Rename PIPECONF to TRANSCONF to make it clear what it actually
applies to.
While the usual convention is to pick the earliers name I think
in this case it's more clear to use the later name. Especially
as even the register offset is in the wrong range (0x70000 vs.
0x60000) and thus makes it look like this is per-pipe.
There is one place in gvt that's doing something with TRANSCONF
while iterating with for_each_pipe(). So that might not be doing
the right thing for TRANSCODER_EDP, dunno. Not knowing what it
does I left it as is to avoid breakage.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230213225258.2127-5-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Name the CPU transcoder timing registers TRANS_FOO rather than
just FOO. This is the modern name, after the pipe/transcoder split
happened. Makes it a bit more obvious whether you pass in a pipe or
a transcoder.
PIPESRC is a bit special as it's a pipe register, even though it
lives in the transcoder registers range (0x60000 instead of 0x70000).
And BCLRPAT I suppose is a transcoder register (since it has something
to do with the timing generator), but it doesn't even exist after gen4
so I left it to use the only name it ever had in bspec.
And while at it let's pass in the correct enum in few more
places why don't we. Although in all those places the distinction
doesn't matter.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230213225258.2127-4-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Use an early return to get rid of the extra indentation level
in intel_ddi_{enable,disable}_transcoder_clock().
Also unify the platform handling in between the two while at
it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230213225258.2127-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
SKL/derivatives have DDI E but no AUX E, so we need to pick
another aux ch as the platform default. DDI E is more or less
the other half of DDI A, so we pick AUX A.
In all other cases we should have a corresponding aux ch for
each DDI.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230216231312.32664-3-ville.syrjala@linux.intel.com
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Restructure intel_bios_port_aux_ch() to resemble the ddc_pin
counterpart, where the intel_bios.c stuff only deals with the
child device definition, and the platform default will come from
elsewhere.
This requires the introduction of AUX_CH_NONE as the value 0
is already taken to mean AUX_CH_A.
v2: Sort includes alphabetically (Ankit)
vCould we ask them to do a BIOS fix for all of them so that
we wouldn't keep getting these bug reports for each model
separately?
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230216231312.32664-1-ville.syrjala@linux.intel.com
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Previous documentation suggested that the PL1 power limit is always enabled
in HW. However we now find this not to be the case on some platforms (such
as ATSM). Therefore enable the PL1 power limit (by setting the enable bit)
when writing the PL1 limit value to HW.
Bspec: 51864
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230216164944.2366150-3-ashutosh.dixit@intel.com
hwm_field_scale_and_write has a single caller hwm_power_write and is
specific to hwm_power_write but makes it appear that it is a general
function which can have multiple callers. Replace the function with
hwm_power_max_write which is specific to hwm_power_write and use that in
future patches where the function needs to be extended.
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230216164944.2366150-2-ashutosh.dixit@intel.com
Switch a lot of the intel_bios_foo() stuff to just accept the
devdata (VBT child device info) directly, instead of taking
detours via vbt.ports[].
Also unify the function naming scheme.
v2: Drop the redundant "encoder" from the dp/hdmi specific functions
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230216000425.32216-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Most of the .fb_create() failure paths are annotated but there
are a few that seem capable of failing silently (well, higher
level code should print something, just not anything actually
useful). Drop a few more hints into the log to aid in debugging.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230215222426.26085-2-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
We are failing to free the already allocated DPT if the final
drm_framebuffer_init() fails. That would require idr_alloc() to
fail, so not very likely, but let's add the cleanup code anyway.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230215222426.26085-1-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Do the ELD hexdumps only up to the last differing byte.
The rest is typically all zeroes anyway so not much point
in dumping it.
Couldn't find anything for memcmp_diff_len() so
rolled my own.
v2: Use semantics and function name suggested by Jani
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230215150129.13288-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
With multi panel machines becoming more prominent it's also
important to know which connector's backlight we're talking
about. Include that information in all the backlight debug/error
messages.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230215140021.2843-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Disabling ILK+ watermarks on failure to read the watermark levels dates
back to 2010 and commit 7f8a85698f ("drm/i915: Add the support of
memory self-refresh on Ironlake"), with no explanations, and it's been
copied and modified from that ever since. Finally drop it.
If the value are actually zero, the ilk_compute_*_wm() functions should
handle it gracefully.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230215141910.433043-5-jani.nikula@intel.com
The file was never really about pm types, and now it's even more
obvious. Move under display as intel_wm_types.h.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230215141910.433043-4-jani.nikula@intel.com
Move sanitize_watermarks() to i9xx_wm.[ch] and rename as
ilk_wm_sanitize(). The slightly unfortunate downside is having to expose
intel_atomic_check() from intel_display.c, but this declutters
intel_display.c nicely.
v2:
- Move to i9xx_wm.[ch] instead of intel_wm.[ch] (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230215141910.433043-1-jani.nikula@intel.com
There was a specific SW workaround requested, which should prevent
some watermark issues happening, which requires copying highest
enabled wm level to those disabled wm levels(bit 31 is of course
still needs to be cleared).
This is related to different subsystems like PSR and others, which
may still consult a low power wm values ocassionally, despite those
are disabled. For that reason we need to keep sane values in
correspondent registers, even when those are disabled.
