In some cases, there is a small-time gap in which CMD_RING_BUSY can be
cleared by controller but adding command completion event to event ring
will be delayed. As the result driver will return error code.
This behavior has been detected on usbtest driver (test 9) with
configuration including ep1in/ep1out bulk and ep2in/ep2out isoc
endpoint.
Probably this gap occurred because controller was busy with adding some
other events to event ring.
The CMD_RING_BUSY is cleared to '0' when the Command Descriptor has been
executed and not when command completion event has been added to event
ring.
To fix this issue for this test the small delay is sufficient less than
10us) but to make sure the problem doesn't happen again in the future
the patch introduces 10 retries to check with delay about 20us before
returning error code.
Fixes: 3d82904559 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/PH7PR07MB9538AA45362ACCF1B94EE9B7DD96A@PH7PR07MB9538.namprd07.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb core avoids sending a Set-Interface altsetting 0 request after device
reset, and instead relies on calling usb_disable_interface() and
usb_enable_interface() to flush and reset host-side of those endpoints.
xHCI hosts allocate and set up endpoint ring buffers and host_ep->hcpriv
during usb_hcd_alloc_bandwidth() callback, which in this case is called
before flushing the endpoint in usb_disable_interface().
Call usb_disable_interface() before usb_hcd_alloc_bandwidth() to ensure
URBs are flushed before new ring buffers for the endpoints are allocated.
Otherwise host driver will attempt to find and remove old stale URBs
from a freshly allocated new ringbuffer.
Cc: stable <stable@kernel.org>
Fixes: 4fe0387afa ("USB: don't send Set-Interface after reset")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250514132520.225345-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Qualcomm DWC3 glue driver duplicates the logic of the bulk clock
API to acquire, prepare, and unprepare the controller's clocks. It also
manages the life cycle of these handled explicitly.
Transition to the bulk clock API and manage the resources using devres,
to clean up the code. The resource acquisition is moved above the
initial reset pulse, to handle resource issues before the state is
touched - other than this, this no functional change.
Signed-off-by: Bjorn Andersson <bjorn.andersson@oss.qualcomm.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250508-dwc3-clk-bulk-v2-1-bad3427e88d4@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Avoid unlocking serial_port_lock twice in gserial_suspend(), this can
occur if gserial_wakeup_host() fails. And since wakeup is performed
outside spinlock, check if the port is valid before proceeding again.
Fixes: 3baea29dc0 ("usb: gadget: u_serial: Implement remote wakeup capability")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/all/aBHatifO5bjR1yPt@stanley.mountain/
Signed-off-by: Prashanth K <prashanth.k@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250506104912.3750934-1-prashanth.k@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This device exhibits I/O errors during file transfers due to unstable
link power management (LPM) behavior. The kernel logs show repeated
warm resets and eventual disconnection when LPM is enabled:
[ 3467.810740] hub 2-0:1.0: state 7 ports 6 chg 0000 evt 0020
[ 3467.810740] usb usb2-port5: do warm reset
[ 3467.866444] usb usb2-port5: not warm reset yet, waiting 50ms
[ 3467.907407] sd 0:0:0:0: [sda] tag#12 sense submit err -19
[ 3467.994423] usb usb2-port5: status 02c0, change 0001, 10.0 Gb/s
[ 3467.994453] usb 2-5: USB disconnect, device number 4
The error -19 (ENODEV) occurs when the device disappears during write
operations. Adding USB_QUIRK_NO_LPM disables link power management
for this specific device, resolving the stability issues.
Signed-off-by: Jiayi Li <lijiayi@kylinos.cn>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20250508055947.764538-1-lijiayi@kylinos.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Initialize negotiated_rev and negotiated_rev_prime based on the port's
configured PD revision (rev_major) rather than always defaulting to
PD_MAX_REV. This ensures ports start PD communication using their
appropriate revision level.
This allows proper communication with devices that require specific
PD revision levels, especially for the hardware designed for PD 1.0
or 2.0 specifications.
Signed-off-by: Cosmo Chou <chou.cosmo@gmail.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20250513130834.1612602-1-chou.cosmo@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A state check was previously added to tcpm_queue_vdm_unlocked to
prevent a deadlock where the DisplayPort Alt Mode driver would be
executing work and attempting to grab the tcpm_lock while the TCPM
was holding the lock and attempting to unregister the altmode, blocking
on the altmode driver's cancel_work_sync call.
Because the state check isn't protected, there is a small window
where the Alt Mode driver could determine that the TCPM is
in a ready state and attempt to grab the lock while the
TCPM grabs the lock and changes the TCPM state to one that
causes the deadlock. The callstack is provided below:
[110121.667392][ C7] Call trace:
[110121.667396][ C7] __switch_to+0x174/0x338
[110121.667406][ C7] __schedule+0x608/0x9f0
[110121.667414][ C7] schedule+0x7c/0xe8
[110121.667423][ C7] kernfs_drain+0xb0/0x114
[110121.667431][ C7] __kernfs_remove+0x16c/0x20c
[110121.667436][ C7] kernfs_remove_by_name_ns+0x74/0xe8
[110121.667442][ C7] sysfs_remove_group+0x84/0xe8
[110121.667450][ C7] sysfs_remove_groups+0x34/0x58
[110121.667458][ C7] device_remove_groups+0x10/0x20
[110121.667464][ C7] device_release_driver_internal+0x164/0x2e4
[110121.667475][ C7] device_release_driver+0x18/0x28
[110121.667484][ C7] bus_remove_device+0xec/0x118
[110121.667491][ C7] device_del+0x1e8/0x4ac
[110121.667498][ C7] device_unregister+0x18/0x38
[110121.667504][ C7] typec_unregister_altmode+0x30/0x44
[110121.667515][ C7] tcpm_reset_port+0xac/0x370
[110121.667523][ C7] tcpm_snk_detach+0x84/0xb8
[110121.667529][ C7] run_state_machine+0x4c0/0x1b68
[110121.667536][ C7] tcpm_state_machine_work+0x94/0xe4
[110121.667544][ C7] kthread_worker_fn+0x10c/0x244
[110121.667552][ C7] kthread+0x104/0x1d4
[110121.667557][ C7] ret_from_fork+0x10/0x20
[110121.667689][ C7] Workqueue: events dp_altmode_work
[110121.667697][ C7] Call trace:
[110121.667701][ C7] __switch_to+0x174/0x338
[110121.667710][ C7] __schedule+0x608/0x9f0
[110121.667717][ C7] schedule+0x7c/0xe8
[110121.667725][ C7] schedule_preempt_disabled+0x24/0x40
[110121.667733][ C7] __mutex_lock+0x408/0xdac
[110121.667741][ C7] __mutex_lock_slowpath+0x14/0x24
[110121.667748][ C7] mutex_lock+0x40/0xec
[110121.667757][ C7] tcpm_altmode_enter+0x78/0xb4
[110121.667764][ C7] typec_altmode_enter+0xdc/0x10c
[110121.667769][ C7] dp_altmode_work+0x68/0x164
[110121.667775][ C7] process_one_work+0x1e4/0x43c
[110121.667783][ C7] worker_thread+0x25c/0x430
[110121.667789][ C7] kthread+0x104/0x1d4
[110121.667794][ C7] ret_from_fork+0x10/0x20
Change tcpm_queue_vdm_unlocked to queue for tcpm_queue_vdm_work,
which can perform the state check while holding the TCPM lock
while the Alt Mode lock is no longer held. This requires a new
struct to hold the vdm data, altmode_vdm_event.
Fixes: cdc9946ea6 ("usb: typec: tcpm: enforce ready state when queueing alt mode vdm")
Cc: stable <stable@kernel.org>
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20250506232853.1968304-2-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Register read of TCPC_RX_BYTE_CNT returns the total size consisting of:
PD message (pending read) size + 1 Byte for Frame Type (SOP*)
This is validated against the max PD message (`struct pd_message`) size
without accounting for the extra byte for the frame type. Note that the
struct pd_message does not contain a field for the frame_type. This
results in false negatives when the "PD message (pending read)" is equal
to the max PD message size.
Fixes: 6f413b559f ("usb: typec: tcpci_maxim: Chip level TCPC driver")
Signed-off-by: Amit Sunil Dhamne <amitsd@google.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Kyle Tso <kyletso@google.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/stable/20250502-b4-new-fix-pd-rx-count-v1-1-e5711ed09b3d%40google.com
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250502-b4-new-fix-pd-rx-count-v1-1-e5711ed09b3d@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix kernel-doc warning by documenting the @desc parameter:
drivers/usb/host/xhci.c:1369: warning: Function parameter or struct member 'desc' not described in 'xhci_get_endpoint_index'
Add detailed description of the @desc parameter and clarify the indexing
logic for control endpoints vs other types. This brings the documentation
in line with kernel-doc requirements while maintaining technical accuracy.
Signed-off-by: Hans Zhang <18255117159@163.com>
Link: https://lore.kernel.org/r/20250506033101.206180-1-18255117159@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Interrupt Register Set contains Interrupt Moderation register (IMOD).
The IMOD register contains the following fields:
- Bits 15:0: Interrupt Moderation Interval (IMODI)
- Bits 31:16: Interrupt Moderation Counter (IMODC)
In the xHCI driver, the pointer currently named 'irq_control' refers to the
IMOD register. However, the name 'irq_control' does not accurately describe
the register or its contents, and the xHCI specification does not use the
term "irq control" or "interrupt control" for this register. To improve
clarity and better align with the xHCI specification, the pointer is
renamed to 'imod'.
Additionally, the IMOD register fields IMODI & IMODC have their own masks,
which are also renamed for consistency:
* 'ER_IRQ_INTERVAL_MASK' -> 'IMODI_MASK'
* 'ER_IRQ_COUNTER_MASK' -> 'IMODC_MASK'
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250515135621.335595-23-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Interrupt Register Set contains Interrupt Management register (IMAN).
The IMAN register contains the following fields:
- Bit 0: Interrupt Pending (IP)
- Bit 1: Interrupt Enable (IE)
- Bits 31:2: RsvdP (Reserved and Preserved)
Tn the xhci driver, the pointer currently named 'irq_pending' refers to the
IMAN register. However, the name "irq_pending" only describes one of the
fields within the IMAN register, rather than the entire register itself.
To improve clarity and better align with the xHCI specification,
the pointer is renamed to 'iman'.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250515135621.335595-22-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patch does not contain any functional changes.
Add missing macro descriptions with specific bit definitions for each data
field and reordered them accordingly.
Remove "HW use only" from Interrupt Moderation Counter. xHCI Specification
1.2, section 5.5.2.2, states "This counter may be directly written by
software at any time to alter the interrupt rate."
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250515135621.335595-21-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Event Ring Segment Table Base Address Register contain two fields:
- Bits 5:0: RsvdP (Reserved and Preserved)
- Bits 63:6: Event Ring Segment Table Base Address
Currently, an inverted RsvdP mask (ERST_BASE_RSVDP) is used to extract
bits 63:6. Replaces the inverted mask with a non-inverted mask,
'ERST_BASE_ADDRESS_MASK', which makes the code easier to read.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250515135621.335595-20-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Event Ring Segment Table Size Register contain two fields:
- Bits 15:0: Event Ring Segment Table Size
- Bits 31:16: RsvdZ (Reserved and Zero)
The current mask 'ERST_SIZE_MASK' refers to the RsvdZ bits (31:16).
Change the mask to refer to bits 15:0, which are the Event Ring Segment
Table Size bits.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250515135621.335595-19-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xHCI specification 1.2, section 5.5.2.1.
Interrupt Pending bit is RW1C (Write-1-to-clear), which means that
writing '0' to is has no effect and is removed.
The Interrupt Pending (IP) bit is cleared at the start of interrupt
handling; xhci_clear_interrupt_pending(). This could theoretically
cause a new interrupt to be issued before the xhci driver reaches
the interrupter disable functions.
To address this, the IP bit is read after Interrupt Enable is
disabled, and a debug message is issued if the IP bit is still set.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250515135621.335595-18-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add read call to guarantee that the write to the IMAN register has
been flushed.
xHCI specification 1.2, section 5.5.2.1, Note:
"Most systems have write buffers that minimize overhead, but this may
require a read operation to guarantee that the write has been flushed
from the posted buffer."
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250515135621.335595-17-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Interrupt Management register (IMAN), contains three fields:
- Bit 0: Interrupt Pending (IP)
- Bit 1: Interrupt Enable (IE)
- Bits 31:2: RsvdP (Reserved and Preserved)
Currently, there are multiple macros for both the IP and IE fields.
Consolidates them into single mask macros for better clarity and
maintainability.
Comment "THIS IS BUGGY - FIXME - IP IS WRITE 1 TO CLEAR" refers to the
fact that both macros 'ER_IRQ_ENABLE' and 'ER_IRQ_DISABLE' clear the IP bit
by writing '0' before modifying the IE bit. However, the IP bit is actually
cleared by writing '1'. To prevent any regression, this behavior has not
been altered. Instead, when the IE bit is modified, the IP macro is used
explicitly to highlight this "quirk".
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250515135621.335595-16-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function configures the Interrupt Moderation Interval (IMODI) via bits
15:0 in the Interrupt Moderation Register. The IMODI value is specified in
increments of 250 nanoseconds. For instance, an IMODI register value of 16
corresponds to 4000 nanoseconds, resulting in an interrupt every ~1ms.
Currently, the function fails when a requested IMODI value is too large,
only logging a warning message for secondary interrupters. Prevent this by
automatically adjusting the IMODI value to the nearest supported value.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250515135621.335595-15-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cleanup indentation, spacing and comment formats.
Remove the "// " prefix from trace messages, as it is unnecessary and
distracting.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250515135621.335595-14-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the primary interrupter (0) initialization from xhci_mem_init() to
xhci_init(). This change requires us to save the allocated interrupter
somewhere before initialization. Therefore, store it in the 'interrupters'
array and rework xhci_add_interrupter() to retrieve the interrupter from
the array.
This is part of the ongoing effort to separate allocation and
initialization.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250515135621.335595-12-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove redundant error handling from xhci_add_interrupter() instead of
trying to accommodate them in future changes.
======== Reasoning for the removal ========
Function xhci_add_interrupter() is invoked in two scenarios:
Primary Interrupter Setup (ID 0):
The maximum number of interrupters is always greater than zero, and the
primary interrupter is always allocated as part of the driver's
initialization process. In case of failure, the xHCI driver errors and
exits.
Secondary Interrupter Creation (ID >= 1):
The interrupter is pre-allocated, and an empty slot is identified before
invoking xhci_add_interrupter().
In both cases, the existing error handling within xhci_add_interrupter() is
redundant and unnecessary.
Upcoming Changes:
In the subsequent commit, interrupter initialization will move from
xhci_mem_init() to xhci_init(). This change is necessary to facilitate
the ability to restart the xHCI driver without re-allocating memory.
As a result, the allocated interrupter must be stored in the interrupters
pointer array before initialization.
Consequently, xhci_create_secondary_interrupter() would need to handle
pointer removal for allocated 'interrupters' array upon failure, although
xhci_add_interrupter() will never fail.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250515135621.335595-11-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Relocated the enabling of USB 3.0 device notifications from xhci_mem_init()
to xhci_init(). Introduced xhci_set_dev_notifications() function to handle
the notification settings.
Simplify 'DEV_NOTE_FWAKE' masks by directly using the 'ENABLE_DEV_NOTE'
value (1 << 1) instead of using the 'ENABLE_DEV_NOTE' macro.
Macro 'ENABLE_DEV_NOTE' is removed.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250515135621.335595-10-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the assignment of the doorbell array pointer from xhci_mem_init()
to xhci_init(). The assignment now utilizes the newly introduced
xhci_set_doorbell_ptr() function.
Doorbell Array Offset mask (DBOFF_MASK) is updated to directly specify its
bit range as 31:2, rather than using inverted reserved bits 1:0.
This change simplifies the mask representation, making it more intuitive
and easier to understand.
Remove the "// " prefix from trace messages, as it is unnecessary and
distracting.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250515135621.335595-9-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the Device Context Base Address Array (DCBAA) pointer write from
xhci_mem_init() to xhci_init(). This is part of the ongoing effort to
separate allocation and initialization.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250515135621.335595-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor xhci_set_cmd_ring_deq() making the code more understandable by
using more descriptive constants and separating operations logically.
- Remove 'CMD_RING_RSVD_BITS' the macro is misleading, the reserved bits
are 5:4, yet the mask is for bits 5:0.
- Introduce masks 'CMD_RING_PTR_MASK' and 'CMD_RING_CYCLE' to clearly
define the bits for the Command Ring pointer and Command Ring Cycle.
- Simplifying the process of setting the command ring address by separating
the DMA address calculation and the Command Ring Control register (crcr)
updates.
- Remove the "// " prefix from trace messages, as it is unnecessary and
distracting.
Note: In the current implementation, the cycle bit is not cleared before
applying the OR operation. Although this hasn't caused issues so far
because the bit is '0' before reaching this function, the bit is now
cleared before being set to prevent potential future problems and simplify
the process.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250515135621.335595-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move command ring pointer write from xhci_mem_init() to xhci_init(),
and utilize the xhci_set_cmd_ring_deq() function.
The xhci_set_cmd_ring_deq() function is nearly identical to the Command
Ring Control register code in xhci_mem_init(). The only notable change is
the use of:
xhci_trb_virt_to_dma(xhci->cmd_ring->deq_seg, xhci->cmd_ring->dequeue)
instead of:
xhci->cmd_ring->first_seg->dma
but they are effectively the same in this context. The former represents
the exact position of the dequeue pointer, while the latter is the first
DMA in the first segment. Before use, the dequeue pointer is at the first
DMA in the first segment.
The xhci_set_cmd_ring_deq() function is moved without modification, except
for (long unsigned long) -> (unsigned long long) due to checkpatch.pl.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250515135621.335595-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor the setting of the Number of Device Slots Enabled field into a
separate function, relocating it to xhci_init().
The xHCI driver consistently sets the number of enabled device slots to the
maximum value. The new function is named to reflect this behavior.
Remove the "// " prefix from trace messages, as it is unnecessary and
distracting.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250515135621.335595-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move pre-allocation initialization from xhci_mem_init() to xhci_init().
This change is part of an ongoing effort to separate initialization from
allocation within the xhci driver. By doing so, it will enable future
patches to re-initialize xhci driver memory without the necessity of fully
recreating it.
Additionally, compliance mode recovery initialization has been adjusted to
only occur after successful memory allocation.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250515135621.335595-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In many projects, you need to obtain the available bandwidth of the
xhci roothub port. Refer to xhci rev1_2 and use the TRB_GET_BW
command to obtain it.
hardware tested:
03:00.3 USB controller: Advanced Micro Devices, Inc. [AMD] Raven USB 3.1
(prog-if 30 [XHCI])
Subsystem: Huawei Technologies Co., Ltd. Raven USB 3.1
Flags: bus master, fast devsel, latency 0, IRQ 30
Memory at c0300000 (64-bit, non-prefetchable) [size=1M]
Capabilities: [48] Vendor Specific Information: Len=08 <?>
Capabilities: [50] Power Management version 3
Capabilities: [64] Express Endpoint, MSI 00
Capabilities: [a0] MSI: Enable- Count=1/8 Maskable- 64bit+
Capabilities: [c0] MSI-X: Enable+ Count=8 Masked-
Kernel driver in use: xhci_hcd
test progress:
1. cd /sys/kernel/debug/usb/xhci/0000:03:00.3/port_bandwidth# ls
FS_BW HS_BW SS_BW
2. test fs speed device
cat FS_BW
port[1] available bw: 90%.
port[2] available bw: 90%.
port[3] available bw: 90%.
port[4] available bw: 90%.
port[5] available bw: 0%.
port[6] available bw: 0%.
port[7] available bw: 0%.
port[8] available bw: 0%.
plug in fs usb audio ID 0d8c:013c
cat FS_BW
port[1] available bw: 76%.
port[2] available bw: 76%.
port[3] available bw: 76%.
port[4] available bw: 76%.
port[5] available bw: 0%.
port[6] available bw: 0%.
port[7] available bw: 0%.
port[8] available bw: 0%.
3. test hs speed device
cat HS_BW
port[1] available bw: 79%.
port[2] available bw: 79%.
port[3] available bw: 79%.
port[4] available bw: 79%.
port[5] available bw: 0%.
port[6] available bw: 0%.
port[7] available bw: 0%.
port[8] available bw: 0%.
plug in hs usb video ID 0408:1040
cat HS_BW
port[1] available bw: 39%.
port[2] available bw: 39%.
port[3] available bw: 39%.
port[4] available bw: 39%.
port[5] available bw: 0%.
port[6] available bw: 0%.
port[7] available bw: 0%.
port[8] available bw: 0%.
4.cat SS_BW
port[1] available bw: 0%.
port[2] available bw: 0%.
port[3] available bw: 0%.
port[4] available bw: 0%.
port[5] available bw: 90%.
port[6] available bw: 90%.
port[7] available bw: 90%.
port[8] available bw: 90%.
Signed-off-by: Xu Rao <raoxu@uniontech.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250515135621.335595-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The error message above used to span two lines, rarely more. A recent
cleanup concentrated useful information from it in one line, but then
it added printing the list of all ring segments, which is even longer
than before. It provides no new information in usual cases and little
in unusual ones, but adds noise to the log. Drop it.
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250515135621.335595-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This includes following USB4/Thunderbolt changes for the v6.16 merge
window:
- Enable wake on connect and disconnect over system suspend.
- Add mapping between Type-C ports and USB4 ports on non-Chrome systems.
- Expose tunneling related events to userspace.
All these have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----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=yU5Q
-----END PGP SIGNATURE-----
Merge tag 'thunderbolt-for-v6.16-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-next
Mika writes:
thunderbolt: Changes for v6.16 merge window
This includes following USB4/Thunderbolt changes for the v6.16 merge
window:
- Enable wake on connect and disconnect over system suspend.
- Add mapping between Type-C ports and USB4 ports on non-Chrome systems.
- Expose tunneling related events to userspace.
All these have been in linux-next with no reported issues.
* tag 'thunderbolt-for-v6.16-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt:
Documentation/admin-guide: Document Thunderbolt/USB4 tunneling events
thunderbolt: Notify userspace about firmware CM tunneling events
thunderbolt: Notify userspace about software CM tunneling events
thunderbolt: Introduce domain event message handler
usb: typec: Connect Type-C port with associated USB4 port
thunderbolt: Add Thunderbolt/USB4 <-> USB3 match function
thunderbolt: Expose usb4_port_index() to other modules
thunderbolt: Fix a logic error in wake on connect
thunderbolt: Use wake on connect and disconnect over suspend
A handful small fixes. The only significant change is the fix for
MIDI 2.0 UMP handling in ALSA sequencer, but as MIDI 2.0 stuff is
still new and rarely used, the impact should be pretty limited.
Other than that, quirks for USB-audio and a few cosmetic fixes and
changes in drivers that should be safe to apply.
-----BEGIN PGP SIGNATURE-----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=kbgJ
-----END PGP SIGNATURE-----
Merge tag 'sound-6.15-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A handful small fixes. The only significant change is the fix for MIDI
2.0 UMP handling in ALSA sequencer, but as MIDI 2.0 stuff is still new
and rarely used, the impact should be pretty limited.
Other than that, quirks for USB-audio and a few cosmetic fixes and
changes in drivers that should be safe to apply"
* tag 'sound-6.15-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: usb-audio: Add sample rate quirk for Microdia JP001 USB Camera
ALSA: es1968: Add error handling for snd_pcm_hw_constraint_pow2()
ALSA: sh: SND_AICA should depend on SH_DMA_API
ALSA: usb-audio: Add sample rate quirk for Audioengine D1
ALSA: ump: Fix a typo of snd_ump_stream_msg_device_info
ALSA/hda: intel-sdw-acpi: Correct sdw_intel_acpi_scan() function parameter
ALSA: seq: Fix delivery of UMP events to group ports
Commit aa7a9275ab ("PM: sleep: Suspend async parents after suspending
children") had triggered a suspend issue on Tegra boards because it had
reordered the syspend of devices with async suspend enabled with respect
to some other devices. Specifically, the devices with async suspend
enabled that have no children are now suspended before any other devices
unless there are device links pointing to them as suppliers.
The investigation that followed the failure report uncovered that async
suspend was enabled for the cypd4226 device that was a Type-C controller
with a dependency on USB PHY and it turned out that disabling async
suspend for that device made the issue go away. Since async suspend
takes dependencies between parents and children into account as well
as other dependencies between devices represented by device links, this
means that the cypd4226 has a dependency on another device that is
not represented in any form in the kernel (a "hidden" dependency), in
which case async suspend should not be enabled for it.
Accordingly, make ucsi_ccg_probe() disable async suspend for the
devices handled by, which covers the cypd4226 device on the Tegra
boards as well as other devices likely to have similar "hidden"
dependencies.
Fixes: aa7a9275ab ("PM: sleep: Suspend async parents after suspending children")
Closes: https://lore.kernel.org/linux-pm/c6cd714b-b0eb-42fc-b9b5-4f5f396fb4ec@nvidia.com/
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/6180608.lOV4Wx5bFT@rjwysocki.net
s/devince/device/
It's used only internally, so no any behavior changes.
Fixes: 37e0e14128 ("ALSA: ump: Support UMP Endpoint and Function Block parsing")
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://patch.msgid.link/20250511141147.10246-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
usb-storage is the last user of the block layer bounce buffering now,
and only uses it for HCDs that do not support DMA on highmem configs.
Remove this support and fail the probe so that the block layer bounce
buffering can go away.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20250505081138.3435992-5-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Event polling delay is set to 0 if there are any pending requests in
either rx or tx requests lists. Checking for pending requests does
not work well for "IN" transfers as the tty driver always queues
requests to the list and TRBs to the ring, preparing to receive data
from the host.
This causes unnecessary busylooping and cpu hogging.
Only set the event polling delay to 0 if there are pending tx "write"
transfers, or if it was less than 10ms since last active data transfer
in any direction.
Cc: Łukasz Bartosik <ukaszb@chromium.org>
Fixes: fb18e5bb96 ("xhci: dbc: poll at different rate depending on data transfer activity")
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250505125630.561699-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
VIA VL805 doesn't bother updating the EP Context cycle bit when the
endpoint halts. This is seen by patching xhci_move_dequeue_past_td()
to print the cycle bits of the EP Context and the TRB at hw_dequeue
and then disconnecting a flash drive while reading it. Actual cycle
state is random as expected, but the EP Context bit is always 1.
This means that the cycle state produced by this function is wrong
half the time, and then the endpoint stops working.
Work around it by looking at the cycle bit of TD's end_trb instead
of believing the Endpoint or Stream Context. Specifically:
- rename cycle_found to hw_dequeue_found to avoid confusion
- initialize new_cycle from td->end_trb instead of hw_dequeue
- switch new_cycle toggling to happen after end_trb is found
Now a workload which regularly stalls the device works normally for
a few hours and clearly demonstrates the HW bug - the EP Context bit
is not updated in a new cycle until Set TR Dequeue overwrites it:
[ +0,000298] sd 10:0:0:0: [sdc] Attached SCSI disk
[ +0,011758] cycle bits: TRB 1 EP Ctx 1
[ +5,947138] cycle bits: TRB 1 EP Ctx 1
[ +0,065731] cycle bits: TRB 0 EP Ctx 1
[ +0,064022] cycle bits: TRB 0 EP Ctx 0
[ +0,063297] cycle bits: TRB 0 EP Ctx 0
[ +0,069823] cycle bits: TRB 0 EP Ctx 0
[ +0,063390] cycle bits: TRB 1 EP Ctx 0
[ +0,063064] cycle bits: TRB 1 EP Ctx 1
[ +0,062293] cycle bits: TRB 1 EP Ctx 1
[ +0,066087] cycle bits: TRB 0 EP Ctx 1
[ +0,063636] cycle bits: TRB 0 EP Ctx 0
[ +0,066360] cycle bits: TRB 0 EP Ctx 0
Also tested on the buggy ASM1042 which moves EP Context dequeue to
the next TRB after errors, one problem case addressed by the rework
that implemented this loop. In this case hw_dequeue can be enqueue,
so simply picking the cycle bit of TRB at hw_dequeue wouldn't work.
Commit 5255660b20 ("xhci: add quirk for host controllers that
don't update endpoint DCS") tried to solve the stale cycle problem,
but it was more complex and got reverted due to a reported issue.
Cc: Jonathan Bell <jonathan@raspberrypi.org>
Cc: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250505125630.561699-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The read urb pointer is dereferenced before checking that it is non-NULL
during open(), but no check is needed as the existence of a bulk in
endpoint is verified during attach() since commit ef079936d3 ("USB:
serial: ti_usb_3410_5052: fix NULL-deref at open").
Drop the bogus read urb sanity check.
Signed-off-by: Johan Hovold <johan@kernel.org>
wait_event_interruptible_timeout returns a long
The return value was being assigned to an int causing an integer overflow
when the remaining jiffies > INT_MAX which resulted in random error
returns.
Use a long return value, converting to the int ioctl return only on error.
Fixes: bb99794a47 ("usb: usbtmc: Add ioctl for vendor specific read")
Cc: stable@vger.kernel.org
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Link: https://lore.kernel.org/r/20250502070941.31819-4-dpenkler@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
wait_event_interruptible_timeout returns a long
The return was being assigned to an int causing an integer overflow when
the remaining jiffies > INT_MAX resulting in random error returns.
Use a long return value, converting to the int ioctl return only on
error.
Fixes: 739240a9f6 ("usb: usbtmc: Add ioctl USBTMC488_IOCTL_WAIT_SRQ")
Cc: stable@vger.kernel.org
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Link: https://lore.kernel.org/r/20250502070941.31819-3-dpenkler@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
wait_event_interruptible_timeout returns a long
The return was being assigned to an int causing an integer overflow when
the remaining jiffies > INT_MAX resulting in random error returns.
Use a long return value and convert to int ioctl return only on error.
When the return value of wait_event_interruptible_timeout was <= INT_MAX
the number of remaining jiffies was returned which has no meaning for the
user. Return 0 on success.
Reported-by: Michael Katzmann <vk2bea@gmail.com>
Fixes: dbf3e7f654 ("Implement an ioctl to support the USMTMC-USB488 READ_STATUS_BYTE operation.")
Cc: stable@vger.kernel.org
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Link: https://lore.kernel.org/r/20250502070941.31819-2-dpenkler@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes Type-C Compliance Test TD 4.7.6 - Try.SNK DRP Connect
SNKAS.
The compliance tester moves into SNK_UNATTACHED during toggling and
expects the PUT to apply Rp after tPDDebounce of detection. If the port
is in SNK_TRY_WAIT_DEBOUNCE, it will move into SRC_TRYWAIT immediately
and apply Rp. This violates TD 4.7.5.V.3, where the tester confirms that
the PUT attaches Rp after the transitions to Unattached.SNK for
tPDDebounce.
Change the tcpm_set_state delay between SNK_TRY_WAIT_DEBOUNCE and
SRC_TRYWAIT to tPDDebounce.
Fixes: a0a3e04e6b ("staging: typec: tcpm: Check for Rp for tPDDebounce")
Cc: stable <stable@kernel.org>
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250429234703.3748506-2-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usbtmc_read() calls usbtmc_generic_read()
which uses interruptible sleep, but usbtmc_read()
itself uses uninterruptble sleep for mutual exclusion
between threads. That makes no sense.
Both should use interruptible sleep.
Fixes: 5b775f672c ("USB: add USB test and measurement class driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20250430134810.226015-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The controllers with rtl version larger than
RTL_REVISION_NEW_LPM (0x00002700) has bug which causes that controller
doesn't resume from L1 state. It happens if after receiving LPM packet
controller starts transitioning to L1 and in this moment the driver force
resuming by write operation to PORTSC.PLS.
It's corner case and happens when write operation to PORTSC occurs during
device delay before transitioning to L1 after transmitting ACK
time (TL1TokenRetry).
Forcing transition from L1->L0 by driver for revision larger than
RTL_REVISION_NEW_LPM is not needed, so driver can simply fix this issue
through block call of cdnsp_force_l0_go function.
Fixes: 3d82904559 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/PH7PR07MB9538B55C3A6E71F9ED29E980DD842@PH7PR07MB9538.namprd07.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch ensures that the UCSI driver waits for all pending tasks in the
ucsi_displayport_work workqueue to finish executing before proceeding with
the partner removal.
Cc: stable <stable@kernel.org>
Fixes: af8622f6a5 ("usb: typec: ucsi: Support for DisplayPort alt mode")
Signed-off-by: Andrei Kuchynski <akuchynski@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Link: https://lore.kernel.org/r/20250424084429.3220757-3-akuchynski@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch introduces the ucsi_con_mutex_lock / ucsi_con_mutex_unlock
functions to the UCSI driver. ucsi_con_mutex_lock ensures the connector
mutex is only locked if a connection is established and the partner pointer
is valid. This resolves a deadlock scenario where
ucsi_displayport_remove_partner holds con->mutex waiting for
dp_altmode_work to complete while dp_altmode_work attempts to acquire it.
Cc: stable <stable@kernel.org>
Fixes: af8622f6a5 ("usb: typec: ucsi: Support for DisplayPort alt mode")
Signed-off-by: Andrei Kuchynski <akuchynski@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250424084429.3220757-2-akuchynski@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Cypress HX3 USB3.0 hubs use different PID values depending
on the product variant. The comment in compatibles table is
misleading, as the currently used PIDs (0x6504 and 0x6506 for
USB 3.0 and USB 2.0, respectively) are defaults for the CYUSB331x,
while CYUSB330x and CYUSB332x variants use different values.
Based on the datasheet [1], update the compatible usb devices table
to handle different types of the hub.
The change also includes vendor mode PIDs, which are used by the
hub in I2C Master boot mode, if connected EEPROM contains invalid
signature or is blank. This allows to correctly boot the hub even
if the EEPROM will have broken content.
Number of vcc supplies and timing requirements are the same for all
HX variants, so the platform driver's match table does not have to
be extended.
[1] https://www.infineon.com/dgdl/Infineon-HX3_USB_3_0_Hub_Consumer_Industrial-DataSheet-v22_00-EN.pdf?fileId=8ac78c8c7d0d8da4017d0ecb53f644b8
Table 9. PID Values
Fixes: b43cd82a1a ("usb: misc: onboard-hub: add support for Cypress HX3 USB 3.0 family")
Cc: stable <stable@kernel.org>
Signed-off-by: Lukasz Czechowski <lukasz.czechowski@thaumatec.com>
Link: https://lore.kernel.org/r/20250425-onboard_usb_dev-v2-1-4a76a474a010@thaumatec.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Device tree bindings state that the clock is optional for UHCI platform
controllers, and some existing device trees don't provide those - such
as those for VIA/WonderMedia devices.
The driver however fails to probe now if no clock is provided, because
devm_clk_get returns an error pointer in such case.
Switch to devm_clk_get_optional instead, so that it could probe again
on those platforms where no clocks are given.
Cc: stable <stable@kernel.org>
Fixes: 26c502701c ("usb: uhci: Add clk support to uhci-platform")
Signed-off-by: Alexey Charkov <alchark@gmail.com>
Link: https://lore.kernel.org/r/20250425-uhci-clock-optional-v1-1-a1d462592f29@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently gadget_wakeup() waits for U0 synchronously if it was
called from func_wakeup(), this is because we need to send the
function wakeup command soon after the link is active. And the
call is made synchronous by polling DSTS continuosly for 20000
times in __dwc3_gadget_wakeup(). But it observed that sometimes
the link is not active even after polling 20K times, leading to
remote wakeup failures. Adding a small delay between each poll
helps, but that won't guarantee resolution in future. Hence make
the gadget_wakeup completely asynchronous.
Since multiple interfaces can issue a function wakeup at once,
add a new variable wakeup_pending_funcs which will indicate the
functions that has issued func_wakup, this is represented in a
bitmap format. If the link is in U3, dwc3_gadget_func_wakeup()
will set the bit corresponding to interface_id and bail out.
Once link comes back to U0, linksts_change irq is triggered,
where the function wakeup command is sent based on bitmap.
Cc: stable <stable@kernel.org>
Fixes: 92c08a84b5 ("usb: dwc3: Add function suspend and function wakeup support")
Signed-off-by: Prashanth K <prashanth.k@oss.qualcomm.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250422103231.1954387-4-prashanth.k@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently when the host sends GET_STATUS request for an interface,
we use get_status callbacks to set/clear remote wakeup capability
of that interface. And if get_status callback isn't present for
that interface, then we assume its remote wakeup capability based
on bmAttributes.
Now consider a scenario, where we have a USB configuration with
multiple interfaces (say ECM + ADB), here ECM is remote wakeup
capable and as of now ADB isn't. And bmAttributes will indicate
the device as wakeup capable. With the current implementation,
when host sends GET_STATUS request for both interfaces, we will
set FUNC_RW_CAP for both. This results in USB3 CV Chapter 9.15
(Function Remote Wakeup Test) failures as host expects remote
wakeup from both interfaces.
The above scenario is just an example, and the failure can be
observed if we use configuration with any interface except ECM.
Hence avoid configuring remote wakeup capability from composite
driver based on bmAttributes, instead use get_status callbacks
and let the function drivers decide this.
Cc: stable <stable@kernel.org>
Fixes: 481c225c48 ("usb: gadget: Handle function suspend feature selector")
Signed-off-by: Prashanth K <prashanth.k@oss.qualcomm.com>
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250422103231.1954387-3-prashanth.k@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When host sends GET_STATUS to ECM interface, handle the request
from the function driver. Since the interface is wakeup capable,
set the corresponding bit, and set RW bit if the function is
already armed for wakeup by the host.
Cc: stable <stable@kernel.org>
Fixes: 481c225c48 ("usb: gadget: Handle function suspend feature selector")
Signed-off-by: Prashanth K <prashanth.k@oss.qualcomm.com>
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250422103231.1954387-2-prashanth.k@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a USB device is connected to the OTG port, the tegra_xhci_id_work()
routine transitions the PHY to host mode and calls xhci_hub_control()
with the SetPortFeature command to enable port power.
In certain cases, the XHCI controller may be in a low-power state
when this operation occurs. If xhci_hub_control() is invoked while
the controller is suspended, the PORTSC register may return 0xFFFFFFFF,
indicating a read failure. This causes xhci_hc_died() to be triggered,
leading to host controller shutdown.
Example backtrace:
[ 105.445736] Workqueue: events tegra_xhci_id_work
[ 105.445747] dump_backtrace+0x0/0x1e8
[ 105.445759] xhci_hc_died.part.48+0x40/0x270
[ 105.445769] tegra_xhci_set_port_power+0xc0/0x240
[ 105.445774] tegra_xhci_id_work+0x130/0x240
To prevent this, ensure the controller is fully resumed before
interacting with hardware registers by calling pm_runtime_get_sync()
prior to the host mode transition and xhci_hub_control().
Fixes: f836e78430 ("usb: xhci-tegra: Add OTG support")
Cc: stable <stable@kernel.org>
Signed-off-by: Jim Lin <jilin@nvidia.com>
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Link: https://lore.kernel.org/r/20250422114001.126367-1-waynec@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In very rare cases after resuming controller from L1 to L0 it reads
registers before the clock UTMI have been enabled and as the result
driver reads incorrect value.
Most of registers are in APB domain clock but some of them (e.g. PORTSC)
are in UTMI domain clock.
After entering to L1 state the UTMI clock can be disabled.
When controller transition from L1 to L0 the port status change event is
reported and in interrupt runtime function driver reads PORTSC.
During this read operation controller synchronize UTMI and APB domain
but UTMI clock is still disabled and in result it reads 0xFFFFFFFF value.
To fix this issue driver increases APB timeout value.
The issue is platform specific and if the default value of APB timeout
is not sufficient then this time should be set Individually for each
platform.
Fixes: 3d82904559 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/PH7PR07MB953846C57973E4DB134CAA71DDBF2@PH7PR07MB9538.namprd07.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We identified a bug where the ST_RC bit in the status register was not
being acknowledged after clearing the CTRL_RUN bit in the control
register. This could lead to unexpected behavior in the USB gadget
drivers.
This patch resolves the issue by adding the necessary code to explicitly
acknowledge ST_RC after clearing CTRL_RUN based on the programming
sequence, ensuring proper state transition.
Fixes: 49db427232 ("usb: gadget: Add UDC driver for tegra XUSB device mode controller")
Cc: stable <stable@kernel.org>
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Link: https://lore.kernel.org/r/20250418081228.1194779-1-waynec@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Parade PS5511 is 4+1 port USB 3.2 gen 1 hub with a reset pin and two power
supplies (3V3 and 1V1).
Add the support for this hub for the reset pin control and power supply.
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20250422082957.2058229-5-treapking@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch enhances the HID gadget driver to support dynamic configuration
of the interrupt polling interval (bInterval) via configfs. A new
‘interval’ attribute is exposed under each HID function’s configfs
directory, and any write to it will adjust the poll rate for all endpoints
without requiring a rebuild.
When the attribute has never been written, legacy defaults are preserved:
• Full-Speed (FS) endpoints (IN & OUT) poll every 10 ms
• High-Speed (HS) endpoints (IN & OUT) poll every 4 micro-frames
(~1 ms)
To implement this cleanly:
• Add two new fields to f_hid_opts and f_hidg:
– unsigned char interval
– bool interval_user_set
• Introduce dedicated f_hid_opts_interval_show/store functions.
The store routine parses into an unsigned int, bounds‐checks,
assigns to opts->interval, and sets opts->interval_user_set = true.
• Initialize opts->interval = 4 and opts->interval_user_set = false in
hidg_alloc_inst(), then copy both into the live f_hidg instance in
hidg_alloc().
• In hidg_bind(), set each endpoint’s bInterval based on whether the
user has written the attribute:
– If interval_user_set == false, use FS=10 / HS=4
– If interval_user_set == true, use the user’s value for both FS
& HS
Signed-off-by: Ben Hoff <hoff.benjamin.k@gmail.com>
Link: https://lore.kernel.org/r/20250429182809.811786-1-hoff.benjamin.k@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for making the kmalloc family of allocators type aware,
we need to make sure that the returned type from the allocation matches
the type of the variable being assigned. (Before, the allocator would
always return "void *", which can be implicitly cast to any pointer type.)
The assigned type is "struct usb_function **" but the returned type
will be "struct usb_function ***". These are the same size allocation
(pointer size), but different types. Adjust the allocation type to match
the assignment.
Signed-off-by: Kees Cook <kees@kernel.org>
Link: https://lore.kernel.org/r/20250426062125.work.209-kees@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCgA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmgOrWseHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGFyIH/AhXcuA8y8rk43mo
t+0GO7JR4dnr4DIl74GgDjCXlXiKCT7EXMfD/ABdofTxV4Pbyv+pUODlg1E6eO9U
C1WWM5PPNBGDDEVSQ3Yu756nr0UoiFhvW0R6pVdou5cezCWAtIF9LTN8DEUgis0u
EUJD9+/cHAMzfkZwabjm/HNsa1SXv2X47MzYv/PdHKr0htEPcNHF4gqBrBRdACGy
FJtaCKhuPf6TcDNXOFi5IEWMXrugReRQmOvrXqVYGa7rfUFkZgsAzRY6n/rUN5Z9
FAgle4Vlv9ohVYj9bXX8b6wWgqiKRpoN+t0PpRd6G6ict1AFBobNGo8LH3tYIKqZ
b/dCGNg=
=xDGd
-----END PGP SIGNATURE-----
Merge 6.15-rc4 into usb-next
We need the USB fixes in here as well, and this resolves the following
merge conflicts that were reported in linux-next:
drivers/usb/chipidea/ci_hdrc_imx.c
drivers/usb/host/xhci.h
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement the remote wakeup capability for u_serial. The newly added
function gserial_wakeup_host() wakes up the host when there is some
data to be sent while the device is suspended. Add gser_get_status()
callbacks to advertise f_serial interface as function wakeup capable.
Signed-off-by: Prashanth K <prashanth.k@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250424121142.4180241-1-prashanth.k@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The use of the old SET_SYSTEM_SLEEP_PM_OPS/SET_RUNTIME_PM_OPS macros
without __maybe_unused annotations causes warnings when build testing
without CONFIG_PM:
drivers/usb/dwc3/dwc3-qcom.c:421:12: error: unused function 'dwc3_qcom_suspend' [-Werror,-Wunused-function]
421 | static int dwc3_qcom_suspend(struct dwc3_qcom *qcom, bool wakeup)
| ^~~~~~~~~~~~~~~~~
drivers/usb/dwc3/dwc3-qcom.c:457:12: error: unused function 'dwc3_qcom_resume' [-Werror,-Wunused-function]
457 | static int dwc3_qcom_resume(struct dwc3_qcom *qcom, bool wakeup)
Change these to the modern SYSTEM_SLEEP_PM_OPS/RUNTIME_PM_OPS/pm_ptr
macros, which avoids the warnings and improves readability at the same
time.
Fixes: 1881a32fe1 ("usb: dwc3: qcom: Transition to flattened model")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250423162613.2082417-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
debugfs.c emits the following warnings when compiling with the -Wsign-conversion flag with clang 15:
drivers/usb/typec/ucsi/debugfs.c:58:27: warning: implicit conversion changes signedness: 'int' to 'u32' (aka 'unsigned int') [-Wsign-conversion]
ucsi->debugfs->status = ret;
~ ^~~
drivers/usb/typec/ucsi/debugfs.c:71:25: warning: implicit conversion changes signedness: 'u32' (aka 'unsigned int') to 'int' [-Wsign-conversion]
return ucsi->debugfs->status;
~~~~~~ ~~~~~~~~~~~~~~~^~~~~~
During ucsi_cmd() we see:
if (ret < 0) {
ucsi->debugfs->status = ret;
return ret;
}
But "status" is u32 meaning unsigned wrap-around occurs when assigning a value which is < 0 to it, this obscures the real status.
To fix this make the "status" of type int since ret is also of type int.
Fixes: df0383ffad ("usb: typec: ucsi: Add debugfs for ucsi commands")
Cc: stable@vger.kernel.org
Signed-off-by: Qasim Ijaz <qasdev00@gmail.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250422134717.66218-1-qasdev00@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As demonstrated by the fix for update_port_device_state,
commit 12783c0b9e ("usb: core: Prevent null pointer dereference in update_port_device_state"),
usb_hub_to_struct_hub() can return NULL in certain scenarios,
such as during hub driver unbind or teardown race conditions,
even if the underlying usb_device structure exists.
Plus, all other places that call usb_hub_to_struct_hub() in the same file
do check for NULL return values.
If usb_hub_to_struct_hub() returns NULL, the subsequent access to
hub->ports[udev->portnum - 1] will cause a null pointer dereference.
Signed-off-by: Chenyuan Yang <chenyuan0y@gmail.com>
Fixes: f1bfb4a6fe ("usb: acpi: add device link between tunneled USB3 device and USB4 Host Interface")
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20250417195032.1811338-1-chenyuan0y@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is possible that the gadget will be disabled, while the udc is
suspended. When enabling the udc in that case, the clock gating
will not be enabled again. Leaving the phy unclocked. Even when the
udc is not enabled, connecting this powered but not clocked phy leads
to enumeration errors on the host side.
To ensure that the clock gating will be in an valid state, we ensure
that the clock gating will be enabled before stopping the udc.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Link: https://lore.kernel.org/r/20250417-dwc2_clock_gating-v1-1-8ea7c4d53d73@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enabling the compile test should not cause automatic enabling of all
drivers, but only allow to choose to compile them.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250417074634.81295-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The fsa4480 vcc lane could be driven by some external regulator.
This patch is adding support to enable the regulator before probing.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250404-ml-topic-typec-mux-fs4480-v1-1-475377ef22a3@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update struct hid_descriptor to better reflect the mandatory and
optional parts of the HID Descriptor as per USB HID 1.11 specification.
Note: the kernel currently does not parse any optional HID class
descriptors, only the mandatory report descriptor.
Update all references to member element desc[0] to rpt_desc.
Add test to verify bLength and bNumDescriptors values are valid.
Replace the for loop with direct access to the mandatory HID class
descriptor member for the report descriptor. This eliminates the
possibility of getting an out-of-bounds fault.
Add a warning message if the HID descriptor contains any unsupported
optional HID class descriptors.
Reported-by: syzbot+c52569baf0c843f35495@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=c52569baf0c843f35495
Fixes: f043bfc98c ("HID: usbhid: fix out-of-bounds bug")
Cc: stable@vger.kernel.org
Signed-off-by: Terry Junge <linuxhid@cosmicgizmosystems.com>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Here's a new simple driver for Owon oscilloscopes and a couple of new
new modem and smart meter device ids.
All have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCaAEdDwAKCRALxc3C7H1l
CKzKAP4wLuhXe44cO2OqDP4yDXBl+GR5H8k1t6uPO0dQ9A7mXAEA3h9JNmDy34ym
9HKNKBXiw7fUqWSb904XwEQmNXnFfA4=
=SrVq
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-6.15-rc3' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial device ids for 6.15-rc3
Here's a new simple driver for Owon oscilloscopes and a couple of new
new modem and smart meter device ids.
All have been in linux-next with no reported issues.
* tag 'usb-serial-6.15-rc3' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: simple: add OWON HDS200 series oscilloscope support
USB: serial: ftdi_sio: add support for Abacus Electrics Optical Probe
USB: serial: option: add Sierra Wireless EM9291
If USB3.x device references USB4 host interface, USB4 port can be
connected with appropriate Type-C port. By using component framework,
and in turn by creating symlinks, userspace can benefit from having
Thunderbolt/USB4 connection to Type-C ports.
Note: This change introduces dependency on Thunderbolt driver as it's
required to properly map USB4 port to Type-C port.
Signed-off-by: Alan Borzeszkowski <alan.borzeszkowski@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Add serial support for OWON HDS200 series oscilloscopes and likely
many other pieces of OWON test equipment.
OWON HDS200 series devices host two USB endpoints, designed to
facilitate bidirectional SCPI. SCPI is a predominately ASCII text
protocol for test/measurement equipment. Having a serial/tty interface
for these devices lowers the barrier to entry for anyone trying to
write programs to communicate with them.
The following shows the USB descriptor for the OWON HDS272S running
firmware V5.7.1:
Bus 001 Device 068: ID 5345:1234 Owon PDS6062T Oscilloscope
Negotiated speed: Full Speed (12Mbps)
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 [unknown]
bDeviceSubClass 0 [unknown]
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x5345 Owon
idProduct 0x1234 PDS6062T Oscilloscope
bcdDevice 1.00
iManufacturer 1 oscilloscope
iProduct 2 oscilloscope
iSerial 3 oscilloscope
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 0x0029
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 5 Physical Interface Device
bInterfaceSubClass 0 [unknown]
bInterfaceProtocol 0
iInterface 0
** UNRECOGNIZED: 09 21 11 01 00 01 22 5f 00
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 32
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 32
Device Status: 0x0000
(Bus Powered)
OWON appears to be using the same USB Vendor and Product ID for many
of their oscilloscopes. Looking at the discussion about the USB
vendor/product ID, in the link bellow, suggests that this VID/PID is
shared with VDS, SDS, PDS, and now the HDS series oscilloscopes.
Available documentation for these devices seems to indicate that all
use a similar SCPI protocol, some with RS232 options. It is likely that
this same simple serial setup would work correctly for them all.
Link: https://usb-ids.gowdy.us/read/UD/5345/1234
Signed-off-by: Craig Hesling <craig@hesling.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Abacus Electrics makes optical probes for interacting with smart meters
over an optical interface.
At least one version uses an FT232B chip (as detected by ftdi_sio) with
a custom USB PID, which needs to be added to the list to make the device
work in a plug-and-play fashion.
Signed-off-by: Michael Ehrenreich <michideep@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
We recently added some locking to this function but this error path
was accidentally missed. Unlock before returning.
Fixes: ec27386de2 ("usb: typec: class: Fix NULL pointer access")
Cc: stable <stable@kernel.org>
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/Z_44tOtmml89wQcM@stanley.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SanDisk 3.2Gen1 Flash Drive, which VID:PID is in 0781:55a3,
just like Silicon Motion Flash Drive:
https://lore.kernel.org/r/20250401023027.44894-1-limiao870622@163.com
also needs the DELAY_INIT quirk, or it will randomly work incorrectly
(e.g.: lsusb and can't list this device info) when connecting Huawei
hisi platforms and doing thousand of reboot test circles.
Cc: stable <stable@kernel.org>
Signed-off-by: Miao Li <limiao@kylinos.cn>
Signed-off-by: Lei Huang <huanglei@kylinos.cn>
Link: https://lore.kernel.org/r/20250414062935.159024-1-limiao870622@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The variable tpgt in usbg_make_tpg() is defined as unsigned long and is
assigned to tpgt->tport_tpgt, which is defined as u16. This may cause an
integer overflow when tpgt is greater than USHRT_MAX (65535). I
haven't tried to trigger it myself, but it is possible to trigger it
by calling usbg_make_tpg() with a large value for tpgt.
I modified the type of tpgt to match tpgt->tport_tpgt and adjusted the
relevant code accordingly.
This patch is similar to commit 59c816c1f2 ("vhost/scsi: potential
memory corruption").
Signed-off-by: Chen Yufeng <chenyufeng@iie.ac.cn>
Link: https://lore.kernel.org/r/20250415065857.1619-1-chenyufeng@iie.ac.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB IP-block found in most Qualcomm platforms is modelled in the
Linux kernel as 3 different independent device drivers, but as shown by
the already existing layering violations in the Qualcomm glue driver
they can not be operated independently.
With the current implementation, the glue driver registers the core and
has no way to know when this is done. As a result, e.g. the suspend
callbacks needs to guard against NULL pointer dereferences when trying
to peek into the struct dwc3 found in the drvdata of the child.
Even with these checks, there are no way to fully protect ourselves from
the race conditions that occur if the DWC3 is unbound.
Missing from the upstream Qualcomm USB support is handling of role
switching, in which the glue needs to be notified upon DRD mode changes.
Several attempts has been made through the years to register callbacks
etc, but they always fall short when it comes to handling of the core's
probe deferral on resources etc.
Moving to a model where the DWC3 core is instantiated in a synchronous
fashion avoids above described race conditions.
It is however not feasible to do so without also flattening the
DeviceTree binding, as assumptions are made in the DWC3 core and
frameworks used that the device's associated of_node will the that of
the core. Furthermore, the DeviceTree binding is a direct
representation of the Linux driver model, and doesn't necessarily
describe "the USB IP-block".
The Qualcomm DWC3 glue driver is therefor transitioned to initialize and
operate the DWC3 within the one device context, in synchronous fashion.
To provide a limited time backwards compatibility, a snapshot of the
driver is retained in a previous commit. As such no care is taken in the
dwc3-qcom driver for the qcom,dwc3 backwards compatibility.
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Signed-off-by: Bjorn Andersson <bjorn.andersson@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250414-dwc3-refactor-v7-6-f015b358722d@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the upcoming transition to a model where DWC3 core and glue operate
on a single struct device the drvdata datatype will change to be owned
by the core.
The drvdata is however used by the Qualcomm DWC3 glue to pass the qcom
glue context around before the core is allocated.
Remove this problem, and clean up the code, by passing the dwc3_qcom
struct around during probe, instead of acquiring it from the drvdata.
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Signed-off-by: Bjorn Andersson <bjorn.andersson@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250414-dwc3-refactor-v7-5-f015b358722d@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the core is integrated with glue, it's reasonable to assume that
the glue driver will have to touch the IP before/after the core takes
the hardware out and into reset. As such the glue must own these
resources and be allowed to turn them on/off outside the core's
handling.
Allow the platform or glue layer to indicate if the core logic for
clocks and resets should be skipped to deal with this.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Signed-off-by: Bjorn Andersson <bjorn.andersson@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250414-dwc3-refactor-v7-4-f015b358722d@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DWC3 IP block is handled by three distinct device drivers: XHCI,
DWC3 core and a platform specific (optional) DWC3 glue driver.
This has resulted in, at least in the case of the Qualcomm glue, the
presence of a number of layering violations, where the glue code either
can't handle, or has to work around, the fact that core might not probe
deterministically.
An example of this is that the suspend path should operate slightly
different depending on the device operating in host or peripheral mode,
and the only way to determine the operating state is to peek into the
core's drvdata.
The Qualcomm glue driver is expected to make updates in the qscratch
register region (the "glue" region) during role switch events, but with
the glue and core split using the driver model, there is no reasonable
way to introduce listeners for mode changes.
Split the dwc3 core platform_driver callbacks and their implementation
and export the implementation, to make it possible to deterministically
instantiate the dwc3 core as part of the dwc3 glue drivers and to
allow flattening of the DeviceTree representation.
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Signed-off-by: Bjorn Andersson <bjorn.andersson@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250414-dwc3-refactor-v7-3-f015b358722d@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to more tightly integrate the Qualcomm glue driver with the
dwc3 core the driver is redesigned to avoid splitting the implementation
using the driver model. But due to the strong coupling to the Devicetree
binding needs to be updated as well.
Various ways to provide backwards compatibility with existing Devicetree
blobs has been explored, but migrating the Devicetree information
between the old and the new binding is non-trivial.
For the vast majority of boards out there, the kernel and Devicetree are
generated and handled together, which in practice means that backwards
compatibility needs to be managed across about 1 kernel release.
For some though, such as the various Snapdragon laptops, the Devicetree
blobs live a life separate of the kernel. In each one of these, with the
continued extension of new features, it's recommended that users would
upgrade their Devicetree somewhat frequently.
With this in mind, simply carrying a snapshot/copy of the current driver
is simpler than creating and maintaining the migration code.
The driver is kept under the same Kconfig option, to ensure that Linux
distributions doesn't drop USB support on these platforms.
The driver, which is going to be refactored to handle the newly
introduced qcom,snps-dwc3 compatible, is updated to temporarily not
match against any compatible.
This driver should be removed after the next LTS release.
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Signed-off-by: Bjorn Andersson <bjorn.andersson@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250414-dwc3-refactor-v7-1-f015b358722d@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Realtek RTL8188ETV 2.4 GHz WiFi modules (detected as RTL8188EU by the
RTL8XXXXU driver) are found soldered into some embedded devices, such as
the Fernsehfee 3.0 set-top box.
They require a 3.3V power supply.
Signed-off-by: J. Neuschäfer <j.ne@posteo.net>
Link: https://lore.kernel.org/r/20250408-rtl-onboard-v2-2-0b6730b90e31@posteo.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is not understandable without a comment on endianness
Fixes: afba937e54 ("USB: CDC WDM driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20250401084749.175246-5-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
wdm_wwan_port_tx_complete is called from a completion
handler with irqs disabled and possible in IRQ context
usb_autopm_put_interface can take a mutex.
Hence usb_autopm_put_interface_async must be used.
Fixes: cac6fb015f ("usb: class: cdc-wdm: WWAN framework integration")
Cc: stable <stable@kernel.org>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20250401084749.175246-4-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clearing WDM_WWAN_IN_USE must be the last action or
we can open a chardev whose URBs are still poisoned
Fixes: cac6fb015f ("usb: class: cdc-wdm: WWAN framework integration")
Cc: stable <stable@kernel.org>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20250401084749.175246-3-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case submitting the URB fails we must undo
what we've done so far.
Fixes: cac6fb015f ("usb: class: cdc-wdm: WWAN framework integration")
Cc: stable <stable@kernel.org>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20250401084749.175246-2-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The event count is read from register DWC3_GEVNTCOUNT.
There is a check for the count being zero, but not for exceeding the
event buffer length.
Check that event count does not exceed event buffer length,
avoiding an out-of-bounds access when memcpy'ing the event.
Crash log:
Unable to handle kernel paging request at virtual address ffffffc0129be000
pc : __memcpy+0x114/0x180
lr : dwc3_check_event_buf+0xec/0x348
x3 : 0000000000000030 x2 : 000000000000dfc4
x1 : ffffffc0129be000 x0 : ffffff87aad60080
Call trace:
__memcpy+0x114/0x180
dwc3_interrupt+0x24/0x34
Signed-off-by: Frode Isaksen <frode@meta.com>
Fixes: 72246da40f ("usb: Introduce DesignWare USB3 DRD Driver")
Cc: stable <stable@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250403072907.448524-1-fisaksen@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Version 1.60 specifically needs this quirk.
Version 2.00 is known good.
Cc: stable <stable@kernel.org>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20250403180004.343133-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Silicon Motion Flash Drive connects to Huawei hisi platforms and
performs a system reboot test for two thousand circles, it will
randomly work incorrectly on boot, set DELAY_INIT quirk can workaround
this issue.
Signed-off-by: Miao Li <limiao@kylinos.cn>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20250401023027.44894-1-limiao870622@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The OHCI controller (rev 0x02) under LS7A PCI host has a hardware flaw.
MMIO register with offset 0x60/0x64 is treated as legacy PS2-compatible
keyboard/mouse interface, which confuse the OHCI controller. Since OHCI
only use a 4KB BAR resource indeed, the LS7A OHCI controller's 32KB BAR
is wrapped around (the second 4KB BAR space is the same as the first 4KB
internally). So we can add an 4KB offset (0x1000) to the OHCI registers
(from the PCI BAR resource) as a quirk.
Cc: stable <stable@kernel.org>
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Mingcong Bai <baimingcong@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Link: https://lore.kernel.org/r/20250328040059.3672979-1-chenhuacai@loongson.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "reset" GPIO controls the RESET signal to an external, usually
ULPI PHY, chip. The original code path acquires the signal in LOW
state, and then immediately asserts it HIGH again, if the reset
signal defaulted to asserted, there'd be a short "spike" before the
reset.
Here is what happens depending on the pre-existing state of the reset
signal:
Reset (previously asserted): ~~~|_|~~~~|_______
Reset (previously deasserted): _____|~~~~|_______
^ ^ ^
A B C
At point A, the low going transition is because the reset line is
requested using GPIOD_OUT_LOW. If the line is successfully requested,
the first thing we do is set it high _without_ any delay. This is
point B. So, a glitch occurs between A and B.
Requesting the line using GPIOD_OUT_HIGH eliminates the A and B
transitions. Instead we get:
Reset (previously asserted) : ~~~~~~~~~~|______
Reset (previously deasserted): ____|~~~~~|______
^ ^
A C
Where A and C are the points described above in the code. Point B
has been eliminated.
The issue was found during code inspection.
Also remove the cryptic "toggle ulpi .." comment.
Fixes: ca05b38252 ("usb: dwc3: xilinx: Add gpio-reset support")
Cc: stable <stable@kernel.org>
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250318064518.9320-1-mike.looijmans@topic.nl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The cdns3 driver has the same NCM deadlock as fixed in cdnsp by commit
58f2fcb3a8 ("usb: cdnsp: Fix deadlock issue during using NCM gadget").
Under PREEMPT_RT the deadlock can be readily triggered by heavy network
traffic, for example using "iperf --bidir" over NCM ethernet link.
The deadlock occurs because the threaded interrupt handler gets
preempted by a softirq, but both are protected by the same spinlock.
Prevent deadlock by disabling softirq during threaded irq handler.
Cc: stable <stable@kernel.org>
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Acked-by: Peter Chen <peter.chen@kernel.org>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20250318-rfs-cdns3-deadlock-v2-1-bfd9cfcee732@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_phy_init() may return an error code if e.g. its implementation fails
to prepare/enable some clocks. And properly rollback on probe error path
by calling the counterpart usb_phy_shutdown().
Found by Linux Verification Center (linuxtesting.org).
Fixes: be9cae2479 ("usb: chipidea: imx: Fix ULPI on imx53")
Cc: stable <stable@kernel.org>
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20250316102658.490340-4-pchelkin@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Upon encountering errors during the HSIC pinctrl handling section the
regulator should be disabled.
Use devm_add_action_or_reset() to let the regulator-disabling routine be
handled by device resource management stack.
Found by Linux Verification Center (linuxtesting.org).
Fixes: 4d6141288c ("usb: chipidea: imx: pinctrl for HSIC is optional")
Cc: stable <stable@kernel.org>
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20250316102658.490340-3-pchelkin@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usbmisc is an optional device property so it is totally valid for the
corresponding data->usbmisc_data to have a NULL value.
Check that before dereferencing the pointer.
Found by Linux Verification Center (linuxtesting.org) with Svace static
analysis tool.
Fixes: 74adad5003 ("usb: chipidea: ci_hdrc_imx: decrement device's refcount in .remove() and in the error path of .probe()")
Cc: stable <stable@kernel.org>
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20250316102658.490340-2-pchelkin@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These drivers have no way to probe as there are no match tables nor
devices created with a matching name in the kernel tree.
Marvell UDC was only ever supported by board files which were removed
in 2022.
For Marvell U3D, which was added in 2012, the PXA2128 aka MMP3 support
was never upstreamed with board files and only revived in 2019 with DT
support. No U3D DT support has been added since then.
The PLX net2272 driver was formerly used on blackfin. It also has PCI
support, but that appears to be only for a development board which is
likely unused given this device dates back to 2006.
Cc: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20250407191756.3584261-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current implementation of the usb-conn-gpio driver uses a fixed
"usb-charger" name for all USB connector devices. This causes conflicts
in the power supply subsystem when multiple USB connectors are present,
as duplicate names are not allowed.
Use IDA to manage unique IDs for naming usb connectors (e.g.,
usb-charger-0, usb-charger-1).
Signed-off-by: Chance Yang <chance.yang@kneron.us>
Link: https://lore.kernel.org/r/20250411-work-next-v3-1-7cd9aa80190c@kneron.us
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix a typo in the comment by correcting "deviece" to "device"
for clarity and readability.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20250407105002.107181-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update the comment to reference `usbhs_mod_probe()` instead of
`usbhs_mod_init()`, and replace `dev_set_drvdata()` with
`platform_set_drvdata()`, as these are the correct functions used
in this context.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20250407105002.107181-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enabling LPM is done in hub workqueue, often in paths handling possible
link issues. So fail immediately on USB3 LPM issues and avoid hub wq
from unnecessary blocking, thus allowing it to handle other port events
faster.
Detect errors when enabling U1/U2 link states, and return immediately
if there is an issue.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250314142000.93090-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several usb requests are needed to allow a USB3 link to enter U1/U2
hardware link power management LPM states. Reorder these requests
and send the more significant and likely to succeed first.
This is similar to the change done for disabling LPM
Enable LPM by first sending requests to the upstream hub of the device
SetPortFeature(U1_TIMEOUT)
SetPortFeature(U2_TIMEOUT)
These are more likely to succeed due to the shorter path, and LPM can
be considered enabled as link may go to U1/U2 LPM states after those.
Send the requests to the device after this, they allow the device
to initialte U1/U2 link transitions. Hub can already initiate U1/U2
SetFeature(U1_ENABLE)
SetFeature(U2_ENABLE)
Fail fast and bail out if a requests to the device fails.
This changes device initated LPM policy a bit. Device is no longer
able to initiate U2 if it failed or is not allowed to initiate
U1.
Enabling and disabling Link power management is done as part of
hub work. Avoid trying to send additional USB requests to a device
when there are known issues. It just causes hub work to block for
even longer.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250314142000.93090-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enabling device initiated USB3 link power management (LPM) may fail for
various reasons such as too long system exit latency, or link issues.
These are not good reason to disable hub initiated LPM U1/U2
states, especially as it requires sending more requests over a
possibly broken link, causing the hub work to block for even longer.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250314142000.93090-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move device configured check into usb_device_may_initiate_lpm() instead
of calling it before the function.
No functional changes, helps rework to fail faster during link power
management (LPM) enabling.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250314142000.93090-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several usb requests are needed to allow or forbid a USB3 link from
going into U1 or U2 hardware link power management (LPM) states.
Fail fast on issues in LPM disabling path. LPM disabling is done in hub
workqueue paths that are often already handling possible link issues.
Enabling and disabling LPM involves four usb requests.
Two requests sent to the upstream hub of the connected device:
SetPortFeature(U1_TIMEOUT)
SetPortFeature(U2_TIMEOUT)
And two to the device itself:
SetFeature(U1_ENABLE)
SetFeature(U2_ENABLE)
The requests to the hub sets the inactivity timeout used by the hub to
know when to initiate U1 and U2 LPM link state transitions.
These requests are also used prevent U1/U2 LPM transitions completely
by passing zero timeout value.
The requsts sent to the device only controls if device is allowed to
initiate U1/U2 transitions. If not enabled then only hub initiates U1/U2
transitions. Hub may block these device initiated attempts.
Reorder and send the hub requests first, these are more likely to succeed
due to shorter path, and we can consider LPM disabled if these succeed
as U1/U2 link state can not be entered after that.
Fail immediately if a request fails, and don't try to enable back LPM
after a failed request, that will just send more LPM requests over a
bad link.
If a device request controlling device initiateed LPM fails then exit
immediately, but consider LPM disabled at this stage.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250314142000.93090-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When creating a device path in the driver the snprintf() takes
up to 16 characters long argument along with the additional up to
12 characters for the signed integer (as it can't see the actual limits)
and tries to pack this into 16 bytes array. GCC complains about that
when build with `make W=1`:
drivers/usb/core/usb.c:705:25: note: ‘snprintf’ output between 3 and 28 bytes into a destination of size 16
Since everything works until now, let's just check for the potential
buffer overflow and bail out. It is most likely a never happen situation,
but at least it makes GCC happy.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250321164949.423957-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On i.MX95 platform, USB wakeup setting is controlled by HSIO Block
Control:
HSIO Block Control Overview:
- The HSIO block control include configuration and status registers that
provide miscellaneous top-level controls for clocking, beat limiter
enables, wakeup signal enables and interrupt status for the PCIe and USB
interfaces.
The wakeup function of HSIO blkctl is basically same as non-core, except
improvements about power lost cases. This will add the wakeup setting for
HSIO blkctl on i.MX95. It will firstly ioremap hsio blkctl memory, then do
wakeup setting as needs.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Jun Li <jun.li@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20250318150908.1583652-4-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In previous imx platform, normal USB controller interrupt and wakeup
interrupt are bound to one irq line. However, it changes on latest
i.MX95 platform since it has a dedicated irq line for wakeup interrupt.
This will add wakeup interrupt handling for i.MX95 to support various
wakeup events.
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20250318150908.1583652-3-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the course of fixing up the usages of flexible arrays, Gustavo
submitted a patch updating the ehci-fsl driver. However, the patch
was wrong because the driver was using the .priv member of the
ehci_hcd structure incorrectly. The private data is not supposed to
be a wrapper containing the ehci_hcd structure; it is supposed to be a
sub-structure stored in the .priv member.
Fix the problem by replacing the ehci_fsl structure with
ehci_fsl_priv, containing only the private data, along with a suitable
conversion macro for accessing it. This removes the problem of having
data follow a flexible array member.
Reported-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/linux-usb/Z-R9BcnSzrRv5FX_@kspp/
Reviewed-by: Kees Cook <kees@kernel.org>
Link: https://lore.kernel.org/r/8139e4cc-4e5c-40e2-9c4b-717ad3215868@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't set WDM_READ flag in wdm_in_callback() for ZLP-s, otherwise when
userspace tries to poll for available data, it might - incorrectly -
believe there is something available, and when it tries to non-blocking
read it, it might get stuck in the read loop.
For example this is what glib does for non-blocking read (briefly):
1. poll()
2. if poll returns with non-zero, starts a read data loop:
a. loop on poll() (EINTR disabled)
b. if revents was set, reads data
I. if read returns with EINTR or EAGAIN, goto 2.a.
II. otherwise return with data
So if ZLP sets WDM_READ (#1), we expect data, and try to read it (#2).
But as that was a ZLP, and we are doing non-blocking read, wdm_read()
returns with EAGAIN (#2.b.I), so loop again, and try to read again
(#2.a.).
With glib, we might stuck in this loop forever, as EINTR is disabled
(#2.a).
Signed-off-by: Robert Hodaszi <robert.hodaszi@digi.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20250403144004.3889125-1-robert.hodaszi@digi.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function don't return value, remove the invalid comment.
Signed-off-by: Li Qiong <liqiong@nfschina.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20250314101639.424013-1-liqiong@nfschina.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Similar to how it is done in the write path.
Add a disabled flag to track the function state and use it to exit the read
loops to ensure no readers get stuck when the function is disabled/unbound,
protecting against corruption when the waitq and spinlocks are reinitialized
in hidg_bind().
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Link: https://lore.kernel.org/r/20250318152207.330997-1-peter@korsgaard.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-Wflex-array-member-not-at-end was introduced in GCC-14, and we are
getting ready to enable it, globally.
Move the conflicting declaration to the end of the structure. Notice
that `struct uvc_input_header_descriptor` is a flexible structure --a
structure that contains a flexible-array member.
With this, fix three of the following warnings:
drivers/usb/gadget/function/uvc_configfs.h:77:57: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <kees@kernel.org>
Link: https://lore.kernel.org/r/Z9dyY7_ydJiGqh_d@kspp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
strncpy() is deprecated for NUL-terminated destination buffers; use
strscpy() instead. Since kzalloc() already zeroes out the destination
buffer, the potential NUL-padding by strncpy() is unnecessary. strscpy()
copies only the required characters and guarantees NUL-termination.
Since the destination buffer has a fixed length, strscpy() automatically
determines its size using sizeof() when the argument is omitted. This
makes an explicit sizeof() call unnecessary.
The source string is also NUL-terminated and meets the __must_be_cstr()
requirement of strscpy().
No functional changes intended.
Link: https://github.com/KSPP/linux/issues/90
Cc: linux-hardening@vger.kernel.org
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Reviewed-by: Kees Cook <kees@kernel.org>
Link: https://lore.kernel.org/r/20250320165647.34859-2-thorsten.blum@linux.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dwc3 device suspend/resume callbacks were being triggered during system
suspend and resume even if the device was already runtime-suspended.
This is redundant for device mode because the suspend and resume routines
are essentially identical for system PM and runtime PM.
To prevent these unnecessary callbacks, indicate to the PM core that it
can safely leave the device in runtime suspend if it's already
runtime-suspended in device mode by returning a positive value in
prepare() callback. This optimization only applies to devices without
pinctrl, as pinctrl has distinct logic tied to system suspend/resume.
Signed-off-by: Roy Luo <royluo@google.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250312223434.3071598-1-royluo@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Although some Type-C DRD devices that do not support the DP Sink
function (such as Huawei Mate 40Pro), the Source Port initiates
Enter Mode CMD, but the device responds to Enter Mode ACK, the
Source port then initiates DP Status Update CMD, and the device
responds to DP Status Update NAK.
As PD2.0 spec ("6.4.4.3.4 Enter Mode Command")，A DR_Swap Message
Shall Not be sent during Modal Operation between the Port Partners.
At this time, the source port initiates DR_Swap message through the
"echo device > /sys/class/typec/port0/data_role" command to switch
the data role from host to device. The device will initiate a Hard
Reset for recovery, resulting in the failure of data role swap.
Therefore, when DP Status Update NAK is received, Exit Mode CMD is
initiated to exit the currently entered DP altmode.
Signed-off-by: Jos Wang <joswang@lenovo.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250209071926.69625-1-joswang1221@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Device can be unbound, so driver must also release memory for the wakeup
source.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250406204051.63446-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Device can be unbound, so driver must also release memory for the wakeup
source.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250406204051.63446-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tcpci chip vbus pin is possibly driven by an regulator. This patch
is adding support to enable an optional vdd regulator before probing.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250404-ml-topic-tcpci-v1-1-4442c7d0ee1e@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The funciton tcpm_acc_attach is not setting the proper state when
calling tcpm_set_role. The function tcpm_set_role is currently only
handling TYPEC_STATE_USB. For the tcpm_acc_attach to switch into other
modal states tcpm_set_role needs to be extended by an extra state
parameter. This patch is handling the proper state change when calling
tcpm_acc_attach.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250404-ml-topic-tcpm-v1-3-b99f44badce8@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch extends the is_debug macro to cover the sink case (ufp). It
also handles the transition to access the DEBUG_ACC_ATTACHED state in
the sink case. It also handles the debounce case in which the cc
pins are not immediately valid after the plug event.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250404-ml-topic-tcpm-v1-2-b99f44badce8@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the function tcpm_acc_attach is not setting the data and role for
for the sink case we extend it to check for it first.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250404-ml-topic-tcpm-v1-1-b99f44badce8@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the typec connectors can have many muxes or switches for different
lanes (sbu, usb2, usb3) going into different modal states (usb2, usb3,
audio, debug) all of them will be called on typec_switch_set and
typec_mux_set. But not all of them will be handling the expected mode.
If one of the mux or switch will come back with EOPTNOSUPP this is no
reason to stop running through the next ones. Therefor we skip this
particular error value and continue calling the next.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250404-ml-topic-typec-mux-v1-1-22c0526381ba@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added the UCSI commands UCSI_GET_CAM_SUPPORTED, UCSI_GET_PD_MESSAGE,
UCSI_GET_ATTENTION_VDO and UCSI_SET_USB support in debugfs to enhance
PD/TypeC debugging capability
Signed-off-by: Madhu M <madhu.m@intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250402070817.1016635-1-madhu.m@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Huawei Matebook E Go tablet implements the UCSI interface in the
onboard EC. Add the glue driver to interface with the platform's UCSI
implementation.
This driver is inspired by the following drivers:
drivers/usb/typec/ucsi/ucsi_yoga_c630.c
drivers/usb/typec/ucsi/ucsi_glink.c
drivers/soc/qcom/pmic_glink_altmode.c
Signed-off-by: Pengyu Luo <mitltlatltl@gmail.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250316094357.462022-1-mitltlatltl@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To avoid using invalid USB device pointers after a Type-C partner
disconnects, this patch clears the pointers upon partner unregistration.
This ensures a clean state for future connections.
Cc: stable@vger.kernel.org
Fixes: 59de2a56d1 ("usb: typec: Link enumerated USB devices with Type-C partner")
Signed-off-by: Andrei Kuchynski <akuchynski@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Link: https://lore.kernel.org/r/20250321143728.4092417-3-akuchynski@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Concurrent calls to typec_partner_unlink_device can lead to a NULL pointer
dereference. This patch adds a mutex to protect USB device pointers and
prevent this issue. The same mutex protects both the device pointers and
the partner device registration.
Cc: stable@vger.kernel.org
Fixes: 59de2a56d1 ("usb: typec: Link enumerated USB devices with Type-C partner")
Signed-off-by: Andrei Kuchynski <akuchynski@chromium.org>
Reviewed-by: Benson Leung <bleung@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250321143728.4092417-2-akuchynski@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current xhci bus resume implementation prevents xHC host from generating
interrupts during high-speed USB 2 and super-speed USB 3 bus resume.
Only reason to disable interrupts during bus resume would be to prevent
the interrupt handler from interfering with the resume process of USB 2
ports.
Host initiated resume of USB 2 ports is done in two stages.
The xhci driver first transitions the port from 'U3' to 'Resume' state,
then wait in Resume for 20ms, and finally moves port to U0 state.
xhci driver can't prevent interrupts by keeping the xhci spinlock
due to this 20ms sleep.
Limit interrupt disabling to the USB 2 port resume case only.
resuming USB 2 ports in bus resume is only done in special cases where
USB 2 ports had to be forced to suspend during bus suspend.
The current way of preventing interrupts by clearing the 'Interrupt
Enable' (INTE) bit in USBCMD register won't prevent the Interrupter
registers 'Interrupt Pending' (IP), 'Event Handler Busy' (EHB) and
USBSTS register Event Interrupt (EINT) bits from being set.
New interrupts can't be issued before those bits are properly clered.
Disable interrupts by clearing the interrupter register 'Interrupt
Enable' (IE) bit instead. This way IP, EHB and INTE won't be set
before IE is enabled again and a new interrupt is triggered.
