mirror of
https://github.com/torvalds/linux.git
synced 2026-10-08 11:36:02 +02:00
2ac174dfcd
1481660 Commits
| Author | SHA1 | Message | Date | |
|---|---|---|---|---|
Taylor Bates
|
2ac174dfcd |
mlxsw: spectrum_ptp: Fix napi_gro_receive() call from GC workqueue context
Currently mlxsw_sp1_ptp_ht_gc_collect() is run from the PTP
garbage-collection workqueue, rather than the NAPI poll context. For any
unmatched PTP entries carrying an SKB, it calls
mlxsw_sp1_ptp_unmatched_finish() -> mlxsw_sp1_ptp_packet_finish(). For
ingress packets, this calls mlxsw_sp_rx_listener_no_mark_func(). The end
of that function is the following:
skb->protocol = eth_type_trans(skb, skb->dev);
napi_gro_receive(mlxsw_skb_cb(skb)->rx_md_info.napi, skb);
The napi pointer is one that was placed in the SKB control block when the
trapped packet was received in the NAPI context. Later, when the GC reaps
the unmatched entry (up to MLXSW_SP1_PTP_HT_GC_TIMEOUT later), the call to
napi_gro_receive() mutates the NAPI instance's GRO list, which is unsafe
if the poll is running concurrently on another CPU.
In mlxsw_sp1_ptp_ht_gc_collect(), local_bh_disable() is called to prevent
softirq processing, but this only applies to the local CPU. Additionally,
its comment is stale. It states that mlxsw_sp1_ptp_unmatched_finish()
invokes netif_receive_skb(). This has not been accurate since the
referenced commit; this patch makes that comment accurate again.
mlxsw_pci_napi_devs_init() calls netif_threaded_enable() on the NAPI RX
net_device without any conditions. The NAPI instance's poll, which may be
running concurrent to the GC, is running as an independently-scheduled
kthread which may be on a different CPU. The call to local_bh_disable()
does not guard against this.
If a tx-timestamp timeout produces an unmatched entry (which can be easily
reproduced by running ptp4l and waiting for a port to reach the
UNCALIBRATED/SLAVE state) while the owning NAPI thread is in the middle of
a poll on another CPU, both sides mutate the GRO list concurrently, as
shown below:
[39.846] port 1 (swp1): MASTER to UNCALIBRATED on RS_SLAVE
list_add corruption. next->prev should be prev (ffff8d620faf4138), but was ffff8d624150f700. (next=ffff8d620faf4138).
kernel BUG at lib/list_debug.c:29!
Oops: invalid opcode: 0000 [#1] SMP PTI
CPU: 1 UID: 0 PID: 539 Comm: napi/mlxsw_rx-0 Not tainted 6.18.48 #1-NixOS PREEMPT(lazy)
Hardware name: Mellanox Technologies Ltd. MSN2410/VMOD0001, BIOS 4.6.5 09/13/2018
RIP: 0010:__list_add_valid_or_report+0x79/0xb0
RSP: 0018:ffffcdf8c0f27c08 EFLAGS: 00010246
RAX: 0000000000000075 RBX: ffff8d624150fd00 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000001 RDI: ffff8d6315d1e540
RBP: ffff8d620faf4070 R08: 0000000000000000 R09: 00000000ffffdfff
R10: ffffffffa5c60fe0 R11: ffffcdf8c0f27ab8 R12: 0000000000000003
R13: 000000000000003d R14: 00000000000001bc R15: 0000000000000001
FS: 0000000000000000(0000) GS:ffff8d636f63f000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000562689a60c24 CR3: 000000015f224004 CR4: 00000000001726f0
Call Trace:
<TASK>
gro_receive_skb+0xee/0x230
mlxsw_sp1_ptp_got_packet+0x61/0x140 [mlxsw_spectrum]
mlxsw_core_skb_receive+0xdf/0x1b0 [mlxsw_core]
mlxsw_pci_napi_poll_cq_rx+0x780/0x9d0 [mlxsw_pci]
__napi_poll+0x31/0x1e0
napi_threaded_poll_loop+0x16b/0x1c0
napi_threaded_poll+0x71/0xa0
kthread+0xfb/0x260
ret_from_fork+0x22d/0x260
ret_from_fork_asm+0x1a/0x30
</TASK>
Kernel panic - not syncing: Fatal exception in interrupt
The machinery that leads to this kernel panic has not been changed between
6.18.48 and mainline.
This patch adds an ingress-delivery helper for the PTP packet_finish()
path that calls netif_receive_skb() instead of napi_gro_receive().
netif_receive_skb(), unlike napi_gro_receive(), can be called from outside
of the NAPI instance's poll context, which can occur at the call site for
this path. RX stats accounting and the skb->dev assignment are still
preserved; the only change is the delivery call itself.
This removes GRO batching for any PTP event traffic received by the mlxsw
trap, but given the relatively low volume of traffic characteristic of the
protocol, and impact limited to only Spectrum-1 ASICs, this is an
acceptable solution.
Fixes:
|
||
|
Zihan Xi
|
efdfb1e27a |
ipv4: fib: bound automatic table ID allocation
fib_empty_table() probes every table ID from 1 until it finds a
free one. IPv4 tables are stored in a 256-bucket hash table, so a
dense set of IDs makes each probe walk a growing hash chain while
RTNL is held.
Automatic table assignment ("ip rule ... table 0") is an IPv4-only
legacy path. Bound the automatically allocated ID to 4096 so the
RTNL hold stays bounded, without changing lookups of explicitly
specified table IDs.
This changes user-visible behavior. A table-0 rule previously
received the lowest free ID in 1..RT_TABLE_MAX (0xFFFFFFFF). After
this patch the search stops at 4096 and the rule add fails with
ENOBUFS if that range is fully occupied. Explicit table IDs above
4096 remain usable.
The automatic path is unused in practice: it is IPv4-only, not
documented by ip-rule, uncovered by kernel selftests, and both
NetworkManager and systemd refuse table 0.
Fixes:
|
||
|
Jakub Kicinski
|
b6dd676d32 |
Merge branch 'net-bcmasp-fix-tx-ring-accounting-bugs'
Danesh Petigara says:
====================
net: bcmasp: fix TX ring accounting bugs
Two fixes for TX descriptor ring handling in the bcmasp driver:
- tx_spb_ring_full() re-initialized next_index from
intf->tx_spb_index on every loop iteration instead of advancing
it, so it only ever checked a single descriptor slot regardless
of cnt. This let bcmasp_xmit() proceed even when the ring didn't
actually have enough free slots for the SKB's fragments.
- bcmasp_xmit() only set txcb->last for the final fragment of an
SKB, leaving stale true values in reused descriptor slots from a
prior transmission. Combined with the ring-full miscount above,
this could cause bcmasp_tx_reclaim() to treat a mid-SKB
descriptor as the last one and free the sk_buff while later
fragments were still in flight.
Patch 1 clears txcb->last unconditionally before it is set, and
patch 2 fixes the ring-full slot check to advance through each
candidate slot.
====================
Link: https://patch.msgid.link/20260831184235.4133351-1-danesh.petigara@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
||
|
Justin Chen
|
0c5cf62e72 |
net: bcmasp: fix tx_spb_ring_full() checking same slot cnt times
The loop initialised next_index from intf->tx_spb_index on every
iteration, so incr_ring() always produced the same result and only
one slot was ever tested. Move the initialisation before the loop
so each iteration advances next_index and the function correctly
checks that cnt consecutive descriptor slots are available before
allowing a new transmission.
Fixes:
|
||
|
Justin Chen
|
18e5e0ec0e |
net: bcmasp: clear txcb->last before writing each descriptor
bcmasp_xmit() only wrote txcb->last = true for the final fragment
of an SKB; non-final fragments left the field untouched. If a
descriptor slot was reused while it still held a stale true from
a previous SKB (possible when tx_spb_ring_full() underreported
fullness), bcmasp_tx_reclaim() would see last == true mid-SKB and
call dev_consume_skb_any() prematurely, freeing the sk_buff while
its remaining fragments were still in flight.
Unconditionally clear txcb->last before the conditional set so every
descriptor slot starts from a known false state regardless of what a
prior transmission left behind.
Fixes:
|
||
|
Linus Torvalds
|
adf50c47a4 |
Including fixes from bluetooth.
Previous releases - regressions:
- page_pool: keep frag_offset aligned for odd-sized requests
- sched: fix u32 duplicate handle when node ID pool is exhausted
- udp: create exceptions before socket matching
- igmp: convert struct ip_sf_list to RCU
- ip6_gre: check tunnel info before xmit in ip6gre_tunnel_xmit
- rds: acquire the fastpath locks in rds_conn_shutdown()
- tipc:
- protect node reset trace dump with node lock
- fix NULL deref in tipc_named_node_up() on empty publication list
- bluetooth:
L2CAP: fix out-of-bounds write in l2cap_ecred_connect
hci_core: fix race condition during device registration
- eth: mlx5e: prevent stale XSK buffer release on refill retries
- eth: bridge: don't truncate the port group walk on teardown
Previous releases - always broken:
- gro: fix nesting of TCP GSO SKBs in skb_gro_receive_list()
- sched: fix skb sizing and action leak on reoffload delete
- tcp: fix use-after-free in do_tcp_getsockopt()
- af_packet: don't cast tpacket_hdr.tp_len to int in tpacket_parse_header().
- sctp: fix soft lockup from unpadded ASCONF-ACK parameter iteration
- iptunnel: fix stale transport header during tunnel decapsulation
- eth: vxlan: fix use-after-free in vxlan_mdb_remote_src_del()
- eth: bonding: fix uninitialized transport header access in alb_determine_nd()
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
-----BEGIN PGP SIGNATURE-----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=0sv8
-----END PGP SIGNATURE-----
Merge tag 'net-7.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from bluetooth.
