6CE873271A9A15A25AF51A@SYBPR01MB7881.ausprd01.prod.outlook.com
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Remove header files that are included but provide no symbols,
types, or macros used by the including translation unit.
In iwl-trans.c, fw/api/tx.h defines TX command structures
(iwl_tx_cmd, iwl_tx_resp, TX_CMD_* flags) used by the PCIe TX
path, not by the transport core itself. Similarly, iwl-fh.h
defines Flow Handler register addresses and DMA-related constants
(FH_*, RFH_*, TFD_*) that are consumed by PCIe-specific code,
none of which are referenced in iwl-trans.c.
In iwl-nvm-parse.c, fw/acpi.h defines ACPI/SAR/GEO/PPAG
interfaces (iwl_acpi_*, iwl_sar_*, iwl_geo_*). No references to
any of these interfaces exist in this file.
Signed-off-by: Jay Ng <jayng9663@gmail.com>
Link: https://patch.msgid.link/20260408034413.1875915-1-jayng9663@gmail.com
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
iwl_mvm_ptp_remove() calls cancel_delayed_work_sync() only after
ptp_clock_unregister() and clearing ptp_data state (ptp_clock,
ptp_clock_info, last_gp2).
This creates a race where the delayed work iwl_mvm_ptp_work() can
execute between ptp_clock_unregister() and cancel_delayed_work_sync(),
observing partially cleared PTP state.
Move cancel_delayed_work_sync() before ptp_clock_unregister() to
ensure the delayed work is fully stopped before any PTP cleanup
begins.
Cc: stable@vger.kernel.org
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Signed-off-by: Junjie Cao <junjie.cao@intel.com>
Link: https://patch.msgid.link/20260212125035.1345718-1-junjie.cao@intel.com
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
iwl_mld_ptp_remove() calls cancel_delayed_work_sync() only after
ptp_clock_unregister() and clearing ptp_data state (ptp_clock,
last_gp2, wrap_counter).
This creates a race where the delayed work iwl_mld_ptp_work() can
execute between ptp_clock_unregister() and cancel_delayed_work_sync(),
observing partially cleared PTP state.
Move cancel_delayed_work_sync() before ptp_clock_unregister() to
ensure the delayed work is fully stopped before any PTP cleanup
begins.
Cc: stable@vger.kernel.org
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Signed-off-by: Junjie Cao <junjie.cao@intel.com>
Link: https://patch.msgid.link/20260212125035.1345718-2-junjie.cao@intel.com
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
The Prism54 SPI driver hardcodes GPIO numbers and expects users to
pass them as module parameters, apparently a relic from its life as a
staging driver. This works because there is only one user, the Nokia
N8x0 tablet.
Convert this to the gpio descriptor interface and DT based probing
to improve this and simplify the code at the same time.
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Reviewed-by: Linus Walleij <linusw@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Link: https://patch.msgid.link/20260507212451.3333185-3-arnd@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The SPI version of Prism54 was sold under a couple of different
names and supported by the Linux p54spi driver, but there was
never a DT binding for it.
Document the four known names of this device and the properties
that are sufficient for its use on the Nokia N8x0 tablet.
As I don't have this hardware or documentation for it, this is
purely based on existing usage in the driver.
Link: https://lore.kernel.org/all/e8dc9acb-6f85-e0a9-a145-d101ca6da201@gmail.com/
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://patch.msgid.link/20260507212451.3333185-2-arnd@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ieee80211_key_link() rejects pairwise key installation when the
cipher differs from the existing PTK. Per Wi-Fi Aware version 4.0
section 7.4, the ND-TKSA between the same NDI pair shall be updated
when a new NDP requires a stronger cipher suite.
Exempt NL80211_IFTYPE_NAN_DATA from the same-cipher enforcement so
the PTK can be replaced with a different cipher.
Signed-off-by: Daniel Gabay <daniel.gabay@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260515142736.3188a47a23bf.I5fba3a111ffe054b46928aefa5c2d763fef51d4d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Do not declare support for Extended Key ID for NAN, as defined in
section 7.4 in the WiFi Aware specification v4.0 (in order to support
security association upgrade).