Reported-by: Devyn Liu <liudingyuan@huawei.com>
Closes: https://lore.kernel.org/linux-usb/b1a9e2d51b4d4ff7a304f77c5be8164e@huawei.com/
Cc: stable@vger.kernel.org
Tested-by: Devyn Liu <liudingyuan@huawei.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250410151828.2868740-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This check is performed before prepare_transfer() and prepare_ring(), so
enqueue can already point at the final link TRB of a segment. And indeed
it will, some 0.4% of times this code is called.
Then enqueue + 1 is an invalid pointer. It will crash the kernel right
away or load some junk which may look like a link TRB and cause the real
link TRB to be replaced with a NOOP. This wouldn't end well.
Use a functionally equivalent test which doesn't dereference the pointer
and always gives correct result.
Something has crashed my machine twice in recent days while playing with
an Etron HC, and a control transfer stress test ran for confirmation has
just crashed it again. The same test passes with this patch applied.
Fixes: 5e1c67abc9 ("xhci: Fix control transfer error on Etron xHCI host")
Cc: stable@vger.kernel.org
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reviewed-by: Kuangyi Chiang <ki.chiang65@gmail.com>
Link: https://lore.kernel.org/r/20250410151828.2868740-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A Short Packet event before the last TRB of a TD is followed by another
event on the final TRB on spec-compliant HCs, which is most of them.
A 'last_td_was_short' flag was added to know if a TD has just completed
as Short Packet and another event is to come. The flag was cleared after
seeing the event (unless no TDs are pending, but that's a separate bug)
or seeing a new TD complete as something other than Short Packet.
A rework replaced the flag with an 'old_trb_comp_code' variable. When
an event doesn't match the pending TD and the previous event was Short
Packet, the new event is silently ignored.
To preserve old behavior, 'old_trb_comp_code' should be cleared at this
point, but instead it is being set to current comp code, which is often
Short Packet again. This can cause more events to be silently ignored,
even though they are no longer connected with the old TD that completed
short and indicate a serious problem with the driver or the xHC.
Common device classes like UAC in async mode, UVC, serial or the UAS
status pipe complete as Short Packet routinely and could be affected.
Clear 'old_trb_comp_code' to zero, which is an invalid completion code
and the same value the variable starts with. This restores original
behavior on Short Packet and also works for illegal Etron events, which
the code has been extended to cover too.
Fixes: b331a3d809 ("xhci: Handle spurious events on Etron host isoc enpoints")
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250410151828.2868740-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allow for the DWC3 host driver to pass along XHCI property that defines
how many interrupters to allocate. This is in relation for the number of
event rings that can be potentially used by other processors within the
system.
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Tested-by: Puma Hsu <pumahsu@google.com>
Tested-by: Daehwan Jung <dh10.jung@samsung.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20250409194804.3773260-7-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the case of handling a USB bus reset, the xhci_discover_or_reset_device
can run without first notifying the xHCI sideband client driver to stop or
prevent the use of the transfer ring. It was seen that when a bus reset
situation happened, the USB offload driver was attempting to fetch the xHCI
transfer ring information, which was already freed.
Tested-by: Puma Hsu <pumahsu@google.com>
Tested-by: Daehwan Jung <dh10.jung@samsung.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20250409194804.3773260-6-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some platforms may want to limit the number of XHCI interrupters allocated.
This is passed to xhci-plat as a device property. Ensure that this is read
and the max_interrupters field is set.
Tested-by: Puma Hsu <pumahsu@google.com>
Tested-by: Daehwan Jung <dh10.jung@samsung.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20250409194804.3773260-5-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some clients may operate only on a specific XHCI interrupter instance.
Allow for the associated class driver to request for the interrupter that
it requires.
Tested-by: Puma Hsu <pumahsu@google.com>
Tested-by: Daehwan Jung <dh10.jung@samsung.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20250409194804.3773260-4-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As part of xHCI bus suspend, the xHCI is halted. However, if there are
pending events in the secondary event ring, it is observed that the xHCI
controller stops responding to further commands upon host or device
initiated bus resume. Iterate through all pending events and update the
dequeue pointer to the beginning of the event ring.
Tested-by: Puma Hsu <pumahsu@google.com>
Tested-by: Daehwan Jung <dh10.jung@samsung.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20250409194804.3773260-3-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce XHCI sideband, which manages the USB endpoints being requested by
a client driver. This is used for when client drivers are attempting to
offload USB endpoints to another entity for handling USB transfers. XHCI
sec intr will allow for drivers to fetch the required information about the
transfer ring, so the user can submit transfers independently. Expose the
required APIs for drivers to register and request for a USB endpoint and to
manage XHCI secondary interrupters.
Driver renaming, multiple ring segment page linking, proper endpoint clean
up, and allowing module compilation added by Wesley Cheng to complete
original concept code by Mathias Nyman.
Tested-by: Puma Hsu <pumahsu@google.com>
Tested-by: Daehwan Jung <dh10.jung@samsung.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Co-developed-by: Wesley Cheng <quic_wcheng@quicinc.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20250409194804.3773260-2-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since fwnode_get_child_node_count() was split from its device property
counterpart, we may utilise it in the driver and drop custom implementation.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Kyle Tso <kyletso@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20250310150835.3139322-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Lee Jones <lee@kernel.org>
timer_delete[_sync]() replaces del_timer[_sync](). Convert the whole tree
over and remove the historical wrapper inlines.
Conversion was done with coccinelle plus manual fixups where necessary.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Here is the big set of USB and Thunderbolt driver updates for 6.15-rc1.
Included in here are:
- Thunderbolt driver and core api updates for new hardware and
features
- usb-storage const array cleanups
- typec driver updates
- dwc3 driver updates
- xhci driver updates and bugfixes
- small USB documentation updates
- usb cdns3 driver updates
- usb gadget driver updates
- other small driver updates and fixes
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZ+2Zaw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynIgQCaAyMozdrZtTiOs1OcZEuTkoCtKrEAniqe0OiL
s7R6j2NoOIwo9d6hBsjh
=IH7I
-----END PGP SIGNATURE-----
Merge tag 'usb-6.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt driver updates for
6.15-rc1. Included in here are:
- Thunderbolt driver and core api updates for new hardware and
features
- usb-storage const array cleanups
- typec driver updates
- dwc3 driver updates
- xhci driver updates and bugfixes
- small USB documentation updates
- usb cdns3 driver updates
- usb gadget driver updates
- other small driver updates and fixes
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-6.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (92 commits)
thunderbolt: Do not add non-active NVM if NVM upgrade is disabled for retimer
thunderbolt: Scan retimers after device router has been enumerated
usb: host: cdns3: forward lost power information to xhci
usb: host: xhci-plat: allow upper layers to signal power loss
usb: xhci: change xhci_resume() parameters to explicit the desired info
usb: cdns3-ti: run HW init at resume() if HW was reset
usb: cdns3-ti: move reg writes to separate function
usb: cdns3: call cdns_power_is_lost() only once in cdns_resume()
usb: cdns3: rename hibernated argument of role->resume() to lost_power
usb: xhci: tegra: rename `runtime` boolean to `is_auto_runtime`
usb: host: xhci-plat: mvebu: use ->quirks instead of ->init_quirk() func
usb: dwc3: Don't use %pK through printk
usb: core: Don't use %pK through printk
usb: gadget: aspeed: Add NULL pointer check in ast_vhub_init_dev()
dt-bindings: usb: qcom,dwc3: Synchronize minItems for interrupts and -names
usb: common: usb-conn-gpio: switch psy_cfg from of_node to fwnode
usb: xhci: Avoid Stop Endpoint retry loop if the endpoint seems Running
usb: xhci: Don't change the status of stalled TDs on failed Stop EP
xhci: Avoid queuing redundant Stop Endpoint command for stalled endpoint
xhci: Handle spurious events on Etron host isoc enpoints
...
Updates to the usual drivers (scsi_debug, ufs, lpfc, st, fnic, mpi3mr,
mpt3sas) and the removal of cxlflash. The only non-trivial core change
is an addition to unit attention handling to recognize UAs for power
on/reset and new media so the tape driver can use it.
Signed-off-by: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCZ+RQ2yYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishe6DAQCdW/21
S1Y6BDlJLQfpWChGv6GIzanC+5sMfylw4d6ULgEA8upOE5L3fC29IY958jXig0o1
uLjxylwYEfVLDf8gwJ0=
=mkM+
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"Updates to the usual drivers (scsi_debug, ufs, lpfc, st, fnic, mpi3mr,
mpt3sas) and the removal of cxlflash.
The only non-trivial core change is an addition to unit attention
handling to recognize UAs for power on/reset and new media so the tape
driver can use it"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (107 commits)
scsi: st: Tighten the page format heuristics with MODE SELECT
scsi: st: ERASE does not change tape location
scsi: st: Fix array overflow in st_setup()
scsi: target: tcm_loop: Fix wrong abort tag
scsi: lpfc: Restore clearing of NLP_UNREG_INP in ndlp->nlp_flag
scsi: hisi_sas: Fixed failure to issue vendor specific commands
scsi: fnic: Remove unnecessary NUL-terminations
scsi: fnic: Remove redundant flush_workqueue() calls
scsi: core: Use a switch statement when attaching VPD pages
scsi: ufs: renesas: Add initialization code for R-Car S4-8 ES1.2
scsi: ufs: renesas: Add reusable functions
scsi: ufs: renesas: Refactor 0x10ad/0x10af PHY settings
scsi: ufs: renesas: Remove register control helper function
scsi: ufs: renesas: Add register read to remove save/set/restore
scsi: ufs: renesas: Replace init data by init code
scsi: ufs: dt-bindings: renesas,ufs: Add calibration data
scsi: mpi3mr: Task Abort EH Support
scsi: storvsc: Don't report the host packet status as the hv status
scsi: isci: Make most module parameters static
scsi: megaraid_sas: Make most module parameters static
...
hrtimers are initialized with hrtimer_init() and a subsequent store to
the callback pointer. This turned out to be suboptimal for the upcoming
Rust integration and is obviously a silly implementation to begin with.
This cleanup replaces the hrtimer_init(T); T->function = cb; sequence
with hrtimer_setup(T, cb);
The conversion was done with Coccinelle and a few manual fixups.
Once the conversion has completely landed in mainline, hrtimer_init()
will be removed and the hrtimer::function becomes a private member.
-----BEGIN PGP SIGNATURE-----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=bYAX
-----END PGP SIGNATURE-----
Merge tag 'timers-cleanups-2025-03-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer cleanups from Thomas Gleixner:
"A treewide hrtimer timer cleanup
hrtimers are initialized with hrtimer_init() and a subsequent store to
the callback pointer. This turned out to be suboptimal for the
upcoming Rust integration and is obviously a silly implementation to
begin with.
This cleanup replaces the hrtimer_init(T); T->function = cb; sequence
with hrtimer_setup(T, cb);
The conversion was done with Coccinelle and a few manual fixups.
Once the conversion has completely landed in mainline, hrtimer_init()
will be removed and the hrtimer::function becomes a private member"
* tag 'timers-cleanups-2025-03-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (100 commits)
wifi: rt2x00: Switch to use hrtimer_update_function()
io_uring: Use helper function hrtimer_update_function()
serial: xilinx_uartps: Use helper function hrtimer_update_function()
ASoC: fsl: imx-pcm-fiq: Switch to use hrtimer_setup()
RDMA: Switch to use hrtimer_setup()
virtio: mem: Switch to use hrtimer_setup()
drm/vmwgfx: Switch to use hrtimer_setup()
drm/xe/oa: Switch to use hrtimer_setup()
drm/vkms: Switch to use hrtimer_setup()
drm/msm: Switch to use hrtimer_setup()
drm/i915/request: Switch to use hrtimer_setup()
drm/i915/uncore: Switch to use hrtimer_setup()
drm/i915/pmu: Switch to use hrtimer_setup()
drm/i915/perf: Switch to use hrtimer_setup()
drm/i915/gvt: Switch to use hrtimer_setup()
drm/i915/huc: Switch to use hrtimer_setup()
drm/amdgpu: Switch to use hrtimer_setup()
stm class: heartbeat: Switch to use hrtimer_setup()
i2c: Switch to use hrtimer_setup()
iio: Switch to use hrtimer_setup()
...
Here's a single USB-serial cleanup for 6.15-rc1 that's been sitting in
linux-next for a few weeks without any reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCZ914qwAKCRALxc3C7H1l
CGD5AP9Dval6P27kP41zwKhk1gnFfcSQPXskkst+YSSTsD89bwD9FPuhf6M9ielL
4KgmSpY57sq8LFoerXOsrk09A79hew0=
=hLSA
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-6.15-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial update for 6.15-rc1
Here's a single USB-serial cleanup for 6.15-rc1 that's been sitting in
linux-next for a few weeks without any reported issues.
* tag 'usb-serial-6.15-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: mos7840: drop unused defines
cdns3-plat can know if power was lost across system-wide suspend.
Forward that information:
- Grab the lost_power bool from cdns_role_driver::resume(). Store it
into the power_lost field in struct xhci_plat_priv.
- xhci-plat will call xhci_resume() with that value (ORed to whether we
are in a hibernation restore).
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20250205-s2r-cdns-v7-9-13658a271c3c@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that xhci_resume() exposes a power_lost boolean argument, expose
that to all xhci-plat implementations. They are free to set it from
wherever they want:
- Their own resume() callback.
- The xhci_plat_priv::resume_quirk() callback.
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20250205-s2r-cdns-v7-8-13658a271c3c@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previous signature was:
int xhci_resume(struct xhci_hcd *xhci, pm_message_t msg);
Internally, it extracted two information out of the message:
- whether we are after hibernation: msg.event == PM_EVENT_RESTORE,
- whether this is an auto resume: msg.event == PM_EVENT_AUTO_RESUME.
First bulletpoint is somewhat wrong: driver wants to know if the device
did lose power, it doesn't care about hibernation per se. Knowing that,
refactor to ask upper layers the right questions: (1) "did we lose
power?" and, (2) "is this an auto resume?". Change the signature to:
int xhci_resume(struct xhci_hcd *xhci, bool power_lost,
bool is_auto_resume);
The goal is to allow some upper layers (cdns3-plat) to tell us when
power was lost after system-wise suspend.
Note that lost_power is ORed at the start of xhci_resume() to
xhci->quirks & XHCI_RESET_ON_RESUME || xhci->broken_suspend. It is
simpler to keep those checks inside of xhci_resume() instead of doing
them at each caller of xhci_resume().
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20250205-s2r-cdns-v7-7-13658a271c3c@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At runtime_resume(), read the W1 (Wrapper Register 1) register to detect
if an hardware reset occurred. If it did, run the hardware init sequence.
This callback will be called at system-wide resume. Previously, if a
reset occurred during suspend, we would crash. The wrapper config had
not been written, leading to invalid register accesses inside cdns3.
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20250205-s2r-cdns-v7-6-13658a271c3c@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The device probe function mixes management code and hardware
initialisation code. Extract the latter into an explicitly named
cdns_ti_reset_and_init_hw() function to clarify intent. It also will
allow easier transition to using runtime PM for triggering HW init.
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20250205-s2r-cdns-v7-5-13658a271c3c@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The cdns_role_driver->resume() callback takes a second boolean argument
named `hibernated` in its implementations. This is mistaken; the only
potential caller is:
int cdns_resume(struct cdns *cdns)
{
/* ... */
if (cdns->roles[cdns->role]->resume)
cdns->roles[cdns->role]->resume(cdns, cdns_power_is_lost(cdns));
return 0;
}
The argument can be true in cases outside of return from hibernation.
Reflect the true meaning by renaming both arguments to `lost_power`.
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20250205-s2r-cdns-v7-3-13658a271c3c@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unify naming convention: use `is_auto_runtime` in xhci-tegra, to be in
phase with (future) drivers/usb/host/xhci.c.
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20250205-s2r-cdns-v7-2-13658a271c3c@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Compatible "marvell,armada3700-xhci" match data uses the
struct xhci_plat_priv::init_quirk() function pointer to add
XHCI_RESET_ON_RESUME as quirk on XHCI.
Instead, use the struct xhci_plat_priv::quirks field.
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20250205-s2r-cdns-v7-1-13658a271c3c@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a revert of
commit 04fb365c45 ("usb: dwc3: replace %p with %pK")
When the formatting was changed from %p to %pK that was a security
improvement, as %p would leak raw pointer values to the kernel log.
Since commit ad67b74d24 ("printk: hash addresses printed with %p")
the regular %p has been improved to avoid this issue.
On the other hand, restricted pointers ("%pK") were never meant to be used
through printk(). They can unintentionally still leak raw pointers or
acquire sleeping looks in atomic contexts.
Switch back to regular %p again.
Link: https://lore.kernel.org/lkml/20250113171731-dc10e3c1-da64-4af0-b767-7c7070468023@linutronix.de/
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Link: https://lore.kernel.org/r/20250310-restricted-pointers-usb-v2-2-a7598e2d47d1@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a revert of
commit 2f964780c0 ("USB: core: replace %p with %pK").
When the formatting was changed from %p to %pK that was a security
improvement, as %p would leak raw pointer values to the kernel log.
Since commit ad67b74d24 ("printk: hash addresses printed with %p")
the regular %p has been improved to avoid this issue.
On the other hand, restricted pointers ("%pK") were never meant to be used
through printk(). They can unintentionally still leak raw pointers or
acquire sleeping looks in atomic contexts.
Switch back to regular %p again.
Link: https://lore.kernel.org/lkml/20250113171731-dc10e3c1-da64-4af0-b767-7c7070468023@linutronix.de/
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Link: https://lore.kernel.org/r/20250310-restricted-pointers-usb-v2-1-a7598e2d47d1@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The variable d->name, returned by devm_kasprintf(), could be NULL.
A pointer check is added to prevent potential NULL pointer dereference.
This is similar to the fix in commit 3027e7b15b
("ice: Fix some null pointer dereference issues in ice_ptp.c").
This issue is found by our static analysis tool
Signed-off-by: Chenyuan Yang <chenyuan0y@gmail.com>
Link: https://lore.kernel.org/r/20250311012705.1233829-1-chenyuan0y@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A subtle error got introduced while manually fixing merge conflict in
tcpm.c for commit 85c4efbe60 ("Merge v6.12-rc6 into usb-next"). As a
result of this error, the next state is unconditionally set to
SNK_WAIT_CAPABILITIES_TIMEOUT while handling SNK_WAIT_CAPABILITIES state
in run_state_machine(...).
Fix this by setting new state of TCPM state machine to `upcoming_state`
(that is set to different values based on conditions).
Cc: stable@vger.kernel.org
Fixes: 85c4efbe60 ("Merge v6.12-rc6 into usb-next")
Signed-off-by: Amit Sunil Dhamne <amitsd@google.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250310-fix-snk-wait-timeout-v6-14-rc6-v1-1-5db14475798f@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some new modem device ids and a couple of related fixes, and
support for Altera USB Blaster 3.
All have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCZ9PWawAKCRALxc3C7H1l
CKveAP9oScoe3RLTX9S+X+tcIree4W0EY1vK2iQX3iKxPi1R4wEAl87YJJRj1HvG
O7U369iyzLgH4LrZBlOOhWVVJ6TA4ws=
=jpq3
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-6.14-rc7' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial device ids for 6.14-rc7
Here are some new modem device ids and a couple of related fixes, and
support for Altera USB Blaster 3.
All have been in linux-next with no reported issues.
* tag 'usb-serial-6.14-rc7' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: ftdi_sio: add support for Altera USB Blaster 3
USB: serial: option: fix Telit Cinterion FE990A name
USB: serial: option: add Telit Cinterion FE990B compositions
USB: serial: option: match on interface class for Telit FN990B
The Altera USB Blaster 3, available as both a cable and an on-board
solution, is primarily used for programming and debugging FPGAs.
It interfaces with host software such as Quartus Programmer,
System Console, SignalTap, and Nios Debugger. The device utilizes
either an FT2232 or FT4232 chip.
Enabling the support for various configurations of the on-board
USB Blaster 3 by including the appropriate VID/PID pairs,
allowing it to function as a serial device via ftdi_sio.
Note that this check-in does not include support for the
cable solution, as it does not support UART functionality.
The supported configurations are determined by the
hardware design and include:
1) PID 0x6022, FT2232, 1 JTAG port (Port A) + Port B as UART
2) PID 0x6025, FT4232, 1 JTAG port (Port A) + Port C as UART
3) PID 0x6026, FT4232, 1 JTAG port (Port A) + Port C, D as UART
4) PID 0x6029, FT4232, 1 JTAG port (Port B) + Port C as UART
5) PID 0x602a, FT4232, 1 JTAG port (Port B) + Port C, D as UART
6) PID 0x602c, FT4232, 1 JTAG port (Port A) + Port B as UART
7) PID 0x602d, FT4232, 1 JTAG port (Port A) + Port B, C as UART
8) PID 0x602e, FT4232, 1 JTAG port (Port A) + Port B, C, D as UART
These configurations allow for flexibility in how the USB Blaster 3 is
used, depending on the specific needs of the hardware design.
Signed-off-by: Boon Khai Ng <boon.khai.ng@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Nothing prevents a broken HC from claiming that an endpoint is Running
and repeatedly rejecting Stop Endpoint with Context State Error.
Avoid infinite retries and give back cancelled TDs.
No such cases known so far, but HCs have bugs.
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250311154551.4035726-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the device stalls an endpoint, current TD is assigned -EPIPE
status and Reset Endpoint is queued. If a Stop Endpoint is pending
at the time, it will run before Reset Endpoint and fail due to the
stall. Its handler will change TD's status to -EPROTO before Reset
Endpoint handler runs and initiates giveback.
Check if the stall has already been handled and don't try to do it
again. Since xhci_handle_halted_endpoint() performs this check too,
not overwriting td->status is the only difference.
I haven't seen this case yet, but I have seen a related one where
the xHC has already executed Reset Endpoint, EP Context state is
now Stopped and EP_HALTED is set. If the xHC took a bit longer to
execute Reset Endpoint, said case would become this one.
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250311154551.4035726-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If EP_STALLED flag is set in xhci_urb_dequeue(), without EP_HALTED or
SET_DEQ_PENDING flags, then the endpoint is in stopped state and the
cancelled URB can be given back immediately withouth queueing
a 'stop endpoint' command.
Without this change the cancelled URB would eventually be given back
in the 'context state error' completion path of the 'stop endpoint'
command. This is not optimal.
For this improvement to work the EP_STALLED flag must be cleared with
xhci lock held.
Suggested-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250311154551.4035726-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Resources should be released only after all threads that utilize them
have been destroyed.
This commit ensures that resources are not released prematurely by waiting
for the associated workqueue to complete before deallocating them.
Cc: stable <stable@kernel.org>
Fixes: b9aa02ca39 ("usb: typec: ucsi: Add polling mechanism for partner tasks like alt mode checking")
Signed-off-by: Andrei Kuchynski <akuchynski@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250305111739.1489003-2-akuchynski@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When used on Huawei hisi platforms, Prolific Mass Storage Card Reader
which the VID:PID is in 067b:2731 might fail to enumerate at boot time
and doesn't work well with LPM enabled, combination quirks:
USB_QUIRK_DELAY_INIT + USB_QUIRK_NO_LPM
fixed the problems.
Signed-off-by: Miao Li <limiao@kylinos.cn>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20250304070757.139473-1-limiao870622@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unplugging a USB3.0 webcam from Etron hosts while streaming results
in errors like this:
[ 2.646387] xhci_hcd 0000:03:00.0: ERROR Transfer event TRB DMA ptr not part of current TD ep_index 18 comp_code 13
[ 2.646446] xhci_hcd 0000:03:00.0: Looking for event-dma 000000002fdf8630 trb-start 000000002fdf8640 trb-end 000000002fdf8650
[ 2.646560] xhci_hcd 0000:03:00.0: ERROR Transfer event TRB DMA ptr not part of current TD ep_index 18 comp_code 13
[ 2.646568] xhci_hcd 0000:03:00.0: Looking for event-dma 000000002fdf8660 trb-start 000000002fdf8670 trb-end 000000002fdf8670
Etron xHC generates two transfer events for the TRB if an error is
detected while processing the last TRB of an isoc TD.
The first event can be any sort of error (like USB Transaction or
Babble Detected, etc), and the final event is Success.
The xHCI driver will handle the TD after the first event and remove it
from its internal list, and then print an "Transfer event TRB DMA ptr
not part of current TD" error message after the final event.
Commit 5372c65e13 ("xhci: process isoc TD properly when there was a
transaction error mid TD.") is designed to address isoc transaction
errors, but unfortunately it doesn't account for this scenario.
This issue is similar to the XHCI_SPURIOUS_SUCCESS case where a success
event follows a 'short transfer' event, but the TD the event points to
is already given back.
Expand the spurious success 'short transfer' event handling to cover
the spurious success after error on Etron hosts.
Kuangyi Chiang reported this issue and submitted a different solution
based on using error_mid_td. This commit message is mostly taken
from that patch.
Reported-by: Kuangyi Chiang <ki.chiang65@gmail.com>
Closes: https://lore.kernel.org/linux-usb/20241028025337.6372-6-ki.chiang65@gmail.com/
Tested-by: Kuangyi Chiang <ki.chiang65@gmail.com>
Tested-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250306144954.3507700-16-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Extract a block of code copied from inc_enq() into a separate function
and call it from inc_enq() and the other function which used this code.
Remove the pointless 'next' variable which only aliases ring->enqueue.
Note: I don't know if any 0.95 xHC ever reached series production, but
"AMD 0.96 host" appears to be the "Llano" family APU. Example dmesg at
https://linux-hardware.org/?probe=79d5cfd4fd&log=dmesg
pci 0000:00:10.0: [1022:7812] type 00 class 0x0c0330
hcc params 0x014042c3 hci version 0x96 quirks 0x0000000000000608
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250306144954.3507700-15-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Two clearly different specimens of NEC uPD720200 (one with start/stop
bug, one without) were seen to cause IOMMU faults after some Missed
Service Errors. Faulting address is immediately after a transfer ring
segment and patched dynamic debug messages revealed that the MSE was
received when waiting for a TD near the end of that segment:
[ 1.041954] xhci_hcd: Miss service interval error for slot 1 ep 2 expected TD DMA ffa08fe0
[ 1.042120] xhci_hcd: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0005 address=0xffa09000 flags=0x0000]
[ 1.042146] xhci_hcd: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0005 address=0xffa09040 flags=0x0000]
It gets even funnier if the next page is a ring segment accessible to
the HC. Below, it reports MSE in segment at ff1e8000, plows through a
zero-filled page at ff1e9000 and starts reporting events for TRBs in
page at ff1ea000 every microframe, instead of jumping to seg ff1e6000.
[ 7.041671] xhci_hcd: Miss service interval error for slot 1 ep 2 expected TD DMA ff1e8fe0
[ 7.041999] xhci_hcd: Miss service interval error for slot 1 ep 2 expected TD DMA ff1e8fe0
[ 7.042011] xhci_hcd: WARN: buffer overrun event for slot 1 ep 2 on endpoint
[ 7.042028] xhci_hcd: All TDs skipped for slot 1 ep 2. Clear skip flag.
[ 7.042134] xhci_hcd: WARN: buffer overrun event for slot 1 ep 2 on endpoint
[ 7.042138] xhci_hcd: ERROR Transfer event TRB DMA ptr not part of current TD ep_index 2 comp_code 31
[ 7.042144] xhci_hcd: Looking for event-dma 00000000ff1ea040 trb-start 00000000ff1e6820 trb-end 00000000ff1e6820
[ 7.042259] xhci_hcd: WARN: buffer overrun event for slot 1 ep 2 on endpoint
[ 7.042262] xhci_hcd: ERROR Transfer event TRB DMA ptr not part of current TD ep_index 2 comp_code 31
[ 7.042266] xhci_hcd: Looking for event-dma 00000000ff1ea050 trb-start 00000000ff1e6820 trb-end 00000000ff1e6820
At some point completion events change from Isoch Buffer Overrun to
Short Packet and the HC finally finds cycle bit mismatch in ff1ec000.
[ 7.098130] xhci_hcd: ERROR Transfer event TRB DMA ptr not part of current TD ep_index 2 comp_code 13
[ 7.098132] xhci_hcd: Looking for event-dma 00000000ff1ecc50 trb-start 00000000ff1e6820 trb-end 00000000ff1e6820
[ 7.098254] xhci_hcd: ERROR Transfer event TRB DMA ptr not part of current TD ep_index 2 comp_code 13
[ 7.098256] xhci_hcd: Looking for event-dma 00000000ff1ecc60 trb-start 00000000ff1e6820 trb-end 00000000ff1e6820
[ 7.098379] xhci_hcd: Overrun event on slot 1 ep 2
It's possible that data from the isochronous device were written to
random buffers of pending TDs on other endpoints (either IN or OUT),
other devices or even other HCs in the same IOMMU domain.
Lastly, an error from a different USB device on another HC. Was it
caused by the above? I don't know, but it may have been. The disk
was working without any other issues and generated PCIe traffic to
starve the NEC of upstream BW and trigger those MSEs. The two HCs
shared one x1 slot by means of a commercial "PCIe splitter" board.
[ 7.162604] usb 10-2: reset SuperSpeed USB device number 3 using xhci_hcd
[ 7.178990] sd 9:0:0:0: [sdb] tag#0 UNKNOWN(0x2003) Result: hostbyte=0x07 driverbyte=DRIVER_OK cmd_age=0s
[ 7.179001] sd 9:0:0:0: [sdb] tag#0 CDB: opcode=0x28 28 00 04 02 ae 00 00 02 00 00
[ 7.179004] I/O error, dev sdb, sector 67284480 op 0x0:(READ) flags 0x80700 phys_seg 5 prio class 0
Fortunately, it appears that this ridiculous bug is avoided by setting
the chain bit of Link TRBs on isochronous rings. Other ancient HCs are
known which also expect the bit to be set and they ignore Link TRBs if
it's not. Reportedly, 0.95 spec guaranteed that the bit is set.
The bandwidth-starved NEC HC running a 32KB/uframe UVC endpoint reports
tens of MSEs per second and runs into the bug within seconds. Chaining
Link TRBs allows the same workload to run for many minutes, many times.
No negative side effects seen in UVC recording and UAC playback with a
few devices at full speed, high speed and SuperSpeed.
The problem doesn't reproduce on the newer Renesas uPD720201/uPD720202
and on old Etron EJ168 and VIA VL805 (but the VL805 has other bug).
[shorten line length of log snippets in commit messge -Mathias]
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250306144954.3507700-14-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ensure that an endpoint halted due to device STALL is not
restarted before a Clear_Feature(ENDPOINT_HALT) request is sent to
the device.
The host side of the endpoint may otherwise be started early by the
'Set TR Deq' command completion handler which is called if dequeue
is moved past a cancelled or halted TD.
Prevent this with a new flag set for bulk and interrupt endpoints
when a Stall Error is received. Clear it in hcd->endpoint_reset()
which is called after Clear_Feature(ENDPOINT_HALT) is sent.
Also add a debug message if a class driver queues a new URB after the
STALL. Note that class driver might not be aware of the STALL
yet when it submits the URB as URBs are given back in BH.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250306144954.3507700-13-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Function trb_in_td() currently includes debug capabilities that are
triggered when its debug argument is set to true. The only consumer of
these debug capabilities is handle_tx_event(), which calls trb_in_td()
twice, once for its primary functionality and a second time solely for
debugging purposes if the first call returns 'NULL'.
This approach is inefficient and can lead to confusion, as trb_in_td()
executes the same code with identical arguments twice, differing only in
the debug output during the second execution.
To enhance clarity and efficiency, move the debug capabilities out of
trb_in_td() and integrates them directly into handle_tx_event().
This change reduces the argument count of trb_in_td() and ensures that
debug steps are executed only when necessary, streamlining the function's
operation.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250306144954.3507700-12-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Relocate trb_in_td() and marks it as static, as it's exclusively utilized
in xhci-ring.c. This adjustment lays the groundwork for future rework of
the function.
The function's logic remains unchanged; only its access specifier is
altered to static and a redundant "else" is removed on line 325
(due to checkpatch.pl complaining).
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250306144954.3507700-11-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current xHCI driver does not validate whether a page size of 4096
bytes is supported. Address the issue by setting the page size to the
value supported by the xHCI controller, as read from the Page Size
register. In the event of an unexpected value; default to a 4K page size.
Additionally, this commit removes unnecessary debug messages and instead
prints the supported and used page size once.
The xHCI controller supports page sizes of (2^{(n+12)}) bytes, where 'n'
is the Page Size Bit. Only one page size is supported, with a maximum
page size of 128 KB.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250306144954.3507700-10-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ffs() function returns the index of the first set bit, starting from 1.
If no bits are set, it returns zero. This behavior causes an off-by-one
page size in the debug message, as the page size calculation [1]
is zero-based, while ffs() is one-based.
Fix this by subtracting one from the result of ffs(). Note that since
variable 'val' is unsigned, subtracting one from zero will result in the
maximum unsigned integer value. Consequently, the condition 'if (val < 16)'
will still function correctly.
[1], Page size: (2^(n+12)), where 'n' is the set page size bit.
Fixes: 81720ec532 ("usb: host: xhci: use ffs() in xhci_mem_init()")
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250306144954.3507700-9-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If skipping is deferred to events other than Missed Service Error itsef,
it means we are running on an xHCI 1.0 host and don't know how many TDs
were missed until we reach some ordinary transfer completion event.
And in case of ring xrun, we can't know where the xrun happened either.
If we skip all pending TDs, we may prematurely give back TDs added after
the xrun had occurred, risking data loss or buffer UAF by the xHC.
If we skip none, a driver may become confused and stop working when all
its URBs are missed and appear to be "in flight" forever.
Skip exactly one TD on each xrun event - the first one that was missed,
as we can now be sure that the HC has finished processing it. Provided
that one more TD is queued before any subsequent doorbell ring, it will
become safe to skip another TD by the time we get an xrun again.
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250306144954.3507700-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xHCI spec rev. 1.0 allowed the TRB pointer of Missed Service events
to be NULL. Having no idea which of the queued TDs were missed and
which are waiting, we can only set a flag to skip missed TDs later.
But HCs are also allowed to give us pointer to the last missed TRB,
and this became mandatory in spec rev. 1.1 and later.
Use this pointer, if available, to immediately skip all missed TDs.
This reduces latency and risk of skipping-related bugs, because we
can now leave the skip flag cleared for future events.
Handle Missed Service Error events as 'error mid TD', if applicable,
because rev. 1.0 spec excplicitly says so in notes to 4.10.3.2 and
later revs in 4.10.3.2 and 4.11.2.5.2. Notes to 4.9.1 seem to apply.
Tested on ASM1142 and ASM3142 v1.1 xHCs which provide TRB pointers.
Tested on AMD, Etron, Renesas v1.0 xHCs which provide TRB pointers.
Tested on NEC v0.96 and VIA v1.0 xHCs which send a NULL pointer.
Change inspired by a discussion about realtime USB audio.
Link: https://lore.kernel.org/linux-usb/76e1a191-020d-4a76-97f6-237f9bd0ede0@gmx.net/T/
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250306144954.3507700-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TRB pointer of these events points at enqueue at the time of error
occurrence on xHCI 1.1+ HCs or it's NULL on older ones. By the time we
are handling the event, a new TD may be queued at this ring position.
I can trigger this race by rising interrupt moderation to increase IRQ
handling delay. Similar delay may occur naturally due to system load.
If this ever happens after a Missed Service Error, missed TDs will be
skipped and the new TD processed as if it matched the event. It could
be given back prematurely, risking data loss or buffer UAF by the xHC.
Don't complete TDs on xrun events and don't warn if queued TDs don't
match the event's TRB pointer, which can be NULL or a link/no-op TRB.
Don't warn if there are no queued TDs at all.
Now that it's safe, also handle xrun events if the skip flag is clear.
This ensures completion of any TD stuck in 'error mid TD' state right
before the xrun event, which could happen if a driver submits a finite
number of URBs to a buggy HC and then an error occurs on the last TD.
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250306144954.3507700-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Missed Service Error after an error mid TD means that the failed TD has
already been passed by the xHC without acknowledgment of the final TRB,
a known hardware bug. So don't wait any more and give back the TD.
Reproduced on NEC uPD720200 under conditions of ludicrously bad USB link
quality, confirmed to behave as expected using dynamic debug.
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250306144954.3507700-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Up until commit d56b0b2ab1 ("usb: xhci: ensure skipped isoc TDs are
returned when isoc ring is stopped") in v6.11, the driver didn't skip
missed isochronous TDs when handling Stoppend and Stopped - Length
Invalid events. Instead, it erroneously cleared the skip flag, which
would cause the ring to get stuck, as future events won't match the
missed TD which is never removed from the queue until it's cancelled.
This buggy logic seems to have been in place substantially unchanged
since the 3.x series over 10 years ago, which probably speaks first
and foremost about relative rarity of this case in normal usage, but
by the spec I see no reason why it shouldn't be possible.
After d56b0b2ab1, TDs are immediately skipped when handling those
Stopped events. This poses a potential problem in case of Stopped -
Length Invalid, which occurs either on completed TDs (likely already
given back) or Link and No-Op TRBs. Such event won't be recognized
as matching any TD (unless it's the rare Link TRB inside a TD) and
will result in skipping all pending TDs, giving them back possibly
before they are done, risking isoc data loss and maybe UAF by HW.
As a compromise, don't skip and don't clear the skip flag on this
kind of event. Then the next event will skip missed TDs. A downside
of not handling Stopped - Length Invalid on a Link inside a TD is
that if the TD is cancelled, its actual length will not be updated
to account for TRBs (silently) completed before the TD was stopped.
I had no luck producing this sequence of completion events so there
is no compelling demonstration of any resulting disaster. It may be
a very rare, obscure condition. The sole motivation for this patch
is that if such unlikely event does occur, I'd rather risk reporting
a cancelled partially done isoc frame as empty than gamble with UAF.
This will be fixed more properly by looking at Stopped event's TRB
pointer when making skipping decisions, but such rework is unlikely
to be backported to v6.12, which will stay around for a few years.
Fixes: d56b0b2ab1 ("usb: xhci: ensure skipped isoc TDs are returned when isoc ring is stopped")
Cc: stable@vger.kernel.org
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250306144954.3507700-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function is a remnant from a previous implementation and is now
redundant. There is no longer a need to search for the dequeue pointer,
as both the TRB and segment dequeue pointers are saved within
'queued_deq_seg' and 'queued_deq_ptr'.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250306144954.3507700-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
U2 value is encoded in 256 microsecond intervals, show in microseconds.
U1 value is in microseconds. debug message incorrectly showed "ms"
Unwrap debug messages while we anyway modify them.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250306144954.3507700-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The correct name for FE990 is FE990A so use it in order to avoid
confusion with FE990B.
Cc: stable@vger.kernel.org
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
The device id entries for Telit FN990B ended up matching only on the
interface protocol. While this works, the protocol is qualified by the
interface class (and subclass) which should have been included.
Switch to matching using USB_DEVICE_AND_INTERFACE_INFO() while keeping
the entries sorted also by protocol for consistency.
Link: https://lore.kernel.org/20250227110655.3647028-2-fabio.porcedda@gmail.com/
Cc: Fabio Porcedda <fabio.porcedda@gmail.com>
Cc: Daniele Palmas <dnlplm@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
A recent cleanup went a bit too far and dropped clearing the cycle bit
of link TRBs, so it stays different from the rest of the ring half of
the time. Then a race occurs: if the xHC reaches such link TRB before
more commands are queued, the link's cycle bit unintentionally matches
the xHC's cycle so it follows the link and waits for further commands.
If more commands are queued before the xHC gets there, inc_enq() flips
the bit so the xHC later sees a mismatch and stops executing commands.
This function is called before suspend and 50% of times after resuming
the xHC is doomed to get stuck sooner or later. Then some Stop Endpoint
command fails to complete in 5 seconds and this shows up
xhci_hcd 0000:00:10.0: xHCI host not responding to stop endpoint command
xhci_hcd 0000:00:10.0: xHCI host controller not responding, assume dead
xhci_hcd 0000:00:10.0: HC died; cleaning up
followed by loss of all USB decives on the affected bus. That's if you
are lucky, because if Set Deq gets stuck instead, the failure is silent.
Likely responsible for kernel bug 219824. I found this while searching
for possible causes of that regression and reproduced it locally before
hearing back from the reporter. To repro, simply wait for link cycle to
become set (debugfs), then suspend, resume and wait. To accelerate the
failure I used a script which repeatedly starts and stops a UVC camera.
Some HCs get fully reinitialized on resume and they are not affected.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=219824
Fixes: 36b972d4b7 ("usb: xhci: improve xhci_clear_command_ring()")
Cc: stable@vger.kernel.org
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250304113147.3322584-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After phy initialization, some phy operations can only be executed while
in lower P states. Ensure GUSB3PIPECTL.SUSPENDENABLE and
GUSB2PHYCFG.SUSPHY are set soon after initialization to avoid blocking
phy ops.
Previously the SUSPENDENABLE bits are only set after the controller
initialization, which may not happen right away if there's no gadget
driver or xhci driver bound. Revise this to clear SUSPENDENABLE bits
only when there's mode switching (change in GCTL.PRTCAPDIR).
Fixes: 6d73572206 ("usb: dwc3: core: Prevent phy suspend during init")
Cc: stable <stable@kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/633aef0afee7d56d2316f7cc3e1b2a6d518a8cc9.1738280911.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Exynos7870 devices have a DWC3 compatible USB 2.0 controller.
Add support in the driver by:
- Adding its own compatible string, "samsung,exynos7870-dwusb3".
- Adding three USBDRD clocks named "bus_early", "ref", and "ctrl", to
be controlled by the driver.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250301-exynos7870-usb-v3-2-f01697165d19@disroot.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This array is only read, not modified.
Declaring data as const makes it easier to see what's going on, and can
prevent unintended writes through placement in a read-only section.
Signed-off-by: Jonathan Neuschäfer <j.ne@posteo.net>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20250228-misc-const-v3-9-09b417ded9c4@posteo.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These arrays are only read, not modified.
Declaring data as const makes it easier to see what's going on, and can
prevent unintended writes through placement in a read-only section.
Signed-off-by: Jonathan Neuschäfer <j.ne@posteo.net>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20250228-misc-const-v3-8-09b417ded9c4@posteo.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The nand_flash_ids, inquiry_response, and mode_page_01 arrays are only
read, not modified.
Declaring data as const makes it easier to see what's going on, and can
prevent unintended writes through placement in a read-only section.
Signed-off-by: Jonathan Neuschäfer <j.ne@posteo.net>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20250228-misc-const-v3-7-09b417ded9c4@posteo.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These arrays are only read, never modified.
Declaring data as const makes it easier to see what's going on, and can
prevent unintended writes through placement in a read-only section.
Signed-off-by: Jonathan Neuschäfer <j.ne@posteo.net>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20250228-misc-const-v3-6-09b417ded9c4@posteo.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
init_string is only read, not modified.
Declaring data as const makes it easier to see what's going on, and can
prevent unintended writes through placement in a read-only section.
Signed-off-by: Jonathan Neuschäfer <j.ne@posteo.net>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20250228-misc-const-v3-5-09b417ded9c4@posteo.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These arrays are only read, not modified.
Declaring data as const makes it easier to see what's going on, and can
prevent unintended writes through placement in a read-only section.
Signed-off-by: Jonathan Neuschäfer <j.ne@posteo.net>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20250228-misc-const-v3-4-09b417ded9c4@posteo.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The alauda_card_ids array is only read, and not modified.
Declaring data as const makes it easier to see what's going on, and can
prevent unintended writes through placement in a read-only section.
Signed-off-by: Jonathan Neuschäfer <j.ne@posteo.net>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20250228-misc-const-v3-3-09b417ded9c4@posteo.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This array is only read, not modified.
Declaring data as const makes it easier to see what's going on, and can
prevent unintended writes through placement in a read-only section.
Signed-off-by: Jonathan Neuschäfer <j.ne@posteo.net>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20250228-misc-const-v3-2-09b417ded9c4@posteo.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These arrays are not modified. Make them const.
Declaring data as const makes it easier to see what's going on, and can
prevent unintended writes through placement in a read-only section.
Signed-off-by: Jonathan Neuschäfer <j.ne@posteo.net>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20250228-misc-const-v3-1-09b417ded9c4@posteo.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If no fw_build is recognized for the controller there is no point to
exposing the `do_flash` attribute.
Add an is_visible callback to the attribute group and check for that
fw_build member to hide when not applicable.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250221054137.1631765-3-superm1@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The error `failed to get FW build information` is added for what looks
to be for misdetection of the device property firmware-name.
If the property is missing (such as on non-nvidia HW) this error shows up.
Move the error into the scope of the property parser for "firmware-name"
to avoid showing errors on systems without the firmware-name property.
Fixes: 5c9ae5a875 ("usb: typec: ucsi: ccg: add firmware flashing support")
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250221054137.1631765-2-superm1@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
otg_ulpi_create() has been unused since 2022's
commit 8ca79aaad8 ("ARM: pxa: remove unused pxa3xx-ulpi")
Remove it.
The devm_ variant is still used.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Link: https://lore.kernel.org/r/20250223160602.91916-1-linux@treblig.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb_sndaddr0pipe macro is only used in the hub_set_address function.
Replace it with usb_sndctrlpipe which provides the same functionality
but would also consider the endpoint device number.
If the device has not been initialised, it is safe to use
usb_sndctrlpipe in this context because udev->devnum is set to 0.
Therefore, this change does not affect behaviour, but reduces code
complexity by reusing the existing macro.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20250219083745.10406-1-eichest@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xHC resources allocated for USB devices are not released in correct
order after resuming in case when while suspend device was reconnected.
This issue has been detected during the fallowing scenario:
- connect hub HS to root port
- connect LS/FS device to hub port
- wait for enumeration to finish
- force host to suspend
- reconnect hub attached to root port
- wake host
For this scenario during enumeration of USB LS/FS device the Cadence xHC
reports completion error code for xHC commands because the xHC resources
used for devices has not been properly released.
XHCI specification doesn't mention that device can be reset in any order
so, we should not treat this issue as Cadence xHC controller bug.
Similar as during disconnecting in this case the device resources should
be cleared starting form the last usb device in tree toward the root hub.
To fix this issue usbcore driver should call hcd->driver->reset_device
for all USB devices connected to hub which was reconnected while
suspending.
Fixes: 3d82904559 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/PH7PR07MB953841E38C088678ACDCF6EEDDCC2@PH7PR07MB9538.namprd07.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When performing continuous unbind/bind operations on the USB drivers
available on the Renesas RZ/G2L SoC, a kernel crash with the message
"Unable to handle kernel NULL pointer dereference at virtual address"
may occur. This issue points to the usbhsc_notify_hotplug() function.
Flush the delayed work to avoid its execution when driver resources are
unavailable.
Fixes: bc57381e63 ("usb: renesas_usbhs: use delayed_work instead of work_struct")
Cc: stable <stable@kernel.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20250225110248.870417-4-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The gpriv->transceiver is retrieved in probe() through usb_get_phy() but
never released. Use devm_usb_get_phy() to handle this scenario.
This issue was identified through code investigation. No issue was found
without this change.
Fixes: b5a2875605 ("usb: renesas_usbhs: Allow an OTG PHY driver to provide VBUS")
Cc: stable <stable@kernel.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20250225110248.870417-3-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the USB configuration is not valid, then avoid checking for
bmAttributes to prevent null pointer deference.
Cc: stable <stable@kernel.org>
Fixes: 40e89ff575 ("usb: gadget: Set self-powered based on MaxPower and bmAttributes")
Signed-off-by: Prashanth K <prashanth.k@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250224085604.417327-1-prashanth.k@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When adding support for USB3-over-USB4 tunnelling detection, a check
for an Intel-specific capability was added. This capability, which
goes by ID 206, is used without any check that we are actually
dealing with an Intel host.
As it turns out, the Cadence XHCI controller *also* exposes an
extended capability numbered 206 (for unknown purposes), but of
course doesn't have the Intel-specific registers that the tunnelling
code is trying to access. Fun follows.
The core of the problems is that the tunnelling code blindly uses
vendor-specific capabilities without any check (the Intel-provided
documentation I have at hand indicates that 192-255 are indeed
vendor-specific).
Restrict the detection code to Intel HW for real, preventing any
further explosion on my (non-Intel) HW.
Cc: stable <stable@kernel.org>
Fixes: 948ce83fbb ("xhci: Add USB4 tunnel detection for USB3 devices on Intel hosts")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250227194529.2288718-1-maz@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Raspberry Pi is a major user of those chips and they discovered a bug -
when the end of a transfer ring segment is reached, up to four TRBs can
be prefetched from the next page even if the segment ends with link TRB
and on page boundary (the chip claims to support standard 4KB pages).
It also appears that if the prefetched TRBs belong to a different ring
whose doorbell is later rung, they may be used without refreshing from
system RAM and the endpoint will stay idle if their cycle bit is stale.
Other users complain about IOMMU faults on x86 systems, unsurprisingly.
Deal with it by using existing quirk which allocates a dummy page after
each transfer ring segment. This was seen to resolve both problems. RPi
came up with a more efficient solution, shortening each segment by four
TRBs, but it complicated the driver and they ditched it for this quirk.
Also rename the quirk and add VL805 device ID macro.
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Link: https://github.com/raspberrypi/linux/issues/4685
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=215906
CC: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250225095927.2512358-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for the 'eUSB2 Isochronous Endpoint Companion Descriptor'
introduced in the recent USB 2.0 specification 'USB 2.0 Double Isochronous
IN Bandwidth' ECN.
It allows embedded USB2 (eUSB2) devices to report and use higher bandwidths
for isochronous IN transfers in order to support higher camera resolutions
on the lid of laptops and tablets with minimal change to the USB2 protocol.
The motivation for expanding USB 2.0 is further clarified in an additional
Embedded USB2 version 2.0 (eUSB2v2) supplement to the USB 2.0
specification. It points out this is optimized for performance, power and
cost by using the USB 2.0 low-voltage, power efficient PHY and half-duplex
link for the asymmetric camera bandwidth needs, avoiding the costly and
complex full-duplex USB 3.x symmetric link and gigabit receivers.
eUSB2 devices that support the higher isochronous IN bandwidth and the new
descriptor can be identified by their device descriptor bcdUSB value of
0x0220
Co-developed-by: Amardeep Rai <amardeep.rai@intel.com>
Signed-off-by: Amardeep Rai <amardeep.rai@intel.com>
Signed-off-by: Kannappan R <r.kannappan@intel.com>
Co-developed-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20250220141339.1939448-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cdev->config might be NULL, so check it before dereferencing.
CC: stable <stable@kernel.org>
Fixes: 40e89ff575 ("usb: gadget: Set self-powered based on MaxPower and bmAttributes")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20250220120314.3614330-1-m.szyprowski@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is observed that on some systems an initial PPM reset during the boot
phase can trigger a timeout:
[ 6.482546] ucsi_acpi USBC000:00: failed to reset PPM!
[ 6.482551] ucsi_acpi USBC000:00: error -ETIMEDOUT: PPM init failed
Still, increasing the timeout value, albeit being the most straightforward
solution, eliminates the problem: the initial PPM reset may take up to
~8000-10000ms on some Lenovo laptops. When it is reset after the above
period of time (or even if ucsi_reset_ppm() is not called overall), UCSI
works as expected.
Moreover, if the ucsi_acpi module is loaded/unloaded manually after the
system has booted, reading the CCI values and resetting the PPM works
perfectly, without any timeout. Thus it's only a boot-time issue.
The reason for this behavior is not clear but it may be the consequence
of some tricks that the firmware performs or be an actual firmware bug.
As a workaround, increase the timeout to avoid failing the UCSI
initialization prematurely.
Fixes: b1b59e1607 ("usb: typec: ucsi: Increase command completion timeout value")
Cc: stable <stable@kernel.org>
Signed-off-by: Fedor Pchelkin <boddah8794@gmail.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250217105442.113486-3-boddah8794@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For the ACPI backend of UCSI the UCSI "registers" are just a memory copy
of the register values in an opregion. The ACPI implementation in the
BIOS ensures that the opregion contents are synced to the embedded
controller and it ensures that the registers (in particular CCI) are
synced back to the opregion on notifications. While there is an ACPI call
that syncs the actual registers to the opregion there is rarely a need to
do this and on some ACPI implementations it actually breaks in various
interesting ways.
The only reason to force a sync from the embedded controller is to poll
CCI while notifications are disabled. Only the ucsi core knows if this
is the case and guessing based on the current command is suboptimal, i.e.
leading to the following spurious assertion splat:
WARNING: CPU: 3 PID: 76 at drivers/usb/typec/ucsi/ucsi.c:1388 ucsi_reset_ppm+0x1b4/0x1c0 [typec_ucsi]
CPU: 3 UID: 0 PID: 76 Comm: kworker/3:0 Not tainted 6.12.11-200.fc41.x86_64 #1
Hardware name: LENOVO 21D0/LNVNB161216, BIOS J6CN45WW 03/17/2023
Workqueue: events_long ucsi_init_work [typec_ucsi]
RIP: 0010:ucsi_reset_ppm+0x1b4/0x1c0 [typec_ucsi]
Call Trace:
<TASK>
ucsi_init_work+0x3c/0xac0 [typec_ucsi]
process_one_work+0x179/0x330
worker_thread+0x252/0x390
kthread+0xd2/0x100
ret_from_fork+0x34/0x50
ret_from_fork_asm+0x1a/0x30
</TASK>
Thus introduce a ->poll_cci() method that works like ->read_cci() with an
additional forced sync and document that this should be used when polling
with notifications disabled. For all other backends that presumably don't
have this issue use the same implementation for both methods.
Fixes: fa48d7e816 ("usb: typec: ucsi: Do not call ACPI _DSM method for UCSI read operations")
Cc: stable <stable@kernel.org>
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Tested-by: Fedor Pchelkin <boddah8794@gmail.com>
Signed-off-by: Fedor Pchelkin <boddah8794@gmail.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250217105442.113486-2-boddah8794@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During probe, the TCPC alert interrupts are getting masked to
avoid unwanted interrupts during chip setup: this is ok to do
but there is no unmasking happening at any later time, which
means that the chip will not raise any interrupt, essentially
making it not functional as, while internally it does perform
all of the intended functions, it won't signal anything to the
outside.
Unmask the alert interrupts to fix functionality.
Fixes: ce08eaeb63 ("staging: typec: rt1711h typec chip driver")
Cc: stable <stable@kernel.org>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20250219114700.41700-1-angelogioacchino.delregno@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the USB gadget will be set as bus-powered based solely
on whether its bMaxPower is greater than 100mA, but this may miss
devices that may legitimately draw less than 100mA but still want
to report as bus-powered. Similarly during suspend & resume, USB
gadget is incorrectly marked as bus/self powered without checking
the bmAttributes field. Fix these by configuring the USB gadget
as self or bus powered based on bmAttributes, and explicitly set
it as bus-powered if it draws more than 100mA.
Cc: stable <stable@kernel.org>
Fixes: 5e5caf4fa8 ("usb: gadget: composite: Inform controller driver of self-powered")
Signed-off-by: Prashanth K <prashanth.k@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250217120328.2446639-1-prashanth.k@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently while UDC suspends, u_ether attempts to remote wakeup
the host if there are any pending transfers. However, if remote
wakeup fails, the UDC remains suspended but the is_suspend flag
is not set. And since is_suspend flag isn't set, the subsequent
eth_start_xmit() would queue USB requests to suspended UDC.
To fix this, bail out from gether_suspend() only if remote wakeup
operation is successful.
Cc: stable <stable@kernel.org>
Fixes: 0a1af6dfa0 ("usb: gadget: f_ecm: Add suspend/resume and remote wakeup support")
Signed-off-by: Prashanth K <prashanth.k@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250212100840.3812153-1-prashanth.k@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Syzbot once again identified a flaw in usb endpoint checking, see [1].
This time the issue stems from a commit authored by me (2eabb655a9
("usb: atm: cxacru: fix endpoint checking in cxacru_bind()")).
While using usb_find_common_endpoints() may usually be enough to
discard devices with wrong endpoints, in this case one needs more
than just finding and identifying the sufficient number of endpoints
of correct types - one needs to check the endpoint's address as well.
Since cxacru_bind() fills URBs with CXACRU_EP_CMD address in mind,
switch the endpoint verification approach to usb_check_XXX_endpoints()
instead to fix incomplete ep testing.
[1] Syzbot report:
usb 5-1: BOGUS urb xfer, pipe 3 != type 1
WARNING: CPU: 0 PID: 1378 at drivers/usb/core/urb.c:504 usb_submit_urb+0xc4e/0x18c0 drivers/usb/core/urb.c:503
...
RIP: 0010:usb_submit_urb+0xc4e/0x18c0 drivers/usb/core/urb.c:503
...
Call Trace:
<TASK>
cxacru_cm+0x3c8/0xe50 drivers/usb/atm/cxacru.c:649
cxacru_card_status drivers/usb/atm/cxacru.c:760 [inline]
cxacru_bind+0xcf9/0x1150 drivers/usb/atm/cxacru.c:1223
usbatm_usb_probe+0x314/0x1d30 drivers/usb/atm/usbatm.c:1058
cxacru_usb_probe+0x184/0x220 drivers/usb/atm/cxacru.c:1377
usb_probe_interface+0x641/0xbb0 drivers/usb/core/driver.c:396
really_probe+0x2b9/0xad0 drivers/base/dd.c:658
__driver_probe_device+0x1a2/0x390 drivers/base/dd.c:800
driver_probe_device+0x50/0x430 drivers/base/dd.c:830
...
Reported-and-tested-by: syzbot+ccbbc229a024fa3e13b5@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=ccbbc229a024fa3e13b5
Fixes: 2eabb655a9 ("usb: atm: cxacru: fix endpoint checking in cxacru_bind()")
Cc: stable@kernel.org
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Link: https://lore.kernel.org/r/20250213122259.730772-1-n.zhandarovich@fintech.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Propagate errors to the consumers when configuring the retimer so that
they can act on any failures as intended, for example:
ps883x_retimer 2-0008: failed to write conn_status_0: -5
pmic_glink_altmode.pmic_glink_altmode pmic_glink.altmode.0: failed to setup retimer to DP: -5
Fixes: 257a087c8b ("usb: typec: Add support for Parade PS8830 Type-C Retimer")
Cc: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20250218152933.22992-4-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure that the retimer is accessible before registering to avoid
having later consumer calls fail to configure it, something which, for
example, can lead to a hotplugged display not being recognised:
[drm:msm_dp_panel_read_sink_caps [msm]] *ERROR* read dpcd failed -110
Fixes: 257a087c8b ("usb: typec: Add support for Parade PS8830 Type-C Retimer")
Cc: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20250218152933.22992-3-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure that the retimer is fully setup before registering it to avoid
having consumers try to access it while it is being reset.
Fixes: 257a087c8b ("usb: typec: Add support for Parade PS8830 Type-C Retimer")
Cc: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20250218152933.22992-2-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the probe error handling to avoid unbalanced clock disable or
leaving regulators on after probe failure.
Note that the active-low reset pin should also be asserted to avoid
leaking current after disabling the regulators.
Fixes: 257a087c8b ("usb: typec: Add support for Parade PS8830 Type-C Retimer")
Cc: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20250218082243.9318-1-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the dt-bindings there are some platforms, which have a
dedicated USB power domain for DWC2 IP core supply. If the power domain
is switched off during system suspend then all USB register will lose
their settings.
Use GUSBCFG_TOUTCAL as a canary to detect that the power domain has
been powered off during suspend. Since the GOTGCTL_CURMODE_HOST doesn't
match on all platform with the current mode, additionally backup
GINTSTS. This works reliable to decide which registers should be
restored.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20250217134132.36786-4-wahrenst@gmx.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DWC2 runtime PM code reuses similar patterns to backup and
restore the registers. So consolidate them in USB mode specific
variants. This also has the advantage it is reusable for further
PM improvements.
Special care is taken for DCFG register during device mode restore.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/20250217134132.36786-3-wahrenst@gmx.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dwc2_restore_device_registers() use a single boolean
to decide about the register restoring behavior.
So replace this with a flags parameter, which can
be extended later.
No functional change intended.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/20250217134132.36786-2-wahrenst@gmx.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This hub is powered by digital and analog 3V3 power rails, so provide
the possibility to use different regulators for digital (vdd) and analog
(vdda) power rails.
Signed-off-by: Catalin Popescu <catalin.popescu@leica-geosystems.com>
Link: https://lore.kernel.org/r/20250213094338.1611389-3-catalin.popescu@leica-geosystems.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
hrtimer_setup() takes the callback function pointer as argument and
initializes the timer completely.
Replace hrtimer_init() and the open coded initialization of
hrtimer::function with the new setup mechanism.
Patch was created by using Coccinelle.
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Zack Rusin <zack.rusin@broadcom.com>
Link: https://lore.kernel.org/all/7fd2a1f72b3833e1fb36f56f2b28a08c1e64f47e.1738746904.git.namcao@linutronix.de
hrtimer_setup() takes the callback function pointer as argument and
initializes the timer completely.
Replace hrtimer_init() and the open coded initialization of
hrtimer::function with the new setup mechanism.
Patch was created by using Coccinelle.
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Zack Rusin <zack.rusin@broadcom.com>
Link: https://lore.kernel.org/all/80d59a56c76c76ace982417e4dc8ddd37a5441d7.1738746904.git.namcao@linutronix.de
hrtimer_setup() takes the callback function pointer as argument and
initializes the timer completely.
Replace hrtimer_init() and the open coded initialization of
hrtimer::function with the new setup mechanism.
Patch was created by using Coccinelle.
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Zack Rusin <zack.rusin@broadcom.com>
Link: https://lore.kernel.org/all/d703731ba61d1901c97758a60ccc3c209d21de0e.1738746904.git.namcao@linutronix.de
hrtimer_setup() takes the callback function pointer as argument and
initializes the timer completely.
Replace hrtimer_init() and the open coded initialization of
hrtimer::function with the new setup mechanism.
Patch was created by using Coccinelle.
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Zack Rusin <zack.rusin@broadcom.com>
Link: https://lore.kernel.org/all/7239d6211ffb0dff6351d0549d065277f2562793.1738746904.git.namcao@linutronix.de
hrtimer_setup() takes the callback function pointer as argument and
initializes the timer completely.
Replace hrtimer_init() and the open coded initialization of
hrtimer::function with the new setup mechanism.
Patch was created by using Coccinelle.
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Zack Rusin <zack.rusin@broadcom.com>
Link: https://lore.kernel.org/all/eeabb788995d7566017ebcff6cc2daa8da35432d.1738746904.git.namcao@linutronix.de
hrtimer_setup() takes the callback function pointer as argument and
initializes the timer completely.
Replace hrtimer_init() and the open coded initialization of
hrtimer::function with the new setup mechanism.
Patch was created by using Coccinelle.
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Zack Rusin <zack.rusin@broadcom.com>
Link: https://lore.kernel.org/all/ab5762d4fd512ac318e7962109d80547d38419cd.1738746904.git.namcao@linutronix.de
hrtimer_setup() takes the callback function pointer as argument and
initializes the timer completely.
Replace hrtimer_init() and the open coded initialization of
hrtimer::function with the new setup mechanism.
Patch was created by using Coccinelle.
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Zack Rusin <zack.rusin@broadcom.com>
Link: https://lore.kernel.org/all/a6e43ac5a90f975343e1cef2d8346b4697ec0473.1738746904.git.namcao@linutronix.de
Drop some defines that have never (really) been used, some of which are
duplicates (the read and write requests) and others which are just bogus
(the ioctl).
Signed-off-by: Johan Hovold <johan@kernel.org>
The Parade PS8830 is a USB4, DisplayPort and Thunderbolt 4 retimer,
controlled over I2C. It usually sits between a USB/DisplayPort PHY
and the Type-C connector, and provides orientation and altmode handling.
The boards that use this retimer are the ones featuring the Qualcomm
Snapdragon X Elite SoCs.
Add a driver with support for the following modes:
- DisplayPort 4-lanes
- DisplayPort 2-lanes + USB3
- USB3
There is another variant of this retimer which is called PS8833. It seems
to be really similar to the PS8830, so future-proof this driver by
naming it ps883x.
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250206-x1e80100-ps8830-v6-2-60b1e49cfa8d@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use syscon_regmap_lookup_by_phandle_args() which is a wrapper over
syscon_regmap_lookup_by_phandle() combined with getting the syscon
argument. Except simpler code this annotates within one line that given
phandle has arguments, so grepping for code would be easier.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250212202913.23443-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel Merrifield SoC uses these endpoints for tracing and they cannot
be re-allocated if being used because the side band flow control signals
are hard wired to certain endpoints:
• 1 High BW Bulk IN (IN#1) (RTIT)
• 1 1KB BW Bulk IN (IN#8) + 1 1KB BW Bulk OUT (Run Control) (OUT#8)
In device mode, since RTIT (EP#1) and EXI/RunControl (EP#8) uses
External Buffer Control (EBC) mode, these endpoints are to be mapped to
EBC mode (to be done by EXI target driver). Additionally TRB for RTIT
and EXI are maintained in STM (System Trace Module) unit and the EXI
target driver will as well configure the TRB location for EP #1 IN
and EP#8 (IN and OUT). Since STM/PTI and EXI hardware blocks manage
these endpoints and interface to OTG3 controller through EBC interface,
there is no need to enable any events (such as XferComplete etc)
for these end points.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Ferry Toth <fntoth@gmail.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250212193116.2487289-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The snps,reserved-endpoints property lists the reserved endpoints
that shouldn't be used for normal transfers. Add support for that
to the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Ferry Toth <fntoth@gmail.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250212193116.2487289-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prepare the gadget driver to handle the reserved endpoints that will be
not allocated at the initialisation time.
While at it, add a warning where the NULL endpoint should never happen.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Ferry Toth <fntoth@gmail.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250212193116.2487289-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A manual EC sysjump will restart the PPM and break communication with
the UCSI driver by disabling notifications in the initial PPM state.
Update cros_ec_ucsi to listen for PPM init events and treat them as a
system resume to re-establish communication with the PPM (ChromeOS EC).
Signed-off-by: Jameson Thies <jthies@google.com>
Reviewed-by: Łukasz Bartosik <ukaszb@chromium.org>
Reviewed-by: Benson Leung <bleung@chromium.org>
Link: https://lore.kernel.org/r/20250204024600.4138776-3-jthies@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As PD2.0 spec ("6.5.6.2 PSSourceOffTimer")，the PSSourceOffTimer is
used by the Policy Engine in Dual-Role Power device that is currently
acting as a Sink to timeout on a PS_RDY Message during a Power Role
Swap sequence. This condition leads to a Hard Reset for USB Type-A and
Type-B Plugs and Error Recovery for Type-C plugs and return to USB
Default Operation.
Therefore, after PSSourceOffTimer timeout, the tcpm state machine should
switch from PR_SWAP_SNK_SRC_SINK_OFF to ERROR_RECOVERY. This can also
solve the test items in the USB power delivery compliance test:
TEST.PD.PROT.SNK.12 PR_Swap – PSSourceOffTimer Timeout
[1] https://usb.org/document-library/usb-power-delivery-compliance-test-specification-0/USB_PD3_CTS_Q4_2025_OR.zip
Fixes: f0690a25a1 ("staging: typec: USB Type-C Port Manager (tcpm)")
Cc: stable <stable@kernel.org>
Signed-off-by: Jos Wang <joswang@lenovo.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Amit Sunil Dhamne <amitsd@google.com>
Link: https://lore.kernel.org/r/20250213134921.3798-1-joswang1221@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The role switch registration and set_role() can happen in parallel as they
are invoked independent of each other. There is a possibility that a driver
might spend significant amount of time in usb_role_switch_register() API
due to the presence of time intensive operations like component_add()
which operate under common mutex. This leads to a time window after
allocating the switch and before setting the registered flag where the set
role notifications are dropped. Below timeline summarizes this behavior
Thread1 | Thread2
usb_role_switch_register() |
| |
---> allocate switch |
| |
---> component_add() | usb_role_switch_set_role()
| | |
| | --> Drop role notifications
| | since sw->registered
| | flag is not set.
| |
--->Set registered flag.|
To avoid this, set the registered flag early on in the switch register
API.
Fixes: b787a3e781 ("usb: roles: don't get/set_role() when usb_role_switch is unregistered")
Cc: stable <stable@kernel.org>
Signed-off-by: Elson Roy Serrao <quic_eserrao@quicinc.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250206193950.22421-1-quic_eserrao@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The behaviour of kthread_create_worker() was recently changed to align
with the one of kthread_create(). The kthread worker is created but not
awaken by default. This is to allow the use of kthread_affine_preferred()
and kthread_bind[_mask]() with kthread workers. In order to keep the
old behaviour and wake the kthread up, kthread_run_worker() must be
used. All the pre-existing users have been converted, except for UVC
that was introduced in the same merge window as the API change.
This results in hangs:
INFO: task UVCG:82 blocked for more than 491 seconds.
Tainted: G T 6.13.0-rc2-00014-gb04e317b5226 #1
task:UVCG state:D stack:0 pid:82
Call Trace:
__schedule
schedule
schedule_preempt_disabled
kthread
? kthread_flush_work
ret_from_fork
ret_from_fork_asm
entry_INT80_32
Fix this with converting UVCG kworker to the new API.
Reported-by: kernel test robot <oliver.sang@intel.com>
Closes: https://lore.kernel.org/oe-lkp/202502121025.55bfa801-lkp@intel.com
Fixes: f0bbfbd16b ("usb: gadget: uvc: rework to enqueue in pump worker from encoded queue")
Cc: stable <stable@kernel.org>
Cc: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lore.kernel.org/r/20250212135514.30539-1-frederic@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Teclast disk used on Huawei hisi platforms doesn't work well,
losing connectivity intermittently if LPM is enabled.
Add quirk disable LPM to resolve the issue.
Signed-off-by: Lei Huang <huanglei@kylinos.cn>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20250212093829.7379-1-huanglei814@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
device_del() can lead to new work being scheduled in gadget->work
workqueue. This is observed, for example, with the dwc3 driver with the
following call stack:
device_del()
gadget_unbind_driver()
usb_gadget_disconnect_locked()
dwc3_gadget_pullup()
dwc3_gadget_soft_disconnect()
usb_gadget_set_state()
schedule_work(&gadget->work)
Move flush_work() after device_del() to ensure the workqueue is cleaned
up.
Fixes: 5702f75375 ("usb: gadget: udc-core: move sysfs_notify() to a workqueue")
Cc: stable <stable@kernel.org>
Signed-off-by: Roy Luo <royluo@google.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250204233642.666991-1-royluo@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When usb_control_msg is used in the get_bMaxPacketSize0 function, the
USB pipe does not include the endpoint device number. This can cause
failures when a usb hub port is reinitialized after encountering a bad
cable connection. As a result, the system logs the following error
messages:
usb usb2-port1: cannot reset (err = -32)
usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
usb usb2-port1: attempt power cycle
usb 2-1: new high-speed USB device number 5 using ci_hdrc
usb 2-1: device descriptor read/8, error -71
The problem began after commit 85d07c5562 ("USB: core: Unite old
scheme and new scheme descriptor reads"). There
usb_get_device_descriptor was replaced with get_bMaxPacketSize0. Unlike
usb_get_device_descriptor, the get_bMaxPacketSize0 function uses the
macro usb_rcvaddr0pipe, which does not include the endpoint device
number. usb_get_device_descriptor, on the other hand, used the macro
usb_rcvctrlpipe, which includes the endpoint device number.
By modifying the get_bMaxPacketSize0 function to use usb_rcvctrlpipe
instead of usb_rcvaddr0pipe, the issue can be resolved. This change will
ensure that the endpoint device number is included in the USB pipe,
preventing reinitialization failures. If the endpoint has not set the
device number yet, it will still work because the device number is 0 in
udev.
Cc: stable <stable@kernel.org>
Fixes: 85d07c5562 ("USB: core: Unite old scheme and new scheme descriptor reads")
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20250203105840.17539-1-eichest@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a frequent timeout during controller enter/exit from halt state
after toggling the run_stop bit by SW. This timeout occurs when
performing frequent role switches between host and device, causing
device enumeration issues due to the timeout. This issue was not present
when USB2 suspend PHY was disabled by passing the SNPS quirks
(snps,dis_u2_susphy_quirk and snps,dis_enblslpm_quirk) from the DTS.
However, there is a requirement to enable USB2 suspend PHY by setting of
GUSB2PHYCFG.ENBLSLPM and GUSB2PHYCFG.SUSPHY bits when controller starts
in gadget or host mode results in the timeout issue.
This commit addresses this timeout issue by ensuring that the bits
GUSB2PHYCFG.ENBLSLPM and GUSB2PHYCFG.SUSPHY are cleared before starting
the dwc3_gadget_run_stop sequence and restoring them after the
dwc3_gadget_run_stop sequence is completed.
Fixes: 72246da40f ("usb: Introduce DesignWare USB3 DRD Driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Selvarasu Ganesan <selvarasu.g@samsung.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250201163903.459-1-selvarasu.g@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The fastboot tool for communicating with Android bootloaders does not
work reliably with this device if USB 2 Link Power Management (LPM)
is enabled.
Various fastboot commands are affected, including the
following, which usually reproduces the problem within two tries:
fastboot getvar kernel
getvar:kernel FAILED (remote: 'GetVar Variable Not found')
This issue was hidden on many systems up until commit 63a1f84549
("xhci: stored cached port capability values in one place") as the xhci
driver failed to detect USB 2 LPM support if USB 3 ports were listed
before USB 2 ports in the "supported protocol capabilities".
Adding the quirk resolves the issue. No drawbacks are expected since
the device uses different USB product IDs outside of fastboot mode, and
since fastboot commands worked before, until LPM was enabled on the
tested system by the aforementioned commit.
Based on a patch from Forest <forestix@nom.one> from which most of the
code and commit message is taken.
Cc: stable <stable@kernel.org>
Reported-by: Forest <forestix@nom.one>
Closes: https://lore.kernel.org/hk8umj9lv4l4qguftdq1luqtdrpa1gks5l@sonic.net
Tested-by: Forest <forestix@nom.one>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250206151836.51742-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add Renesas R-Car D3 USB Download mode quirk and update comments
on all the other Renesas R-Car USB Download mode quirks to discern
them from each other. This follows R-Car Series, 3rd Generation
reference manual Rev.2.00 chapter 19.2.8 USB download mode .
Fixes: 6d853c9e41 ("usb: cdc-acm: Add DISABLE_ECHO for Renesas USB Download mode")
Cc: stable <stable@kernel.org>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20250209145708.106914-1-marek.vasut+renesas@mailbox.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we receive an initial fragment of size 8 bytes which specifies a wLength
of 1 byte (so the reassembled message is supposed to be 9 bytes long), and
we then receive a second fragment of size 9 bytes (which is not supposed to
happen), we currently wrongly bypass the fragment reassembly code but still
pass the pointer to the acm->notification_buffer to
acm_process_notification().
Make this less wrong by always going through fragment reassembly when we
expect more fragments.
Before this patch, receiving an overlong fragment could lead to `newctrl`
in acm_process_notification() being uninitialized data (instead of data
coming from the device).
Cc: stable <stable@kernel.org>
Fixes: ea2583529c ("cdc-acm: reassemble fragmented notifications")
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the first fragment is shorter than struct usb_cdc_notification, we can't
calculate an expected_size. Log an error and discard the notification
instead of reading lengths from memory outside the received data, which can
lead to memory corruption when the expected_size decreases between
fragments, causing `expected_size - acm->nb_index` to wrap.
This issue has been present since the beginning of git history; however,
it only leads to memory corruption since commit ea2583529c
("cdc-acm: reassemble fragmented notifications").
A mitigating factor is that acm_ctrl_irq() can only execute after userspace
has opened /dev/ttyACM*; but if ModemManager is running, ModemManager will
do that automatically depending on the USB device's vendor/product IDs and
its other interfaces.
Cc: stable <stable@kernel.org>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some Renesas HCs require firmware upload to work, this is handled by the
xhci_pci_renesas driver. Other variants of those chips load firmware from
a SPI flash and are ready to work with xhci_pci alone.
A refactor merged in v6.12 broke the latter configuration so that users
are finding their hardware ignored by the normal driver and are forced to
enable the firmware loader which isn't really necessary on their systems.
Let xhci_pci work with those chips as before when the firmware loader is
disabled by kernel configuration.
Fixes: 25f51b76f9 ("xhci-pci: Make xhci-pci-renesas a proper modular driver")
Cc: stable <stable@kernel.org>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219616
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219726
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Tested-by: Nicolai Buchwitz <nb@tipi-net.de>
Link: https://lore.kernel.org/r/20250128104529.58a79bfc@foxbook
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some new modem device ids and a couple of related cleanups of
the device id table.
All have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCZ64AAwAKCRALxc3C7H1l
CEf5AP9m/cucRzOid2mOQiCYpD5zhMn/MZnH/AFB647nN2dFZwD/Rgs64qk2ZZUI
49XbIl6SeoLWp2CdUS/M7ra+jKqa3AE=
=OkGu
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-6.14-rc3' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial device ids for 6.14-rc3
Here are some new modem device ids and a couple of related cleanups of
the device id table.
All have been in linux-next with no reported issues.
* tag 'usb-serial-6.14-rc3' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: drop MeiG Smart defines
USB: serial: option: fix Telit Cinterion FN990A name
USB: serial: option: add Telit Cinterion FN990B compositions
USB: serial: option: add MeiG Smart SLM828
The names RESERVE and RELEASE are not only used in <scsi/scsi_proto.h> but
also elsewhere in the kernel:
$ git grep -nHE 'define[[:blank:]]*(RESERVE|RELEASE)[[:blank:]]'
drivers/input/joystick/walkera0701.c:13:#define RESERVE 20000
drivers/s390/char/tape_std.h:56:#define RELEASE 0xD4 /* 3420 NOP, 3480 REJECT */
drivers/s390/char/tape_std.h:58:#define RESERVE 0xF4 /* 3420 NOP, 3480 REJECT */
Additionally, while the names of the symbolic constants RESERVE_10 and
RELEASE_10 include the command length, the command length is not included
in the RESERVE and RELEASE names. Address both issues by renaming the
RESERVE and RELEASE constants into RESERVE_6 and RELEASE_6 respectively.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20250210205031.2970833-1-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Several MeiG Smart modems apparently use the same product id, making the
defines even less useful.
Drop them in favour of using comments consistently to make the id table
slightly less unwieldy.
Cc: stable@vger.kernel.org
Acked-by: Chester A. Unal <chester.a.unal@arinc9.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
The correct name for FN990 is FN990A so use it in order to avoid
confusion with FN990B.
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
While the MIDI jacks are configured correctly, and the MIDIStreaming
endpoint descriptors are filled with the correct information,
bNumEmbMIDIJack and bLength are set incorrectly in these descriptors.
This does not matter when the numbers of in and out ports are equal, but
when they differ the host will receive broken descriptors with
uninitialized stack memory leaking into the descriptor for whichever
value is smaller.
The precise meaning of "in" and "out" in the port counts is not clearly
defined and can be confusing. But elsewhere the driver consistently
uses this to match the USB meaning of IN and OUT viewed from the host,
so that "in" ports send data to the host and "out" ports receive data
from it.
Cc: stable <stable@kernel.org>
Fixes: c8933c3f79 ("USB: gadget: f_midi: allow a dynamic number of input and output ports")
Signed-off-by: John Keeping <jkeeping@inmusicbrands.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20250130195035.3883857-1-jkeeping@inmusicbrands.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In dwc2_hsotg_udc_start(), e.g. when binding composite driver, "of_node"
is set to hsotg->dev->of_node.