Previous releases - regressions:
- page_pool: keep frag_offset aligned for odd-sized requests
- sched: fix u32 duplicate handle when node ID pool is exhausted
- udp: create exceptions before socket matching
- igmp: convert struct ip_sf_list to RCU
- ip6_gre: check tunnel info before xmit in ip6gre_tunnel_xmit
- rds: acquire the fastpath locks in rds_conn_shutdown()
- tipc:
- protect node reset trace dump with node lock
- fix NULL deref in tipc_named_node_up() on empty publication
list
- bluetooth:
- L2CAP: fix out-of-bounds write in l2cap_ecred_connect
- hci_core: fix race condition during device registration
- eth:
- mlx5e: prevent stale XSK buffer release on refill retries
- bridge: don't truncate the port group walk on teardown
Previous releases - always broken:
- gro: fix nesting of TCP GSO SKBs in skb_gro_receive_list()
- sched: fix skb sizing and action leak on reoffload delete
- tcp: fix use-after-free in do_tcp_getsockopt()
- af_packet: don't cast tpacket_hdr.tp_len to int in
tpacket_parse_header()
- sctp: fix soft lockup from unpadded ASCONF-ACK parameter iteration
- iptunnel: fix stale transport header during tunnel decapsulation
- eth:
- vxlan: fix use-after-free in vxlan_mdb_remote_src_del()
- bonding: fix uninitialized transport header access in
alb_determine_nd()"
* tag 'net-7.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (83 commits)
net: gro: Fix nesting of TCP GSO SKBs in skb_gro_receive_list()
net: stmmac: reconfigure RX packet parser table in stmmac_hw_setup() after reset
net: airoha: enable RX_DONE interrupt for RX queue 31
net/rds: don't let rds_conn_shutdown() consume a concurrent drop
net/rds: acquire the fastpath locks in rds_conn_shutdown()
net/rds: acquire RDS_IN_XMIT in rds_tcp_reset_callbacks()
net/rds: tcp: don't force RDS_CONN_RESETTING over a concurrent shutdown
net/rds: clear cp_flags bits individually in rds_conn_path_reset()
net/rds: use clear_bit_unlock() in release_refill()
net/rds: use wq_has_sleeper() in release_in_xmit()
net: usb: qmi_wwan: add Compal EXM-G1x support
net: macb: exclude software FCS from TX byte statistics
net: Remove conflicting altnames for dying netns in __dev_change_net_namespace().
net: bridge: mcast: don't truncate the port group walk on teardown
bonding: do not clear curr_active_slave prematurely when releasing all slaves
net: qrtr: Send HELLO message on endpoint register
octeontx2-af: Fix limiting SRIOV VF count logic
bonding: alb: fix uninitialized transport header access in alb_determine_nd()
s390/ctcm: Prevent XID null dereference
net: psp: do not inherit the Rx association on clone
...
|
||
|
Linus Torvalds
|
8ab1afb2eb |
- dm-crypt: fix a race condition that could make errors not being reported
- dm-cache: fix rwsem being locked and unlocked from different processes
- dm-integrity: set the 'stable writes' flag
- dm-integrity: fix a buffer overflow introduced in this merge window
- dm-integrity: fix an infinite loop if tag size is greater than 64
- dm-cache: fix demotion statistics
- dm-integrity: fix NULL pointer dereference in the data-recovery mode
- dm-ebs: remove a bogus restriction on the starting sector offset
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRnH8MwLyZDhyYfesYTAyx9YGnhbQUCapmHXxQcbXBhdG9ja2FA
cmVkaGF0LmNvbQAKCRATAyx9YGnhbXwlAP9TGvtNybtjhdQJmo3t528XRdwYrYuJ
TZTRcQ+KMXEAkgEAxG1l4vvECTwSkUhZXub2own7+IypiY8N5cFOWCkdVwc=
=hVzb
-----END PGP SIGNATURE-----
Merge tag 'for-7.3/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mikulas Patocka:
- fix a dm-crypt race condition that could make errors not being reported
- dm-cache:
- fix rwsem being locked and unlocked from different processes
- fix demotion statistics
- dm-integrity:
- set the 'stable writes' flag
- fix a buffer overflow introduced in this merge window
- fix an infinite loop if tag size is greater than 64
- fix NULL pointer dereference in dm-integrity data-recovery mode
- remove a bogus restriction on the dm-ebs starting sector offset
* tag 'for-7.3/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm-ebs: fix incorrect device offset check in ebs_ctr()
dm-integrity: fix NULL pointer dereference when the 'R' flag is used
dm cache: fix demotion stats in passthrough mode
dm-integrity: fix infinite loop on discard with large tag size
dm-integrity: fix buffer overflow with keyed discard
dm-integrity: require stable writes for internal hash modes
dm cache: fix issue with background work locking
dm-crypt: fix a tiny race condition in crypt_dec_pending
|
||
|
Linus Torvalds
|
97be98b94d |
- Serialize truncate, fallocate, and mmap fault paths with
invalidate_lock, avoiding mmap failures during concurrent size changes
and exposure of uninitialized data during allocation.
- Correct fallocate signal and zeroing error handling.
- Fix FITRIM range alignment to prevent discard requests from extending
into allocated clusters.
- Fix free-cluster accounting when cluster-freeing rollback or bitmap
clearing fails.
- Keep volumes marked dirty when ntfs errors have been recorded.
- Compute bi_sector in 512-byte units, preventing silent corruption on
4Kn devices.
- Validate sectors_per_cluster values and prevent undefined shifts when
parsing MFT and index record sizes.
- Bound $AttrDef traversal to the loaded table size.
- Fix MFT record resizing, memmove overlap, and kmap_local cleanup issues.
- Improve error propagation across attribute, EA, and reparse operations,
including returning -ERANGE for undersized xattr buffers.
- Avoid modifying the HasEA flag when setxattr fails and return
DT_UNKNOWN when directory inode lookup fails.
- Reduce contention in WOF decompression by performing block reads outside
the decompression lock.
-----BEGIN PGP SIGNATURE-----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=gAcy
-----END PGP SIGNATURE-----
Merge tag 'ntfs-for-7.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/linkinjeon/ntfs
Pull ntfs fixes from Namjae Jeon:
- Serialize truncate, fallocate, and mmap fault paths with
invalidate_lock, avoiding mmap failures during concurrent size
changes and exposure of uninitialized data during allocation
- Correct fallocate signal and zeroing error handling
- Fix FITRIM range alignment to prevent discard requests from extending
into allocated clusters
- Fix free-cluster accounting when cluster-freeing rollback or bitmap
clearing fails
- Keep volumes marked dirty when ntfs errors have been recorded
- Compute bi_sector in 512-byte units, preventing silent corruption on
4Kn devices
- Validate sectors_per_cluster values and prevent undefined shifts when
parsing MFT and index record sizes
- Bound $AttrDef traversal to the loaded table size
- Fix MFT record resizing, memmove overlap, and kmap_local cleanup
issues
- Improve error propagation across attribute, EA, and reparse
operations, including returning -ERANGE for undersized xattr buffers
- Avoid modifying the HasEA flag when setxattr fails and return
DT_UNKNOWN when directory inode lookup fails
- Reduce contention in WOF decompression by performing block reads
outside the decompression lock
* tag 'ntfs-for-7.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/linkinjeon/ntfs: (23 commits)
ntfs: take invalidate_lock in ntfs_filemap_page_mkwrite()
ntfs: take invalidate_lock in ntfs_setattr_size()
ntfs: handle signal interruption in fallocate
ntfs: fix FITRIM range alignment
ntfs: read WOF chunks outside the decompression lock
ntfs: leave HasEA flag untouched on setxattr failure
ntfs: fix race between fallocate and mmap reads
ntfs: fix memmove overlap in ntfs_new_attr_flags
ntfs: compute bi_sector in 512-byte units
ntfs: reject invalid sectors_per_cluster in the boot sector
ntfs: bound $AttrDef table walk to the loaded table size
ntfs: fix undefined behavior in mft/index record size calculation
ntfs: treat any nonzero dio zero-range return as an error
ntfs: fix incorrect MFT record pointer passed to ntfs_attr_record_resize
ntfs: do not mark the volume clean in sync_fs when errors were recorded
ntfs: skip free cluster decrement when rollback fails
ntfs: only count successfully cleared runs when freeing clusters
ntfs: fix kmap_local leak in write_mft_record_nolock() error paths
ntfs: return real error from ntfs_non_resident_attr_record_add()
ntfs: preserve error code in ntfs_resident_attr_record_add()
...
|
||
|
HW He
|
66817a9794 |
net: gro: Fix nesting of TCP GSO SKBs in skb_gro_receive_list()
Fraglist GRO and hardware GRO can create an fraglist of
HW-GRO packets. This cannot be segmented back into
the original form on TCP tethering scenario.
Avoid constructing such a GSO packet, by flushing an already
built fraglist GRO packet if a hardware GRO packet arrives.
Scenario (Tethering/Forwarding):
1.Driver submits a single TCP packet, P1. P1 is kept in the
gro_list as the first packet.
2. The driver submits a TCP GSO skb, P2. P2 has already aggregated
multiple TCP packets by HW_GRO, and its non-linear data is stored in
frags[].
3. P1 and P2 match the GRO rules, and since there is no local socket,
they are aggregated by skb_gro_receive_list(). The resulting skb,
P3, has a frag_list entry that still contains frags[]:
P3: [ Linear Data ] -> frag_list -> [ Linear Data ]
[ frag[1] ]
[ frag[2] ]
...
4. Later, tcp4_gso_segment() or tcp6_gso_segment() calls
skb_segment_list() to segment P3. However, skb_segment_list() only
segments the entries in frag_list. It does not segment the frags[]
inside P2, so P3 is not restored to the original packets, which leads
to IP fragmentation or packet drop in the following path.
Check skb_is_gso(skb) and current GRO method, make sure fraglist GRO
applies to consecutive non-GSO skb, others adopt regular GRO path.