Fixes: eaa7ce66c3 ("wifi: mac80211_hwsim: Fix possible NULL dereference")
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260515141442.365ca3ab29f9.Ib435168dcc1d7d8719a5612109035ca1950967ed@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case reconfiguration of NAN fails, we call
ieee80211_handle_reconfig_failure, that marks all interfaces as not in
the driver.
Then, at the error path of the reconfig, cfg80211_shutdown_all_interfaces
is called to destroy all the interfaces.
If we have any other interface but the NAN one, for example a BSS
station, then when its state (links, stations) will be removed, we
won't tell the driver about this, because we will think that the
interfaces are not in the driver, and then drivers might remain with
dangling pointers to objects like stations and links (at least for
iwlwifi this is the case).
ieee80211_handle_reconfig_failure is meant to be called after we cleaned
up the state in the driver, there is no reason to call it for NAN
reconfiguration failure.
Fix the code to just warn in such a case, as we do in other error paths
in reconfig where it is too complicated to rewind.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260513182548.6a25f3a0a6ec.I83d1f2a7eed20200a78a62757c6b193e3bab892b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The WiFi Aware specification (v4.0) requires that NAN devices that
support security would also support per station GTK. Thus, allow
per station GTK installation to the driver on NAN Data interfaces.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Tested-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
tested: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260513172418.37a8e259e611.I39bb9f3c1a65a8184124f531c18e121dc123d411@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This doesn't really do anything, but we can advertise it and then
check that the AP can be configured and client can connect, etc.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260512224724.abfd51f480b7.I2024d7fc8067a0fca26234f312937cc764b660f4@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When userspace creates a new hwsim radio with both
HWSIM_ATTR_MULTI_RADIO and HWSIM_ATTR_SUPPORT_NAN_DEVICE,
hwsim_new_radio_nl() sets BIT(NL80211_IFTYPE_NAN_DATA) in
wiphy->interface_modes while configuring the wiphy with
n_radio > 1. This violates the invariant checked in
wiphy_register():
(interface_modes & BIT(NL80211_IFTYPE_NAN_DATA)) &&
(!nan_capa.phy.ht.ht_supported || n_radio > 1)
triggering a WARN reachable from userspace via genetlink.
With panic_on_warn this becomes a denial of service.
Refuse the combination at parse time with -EINVAL and an
extack message, matching the cfg80211 constraint that NAN
is not supported on multi-radio wiphys.
Reported-by: syzbot+2002864e6c6895cb0ac3@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=2002864e6c6895cb0ac3
Fixes: 2c7c70ee7c ("wifi: mac80211_hwsim: enable NAN_DATA interface simulation support")
Tested-by: syzbot+2002864e6c6895cb0ac3@syzkaller.appspotmail.com
Signed-off-by: Deepanshu Kartikey <kartikey406@gmail.com>
Link: https://patch.msgid.link/20260509004628.79446-1-kartikey406@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
init and exit do nothing interesting that module_usb_driver doesn't
already handle. Just use module_usb_driver to simplify the code.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://patch.msgid.link/20260507015457.239807-1-rosenp@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
__ieee80211_recalc_chanctx_min_def() currently does not attempt
to find the min def for S1G widths, meaning the BW will never change.
However, the following call into ieee80211_chan_bw_change() will
lead to a WARN within ieee80211_chan_width_to_rx_bw(). Not only that,
this entire path is geared towards 20MHz based channels, so it doesn't
make sense anyway. For now, return early when calculating the mindef
for S1G channels.
Fixes: d879d4da45 ("wifi: mac80211: clean up initial STA NSS/bandwidth handling")
Signed-off-by: Lachlan Hodges <lachlan.hodges@morsemicro.com>
Link: https://patch.msgid.link/20260506131925.2088353-3-lachlan.hodges@morsemicro.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently there is no S1G STA bandwidth support throughout mac80211
as existing support is all based on 20MHz widths. With the recent
STA NSS/BW handling rework, S1G associations now hit the new WARN within
ieee80211_chan_width_to_rx_bw() as the chandef is not a 20MHz based
width. For now, skip initialisating link_sta->pub->bandwidth for
S1G chandefs to avoid the WARN though this should at some point be
properly implemented since there are vendors that offer differing
maximum bandwidths.