It causes errors when binding the gadget driver several times, on
stm32mp157c-ev1 board. Below error is seen:
"pin PA10 already requested by 49000000.usb-otg; cannot claim for gadget.0"
The first time, no issue is seen as when registering the driver, of_node
isn't NULL:
-> gadget_dev_desc_UDC_store
-> usb_gadget_register_driver_owner
-> driver_register
...
-> really_probe -> pinctrl_bind_pins (no effect)
Then dwc2_hsotg_udc_start() sets of_node.
The second time (stop the gadget, reconfigure it, then start it again),
of_node has been set, so the probing code tries to acquire pins for the
gadget. These pins are hold by the controller, hence the error.
So clear gadget.dev.of_node in udc_stop() routine to avoid the issue.
Fixes: 7d7b22928b ("usb: gadget: s3c-hsotg: Propagate devicetree to gadget drivers")
Cc: stable <stable@kernel.org>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20250124173325.2747710-1-fabrice.gasnier@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Robert Morris created a test program which can cause
usb_hub_to_struct_hub() to dereference a NULL or inappropriate
pointer:
Oops: general protection fault, probably for non-canonical address
0xcccccccccccccccc: 0000 [#1] SMP DEBUG_PAGEALLOC PTI
CPU: 7 UID: 0 PID: 117 Comm: kworker/7:1 Not tainted 6.13.0-rc3-00017-gf44d154d6e3d #14
Hardware name: FreeBSD BHYVE/BHYVE, BIOS 14.0 10/17/2021
Workqueue: usb_hub_wq hub_event
RIP: 0010:usb_hub_adjust_deviceremovable+0x78/0x110
...
Call Trace:
<TASK>
? die_addr+0x31/0x80
? exc_general_protection+0x1b4/0x3c0
? asm_exc_general_protection+0x26/0x30
? usb_hub_adjust_deviceremovable+0x78/0x110
hub_probe+0x7c7/0xab0
usb_probe_interface+0x14b/0x350
really_probe+0xd0/0x2d0
? __pfx___device_attach_driver+0x10/0x10
__driver_probe_device+0x6e/0x110
driver_probe_device+0x1a/0x90
__device_attach_driver+0x7e/0xc0
bus_for_each_drv+0x7f/0xd0
__device_attach+0xaa/0x1a0
bus_probe_device+0x8b/0xa0
device_add+0x62e/0x810
usb_set_configuration+0x65d/0x990
usb_generic_driver_probe+0x4b/0x70
usb_probe_device+0x36/0xd0
The cause of this error is that the device has two interfaces, and the
hub driver binds to interface 1 instead of interface 0, which is where
usb_hub_to_struct_hub() looks.
We can prevent the problem from occurring by refusing to accept hub
devices that violate the USB spec by having more than one
configuration or interface.
Reported-and-tested-by: Robert Morris <rtm@csail.mit.edu>
Cc: stable <stable@kernel.org>
Closes: https://lore.kernel.org/linux-usb/95564.1737394039@localhost/
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/c27f3bf4-63d8-4fb5-ac82-09e3cd19f61c@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/usb/gadget/udc/renesas_usb3.c: In function 'renesas_usb3_probe':
drivers/usb/gadget/udc/renesas_usb3.c:2638:73: warning: '%d'
directive output may be truncated writing between 1 and 11 bytes into a
region of size 6 [-Wformat-truncation=]
2638 | snprintf(usb3_ep->ep_name, sizeof(usb3_ep->ep_name), "ep%d", i);
^~~~~~~~~~~~~~~~~~~~~~~~ ^~ ^
Fixes: 746bfe63bb ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Cc: stable@vger.kernel.org
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202501201409.BIQPtkeB-lkp@intel.com/
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
Link: https://lore.kernel.org/r/20250122081231.47594-1-guoren@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit c141ecc3ce ("of: Warn when of_property_read_bool() is
used on non-boolean properties") a warning is raised if this function
is used for property detection. of_property_present() is the correct
helper for this.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20250120144251.580981-1-alexander.stein@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current implementation sets the wMaxPacketSize of bulk in/out
endpoints to 1024 bytes at the end of the f_midi_bind function. However,
in cases where there is a failure in the first midi bind attempt,
consider rebinding. This scenario may encounter an f_midi_bind issue due
to the previous bind setting the bulk endpoint's wMaxPacketSize to 1024
bytes, which exceeds the ep->maxpacket_limit where configured dwc3 TX/RX
FIFO's maxpacket size of 512 bytes for IN/OUT endpoints in support HS
speed only.
Here the term "rebind" in this context refers to attempting to bind the
MIDI function a second time in certain scenarios. The situations where
rebinding is considered include:
* When there is a failure in the first UDC write attempt, which may be
caused by other functions bind along with MIDI.
* Runtime composition change : Example : MIDI,ADB to MIDI. Or MIDI to
MIDI,ADB.
This commit addresses this issue by resetting the wMaxPacketSize before
endpoint claim. And here there is no need to reset all values in the usb
endpoint descriptor structure, as all members except wMaxPacketSize and
bEndpointAddress have predefined values.
This ensures that restores the endpoint to its expected configuration,
and preventing conflicts with value of ep->maxpacket_limit. It also
aligns with the approach used in other function drivers, which treat
endpoint descriptors as if they were full speed before endpoint claim.
Fixes: 46decc82ff ("usb: gadget: unconditionally allocate hs/ss descriptor in bind operation")
Cc: stable@vger.kernel.org
Signed-off-by: Selvarasu Ganesan <selvarasu.g@samsung.com>
Link: https://lore.kernel.org/r/20250118060134.927-1-selvarasu.g@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'struct musb_fifo_cfg' are not modified in these drivers.
Constifying these structures moves some data to a read-only section, so
increase overall security.
On a x86_64, with allmodconfig, as an example:
Before:
======
text data bss dec hex filename
64381 5537 202 70120 111e8 drivers/usb/musb/musb_core.o
After:
=====
text data bss dec hex filename
64957 4929 202 70088 111c8 drivers/usb/musb/musb_core.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/26e6f3e25dc8e785d0034dd7e59918e455563e60.1737234596.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use dev_err_probe to silence EPROBE_DEFER error on boot on i.MX8ULP:
[ 0.127301] mxs_phy 29910000.usb-phy: can't get the clock, err=-517
Signed-off-by: Dominique Martinet <dominique.martinet@atmark-techno.com>
Link: https://lore.kernel.org/r/20250203-defer_usb2-v3-1-428182286ce3@atmark-techno.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is easier to keep all command-specific quirks in a single place. Move
them to ucsi_gram_sync_control() as the code now allows us to return
modified messages data.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250120-ucsi-merge-commands-v2-3-462a1ec22ecc@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is easier to keep all command-specific quirks in a single place. Move
them to ucsi_ccg_sync_control() as the code now allows us to return
modified messages data.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250120-ucsi-merge-commands-v2-2-462a1ec22ecc@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some of the drivers emulate or handle some of the commands in the
platform-specific way. The code ends up being split between several
callbacks, which complicates emulation.
In preparation to reworking such drivers, move read_cci() and
read_message_in() calls into ucsi_sync_control_common().
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Łukasz Bartosik <ukaszb@chromium.org>
Link: https://lore.kernel.org/r/20250120-ucsi-merge-commands-v2-1-462a1ec22ecc@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"maxim,max3421" DT compatible is missing its SPI device ID entry, not
allowing module autoloading and leading to the following message:
"SPI driver max3421-hcd has no spi_device_id for maxim,max3421"
Fix this by adding the spi_device_id table.
Signed-off-by: Alexander Stein <alexander.stein@mailbox.org>
Link: https://lore.kernel.org/r/20250128195114.56321-1-alexander.stein@mailbox.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 88785982a1 ("media: vb2: use lock if wait_prepare/finish
are NULL") it is no longer needed to set the wait_prepare/finish
vb2_ops callbacks as long as the lock field in vb2_queue is set.
Since the vb2_ops_wait_prepare/finish callbacks already rely on that field,
we can safely drop these callbacks.
This simplifies the code and this is a step towards the goal of deleting
these callbacks.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Link: https://lore.kernel.org/r/2fb746b8-31c4-44e0-bf7b-7a0758edf52a@xs4all.nl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable the UCSI commands UCSI_SET_NEW_CAM,
UCSI_GET_ERROR_STATUS, UCSI_GET_CAM_CS, and UCSI_GET_LPM_PPM_INFO
support in debugfs to enhance PD/TypeC debugging capability.
Signed-off-by: Madhu M <madhu.m@intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250118172455.701348-2-madhu.m@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rename the SET_UOM UCSI command to SET_CCOM as per the UCSI 3.0 spec.
Signed-off-by: Madhu M <madhu.m@intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250118172455.701348-1-madhu.m@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of driver core and debugfs updates for 6.14-rc1.
It's coming late in the merge cycle as there are a number of merge
conflicts with your tree now, and I wanted to make sure they were
working properly. To resolve them, look in linux-next, and I will send
the "fixup" patch as a response to the pull request.
Included in here is a bunch of driver core, PCI, OF, and platform rust
bindings (all acked by the different subsystem maintainers), hence the
merge conflict with the rust tree, and some driver core api updates to
mark things as const, which will also require some fixups due to new
stuff coming in through other trees in this merge window.
There are also a bunch of debugfs updates from Al, and there is at least
one user that does have a regression with these, but Al is working on
tracking down the fix for it. In my use (and everyone else's linux-next
use), it does not seem like a big issue at the moment.
Here's a short list of the things in here:
- driver core bindings for PCI, platform, OF, and some i/o functions.
We are almost at the "write a real driver in rust" stage now,
depending on what you want to do.
- misc device rust bindings and a sample driver to show how to use
them
- debugfs cleanups in the fs as well as the users of the fs api for
places where drivers got it wrong or were unnecessarily doing things
in complex ways.
- driver core const work, making more of the api take const * for
different parameters to make the rust bindings easier overall.
- other small fixes and updates
All of these have been in linux-next with all of the aforementioned
merge conflicts, and the one debugfs issue, which looks to be resolved
"soon".
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZ5koPA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymFHACfT5acDKf2Bov2Lc/5u3vBW/R6ChsAnj+LmgVI
hcDSPodj4szR40RRnzBd
=u5Ey
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core and debugfs updates from Greg KH:
"Here is the big set of driver core and debugfs updates for 6.14-rc1.
Included in here is a bunch of driver core, PCI, OF, and platform rust
bindings (all acked by the different subsystem maintainers), hence the
merge conflict with the rust tree, and some driver core api updates to
mark things as const, which will also require some fixups due to new
stuff coming in through other trees in this merge window.
There are also a bunch of debugfs updates from Al, and there is at
least one user that does have a regression with these, but Al is
working on tracking down the fix for it. In my use (and everyone
else's linux-next use), it does not seem like a big issue at the
moment.
Here's a short list of the things in here:
- driver core rust bindings for PCI, platform, OF, and some i/o
functions.
We are almost at the "write a real driver in rust" stage now,
depending on what you want to do.
- misc device rust bindings and a sample driver to show how to use
them
- debugfs cleanups in the fs as well as the users of the fs api for
places where drivers got it wrong or were unnecessarily doing
things in complex ways.
- driver core const work, making more of the api take const * for
different parameters to make the rust bindings easier overall.
- other small fixes and updates
All of these have been in linux-next with all of the aforementioned
merge conflicts, and the one debugfs issue, which looks to be resolved
"soon""
* tag 'driver-core-6.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (95 commits)
rust: device: Use as_char_ptr() to avoid explicit cast
rust: device: Replace CString with CStr in property_present()
devcoredump: Constify 'struct bin_attribute'
devcoredump: Define 'struct bin_attribute' through macro
rust: device: Add property_present()
saner replacement for debugfs_rename()
orangefs-debugfs: don't mess with ->d_name
octeontx2: don't mess with ->d_parent or ->d_parent->d_name
arm_scmi: don't mess with ->d_parent->d_name
slub: don't mess with ->d_name
sof-client-ipc-flood-test: don't mess with ->d_name
qat: don't mess with ->d_name
xhci: don't mess with ->d_iname
mtu3: don't mess wiht ->d_iname
greybus/camera - stop messing with ->d_iname
mediatek: stop messing with ->d_iname
netdevsim: don't embed file_operations into your structs
b43legacy: make use of debugfs_get_aux()
b43: stop embedding struct file_operations into their objects
carl9170: stop embedding file_operations into their objects
...
Here is the USB and Thunderbolt driver updates for 6.14-rc1. Nothing
huge in here, just lots of new hardware support and updates for existing
drivers. Changes here are:
- big gadget f_tcm driver update
- other gadget driver updates and fixes
- thunderbolt driver updates for new hardware and capabilities and
lots more debugging functionality to handle it when things aren't
working well.
- xhci driver updates
- new USB-serial device updates
- typec driver updates, including a chrome platform driver (acked by
the subsystem maintainers)
- other small driver updates
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZ5fI8A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yloPwCguHSvL8FM6Xwaxc/hdfalwI4c49AAnRECaMhR
mA1owvXgrKO3hjDHo2Sg
=Z5yt
-----END PGP SIGNATURE-----
Merge tag 'usb-6.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt driver updates from Greg KH:
"Here is the USB and Thunderbolt driver updates for 6.14-rc1. Nothing
huge in here, just lots of new hardware support and updates for
existing drivers. Changes here are:
- big gadget f_tcm driver update
- other gadget driver updates and fixes
- thunderbolt driver updates for new hardware and capabilities and
lots more debugging functionality to handle it when things aren't
working well.
- xhci driver updates
- new USB-serial device updates
- typec driver updates, including a chrome platform driver (acked by
the subsystem maintainers)
- other small driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-6.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (123 commits)
usb: hcd: Bump local buffer size in rh_string()
Revert "usb: gadget: u_serial: Disable ep before setting port to null to fix the crash caused by port being null"
usb: typec: tcpci: Prevent Sink disconnection before vPpsShutdown in SPR PPS
usb: xhci: tegra: Fix OF boolean read warning
usb: host: xhci-plat: add support compatible ID PNP0D15
usb: typec: ucsi: Add a macro definition for UCSI v1.0
usb: dwc3: core: Defer the probe until USB power supply ready
usbip: Correct format specifier for seqnum from %d to %u
usbip: Fix seqnum sign extension issue in vhci_tx_urb
dt-bindings: usb: snps,dwc3: Split core description
usb: quirks: Add NO_LPM quirk for TOSHIBA TransMemory-Mx device
usb: dwc3: gadget: Reinitiate stream for all host NoStream behavior
USB: Use str_enable_disable-like helpers
USB: gadget: Use str_enable_disable-like helpers
USB: phy: Use str_enable_disable-like helpers
USB: typec: Use str_enable_disable-like helpers
USB: host: Use str_enable_disable-like helpers
USB: Replace own str_plural with common one
USB: serial: quatech2: fix null-ptr-deref in qt2_process_read_urb()
usb: phy: Remove API devm_usb_put_phy()
...
Updates to the usual drivers (ufs, lpfc, fnic, qla2xx, mpi3mr) The
major core change is the renaming of the slave_ methods plus a bit of
constification. The rest are minor updates and fixes.
Signed-off-by: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCZ5ZQKSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishQMdAQCyVlDZ
v/3EFCuC4U1l70mMu8t+F4RPvqYxM3QPCi5dDQEA751YN/kaqxeXZDqGUKCAOE3K
Nl4XFTfLEkDVrQFFqPc=
=9sV8
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"Updates to the usual drivers (ufs, lpfc, fnic, qla2xx, mpi3mr).
The major core change is the renaming of the slave_ methods plus a bit
of constification. The rest are minor updates and fixes"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (103 commits)
scsi: fnic: Propagate SCSI error code from fnic_scsi_drv_init()
scsi: fnic: Test for memory allocation failure and return error code
scsi: fnic: Return appropriate error code from failure of scsi drv init
scsi: fnic: Return appropriate error code for mem alloc failure
scsi: fnic: Remove always-true IS_FNIC_FCP_INITIATOR macro
scsi: fnic: Fix use of uninitialized value in debug message
scsi: fnic: Delete incorrect debugfs error handling
scsi: fnic: Remove unnecessary else to fix warning in FDLS FIP
scsi: fnic: Remove extern definition from .c files
scsi: fnic: Remove unnecessary else and unnecessary break in FDLS
scsi: mpi3mr: Fix possible crash when setting up bsg fails
scsi: ufs: bsg: Set bsg_queue to NULL after removal
scsi: ufs: bsg: Delete bsg_dev when setting up bsg fails
scsi: st: Don't set pos_unknown just after device recognition
scsi: aic7xxx: Fix build 'aicasm' warning
scsi: Revert "scsi: ufs: core: Probe for EXT_IID support"
scsi: storvsc: Ratelimit warning logs to prevent VM denial of service
scsi: scsi_debug: Constify sdebug_driver_template
scsi: documentation: Corrections for struct updates
scsi: driver-api: documentation: Change what is added to docbook
...
- Use usleep_range() instead of msleep() in acpi_os_sleep() to reduce
excessive delays due to timer inaccuracy, mostly affecting system
suspend and resume (Rafael Wysocki).
- Use str_enabled_disabled() string helpers in the ACPI tables parsing
code to make it easier to follow (Sunil V L).
- Update device properties parsing on systems using ACPI so that
data firmware nodes resulting from _DSD evaluation are treated
as available in firmware nodes walks (Sakari Ailus).
- Fix missing guid_t declaration in linux/prmt.h (Robert Richter).
- Update the GHES handling code to follow the global panic= policy
instead of overriding it by force-rebooting the system after a
fatal HW error has been reported (Borislav Petkov).
- Update messages printed by the ACPI battery driver to always
refer to driver extensions as "hooks" to avoid confusion with
similar functionality in the power supply subsystem in the
future (Thomas Weißschuh).
- Fix .probe() error path cleanup in the ACPI fan driver to avoid
memory leaks (Joe Hattori).
- Constify 'struct bin_attribute' in some places in the ACPI subsystem
and mark it as __ro_after_init in one place to prevent binary blob
attributes from being updated (Thomas Weißschuh)
- Add empty stubs for several ACPI-related symbols so that they can be
used when CONFIG_ACPI is unset and use them for removing unnecessary
conditional compilation from the ipu-bridge driver (Ricardo Ribalda).
-----BEGIN PGP SIGNATURE-----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=B/1O
-----END PGP SIGNATURE-----
Merge tag 'acpi-6.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"The most significant change here is replacing msleep() in
acpi_os_sleep() with usleep_range() to reduce spurious sleep time due
to timer inaccuracy which may spectacularly reduce the duration of
system suspend and resume transitions on some systems.
All of the other changes fall into the fixes and cleanups category
this time.
Specifics:
- Use usleep_range() instead of msleep() in acpi_os_sleep() to reduce
excessive delays due to timer inaccuracy, mostly affecting system
suspend and resume (Rafael Wysocki)
- Use str_enabled_disabled() string helpers in the ACPI tables
parsing code to make it easier to follow (Sunil V L)
- Update device properties parsing on systems using ACPI so that data
firmware nodes resulting from _DSD evaluation are treated as
available in firmware nodes walks (Sakari Ailus)
- Fix missing guid_t declaration in linux/prmt.h (Robert Richter)
- Update the GHES handling code to follow the global panic= policy
instead of overriding it by force-rebooting the system after a
fatal HW error has been reported (Borislav Petkov)
- Update messages printed by the ACPI battery driver to always refer
to driver extensions as "hooks" to avoid confusion with similar
functionality in the power supply subsystem in the future (Thomas
Weißschuh)
- Fix .probe() error path cleanup in the ACPI fan driver to avoid
memory leaks (Joe Hattori)
- Constify 'struct bin_attribute' in some places in the ACPI
subsystem and mark it as __ro_after_init in one place to prevent
binary blob attributes from being updated (Thomas Weißschuh)
- Add empty stubs for several ACPI-related symbols so that they can
be used when CONFIG_ACPI is unset and use them for removing
unnecessary conditional compilation from the ipu-bridge driver
(Ricardo Ribalda)"
* tag 'acpi-6.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
APEI: GHES: Have GHES honor the panic= setting
ACPI: PRM: Fix missing guid_t declaration in linux/prmt.h
ACPI: tables: Use string choice helpers
ACPI: property: Consider data nodes as being available
media: ipu-bridge: Remove unneeded conditional compilations
ACPI: bus: implement acpi_device_hid when !ACPI
ACPI: bus: implement for_each_acpi_consumer_dev when !ACPI
ACPI: header: implement acpi_device_handle when !ACPI
ACPI: bus: implement acpi_get_physical_device_location when !ACPI
ACPI: bus: implement for_each_acpi_dev_match when !ACPI
ACPI: bus: change the prototype for acpi_get_physical_device_location
ACPI: fan: cleanup resources in the error path of .probe()
ACPI: battery: Rename extensions to hook in messages
ACPI: OSL: Use usleep_range() in acpi_os_sleep()
ACPI: sysfs: Constify 'struct bin_attribute'
ACPI: BGRT: Constify 'struct bin_attribute'
ACPI: BGRT: Mark bin_attribute as __ro_after_init
1) Per-CPU kthreads must stay affine to a single CPU and never execute
relevant code on any other CPU. This is currently handled by smpboot
code which takes care of CPU-hotplug operations. Affinity here is
a correctness constraint.
2) Some kthreads _have_ to be affine to a specific set of CPUs and can't
run anywhere else. The affinity is set through kthread_bind_mask()
and the subsystem takes care by itself to handle CPU-hotplug
operations. Affinity here is assumed to be a correctness constraint.
3) Per-node kthreads _prefer_ to be affine to a specific NUMA node. This
is not a correctness constraint but merely a preference in terms of
memory locality. kswapd and kcompactd both fall into this category.
The affinity is set manually like for any other task and CPU-hotplug
is supposed to be handled by the relevant subsystem so that the task
is properly reaffined whenever a given CPU from the node comes up.
Also care should be taken so that the node affinity doesn't cross
isolated (nohz_full) cpumask boundaries.
4) Similar to the previous point except kthreads have a _preferred_
affinity different than a node. Both RCU boost kthreads and RCU
exp kworkers fall into this category as they refer to "RCU nodes"
from a distinctly distributed tree.
Currently the preferred affinity patterns (3 and 4) have at least 4
identified users, with more or less success when it comes to handle
CPU-hotplug operations and CPU isolation. Each of which do it in its own
ad-hoc way.
This is an infrastructure proposal to handle this with the following API
changes:
_ kthread_create_on_node() automatically affines the created kthread to
its target node unless it has been set as per-cpu or bound with
kthread_bind[_mask]() before the first wake-up.
- kthread_affine_preferred() is a new function that can be called right
after kthread_create_on_node() to specify a preferred affinity
different than the specified node.
When the preferred affinity can't be applied because the possible
targets are offline or isolated (nohz_full), the kthread is affine
to the housekeeping CPUs (which means to all online CPUs most of the
time or only the non-nohz_full CPUs when nohz_full= is set).
kswapd, kcompactd, RCU boost kthreads and RCU exp kworkers have been
converted, along with a few old drivers.
Summary of the changes:
* Consolidate a bunch of ad-hoc implementations of kthread_run_on_cpu()
* Introduce task_cpu_fallback_mask() that defines the default last
resort affinity of a task to become nohz_full aware
* Add some correctness check to ensure kthread_bind() is always called
before the first kthread wake up.
* Default affine kthread to its preferred node.
* Convert kswapd / kcompactd and remove their halfway working ad-hoc
affinity implementation
* Implement kthreads preferred affinity
* Unify kthread worker and kthread API's style
* Convert RCU kthreads to the new API and remove the ad-hoc affinity
implementation.
-----BEGIN PGP SIGNATURE-----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=g8In
-----END PGP SIGNATURE-----
Merge tag 'kthread-for-6.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/frederic/linux-dynticks
Pull kthread updates from Frederic Weisbecker:
"Kthreads affinity follow either of 4 existing different patterns:
1) Per-CPU kthreads must stay affine to a single CPU and never
execute relevant code on any other CPU. This is currently handled
by smpboot code which takes care of CPU-hotplug operations.
Affinity here is a correctness constraint.
2) Some kthreads _have_ to be affine to a specific set of CPUs and
can't run anywhere else. The affinity is set through
kthread_bind_mask() and the subsystem takes care by itself to
handle CPU-hotplug operations. Affinity here is assumed to be a
correctness constraint.
3) Per-node kthreads _prefer_ to be affine to a specific NUMA node.
This is not a correctness constraint but merely a preference in
terms of memory locality. kswapd and kcompactd both fall into this
category. The affinity is set manually like for any other task and
CPU-hotplug is supposed to be handled by the relevant subsystem so
that the task is properly reaffined whenever a given CPU from the
node comes up. Also care should be taken so that the node affinity
doesn't cross isolated (nohz_full) cpumask boundaries.
4) Similar to the previous point except kthreads have a _preferred_
affinity different than a node. Both RCU boost kthreads and RCU
exp kworkers fall into this category as they refer to "RCU nodes"
from a distinctly distributed tree.
Currently the preferred affinity patterns (3 and 4) have at least 4
identified users, with more or less success when it comes to handle
CPU-hotplug operations and CPU isolation. Each of which do it in its
own ad-hoc way.
This is an infrastructure proposal to handle this with the following
API changes:
- kthread_create_on_node() automatically affines the created kthread
to its target node unless it has been set as per-cpu or bound with
kthread_bind[_mask]() before the first wake-up.
- kthread_affine_preferred() is a new function that can be called
right after kthread_create_on_node() to specify a preferred
affinity different than the specified node.
When the preferred affinity can't be applied because the possible
targets are offline or isolated (nohz_full), the kthread is affine to
the housekeeping CPUs (which means to all online CPUs most of the time
or only the non-nohz_full CPUs when nohz_full= is set).
kswapd, kcompactd, RCU boost kthreads and RCU exp kworkers have been
converted, along with a few old drivers.
Summary of the changes:
- Consolidate a bunch of ad-hoc implementations of
kthread_run_on_cpu()
- Introduce task_cpu_fallback_mask() that defines the default last
resort affinity of a task to become nohz_full aware
- Add some correctness check to ensure kthread_bind() is always
called before the first kthread wake up.
- Default affine kthread to its preferred node.
- Convert kswapd / kcompactd and remove their halfway working ad-hoc
affinity implementation
- Implement kthreads preferred affinity
- Unify kthread worker and kthread API's style
- Convert RCU kthreads to the new API and remove the ad-hoc affinity
implementation"
* tag 'kthread-for-6.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/frederic/linux-dynticks:
kthread: modify kernel-doc function name to match code
rcu: Use kthread preferred affinity for RCU exp kworkers
treewide: Introduce kthread_run_worker[_on_cpu]()
kthread: Unify kthread_create_on_cpu() and kthread_create_worker_on_cpu() automatic format
rcu: Use kthread preferred affinity for RCU boost
kthread: Implement preferred affinity
mm: Create/affine kswapd to its preferred node
mm: Create/affine kcompactd to its preferred node
kthread: Default affine kthread to its preferred NUMA node
kthread: Make sure kthread hasn't started while binding it
sched,arm64: Handle CPU isolation on last resort fallback rq selection
arm64: Exclude nohz_full CPUs from 32bits el0 support
lib: test_objpool: Use kthread_run_on_cpu()
kallsyms: Use kthread_run_on_cpu()
soc/qman: test: Use kthread_run_on_cpu()
arm/bL_switcher: Use kthread_run_on_cpu()
-----BEGIN PGP SIGNATURE-----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=EXYs
-----END PGP SIGNATURE-----
Merge tag 'for-6.14/block-20250118' of git://git.kernel.dk/linux
Pull block updates from Jens Axboe:
- NVMe pull requests via Keith:
- Target support for PCI-Endpoint transport (Damien)
- TCP IO queue spreading fixes (Sagi, Chaitanya)
- Target handling for "limited retry" flags (Guixen)
- Poll type fix (Yongsoo)
- Xarray storage error handling (Keisuke)
- Host memory buffer free size fix on error (Francis)
- MD pull requests via Song:
- Reintroduce md-linear (Yu Kuai)
- md-bitmap refactor and fix (Yu Kuai)
- Replace kmap_atomic with kmap_local_page (David Reaver)
- Quite a few queue freeze and debugfs deadlock fixes
Ming introduced lockdep support for this in the 6.13 kernel, and it
has (unsurprisingly) uncovered quite a few issues
- Use const attributes for IO schedulers
- Remove bio ioprio wrappers
- Fixes for stacked device atomic write support
- Refactor queue affinity helpers, in preparation for better supporting
isolated CPUs
- Cleanups of loop O_DIRECT handling
- Cleanup of BLK_MQ_F_* flags
- Add rotational support for null_blk
- Various fixes and cleanups
* tag 'for-6.14/block-20250118' of git://git.kernel.dk/linux: (106 commits)
block: Don't trim an atomic write
block: Add common atomic writes enable flag
md/md-linear: Fix a NULL vs IS_ERR() bug in linear_add()
block: limit disk max sectors to (LLONG_MAX >> 9)
block: Change blk_stack_atomic_writes_limits() unit_min check
block: Ensure start sector is aligned for stacking atomic writes
blk-mq: Move more error handling into blk_mq_submit_bio()
block: Reorder the request allocation code in blk_mq_submit_bio()
nvme: fix bogus kzalloc() return check in nvme_init_effects_log()
md/md-bitmap: move bitmap_{start, end}write to md upper layer
md/raid5: implement pers->bitmap_sector()
md: add a new callback pers->bitmap_sector()
md/md-bitmap: remove the last parameter for bimtap_ops->endwrite()
md/md-bitmap: factor behind write counters out from bitmap_{start/end}write()
md: Replace deprecated kmap_atomic() with kmap_local_page()
md: reintroduce md-linear
partitions: ldm: remove the initial kernel-doc notation
blk-cgroup: rwstat: fix kernel-doc warnings in header file
blk-cgroup: fix kernel-doc warnings in header file
nbd: fix partial sending
...
Merge ACPI battery and fan drivers updates and miscellaneous ACPI
chanages for 6.14:
- Update messages printed by the ACPI battery driver to always
refer to driver extensions as "hooks" to avoid confusion with
similar functionality in the power supply subsystem in the
future (Thomas Weißschuh).
- Fix .probe() error path cleanup in the ACPI fan driver to avoid
memory leaks (Joe Hattori).
- Constify 'struct bin_attribute' in some places in the ACPI subsystem
and mark it as __ro_after_init in one place to prevent binary blob
attributes from being updated (Thomas Weißschuh)
- Add empty stubs for several ACPI-related symbols so that they can be
used when CONFIG_ACPI is unset and use them for removing unnecessary
conditional compilation from the ipu-bridge driver (Ricardo Ribalda).
* acpi-battery:
ACPI: battery: Rename extensions to hook in messages
* acpi-fan:
ACPI: fan: cleanup resources in the error path of .probe()
* acpi-misc:
media: ipu-bridge: Remove unneeded conditional compilations
ACPI: bus: implement acpi_device_hid when !ACPI
ACPI: bus: implement for_each_acpi_consumer_dev when !ACPI
ACPI: header: implement acpi_device_handle when !ACPI
ACPI: bus: implement acpi_get_physical_device_location when !ACPI
ACPI: bus: implement for_each_acpi_dev_match when !ACPI
ACPI: bus: change the prototype for acpi_get_physical_device_location
ACPI: sysfs: Constify 'struct bin_attribute'
ACPI: BGRT: Constify 'struct bin_attribute'
ACPI: BGRT: Mark bin_attribute as __ro_after_init
GCC is not happy about the buffer size:
drivers/usb/core/hcd.c:441:48: error: ‘%s’ directive output may be truncated writing up to 64 bytes into a region of size between 35 and 99 [-Werror=format-truncation=]
441 | snprintf (buf, sizeof buf, "%s %s %s", init_utsname()->sysname,
| ^~
442 | init_utsname()->release, hcd->driver->description);
| ~~~~~~~~~~~~~~~~~~~~~~~
Bump the size to get it enough for the possible strings.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250116160543.216913-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Source can drop its output voltage to the minimum of the requested
PPS APDO voltage range when it is in Current Limit Mode. If this voltage
falls within the range of vPpsShutdown, the Source initiates a Hard
Reset and discharges Vbus. However, currently the Sink may disconnect
before the voltage reaches vPpsShutdown, leading to unexpected behavior.
Prevent premature disconnection by setting the Sink's disconnect
threshold to the minimum vPpsShutdown value. Additionally, consider the
voltage drop due to IR drop when calculating the appropriate threshold.
This ensures a robust and reliable interaction between the Source and
Sink during SPR PPS Current Limit Mode operation.
Fixes: 4288debeaa ("usb: typec: tcpci: Fix up sink disconnect thresholds for PD")
Cc: stable <stable@kernel.org>
Signed-off-by: Kyle Tso <kyletso@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20250114142435.2093857-1-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit c141ecc3ce ("of: Warn when of_property_read_bool() is
used on non-boolean properties") was added, the following warning is
observed for the Tegra XHCI driver ...
OF: /bus@0/usb@3610000: Read of boolean property 'power-domains' with
a value.
Previously, of_property_read_bool() was used to determine if a property
was present but has now been replaced by of_property_present(). The
warning is meant to prevent new users but this user existed before the
change was made. Fix this by updating the Tegra XHCI driver to use
of_property_present() function to determine if the 'power-domains'
property is present.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20250116153829.477360-1-jonathanh@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support compatible ID PNP0D15 which declare that the xHCI
controller doesn't support standard debug capability.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20250116125141.25856-1-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many platforms from Qualcomm(before X elite) still use UCSI v1.0,
part of them hardcoded the version number to dsdt, add this for them.
Signed-off-by: Pengyu Luo <mitltlatltl@gmail.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250113175131.590683-1-mitltlatltl@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, DWC3 driver attempts to acquire the USB power supply only
once during the probe. If the USB power supply is not ready at that
time, the driver simply ignores the failure and continues the probe,
leading to permanent non-functioning of the gadget vbus_draw callback.
Address this problem by delaying the dwc3 driver initialization until
the USB power supply is registered.
Fixes: 6f0764b5ad ("usb: dwc3: add a power supply for current control")
Cc: stable <stable@kernel.org>
Signed-off-by: Kyle Tso <kyletso@google.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250115044548.2701138-1-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The seqnum field in USBIP protocol is an unsigned value.
So we fix the format specifier from %d to %u to correctly
display the value.
Signed-off-by: Xiong Nandi <xndchn@gmail.com>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20241231161539.20192-3-xndchn@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The atomic_inc_return function returns an int, while priv->seqnum is an
unsigned long. So we must cast the result to u32 to prevent potential
sign extension and size mismatch issues.
Signed-off-by: Xiong Nandi <xndchn@gmail.com>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20241231161539.20192-2-xndchn@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are the USB-serial updates for 6.14-rc1, including:
- fix a long-standing NULL-deref issue in quatech2
- add support for hardware flow control to ch341
Included is also a related clean up.
All have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCZ4oQHgAKCRALxc3C7H1l
CCEJAQDUWUamPwhyoeqzb1xO93Sbym6TTXSP+WlZqoBxrEAAJQD/ZnF5l0JxYmmO
DJ8UX5IF/H66psT0gBcjlbYoVC3UkQE=
=uRTH
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-6.14-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Merge usb-serial updates from Johan:
USB-serial updates for 6.14-rc1
Here are the USB-serial updates for 6.14-rc1, including:
- fix a long-standing NULL-deref issue in quatech2
- add support for hardware flow control to ch341
Included is also a related clean up.
All have been in linux-next with no reported issues.
* tag 'usb-serial-6.14-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: quatech2: fix null-ptr-deref in qt2_process_read_urb()
USB: serial: ch341: use fix-width types consistently
USB: serial: ch341: add hardware flow control RTS/CTS
TOSHIBA TransMemory-Mx is a good performence flash device, but it
doesn't work well with LPM on Huawei hisi platform, so let's disable
LPM to resolve the issue.
Signed-off-by: Miao Li <limiao@kylinos.cn>
Link: https://lore.kernel.org/r/20250113085619.44371-1-limiao870622@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are too many different host behaviors when it comes to NoStream
handling, and not everyone follows the USB and xHCI spec. The DWC3
driver attempts to do some guess work to interop with different hosts,
but it can't cover everything. Let's keep it simple and treat every host
the same: just retry on NoStream after a 100ms of no response delay.
Note that some hosts cannot handle frequent retries. This may affect
performance on certain defective hosts, but NoStream is a rare
occurrence and interoperability is more important.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/b92ae94c86f01f165d5f178b7767898573b6dc75.1736819308.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace ternary (condition ? "enable" : "disable") syntax with helpers
from string_choices.h because:
1. Simple function call with one argument is easier to read. Ternary
operator has three arguments and with wrapping might lead to quite
long code.
2. Is slightly shorter thus also easier to read.
3. It brings uniformity in the text - same string.
4. Allows deduping by the linker, which results in a smaller binary
file.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250114-str-enable-disable-usb-v1-6-c8405df47c19@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace ternary (condition ? "enable" : "disable") syntax with helpers
from string_choices.h because:
1. Simple function call with one argument is easier to read. Ternary
operator has three arguments and with wrapping might lead to quite
long code.
2. Is slightly shorter thus also easier to read.
3. It brings uniformity in the text - same string.
4. Allows deduping by the linker, which results in a smaller binary
file.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250114-str-enable-disable-usb-v1-5-c8405df47c19@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace ternary (condition ? "enable" : "disable") syntax with helpers
from string_choices.h because:
1. Simple function call with one argument is easier to read. Ternary
operator has three arguments and with wrapping might lead to quite
long code.
2. Is slightly shorter thus also easier to read.
3. It brings uniformity in the text - same string.
4. Allows deduping by the linker, which results in a smaller binary
file.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250114-str-enable-disable-usb-v1-4-c8405df47c19@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace ternary (condition ? "enable" : "disable") syntax with helpers
from string_choices.h because:
1. Simple function call with one argument is easier to read. Ternary
operator has three arguments and with wrapping might lead to quite
long code.
2. Is slightly shorter thus also easier to read.
3. It brings uniformity in the text - same string.
4. Allows deduping by the linker, which results in a smaller binary
file.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250114-str-enable-disable-usb-v1-3-c8405df47c19@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace ternary (condition ? "enable" : "disable") syntax with helpers
from string_choices.h because:
1. Simple function call with one argument is easier to read. Ternary
operator has three arguments and with wrapping might lead to quite
long code.
2. Is slightly shorter thus also easier to read.
3. It brings uniformity in the text - same string.
4. Allows deduping by the linker, which results in a smaller binary
file.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250114-str-enable-disable-usb-v1-2-c8405df47c19@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch addresses a null-ptr-deref in qt2_process_read_urb() due to
an incorrect bounds check in the following:
if (newport > serial->num_ports) {
dev_err(&port->dev,
"%s - port change to invalid port: %i\n",
__func__, newport);
break;
}
The condition doesn't account for the valid range of the serial->port
buffer, which is from 0 to serial->num_ports - 1. When newport is equal
to serial->num_ports, the assignment of "port" in the
following code is out-of-bounds and NULL:
serial_priv->current_port = newport;
port = serial->port[serial_priv->current_port];
The fix checks if newport is greater than or equal to serial->num_ports
indicating it is out-of-bounds.
Reported-by: syzbot <syzbot+506479ebf12fe435d01a@syzkaller.appspotmail.com>
Closes: https://syzkaller.appspot.com/bug?extid=506479ebf12fe435d01a
Fixes: f7a33e608d ("USB: serial: add quatech2 usb to serial driver")
Cc: <stable@vger.kernel.org> # 3.5
Signed-off-by: Qasim Ijaz <qasdev00@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
We need the debugfs / driver-core fixes in here as well for testing and
to build on top of.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Static devm_usb_phy_match() is only called by API devm_usb_put_phy(), and
the API has no caller now.
Remove the API and the static function.
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20250112-remove_api-v1-1-49cc8f792ac9@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As PD2.0 spec ("8.3.3.2.3 PE_SRC_Send_Capabilities state"), after the
Source receives the GoodCRC Message from the Sink in response to the
Source_Capabilities message, it should start the SenderResponseTimer,
after the timer times out, the state machine transitions to the
HARD_RESET state.
Fixes: f0690a25a1 ("staging: typec: USB Type-C Port Manager (tcpm)")
Cc: stable@vger.kernel.org
Signed-off-by: Jos Wang <joswang@lenovo.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20250105135245.7493-1-joswang1221@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When inserting a USB device, examining hcd->rsrc_start can be
helpful in identifying which hcd is mounted, as the physical
address represented here is typically unique.
The following code snippet demonstrates this:
struct usb_hcd *hcd = bus_to_hcd(udev->bus);
unsigned long long usb_hcd_addr = (unsigned long long)hcd->rsrc_start;
However, this approach has limitations now. For USB hosts with an
MMIO interface, the effectiveness of this method is restricted to
USB 2.0.
Because commit 3429e91a66 ("usb: host: xhci: add platform driver
support") assigned res->start to hcd->rsrc_start. But
shared_hcd->rsrc_start remains unassigned, which is also necessary
in certain scenarios.
Fixes: 3429e91a66 ("usb: host: xhci: add platform driver support")
Co-developed-by: Xu Rao <raoxu@uniontech.com>
Signed-off-by: Xu Rao <raoxu@uniontech.com>
Signed-off-by: WangYuli <wangyuli@uniontech.com>
Link: https://lore.kernel.org/r/186B9F56972457B4+20250107133854.172309-1-wangyuli@uniontech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 533561a8aa ("usb: dwc3: omap: Use
devm_regulator_get_optional()") assumed NULL was returned, but
devm_regulator_get_optional() returns -ENODEV rather than NULL like
other *_get_optional() functions.
Fixes: 533561a8aa ("usb: dwc3: omap: Use devm_regulator_get_optional()")
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250109170748.3852439-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Letting the compiler remove these functions when the kernel is built
without CONFIG_PM_SLEEP support is simpler and less error prone than the
use of #ifdef based kernel configuration guards.
Signed-off-by: Raphael Gallais-Pou <rgallaispou@gmail.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250109152055.52931-1-rgallaispou@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the system begins to enter suspend mode, dwc3_suspend() is called
by PM suspend. There is a problem that if someone interrupt the system
suspend process between dwc3_suspend() and pm_suspend() of its parent
device, PM suspend will be canceled and attempt to resume suspended
devices so that dwc3_resume() will be called. However, dwc3 and its
parent device (like the power domain or glue driver) may already be
suspended by runtime PM in fact. If this sutiation happened, the
pm_runtime_set_active() in dwc3_resume() will return an error since
parent device was suspended. This can lead to unexpected behavior if
DWC3 proceeds to execute dwc3_resume_common().
EX.
RPM suspend: ... -> dwc3_runtime_suspend()
-> rpm_suspend() of parent device
...
PM suspend: ... -> dwc3_suspend() -> pm_suspend of parent device
^ interrupt, so resume suspended device
... <- dwc3_resume() <-/
^ pm_runtime_set_active() returns error
To prevent the problem, this commit will skip dwc3_resume_common() and
return the error if pm_runtime_set_active() fails.
Fixes: 68c26fe581 ("usb: dwc3: set pm runtime active before resume common")
Cc: stable <stable@kernel.org>
Signed-off-by: Ray Chi <raychi@google.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250106082240.3822059-1-raychi@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This structure isn't used outside this file and can be marked const so
that it gets moved to read-only memory.
Cc: Pavan Holla <pholla@chromium.org>
Cc: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Cc: Łukasz Bartosik <ukaszb@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Łukasz Bartosik <ukaszb@chromium.org>
Link: https://lore.kernel.org/r/20250109220655.1677506-3-swboyd@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Match the locking order used by the core block code by only freezing
the queue after taking the limits lock using the
queue_limits_commit_update_frozen helper.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Nilay Shroff <nilay@linux.ibm.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20250110054726.1499538-10-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Here are some new modem and cp210x device ids.
All have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCZ4EjZAAKCRALxc3C7H1l
CESsAQDHu+J6v93wA+pC62aKYY3kYaf7tRFI8sL+TyoG3GJnLwD/enxl0eg8JBsT
fBejnDz1KG8xcspkaAvoMHOfii2Qhww=
=0r69
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-6.13-rc7' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial device ids for 6.13-rc7
Here are some new modem and cp210x device ids.
All have been in linux-next with no reported issues.
* tag 'usb-serial-6.13-rc7' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add Neoway N723-EA support
USB: serial: option: add MeiG Smart SRM815
USB: serial: cp210x: add Phoenix Contact UPS Device
kthread_create() creates a kthread without running it yet. kthread_run()
creates a kthread and runs it.
On the other hand, kthread_create_worker() creates a kthread worker and
runs it.
This difference in behaviours is confusing. Also there is no way to
create a kthread worker and affine it using kthread_bind_mask() or
kthread_affine_preferred() before starting it.
Consolidate the behaviours and introduce kthread_run_worker[_on_cpu]()
that behaves just like kthread_run(). kthread_create_worker[_on_cpu]()
will now only create a kthread worker without starting it.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Use Linux fix-width types consistently and drop a related unnecessary
cast.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
This adds support for enabling and disabling RTS/CTS hardware flow
control.
Tested using CH341A and CH340E.
Fixes part of the following bug report:
Link: https://bugzilla.kernel.org/show_bug.cgi?id=197109
Signed-off-by: Lode Willems <me@lodewillems.com>
[ johan: prepare index argument once, drop casts ]
Signed-off-by: Johan Hovold <johan@kernel.org>
The error handling for the case `con_index == 0` should involve dropping
the pm usage counter, as ucsi_ccg_sync_control() gets it at the
beginning. Fix it.
Cc: stable <stable@kernel.org>
Fixes: e56aac6e5a ("usb: typec: fix potential array underflow in ucsi_ccg_sync_control()")
Signed-off-by: GONG Ruiqi <gongruiqi1@huawei.com>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250107015750.2778646-1-gongruiqi1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes data corruption when accessing the internal SD card in mass
storage mode.
I am actually not too sure why. I didn't figure a straightforward way to
reproduce the issue, but i seem to get garbage when issuing a lot (over 50)
of large reads (over 120 sectors) are done in a quick succession. That is,
time seems to matter here -- larger reads are fine if they are done with
some delay between them.
But I'm not great at understanding this sort of things, so I'll assume
the issue other, smarter, folks were seeing with similar phones is the
same problem and I'll just put my quirk next to theirs.
The "Software details" screen on the phone is as follows:
V 04.06
07-08-13
RM-849
(c) Nokia
TL;DR version of the device descriptor:
idVendor 0x0421 Nokia Mobile Phones
idProduct 0x06c2
bcdDevice 4.06
iManufacturer 1 Nokia
iProduct 2 Nokia 208
The patch assumes older firmwares are broken too (I'm unable to test, but
no biggie if they aren't I guess), and I have no idea if newer firmware
exists.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Cc: stable <stable@kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20250101212206.2386207-1-lkundrak@v3.sk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should do reverse selection of other components from
CONFIG_USB_F_MIDI2 which is tristate, instead of
CONFIG_USB_CONFIGFS_F_MIDI2 which is bool, for satisfying subtle
module dependencies.
Fixes: 8b645922b2 ("usb: gadget: Add support for USB MIDI 2.0 function driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20250101131124.27599-1-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cable_match(), as matching function of device_find_child(), matches
a device with device type @typec_cable_dev_type, and its task can be
simplified by the recently introduced API device_match_type().
partner_match() is similar with cable_match() but with a different
device type @typec_partner_dev_type.
Remove both functions and use the API plus respective device type instead.
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20241224-const_dfc_done-v5-12-6623037414d4@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Constify the following API:
struct device *device_find_child(struct device *dev, void *data,
int (*match)(struct device *dev, void *data));
To :
struct device *device_find_child(struct device *dev, const void *data,
device_match_t match);
typedef int (*device_match_t)(struct device *dev, const void *data);
with the following reasons:
- Protect caller's match data @*data which is for comparison and lookup
and the API does not actually need to modify @*data.
- Make the API's parameters (@match)() and @data have the same type as
all of other device finding APIs (bus|class|driver)_find_device().
- All kinds of existing device match functions can be directly taken
as the API's argument, they were exported by driver core.
Constify the API and adapt for various existing usages.
BTW, various subsystem changes are squashed into this commit to meet
'git bisect' requirement, and this commit has the minimal and simplest
changes to complement squashing shortcoming, and that may bring extra
code improvement.
Reviewed-by: Alison Schofield <alison.schofield@intel.com>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Uwe Kleine-König <ukleinek@kernel.org> # for drivers/pwm
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20241224-const_dfc_done-v5-4-6623037414d4@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implementation of a UCSI transport driver for ChromeOS.
This driver will be loaded if the ChromeOS EC implements a PPM.
Signed-off-by: Pavan Holla <pholla@chromium.org>
Co-developed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Co-developed-by: Łukasz Bartosik <ukaszb@chromium.org>
Signed-off-by: Łukasz Bartosik <ukaszb@chromium.org>
Link: https://lore.kernel.org/r/20241231131047.1757434-3-ukaszb@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'vbus-supply' regulator is optional, so use
devm_regulator_get_optional() instead of checking for property presence
first.
While here, rework the error handling to use dev_err_probe() which
handles deferred probe correctly without an error message.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20241231164456.262581-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xHC hosts can pass 24 bits of data with a command completion event TRB
as the completion code only uses 8 bits of the 32 bit status field.
Only Configure Endpoint, and Get Extended Property commands utilize
this "command completion parameter" 24 bit field.
For other command completion events the xHC should keep it RsvdZ.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241227120142.1035206-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a command is queued to the final usable TRB of a ring segment, the
enqueue pointer is advanced to the subsequent link TRB and no further.
If the command is later aborted, when the abort completion is handled
the dequeue pointer is advanced to the first TRB of the next segment.
If no further commands are queued, xhci_handle_stopped_cmd_ring() sees
the ring pointers unequal and assumes that there is a pending command,
so it calls xhci_mod_cmd_timer() which crashes if cur_cmd was NULL.
Don't attempt timer setup if cur_cmd is NULL. The subsequent doorbell
ring likely is unnecessary too, but it's harmless. Leave it alone.
This is probably Bug 219532, but no confirmation has been received.
The issue has been independently reproduced and confirmed fixed using
a USB MCU programmed to NAK the Status stage of SET_ADDRESS forever.
Everything continued working normally after several prevented crashes.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=219532
Fixes: c311e391a7 ("xhci: rework command timeout and cancellation,")
CC: stable@vger.kernel.org
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241227120142.1035206-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Improve dbc transfer rate performance by copying the received data to
the tty buffer directly in the request complete callback function if
possible.
Only defer it in case there is already pending deferred work, tty is
throttled, or we fail copy the data to the tty buffer
The request complete callback is already called by a workqueue.
This is part 3/3 of a dbc performance improvement series that roughly
triples dbc performace when using adb push and pull over dbc.
Max/min push rate after patches is 210/118 MB/s, pull rate 171/133 MB/s,
tested with large files (300MB-9GB) by Łukasz Bartosik
Cc: Łukasz Bartosik <ukaszb@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241227120142.1035206-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Queue event polling work with 0 delay in case there are pending transfers
queued up. This is part 2 of a 3 part series that roughly triples dbc
performace when using adb push and pull over dbc.
Max/min push rate after patches is 210/118 MB/s, pull rate 171/133 MB/s,
tested with large files (300MB-9GB) by Łukasz Bartosik
First performance improvement patch was commit 31128e7492
("xhci: dbc: add dbgtty request to end of list once it completes")
Cc: Łukasz Bartosik <ukaszb@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241227120142.1035206-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set TARGET_SCF_ACK_KREF flag and allow f_tcm to take the BOT command
reference. A usb request may be canceled, the f_tcm knows this. Let it
decides if the command should be freed. This is the same as how the UAS
interface is done.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/e791c639e91b5d91a8787f5d6902e8c58f1dc172.1733876548.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Handle target_core_fabric_ops TASK MANAGEMENT functions and their
response. If a TASK MANAGEMENT command is received, the driver will
interpret the function TMF_*, translate to TMR_*, and fire off a command
work executing target_submit_tmr(). On completion, it will handle the
TASK MANAGEMENT response through uasp_send_tm_response().
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/50339586e36509dadb9c208b3314530993e673b6.1733876548.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the transfer is cancelled due to a disconnect or driver tear down
(error code -ESHUTDOWN), then just free the command. However, if it got
cancelled due to other reasons, then send a sense CHECK CONDITION status
with TCM_CHECK_CONDITION_ABORT_CMD status to host notifying the delivery
failure. Note that this is separate from TASK MANAGEMENT function abort
task command, which will require a separate response IU.
See UAS-r04 section 8.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/f2ae293c1fc39df4d242a2f724584bf4ec105ece.1733876548.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There may be different reasons for the transfer to be cancelled. Don't
blindly free the command without checking its status. We may still need
to properly respond to cancelled command. Check and only free the
command on endpoint disable.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/6c4ae2b4c2a9037bdcb6f909e173a94b11f04657.1733876548.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't just wait for the data write completion and execute the target
command. We need to verify if the request completed successfully and not
just sending invalid data. The verification is done in the write request
completion routine. Queue the same work of the command to execute the
target_execute_cmd() on data write.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/9f6b1c6946cf49eeba0173e405678b9b7786636b.1733876548.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To properly respond to host sending more commands than the number of
streams the device advertises, the device needs to be able to reject the
command with a response. Allocate an extra request to handle 1 more
command than the number of streams.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/256f2ec8f5e042ab692d9593144fa75f3d3ce94b.1733876548.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Resubmit command on completion to fetch more commands and service them
in parallel. Increase the number of work in a queue. Each work will be
for each command allowing them to be processed concurrently. Also, set
them to be unbounded by cpu to improve performance.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/933cf7191b672bf4cfbea4df19af1b08dc1baca9.1733876548.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can handle multiple commands concurently. Each command services a
stream id. At the moment, the driver will handle 32 outstanding streams,
which is equivalent to 32 commands. Make sure to allocate a matching
number of commands to the number of streams.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/2d806120dcc10c88fef21865b7bc1d2b6604fe42.1733876548.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Host can assign stream ID value greater than number of streams
allocated. The tcm function needs to keep track of which stream is
available to assign the stream ID. This patch doesn't track that, but at
least it makes sure that there's no Oops if the host send tag with a
value greater than the number of supported streams.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/d57b7dfd228199cef811206b1b83ec649f742752.1733876548.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only allocate up to UASP_SS_EP_COMP_NUM_STREAMS number of session tags.
We should not be using more than UASP_SS_EP_COMP_NUM_STREAMS of tags due
to the number of commands limit we imposed. Each command uses a unique
tag. Any more than that is unnecessary. By limiting it, we can detect an
issue in our driver immediately should we run out of session tags.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/017016ffcab2f3c284d863fc42483b83dbd21b35.1733876548.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the default bMaxBurst is 0. Set default bMaxBurst to 15 (i.e.
16 bursts) to Data IN and OUT endpoints to improve performance. It
should be fine for a controller that supports less than 16 bursts. It
should be able to negotiate properly with the host at packet level for
the end of burst.
If the controller can't handle a burst of 16, and high performance isn't
important, the user can use BOT protocol from mass_storage gadget driver
instead.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/9d6265db4d138e542f281988362bc4392b034d43.1733876548.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some old builds of Microsoft Windows 10 UASP class driver reject UASP
device with stream count of 2^4. To keep compatibility with both Linux
and Windows, let's increase the stream count to 2^5. Also, internal
tests show that stream count of 2^5 increases performance slightly.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/23bf7f5cb04da691fd6ba0a77babee9ad3195f44.1733876548.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The active property of port altmode should be writable (to prevent or
allow partner altmodes from entering) and needs to be part of
typec_altmode_desc so we can initialize the port to an inactive state if
desired.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Link: https://lore.kernel.org/r/20241213153543.v5.3.I794566684ab2965e209f326b08232006eff333f8@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mode in struct typec_altmode is used to indicate the index of the
altmode on a port, partner or plug. It is used in enter mode VDMs but
doesn't make much sense for matching against altmode drivers or for
matching partner to port altmodes.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Link: https://lore.kernel.org/r/20241213153543.v5.1.Ie0d37646f18461234777d88b4c3e21faed92ed4f@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UDC state in sysfs (/sys/class/udc/<udc>/state) should accurately
reflect the current state of the USB Device Controller.
Currently, the UDC state is not handled consistently during gadget
disconnection. While the disconnect interrupt path correctly sets the
state to "not-attached", manual deconfiguration leaves the state in
"configured", misrepresenting the actual situation.
This commit ensures consistent UDC state handling by setting the state to
"not-attached" after manual deconfiguration. This accurately reflects the
UDC's state and provides a consistent behavior regardless of the
disconnection method.
Signed-off-by: Roy Luo <royluo@google.com>
Reviewed-by: André Draszik <andre.draszik@linaro.org>
Tested-by: André Draszik <andre.draszik@linaro.org>
Link: https://lore.kernel.org/r/20241223042536.1465299-1-royluo@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sysfs core now allows instances of 'struct bin_attribute' to be
moved into read-only memory. Make use of that to protect them against
accidental or malicious modifications.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20241222-sysfs-const-bin_attr-usbip-v1-1-20d611a9bfa4@weissschuh.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sysfs core now allows instances of 'struct bin_attribute' to be
moved into read-only memory. Make use of that to protect them against
accidental or malicious modifications.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20241222-sysfs-const-bin_attr-usb-v1-1-19a137c0f20a@weissschuh.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes issue where memory will fail to be allocated for larger bulk
transfers, ~1 MB or more. This occurs because userland libraries, such
as libusb, send the entire USB data buffer when SG support is detected.
The assumption is that the driver knows how to properly split the data
up before sending it out.
By hardcoding a limit, bigger transfers that exceed the SG tablesize
limit of 32 will be unable to use SG. This results in an attempt to
allocate contiguous pages which, unsurprisingly, will fail too and
returns an ENOMEM. It looks like other drivers that support SG allow for
any length of SG lists. Accepting any SG size allows the driver to
properly handle large bulk transfer situations.
Tested bulk read and write operations using the following devices:
- Logitech Webcam Pro 9000 - USB 2.0
- SanDisk Ultra - USB 3.0
- Logitech M500s Mouse
Signed-off-by: Jason Long <jasonlongball@gmail.com>
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20241218161344.202637-1-jasonlongball@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds a new AMS for responding to a "Get_Revision" request.
Revision message consists of the following fields:
+----------------------------------------------------+
| Header | RMDO |
| No. of data objects = 1 | |
+----------------------------------------------------+
While RMDO consists of:
* B31..28 Revision Major
* B27..24 Revision Minor
* B23..20 Version Major
* B19..16 Version Minor
* B15..0 Reserved, shall be set to zero.
As per the PD spec ("8.3.3.16.2.1 PR_Give_Revision State"), a request is
only expected when an explicit contract is established and the port is
in ready state. This AMS is only supported for PD >= 3.0.
Signed-off-by: Amit Sunil Dhamne <amitsd@google.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20241210-get_rev_upstream-v2-3-d0094e52d48f@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for parsing "pd-revision" DT property in TCPM and store PD
revision and version supported by the Type-C connnector.
It should be noted that the PD revision is the maximum possible revision
supported by the port. This is different from the 2 bit revision set in
PD msg headers. The purpose of the 2 bit revision value is to negotiate
between Rev 2.X & 3.X spec rev as part of contract negotiation, while
this is used for Get_Revision AMS after a contract is in place.
Signed-off-by: Amit Sunil Dhamne <amitsd@google.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20241210-get_rev_upstream-v2-2-d0094e52d48f@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TI HD3SS3220 Type-C controller supports configuring
its role preference when operating as a dual-role port
through the SOURCE_PREF field of the General Control Register.
The previous driver behavior was to set the role preference
based on the dr_set typec_operation.
However, the controller does not support swapping the data role
on an active connection due to its lack of Power Delivery support.
Remove previous dr_set typec_operation, and support setting
the role preference based on the corresponding fwnode property,
as well as the try_role typec_operation.
Signed-off-by: Oliver Facklam <oliver.facklam@zuehlke.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20241211-usb-typec-controller-enhancements-v3-3-e4bc1b6e1441@zuehlke.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TI HD3SS3220 Type-C controller supports configuring the port type
it will operate as through the MODE_SELECT field of the General
Control Register.
Configure the port type based on the fwnode property "power-role"
during probe, if present. If the property is absent, leave the
operation mode at the default, which is defined by the PORT pin
of the chip.
Support configuring the port type through the port_type_set
typec_operation as well.
The MODE_SELECT field can only be changed when the controller is in
unattached state, so follow the sequence recommended by the datasheet to:
1. disable termination on CC pins to disable the controller
2. change the mode
3. re-enable termination
This will effectively cause a connected device to disconnect
for the duration of the mode change.
Signed-off-by: Oliver Facklam <oliver.facklam@zuehlke.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20241211-usb-typec-controller-enhancements-v3-2-e4bc1b6e1441@zuehlke.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TI HD3SS3220 Type-C controller supports configuring its advertised
power operation mode over I2C using the CURRENT_MODE_ADVERTISE field
of the Connection Status Register.
Configure this power mode based on the existing (optional) property
"typec-power-opmode" of /schemas/connector/usb-connector.yaml
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Oliver Facklam <oliver.facklam@zuehlke.com>
Link: https://lore.kernel.org/r/20241211-usb-typec-controller-enhancements-v3-1-e4bc1b6e1441@zuehlke.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit addresses an issue related to below kernel panic where
panic_on_warn is enabled. It is caused by the unnecessary use of WARN_ON
in functionsfs_bind, which easily leads to the following scenarios.
1.adb_write in adbd 2. UDC write via configfs
================= =====================
->usb_ffs_open_thread() ->UDC write
->open_functionfs() ->configfs_write_iter()
->adb_open() ->gadget_dev_desc_UDC_store()
->adb_write() ->usb_gadget_register_driver_owner
->driver_register()
->StartMonitor() ->bus_add_driver()
->adb_read() ->gadget_bind_driver()
<times-out without BIND event> ->configfs_composite_bind()
->usb_add_function()
->open_functionfs() ->ffs_func_bind()
->adb_open() ->functionfs_bind()
<ffs->state !=FFS_ACTIVE>
The adb_open, adb_read, and adb_write operations are invoked from the
daemon, but trying to bind the function is a process that is invoked by
UDC write through configfs, which opens up the possibility of a race
condition between the two paths. In this race scenario, the kernel panic
occurs due to the WARN_ON from functionfs_bind when panic_on_warn is
enabled. This commit fixes the kernel panic by removing the unnecessary
WARN_ON.
Kernel panic - not syncing: kernel: panic_on_warn set ...
[ 14.542395] Call trace:
[ 14.542464] ffs_func_bind+0x1c8/0x14a8
[ 14.542468] usb_add_function+0xcc/0x1f0
[ 14.542473] configfs_composite_bind+0x468/0x588
[ 14.542478] gadget_bind_driver+0x108/0x27c
[ 14.542483] really_probe+0x190/0x374
[ 14.542488] __driver_probe_device+0xa0/0x12c
[ 14.542492] driver_probe_device+0x3c/0x220
[ 14.542498] __driver_attach+0x11c/0x1fc
[ 14.542502] bus_for_each_dev+0x104/0x160
[ 14.542506] driver_attach+0x24/0x34
[ 14.542510] bus_add_driver+0x154/0x270
[ 14.542514] driver_register+0x68/0x104
[ 14.542518] usb_gadget_register_driver_owner+0x48/0xf4
[ 14.542523] gadget_dev_desc_UDC_store+0xf8/0x144
[ 14.542526] configfs_write_iter+0xf0/0x138
Fixes: ddf8abd259 ("USB: f_fs: the FunctionFS driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Akash M <akash.m5@samsung.com>
Link: https://lore.kernel.org/r/20241219125221.1679-1-akash.m5@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's USB error when tegra board is shutting down:
[ 180.919315] usb 2-3: Failed to set U1 timeout to 0x0,error code -113
[ 180.919995] usb 2-3: Failed to set U1 timeout to 0xa,error code -113
[ 180.920512] usb 2-3: Failed to set U2 timeout to 0x4,error code -113
[ 186.157172] tegra-xusb 3610000.usb: xHCI host controller not responding, assume dead
[ 186.157858] tegra-xusb 3610000.usb: HC died; cleaning up
[ 186.317280] tegra-xusb 3610000.usb: Timeout while waiting for evaluate context command
The issue is caused by disabling LPM on already suspended ports.
For USB2 LPM, the LPM is already disabled during port suspend. For USB3
LPM, port won't transit to U1/U2 when it's already suspended in U3,
hence disabling LPM is only needed for ports that are not suspended.
Cc: Wayne Chang <waynec@nvidia.com>
Cc: stable <stable@kernel.org>
Fixes: d920a2ed86 ("usb: Disable USB3 LPM at shutdown")
Signed-off-by: Kai-Heng Feng <kaihengf@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20241206074817.89189-1-kaihengf@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When device_add(&udev->dev) succeeds and a later call fails,
usb_new_device() does not properly call device_del(). As comment of
device_add() says, 'if device_add() succeeds, you should call
device_del() when you want to get rid of it. If device_add() has not
succeeded, use only put_device() to drop the reference count'.
Found by code review.
Cc: stable <stable@kernel.org>
Fixes: 9f8b17e643 ("USB: make usbdevices export their device nodes instead of using a separate class")
Signed-off-by: Ma Ke <make_ruc2021@163.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20241218071346.2973980-1-make_ruc2021@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tcpci_irq() may meet below NULL pointer dereference issue:
[ 2.641851] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000010
[ 2.641951] status 0x1, 0x37f
[ 2.650659] Mem abort info:
[ 2.656490] ESR = 0x0000000096000004
[ 2.660230] EC = 0x25: DABT (current EL), IL = 32 bits
[ 2.665532] SET = 0, FnV = 0
[ 2.668579] EA = 0, S1PTW = 0
[ 2.671715] FSC = 0x04: level 0 translation fault
[ 2.676584] Data abort info:
[ 2.679459] ISV = 0, ISS = 0x00000004, ISS2 = 0x00000000
[ 2.684936] CM = 0, WnR = 0, TnD = 0, TagAccess = 0
[ 2.689980] GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0
[ 2.695284] [0000000000000010] user address but active_mm is swapper
[ 2.701632] Internal error: Oops: 0000000096000004 [#1] PREEMPT SMP
[ 2.707883] Modules linked in:
[ 2.710936] CPU: 1 UID: 0 PID: 87 Comm: irq/111-2-0051 Not tainted 6.12.0-rc6-06316-g7f63786ad3d1-dirty #4
[ 2.720570] Hardware name: NXP i.MX93 11X11 EVK board (DT)
[ 2.726040] pstate: 60400009 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 2.732989] pc : tcpci_irq+0x38/0x318
[ 2.736647] lr : _tcpci_irq+0x14/0x20
[ 2.740295] sp : ffff80008324bd30
[ 2.743597] x29: ffff80008324bd70 x28: ffff800080107894 x27: ffff800082198f70
[ 2.750721] x26: ffff0000050e6680 x25: ffff000004d172ac x24: ffff0000050f0000
[ 2.757845] x23: ffff000004d17200 x22: 0000000000000001 x21: ffff0000050f0000
[ 2.764969] x20: ffff000004d17200 x19: 0000000000000000 x18: 0000000000000001
[ 2.772093] x17: 0000000000000000 x16: ffff80008183d8a0 x15: ffff00007fbab040
[ 2.779217] x14: ffff00007fb918c0 x13: 0000000000000000 x12: 000000000000017a
[ 2.786341] x11: 0000000000000001 x10: 0000000000000a90 x9 : ffff80008324bd00
[ 2.793465] x8 : ffff0000050f0af0 x7 : ffff00007fbaa840 x6 : 0000000000000031
[ 2.800589] x5 : 000000000000017a x4 : 0000000000000002 x3 : 0000000000000002
[ 2.807713] x2 : ffff80008324bd3a x1 : 0000000000000010 x0 : 0000000000000000
[ 2.814838] Call trace:
[ 2.817273] tcpci_irq+0x38/0x318
[ 2.820583] _tcpci_irq+0x14/0x20
[ 2.823885] irq_thread_fn+0x2c/0xa8
[ 2.827456] irq_thread+0x16c/0x2f4
[ 2.830940] kthread+0x110/0x114
[ 2.834164] ret_from_fork+0x10/0x20
[ 2.837738] Code: f9426420 f9001fe0 d2800000 52800201 (f9400a60)
This may happen on shared irq case. Such as two Type-C ports share one
irq. After the first port finished tcpci_register_port(), it may trigger
interrupt. However, if the interrupt comes by chance the 2nd port finishes
devm_request_threaded_irq(), the 2nd port interrupt handler will run at
first. Then the above issue happens due to tcpci is still a NULL pointer
in tcpci_irq() when dereference to regmap.
devm_request_threaded_irq()
<-- port1 irq comes
disable_irq(client->irq);
tcpci_register_port()
This will restore the logic to the state before commit (77e85107a7 "usb:
typec: tcpci: support edge irq").
However, moving tcpci_register_port() earlier creates a problem when use
edge irq because tcpci_init() will be called before
devm_request_threaded_irq(). The tcpci_init() writes the ALERT_MASK to
the hardware to tell it to start generating interrupts but we're not ready
to deal with them yet, then the ALERT events may be missed and ALERT line
will not recover to high level forever. To avoid the issue, this will also
set ALERT_MASK register after devm_request_threaded_irq() return.
Fixes: 77e85107a7 ("usb: typec: tcpci: support edge irq")
Cc: stable <stable@kernel.org>
Tested-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/20241218095328.2604607-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Considering that in some extreme cases, when performing the
unbinding operation, gserial_disconnect has cleared gser->ioport,
which triggers gadget reconfiguration, and then calls gs_read_complete,
resulting in access to a null pointer. Therefore, ep is disabled before
gserial_disconnect sets port to null to prevent this from happening.
Call trace:
gs_read_complete+0x58/0x240
usb_gadget_giveback_request+0x40/0x160
dwc3_remove_requests+0x170/0x484
dwc3_ep0_out_start+0xb0/0x1d4
__dwc3_gadget_start+0x25c/0x720
kretprobe_trampoline.cfi_jt+0x0/0x8
kretprobe_trampoline.cfi_jt+0x0/0x8
udc_bind_to_driver+0x1d8/0x300
usb_gadget_probe_driver+0xa8/0x1dc
gadget_dev_desc_UDC_store+0x13c/0x188
configfs_write_iter+0x160/0x1f4
vfs_write+0x2d0/0x40c
ksys_write+0x7c/0xf0
__arm64_sys_write+0x20/0x30
invoke_syscall+0x60/0x150
el0_svc_common+0x8c/0xf8
do_el0_svc+0x28/0xa0
el0_svc+0x24/0x84
Fixes: c1dca562be ("usb gadget: split out serial core")
Cc: stable <stable@kernel.org>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Lianqin Hu <hulianqin@vivo.com>
Link: https://lore.kernel.org/r/TYUPR06MB621733B5AC690DBDF80A0DCCD2042@TYUPR06MB6217.apcprd06.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current implementation of ci_hdrc_imx_driver does not decrement the
refcount of the device obtained in usbmisc_get_init_data(). Add a
put_device() call in .remove() and in .probe() before returning an
error.
This bug was found by an experimental static analysis tool that I am
developing.
Cc: stable <stable@kernel.org>
Fixes: f40017e0f3 ("chipidea: usbmisc_imx: Add USB support for VF610 SoCs")
Signed-off-by: Joe Hattori <joe@pf.is.s.u-tokyo.ac.jp>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20241216015539.352579-1-joe@pf.is.s.u-tokyo.ac.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current implementation of the ucsi glink client connector_status()
callback is only relying on the state of the gpio. This means that even
when the cable is unplugged, the orientation propagated to the switches
along the graph is "orientation normal", instead of "orientation none",
which would be the correct one in this case.
One of the Qualcomm DP-USB PHY combo drivers, which needs to be aware of
the orientation change, is relying on the "orientation none" to skip
the reinitialization of the entire PHY. Since the ucsi glink client
advertises "orientation normal" even when the cable is unplugged, the
mentioned PHY is taken down and reinitialized when in fact it should be
left as-is. This triggers a crash within the displayport controller driver
in turn, which brings the whole system down on some Qualcomm platforms.
Propagating "orientation none" from the ucsi glink client on the
connector_status() callback hides the problem of the mentioned PHY driver
away for now. But the "orientation none" is nonetheless the correct one
to be used in this case.
So propagate the "orientation none" instead when the connector status
flags says cable is disconnected.
Fixes: 76716fd5bf ("usb: typec: ucsi: glink: move GPIO reading into connector_status callback")
Cc: stable <stable@kernel.org> # 6.10
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20241212-usb-typec-ucsi-glink-add-orientation-none-v2-1-db5a50498a77@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit c033563220
("usb: gadget: configfs: Attach arbitrary strings to cdev")
a user can provide extra string descriptors to a USB gadget via configfs.
For "manufacturer", "product", "serialnumber", setting the string via
configfs ignores a trailing LF.
For the arbitrary strings the LF was not ignored.
This patch ignores a trailing LF to make this consistent with the existing
behavior for "manufacturer", ... string descriptors.
Fixes: c033563220 ("usb: gadget: configfs: Attach arbitrary strings to cdev")
Cc: stable <stable@kernel.org>
Signed-off-by: Ingo Rohloff <ingo.rohloff@lauterbach.com>
Link: https://lore.kernel.org/r/20241212154114.29295-1-ingo.rohloff@lauterbach.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the regression introduced by commit d8c6edfa3f ("USB:
usblp: don't call usb_set_interface if there's a single alt"),
which causes that unsupported protocols can also be set via
ioctl when the num_altsetting of the device is 1.
Move the check for protocol support to the earlier stage.
Fixes: d8c6edfa3f ("USB: usblp: don't call usb_set_interface if there's a single alt")
Cc: stable <stable@kernel.org>
Signed-off-by: Jun Yan <jerrysteve1101@gmail.com>
Link: https://lore.kernel.org/r/20241212143852.671889-1-jerrysteve1101@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently afunc_bind sets std_ac_if_desc.bNumEndpoints to 1 if
controls (mute/volume) are enabled. During next afunc_bind call,
bNumEndpoints would be unchanged and incorrectly set to 1 even
if the controls aren't enabled.
Fix this by resetting the value of bNumEndpoints to 0 on every
afunc_bind call.
Fixes: eaf6cbe099 ("usb: gadget: f_uac2: add volume and mute support")
Cc: stable <stable@kernel.org>
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Link: https://lore.kernel.org/r/20241211115915.159864-1-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The source of quirk XHCI_SKIP_PHY_INIT comes from xhci_plat_priv.quirks or
software node property. This will set skip_phy_initialization if software
node also has XHCI_SKIP_PHY_INIT property.
Fixes: a6cd2b3fa8 ("usb: host: xhci-plat: Parse xhci-missing_cas_quirk and apply quirk")
Cc: stable <stable@kernel.org>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20241209111423.4085548-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Runtime PM documentation (Section 5) mentions, during remove()
callbacks, drivers should undo the runtime PM changes done in
probe(). Usually this means calling pm_runtime_disable(),
pm_runtime_dont_use_autosuspend() etc. Hence add missing
function to disable autosuspend on dwc3-am62 driver unbind.
Fixes: e8784c0aec ("drivers: usb: dwc3: Add AM62 USB wrapper driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20241209105728.3216872-1-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before writing a new value to the register, the old value needs to be
masked out for the new value to be programmed as intended, because at
least in some cases the reset value of that field is 0xf (max value).
At the moment, the dwc3 core initialises the threshold to the maximum
value (0xf), with the option to override it via a DT. No upstream DTs
seem to override it, therefore this commit doesn't change behaviour for
any upstream platform. Nevertheless, the code should be fixed to have
the desired outcome.
Do so.
Fixes: 80caf7d21a ("usb: dwc3: add lpm erratum support")
Cc: stable@vger.kernel.org # 5.10+ (needs adjustment for 5.4)
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20241209-dwc3-nyet-fix-v2-1-02755683345b@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The cc1 and cc2 status returned by tcpci_get_cc() may be TYPEC_CC_OPEN
or TYPEC_CC_RA. So don't assume it's just TYPEC_CC_RD or TYPEC_CC_RP_*.
This will let local port present Rd on CC only when cc1/cc2 status is
TYPEC_CC_RP_*.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20241211105753.1205312-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If controller looses power during PM suspend then re-initialize
it. We use the DEBUG_CFG register to track if controller lost power
or was reset in PM suspend.
Move all initialization code into dwc3_ti_init() so it can be re-used.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20241212-am62-dwc3-io-ddr-v3-1-10b95cd7e9c0@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds documentation for two USB functions:
- usb_otg_state_string(), which returns a human-readable name for OTG
states and
- usb_get_dr_mode_from_string(), which returns the dual role mode for a
given string.
Signed-off-by: Lucy Mielke <lucymielke@icloud.com>
Link: https://lore.kernel.org/r/6nvegfmo6d5ak4soaf5nyifsaasfts4qlsnnpsd4sgpnikc2jd@amfmgdr5n3bi
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the function pmc_mux_port_debugfs_init() the buffer for
the name of the port is limited to six bytes. That makes the
compiler think that the output of "port%d" may be truncated.
That can't actually happen as the interface can support
maximum of eight ports. To make the compiler happy just
increase the buffer to where the warning goes away.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202412031437.vX580pxx-lkp@intel.com/
Cc: Rajat Khandelwal <rajat.khandelwal@linux.intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20241205113919.1182673-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It generally is not OK to use acpi_status and/or AE_ error codes
without CONFIG_ACPI and they really only should be used in
drivers/acpi/ (and not everywhere in there for that matter).
So acpi_get_physical_device_location() needs to be redefined to return
something different from acpi_status (preferably bool) in order to be
used in !CONFIG_ACPI code.
Suggested-by: Rafael J. Wysocki <rafael@kernel.org>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Link: https://patch.msgid.link/20241216-fix-ipu-v5-1-3d6b35ddce7b@chromium.org
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The source and destination rings were incorrectly assigned during the ring
linking process. The "source" ring, which contains the new segments,
was not spliced into the "destination" ring, leading to incorrect ring
expansion.
Fixes: fe688e5006 ("usb: xhci: refactor xhci_link_rings() to use source and destination rings")
Reported-by: Jeff Chua <jeff.chua.linux@gmail.com>
Closes: https://lore.kernel.org/lkml/CAAJw_ZtppNqC9XA=-WVQDr+vaAS=di7jo15CzSqONeX48H75MA@mail.gmail.com/
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241217102122.2316814-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xHC hosts from several vendors have the same issue where endpoints start
so slowly that a later queued 'Stop Endpoint' command may complete before
endpoint is up and running.
The 'Stop Endpoint' command fails with context state error as the endpoint
still appears as stopped.
See commit 42b7581376 ("usb: xhci: Limit Stop Endpoint retries") for
details
CC: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241217102122.2316814-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some new modem device ids.
All have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCZ1vuXQAKCRALxc3C7H1l
CLJ0AQDSkSckl0A6kriR/xOSDWv2uIC+insL1LC5njr/JJrv7wD/WoRWIHEllqVN
JLdKbJ2Vim+2BG16DsW8/mpVldkaLAY=
=wuzL
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-6.13-rc3' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial device ids for 6.13-rc3
Here are some new modem device ids.
All have been in linux-next with no reported issues.
