As per Wa_16025573575 for PTL/WCL, set the GPIO masks bit before starting
bit-bashing and maintain value through the bit-bashing sequence. After the
bit-bashing sequence is done, clear the GPIO masks bits.
v2:
-Use new helper for display workarounds. (Jani)
-Use a separate if-block for the workaround. (Gustavo)
v3:
-Document the workaround details in intel_display_wa.c
-Extend the workaround to WCL too. (Gustavo)
v4:
-Fix the platform check. (Gustavo)
-Avoid read when preserve bits are 0. (Gustavo)
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Link: https://lore.kernel.org/r/20250715142211.3145299-1-ankit.k.nautiyal@intel.com
Introduce a generic helper to check display workarounds using an enum.
Convert Wa_16023588340 to use the new interface, simplifying WA checks
and making future additions easier.
v2: Use drm_WARN instead of MISSING_CASE and simplify intel_display_wa
macro. (Jani)
v3: Print Missing wa number, instead of enum value. (Gustavo, Jani)
Suggested-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Link: https://lore.kernel.org/r/20250711041901.1607823-2-ankit.k.nautiyal@intel.com
The !in_atomic() check in _wait_for_atomic() triggers on PREEMPT_RT
because the uncore::lock is a spinlock_t and does not disable
preemption or interrupts.
Changing the uncore:lock to a raw_spinlock_t doubles the worst case
latency on an otherwise idle testbox during testing.
Ignore _WAIT_FOR_ATOMIC_CHECK() on PREEMPT_RT.
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@igalia.com>
Link: https://lore.kernel.org/all/20211006164628.s2mtsdd2jdbfyf7g@linutronix.de/
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20250714153954.629393-4-bigeasy@linutronix.de
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
Commit a40c5d727b ("drm/dp: Change AUX DPCD probe address from
DPCD_REV to LANE0_1_STATUS") stopped using the DPCD_REV register for
DPCD probing, since this results in link training failures at least when
using an Intel Barlow Ridge TBT hub at UHBR link rates (the
DP_INTRA_HOP_AUX_REPLY_INDICATION never getting cleared after the failed
link training). Since accessing DPCD_REV during link training is
prohibited by the DP Standard, LANE0_1_STATUS (0x202) was used instead,
as it falls within the Standard's valid register address range
(0x102-0x106, 0x202-0x207, 0x200c-0x200f, 0x2216) and it fixed the link
training on the above TBT hub.
However, reading the LANE0_1_STATUS register also has a side-effect at
least on a Novatek eDP panel, as reported on the Closes: link below,
resulting in screen flickering on that panel. One clear side-effect when
doing the 1-byte probe reads from LANE0_1_STATUS during link training
before reading out the full 6 byte link status starting at the same
address is that the panel will report the link training as completed
with voltage swing 0. This is different from the normal, flicker-free
scenario when no DPCD probing is done, the panel reporting the link
training complete with voltage swing 2.
Using the TRAINING_PATTERN_SET register for DPCD probing doesn't have
the above side-effect, the panel will link train with voltage swing 2 as
expected and it will stay flicker-free. This register is also in the
above valid register range and is unlikely to have a side-effect as that
of LANE0_1_STATUS: Reading LANE0_1_STATUS is part of the link training
CR/EQ sequences and so it may cause a state change in the sink - even if
inadvertently as I suspect in the case of the above Novatek panel. As
opposed to this, reading TRAINING_PATTERN_SET is not part of the link
training sequence (it must be only written once at the beginning of the
CR/EQ sequences), so it's unlikely to cause any state change in the
sink.
As a side-note, this Novatek panel also lacks support for TPS3, while
claiming support for HBR2, which violates the DP Standard (the Standard
mandating TPS3 for HBR2).
Besides the Novatek panel (PSR 1), which this change fixes, I also
verified the change on a Samsung (PSR 1) and an Analogix (PSR 2) eDP
panel as well as on the Intel Barlow Ridge TBT hub.