Additionally, currently all S1G hardware out there is 1SS so rather
then introducing new parsing code which wouldn't be used anyway, just
initialise the NSS related fields to 1 and skip initialising the STA
bandwidth for S1G chandefs within ieee80211_sta_init_nss_bw_capa().
Fixes: d879d4da45 ("wifi: mac80211: clean up initial STA NSS/bandwidth handling")
Signed-off-by: Lachlan Hodges <lachlan.hodges@morsemicro.com>
Link: https://patch.msgid.link/20260506131925.2088353-2-lachlan.hodges@morsemicro.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If an interface changes to/from MLD, then all stations related
to it must have been removed first. This is just natural since
we go from having links to not (or vice versa), but not doing
so also causes crashes in debugfs since vif changing to/from
MLD removes the entire debugfs for the vif, including stations.
Delete all stations but warn in this case, other code should
be handling it, in effect fail fast rather than doing a double
free or use-after-free in debugfs.
Link: https://patch.msgid.link/20260505151731.3d7cbb8b952c.I4ce7b536e8af26d7b115e82fd733734446cc56a4@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of being creative with devm, allocate with rt2x00dev by using a
flexible array member. Simplifies code slightly.
It's worth noting that in 25369b2222 , the
proper device was set to the devm call as it seems there was confusion
there.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Link: https://patch.msgid.link/20260430232206.141461-1-rosenp@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-----BEGIN PGP SIGNATURE-----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=bV7l
-----END PGP SIGNATURE-----
Merge tag 'audit-pr-20260513' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit
Pull audit fixes from Paul Moore:
- Correctly log the inheritable capabilities
- Honor AUDIT_LOCKED in the AUDIT_TRIM and AUDIT_MAKE_EQUIV commands
* tag 'audit-pr-20260513' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit:
audit: enforce AUDIT_LOCKED for AUDIT_TRIM and AUDIT_MAKE_EQUIV
audit: fix incorrect inheritable capability in CAPSET records
The 'dumpability' of a task is fundamentally about the memory image of
the task - the concept comes from whether it can core dump or not - and
makes no sense when you don't have an associated mm.
And almost all users do in fact use it only for the case where the task
has a mm pointer.
But we have one odd special case: ptrace_may_access() uses 'dumpable' to
check various other things entirely independently of the MM (typically
explicitly using flags like PTRACE_MODE_READ_FSCREDS). Including for
threads that no longer have a VM (and maybe never did, like most kernel
threads).
It's not what this flag was designed for, but it is what it is.
The ptrace code does check that the uid/gid matches, so you do have to
be uid-0 to see kernel thread details, but this means that the
traditional "drop capabilities" model doesn't make any difference for
this all.
Make it all make a *bit* more sense by saying that if you don't have a
MM pointer, we'll use a cached "last dumpability" flag if the thread
ever had a MM (it will be zero for kernel threads since it is never
set), and require a proper CAP_SYS_PTRACE capability to override.
Reported-by: Qualys Security Advisory <qsa@qualys.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Kees Cook <kees@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
At this time the driver is not listing any speeds
it supports. This should be ETHTOOL_LINK_MODE_100baseT1_Full_BIT
for DP83TC811. Add the missing call for phylib to read the abilities.
Fixes: b753a9faaf ("net: phy: DP83TC811: Introduce support for the DP83TC811 phy")
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Sven Schuchmann <schuchmann@schleissheimer.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260512071949.6218-1-schuchmann@schleissheimer.de
[pabeni@redhat.com: dropped revision history]
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Sashiko points out that if end = 0 (start != 0) the current
code will create a chain link to content type right after
the wrap link:
This would create a chain where the wrap link points directly
to another chain link. The scatterlist API sg_next iterator
does not recursively resolve consecutive chain links.
meaning this is illegal input to crypto.
