Add pcie0-ep node information and apply pcie0-ep overlay file.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use common imx-pcie0-ep.dtso for imx8mp-evk-pcie-ep and
imx8qxp-mek-pcie-ep. No functional change.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add unified pcie<n> and pcie<n>_ep label for existed chipes to prepare
applied one overay file to enable EP function.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The needed drivers to support PCIe and SATA for i.MX 8QM have been
added.
Configure them for the Apalis iMX8 SoM.
The pciea and pcieb blocks each get a single PCIe lane, pciea is
available on the carrier boards while pcieb is connected to the
on module Wi-Fi/BT module.
The SATA lane is available on the carrier boards.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Using the MDIO pins with Open Drain causes spec violations of the
signals. Revert the changes.
This reverts commit 315d7f301e.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Using the MDIO pins with Open Drain causes spec violations of the
signals. Revert the changes.
This reverts commit 9015397c2f.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable the interrupts and wakeup-source to allow the external RTC to be
used as an alarm.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable the interrupts and wakeup-source to allow the external RTC to be
used as an alarm.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable the interrupts and wakeup-source to allow the external RTC to be
used as an alarm.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Ethernet PHY setup currently assumes that the bootloader will take the
PHY out of reset, but this behavior is not guaranteed across all
bootloaders. Add the reset GPIO to ensure the kernel can properly control
the PHY reset line.
Also configure the PHY IRQ GPIO to enable interrupt-driven link status
reporting, instead of relying on polling.
This ensures more reliable Ethernet initialization and improves PHY event
handling.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Ethernet PHY setup currently assumes that the bootloader will take the
PHY out of reset, but this behavior is not guaranteed across all
bootloaders. Add the reset GPIO to ensure the kernel can properly control
the PHY reset line.
Also configure the PHY IRQ GPIO to enable interrupt-driven link status
reporting, instead of relying on polling.
This ensures more reliable Ethernet initialization and improves PHY event
handling.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The HDMI bridge chip fails to generate an audio source due to the SAI5
master clock (MCLK) direction not being set to output. This prevents proper
clocking of the HDMI audio interface.
Add the `fsl,sai-mclk-direction-output` property to the SAI5 node to ensure
the MCLK is driven by the SoC, resolving the HDMI sound issue.
Fixes: 1d6880ceef ("arm64: dts: imx8mn-beacon: Add HDMI video with sound")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The HDMI bridge chip fails to generate an audio source due to the SAI5
master clock (MCLK) direction not being set to output. This prevents proper
clocking of the HDMI audio interface.
Add the `fsl,sai-mclk-direction-output` property to the SAI5 node to ensure
the MCLK is driven by the SoC, resolving the HDMI sound issue.
Fixes: 8ad7d14d99 ("arm64: dts: imx8mm-beacon: Add HDMI video with sound")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Although not noticeable when used every day, the RTC appears to drift when
left to sit over time. This is due to the capacitive load not being
properly set. Fix RTC drift by correcting the capacitive load setting
from 7000 to 12500, which matches the actual hardware configuration.
Fixes: 25a5ccdce7 ("arm64: dts: freescale: Introduce imx8mp-beacon-kit")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Although not noticeable when used every day, the RTC appears to drift when
left to sit over time. This is due to the capacitive load not being
properly set. Fix RTC drift by correcting the capacitive load setting
from 7000 to 12500, which matches the actual hardware configuration.
Fixes: 36ca3c8ccb ("arm64: dts: imx: Add Beacon i.MX8M Nano development kit")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Although not noticeable when used every day, the RTC appears to drift when
left to sit over time. This is due to the capacitive load not being
properly set. Fix RTC drift by correcting the capacitive load setting
from 7000 to 12500, which matches the actual hardware configuration.
Fixes: 593816fa2f ("arm64: dts: imx: Add Beacon i.MX8m-Mini development kit")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds support for TQMa93xx module attached to MBa91xxCA board.
TQMa93xx is a SOM using i.MX93 SOC. The SOM features PMIC, RAM, e-MMC and
some optional peripherals like SPI-NOR, RTC, EEPROM, gyroscope and
secure element.
TQMa93xxCA can be attached directly while TQMa93xxLA needs an adapter.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for the PCA85073A RTC module connected via I2C0 on
S32G274A-RDB2 and S32G399A-RDB3 boards.
Note that the PCA85073A RTC module is not battery backed.
Signed-off-by: Ciprian Marian Costea <ciprianmarian.costea@oss.nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On this board, USB2.0 is a host-only port, add vbus regulator node
and enable USB2.0 node.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On this board, USB2.0 is a host-only port, add vbus regulator node
and enable USB2.0 node.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add USB2.0 controller and phy nodes.
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com> # TQMa95xxSA
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to the AT24 EEPROM bindings the compatible string should
contain first the actual manufacturer, and second the corresponding
atmel model.