Note that in the drm-tip tree (targeting the v6.17 kernel version) the
i915 and xe drivers keep DPCD probing enabled only for the panel known
to require this (HP ZR24w), hence those drivers in drm-tip are not
affected by the above problem.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Fixes: a40c5d727b ("drm/dp: Change AUX DPCD probe address from DPCD_REV to LANE0_1_STATUS")
Reported-and-tested-by: Paul Menzel <pmenzel@molgen.mpg.de>
Closes: https://gitlab.freedesktop.org/drm/i915/kernel/-/issues/14558
Reviewed-by: Jonathan Cavitt <jonathan.cavitt@intel.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://lore.kernel.org/r/20250708212331.112898-1-imre.deak@intel.com
Some ICL/TGL platforms with combo PHY ports suffer from signal integrity
issues at HBR3. While certain systems include a Parade PS8461 mux to
mitigate this, its presence cannot be reliably detected. Furthermore,
broken or missing VBT entries make it unsafe to rely on VBT for enforcing
link rate limits.
To address this introduce a device specific quirk to cap the eDP link rate
to HBR2 (540000 kHz). This will override any higher advertised rates from
the sink or DPCD for specific devices.
Currently, the quirk is added for Dell XPS 13 7390 2-in-1 which is reported
in gitlab issue #5969 [1].
[1] https://gitlab.freedesktop.org/drm/i915/kernel/-/issues/5969
v2: Align the quirk with the intended quirk name and refactor the
condition to use min(). (Jani)
v3: Use condition `rate > 540000`. Drop extra parentheses. (Ville)
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Closes: https://gitlab.freedesktop.org/drm/i915/kernel/-/issues/5969
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://lore.kernel.org/r/20250710052041.1238567-3-ankit.k.nautiyal@intel.com
This reverts commit 584cf613c2.
Commit 584cf613c2 ("drm/i915/dp: Reject HBR3 when sink doesn't support
TPS4") introduced a blanket rejection of HBR3 link rate when the sink does
not support TPS4.
While this was intended to address instability observed on certain eDP
panels [1], there seem to be edp panels that do not follow the
specification. These eDP panels do not advertise TPS4 support, but require
HBR3 to operate at their fixed native resolution [2].
As a result, the change causes blank screens on such panels. Apparently,
Windows driver does not enforce this restriction, and the issue is not seen
there.
Therefore, revert the commit to restore functionality for such panels,
and align behaviour with Windows driver.
[1] https://gitlab.freedesktop.org/drm/i915/kernel/-/issues/5969
[2] https://gitlab.freedesktop.org/drm/i915/kernel/-/issues/14517
v2: Update the commit message with better justification. (Ville)
Closes: https://gitlab.freedesktop.org/drm/i915/kernel/-/issues/14517
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://lore.kernel.org/r/20250710052041.1238567-2-ankit.k.nautiyal@intel.com
We only support resolution up to 4k for single pipe when using
YUV420 format so we prune these modes and restrict the plane size
at src. This is because pipe scaling will not support YUV420 scaling
for hwidth > 4096.
--v2
-Use output format to check [Ville]
-Add Bspec references
-Modify commit messge to point to why this is needed
--v3
-Use a function skl_scaler_mode_valid which is routed throug
intel_pfit_mode_valid [Ville]
-Combine the check conditons [Jonathan]
--v4
-mode_valid functions should return drm_mode_status [Jani]
--v5
-Use skl_scaler_max_src_size [Ankit]
Bspec: 49247, 50441
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Jonathan Cavitt <jonathan.cavitt@intel.com> #v2
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://lore.kernel.org/r/20250708043328.1086192-2-suraj.kandpal@intel.com
skl_scaler_max_src_size has really no use of intel_crtc other than
deriving intel_display. Let's just pass intel_display to it directly.