* tag 'usb-serial-6.13-rc3' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add Telit FE910C04 rmnet compositions
USB: serial: option: add MediaTek T7XX compositions
USB: serial: option: add Netprisma LCUK54 modules for WWAN Ready
USB: serial: option: add MeiG Smart SLM770A
USB: serial: option: add TCL IK512 MBIM & ECM
Here are some small USB driver fixes for some reported issues. Included
in here are:
- typec driver bugfixes
- u_serial gadget driver bugfix for much reported and discussed issue
- dwc2 bugfixes
- midi gadget driver bugfix
- ehci-hcd driver bugfix
- other small bugfixes
All of these have been in linux-next for over a week with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZ12Wwg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymbWgCeKUCeGFlUanDHY1nHq72FSMiHpcUAoIvzBTx1
yUEhvtuYYZ/NBzfKI+8h
=WeQD
-----END PGP SIGNATURE-----
Merge tag 'usb-6.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB driver fixes from Greg KH:
"Here are some small USB driver fixes for some reported issues.
Included in here are:
- typec driver bugfixes
- u_serial gadget driver bugfix for much reported and discussed issue
- dwc2 bugfixes
- midi gadget driver bugfix
- ehci-hcd driver bugfix
- other small bugfixes
All of these have been in linux-next for over a week with no reported
issues"
* tag 'usb-6.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: typec: ucsi: Fix connector status writing past buffer size
usb: typec: ucsi: Fix completion notifications
usb: dwc2: Fix HCD port connection race
usb: dwc2: hcd: Fix GetPortStatus & SetPortFeature
usb: dwc2: Fix HCD resume
usb: gadget: u_serial: Fix the issue that gs_start_io crashed due to accessing null pointer
usb: misc: onboard_usb_dev: skip suspend/resume sequence for USB5744 SMBus support
usb: dwc3: xilinx: make sure pipe clock is deselected in usb2 only mode
usb: core: hcd: only check primary hcd skip_phy_initialization
usb: gadget: midi2: Fix interpretation of is_midi1 bits
usb: dwc3: imx8mp: fix software node kernel dump
usb: typec: anx7411: fix OF node reference leaks in anx7411_typec_switch_probe()
usb: typec: anx7411: fix fwnode_handle reference leak
usb: host: max3421-hcd: Correctly abort a USB request.
dt-bindings: phy: imx8mq-usb: correct reference to usb-switch.yaml
usb: ehci-hcd: fix call balance of clocks handling routines
Improve naming consistency with the .sdev_prep() and .sdev_destroy()
methods by renaming .device_configure() into .sdev_configure().
Cc: Christoph Hellwig <hch@lst.de>
Acked-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20241022180839.2712439-3-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Rename .slave_alloc() into .sdev_init() and .slave_destroy() into
.sdev_destroy(). The new names make it clear that these are actions on
SCSI devices. Make this change in the SCSI core, SCSI drivers and also
in the ATA drivers. No functionality has been changed.
This patch has been created as follows:
* Change the text "slave_alloc" into "sdev_init" in all source files
except those in drivers/net/ and Documentation/.
* Change the text "slave_destroy" into "sdev_destroy" in all source
files except those in drivers/net/ and Documentation/.
* Rename lpfc_no_slave() into lpfc_no_sdev().
* Manually adjust whitespace where necessary to restore vertical
alignment (dc395x driver and include/linux/libata.h).
Acked-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20241022180839.2712439-2-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The meaning of this value is already used in several places,
but with constant values and comments to explain it separately.
It's better to have a central place to do this then use the macro
in those places for better readability.
Signed-off-by: Dingyan Li <18500469033@163.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20241030083858.46907-1-18500469033@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
OPM PPM LPM
| 1.send cmd | |
|-------------------------->| |
| |-- |
| | | 2.set busy bit in CCI |
| |<- |
| 3.notify the OPM | |
|<--------------------------| |
| | 4.send cmd to be executed |
| |-------------------------->|
| | |
| | 5.cmd completed |
| |<--------------------------|
| | |
| |-- |
| | | 6.set cmd completed |
| |<- bit in CCI |
| | |
| 7.notify the OPM | |
|<--------------------------| |
| | |
| 8.handle notification | |
| from point 3, read CCI | |
|<--------------------------| |
| | |
When the PPM receives command from the OPM (p.1) it sets the busy bit
in the CCI (p.2), sends notification to the OPM (p.3) and forwards the
command to be executed by the LPM (p.4). When the PPM receives command
completion from the LPM (p.5) it sets command completion bit in the CCI
(p.6) and sends notification to the OPM (p.7). If command execution by
the LPM is fast enough then when the OPM starts handling the notification
from p.3 in p.8 and reads the CCI value it will see command completion bit
set and will call complete(). Then complete() might be called again when
the OPM handles notification from p.7.
This fix replaces test_bit() with test_and_clear_bit()
in ucsi_notify_common() in order to call complete() only
once per request.
This fix also reinitializes completion variable in
ucsi_sync_control_common() before a command is sent.
Fixes: 584e8df589 ("usb: typec: ucsi: extract common code for command handling")
Cc: stable@vger.kernel.org
Signed-off-by: Łukasz Bartosik <ukaszb@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Link: https://lore.kernel.org/r/20241203102318.3386345-1-ukaszb@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On Raspberry Pis without onboard USB hub frequent device reconnects
can trigger a interrupt storm after DWC2 entered host clock gating.
This is caused by a race between _dwc2_hcd_suspend() and the port
interrupt, which sets port_connect_status. The issue occurs if
port_connect_status is still 1, but there is no connection anymore:
usb 1-1: USB disconnect, device number 25
dwc2 3f980000.usb: _dwc2_hcd_suspend: port_connect_status: 1
dwc2 3f980000.usb: Entering host clock gating.
Disabling IRQ #66
irq 66: nobody cared (try booting with the "irqpoll" option)
CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted 6.12.0-gc1bb81b13202-dirty #322
Hardware name: BCM2835
Call trace:
unwind_backtrace from show_stack+0x10/0x14
show_stack from dump_stack_lvl+0x50/0x64
dump_stack_lvl from __report_bad_irq+0x38/0xc0
__report_bad_irq from note_interrupt+0x2ac/0x2f4
note_interrupt from handle_irq_event+0x88/0x8c
handle_irq_event from handle_level_irq+0xb4/0x1ac
handle_level_irq from generic_handle_domain_irq+0x24/0x34
generic_handle_domain_irq from bcm2836_chained_handle_irq+0x24/0x28
bcm2836_chained_handle_irq from generic_handle_domain_irq+0x24/0x34
generic_handle_domain_irq from generic_handle_arch_irq+0x34/0x44
generic_handle_arch_irq from __irq_svc+0x88/0xb0
Exception stack(0xc1d01f20 to 0xc1d01f68)
1f20: 0004ef3c 00000001 00000000 00000000 c1d09780 c1f6bb5c c1d04e54 c1c60ca8
1f40: c1d04e94 00000000 00000000 c1d092a8 c1f6af20 c1d01f70 c1211b98 c1212f40
1f60: 60000013 ffffffff
__irq_svc from default_idle_call+0x1c/0xb0
default_idle_call from do_idle+0x21c/0x284
do_idle from cpu_startup_entry+0x28/0x2c
cpu_startup_entry from kernel_init+0x0/0x12c
handlers:
[<e3a25c00>] dwc2_handle_common_intr
[<58bf98a3>] usb_hcd_irq
Disabling IRQ #66
So avoid this by reading the connection status directly.
Fixes: 113f86d0c3 ("usb: dwc2: Update partial power down entering by system suspend")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/20241202001631.75473-4-wahrenst@gmx.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On Rasperry Pis without onboard USB hub the power cycle during
power connect init only disable the port but never enabled it again:
usb usb1-port1: attempt power cycle
The port relevant part in dwc2_hcd_hub_control() is skipped in case
port_connect_status = 0 under the assumption the core is or will be soon
in device mode. But this assumption is wrong, because after ClearPortFeature
USB_PORT_FEAT_POWER the port_connect_status will also be 0 and
SetPortFeature (incl. USB_PORT_FEAT_POWER) will be a no-op.
Fix the behavior of dwc2_hcd_hub_control() by replacing the
port_connect_status check with dwc2_is_device_mode().
Link: https://github.com/raspberrypi/linux/issues/6247
Fixes: 7359d482eb ("staging: HCD files for the DWC2 driver")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/20241202001631.75473-3-wahrenst@gmx.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Raspberry Pi can suffer on interrupt storms on HCD resume. The dwc2
driver sometimes misses to enable HCD_FLAG_HW_ACCESSIBLE before re-enabling
the interrupts. This causes a situation where both handler ignore a incoming
port interrupt and force the upper layers to disable the dwc2 interrupt
line. This leaves the USB interface in a unusable state:
irq 66: nobody cared (try booting with the "irqpoll" option)
CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W 6.10.0-rc3
Hardware name: BCM2835
Call trace:
unwind_backtrace from show_stack+0x10/0x14
show_stack from dump_stack_lvl+0x50/0x64
dump_stack_lvl from __report_bad_irq+0x38/0xc0
__report_bad_irq from note_interrupt+0x2ac/0x2f4
note_interrupt from handle_irq_event+0x88/0x8c
handle_irq_event from handle_level_irq+0xb4/0x1ac
handle_level_irq from generic_handle_domain_irq+0x24/0x34
generic_handle_domain_irq from bcm2836_chained_handle_irq+0x24/0x28
bcm2836_chained_handle_irq from generic_handle_domain_irq+0x24/0x34
generic_handle_domain_irq from generic_handle_arch_irq+0x34/0x44
generic_handle_arch_irq from __irq_svc+0x88/0xb0
Exception stack(0xc1b01f20 to 0xc1b01f68)
1f20: 0005c0d4 00000001 00000000 00000000 c1b09780 c1d6b32c c1b04e54 c1a5eae8
1f40: c1b04e90 00000000 00000000 00000000 c1d6a8a0 c1b01f70 c11d2da8 c11d4160
1f60: 60000013 ffffffff
__irq_svc from default_idle_call+0x1c/0xb0
default_idle_call from do_idle+0x21c/0x284
do_idle from cpu_startup_entry+0x28/0x2c
cpu_startup_entry from kernel_init+0x0/0x12c
handlers:
[<f539e0f4>] dwc2_handle_common_intr
[<75cd278b>] usb_hcd_irq
Disabling IRQ #66
So enable the HCD_FLAG_HW_ACCESSIBLE flag in case there is a port
connection.
Fixes: c74c26f6e3 ("usb: dwc2: Fix partial power down exiting by system resume")
Closes: https://lore.kernel.org/linux-usb/3fd0c2fb-4752-45b3-94eb-42352703e1fd@gmx.net/T/
Link: https://lore.kernel.org/all/5e8cbce0-3260-2971-484f-fc73a3b2bd28@synopsys.com/
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/20241202001631.75473-2-wahrenst@gmx.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Considering that in some extreme cases,
when u_serial driver is accessed by multiple threads,
Thread A is executing the open operation and calling the gs_open,
Thread B is executing the disconnect operation and calling the
gserial_disconnect function,The port->port_usb pointer will be set to NULL.
E.g.
Thread A Thread B
gs_open() gadget_unbind_driver()
gs_start_io() composite_disconnect()
gs_start_rx() gserial_disconnect()
... ...
spin_unlock(&port->port_lock)
status = usb_ep_queue() spin_lock(&port->port_lock)
spin_lock(&port->port_lock) port->port_usb = NULL
gs_free_requests(port->port_usb->in) spin_unlock(&port->port_lock)
Crash
This causes thread A to access a null pointer (port->port_usb is null)
when calling the gs_free_requests function, causing a crash.
If port_usb is NULL, the release request will be skipped as it
will be done by gserial_disconnect.
So add a null pointer check to gs_start_io before attempting
to access the value of the pointer port->port_usb.
Call trace:
gs_start_io+0x164/0x25c
gs_open+0x108/0x13c
tty_open+0x314/0x638
chrdev_open+0x1b8/0x258
do_dentry_open+0x2c4/0x700
vfs_open+0x2c/0x3c
path_openat+0xa64/0xc60
do_filp_open+0xb8/0x164
do_sys_openat2+0x84/0xf0
__arm64_sys_openat+0x70/0x9c
invoke_syscall+0x58/0x114
el0_svc_common+0x80/0xe0
do_el0_svc+0x1c/0x28
el0_svc+0x38/0x68
Fixes: c1dca562be ("usb gadget: split out serial core")
Cc: stable@vger.kernel.org
Suggested-by: Prashanth K <quic_prashk@quicinc.com>
Signed-off-by: Lianqin Hu <hulianqin@vivo.com>
Acked-by: Prashanth K <quic_prashk@quicinc.com>
Link: https://lore.kernel.org/r/TYUPR06MB62178DC3473F9E1A537DCD02D2362@TYUPR06MB6217.apcprd06.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB5744 SMBus initialization is done once in probe() and doing it in resume
is not supported so avoid going into suspend and reset the HUB.
There is a sysfs property 'always_powered_in_suspend' to implement this
feature but since default state should be set to a working configuration
so override this property value.
It fixes the suspend/resume testcase on Kria KR260 Robotics Starter Kit.
Fixes: 6782311d04 ("usb: misc: onboard_usb_dev: add Microchip usb5744 SMBus programming support")
Cc: stable@vger.kernel.org
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Link: https://lore.kernel.org/r/1733165302-1694891-1-git-send-email-radhey.shyam.pandey@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the USB3 PHY is not defined in the Linux device tree, there could
still be a case where there is a USB3 PHY active on the board and enabled
by the first stage bootloader. If serdes clock is being used then the USB
will fail to enumerate devices in 2.0 only mode.
To solve this, make sure that the PIPE clock is deselected whenever the
USB3 PHY is not defined and guarantees that the USB2 only mode will work
in all cases.
Fixes: 9678f3361a ("usb: dwc3: xilinx: Skip resets and USB3 register settings for USB2.0 mode")
Cc: stable@vger.kernel.org
Signed-off-by: Neal Frager <neal.frager@amd.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Link: https://lore.kernel.org/r/1733163111-1414816-1-git-send-email-radhey.shyam.pandey@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before commit 53a2d95df8 ("usb: core: add phy notify connect and
disconnect"), phy initialization will be skipped even when shared hcd
doesn't set skip_phy_initialization flag. However, the situation is
changed after the commit. The hcd.c will initialize phy when add shared
hcd. This behavior is unexpected for some platforms which will handle phy
initialization by themselves. To avoid the issue, this will only check
skip_phy_initialization flag of primary hcd since shared hcd normally
follow primary hcd setting.
Fixes: 53a2d95df8 ("usb: core: add phy notify connect and disconnect")
Cc: stable@vger.kernel.org
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20241105090120.2438366-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UMP Function Block info m1.0 field (represented by is_midi1 sysfs
entry) is an enumeration from 0 to 2, while the midi2 gadget driver
incorrectly copies it to the corresponding snd_ump_block_info.flags
bits as-is. This made the wrong bit flags set when m1.0 = 2.
This patch corrects the wrong interpretation of is_midi1 bits.
Fixes: 29ee7a4ddd ("usb: gadget: midi2: Add configfs support")
Cc: stable@vger.kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20241127070213.8232-1-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When unbind and bind the device again, kernel will dump below warning:
[ 173.972130] sysfs: cannot create duplicate filename '/devices/platform/soc/4c010010.usb/software_node'
[ 173.981564] CPU: 2 UID: 0 PID: 536 Comm: sh Not tainted 6.12.0-rc6-06344-g2aed7c4a5c56 #144
[ 173.989923] Hardware name: NXP i.MX95 15X15 board (DT)
[ 173.995062] Call trace:
[ 173.997509] dump_backtrace+0x90/0xe8
[ 174.001196] show_stack+0x18/0x24
[ 174.004524] dump_stack_lvl+0x74/0x8c
[ 174.008198] dump_stack+0x18/0x24
[ 174.011526] sysfs_warn_dup+0x64/0x80
[ 174.015201] sysfs_do_create_link_sd+0xf0/0xf8
[ 174.019656] sysfs_create_link+0x20/0x40
[ 174.023590] software_node_notify+0x90/0x100
[ 174.027872] device_create_managed_software_node+0xec/0x108
...
The '4c010010.usb' device is a platform device created during the initcall
and is never removed, which causes its associated software node to persist
indefinitely.
The existing device_create_managed_software_node() does not provide a
corresponding removal function.
Replace device_create_managed_software_node() with the
device_add_software_node() and device_remove_software_node() pair to ensure
proper addition and removal of software nodes, addressing this issue.
Fixes: a9400f1979 ("usb: dwc3: imx8mp: add 2 software managed quirk properties for host mode")
Cc: stable@vger.kernel.org
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20241126032841.2458338-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The refcounts of the OF nodes obtained by of_get_child_by_name() calls
in anx7411_typec_switch_probe() are not decremented. Replace them with
device_get_named_child_node() calls and store the return values to the
newly created fwnode_handle fields in anx7411_data, and call
fwnode_handle_put() on them in the error path and in the unregister
functions.
Fixes: e45d7337dc ("usb: typec: anx7411: Use of_get_child_by_name() instead of of_find_node_by_name()")
Cc: stable@vger.kernel.org
Signed-off-by: Joe Hattori <joe@pf.is.s.u-tokyo.ac.jp>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20241126014909.3687917-1-joe@pf.is.s.u-tokyo.ac.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An fwnode_handle and usb_role_switch are obtained with an incremented
refcount in anx7411_typec_port_probe(), however the refcounts are not
decremented in the error path. The fwnode_handle is also not decremented
in the .remove() function. Therefore, call fwnode_handle_put() and
usb_role_switch_put() accordingly.
Fixes: fe6d8a9c8e ("usb: typec: anx7411: Add Analogix PD ANX7411 support")
Cc: stable@vger.kernel.org
Signed-off-by: Joe Hattori <joe@pf.is.s.u-tokyo.ac.jp>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20241121023429.962848-1-joe@pf.is.s.u-tokyo.ac.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the current USB request was aborted, the spi thread would not respond
to any further requests. This is because the "curr_urb" pointer would
not become NULL, so no further requests would be taken off the queue.
The solution here is to set the "urb_done" flag, as this will cause the
correct handling of the URB. Also clear interrupts that should only be
expected if an URB is in progress.
Fixes: 2d53139f31 ("Add support for using a MAX3421E chip as a host driver.")
Cc: stable <stable@kernel.org>
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20241124221430.1106080-1-mark.tomlinson@alliedtelesis.co.nz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the clocks priv->iclk and priv->fclk were not enabled in ehci_hcd_sh_probe,
they should not be disabled in any path.
Conversely, if they was enabled in ehci_hcd_sh_probe, they must be disabled
in all error paths to ensure proper cleanup.
Found by Linux Verification Center (linuxtesting.org) with Klever.
Fixes: 63c8455222 ("usb: ehci-hcd: Add support for SuperH EHCI.")
Cc: stable@vger.kernel.org # ff30bd6a6618: sh: clk: Fix clk_enable() to return 0 on NULL clk
Signed-off-by: Vitalii Mordan <mordan@ispras.ru>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20241121114700.2100520-1-mordan@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a device is inserted into the USB port and an S4 wakeup is initiated,
after the USB-hub initialization is completed, it will automatically enter
suspend mode. Upon detecting a device on the USB port, it will proceed with
resume and set the hcd to the HCD_FLAG_WAKEUP_PENDING state. During the S4
wakeup process, peripherals are put into suspend mode, followed by task
recovery. However, upon detecting that the hcd is in the
HCD_FLAG_WAKEUP_PENDING state, it will return an EBUSY status, causing the
S4 suspend to fail and subsequent task recovery to not proceed.
-
[ 27.594598][ 1] PM: pci_pm_freeze(): hcd_pci_suspend+0x0/0x28 returns -16
[ 27.594601][ 1] PM: dpm_run_callback(): pci_pm_freeze+0x0/0x100 returns -16
[ 27.603420][ 1] ehci-pci 0000:00:04.1: pci_pm_freeze+0x0/0x100 returned 0 after 3 usecs
[ 27.612233][ 1] ehci-pci 0000:00:05.1: pci_pm_freeze+0x0/0x100 returned -16 after 17223 usecs
[ 27.810067][ 1] PM: Device 0000:00:05.1 failed to quiesce async: error -16
[ 27.816988][ 1] PM: quiesce of devices aborted after 1833.282 msecs
[ 27.823302][ 1] PM: start quiesce of devices aborted after 1839.975 msecs
......
[ 31.303172][ 1] PM: recover of devices complete after 3473.039 msecs
[ 31.309818][ 1] PM: Failed to load hibernation image, recovering.
[ 31.348188][ 1] PM: Basic memory bitmaps freed
[ 31.352686][ 1] OOM killer enabled.
[ 31.356232][ 1] Restarting tasks ... done.
[ 31.360609][ 1] PM: resume from hibernation failed (0)
[ 31.365800][ 1] PM: Hibernation image not present or could not be loaded.
The "do_wakeup" is determined based on whether the controller's
power/wakeup attribute is set. The current issue necessitates considering
the type of suspend that is occurring. If the suspend type is either
PM_EVENT_FREEZE or PM_EVENT_QUIESCE, then "do_wakeup" should be set to
false.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202410151722.rfjtknRz-lkp@intel.com/
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Duan Chenghao <duanchenghao@kylinos.cn>
Link: https://lore.kernel.org/r/20241024024038.26157-1-duanchenghao@kylinos.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Coverity from Synopsys complains "Illegal address computation (OVERRUN)"
on status_reg.
After below code executed,
port_index = wIndex & 0xff;
port_index -= (port_index > 0);
the static analysis tool see the value of port_index is now between 0 and
254 (inclusive).
However, ehci_def.h define port_status as below:
#define HCS_N_PORTS_MAX 15
u32 port_status[HCS_N_PORTS_MAX];
So the tool think illegal array pointer may be obtained.
status_reg = &ehci->regs->port_status[port_index];
This will follow "846cbf98cbef USB: EHCI: Improve port index sanitizing" to
improve port index sanitizing.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20241202083453.704533-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
STAR 9001346572 addresses a USB 2.0 endpoint blocking issue in host mode
for controller versions DWC_usb31 1.70a and 1.80a. This issue affects
devices on both high-speed and full-speed bus instances. When all
endpoint caches are filled and a single active endpoint receives
continuous NAK responses, data transfers to other endpoints may get
blocked.
To resolve this, for controller versions DWC_usb31 1.70a and 1.80a, the
GUCTL3 bit[16] (USB2.0 Internal Retry Disable) is set to 1. This bit
disables the USB2.0 internal retry feature and ensures proper eviction
handling in the host controller endpoind cache. The GUCTL3[16] register
function is available only from DWC_usb31 version 1.70a.
Signed-off-by: Faisal Hassan <quic_faisalh@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20241129173422.20063-1-quic_faisalh@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The two Kconfig "comment" calls render in /proc/config.gz as split
sections:
#
# NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may
#
#
# also be needed; see USB_STORAGE Help for more info
#
"make menuconfig" renders the comments as:
*** NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may ***
*** also be needed; see USB_STORAGE Help for more info ***
Kconfig doesn't support splitting a comment cleanly over two lines, so
just collapse it into a single oversize comment.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20241127232830.26923-2-ddiss@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sg (scatter-gather list pointer) member of the dwc3_request struct
is no longer used and should be removed. This patch eliminates the unused
member, cleaning up the struct.
This change improves code clarity and avoids maintaining unnecessary
members in the structure.
Reviewed-by: Ricardo B. Marliere <rbm@suse.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Closes: https://lore.kernel.org/all/20241118194006.77c7b126@canb.auug.org.au/
Signed-off-by: Luis Felipe Hernandez <luis.hernandez093@gmail.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20241120154604.51815-1-luis.hernandez093@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The header clearly states that it does not want to be included directly,
only via 'device.h'. 'platform_device.h' works equally well. Remove the
direct inclusion.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20241118072917.3853-15-wsa+renesas@sang-engineering.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit cdd30ebb1b ("module: Convert symbol namespace to string
literal") only converted MODULE_IMPORT_NS() and EXPORT_SYMBOL_NS(),
leaving DEFAULT_SYMBOL_NAMESPACE as a macro expansion.
This commit converts DEFAULT_SYMBOL_NAMESPACE in the same way to avoid
annoyance for the default namespace as well.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Add generic support for built-in boot DTB files
- Enable TAB cycling for dialog buttons in nconfig
- Fix issues in streamline_config.pl
- Refactor Kconfig
- Add support for Clang's AutoFDO (Automatic Feedback-Directed
Optimization)
- Add support for Clang's Propeller, a profile-guided optimization.
- Change the working directory to the external module directory for M=
builds
- Support building external modules in a separate output directory
- Enable objtool for *.mod.o and additional kernel objects
- Use lz4 instead of deprecated lz4c
- Work around a performance issue with "git describe"
- Refactor modpost
-----BEGIN PGP SIGNATURE-----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=GDKD
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
- Add generic support for built-in boot DTB files
- Enable TAB cycling for dialog buttons in nconfig
- Fix issues in streamline_config.pl
- Refactor Kconfig
- Add support for Clang's AutoFDO (Automatic Feedback-Directed
Optimization)
- Add support for Clang's Propeller, a profile-guided optimization.
- Change the working directory to the external module directory for M=
builds
- Support building external modules in a separate output directory
- Enable objtool for *.mod.o and additional kernel objects
- Use lz4 instead of deprecated lz4c
- Work around a performance issue with "git describe"
- Refactor modpost
* tag 'kbuild-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (85 commits)
kbuild: rename .tmp_vmlinux.kallsyms0.syms to .tmp_vmlinux0.syms
gitignore: Don't ignore 'tags' directory
kbuild: add dependency from vmlinux to resolve_btfids
modpost: replace tdb_hash() with hash_str()
kbuild: deb-pkg: add python3:native to build dependency
genksyms: reduce indentation in export_symbol()
modpost: improve error messages in device_id_check()
modpost: rename alias symbol for MODULE_DEVICE_TABLE()
modpost: rename variables in handle_moddevtable()
modpost: move strstarts() to modpost.h
modpost: convert do_usb_table() to a generic handler
modpost: convert do_of_table() to a generic handler
modpost: convert do_pnp_device_entry() to a generic handler
modpost: convert do_pnp_card_entries() to a generic handler
modpost: call module_alias_printf() from all do_*_entry() functions
modpost: pass (struct module *) to do_*_entry() functions
modpost: remove DEF_FIELD_ADDR_VAR() macro
modpost: deduplicate MODULE_ALIAS() for all drivers
modpost: introduce module_alias_printf() helper
modpost: remove unnecessary check in do_acpi_entry()
...
Here is a small set of driver core changes for 6.13-rc1.
Nothing major for this merge cycle, except for the 2 simple merge
conflicts are here just to make life interesting.
Included in here are:
- sysfs core changes and preparations for more sysfs api cleanups that
can come through all driver trees after -rc1 is out
- fw_devlink fixes based on many reports and debugging sessions
- list_for_each_reverse() removal, no one was using it!
- last-minute seq_printf() format string bug found and fixed in many
drivers all at once.
- minor bugfixes and changes full details in the shortlog
As mentioned above, there is 2 merge conflicts with your tree, one is
where the file is removed (easy enough to resolve), the second is a
build time error, that has been found in linux-next and the fix can be
seen here:
https://lore.kernel.org/r/20241107212645.41252436@canb.auug.org.au
Other than that, the changes here have been in linux-next with no other
reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZ0lEog8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ym+0ACgw6wN+LkLVIHWhxTq5DYHQ0QCxY8AoJrRIcKe
78h0+OU3OXhOy8JGz62W
=oI5S
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is a small set of driver core changes for 6.13-rc1.
Nothing major for this merge cycle, except for the two simple merge
conflicts are here just to make life interesting.
Included in here are:
- sysfs core changes and preparations for more sysfs api cleanups
that can come through all driver trees after -rc1 is out
- fw_devlink fixes based on many reports and debugging sessions
- list_for_each_reverse() removal, no one was using it!
- last-minute seq_printf() format string bug found and fixed in many
drivers all at once.
- minor bugfixes and changes full details in the shortlog"
* tag 'driver-core-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (35 commits)
Fix a potential abuse of seq_printf() format string in drivers
cpu: Remove spurious NULL in attribute_group definition
s390/con3215: Remove spurious NULL in attribute_group definition
perf: arm-ni: Remove spurious NULL in attribute_group definition
driver core: Constify bin_attribute definitions
sysfs: attribute_group: allow registration of const bin_attribute
firmware_loader: Fix possible resource leak in fw_log_firmware_info()
drivers: core: fw_devlink: Fix excess parameter description in docstring
driver core: class: Correct WARN() message in APIs class_(for_each|find)_device()
cacheinfo: Use of_property_present() for non-boolean properties
cdx: Fix cdx_mmap_resource() after constifying attr in ->mmap()
drivers: core: fw_devlink: Make the error message a bit more useful
phy: tegra: xusb: Set fwnode for xusb port devices
drm: display: Set fwnode for aux bus devices
driver core: fw_devlink: Stop trying to optimize cycle detection logic
driver core: Constify attribute arguments of binary attributes
sysfs: bin_attribute: add const read/write callback variants
sysfs: implement all BIN_ATTR_* macros in terms of __BIN_ATTR()
sysfs: treewide: constify attribute callback of bin_attribute::llseek()
sysfs: treewide: constify attribute callback of bin_attribute::mmap()
...
Here is the big set of USB and Thunderbolt changes for 6.13-rc1.
Overall, a pretty slow development cycle, the majority of the work going
into the debugfs interface for the thunderbolt (i.e. USB4) code, to help
with debugging the myrad ways that hardware vendors get their interfaces
messed up. Other than that, here's the highlights:
- thunderbolt changes and additions to debugfs interfaces
- lots of device tree updates for new and old hardware
- UVC configfs gadget updates and new apis for features
- xhci driver updates and fixes
- dwc3 driver updates and fixes
- typec driver updates and fixes
- lots of other small updates and fixes, full details in the shortlog
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZ0lBqA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynTXQCfSs0ldBqZoINU/22q8BUg7ybb+pcAoL5EbbEm
b2igfp6YIEWAtUkactmO
=gwwq
-----END PGP SIGNATURE-----
Merge tag 'usb-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt changes for 6.13-rc1.
Overall, a pretty slow development cycle, the majority of the work
going into the debugfs interface for the thunderbolt (i.e. USB4) code,
to help with debugging the myrad ways that hardware vendors get their
interfaces messed up. Other than that, here's the highlights:
- thunderbolt changes and additions to debugfs interfaces
- lots of device tree updates for new and old hardware
- UVC configfs gadget updates and new apis for features
- xhci driver updates and fixes
- dwc3 driver updates and fixes
- typec driver updates and fixes
- lots of other small updates and fixes, full details in the shortlog
All of these have been in linux-next for a while with no reported
problems"
* tag 'usb-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (148 commits)
usb: typec: tcpm: Add support for sink-bc12-completion-time-ms DT property
dt-bindings: usb: maxim,max33359: add usage of sink bc12 time property
dt-bindings: connector: Add time property for Sink BC12 detection completion
usb: dwc3: gadget: Remove dwc3_request->needs_extra_trb
usb: dwc3: gadget: Cleanup SG handling
usb: dwc3: gadget: Fix looping of queued SG entries
usb: dwc3: gadget: Fix checking for number of TRBs left
usb: dwc3: ep0: Don't clear ep0 DWC3_EP_TRANSFER_STARTED
Revert "usb: gadget: composite: fix OS descriptors w_value logic"
usb: ehci-spear: fix call balance of sehci clk handling routines
USB: make to_usb_device_driver() use container_of_const()
USB: make to_usb_driver() use container_of_const()
USB: properly lock dynamic id list when showing an id
USB: make single lock for all usb dynamic id lists
drivers/usb/storage: refactor min with min_t
drivers/usb/serial: refactor min with min_t
drivers/usb/musb: refactor min/max with min_t/max_t
drivers/usb/mon: refactor min with min_t
drivers/usb/misc: refactor min with min_t
drivers/usb/host: refactor min/max with min_t/max_t
...
tps65010, have undergone minor code improvements to enhance consistency and
fix race conditions.
- The syscon driver now utilizes the regmap max_register_is_0 capability
for consistent register map configuration across syscons of all sizes.
- New device support has been added for QCS8300, qcs615, SA8255p, and
samsung,s2dos05, expanding the range of compatible hardware.
- The cros_ec driver now supports loading cros_ec_ucsi on supported ECs
and avoids loading the charger with UCSI, streamlining functionality.
- The bd96801 driver now utilizes the more modern maple tree register
cache, improving performance.
- The da9052-spi driver has undergone a fix to change the read-mask to
write-mask, preventing potential issues.
- Unused declarations in max77693 have been removed, and support for
samsung,s2dos05 has been added, enhancing code clarity and device compatibility.
- Error handling in cs42l43 has been fixed to avoid unbalanced regulator
put and ensure proper synchronization during driver removal.
- The wcd934x driver now uses MODULE_DEVICE_TABLE() instead of
MODULE_ALIAS(), improving code consistency.
- Documentation for qcom,tcsr, syscon, and atmel-smc has been updated
and reorganized for better clarity and maintainability.
- The intel_soc_pmic_bxtwc driver has undergone significant improvements,
including the use of IRQ domains for various devices, fixing IRQ domain names
duplication, and code refactoring for better consistency and maintainability.
- The ipaq-micro driver has received a fix for a missing break statement in
the default case, enhancing code robustness.
- Support for the AXP323 PMIC has been added to the axp20x driver, along
with ensuring a clear relationship between IDs and model names, and allowing
multiple regulators, broadening hardware compatibility.
- The cs42l43 driver now disables IRQs during suspend for improved power
management.
- The adp5585 driver has reduced its dependencies by dropping the obsolete
dependency on COMPILE_TEST.
- Initial support for the MT6328 PMIC has been added to the mt6397 driver,
expanding the range of supported hardware.
- The rtc-bd70528 driver has been simplified by dropping the IC name from
IRQ, improving code readability.
- Documentation for qcom,spmi-pmic, ti,twl, and zii,rave-sp has been
updated to enhance clarity and incorporate new features.
- The rt5033 driver has received a fix for a missing regmap_del_irq_chip()
in the error handling path.
- New device support has been added for MSM8917, and the
intel_soc_pmic_crc driver now supports non-ACPI instantiated i2c_client.
- The 88pm886 driver has added support for the RTC cell, and the tqmx86
driver has improved its GPIO IRQ setup and added I2C IRQ support,
increasing functionality.
- The sprd,sc2731 DT schema has been updated and converted to YAML format
for better readability and maintainability.
-----BEGIN PGP SIGNATURE-----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=YP3r
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
- Several drivers, including atmel-flexcom/rk8xx-core, palmas, and
tps65010, have undergone minor code improvements to enhance
consistency and fix race conditions.
- The syscon driver now utilizes the regmap max_register_is_0
capability for consistent register map configuration across syscons
of all sizes.
- New device support has been added for QCS8300, qcs615, SA8255p, and
samsung,s2dos05, expanding the range of compatible hardware.
- The cros_ec driver now supports loading cros_ec_ucsi on supported ECs
and avoids loading the charger with UCSI, streamlining functionality.
- The bd96801 driver now utilizes the more modern maple tree register
cache, improving performance.
- The da9052-spi driver has undergone a fix to change the read-mask to
write-mask, preventing potential issues.
- Unused declarations in max77693 have been removed, and support for
samsung,s2dos05 has been added, enhancing code clarity and device
compatibility.
- Error handling in cs42l43 has been fixed to avoid unbalanced
regulator put and ensure proper synchronization during driver
removal.
- The wcd934x driver now uses MODULE_DEVICE_TABLE() instead of
MODULE_ALIAS(), improving code consistency.
- Documentation for qcom,tcsr, syscon, and atmel-smc has been updated
and reorganized for better clarity and maintainability.
- The intel_soc_pmic_bxtwc driver has undergone significant
improvements, including the use of IRQ domains for various devices,
fixing IRQ domain names duplication, and code refactoring for better
consistency and maintainability.
- The ipaq-micro driver has received a fix for a missing break
statement in the default case, enhancing code robustness.
- Support for the AXP323 PMIC has been added to the axp20x driver,
along with ensuring a clear relationship between IDs and model names,
and allowing multiple regulators, broadening hardware compatibility.
- The cs42l43 driver now disables IRQs during suspend for improved
power management.
- The adp5585 driver has reduced its dependencies by dropping the
obsolete dependency on COMPILE_TEST.
- Initial support for the MT6328 PMIC has been added to the mt6397
driver, expanding the range of supported hardware.
- The rtc-bd70528 driver has been simplified by dropping the IC name
from IRQ, improving code readability.
- Documentation for qcom,spmi-pmic, ti,twl, and zii,rave-sp has been
updated to enhance clarity and incorporate new features.
- The rt5033 driver has received a fix for a missing
regmap_del_irq_chip() in the error handling path.
- New device support has been added for MSM8917, and the
intel_soc_pmic_crc driver now supports non-ACPI instantiated
i2c_client.
- The 88pm886 driver has added support for the RTC cell, and the tqmx86
driver has improved its GPIO IRQ setup and added I2C IRQ support,
increasing functionality.
- The sprd,sc2731 DT schema has been updated and converted to YAML
format for better readability and maintainability.
* tag 'mfd-next-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (62 commits)
dt-bindings: mfd: bd71828: Use charger resistor in mOhm instead of MOhm
dt-bindings: mfd: sprd,sc2731: Convert to YAML
mfd: tqmx86: Add I2C IRQ support
mfd: tqmx86: Make IRQ setup errors non-fatal
mfd: tqmx86: Refactor GPIO IRQ setup
mfd: tqmx86: Improve gpio_irq module parameter description
mfd: tqmx86: Add board definitions for TQMx120UC, TQMx130UC and TQMxE41S
mfd: 88pm886: Add the RTC cell
dt-bindings: mfd: Add Realtek RTL9300 switch peripherals
mfd: intel_soc_pmic_crc: Add support for non ACPI instantiated i2c_client
mfd: intel_soc_pmic_*: Consistently use filename as driver name
dt-bindings: mfd: qcom,tcsr: Add compatible for MSM8917
mfd: rt5033: Fix missing regmap_del_irq_chip()
mfd: cgbc-core: Fix error handling paths in cgbc_init_device()
dt-bindings: mfd: aspeed: Support for AST2700
mfd: Switch back to struct platform_driver::remove()
dt-bindings: mfd: qcom,spmi-pmic: Document PMICs added in SM8750
mfd: rtc: bd7xxxx Drop IC name from IRQ
mfd: mt6397: Add initial support for MT6328
mfd: adp5585: Drop obsolete dependency on COMPILE_TEST
...
GPIOLIB core:
- use the new mem_is_zero() instead of memchr_inv(s, 0, n)
- don't store debounce period twice needlessly
- clean-up debugfs handling
- remove leftover comments referring to no longer used spinlocks
- unduplicate some operations like SRCU locks and initializing GPIO descriptors
- constify the sysfs class struct
- use lock guards in GPIO sysfs code
- update GPIO uAPI internal flags all at once atomically for consistency with
other places
- modify the behavior of the sysfs interface by no longer exporting lines that
are named inside the driver code or board files with the sysfs links bearing
the line names as this has for many years been largely unused due to the
prevalence of DT, ACPI and firmware nodes over board files and made the API
inconsistent
- for GPIO interrupt providers: free irqs that are still requested by users
when removing the chip
GPIO uAPI:
- notify user-space about changes to GPIO lines' state (requested, released,
reconfigured) triggered from the kernel as well (until now we'd only do
this for changes triggered from user-space)
- to that end: modify the internal workings of the notification mechanism by
switching to an atomic notifier which allows us to send events from atomic
context
- also to that end store the debounce period in the GPIO descriptor struct
and not in the character device context struct
- while at it, also cover the corner-case of users introducing changes over
sysfs while others watch them via the character device
- don't report GPIO lines requested as interrupts as "used" to user-space as it
can still request them as GPIOs
New drivers:
- add a driver for the GPIO functionality of the MFD Congatec Board Controller
- add a driver for the PolarFire GPIO controller
- add a driver supporting the GPIOs on FTDI FT2232H
Driver improvements:
- use generic device property accessors instead of OF-specific ones across
many GPIO drivers (mpc8xxx, vf610, eic-sprd, davinci, ts4900, xilinx, mvebu)
- use devres helpers to simplify error paths and either shrink or entirely
remove the driver's remove() callback (grgpio, amdpt, menz127, max730x,
ftgpio010, 74x164, ljca)
- use helper variables to store the address of pdev->dev and avoid some
line-breaks
- use device_for_each_child_node_scoped() to avoid having to put the fwnode
on breaks or errors (gpio-sim, gpio-dwapb, gpiolib-acpi)
- use a scoped bitmap to simplify the code and drop goto labels in
gpio-aggregator
- drop unneeded Kconfig dependencies on OF_GPIO (grgpio, mveby, xilinx)
- add support for new models to gpio-aspeed, gpio-rockchip and gpio-dwapb
- clean-up ACPI handling and some other bits in gpio-xgene-sb
- replace deprecated PCI functions in pcie-idio-24 and pci-idio-16
- allow to build davinci and mvebu drivers with COMPILE_TEST=y
- remove dead code in gpio-mb86s7x
- switch back to using platform_driver::remove() (after the conversion to
remove_new()) across the GPIO drivers
- remove remaining uses of GPIOF_ACTIVE_LOW across the tree and drop this
deprecated symbol
- convert the gpio-altera driver to no longer pull in the deprecated
legacy-of-mm-gpiochip.h header
- use of_property_present() instead of of_property_read_bool() in gpiolib-of
and gpio-rockchip
- allow to build the tegra186 driver on Tegra234 platforms in Kconfig
Late fixes:
- add a missing return value check after devm_kasprintf() to gpio-grgpio
DT bindings:
- document the ngpios property of gpio-mmio
- add support for a new aspeed model
- fix the example for st,nomadik-gpio
Other:
- kernel doc and comments tweaks
- fix typos in TODO
- reorder headers alphabetically in some drivers
- fix incorrect format specifiers in gpio tools
-----BEGIN PGP SIGNATURE-----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=ON7q
-----END PGP SIGNATURE-----
Merge tag 'gpio-updates-for-v6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio updates from Bartosz Golaszewski:
"Three new drivers, support for some new models in existing ones and
lots of various tweaks and improvements across the board (switching to
using recommended APIs, code shrink and simplification, etc.).
Also a new feature in the character device uAPI where we now notify
the user-space about changes triggered by in-kernel users as well, not
only when they were done by other user-space agents.
Summary:
GPIOLIB core:
- use the new mem_is_zero() instead of memchr_inv(s, 0, n)
- don't store debounce period twice needlessly
- clean-up debugfs handling
- remove leftover comments referring to no longer used spinlocks
- unduplicate some operations like SRCU locks and initializing GPIO
descriptors
- constify the sysfs class struct
- use lock guards in GPIO sysfs code
- update GPIO uAPI internal flags all at once atomically for
consistency with other places
- modify the behavior of the sysfs interface by no longer exporting
lines that are named inside the driver code or board files with the
sysfs links bearing the line names as this has for many years been
largely unused due to the prevalence of DT, ACPI and firmware nodes
over board files and made the API inconsistent
- for GPIO interrupt providers: free irqs that are still requested by
users when removing the chip
GPIO uAPI:
- notify user-space about changes to GPIO lines' state (requested,
released, reconfigured) triggered from the kernel as well (until
now we'd only do this for changes triggered from user-space)
- to that end: modify the internal workings of the notification
mechanism by switching to an atomic notifier which allows us to
send events from atomic context
- also to that end store the debounce period in the GPIO descriptor
struct and not in the character device context struct
- while at it, also cover the corner-case of users introducing
changes over sysfs while others watch them via the character device
- don't report GPIO lines requested as interrupts as "used" to
user-space as it can still request them as GPIOs
New drivers:
- GPIO part of the MFD Congatec Board Controller
- PolarFire GPIO controller
- GPIOs on FTDI FT2232H
Driver improvements:
- use generic device property accessors instead of OF-specific ones
across many GPIO drivers (mpc8xxx, vf610, eic-sprd, davinci,
ts4900, xilinx, mvebu)
- use devres helpers to simplify error paths and either shrink or
entirely remove the driver's remove() callback (grgpio, amdpt,
menz127, max730x, ftgpio010, 74x164, ljca)
- use helper variables to store the address of pdev->dev and avoid
some line-breaks
- use device_for_each_child_node_scoped() to avoid having to put the
fwnode on breaks or errors (gpio-sim, gpio-dwapb, gpiolib-acpi)
- use a scoped bitmap to simplify the code and drop goto labels in
gpio-aggregator
- drop unneeded Kconfig dependencies on OF_GPIO (grgpio, mveby,
xilinx)
- add support for new models to gpio-aspeed, gpio-rockchip and
gpio-dwapb
- clean-up ACPI handling and some other bits in gpio-xgene-sb
- replace deprecated PCI functions in pcie-idio-24 and pci-idio-16
- allow to build davinci and mvebu drivers with COMPILE_TEST=y
- remove dead code in gpio-mb86s7x
- switch back to using platform_driver::remove() (after the
conversion to remove_new()) across the GPIO drivers
- remove remaining uses of GPIOF_ACTIVE_LOW across the tree and drop
this deprecated symbol
- convert the gpio-altera driver to no longer pull in the deprecated
legacy-of-mm-gpiochip.h header
- use of_property_present() instead of of_property_read_bool() in
gpiolib-of and gpio-rockchip
- allow to build the tegra186 driver on Tegra234 platforms in Kconfig
Late fixes:
- add a missing return value check after devm_kasprintf() to
gpio-grgpio
DT bindings:
- document the ngpios property of gpio-mmio
- add support for a new aspeed model
- fix the example for st,nomadik-gpio
Other:
- kernel doc and comments tweaks
- fix typos in TODO
- reorder headers alphabetically in some drivers
- fix incorrect format specifiers in gpio tools"
* tag 'gpio-updates-for-v6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (98 commits)
gpio: tegra186: Allow to enable driver on Tegra234
gpio: grgpio: Add NULL check in grgpio_probe
tools: gpio: Fix several incorrect format specifiers
gpio: mpfs: add CoreGPIO support
gpio: rockchip: support new version GPIO
gpio: rockchip: change the GPIO version judgment logic
gpio: rockchip: explan the format of the GPIO version ID
gpiolib: cdev: use !mem_is_zero() instead of memchr_inv(s, 0, n)
MAINTAINERS: add gpio driver to PolarFire entry
gpio: Get rid of GPIOF_ACTIVE_LOW
USB: gadget: pxa27x_udc: Avoid using GPIOF_ACTIVE_LOW
pcmcia: soc_common: Avoid using GPIOF_ACTIVE_LOW
leds: gpio: Avoid using GPIOF_ACTIVE_LOW
Input: gpio_keys_polled - avoid using GPIOF_ACTIVE_LOW
Input: gpio_keys - avoid using GPIOF_ACTIVE_LOW
gpio: Use of_property_present() for non-boolean properties
gpio: mpfs: add polarfire soc gpio support
gpio: altera: Drop legacy-of-mm-gpiochip.h header
gpio: pcie-idio-24: Replace deprecated PCI functions
gpio: pci-idio-16: Replace deprecated PCI functions
...
Add support for parsing DT time property "sink-bc12-completion-time-ms".
This timer is used to relax the PD state machine during Sink attach to
allow completion of Battery Charging (BC1.2) charger type detection in
TCPC before PD negotiations. BC1.2 detection is a hardware mechanism to
detect charger port type that is run by some controllers (such as
"maxim,max33359") in parallel to Type-C connection state machines.
This is to ensure that BC1.2 completes before PD is enabled as running
BC1.2 in parallel with PD negotiation results in delays violating timer
constraints in PD spec.
This is an optional timer and will not add any delay unless explicitly
set.
Signed-off-by: Amit Sunil Dhamne <amitsd@google.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20241103034402.2460252-4-amitsd@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current logic in dwc3 driver is tracking req->num_queued_sgs and
req->sg. But they can be checked base on the num_pending_sgs and
num_trbs. They are redundant and can complicate the SG logic. Let's
remove them.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/96c7bf8f6b3e91e607d5b78ea51cb1d00c614eaf.1731545781.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dwc3_request->num_queued_sgs is decremented on completion. If a
partially completed request is handled, then the
dwc3_request->num_queued_sgs no longer reflects the total number of
num_queued_sgs (it would be cleared).
Correctly check the number of request SG entries remained to be prepare
and queued. Failure to do this may cause null pointer dereference when
accessing non-existent SG entry.
Cc: stable@vger.kernel.org
Fixes: c96e6725db ("usb: dwc3: gadget: Correct the logic for queuing sgs")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/d07a7c4aa0fcf746cdca0515150dbe5c52000af7.1731545781.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The check whether the TRB ring is full or empty in dwc3_calc_trbs_left()
is insufficient. It assumes there are active TRBs if there's any request
in the started_list. However, that's not the case for requests with a
large SG list.
That is, if we have a single usb request that requires more TRBs than
the total TRBs in the TRB ring, the queued TRBs will be available when
all the TRBs in the ring are completed. But the request is only
partially completed and remains in the started_list. With the current
logic, the TRB ring is empty, but dwc3_calc_trbs_left() returns 0.
Fix this by additionally checking for the request->num_trbs for active
TRB count.
Cc: stable@vger.kernel.org
Fixes: 51f1954ad8 ("usb: dwc3: gadget: Fix dwc3_calc_trbs_left()")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/708dc62b56b77da1f704cc2ae9b6ddb1f2dbef1f.1731545781.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver cannot issue the End Transfer command to the SETUP transfer.
Don't clear DWC3_EP_TRANSFER_STARTED flag to make sure that the driver
won't send Start Transfer command again, which can cause no-resource
error. For example this can occur if the host issues a reset to the
device.
Cc: stable@vger.kernel.org
Fixes: 76cb323f80 ("usb: dwc3: ep0: clear all EP0 flags")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/d3d618185fd614bb7426352a9fc1199641d3b5f5.1731545781.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit ec6ce7075e.
Fix installation of WinUSB driver using OS descriptors. Without the
fix the drivers are not installed correctly and the property
'DeviceInterfaceGUID' is missing on host side.
The original change was based on the assumption that the interface
number is in the high byte of wValue but it is in the low byte,
instead. Unfortunately, the fix is based on MS documentation which is
also wrong.
The actual USB request for OS descriptors (using USB analyzer) looks
like:
Offset 0 1 2 3 4 5 6 7
0x000 C1 A1 02 00 05 00 0A 00
C1: bmRequestType (device to host, vendor, interface)
A1: nas magic number
0002: wValue (2: nas interface)
0005: wIndex (5: get extended property i.e. nas interface GUID)
008E: wLength (142)
The fix was tested on Windows 10 and Windows 11.
Cc: stable@vger.kernel.org
Fixes: ec6ce7075e ("usb: gadget: composite: fix OS descriptors w_value logic")
Signed-off-by: Michal Vrastil <michal.vrastil@hidglobal.com>
Signed-off-by: Elson Roy Serrao <quic_eserrao@quicinc.com>
Acked-by: Peter korsgaard <peter@korsgaard.com>
Link: https://lore.kernel.org/r/20241113235433.20244-1-quic_eserrao@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the clock sehci->clk was not enabled in spear_ehci_hcd_drv_probe,
it should not be disabled in any path.
Conversely, if it was enabled in spear_ehci_hcd_drv_probe, it must be disabled
in all error paths to ensure proper cleanup.
Found by Linux Verification Center (linuxtesting.org) with Klever.
Fixes: 7675d6ba43 ("USB: EHCI: make ehci-spear a separate driver")
Cc: stable@vger.kernel.org
Signed-off-by: Vitalii Mordan <mordan@ispras.ru>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20241114230310.432213-1-mordan@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are the USB-serial updates for 6.13-rc1, including:
- improved support for quirky pl2303 hxd devices
- make sure ftdi_sio TIOCGSERIAL returns consistent data
Everything has been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCZzdTXQAKCRALxc3C7H1l
COSGAP0U6gSnhn9V6cSzz9WVJwfAAifKkBB6ZvPORmOX4f5nMwEAtEEQJQtdCXD6
d/9/9hEF1Xot5nhKfOTtFMbwWM+rtgI=
=gbhm
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-6.13-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for 6.13-rc1
Here are the USB-serial updates for 6.13-rc1, including:
- improved support for quirky pl2303 hxd devices
- make sure ftdi_sio TIOCGSERIAL returns consistent data
Everything has been in linux-next with no reported issues.
* tag 'usb-serial-6.13-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: ftdi_sio: Fix atomicity violation in get_serial_info()
USB: serial: pl2303: account for deficits of clones
Turns out that we have some const pointers being passed to
to_usb_device_driver() but were not catching this. Change the macro to
properly propagate the const-ness of the pointer so that we will notice
when we try to write to memory that we shouldn't be writing to.
This requires fixing up the usb_driver_applicable() function as well,
because it can handle a const * to struct usb_driver.
Cc: Johan Hovold <johan@kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Grant Grundler <grundler@chromium.org>
Cc: Yajun Deng <yajun.deng@linux.dev>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: linux-usb@vger.kernel.org
Link: https://lore.kernel.org/r/2024111342-lagoon-reapprove-5e49@gregkh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Turns out that we have some const pointers being passed to
to_usb_driver() but were not catching this. Change the macro to
properly propagate the const-ness of the pointer so that we will notice
when we try to write to memory that we shouldn't be writing to.
This requires fixing up the usb_match_dynamic_id() function as well,
because it can handle a const * to struct usb_driver.
Cc: Johan Hovold <johan@kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Grant Grundler <grundler@chromium.org>
Cc: Yajun Deng <yajun.deng@linux.dev>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: linux-usb@vger.kernel.org
Link: https://lore.kernel.org/r/2024111339-shaky-goldsmith-b233@gregkh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When walking the list of dynamic ids for a driver, no lock was being
held, which meant that an id could be removed or added while the list
was being iterated. Fix this up by properly grabing the lock while we
walk the list.
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Cc: linux-usb@vger.kernel.org
Link: https://lore.kernel.org/r/2024111324-tubby-facecloth-d4a0@gregkh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are a number of places where we accidentally pass in a constant
structure to later cast it off to a dynamic one, and then attempt to
grab a lock on it, which is not a good idea. To help resolve this, move
the dynamic id lock out of the dynamic id structure for the driver and
into one single lock for all USB dynamic ids. As this lock should never
have any real contention (it's only every accessed when a device is
added or removed, which is always serialized) there should not be any
difference except for some memory savings.
Note, this just converts the existing use of the dynamic id lock to the
new static lock, there is one place that is accessing the dynamic id
list without grabbing the lock, that will be fixed up in a follow-on
change.
Cc: Johan Hovold <johan@kernel.org>
Cc: Herve Codina <herve.codina@bootlin.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Grant Grundler <grundler@chromium.org>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Yajun Deng <yajun.deng@linux.dev>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: linux-usb@vger.kernel.org
Link: https://lore.kernel.org/r/2024111322-kindly-finalist-d247@gregkh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ensure type safety by using min_t() instead of min().
Also add the explicit `unsigned int` as scripts/checkpatch.pl warns about:
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
Signed-off-by: Sabyrzhan Tasbolatov <snovitoll@gmail.com>
Link: https://lore.kernel.org/r/20241112155817.3512577-5-snovitoll@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are a few places in the kernel where PCI IDs for different Cadence
USB controllers are being used. Besides different naming, they duplicate
each other. Make this all in order by providing common definitions via
PCI IDs database and use in all users. While doing that, rename
definitions as Roger suggested.
Suggested-by: Roger Quadros <rogerq@kernel.org>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20241112160125.2340972-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently if the maximum-speed is set to Super Speed for a 3.1 Gen2
capable controller, the FORCE_GEN1 bit of LLUCTL register is set only
for one SuperSpeed port (or the first port) present. Modify the logic
to set the FORCE_GEN1 bit for all ports if speed is being limited to
Gen-1.
Suggested-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20241112182018.199392-1-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The existing implementation of the TxFIFO resizing logic only supports
scenarios where more than one port RAM is used. However, there is a need
to resize the TxFIFO in USB2.0-only mode where only a single port RAM is
available. This commit introduces the necessary changes to support
TxFIFO resizing in such scenarios by adding a missing check for single
port RAM.
This fix addresses certain platform configurations where the existing
TxFIFO resizing logic does not work properly due to the absence of
support for single port RAM. By adding this missing check, we ensure
that the TxFIFO resizing logic works correctly in all scenarios,
including those with a single port RAM.
Fixes: 9f607a309f ("usb: dwc3: Resize TX FIFOs to meet EP bursting requirements")
Cc: stable@vger.kernel.org # 6.12.x: fad16c82: usb: dwc3: gadget: Refine the logic for resizing Tx FIFOs
Signed-off-by: Selvarasu Ganesan <selvarasu.g@samsung.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20241112044807.623-1-selvarasu.g@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "command" variable can be controlled by the user via debugfs. The
worry is that if con_index is zero then "&uc->ucsi->connector[con_index
- 1]" would be an array underflow.
Fixes: 170a6726d0 ("usb: typec: ucsi: add support for separate DP altmode devices")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/c69ef0b3-61b0-4dde-98dd-97b97f81d912@stanley.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some Lenovo platforms, the patch works around problems with ov2740
sensor initialization, which manifest themself like below:
[ 4.540476] ov2740 i2c-INT3474:01: error -EIO: failed to find sensor
[ 4.542066] ov2740 i2c-INT3474:01: probe with driver ov2740 failed with error -5
or
[ 7.742633] ov2740 i2c-INT3474:01: chip id mismatch: 2740 != 0
[ 7.742638] ov2740 i2c-INT3474:01: error -ENXIO: failed to find sensor
and also by random failures of video stream start.
Issue can be reproduced by this script:
n=0
k=0
while [ $n -lt 50 ] ; do
sudo modprobe -r ov2740
sleep `expr $RANDOM % 5`
sudo modprobe ov2740
if media-ctl -p | grep -q ov2740 ; then
let k++
fi
let n++
done
echo Success rate $k/$n
Without the patch, success rate is approximately 15 or 50 tries.
With the patch it does not fail.
This problem is some hardware or firmware malfunction, that can not be
easy debug and fix. While setting small autosuspend delay is not perfect
workaround as user can configure it to any value, it will prevent
the failures by default.
Additionally setting small autosuspend delay should have positive effect
on power consumption as for most ljca workloads device is used for just
a few milliseconds flowed by long periods of at least 100ms of inactivity
(usually more).
Fixes: acd6199f19 ("usb: Add support for Intel LJCA device")
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com> # ThinkPad X1 Yoga Gen 8, ov2740
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://lore.kernel.org/r/20241112075514.680712-2-stanislaw.gruszka@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not mark interface as ready to suspend when we are still waiting
for response messages from the device.
Fixes: acd6199f19 ("usb: Add support for Intel LJCA device")
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com> # ThinkPad X1 Yoga Gen 8, ov2740
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://lore.kernel.org/r/20241112075514.680712-1-stanislaw.gruszka@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dtbinding have imx7ulp and imx8ulp compatible with imx7d before. And
then the dtb follow the dtbinding. However, the driver doesn't add imx8ulp
compatible now. To make imx8ulp work well, this will add support for it.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20241111090916.1534047-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The GET_CAPABILITY size is wrong. The definitions for the
command sizes are for bitfieds and therefore in bits, not
bytes.
This fixes an issue that prevents the interface from being
registered with UCSI versions older than 2.0 because the
command size exceeds the MESSAGE_IN field size.
Fixes: 226ff2e681 ("usb: typec: ucsi: Convert connector specific commands to bitmaps")
Reported-by: Abel Vesa <abel.vesa@linaro.org>
Closes: https://lore.kernel.org/linux-usb/Zy864W7sysWZbCTd@linaro.org/
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Tested-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20241111100220.1743872-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a possibility that a request's callback could be invoked from
usb_ep_queue() (call trace below, supplemented with missing calls):
req->complete from usb_gadget_giveback_request
(drivers/usb/gadget/udc/core.c:999)
usb_gadget_giveback_request from musb_g_giveback
(drivers/usb/musb/musb_gadget.c:147)
musb_g_giveback from rxstate
(drivers/usb/musb/musb_gadget.c:784)
rxstate from musb_ep_restart
(drivers/usb/musb/musb_gadget.c:1169)
musb_ep_restart from musb_ep_restart_resume_work
(drivers/usb/musb/musb_gadget.c:1176)
musb_ep_restart_resume_work from musb_queue_resume_work
(drivers/usb/musb/musb_core.c:2279)
musb_queue_resume_work from musb_gadget_queue
(drivers/usb/musb/musb_gadget.c:1241)
musb_gadget_queue from usb_ep_queue
(drivers/usb/gadget/udc/core.c:300)
According to the docstring of usb_ep_queue(), this should not happen:
"Note that @req's ->complete() callback must never be called from within
usb_ep_queue() as that can create deadlock situations."
In fact, a hardware lockup might occur in the following sequence:
1. The gadget is initialized using musb_gadget_enable().
2. Meanwhile, a packet arrives, and the RXPKTRDY flag is set, raising an
interrupt.
3. If IRQs are enabled, the interrupt is handled, but musb_g_rx() finds an
empty queue (next_request() returns NULL). The interrupt flag has
already been cleared by the glue layer handler, but the RXPKTRDY flag
remains set.
4. The first request is enqueued using usb_ep_queue(), leading to the call
of req->complete(), as shown in the call trace above.
5. If the callback enables IRQs and another packet is waiting, step (3)
repeats. The request queue is empty because usb_g_giveback() removes the
request before invoking the callback.
6. The endpoint remains locked up, as the interrupt triggered by hardware
setting the RXPKTRDY flag has been handled, but the flag itself remains
set.
For this scenario to occur, it is only necessary for IRQs to be enabled at
some point during the complete callback. This happens with the USB Ethernet
gadget, whose rx_complete() callback calls netif_rx(). If called in the
task context, netif_rx() disables the bottom halves (BHs). When the BHs are
re-enabled, IRQs are also enabled to allow soft IRQs to be processed. The
gadget itself is initialized at module load (or at boot if built-in), but
the first request is enqueued when the network interface is brought up,
triggering rx_complete() in the task context via ioctl(). If a packet
arrives while the interface is down, it can prevent the interface from
receiving any further packets from the USB host.
The situation is quite complicated with many parties involved. This
particular issue can be resolved in several possible ways:
1. Ensure that callbacks never enable IRQs. This would be difficult to
enforce, as discovering how netif_rx() interacts with interrupts was
already quite challenging and u_ether is not the only function driver.
Similar "bugs" could be hidden in other drivers as well.
2. Disable MUSB interrupts in musb_g_giveback() before calling the callback
and re-enable them afterwars (by calling musb_{dis,en}able_interrupts(),
for example). This would ensure that MUSB interrupts are not handled
during the callback, even if IRQs are enabled. In fact, it would allow
IRQs to be enabled when releasing the lock. However, this feels like an
inelegant hack.
3. Modify the interrupt handler to clear the RXPKTRDY flag if the request
queue is empty. While this approach also feels like a hack, it wastes
CPU time by attempting to handle incoming packets when the software is
not ready to process them.
4. Flush the Rx FIFO instead of calling rxstate() in musb_ep_restart().
This ensures that the hardware can receive packets when there is at
least one request in the queue. Once IRQs are enabled, the interrupt
handler will be able to correctly process the next incoming packet
(eventually calling rxstate()). This approach may cause one or two
packets to be dropped (two if double buffering is enabled), but this
seems to be a minor issue, as packet loss can occur when the software is
not yet ready to process them. Additionally, this solution makes the
gadget driver compliant with the rule mentioned in the docstring of
usb_ep_queue().
There may be additional solutions, but from these four, the last one has
been chosen as it seems to be the most appropriate, as it addresses the
"bad" behavior of the driver.
Fixes: baebdf48c3 ("net: dev: Makes sure netif_rx() can be invoked in any context.")
Cc: stable@vger.kernel.org
Signed-off-by: Hubert Wiśniewski <hubert.wisniewski.25632@gmail.com>
Link: https://lore.kernel.org/r/4ee1ead4525f78fb5909a8cbf99513ad0082ad21.camel@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of checking if any of the USB-C ports have orientation GPIO and
thus is orientation-aware, check for the GPIO for the port being
registered. There are no boards that are affected by this change at this
moment, so the patch is not marked as a fix, but it might affect other
boards in future.
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20241109-ucsi-glue-fixes-v2-2-8b21ff4f9fbe@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UCSI connector's indices start from 1 up to 3, PMIC_GLINK_MAX_PORTS.
Correct the condition in the pmic_glink_ucsi_connector_status()
callback, fixing Type-C orientation reporting for the third USB-C
connector.
Fixes: 76716fd5bf ("usb: typec: ucsi: glink: move GPIO reading into connector_status callback")
Cc: stable@vger.kernel.org
Reported-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20241109-ucsi-glue-fixes-v2-1-8b21ff4f9fbe@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After an initial range change on the insigned int alt being > 1
the only possible values for alt are 0 or 1. Therefore the else
statement for values other than 0 or 1 is redundant and can be
removed. Replace the else if (all == 1) check with just an else.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/5f54ffd0-b5fe-4203-a626-c166becad362@gmail.com
Link: https://lore.kernel.org/r/20241107133348.22762-1-colin.i.king@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's a fix for a long-standing use-after-free in an io_edgeport debug
printk and some new modem device ids.
All have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCZy29qQAKCRALxc3C7H1l
CKN8AP9hD+7glW6sf0JDJ3zcN9vPIn1NLqALMil7Ga8hrmy2wQD/ff/mBrJqugF+
pQ1nFCQzLR2LtQEWRm/5ebb9yeaE1gE=
=3wbn
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-6.12-rc7' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 6.12-rc7
Here's a fix for a long-standing use-after-free in an io_edgeport debug
printk and some new modem device ids.
All have been in linux-next with no reported issues.
* tag 'usb-serial-6.12-rc7' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: qcserial: add support for Sierra Wireless EM86xx
USB: serial: io_edgeport: fix use after free in debug printk
USB: serial: option: add Quectel RG650V
USB: serial: option: add Fibocom FG132 0x0112 composition
Our static checker found a bug where set_serial_info() uses a mutex, but
get_serial_info() does not. Fortunately, the impact of this is relatively
minor. It doesn't cause a crash or any other serious issues. However, if a
race condition occurs between set_serial_info() and get_serial_info(),
there is a chance that the data returned by get_serial_info() will be
inconsistent.
Fixes: 3ae36bed3a ("fdti_sio: switch to ->[sg]et_serial()")
Signed-off-by: Qiu-ji Chen <chenqiuji666@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
That allows the fields in those command data structures to
be easily validated. If an unsupported field is accessed, a
warning is generated.
This will not force UCSI version checks to be made in every
place where these data structures are accessed, but it will
make it easier to pinpoint issues that are caused by the
unconditional accesses to those fields, and perhaps more
importantly, allow those issues to be noticed immediately.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20241106150605.1017744-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are apparently incomplete clones of the HXD type chip in use.
Those return -EPIPE on GET_LINE_REQUEST and BREAK_REQUEST. Avoid
flooding the kernel log with those errors. Detect them during startup
and then use the line_settings cache instead of GET_LINE_REQUEST. Signal
missing break support via -ENOTTY.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
[ johan: fix macro prefix, drop oom error message ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Stop Endpoint command on an already stopped endpoint fails and may be
misinterpreted as a known hardware bug by the completion handler. This
results in an unnecessary delay with repeated retries of the command.
Avoid queuing this command when endpoint state flags indicate that it's
stopped or halted and the command will fail. If commands are pending on
the endpoint, their completion handlers will process cancelled TDs so
it's done. In case of waiting for external operations like clearing TT
buffer, the endpoint is stopped and cancelled TDs can be processed now.
This eliminates practically all unnecessary retries because an endpoint
with pending URBs is maintained in Running state by the driver, unless
aforementioned commands or other operations are pending on it. This is
guaranteed by xhci_ring_ep_doorbell() and by the fact that it is called
every time any of those operations completes.
The only known exceptions are hardware bugs (the endpoint never starts
at all) and Stream Protocol errors not associated with any TRB, which
cause an endpoint reset not followed by restart. Sounds like a bug.
Generally, these retries are only expected to happen when the endpoint
fails to start for unknown/no reason, which is a worse problem itself,
and fixing the bug eliminates the retries too.
All cases were tested and found to work as expected. SET_DEQ_PENDING
was produced by patching uvcvideo to unlink URBs in 100us intervals,
which then runs into this case very often. EP_HALTED was produced by
restarting 'cat /dev/ttyUSB0' on a serial dongle with broken cable.
EP_CLEARING_TT by the same, with the dongle on an external hub.
Fixes: fd9d55d190 ("xhci: retry Stop Endpoint on buggy NEC controllers")
CC: stable@vger.kernel.org
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-34-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_invalidate_cancelled_tds() may not work correctly if the hardware
is modifying endpoint or stream contexts at the same time by executing
a Set TR Dequeue command. And even if it worked, it would be unable to
queue Set TR Dequeue for the next stream, failing to clear xHC cache.
On stream endpoints, a chain of Set TR Dequeue commands may take some
time to execute and we may want to cancel more TDs during this time.
Currently this leads to Stop Endpoint completion handler calling this
function without testing for SET_DEQ_PENDING, which will trigger the
aforementioned problems when it happens.
On all endpoints, a halt condition causes Reset Endpoint to be queued
and an error status given to the class driver, which may unlink more
URBs in response. Stop Endpoint is queued and its handler may execute
concurrently with Set TR Dequeue queued by Reset Endpoint handler.
(Reset Endpoint handler calls this function too, but there seems to
be no possibility of it running concurrently with Set TR Dequeue).
Fix xhci_invalidate_cancelled_tds() to work correctly under a pending
Set TR Dequeue. Bail out of the function when SET_DEQ_PENDING is set,
then make the completion handler call the function again and also call
xhci_giveback_invalidated_tds(), which needs to be called next.
This seems to fix another potential bug, where the handler would call
xhci_invalidate_cancelled_tds(), which may clear some deferred TDs if
a sanity check fails, and the TDs wouldn't be given back promptly.
Said sanity check seems to be wrong and prone to false positives when
the endpoint halts, but fixing it is beyond the scope of this change,
besides ensuring that cleared TDs are given back properly.
Fixes: 5ceac4402f ("xhci: Handle TD clearing for multiple streams case")
CC: stable@vger.kernel.org
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-33-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some host controllers fail to atomically transition an endpoint to the
Running state on a doorbell ring and enter a hidden "Restarting" state,
which looks very much like Stopped, with the important difference that
it will spontaneously transition to Running anytime soon.
A Stop Endpoint command queued in the Restarting state typically fails
with Context State Error and the completion handler sees the Endpoint
Context State as either still Stopped or already Running. Even a case
of Halted was observed, when an error occurred right after the restart.
The Halted state is already recovered from by resetting the endpoint.
The Running state is handled by retrying Stop Endpoint.
The Stopped state was recognized as a problem on NEC controllers and
worked around also by retrying, because the endpoint soon restarts and
then stops for good. But there is a risk: the command may fail if the
endpoint is "stopped for good" already, and retries will fail forever.
The possibility of this was not realized at the time, but a number of
cases were discovered later and reproduced. Some proved difficult to
deal with, and it is outright impossible to predict if an endpoint may
fail to ever start at all due to a hardware bug. One such bug (albeit
on ASM3142, not on NEC) was found to be reliably triggered simply by
toggling an AX88179 NIC up/down in a tight loop for a few seconds.
An endless retries storm is quite nasty. Besides putting needless load
on the xHC and CPU, it causes URBs never to be given back, paralyzing
the device and connection/disconnection logic for the whole bus if the
device is unplugged. User processes waiting for URBs become unkillable,
drivers and kworker threads lock up and xhci_hcd cannot be reloaded.
For peace of mind, impose a timeout on Stop Endpoint retries in this
case. If they don't succeed in 100ms, consider the endpoint stopped
permanently for some reason and just give back the unlinked URBs. This
failure case is rare already and work is under way to make it rarer.
Start this work today by also handling one simple case of race with
Reset Endpoint, because it costs just two lines to implement.
Fixes: fd9d55d190 ("xhci: retry Stop Endpoint on buggy NEC controllers")
CC: stable@vger.kernel.org
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-32-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code which it is referencing does not exist in the same function,
or the file for that matter. Since it was added [1], the Interrupter
Moderation Interval can be changed within xhci addon, e.g. PCI
xhci_pci_setup().
[1], commit 0ebbab3742 ("USB: xhci: Ring allocation and initialization.")
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-31-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add xhci_dequeue_td() helper function to reduce code duplication.
Function xhci_dequeue_td() advances the dequeue pointer past the specified
Transfer Descriptor (TD) and releases the TD.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-30-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function is modified to return 'void' instead of an integer since it
invariably returns '0'. Additionally, multiple functions which only
return xhci_td_cleanup() are also refactored to return void.
This change eliminates the need for callers to handle a return value that
does not convey meaningful information and improve code readability, as it
becomes immediately clear that the function does not produce a significant
output.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-29-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Function td_to_noop() does not utilize arguments 'xhci' and 'ep_ring'.
These unused arguments are removed to clean up the code.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-28-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove redundant TRB cycle reset, the TRB cycle is already set to zero by
the preceding memset(), making the explicit reset unnecessary.
Clarify ring loop start point. Change the loop start from the dequeue
segment to the start segment. Both approaches achieve the same result,
but starting from the start segment makes it clearer that the entire ring
is being zeroed out.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-27-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variable 'max_interrupters' contains the maximum supported interrupters
or the maximum interrupters the user has requested. Thus, it should be
used instead of HCS_MAX_INTRS().
User set 'max_interrupters' value is validated in xhci_gen_setup(),
otherwise 'max_interrupters' value is 'HCS_MAX_INTRS(xhci->hcs_params1)'.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-26-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This quirk is old and seldom seen, as a result the trace is changed
to debug message and only printed when the quirk is set.
Move it into xhci_gen_setup() where the majority of quirks are set.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-25-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Old names:
* start_seg - last_trb_seg
* first_trb - last_trb
New names:
* start_seg - end_seg
* start_trb - end_trb
A Transfer Descriptor (TD) in the xhci driver is a data structure that
represents a single transaction to be performed by the USB host controller.
This transaction is defined by TRBs from 'start_trb' in 'start_seg' to
'end_trb' in 'end_seg'.
The terms "start" and "end" were chosen over "first" and "last" for ease
of searching within the codebase. The ring structure uses 'first_seg' and
'last_seg', while the TD structure uses 'start_seg' and 'end_seg'.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-24-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The definitions of vendor IDs follow the pattern PCI_VENDOR_ID_#vendor,
while device IDs — PCI_DEVICE_ID_#vendor_#device.
Update the ETRON device IDs to follow the above mentioned pattern.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-22-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit f8f80be501 ("xhci: Use soft retry to recover faster from
transaction errors"), unplugging USB device while enumeration results in
errors like this:
[ 364.855321] xhci_hcd 0000:0b:00.0: ERROR Transfer event for disabled endpoint slot 5 ep 2
[ 364.864622] xhci_hcd 0000:0b:00.0: @0000002167656d70 67f03000 00000021 0c000000 05038001
[ 374.934793] xhci_hcd 0000:0b:00.0: Abort failed to stop command ring: -110
[ 374.958793] xhci_hcd 0000:0b:00.0: xHCI host controller not responding, assume dead
[ 374.967590] xhci_hcd 0000:0b:00.0: HC died; cleaning up
[ 374.973984] xhci_hcd 0000:0b:00.0: Timeout while waiting for configure endpoint command
Seems that Etorn xHCI host can not perform Soft Retry correctly, apply
XHCI_NO_SOFT_RETRY quirk to disable Soft Retry and then issue is gone.
This patch depends on commit a4a251f8c2 ("usb: xhci: do not perform
Soft Retry for some xHCI hosts").
Fixes: f8f80be501 ("xhci: Use soft retry to recover faster from transaction errors")
Cc: stable@vger.kernel.org
Signed-off-by: Kuangyi Chiang <ki.chiang65@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-21-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Performing a stability stress test on a USB3.0 2.5G ethernet adapter
results in errors like this:
[ 91.441469] r8152 2-3:1.0 eth3: get_registers -71
[ 91.458659] r8152 2-3:1.0 eth3: get_registers -71
[ 91.475911] r8152 2-3:1.0 eth3: get_registers -71
[ 91.493203] r8152 2-3:1.0 eth3: get_registers -71
[ 91.510421] r8152 2-3:1.0 eth3: get_registers -71
The r8152 driver will periodically issue lots of control-IN requests
to access the status of ethernet adapter hardware registers during
the test.
This happens when the xHCI driver enqueue a control TD (which cross
over the Link TRB between two ring segments, as shown) in the endpoint
zero's transfer ring. Seems the Etron xHCI host can not perform this
TD correctly, causing the USB transfer error occurred, maybe the upper
driver retry that control-IN request can solve problem, but not all
drivers do this.
| |
-------
| TRB | Setup Stage
-------
| TRB | Link
-------
-------
| TRB | Data Stage
-------
| TRB | Status Stage
-------
| |
To work around this, the xHCI driver should enqueue a No Op TRB if
next available TRB is the Link TRB in the ring segment, this can
prevent the Setup and Data Stage TRB to be breaked by the Link TRB.
Check if the XHCI_ETRON_HOST quirk flag is set before invoking the
workaround in xhci_queue_ctrl_tx().
Fixes: d0e96f5a71 ("USB: xhci: Control transfer support.")
Cc: stable@vger.kernel.org
Signed-off-by: Kuangyi Chiang <ki.chiang65@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-20-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sometimes the hub driver does not recognize the USB device connected
to the external USB2.0 hub when the system resumes from S4.
After the SetPortFeature(PORT_RESET) request is completed, the hub
driver calls the HCD reset_device callback, which will issue a Reset
Device command and free all structures associated with endpoints
that were disabled.
This happens when the xHCI driver issue a Reset Device command to
inform the Etron xHCI host that the USB device associated with a
device slot has been reset. Seems that the Etron xHCI host can not
perform this command correctly, affecting the USB device.
To work around this, the xHCI driver should obtain a new device slot
with reference to commit 651aaf36a7 ("usb: xhci: Handle USB transaction
error on address command"), which is another way to inform the Etron
xHCI host that the USB device has been reset.
Add a new XHCI_ETRON_HOST quirk flag to invoke the workaround in
xhci_discover_or_reset_device().
Fixes: 2a8f82c4ce ("USB: xhci: Notify the xHC when a device is reset.")
Cc: stable@vger.kernel.org
Signed-off-by: Kuangyi Chiang <ki.chiang65@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-19-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Combine two if statements, because these hosts have the same
quirk flags applied.
[Mathias: has stable tag because other fixes in series depend on this]
Fixes: 91f7a1524a ("xhci: Apply broken streams quirk to Etron EJ188 xHCI host")
Cc: stable@vger.kernel.org
Signed-off-by: Kuangyi Chiang <ki.chiang65@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-18-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A ring consists of a list of segments, each containing a specific number of
TRBs. The xhci driver allocates and initializes ring segments and TRBs in
the same functions. This combined allocation and initialization process
leads to an issue where, after hibernation (S4 state), the xhci driver
frees all its memory and re-creates the rings, segments, and TRBs from
scratch.
Move all default ring segment initialization into function
xhci_initialize_ring_segments(). This function can be called to
reinitialize a ring without freeing and reallocating it.
Since xhci_alloc_segments_for_ring() no longer initializes segment TRBs,
xhci_initialize_ring_segments() is added to xhci_ring_expansion(). This
results in the last segment of the source ring having the 'LINK_TOGGLE'
bit set. Therefore, if the last source ring segment is not the last in
the destination ring, the 'LINK_TOGGLE' bit must be cleared.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-17-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prepare for splitting ring segments allocation and initialization by
reworking the xhci_link_segments() function. Segment linking and ring type
checks are moved out of xhci_link_segments(), and the function is renamed
to "xhci_set_link_trb()".
The goal is to keep ring linking within xhci_alloc_segments_for_ring() and
move initialization into a separate function.