HSDES: 22016115093
v2: Remove redundant WA for ICL and extend this WA for all platforms
starting from SKL, as it seems that we needed this anyway on
all of those(Ville Syrjälä)
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230213164453.5782-1-stanislav.lisovskiy@intel.com
A new step of 480MHz has been added on SKUs that have a RPL-U
device id to support 120Hz displays more efficiently. Use a
new quirk to identify the machine for which this change needs
to be applied.
v2: (Matt)
- Add missing clock steps
- Correct reference clock typo
v3: - Revert to RPL-U subplatform (Jani)
v4: - Remove Bspec reference from code (Jani)
Bspec: 55409
Signed-off-by: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230130100806.1373883-3-chaitanya.kumar.borah@intel.com
Separate out RPLU device ids and add them to both RPL and
newly created RPL-U subplatforms.
v2: (Matt)
- Sort PCI-IDs numerically
- Name the sub-platform to accurately depict what it is for
- Make RPL-U part of RPL subplatform
v3: revert to RPL-U subplatform (Jani)
v4: (Jani)
- Add RPL-U ids to RPL-P platform
- Remove redundant comment
Signed-off-by: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230130100806.1373883-2-chaitanya.kumar.borah@intel.com
It's confusing to debug backlight issues when one can't
easily even tell what kind of backlight control was
selected. Sprinkle uniform debug messages to all the
backlight setup functions.
Also the one that was already there (ext_pwm) was
using drm_info() for some reason. I don't think that's
warranted so switch it to drm_dbg_kms() as well.
v2: Deal with AUX backlights too (Jani)
Move the VLV/CHV initial pipe debug there too (Jani)
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230215135616.30411-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Get rid of the if ladder in intel_modeset_setup_hw_state() and hide a
number of functions by adding a .get_hw_state() hook to watermark
functions. At least for now, combine the platform specific sanitization
to the hw state readouts on the relevant platforms instead of adding a
separate hook for that.
There's a functional change on PCH split platforms: If i9xx_wm_init()
fails to read plane latency and chooses the nop functions,
ilk_wm_get_hw_state() won't get called for readout. Add the
ilk_init_lp_watermarks() call on that path which now won't be called in
.get_hw_state(), as it looks like the only thing that could make a
difference.
v2:
- Add missing static (kernel test robot)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/6da32831e40606cc8b90491b83196917f2ce36ab.1676317696.git.jani.nikula@intel.com
Add new files intel_wm.[ch] and i9xx_wm.[ch] under display/ to hold
generic and pre-SKL watermark code, respectively. SKL+ watermark code
has already been split out to skl_watermark.[ch].
Use the _wm.[ch] naming for brevity; we may want to rename
skl_watermark.[ch] later accordingly.
Add new intel_wm_init() to call either skl_wm_init() or
i9xx_wm_init(i915) depending on the platform, the latter comprising of
the remains of intel_init_pm().
Sprinkle in some minor checkpatch fixes while moving the code.
v2:
- Rebase
- Fix copyright year
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ddf04a07a37f0368b3fef85d4ebb924082fec6cd.1676317696.git.jani.nikula@intel.com
Detecting in intel_device_info_runtime_init() that the display is fused
off or not present should only zero intel_runtime_info::pipe_mask, while
the other related masks will be accordingly zeroed later in the
function. Remove the redundant zeroing of the related fields on GEN7/8.
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230208114300.3123934-5-imre.deak@intel.com
Determining whether the display engine is present on a platform happens
only in intel_device_info_runtime_init(). Initializing the display power
functionality depends on this condition, so move
intel_power_domains_init() later after the runtime init function has
been called.
The next patch fixing platforms without display, depends on this patch.
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230208114300.3123934-3-imre.deak@intel.com
Since we now populate encoder->devdata for all DP capable
platforms we can consult it directly during the eDP
connector init instead of taking a detour via some global
list/array.
Unfortunately we can't quite get rid of
intel_dp_is_port_edp() since it's still used by the higher
level ilk/vlv/chv output setup code.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230208015508.24824-11-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Instead of consulting vbt.ports[] lets just go through the
whole child device list to check whether a specific port
was declared by the VBT or not.
Note that this doesn't change anything wrt. detecting duplicate
child devices with the same port as vbt.ports[] would also always
contain exactly one of the duplicates.
v2: Include a is_port_valid() check to deal with some broken VBTs
Mention something about duplicate port detection (Jani)
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230214073818.20231-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Currently intel_bios_port_aux_ch() digs out the devdata
(VBT child device info) from the vbt.ports[] array. We
need to get rid of that, so just pass in the correct
encoder->devdata (now that we have it also for g4x+ ports)
directly.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230208015508.24824-9-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Let's make encoder->devdata (the VBT information for the port)
available on g4x+ platforms as well. Much easier when you can
just grab it there instead of trying to find it from some global
list array based on the port.
Note that (unlike DDI platforms) we don't currently require
that each DP/HDMI port is actually declared in VBT. Perhaps
in the future we may want to rethink that, but for now just
stick in a debug+FIXME as a reminder.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230208015508.24824-8-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Display WA #1178 calls us to tweak some magic bits when doing AUX
to an external combo PHY port. Instead of looking to see if the VBT
has declared such a port (which could in theory even alias with a
declared eDP port on the same PHY) just check the real situation
based on the registered encoders.
The only slight chicken vs. egg situation here is during output
probing. But typically we'd register the eDP ports first and so
once we get to probe anything external on the combo PHY we have
already determined if it's eDP or not.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230208015508.24824-7-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
intel_bios_is_port_hpd_inverted() is only used on bxt/glk on
which we always have encoder->devdata available. So consult
that instead of digging around in vbt.ports[].
And rename the function to match the common pattern.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230208015508.24824-6-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
The sole user of intel_bios_is_lane_reversal_needed() has
the devdata already located, so pass it in directly instead
of digging it again from vbt.ports[].
And rename the function to follow the common pattern for
these things.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230208015508.24824-5-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
We always have encoder->devdata available on the platforms
that can have LSPCON. So let's start looking there instead
of digging it out from vbt.ports[].
And let's rename the function to fit the common pattern
for these things.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230208015508.24824-4-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