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://lore.kernel.org/r/20250708043328.1086192-1-suraj.kandpal@intel.com
It turns out that the fixup from vlv_fixup_mipi_sequences() is necessary
for some DSI panel's with version 2 mipi-sequences too.
Specifically the Acer Iconia One 8 A1-840 (not to be confused with the
A1-840FHD which is different) has the following sequences:
BDB block 53 (1284 bytes) - MIPI sequence block:
Sequence block version v2
Panel 0 *
Sequence 2 - MIPI_SEQ_INIT_OTP
GPIO index 9, source 0, set 0 (0x00)
Delay: 50000 us
GPIO index 9, source 0, set 1 (0x01)
Delay: 6000 us
GPIO index 9, source 0, set 0 (0x00)
Delay: 6000 us
GPIO index 9, source 0, set 1 (0x01)
Delay: 25000 us
Send DCS: Port A, VC 0, LP, Type 39, Length 5, Data ff aa 55 a5 80
Send DCS: Port A, VC 0, LP, Type 39, Length 3, Data 6f 11 00
...
Send DCS: Port A, VC 0, LP, Type 05, Length 1, Data 29
Delay: 120000 us
Sequence 4 - MIPI_SEQ_DISPLAY_OFF
Send DCS: Port A, VC 0, LP, Type 05, Length 1, Data 28
Delay: 105000 us
Send DCS: Port A, VC 0, LP, Type 05, Length 2, Data 10 00
Delay: 10000 us
Sequence 5 - MIPI_SEQ_ASSERT_RESET
Delay: 10000 us
GPIO index 9, source 0, set 0 (0x00)
Notice how there is no MIPI_SEQ_DEASSERT_RESET, instead the deassert
is done at the beginning of MIPI_SEQ_INIT_OTP, which is exactly what
the fixup from vlv_fixup_mipi_sequences() fixes up.
Extend it to also apply to v2 sequences, this fixes the panel not working
on the Acer Iconia One 8 A1-840.
Closes: https://gitlab.freedesktop.org/drm/i915/kernel/-/issues/14605
Signed-off-by: Hans de Goede <hansg@kernel.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://lore.kernel.org/r/20250703143824.7121-1-hansg@kernel.org
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Prefer the register read specific wait function over i915 wait_for_us().
The existing condition is quite complicated. Simplify by checking for
requesters first, and determine timeout based on that. Refresh
requesters in case of timeouts, should one have popped up during the
wait. The downside is that this does not cut the wait short if
requesters show up *during* the wait, but we're talking about 1 ms so
shouldn't be an issue.
v2: Refresh requesters only if there were none before (Imre)
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://lore.kernel.org/r/20250626192632.2330349-1-jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
With the switch to an unordered workqueue dedicated to display, we've
stopped using struct drm_i915_private in a number of places, and can
drop the dependencies on i915_drv.h.
Cc: Luca Coelho <luciano.coelho@intel.com>
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://lore.kernel.org/r/20250626101636.1896365-1-jani.nikula@intel.com
Currently, Ultrajoiner is supported only on Xe2_HPD.
Update the HAS_ULTRAJOINER macro to reflect the same.
v2: Clarify the commit message to specify platform. (Jani)
Bspec: 69556
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Karthik B S <karthik.b.s@intel.com>
Link: https://lore.kernel.org/r/20250611053039.377695-1-ankit.k.nautiyal@intel.com
If CONFIG_DRM_XE_DISPLAY is set, the xe module can only be built as
module to avoid duplicate symbols from i915. The interface for pcode was
added without considering that, so the build breaks if both xe and i915
are built-in.
Since the intel_pcode_* functions should only be called from the display
side (xe side should call the xe interface directly) and there's already
a protection in Kconfig to avoid the problematic configuration, ifdef it
out in case CONFIG_DRM_XE_DISPLAY is disabled.