Additionally, reorder and simplify xhci_set_link_trb() for better
readability.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-16-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor the xhci_link_rings() function to accept two rings: a source ring
and a destination ring. Previously, the function accepted a ring and a
segment list as arguments, now the function splices the source ring segment
list into the destination ring. This new approach reduces the number of
arguments and simplifies the code, making it easier to follow.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-15-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The segment list is only relevant within the context of the ring.
Thus, it is more logical to pass the ring itself when freeing all segments
from a ring, rather than passing the ring list.
Rename the function to "xhci_ring_segments_free" to align with the naming
convention of xhci_segment_free().
To make the freeing process more intuitive, free segments sequentially
from start to end (i.e., 0, 1, 2, 3, ...) instead of freeing the first
segment last (i.e., 1, 2, 3, ... 0).
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-14-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function xhci_alloc_segments_for_ring() currently takes 7 arguments,
5 of which are components of the 'xhci_ring' struct. Refactor the function
to accept a pointer to the 'xhci_ring' struct instead of passing these
components separately.
The change reduces the number of arguments, making the function signature
cleaner and easier to understand.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-13-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TRB cycle bit indicates TRB ownership by the Host Controller (HC) or
Host Controller Driver (HCD). New rings are initialized with 'cycle_state'
equal to one, and all its TRBs' cycle bits are set to zero. When handling
ring expansion, set the source ring cycle bits to the same value as the
destination ring.
Move the cycle bit setting from xhci_segment_alloc() to xhci_link_rings(),
and remove the 'cycle_state' argument from xhci_initialize_ring_info().
The xhci_segment_alloc() function uses kzalloc_node() to allocate segments,
ensuring that all TRB cycle bits are initialized to zero.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-12-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add macro to streamline and standardize the iteration over ring
segment list.
xhci_for_each_ring_seg(): Iterates over the entire ring segment list.
The xhci_free_segments_for_ring() function's while loop has not been
updated to use the new macro. This function has some underlying issues,
and as a result, it will be handled separately in a future patch.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-11-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ring data structure of each xHCI endpoint might stop sending
data due to the virt endpoint state.
Show the virt endpoint state within the endpoint context via debugfs
to facilitate debugging.
Co-developed-by: Xu Rao <raoxu@uniontech.com>
Signed-off-by: Xu Rao <raoxu@uniontech.com>
Signed-off-by: WangYuli <wangyuli@uniontech.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-10-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A successful 'Set TR Deq' command writes a new dequeue pointer to the
stream context for stream rings, show the content of the stream ctx
at command completion.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-9-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Show stream id, stream context type (SCT), ring dequeue pointer and
the DMA address of the stream context during stream allocation
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't trace ring pointers every time driver increases enqueue pointer
after queuing a TRB, or dequeue pointer after handling an event.
These xhci_inc_deq: and xhci_inc_enq: trace entries fill up the trace and
provides little useful info now that the TRB DMA address is printed with
the TRB itself.
Only trace ring during xhci_inc_enq() and xhci_inc_deq() in case we move
to a new ring segment.
Also don't show both segment and TRB addess in trace.
Segment is just TRB with 0xfff masked off.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DMA address of a queued TRB is essential when looking at traces as
both transfer events and command completion events refer to the command
or transfer based on its DMA address.
Previously the TRB address was figured out from xhci_inc_enq and
xhci_inc_deq trace entries seen after queuing or handlong a TRB.
Now that DMA address is shown in TRB tracing we can get rid of most of the
xhci_inc_enq and xhci_inc_deq traces thus decreasing trace size.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This function is supposed to sum the lengths of all transfer TRBs in
a TD up to a point, but it starts summing at the current dequeue since
it only ever gets called on the first pending TD.
This won't work when there are cancelled TDs at the beginning of the
ring. The function tries to exclude No-Ops from the count, but not all
cancelled TDs are No-Op'ed - not those the HW stopped on.
The absolutely obvious fix is to start counting at the TD's first TRB.
And remove the now-useless 'ring' parameter, and 'xhci' too.
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function has two parameters which it doesn't use and hasn't ever
used. One caller even puts NULL there, knowing it will work anyway.
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In addition to Normal TRB fields the Isoch TRBs have a SIA flag,
Frame ID, TLBPC and TBC fields.
Add these fields to tracing output
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The is_bin_visible() callbacks should not modify the struct
bin_attribute passed as argument.
Enforce this by marking the argument as const.
As there are not many callback implementers perform this change
throughout the tree at once.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Jason Gunthorpe <jgg@nvidia.com>
Acked-by: Ira Weiny <ira.weiny@intel.com>
Acked-by: Krzysztof Wilczyński <kw@linux.com>
Link: https://lore.kernel.org/r/20241103-sysfs-const-bin_attr-v2-5-71110628844c@weissschuh.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "*cmd" variable can be controlled by the user via debugfs. That means
"new_cam" can be as high as 255 while the size of the uc->updated[] array
is UCSI_MAX_ALTMODES (30).
The call tree is:
ucsi_cmd() // val comes from simple_attr_write_xsigned()
-> ucsi_send_command()
-> ucsi_send_command_common()
-> ucsi_run_command() // calls ucsi->ops->sync_control()
-> ucsi_ccg_sync_control()
Fixes: 170a6726d0 ("usb: typec: ucsi: add support for separate DP altmode devices")
Cc: stable <stable@kernel.org>
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/325102b3-eaa8-4918-a947-22aca1146586@stanley.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the device was already runtime suspended then during system suspend
we cannot access the device registers else it will crash.
Also we cannot access any registers after dwc3_core_exit() on some
platforms so move the dwc3_enable_susphy() call to the top.
Cc: stable@vger.kernel.org # v5.15+
Reported-by: William McVicker <willmcvicker@google.com>
Closes: https://lore.kernel.org/all/ZyVfcUuPq56R2m1Y@google.com
Fixes: 705e3ce37b ("usb: dwc3: core: Fix system suspend on TI AM62 platforms")
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Tested-by: Will McVicker <willmcvicker@google.com>
Link: https://lore.kernel.org/r/20241104-am62-lpm-usb-fix-v1-1-e93df73a4f0d@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the read of USB_PDPHY_RX_ACKNOWLEDGE_REG failed, then hdr_len and
txbuf_len are uninitialized. This commit stops to print uninitialized
value and misleading/false data.
Cc: stable@vger.kernel.org
Fixes: a4422ff221 (" usb: typec: qcom: Add Qualcomm PMIC Type-C driver")
Signed-off-by: Rex Nie <rex.nie@jaguarmicro.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Acked-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20241030133632.2116-1-rex.nie@jaguarmicro.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 6ed05c68cb ("usb: musb: sunxi: Explicitly release USB PHY on
exit") will cause that usb phy @glue->xceiv is accessed after released.
1) register platform driver @sunxi_musb_driver
// get the usb phy @glue->xceiv
sunxi_musb_probe() -> devm_usb_get_phy().
2) register and unregister platform driver @musb_driver
musb_probe() -> sunxi_musb_init()
use the phy here
//the phy is released here
musb_remove() -> sunxi_musb_exit() -> devm_usb_put_phy()
3) register @musb_driver again
musb_probe() -> sunxi_musb_init()
use the phy here but the phy has been released at 2).
...
Fixed by reverting the commit, namely, removing devm_usb_put_phy()
from sunxi_musb_exit().
Fixes: 6ed05c68cb ("usb: musb: sunxi: Explicitly release USB PHY on exit")
Cc: stable@vger.kernel.org
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20241029-sunxi_fix-v1-1-9431ed2ab826@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The use of (of|device)_property_read_bool() for non-boolean properties
is deprecated in favor of of_property_present() when testing for
property presence.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Acked-by: Peter Chen <peter.chen@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20241104190820.277702-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the USB fixes in here as well, and this resolves a merge
conflict in:
drivers/usb/typec/tcpm/tcpm.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://lore.kernel.org/r/20241101150730.090dc30f@canb.auug.org.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit fde192511b ("kconfig: remove tristate choice support"),
all choice blocks are now boolean. There is no longer a need to specify
the choice type explicitly.
Most choice blocks already use "prompt". Before the next commit removes
support for the "bool" syntax in choice entries, this commit converts
the remaining "bool" occurences under drivers/usb/.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
The TUSB1046-DCI is a USB-C linear redriver crosspoint switch, which can
mux SuperSpeed lanes from a Type-C connector to a USB3.0 data lane or up to
4 display port lanes.
Add support for driving the TUSB1046 as a Type-C orientation switch and
DisplayPort altmode multiplexer.
Signed-off-by: Romain Gantois <romain.gantois@bootlin.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20241024-tusb1046-v2-2-d031b1a43e6d@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some PCIe-to-USB controllers such as TI's TUSB73x0 3.0 xHCI host
controller supports controlling the PWRONx polarity via the USB control
register (E0h). Add support for device tree property
ti,pwron-active-high which indicates PWRONx to be active high and
configure the E0h register accordingly. This enables the software
control for the TUSB73x0's PWRONx outputs with an inverted polarity from
the default configuration which could be used as USB EN signals for the
other hubs or devices.
Signed-off-by: Parth Pancholi <parth.pancholi@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://lore.kernel.org/r/20241029072444.8827-3-francesco@dolcini.it
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_gpio.h is deprecated and subject to remove. The drivers in question
don't use it, simply remove the unused header.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20241031103818.2451816-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "dev_dbg(&urb->dev->dev, ..." which happens after usb_free_urb(urb)
is a use after free of the "urb" pointer. Store the "dev" pointer at the
start of the function to avoid this issue.
Fixes: 984f686832 ("USB: serial: io_edgeport.c: remove dbg() usage")
Cc: stable@vger.kernel.org
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
PD3.1 spec ("8.3.3.3.3 PE_SNK_Wait_for_Capabilities State") mandates
that the policy engine perform a hard reset when SinkWaitCapTimer
expires. Instead the code explicitly does a GET_SOURCE_CAP when the
timer expires as part of SNK_WAIT_CAPABILITIES_TIMEOUT. Due to this the
following compliance test failures are reported by the compliance tester
(added excerpts from the PD Test Spec):
* COMMON.PROC.PD.2#1:
The Tester receives a Get_Source_Cap Message from the UUT. This
message is valid except the following conditions: [COMMON.PROC.PD.2#1]
a. The check fails if the UUT sends this message before the Tester
has established an Explicit Contract
...
* TEST.PD.PROT.SNK.4:
...
4. The check fails if the UUT does not send a Hard Reset between
tTypeCSinkWaitCap min and max. [TEST.PD.PROT.SNK.4#1] The delay is
between the VBUS present vSafe5V min and the time of the first bit
of Preamble of the Hard Reset sent by the UUT.
For the purpose of interoperability, restrict the quirk introduced in
https://lore.kernel.org/all/20240523171806.223727-1-sebastian.reichel@collabora.com/
to only non self-powered devices as battery powered devices will not
have the issue mentioned in that commit.
Cc: stable@vger.kernel.org
Fixes: 122968f8dd ("usb: typec: tcpm: avoid resets for missing source capability messages")
Reported-by: Badhri Jagan Sridharan <badhri@google.com>
Closes: https://lore.kernel.org/all/CAPTae5LAwsVugb0dxuKLHFqncjeZeJ785nkY4Jfd+M-tCjHSnQ@mail.gmail.com/
Signed-off-by: Amit Sunil Dhamne <amitsd@google.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Xu Yang <xu.yang_2@nxp.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20241024022233.3276995-1-amitsd@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For devm_usb_put_phy(), its comment says it needs to invoke usb_put_phy()
to release the phy, but it does not do that actually, so it can not fully
undo what the API devm_usb_get_phy() does, that is wrong, fixed by using
devres_release() instead of devres_destroy() within the API.
Fixes: cedf860237 ("usb: phy: move bulk of otg/otg.c to phy/phy.c")
Cc: stable@vger.kernel.org
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20241020-usb_phy_fix-v1-1-7f79243b8e1e@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Follow the advice in Documentation/filesystems/sysfs.rst:
show() should only use sysfs_emit() or sysfs_emit_at() when formatting
the value to be returned to user space.
Signed-off-by: Jiayi Li <lijiayi@kylinos.cn>
Link: https://lore.kernel.org/r/20241023085429.2865488-1-lijiayi@kylinos.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for DT time properties to allow users to define platform
specific timing deadlines of certain timers rather than using hardcoded
ones. For values that have not been explicitly defined in DT using this
property, default values will be set therefore, making this change
backward compatible.
Signed-off-by: Amit Sunil Dhamne <amitsd@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20241022-pd-dt-time-props-v1-2-fea96f51b302@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current logic is rigid, setting num_fifos to fixed values.
3 for any maxburst greater than 1.
tx_fifo_resize_max_num for maxburst greater than 6.
Additionally, it did not differentiate much between bulk and
isochronous transfers, applying similar logic to both.
The updated logic is more flexible and specifically designed to meet
the unique requirements of both bulk and isochronous transfers. We
have made every effort to satisfy all needs and requirements, verified
on our specific platform and application.
Bulk Transfers: Ensures that num_fifos is optimized by considering both
the maxburst and DT property "tx-fifo-max-num" for super speed and
above. For high-speed and below bulk endpoints, a 2K TxFIFO allocation
is used to meet efficient data transfer needs, considering
FIFO-constrained platforms.
Isochronous Transfers: Ensures that num_fifos is sufficient by
considering the maximum packet multiplier for HS and below and maxburst
for Super-speed and above eps, along with a constraint with the DT
property "tx-fifo-max-num".
This change aims to optimize the allocation of Tx FIFOs for both bulk
and isochronous endpoints, potentially improving data transfer efficiency
and overall performance. It also enhances support for all use cases,
which can be tweaked with DT parameters and the endpoint’s maxburst and
maxpacket. This structured approach ensures that the appropriate number
of FIFOs is allocated based on the endpoint type and USB speed.
Signed-off-by: Akash Kumar <quic_akakum@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20241017064423.7056-1-quic_akakum@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
That command is executed from several locations in the
driver, so providing a dedicated helper function for it.
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20241017091112.1178509-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the __free() macro for 'altmodes_node' to automatically release the
node when it goes out of scope, removing the need for explicit calls to
fwnode_handle_put().
Suggested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20241021-typec-class-fwnode_handle_put-v2-2-3281225d3d27@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'altmodes_node' fwnode_handle is never released after it is no
longer required, which leaks the resource.
Add the required call to fwnode_handle_put() when 'altmodes_node' is no
longer required.
Cc: stable@vger.kernel.org
Fixes: 7b458a4c5d ("usb: typec: Add typec_port_register_altmodes()")
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://lore.kernel.org/r/20241021-typec-class-fwnode_handle_put-v2-1-3281225d3d27@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If drm_dp_hpd_bridge_register() fails, the probe function returns
without removing the fwnode via fwnode_handle_put(), leaking the
resource.
Jump to fwnode_remove if drm_dp_hpd_bridge_register() fails to remove
the fwnode acquired with device_get_named_child_node().
Cc: stable@vger.kernel.org
Fixes: 7d9f1b72b2 ("usb: typec: qcom-pmic-typec: switch to DRM_AUX_HPD_BRIDGE")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20241020-qcom_pmic_typec-fwnode_remove-v2-2-7054f3d2e215@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The right function to release a fwnode acquired via
device_get_named_child_node() is fwnode_handle_put(), and not
fwnode_remove_software_node(), as no software node is being handled.
Replace the calls to fwnode_remove_software_node() with
fwnode_handle_put() in qcom_pmic_typec_probe() and
qcom_pmic_typec_remove().
Cc: stable@vger.kernel.org
Fixes: a4422ff221 ("usb: typec: qcom: Add Qualcomm PMIC Type-C driver")
Suggested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Acked-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20241020-qcom_pmic_typec-fwnode_remove-v2-1-7054f3d2e215@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix a boot hang issue triggered when a USB3 device is incorrectly assumed
to be tunneled over USB4, thus attempting to create a device link between
the USB3 "consumer" device and the USB4 "supplier" Host Interface before
the USB4 side is properly bound to a driver.
This could happen if xhci isn't capable of detecting tunneled devices,
but ACPI tables contain all info needed to assume device is tunneled.
i.e. udev->tunnel_mode == USB_LINK_UNKNOWN.
It turns out that even for actual tunneled USB3 devices it can't be
assumed that the thunderbolt driver providing the tunnel is loaded
before the tunneled USB3 device is created.
The tunnel can be created by BIOS and remain in use by thunderbolt/USB4
host driver once it loads.
Solve this by making the device link "stateless", which doesn't create
a driver presence order dependency between the supplier and consumer
drivers.
It still guarantees correct suspend/resume and shutdown ordering.
cc: Mario Limonciello <mario.limonciello@amd.com>
Fixes: f1bfb4a6fe ("usb: acpi: add device link between tunneled USB3 device and USB4 Host Interface")
Tested-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20241024131355.3836538-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit d483f034f0 ("usb: dwc2: Skip clock gating on Broadcom SoCs")
introduced a regression on Raspberry Pi 3 B Plus, which prevents
enumeration of the onboard Microchip LAN7800 in case no external USB device
is connected during boot.
Fixes: d483f034f0 ("usb: dwc2: Skip clock gating on Broadcom SoCs")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/20241025103621.4780-2-wahrenst@gmx.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During the aborting of a command, the software receives a command
completion event for the command ring stopped, with the TRB pointing
to the next TRB after the aborted command.
If the command we abort is located just before the Link TRB in the
command ring, then during the 'command ring stopped' completion event,
the xHC gives the Link TRB in the event's cmd DMA, which causes a
mismatch in handling command completion event.
To address this situation, move the 'command ring stopped' completion
event check slightly earlier, since the specific command it stopped
on isn't of significant concern.
Fixes: 7f84eef0da ("USB: xhci: No-op command queueing and irq handler.")
Cc: stable@vger.kernel.org
Signed-off-by: Faisal Hassan <quic_faisalh@quicinc.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241022155631.1185-1-quic_faisalh@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use pm_runtime_put in the remove function and pm_runtime_get to disable
RPM on platforms that don't support runtime D3, as re-enabling it through
sysfs auto power control may cause the controller to malfunction. This
can lead to issues such as hotplug devices not being detected due to
failed interrupt generation.
Fixes: a5d6264b63 ("xhci: Enable RPM on controllers that support low-power states")
Cc: stable <stable@kernel.org>
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20241024133718.723846-1-Basavaraj.Natikar@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some new modem device ids.
Everything has been in linux-next over night with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCZxIyrQAKCRALxc3C7H1l
CCgGAQDkVANkAOTEq8zOfpaULkWkMJXMRzd28YrkCqlgJfbkYQEAjTWtz8F48Ne7
V9CYj/dbNULlQ0Q+kqKqGBcKdZrq2AI=
=/sNu
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-6.12-rc4' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial device ids for 6.12-rc4
Here are some new modem device ids.
Everything has been in linux-next over night with no reported issues.
* tag 'usb-serial-6.12-rc4' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add Telit FN920C04 MBIM compositions
USB: serial: option: add support for Quectel EG916Q-GL
Treat each completed full size write to /dev/ttyDBC0 as a separate usb
transfer. Make sure the size of the TRBs matches the size of the tty
write by first queuing as many max packet size TRBs as possible up to
the last TRB which will be cut short to match the size of the tty write.
This solves an issue where userspace writes several transfers back to
back via /dev/ttyDBC0 into a kfifo before dbgtty can find available
request to turn that kfifo data into TRBs on the transfer ring.
The boundary between transfer was lost as xhci-dbgtty then turned
everyting in the kfifo into as many 'max packet size' TRBs as possible.
DbC would then send more data to the host than intended for that
transfer, causing host to issue a babble error.
Refuse to write more data to kfifo until previous tty write data is
turned into properly sized TRBs with data size boundaries matching tty
write size
Tested-by: Uday M Bhat <uday.m.bhat@intel.com>
Tested-by: Łukasz Bartosik <ukaszb@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241016140000.783905-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some host controllers fail to produce the final completion event on an
isochronous TD which experienced an error mid TD. We deal with it by
flagging such TDs and checking if the next event points at the flagged
TD or at the next one, and giving back the flagged TD if the latter.
This is not enough, because the next TD may be missed by the xHC. Or
there may be no next TD but a ring underrun. We also need to get such
TD quickly out of the way, or errors on later TDs may be handled wrong.
If the next TD experiences a Missed Service Error, we will set the skip
flag on the endpoint and then attempt skipping TDs when yet another
event arrives. In such scenario, we ought to report the 'error mid TD'
transfer as such rather than skip it.
Another problem case are Stopped events. If we see one after an error
mid TD, we naively assume that it's a Force Stopped Event because it
doesn't match the pending TD, but in reality it might be an ordinary
Stopped event for the next TD, which we fail to recognize and handle.
Fix this by moving error mid TD handling before the whole TD skipping
loop. Remove unnecessary conditions, always give back the TD if the new
event points to any TRB outside it or if the pointer is NULL, as may be
the case in Ring Underrun and Overrun events on 1st gen hardware. Only
if the pending TD isn't flagged, consider other actions like skipping.
As a side effect of reordering with skip and FSE cases, error mid TD is
reordered with last_td_was_short check. This is harmless, because the
two cases are mutually exclusive - only one can happen in any given run
of handle_tx_event().
Tested on the NEC host and a USB camera with flaky cable. Dynamic debug
confirmed that Transaction Errors are sometimes seen, sometimes mid-TD,
sometimes followed by Missed Service. In such cases, they were finished
properly before skipping began.
[Rebase on 6.12-rc1 -Mathias]
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241016140000.783905-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Avoid xHC host from processing a cancelled URB by always turning
cancelled URB TDs into no-op TRBs before queuing a 'Set TR Deq' command.
If the command fails then xHC will start processing the cancelled TD
instead of skipping it once endpoint is restarted, causing issues like
Babble error.
This is not a complete solution as a failed 'Set TR Deq' command does not
guarantee xHC TRB caches are cleared.
Fixes: 4db356924a ("xhci: turn cancelled td cleanup to its own function")
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241016140000.783905-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The stream contex type (SCT) bitfield is used both in the stream context
data structure, and in the 'Set TR Dequeue pointer' command TRB.
In both cases it uses bits 3:1
The SCT_FOR_TRB(p) macro used to set the stream context type (SCT) field
for the 'Set TR Dequeue pointer' command TRB incorrectly shifts the value
1 bit left before masking the three bits.
Fix this by first masking and rshifting, just like the similar
SCT_FOR_CTX(p) macro does
This issue has not been visibile as the lost bit 3 is only used with
secondary stream arrays (SSA). Xhci driver currently only supports using
a primary stream array with Linear stream addressing.
Fixes: 95241dbdf8 ("xhci: Set SCT field for Set TR dequeue on streams")
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241016140000.783905-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The syzbot fuzzer has been encountering "task hung" problems ever
since the dummy-hcd driver was changed to use hrtimers instead of
regular timers. It turns out that the problems are caused by a subtle
difference between the timer_pending() and hrtimer_active() APIs.
The changeover blindly replaced the first by the second. However,
timer_pending() returns True when the timer is queued but not when its
callback is running, whereas hrtimer_active() returns True when the
hrtimer is queued _or_ its callback is running. This difference
occasionally caused dummy_urb_enqueue() to think that the callback
routine had not yet started when in fact it was almost finished. As a
result the hrtimer was not restarted, which made it impossible for the
driver to dequeue later the URB that was just enqueued. This caused
usb_kill_urb() to hang, and things got worse from there.
Since hrtimers have no API for telling when they are queued and the
callback isn't running, the driver must keep track of this for itself.
That's what this patch does, adding a new "timer_pending" flag and
setting or clearing it at the appropriate times.
Reported-by: syzbot+f342ea16c9d06d80b585@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/linux-usb/6709234e.050a0220.3e960.0011.GAE@google.com/
Tested-by: syzbot+f342ea16c9d06d80b585@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: a7f3813e58 ("usb: gadget: dummy_hcd: Switch to hrtimer transfer scheduler")
Cc: Marcello Sylvester Bauer <sylv@sylv.io>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/2dab644e-ef87-4de8-ac9a-26f100b2c609@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Expose xhci_stop_endpoint_sync() which is a synchronous variant of
xhci_queue_stop_endpoint(). This is useful for client drivers that are
using the secondary interrupters, and need to stop the current endpoint
session.
This does not go through the normal xhci_handle_cmd_stop_ep() command
completion handler, because it utilizes the completion path to achieve
synchronous behavior. Users of this API are primarily intended to be
clients that maintain their own transfer rings, such as in the case of USB
audio offload.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20241015212915.1206789-3-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the streamoff call was triggered by some previous disconnect
or userspace application shutdown the uvc_function_setup_continue
should not be called and the state should not be overwritten.
For this situation the set_alt(0) was never called and the streaming ep
has no USB_GADGET_DELAYED_STATUS pending.
Since the state then was already updated before we also omit the state
update.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20240403-uvc_request_length_by_interval-v7-9-e224bb1035f0@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is adding trace events for each request that is being
enqueued into the hw and will be completed. This way it is possible
to track the fill status of the gadget hardware and find potential
issues.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20240403-uvc_request_length_by_interval-v7-8-e224bb1035f0@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We set the minimum amount of v4l2 buffers that is possibly be pending
to UVCG_STREAMING_MIN_BUFFERS which is two. This way the driver will
always have at least one frame pending to be encoded while the other
is being enqueued in the hardware.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20240403-uvc_request_length_by_interval-v7-7-e224bb1035f0@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Compressed formats generate content depending amount of data that is set
in the vb2 buffer by the payload_size. When streaming those formats it
is better to scatter that smaller data over all requests. This patch is
doing that by introducing the calculated req_payload_size which is
updated by each frame. It the uses this amount of data to fill the
isoc requests instead of the video->req_size.
For uncompressed formats it will not make a difference since the payload
size will be equal to the imagesize. Therefore the code will have no
effecta as req_payload_size will be equal to req_size.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20240403-uvc_request_length_by_interval-v7-6-e224bb1035f0@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is removing the initial imprecise and limited calculation of
requests needed to be used from the queue_setup callback. It instead
introduces the uvc_video_prep_requests function which is called
immediately before the request allocation.
With the information of the usb frame interval length it is possible to
calculate the number of requests needed during one frame duration.
Based on the calculated number of requests and the imagesize we
calculate the actual size per request. This calculation has the benefit
that the frame data is equally distributed over all allocated requests.
When the req_size is not in the range for the actually configured
max_req_size configured for the overall bandwidth we fallback
to use the max_req_size instead.
Since this calculations are only important for isoc transfers we just
use max_request_size for bulk and skip it.
As video->req_size will be recalculated on every video_enable resetting
it to 0 is not necessary anymore.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20240403-uvc_request_length_by_interval-v7-5-e224bb1035f0@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The uvc gadget driver is lacking the information which frame interval
was set by the host. We add this information by implementing the g_parm
and s_parm callbacks.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20240403-uvc_request_length_by_interval-v7-4-e224bb1035f0@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We install an kthread with pfifo priority that is iterating over all
prepared requests and keeps the isoc queue busy. This way it will be
scheduled with the same priority as the interrupt handler.
As the kthread is triggered with video_enable it will immediately
queue some zero length requests into the hw if there is no buffer data
available. It also watches the level of needed zero length requests in
the hardware not to fall under the UVCG_REQ_MAX_ZERO_COUNT threshold.
This way we can drop the function uvc_video_ep_queue_initial_requests
entirely.
By using the kthread to do the actual request handling the interrupt
handler will not be running into the time consuming and eventually
locking work of actually enqueueing the requests back into its own
pipeline. This work can now even be scheduled on another cpu.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20240403-uvc_request_length_by_interval-v7-3-e224bb1035f0@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The complete handler will at least be called after 16 requests have
completed, but will still handle all finisher requests. Since we have
to maintain a costant filling in the isoc queue we ensure this by
adding zero length requests.
By counting the amount enqueued requests we can ensure that the queue is
never underrun and only need to get active if the queue is running
critical. This patch is setting 32 as the critical level, which
is twice the request amount that is needed to create interrupts.
To properly solve the amount of zero length requests that needs to
be held in the hardware after one interrupt needs to be measured
and depends on the runtime of the first enqueue run after the interrupt
triggered. For now we just use twice the amount of requests between an
interrupt.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20240403-uvc_request_length_by_interval-v7-2-e224bb1035f0@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the req_free list will updated if enqueuing one request was not
possible it will be added back to the free list. With every available
free request in the queue it is a valid case for the pump worker to use
it and continue the pending bufferdata into requests for the req_ready
list.
Fixes: 6acba0345b ("usb:gadget:uvc Do not use worker thread to pump isoc usb requests")
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20240403-uvc_request_length_by_interval-v7-1-e224bb1035f0@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UCSI does not share the contents of the Enter_USB Message
that was used, so the active mode still has to be always
determined from the enumerated USB device. However, after
UCSI v2.0 it is possible to check separately is USB4 the
active mode.
So with USB2 and USB3 the mode is always determined from the
result of the USB enumeration, and when USB4 USB Mode is
active, UCSI driver can assign the mode directly.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20241016131834.898599-5-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB capabilities can be extracted from the response to
the Get Connector Capability command. USB2 and USB3 support
can be checked from the Operation Mode field, and USB4
support from the Extended Operation Mode field.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> # SM8450-HDK
Link: https://lore.kernel.org/r/20241016131834.898599-4-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This attribute file shows the supported USB modes (USB 2.0,
USB 3.0 and USB4) of the partner, and the currently active
mode.
The active mode is determined primarily by checking the
speed of the enumerated USB device. When USB Power Delivery
is supported, the active USB mode should be always the mode
that was used with the Enter_USB Message, regardless of the
result of the USB enumeration. The port drivers can
separately assign the mode with a dedicated API.
If USB Power Delivery Identity is supplied for the partner
device, the supported modes are extracted from it.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20241016131834.898599-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This attribute file, named "usb_capability", will show the
supported USB modes, which are USB 2.0, USB 3.2 and USB4.
These modes are defined in the USB Type-C (R2.0) and USB
Power Delivery (R3.0 V2.0) Specifications.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20241016131834.898599-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usbdev_mmap() creates VMAs which can only be used through
usbdev_do_ioctl(), which requires FMODE_WRITE; so usbdev_mmap() is only
useful with FMODE_WRITE.
On typical Linux systems, files at /dev/bus/usb/*/* are mode 0664, so
UIDs without any special privileges can't use usbdev_do_ioctl(), but
they can still execute the usbdev_mmap() codepath.
Check for FMODE_WRITE in usbdev_mmap() to reduce attack surface a little
bit.
Signed-off-by: Jann Horn <jannh@google.com>
Link: https://lore.kernel.org/r/20241016-usbdev-mmap-require-write-v1-1-6f8256414d5c@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for frame-based frame format, which can be used to support
multiple formats like H264 or H265, in addition to MJPEG and YUV frames.
The frame-based format is set to H264 by default, but it can be updated
to other formats by modifying the GUID through the guid configfs
attribute. Different structures are used for all three formats, as
H264 has a different structure compared to MJPEG and uncompressed
formats. These structures will be passed to the frame make function
based on the active format, using a common frame structure with
additional parameters needed only for frame-based formats. These
parameters are handled at runtime in the UVC driver.
Signed-off-by: Akash Kumar <quic_akakum@quicinc.com>
Link: https://lore.kernel.org/r/20240927152138.31416-1-quic_akakum@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The configfs store callback should return the number of bytes consumed
not the total number of bytes we actually stored. These could differ if
for example the passed in string had a newline we did not store.
If the returned value does not match the number of bytes written the
writer might assume a failure or keep trying to write the remaining bytes.
For example the following command will hang trying to write the final
newline over and over again (tested on bash 2.05b):
echo foo > function_name
Fixes: 993a44fa85 ("usb: gadget: f_uac2: allow changing interface name via configfs")
Cc: stable <stable@kernel.org>
Signed-off-by: Kevin Groeneveld <kgroeneveld@lenbrook.com>
Link: https://lore.kernel.org/r/20241006232637.4267-1-kgroeneveld@lenbrook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 6d73572206 ("usb: dwc3: core: Prevent phy suspend during init"),
system suspend is broken on AM62 TI platforms.
Before that commit, both DWC3_GUSB3PIPECTL_SUSPHY and DWC3_GUSB2PHYCFG_SUSPHY
bits (hence forth called 2 SUSPHY bits) were being set during core
initialization and even during core re-initialization after a system
suspend/resume.
These bits are required to be set for system suspend/resume to work correctly
on AM62 platforms.
Since that commit, the 2 SUSPHY bits are not set for DEVICE/OTG mode if gadget
driver is not loaded and started.
For Host mode, the 2 SUSPHY bits are set before the first system suspend but
get cleared at system resume during core re-init and are never set again.
This patch resovles these two issues by ensuring the 2 SUSPHY bits are set
before system suspend and restored to the original state during system resume.
Cc: stable@vger.kernel.org # v6.9+
Fixes: 6d73572206 ("usb: dwc3: core: Prevent phy suspend during init")
Link: https://lore.kernel.org/all/1519dbe7-73b6-4afc-bfe3-23f4f75d772f@kernel.org/
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Tested-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/r/20241011-am62-lpm-usb-v3-1-562d445625b5@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If USB virtualizatoin is enabled, USB2 ports are shared between all
Virtual Functions. The USB2 port number owned by an USB2 root hub in
a Virtual Function may be less than total USB2 phy number supported
by the Tegra XUSB controller.
Using total USB2 phy number as port number to check all PORTSC values
would cause invalid memory access.
[ 116.923438] Unable to handle kernel paging request at virtual address 006c622f7665642f
...
[ 117.213640] Call trace:
[ 117.216783] tegra_xusb_enter_elpg+0x23c/0x658
[ 117.222021] tegra_xusb_runtime_suspend+0x40/0x68
[ 117.227260] pm_generic_runtime_suspend+0x30/0x50
[ 117.232847] __rpm_callback+0x84/0x3c0
[ 117.237038] rpm_suspend+0x2dc/0x740
[ 117.241229] pm_runtime_work+0xa0/0xb8
[ 117.245769] process_scheduled_works+0x24c/0x478
[ 117.251007] worker_thread+0x23c/0x328
[ 117.255547] kthread+0x104/0x1b0
[ 117.259389] ret_from_fork+0x10/0x20
[ 117.263582] Code: 54000222 f9461ae8 f8747908 b4ffff48 (f9400100)
Cc: stable@vger.kernel.org # v6.3+
Fixes: a30951d31b ("xhci: tegra: USB2 pad power controls")
Signed-off-by: Henry Lin <henryl@nvidia.com>
Link: https://lore.kernel.org/r/20241014042134.27664-1-henryl@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DWC3 programming guide mentions that when operating in USB2.0 speeds,
if GUSB2PHYCFG[6] or GUSB2PHYCFG[8] is set, it must be cleared prior
to issuing commands and may be set again after the command completes.
But currently while issuing EndXfer command without CmdIOC set, we
wait for 1ms after GUSB2PHYCFG is restored. This results in cases
where EndXfer command doesn't get completed and causes SMMU faults
since requests are unmapped afterwards. Hence restore GUSB2PHYCFG
after waiting for EndXfer command completion.
Cc: stable@vger.kernel.org
Fixes: 1d26ba0944 ("usb: dwc3: Wait unconditionally after issuing EndXfer command")
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240924093208.2524531-1-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This line is overwriting the result of the above switch-case.
This fixes the tcpm driver getting stuck in a "Sink TX No Go" loop.
Fixes: a4422ff221 ("usb: typec: qcom: Add Qualcomm PMIC Type-C driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Acked-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20241005144146.2345-1-jonathan@marek.ca
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the extra semicolon after the
do {} while (0) in UVC_COPY_DESCRIPTOR macro.
Fix the following checkpatch.pl warning
WARNING: do {} while (0) macros should not be semicolon terminated
+#define UVC_COPY_DESCRIPTOR(mem, dst, desc) \
+ do { \
+ memcpy(mem, desc, (desc)->bLength); \
+ *(dst)++ = mem; \
+ mem += (desc)->bLength; \
+ } while (0);
Signed-off-by: Abhishek Tamboli <abhishektamboli9@gmail.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Link: https://lore.kernel.org/r/20241013142511.9946-1-abhishektamboli9@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ACPI _DSM methods are needed only for UCSI write operations and for reading
CCI during RESET_PPM operation. So, remove _DSM calls from other places.
While there, remove the Zenbook quirk also since the default behavior
now aligns with the Zenbook quirk. With this change, GET_CONNECTOR_STATUS
returns at least 6 seconds faster than before in Arrowlake-S platforms.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Saranya Gopal <saranya.gopal@intel.com>
Reviewed-by: Christian A. Ehrhardt <lk@c--e.de>
Link: https://lore.kernel.org/r/20240830084342.460109-1-saranya.gopal@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While design wise the idea of converting the driver to use
the hierarchy of the IRQ chips is correct, the implementation
has (inherited) flaws. This was unveiled when platform_get_irq()
had started WARN() on IRQ 0 that is supposed to be a Linux
IRQ number (also known as vIRQ).
Rework the driver to respect IRQ domain when creating each MFD
device separately, as the domain is not the same for all of them.
Fixes: 9c6235c863 ("mfd: intel_soc_pmic_bxtwc: Add bxt_wcove_usbc device")
Fixes: d2061f9cc3 ("usb: typec: add driver for Intel Whiskey Cove PMIC USB Type-C PHY")
Fixes: 57129044f5 ("mfd: intel_soc_pmic_bxtwc: Use chained IRQs for second level IRQ chips")
Reported-by: Zhang Ning <zhangn1985@outlook.com>
Closes: https://lore.kernel.org/r/TY2PR01MB3322FEDCDC048B7D3794F922CDBA2@TY2PR01MB3322.jpnprd01.prod.outlook.com
Tested-by: Zhang Ning <zhangn1985@outlook.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20241005193029.1929139-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Lee Jones <lee@kernel.org>
Here are some small USB fixes for some reported problems for 6.12-rc3.
Include in here is:
- fix for yurex driver that was caused in -rc1
- build error fix for usbg network filesystem code
- onboard_usb_dev build fix
- dwc3 driver fixes for reported errors
- gadget driver fix
- new USB storage driver quirk
- xhci resume bugfix
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZwu6fw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yly6QCfdXwmKEqG4H7xonERzmEkP9/sYtoAnAsafKV5
5pWgy7Jw+WH1s1L7IzGy
=xrG1
-----END PGP SIGNATURE-----
Merge tag 'usb-6.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB fixes for some reported problems for 6.12-rc3.
Include in here is:
- fix for yurex driver that was caused in -rc1
- build error fix for usbg network filesystem code
- onboard_usb_dev build fix
- dwc3 driver fixes for reported errors
- gadget driver fix
- new USB storage driver quirk
- xhci resume bugfix
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-6.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
net/9p/usbg: Fix build error
USB: yurex: kill needless initialization in yurex_read
Revert "usb: yurex: Replace snprintf() with the safer scnprintf() variant"
usb: xhci: Fix problem with xhci resume from suspend
usb: misc: onboard_usb_dev: introduce new config symbol for usb5744 SMBus support
usb: dwc3: core: Stop processing of pending events if controller is halted
usb: dwc3: re-enable runtime PM after failed resume
usb: storage: ignore bogus device raised by JieLi BR21 USB sound chip
usb: gadget: core: force synchronous registration
[Syzbot reported two possible deadlocks]
The first possible deadlock is:
WARNING: possible recursive locking detected
6.12.0-rc1-syzkaller-00027-g4a9fe2a8ac53 #0 Not tainted
--------------------------------------------
syz-executor363/2651 is trying to acquire lock:
ffffffff89b120e8 (chaoskey_list_lock){+.+.}-{3:3}, at: chaoskey_release+0x15d/0x2c0 drivers/usb/misc/chaoskey.c:322
but task is already holding lock:
ffffffff89b120e8 (chaoskey_list_lock){+.+.}-{3:3}, at: chaoskey_release+0x7f/0x2c0 drivers/usb/misc/chaoskey.c:299
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(chaoskey_list_lock);
lock(chaoskey_list_lock);
*** DEADLOCK ***
The second possible deadlock is:
WARNING: possible circular locking dependency detected
6.12.0-rc1-syzkaller-00027-g4a9fe2a8ac53 #0 Not tainted
------------------------------------------------------
kworker/0:2/804 is trying to acquire lock:
ffffffff899dadb0 (minor_rwsem){++++}-{3:3}, at: usb_deregister_dev+0x7c/0x1e0 drivers/usb/core/file.c:186
but task is already holding lock:
ffffffff89b120e8 (chaoskey_list_lock){+.+.}-{3:3}, at: chaoskey_disconnect+0xa8/0x2a0 drivers/usb/misc/chaoskey.c:235
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (chaoskey_list_lock){+.+.}-{3:3}:
__mutex_lock_common kernel/locking/mutex.c:608 [inline]
__mutex_lock+0x175/0x9c0 kernel/locking/mutex.c:752
chaoskey_open+0xdd/0x220 drivers/usb/misc/chaoskey.c:274
usb_open+0x186/0x220 drivers/usb/core/file.c:47
chrdev_open+0x237/0x6a0 fs/char_dev.c:414
do_dentry_open+0x6cb/0x1390 fs/open.c:958
vfs_open+0x82/0x3f0 fs/open.c:1088
do_open fs/namei.c:3774 [inline]
path_openat+0x1e6a/0x2d60 fs/namei.c:3933
do_filp_open+0x1dc/0x430 fs/namei.c:3960
do_sys_openat2+0x17a/0x1e0 fs/open.c:1415
do_sys_open fs/open.c:1430 [inline]
__do_sys_openat fs/open.c:1446 [inline]
__se_sys_openat fs/open.c:1441 [inline]
__x64_sys_openat+0x175/0x210 fs/open.c:1441
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xcd/0x250 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x77/0x7f
-> #0 (minor_rwsem){++++}-{3:3}:
check_prev_add kernel/locking/lockdep.c:3161 [inline]
check_prevs_add kernel/locking/lockdep.c:3280 [inline]
validate_chain kernel/locking/lockdep.c:3904 [inline]
__lock_acquire+0x250b/0x3ce0 kernel/locking/lockdep.c:5202
lock_acquire.part.0+0x11b/0x380 kernel/locking/lockdep.c:5825
down_write+0x93/0x200 kernel/locking/rwsem.c:1577
usb_deregister_dev+0x7c/0x1e0 drivers/usb/core/file.c:186
chaoskey_disconnect+0xb7/0x2a0 drivers/usb/misc/chaoskey.c:236
usb_unbind_interface+0x1e8/0x970 drivers/usb/core/driver.c:461
device_remove drivers/base/dd.c:569 [inline]
device_remove+0x122/0x170 drivers/base/dd.c:561
__device_release_driver drivers/base/dd.c:1273 [inline]
device_release_driver_internal+0x44a/0x610 drivers/base/dd.c:1296
bus_remove_device+0x22f/0x420 drivers/base/bus.c:576
device_del+0x396/0x9f0 drivers/base/core.c:3864
usb_disable_device+0x36c/0x7f0 drivers/usb/core/message.c:1418
usb_disconnect+0x2e1/0x920 drivers/usb/core/hub.c:2304
hub_port_connect drivers/usb/core/hub.c:5361 [inline]
hub_port_connect_change drivers/usb/core/hub.c:5661 [inline]
port_event drivers/usb/core/hub.c:5821 [inline]
hub_event+0x1bed/0x4f40 drivers/usb/core/hub.c:5903
process_one_work+0x9c5/0x1ba0 kernel/workqueue.c:3229
process_scheduled_works kernel/workqueue.c:3310 [inline]
worker_thread+0x6c8/0xf00 kernel/workqueue.c:3391
kthread+0x2c1/0x3a0 kernel/kthread.c:389
ret_from_fork+0x45/0x80 arch/x86/kernel/process.c:147
ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:244
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(chaoskey_list_lock);
lock(minor_rwsem);
lock(chaoskey_list_lock);
lock(minor_rwsem);
*** DEADLOCK ***
[Analysis]
The first is AA lock, it because wrong logic, it need a unlock.
The second is AB lock, it needs to rearrange the order of lock usage.
Fixes: 422dc0a4d1 ("USB: chaoskey: fail open after removal")
Reported-by: syzbot+685e14d04fe35692d3bc@syzkaller.appspotmail.com
Reported-by: syzbot+1f8ca5ee82576ec01f12@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=685e14d04fe35692d3bc
Signed-off-by: Edward Adam Davis <eadavis@qq.com>
Tested-by: syzbot+685e14d04fe35692d3bc@syzkaller.appspotmail.com
Reported-by: syzbot+5f1ce62e956b7b19610e@syzkaller.appspotmail.com
Tested-by: syzbot+5f1ce62e956b7b19610e@syzkaller.appspotmail.com
Tested-by: syzbot+1f8ca5ee82576ec01f12@syzkaller.appspotmail.com
Link: https://lore.kernel.org/r/tencent_84EB865C89862EC22EE94CB3A7C706C59206@qq.com
Cc: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 86b20af11e.
This patch leads to passing 0 to simple_read_from_buffer()
as a fifth argument, turning the read method into a nop.
The change is fundamentally flawed, as it breaks the driver.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20241007094004.242122-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I have a ASUS PN51 S mini pc that has two xhci devices. One from AMD,
and other from ASMEDIA. The one from ASMEDIA have problems when resume
from suspend, and keep broken until unplug the power cord. I use this
kernel parameter: xhci-hcd.quirks=128 and then it works ok. I make a
path to reset only the ASMEDIA xhci.
Signed-off-by: Jose Alberto Reguero <jose.alberto.reguero@gmail.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20240919184202.22249-1-jose.alberto.reguero@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce new kernel config symbol for Microchip usb5744 SMBus programming
support. Since usb5744 i2c initialization routine uses i2c SMBus APIs these
APIs should only be invoked when kernel has I2C support. This new kernel
config describes the dependency on I2C kernel support and fix the below
build issues when USB_ONBOARD_DEV=y and CONFIG_I2C=m.
riscv64-linux-ld: drivers/usb/misc/onboard_usb_dev.o:
undefined reference to `i2c_find_device_by_fwnode'
drivers/usb/misc/onboard_usb_dev.c:408:(.text+0xb24): undefined
reference to `i2c_smbus_write_block_data'
<snip>
Parsing of the i2c-bus bus handle is not put under usb5744 kernel config
check as the intention is to report an error when DT is configured for
usb5744 SMBus support and kernel has USB_ONBOARD_DEV_USB5744 disabled.
Fixes: 6782311d04 ("usb: misc: onboard_usb_dev: add Microchip usb5744 SMBus programming support")
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Suggested-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202409140539.3Axwv38m-lkp@intel.com/
Acked-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Link: https://lore.kernel.org/r/1727529992-476088-1-git-send-email-radhey.shyam.pandey@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit addresses an issue where events were being processed when
the controller was in a halted state. To fix this issue by stop
processing the events as the event count was considered stale or
invalid when the controller was halted.
Fixes: fc8bb91bc8 ("usb: dwc3: implement runtime PM")
Cc: stable@kernel.org
Signed-off-by: Selvarasu Ganesan <selvarasu.g@samsung.com>
Suggested-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240916231813.206-1-selvarasu.g@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When dwc3_resume_common() returns an error, runtime pm is left in
suspended and disabled state in dwc3_resume(). Since the device
is suspended, its parent devices (like the power domain or glue
driver) could also be suspended and may have released resources
that dwc requires. Consequently, calling dwc3_suspend_common() in
this situation could result in attempts to access unclocked or
unpowered registers.
To prevent these problems, runtime PM should always be re-enabled,
even after failed resume attempts. This ensures that
dwc3_suspend_common() is skipped in such cases.
Fixes: 68c26fe581 ("usb: dwc3: set pm runtime active before resume common")
Cc: stable@vger.kernel.org
Signed-off-by: Roy Luo <royluo@google.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240913232145.3507723-1-royluo@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
JieLi tends to use SCSI via USB Mass Storage to implement their own
proprietary commands instead of implementing another USB interface.
Enumerating it as a generic mass storage device will lead to a Hardware
Error sense key get reported.
Ignore this bogus device to prevent appearing a unusable sdX device
file.
Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
Cc: stable <stable@kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20241001083407.8336-1-uwu@icenowy.me
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Registering a gadget driver is expected to complete synchronously and
immediately after calling driver_register() this function checks that
the driver has bound so as to return an error.
Set PROBE_FORCE_SYNCHRONOUS to ensure this is the case even when
asynchronous probing is set as the default.
Fixes: fc274c1e99 ("USB: gadget: Add a new bus for gadgets")
Cc: stable@vger.kernel.org
Signed-off-by: John Keeping <jkeeping@inmusicbrands.com>
Link: https://lore.kernel.org/r/20240913102325.2826261-1-jkeeping@inmusicbrands.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
chaoskey_open() takes the lock only to increase the
counter of openings. That means that the mutual exclusion
with chaoskey_disconnect() cannot prevent an increase
of the counter and chaoskey_open() returning a success.
If that race is hit, chaoskey_disconnect() will happily
free all resources associated with the device after
it has dropped the lock, as it has read the counter
as zero.
To prevent this race chaoskey_open() has to check
the presence of the device under the lock.
However, the current per device lock cannot be used,
because it is a part of the data structure to be
freed. Hence an additional global mutex is needed.
The issue is as old as the driver.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reported-by: syzbot+422188bce66e76020e55@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=422188bce66e76020e55
Fixes: 66e3e59189 ("usb: Add driver for Altus Metrum ChaosKey device (v2)")
Rule: add
Link: https://lore.kernel.org/stable/20241002132201.552578-1-oneukum%40suse.com
Link: https://lore.kernel.org/r/20241002132201.552578-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The IO yurex_write() needs to wait for in order to have a device
ready for writing again can take a long time time.
Consequently the sleep is done in an interruptible state.
Therefore others waiting for yurex_write() itself to finish should
use mutex_lock_interruptible.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Fixes: 6bc235a2e2 ("USB: add driver for Meywa-Denki & Kayac YUREX")
Rule: add
Link: https://lore.kernel.org/stable/20240924084415.300557-1-oneukum%40suse.com
Link: https://lore.kernel.org/r/20240924084415.300557-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
iowarrior_read() uses the iowarrior dev structure, but does not use any
lock on the structure. This can cause various bugs including data-races,
so it is more appropriate to use a mutex lock to safely protect the
iowarrior dev structure. When using a mutex lock, you should split the
branch to prevent blocking when the O_NONBLOCK flag is set.
In addition, it is unnecessary to check for NULL on the iowarrior dev
structure obtained by reading file->private_data. Therefore, it is
better to remove the check.
Fixes: 946b960d13 ("USB: add driver for iowarrior devices.")
Signed-off-by: Jeongjun Park <aha310510@gmail.com>
Link: https://lore.kernel.org/r/20240919103403.3986-1-aha310510@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reorganize kerneldoc parameter names to match the parameter
order in the function header.
Problems identified using Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Link: https://lore.kernel.org/r/20240930112121.95324-19-Julia.Lawall@inria.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Impove device mode ISO transfer error tolerant by reprime the corresponding
endpoint.
The recovery steps when error occurs:
- Delete the error dTD from dQH and giveback request to user.
- Do reprime if dQH is not empty.
- Do prime when new dTD is queued if dQH is empty
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20240926022906.473319-3-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, ATDTW semaphore is used to safety link new dTD to dQH. But this
code has a bug when the endpoint is already in error before polling ATDTW
or just met error during polling ATDTW. In that cases, ATDTW will never
turn to 1 and the cpu will busy loop there.
When the endpoint met error, ENDPTSTAT will be cleared by HW. Therefore,
ENDPTSTAT should also be considered during this process. In case of
endpoint error, the current dTD should not be pushed to the head of dQH
since some dTDs may be still not executed. Therefore, the link logic is
also improved accordingly.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20240926022906.473319-2-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per USBSTS register description about UEI:
When completion of a USB transaction results in an error condition, this
bit is set by the Host/Device Controller. This bit is set along with the
USBINT bit, if the TD on which the error interrupt occurred also had its
interrupt on complete (IOC) bit set.
UI is set only when IOC set. Add checking UEI to fix miss call
isr_tr_complete_handler() when IOC have not set and transfer error happen.
Acked-by: Peter Chen <peter.chen@kernel.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20240926022906.473319-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The chipidea controller doesn't fully support sglist, such as it can not
transfer data spanned more dTDs to form a bus packet, so it can only work
on very limited cases.
The limitations as below:
1. the end address of the first sg buffer must be 4KB aligned.
2. the start and end address of the middle sg buffer must be 4KB aligned.
3. the start address of the first sg buffer must be 4KB aligned.
However, not all the use cases violate these limitations. To make the
controller compatible with most of the cases, this will try to bounce the
problem sglist entries which can be found by sglist_get_invalid_entry().
Then a bounced line buffer (the size will roundup to page size) will be
allocated to replace the remaining problem sg entries. The data will be
copied between problem sg entries and bounce buffer according to the
transfer direction. The bounce buffer will be freed when the request
completed.
Acked-by: Peter Chen <peter.chen@kernel.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20240923081203.2851768-3-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To let the device controller work properly on short packet limitations,
one usb request should only correspond to one dTD. Then every dTD will
set IOC. In theory, each dTD support up to 20KB data transfer if the
offset is 0. Due to we cannot predetermine the offset, this will limit
the usb request length to max 16KB. This should be fine since most of
the user transfer data based on this size policy.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20240923081203.2851768-2-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the imx deivice controller has below limitations:
1. can't generate short packet interrupt if IOC not set in dTD. So if one
request span more than one dTDs and only the last dTD set IOC, the usb
request will pending there if no more data comes.
2. the controller can't accurately deliver data to differtent usb requests
in some cases due to short packet. For example: one usb request span 3
dTDs, then if the controller received a short packet the next packet
will go to 2nd dTD of current request rather than the first dTD of next
request.
3. can't build a bus packet use multiple dTDs. For example: controller
needs to send one packet of 512 bytes use dTD1 (200 bytes) + dTD2
(312 bytes), actually the host side will see 200 bytes short packet.
Based on these limits, add CI_HDRC_HAS_SHORT_PKT_LIMIT flag and use it on
imx platforms.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20240923081203.2851768-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit 0edb555a65 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/usb to use .remove(), with
the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20240924084329.53094-2-u.kleine-koenig@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These drivers don't use the driver_data member of struct i2c_device_id,
so don't explicitly initialize this member.
This prepares putting driver_data in an anonymous union which requires
either no initialization or named designators. But it's also a nice
cleanup on its own.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20240920153430.503212-17-u.kleine-koenig@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function strcpy() is depreciated and potentially unsafe. It performs
no bounds checking on the destination buffer. This could result in
linear overflows beyond the end of the buffer, leading to all kinds of
misbehaviors. The safe replacement is strscpy() [1].
this fixes checkpatch warning:
WARNING: Prefer strscpy over strcpy
Link: https://www.kernel.org/doc/html/latest/process/deprecated.html#strcpy [1]
Signed-off-by: Abdul Rahim <abdul.rahim@myyahoo.com>
Reviewed-by: Kees Cook <kees@kernel.org>
Link: https://lore.kernel.org/r/20240914231756.503521-1-abdul.rahim@myyahoo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Get matching data in one step by switching to use i2c_get_match_data().
As a positive side effect the matching data is qualified as a constant.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240926122944.1251923-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the scoped variant of `device_for_each_child_node()` to
automatically handle early exits.
This prevents memory leaks if new error paths are introduced,
as no explicit refcount decrement via `fwnode_handle_put()` is needed.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240925-ucsi_glink-scoped-v2-1-a661585fff35@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed some confusing typos that were currently identified with codespell,
the details are as follows:
-in the code comments:
drivers/usb/dwc3/core.c:1406: feild ==> field
drivers/usb/dwc3/core.h:84: boundries ==> boundaries
drivers/usb/dwc3/ep0.c:148: issueing ==> issuing
drivers/usb/dwc3/host.c:38: temperary ==> temporarily
Also fixed a syntax problem in the comments.
Signed-off-by: Shen Lichuan <shenlichuan@vivo.com>
Link: https://lore.kernel.org/r/20240930022526.7255-1-shenlichuan@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
no_llseek had been defined to NULL two years ago, in commit 868941b144
("fs: remove no_llseek")
To quote that commit,
At -rc1 we'll need do a mechanical removal of no_llseek -
git grep -l -w no_llseek | grep -v porting.rst | while read i; do
sed -i '/\<no_llseek\>/d' $i
done
would do it.
Unfortunately, that hadn't been done. Linus, could you do that now, so
that we could finally put that thing to rest? All instances are of the
form
.llseek = no_llseek,
so it's obviously safe.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here is the "big" set of tty/serial driver updates for 6.12-rc1.
Nothing major in here, just nice forward progress in the slow cleanup of
the serial apis, and lots of other driver updates and fixes.
Included in here are:
- serial api updates from Jiri to make things more uniform and sane
- 8250_platform driver cleanups
- samsung serial driver fixes and updates
- qcom-geni serial driver fixes from Johan for the bizarre UART engine
that that chip seems to have. Hopefully it's in a better state now,
but hardware designers still seem to come up with more ways to make
broken UARTS 40+ years after this all should have finished.
- sc16is7xx driver updates
- omap 8250 driver updates
- 8250_bcm2835aux driver updates
- a few new serial driver bindings added
- other serial minor driver updates
All of these have been in linux-next for a long time with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZvUz1w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymAhwCcCw/6BX3aKGTyx7ZxeMRc/mjbSLIAoMUv6bGT
6H04ZvcSd63ZotAWeZsn
=PWB8
-----END PGP SIGNATURE-----
Merge tag 'tty-6.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver updates from Greg KH:
"Here is the "big" set of tty/serial driver updates for 6.12-rc1.
Nothing major in here, just nice forward progress in the slow cleanup
of the serial apis, and lots of other driver updates and fixes.
Included in here are:
- serial api updates from Jiri to make things more uniform and sane
- 8250_platform driver cleanups
- samsung serial driver fixes and updates
- qcom-geni serial driver fixes from Johan for the bizarre UART
engine that that chip seems to have. Hopefully it's in a better
state now, but hardware designers still seem to come up with more
ways to make broken UARTS 40+ years after this all should have
finished.
- sc16is7xx driver updates
- omap 8250 driver updates
- 8250_bcm2835aux driver updates
- a few new serial driver bindings added
- other serial minor driver updates
All of these have been in linux-next for a long time with no reported
problems"
* tag 'tty-6.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (65 commits)
tty: serial: samsung: Fix serial rx on Apple A7-A9
tty: serial: samsung: Fix A7-A11 serial earlycon SError
tty: serial: samsung: Use bit manipulation macros for APPLE_S5L_*
tty: rp2: Fix reset with non forgiving PCIe host bridges
serial: 8250_aspeed_vuart: Enable module autoloading
serial: qcom-geni: fix polled console corruption
serial: qcom-geni: disable interrupts during console writes
serial: qcom-geni: fix console corruption
serial: qcom-geni: introduce qcom_geni_serial_poll_bitfield()
serial: qcom-geni: fix arg types for qcom_geni_serial_poll_bit()
soc: qcom: geni-se: add GP_LENGTH/IRQ_EN_SET/IRQ_EN_CLEAR registers
serial: qcom-geni: fix false console tx restart
serial: qcom-geni: fix fifo polling timeout
tty: hvc: convert comma to semicolon
mxser: convert comma to semicolon
serial: 8250_bcm2835aux: Fix clock imbalance in PM resume
serial: sc16is7xx: convert bitmask definitions to use BIT() macro
serial: sc16is7xx: fix copy-paste errors in EFR_SWFLOWx_BIT constants
serial: sc16is7xx: remove SC16IS7XX_MSR_DELTA_MASK
serial: xilinx_uartps: Make cdns_rs485_supported static
...
Here is the large set of USB and Thunderbolt changes for 6.12-rc1.
Nothing "major" in here, except for a new 9p network gadget that has
been worked on for a long time (all of the needed acks are here.) Other
than that, it's the usual set of:
- Thunderbolt / USB4 driver updates and additions for new hardware
- dwc3 driver updates and new features added
- xhci driver updates
- typec driver updates
- USB gadget updates and api additions to make some gadgets more
configurable by userspace
- dwc2 driver updates
- usb phy driver updates
- usbip feature additions
- other minor USB driver updates
All of these have been in linux-next for a long time with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZvU0/g8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykGcACfSqouxRg8FRtq+nIKHWXI9lOTnVcAoKd9PAgq
1i7yCNopPEPEW8sjz1GX
=mY+S
-----END PGP SIGNATURE-----
Merge tag 'usb-6.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/Thunderbolt updates from Greg KH:
"Here is the large set of USB and Thunderbolt changes for 6.12-rc1.
Nothing "major" in here, except for a new 9p network gadget that has
been worked on for a long time (all of the needed acks are here)
Other than that, it's the usual set of:
- Thunderbolt / USB4 driver updates and additions for new hardware
- dwc3 driver updates and new features added
- xhci driver updates
- typec driver updates
- USB gadget updates and api additions to make some gadgets more
configurable by userspace
- dwc2 driver updates
- usb phy driver updates
- usbip feature additions
- other minor USB driver updates
All of these have been in linux-next for a long time with no reported
issues"
* tag 'usb-6.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (145 commits)
sub: cdns3: Use predefined PCI vendor ID constant
sub: cdns2: Use predefined PCI vendor ID constant
USB: misc: yurex: fix race between read and write
USB: misc: cypress_cy7c63: check for short transfer
USB: appledisplay: close race between probe and completion handler
USB: class: CDC-ACM: fix race between get_serial and set_serial
usb: r8a66597-hcd: make read-only const arrays static
usb: typec: ucsi: Fix busy loop on ASUS VivoBooks
usb: dwc3: rtk: Clean up error code in __get_dwc3_maximum_speed()
usb: storage: ene_ub6250: Fix right shift warnings
usb: roles: Improve the fix for a false positive recursive locking complaint
locking/mutex: Introduce mutex_init_with_key()
locking/mutex: Define mutex_init() once
net/9p/usbg: fix CONFIG_USB_GADGET dependency
usb: xhci: fix loss of data on Cadence xHC
usb: xHCI: add XHCI_RESET_ON_RESUME quirk for Phytium xHCI host
usb: dwc3: imx8mp: disable SS_CON and U3 wakeup for system sleep
usb: dwc3: imx8mp: add 2 software managed quirk properties for host mode
usb: host: xhci-plat: Parse xhci-missing_cas_quirk and apply quirk
usb: misc: onboard_usb_dev: add Microchip usb5744 SMBus programming support
...
Highlights:
- asus-wmi: Add support for vivobook fan profiles
- dell-laptop: Add knobs to change battery charge settings
- lg-laptop: Add operation region support
- intel-uncore-freq: Add support for efficiency latency control
- intel/ifs: Add SBAF test support
- intel/pmc: Ignore all LTRs during suspend
- platform/surface: Support for arm64 based Surface devices
- wmi: Pass event data directly to legacy notify handlers
- x86/platform/geode: switch GPIO buttons and LEDs to software properties
- bunch of small cleanups, fixes, hw-id additions, etc.
The following is an automated git shortlog grouped by driver:
Documentation:
- admin-guide: pm: Add efficiency vs. latency tradeoff to uncore documentation
ISST:
- Simplify isst_misc_reg() and isst_misc_unreg()
MAINTAINERS:
- adjust file entry in INTEL MID PLATFORM
- Add Intel MID section
Merge tag 'hwmon-for-v6.11-rc7' into review-hans:
- Merge tag 'hwmon-for-v6.11-rc7' into review-hans
Merge tag 'platform-drivers-x86-v6.11-3' into review-hans:
- Merge tag 'platform-drivers-x86-v6.11-3' into review-hans
acer-wmi:
- Use backlight power constants
asus-laptop:
- Use backlight power constants
asus-nb-wmi:
- Use backlight power constants
asus-wmi:
- don't fail if platform_profile already registered
- add debug print in more key places
- Use backlight power constants
- add support for vivobook fan profiles
dell-laptop:
- remove duplicate code w/ battery function
- Add knobs to change battery charge settings
dt-bindings:
- platform: Add Surface System Aggregator Module
- serial: Allow embedded-controller as child node
eeepc-laptop:
- Use backlight power constants
eeepc-wmi:
- Use backlight power constants
fujitsu-laptop:
- Use backlight power constants
hid-asus:
- use hid for brightness control on keyboard
ideapad-laptop:
- Make the scope_guard() clear of its scope
- move ACPI helpers from header to source file
- Use backlight power constants
int3472:
- Use str_high_low()
- Use GPIO_LOOKUP() macro
- make common part a separate module
intel-hid:
- Use string_choices API instead of ternary operator
intel/pmc:
- Ignore all LTRs during suspend
- Remove unused param idx from pmc_for_each_mode()
intel_scu_ipc:
- Move intel_scu_ipc.h out of arch/x86/include/asm
intel_scu_wdt:
- Move intel_scu_wdt.h to x86 subfolder
lenovo-ymc:
- Ignore the 0x0 state
lg-laptop:
- Add operation region support
oaktrail:
- Use backlight power constants
panasonic-laptop:
- Add support for programmable buttons
platform/mellanox:
- mlxbf-pmc: fix lockdep warning
platform/olpc:
- Remove redundant null pointer checks in olpc_ec_setup_debugfs()
platform/surface:
- Add OF support
platform/x86/amd:
- pmf: Add quirk for TUF Gaming A14
platform/x86/amd/pmf:
- Update SMU metrics table for 1AH family series
- Relocate CPU ID macros to the PMF header
- Add support for notifying Smart PC Solution updates
platform/x86/intel-uncore-freq:
- Add efficiency latency control to sysfs interface
- Add support for efficiency latency control
- Do not present separate package-die domain
platform/x86/intel/ifs:
- Fix SBAF title underline length
- Add SBAF test support
- Add SBAF test image loading support
- Refactor MSR usage in IFS test code
platform/x86/intel/pmc:
- Show live substate requirements
platform/x86/intel/pmt:
- Use PMT callbacks
platform/x86/intel/vsec:
- Add PMT read callbacks
platform/x86/intel/vsec.h:
- Move to include/linux
samsung-laptop:
- Use backlight power constants
serial-multi-instantiate:
- Don't require both I2C and SPI
thinkpad_acpi:
- Fix uninitialized symbol 's' warning
- Add Thinkpad Edge E531 fan support
touchscreen_dmi:
- add nanote-next quirk
trace:
- platform/x86/intel/ifs: Add SBAF trace support
wmi:
- Call both legacy and WMI driver notify handlers
- Merge get_event_data() with wmi_get_notify_data()
- Remove wmi_get_event_data()
- Pass event data directly to legacy notify handlers
x86-android-tablets:
- Adjust Xiaomi Pad 2 bottom bezel touch buttons LED
- Fix spelling in the comments
x86/platform/geode:
- switch GPIO buttons and LEDs to software properties
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEEuvA7XScYQRpenhd+kuxHeUQDJ9wFAmbq2tYUHGhkZWdvZWRl
QHJlZGhhdC5jb20ACgkQkuxHeUQDJ9xKYAgAoXZt1MjBDA1mP813i4bj8CYQHWO+
YnugVhEccucxgC6sBGzQeRLBNuG/VaBN6tyJ1pKYMpWV5gSthq1Iop+DZbno2ciM
QAnSSzioHB/dhYBXuKmZatkMsKLjLjtfcexUed9DfwKapqFl3XQMb6cEYasM37hH
197K4yAFF3oqQImlACwQDxN1q3eCG6bdIbEAByZW7yH644IC5zH8/CiFjTCwUx/F
aFIHQlLLzt1kjhD8AbRHhRcsGbzG2ejHsC3yrQddEJSOkInDO8baR0aDyhBTUFPE
lztuekFfaJ1Xcyoc/Zf4pi3ab1Djt+Htck3CHLO/xcl0YYMlM5vcs1QlhQ==
=sAk7
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v6.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform drivers updates from Hans de Goede:
- asus-wmi: Add support for vivobook fan profiles
- dell-laptop: Add knobs to change battery charge settings
- lg-laptop: Add operation region support
- intel-uncore-freq: Add support for efficiency latency control
- intel/ifs: Add SBAF test support
- intel/pmc: Ignore all LTRs during suspend
- platform/surface: Support for arm64 based Surface devices
- wmi: Pass event data directly to legacy notify handlers
- x86/platform/geode: switch GPIO buttons and LEDs to software
properties
- bunch of small cleanups, fixes, hw-id additions, etc.
* tag 'platform-drivers-x86-v6.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86: (65 commits)
MAINTAINERS: adjust file entry in INTEL MID PLATFORM
platform/x86: x86-android-tablets: Adjust Xiaomi Pad 2 bottom bezel touch buttons LED
platform/mellanox: mlxbf-pmc: fix lockdep warning
platform/x86/amd: pmf: Add quirk for TUF Gaming A14
platform/x86: touchscreen_dmi: add nanote-next quirk
platform/x86: asus-wmi: don't fail if platform_profile already registered
platform/x86: asus-wmi: add debug print in more key places
platform/x86: intel_scu_wdt: Move intel_scu_wdt.h to x86 subfolder
platform/x86: intel_scu_ipc: Move intel_scu_ipc.h out of arch/x86/include/asm
MAINTAINERS: Add Intel MID section
platform/x86: panasonic-laptop: Add support for programmable buttons
platform/olpc: Remove redundant null pointer checks in olpc_ec_setup_debugfs()
platform/x86: intel/pmc: Ignore all LTRs during suspend
platform/x86: wmi: Call both legacy and WMI driver notify handlers
platform/x86: wmi: Merge get_event_data() with wmi_get_notify_data()
platform/x86: wmi: Remove wmi_get_event_data()
platform/x86: wmi: Pass event data directly to legacy notify handlers
platform/x86: thinkpad_acpi: Fix uninitialized symbol 's' warning
platform/x86: x86-android-tablets: Fix spelling in the comments
platform/x86: ideapad-laptop: Make the scope_guard() clear of its scope
...
* power-supply core
- introduce power_supply_show_enum_with_available() helper
- change usb_types from an array into a bitmask
- fix early usage of power_supply_property_is_writeable() resulting
in sysfs files not being writable
- fix missing temp1_max_alarm attribute in power-supply's hwmon devices
* drivers
- max1720x: expose nvmem device
- brcmstb: cleanup driver to use latest APIs
- max77693: expose input and charging current limit
- max17042_battery: fix state of charge reading for devices without
current sensing
- axp20x_battery: add AXP717 support
- axp20x_battery: fix min/max voltage properties
- axp20x_usb_power: add AXP717 support
- axp20x_usb_power: add DT based input current limit
* Documentation updates
* misc. minor cleanups and fixes
-----BEGIN PGP SIGNATURE-----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=UKRL
-----END PGP SIGNATURE-----
Merge tag 'for-v6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
"Power-supply core:
- introduce power_supply_show_enum_with_available() helper
- change usb_types from an array into a bitmask
- fix early usage of power_supply_property_is_writeable() resulting
in sysfs files not being writable
- fix missing temp1_max_alarm attribute in power-supply's hwmon
devices
Drivers:
- max1720x: expose nvmem device
- brcmstb: cleanup driver to use latest APIs
- max77693: expose input and charging current limit
- max17042_battery: fix state of charge reading for devices without
current sensing
- axp20x_battery: add AXP717 support
- axp20x_battery: fix min/max voltage properties
- axp20x_usb_power: add AXP717 support
- axp20x_usb_power: add DT based input current limit
Documentation updates
Misc minor cleanups and fixes"
* tag 'for-v6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (38 commits)
power: supply: hwmon: Fix missing temp1_max_alarm attribute
power: supply: Drop use_cnt check from power_supply_property_is_writeable()
power: supply: ab8500: Constify struct kobj_type
power: supply: max1720x: fix a double free on error in probe()
power: supply: axp20x_battery: add support for AXP717
power: supply: axp20x_usb_power: Add support for AXP717
dt-bindings: power: supply: axp20x: Add AXP717 compatible
dt-bindings: power: supply: axp20x: Add AXP717 compatible
power: supply: axp20x_usb_power: Fix spelling mistake "reqested" -> "requested"
power: supply: Change usb_types from an array into a bitmask
power: supply: sysfs: Move power_supply_show_enum_with_available() up
power: supply: sysfs: Add power_supply_show_enum_with_available() helper
power: supply: rt9467-charger: Remove "usb_type" property write support
power: supply: ucs1002: Adjust ucs1002_set_usb_type() to accept string values
power: supply: "usb_type" property may be written to
power: supply: max1720x: add read support for nvmem
mfd: axp20x: Add ADC, BAT, and USB cells for AXP717
power: supply: core: constify psy_tzd_ops
power: reset: brcmstb: Do not go into infinite loop if reset fails
power: reset: brcmstb: Use devm_register_sys_off_handler()
...
The PCI vendor ID for Cadence is defined in pci_ids.h. Use it.
While at it, move to PCI_DEVICE() macro and usual pattern for
PCI class and device IDs.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240913131710.3630560-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PCI vendor ID for Cadence is defined in pci_ids.h. Use it.
While at it, move to PCI_DEVICE() macro and usual pattern for
PCI class and device IDs.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240913132125.3630860-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a small window during probing when IO is running
but the backlight is not registered. Processing events
during that time will crash. The completion handler
needs to check for a backlight before scheduling work.
The bug is as old as the driver.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
CC: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240912123317.1026049-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TIOCGSERIAL is an ioctl. Thus it must be atomic. It returns
two values. Racing with set_serial it can return an inconsistent
result. The mutex must be taken.
In terms of logic the bug is as old as the driver. In terms of
code it goes back to the conversion to the get_serial and
set_serial methods.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@kernel.org>
Fixes: 99f75a1fcd ("cdc-acm: switch to ->[sg]et_serial()")
Link: https://lore.kernel.org/r/20240912141916.1044393-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't populate the read-only const arrays fifoaddr, fifosel and fifoctr
on the stack at run time, instead make them static.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20240912132345.589397-1-colin.i.king@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the busy indicator is set, all other fields in CCI should be
clear according to the spec. However, some UCSI implementations do
not follow this rule and report bogus data in CCI along with the
busy indicator. Ignore the contents of CCI if the busy indicator is
set.
If a command timeout is hit it is possible that the EVENT_PENDING
bit is cleared while connector work is still scheduled which can
cause the EVENT_PENDING bit to go out of sync with scheduled connector
work. Check and set the EVENT_PENDING bit on entry to
ucsi_handle_connector_change() to fix this.
Finally, check UCSI_CCI_BUSY before the return code of ->sync_control.
This ensures that the command is cancelled even if ->sync_control
returns an error (most likely -ETIMEDOUT).
Reported-by: Anurag Bijea <icaliberdev@gmail.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219108
Bisected-by: Christian Heusel <christian@heusel.eu>
Tested-by: Anurag Bijea <icaliberdev@gmail.com>
Fixes: de52aca4d9 ("usb: typec: ucsi: Never send a lone connector change ack")
Cc: stable@vger.kernel.org
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240912074132.722855-1-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The __get_dwc3_maximum_speed() function returns an enum type which, in
this context here, is basically unsigned int. On error cases, it's
supposed to return USB_SPEED_UNKNOWN, but it was accidentally changed to
return negative error codes in commit f93e96c544 ("usb: dwc3: rtk: use
scoped device node handling to simplify error paths").
There is only one caller and because of the way that the types work out,
returning negative error codes is not a problem. They will be treated
as greater than USB_SPEED_HIGH and ignored as invalid. So this patch
does not affect run time behavior, it's just a clean up.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/865e56dc-37cc-47b1-8d35-9047ecb1984a@stanley.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Change bl_len from u16 to u32 to accommodate the necessary bit shifts.
Fix the following smatch warnings:
drivers/usb/storage/ene_ub6250.c:1509 ms_scsi_read_capacity() warn:
right shifting more than type allows 16 vs 24
drivers/usb/storage/ene_ub6250.c:1510 ms_scsi_read_capacity() warn:
right shifting more than type allows 16 vs 16
Signed-off-by: Abhishek Tamboli <abhishektamboli9@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20240912145247.15544-1-abhishektamboli9@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Improve commit fc88bb1161 ("usb: roles: add lockdep class key to struct
usb_role_switch") as follows:
* Move the lock class key declaration just above the mutex declaration such
that the declaration order of these objects matches their initialization
order.
* Destroy the mutex and lock class key just before these objects are
freed. This makes it easier to verify that the destruction calls happen
after the last use of these objects.
* Instead of switching the mutex key to the dynamic lock class key after
initialization of the mutex has completed, initialize the mutex with the
dynamic lock class key.
Cc: Amit Sunil Dhamne <amitsd@google.com>
Cc: Badhri Jagan Sridharan <badhri@google.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20240912223956.3554086-4-bvanassche@acm.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Streams should flush their TRB cache, re-read TRBs, and start executing
TRBs from the beginning of the new dequeue pointer after a 'Set TR Dequeue
Pointer' command.
Cadence controllers may fail to start from the beginning of the dequeue
TRB as it doesn't clear the Opaque 'RsvdO' field of the stream context
during 'Set TR Dequeue' command. This stream context area is where xHC
stores information about the last partially executed TD when a stream
is stopped. xHC uses this information to resume the transfer where it left
mid TD, when the stream is restarted.
Patch fixes this by clearing out all RsvdO fields before initializing new
Stream transfer using a 'Set TR Dequeue Pointer' command.
Fixes: 3d82904559 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
cc: stable@vger.kernel.org
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/PH7PR07MB95386A40146E3EC64086F409DD9D2@PH7PR07MB9538.namprd07.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SS_CON and U3 wakeup need 'ref_clk' on. iMX8MP turn off it while system
sleep, So disable these wakeup source and only enable DP/DM wakeup source
for host mode.
Reviewed-by: Xu Yang <xu.yang_2@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240906-dwc-mp-v5-3-ea8ec6774e7b@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add 2 software manage quirk properties (xhci-missing-cas-quirk and
xhci-skip-phy-init-quirk) for xhci host.
dwc3 driver have PHY management to cover both device and host mode, so add
xhci-skip-phy-init-quirk to skip PHY management from HCD core.
Cold Attach Status (CAS) bit can't be set at i.MX8MP after resume from
suspend state. So set xhci-missing-cas-quirk.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240906-dwc-mp-v5-2-ea8ec6774e7b@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Parse software managed property 'xhci-skip-phy-init-quirk' and
'xhci-skip-phy-init-quirk' to apply related quirk. It allows usb glue layer
driver apply these quirk.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240906-dwc-mp-v5-1-ea8ec6774e7b@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb5744 supports SMBus Configuration and it may be configured via the
SMBus slave interface during the hub start-up configuration stage.
To program it driver uses i2c-bus phandle (added in commit '02be19e914b8
dt-bindings: usb: Add support for Microchip usb5744 hub controller') to
get i2c client device and then based on usb5744 compatible check calls
usb5744 i2c default initialization sequence.
Apart from the USB command attach, prevent the hub from suspend.
when the USB Attach with SMBus (0xAA56) command is issued to the hub,
the hub is getting enumerated and then it puts in a suspend mode.
This causes the hub to NAK any SMBus access made by the SMBus Master
during this period and not able to see the hub's slave address while
running the "i2c probe" command.
Prevent the MCU from putting the HUB in suspend mode through register
write. The BYPASS_UDC_SUSPEND bit (Bit 3) of the RuntimeFlags2
register at address 0x411D controls this aspect of the hub. The
BYPASS_UDC_SUSPEND bit in register 0x411Dh must be set to ensure that the
MCU is always enabled and ready to respond to SMBus runtime commands.
This register needs to be written before the USB attach command is issued.