Fixes:
|
||
|
Lorenzo Bianconi
|
6b8fed2675 |
net: stmmac: reconfigure RX packet parser table in stmmac_hw_setup() after reset
The core software reset issued in stmmac_init_dma_engine() during
ndo_open() callback clears the MTL RX packet parser registers, but
stmmac_rxp_config() is only invoked from the cls_u32 add/delete paths.
After an ifdown/ifup cycle the hardware therefore runs with the default
all-pass table while priv->tc_entries still reports the filters as
installed. Re-apply the RX packet parser table from priv->tc_entries in
stmmac_hw_setup(), right after the software reset, so the filters are
restored when the interface is brought up again.
Fixes:
|
||
|
Lorenzo Bianconi
|
7db28abbea |
net: airoha: enable RX_DONE interrupt for RX queue 31
RX queue 31 has always been allocated and filled by airoha_qdma_init_rx()
since RX_DONE_INT_MASK spans queues 0-31, but none of the RX_IRQ*
_BANK_PIN_MASK values covered BIT(31). As a consequence the RX_DONE
interrupt for queue 31 was never enabled, airoha_qdma_rx_process() never
ran on that queue and its buffers were never reaped.
Route RX queue 31's RX_DONE interrupt to IRQ bank 1 so that the queue
is drained and its buffers returned to the page pool.
Fixes:
|
||
|
Jakub Kicinski
|
2f38e26a57 |
Merge branch 'net-rds-own-the-fastpath-locks-across-connection-teardown'
Allison Henderson says:
====================
net/rds: own the fastpath locks across connection teardown
This is v5 of the follow-up set to "net/rds: Bug fix ports, part 2"
[1] (v1 at [2], v2 at [3], v3 at [4], v4 at [5]). During review of part 2,
the later half of that series needed more work than a respin, so it was
split off into this set together with the companion fixes identified
along the way. As discussed on the v2 thread, it is targeted at net.
RDS connection teardown quiesces the transmit and receive-refill fast
paths by waiting for the RDS_IN_XMIT/RDS_RECV_REFILL bits to be
sampled clear. Sampling a bit clear is not owning it: the fast path
can re-take its bit right after the wait returns and then run
concurrently with the transport shutdown and the send-state reset.
Oracle UEK closed this by making teardown acquire the bits as locks
("rds: Make sure transmit path and connection tear-down does not run
concurrently"); patches 5 and 6 do the same for the two
rds_send_path_reset() call sites upstream.
Making teardown block on the bits as locks promotes several latent
ordering bugs from rare to load-bearing, so they are fixed first:
Patches 1 and 2 fix the release side of the two bit locks.
release_in_xmit() and release_refill() both clear their bit and then
test for waiters, but the barrier is on the wrong side of the clear
to order the critical section's stores before the release, and the
waiter check does not order against the clear. Once teardown blocks
on these bits as locks (uninterruptible and untimed), a lost wake-up
or a store observed out of order stops mattering only in theory.
Use clear_bit_unlock() and wq_has_sleeper(), the pattern already
half-present in release_in_xmit().
Patch 3: rds_conn_path_reset() wipes the whole cp_flags word with a
plain store. Once teardown owns bits in that word across the reset,
a blanket store would end lock ownership early - and it already
races atomic RMWs on the same word today. Clear the bits the reset
is responsible for individually, as Oracle UEK also does.
Patch 4: rds_tcp_reset_callbacks() stores RDS_CONN_RESETTING
unconditionally, which can overwrite the RDS_CONN_ERROR or
RDS_CONN_DISCONNECTING of a shutdown already in progress on the same
path and send that shutdown through an extra drop cycle. Once the
accept path can park for the duration of a teardown (patch 6) that
window widens, so make the transition conditional first, as Oracle
UEK does.
With those in place, patch 5 converts rds_tcp_reset_callbacks() from
waiting on RDS_IN_XMIT to acquiring it, holding it across the socket
swap and rds_send_path_reset(), and patch 6 has rds_conn_shutdown()
hold both bit locks across the transport shutdown and path reset.
Patch 7 fixes a pre-existing teardown-state hole that this series
makes easier to hit but did not introduce. Since commit
|
||
|
Allison Henderson
|
260c6308fe |
net/rds: don't let rds_conn_shutdown() consume a concurrent drop
rds_conn_shutdown() finishes by moving the path from
RDS_CONN_DISCONNECTING to RDS_CONN_DOWN, and also accepts
RDS_CONN_ERROR as the starting state of that final transition, so that
a FIN processed in softirq context during the teardown does not derail
the shutdown into a noisy error path.
But consuming that RDS_CONN_ERROR also consumes the shutdown pass that
came with it: rds_conn_path_drop() sets RDS_CONN_ERROR and then queues
cp_down_w, and a pass that starts on a path already in RDS_CONN_DOWN
is a no-op. For the FIN case that is harmless - the socket the FIN
arrived on is the very socket the teardown just released. It is not
harmless for a dropper that attached something to the path first.
rds_tcp_accept_one() is such a dropper. Its path claim in
rds_tcp_accept_one_path() transitions RDS_CONN_DOWN ->
RDS_CONN_CONNECTING, and a concurrent drop - a FIN on a previous
socket in softirq context, an administrative reset - can put the path
into RDS_CONN_ERROR between that claim and the state check that
follows, which accepts RDS_CONN_ERROR. The accept then installs the
freshly accepted socket with rds_tcp_set_callbacks() while the queued
teardown - which sampled tc->t_sock before this socket existed - is
still running. rds_connect_path_complete() fails its transition to
RDS_CONN_UP and drops the path again, queueing the pass that should
reap the socket it just installed. If the in-flight shutdown's final
transition consumes that drop's RDS_CONN_ERROR, the queued pass finds
the path in RDS_CONN_DOWN and does nothing. The installed socket is
never torn down: it sits established with its callbacks armed and its
rds_tcp_connection on rds_tcp_tc_list, the peer sees a connection that
nothing ever reads, and the path is wedged in RDS_CONN_DOWN until some
later event drops it again. Reproduced with widened race windows as
an ever-growing receive queue on a socket owned by a path stuck in
RDS_CONN_DOWN, with the peer's send path wedged behind it.
Make the final transition only DISCONNECTING -> DOWN. If it fails
because the path is in RDS_CONN_ERROR, a drop raced the teardown:
cancel the reconnect timer and clear RDS_RECONNECT_PENDING - the one
piece of the skipped tail that must not be left behind - and return,
letting the pass the drop queued finish the job: it tears down
whatever attached to the path in the meantime, completes the
transition to RDS_CONN_DOWN, and re-arms the reconnect from its own
tail.
The timer quiesce in that branch matters because the racing drop does
not always queue that pass: rds_conn_path_drop() returns without
queueing when a destroy is pending - exactly the situation during a
netns teardown or module unload, when a FIN on the dying socket is
processed while rds_conn_path_destroy() flushes cp_down_w. If the
flushed pass is the one that takes this return, no later pass exists,
and rds_conn_path_destroy() would find cp_conn_w still armed
(WARN_ON) and then free a path whose reconnect timer can still fire.
With the cancel in the branch, every exit of a shutdown pass leaves
the timer quiesced no matter which pass completes the transition.
The FIN case keeps making progress, one pass later and still without
noisy logging. Any other state keeps today's rds_conn_path_error()
handling; no current cp_state writer can leave a DISCONNECTING path
in anything but RDS_CONN_ERROR (every other writer is a cmpxchg from
a non-DISCONNECTING state), so that branch is defensive.
On kernels without the preceding patches the same hazard exists with
the sample-based quiesce; the fix applies there equally.
Fixes:
|
||
|
Håkon Bugge
|
813f3582ac |
net/rds: acquire the fastpath locks in rds_conn_shutdown()
rds_conn_shutdown() quiesces the transmit and receive-refill paths by
waiting for RDS_IN_XMIT and RDS_RECV_REFILL to be sampled clear, and
then runs the transport shutdown and rds_conn_path_reset(). Sampling
the bits clear is not the same as owning them: the moment after the
wait_event() returns, rds_send_xmit() can re-acquire RDS_IN_XMIT (or
rds_ib_recv_refill() can re-acquire RDS_RECV_REFILL) and run
concurrently with the teardown.
The sender does recheck the connection state after taking the lock,
but that recheck is a classic store-buffering pattern: teardown writes
the state and reads the bit while the sender writes the bit and reads
the state. acquire_in_xmit() is only an acquire operation, so on
weakly ordered architectures both sides can miss each other's write,
and the transmit path then runs while the transport zeroes its rings
(e.g. rds_ib_ring_init()) and rds_send_path_reset() rewrites the
transmit state under it.
Oracle UEK fixed the same class of crashes - a 14-year tail of
BUG_ON()s in rds_ib_sub_signaled(), unexpected op-codes and NULL
dereferences in rds_ib_send_cqe_handler() during failover testing -
by making the teardown path *acquire* the fastpath bit locks instead
of testing them ("rds: Make sure transmit path and connection
tear-down does not run concurrently"). Ownership of a single word is
decided by RMW atomicity, so no cross-variable ordering is needed.
Do the same here: take both locks before calling the transport
shutdown, hold them across rds_conn_path_reset(), and release them
explicitly with a wake-up afterwards. Both are released with
clear_bit_unlock(), so that the ring re-initialization done by the
transport shutdown and the transmit state rewritten by
rds_send_path_reset() are ordered before either bit is seen clear by
the next acquire_in_xmit() or acquire_refill().
The fastpath users of these bits - rds_send_xmit() and
rds_ib_recv_refill() - are trylock style and back off while teardown
owns the locks, so no new lock dependency is introduced for them.
rds_tcp_reset_callbacks() is different: since the previous patch it
acquires RDS_IN_XMIT as well, and it blocks doing so, so its wait now
spans the teardown instead of at most one send batch. That waiter
runs from rds_tcp_accept_one() on the single-threaded krdsd workqueue
and holds rds_tcp_accept_lock and t_conn_path_lock while it waits, so
a duelling SYN accepted while its path is being torn down parks
accept processing for the duration of the teardown - for TCP bounded
by the (up to 5 s) drain loop in rds_tcp_conn_path_shutdown(). An IB
path's drain in rds_ib_conn_path_shutdown() has no round cap, but no
blocking waiter either: rds_tcp_reset_callbacks() is the only blocking
acquirer of these bits and waits only on its own TCP path, and the
fastpaths are trylock-and-back-off on both transports, so a long IB
drain lengthens only that path's own quiesce. The
window is narrow: the accept-side state check has to pass before the
teardown moves the path to RDS_CONN_DISCONNECTING.