Add the atmel compatible fallback accordingly.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to the AT24 EEPROM bindings the compatible string should
contain first the actual manufacturer, and second the corresponding
atmel model.
Add the atmel compatible fallback accordingly.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The "clock-latency" property is part of the deprecated opp-v1 binding
and is redundant if the opp-v2 table has equal or larger values in any
"clock-latency-ns". The OPP tables have values of 150000, so it can be
removed.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move dsp_vdev* to under existed reserved-memory node to consolidate all
reserved-memory together.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
DSP can be used with various frameworks (e.g audio firmware, rproc).
Currently 'dsp' configuration is intended for audio firmware but it
doesn't work well with board level DTs (e.g imx8mp-evk) because
board level DT enables audio related IPs (e.g SAI) while audio firmware
needs this IPs disabled (because firmware will configure them).
So, configure 'dsp' node to be used with rproc. This way users will be
able to use board DT to use the DSP as long as they don't clash with
Audio IP configurations.
More comples usage of 'dsp' node (e.g by audio firmware) will need to
create a separate dts file (or an overlay).
This change follows the approach taken for other i.MX8 boards
in commit 391a319c81 ("arm64: dts: imx8-ss-audio: configure dsp node
for rproc usage")
Reviewed-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add resets property to dsp node in order to be able to control the dsp
run/stall bit from audio block control.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add linux,pci-domain into pcie-ep node of i.MX8MQ.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Set custom differential output voltage for LVDS, to fulfill requirements
of the connected display. LVDS differential voltage for data-lanes and
clock output has to be between 200 mV and 600 mV.
Driver sets 200 Ohm near-end termination by default.
Signed-off-by: Andrej Picej <andrej.picej@norik.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The "real" linux/types.h UAPI header gracefully degrades to a NOOP when
included from assembly code.
Mirror this behaviour in the tools/ variant.
Test for __ASSEMBLER__ over __ASSEMBLY__ as the former is provided by the
toolchain automatically.
Reported-by: Mark Brown <broonie@kernel.org>
Closes: https://lore.kernel.org/lkml/af553c62-ca2f-4956-932c-dd6e3a126f58@sirena.org.uk/
Fixes: c9fbaa8795 ("selftests: vDSO: parse_vdso: Use UAPI headers instead of libc headers")
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Link: https://patch.msgid.link/20250321-uapi-consistency-v1-1-439070118dc0@linutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Support up to 8192 processors
Add cpuidle governor debug telemetry, disabled by default
Update default output to exclude cpuidle invocation counts
Bug fixes
Signed-off-by: Len Brown <len.brown@intel.com>
Create "pct_idle" counter group, the sofware notion of residency
so it can now be singled out, independent of other counter groups.
Create "cpuidle" group, the cpuidle invocation counts.
Disable "cpuidle", by default.
Create "swidle" = "cpuidle" + "pct_idle".
Undocument "sysfs", the old name for "swidle", but keep it working
for backwards compatibilty.
Create "hwidle", all the HW idle counters
Modify "idle", enabled by default
"idle" = "hwidle" + "pct_idle" (and now excludes "cpuidle")
Signed-off-by: Len Brown <len.brown@intel.com>
... and don't error out so hard on missing module descriptions.
Before commit 6c6c1fc09d ("modpost: require a MODULE_DESCRIPTION()")
we used to warn about missing module descriptions, but only when
building with extra warnigns (ie 'W=1').
After that commit the warning became an unconditional hard error.
And it turns out not all modules have been converted despite the claims
to the contrary. As reported by Damian Tometzki, the slub KUnit test
didn't have a module description, and apparently nobody ever really
noticed.
The reason nobody noticed seems to be that the slub KUnit tests get
disabled by SLUB_TINY, which also ends up disabling a lot of other code,
both in tests and in slub itself. And so anybody doing full build tests
didn't actually see this failre.
So let's disable SLUB_TINY for build-only tests, since it clearly ends
up limiting build coverage. Also turn the missing module descriptions
error back into a warning, but let's keep it around for non-'W=1'
builds.
Reported-by: Damian Tometzki <damian@riscv-rocks.de>
Link: https://lore.kernel.org/all/01070196099fd059-e8463438-7b1b-4ec8-816d-173874be9966-000000@eu-central-1.amazonses.com/
Cc: Masahiro Yamada <masahiroy@kernel.org>
Cc: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Fixes: 6c6c1fc09d ("modpost: require a MODULE_DESCRIPTION()")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Probe cpuidle "sysfs" residency and counts separately,
since soon we will make one disabled on, and the
other disabled off.
Clarify that some BIC (build-in-counters) are actually "groups".
since we're about to re-name some of those groups.
no functional change.
Signed-off-by: Len Brown <len.brown@intel.com>
Do fflush() to discard the buffered data, before each read of the
graphics sysfs knobs.
Fixes: ba99a4fc8c ("tools/power turbostat: Remove unnecessary fflush() call")
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