The byte sequence is as follows:
Slave addr: 0x2d 00 00 05 00 01 41 1D 08
Slave addr: 0x2d 99 37 00
Slave addr: 0x2d AA 56 00
Also since usb5744 i2c initialization routine uses i2c SMBus APIs invoke
these APIs only when i2c driver is enabled in the kernel configuration.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Link: https://lore.kernel.org/r/1725732196-70975-3-git-send-email-radhey.shyam.pandey@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce dedicated field 'power_on_delay_us' in onboard platform data
and update its delay for USB5744 configuration. Hub itself requires some
delay after reset to get to state where configuration data is going to
be accepted. Without delay upcoming support for configuration via SMBUS
is reporting a failure on the first SMBus write.
i2c 2-002d: error -ENXIO: BYPASS_UDC_SUSPEND bit configuration failed
Similar delay is likely also required for default configuration but
because there is enough time (code execution) between reset and usage
of the hub any issue is not visible but it doesn't mean delay shouldn't
be reflected.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Suggested-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/1725732196-70975-2-git-send-email-radhey.shyam.pandey@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dwc2_handle_usb_suspend_intr() function disables gadget clocks in USB
peripheral mode when no other power-down mode is available (introduced by
commit 0112b7ce68 ("usb: dwc2: Update dwc2_handle_usb_suspend_intr function.")).
However, the dwc2_drd_role_sw_set() USB role update handler attempts to
read DWC2 registers if the USB role has changed while the USB is in suspend
mode (when the clocks are gated). This causes the system to hang.
Release the gadget clocks before handling the USB role update.
Fixes: 0112b7ce68 ("usb: dwc2: Update dwc2_handle_usb_suspend_intr function.")
Cc: stable@vger.kernel.org
Signed-off-by: Tomas Marek <tomas.marek@elrest.cz>
Link: https://lore.kernel.org/r/20240906055025.25057-1-tomas.marek@elrest.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix changes incorrect usb_request->status returned during disabling
endpoints. Before fix the status returned during dequeuing requests
while disabling endpoint was ECONNRESET.
Patch change it to ESHUTDOWN.
Patch fixes issue detected during testing UVC gadget.
During stopping streaming the class starts dequeuing usb requests and
controller driver returns the -ECONNRESET status. After completion
requests the class or application "uvc-gadget" try to queue this
request again. Changing this status to ESHUTDOWN cause that UVC assumes
that endpoint is disabled, or device is disconnected and stops
re-queuing usb requests.
Fixes: 3d82904559 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
cc: stable@vger.kernel.org
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/PH7PR07MB9538E8CA7A2096AAF6A3718FDD9E2@PH7PR07MB9538.namprd07.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TCPCI USB PHY - PTN5110 could be used with SOCs that only support
the edge-triggered GPIO interrupts such as TI's K3 device AM69.
Move the interrupt configuration to the firmware which would
allow to accommodate edge triggered interrupts for such SOCs.
In order to support the edge interrupts, register irq line in advance
and keep track of occurrence during port registering.
When the edge interrupts are used, it is observed that some of the
interrupts are missed when tcpci_irq() is serving the current
interrupt. Therefore, check the status register at the end of
tcpci_irq() and re-run the function if the status is not clear
i.e. pending interrupt.
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Parth Pancholi <parth.pancholi@toradex.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://lore.kernel.org/r/20240905065328.7116-1-parth105105@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The combination of dev_err() and the returned error code could be
replaced by dev_err_probe() in driver's probe function. Let's,
converting to dev_err_probe() to make code more simple.
Signed-off-by: Lin Ruifeng <linruifeng4@huawei.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/20240907081351.19879-1-linruifeng4@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's a new pl2303 device id.
This one has been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCZuEzcQAKCRALxc3C7H1l
CGeZAQDn3AvDVGqJJ4kBZC1ldLo4aOz6z5+njmoL2cZyQ3d5iwD9F0e10fd2FA6a
fxm3gt5cJEtbs+kt8V6LhIXbTqtMJA0=
=CgUW
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-6.12-rc1-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial device id for 6.12-rc1
Here's a new pl2303 device id.
This one has been in linux-next with no reported issues.
* tag 'usb-serial-6.12-rc1-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: pl2303: add device id for Macrosilicon MS3020
Here are the USB-serial updates for 6.12-rc1, including:
- fix kobil_sct initial terminal settings
- set driver owner when registering drivers
All have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCZuEywAAKCRALxc3C7H1l
CFAWAP4muwo7gSV//umprCKbXlFGnsfS7rpDuwusRNTZFjGTPAEAs/n0htTNoFo2
RKKnRcZBk7O6Do6eByIQGuEhCYZjgAw=
=iXi0
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-6.12-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for 6.12-rc1
Here are the USB-serial updates for 6.12-rc1, including:
- fix kobil_sct initial terminal settings
- set driver owner when registering drivers
All have been in linux-next with no reported issues.
* tag 'usb-serial-6.12-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: kobil_sct: restore initial terminal settings
USB: serial: drop driver owner initialization
USB: serial: set driver owner when registering drivers
This is a platform/x86 library that is mostly being used by other
drivers not directly under arch/x86 anyway (with the exception of the
Intel MID setup code) so it makes sense that it lives under the
platform_data/x86/ directory instead.
No functional changes intended.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240909124952.1152017-3-andriy.shevchenko@linux.intel.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
We need the USB fixes in here as well, and this also resolves the merge
conflict in:
drivers/usb/typec/ucsi/ucsi.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the device id for the Macrosilicon MS3020 which is a
PL2303HXN based device.
Signed-off-by: Junhao Xie <bigfoot@classfun.cn>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Allow creators of seconday interrupters to specify the interrupt
moderation interval value in nanoseconds when creating the interrupter.
If not sure what value to use then use the xhci driver default
xhci->imod_interval
Suggested-by: Wesley Cheng <quic_wcheng@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240905143300.1959279-13-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PCI xHC host should be stopped and xhci driver memory freed before putting
host to PCI D3 state during PCI remove callback.
Hosts with XHCI_SPURIOUS_WAKEUP quirk did this the wrong way around
and set the host to D3 before calling usb_hcd_pci_remove(dev), which will
access the host to stop it, and then free xhci.
Fixes: f1f6d9a8b5 ("xhci: don't dereference a xhci member after removing xhci")
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240905143300.1959279-12-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce an initial check for an empty list prior to entering the while
loop. Which enables, the implementation of distinct warnings to
differentiate between scenarios where the list is initially empty and
when it has been emptied during processing skipped isoc TDs.
These adjustments not only simplifies the large while loop, but also
facilitates future enhancements to the handle_tx_event() function.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240905143300.1959279-11-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
HCD does not allocate or request interrupt for the xhci driver, but HCD
does free and sync xhci interrupts in some cases. Add comment detailing
in which cases HCD will free/sync xhci interrupts.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240905143300.1959279-9-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variable 'sbrn' is used to store the Serial Bus Release Number, which is
then only used for a debug message. Thus, 'sbrn' can be a local variable
and assigned after the primary HCD check. The SBRN debug message is only
printed when a primary HCD is setup.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240905143300.1959279-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Completion codes 'COMP_SUCCESS' and 'COMP_SHORT_PACKET' are the most
frequently encountered completion codes. Typically, these codes do not
trigger a default debug message but rather a warning that indicates a
potential issue. This behavior is consistent across all transfer types
with the exception of Bulk transfers. To reduce unnecessary log clutter,
remove the Bulk 'COMP_SHORT_PACKET' debug message.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240905143300.1959279-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The removed debug messages trigger each time an isoc frame is handled.
In case of an error, a dedicated debug message exists.
For example, a 60fps USB camera will trigger the debug message every 0.6s.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240905143300.1959279-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure we move the requests from the read_queue to the end of the
read_pool list, avoiding looping and using the same one request all
the time.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240905143300.1959279-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't flush all pending DbC data requests when an endpoint halts.
An endpoint may halt and xHC DbC triggers a STALL error event if there's
an issue with a bulk data transfer. The transfer should restart once xHC
DbC receives a ClearFeature(ENDPOINT_HALT) request from the host.
Once xHC DbC restarts it will start from the TRB pointed to by dequeue
field in the endpoint context, which might be the same TRB we got the
STALL event for. Turn the TRB to a no-op in this case to make sure xHC
DbC doesn't reuse and tries to retransmit this same TRB after we already
handled it, and gave its corresponding data request back.
Other STALL events might be completely bogus.
Lukasz Bartosik discovered that xHC DbC might issue spurious STALL events
if hosts sends a ClearFeature(ENDPOINT_HALT) request to non-halted
endpoints even without any active bulk transfers.
Assume STALL event is spurious if it reports 0 bytes transferred, and
the endpoint stopped on the STALLED TRB.
Don't give back the data request corresponding to the TRB in this case.
The halted status is per endpoint. Track it with a per endpoint flag
instead of the driver invented DbC wide DS_STALLED state.
DbC remains in DbC-Configured state even if endpoints halt. There is no
Stalled state in the DbC Port state Machine (xhci section 7.6.6)
Reported-by: Łukasz Bartosik <ukaszb@chromium.org>
Closes: https://lore.kernel.org/linux-usb/20240725074857.623299-1-ukaszb@chromium.org/
Tested-by: Łukasz Bartosik <ukaszb@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240905143300.1959279-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bit_types array just hold a list of valid enum power_supply_usb_type
values which map to 0 - 9. This can easily be represented as a bitmap.
This reduces the size of struct power_supply_desc and further reduces
the data section size by drivers no longer needing to store the array.
This also unifies how usb_types are handled with charge_behaviours,
which allows power_supply_show_usb_type() to be removed.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20240831142039.28830-7-hdegoede@redhat.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The Cable PD Revision field in GET_CABLE_PROPERTY was
introduced in UCSI v2.1, so adding check for that.
The cable properties are also not used anywhere after the
cable is registered, so removing the cable_prop member
from struct ucsi_connector while at it.
Fixes: 38ca416597 ("usb: typec: ucsi: Register cables based on GET_CABLE_PROPERTY")
Cc: stable@vger.kernel.org
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240903130945.3395291-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Partner PD Revision field in GET_CONNECTOR_CAPABILITY
data structure was introduced in UCSI v2.1. In
ucsi_check_connector_capability() the version was assumed to
be 2.0, and in ucsi_register_partner() the field is accessed
completely unconditionally.
Fixing the version in ucsi_check_connector_capability(), and
replacing the unconditional pd_revision assignment with a
direct call to ucsi_check_connector_capability() in
ucsi_register_port(). After this the revision is also
checked only if there is a PD contract.
Fixes: b9fccfdb4e ("usb: typec: ucsi: Get PD revision for partner")
Cc: stable@vger.kernel.org
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240830111645.2134301-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fix addresses STAR 9001285599, which only affects DWC_usb3 version
3.20a. The timer value for PM_LC_TIMER in DWC_usb3 3.20a for the Link
ECN changes is incorrect. If the PM TIMER ECN is enabled via GUCTL2[19],
the link compliance test (TD7.21) may fail. If the ECN is not enabled
(GUCTL2[19] = 0), the controller will use the old timer value (5us),
which is still acceptable for the link compliance test. Therefore, clear
GUCTL2[19] to pass the USB link compliance test: TD 7.21.
Cc: stable@vger.kernel.org
Signed-off-by: Faisal Hassan <quic_faisalh@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240829094502.26502-1-quic_faisalh@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When operating in High-Speed, it is observed that DSTS[USBLNKST] doesn't
update link state immediately after receiving the wakeup interrupt. Since
wakeup event handler calls the resume callbacks, there is a chance that
function drivers can perform an ep queue, which in turn tries to perform
remote wakeup from send_gadget_ep_cmd(STARTXFER). This happens because
DSTS[[21:18] wasn't updated to U0 yet, it's observed that the latency of
DSTS can be in order of milli-seconds. Hence avoid calling gadget_wakeup
during startxfer to prevent unnecessarily issuing remote wakeup to host.
Fixes: c36d8e947a ("usb: dwc3: gadget: put link to U0 before Start Transfer")
Cc: stable@vger.kernel.org
Suggested-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240828064302.3796315-1-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We move the func_utils.h header to include/linux/usb to be
able to compile function drivers outside of the
drivers/usb/gadget/function directory.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20240116-ml-topic-u9p-v12-1-9a27de5160e0@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Describe the power management relationship between a tunneled USB3 device
and the tunnel providing USB4 host with a device link as the relationship
between them is not evident from normal device hierarchy.
Tunneling capable ports have an ACPI _DSD object pointing to the USB4
Host Interface that is used to establish USB3 3.x tunnels
Set the link directly between tunneled USB3 devices and USB4 Host
Interface to ensure that the USB4 host can runtime suspend if no tunneled
USB 3.x devices exist.
Current Thunderbolt code sets a link between USB4 Host Interface and USB3
xHCI host which prevents USB4 Host Interface from runtime suspending even
if the USB3 host is only serving native USB devices.
See commit b2be2b05cf ("thunderbolt: Create device links from ACPI
description") for details.
As the device link is only set for USB3 devices that are already tunneled
we know that USB4 Host Interface exists and is bound to its driver.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240830152630.3943215-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add 'tunnel_mode' enum to usb device structure to describe if a USB3
link is tunneled over USB4, or connected directly using native USB2/USB3
protocols.
Tunneled devices depend on USB4 NHI host to maintain the tunnel.
Knowledge about tunneled devices is important to ensure correct
suspend and resume order between USB4 hosts and tunneled devices.
i.e. make sure tunnel is up before the USB device using it resumes.
USB hosts such as xHCI may have vendor specific ways to detect tunneled
connections. This 'tunnel_mode' parameter can be set by USB3 host driver
during hcd->driver->update_device(hcd, udev) callback.
tunnel_mode can be set to:
USB_LINK_UNKNOWN = 0
USB_LINK_NATIVE
USB_LINK_TUNNELED
USB_LINK_UNKNOWN is used in case host is not capable of detecting
tunneled links.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240830152630.3943215-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Knowledge about tunneled devices is useful in order to correctly describe
the relationship between tunneled USB3 device and USB4 Host Interface,
ensuring proper suspend and resume order, and to be able to power down
Thunderbolt if there is no need for tunneling.
Intel hosts share if a USB3 connection is native or tunneled via vendor
specific "SPR eSS PORT" registers.
These vendor registers are available if host supports a vendor specific
SPR shadow extended capability with ID 206. Registers are per USB3 port
and 0x20 apart.
Knowing the tunneling status of the device connected to roothub is enough
as all its children will have the same status.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240830152630.3943215-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace kthread_create/wake_up_process() with kthread_run()
to simplify the code.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Hongbo Li <lihongbo22@huawei.com>
Link: https://lore.kernel.org/r/20240903014249.3098082-1-lihongbo22@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bInterfaceProtocol is hardcoded to USB_CDC_ACM_PROTO_AT_V25TER. This
will lead to problems with ModemManger which will gladly try to probe
that port as a modem if the gadget also has a network function.
ModemManager will try to send AT commands to the ACM port. Make the
bInterfaceProtocol configurable. For this, track the number of instances
and only allow write to the property if there are no intances (yet).
This will also set bFunctionProtocol to the same value, see commit
5c8db070b4 ("USB: Change acm_iad_descriptor bFunctionProtocol to
USB_CDC_ACM_PROTO_AT_V25TER") for more details.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Link: https://lore.kernel.org/r/20240825180446.3757073-1-mwalle@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
devm_clk_get() and clk_prepare_enable() can be replaced by helper
function devm_clk_get_enabled(). Let's use devm_clk_get_enabled() to
simplify code and avoid calling clk_disable_unprepare().
Signed-off-by: Zhang Zekun <zhangzekun11@huawei.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20240902123020.29267-3-zhangzekun11@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The issue is that before entering the crash kernel, the DWC USB controller
did not perform operations such as resetting the interrupt mask bits.
After entering the crash kernel,before the USB interrupt handler
registration was completed while loading the DWC USB driver,an GINTSTS_SOF
interrupt was received.This triggered the misroute_irq process within the
GIC handling framework,ultimately leading to the misrouting of the
interrupt,causing it to be handled by the wrong interrupt handler
and resulting in the issue.
Summary:In a scenario where the kernel triggers a panic and enters
the crash kernel,it is necessary to ensure that the interrupt mask
bit is not enabled before the interrupt registration is complete.
If an interrupt reaches the CPU at this moment,it will certainly
not be handled correctly,especially in cases where this interrupt
is reported frequently.
Please refer to the Crashkernel dmesg information as follows
(the message on line 3 was added before devm_request_irq is
called by the dwc2_driver_probe function):
[ 5.866837][ T1] dwc2 JMIC0010:01: supply vusb_d not found, using dummy regulator
[ 5.874588][ T1] dwc2 JMIC0010:01: supply vusb_a not found, using dummy regulator
[ 5.882335][ T1] dwc2 JMIC0010:01: before devm_request_irq irq: [71], gintmsk[0xf300080e], gintsts[0x04200009]
[ 5.892686][ C0] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.10.0-jmnd1.2_RC #18
[ 5.900327][ C0] Hardware name: CMSS HyperCard4-25G/HyperCard4-25G, BIOS 1.6.4 Jul 8 2024
[ 5.908836][ C0] Call trace:
[ 5.911965][ C0] dump_backtrace+0x0/0x1f0
[ 5.916308][ C0] show_stack+0x20/0x30
[ 5.920304][ C0] dump_stack+0xd8/0x140
[ 5.924387][ C0] pcie_xxx_handler+0x3c/0x1d8
[ 5.930121][ C0] __handle_irq_event_percpu+0x64/0x1e0
[ 5.935506][ C0] handle_irq_event+0x80/0x1d0
[ 5.940109][ C0] try_one_irq+0x138/0x174
[ 5.944365][ C0] misrouted_irq+0x134/0x140
[ 5.948795][ C0] note_interrupt+0x1d0/0x30c
[ 5.953311][ C0] handle_irq_event+0x13c/0x1d0
[ 5.958001][ C0] handle_fasteoi_irq+0xd4/0x260
[ 5.962779][ C0] __handle_domain_irq+0x88/0xf0
[ 5.967555][ C0] gic_handle_irq+0x9c/0x2f0
[ 5.971985][ C0] el1_irq+0xb8/0x140
[ 5.975807][ C0] __setup_irq+0x3dc/0x7cc
[ 5.980064][ C0] request_threaded_irq+0xf4/0x1b4
[ 5.985015][ C0] devm_request_threaded_irq+0x80/0x100
[ 5.990400][ C0] dwc2_driver_probe+0x1b8/0x6b0
[ 5.995178][ C0] platform_drv_probe+0x5c/0xb0
[ 5.999868][ C0] really_probe+0xf8/0x51c
[ 6.004125][ C0] driver_probe_device+0xfc/0x170
[ 6.008989][ C0] device_driver_attach+0xc8/0xd0
[ 6.013853][ C0] __driver_attach+0xe8/0x1b0
[ 6.018369][ C0] bus_for_each_dev+0x7c/0xdc
[ 6.022886][ C0] driver_attach+0x2c/0x3c
[ 6.027143][ C0] bus_add_driver+0xdc/0x240
[ 6.031573][ C0] driver_register+0x80/0x13c
[ 6.036090][ C0] __platform_driver_register+0x50/0x5c
[ 6.041476][ C0] dwc2_platform_driver_init+0x24/0x30
[ 6.046774][ C0] do_one_initcall+0x50/0x25c
[ 6.051291][ C0] do_initcall_level+0xe4/0xfc
[ 6.055894][ C0] do_initcalls+0x80/0xa4
[ 6.060064][ C0] kernel_init_freeable+0x198/0x240
[ 6.065102][ C0] kernel_init+0x1c/0x12c
Signed-off-by: Shawn Shao <shawn.shao@jaguarmicro.com>
Link: https://lore.kernel.org/r/20240830031709.134-1-shawn.shao@jaguarmicro.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use devm_platform_ioremap_resource() wrapper instead of two calls, which
together with returning directly instead of useless goto, allows to
nicely simplify the probe() function.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240814-b4-cleanup-h-of-node-put-usb-v1-10-95481b9682bc@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Obtain the device node reference with scoped/cleanup.h to reduce error
handling and make the code a bit simpler.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240814-b4-cleanup-h-of-node-put-usb-v1-9-95481b9682bc@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use devm_platform_ioremap_resource() wrapper instead of two calls. This
allows also dropping local 'res' variable.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240814-b4-cleanup-h-of-node-put-usb-v1-8-95481b9682bc@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Obtain the device node reference with scoped/cleanup.h to reduce error
handling and make the code a bit simpler.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240814-b4-cleanup-h-of-node-put-usb-v1-7-95481b9682bc@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Obtain the device node reference with scoped/cleanup.h to reduce error
handling and make the code a bit simpler. Scoped/cleanup.h coding style
expects variable declaration with initialization, so the
of_get_compatible_child() call has to be moved earlier, before any goto
jumps happen.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240814-b4-cleanup-h-of-node-put-usb-v1-6-95481b9682bc@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use dev_err_probe() to make the error paths a bit simpler.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240814-b4-cleanup-h-of-node-put-usb-v1-5-95481b9682bc@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use devm_clk_get_enabled() to drop clock preparing and handling from
error and remove paths. This makes the code a bit simpler.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240814-b4-cleanup-h-of-node-put-usb-v1-4-95481b9682bc@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use dev_err_probe() to make the error paths a bit simpler.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240814-b4-cleanup-h-of-node-put-usb-v1-2-95481b9682bc@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Obtain the device node reference with scoped/cleanup.h to reduce error
handling and make the code a bit simpler. Scoped/cleanup.h coding style
expects variable declaration with initialization, so the
of_get_compatible_child() call has to be moved earlier, before any goto
jumps happen.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://lore.kernel.org/r/20240814-b4-cleanup-h-of-node-put-usb-v1-1-95481b9682bc@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'struct usb_device_id' and 'struct us_unusual_dev' are not modified in
these drivers.
Constifying these structures moves some data to a read-only section, so
increase overall security, especially when the structure holds some
function pointers (which is the case for struct us_unusual_dev).
On a x86_64, with allmodconfig, as an example:
Before:
======
text data bss dec hex filename
25249 4261 896 30406 76c6 drivers/usb/storage/alauda.o
3969 672 360 5001 1389 drivers/usb/storage/cypress_atacb.o
After:
=====
text data bss dec hex filename
25461 4041 896 30398 76be drivers/usb/storage/alauda.o
4225 400 360 4985 1379 drivers/usb/storage/cypress_atacb.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/b1b75a2a64b1f6cfad2a611f71393f281178fd3f.1724507157.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, suspend interrupt is enabled before pullup enable operation.
This will cause a suspend interrupt assert right after pullup DP. This
suspend interrupt is meaningless, so this will ignore such interrupt
by enable it after usb reset completed.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20240823073832.1702135-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some small USB fixes for 6.11-rc6. Included in here are:
- dwc3 driver fixes for reported issues
- MAINTAINER file update, marking a driver as unsupported :(
- cdnsp driver fixes
- USB gadget driver fix
- USB sysfs fix
- other tiny fixes
- new device ids for usb serial driver
All of these have been in linux-next this week with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZtNVTw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymqWwCgmITg5Owdigw+ejnkLJ4Q/CHYfRkAoLh7nkcm
kaX7IqZLgVDr4rvgVcmR
=azoE
-----END PGP SIGNATURE-----
Merge tag 'usb-6.11-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB fixes for 6.11-rc6. Included in here are:
- dwc3 driver fixes for reported issues
- MAINTAINER file update, marking a driver as unsupported :(
- cdnsp driver fixes
- USB gadget driver fix
- USB sysfs fix
- other tiny fixes
- new device ids for usb serial driver
All of these have been in linux-next this week with no reported
issues"
* tag 'usb-6.11-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: serial: option: add MeiG Smart SRM825L
usb: cdnsp: fix for Link TRB with TC
usb: dwc3: st: add missing depopulate in probe error path
usb: dwc3: st: fix probed platform device ref count on probe error path
usb: dwc3: ep0: Don't reset resource alloc flag (including ep0)
usb: core: sysfs: Unmerge @usb3_hardware_lpm_attr_group in remove_power_attributes()
usb: typec: fsa4480: Relax CHIP_ID check
usb: dwc3: xilinx: add missing depopulate in probe error path
usb: dwc3: omap: add missing depopulate in probe error path
dt-bindings: usb: microchip,usb2514: Fix reference USB device schema
usb: gadget: uvc: queue pump work in uvcg_video_enable()
cdc-acm: Add DISABLE_ECHO quirk for GE HealthCare UI Controller
usb: cdnsp: fix incorrect index in cdnsp_get_hw_deq function
usb: dwc3: core: Prevent USB core invalid event buffer address access
MAINTAINERS: Mark UVC gadget driver as orphan
Here's a new modem device id.
This one has been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCZtHD4wAKCRALxc3C7H1l
CAQVAP4vhB9K9/j24wsz+B7N1WHSZe/USLUsO5xJGwLOu3npXwEAtd8Xzz/DVFaw
/qmtd4YflELooK6u0sK1vla/jydnzgU=
=wBM6
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-6.11-rc6' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial device id for 6.11-rc6
Here's a new modem device id.
This one has been in linux-next with no reported issues.
* tag 'usb-serial-6.11-rc6' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add MeiG Smart SRM825L
This corrects the tzmem virt-to-phys conversion, which caused issues for
the uefisecapp implementation of EFI variable access. SDM670 is excluded
from tzmem usage due to reported issues.
The SCM get wait queue context call is corrected to be marked ATOMIC and
some dead code in qseecom, following the tzmem conversion, is removed.
The memory backing command DB is remapped writecombined, to avoid XPU
violations when Linux runs without the Qualcomm hypervisor.
Two compile fixes are added for pd-mapper, and the broken reference
count is corrected, to make pd-mapper deal with remoteprocs going away.
In pmic_glink a race condition where the client callbacks might be
called before we returned the client handle is corrected. The broken conditions
for when to signal that the firmware is going down is also corrected.
In the pmic_glink UCSI driver, the ucsi_unregister() is moved out of the
pdr callback, as this is being invoked in atomic context.
Konrad's email address is updated in MAINTAINERS, and related mailmap
entries are added.
-----BEGIN PGP SIGNATURE-----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=Zo90
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=pkFq
-----END PGP SIGNATURE-----
Merge tag 'qcom-drivers-fixes-for-6.11' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/fixes
Qualcomm driver fixes for v6.11
This corrects the tzmem virt-to-phys conversion, which caused issues for
the uefisecapp implementation of EFI variable access. SDM670 is excluded
from tzmem usage due to reported issues.
The SCM get wait queue context call is corrected to be marked ATOMIC and
some dead code in qseecom, following the tzmem conversion, is removed.
The memory backing command DB is remapped writecombined, to avoid XPU
violations when Linux runs without the Qualcomm hypervisor.
Two compile fixes are added for pd-mapper, and the broken reference
count is corrected, to make pd-mapper deal with remoteprocs going away.
In pmic_glink a race condition where the client callbacks might be
called before we returned the client handle is corrected. The broken conditions
for when to signal that the firmware is going down is also corrected.
In the pmic_glink UCSI driver, the ucsi_unregister() is moved out of the
pdr callback, as this is being invoked in atomic context.
Konrad's email address is updated in MAINTAINERS, and related mailmap
entries are added.
* tag 'qcom-drivers-fixes-for-6.11' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
soc: qcom: pd-mapper: Fix singleton refcount
firmware: qcom: tzmem: disable sdm670 platform
soc: qcom: pmic_glink: Actually communicate when remote goes down
usb: typec: ucsi: Move unregister out of atomic section
soc: qcom: pmic_glink: Fix race during initialization
firmware: qcom: qseecom: remove unused functions
firmware: qcom: tzmem: fix virtual-to-physical address conversion
firmware: qcom: scm: Mark get_wq_ctx() as atomic call
MAINTAINERS: Update Konrad Dybcio's email address
mailmap: Add an entry for Konrad Dybcio
soc: qcom: pd-mapper: mark qcom_pdm_domains as __maybe_unused
soc: qcom: cmd-db: Map shared memory as WC, not WB
soc: qcom: pd-mapper: Depend on ARCH_QCOM || COMPILE_TEST
Link: https://lore.kernel.org/r/20240826145209.1646159-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Commit 6a6c8b362b ("usb, kobil: Sort out some bogus tty handling")
intended to fix and clean up the device-specific initial terminal
settings but instead confused the termios input and local control flags
and re-enabled ICRNL and IXON.
Drop the bogus masking of l-flags from the default i-flags (which has no
effect) and restore the original device-specific i-flags.
Fixes: 6a6c8b362b ("usb, kobil: Sort out some bogus tty handling")
Signed-off-by: Johan Hovold <johan@kernel.org>
Core in usb_serial_register_drivers() already sets the .owner, so driver
does not need to.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Modules registering drivers with usb_serial_register_drivers() might
forget to set .owner field. The field is used by some of other kernel
parts for reference counting (try_module_get()), so it is expected that
drivers will set it.
Solve the problem by moving this task away from the drivers to the core
USB serial code, just like we did for platform_driver in
commit 9447057eaf ("platform_device: use a macro instead of
platform_driver_register").
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
[ johan: amend commit summary ]
Signed-off-by: Johan Hovold <johan@kernel.org>
There can be multiple role switch devices running on a platform. Given
that lockdep is not capable of differentiating between locks of
different instances, false positive warnings for circular locking are
reported. To prevent this, register unique lockdep key for each of the
individual instances.
Signed-off-by: Amit Sunil Dhamne <amitsd@google.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20240822223717.253433-1-amitsd@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add MODULE_DEVICE_TABLE(), so modules could be properly autoloaded
based on the alias from of_device_id table.
Signed-off-by: Liao Chen <liaochen4@huawei.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240822130113.164644-5-liaochen4@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add MODULE_DEVICE_TABLE(), so modules could be properly autoloaded
based on the alias from of_device_id table.
Signed-off-by: Liao Chen <liaochen4@huawei.com>
Link: https://lore.kernel.org/r/20240822130113.164644-4-liaochen4@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add MODULE_DEVICE_TABLE(), so modules could be properly autoloaded
based on the alias from of_device_id table.
Signed-off-by: Liao Chen <liaochen4@huawei.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240822130113.164644-3-liaochen4@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add MODULE_DEVICE_TABLE(), so modules could be properly autoloaded
based on the alias from of_device_id table.
Signed-off-by: Liao Chen <liaochen4@huawei.com>
Link: https://lore.kernel.org/r/20240822130113.164644-2-liaochen4@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stop Endpoint command on LINK TRB with TC bit set to 1 causes that
internal cycle bit can have incorrect state after command complete.
In consequence empty transfer ring can be incorrectly detected
when EP is resumed.
NOP TRB before LINK TRB avoid such scenario. Stop Endpoint command
is then on NOP TRB and internal cycle bit is not changed and have
correct value.
Fixes: 3d82904559 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
cc: <stable@vger.kernel.org>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/PH7PR07MB953878279F375CCCE6C6F40FDD8E2@PH7PR07MB9538.namprd07.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the GET_ERROR_STATUS command fails, ucsi_read_error() can
not reach the condition where the CCI error bit is checked,
because ucsi_run_command() has already checked that bit and
returned an error.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240816135859.3499351-7-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The command cancellation can be done right after detecting
that the PPM is busy. There is no need to do it separately
in ucsi_read_error() and ucsi_send_command_common().
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240816135859.3499351-6-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
So far that command was only used to read the response to
the Discover Identity Request, but it is handled with two
separate functions, which is not really necessary. Squashing
the command execution into a single function. That function
can now also be used to read other messages on top of the
Request Identity response.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240816135859.3499351-5-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This will make sure that the identity sysfs attribute files
are kept hidden if the UCSI interface doesn't support
reading the USB Power Delivery messages.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Link: https://lore.kernel.org/r/20240816135859.3499351-4-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
That may silently corrupt the data. Instead, failing attempts
to read more than the interface can handle.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Link: https://lore.kernel.org/r/20240816135859.3499351-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The new fields are valid only with the new UCSI versions.
They are at offsets that go beyond the MAX_DATA_LENGTH (16
bytes) with the older UCSI versions. That has not caused any
problems before because nothing uses those new fields yet.
Because they are not used yet, dropping them for now.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240816135859.3499351-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The probe function never performs any paltform device allocation, thus
error path "undo_platform_dev_alloc" is entirely bogus. It drops the
reference count from the platform device being probed. If error path is
triggered, this will lead to unbalanced device reference counts and
premature release of device resources, thus possible use-after-free when
releasing remaining devm-managed resources.
Fixes: f83fca0707 ("usb: dwc3: add ST dwc3 glue layer to manage dwc3 HC")
Cc: stable@vger.kernel.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://lore.kernel.org/r/20240814093957.37940-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DWC3_EP_RESOURCE_ALLOCATED flag ensures that the resource of an
endpoint is only assigned once. Unless the endpoint is reset, don't
clear this flag. Otherwise we may set endpoint resource again, which
prevents the driver from initiate transfer after handling a STALL or
endpoint halt to the control endpoint.
Commit f2e0eee470 ("usb: dwc3: ep0: Don't reset resource alloc flag")
was fixing the initial issue, but did this only for physical ep1. Since
the function dwc3_ep0_stall_and_restart is resetting the flags for both
physical endpoints, this also has to be done for ep0.
Cc: stable@vger.kernel.org
Fixes: b311048c17 ("usb: dwc3: gadget: Rewrite endpoint allocation flow")
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20240814-dwc3hwep0reset-v2-1-29e1d7d923ea@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Device attribute group @usb3_hardware_lpm_attr_group is merged by
add_power_attributes(), but it is not unmerged explicitly, fixed by
unmerging it in remove_power_attributes().
Fixes: 655fe4effe ("usbcore: add sysfs support to xHCI usb3 hardware LPM")
Cc: stable@vger.kernel.org
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20240820-sysfs_fix-v2-1-a9441487077e@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some FSA4480-compatible chips like the OCP96011 used on Fairphone 5
return 0x00 from the CHIP_ID register. Handle that gracefully and only
fail probe when the I2C read has failed.
With this the dev_dbg will print 0 but otherwise continue working.
[ 0.251581] fsa4480 1-0042: Found FSA4480 v0.0 (Vendor ID = 0)
Cc: stable@vger.kernel.org
Fixes: e885f5f1f2 ("usb: typec: fsa4480: Check if the chip is really there")
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20240818-fsa4480-chipid-fix-v1-1-17c239435cf7@fairphone.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit "6acba0345b68 usb:gadget:uvc Do not use worker thread to pump
isoc usb requests", pump work could only be queued in uvc_video_complete()
and uvc_v4l2_qbuf(). If VIDIOC_QBUF is executed before VIDIOC_STREAMON,
we can only depend on uvc_video_complete() to queue pump work. However,
this requires some free requests in req_ready list. If req_ready list is
empty all the time, pump work will never be queued and video datas will
never be pumped to usb controller. Actually, this situation could happen
when run uvc-gadget with static image:
$ ./uvc-gadget -i 1080p.jpg uvc.0
When capture image from this device, the user app will always block there.
The issue is uvc driver has queued video buffer before streamon, but the
req_ready list is empty all the time after streamon. This will queue pump
work in uvcg_video_enable() to fill some request to req_ready list so the
uvc device could work properly.
Fixes: 6acba0345b ("usb:gadget:uvc Do not use worker thread to pump isoc usb requests")
Cc: stable@vger.kernel.org
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20240814112537.2608949-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB_DEVICE(0x1901, 0x0006) may send data before cdc_acm is ready, which
may be misinterpreted in the default N_TTY line discipline.
Signed-off-by: Ian Ray <ian.ray@gehealthcare.com>
Acked-by: Oliver Neuku <oneukum@suse.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20240814072905.2501-1-ian.ray@gehealthcare.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While supporting GET_REPORT is a mandatory request per the HID
specification the current implementation of the GET_REPORT request responds
to the USB Host with an empty reply of the request length. However, some
USB Hosts will request the contents of feature reports via the GET_REPORT
request. In addition, some proprietary HID 'protocols' will expect
different data, for the same report ID, to be to become available in the
feature report by sending a preceding SET_REPORT to the USB Device that
defines what data is to be presented when that feature report is
subsequently retrieved via GET_REPORT (with a very fast < 5ms turn around
between the SET_REPORT and the GET_REPORT).
There are two other patch sets already submitted for adding GET_REPORT
support. The first [1] allows for pre-priming a list of reports via IOCTLs
which then allows the USB Host to perform the request, with no further
userspace interaction possible during the GET_REPORT request. And another
[2] which allows for a single report to be setup by userspace via IOCTL,
which will be fetched and returned by the kernel for subsequent GET_REPORT
requests by the USB Host, also with no further userspace interaction
possible.
This patch, while loosely based on both the patch sets, differs by allowing
the option for userspace to respond to each GET_REPORT request by setting
up a poll to notify userspace that a new GET_REPORT request has arrived. To
support this, two extra IOCTLs are supplied. The first of which is used to
retrieve the report ID of the GET_REPORT request (in the case of having
non-zero report IDs in the HID descriptor). The second IOCTL allows for
storing report responses in a list for responding to requests.
The report responses are stored in a list (it will be either added if it
does not exist or updated if it exists already). A flag (userspace_req) can
be set to whether subsequent requests notify userspace or not.
Basic operation when a GET_REPORT request arrives from USB Host:
- If the report ID exists in the list and it is set for immediate return
(i.e. userspace_req == false) then response is sent immediately,
userspace is not notified
- The report ID does not exist, or exists but is set to notify userspace
(i.e. userspace_req == true) then notify userspace via poll:
- If userspace responds, and either adds or update the response in
the list and respond to the host with the contents
- If userspace does not respond within the fixed timeout (2500ms)
but the report has been set prevously, then send 'old' report
contents
- If userspace does not respond within the fixed timeout (2500ms)
and the report does not exist in the list then send an empty
report
Note that userspace could 'prime' the report list at any other time.
While this patch allows for flexibility in how the system responds to
requests, and therefore the HID 'protocols' that could be supported, a
drawback is the time it takes to service the requests and therefore the
maximum throughput that would be achievable. The USB HID Specification
v1.11 itself states that GET_REPORT is not intended for periodic data
polling, so this limitation is not severe.
Testing on an iMX8M Nano Ultra Lite with a heavy multi-core CPU loading
showed that userspace can typically respond to the GET_REPORT request
within 1200ms - which is well within the 5000ms most operating systems seem
to allow, and within the 2500ms set by this patch.
[1] https://lore.kernel.org/all/20220805070507.123151-2-sunil@amarulasolutions.com/
[2] https://lore.kernel.org/all/20220726005824.2817646-1-vi@endrift.com/
Signed-off-by: David Sands <david.sands@biamp.com>
Signed-off-by: Chris Wulff <chris.wulff@biamp.com>
Link: https://lore.kernel.org/r/20240817142850.1311460-2-crwulff@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In polling mode, if no IRQ was requested there is no need to free it.
Call devm_free_irq() only if client->irq is set. This fixes the warning
caused by the tps6598x module removal:
WARNING: CPU: 2 PID: 333 at kernel/irq/devres.c:144 devm_free_irq+0x80/0x8c
...
...
Call trace:
devm_free_irq+0x80/0x8c
tps6598x_remove+0x28/0x88 [tps6598x]
i2c_device_remove+0x2c/0x9c
device_remove+0x4c/0x80
device_release_driver_internal+0x1cc/0x228
driver_detach+0x50/0x98
bus_remove_driver+0x6c/0xbc
driver_unregister+0x30/0x60
i2c_del_driver+0x54/0x64
tps6598x_i2c_driver_exit+0x18/0xc3c [tps6598x]
__arm64_sys_delete_module+0x184/0x264
invoke_syscall+0x48/0x110
el0_svc_common.constprop.0+0xc8/0xe8
do_el0_svc+0x20/0x2c
el0_svc+0x28/0x98
el0t_64_sync_handler+0x13c/0x158
el0t_64_sync+0x190/0x194
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240816124150.608125-1-w.egorov@phytec.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix potential dereferencing of ERR_PTR() in find_format_by_pix()
and uvc_v4l2_enum_format().
Fix the following smatch errors:
drivers/usb/gadget/function/uvc_v4l2.c:124 find_format_by_pix()
error: 'fmtdesc' dereferencing possible ERR_PTR()
drivers/usb/gadget/function/uvc_v4l2.c:392 uvc_v4l2_enum_format()
error: 'fmtdesc' dereferencing possible ERR_PTR()
Also, fix similar issue in uvc_v4l2_try_format() for potential
dereferencing of ERR_PTR().
Signed-off-by: Abhishek Tamboli <abhishektamboli9@gmail.com>
Link: https://lore.kernel.org/r/20240815102202.594812-1-abhishektamboli9@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add MODULE_DEVICE_TABLE(), so modules could be properly autoloaded
based on the alias from of_device_id table.
Signed-off-by: Liao Chen <liaochen4@huawei.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240814030443.3876203-1-liaochen4@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Modify CONNECTOR_RESET command implementation to accommodate
DATA_RESET reset type as defined in UCSI spec v2.0 and later.
Hard Reset bit field was defined with value 1 in UCSI spec version 1.0.
Starting with spec version 1.1, Hard Reset bit field was removed from the
CONNECTOR_RESET command, until spec 2.0 reintroduced it with value 0, so,
the value to pass in to the command for a Hard Reset is different depending
on the UCSI version supported by the LPM.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Venkat Jayaraman <venkat.jayaraman@intel.com>
Link: https://lore.kernel.org/r/20240813231828.1192338-1-pooja.katiyar@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
list_entry() will never return a NULL pointer, thus remove the
check.
Signed-off-by: Yuesong Li <liyuesong@vivo.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Link: https://lore.kernel.org/r/20240821085245.25348-1-liyuesong@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use scoped for_each_available_child_of_node_scoped() when iterating over
device nodes to make code a bit simpler.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Anand Moon <linux.amoon@gmail.com>
Link: https://lore.kernel.org/r/20240821071752.2335406-1-ruanjinjie@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use scoped for_each_available_child_of_node_scoped() when iterating over
device nodes to make code a bit simpler.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Anand Moon <linux.amoon@gmail.com>
Link: https://lore.kernel.org/r/20240821071856.2335529-1-ruanjinjie@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit addresses an issue where the USB core could access an
invalid event buffer address during runtime suspend, potentially causing
SMMU faults and other memory issues in Exynos platforms. The problem
arises from the following sequence.
1. In dwc3_gadget_suspend, there is a chance of a timeout when
moving the USB core to the halt state after clearing the
run/stop bit by software.
2. In dwc3_core_exit, the event buffer is cleared regardless of
the USB core's status, which may lead to an SMMU faults and
other memory issues. if the USB core tries to access the event
buffer address.
To prevent this hardware quirk on Exynos platforms, this commit ensures
that the event buffer address is not cleared by software when the USB
core is active during runtime suspend by checking its status before
clearing the buffer address.
Cc: stable <stable@kernel.org>
Signed-off-by: Selvarasu Ganesan <selvarasu.g@samsung.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240815064836.1491-1-selvarasu.g@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit '9329933699b3 ("soc: qcom: pmic_glink: Make client-lock
non-sleeping")' moved the pmic_glink client list under a spinlock, as it
is accessed by the rpmsg/glink callback, which in turn is invoked from
IRQ context.
This means that ucsi_unregister() is now called from atomic context,
which isn't feasible as it's expecting a sleepable context. An effort is
under way to get GLINK to invoke its callbacks in a sleepable context,
but until then lets schedule the unregistration.
A side effect of this is that ucsi_unregister() can now happen
after the remote processor, and thereby the communication link with it, is
gone. pmic_glink_send() is amended with a check to avoid the resulting NULL
pointer dereference.
This does however result in the user being informed about this error by
the following entry in the kernel log:
ucsi_glink.pmic_glink_ucsi pmic_glink.ucsi.0: failed to send UCSI write request: -5
Fixes: 9329933699 ("soc: qcom: pmic_glink: Make client-lock non-sleeping")
Cc: stable@vger.kernel.org
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Amit Pundir <amit.pundir@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Link: https://lore.kernel.org/r/20240820-pmic-glink-v6-11-races-v3-2-eec53c750a04@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
As pointed out by Stephen Boyd it is possible that during initialization
of the pmic_glink child drivers, the protection-domain notifiers fires,
and the associated work is scheduled, before the client registration
returns and as a result the local "client" pointer has been initialized.
The outcome of this is a NULL pointer dereference as the "client"
pointer is blindly dereferenced.
Timeline provided by Stephen:
CPU0 CPU1
---- ----
ucsi->client = NULL;
devm_pmic_glink_register_client()
client->pdr_notify(client->priv, pg->client_state)
pmic_glink_ucsi_pdr_notify()
schedule_work(&ucsi->register_work)
<schedule away>
pmic_glink_ucsi_register()
ucsi_register()
pmic_glink_ucsi_read_version()
pmic_glink_ucsi_read()
pmic_glink_ucsi_read()
pmic_glink_send(ucsi->client)
<client is NULL BAD>
ucsi->client = client // Too late!
This code is identical across the altmode, battery manager and usci
child drivers.
Resolve this by splitting the allocation of the "client" object and the
registration thereof into two operations.
This only happens if the protection domain registry is populated at the
time of registration, which by the introduction of commit '1ebcde047c54
("soc: qcom: add pd-mapper implementation")' became much more likely.
Reported-by: Amit Pundir <amit.pundir@linaro.org>
Closes: https://lore.kernel.org/all/CAMi1Hd2_a7TjA7J9ShrAbNOd_CoZ3D87twmO5t+nZxC9sX18tA@mail.gmail.com/
Reported-by: Johan Hovold <johan@kernel.org>
Closes: https://lore.kernel.org/all/ZqiyLvP0gkBnuekL@hovoldconsulting.com/
Reported-by: Stephen Boyd <swboyd@chromium.org>
Closes: https://lore.kernel.org/all/CAE-0n52JgfCBWiFQyQWPji8cq_rCsviBpW-m72YitgNfdaEhQg@mail.gmail.com/
Fixes: 58ef4ece1e ("soc: qcom: pmic_glink: Introduce base PMIC GLINK driver")
Cc: stable@vger.kernel.org
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Amit Pundir <amit.pundir@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Link: https://lore.kernel.org/r/20240820-pmic-glink-v6-11-races-v3-1-eec53c750a04@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
re-enumerating full-speed devices after a failed address device command
can trigger a NULL pointer dereference.
Full-speed devices may need to reconfigure the endpoint 0 Max Packet Size
value during enumeration. Usb core calls usb_ep0_reinit() in this case,
which ends up calling xhci_configure_endpoint().
On Panther point xHC the xhci_configure_endpoint() function will
additionally check and reserve bandwidth in software. Other hosts do
this in hardware
If xHC address device command fails then a new xhci_virt_device structure
is allocated as part of re-enabling the slot, but the bandwidth table
pointers are not set up properly here.
This triggers the NULL pointer dereference the next time usb_ep0_reinit()
is called and xhci_configure_endpoint() tries to check and reserve
bandwidth
[46710.713538] usb 3-1: new full-speed USB device number 5 using xhci_hcd
[46710.713699] usb 3-1: Device not responding to setup address.
[46710.917684] usb 3-1: Device not responding to setup address.
[46711.125536] usb 3-1: device not accepting address 5, error -71
[46711.125594] BUG: kernel NULL pointer dereference, address: 0000000000000008
[46711.125600] #PF: supervisor read access in kernel mode
[46711.125603] #PF: error_code(0x0000) - not-present page
[46711.125606] PGD 0 P4D 0
[46711.125610] Oops: Oops: 0000 [#1] PREEMPT SMP PTI
[46711.125615] CPU: 1 PID: 25760 Comm: kworker/1:2 Not tainted 6.10.3_2 #1
[46711.125620] Hardware name: Gigabyte Technology Co., Ltd.
[46711.125623] Workqueue: usb_hub_wq hub_event [usbcore]
[46711.125668] RIP: 0010:xhci_reserve_bandwidth (drivers/usb/host/xhci.c
Fix this by making sure bandwidth table pointers are set up correctly
after a failed address device command, and additionally by avoiding
checking for bandwidth in cases like this where no actual endpoints are
added or removed, i.e. only context for default control endpoint 0 is
evaluated.
Reported-by: Karel Balej <balejk@matfyz.cz>
Closes: https://lore.kernel.org/linux-usb/D3CKQQAETH47.1MUO22RTCH2O3@matfyz.cz/
Cc: stable@vger.kernel.org
Fixes: 651aaf36a7 ("usb: xhci: Handle USB transaction error on address command")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240815141117.2702314-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to define one in a custom structure. The tty_port one
is free to use.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Link: https://lore.kernel.org/r/20240808103549.429349-6-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to check against kfifo_len() before kfifo_out(). Just
ask the latter for data and it tells how much it retrieved. Or returns 0
in case there are no more.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Link: https://lore.kernel.org/r/20240808103549.429349-5-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the ability for the USB FunctionFS (FFS) gadget driver to be able
to create Device Firmware Upgrade (DFU) functional descriptors. [1]
This patch allows implementation of DFU in userspace using the
FFS gadget. The DFU protocol uses the control pipe (ep0) for all
messaging so only the addition of the DFU functional descriptor
is needed in the kernel driver.
The DFU functional descriptor is written to the ep0 file along with
any other descriptors during FFS setup. DFU requires an interface
descriptor followed by the DFU functional descriptor.
This patch includes documentation of the added descriptor for DFU
and conversion of some existing documentation to kernel-doc format
so that it can be included in the generated docs.
An implementation of DFU 1.1 that implements just the runtime descriptor
using the FunctionFS gadget (with rebooting into u-boot for DFU mode)
has been tested on an i.MX8 Nano.
An implementation of DFU 1.1 that implements both runtime and DFU mode
using the FunctionFS gadget has been tested on Xilinx Zynq UltraScale+.
Note that for the best performance of firmware update file transfers, the
userspace program should respond as quick as possible to the setup packets.
[1] https://www.usb.org/sites/default/files/DFU_1.1.pdf
Signed-off-by: David Sands <david.sands@biamp.com>
Co-developed-by: Chris Wulff <crwulff@gmail.com>
Signed-off-by: Chris Wulff <crwulff@gmail.com>
Link: https://lore.kernel.org/r/20240811000004.1395888-2-crwulff@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'struct config_item_type' is not modified in this file.
Apparently, these structures are only used with
config_group_init_type_name() which takes a const struct config_item_type*
as a 3rd argument.
Constifying this structure moves some data to a read-only section, so
increase overall security, especially when the structure holds some
function pointers.
On a x86_64, with allmodconfig:
Before:
======
text data bss dec hex filename
40834 5112 64 46010 b3ba drivers/usb/gadget/configfs.o
After:
=====
text data bss dec hex filename
41218 4728 64 46010 b3ba drivers/usb/gadget/configfs.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/513223e97082e1bb758e36d55c175ec9ea34a71c.1723323896.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"linux/usb/gadget_configfs.h" is only included in
"drivers/usb/gadget/configfs.c", so there is no need to declare a function
in the header file. it is only used in this .c file.
It's better to have it static.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/958cb49dca1bff4254a3492c018efbf3b01918b4.1723323107.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
for_each_node_with_property() can iterate through the device_node
with a given property name, and we don't need to find the device_node
in the while loop. Since of_device_is_available() will return false if
the "controller" is NULL and break the while loop, there is no functional
change with such conversion.
Signed-off-by: Zhang Zekun <zhangzekun11@huawei.com>
Link: https://lore.kernel.org/r/20240809082711.99085-1-zhangzekun11@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Similar to other platforms using the MUSB driver, PolarFire SoC lacks
an ID pin interrupt event, preventing several OTG-critical status
change events from being exposed. We need to rely on polling to detect
USB attach events for the dual-role port.
The otg state machine implementation is based on Texas Instruments
DA8xx/OMAP-L1x glue layer.
This has been tested on BeagleV-Fire with couple of devices in host mode
and with the Ethernet gadget driver in peripheral mode, in a wide
variety of plug orders.
Signed-off-by: Valentina Fernandez <valentina.fernandezalanis@microchip.com>
Link: https://lore.kernel.org/r/20240806131407.1542306-1-valentina.fernandezalanis@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1p1 is off when the system enters suspend at i.MX6UL. It cause the PHY
get wrong USB DP/DM value, then unexpected wakeup may occur if USB wakeup
enabled. This will enable weak 1p1 during PHY suspend if vbus exist. So
USB DP/DM is correct when system suspend.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20240726113207.3393247-5-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This wakeup setting can enable USB wakeup function even the
controller's power is lost, and both A7 and M4 are in VLLS mode.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20240726113207.3393247-4-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
IP require keep USBPHY2's clk always on, so USBPHY2 (PLL7) power can be
controlled by suspend signal. USB remote wakeup needs resume signal be
sent out as soon as possible to match USB requirements.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20240726113207.3393247-2-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable regulator 'phy-3p0' to pass eye diagram test since it improve signal
qualilty.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20240726113207.3393247-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tcpci_maxim currently never triggers the TCPM state machine when CC
status has not changed due to a contaminant but due to a real
connection event, i.e. a genuine plug event, meaning the system will
stay idle and not notify any subscribers.
The reason is that the initial state of the port is 'toggling', which
causes _max_tcpci_irq() to only drive the contamination part of the
TCPM state machine (via tcpm_port_clean()).
What should happen instead is that if no contamination was detected,
the TCPM should be notified of the CC change in this case.
To fix this, we update ...is_contaminant() to also allow its caller to
determine if more CC processing is required and then call into the TCPM
as required.
While at it, add a kernel-doc for max_contaminant_is_contaminant().
Note: the code has an issue where I2C errors during contaminant
detection also cause the TCPM state machine to not be updated. This
commit doesn't change this behaviour and should be addressed by
follow-up commit(s).
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240806-max33359-toggling-v2-1-a66ab37baafb@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add LJCA GPIO support for the Lunar Lake platform.
New HID taken from out of tree ivsc-driver git repo.
Link: 47e7c4a446
Cc: stable <stable@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240812095038.555837-1-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit bf20c69cf3.
During tcpm_init() stage, if the VBUS is still present after
tcpm_reset_port(), then we assume that VBUS will off and goto safe0v
after a specific discharge time. Following a TCPM_VBUS_EVENT event if
VBUS reach to off state. TCPM_VBUS_EVENT event may be set during
PORT_RESET handling stage. If pd_events reset to 0 after TCPM_VBUS_EVENT
set, we will lost this VBUS event. Then the port state machine may stuck
at one state.
Before:
[ 2.570172] pending state change PORT_RESET -> PORT_RESET_WAIT_OFF @ 100 ms [rev1 NONE_AMS]
[ 2.570179] state change PORT_RESET -> PORT_RESET_WAIT_OFF [delayed 100 ms]
[ 2.570182] pending state change PORT_RESET_WAIT_OFF -> SNK_UNATTACHED @ 920 ms [rev1 NONE_AMS]
[ 3.490213] state change PORT_RESET_WAIT_OFF -> SNK_UNATTACHED [delayed 920 ms]
[ 3.490220] Start toggling
[ 3.546050] CC1: 0 -> 0, CC2: 0 -> 2 [state TOGGLING, polarity 0, connected]
[ 3.546057] state change TOGGLING -> SRC_ATTACH_WAIT [rev1 NONE_AMS]
After revert this patch, we can see VBUS off event and the port will goto
expected state.
[ 2.441992] pending state change PORT_RESET -> PORT_RESET_WAIT_OFF @ 100 ms [rev1 NONE_AMS]
[ 2.441999] state change PORT_RESET -> PORT_RESET_WAIT_OFF [delayed 100 ms]
[ 2.442002] pending state change PORT_RESET_WAIT_OFF -> SNK_UNATTACHED @ 920 ms [rev1 NONE_AMS]
[ 2.442122] VBUS off
[ 2.442125] state change PORT_RESET_WAIT_OFF -> SNK_UNATTACHED [rev1 NONE_AMS]
[ 2.442127] VBUS VSAFE0V
[ 2.442351] CC1: 0 -> 0, CC2: 0 -> 0 [state SNK_UNATTACHED, polarity 0, disconnected]
[ 2.442357] Start toggling
[ 2.491850] CC1: 0 -> 0, CC2: 0 -> 2 [state TOGGLING, polarity 0, connected]
[ 2.491858] state change TOGGLING -> SRC_ATTACH_WAIT [rev1 NONE_AMS]
[ 2.491863] pending state change SRC_ATTACH_WAIT -> SNK_TRY @ 200 ms [rev1 NONE_AMS]
[ 2.691905] state change SRC_ATTACH_WAIT -> SNK_TRY [delayed 200 ms]
Fixes: bf20c69cf3 ("usb: typec: tcpm: clear pd_event queue in PORT_RESET")
Cc: stable@vger.kernel.org
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240809112901.535072-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The command execution routines need to return the amount of
data that was transferred when succesful.
This fixes an issue where the alternate modes and the power
delivery capabilities are not getting registered.
Fixes: 5e9c1662a8 ("usb: typec: ucsi: rework command execution functions")
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240809150343.286942-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stall handling is managed in the 'process_*' functions, which are called
right before the 'goto' stall handling code snippet. Thus, there should
be a return after the 'process_*' functions. Otherwise, the stall code may
run twice.
Fixes: 1b349f214a ("usb: xhci: add 'goto' for halted endpoint check in handle_tx_event()")
Reported-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240809124408.505786-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If xhci_mem_init() fails, it calls into xhci_mem_cleanup() to mop
up the damage. If it fails early enough, before xhci->interrupters
is allocated but after xhci->max_interrupters has been set, which
happens in most (all?) cases, things get uglier, as xhci_mem_cleanup()
unconditionally derefences xhci->interrupters. With prejudice.
Gate the interrupt freeing loop with a check on xhci->interrupters
being non-NULL.
Found while debugging a DMA allocation issue that led the XHCI driver
on this exact path.
Fixes: c99b38c412 ("xhci: add support to allocate several interrupters")
Cc: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: Wesley Cheng <quic_wcheng@quicinc.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org # 6.8+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240809124408.505786-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If CONFIG_USB_XHCI_PCI_RENESAS is enabled, xhci-pci conditionally
calls into the xhci-pci-renesas module, which means both modules must
be loaded to use any xHCI PCI controller.
The MODULE_FIRMWARE declaration in the base xhci-pci module causes
initramfs-tools to check for and warn about missing firmware for the
Renesas xHCI controllers, when any xHCI PCI controller is present.
And because of the previous oddity, simply moving this declaration to
xhci-pci-renesas wouldn't help.
To fix this, reverse the relationship between the modules:
- Remove the quirk for the Renesas xHCIs, and the driver_data
structure used only for them
- In xhci-pci:
- Rename xhci_pci_probe() to xhci_pci_common_probe()
- Export xhci_pci_common_probe() and xhci_pci_remove()
- Use a new probe function that rejects the Renesas xHCIs and then
calls the common probe function
- In xhci-pci-renesas:
- Stop exporting renesas_xhci_check_request_fw()
- Add a probe function that calls renesas_xhci_check_request_fw()
followed by xhci_pci_common_probe()
- Add and register a new pci_driver matching only the Renesas xHCIs
and using its own probe function, but with other operations the
same as in xhci-pci
- Make CONFIG_USB_XHCI_PCI_RENESAS depend on CONFIG_USB_XHCI_PCI,
not the other way around
Finally, move the MODULE_FIRMWARE declaration to xhci-pci-renesas.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Tested-by: Cyril Brulebois <cyril@debamax.com>
Link: https://lore.kernel.org/r/ZqqfXYRJf7kGaqus@decadent.org.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's no need to get the length of an DT array property before
parsing the array. of_property_read_variable_u32_array() takes a minimum
and maximum length and returns the actual length (or error code).
This is part of a larger effort to remove callers of of_find_property()
and similar functions. of_find_property() leaks the DT struct property
and data pointers which is a problem for dynamically allocated nodes
which may be freed.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240731201407.1838385-5-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace SET_RUNTIME_PM_OPS()/SET SYSTEM_SLEEP_PM_OPS() with their modern
RUNTIME_PM_OPS() and SYSTEM_SLEEP_PM_OPS() alternatives.
The combined usage of pm_ptr() and RUNTIME_PM_OPS/SYSTEM_SLEEP_PM_OPS()
allows the compiler to evaluate if the runtime suspend/resume() functions
are used at build time or are simply dead code.
This allows removing the __maybe_unused notation from the runtime
suspend/resume() functions.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240806114231.2603055-1-festevam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert array initializers to C99 syntax by adding the '=' after
each designated initializer.
Fix the following smatch warnings:
drivers/usb/gadget/function/u_audio.c:1117:20:
warning: obsolete array initializer, use C99 syntax
drivers/usb/gadget/function/u_audio.c:1124:28:
warning: obsolete array initializer, use C99 syntax
drivers/usb/gadget/function/u_audio.c:1131:19:
warning: obsolete array initializer, use C99 syntax
drivers/usb/gadget/function/u_audio.c:1138:27:
warning: obsolete array initializer, use C99 syntax
drivers/usb/gadget/function/u_audio.c:1145:25:
warning: obsolete array initializer, use C99 syntax
Also, fix two checkpatch.pl warnings:
WARNING: please, no spaces at the start of a line
+ [UAC_FBACK_CTRL] = {$
WARNING: please, no spaces at the start of a line
+ [UAC_MUTE_CTRL] = {$
Signed-off-by: Abhishek Tamboli <abhishektamboli9@gmail.com>
Reviewed-by: Ricardo B. Marliere <ricardo@marliere.net>
Link: https://lore.kernel.org/r/20240801190209.500373-1-abhishektamboli9@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use of_property_present() to test for property presence rather than
of_get_property(). This is part of a larger effort to remove callers
of of_get_property() and similar functions. of_get_property() leaks
the DT property data pointer which is a problem for dynamically
allocated nodes which may be freed.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20240731191312.1710417-18-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of open-coding the call to tcpci_unregister_port() in various
places, let's just register a hook using devm_add_action_or_reset() so
that it gets called automatically as and when necessary by the device
management APIs.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240710-tcpc-cleanup-v1-15-0ec1f41f4263@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dev_err_probe() exists as a useful helper ensuring standardized
error messages during .probe() and using it also helps to make
the code more legible.
Use it.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240710-tcpc-cleanup-v1-14-0ec1f41f4263@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert register TCPC_VENDOR_ADC_CTRL1 to using GENMASK() and
FIELD_PREP() so as to keep using a similar approach throughout the code
base and make it arguably easier to read.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240710-tcpc-cleanup-v1-13-0ec1f41f4263@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert register TCPC_VENDOR_CC_CTRL3 to using GENMASK() so as to keep
using a similar approach throughout the code base and make it arguably
easier to read.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240710-tcpc-cleanup-v1-12-0ec1f41f4263@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert register TCPC_VENDOR_CC_CTRL2 to using GENMASK() and
FIELD_PREP() so as to keep using a similar approach throughout the code
base and make it arguably easier to read.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240710-tcpc-cleanup-v1-11-0ec1f41f4263@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only one user of STATUS_CHECK() remains, and the code can actually be
made more legible by simply avoiding the use of that wrapper macro,
allowing to also drop the macro altogether.
Do so.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240710-tcpc-cleanup-v1-10-0ec1f41f4263@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need for using the ternary if/else here, simply mask
TCPC_ALERT_RX_BUF_OVF as necessary, which arguably makes the code
easier to read.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240710-tcpc-cleanup-v1-9-0ec1f41f4263@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This makes it easier to see what's missing and what's being programmed.
While at it, add brackets to help with formatting and remove a comment
that doesn't add much value.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240710-tcpc-cleanup-v1-8-0ec1f41f4263@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert all fields from register TCPC_TRANSMIT to using GENMASK() and
FIELD_PREP() so as to keep using a similar approach throughout the code
base and make it arguably easier to read.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240710-tcpc-cleanup-v1-7-0ec1f41f4263@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert field TCPC_MSG_HDR_INFO_REV from register TCPC_MSG_HDR_INFO to
using GENMASK() and FIELD_PREP() so as to keep using a similar approach
for all fields.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240710-tcpc-cleanup-v1-6-0ec1f41f4263@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Align the last remaining field TCPC_ROLE_CTRL_RP_VAL with the other
fields in the TCPC_ROLE_CTRL register by using GENMASK() and
FIELD_PREP().
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240710-tcpc-cleanup-v1-5-0ec1f41f4263@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All this open-coded shifting and masking is quite hard to read, in
particular the if-statement in tcpci_apply_rc().
Declare TCPC_ROLE_CTRL_CC[12] using GENMASK() which allows using
FIELD_GET() and FIELD_PREP() to arguably make the code more legible.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240710-tcpc-cleanup-v1-4-0ec1f41f4263@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The existing code here, particularly in maxim_contaminant.c, is
arguably quite hard to read due to the open-coded masking and shifting
spanning multiple lines.
Use GENMASK() and FIELD_GET() instead, which arguably make the code
much easier to follow.
While at it, use the symbolic name TCPC_CC_STATE_SRC_OPEN for one
instance of open-coded 0x0.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240710-tcpc-cleanup-v1-3-0ec1f41f4263@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We loop while the status is != 0, so rephrase the comment slightly for
clarity.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240710-tcpc-cleanup-v1-2-0ec1f41f4263@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function returns with the ppm_lock held if the PPM is
busy or there's an error.
Reported-and-tested-by: Luciano Coelho <luciano.coelho@intel.com>
Fixes: 5e9c1662a8 ("usb: typec: ucsi: rework command execution functions")
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reported-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20240806112029.2984319-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit (122968f8dd usb: typec: tcpm: avoid resets for missing
source capability messages), state will change from SNK_WAIT_CAPABILITIES
to SNK_WAIT_CAPABILITIES_TIMEOUT. We need to change SNK_WAIT_CAPABILITIES
-> SNK_READY path to SNK_WAIT_CAPABILITIES_TIMEOUT -> SNK_READY
accordingly. Otherwise, the sink port will never change to SNK_READY state
if the source does't have PD capability.
[ 503.547183] pending state change SNK_WAIT_CAPABILITIES -> SNK_WAIT_CAPABILITIES_TIMEOUT @ 310 ms [rev3 NONE_AMS]
[ 503.857239] state change SNK_WAIT_CAPABILITIES -> SNK_WAIT_CAPABILITIES_TIMEOUT [delayed 310 ms]
[ 503.857254] PD TX, header: 0x87
[ 503.862440] PD TX complete, status: 2
[ 503.862484] state change SNK_WAIT_CAPABILITIES_TIMEOUT -> SNK_UNATTACHED [rev3 NONE_AMS]
Fixes: 122968f8dd ("usb: typec: tcpm: avoid resets for missing source capability messages")
Cc: stable@vger.kernel.org
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20240802064156.1846768-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ``alt`` parameter was used as a way to differentiate between
f->disable() and f->set_alt(). As the code paths diverge quite a bit,
pull out the f->disable() code from ffs_func_set_alt(), everything will
become clearer and less error prone. No change in functionality
intended.
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/20240802140428.2000312-3-tudor.ambarus@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The blamed commit made ffs_func_disable() always return -EINVAL as the
method calls ffs_func_set_alt() with the ``alt`` argument being
``(unsigned)-1``, which is always greater than MAX_ALT_SETTINGS.
Use the MAX_ALT_SETTINGS check just in the f->set_alt() code path,
f->disable() doesn't care about the ``alt`` parameter.
Make a surgical fix, but really the f->disable() code shall be pulled
out from ffs_func_set_alt(), the code will become clearer. A patch will
follow.
Note that ffs_func_disable() always returning -EINVAL made pixel6 crash
on USB disconnect.
Fixes: 2f550553e2 ("usb: gadget: f_fs: Add the missing get_alt callback")
Cc: stable <stable@kernel.org>
Reported-by: William McVicker <willmcvicker@google.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/20240802140428.2000312-2-tudor.ambarus@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's a fix for an issue when using the usb_debug driver with Xen.
This change has been in linux-next for a couple of days with no reported
issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCZqzlPgAKCRALxc3C7H1l
CEU7AQDrMHfvMa3ZOoR3A/i7VM3Nwy4hKTk+xAD7Y6st3L17YAD+JZ6OykxBzxh0
xINnvnaZBTtRHf8cirUkk5SUJW7Mzwg=
=jrO8
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-6.11-rc2' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fix for 6.11-rc2
Here's a fix for an issue when using the usb_debug driver with Xen.
This change has been in linux-next for a couple of days with no reported
issues.
* tag 'usb-serial-6.11-rc2' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: debug: do not echo input by default
This driver is intended as a "client" end of the console connection.
When connected to a host it's supposed to receive debug logs, and
possibly allow to interact with whatever debug console is available
there. Feeding messages back, depending on a configuration may cause log
messages be executed as shell commands (which can be really bad if one
is unlucky, imagine a log message like "prevented running `rm -rf
/home`"). In case of Xen, it exposes sysrq-like debug interface, and
feeding it its own logs will pretty quickly hit 'R' for "instant
reboot".
Contrary to a classic serial console, the USB one cannot be configured
ahead of time, as the device shows up only when target OS is up. And at
the time device is opened to execute relevant ioctl, it's already too
late, especially when logs start flowing shortly after device is
initialized.
Avoid the issue by changing default to no echo for this type of devices.
Signed-off-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
[ johan: amend summary; disable also ECHONL ]
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
On resume of the Raspberry Pi the dwc2 driver fails to enable
HCD_FLAG_HW_ACCESSIBLE before re-enabling the interrupts.
This causes a situation where both handler ignore a incoming port
interrupt and force the upper layers to disable the dwc2 interrupt line.
This leaves the USB interface in a unusable state:
irq 66: nobody cared (try booting with the "irqpoll" option)
CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W 6.10.0-rc3
Hardware name: BCM2835
Call trace:
unwind_backtrace from show_stack+0x10/0x14
show_stack from dump_stack_lvl+0x50/0x64
dump_stack_lvl from __report_bad_irq+0x38/0xc0
__report_bad_irq from note_interrupt+0x2ac/0x2f4
note_interrupt from handle_irq_event+0x88/0x8c
handle_irq_event from handle_level_irq+0xb4/0x1ac
handle_level_irq from generic_handle_domain_irq+0x24/0x34
generic_handle_domain_irq from bcm2836_chained_handle_irq+0x24/0x28
bcm2836_chained_handle_irq from generic_handle_domain_irq+0x24/0x34
generic_handle_domain_irq from generic_handle_arch_irq+0x34/0x44
generic_handle_arch_irq from __irq_svc+0x88/0xb0
Exception stack(0xc1b01f20 to 0xc1b01f68)
1f20: 0005c0d4 00000001 00000000 00000000 c1b09780 c1d6b32c c1b04e54 c1a5eae8
1f40: c1b04e90 00000000 00000000 00000000 c1d6a8a0 c1b01f70 c11d2da8 c11d4160
1f60: 60000013 ffffffff
__irq_svc from default_idle_call+0x1c/0xb0
default_idle_call from do_idle+0x21c/0x284
do_idle from cpu_startup_entry+0x28/0x2c
cpu_startup_entry from kernel_init+0x0/0x12c
handlers:
[<f539e0f4>] dwc2_handle_common_intr
[<75cd278b>] usb_hcd_irq
Disabling IRQ #66
Disabling clock gating workaround this issue.
Fixes: 0112b7ce68 ("usb: dwc2: Update dwc2_handle_usb_suspend_intr function.")
Link: https://lore.kernel.org/linux-usb/3fd0c2fb-4752-45b3-94eb-42352703e1fd@gmx.net/T/
Link: https://lore.kernel.org/all/5e8cbce0-3260-2971-484f-fc73a3b2bd28@synopsys.com/
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Link: https://lore.kernel.org/r/20240728130029.78279-5-wahrenst@gmx.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit c4a0f7a6ab ("usb: dwc2: Skip clock gating on Samsung
SoCs") introduced a parameter to skip enabling clock gating mode
even the hardware platform should supports it.
In order to make this more visible also print this in show
parameters of debugfs.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240728130029.78279-3-wahrenst@gmx.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bindings require two compatibles to be used: qcom,sc7280-eud
followed by fallback qcom,eud. The convention is to use fallback
compatible in OF device ID tables, unless some device-specific quirks
are needed.
This will also simplify matching any new devices - they will use
existing OF device ID entry, instead of adding a new one.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240731054438.9073-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add icount support for the transmitting and receiving characters. This
will make the tty LED trigger work with the ttyGS devices.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Link: https://lore.kernel.org/r/20240730193840.2580358-1-mwalle@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove unnecessary semicolon at the end of the switch statement.
This is detected by coccinelle.
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240715073947.4028319-1-nichen@iscas.ac.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add USB_SPEED_SUPER_PLUS as valid argument to allow
to attach USB SuperSpeed+ devices. Update speed of
virtual HC to SuperSpeed+ as well.
Signed-off-by: Łukasz Bartosik <ukaszb@chromium.org>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20240715131131.3876380-1-ukaszb@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "ohci-littledian" compatible has typo (edian->endian) and is not
used in in-kernel DTS. Considering the typo and that it is an very old
driver (~2006), drop the compatible.
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240712120947.86181-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There shouldn't be a ; at the end of the function, delete it.
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Reviewed-by: Javier Carrasco <javier.carrasco@wolfvision.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240724162356.992763-2-harshit.m.mogalapalli@oracle.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
release_firmware() already frees fw, fix this my moving release_firmware
after the dereference.
Fixes: 916b8e5fa7 ("usb: typec: tipd: add error log to provide firmware name and size")
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Javier Carrasco <javier.carrasco@wolfvision.net>
Link: https://lore.kernel.org/r/20240724162356.992763-1-harshit.m.mogalapalli@oracle.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Upstream commit aba3a8d01d ("usb: gadget: u_serial: add suspend
resume callbacks") added started_delayed flag, so that new ports
which are opened after USB suspend can start IO while resuming.
But if the port was already opened, and gadget suspend kicks in
afterwards, start_delayed will never be set. This causes resume
to bail out before calling gs_start_io(). Fix this by setting
start_delayed during suspend.
Fixes: aba3a8d01d ("usb: gadget: u_serial: add suspend resume callbacks")
Cc: stable@vger.kernel.org
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Link: https://lore.kernel.org/r/20240730125754.576326-1-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tcpci_check_std_output_cap() function is supposed to return negative
error codes but it's declared as type bool so the error handling doesn't
work. Declare it as an int instead.
Fixes: 62ce9ef147 ("usb: typec: tcpci: add support to set connector orientation")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/b0880888-6719-4614-91fc-8ee63b71d304@stanley.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the driver will happily register the switch/mux devices, and
so long as the i2c master doesn't complain, the user would never know
there's something wrong.
Add a device id check (based on [1]) and return -ENODEV if the read
fails or returns nonsense.
Checking the value on a Qualcomm SM6115P-based Lenovo Tab P11 tablet,
the ID mentioned in the datasheet does indeed show up:
fsa4480 1-0042: Found FSA4480 v1.1 (Vendor ID = 0)
[1] https://www.onsemi.com/pdf/datasheet/fsa4480-d.pdf
Fixes: 1dc246320c ("usb: typec: mux: Add On Semi fsa4480 driver")
Cc: stable <stable@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240729-topic-fs4480_check-v3-1-f5bf732d3424@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure the descriptor has been set before looking at maxpacket.
This fixes a null pointer panic in this case.
This may happen if the gadget doesn't properly set up the endpoint
for the current speed, or the gadget descriptors are malformed and
the descriptor for the speed/endpoint are not found.
No current gadget driver is known to have this problem, but this
may cause a hard-to-find bug during development of new gadgets.
Fixes: 54f83b8c8e ("USB: gadget: Reject endpoints with 0 maxpacket value")
Cc: stable@vger.kernel.org
Signed-off-by: Chris Wulff <crwulff@gmail.com>
Link: https://lore.kernel.org/r/20240725010419.314430-2-crwulff@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At a few places the driver carries stale pointers
to references that can still be used. Make sure that does not happen.
This strictly speaking closes ZDI-CAN-22273, though there may be
similar races in the driver.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@kernel.org>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20240709113851.14691-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These functions can fail if descriptors are malformed, or missing,
for the selected USB speed.
Fixes: eb9fecb9e6 ("usb: gadget: f_uac2: split out audio core")
Fixes: 24f779dac8 ("usb: gadget: f_uac2/u_audio: add feedback endpoint support")
Cc: stable@vger.kernel.org
Signed-off-by: Chris Wulff <crwulff@gmail.com>
Link: https://lore.kernel.org/r/20240721192314.3532697-2-crwulff@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the block number 0xff is given to Function Block Discovery
message, the device should return the information of all Function
Blocks, but currently the gadget driver treats it as an error.
Implement the proper behavior for the block 0xff instead.
Fixes: 8b645922b2 ("usb: gadget: Add support for USB MIDI 2.0 function driver")
Cc: stable@vger.kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20240717095102.10493-1-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are the USB-serial updates for 6.11-rc1, including:
- add missing module descriptions
- add flexible array annotation in garmin_gps
Included are also various clean ups.
All have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCZpUUagAKCRALxc3C7H1l
CItIAP9fUATObt8KBw5NPACzMVzZAsJ2p6bs19Sawoc5WVM9QwD+O3RXTx1e4LzA
57YKyYdeqsKWFpg//wuiUJK3mWID0wU=
=YVja
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-6.11-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial updates for 6.11-rc1
Here are the USB-serial updates for 6.11-rc1, including:
- add missing module descriptions
- add flexible array annotation in garmin_gps
Included are also various clean ups.
All have been in linux-next with no reported issues.
* tag 'usb-serial-6.11-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: garmin_gps: use struct_size() to allocate pkt
USB: serial: garmin_gps: annotate struct garmin_packet with __counted_by
USB: serial: add missing MODULE_DESCRIPTION() macros
USB: serial: spcp8x5: remove unused struct 'spcp8x5_usb_ctrl_arg'
- Treewide conversion of of_property_for_each_u32() to drop internal
arguments making struct property opaque
- Add binding for Amlogic A4 SoC watchdog
- Fix constraints for AD7192 'single-channel' property
-----BEGIN PGP SIGNATURE-----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=Nn/d
-----END PGP SIGNATURE-----
Merge tag 'devicetree-fixes-for-6.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull more devicetree updates from Rob Herring:
"Most of this is a treewide change to of_property_for_each_u32() which
was small enough to do in one go before rc1 and avoids the need to
create of_property_for_each_u32_some_new_name().
- Treewide conversion of of_property_for_each_u32() to drop internal
arguments making struct property opaque
- Add binding for Amlogic A4 SoC watchdog
- Fix constraints for AD7192 'single-channel' property"
* tag 'devicetree-fixes-for-6.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: iio: adc: ad7192: Fix 'single-channel' constraints
of: remove internal arguments from of_property_for_each_u32()
dt-bindings: watchdog: add support for Amlogic A4 SoCs
Here is the big set of driver core changes for 6.11-rc1.
Lots of stuff in here, with not a huge diffstat, but apis are evolving
which required lots of files to be touched. Highlights of the changes
in here are:
- platform remove callback api final fixups (Uwe took many releases to
get here, finally!)
- Rust bindings for basic firmware apis and initial driver-core
interactions. It's not all that useful for a "write a whole driver
in rust" type of thing, but the firmware bindings do help out the
phy rust drivers, and the driver core bindings give a solid base on
which others can start their work. There is still a long way to go
here before we have a multitude of rust drivers being added, but
it's a great first step.
- driver core const api changes. This reached across all bus types,
and there are some fix-ups for some not-common bus types that
linux-next and 0-day testing shook out. This work is being done to
help make the rust bindings more safe, as well as the C code, moving
toward the end-goal of allowing us to put driver structures into
read-only memory. We aren't there yet, but are getting closer.
- minor devres cleanups and fixes found by code inspection
- arch_topology minor changes
- other minor driver core cleanups
All of these have been in linux-next for a very long time with no
reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZqH+aQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymoOQCfVBdLcBjEDAGh3L8qHRGMPy4rV2EAoL/r+zKm
cJEYtJpGtWX6aAtugm9E
=ZyJV
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the big set of driver core changes for 6.11-rc1.