The wrapping link is unnecessary if end = 0. end is the entry after
the last one used so end = 0 means there's nothing pushed after
the wrap:
end start i
v v v
[ ]...[ ][ d ][ d ][ d ][ d ][rsv for wrap]
Skip the wrapping in this case.
TLS 1.3 can use the "wrapping slot" for it's chaining if end = 0.
This avoids the chain-after-chain.
Move the wrap chaining before marking END and chaining off content
type, that feels like more logical ordering to me, but should not
matter from functional perspective.
Reported-by: Sashiko <sashiko-bot@kernel.org>
Fixes: 9aaaa56845 ("bpf: Sockmap/tls, skmsg can have wrapped skmsg that needs extra chaining")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Link: https://patch.msgid.link/20260511174920.433155-3-kuba@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When an sk_msg scatterlist ring wraps (sg.end < sg.start),
tls_push_record() chains the tail portion of the ring to the head
using sg_chain(). An extra entry in the sg array is reserved for
this:
struct sk_msg_sg {
[...]
/* The extra two elements:
* 1) used for chaining the front and sections when the list becomes
* partitioned (e.g. end < start). The crypto APIs require the
* chaining;
* 2) to chain tailer SG entries after the message.
*/
struct scatterlist data[MAX_MSG_FRAGS + 2];
The current code uses MAX_SKB_FRAGS + 1 as the ring size:
sg_chain(&msg_pl->sg.data[msg_pl->sg.start],
MAX_SKB_FRAGS - msg_pl->sg.start + 1,
msg_pl->sg.data);
This places the chain pointer at
sg_chain(data[start], (MAX_SKB_FRAGS - msg_start + 1) .. =
&data[start] + (MAX_SKB_FRAGS - msg_start + 1) - 1 =
data[start + (MAX_SKB_FRAGS - start + 1) - 1] =
data[MAX_SKB_FRAGS]
instead of the true last entry. This is likely due to a "race" of
the commit under Fixes landing close to
commit 031097d9e0 ("bpf: sk_msg, zap ingress queue on psock down")
Convert to ARRAY_SIZE and drop the data[start] / - start (as suggested
by Sabrina).
Reported-by: 钱一铭 <yimingqian591@gmail.com>
Fixes: 9aaaa56845 ("bpf: Sockmap/tls, skmsg can have wrapped skmsg that needs extra chaining")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://patch.msgid.link/20260511174920.433155-2-kuba@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Danielle Ratson says:
====================
bridge: Add selective forwarding of gratuitous neighbor announcements
The existing neighbor suppression unconditionally suppresses gratuitous
ARPs and unsolicited Neighbor Advertisements, which prevents fast
mobility of hosts between VTEPs.
This series adds a new neigh_forward_grat option that provides
independent control of gratuitous ARP and unsolicited NA forwarding.
When neigh_suppress is enabled but neigh_forward_grat is enabled,
regular neighbor discovery is suppressed while gratuitous announcements
are forwarded.
The implementation marks gratuitous ARPs and unsolicited NAs in
BR_INPUT_SKB_CB during input processing, then checks the per-output-port
neigh_forward_grat setting during flooding. This allows gratuitous
announcements from any input port to be selectively forwarded based on
each output port's individual configuration.
Both port-level control (via IFLA_BRPORT_NEIGH_FORWARD_GRAT) and
per-VLAN control (via BRIDGE_VLANDB_ENTRY_NEIGH_FORWARD_GRAT) are
provided. The default value of OFF preserves existing behavior.
This behavior is in accordance with RFC 9161 (Section 3.6), which
recommends that VTEPs forward gratuitous ARP and unsolicited NA messages
to avoid traffic disruption during host mobility events.
The new attributes use NLA_U8, although the kernel netlink guideline
recommends NLA_U32 as the minimum integer type on the grounds that
alignment makes smaller types equivalent on the wire. For a simple
on/off attribute there is no technical advantage to u32 over u8, and
keeping u8 preserves consistency with all surrounding bridge port
attributes and avoids introducing new helpers alongside the existing
infrastructure.