Closes: https://lore.kernel.org/r/3667a992-a24b-4e49-aab2-5ca73f2c0a56@infradead.org
Fixes: d9465cc8ac ("drm/xe/pcode: add struct drm_device based interface")
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://lore.kernel.org/r/20250627-xe-kunit-v2-1-756fe5cd56cf@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Implement the driver side of Wa_18034343758, which is supposed to
prevent the DSB and DMC from accessing registers in parallel, and
thus potentially corrupting the registers due to a hardware issue
(which should be fixed in PTL-B0).
The w/a sequence goes as follows:
DMC starts the DSB
| \
DMC halts itself | DSB waits a while for DMC to have time to halt
. | DSB executes normally
. | DSB unhalts the DMC at the very end
. /
DMC resumes execution
v2: PTL-B0+ firmware no longer has the w/a since the hw got fixed
v3: Do the w/a on all PTL for now since we only have the A0 firmware
binaries which issues the halt instructions unconditionally
v4: PTL DMC binaries do in fact have the A0 vs. B0 split, so skip
the w/a on PTL-B0+
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250624170049.27284-7-ville.syrjala@linux.intel.com
Support commits via the flip queue (as opposed to DSB or MMIO).
As it's somewhat unknown if we can actually use it is currently
gated behind the new use_flipq modparam, which defaults to disabled.
The implementation has a bunch of limitations that would need
real though to solve:
- disabled when PSR is used
- disabled when VRR is used
- color management updates not performed via the flip queue
v2: Don't use flip queue if there is no dmc
v3: Use intel_flipq_supported()
v3: Configure PKG_C_LATENCY appropriately
Ignore INT_VECTOR if there is a real PIPEDMC interrupt
(nothing in the hw appears to clear INT_VECTOR)
v4: Leave added_wake_time=0 when flip queue isn't used, to
avoid needleslly increasing pkg_c_latency on lnl/ptl due
to Wa_22020432604. This is a bit racy though...
Use IS_DISPLAY_VER()
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250624170049.27284-6-ville.syrjala@linux.intel.com
Provide the lower level code for PIPEDMC based flip queue.
We'll use the so called semi-full flip queue mode where the
PIPEDMC will start the provided DSB on a scanline a little
ahead of the vblank. We need to program the triggering scanline
early enough so that the DSB has enough time to complete writing
all the double buffered registers before they get latched (at
start of vblank).
The firmware implements several queues:
- 3 "plane queues" which execute a single DSB per entry
- 1 "general queue" which can apparently execute 2 DSBs per entry
- 1 vestigial "fast queue" that replaced the "simple flip queue"
on ADL+, but this isn't supposed to be used due to issues.
But we only need a single plane queue really, and we won't actually
use it as a real queue because we don't allow queueing multiple commits
ahead of time. So the whole thing is perhaps useless. I suppose
there migth be some power saving benefits if we would get the flip
scheduled by userspace early and then could keep some hardware powered
off a bit longer until the DMC kicks off the flipq programming. But that
is pure speculation at this time and needs to be proven.
The code to hook up the flip queue into the actual atomic commit
path will follow later.
TODO: need to think how to do the "wait for DMC firmware load" nicely
need to think about VRR and PSR
etc.
v2: Don't write DMC_FQ_W2_PTS_CFG_SEL on pre-lnl
Don't oops at flipq init if there is no dmc
v3: Adapt to PTL+ flipq changes (different queue entry
layout, different trigger event, need VRR TG)
Use the actual CDCLK frequency
Ask the DSB code how long things are expected to take
v3: Adjust the cdclk rounding (docs are 100% vague, Windows
rounds like this)
Initialize some undocumented magic DMC variables on PTL
v4: Use PIPEDMC_FQ_STATUS for busy check (the busy bit in
PIPEDMC_FQ_CTRL is apparently gone on LNL+)
Based the preempt timeout on the max exec time
Preempt before disabling the flip queue
Order the PIPEDMC_SCANLINECMP* writes a bit more carefully
Fix some typos
v5: Try to deal with some clang-20 div-by-zero false positive (Nathan)
Add some docs (Jani)
Cc: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
epr
Link: https://patchwork.freedesktop.org/patch/msgid/20250624170049.27284-5-ville.syrjala@linux.intel.com
Add the register definitions for a bunch of flip queue related
PIPEDMC registers.