Because krdsd is a single global workqueue, everything else queued
there - accept processing for other connections and network
namespaces, and the flush_workqueue(rds_wq) in rds_tcp_listen_stop()
during namespace teardown - waits behind the parked accept worker for
that time. It cannot deadlock, although the waits do point at each
other: the teardown blocks until the bit's holder releases it, and
the holder may be that krdsd accept worker. The holder finishes
without needing anything the teardown owns: the sync cancels
rds_tcp_reset_callbacks() issues target cp_send_w and cp_recv_w on
the path's ordered cp_wq, whose only execution slot is occupied by
the blocked cp_down_w itself, so they are pending at most and cancel
without flushing - a reliance on cp_wq being ordered that is now
noted next to those cancels (on the allocation-failure fallback where
a path shares rds_wq, the work items simply serialize).
Nor is the blocking wait itself new: rds_tcp_reset_callbacks() has
waited on RDS_IN_XMIT from the krdsd work item since
commit
|
||
|
Allison Henderson
|
02c5f9dc2e |
net/rds: acquire RDS_IN_XMIT in rds_tcp_reset_callbacks()
rds_tcp_reset_callbacks() quiesces the transmit path by setting the
path state to RDS_CONN_RESETTING and then waiting for RDS_IN_XMIT to
be sampled clear before swapping the underlying socket and calling
rds_send_path_reset().
Sampling the bit clear is not the same as owning it: rds_send_xmit()
can re-acquire RDS_IN_XMIT right after the wait_event() returns. Its
state recheck after taking the lock is a store-buffering pattern (the
resetter writes the state and reads the bit, the sender writes the
bit and reads the state) and acquire_in_xmit() is only an acquire
operation, so on weakly ordered architectures both sides can miss
each other's write and the transmit path then runs concurrently with
rds_send_path_reset() rewriting cp_xmit_* state - which is exactly
what the comment above rds_send_path_reset() tells its callers to
prevent.
Take the lock instead, hold it across the socket swap and
rds_send_path_reset(), and release it with a wake-up at the end. The
lock-ordering constraint documented above the wait still holds: the
lock is acquired before lock_sock(), so a sender inside tcp_sendmsg()
can never be waited on while we hold the socket lock.
Two details of the old code go away with the same change:
- t_sock is now read only after the lock is acquired. The old code
cached it before waiting; the teardown in rds_conn_shutdown()
releases that socket and clears t_sock, so a pointer cached before
the wait can be stale by the time the accept path resumes. Reading
it under RDS_IN_XMIT is what makes the exclusion complete once the
teardown owns the same lock, which the next patch arranges; until
then the teardown still only samples the bit, and the two paths
remain as exposed to each other as they are today.
- The old !osock early path called rds_send_path_reset() with no
serialization at all. It now runs under the lock like the normal
path. The conditional RDS_CONN_RESETTING transition of the
previous patch happens before the socket check either way: a path
found without a socket is either still connecting (its reconnect
worker blocked on t_conn_path_lock) and legitimately goes
RESETTING -> UP on the new socket, or it has been torn down
meanwhile and is dropped.
The in-function comment describing the old wait-based quiesce is
rewritten to describe the lock-based one, and the stale block comment
above the function (which still described a return value and an
incomplete list of t_sock writers) is refreshed to name all four
writers - the connect, accept, teardown and swap paths - and what
serializes each of them.
Fixes:
|
||
|
Gerd Rausch
|
e8e60d74fe |
net/rds: tcp: don't force RDS_CONN_RESETTING over a concurrent shutdown
rds_tcp_reset_callbacks() resolves a duelling SYN by storing RDS_CONN_RESETTING into cp_state unconditionally. Nothing serializes that store against the shutdown path: rds_tcp_accept_one() checks for RDS_CONN_CONNECTING or RDS_CONN_ERROR under t_conn_path_lock, but neither rds_conn_path_drop(), which forces RDS_CONN_ERROR, nor rds_conn_shutdown(), which moves the path to RDS_CONN_DISCONNECTING under cp_cm_lock, takes that lock. The store can therefore land on top of a shutdown that is already in progress, or that gets queued right after the accept-side check. When it does, the shutdown worker's final DISCONNECTING -> DOWN transition fails and the path goes through rds_conn_path_error() and a second drop/shutdown cycle instead of a clean reconnect, tearing down the socket the accept path has just installed. Before commit |
||
|
Allison Henderson
|
103c4b13c4 |
net/rds: clear cp_flags bits individually in rds_conn_path_reset()
rds_conn_path_reset() wipes the whole flag word with a plain
cp->cp_flags = 0 store. Every other accessor of that word uses
atomic bitops, and some of them can run concurrently with the reset:
RDS_LL_SEND_FULL is set from rds_send_xmit() and cleared from the
transport completion paths, neither of which holds anything that
excludes the shutdown worker. A plain store racing an atomic
read-modify-write on the same word is a data race, and whichever
side loses has its update silently discarded.
Clear the two bits the reset is actually responsible for instead.
RDS_IN_XMIT and RDS_RECV_REFILL need no store at all here: they
belong to the caller, rds_conn_shutdown(), which waits for both to be
clear before calling the transport shutdown and this reset.
This also gives every bit in cp_flags a single well-defined writer
discipline, which the following patches rely on when they turn
RDS_IN_XMIT and RDS_RECV_REFILL into bit locks held across the
teardown: a blanket store mid-teardown would destroy lock ownership
that an atomic clear preserves.
Oracle UEK carries the same conversion ("net/rds: Preserve essential
connection state flags"), motivated by its asynchronous shutdown
state machine, whose progress and destroy flags must survive the
reset. UEK's variant also clears RDS_IN_XMIT and RDS_RECV_REFILL
because there the reset runs as the final step of a teardown that
owns both bits, making those clears its unlock. Upstream that
release belongs in rds_conn_shutdown(): once a later patch in this
series turns the two bits into locks held across the teardown, ending
ownership needs release semantics and a wake-up that a plain clear
inside the reset would not provide.
Based on Oracle UEK commit "net/rds: Preserve essential connection
state flags" by Gerd Rausch.
Fixes:
|
||
|
Allison Henderson
|
17c4476dbb |
net/rds: use clear_bit_unlock() in release_refill()
release_refill() drops the RDS_RECV_REFILL bit with a plain
clear_bit(). clear_bit() has no ordering semantics, and the
smp_mb__after_atomic() that follows it sits on the wrong side for a
lock release: it orders the clear against the waitqueue_active() load
below it, but does nothing to order the refill critical section's ring
and descriptor stores before the clear itself.
That matters once connection teardown owns RDS_RECV_REFILL as a lock
across the transport shutdown and path reset, rather than sampling it
clear, which "net/rds: acquire the fastpath locks in
rds_conn_shutdown()" later in this series arranges: on a weakly
ordered architecture the teardown can win the bit and start the
shutdown and reset while some of the refill's stores are not yet
visible to it. The same gap existed under the sample-based scheme - a
waiter that saw the bit clear had no guarantee it also observed the
refill's stores - but taking the bit as a lock makes the missing
release pairing load-bearing.
Switch to clear_bit_unlock(), which orders the critical section before
the release, and replace the open-coded barrier-plus-waitqueue_active()
with wq_has_sleeper(), whose internal full barrier keeps the
store-buffering guarantee between clearing the bit and checking for
sleepers. This mirrors what "net/rds: use wq_has_sleeper() in
release_in_xmit()" does for RDS_IN_XMIT.
The fast-path acquire side, acquire_refill(), uses test_and_set_bit(),
a full-barrier RMW that pairs with this release. The teardown at this
point in the series still samples the bit, so on its own this change
is release-side hardening; the shutdown-conversion patch named above
makes the teardown acquire the bit with the same RMW, completing the
pairing at the end of the series.
Fixes:
|
||
|
Allison Henderson
|
6d0c8b7073 |
net/rds: use wq_has_sleeper() in release_in_xmit()
release_in_xmit() clears RDS_IN_XMIT with clear_bit_unlock() and then checks waitqueue_active() to decide whether anyone needs waking. clear_bit_unlock() is only a release operation: it orders the critical section before the bit clear, but does not order the subsequent plain load of the wait queue head after it. The waiter side does the mirror image - it adds itself to the wait queue and then tests the bit. That is the classic store-buffering pattern: the releasing CPU can read the wait queue as empty while the waiting CPU still reads the bit as set, so the sleeper is never woken. The waiters are rds_conn_shutdown() and rds_tcp_reset_callbacks(), both in uninterruptible wait_event() with no timeout. A lost wake-up strands the shutdown worker on its single-threaded workqueue until some other sender releases the bit again - and on a connection that is being torn down precisely because it failed, there may never be another sender. The barrier used to be there: release_in_xmit() did clear_bit() followed by smp_mb__after_atomic() until commit |
||
|
Ian Lin
|
08710f033e |
net: usb: qmi_wwan: add Compal EXM-G1x support
The Compal EXM-G1x is a Qualcomm SDX12-based LTE modem. Add support for its QMI WWAN interface 8 using the DTR quirk. Tested on a Compal EXM-G1x modem. Signed-off-by: Ian Lin <jisayme@gmail.com> Link: https://patch.msgid.link/20260831084124.65074-1-jisayme@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> |
||
|
Nicolai Buchwitz
|
d85f521a9a |
net: macb: exclude software FCS from TX byte statistics
Frames for which macb_pad_and_fcs() supplies the FCS have four FCS
bytes appended, and TX completion then accounts the grown skb->len.
tx_bytes is defined to exclude the FCS, so these frames are reported
four bytes too large.