Lots of stuff in here, with not a huge diffstat, but apis are evolving
which required lots of files to be touched. Highlights of the changes
in here are:
- platform remove callback api final fixups (Uwe took many releases
to get here, finally!)
- Rust bindings for basic firmware apis and initial driver-core
interactions.
It's not all that useful for a "write a whole driver in rust" type
of thing, but the firmware bindings do help out the phy rust
drivers, and the driver core bindings give a solid base on which
others can start their work.
There is still a long way to go here before we have a multitude of
rust drivers being added, but it's a great first step.
- driver core const api changes.
This reached across all bus types, and there are some fix-ups for
some not-common bus types that linux-next and 0-day testing shook
out.
This work is being done to help make the rust bindings more safe,
as well as the C code, moving toward the end-goal of allowing us to
put driver structures into read-only memory. We aren't there yet,
but are getting closer.
- minor devres cleanups and fixes found by code inspection
- arch_topology minor changes
- other minor driver core cleanups
All of these have been in linux-next for a very long time with no
reported problems"
* tag 'driver-core-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (55 commits)
ARM: sa1100: make match function take a const pointer
sysfs/cpu: Make crash_hotplug attribute world-readable
dio: Have dio_bus_match() callback take a const *
zorro: make match function take a const pointer
driver core: module: make module_[add|remove]_driver take a const *
driver core: make driver_find_device() take a const *
driver core: make driver_[create|remove]_file take a const *
firmware_loader: fix soundness issue in `request_internal`
firmware_loader: annotate doctests as `no_run`
devres: Correct code style for functions that return a pointer type
devres: Initialize an uninitialized struct member
devres: Fix memory leakage caused by driver API devm_free_percpu()
devres: Fix devm_krealloc() wasting memory
driver core: platform: Switch to use kmemdup_array()
driver core: have match() callback in struct bus_type take a const *
MAINTAINERS: add Rust device abstractions to DRIVER CORE
device: rust: improve safety comments
MAINTAINERS: add Danilo as FIRMWARE LOADER maintainer
MAINTAINERS: add Rust FW abstractions to FIRMWARE LOADER
firmware: rust: improve safety comments
...
The of_property_for_each_u32() macro needs five parameters, two of which
are primarily meant as internal variables for the macro itself (in the
for() clause). Yet these two parameters are used by a few drivers, and this
can be considered misuse or at least bad practice.
Now that the kernel uses C11 to build, these two parameters can be avoided
by declaring them internally, thus changing this pattern:
struct property *prop;
const __be32 *p;
u32 val;
of_property_for_each_u32(np, "xyz", prop, p, val) { ... }
to this:
u32 val;
of_property_for_each_u32(np, "xyz", val) { ... }
However two variables cannot be declared in the for clause even with C11,
so declare one struct that contain the two variables we actually need. As
the variables inside this struct are not meant to be used by users of this
macro, give the struct instance the noticeable name "_it" so it is visible
during code reviews, helping to avoid new code to use it directly.
Most usages are trivially converted as they do not use those two
parameters, as expected. The non-trivial cases are:
- drivers/clk/clk.c, of_clk_get_parent_name(): easily doable anyway
- drivers/clk/clk-si5351.c, si5351_dt_parse(): this is more complex as the
checks had to be replicated in a different way, making code more verbose
and somewhat uglier, but I refrained from a full rework to keep as much
of the original code untouched having no hardware to test my changes
All the changes have been build tested. The few for which I have the
hardware have been runtime-tested too.
Reviewed-by: Andre Przywara <andre.przywara@arm.com> # drivers/clk/sunxi/clk-simple-gates.c, drivers/clk/sunxi/clk-sun8i-bus-gates.c
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> # drivers/gpio/gpio-brcmstb.c
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> # drivers/irqchip/irq-atmel-aic-common.c
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # drivers/iio/adc/ti_am335x_adc.c
Acked-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com> # drivers/pwm/pwm-samsung.c
Acked-by: Richard Leitner <richard.leitner@linux.dev> # drivers/usb/misc/usb251xb.c
Acked-by: Mark Brown <broonie@kernel.org> # sound/soc/codecs/arizona.c
Reviewed-by: Richard Fitzgerald <rf@opensource.cirrus.com> # sound/soc/codecs/arizona.c
Acked-by: Michael Ellerman <mpe@ellerman.id.au> # arch/powerpc/sysdev/xive/spapr.c
Acked-by: Stephen Boyd <sboyd@kernel.org> # clk
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Acked-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20240724-of_property_for_each_u32-v3-1-bea82ce429e2@bootlin.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
-----BEGIN PGP SIGNATURE-----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=vw2i
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.11-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Define PCIE_RESET_CONFIG_DEVICE_WAIT_MS for the generic 100ms
required after reset before config access (Kevin Xie)
- Define PCIE_T_RRS_READY_MS for the generic 100ms required after
reset before config access (probably should be unified with
PCIE_RESET_CONFIG_DEVICE_WAIT_MS) (Damien Le Moal)
Resource management:
- Rename find_resource() to find_resource_space() to be more
descriptive (Ilpo Järvinen)
- Export find_resource_space() for use by PCI core, which needs to
learn whether there is available space for a bridge window (Ilpo
Järvinen)
- Prevent double counting of resources so window size doesn't grow on
each remove/rescan cycle (Ilpo Järvinen)
- Relax bridge window sizing algorithm so a device doesn't break
simply because it was removed and rescanned (Ilpo Järvinen)
- Evaluate the ACPI PRESERVE_BOOT_CONFIG _DSM in
pci_register_host_bridge() (not acpi_pci_root_create()) so we can
unify it with similar DT functionality (Vidya Sagar)
- Extend use of DT "linux,pci-probe-only" property so it works
per-host bridge as well as globally (Vidya Sagar)
- Unify support for ACPI PRESERVE_BOOT_CONFIG _DSM and the DT
"linux,pci-probe-only" property in pci_preserve_config() (Vidya
Sagar)
Driver binding:
- Add devres infrastructure for managed request and map of partial
BAR resources (Philipp Stanner)
- Deprecate pcim_iomap_table() because uses like
"pcim_iomap_table()[0]" have no good way to return errors (Philipp
Stanner)
- Add an always-managed pcim_request_region() for use instead of
pci_request_region() and similar, which are sometimes managed
depending on whether pcim_enable_device() has been called
previously (Philipp Stanner)
- Reimplement pcim_set_mwi() so it doesn't need to keep store MWI
state (Philipp Stanner)
- Add pcim_intx() for use instead of pci_intx(), which is sometimes
managed depending on whether pcim_enable_device() has been called
previously (Philipp Stanner)
- Add managed pcim_iomap_range() to allow mapping of a partial BAR
(Philipp Stanner)
- Fix a devres mapping leak in drm/vboxvideo (Philipp Stanner)
Error handling:
- Add missing bridge locking in device reset path and add a warning
for other possible lock issues (Dan Williams)
- Fix use-after-free on concurrent DPC and hot-removal (Lukas Wunner)
Power management:
- Disable AER and DPC during suspend to avoid spurious wakeups if
they share an interrupt with PME (Kai-Heng Feng)
PCIe native device hotplug:
- Detect if a device was removed or replaced during system sleep so
we don't assume a new device is the one that used to be there
(Lukas Wunner)
Virtualization:
- Add an ACS quirk for Broadcom BCM5760X multi-function NIC; it
prevents transactions between functions even though it doesn't
advertise ACS, so the functions can be attached individually via
VFIO (Ajit Khaparde)
Peer-to-peer DMA:
- Add a "pci=config_acs=" kernel command-line parameter to relax
default ACS settings to enable additional peer-to-peer
configurations. Requires expert knowledge of topology and ACS
operation (Vidya Sagar)
Endpoint framework:
- Remove unused struct pci_epf_group.type_group (Christophe JAILLET)
- Fix error handling in vpci_scan_bus() and epf_ntb_epc_cleanup()
(Dan Carpenter)
- Make struct pci_epc_class constant (Greg Kroah-Hartman)
- Remove unused pci_endpoint_test_bar_{readl,writel} functions
(Jiapeng Chong)
- Rename "BME" to "Bus Master Enable" (Manivannan Sadhasivam)
- Rename struct pci_epc_event_ops.core_init() callback to epc_init()
(Manivannan Sadhasivam)
- Move DMA init to MHI .epc_init() callback for uniformity
(Manivannan Sadhasivam)
- Cancel EPF test delayed work when link goes down (Manivannan
Sadhasivam)
- Add struct pci_epc_event_ops.epc_deinit() callback for cleanup
needed on fundamental reset (Manivannan Sadhasivam)
- Add 64KB alignment to endpoint test to support Rockchip rk3588
(Niklas Cassel)
- Optimize endpoint test by using memcpy() instead of readl() (Niklas
Cassel)
Device tree bindings:
- Add generic "ats-supported" property to advertise that a PCIe Root
Complex supports ATS (Jean-Philippe Brucker)
Amazon Annapurna Labs PCIe controller driver:
- Validate IORESOURCE_BUS presence to avoid NULL pointer dereference
(Aleksandr Mishin)
Axis ARTPEC-6 PCIe controller driver:
- Rename .cpu_addr_fixup() parameter to reflect that it is a PCI
address, not a CPU address (Niklas Cassel)
Freescale i.MX6 PCIe controller driver:
- Convert to agnostic GPIO API (Andy Shevchenko)
Freescale Layerscape PCIe controller driver:
- Make struct mobiveil_rp_ops constant (Christophe JAILLET)
- Use new generic dw_pcie_ep_linkdown() to handle link-down events
(Manivannan Sadhasivam)
HiSilicon Kirin PCIe controller driver:
- Convert to agnostic GPIO API (Andy Shevchenko)
- Use _scoped() iterator for OF children to ensure refcounts are
decremented at loop exit (Javier Carrasco)
Intel VMD host bridge driver:
- Create sysfs "domain" symlink before downstream devices are exposed
to userspace by pci_bus_add_devices() (Jiwei Sun)
Loongson PCIe controller driver:
- Enable MSI when LS7A is used with new CPUs that have integrated
PCIe Root Complex, e.g., Loongson-3C6000, so downstream devices can
use MSI (Huacai Chen)
Microchip AXI PolarFlare PCIe controller driver:
- Move pcie-microchip-host.c to a new PLDA directory (Minda Chen)
- Factor PLDA generic items out to a common
plda,xpressrich3-axi-common.yaml binding (Minda Chen)
- Factor PLDA generic data structures and code out to shared
pcie-plda.h, pcie-plda-host.c (Minda Chen)
- Add PLDA generic interrupt handling with a .request_event_irq()
callback for vendor-specific events (Minda Chen)
- Add PLDA generic host init/deinit and map bus functions for use by
vendor-specific drivers (Minda Chen)
- Rework to use PLDA core (Minda Chen)
Microsoft Hyper-V host bridge driver:
- Return zero, not garbage, when reading PCI_INTERRUPT_PIN (Wei Liu)
NVIDIA Tegra194 PCIe controller driver:
- Remove unused struct tegra_pcie_soc (Dr. David Alan Gilbert)
- Set 64KB inbound ATU alignment restriction (Jon Hunter)
Qualcomm PCIe controller driver:
- Make the MHI reg region mandatory for X1E80100, since all PCIe
controllers have it (Abel Vesa)
- Prevent use of uninitialized data and possible error pointer
dereference (Dan Carpenter)
- Return error, not success, if dev_pm_opp_find_freq_floor() fails
(Dan Carpenter)
- Add Operating Performance Points (OPP) support to scale performance
state based on aggregate link bandwidth to improve SoC power
efficiency (Krishna chaitanya chundru)
- Vote for the CPU-PCIe ICC (interconnect) path to ensure it stays
active even if other drivers don't vote for it (Krishna chaitanya
chundru)
- Use devm_clk_bulk_get_all() to get all the clocks from DT to avoid
writing out all the clock names (Manivannan Sadhasivam)
- Add DT binding and driver support for the SA8775P SoC (Mrinmay
Sarkar)
- Add HDMA support for the SA8775P SoC (Mrinmay Sarkar)
- Override the SA8775P NO_SNOOP default to avoid possible memory
corruption (Mrinmay Sarkar)
- Make sure resources are disabled during PERST# assertion, even if
the link is already disabled (Manivannan Sadhasivam)
- Use new generic dw_pcie_ep_linkdown() to handle link-down events
(Manivannan Sadhasivam)
- Add DT and endpoint driver support for the SA8775P SoC (Mrinmay
Sarkar)
- Add Hyper DMA (HDMA) support for the SA8775P SoC and enable it in
the EPF MHI driver (Mrinmay Sarkar)
- Set PCIE_PARF_NO_SNOOP_OVERIDE to override the default NO_SNOOP
attribute on the SA8775P SoC (both Root Complex and Endpoint mode)
to avoid possible memory corruption (Mrinmay Sarkar)
Renesas R-Car PCIe controller driver:
- Demote WARN() to dev_warn_ratelimited() in rcar_pcie_wakeup() to
avoid unnecessary backtrace (Marek Vasut)
- Add DT and driver support for R-Car V4H (R8A779G0) host and
endpoint. This requires separate proprietary firmware (Yoshihiro
Shimoda)
Rockchip PCIe controller driver:
- Assert PERST# for 100ms after power is stable (Damien Le Moal)
- Wait PCIE_T_RRS_READY_MS (100ms) after reset before starting
configuration (Damien Le Moal)
- Use GPIOD_OUT_LOW flag while requesting ep_gpio to fix a firmware
crash on Qcom-based modems with Rockpro64 board (Manivannan
Sadhasivam)
Rockchip DesignWare PCIe controller driver:
- Factor common parts of rockchip-dw-pcie DT binding to be shared by
Root Complex and Endpoint mode (Niklas Cassel)
- Add missing INTx signals to common DT binding (Niklas Cassel)
- Add eDMA items to DT binding for Endpoint controller (Niklas
Cassel)
- Fix initial dw-rockchip PERST# GPIO value to prevent unnecessary
short assert/deassert that causes issues with some WLAN controllers
(Niklas Cassel)
- Refactor dw-rockchip and add support for Endpoint mode (Niklas
Cassel)
- Call pci_epc_init_notify() and drop dw_pcie_ep_init_notify()
wrapper (Niklas Cassel)
- Add error messages in .probe() error paths to improve user
experience (Uwe Kleine-König)
Samsung Exynos PCIe controller driver:
- Use bulk clock APIs to simplify clock setup (Shradha Todi)
StarFive PCIe controller driver:
- Add DT binding and driver support for the StarFive JH7110
PLDA-based PCIe controller (Minda Chen)
Synopsys DesignWare PCIe controller driver:
- Add generic support for sending PME_Turn_Off when system suspends
(Frank Li)
- Fix incorrect interpretation of iATU slot 0 after PERST#
assert/deassert (Frank Li)
- Use msleep() instead of usleep_range() while waiting for link
(Konrad Dybcio)
- Refactor dw_pcie_edma_find_chip() to enable adding support for
Hyper DMA (HDMA) (Manivannan Sadhasivam)
- Enable drivers to supply the eDMA channel count since some can't
auto detect this (Manivannan Sadhasivam)
- Call pci_epc_init_notify() and drop dw_pcie_ep_init_notify()
wrapper (Manivannan Sadhasivam)
- Pass the eDMA mapping format directly from drivers instead of
maintaining a capability for it (Manivannan Sadhasivam)
- Add generic dw_pcie_ep_linkdown() to notify EPF drivers about
link-down events and restore non-sticky DWC registers lost on link
down (Manivannan Sadhasivam)
- Add vendor-specific "apb" reg name, interrupt names, INTx names to
generic binding (Niklas Cassel)
- Enforce DWC restriction that 64-bit BARs must start with an
even-numbered BAR (Niklas Cassel)
- Consolidate args of dw_pcie_prog_outbound_atu() into a structure
(Yoshihiro Shimoda)
- Add support for endpoints to send Message TLPs, e.g., for INTx
emulation (Yoshihiro Shimoda)
TI DRA7xx PCIe controller driver:
- Rename .cpu_addr_fixup() parameter to reflect that it is a PCI
address, not a CPU address (Niklas Cassel)
TI Keystone PCIe controller driver:
- Validate IORESOURCE_BUS presence to avoid NULL pointer dereference
(Aleksandr Mishin)
- Work around AM65x/DRA80xM Errata #i2037 that corrupts TLPs and
causes processor hangs by limiting Max_Read_Request_Size (MRRS) and
Max_Payload_Size (MPS) (Kishon Vijay Abraham I)
- Leave BAR 0 disabled for AM654x to fix a regression caused by
6ab15b5e70 ("PCI: dwc: keystone: Convert .scan_bus() callback to
use add_bus"), which caused a 45-second boot delay (Siddharth
Vadapalli)
Xilinx Versal CPM PCIe controller driver:
- Fix overlapping bridge registers and 32-bit BAR addresses in DT
binding (Thippeswamy Havalige)
MicroSemi Switchtec management driver:
- Make struct switchtec_class constant (Greg Kroah-Hartman)
Miscellaneous:
- Remove unused struct acpi_handle_node (Dr. David Alan Gilbert)
- Add missing MODULE_DESCRIPTION() macros (Jeff Johnson)"
* tag 'pci-v6.11-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (154 commits)
PCI: loongson: Enable MSI in LS7A Root Complex
PCI: Extend ACS configurability
PCI: Add missing bridge lock to pci_bus_lock()
drm/vboxvideo: fix mapping leaks
PCI: Add managed pcim_iomap_range()
PCI: Remove legacy pcim_release()
PCI: Add managed pcim_intx()
PCI: vmd: Create domain symlink before pci_bus_add_devices()
PCI: qcom: Prevent use of uninitialized data in qcom_pcie_suspend_noirq()
PCI: qcom: Prevent potential error pointer dereference
PCI: qcom: Fix missing error code in qcom_pcie_probe()
PCI: Give pcim_set_mwi() its own devres cleanup callback
PCI: Move struct pci_devres.pinned bit to struct pci_dev
PCI: Remove struct pci_devres.enabled status bit
PCI: Document hybrid devres hazards
PCI: Add managed pcim_request_region()
PCI: Deprecate pcim_iomap_table(), pcim_iomap_regions_request_all()
PCI: Add managed partial-BAR request and map infrastructure
PCI: Add devres helpers for iomap table
PCI: Add and use devres helper for bit masks
...
Here is the big set of USB and Thunderbolt changes for 6.11-rc1.
Nothing earth-shattering in here, just constant forward progress in
adding support for new hardware and better debugging functionalities for
thunderbolt devices and the subsystem. Included in here are:
- thunderbolt debugging update and driver additions
- xhci driver updates
- typec driver updates
- kselftest device driver changes (acked by the relevant maintainers,
depended on other changes in this tree.)
- cdns3 driver updates
- gadget driver updates
- MODULE_DESCRIPTION() additions
- dwc3 driver updates and fixes
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZppaNA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylXZwCgrEtIAQw0x6EF7w/iTWVS5UJj9AEAoLCj5UwO
WX978uThyUctuYYKbw+8
=Cm7j
-----END PGP SIGNATURE-----
Merge tag 'usb-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt changes for 6.11-rc1.
Nothing earth-shattering in here, just constant forward progress in
adding support for new hardware and better debugging functionalities
for thunderbolt devices and the subsystem. Included in here are:
- thunderbolt debugging update and driver additions
- xhci driver updates
- typec driver updates
- kselftest device driver changes (acked by the relevant maintainers,
depended on other changes in this tree.)
- cdns3 driver updates
- gadget driver updates
- MODULE_DESCRIPTION() additions
- dwc3 driver updates and fixes
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (112 commits)
kselftest: devices: Add test to detect device error logs
kselftest: Move ksft helper module to common directory
kselftest: devices: Move discoverable devices test to subdirectory
usb: gadget: f_uac2: fix non-newline-terminated function name
USB: uas: Implement the new shutdown callback
USB: core: add 'shutdown' callback to usb_driver
usb: typec: Drop explicit initialization of struct i2c_device_id::driver_data to 0
usb: dwc3: enable CCI support for AMD-xilinx DWC3 controller
usb: dwc2: add support for other Lantiq SoCs
usb: gadget: Use u16 types for 16-bit fields
usb: gadget: midi2: Fix incorrect default MIDI2 protocol setup
usb: dwc3: core: Check all ports when set phy suspend
usb: typec: tcpci: add support to set connector orientation
dt-bindings: usb: Convert fsl-usb to yaml
usb: typec: ucsi: reorder operations in ucsi_run_command()
usb: typec: ucsi: extract common code for command handling
usb: typec: ucsi: inline ucsi_read_message_in
usb: typec: ucsi: rework command execution functions
usb: typec: ucsi: split read operation
usb: typec: ucsi: simplify command sending API
...
Here's a fix for a long-standing issue in the mos7840 driver that can trigger
a crash when resuming from system suspend.
Included are also some new modem device ids.
All have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCZo6w6gAKCRALxc3C7H1l
CNPAAP0SiU/4HcMRJ/m6Q2xPiuq27Xo6yFg7kjjRiCQVObio6AEA8wjAdSiMoPhx
p9vfS+8cvZ7z5YtxkBYPKaZsjESq+QM=
=cW58
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-6.10-rc8' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 6.10-rc8
Here's a fix for a long-standing issue in the mos7840 driver that can trigger
a crash when resuming from system suspend.
Included are also some new modem device ids.
All have been in linux-next with no reported issues.
* tag 'usb-serial-6.10-rc8' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: mos7840: fix crash on resume
USB: serial: option: add Rolling RW350-GL variants
USB: serial: option: add support for Foxconn T99W651
USB: serial: option: add Netprisma LCUK54 series modules
Most writes to configfs handle an optional newline, but do not require
it. By using the number of bytes written as the limit for scnprintf()
it is guaranteed that the final character in the buffer will be
overwritten.
This is expected if it is a newline but is undesirable when a string is
written "as-is" (as libusbgx does, for example).
Update the store function to strip an optional newline, matching the
behaviour of usb_string_copy().
Signed-off-by: John Keeping <jkeeping@inmusicbrands.com>
Link: https://lore.kernel.org/r/20240708142553.3995022-1-jkeeping@inmusicbrands.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A standard implementation of shutdown callback has been implemented
for USB drivers. Since the UAS driver implements a shutdown callback
this patch enables it to use the new standard implementation.
Signed-off-by: Kerem Karabay <kekrby@gmail.com>
Signed-off-by: Aditya Garg <gargaditya08@live.com>
Link: https://lore.kernel.org/r/E3A502A9-6572-4F1B-9EB2-2F6F0C4E6EA8@live.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently there is no standardized method for USB drivers to handle
shutdown events. This patch simplifies running code on shutdown for USB
devices by adding a shutdown callback to usb_driver.
Signed-off-by: Kerem Karabay <kekrby@gmail.com>
Signed-off-by: Aditya Garg <gargaditya08@live.com>
Link: https://lore.kernel.org/r/7AAC1BF4-8B60-448D-A3C1-B7E80330BE42@live.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These driver don't use the driver_data member of struct i2c_device_id,
so don't explicitly initialize this member.
This prepares putting driver_data in an anonymous union which requires
either no initialization or named designators. But it's also a nice
cleanup on its own.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20240710073050.192806-2-u.kleine-koenig@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The GSBUSCFG0 register bits [31:16] are used to configure the cache type
settings of the descriptor and data write/read transfers (Cacheable,
Bufferable/Posted). When CCI is enabled in the design, DWC3 core GSBUSCFG0
cache bits must be updated to support CCI enabled transfers in USB.
To program GSBUSCFG0 cache bits create a software node property
in AMD-xilinx dwc3 glue driver and pass it to dwc3 core. The core
then reads this property value and configures it in dwc3_core_init()
sequence.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/1720548651-726412-1-git-send-email-radhey.shyam.pandey@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The size of the internal RAM of the DesignWare USB controller changed
between the different Lantiq SoCs. We have the following sizes:
Amazon + Danube: 8 KByte
Amazon SE + arx100: 2 KByte
xrx200 + xrx300: 2.5 KByte
For Danube SoC we do not provide the params and let the driver decide
to use sane defaults, for the Amazon SE and arx100 we use small fifos
and for the xrx200 and xrx300 SCs a little bit bigger periodic fifo.
The auto detection of max_transfer_size and max_packet_count should
work, so remove it.
This patch is included in OpenWrt for many years.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Link: https://lore.kernel.org/r/20240708222054.2727789-1-hauke@hauke-m.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MIDI2 gadget driver handled the default MIDI protocol version
incorrectly due to the confusion of the protocol version passed via
configfs (either 1 or 2) and UMP protocol bits (0x100 / 0x200).
As a consequence, the default protocol always resulted in MIDI1.
This patch addresses the misunderstanding of the protocol handling.
Fixes: 29ee7a4ddd ("usb: gadget: midi2: Add configfs support")
Cc: stable <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20240708095719.25627-1-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit c49cfa9170 ("USB: serial: use generic method if no
alternative is provided in usb serial layer"), USB serial core calls the
generic resume implementation when the driver has not provided one.
This can trigger a crash on resume with mos7840 since support for
multiple read URBs was added back in 2011. Specifically, both port read
URBs are now submitted on resume for open ports, but the context pointer
of the second URB is left set to the core rather than mos7840 port
structure.
Fix this by implementing dedicated suspend and resume functions for
mos7840.
Tested with Delock 87414 USB 2.0 to 4x serial adapter.
Signed-off-by: Dmitry Smirnov <d.smirnov@inbox.lv>
[ johan: analyse crash and rewrite commit message; set busy flag on
resume; drop bulk-in check; drop unnecessary usb_kill_urb() ]
Fixes: d83b405383 ("USB: serial: add support for multiple read urbs")
Cc: stable@vger.kernel.org # 3.3
Signed-off-by: Johan Hovold <johan@kernel.org>
Use the struct_size macro to calculate the size of the pkt, which
includes a trailing flexible array.
Suggested-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <kees@kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Use the __counted_by compiler attribute for the data[] flexible array
member to improve the results of array bound sanitizers.
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <kees@kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Since commit 1fffe7a34c ("script: modpost: emit a warning when the
description is missing"), ARCH=x86 make allmodconfig && make W=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/serial/ch341.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/serial/usb_debug.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/serial/mxuport.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/serial/navman.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/serial/qcaux.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/serial/usb-serial-simple.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/serial/symbolserial.o
Add the missing invocations of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
[ johan: amend commit message with commit introducing W=1 warning;
tweak some descriptions ]
Signed-off-by: Johan Hovold <johan@kernel.org>
'spcp8x5_usb_ctrl_arg' has been unused since the original
commit 619a6f1d14 ("USB: add usb-serial spcp8x5 driver").
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Userspace provided string 's' could trivially have the length zero. Left
unchecked this will firstly result in an OOB read in the form
`if (str[0 - 1] == '\n') followed closely by an OOB write in the form
`str[0 - 1] = '\0'`.
There is already a validating check to catch strings that are too long.
Let's supply an additional check for invalid strings that are too short.
Signed-off-by: Lee Jones <lee@kernel.org>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20240705074339.633717-1-lee@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dwc3_enable_susphy() applies to all available ports. After the
introduction of multi-port in dwc3, we now know the number of ports. Go
through the phy suspend registers of each port to enable/disable phy
suspend in dwc3_enable_susphy().
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/31e18192c607dff0a7e5ca139dd5737d2224122a.1719879346.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Streamline control stream of ucsi_run_command(). Reorder operations so
that there is only one call to ucsi_acknowledge(), making sure that all
complete commands are acknowledged. This also makes sure that the
command is acknowledged even if reading MESSAGE_IN data returns an
error.
Tested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240627-ucsi-rework-interface-v4-7-289ddc6874c7@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Extract common functions to handle command sending and to handle events
from UCSI. This ensures that all UCSI glue drivers handle the ACKs in
the same way.
The CCG driver used DEV_CMD_PENDING both for internal
firmware-related commands and for UCSI control handling. Leave the
former use case intact.
Tested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240627-ucsi-rework-interface-v4-6-289ddc6874c7@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to have a separate wrapper for reading MESSAGE_IN data,
inline it to ucsi_run_command().
Tested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240627-ucsi-rework-interface-v4-5-289ddc6874c7@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rework command execution code to remove recursive calls of
ucsi_exec_command. This also streamlines the sync_control / read(CCI)
read (MESSAGE_IN) sequence, allowing further rework of the command code.
Tested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240627-ucsi-rework-interface-v4-4-289ddc6874c7@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The read operation is only used to read fixed data at fixed offsets
(UCSI_VERSION, UCSI_CCI, UCSI_MESSAGE_IN). In some cases drivers apply
offset-specific overrides. Split the read() operation into three
operations, read_version(), read_cci(), read_message_in().
Tested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240627-ucsi-rework-interface-v4-3-289ddc6874c7@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sync_write and async_write are used only for writing UCSI commands
to the UCSI_CONTROL offsets. Rename sync_write and async_write
operations to sync_control and async_control accordingly. Drop the
offset and length fields and pass u64 command instead.
Tested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240627-ucsi-rework-interface-v4-2-289ddc6874c7@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As a preparation for reworking UCSI command handling, move
ucsi_acknowledge() for the failed command from ucsi_read_error() to
ucsi_exec_command().
Tested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240627-ucsi-rework-interface-v4-1-289ddc6874c7@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The for_each_child_of_node() macro requires an explicit call to
of_node_put() on early exits to decrement the child refcount and avoid a
memory leak.
The child node is not required outsie the loop, and the resource must be
released before the function returns.
Add the missing of_node_put().
Cc: stable@vger.kernel.org
Fixes: 82e82130a7 ("usb: core: Set connect_type of ports based on DT node")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20240624-usb_core_of_memleak-v1-1-af6821c1a584@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
START BP-850K is a dot matrix printer that crashes when
it receives a Set-Interface request and needs USB_QUIRK_NO_SET_INTF
to work properly.
Cc: stable <stable@kernel.org>
Signed-off-by: jinxiaobo <jinxiaobo@uniontech.com>
Signed-off-by: WangYuli <wangyuli@uniontech.com>
Link: https://lore.kernel.org/r/202E4B2BD0F0FEA4+20240702154408.631201-1-wangyuli@uniontech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Syzbot has identified a bug in usbcore (see the Closes: tag below)
caused by our assumption that the reserved bits in an endpoint
descriptor's bEndpointAddress field will always be 0. As a result of
the bug, the endpoint_is_duplicate() routine in config.c (and possibly
other routines as well) may believe that two descriptors are for
distinct endpoints, even though they have the same direction and
endpoint number. This can lead to confusion, including the bug
identified by syzbot (two descriptors with matching endpoint numbers
and directions, where one was interrupt and the other was bulk).
To fix the bug, we will clear the reserved bits in bEndpointAddress
when we parse the descriptor. (Note that both the USB-2.0 and USB-3.1
specs say these bits are "Reserved, reset to zero".) This requires us
to make a copy of the descriptor earlier in usb_parse_endpoint() and
use the copy instead of the original when checking for duplicates.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+8693a0bb9c10b554272a@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/linux-usb/0000000000003d868e061bc0f554@google.com/
Fixes: 0a8fd13462 ("USB: fix problems with duplicate endpoint addresses")
CC: Oliver Neukum <oneukum@suse.com>
CC: stable@vger.kernel.org
Link: https://lore.kernel.org/r/205a5edc-7fef-4159-b64a-80374b6b101a@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Usb device connect may not be detected after runtime resume if
xHC is reset during resume.
In runtime resume cases xhci_resume() will only resume roothubs if there
are pending port events. If the xHC host is reset during runtime resume
due to a Save/Restore Error (SRE) then these pending port events won't be
detected as PORTSC change bits are not immediately set by host after reset.
Unconditionally resume roothubs if xHC is reset during resume to ensure
device connections are detected.
Also return early with error code if starting xHC fails after reset.
Issue was debugged and a similar solution suggested by Remi Pommarel.
Using this instead as it simplifies future refactoring.
Reported-by: Remi Pommarel <repk@triplefau.lt>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218987
Suggested-by: Remi Pommarel <repk@triplefau.lt>
Tested-by: Remi Pommarel <repk@triplefau.lt>
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240627145523.1453155-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some new modem device ids.
All have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCZn6FZwAKCRALxc3C7H1l
CGXqAP0W1xKjnpYr7NYD4wgMIwkJhfwFVSOIfpF2cqQJOr8CYAEAtEehPaGNerQx
Mg+nRudm8FllqvQlSUn3fqEdUkke+wg=
=Dxds
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-6.10-rc6' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial device ids for 6.10-rc6
Here are some new modem device ids.
All have been in linux-next with no reported issues.
* tag 'usb-serial-6.10-rc6' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add Telit generic core-dump composition
USB: serial: option: add Fibocom FM350-GL
USB: serial: option: add Telit FN912 rmnet compositions
In the match() callback, the struct device_driver * should not be
changed, so change the function callback to be a const *. This is one
step of many towards making the driver core safe to have struct
device_driver in read-only memory.
Because the match() callback is in all busses, all busses are modified
to handle this properly. This does entail switching some container_of()
calls to container_of_const() to properly handle the constant *.
For some busses, like PCI and USB and HV, the const * is cast away in
the match callback as those busses do want to modify those structures at
this point in time (they have a local lock in the driver structure.)
That will have to be changed in the future if they wish to have their
struct device * in read-only-memory.
Cc: Rafael J. Wysocki <rafael@kernel.org>
Reviewed-by: Alex Elder <elder@kernel.org>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Link: https://lore.kernel.org/r/2024070136-wrongdoer-busily-01e8@gregkh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are a handful of small USB driver fixes for 6.10-rc6 to resolve
some reported issues. Included in here are:
- typec driver bugfixes
- usb gadget driver reverts for commits that were reported to have
problems
- resource leak bugfix
- gadget driver bugfixes
- dwc3 driver bugfixes
- usb atm driver bugfix for when syzbot got loose on it
All of these have been in linux-next this week with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZoFnUA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ym3ggCgyM2B+cIOH4FtyWi7FfXj8XjDsjIAoKzX45+o
TO/pSGQhRwx9PeFfDISM
=pFEO
-----END PGP SIGNATURE-----
Merge tag 'usb-6.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a handful of small USB driver fixes for 6.10-rc6 to resolve
some reported issues. Included in here are:
- typec driver bugfixes
- usb gadget driver reverts for commits that were reported to have
problems
- resource leak bugfix
- gadget driver bugfixes
- dwc3 driver bugfixes
- usb atm driver bugfix for when syzbot got loose on it
All of these have been in linux-next this week with no reported issues"
* tag 'usb-6.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: dwc3: core: Workaround for CSR read timeout
Revert "usb: gadget: u_ether: Replace netif_stop_queue with netif_device_detach"
Revert "usb: gadget: u_ether: Re-attach netif device to mirror detachment"
usb: gadget: aspeed_udc: fix device address configuration
usb: dwc3: core: remove lock of otg mode during gadget suspend/resume to avoid deadlock
usb: typec: ucsi: glink: fix child node release in probe function
usb: musb: da8xx: fix a resource leak in probe()
usb: typec: ucsi_acpi: Add LG Gram quirk
usb: ucsi: stm32: fix command completion handling
usb: atm: cxacru: fix endpoint checking in cxacru_bind()
usb: gadget: printer: fix races against disable
usb: gadget: printer: SS+ support
This is a workaround for STAR 4846132, which only affects
DWC_usb31 version2.00a operating in host mode.
There is a problem in DWC_usb31 version 2.00a operating
in host mode that would cause a CSR read timeout When CSR
read coincides with RAM Clock Gating Entry. By disable
Clock Gating, sacrificing power consumption for normal
operation.
Cc: stable <stable@kernel.org> # 5.10.x: 1e43c86d: usb: dwc3: core: Add DWC31 version 2.00a controller
Signed-off-by: Jos Wang <joswang@lenovo.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240619114529.3441-1-joswang1221@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit f49449fbc2.
This commit breaks u_ether on some setups (at least Merrifield). The fix
"usb: gadget: u_ether: Re-attach netif device to mirror detachment" party
restores u-ether. However the netif usb: remains up even usb is switched
from device to host mode. This creates problems for user space as the
interface remains in the routing table while not realy present and network
managers (connman) not detecting a network change.
Various attempts to find the root cause were unsuccesful up to now. Therefore
revert until a solution is found.
Link: https://lore.kernel.org/linux-usb/20231006141231.7220-1-hgajjar@de.adit-jv.com/
Reported-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Reported-by: Ferry Toth <fntoth@gmail.com>
Fixes: f49449fbc2 ("usb: gadget: u_ether: Replace netif_stop_queue with netif_device_detach")
Cc: stable@vger.kernel.org
Signed-off-by: Ferry Toth <fntoth@gmail.com>
Link: https://lore.kernel.org/r/20240620204832.24518-3-ftoth@exalondelft.nl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for UCSI 2.0 Get Error Status command to add connector
number field to the command structure.
Connector number field is extracted from the previous UCSI command
which has failed and is used to get the failure reason/Error using
Get Error Status command.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Pooja Katiyar <pooja.katiyar@intel.com>
Link: https://lore.kernel.org/r/20240624213359.1270018-1-pooja.katiyar@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for UCSI 2.0 Get Error Status data structure changes
to add more error codes to the data structure.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Pooja Katiyar <pooja.katiyar@intel.com>
Link: https://lore.kernel.org/r/20240626185853.2956700-1-pooja.katiyar@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the setting of the plug's number of alternate modes into the
same condition as the plug's registration to prevent dereferencing the
connector's plug pointer while it is null.
Fixes: c313a44ac9 ("usb: typec: ucsi: Always set number of alternate modes")
Suggested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Jameson Thies <jthies@google.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20240625004607.3223757-1-jthies@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci macros that read and write endpoint ID bitfields of TRBs are mixing
the 1-based Endpoint ID as described in the xHCI specification, and
0-based endpoint index used by driver as an array index.
Sort this out by naming macros that deal with 1 based Endpoint ID fields
to *_EP_ID_*, and 0 based endpoint index values to *_EP_INDEX_*.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240626124835.1023046-22-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TGL systems have the same issue as ADL, where a large boot firmware
delay is seen if USB ports are left in U3 at shutdown. So apply the
XHCI_RESET_TO_DEFAULT quirk to TGL as well.
The issue it fixes is a ~20s boot time delay when booting from S5. It
affects TGL devices, and TGL support was added starting from v5.3.
Cc: stable@vger.kernel.org
Signed-off-by: Reka Norman <rekanorman@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240626124835.1023046-21-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add 'goto' statement for a halted endpoint, streamlining the error
handling process. In future handle_tx_event() changes this 'goto'
statement will have more uses.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240626124835.1023046-20-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This part is and should only performed once, so it's moved out of the
while loop to improve code readability.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240626124835.1023046-19-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a buggy HW reports some unpredicted event (for example, an overrun event
following a MSE event while the EP ring is actually not empty), the driver
will never find the TD, and it will loop until the TD list is empty.
Before commits [1][2], the spin lock was released when giving back a URB in
the do-while loop. This could cause more TD to be added to TD list, causing
an infinite loop.
Because of commits [1][2] the spin lock is not released any more, thus the
infinite loop prevention is unnecessary and is removed.
[1], commit 0c03d89d0c ("xhci: Giveback urb in finish_td directly")
[2], commit 36dc01657b ("usb: host: xhci: Support running urb giveback in
tasklet context")
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240626124835.1023046-18-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function doesn't releases and re-acquires the lock, this was removed
in commit 36dc01657b ("usb: host: xhci: Support running urb giveback in
tasklet context")
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240626124835.1023046-17-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Missed service event tells the driver that the hardware wasn't able to
process some queued isoc TDs in their right time slots, and some TDs will
be skipped. The driver sets a 'skip' flag to indicate that the next
transfer event after this event will point to some future TD instead of
the next queued TD. Once the driver receives the next event, it will skip
and give back all those hardware skipped TDs.
However, should this subsequent event be a stop endpoint which does not
point to the next pending TD, the driver fails to return the skipped TDs.
Instead, it loops for a period before outputting an erroneous message.
Fix this by repositioning the 'stop endpoint' check to follow the isoc
skip check, ensuring the skipped TDs are properly returned.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240626124835.1023046-16-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When xhci_requires_manual_halt_cleanup() was written it wasn't clear
that the xhci internal endpoint halt state always needs to be cleared
with a reset endpoint command. Functional stall cases additionally halt
the device side endpoint which requires class driver to clear the device
side halt with a CLEAR_FEATURE(ENDPOINT_HALT) request as well.
Clean up, rename, and make sure the new function always return true
when internal endpoint state is halted, including stall cases.
Based on related cleanup suggestion code by Niklas Neronin
cc: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240626124835.1023046-15-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove debug messages that served as sanity checks during the initial
implementation phase of underrun/overrun completion codes. These checks
are now unnecessary.
Instead, improve the default debug messages for underrun/overrun events,
so that they are consistent with the reset of the completion codes.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240626124835.1023046-14-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Improve error message for unknown transfer event without a TRB, by also
printing the event code number. This removes the inevitable question;
"what was the unknown event code exactly?"
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240626124835.1023046-13-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move handling transfer events without a target transfer TRB into
handle_transferless_tx_event(), this type of event does not utilize the
rest of handle_tx_event() and as a result it's better to separate it
into a dedicated function.
Additionally, this change reduces handle_tx_event()'s size and makes it
more readable.
[Mathias: Simplify code to return helper function value directly. This
removes the second xhci_err() message for untargeted and unexpected
event completion types]
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240626124835.1023046-12-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a preparation patch for switching from custom segment list
handling to using list.h functions.
Contain all segment re-numbering in xhci_link_rings() which links two
segments lists together, and performs all necessary adjustments for
them to fit together.
No need to send segment number to xhci_alloc_segments_for_ring()
as a parameter after this.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240626124835.1023046-11-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Older 0.95 xHCI hosts and some other specific newer hosts require the
chain bit to be set for Link TRBs even if the link TRB is not in the
middle of a transfer descriptor (TD).
move the checks for all those cases into one xhci_link_chain_quirk()
function to clean up and avoid code duplication.
No functional changes.
[skip renaming chain_links flag, reword commit message -Mathias]
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240626124835.1023046-10-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Argument struct 'xhci_interrupter *ir' is not used, and as a consequence
is removed.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240626124835.1023046-9-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Argument u32 'cmd_comp_code' is not used, and as a consequence
is removed.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240626124835.1023046-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove argument 'struct xhci_hcd *xhci' from functions which do not
utilize it. This change contributes to a simpler codebase by avoiding
redundant arguments.
Functions which have the argument removed:
check_interval()
xhci_num_trbs_free()
xhci_handle_cmd_enable_slot()
xhci_clear_interrupt_pending()
xhci_requires_manual_halt_cleanup()
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240626124835.1023046-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove 'num_trbs' from 'xhci_td' as it's no longer used following the
removal of 'num_trbs_free' tracking in commit 2710f8186f ("xhci: Stop
unnecessary tracking of free trbs in a ring").
Tracking of 'num_trbs_free' is still performed in xhci DbC, but it does not
utilize 'num_trbs'.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240626124835.1023046-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci DbC driver polls the host controller for DbC events at a reduced
rate when DbC is enabled but there are no active data transfers.
Allow users to modify this reduced poll interval via dbc_poll_interval_ms
sysfs entry. Unit is milliseconds and accepted range is 0 to 5000.
Max interval of 5000 ms is selected as it matches the common 5 second
timeout used in usb stack.
Default value is 64 milliseconds.
A long interval is useful when users know there won't be any activity
on systems connected via DbC for long periods, and want to avoid
battery drainage due to unnecessary CPU usage.
Example being Android Debugger (ADB) usage over DbC on ChromeOS systems
running Android Runtime.
[minor changes and rewording -Mathias]
Co-developed-by: Samuel Jacob <samjaco@google.com>
Signed-off-by: Samuel Jacob <samjaco@google.com>
Signed-off-by: Uday M Bhat <uday.m.bhat@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240626124835.1023046-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The transferred length is incorrectly zeroed for cancelled isoc
transfer TDs when the transfer ring stops on a cancelled TD with
a 'Stop - Length Invalid' completion code.
Length was always set to zero in these cases even if it should be
set to the sum of the TRB transfer block lengths up to
the TRB the ring stopped on, _excluding_ the one stopped on.
No issues reported due to this isoc case. Found while inspecting
related case in bulk transfer 'Stop - Length Invalid' handling.
Change this so that 'Stop - Length Invalid' transfer completion
cases always sum up TRB lengths instead of report a zero length.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240626124835.1023046-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
parsing xhci traces on systems with several xHCI controllers and connected
usb devices is difficult as entries are all interleaved.
showing usb devname in urb tracing reveals both which device, and which
bus/controller the entry is for.
old:
xhci_urb_enqueue: ep2in-bulk: urb 0000000039224498 ...
new:
xhci_urb_enqueue: 3-9.4 ep1in-bulk: urb 0000000013bf21e7 ...
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240626124835.1023046-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This codepath is trivially dead, since the function is never called with
a non-NULL td (the only callsite is immediately preceded by a NULL guard).
[remove unused label 'deq_found' -Mathias]
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240626124835.1023046-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should verify the bound of the array to assure that host
may not manipulate the index to point past endpoint array.
Found by static analysis.
Signed-off-by: Ma Ke <make24@iscas.ac.cn>
Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Acked-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Link: https://lore.kernel.org/r/20240625022306.2568122-1-make24@iscas.ac.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace SET_RUNTIME_PM_OPS() with its modern RUNTIME_PM_OPS()
alternative.
The combined usage of pm_ptr() and RUNTIME_PM_OPS allows the compiler
to evaluate if the runtime suspend/resume() functions are used at build
time or are simply dead code.
This allows removing the __maybe_unused notation from the runtime
suspend/resume() functions.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Link: https://lore.kernel.org/r/20240625231023.436403-2-festevam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace SET_RUNTIME_PM_OPS()/SET SYSTEM_SLEEP_PM_OPS() with their modern
RUNTIME_PM_OPS() and SYSTEM_SLEEP_PM_OPS() alternatives.
The combined usage of pm_ptr() and RUNTIME_PM_OPS/SYSTEM_SLEEP_PM_OPS()
allows the compiler to evaluate if the runtime suspend/resume() functions
are used at build time or are simply dead code.
This allows removing the __maybe_unused notation from the runtime
suspend/resume() functions.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Link: https://lore.kernel.org/r/20240625231023.436403-1-festevam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a match function for the onboard_usb_dev driver. Primary
matching is still done through the VID:PID pair, as usual for
USB devices. The new match function checks in addition whether
the device has a device tree node, which is a needed for using
the onboard_usb_dev driver.
Remove the check for a device tree node from _probe(), the new
match functions prevents devices without DT node from probing.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Tested-by: Jameson Thies <jthies@google.com>
Reviewed-by: Jameson Thies <jthies@google.com>
Link: https://lore.kernel.org/r/20240612180448.1.I805556c176c626872c15ce001f0e8198e1f95ae1@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set the host status byte when a data completion error is encountered
otherwise the upper layer may end up using the invalid zero'ed data.
The following output was observed from scsi/sd.c prior to this fix.
[ 11.872824] sd 0:0:0:1: [sdf] tag#9 data cmplt err -75 uas-tag 1 inflight:
[ 11.872826] sd 0:0:0:1: [sdf] tag#9 CDB: Read capacity(16) 9e 10 00 00 00 00 00 00 00 00 00 00 00 20 00 00
[ 11.872830] sd 0:0:0:1: [sdf] Sector size 0 reported, assuming 512.
Signed-off-by: Shantanu Goel <sgoel01@yahoo.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/87msnx4ec6.fsf@yahoo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Two fixes: one in the ufs driver fixing an obvious memory leak and the
other (with a core flag based update) trying to prevent USB crashes by
stopping the core from issuing a request for the I/O Hints mode page.
Signed-off-by: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCZnXk0iYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishXORAQCgNcf9
vxSCOJNDU+OJlBOZLAzylHJEAYRnK7MPNg7ucgD/b8D4ANGbbHz4gLIdC/1BPFwi
ZWmQwuClTmBJfCs6jSA=
=07Uv
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two fixes: one in the ufs driver fixing an obvious memory leak and the
other (with a core flag based update) trying to prevent USB crashes by
stopping the core from issuing a request for the I/O Hints mode page"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: usb: uas: Do not query the IO Advice Hints Grouping mode page for USB/UAS devices
scsi: core: Introduce the BLIST_SKIP_IO_HINTS flag
scsi: ufs: core: Free memory allocated for model before reinit
In the aspeed UDC setup, we configure the UDC hardware with the assigned
USB device address.
However, we have an off-by-one in the bitmask, so we're only setting the
lower 6 bits of the address (USB addresses being 7 bits, and the
hardware bitmask being bits 0:6).
This means that device enumeration fails if the assigned address is
greater than 64:
[ 344.607255] usb 1-1: new high-speed USB device number 63 using ehci-platform
[ 344.808459] usb 1-1: New USB device found, idVendor=cc00, idProduct=cc00, bcdDevice= 6.10
[ 344.817684] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 344.825671] usb 1-1: Product: Test device
[ 344.831075] usb 1-1: Manufacturer: Test vendor
[ 344.836335] usb 1-1: SerialNumber: 00
[ 349.917181] usb 1-1: USB disconnect, device number 63
[ 352.036775] usb 1-1: new high-speed USB device number 64 using ehci-platform
[ 352.249432] usb 1-1: device descriptor read/all, error -71
[ 352.696740] usb 1-1: new high-speed USB device number 65 using ehci-platform
[ 352.909431] usb 1-1: device descriptor read/all, error -71
Use the correct mask of 0x7f (rather than 0x3f), and generate this
through the GENMASK macro, so we have numbers that correspond exactly
to the hardware register definition.
Fixes: 055276c132 ("usb: gadget: add Aspeed ast2600 udc driver")
Cc: stable@vger.kernel.org
Reviewed-by: Neal Liu <neal_liu@aspeedtech.com>
Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://lore.kernel.org/r/20240613-aspeed-udc-v2-1-29501ce9cb7a@codeconstruct.com.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When config CONFIG_USB_DWC3_DUAL_ROLE is selected, and trigger system
to enter suspend status with below command:
echo mem > /sys/power/state
There will be a deadlock issue occurring. Detailed invoking path as
below:
dwc3_suspend_common()
spin_lock_irqsave(&dwc->lock, flags); <-- 1st
dwc3_gadget_suspend(dwc);
dwc3_gadget_soft_disconnect(dwc);
spin_lock_irqsave(&dwc->lock, flags); <-- 2nd
This issue is exposed by commit c7ebd8149e ("usb: dwc3: gadget: Fix
NULL pointer dereference in dwc3_gadget_suspend") that removes the code
of checking whether dwc->gadget_driver is NULL or not. It causes the
following code is executed and deadlock occurs when trying to get the
spinlock. In fact, the root cause is the commit 5265397f9442("usb: dwc3:
Remove DWC3 locking during gadget suspend/resume") that forgot to remove
the lock of otg mode. So, remove the redundant lock of otg mode during
gadget suspend/resume.
Fixes: 5265397f94 ("usb: dwc3: Remove DWC3 locking during gadget suspend/resume")
Cc: Xu Yang <xu.yang_2@nxp.com>
Cc: stable@vger.kernel.org
Signed-off-by: Meng Li <Meng.Li@windriver.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240618031918.2585799-1-Meng.Li@windriver.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The device_for_each_child_node() macro requires explicit calls to
fwnode_handle_put() in all early exits of the loop if the child node is
not required outside. Otherwise, the child node's refcount is not
decremented and the resource is not released.
The current implementation of pmic_glink_ucsi_probe() makes use of the
device_for_each_child_node(), but does not release the child node on
early returns. Add the missing calls to fwnode_handle_put().
Cc: stable@vger.kernel.org
Fixes: c6165ed2f4 ("usb: ucsi: glink: use the connector orientation GPIO to provide switch events")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240613-ucsi-glink-release-node-v1-1-f7629a56f70a@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some LG Gram laptops report a bogus connector change event after a
GET_PDOS command for the partner's source PDOs, which disappears from
the CCI after acknowledging the command. However, the subsequent
GET_CONNECTOR_STATUS in ucsi_handle_connector_change() still reports
this bogus change in bits 5 and 6, leading to the UCSI core re-checking
the partner's source PDOs and thus to an infinite loop.
Fix this by adding a quirk that signals when a potentially buggy GET_PDOS
command is used, checks the status change report and clears it if it is a
bogus event before sending it to the UCSI core.
Signed-off-by: Diogo Ivo <diogo.ivo@tecnico.ulisboa.pt>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240612-gram_quirk-v1-1-52b0ff0e1546@tecnico.ulisboa.pt
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sometimes errors are seen, when doing DR swap, like:
[ 24.672481] ucsi-stm32g0-i2c 0-0035: UCSI_GET_PDOS failed (-5)
[ 24.720188] ucsi-stm32g0-i2c 0-0035: ucsi_handle_connector_change:
GET_CONNECTOR_STATUS failed (-5)
There may be some race, which lead to read CCI, before the command complete
flag is set, hence returning -EIO. Similar fix has been done also in
ucsi_acpi [1].
In case of a spurious or otherwise delayed notification it is
possible that CCI still reports the previous completion. The
UCSI spec is aware of this and provides two completion bits in
CCI, one for normal commands and one for acks. As acks and commands
alternate the notification handler can determine if the completion
bit is from the current command.
To fix this add the ACK_PENDING bit for ucsi_stm32g0 and only complete
commands if the completion bit matches.
[1] https://lore.kernel.org/lkml/20240121204123.275441-3-lk@c--e.de/
Fixes: 72849d4fce ("usb: typec: ucsi: stm32g0: add support for stm32g0 controller")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/stable/20240612124656.2305603-1-fabrice.gasnier%40foss.st.com
Cc: stable <stable@kernel.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240612124656.2305603-1-fabrice.gasnier@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Syzbot is still reporting quite an old issue [1] that occurs due to
incomplete checking of present usb endpoints. As such, wrong
endpoints types may be used at urb sumbitting stage which in turn
triggers a warning in usb_submit_urb().
Fix the issue by verifying that required endpoint types are present
for both in and out endpoints, taking into account cmd endpoint type.
Unfortunately, this patch has not been tested on real hardware.
[1] Syzbot report:
usb 1-1: BOGUS urb xfer, pipe 1 != type 3
WARNING: CPU: 0 PID: 8667 at drivers/usb/core/urb.c:502 usb_submit_urb+0xed2/0x18a0 drivers/usb/core/urb.c:502
Modules linked in:
CPU: 0 PID: 8667 Comm: kworker/0:4 Not tainted 5.14.0-rc4-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: usb_hub_wq hub_event
RIP: 0010:usb_submit_urb+0xed2/0x18a0 drivers/usb/core/urb.c:502
...
Call Trace:
cxacru_cm+0x3c0/0x8e0 drivers/usb/atm/cxacru.c:649
cxacru_card_status+0x22/0xd0 drivers/usb/atm/cxacru.c:760
cxacru_bind+0x7ac/0x11a0 drivers/usb/atm/cxacru.c:1209
usbatm_usb_probe+0x321/0x1ae0 drivers/usb/atm/usbatm.c:1055
cxacru_usb_probe+0xdf/0x1e0 drivers/usb/atm/cxacru.c:1363
usb_probe_interface+0x315/0x7f0 drivers/usb/core/driver.c:396
call_driver_probe drivers/base/dd.c:517 [inline]
really_probe+0x23c/0xcd0 drivers/base/dd.c:595
__driver_probe_device+0x338/0x4d0 drivers/base/dd.c:747
driver_probe_device+0x4c/0x1a0 drivers/base/dd.c:777
__device_attach_driver+0x20b/0x2f0 drivers/base/dd.c:894
bus_for_each_drv+0x15f/0x1e0 drivers/base/bus.c:427
__device_attach+0x228/0x4a0 drivers/base/dd.c:965
bus_probe_device+0x1e4/0x290 drivers/base/bus.c:487
device_add+0xc2f/0x2180 drivers/base/core.c:3354
usb_set_configuration+0x113a/0x1910 drivers/usb/core/message.c:2170
usb_generic_driver_probe+0xba/0x100 drivers/usb/core/generic.c:238
usb_probe_device+0xd9/0x2c0 drivers/usb/core/driver.c:293
Reported-and-tested-by: syzbot+00c18ee8497dd3be6ade@syzkaller.appspotmail.com
Fixes: 902ffc3c70 ("USB: cxacru: Use a bulk/int URB to access the command endpoint")
Cc: stable <stable@kernel.org>
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Link: https://lore.kernel.org/r/20240609131546.3932-1-n.zhandarovich@fintech.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
printer_read() and printer_write() guard against the race
against disable() by checking the dev->interface flag,
which in turn is guarded by a spinlock.
These functions, however, drop the lock on multiple occasions.
This means that the test has to be redone after reacquiring
the lock and before doing IO.
Add the tests.
This also addresses CVE-2024-25741
Fixes: 7f2ca14d2f ("usb: gadget: function: printer: Interface is disabled and returns error")
Cc: stable <stable@kernel.org>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20240620114039.5767-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to treat super speed plus as super speed, not the default,
which is full speed.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20240620093800.28901-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the Type-C graph, the nb7vpq904m retimer is in between the USB-C
connector and the USB3/DP combo PHY, and this PHY also requires the
USB-C mode events to properly set-up the SuperSpeed Lanes functions
to setup USB3-only, USB3 + DP Altmode or DP Altmode only on the 4 lanes.
Update the nb7vpq904m retimer to get an optional type-c mux on the next
endpoint, and broadcast the received mode to it.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240606-topic-sm8x50-upstream-retimer-broadcast-mode-v2-4-c6f6eae479c3@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the Type-C graph, the ptn36502 retimer is in between the USB-C
connector and the USB3/DP combo PHY, and this PHY also requires the
USB-C mode events to properly set-up the SuperSpeed Lanes functions
to setup USB3-only, USB3 + DP Altmode or DP Altmode only on the 4 lanes.
Update the ptn36502 retimer to get an optional type-c mux on the next
endpoint, and broadcast the received mode to it.
Tested-by: Luca Weiss <luca.weiss@fairphone.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240606-topic-sm8x50-upstream-retimer-broadcast-mode-v2-3-c6f6eae479c3@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the missing call to typec_switch_put() when probe fails and
the nb7vpq904m_remove() call is called.
Fixes: 348359e7c2 ("usb: typec: nb7vpq904m: Add an error handling path in nb7vpq904m_probe()")
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Fixes: 88d8f3ac9c ("usb: typec: add support for the nb7vpq904m Type-C Linear Redriver")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240606-topic-sm8x50-upstream-retimer-broadcast-mode-v2-2-c6f6eae479c3@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the missing call to typec_switch_put() when probe fails and
the ptn36502_remove() call is called.
Fixes: 8e99dc7836 ("usb: typec: add support for PTN36502 redriver")
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240606-topic-sm8x50-upstream-retimer-broadcast-mode-v2-1-c6f6eae479c3@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adding support for the charge type Linux power supply class
property (POWER_SUPPLY_PROP_CHARGE_TYPE) to the UCSI driver.
That will make the charge type visible in the charge_type
power supply class sysfs attribute file.
UCSI has the charge type specified in the Battery Charging
Status field of the response to the GET_CONNECTOR_STATUS
command.
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240619140806.3502590-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On systems where the UCSI PDOs are not supported, the UCSI driver is
giving an error message. This can cause users to believe there is a HW
issue with their system when in fact it is working as designed.
Check if PDO_DETAILS are supported as a feature before attempting to
access PDO. If not supported return that zero PDOs are available.
Tested on Lenovo L14 G5 AMD and confirmed with Lenovo FW team that PDOs
are not supported on this platform.
Suggested-by: Diogo Ivo <diogo.ivo@siemens.com>
Suggested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240609214328.6580-1-mpearson-lenovo@squebb.ca
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xHCI specification 5.1 "Register Conventions" states that 64 bit
registers should be written in low-high order. All writing operations
in xhci is done low-high order following the spec.
Add a new quirk to support workaround for high-low order.
Signed-off-by: Daehwan Jung <dh10.jung@samsung.com>
Link: https://lore.kernel.org/r/1718019553-111939-4-git-send-email-dh10.jung@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This quirk is for the controller that has a limitation in supporting
separate ERSTBA_HI and ERSTBA_LO programming. It's supported when
the ERSTBA is programmed ERSTBA_HI before ERSTBA_LO. That's because
the internal initialization of event ring fetches the
"Event Ring Segment Table Entry" based on the indication of ERSTBA_LO
written.
Signed-off-by: Daehwan Jung <dh10.jung@samsung.com>
Link: https://lore.kernel.org/r/1718019553-111939-3-git-send-email-dh10.jung@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's the limitation of Synopsys dwc3 controller with ERST programming in
supporting separate ERSTBA_HI and ERSTBA_LO programming. It's supported when
the ERSTBA is programmed ERSTBA_HI before ERSTBA_LO. But, writing operations
in xHCI is done low-high order following xHCI spec. xHCI specification 5.1
"Register Conventions" states that 64 bit registers should be written in
low-high order. Synopsys dwc3 needs workaround for high-low order. That's why
adding new quirk is needed to support this.
Signed-off-by: Daehwan Jung <dh10.jung@samsung.com>
Link: https://lore.kernel.org/r/1718019553-111939-2-git-send-email-dh10.jung@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify the current firmware packet size check in the tps6598x
implementation by means of a single call to min(), which is what the
current code does in a more verbose, less elegant way.
This patch fixes a cocci warning ("WARNING opportunity for min()").
Suggested-by: Julia Lawall <julia.lawall@inria.fr>
Signed-off-by: Javier Carrasco <javier.carrasco@wolfvision.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240606-tps6598x_fw_update_log-v1-3-2b5b8369a0ba@wolfvision.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current error logs do not show the firmware name and size for the
tps6598x. On the other hand, this information is provided for the
tps25750. Both implementations have access to that information, and the
existing message for the tps25750 can be used for the tps6598x without
extra modifications.
Signed-off-by: Javier Carrasco <javier.carrasco@wolfvision.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240606-tps6598x_fw_update_log-v1-2-2b5b8369a0ba@wolfvision.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tps_request_firmware() reads the firmware name and there is no need to
repeat the action in the device-specific implementations of the firmware
update mechanism.
Provide the firmware name as a parameter in tps_request_firmware() to
avoid repetitive operations in the device-specific implementations.
Signed-off-by: Javier Carrasco <javier.carrasco@wolfvision.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240606-tps6598x_fw_update_log-v1-1-2b5b8369a0ba@wolfvision.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_for_completion_timeout() causing patterns like:
timeout = wait_for_completion_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240604212730.4968-2-wsa+renesas@sang-engineering.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These drivers don't use the driver_data member of struct i2c_device_id,
so don't explicitly initialize this member.
This prepares putting driver_data in an anonymous union which requires
either no initialization or named designators. But it's also a nice
cleanup on its own.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20240619194413.2544537-2-u.kleine-koenig@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With ARCH=x86, make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/core/usbcore.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/mon/usbmon.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/class/usbtmc.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/storage/uas.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/chipidea/ci_hdrc_msm.o
Add the missing invocations of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://lore.kernel.org/r/20240618-md-drivers-usb-v2-1-e9b20a5eb7f9@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With ARCH=x86, make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/common/usb-common.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/common/usb-otg-fsm.o
Add the missing invocations of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://lore.kernel.org/r/20240611-md-drivers-usb-common-v1-1-f81555b0bd0d@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With ARCH=x86, make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/phy/phy-am335x-control.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/phy/phy-am335x.o
Add the missing invocations of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://lore.kernel.org/r/20240611-md-drivers-usb-phy-v1-1-1cacb41280c3@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With ARCH=x86, make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/host/ohci-exynos.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/host/xhci-pci-renesas.o
Add the missing invocations of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://lore.kernel.org/r/20240611-md-drivers-usb-host-v1-1-e2071a696ef8@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With ARCH=x86, make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/misc/ezusb.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/misc/isight_firmware.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/usb/misc/yurex.o
Add the missing invocations of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://lore.kernel.org/r/20240611-md-drivers-usb-misc-v1-1-98475a5aa8ef@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmZvTbAeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGVksIAJEn4a9IVM8FNCJy
Dxo0BItD1/qJ5mLDptqUFRKlxInjbojofz5CyoeIeXb0DwRfB16ALXqNXAkd3APi
saoOpfjFsg2H2OqL9CHdkzWcJEAq2lDnL0zaOjumeDVu/EyeT+tC4e4hq1e6Bm0E
fPC5ms2b+07DF9Rg6/DW8yPbdM5n6Mz1bRd3fQOIgvpM3yGOyGztEBgTRub/ZUgH
5pNJauknFAZgdiWhgNpc+lPWYZbgHKULQPhUBPdVhDIXPtQNUlKgNTQc6+L0Nmbb
K1sG1q7FLeMJOTFGQfD4r26X5DNQUi894q/9SX8X7rcrECdJKcw2WjVyB4myADpf
ae2gP+A=
=XjWP
-----END PGP SIGNATURE-----
Merge tag 'v6.10-rc4' into usb-next
We need the USB / Thunderbolt fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The syzbot fuzzer found that the interrupt-URB completion callback in
the cdc-wdm driver was taking too long, and the driver's immediate
resubmission of interrupt URBs with -EPROTO status combined with the
dummy-hcd emulation to cause a CPU lockup:
cdc_wdm 1-1:1.0: nonzero urb status received: -71
cdc_wdm 1-1:1.0: wdm_int_callback - 0 bytes
watchdog: BUG: soft lockup - CPU#0 stuck for 26s! [syz-executor782:6625]
CPU#0 Utilization every 4s during lockup:
#1: 98% system, 0% softirq, 3% hardirq, 0% idle
#2: 98% system, 0% softirq, 3% hardirq, 0% idle
#3: 98% system, 0% softirq, 3% hardirq, 0% idle
#4: 98% system, 0% softirq, 3% hardirq, 0% idle
#5: 98% system, 1% softirq, 3% hardirq, 0% idle
Modules linked in:
irq event stamp: 73096
hardirqs last enabled at (73095): [<ffff80008037bc00>] console_emit_next_record kernel/printk/printk.c:2935 [inline]
hardirqs last enabled at (73095): [<ffff80008037bc00>] console_flush_all+0x650/0xb74 kernel/printk/printk.c:2994
hardirqs last disabled at (73096): [<ffff80008af10b00>] __el1_irq arch/arm64/kernel/entry-common.c:533 [inline]
hardirqs last disabled at (73096): [<ffff80008af10b00>] el1_interrupt+0x24/0x68 arch/arm64/kernel/entry-common.c:551
softirqs last enabled at (73048): [<ffff8000801ea530>] softirq_handle_end kernel/softirq.c:400 [inline]
softirqs last enabled at (73048): [<ffff8000801ea530>] handle_softirqs+0xa60/0xc34 kernel/softirq.c:582
softirqs last disabled at (73043): [<ffff800080020de8>] __do_softirq+0x14/0x20 kernel/softirq.c:588
CPU: 0 PID: 6625 Comm: syz-executor782 Tainted: G W 6.10.0-rc2-syzkaller-g8867bbd4a056 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 04/02/2024
Testing showed that the problem did not occur if the two error
messages -- the first two lines above -- were removed; apparently adding
material to the kernel log takes a surprisingly large amount of time.
In any case, the best approach for preventing these lockups and to
avoid spamming the log with thousands of error messages per second is
to ratelimit the two dev_err() calls. Therefore we replace them with
dev_err_ratelimited().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Suggested-by: Greg KH <gregkh@linuxfoundation.org>
Reported-and-tested-by: syzbot+5f996b83575ef4058638@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/linux-usb/00000000000073d54b061a6a1c65@google.com/
Reported-and-tested-by: syzbot+1b2abad17596ad03dcff@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/linux-usb/000000000000f45085061aa9b37e@google.com/
Fixes: 9908a32e94 ("USB: remove err() macro from usb class drivers")
Link: https://lore.kernel.org/linux-usb/40dfa45b-5f21-4eef-a8c1-51a2f320e267@rowland.harvard.edu/
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/29855215-52f5-4385-b058-91f42c2bee18@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When multiple streams are in use, multiple TDs might be in flight when
an endpoint is stopped. We need to issue a Set TR Dequeue Pointer for
each, to ensure everything is reset properly and the caches cleared.
Change the logic so that any N>1 TDs found active for different streams
are deferred until after the first one is processed, calling
xhci_invalidate_cancelled_tds() again from xhci_handle_cmd_set_deq() to
queue another command until we are done with all of them. Also change
the error/"should never happen" paths to ensure we at least clear any
affected TDs, even if we can't issue a command to clear the hardware
cache, and complain loudly with an xhci_warn() if this ever happens.
This problem case dates back to commit e9df17eb14 ("USB: xhci: Correct
assumptions about number of rings per endpoint.") early on in the XHCI
driver's life, when stream support was first added.
It was then identified but not fixed nor made into a warning in commit
674f8438c1 ("xhci: split handling halted endpoints into two steps"),
which added a FIXME comment for the problem case (without materially
changing the behavior as far as I can tell, though the new logic made
the problem more obvious).
Then later, in commit 94f339147f ("xhci: Fix failure to give back some
cached cancelled URBs."), it was acknowledged again.
[Mathias: commit 94f339147f ("xhci: Fix failure to give back some cached
cancelled URBs.") was a targeted regression fix to the previously mentioned
patch. Users reported issues with usb stuck after unmounting/disconnecting
UAS devices. This rolled back the TD clearing of multiple streams to its
original state.]
Apparently the commit author was aware of the problem (yet still chose
to submit it): It was still mentioned as a FIXME, an xhci_dbg() was
added to log the problem condition, and the remaining issue was mentioned
in the commit description. The choice of making the log type xhci_dbg()
for what is, at this point, a completely unhandled and known broken
condition is puzzling and unfortunate, as it guarantees that no actual
users would see the log in production, thereby making it nigh
undebuggable (indeed, even if you turn on DEBUG, the message doesn't
really hint at there being a problem at all).
It took me *months* of random xHC crashes to finally find a reliable
repro and be able to do a deep dive debug session, which could all have
been avoided had this unhandled, broken condition been actually reported
with a warning, as it should have been as a bug intentionally left in
unfixed (never mind that it shouldn't have been left in at all).
> Another fix to solve clearing the caches of all stream rings with
> cancelled TDs is needed, but not as urgent.
3 years after that statement and 14 years after the original bug was
introduced, I think it's finally time to fix it. And maybe next time
let's not leave bugs unfixed (that are actually worse than the original
bug), and let's actually get people to review kernel commits please.
Fixes xHC crashes and IOMMU faults with UAS devices when handling
errors/faults. Easiest repro is to use `hdparm` to mark an early sector
(e.g. 1024) on a disk as bad, then `cat /dev/sdX > /dev/null` in a loop.
At least in the case of JMicron controllers, the read errors end up
having to cancel two TDs (for two queued requests to different streams)
and the one that didn't get cleared properly ends up faulting the xHC
entirely when it tries to access DMA pages that have since been unmapped,
referred to by the stale TDs. This normally happens quickly (after two
or three loops). After this fix, I left the `cat` in a loop running
overnight and experienced no xHC failures, with all read errors
recovered properly. Repro'd and tested on an Apple M1 Mac Mini
(dwc3 host).
On systems without an IOMMU, this bug would instead silently corrupt
freed memory, making this a security bug (even on systems with IOMMUs
this could silently corrupt memory belonging to other USB devices on the
same controller, so it's still a security bug). Given that the kernel
autoprobes partition tables, I'm pretty sure a malicious USB device
pretending to be a UAS device and reporting an error with the right
timing could deliberately trigger a UAF and write to freed memory, with
no user action.
[Mathias: Commit message and code comment edit, original at:]
https://lore.kernel.org/linux-usb/20240524-xhci-streams-v1-1-6b1f13819bea@marcan.st/
Fixes: e9df17eb14 ("USB: xhci: Correct assumptions about number of rings per endpoint.")
Fixes: 94f339147f ("xhci: Fix failure to give back some cached cancelled URBs.")
Fixes: 674f8438c1 ("xhci: split handling halted endpoints into two steps")
Cc: stable@vger.kernel.org
Cc: security@kernel.org
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240611120610.3264502-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As described in commit 8f873c1ff4 ("xhci: Blacklist using streams on the
Etron EJ168 controller"), EJ188 have the same issue as EJ168, where Streams
do not work reliable on EJ188. So apply XHCI_BROKEN_STREAMS quirk to EJ188
as well.
Cc: stable@vger.kernel.org
Signed-off-by: Kuangyi Chiang <ki.chiang65@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240611120610.3264502-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As described in commit c877b3b2ad ("xhci: Add reset on resume quirk for
asrock p67 host"), EJ188 have the same issue as EJ168, where completely
dies on resume. So apply XHCI_RESET_ON_RESUME quirk to EJ188 as well.
Cc: stable@vger.kernel.org
Signed-off-by: Kuangyi Chiang <ki.chiang65@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240611120610.3264502-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The transferred length is set incorrectly for cancelled bulk
transfer TDs in case the bulk transfer ring stops on the last transfer
block with a 'Stop - Length Invalid' completion code.
length essentially ends up being set to the requested length:
urb->actual_length = urb->transfer_buffer_length
Length for 'Stop - Length Invalid' cases should be the sum of all
TRB transfer block lengths up to the one the ring stopped on,
_excluding_ the one stopped on.
Fix this by always summing up TRB lengths for 'Stop - Length Invalid'
bulk cases.
This issue was discovered by Alan Stern while debugging
https://bugzilla.kernel.org/show_bug.cgi?id=218890, but does not
solve that bug. Issue is older than 4.10 kernel but fix won't apply
to those due to major reworks in that area.
Tested-by: Pierre Tomon <pierretom+12@ik.me>
Cc: stable@vger.kernel.org # v4.10+
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240611120610.3264502-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While 'x' and '&x[0]' are equivalent, most of the PCI drivers use the
former form for the .id_table.
Update some drivers and documentation for consistency.
Link: https://lore.kernel.org/r/20240517120458.1260489-1-masahiroy@kernel.org
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
UCSI version 2.0 and above define new PPM notifications. Update the
logic to determine which notifications to enable taking into account
these changes.
Signed-off-by: Diogo Ivo <diogo.ivo@tecnico.ulisboa.pt>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240524105837.15342-3-diogo.ivo@tecnico.ulisboa.pt
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The enable gpio is not required when the SBU mux is used only for
orientation, make it optional.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240603083558.9629-3-francesco@dolcini.it
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Providing the number of known alternate modes allows user space to
determine when device registration has completed. Always register a
number of known alternate modes for the partner and cable plug, even
when the number of supported alternate modes is 0.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Jameson Thies <jthies@google.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240510201244.2968152-5-jthies@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Delay the ucsi_check_altmodes task to be inline with surrounding partner
tasks. This allows partner, cable and identity discovery to complete
before alternate mode registration. With that order, alternate mode
discovery can be used to indicate the ucsi driver has completed
discovery.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Jameson Thies <jthies@google.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240510201244.2968152-4-jthies@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When adding altmode ops, update the sysfs group so that visibility is
also recalculated.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Jameson Thies <jthies@google.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240510201244.2968152-3-jthies@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ucsi_register_altmode checks IS_ERR for the alt pointer and treats
NULL as valid. When CONFIG_TYPEC_DP_ALTMODE is not enabled,
ucsi_register_displayport returns NULL which causes a NULL pointer
dereference in trace. Rather than return NULL, call
typec_port_register_altmode to register DisplayPort alternate mode
as a non-controllable mode when CONFIG_TYPEC_DP_ALTMODE is not enabled.
Reviewed-by: Benson Leung <bleung@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Jameson Thies <jthies@google.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240510201244.2968152-2-jthies@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no specific behaviour implemented to recover from a babble
error. When a BABBLE error happens, recovery fails as connected sticks
are no longer detected by the USB controller.
Implement the recover callback of the MUSB operation to reset the USB
controller when a BABBLE happens.
Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com>
Link: https://lore.kernel.org/r/20240528102026.40136-5-bastien.curutchet@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The idle_state is not meant for host-only mode. When the device acts as a
host, it fails to exit the idle state once entered. This prevents new
USB gadgets from being detected once plugged in.
Commit 032ec49f53 ("usb: musb: drop useless board_mode usage") removed
a is_otg_enabled() check in the try_idle() that prevented from entering
idle_state. This was removed because at that time it was not possible to
select host-only mode with CONFIG_USB_MUSB_HOST so dual role was always
set.
Add #ifndef CONFIG_USB_MUSB_HOST around try_idle() callback to prevent
from entering idle_state when host-only mode has been selected.
Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com>
Link: https://lore.kernel.org/r/20240528102026.40136-4-bastien.curutchet@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 7ccf62941a.
da8xx_musb_set_mode() forces OTG mode regardless the selected mode even
if the property 'dr_mode = "host"' is present in device-tree. This
causes an unrecoverable error when VBUS supply is shut down : plugged
gadgets are no longer detected once VBUS supply is back.
Reverting it allows to have a selected mode coherent with device-tree's
description. IMO, this shouldn't cause regression because OTG mode is
the default selection when 'dr_mode' property is not set.
Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com>
Link: https://lore.kernel.org/r/20240528102026.40136-3-bastien.curutchet@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A USB-C hard reset involves removing the voltage from VBUS for some
time. So basically it has the same effect as removing the USB-C plug
for a short moment. If the machine is powered from the USB-C port and
does not have a fallback supply (e.g. a battery), this will result in
a full machine reset due to power loss.
Ideally we want to avoid triggering a hard reset on these boards. A
non-working USB-C port is probably better than unplanned reboots. But
boards with a backup supply should do the hard reset to get everything
working again.
In theory it would be enough to check the self_powered property, but
it seems the property might not be configured consistently enough in
system firmwares.
So let's start with just printing an error message when a hard reset is
triggered on systems we expect to be affected. This at least makes
debugging issues on affected systems easier without impacting unaffected
systems too much.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240523171645.223225-1-sebastian.reichel@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the Linux Type-C controller drivers probe, they requests a soft
reset, which should result in the source restarting to send Source
Capability messages again independently of the previous state.
Unfortunately some USB PD sources do not follow the specification and
do not send them after a soft reset when they already negotiated a
specific contract before. The current way (and what is described in the
specificiation) to resolve this problem is triggering a hard reset.
But a hard reset is fatal on batteryless platforms powered via USB-C PD,
since that removes VBUS for some time. Since this is triggered at boot
time, the system will be stuck in a boot loop. Examples for platforms
affected by this are the Radxa Rock 5B or the Libre Computer Renegade
Elite ROC-RK3399-PC.
Instead of directly trying a hard reset when no Source Capability
message is send by the USB-PD source automatically, this changes the
state machine to try explicitly asking for the capabilities by sending
a Get Source Capability control message.
For me this solves issues with 2 different USB-PD sources - a RAVPower
powerbank and a Lemorele USB-C dock. Every other PD source I own
follows the specification and automatically sends the Source Capability
message after a soft reset, which works with or without this change.
I decided against making this extra step limited to devices not having
the self_powered flag set, since I don't see any huge drawbacks in this
approach and it keeps the logic simpler. The worst case scenario would
be a power source, which is really stuck. In that case the hard reset
is delayed by another 310ms.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240523171806.223727-1-sebastian.reichel@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The musb driver core already supports external vbus control for ULPI
PHYs, but none of the drivers actually enable it. A customer reported
needing this for their device, and now that a DT property for detecting
this configuration exists, read the property to enable the feature.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240531-spilt-garage-ed2113d628e8@wendy
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'ehci_dbg_port' is unused in oxu210hp-hcd.c since it's original
commit b92a78e582 ("usb host: Oxford OXU210HP HCD driver.")
when it was in a separate header.
Remove it.