v2: The layout of flip queue entries changed on PTL
Bump the DMC_FQ_W2_PTS_CFG_SEL bitfields sizes (Uma)
Reduce the scanlines to 21 bits for now (Uma)
v3: Also define some undocumented DMC variables we need on PTL
v3: Drop PIPEDMC_FQ_CTRL_BUSY as it seems to no longer exist
on LNL+
Fix up some typos
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250624170049.27284-4-ville.syrjala@linux.intel.com
The current PKG_C_LATENCY stuff looks busted in several ways:
- doesn't account for multiple pipes from different commits
correctly
- WM_LINETIME is in units of 0.125usec, PKG_C_LATENCY wants
units on 1 usec
- weird VRR state stuff being checked
- use of pointless RMW
Fix it all up. Note that it's still a bit unclear how all this
works, especially how the added_wake_time ties into the flipq
triggers in DMC, and how we need to sequence updates to
PKG_C_LATENCY when enabling/disabling pipes/etc. We may also
need to think what to about the WM1+ disabling and the related
PSR chicken bits when we can use PKG_C_LATENCY for early wake...
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250624170049.27284-3-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Commit 77ba0b8562 ("drm/i915/dsi: convert vlv_dsi.[ch] to struct
intel_display") added a to_intel_display(connector) call to
vlv_dphy_param_init() but when vlv_dphy_param_init() gets called
the connector object has not been initialized yet, so this leads
to a NULL pointer deref:
BUG: kernel NULL pointer dereference, address: 000000000000000c
...
Hardware name: ASUSTeK COMPUTER INC. T100TA/T100TA, BIOS T100TA.314 08/13/2015
RIP: 0010:vlv_dsi_init+0x4e6/0x1600 [i915]
...
Call Trace:
<TASK>
? intel_step_name+0x4be8/0x5c30 [i915]
intel_setup_outputs+0x2d6/0xbd0 [i915]
intel_display_driver_probe_nogem+0x13f/0x220 [i915]
i915_driver_probe+0x3d9/0xaf0 [i915]
Use to_intel_display(&intel_dsi->base) instead to fix this.
Fixes: 77ba0b8562 ("drm/i915/dsi: convert vlv_dsi.[ch] to struct intel_display")
Signed-off-by: Hans de Goede <hansg@kernel.org>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://lore.kernel.org/r/20250626143317.101706-1-hansg@kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
When the panic handler is called, configure the psr to send the full
framebuffer to the monitor, otherwise the panic screen is only
partially visible.
Signed-off-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://lore.kernel.org/r/20250624091501.257661-12-jfalempe@redhat.com
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
On Alder Lake and later, it's not possible to disable tiling when DPT
is enabled.
So this commit implements 4-Tiling support, to still be able to draw
the panic screen.
Signed-off-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://lore.kernel.org/r/20250624091501.257661-11-jfalempe@redhat.com
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
On Alder Lake and later, it's not possible to disable tiling when DPT
is enabled.
So this commit implements Y-Tiling support, to still be able to draw
the panic screen.
Signed-off-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://lore.kernel.org/r/20250624091501.257661-10-jfalempe@redhat.com
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
This adds drm_panic support for a wide range of Intel GPU. I've
tested it only on 4 laptops, Haswell (with 128MB of eDRAM),
Comet Lake, Raptor Lake, and Lunar Lake.
For hardware using DPT, it's not possible to disable tiling, as you
will need to reconfigure the way the GPU is accessing the
framebuffer, so this will be handled by the following patches.