Track only the number of FCS bytes appended in software, 0 or
ETH_FCS_LEN, and subtract that from skb->len at completion. skb->len
already reflects the padded length by then, so there is nothing else
to store. macb_pad_and_fcs() already returns 0 on every non-error
path. Return the FCS length from there instead, rather than
recomputing the same check in the caller. BQL stays on the padded
skb->len that netdev_tx_sent_queue() saw.
Fixes:
|
||
|
Kuniyuki Iwashima
|
debac3a20d |
net: Remove conflicting altnames for dying netns in __dev_change_net_namespace().
syzbot reported the warning in cfg80211_pernet_exit(). [0] The repro does the following: 1. create two device in root netns and non-root netns 2. assign the same altname for the two devices 3. remove the non-root netns Since commit |
||
|
Jun Yang
|
5a3f7a683a |
net: bridge: mcast: don't truncate the port group walk on teardown
__br_multicast_disable_port_ctx() and br_multicast_del_port() walk
port->mglist with hlist_for_each_entry_safe(). However,
br_multicast_find_del_pg() can also delete other entries from the same
list through br_multicast_fwd_src_remove() or __fwd_del_star_excl().
If such an entry is the iterator's saved next node, hlist_del_init()
clears its ->next and terminates the walk early. The reproducer triggers
this in both teardown walks, leaving port groups in the bridge mdb with
a dangling ->key.port after del_nbp() frees the port:
BUG: KASAN: slab-use-after-free in __mdb_fill_info+0x1191/0x1320
__mdb_fill_info+0x1191/0x1320
br_mdb_dump+0x594/0xe40
rtnl_mdb_dump+0x1cf/0x5d0
Use hlist_del_init_rcu() to unlink the group while preserving ->next.
br_multicast_del_pg() and the teardown walks run under
br->multicast_lock. The GC worker must acquire the same lock before
detaching the group for destruction, so the node remains alive while
the walk uses the preserved pointer.
Preserving ->next means a walk can now reach a group that an earlier
iteration already deleted as a side effect. That group is off mp->ports,
so br_multicast_find_del_pg() would fall through its port scan and hit
the trailing WARN_ON(1). Skip such groups at the top of that helper: a
port group is put on port->mglist when it is created and only unlinked
when it is deleted, so hlist_unhashed() identifies exactly this case.
Fixes:
|
||
|
Eric Dumazet
|
af602c7aa5 |
bonding: do not clear curr_active_slave prematurely when releasing all slaves
When releasing all slaves during bond destruction (all == true),
__bond_release_one() unconditionally clears bond->curr_active_slave to
NULL in every iteration.
If a backup slave is released before the active slave,
bond_alb_deinit_slave() triggers rlb_teach_disabled_mac_on_primary(),
which increments the active slave dev promiscuity counter and sets
bond_info->primary_is_promisc = 1.
Because bond->curr_active_slave was prematurely cleared to NULL when
releasing the backup slave, the subsequent iteration releasing the active
slave evaluates oldcurrent as NULL, so bond_change_active_slave(bond, NULL)
is skipped. Consequently, bond_alb_handle_active_change() is never called
to decrement the promiscuity counter, permanently leaking promiscuous
mode on the physical device after bond teardown.
When oldcurrent == slave, bond_change_active_slave(bond, NULL) already sets
bond->curr_active_slave to NULL. We only need to avoid selecting a new
active slave when all == true. Replace the if (all) branch with
if (!all && oldcurrent == slave).
Fixes:
|
||
|
Linus Torvalds
|
940de590b8 |
hardening fix for v7.3-rc2
- Default randstruct off with rust for better allmodconfig coverage (Mark Brown) -----BEGIN PGP SIGNATURE----- iHUEABYKAB0WIQRSPkdeREjth1dHnSE2KwveOeQkuwUCaphPQAAKCRA2KwveOeQk u+JmAP9tcRZkdQkz5oBGNN58SB1eeJ/AQOuOXvqr+fe9Hw0wnQD+OylI5IR5cN9K 7dCHFDbAd3prFT648fnmMlPhBrTpwAw= =x6kf -----END PGP SIGNATURE----- Merge tag 'hardening-v7.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux Pull hardening fix from Kees Cook: - Default randstruct off with rust for better allmodconfig coverage (Mark Brown) * tag 'hardening-v7.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: hardening: Default randstruct off with rust for better allmodconfig support |
||
|
Genjian Zhang
|
7ac81e2d22 |
dm-ebs: fix incorrect device offset check in ebs_ctr()
<offset> is a backing-device sector offset; ti->len is the virtual
target length. Comparing them rejects valid tables, e.g.:
dmsetup create ebs0 --table "0 1048576 ebs /dev/sda 2097152 1 8"
-> ebs: Invalid device offset sector (-EINVAL)
Drop the check. Bounds against the backing device are already
enforced later by device_area_is_invalid() via ebs_iterate_devices().
Cc: stable@vger.kernel.org
Fixes:
|
||
|
Mikulas Patocka
|
7d4d4f3b66 |
dm-integrity: fix NULL pointer dereference when the 'R' flag is used
If the dm-integrity device has the SB_FLAG_DIRTY_BITMAP flag set and the
user activates the device in the 'R' mode, a crash in dm_integrity_resume
happens because the function attempts to read the journal containing the
bitmap.
This patch makes dm-integrity skip any writes to the device in
dm_integrity_resume if the device is activated in the 'R' mode.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Fixes:
|
||
|
Chris Lew
|
544d85de4d |
net: qrtr: Send HELLO message on endpoint register
HELLO is currently handled entirely by the name server (NS): it is sent once as a broadcast when the NS initializes, and again as a reply whenever the NS receives an inbound HELLO from a remote. Some remote QRTR endpoints (e.g. an external WLAN chipset attached over MHI) operate in a slave role: they only ever send a HELLO in response to one they receive, and never initiate. Since the host cannot tell in advance which remotes behave this way, if the host also only replies, both sides wait on the other to speak first and no HELLO is ever exchanged, stalling further communication. To fix this: - Transfer HELLO handshake ownership to the core layer. A HELLO is now sent once, per endpoint, at registration time. - Schedule a delayed work item on endpoint registration to send a HELLO once the name server is bound. The work reschedules itself with a 100ms backoff if the name server socket is not yet bound or if allocating the control packet fails, so a transient startup condition does not abandon the handshake permanently. - Enforce HELLO-first ordering by dropping non-HELLO packets and returning -EAGAIN until the HELLO is confirmed sent, using bool hello_sent guarded by ep_lock to make the gate check atomic with xmit(). - Skip nodes with nid == QRTR_EP_NID_AUTO in bcast_enqueue(), to avoid broadcasting control packets with QRTR_EP_NID_AUTO as the destination node ID. - Remove say_hello() from the name server's ctrl_cmd_hello() handler and from qrtr_ns_init(); the core layer is now the sole sender of the outbound HELLO. This removes the NS's reply-on-receive behaviour without a replacement. Signed-off-by: Chris Lew <christopher.lew@oss.qualcomm.com> Co-developed-by: Deepak Kumar Singh <deepak.singh@oss.qualcomm.com> Signed-off-by: Deepak Kumar Singh <deepak.singh@oss.qualcomm.com> Co-developed-by: Pranav Mahesh Phansalkar <pranav.phansalkar@oss.qualcomm.com> Signed-off-by: Pranav Mahesh Phansalkar <pranav.phansalkar@oss.qualcomm.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Sunil Goutham
|
f695390ea6 |
octeontx2-af: Fix limiting SRIOV VF count logic
When RVU PF0/AF's VFs are SDP instead of LBK, limiting the VF count
based on the LBK channel count is incorrect.
Apply LBK channel-based VF limits only when the VF device ID matches
the LBK RVU AFVF device.
Fixes:
|
||
|
Eric Dumazet
|
70f3995830 |
bonding: alb: fix uninitialized transport header access in alb_determine_nd()
alb_determine_nd() uses icmp6_hdr(skb) to inspect ICMPv6 headers.
However, in xmit paths (e.g. packets sent via AF_PACKET / raw sockets
or forwarded packets), skb->transport_header is not guaranteed to be
initialized. While pskb_network_may_pull() ensures the packet data is
linear starting from the network header, it does not set or adjust the
transport header offset.
Dereferencing icmp6_hdr(skb) can therefore access out-of-bounds memory.
Fetch the icmp6hdr directly after ipv6hdr following pskb_network_may_pull(),
and reload ipv6hdr in case pskb_may_pull() reallocated skb->head.
Also remove the unused bond argument from alb_determine_nd().
Fixes:
|
||
|
Aswin Karuvally
|
b264d84227 |
s390/ctcm: Prevent XID null dereference
The mpc_validate_xid() function sets grp->saved_xid2->xid2_flag2 to 0x40
to signal XID validation error. If peer XID is NULL or r/w channel
pairing mismatch happens, grp->saved_xid2 is never initialized. An
attempt to set the flag in such case leads to NULL dereference.
Fix this by using the always available priv->xid->xid2_flag2 instead of
grp->saved_xid2->xid2_flag2 for validation errors.
Fixes:
|
||
|
Mark Brown
|
2625480a1b |
hardening: Default randstruct off with rust for better allmodconfig support
Currently randstruct does not support rust so we have Kconfig dependencies which prevent rust being enabled when randstruct is. Unfortunately this prevents rust being enabled in allmodconfig, our standard coverage build. randstruct gets turned on by default, then the dependency on !RANDSTRUCT causes rust to get disabled. Work around this by disabling randstruct by default if we have a usable rust toolchain and rust support for the architecture, circular dependencies prevent us directly depending on !RUST. This means we might end up with a configuration that disables both rust and randstruct but hopefully it's more likely go give the expected result. Signed-off-by: Mark Brown <broonie@kernel.org> Acked-by: Miguel Ojeda <ojeda@kernel.org> Link: https://patch.msgid.link/20260901-rust-reverse-randstruct-dep-v4-1-3bfa19efe1fa@kernel.org Signed-off-by: Kees Cook <kees@kernel.org> |
||
|
Linus Torvalds
|
89a312991d |
SMB client fixes for v7.3-rc2
A batch of bug fixes for the SMB client:
- Fixes for fallocate range operations (insert, collapse, zero, punch
hole): the insert range implementation copied overlapping chunks in
the wrong direction, corrupting file data on every server except
Windows. Several related issues in the same area are also
addressed — stale page cache and FS-Cache readback, an integer
truncation on large files, missing RLIMIT_FSIZE validation and
missing sparse file marking.