Patchset overview:
Patch #1: adds uapi headers.
Patches #2-#3: support selective forwarding of gratuitous ARP.
Patches #4-#5: add netlink handling.
Patch #6: adds tests.
Please see iproute related patches in the last 3 commits of:
https://github.com/daniellerts/iproute2
====================
Link: https://patch.msgid.link/20260511065936.4173106-1-danieller@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add tests to validate the neigh_forward_grat bridge option for selective
forwarding of gratuitous neighbor announcements.
The tests verify per-port and per-VLAN control of gratuitous neighbor
announcement forwarding for both IPv4 (gratuitous ARP) and IPv6
(unsolicited NA):
- When neigh_suppress is enabled with neigh_forward_grat off (default),
gratuitous announcements are suppressed
- When neigh_forward_grat is enabled, gratuitous announcements are
forwarded while regular neighbor discovery remains suppressed
For IPv4, use arping to send gratuitous ARP packets. For IPv6, use
mausezahn to craft unsolicited Neighbor Advertisement packets.
For the per-port tests, the IPv4 test exercises the ip link interface,
while the IPv6 test exercises the bridge link interface.
The per-VLAN tests use the bridge interface throughout, as per-VLAN
attributes are only accessible via 'bridge vlan'.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Link: https://patch.msgid.link/20260511065936.4173106-7-danieller@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add netlink handlers for the per-VLAN neigh_forward_grat option via
BRIDGE_VLANDB_ENTRY_NEIGH_FORWARD_GRAT attribute.
The per-VLAN option provides fine-grained control, allowing different
VLANs on the same port to have different gratuitous ARP/unsolicited NA
forwarding behavior.
This enables control via 'bridge' commands:
# bridge vlan set dev eth0 vid 10 neigh_suppress on
# bridge vlan set dev eth0 vid 10 neigh_forward_grat on
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/20260511065936.4173106-6-danieller@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add netlink handlers for the port-level neigh_forward_grat option via
IFLA_BRPORT_NEIGH_FORWARD_GRAT attribute.
The default value of OFF preserves existing behavior, i.e. gratuitous ARP
and unsolicited NA are suppressed when neigh_suppress is enabled. Users can
explicitly set it to ON to allow these packets through.
Example for enabling control via 'bridge link' command:
# bridge link set dev eth0 neigh_suppress on
# bridge link set dev eth0 neigh_forward_grat on
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/20260511065936.4173106-5-danieller@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The existing neighbor suppression unconditionally suppresses gratuitous
ARPs and unsolicited Neighbor Advertisements, which prevents fast
mobility of hosts between VTEPs.
Add the neigh_forward_grat option to allow selective control of gratuitous
neighbor announcements. When neigh_suppress is enabled but
neigh_forward_grat is disabled (default), gratuitous announcements are
suppressed. When neigh_forward_grat is enabled, gratuitous announcements
are forwarded while regular neighbor discovery remains suppressed.
The implementation provides per-output-port control by:
1. Adding a 'grat_arp' flag to BR_INPUT_SKB_CB to mark gratuitous ARPs and
unsolicited NAs.
2. Setting both grat_arp and proxyarp_replied flags in
br_do_proxy_suppress_arp() and br_do_suppress_nd() when gratuitous
packets are detected.
3. Checking neigh_forward_grat per output port during flooding:
- For gratuitous ARPs/NAs: suppress unless the output port has
neigh_forward_grat enabled.
- For regular ARPs/NDs: maintain existing behavior.
This allows gratuitous announcements from any input port to be selectively
forwarded based on each output port's individual neigh_forward_grat
setting, enabling gratuitous neighbor announcements to be flooded to the
VXLAN fabric.
Regular neighbor discovery (ARP requests, NS queries, solicited replies)
remains controlled by neigh_suppress and is unaffected.
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/20260511065936.4173106-4-danieller@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