Signed-off-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://lore.kernel.org/r/20250624091501.257661-9-jfalempe@redhat.com
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
Implement both functions for i915 and xe, they prepare the work for
drm_panic support.
They both use kmap_try_from_panic(), and map one page at a time, to
write the panic screen on the framebuffer.
Signed-off-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://lore.kernel.org/r/20250624091501.257661-8-jfalempe@redhat.com
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
Encapsulate the struct intel_framebuffer into an xe_framebuffer
or i915_framebuffer, and allow to add specific fields for each
variant for the panic use-case.
This is particularly needed to have a struct xe_res_cursor available
to support drm panic on discrete GPU.
Signed-off-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://lore.kernel.org/r/20250624091501.257661-7-jfalempe@redhat.com
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
If the ttm bo is backed by pages, then it's possible to safely kmap
one page at a time, using kmap_try_from_panic().
Unfortunately there is no way to do the same with ioremap, so it
only supports the kmap case.
This is needed for proper drm_panic support with xe driver.
Signed-off-by: Jocelyn Falempe <jfalempe@redhat.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://lore.kernel.org/r/20250624091501.257661-6-jfalempe@redhat.com
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
drm_panic draws in linear framebuffer, so it's easier to re-use the
current framebuffer, and disable tiling in the panic handler, to show
the panic screen.
This assumes that the alignment restriction is always smaller in
linear than in tiled.
It also assumes that the linear framebuffer size is always smaller
than the tiled.
Signed-off-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://lore.kernel.org/r/20250624091501.257661-5-jfalempe@redhat.com
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
drm_panic draws in linear framebuffer, so it's easier to re-use the
current framebuffer, and disable tiling in the panic handler, to show
the panic screen.
This assumes that the alignment restriction is always smaller in
linear than in tiled.
It also assumes that the linear framebuffer size is always smaller
than the tiled.
Signed-off-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://lore.kernel.org/r/20250624091501.257661-4-jfalempe@redhat.com
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
The vaddr of the fbdev framebuffer is private to the struct
intel_fbdev, so this function is needed to access it for drm_panic.
Also the struct i915_vma is different between i915 and xe, so it
requires a few functions to access fbdev->vma->iomap.
Signed-off-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://lore.kernel.org/r/20250624091501.257661-3-jfalempe@redhat.com
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
This allows driver to set some private data in get_scanout_buffer(),
and re-use them in set_pixel() callback.
Signed-off-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://lore.kernel.org/r/20250624091501.257661-2-jfalempe@redhat.com
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
There was an error pointer vs NULL bug in __igt_breadcrumbs_smoketest().
The __mock_request_alloc() function implements the
smoketest->request_alloc() function pointer. It was supposed to return
error pointers, but it propogates the NULL return from mock_request()
so in the event of a failure, it would lead to a NULL pointer
dereference.
To fix this, change the mock_request() function to return error pointers
and update all the callers to expect that.
Fixes: 52c0fdb25c ("drm/i915: Replace global breadcrumbs with per-context interrupt tracking")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://lore.kernel.org/r/685c1417.050a0220.696f5.5c05@mx.google.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Create a new unordered workqueue to be used by the display code
instead of relying on the i915 one. Then move all the unordered works
used in the display code to use this new queue.
Since this is an unordered workqueue, by definition there can't be any
order dependency with non-display works, so no extra care is needed
in regard to that.
This is part of the effort to isolate the display code from i915.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://lore.kernel.org/r/20250620091632.1256135-1-luciano.coelho@intel.com
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
With all the code touching struct intel_bw_state moved inside
intel_bw.c, we move the struct definition there too, and make the type
opaque. to_intel_bw_state() needs to be turned into a proper
function. All of this nicely reduces includes from intel_bw.h.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://lore.kernel.org/r/743ba67e4e3c5dac4f5e58ab4d2357edea601d09.1750847509.git.jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