- Data corruption fixes in the O_TRUNC open path: one where i_size
was zeroed before the server confirmed the truncate and another
where the lack of locking allowed concurrent buffered writes to be
silently discarded.
- Heap overflow fixes in legacy SMB1 paths: one in extended attribute
writes and one in POSIX ACL handling, both exploitable via
unprivileged setxattr(2).
- Fix for multiuser mount with krb5 failing because the username
option was not propagated to new per-user connections.
- Fix for split debug message in __release_mid() after a printk
conversion.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQTcqRusfSdYROJQwGkpVtNKoQNdYwUCapcv6wAKCRApVtNKoQNd
Y0dgAQDvlnpdCsg1SZZN7T/wSy08fP7GEl2lUoCb8m6LQHlDlwEA/RG+FeY8sRkb
iJexqIGT85a48SHmpSavzBO3qkuqIQo=
=+Qbr
-----END PGP SIGNATURE-----
Merge tag 'cifs-fixes-7.3-rc2' of https://git.manguebit.org/linux
Pull smb client fixes from Paulo Alcantara:
- Fixes for fallocate range operations (insert, collapse, zero, punch
hole)
The insert range implementation copied overlapping chunks in the
wrong direction, corrupting file data on every server except Windows.
Several related issues in the same area are also addressed — stale
page cache and FS-Cache readback, an integer truncation on large
files, missing RLIMIT_FSIZE validation and missing sparse file
marking.
- Data corruption fixes in the O_TRUNC open path: one where i_size was
zeroed before the server confirmed the truncate and another where the
lack of locking allowed concurrent buffered writes to be silently
discarded
- Heap overflow fixes in legacy SMB1 paths: one in extended attribute
writes and one in POSIX ACL handling, both exploitable via
unprivileged setxattr(2)
- Fix for multiuser mount with krb5 failing because the username option
was not propagated to new per-user connections
- Fix for split debug message in __release_mid() after a printk
conversion
* tag 'cifs-fixes-7.3-rc2' of https://git.manguebit.org/linux:
smb: client: reject SetEA requests that do not fit the request buffer
smb: client: fix data corruption with concurrent writes and O_TRUNC
cifs: don't update i_size in cifs_do_truncate without a cached handle
smb: client: fix heap overflow in cifs_do_set_acl()
smb: client: fix multiuser mount with krb5
smb: client: transport: Fix debug printing in __release_mid()
smb/client: invalidate fscache for fallocate range operations
smb/client: fix stale page cache in insert/collapse range
smb/client: fix integer truncation in collapse range
smb/client: fix data corruption in emulated insert range
smb/client: mark file sparse before emulating insert range
smb/client: validate new EOF for zero range
smb/client: validate new EOF for insert range
cifs: add revalidation on FSCTL failure in smb2_duplicate_extents()
|
||
|
Linus Torvalds
|
9a58da8005 |
- Prevent unintended data exposure by clearing pipe compound padding and
the response buffer.
- Initialize missing fields in FS_OBJECT_ID_INFORMATION,
FS_CONTROL_INFORMATION, and FS_POSIX_INFORMATION.
- Propagate DACL parsing and allocation failures so malformed security
descriptors are rejected.
- Rate-limit errors for unmapped SIDs to prevent kernel log flooding.
- Drain multichannel sessions during LOGOFF, wake deferred locks and
cancellable requests, and ensure cancellation callbacks run only once.
- Fix listener kthread reference handling and teardown ordering during
netdevice events.
- Validate normalized-name and IPC share configuration response lengths.
- Update the KSMBD MAINTAINERS entry and add Paulo Alcantara as
an SMBDIRECT co-maintainer.
-----BEGIN PGP SIGNATURE-----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=UL/J
-----END PGP SIGNATURE-----
Merge tag 'ksmbd-for-7.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/linkinjeon/smb
Pull smb server fixes from Namjae Jeon:
- Prevent unintended data exposure by clearing pipe compound padding
and the response buffer
- Initialize missing fields in FS_OBJECT_ID_INFORMATION,
FS_CONTROL_INFORMATION, and FS_POSIX_INFORMATION
- Propagate DACL parsing and allocation failures so malformed security
descriptors are rejected
- Rate-limit errors for unmapped SIDs to prevent kernel log flooding
- Drain multichannel sessions during LOGOFF, wake deferred locks and
cancellable requests, and ensure cancellation callbacks run only once
- Fix listener kthread reference handling and teardown ordering during
netdevice events
- Validate normalized-name and IPC share configuration response lengths
- Update the KSMBD MAINTAINERS entry and add Paulo Alcantara as an
SMBDIRECT co-maintainer
* tag 'ksmbd-for-7.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/linkinjeon/smb:
ksmbd: validate normalized name response length
ksmbd: fix listener task lifetime on netdev events
ksmbd: prevent out-of-bounds reads in share config responses
ksmbd: rate limit unmapped SID errors
ksmbd: propagate DACL parsing errors
ksmbd: zero pipe read compound padding
ksmbd: safely drain sessions during logoff
MAINTAINERS: Update the KSMBD entry
MAINTAINERS: Add Paulo Alcantara as an SMBDIRECT co-maintainer
ksmbd: fill in FileSysIdentifier in FS_POSIX_INFORMATION
ksmbd: initialize FileSystemControlFlags in FS_CONTROL_INFORMATION
ksmbd: zero the FS_OBJECT_ID_INFORMATION buffer before filling it in
|
||
|
Ming-Hung Tsai
|
2ccb8878c1 |
dm cache: fix demotion stats in passthrough mode
The demotion counter is incremented per incoming write bio before the
invalidation begins, causing the demotion count to exceed the actual
number of cached blocks when multiple bios target the same cached
block. Additionally, the counter is incremented unconditionally
regardless of invalidation failure.
Reproduce steps:
1. Create a cache device consisting of 512 cache entries
modprobe brd rd_size=262144
dmsetup create cmeta --table "0 8192 linear /dev/ram0 0"
dmsetup create cdata --table "0 65536 linear /dev/ram0 8192"
dmsetup create corig --table "0 65536 linear /dev/ram0 262144"
dd if=/dev/zero of=/dev/mapper/cmeta bs=4k count=1 oflag=direct
dmsetup create cache --table "0 65536 cache /dev/mapper/cmeta \
/dev/mapper/cdata /dev/mapper/corig 128 2 metadata2 writethrough smq 0"
2. Populate the cache, and record the number of cached blocks
fio --name=populate --filename=/dev/mapper/cache --rw=randwrite --bs=4k \
--direct=1 --ioengine=libaio --iodepth=32 --io_size=2048m
nr_cached=$(dmsetup status cache | awk '{split($7, a, "/"); print a[1]}')
3. Reload the cache into passthrough mode
dmsetup suspend cache
dmsetup reload cache --table "0 65536 cache /dev/mapper/cmeta \
/dev/mapper/cdata /dev/mapper/corig 128 2 metadata2 passthrough smq 0"
dmsetup resume cache
4. Write to the passthrough cache with multiple jobs to trigger
multiple bios hitting the same cached block.
fio --filename=/dev/mapper/cache --name=test --rw=write --bs=4k \
--direct=1 --ioengine=libaio --iodepth=32 --numjobs=4
5. Check if demoted matches cached block count. These numbers should
match but may differ due to overcounting per bio.
nr_demoted=$(dmsetup status cache | awk '{print $12}')
echo "$nr_cached, $nr_demoted"
Fix by moving the demotion counter increment into invalidate_complete(),
gated on the success flag.
Reported-by: Ben Marzinski <bmarzins@redhat.com>
Fixes:
|
||
|
Norbert Szetei
|
1d2929d085 |
net: psp: do not inherit the Rx association on clone
sk->psp_assoc sits past sk_dontcopy_end, so sock_copy() copies it into
every socket accepted from a listener without taking a reference, while
inet_sock_destruct() puts for every inet socket. psp_twsk_init() does
refcount_inc() for the timewait socket, so a child closing through
TIME_WAIT cancels its own put and leaves the association with one
reference and N timewait sockets holding the same pointer. Closing the
listener frees it, and the timewait timers then put freed memory.
Rejecting the association on a listening socket is not sufficient: a socket
can acquire one while established and then be turned back into a listener,
because tcp_disconnect() leaves sk->psp_assoc in place.
BUG: KASAN: slab-use-after-free in psp_twsk_assoc_free+0x6f/0xf0
Write of size 4 at addr ffff888110f9255c by task swapper/7/0
psp_twsk_assoc_free+0x6f/0xf0
inet_twsk_put+0xda/0x1b0
call_timer_fn+0x53/0x2e0
__run_timers+0x764/0xa80
Freed by task 99:
kfree+0x1a7/0x500
process_one_work+0x7ec/0x1100
An association carries a per-connection SPI and key, so a child must not
inherit the parent's. Clear it on clone.
Fixes:
|
||
|
Ben Cressey
|
18d80c77b4 |
dm-integrity: fix infinite loop on discard with large tag size
When integrity_metadata handles a discard, it fills a buffer with DISCARD_FILLER and writes it over the tags, max_blocks blocks at a time. If the kmalloc fails, the buffer is the on-stack array checksums_onstack and max_size is set to HASH_MAX_DIGESTSIZE. So if the tag size is larger than HASH_MAX_DIGESTSIZE, max_blocks is zero, bi_size is never decremented and the loop never terminates. Fix this by using sizeof(checksums_onstack) as max_size. The array has MAX_TAG_SIZE bytes since commit |
||
|
Ben Cressey
|
59e6f919d7 |
dm-integrity: fix buffer overflow with keyed discard
Since commit |
||
|
Chen Cheng
|
b2fd92f016 |
dm-integrity: require stable writes for internal hash modes
dm-integrity direct, bitmap and inline internal-hash modes compute
integrity tags from the pages carried by the write bio. The lower data
write also uses those pages, so the tag and the data write depend on the
same memory contents staying unchanged while writeback is in flight.
Without stable writes, a buffered writer can modify a writeback folio
after dm-integrity has submitted the data bio and before the lower device
has consumed the data. After a crash, this can leave data from the later
contents with a tag calculated from the earlier contents, causing
permanent checksum failures on read.
Set BLK_FEAT_STABLE_WRITES for internal-hash D, B and I modes so
filesystems wait for writeback folios to become stable before modifying
them again. Journal mode is left unchanged because it copies data into
the journal before computing and persisting the tag.
Tested using dm-delay over a virtio-blk test disk, dm-integrity
internal_hash:crc32c and no-journal ext4. The D and B reproducers both
failed with checksum errors before this change and completed with
READ_RC=0 and zero mismatches after it.
Fixes:
|
||
|
Benjamin Marzinski
|
bc9781c024 |
dm cache: fix issue with background work locking
dm cache used a rw_semaphore for background_work_lock. Write locks on
rw_semaphores have strict owner semantics, but there was no guarantee
that the process that locked background_work_lock was the same process
that unlocked it. This can be easily seen using a kernel compiled with
CONFIG_DEBUG_RWSEMS. Given a dm cache device <cache>, run: 'dmsetup
suspend <cache> && dmsetup resume <cache>'. This will trigger a kernel
warning:
DEBUG_RWSEMS_WARN_ON((rwsem_owner(sem) != current) && !rwsem_test_oflags(sem, RWSEM_NONSPINNABLE))
triggered by cache_resume(). To fix this, switch from a rw_semaphore to
a spinlock and a wait queue. dm cache already has a wait queue and
associated counter, migration_wait and nr_allocated_migrations, that was
getting woken up when background work was getting completed, but wasn't
actually used by anything. This is replaced by the background_work queue
and counter.
Fixes:
|
||
|
Ben Cressey
|
148845aa19 |
dm-crypt: fix a tiny race condition in crypt_dec_pending
crypt_dec_pending reads io->error before calling atomic_dec_and_test. Another context, for example crypt_endio called from an interrupt, may set io->error and drop its reference between the read and the decrement. crypt_dec_pending then drops the last reference and completes the bio with the stale status - so a read that failed and was never decrypted, or a write that failed, is reported as successful. The read was placed before the decrement by commit |
||
|
Eric Dumazet
|
bc93419130 |
net: bonding: annotate lockless writes with WRITE_ONCE()
Several fields in bonding are read locklessly using READ_ONCE() (or ACCESS_ONCE() previously) but have corresponding writes that do not use WRITE_ONCE(). Add WRITE_ONCE() annotations to: - bond->send_peer_notif decrements in bond_peer_notify_may_events() and reset in bond_close(). - bond->slave_cnt increments and decrements in bond_enslave() and __bond_release_one(). - bond->recv_probe updates in bond_open(), bond_option_arp_interval_set() and rlb_initialize(). - slaves->count decrement in bond_skip_slave(). Fixes: |
||
|
Kaiwen Shi
|
c037915f80 |
mac802154: fix data race and NULL deref on local->assoc_dev
local->assoc_dev is shared between the association path and the
association-response worker without common synchronization.
mac802154_perform_association() stores the coordinator pointer and waits
for a response. Its timeout and error paths clear the pointer and return
to mac802154_associate(), which may then free the coordinator object.
Meanwhile, mac802154_rx_mac_cmd_worker() may observe the associating bit
and enter mac802154_process_association_resp(), which dereferences
assoc_dev.
The worker's bit test and the handler's pointer dereference are not
atomic with respect to cleanup. Cleanup can clear assoc_dev between them,
causing a NULL dereference, or free the coordinator while the response
handler still uses the pointer.
The recorded result is exposed to the same window. assoc_status and
assoc_addr are written by the handler but read by the association path
while the associating bit is still set, so a second response for the same
request - a malicious one, for instance - can replace them between those
reads and leave the caller with an incoherent status and address pair.
The response handler only needs the coordinator extended address.
Replace assoc_dev with a cached address, removing the pointer lifetime
dependency. Protect the cached address and the associating bit with a
dedicated spinlock. A READ_ONCE()/WRITE_ONCE() pair would not guarantee
an atomic __le64 access on all 32-bit architectures.
wpan_dev->association_lock cannot be reused here: nl802154_associate()
holds it across rdev_associate(), hence for the whole of
mac802154_perform_association() including the wait for the response.
A response handler taking that lock would only get it once the
association has already given up.
Reset the completion, publish the cached address, and set the associating
bit while holding the lock. The response handler takes the lock, rechecks
the bit and the cached address, records the response, clears the bit, and
only then completes the waiter. Thus cleanup cannot pass the handler
between its state check and completion, and the cached 64-bit value
cannot tear.
The handler clears the bit before completing, not the woken waiter:
otherwise complete() is issued under the lock and a second (e.g.
malicious) response can reacquire it before the waiter and replace the
result. So a wait that returns success implies the bit is already clear,
and the success and negative-response paths return directly. The
transmit-error and timeout paths still clear it under assoc_lock, which
serializes any racing response against the cleanup while the call returns
the error it already selected. Both paths snapshot assoc_status and
assoc_addr under the same lock.
Both users run in process context, so a plain spinlock is sufficient.
The lock is not held while waiting for the completion.
Suggested-by: Miquel Raynal <miquel.raynal@bootlin.com>
Suggested-by: Xuanqiang Luo <xuanqiang.luo@linux.dev>
Fixes:
|
||
|
Kuniyuki Iwashima
|
73e594c19b |
af_packet: Don't cast tpacket_hdr.tp_len to int in tpacket_parse_header().
syzbot reported BUG() in sock_sendmsg_nosec(). [0]
The problem is that tpacket_parse_header() casts user-provided
tpacket_hdr.tp_len, which is u32, to int.
If the length is larger than INT_MAX, the following condition
in tpacket_parse_header() passes,
if (unlikely(tp_len > size_max))
and any negative value can be returned to the caller, up to
sock_sendmsg_nosec().
The repro set tpacket_hdr.tp_len to 0xfffffdef, which is cast
to -EIOCBQUEUED (-529), triggering BUG() in sock_sendmsg_nosec().
*(uint64_t*)0x200000000008 = 0xfffffdef;
...
syscall(__NR_write, /*fd=*/r[0], /*buf=*/0x200000000000ul, /*count=*/1ul);
Let's define the local tp_len as u32 in tpacket_parse_header().
[0]:
kernel BUG at net/socket.c:803!
Oops: invalid opcode: 0000 [#1] SMP KASAN PTI
CPU: 0 UID: 0 PID: 5628 Comm: syz-executor176 Not tainted syzkaller #0 PREEMPT(full)
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 07/24/2026
RIP: 0010:sock_sendmsg_nosec+0x145/0x180 net/socket.c:803
Code: 06 67 48 0f b9 3a eb 95 e8 e8 3a 22 f8 48 89 df 4c 89 f6 4c 89 e2 4d 89 fb 2e e8 32 a5 5c 16 e9 51 ff ff ff e8 cc 3a 22 f8 90 <0f> 0b e8 c4 3a 22 f8 48 83 c3 18 48 89 d8 48 c1 e8 03 42 80 3c 28
RSP: 0018:ffffc90003aefb48 EFLAGS: 00010293
RAX: ffffffff89a578d4 RBX: ffff8880764c67c0 RCX: ffff88807fb23e80
RDX: 0000000000000000 RSI: 00000000fffffdef RDI: 00000000fffffdef
RBP: 00000000fffffdef R08: ffffc90003aef747 R09: 1ffff9200075dee8
R10: dffffc0000000000 R11: fffff5200075dee9 R12: 0000000000000001
R13: dffffc0000000000 R14: ffffc90003aefbc0 R15: ffffffff8aac4310
FS: 000055559101b400(0000) GS:ffff888124ce0000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000200000000210 CR3: 0000000073dca000 CR4: 00000000003526f0
Call Trace:
<TASK>
__sock_sendmsg net/socket.c:815 [inline]
sock_write_iter+0x2de/0x3e0 net/socket.c:1266
new_sync_write fs/read_write.c:595 [inline]
vfs_write+0x612/0xba0 fs/read_write.c:687
ksys_write+0x150/0x270 fs/read_write.c:739
do_syscall_x64 arch/x86/entry/syscall_64.c:61 [inline]
do_syscall_64+0x166/0x520 arch/x86/entry/syscall_64.c:84
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7f173130ecb9
Code: c0 79 93 eb d5 48 8d 7c 1d 00 eb 99 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 d8 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007ffd67e44248 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
RAX: ffffffffffffffda RBX: 0000200000000000 RCX: 00007f173130ecb9
RDX: 0000000000000001 RSI: 0000200000000000 RDI: 0000000000000003
RBP: 0000000000000001 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00007ffd67e44388
R13: 0000000000000002 R14: 00002000000000c0 R15: 0000000000000002
</TASK>
Fixes:
|
||
|
Linus Torvalds
|
786262be60 |
- Mark the mpc85xx and ThunderX EDAC drivers as orphaned due to lack of
access to hardware
- Remove the unused fake error injection interface from the EDAC debugfs
code due to potential races between logging a fake and a real hw error
- edac_mc_sysfs: Use sysfs_emit_at() for proper bounds checking
- Remove Mark Gross from maintainer entries and move him to CREDITS
- Load the AMD address translation library only on systems which can
actually make use of it (have ECC memory) instead of on every AMD Zen
system out there
- In edac_altera, detect the SoC variant using the ECC manager's
compatible string instead of the build architecture to select the
correct interrupt layout, and remove leftover architecture-specific
ifdeffery from the double-bit error handling path
- Add a new reviewer for the Xilinx EDAC drivers
- Unify address translation logic in Intel client EDAC drivers igen6 and
ie31200 along with detecting memory controller counts at boot time
instead of relying on hardcoded, platform specific numbers. Also, fix
a bunch of issues in them; work by Qiuxu Zhuo
- Add support for a new Intel processor platform Starfire which is
a derivative of Panther Lake SoCs
- The usual cleanups and fixlets all over
-----BEGIN PGP SIGNATURE-----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=t886
-----END PGP SIGNATURE-----
Merge tag 'edac_updates_for_v7.3_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras
Pull forgotten EDAC updates from Borislav Petkov:
"Somewhat belated (and forgotten :-\) EDAC updates lineup for v7.3:
- Mark the mpc85xx and ThunderX EDAC drivers as orphaned due to lack
of access to hardware
- Remove the unused fake error injection interface from the EDAC
debugfs code due to potential races between logging a fake and a
real hw error
- edac_mc_sysfs: Use sysfs_emit_at() for proper bounds checking
- Remove Mark Gross from maintainer entries and move him to CREDITS
- Load the AMD address translation library only on systems which can
actually make use of it (have ECC memory) instead of on every AMD
Zen system out there
- In edac_altera, detect the SoC variant using the ECC manager's
compatible string instead of the build architecture to select the
correct interrupt layout, and remove leftover architecture-specific
ifdeffery from the double-bit error handling path
- Add a new reviewer for the Xilinx EDAC drivers
- Unify address translation logic in Intel client EDAC drivers igen6
and ie31200 along with detecting memory controller counts at boot
time instead of relying on hardcoded, platform specific numbers.
Also, fix a bunch of issues in them; work by Qiuxu Zhuo
- Add support for a new Intel processor platform Starfire which is a
derivative of Panther Lake SoCs
- The usual cleanups and fixlets all over"
* tag 'edac_updates_for_v7.3_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras: (24 commits)
EDAC/thunderx: Orphan it
EDAC/device_sysfs: Cleanup around edac_device_ctl_poll_msec_store()
EDAC/device_sysfs: Use kstrtouint() for poll_msec to prevent truncation
EDAC/igen6: Add Intel Starfire SoCs support
EDAC/igen6: Refactor address translation logic
EDAC/igen6: Remove redundant resource configuration tables
EDAC/igen6: Detect present memory controllers at runtime
EDAC/igen6: Simplify compute die ID comments
EDAC/igen6: Remove unnecessary XOR on the zero-valued interleave bit
EDAC/igen6: Fix Raptor Lake-P logged error address
EDAC/igen6: Fix channel address decode for non-hash mode
EDAC/igen6: Fix channel selection hash
EDAC/igen6: Fix interleave boundary condition
EDAC/ie31200: Decouple DIMM width decoding from enum order
RAS/AMD/ATL: Remove conditional return with no effect
EDAC: Remove redundant dev_err()
MAINTAINERS: Add Radhey Shyam Pandey as Xilinx EDAC reviewer
EDAC/altera: Remove remaining CONFIG_64BIT ifdefs in the DB-error path
EDAC/altera: Use ECC manager compatible to select A10/S10 IRQ layout
RAS/AMD/ATL, EDAC/amd64: Only load ATL when needed
...
|
||
|
Koichiro Den
|
545b63503c |
net: ntb_netdev: Fix statistics races
ntb_netdev updates shared net_device stats from per-QP RX and TX
callbacks. Once multiple queues are enabled, concurrent updates can be
lost.
Use per-CPU tstats for packet and byte counters and DEV_STATS_INC() for
less frequent drop and error counters. Callbacks can run synchronously
in the xmit path or asynchronously from a tasklet or the memcpy kthread.
Pin TX updates against migration in the kthread path. Use the IRQ-safe
u64_stats helpers because netpoll can invoke the synchronous path with
IRQs disabled.
Let the core manage tstats while keeping transport teardown after
unregister_netdev(), outside RTNL. RCU lets unregister wait for TX
completions already updating stats, while later completions only consume
the skb and skip accounting and queue wake.
Fixes:
|
||
|
Eric Dumazet
|
975b5b067f |
ipv6: sr: restore network header before routing and forwarding
ipv6_srh_rcv() runs with skb->data at the Segment Routing Header (SRH)
while skb_network_header() points at the IPv6 header.
When segments_left > 0, ipv6_srh_rcv() previously restored the skb->data
position by pushing sizeof(struct ipv6hdr), assuming the SRH immediately
followed the fixed IPv6 header. If another extension header (such as a
Hop-by-Hop options header) precedes the SRH, skb_network_offset()
remained negative.
This led to two problems:
1. During ip6_route_input(), fib6_rules_early_flow_dissect() invokes
__skb_flow_dissect() which passes the negative skb_network_offset()
to flow dissection, breaking BPF and C flow dissector logic.
2. If forwarded via ip6_forward() or redirected via act_mirred, downstream
handlers (like sch_fragment() or neighbour output) pass the negative
offset as an unsigned length, triggering OOB memcpy or buffer overflows.
Fix this by pushing -skb_network_offset(skb) before routing, ensuring
skb_network_offset(skb) is 0 for route lookup / flow dissection as well as
downstream forwarding. On the loopback path, pull skb_transport_offset(skb)
to restore skb->data to the SRH before looping back.
Fixes:
|
||
|
David Laight
|
81c600c263 |
tipc: Dont send random pad bytes in RESET/ACTIVATE messages
The interface name is passed in a fixed length (TIPC_MAX_IF_NAME) buffer.
Replace the strcpy(data, l->if_name) with memcpy() so that the
pad bytes are actually written (l->if_name[] is zero padded)
rather than sending random bytes from the skb to the remote system.
Replace two other strcpy() with strscpy().
Fixes:
|
||
|
Tung Nguyen
|
b3b76e9f4f |
tipc: fix NULL deref in tipc_named_node_up() on empty publication list
User-space applications can bind a large number of service addresses to
one or more sockets. Each binding of a local-scope service address inserts
one entry (publication) into the TIPC name table. If the number of these
publications exceeds TIPC_MAX_PUBL (65535), protocol service types
(such as node state and link state) are no longer inserted into the name
table. This causes two issues:
1. User-space applications subscribing to node or link up/down events
stop receiving notifications.
2. A NULL pointer dereference can occur:
BUG: kernel NULL pointer dereference, address: 00000000000000d0
...
CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted 7.2.0-rc4-default+ #5 PREEMPT(full)
...
RIP: 0010:tipc_named_node_up (./include/linux/skbuff.h:2251 net/tipc/name_distr.c:195 net/tipc/name_distr.c:221)
...
Call Trace:
<IRQ>
tipc_node_write_unlock (net/tipc/node.c:428)
tipc_rcv (net/tipc/node.c:934 net/tipc/node.c:2189)
tipc_udp_recv (net/tipc/udp_media.c:389)
Thread 1 (tipc_net_finalize) | Thread 2 (named_distribute)
-----------------------------|-----------------------------
| ...
| list_for_each_entry(publ, pls, binding_node) {
| ...
| __skb_queue_tail(list, skb);
| ...
| }
| ...
| hdr = buf_msg(skb_peek_tail(list));
... |
tipc_nametbl_publish(); |
If 'tipc_nametbl_publish()' (Thread 1) fails because the number of
local publications reaches TIPC_MAX_PUBL, list (Thread 2) will be empty. As a
result, NULL is passed to 'buf_msg()', leading to a NULL pointer dereference.
Fix these issues by allowing protocol service types (node state, link state,
and topology server) to be inserted into the name table unconditionally.
This ensures that users subscribing to these types always receive
notifications. In addition, the maximum number of local user publications is
reduced to (TIPC_MAX_PUBL - 1). This ensures that the maximum bulk size
calculated in tipc_link_set_queue_limits() remains valid.
Fixes:
|
||
|
Jakub Kicinski
|
f88bbbbe96 |
Merge branch 'mitigate-a-side-channel-in-routing-exception-caches'
Ido Schimmel says: ==================== Mitigate a side channel in routing exception caches When an ICMP error that quotes a UDP packet is locally delivered, the kernel only creates a routing exception if the quoted packet matches a socket. This allows an off-path attacker to conduct a side-channel attack on the routing exception caches in order to discover the ephemeral ports used by connected UDP sockets. Previous mitigations tried to make it harder for attackers to find hash collisions in these caches and make the eviction of exceptions less predictable. Amit Klein and Noam Caspi demonstrated that both of these mitigations can be bypassed. This patchset tries to mitigate such attacks by always creating an exception, even before trying to find a matching socket. The exception is created by the same helpers that are used when the quoted packet did not originate from a socket, so that guesses (right or wrong) from an off-path attacker always result in an exception being created or updated in the cache that the attacker can observe. Note that this mitigation does not make it easier for attackers to fill these caches, since they can already create exceptions with little to no validation. For example, by sending an ICMP error that quotes an ICMP Echo Reply or one that quotes a UDP source port that matches a wildcard socket. In the good case (matched socket) this comes at the cost of an extra route lookup, as the exception is created before the one performed by the socket path. When the two lookups resolve to different nexthops, an exception is created in the cache of each. Patch #1 fixes a pre-existing bug in the handling of ICMPv6 Redirect Message packets. Discovered while writing the selftest. Patch #2 creates an exception from the IPv4 UDP code even before socket matching. Other socket types do not need this: raw sockets have no ports, and for TCP the ICMP error is discarded unless the quoted sequence number is in window. Patch #3 does the same for IPv6. Patch #4 adds a selftest. v1: https://lore.kernel.org/netdev/20260826143735.1819315-1-idosch@nvidia.com/ ==================== Link: https://patch.msgid.link/20260828192344.2596928-1-idosch@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> |