Note, that this structure, and some others in the driver
are mostly clones of include/linux/usb/ehci_def.h.
Someone with the hardware to be able to test it might
be able to remove a lot more structs as well and just
use that header.
Signed-off-by: "Dr. David Alan Gilbert" <linux@treblig.org>
Link: https://lore.kernel.org/r/20240529210002.106369-1-linux@treblig.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Newer UCSI versions defined additional notification bits that can be
enabled by the PPM. Add their definitions and convert all definitions
to BIT_ULL() as we now cross the 32-bit boundary.
Signed-off-by: Diogo Ivo <diogo.ivo@tecnico.ulisboa.pt>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/3filrg6mbh6m3galir7ew5juakd25uvksimr7mqd7uc5td3xza@fdvxcewozqeh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using dma_map_sg() to map the scatterlist with iommu enabled,
the entries in the scatterlist can be mergerd into less but longer
entries in the function __finalise_sg(). So that the number of
valid mapped entries is actually smaller than ureq->num_reqs,and
there are still some invalid entries in the scatterlist with
dma_addr=0xffffffff and len=0. Writing these invalid sg entries
into the dma_desc can cause a data transmission error.
The function dma_map_sg() returns the number of valid map entries
and the return value is assigned to usb_request::num_mapped_sgs in
function usb_gadget_map_request_by_dev(). So that just write valid
mapped entries into dma_desc according to the usb_request::num_mapped_sgs,
and set the IOC bit if it's the last valid mapped entry.
This patch poses no risk to no-iommu situation, cause
ureq->num_mapped_sgs equals ureq->num_sgs while using dma_direct_map_sg()
to map the scatterlist whith iommu disabled.
Signed-off-by: Peng Hongchi <hongchi.peng@siengine.com>
Link: https://lore.kernel.org/r/20240523100315.7226-1-hongchi.peng@siengine.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TI USB2 PHY is known to have a lockup issue on very short
suspend intervals. Enable the Suspend Residency quirk flag to
workaround this as described in Errata i2409 [1].
[1] - https://www.ti.com/lit/er/sprz457h/sprz457h.pdf
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20240516044537.16801-3-r-gunasekaran@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some platforms (e.g. ti,j721e-usb, ti,am64-usb) require
this bit to be set to workaround a lockup issue with PHY
short suspend intervals [1]. Add a platform quirk flag
to indicate if Suspend Residency should be enabled.
[1] - https://www.ti.com/lit/er/sprz457h/sprz457h.pdf
i2409 - USB: USB2 PHY locks up due to short suspend
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20240516044537.16801-2-r-gunasekaran@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Skip submitting URBs, when identical requests were already sent in
tweak_special_requests(). Instead call the completion handler directly
to return the result of the URB.
Even though submitting those requests twice should be harmless, there
are USB devices that react poorly to some duplicated requests.
One example is the ChipIdea controller implementation in U-Boot: The
second SET_CONFIGURATION request makes U-Boot disable and re-enable all
endpoints. Re-enabling an endpoint in the ChipIdea controller, however,
was broken until U-Boot commit b272c8792502 ("usb: ci: Fix gadget
reinit").
Signed-off-by: Simon Holesch <simon@holesch.de>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Reviewed-by: Hongren Zheng <i@zenithal.me>
Tested-by: Hongren Zheng <i@zenithal.me>
Link: https://lore.kernel.org/r/20240519141922.171460-1-simon@holesch.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current storage scan delay is reduced by the following old commit.
a4a47bc03f ("Lower USB storage settling delay to something more reasonable")
It means that delay is at least 'one second', or zero with delay_use=0.
'one second' is still long delay especially for embedded system but
when delay_use is set to 0 (no delay), still error observed on some USB drives.
So delay_use should not be set to 0 but 'one second' is quite long.
Especially for embedded system, it's important for end user
how quickly access to USB drive when it's connected.
That's why we have a chance to minimize such a constant long delay.
This patch optimizes scan delay more precisely
to minimize delay time but not to have any problems on USB drives
by extending module parameter 'delay_use' in milliseconds internally.
The parameter 'delay_use' optionally supports in milliseconds
if it ends with 'ms'.
It makes the range of value to 1 / 1000 in internal 32-bit value
but it's still enough to set the delay time.
By default, delay time is 'one second' for backward compatibility.
For example, it seems to be good by changing delay_use=100ms,
that is 100 millisecond delay without issues for most USB pen drives.
Signed-off-by: Norihiko Hama <Norihiko.Hama@alpsalpine.com>
Link: https://lore.kernel.org/r/20240515004339.29892-1-Norihiko.Hama@alpsalpine.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In function nb7vpq904m_parse_data_lanes_mapping(), the "if (ep)"
condition is basically the entire function. Making the code a bit more
readable by inverting the condition so that the function returns
immediately if there is no "ep".
Signed-off-by: R Sundar <prosunofficial@gmail.com>
Link: https://lore.kernel.org/r/20240506162829.5223-1-prosunofficial@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The member "uzonesize" of struct alauda_info will remain 0
if alauda_init_media() fails, potentially causing divide errors
in alauda_read_data() and alauda_write_lba().
- Add a member "media_initialized" to struct alauda_info.
- Change a condition in alauda_check_media() to ensure the
first initialization.
- Add an error check for the return value of alauda_init_media().
Fixes: e80b0fade0 ("[PATCH] USB Storage: add alauda support")
Reported-by: xingwei lee <xrivendell7@gmail.com>
Reported-by: yue sun <samsun1006219@gmail.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Shichao Lai <shichaorai@gmail.com>
Link: https://lore.kernel.org/r/20240526012745.2852061-1-shichaorai@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is possible that also the GET_ERROR command fails. If
that happens, the command completion still needs to be
acknowledged. Otherwise the interface will be stuck until
it's reset.
Reported-by: Ammy Yi <ammy.yi@intel.com>
Fixes: bdc62f2bae ("usb: typec: ucsi: Simplified registration and I/O API")
Cc: stable@vger.kernel.org
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240531104653.1303519-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit 8fea0c8fda ("usb: core: hcd: Convert from tasklet to BH
workqueue"), usb_giveback_urb_bh() runs in the BH workqueue with
interrupts enabled.
Thus, the remote coverage collection section in usb_giveback_urb_bh()->
__usb_hcd_giveback_urb() might be interrupted, and the interrupt handler
might invoke __usb_hcd_giveback_urb() again.
This breaks KCOV, as it does not support nested remote coverage collection
sections within the same context (neither in task nor in softirq).
Update kcov_remote_start/stop_usb_softirq() to disable interrupts for the
duration of the coverage collection section to avoid nested sections in
the softirq context (in addition to such in the task context, which are
already handled).
Reported-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Closes: https://lore.kernel.org/linux-usb/0f4d1964-7397-485b-bc48-11c01e2fcbca@I-love.SAKURA.ne.jp/
Closes: https://syzkaller.appspot.com/bug?extid=0438378d6f157baae1a2
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: 8fea0c8fda ("usb: core: hcd: Convert from tasklet to BH workqueue")
Cc: stable@vger.kernel.org
Acked-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Andrey Konovalov <andreyknvl@gmail.com>
Link: https://lore.kernel.org/r/20240527173538.4989-1-andrey.konovalov@linux.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There could be a potential use-after-free case in
tcpm_register_source_caps(). This could happen when:
* new (say invalid) source caps are advertised
* the existing source caps are unregistered
* tcpm_register_source_caps() returns with an error as
usb_power_delivery_register_capabilities() fails
This causes port->partner_source_caps to hold on to the now freed source
caps.
Reset port->partner_source_caps value to NULL after unregistering
existing source caps.
Fixes: 230ecdf71a ("usb: typec: tcpm: unregister existing source caps before re-registration")
Cc: stable@vger.kernel.org
Signed-off-by: Amit Sunil Dhamne <amitsd@google.com>
Reviewed-by: Ondrej Jirman <megi@xff.cz>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240514220134.2143181-1-amitsd@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If no other USB HCDs are selected when compiling a small pure virutal
machine, the Xen HCD driver cannot be built.
Fix it by traversing down host/ if CONFIG_USB_XEN_HCD is selected.
Fixes: 494ed3997d ("usb: Introduce Xen pvUSB frontend (xen hcd)")
Cc: stable@vger.kernel.org # v5.17+
Signed-off-by: John Ernberg <john.ernberg@actia.se>
Link: https://lore.kernel.org/r/20240517114345.1190755-1-john.ernberg@actia.se
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The new X Elite (x1e80100) platform has three ports so increase the
maximum so that all ports can be registered.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240603100007.10236-1-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the rework of how the __string() handles dynamic strings where it
saves off the source string in field in the helper structure[1], the
assignment of that value to the trace event field is stored in the helper
value and does not need to be passed in again.
This means that with:
__string(field, mystring)
Which use to be assigned with __assign_str(field, mystring), no longer
needs the second parameter and it is unused. With this, __assign_str()
will now only get a single parameter.
There's over 700 users of __assign_str() and because coccinelle does not
handle the TRACE_EVENT() macro I ended up using the following sed script:
git grep -l __assign_str | while read a ; do
sed -e 's/\(__assign_str([^,]*[^ ,]\) *,[^;]*/\1)/' $a > /tmp/test-file;
mv /tmp/test-file $a;
done
I then searched for __assign_str() that did not end with ';' as those
were multi line assignments that the sed script above would fail to catch.
Note, the same updates will need to be done for:
__assign_str_len()
__assign_rel_str()
__assign_rel_str_len()
I tested this with both an allmodconfig and an allyesconfig (build only for both).
[1] https://lore.kernel.org/linux-trace-kernel/20240222211442.634192653@goodmis.org/
Link: https://lore.kernel.org/linux-trace-kernel/20240516133454.681ba6a0@rorschach.local.home
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Christian König <christian.koenig@amd.com> for the amdgpu parts.
Acked-by: Thomas Hellström <thomas.hellstrom@linux.intel.com> #for
Acked-by: Rafael J. Wysocki <rafael@kernel.org> # for thermal
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Darrick J. Wong <djwong@kernel.org> # xfs
Tested-by: Guenter Roeck <linux@roeck-us.net>
Here is the big set of USB and Thunderbolt changes for 6.10-rc1.
Nothing hugely earth-shattering, just constant forward progress for
hardware support of new devices and cleanups over the drivers.
Included in here are:
- Thunderbolt / USB 4 driver updates
- typec driver updates
- dwc3 driver updates
- gadget driver updates
- uss720 driver id additions and fixes (people use USB->arallel port
devices still!)
- onboard-hub driver rename and additions for new hardware
- xhci driver updates
- other small USB driver updates and additions for quirks and api
changes
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZk4E7w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yn0kACgr3uvAWXvfb9R4vCpC65F4f49ZQwAoIkHQBPl
/5HdrlIIYW2OzdUixH3e
=e3pI
-----END PGP SIGNATURE-----
Merge tag 'usb-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt changes for 6.10-rc1.
Nothing hugely earth-shattering, just constant forward progress for
hardware support of new devices and cleanups over the drivers.
Included in here are:
- Thunderbolt / USB 4 driver updates
- typec driver updates
- dwc3 driver updates
- gadget driver updates
- uss720 driver id additions and fixes (people use USB->arallel port
devices still!)
- onboard-hub driver rename and additions for new hardware
- xhci driver updates
- other small USB driver updates and additions for quirks and api
changes
All of these have been in linux-next for a while with no reported
problems"
* tag 'usb-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (154 commits)
drm/bridge: aux-hpd-bridge: correct devm_drm_dp_hpd_bridge_add() stub
usb: fotg210: Add missing kernel doc description
usb: dwc3: core: Fix unused variable warning in core driver
usb: typec: tipd: rely on i2c_get_match_data()
usb: typec: tipd: fix event checking for tps6598x
usb: typec: tipd: fix event checking for tps25750
dt-bindings: usb: qcom,dwc3: fix interrupt max items
usb: fotg210: Use *-y instead of *-objs in Makefile
usb: phy: tegra: Replace of_gpio.h by proper one
usb: typec: ucsi: displayport: Fix potential deadlock
usb: typec: qcom-pmic-typec: split HPD bridge alloc and registration
usb: musc: Remove unused list 'buffers'
usb: dwc3: Wait unconditionally after issuing EndXfer command
usb: gadget: u_audio: Clear uac pointer when freed.
usb: gadget: u_audio: Fix race condition use of controls after free during gadget unbind.
dt-bindings: usb: dwc3: Add QDU1000 compatible
usb: core: Remove the useless struct usb_devmap which is just a bitmap
MAINTAINERS: Remove {ehci,uhci}-platform.c from ARM/VT8500 entry
USB: usb_parse_endpoint: ignore reserved bits
usb: xhci: compact 'trb_in_td()' arguments
...
-----BEGIN PGP SIGNATURE-----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=xjoS
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.10-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Skip E820 checks for MCFG ECAM regions for new (2016+) machines,
since there's no requirement to describe them in E820 and some
platforms require ECAM to work (Bjorn Helgaas)
- Rename PCI_IRQ_LEGACY to PCI_IRQ_INTX to be more specific (Damien
Le Moal)
- Remove last user and pci_enable_device_io() (Heiner Kallweit)
- Wait for Link Training==0 to avoid possible race (Ilpo Järvinen)
- Skip waiting for devices that have been disconnected while
suspended (Ilpo Järvinen)
- Clear Secondary Status errors after enumeration since Master Aborts
and Unsupported Request errors are an expected part of enumeration
(Vidya Sagar)
MSI:
- Remove unused IMS (Interrupt Message Store) support (Bjorn Helgaas)
Error handling:
- Mask Genesys GL975x SD host controller Replay Timer Timeout
correctable errors caused by a hardware defect; the errors cause
interrupts that prevent system suspend (Kai-Heng Feng)
- Fix EDR-related _DSM support, which previously evaluated revision 5
but assumed revision 6 behavior (Kuppuswamy Sathyanarayanan)
ASPM:
- Simplify link state definitions and mask calculation (Ilpo
Järvinen)
Power management:
- Avoid D3cold for HP Pavilion 17 PC/1972 PCIe Ports, where BIOS
apparently doesn't know how to put them back in D0 (Mario
Limonciello)
CXL:
- Support resetting CXL devices; special handling required because
CXL Ports mask Secondary Bus Reset by default (Dave Jiang)
DOE:
- Support DOE Discovery Version 2 (Alexey Kardashevskiy)
Endpoint framework:
- Set endpoint BAR to be 64-bit if the driver says that's all the
device supports, in addition to doing so if the size is >2GB
(Niklas Cassel)
- Simplify endpoint BAR allocation and setting interfaces (Niklas
Cassel)
Cadence PCIe controller driver:
- Drop DT binding redundant msi-parent and pci-bus.yaml (Krzysztof
Kozlowski)
Cadence PCIe endpoint driver:
- Configure endpoint BARs to be 64-bit based on the BAR type, not the
BAR value (Niklas Cassel)
Freescale Layerscape PCIe controller driver:
- Convert DT binding to YAML (Frank Li)
MediaTek MT7621 PCIe controller driver:
- Add DT binding missing 'reg' property for child Root Ports
(Krzysztof Kozlowski)
- Fix theoretical string truncation in PHY name (Sergio Paracuellos)
NVIDIA Tegra194 PCIe controller driver:
- Return success for endpoint probe instead of falling through to the
failure path (Vidya Sagar)
Renesas R-Car PCIe controller driver:
- Add DT binding missing IOMMU properties (Geert Uytterhoeven)
- Add DT binding R-Car V4H compatible for host and endpoint mode
(Yoshihiro Shimoda)
Rockchip PCIe controller driver:
- Configure endpoint BARs to be 64-bit based on the BAR type, not the
BAR value (Niklas Cassel)
- Add DT binding missing maxItems to ep-gpios (Krzysztof Kozlowski)
- Set the Subsystem Vendor ID, which was previously zero because it
was masked incorrectly (Rick Wertenbroek)
Synopsys DesignWare PCIe controller driver:
- Restructure DBI register access to accommodate devices where this
requires Refclk to be active (Manivannan Sadhasivam)
- Remove the deinit() callback, which was only need by the
pcie-rcar-gen4, and do it directly in that driver (Manivannan
Sadhasivam)
- Add dw_pcie_ep_cleanup() so drivers that support PERST# can clean
up things like eDMA (Manivannan Sadhasivam)
- Rename dw_pcie_ep_exit() to dw_pcie_ep_deinit() to make it parallel
to dw_pcie_ep_init() (Manivannan Sadhasivam)
- Rename dw_pcie_ep_init_complete() to dw_pcie_ep_init_registers() to
reflect the actual functionality (Manivannan Sadhasivam)
- Call dw_pcie_ep_init_registers() directly from all the glue
drivers, not just those that require active Refclk from the host
(Manivannan Sadhasivam)
- Remove the "core_init_notifier" flag, which was an obscure way for
glue drivers to indicate that they depend on Refclk from the host
(Manivannan Sadhasivam)
TI J721E PCIe driver:
- Add DT binding J784S4 SoC Device ID (Siddharth Vadapalli)
- Add DT binding J722S SoC support (Siddharth Vadapalli)
TI Keystone PCIe controller driver:
- Add DT binding missing num-viewport, phys and phy-name properties
(Jan Kiszka)
Miscellaneous:
- Constify and annotate with __ro_after_init (Heiner Kallweit)
- Convert DT bindings to YAML (Krzysztof Kozlowski)
- Check for kcalloc() failure in of_pci_prop_intr_map() (Duoming
Zhou)"
* tag 'pci-v6.10-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (97 commits)
PCI: Do not wait for disconnected devices when resuming
x86/pci: Skip early E820 check for ECAM region
PCI: Remove unused pci_enable_device_io()
ata: pata_cs5520: Remove unnecessary call to pci_enable_device_io()
PCI: Update pci_find_capability() stub return types
PCI: Remove PCI_IRQ_LEGACY
scsi: vmw_pvscsi: Do not use PCI_IRQ_LEGACY instead of PCI_IRQ_LEGACY
scsi: pmcraid: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
scsi: mpt3sas: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
scsi: megaraid_sas: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
scsi: ipr: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
scsi: hpsa: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
scsi: arcmsr: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
wifi: rtw89: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
dt-bindings: PCI: rockchip,rk3399-pcie: Add missing maxItems to ep-gpios
Revert "genirq/msi: Provide constants for PCI/IMS support"
Revert "x86/apic/msi: Enable PCI/IMS"
Revert "iommu/vt-d: Enable PCI/IMS"
Revert "iommu/amd: Enable PCI/IMS"
Revert "PCI/MSI: Provide IMS (Interrupt Message Store) support"
...
Updates to the usual drivers (ufs, lpfc, qla2xxx, mpi3mr, libsas).
The major update (which causes a conflict with block, see below) is
Christoph removing the queue limits and their associated block
helpers. The remaining patches are assorted minor fixes and
deprecated function updates plus a bit of constification.
Signed-off-by: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCZkOnWyYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishYe7AP93XRN/
xnccJbSTTUL4FFGobq2CYXv58Na+FM/b/+/kEAD+PNi0LmHDdDTOaFUblMd9l4lj
mpvYLRvJ6ifnHX6WXAg=
=PVnL
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"Updates to the usual drivers (ufs, lpfc, qla2xxx, mpi3mr, libsas).
The major update (which causes a conflict with block, see below) is
Christoph removing the queue limits and their associated block
helpers.
The remaining patches are assorted minor fixes and deprecated function
updates plus a bit of constification"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (141 commits)
scsi: mpi3mr: Sanitise num_phys
scsi: lpfc: Copyright updates for 14.4.0.2 patches
scsi: lpfc: Update lpfc version to 14.4.0.2
scsi: lpfc: Add support for 32 byte CDBs
scsi: lpfc: Change lpfc_hba hba_flag member into a bitmask
scsi: lpfc: Introduce rrq_list_lock to protect active_rrq_list
scsi: lpfc: Clear deferred RSCN processing flag when driver is unloading
scsi: lpfc: Update logging of protection type for T10 DIF I/O
scsi: lpfc: Change default logging level for unsolicited CT MIB commands
scsi: target: Remove unused list 'device_list'
scsi: iscsi: Remove unused list 'connlist_err'
scsi: ufs: exynos: Add support for Tensor gs101 SoC
scsi: ufs: exynos: Add some pa_dbg_ register offsets into drvdata
scsi: ufs: exynos: Allow max frequencies up to 267Mhz
scsi: ufs: exynos: Add EXYNOS_UFS_OPT_TIMER_TICK_SELECT option
scsi: ufs: exynos: Add EXYNOS_UFS_OPT_UFSPR_SECURE option
scsi: ufs: dt-bindings: exynos: Add gs101 compatible
scsi: qla2xxx: Fix debugfs output for fw_resource_count
scsi: qedf: Ensure the copied buf is NUL terminated
scsi: bfa: Ensure the copied buf is NUL terminated
...
kernel-doc validator is not happy:
warning: Function parameter or struct member 'fotg' not described in 'fotg210_vbus'
Add missing description.
Fixes: 3e679bde52 ("usb: fotg210-udc: Implement VBUS session")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240510152641.2421298-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The first thing i2c_get_match_data() does is calling
device_get_match_data(), which already checks if there is a fwnode.
Remove explicit usage of device_get_match_data() as it is already
included in i2c_get_match_data().
Signed-off-by: Javier Carrasco <javier.carrasco@wolfvision.net>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240429-tps6598x_fix_event_handling-v3-3-4e8e58dce489@wolfvision.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current interrupt service routine of the tps6598x only reads the
first 64 bits of the INT_EVENT1 and INT_EVENT2 registers, which means
that any event above that range will be ignored, leaving interrupts
unattended. Moreover, those events will not be cleared, and the device
will keep the interrupt enabled.
This issue has been observed while attempting to load patches, and the
'ReadyForPatch' field (bit 81) of INT_EVENT1 was set.
Given that older versions of the tps6598x (1, 2 and 6) provide 8-byte
registers, a mechanism based on the upper byte of the version register
(0x0F) has been included. The manufacturer has confirmed [1] that this
byte is always 0 for older versions, and either 0xF7 (DH parts) or 0xF9
(DK parts) is returned in newer versions (7 and 8).
Read the complete INT_EVENT registers to handle all interrupts generated
by the device and account for the hardware version to select the
register size.
Link: https://e2e.ti.com/support/power-management-group/power-management/f/power-management-forum/1346521/tps65987d-register-command-to-distinguish-between-tps6591-2-6-and-tps65987-8 [1]
Fixes: 0a4c005bd1 ("usb: typec: driver for TI TPS6598x USB Power Delivery controllers")
Cc: stable@vger.kernel.org
Signed-off-by: Javier Carrasco <javier.carrasco@wolfvision.net>
Link: https://lore.kernel.org/r/20240429-tps6598x_fix_event_handling-v3-2-4e8e58dce489@wolfvision.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In its current form, the interrupt service routine of the tps25750
checks the event flags in the lowest 64 bits of the interrupt event
register (event[0]), but also in the upper part (event[1]).
Given that all flags are defined as BIT() or BIT_ULL(), they are
restricted to the first 64 bits of the INT_EVENT1 register. Including
the upper part of the register can lead to false positives e.g. if the
event 64 bits above the one being checked is set, but the one being
checked is not.
Restrict the flag checking to the first 64 bits of the INT_EVENT1
register.
Fixes: 7e7a3c815d ("USB: typec: tps6598x: Add TPS25750 support")
Cc: stable@vger.kernel.org
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Javier Carrasco <javier.carrasco@wolfvision.net>
Link: https://lore.kernel.org/r/20240429-tps6598x_fix_event_handling-v3-1-4e8e58dce489@wolfvision.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
*-objs suffix is reserved rather for (user-space) host programs while
usually *-y suffix is used for kernel drivers (although *-objs works
for that purpose for now).
Let's correct the old usages of *-objs in Makefiles.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240508150406.1378672-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function ucsi_displayport_work() does not access the
connector, so it also must not acquire the connector lock.
This fixes a potential deadlock scenario:
ucsi_displayport_work() -> lock(&con->lock)
typec_altmode_vdm()
dp_altmode_vdm()
dp_altmode_work()
typec_altmode_enter()
ucsi_displayport_enter() -> lock(&con->lock)
Reported-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Fixes: af8622f6a5 ("usb: typec: ucsi: Support for DisplayPort alt mode")
Cc: stable@vger.kernel.org
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240507134316.161999-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a probe function returns -EPROBE_DEFER after creating another device
there is a change of ending up in a probe deferral loop, (see commit
fbc35b45f9 ("Add documentation on meaning of -EPROBE_DEFER"). In case
of the qcom-pmic-typec driver the tcpm_register_port() function looks up
external resources (USB role switch and inherently via called
typec_register_port() USB-C muxes, switches and retimers).
In order to prevent such probe-defer loops caused by qcom-pmic-typec
driver, use the API added by Johan Hovold and move HPD bridge
registration to the end of the probe function.
The devm_drm_dp_hpd_bridge_add() is called at the end of the probe
function after all TCPM start functions. This is done as a way to
overcome a different problem, the DRM subsystem can not properly cope
with the DRM bridges being destroyed once the bridge is attached. Having
this function call at the end of the probe function prevents possible
DRM bridge device creation followed by destruction in case one of the
TCPM start functions returns an error.
Reported-by: Caleb Connolly <caleb.connolly@linaro.org>
Acked-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240424-qc-pmic-typec-hpd-split-v4-1-f7e10d147443@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the unused list head 'buffers' and the
'struct free_record' which is also unused below it.
To me it looks like this has always been unused, but I've
not dug into why.
Build test only.
Signed-off-by: "Dr. David Alan Gilbert" <linux@treblig.org>
Link: https://lore.kernel.org/r/20240504150315.77598-1-linux@treblig.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently all controller IP/revisions except DWC3_usb3 >= 310a
wait 1ms unconditionally for ENDXFER completion when IOC is not
set. This is because DWC_usb3 controller revisions >= 3.10a
supports GUCTL2[14: Rst_actbitlater] bit which allows polling
CMDACT bit to know whether ENDXFER command is completed.
Consider a case where an IN request was queued, and parallelly
soft_disconnect was called (due to ffs_epfile_release). This
eventually calls stop_active_transfer with IOC cleared, hence
send_gadget_ep_cmd() skips waiting for CMDACT cleared during
EndXfer. For DWC3 controllers with revisions >= 310a, we don't
forcefully wait for 1ms either, and we proceed by unmapping the
requests. If ENDXFER didn't complete by this time, it leads to
SMMU faults since the controller would still be accessing those
requests.
Fix this by ensuring ENDXFER completion by adding 1ms delay in
__dwc3_stop_active_transfer() unconditionally.
Cc: stable@vger.kernel.org
Fixes: b353eb6dc2 ("usb: dwc3: gadget: Skip waiting for CMDACT cleared during endxfer")
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240502044103.1066350-1-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmY39LkeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGaB8H+wWcwT1O7K2SQx1a
sHDYJSXfbjgShS7Wt+gbDNvhGJqG/5FkpHyBmBKUdElZs8QMf21GAbIfJvzcNThA
g+FakIMjfhNH/dr6TJXHWbb2NZV67exDbbuaQDyMhNhIZqil4BH/OEPbLYIdquvm
/HDGFB/whVoHVC+Ug8esEOL3Uy+rizBDlsT/K4ZgpOC3TuUmlRpptSVACwjcCGXM
PFKyyTIr0ZnKcz3+4yTEtpDFm6e/ujxMwM66GBCgmPaZ3lJp5ruY3kGpBTmSyoqV
Rh3CQlIhBo8gwlAx/yQXfxEZomhxT6DfRpc6s/1W0J1UZN/j2pYy056OYyckG32c
uQ9ujxQ=
=M0wP
-----END PGP SIGNATURE-----
Merge 6.9-rc7 into usb-next
We want the USB fixes in here as well, and resolve a merge conflict in
drivers/usb/dwc3/core.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reading bEndpointAddress the spec tells is that:
b7 is direction, which must be ignored
b6:4 are reserved which are to be set to zero
b3:0 are the endpoint address
In order to be backwards compatible with possible future versions of USB
we have to be ready with devices using those bits. That means that we
also have to ignore them like we do with the direction bit.
In consequence the only illegal address you can encoding in four bits is
endpoint zero, for which no descriptor must exist. Hence the check for
exceeding the upper limit on endpoint addresses is removed.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20240502115259.31076-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove unnecessary repeated calls to TRB_TO_SLOT_ID(). The slot ID is
stored in the 'slot_id' variable at the function's start.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-18-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's better to keep track on Thunderbolt xHCI IDs in a separate group.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-16-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are three out of many Intel platforms that are using TLAs
instead of the full names in the PCI IDs. Modify them accordingly.
This also fixes the logic of grouping as seemed to be by an LSB
byte of the ID.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-15-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By removing the goto 'cleanup' statement, and replacing it with 'continue',
'break' and 'return', helps simplify the code and further showcase in which
case the while loop iterates.
This change prepares for the comprehensive handle_tx_event() rework.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-14-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplifying the handle_tx_event() function by addressing the complexity
of its while loop. Replaces specific 'goto cleanup' statements with
'return' statements, applicable only where 'ep->skip' is set to 'false',
ensuring loop termination.
The original while loop, combined with 'goto cleanup', adds unnecessary
complexity. This change aims to untangle the loop's logic, facilitating a
more straightforward review of the upcoming comprehensive rework.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-13-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When handle_tx_event() encounters a COMP_MISSED_SERVICE_ERROR or
COMP_NO_PING_RESPONSE_ERROR event, it moves to 'goto cleanup'.
Here, it sets a flag, 'handling_skipped_tds', based on conditions that
exclude these two error events.
Subsequently, the process evaluates the loop that persists as long as
'handling_skipped_tds' remains true. However, since 'trb_comp_code' does
not change after its assignment, if it indicates either of the two error
conditions, the loop terminates immediately.
To simplify this process and enhance clarity, the modification involves
returning immediately upon detecting COMP_MISSED_SERVICE_ERROR or
COMP_NO_PING_RESPONSE_ERROR. This adjustment allows for the direct use of
'ep->skip', removing the necessity for the 'handling_skipped_tds' flag.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-12-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some transfer events don't always point to a TRB, and consequently don't
have a endpoint ring. In these cases, function handle_tx_event() should
not proceed, because if 'ep->skip' is set, the pointer to the endpoint
ring is used.
To prevent a potential failure and make the code logical, return after
checking the completion code for a Transfer event without TRBs.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-11-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If this quirk was set then driver would treat transfer events with
'Success' completion code as 'Short packet' if there were untransferred
bytes left.
This is so common that turn it into default behavior.
xhci_warn_ratelimited() is no longer used after this, so remove it.
A success event with untransferred bytes left doesn't always mean a
misbehaving controller. If there was an error mid a multi-TRB TD it's
allowed to issue a success event for the last TRB in that TD.
See xhci 1.2 spec 4.9.1 Transfer Descriptors
"Note: If an error is detected while processing a multi-TRB TD, the xHC
shall generate a Transfer Event for the TRB that the error was detected
on with the appropriate error Condition Code, then may advance to the
next TD. If in the process of advancing to the next TD, a Transfer TRB
is encountered with its IOC flag set, then the Condition Code of the
Transfer Event generated for that Transfer TRB should be Success,
because there was no error actually associated with the TRB that
generated the Event. However, an xHC implementation may redundantly
assert the original error Condition Code."
Co-developed-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-10-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Print the full hex value of PORTSC register in addition to the human
readable decoded string while debugging PORTSC value.
If PORTSC value is 0xffffffff then don't decode it.
This lets us inspect Rsvd bits of PORTSC.
Same is done for USBSTS register values.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-9-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace size_mul() with array_size() in memory allocation and freeing
processes, it fits better semantically.
Macro array_size() is identical to size_mult(), which clamps the max size,
so it's imperative that array_size() is used when freeing said memory.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'erst_size' represents the maximum capacity of entries that ERST can hold,
while 'num_entries' indicates the actual number of entries currently held
in the ERST. These two values are identical because the xhci driver does
not support ERST expansion. Thus, 'erst_size' is removed.
Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reduce the number of do-while loops by 1. The number of loops should be
number of segment + 1, the +1 is in case deq and enq are on the same
segment. But due to the use of a do-while loop, the expression is
evaluated after executing the loop, thus the loop is executed 1 extra
time.
Changing the do-while loop expression from "<=" to "<", reduces the loop
amount by 1. The expression "<=" would also work if it was a while loop
instead of a do-while loop.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Address debug message inaccuracies in xhci_ring_expansion_needed().
Specifically, remove the portion of the debug message that indicates the
number of enqueue TRBs to be added to the dequeue segment. This part of
the message may mislead and the calculated value is incorrect. Given that
this value is not of significant importance and the statement is not
consistently accurate, it has been omitted.
The specific issues with the debug message that this commit resolves:
- The calculation of the number of TRBs is incorrect. The current
calculation erroneously includes the link TRB, which is reserved.
Furthermore, the calculated number of TRBs can exceed the dequeue
segment, resulting in a misleading debug message.
- The current phrasing suggests that "ring expansion by X is needed,
adding X TRBs moves enqueue Y TRBs into the dequeue segment".
The intended message, however, is "IF the ring is NOT expanded by X,
THEN adding X TRBs moves enqueue Y TRBs into the dequeue segment".
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check if requested segments ('segs' or 'ERST_DEFAULT_SEGS') exceeds the
maximum amount ERST supports.
When 'segs' is '0', 'ERST_DEFAULT_SEGS' is used instead. But both values
may not exceed ERST max.
Macro 'ERST_MAX_SEGS' is renamed to 'ERST_DEFAULT_SEGS'. The new name
better represents the macros, which is the number of Event Ring segments
to allocate, when the amount is not specified.
Additionally, rename and change xhci_create_secondary_interrupter()'s
argument 'int num_segs' to 'unsigned int segs'. This makes it the same
as its counter part in xhci_alloc_interrupter().
Fixes: c99b38c412 ("xhci: add support to allocate several interrupters")
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This helper was only called from one function.
Removing it both reduces lines of code and made it more readable.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Port capability flags for USB2 ports have been cached in an
u32 xhci->ext_caps[] array long before the driver had struct xhci_port
and struct xhci_port_cap structures.
Move these cached USB2 port capability values together with the other
port capability values into struct xhci_port_cap cability structure.
This also gets rid of the cumbersome way of mapping port to USB2
capability based on portnum as each port has a pointer to its capability
structure.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
typec_register_partner() does not guarantee partner registration
to always succeed. In the event of failure, port->partner is set
to the error value or NULL. Given that port->partner validity is
not checked, this results in the following crash:
Unable to handle kernel NULL pointer dereference at virtual address xx
pc : run_state_machine+0x1bc8/0x1c08
lr : run_state_machine+0x1b90/0x1c08
..
Call trace:
run_state_machine+0x1bc8/0x1c08
tcpm_state_machine_work+0x94/0xe4
kthread_worker_fn+0x118/0x328
kthread+0x1d0/0x23c
ret_from_fork+0x10/0x20
To prevent the crash, check for port->partner validity before
derefencing it in all the call sites.
Cc: stable@vger.kernel.org
Fixes: c97cd0b4b5 ("usb: typec: tcpm: set initial svdm version based on pd revision")
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240427202812.3435268-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before sending Enter Mode for an Alt Mode, there is a gap between Discover
Modes and the Alt Mode driver queueing the Enter Mode VDM for the port
partner to send a message to the port.
If this message results in unregistering Alt Modes such as in a DR_SWAP,
then the following deadlock can occur with respect to the DisplayPort Alt
Mode driver:
1. The DR_SWAP state holds port->lock. Unregistering the Alt Mode driver
results in a cancel_work_sync() that waits for the current dp_altmode_work
to finish.
2. dp_altmode_work makes a call to tcpm_altmode_enter. The deadlock occurs
because tcpm_queue_vdm_unlock attempts to hold port->lock.
Before attempting to grab the lock, ensure that the port is in a state
vdm_run_state_machine can run in. Alt Mode unregistration will not occur
in these states.
Fixes: 03eafcfb60 ("usb: typec: tcpm: Add tcpm_queue_vdm_unlocked() helper")
Cc: stable@vger.kernel.org
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240423202356.3372314-2-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a Fast Role Swap control message attempt results in a transition
to ERROR_RECOVERY, the TCPC can still queue a TCPM_SOURCING_VBUS event.
If the event is queued but processed after the tcpm_reset_port() call
in the PORT_RESET state, then the following occurs:
1. tcpm_reset_port() calls tcpm_init_vbus() to reset the vbus sourcing and
sinking state
2. tcpm_pd_event_handler() turns VBUS on before the port is in the default
state.
3. The port resolves as a sink. In the SNK_DISCOVERY state,
tcpm_set_charge() cannot set vbus to charge.
Clear pd events within PORT_RESET to get rid of non-applicable events.
Fixes: b17dd57118 ("staging: typec: tcpm: Improve role swap with non PD capable partners")
Cc: stable@vger.kernel.org
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240423202715.3375827-2-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Exynos-based Google Tensor gs101 SoC has a DWC3 compatible USB
controller and can reuse the existing Exynos glue. Add the
google,gs101-dwusb3 compatible and associated driver data. Four clocks
are required for USB for this SoC:
* bus clock
* suspend clock
* Link interface AXI clock
* Link interface APB clock
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240423-usb-dwc3-gs101-v1-2-2f331f88203f@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
interacting with "usb: misc: onboard_usb_hub: Disable the USB hub clock
on failure"
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://lore.kernel.org/r/20240424161202.7e45e19e@canb.auug.org.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Testing ohci functionality with qemu's pci-ohci emulation often results
in ohci interface stalls, resulting in hung task timeouts.
The problem is caused by lost interrupts between the emulation and the
Linux kernel code. Additional interrupts raised while the ohci interrupt
handler in Linux is running and before the handler clears the interrupt
status are not handled. The fix for a similar problem in ehci suggests
that the problem is likely caused by edge-triggered MSI interrupts. See
commit 0b60557230 ("usb: ehci: Prevent missed ehci interrupts with
edge-triggered MSI") for details.
Ensure that the ohci interrupt code handles all pending interrupts before
returning to solve the problem.
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: David Laight <David.Laight@aculab.com>
Cc: stable@vger.kernel.org
Fixes: 306c54d0ed ("usb: hcd: Try MSI interrupts on PCI devices")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Link: https://lore.kernel.org/r/20240429154010.1507366-1-linux@roeck-us.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recent commit introduced support for reading Multiport PHYs and
while doing so iterated over an integer variable which runs from
[0-254] in the worst case scenario. But S390 compiler treats it as a
warning and complains that the integer write to string can go to 11
characters. Fix this by modifying iterator variable to u8.
Suggested-by: Johan Hovold <johan@kernel.org>
Fixes: 30a46746ca ("usb: dwc3: core: Refactor PHY logic to support Multiport Controller")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202404241215.Mib19Cu7-lkp@intel.com/
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240426050512.57384-1-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the macro PCI_IRQ_INTX instead of the deprecated PCI_IRQ_LEGACY macro.
Link: https://lore.kernel.org/r/20240325070944.3600338-6-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Power event IRQ is used for wakeup either when the controller is
SuperSpeed capable but is missing an SuperSpeed PHY interrupt, or when
the GIC is not capable of detecting DP/DM High-Speed PHY interrupts.
The Power event IRQ stat register indicates whether the High-Speed
phy entered and exited L2 successfully during suspend and resume.
Indicate the same for all ports of a multiport controller.
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240420044901.884098-10-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DWC3 Qcom wrapper currently supports only wakeup configuration
for single port controllers. Read speed of each port connected
to the controller and enable wakeup for each of them accordingly.
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240420044901.884098-9-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On multiport supported controllers, each port has its own DP/DM and
SuperSpeed (if super speed capable) interrupts. As per the bindings,
their interrupt names differ from single-port ones by having a "_x"
added as suffix (x being the port number). Identify from the interrupt
names whether the controller is a multiport controller or not.
Refactor dwc3_qcom_setup_irq() call to parse multiportinterrupts along
with non-multiport ones accordingly.
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240420044901.884098-8-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The logic for requesting interrupts is duplicated for each interrupt. In
the upcoming patches that introduces support for multiport, it would be
better to clean up the duplication before reading mulitport related
interrupts.
Refactor interrupt setup call by adding a new helper function for
requesting the wakeup interrupts. To simplify implementation, make
the display name same as the interrupt name expected in Device tree.
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240420044901.884098-7-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the DWC3 driver supports only single port controller
which requires at least one HS PHY and at most one SS PHY.
But the DWC3 USB controller can be connected to multiple ports and
each port can have their own PHYs. Each port of the multiport
controller can either be HS+SS capable or HS only capable
Proper quantification of them is required to modify GUSB2PHYCFG
and GUSB3PIPECTL registers appropriately.
DWC3 multiport controllers are capable to service at most 15 High Speed
PHYs and 4 Supser Speed PHYs. Add support for detecting, obtaining and
configuring PHYs supported by a multiport controller.
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240420044901.884098-5-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some SoC's like SA8295P where the tertiary controller is host-only
capable, GEVTADDRHI/LO, GEVTSIZ, GEVTCOUNT registers are not accessible.
Trying to access them leads to a crash.
For DRD/Peripheral supported controllers, event buffer setup is done
again in gadget_pullup. Skip setup or cleanup of event buffers if
controller is host-only capable.
Suggested-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240420044901.884098-4-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All DWC3 Multi Port controllers that exist today only support host mode.
Temporarily map XHCI address space for host-only controllers and parse
XHCI Extended Capabilities registers to read number of usb2 ports and
usb3 ports present on multiport controller. Each USB Port is at least HS
capable.
The port info for usb2 and usb3 phy are identified as num_usb2_ports
and num_usb3_ports and these are used as iterators for phy operations
and for modifying GUSB2PHYCFG/ GUSB3PIPECTL registers accordingly.
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240420044901.884098-3-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move disabling of the vdd-pdphy supply to the start() function which
enabled it for symmetry and to make sure that it is disabled as intended
in all error paths of pmic_typec_pdphy_reset() (i.e. not just when
qcom_pmic_typec_pdphy_enable() fails).
Cc: stable+noautosel@kernel.org # Not needed in any stable release, just a minor bugfix
Fixes: a4422ff221 ("usb: typec: qcom: Add Qualcomm PMIC Type-C driver")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240418145730.4605-3-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to stop and deregister the port in case of late probe errors
to avoid use-after-free issues when the underlying memory is released by
devres.
Fixes: a4422ff221 ("usb: typec: qcom: Add Qualcomm PMIC Type-C driver")
Cc: stable@vger.kernel.org # 6.5
Cc: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240418145730.4605-2-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the USB driver passes a pointer into the TRB buffer for creq, this
buffer can be overwritten with the status response as soon as the event
is queued. This can make the final check return USB_GADGET_DELAYED_STATUS
when it shouldn't. Instead use the stored wLength.
Fixes: 4d644abf25 ("usb: gadget: f_fs: Only return delayed status when len is 0")
Cc: stable <stable@kernel.org>
Signed-off-by: Chris Wulff <chris.wulff@biamp.com>
Link: https://lore.kernel.org/r/CO1PR17MB5419BD664264A558B2395E28E1112@CO1PR17MB5419.namprd17.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Testing with KASAN and syzkaller revealed a bug in port.c:disable_store():
usb_hub_to_struct_hub() can return NULL if the hub that the port belongs to
is concurrently removed, but the function does not check for this
possibility before dereferencing the returned value.
It turns out that the first dereference is unnecessary, since hub->intfdev
is the parent of the port device, so it can be changed easily. Adding a
check for hub == NULL prevents further problems.
The same bug exists in the disable_show() routine, and it can be fixed the
same way.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Yue Sun <samsun1006219@gmail.com>
Reported-by: xingwei lee <xrivendell7@gmail.com>
Link: https://lore.kernel.org/linux-usb/CAEkJfYON+ry7xPx=AiLR9jzUNT+i_Va68ACajOC3HoacOfL1ig@mail.gmail.com/
Fixes: f061f43d74 ("usb: hub: port: add sysfs entry to switch port power")
CC: Michael Grzeschik <m.grzeschik@pengutronix.de>
CC: stable@vger.kernel.org
Link: https://lore.kernel.org/r/393aa580-15a5-44ca-ad3b-6462461cd313@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GUSB3PIPECTL.SUSPENDENABLE and GUSB2PHYCFG.SUSPHY should be cleared
during initialization. Suspend during initialization can result in
undefined behavior due to clock synchronization failure, which often
seen as core soft reset timeout.
The programming guide recommended these bits to be cleared during
initialization for DWC_usb3.0 version 1.94 and above (along with
DWC_usb31 and DWC_usb32). The current check in the driver does not
account if it's set by default setting from coreConsultant.
This is especially the case for DRD when switching mode to ensure the
phy clocks are available to change mode. Depending on the
platforms/design, some may be affected more than others. This is noted
in the DWC_usb3x programming guide under the above registers.
Let's just disable them during driver load and mode switching. Restore
them when the controller initialization completes.
Note that some platforms workaround this issue by disabling phy suspend
through "snps,dis_u3_susphy_quirk" and "snps,dis_u2_susphy_quirk" when
they should not need to.
Cc: stable@vger.kernel.org
Fixes: 9ba3aca8fe ("usb: dwc3: Disable phy suspend after power-on reset")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20da4e5a0c4678c9587d3da23f83bdd6d77353e9.1713394973.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit fixes uvc gadget support on 32-bit platforms.
Commit 0df28607c5 ("usb: gadget: uvc: Generalise helper functions for
reuse") introduced a helper function __uvcg_iter_item_entries() to aid
with parsing lists of items on configfs attributes stores. This function
is a generalization of another very similar function, which used a
stack-allocated temporary buffer of fixed size for each item in the list
and used the sizeof() operator to check for potential buffer overruns.
The new function was changed to allocate the now variably sized temp
buffer on heap, but wasn't properly updated to also check for max buffer
size using the computed size instead of sizeof() operator.
As a result, the maximum item size was 7 (plus null terminator) on
64-bit platforms, and 3 on 32-bit ones. While 7 is accidentally just
barely enough, 3 is definitely too small for some of UVC configfs
attributes. For example, dwFrameInteval, specified in 100ns units,
usually has 6-digit item values, e.g. 166666 for 60fps.
Cc: stable@vger.kernel.org
Fixes: 0df28607c5 ("usb: gadget: uvc: Generalise helper functions for reuse")
Signed-off-by: Ivan Avdeev <me@provod.works>
Link: https://lore.kernel.org/r/20240413150124.1062026-1-me@provod.works
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The OS descriptors logic had the high/low byte of w_value inverted, causing
the extended properties to not be accessible for interface != 0.
>From the Microsoft documentation:
https://learn.microsoft.com/en-us/windows-hardware/drivers/usbcon/microsoft-os-1-0-descriptors-specification
OS_Desc_CompatID.doc (w_index = 0x4):
- wValue:
High Byte = InterfaceNumber. InterfaceNumber is set to the number of the
interface or function that is associated with the descriptor, typically
0x00. Because a device can have only one extended compat ID descriptor,
it should ignore InterfaceNumber, regardless of the value, and simply
return the descriptor.
Low Byte = 0. PageNumber is used to retrieve descriptors that are larger
than 64 KB. The header section is 16 bytes, so PageNumber is set to 0 for
this request.
We currently do not support >64KB compat ID descriptors, so verify that the
low byte is 0.
OS_Desc_Ext_Prop.doc (w_index = 0x5):
- wValue:
High byte = InterfaceNumber. The high byte of wValue is set to the number
of the interface or function that is associated with the descriptor.
Low byte = PageNumber. The low byte of wValue is used to retrieve
descriptors that are larger than 64 KB. The header section is 10 bytes, so
PageNumber is set to 0 for this request.
We also don't support >64KB extended properties, so verify that the low byte
is 0 and use the high byte for the interface number.
Fixes: 37a3a53342 ("usb: gadget: OS Feature Descriptors support")
Cc: stable <stable@kernel.org>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Link: https://lore.kernel.org/r/20240404100635.3215340-1-peter@korsgaard.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
FFS based applications can utilize the aio_cancel() callback to dequeue
pending USB requests submitted to the UDC. There is a scenario where the
FFS application issues an AIO cancel call, while the UDC is handling a
soft disconnect. For a DWC3 based implementation, the callstack looks
like the following:
DWC3 Gadget FFS Application
dwc3_gadget_soft_disconnect() ...
--> dwc3_stop_active_transfers()
--> dwc3_gadget_giveback(-ESHUTDOWN)
--> ffs_epfile_async_io_complete() ffs_aio_cancel()
--> usb_ep_free_request() --> usb_ep_dequeue()
There is currently no locking implemented between the AIO completion
handler and AIO cancel, so the issue occurs if the completion routine is
running in parallel to an AIO cancel call coming from the FFS application.
As the completion call frees the USB request (io_data->req) the FFS
application is also referencing it for the usb_ep_dequeue() call. This can
lead to accessing a stale/hanging pointer.
commit b566d38857 ("usb: gadget: f_fs: use io_data->status consistently")
relocated the usb_ep_free_request() into ffs_epfile_async_io_complete().
However, in order to properly implement locking to mitigate this issue, the
spinlock can't be added to ffs_epfile_async_io_complete(), as
usb_ep_dequeue() (if successfully dequeuing a USB request) will call the
function driver's completion handler in the same context. Hence, leading
into a deadlock.
Fix this issue by moving the usb_ep_free_request() back to
ffs_user_copy_worker(), and ensuring that it explicitly sets io_data->req
to NULL after freeing it within the ffs->eps_lock. This resolves the race
condition above, as the ffs_aio_cancel() routine will not continue
attempting to dequeue a request that has already been freed, or the
ffs_user_copy_work() not freeing the USB request until the AIO cancel is
done referencing it.
This fix depends on
commit b566d38857 ("usb: gadget: f_fs: use io_data->status
consistently")
Fixes: 2e4c7553cd ("usb: gadget: f_fs: add aio support")
Cc: stable <stable@kernel.org> # b566d38857 ("usb: gadget: f_fs: use io_data->status consistently")
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240409014059.6740-1-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some new modem device ids for 6.9-rc5.
All have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCZiJlDQAKCRALxc3C7H1l
CHssAQDRloOpuKCJJjVrr8PDdLSh9IkCSX82ashJIys9lEHXEAEAhBGJAucsTMBX
gvszixRlGe6nfO9M5JTUy8+sBMEZyAw=
=1mFa
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-6.9-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial device ids for 6.9-rc5
Here are some new modem device ids for 6.9-rc5.
All have been in linux-next with no reported issues.
* tag 'usb-serial-6.9-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add Telit FN920C04 rmnet compositions
USB: serial: option: add Rolling RW101-GL and RW135-GL support
USB: serial: option: add Lonsung U8300/U9300 product
USB: serial: option: add support for Fibocom FM650/FG650
USB: serial: option: support Quectel EM060K sub-models
USB: serial: option: add Fibocom FM135-GL variants
This macro has the advantage over SIMPLE_DEV_PM_OPS that we don't have to
care about when the functions are actually used.
Also make use of pm_sleep_ptr() to discard all PM_SLEEP related
stuff if CONFIG_PM_SLEEP isn't enabled.
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240412142317.5191-6-linux.amoon@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This macro has the advantage over SIMPLE_DEV_PM_OPS that we don't have to
care about when the functions are actually used.
Also make use of pm_ptr() to discard all PM related stuff if CONFIG_PM
isn't enabled.
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Link: https://lore.kernel.org/r/20240412142317.5191-5-linux.amoon@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The devm_clk_get_enabled() helpers:
- call devm_clk_get()
- call clk_prepare_enable() and register what is needed in order to
call clk_disable_unprepare() when needed, as a managed resource.
This simplifies the code and avoids the calls to clk_disable_unprepare().
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Link: https://lore.kernel.org/r/20240412142317.5191-4-linux.amoon@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This macro has the advantage over SIMPLE_DEV_PM_OPS that we don't have to
care about when the functions are actually used.
Also make use of pm_ptr() to discard all PM related stuff if CONFIG_PM
isn't enabled.
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Link: https://lore.kernel.org/r/20240412142317.5191-3-linux.amoon@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The devm_clk_get_enabled() helpers:
- call devm_clk_get()
- call clk_prepare_enable() and register what is needed in order to
call clk_disable_unprepare() when needed, as a managed resource.
This simplifies the code and avoids the calls to clk_disable_unprepare().
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20240412142317.5191-2-linux.amoon@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The renesas_usbhs_get_info() wrapper was useful for legacy board code.
Since commit 1fa59bda21 ("ARM: shmobile: Remove legacy board code
for Armadillo-800 EVA") in v4.3, it is no longer used outside the USBHS
driver, and provides no added value over dev_get_platdata(), while
obfuscating the real operation.
Drop it, and replace it by dev_get_platdata() in its sole user.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/fa296af4452dfe394a58b75fd44c3bb9591936eb.1713282736.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dwc->maximum_speed is determined through the device capability and
designer's constraint through device tree binding. If none of them
applies, don't let the default coreConsultant setting in GUCTL1 to limit
the device operating speed.
Normally the default setting will not contradict the device capability
or device tree binding. This scenario was found through our internal
tests, not an actual bug in the wild.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/65003b0cc37c08a0d22996009f548247ad18c00c.1713308949.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the PMIC-GLINK device has orientation GPIOs declared, then it will
report connection orientation. In this case set the flag to mark
registered ports as orientation-aware.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240411-ucsi-orient-aware-v2-5-d4b1cb22a33f@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a callback to allow glue drivers to update the connector before
registering corresponding power supply and Type-C port. In particular
this is useful if glue drivers want to touch the connector's Type-C
capabilities structure.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240411-ucsi-orient-aware-v2-4-d4b1cb22a33f@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use typec_set_orientation() instead of calling typec_switch_set()
manually. This way the rest of the typec framework and the userspace are
notified about the orientation change.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240411-ucsi-orient-aware-v2-3-d4b1cb22a33f@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To simplify the platform code move Type-C orientation handling into the
connector_status callback. As it is called both during connector
registration and on connector change events, duplicated code from
pmic_glink_ucsi_register() can be dropped.
Also this moves operations that can sleep into a worker thread,
removing the only sleeping operation from pmic_glink_ucsi_notify().
Tested-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogeurs@linux.intel.com>
Link: https://lore.kernel.org/r/20240411-ucsi-orient-aware-v2-2-d4b1cb22a33f@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allow UCSI glue driver to perform addtional work to update connector
status. For example, it might check the cable orientation. This call is
performed after reading new connector statatus, so the platform driver
can peek at new connection status bits.
The callback is called both when registering the port and when the
connector change event is being handled.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240411-ucsi-orient-aware-v2-1-d4b1cb22a33f@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the transfer polling interval is set to 1ms, which is the
frame rate of full-speed and low-speed USB. The USB 2.0 specification
introduces microframes (125 microseconds) to improve the timing
precision of data transfers.
Reducing the transfer interval to 1 microframe increases data throughput
for high-speed and super-speed USB communication
Signed-off-by: Marcello Sylvester Bauer <marcello.bauer@9elements.com>
Signed-off-by: Marcello Sylvester Bauer <sylv@sylv.io>
Link: https://lore.kernel.org/r/6295dbb84ca76884551df9eb157cce569377a22c.1712843963.git.sylv@sylv.io
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dummy_hcd transfer scheduler assumes that the internal kernel timer
frequency is set to 1000Hz to give a polling interval of 1ms. Reducing
the timer frequency will result in an anti-proportional reduction in
transfer performance. Switch to a hrtimer to decouple this association.
Signed-off-by: Marcello Sylvester Bauer <marcello.bauer@9elements.com>
Signed-off-by: Marcello Sylvester Bauer <sylv@sylv.io>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/57a1c2180ff74661600e010c234d1dbaba1d0d46.1712843963.git.sylv@sylv.io
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ida_alloc() and ida_free() should be preferred to the deprecated
ida_simple_get() and ida_simple_remove().
Note that the upper limit of ida_simple_get() is exclusive, but the one of
ida_alloc_max() is inclusive. So a -1 has been added when needed.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/7cd361e2b377a5373968fa7deee4169229992a1e.1713107386.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DWC3_EP_RESOURCE_ALLOCATED flag ensures that the resource of an
endpoint is only assigned once. Unless the endpoint is reset, don't
clear this flag. Otherwise we may set endpoint resource again, which
prevents the driver from initiate transfer after handling a STALL or
endpoint halt to the control endpoint.
Cc: stable@vger.kernel.org
Fixes: b311048c17 ("usb: dwc3: gadget: Rewrite endpoint allocation flow")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/00122b7cc5be06abef461776e7cc9f5ebc8bc1cb.1713229786.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 339f83612f.
It has been found to cause problems in a number of Chromebook devices,
so revert the change until it can be brought back in a safe way.
Link: https://lore.kernel.org/r/385a3519-b45d-48c5-a6fd-a3fdb6bec92f@chromium.org
Reported-by:: Aleksander Morgado <aleksandermj@chromium.org>
Fixes: 339f83612f ("usb: cdc-wdm: close race between read and workqueue")
Cc: stable <stable@kernel.org>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to the ->device_configure method instead of ->slave_alloc and update
the block limits on the passed in queue_limits instead of using the
per-limit accessors.
Note that uas was the only driver setting these size limits from
->slave_alloc and not ->slave_configure and this makes it match everyone
else.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20240409143748.980206-23-hch@lst.de
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Switch to the ->device_configure method instead of ->slave_configure and
update the block limits on the passed in queue_limits instead of using the
per-limit accessors.
Also use the proper atomic queue limit update helpers and freeze the queue
when updating max_hw_sectors from sysfs.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20240409143748.980206-18-hch@lst.de
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Get drivers out of the business of having to call the block layer DMA
alignment limits helpers themselves.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20240409143748.980206-8-hch@lst.de
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While we really should be killing the block layer bounce buffering ASAP, I
even more urgently need to stop the drivers to fiddle with the limits from
->slave_configure. Add a no_highmem flag to the Scsi_Host to centralize
this setting and switch the remaining four drivers that use block layer
bounce buffering to it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20240409143748.980206-7-hch@lst.de
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use gpiod_set_value_cansleep() to support gpiochips which can
sleep like, e.g. I2C GPIO expanders.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240409190910.4707-1-francesco@dolcini.it
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Newer Qualcomm platforms (sm8450+) successfully handle busy state and
send the Command Completion after sending the Busy state. Older devices
have firmware bug and can not continue after sending the CCI_BUSY state,
but the command that leads to CCI_BUSY is already forbidden by the
NO_PARTNER_PDOS quirk.
Follow other UCSI glue drivers and drop special handling for CCI_BUSY
event. Let the UCSI core properly handle this state.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240408-qcom-ucsi-fixes-bis-v1-3-716c145ca4b1@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Qualcomm SM8550 (and via a fallback compat SM8650) firmware properly
handles the GET_PDOS command, it sends the CCI_BUSY notification,
and then follows with the CCI_COMMAND_COMPLETE event. Stop using the quirk
for those two platforms.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240408-qcom-ucsi-fixes-bis-v1-2-716c145ca4b1@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PPM might take time to process a reset. Allow 20ms for the reset to
be processed before reading the CCI.
This should not slow down existing implementations because they would
not set any bits in the CCI after a reset, and would take a 20ms delay
to read the CCI anyway. This change makes the delay explicit, and
reduces a CCI read. Based on the spec, the PPM has 10ms to set busy, so,
20ms seems like a reasonable delay before we read the CCI.
Signed-off-by: Pavan Holla <pholla@chromium.org>
Reviewed-by: Prashant Malani <pmalani@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240409-ucsi-reset-delay-v3-1-8440710b012b@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Lenovo Yoga Tablet 2 Pro 1380 model is the exception to the rule that
devices which use the Crystal Cove PMIC without using ACPI for battery and
AC power_supply class support use the USB-phy for charger detection.
Unlike the Lenovo Yoga Tablet 2 830 / 1050 models this model has an extra
LC824206XA Micro USB switch which does the charger detection.
Add a DMI quirk to not set the "linux,phy_charger_detect" property on
the 1380 model. This quirk matches on the BIOS version to differentiate
the 1380 model from the 830 and 1050 models which otherwise have
the same DMI strings.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240406140127.17885-1-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function ci_usb_phy_init is already handling the
hw_phymode_configure path which is also only possible after we have
a valid phy. So we move the ci_ulpi_init after the phy initialization
to be really sure to be able to communicate with the ulpi phy.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20240328-chipidea-phy-misc-v1-1-907d9de5d4df@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After pulling the reset pin some phys are not immediately ready. We add
a short delay of at least 10 ms to ensure that the phy can be properly
used.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20240402-phy-misc-v1-1-de5c17f93f17@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ChipID bytes are read in inverse order: invert the ChipID value
defined as IT5205FN_CHIP_ID and used for validating the same.
Fixes: 41fe9ea169 ("usb: typec: mux: Add ITE IT5205 Alternate Mode Passive MUX driver")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240409113646.305105-1-angelogioacchino.delregno@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
fsl_ep_queue() is only called by usb_ep_queue() (as ep->ops->queue()).
So _ep isn't NULL.
As ep->ops->queue = fsl_ep_queue, the ep was initialized by
struct_ep_setup() and so ep->udc isn't NULL either.
Drop the check for _ep being NULL and assign udc earlier to prevent
following an uninitialized pointer in the two dev_vdbg()s in lines 878
and 882. This fixes a compiler warning when using clang and
CONFIG_USB_GADGET_VERBOSE=y.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202404050227.TTvcCPBu-lkp@intel.com/
Fixes: 6025f20f16 ("usb: gadget: fsl-udc: Replace custom log wrappers by dev_{err,warn,dbg,vdbg}")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20240405055812.694123-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The incompatible device in my possession has a sticker that says
"F5U002 Rev 2" and "P80453-B", and lsusb identifies it as
"050d:0002 Belkin Components IEEE-1284 Controller". There is a bug
report from 2007 from Michael Trausch who was seeing the exact same
errors that I saw in 2024 trying to use this cable.
Link: https://lore.kernel.org/all/46DE5830.9060401@trausch.us/
Signed-off-by: Alex Henrie <alexhenrie24@gmail.com>
Link: https://lore.kernel.org/r/20240326150723.99939-5-alexhenrie24@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This device is a gray USB parallel port adapter with "F5U002" imprinted
on the plastic and a sticker that says both "F5U002" and "P80453-A".
It's identified in lsusb as "05ab:1001 In-System Design BAYI Printer
Class Support". It's subtly different from the other gray cable I have
that has "F5U002 Rev 2" and "P80453-B" on its sticker and device ID
050d:0002.
The uss720 driver appears to work flawlessly with this device, although
the device evidently does not support ECP.
Signed-off-by: Alex Henrie <alexhenrie24@gmail.com>
Link: https://lore.kernel.org/r/20240326150723.99939-4-alexhenrie24@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This avoids a "fix this legacy no-device port driver" warning from
parport_announce_port in drivers/parport/share.c. The parport driver now
requires a pointer to the device struct.
Signed-off-by: Alex Henrie <alexhenrie24@gmail.com>
Acked-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Link: https://lore.kernel.org/r/20240326150723.99939-2-alexhenrie24@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Dell quirk from ucsi_acpi.c. The quirk is no longer
necessary as we no longer send lone connector change acks.
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240327224554.1772525-4-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some PPM implementation do not like UCSI_ACK_CONNECTOR_CHANGE
without UCSI_ACK_COMMAND_COMPLETE. Moreover, doing this is racy
as it requires sending two UCSI_ACK_CC_CI commands in a row and
the second one will be started with UCSI_CCI_ACK_COMPLETE already
set in CCI.
Bundle the UCSI_ACK_CONNECTOR_CHANGE with the UCSI_ACK_COMMAND_COMPLETE
for the UCSI_GET_CONNECTOR_STATUS command that is sent while
handling a connector change event.
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240327224554.1772525-3-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In ucsi.h there are flag definitions for the ->flags field
in struct ucsi. Some implementations abuse these bits for
their private ->flags fields e.g. in struct ucsi_acpi.
Move the definitions into the backend implementations that
still need them. While there fix one instance where the flag
name was not converted in a previous change.
No semantic change intended.
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240327224554.1772525-2-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to adding more quirks, extract quirks to the static
variables and reference them through match->data. Otherwise adding
more quirks will add the table really cumbersome.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240329-qcom-ucsi-fixes-v2-8-0f5d37ed04db@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Qualcomm firmware doesn't return sane information for device's PDOs
unless the partner is also using a PD mode. On SC8280XP this even
results in the Error bit being set in the UCSI response (with 0 error
status).
Add a quirk to delay reading USB PD capabilities for a device until we
detect a partner in PD mode.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240329-qcom-ucsi-fixes-v2-7-0f5d37ed04db@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Extract function to read PDOs from the port and set PD capabilities
accordingly.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240329-qcom-ucsi-fixes-v2-6-0f5d37ed04db@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In a way similar to the previous commit, move
typec_partner_set_usb_power_delivery() to be called after reading the PD
caps. This also removes calls to
usb_power_delivery_unregister_capabilities() from the error path. Keep
all capabilities registered until they are cleared by
ucsi_unregister_partner_pdos().
Fixes: b04e1747fb ("usb: typec: ucsi: Register USB Power Delivery Capabilities")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240329-qcom-ucsi-fixes-v2-5-0f5d37ed04db@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UCSI driver will attempt to set a USB PD device only if it was able to
read PDOs from the firmware. This results in suboptimal behaviour, since
the PD device will be created anyway. Move calls to
typec_port_set_usb_power_delivery() out of conditional code and call it
after reading capabilities.
Fixes: b04e1747fb ("usb: typec: ucsi: Register USB Power Delivery Capabilities")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240329-qcom-ucsi-fixes-v2-4-0f5d37ed04db@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use typec_partner_usb_power_delivery_register() to register PD device
for Type-C partner so that the PD device is nested under the partner's
device in sysfs.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240329-qcom-ucsi-fixes-v2-3-0f5d37ed04db@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reading Partner Source PDOs for the consumer Connectors appears to be
working. Permit getting PDOs in this case in order to populate
capabilities of the connected power supply in the sysfs.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240329-qcom-ucsi-fixes-v2-2-0f5d37ed04db@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The name and description of the USB_NO_PARTNER_PDOS quirk specifies that
only retrieving PDOS of the attached device is crashing. Retrieving PDOS
of the UCSI device works. Fix the condition to limit the workaround only
to is_partner cases.
Fixes: 1d103d6af2 ("usb: typec: ucsi: fix UCSI on buggy Qualcomm devices")
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240329-qcom-ucsi-fixes-v2-1-0f5d37ed04db@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Core in typec_altmode_register_driver() already sets the .owner, so
driver does not need to.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240331091737.19836-3-krzk@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Core in typec_altmode_register_driver() already sets the .owner, so
driver does not need to.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240331091737.19836-2-krzk@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Core in platform_driver_register() already sets the .owner, so driver
does not need to.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240331091737.19836-1-krzk@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UCSI specification defines some notifications to be optional for the
PPM to support. From these only enable the ones the PPM informs us are
actually supported.
Signed-off-by: Diogo Ivo <diogo.ivo@tecnico.ulisboa.pt>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/yhz7nq622mbg3rqsyvqz632pc756niagpfbnzayfswhzo7esho@vrdtx5c3hjgx
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver_desc variable is only used in some configurations:
drivers/usb/gadget/udc/omap_udc.c:113:19: error: unused variable 'driver_desc' [-Werror,-Wunused-const-variable]
Since there is only ever one user of it, just open-code the string in place
and remove the global variable and the macro behind it. This also helps
grep for the MODULE_DESCRIPTION string.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20240403080702.3509288-26-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_DRM_AUX_BRIDGE depends on CONFIG_OF but that dependency is not
included when CONFIG_TYPEC_MUX_PTN36502 selects it, resulting in a
Kconfig warning when CONFIG_OF is disabled:
WARNING: unmet direct dependencies detected for DRM_AUX_BRIDGE
Depends on [n]: HAS_IOMEM [=y] && DRM_BRIDGE [=y] && OF [=n]
Selected by [m]:
- TYPEC_MUX_PTN36502 [=m] && USB_SUPPORT [=y] && TYPEC [=m] && I2C [=y] && (DRM [=y] || DRM [=y]=n) && DRM_BRIDGE [=y]
Only select CONFIG_DRM_AUX_BRIDGE when CONFIG_DRM_BRIDGE and CONFIG_OF
are enabled to clear up the warning. This results in no functional
change because prior to the refactoring that introduces this warning,
ptn36502_register_bridge() returned 0 when CONFIG_OF was disabled, which
continues to occur with drm_aux_bridge_register() when
CONFIG_DRM_AUX_BRIDGE is not enabled.
Fixes: 9dc28ea21e ("usb: typec: ptn36502: switch to DRM_AUX_BRIDGE")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20240328-fix-ptn36502-drm_aux_bridge-select-v1-1-85552117e26e@kernel.org
Link: https://lore.kernel.org/r/20240404123534.2708591-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SanDisks USB3 storage may disapper after system reboot:
usb usb2-port3: link state change
xhci_hcd 0000:00:14.0: clear port3 link state change, portsc: 0x2c0
usb usb2-port3: do warm reset, port only
xhci_hcd 0000:00:14.0: xhci_hub_status_data: stopping usb2 port polling
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x2b0, return 0x2b0
usb usb2-port3: not warm reset yet, waiting 50ms
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x2f0, return 0x2f0
usb usb2-port3: not warm reset yet, waiting 200ms
...
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x6802c0, return 0x7002c0
usb usb2-port3: not warm reset yet, waiting 200ms
xhci_hcd 0000:00:14.0: clear port3 reset change, portsc: 0x4802c0
xhci_hcd 0000:00:14.0: clear port3 warm(BH) reset change, portsc: 0x4002c0
xhci_hcd 0000:00:14.0: clear port3 link state change, portsc: 0x2c0
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x2c0, return 0x2c0
usb usb2-port3: not enabled, trying warm reset again...
This is due to the USB device still cause port change event after xHCI is
shuted down:
xhci_hcd 0000:38:00.0: // Setting command ring address to 0xffffe001
xhci_hcd 0000:38:00.0: xhci_resume: starting usb3 port polling.
xhci_hcd 0000:38:00.0: xhci_hub_status_data: stopping usb4 port polling
xhci_hcd 0000:38:00.0: xhci_hub_status_data: stopping usb3 port polling
xhci_hcd 0000:38:00.0: hcd_pci_runtime_resume: 0
xhci_hcd 0000:38:00.0: xhci_shutdown: stopping usb3 port polling.
xhci_hcd 0000:38:00.0: // Halt the HC
xhci_hcd 0000:38:00.0: xhci_shutdown completed - status = 1
xhci_hcd 0000:00:14.0: xhci_shutdown: stopping usb1 port polling.
xhci_hcd 0000:00:14.0: // Halt the HC
xhci_hcd 0000:00:14.0: xhci_shutdown completed - status = 1
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x1203, return 0x203
xhci_hcd 0000:00:14.0: set port reset, actual port 2-3 status = 0x1311
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x201203, return 0x100203
xhci_hcd 0000:00:14.0: clear port3 reset change, portsc: 0x1203
xhci_hcd 0000:00:14.0: clear port3 warm(BH) reset change, portsc: 0x1203
xhci_hcd 0000:00:14.0: clear port3 link state change, portsc: 0x1203
xhci_hcd 0000:00:14.0: clear port3 connect change, portsc: 0x1203
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x1203, return 0x203
usb 2-3: device not accepting address 2, error -108
xhci_hcd 0000:00:14.0: xHCI dying or halted, can't queue_command
xhci_hcd 0000:00:14.0: Set port 2-3 link state, portsc: 0x1203, write 0x11261
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x1263, return 0x263
xhci_hcd 0000:00:14.0: set port reset, actual port 2-3 status = 0x1271
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x12b1, return 0x2b1
usb usb2-port3: not reset yet, waiting 60ms
ACPI: PM: Preparing to enter system sleep state S5
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x12f1, return 0x2f1
usb usb2-port3: not reset yet, waiting 200ms
reboot: Restarting system
The port change event is caused by LPM transition, so disabling LPM at shutdown
to make sure the device is in U0 for warmboot.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20240305065140.66801-1-kai.heng.feng@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When ncm function is working and then stop usb0 interface for link down,
eth_stop() is called. At this piont, accidentally if usb transport error
should happen in usb_ep_enable(), 'in_ep' and/or 'out_ep' may not be enabled.
After that, ncm_disable() is called to disable for ncm unbind
but gether_disconnect() is never called since 'in_ep' is not enabled.
As the result, ncm object is released in ncm unbind
but 'dev->port_usb' associated to 'ncm->port' is not NULL.
And when ncm bind again to recover netdev, ncm object is reallocated
but usb0 interface is already associated to previous released ncm object.
Therefore, once usb0 interface is up and eth_start_xmit() is called,
released ncm object is dereferrenced and it might cause use-after-free memory.
[function unlink via configfs]
usb0: eth_stop dev->port_usb=ffffff9b179c3200
--> error happens in usb_ep_enable().
NCM: ncm_disable: ncm=ffffff9b179c3200
--> no gether_disconnect() since ncm->port.in_ep->enabled is false.
NCM: ncm_unbind: ncm unbind ncm=ffffff9b179c3200
NCM: ncm_free: ncm free ncm=ffffff9b179c3200 <-- released ncm
[function link via configfs]
NCM: ncm_alloc: ncm alloc ncm=ffffff9ac4f8a000
NCM: ncm_bind: ncm bind ncm=ffffff9ac4f8a000
NCM: ncm_set_alt: ncm=ffffff9ac4f8a000 alt=0
usb0: eth_open dev->port_usb=ffffff9b179c3200 <-- previous released ncm
usb0: eth_start dev->port_usb=ffffff9b179c3200 <--
eth_start_xmit()
--> dev->wrap()
Unable to handle kernel paging request at virtual address dead00000000014f
This patch addresses the issue by checking if 'ncm->netdev' is not NULL at
ncm_disable() to call gether_disconnect() to deassociate 'dev->port_usb'.
It's more reasonable to check 'ncm->netdev' to call gether_connect/disconnect
rather than check 'ncm->port.in_ep->enabled' since it might not be enabled
but the gether connection might be established.
Signed-off-by: Norihiko Hama <Norihiko.Hama@alpsalpine.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20240327023550.51214-1-Norihiko.Hama@alpsalpine.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Off-by-one errors happen because nr_snk_pdo and nr_src_pdo are
incorrectly added one. The index of the loop is equal to the number of
PDOs to be updated when leaving the loop and it doesn't need to be added
one.
When doing the power negotiation, TCPM relies on the "nr_snk_pdo" as
the size of the local sink PDO array to match the Source capabilities
of the partner port. If the off-by-one overflow occurs, a wrong RDO
might be sent and unexpected power transfer might happen such as over
voltage or over current (than expected).
"nr_src_pdo" is used to set the Rp level when the port is in Source
role. It is also the array size of the local Source capabilities when
filling up the buffer which will be sent as the Source PDOs (such as
in Power Negotiation). If the off-by-one overflow occurs, a wrong Rp
level might be set and wrong Source PDOs will be sent to the partner
port. This could potentially cause over current or port resets.
Fixes: cd099cde4e ("usb: typec: tcpm: Support multiple capabilities")
Cc: stable@vger.kernel.org
Signed-off-by: Kyle Tso <kyletso@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240404133517.2707955-1-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of bailing when fences have already been installed on the
DMABUF, wait for them (with a timeout) when doing a blocking operation.
This fixes the issue where userspace would submit a DMABUF with fences
already installed, with the (correct) expectation that it would just
work.
Fixes: 7b07a2a7ca ("usb: gadget: functionfs: Add DMABUF import interface")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20240402110951.16376-3-paul@crapouillou.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A "read" fence was installed when the DMABUF was to be written to,
and a "write" fence was installed when the DMABUF was to be read from.
Besides, dma_resv_usage_rw() should only be used when waiting for
fences.
Fixes: 7b07a2a7ca ("usb: gadget: functionfs: Add DMABUF import interface")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20240402110951.16376-2-paul@crapouillou.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix issues when initially checking for a connector change:
- Use the correct connector number not the entire CCI.
- Call ->read under the PPM lock.
- Remove a bogus READ_ONCE.
Fixes: 808a8b9e0b ("usb: typec: ucsi: Check for notifications after init")
Cc: stable@kernel.org
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240401210515.1902048-1-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pointer from a xhci usb virt device to its root hub port
(vdev->rhub_port) is set later when device is addressed, not while
vdev is allocated.
Tracepoints dereferenced this rhub_port pointer when freeing the virt
device, which causes null pointer dereference if tracing is enabled
and device is freed before addressed.
This can happen if tracing is enabled and xhci driver is unloaded before
a device is fully enumerated, or initial enumeration fails and device
is reset and freed before retry.
Don't dereference the rhub_port or show port numbers when tracing
xhci_free_virt_device(). This info is not very useful anyway.
Print the more useful slot id instead
Fixes: 06790c1908 ("xhci: replace real & fake port with pointer to root hub port")
Reported-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Closes: https://lore.kernel.org/linux-usb/20240402005007.klv2ij727fkz7rpd@synopsys.com/
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240404121106.2842417-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we get STS_HCE we give up on the interrupt, but for the purpose
of IRQ handling that still counts as ours. We may return IRQ_NONE
only if we are positive that it wasn't ours. Hence correct the default.
Fixes: 2a25e66d67 ("xhci: print warning when HCE was set")
Cc: stable@vger.kernel.org # v6.2+
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240404121106.2842417-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The XMOS XVF3500 VocalFusion Voice Processor[1] is a low-latency, 32-bit
multicore controller for voice processing.
This device requires a specific power sequence, which consists of
enabling the regulators that control the 3V3 and 1V0 device supplies,
and a reset de-assertion after a delay of at least 100ns.
Once in normal operation, the XVF3500 registers itself as a USB device,
and it does not require any device-specific operations in the driver.
[1] https://www.xmos.com/xvf3500/
Acked-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Javier Carrasco <javier.carrasco@wolfvision.net>
Link: https://lore.kernel.org/r/20240325-onboard_xvf3500-v8-8-29e3f9222922@wolfvision.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Most of the functionality this driver provides can be used by non-hub
devices as well.
To account for the hub-specific code, add a flag to the device data
structure and check its value for hub-specific code.
The 'always_powered_in_supend' attribute is only available for hub
devices, keeping the driver's default behavior for non-hub devices (keep
on in suspend).
Acked-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Javier Carrasco <javier.carrasco@wolfvision.net>
Link: https://lore.kernel.org/r/20240325-onboard_xvf3500-v8-6-29e3f9222922@wolfvision.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch prepares onboad_hub to support non-hub devices by renaming
the driver files and their content, the headers and their references.
The comments and descriptions have been slightly modified to keep
coherence and account for the specific cases that only affect onboard
hubs (e.g. peer-hub).
The "hub" variables in functions where "dev" (and similar names) variables
already exist have been renamed to onboard_dev for clarity, which adds a
few lines in cases where more than 80 characters are used.
No new functionality has been added.
Acked-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Javier Carrasco <javier.carrasco@wolfvision.net>
Link: https://lore.kernel.org/r/20240325-onboard_xvf3500-v8-2-29e3f9222922@wolfvision.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current implementation uses generic names for the power supplies,
which conflicts with proper name definitions in the device bindings.
Add a per-device property to include real supply names and keep generic
names for existing devices to keep backward compatibility.
Acked-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Javier Carrasco <javier.carrasco@wolfvision.net>
Link: https://lore.kernel.org/r/20240325-onboard_xvf3500-v8-1-29e3f9222922@wolfvision.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dt-bindings is going to use "usb_wakeup" as wakup clock name. This will
align the change with dt-bindings.
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20240321081439.541799-11-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the trailing comma in the terminator entry for the OF table
making code robust against (theoretical) misrebases or other similar
things where the new entry goes _after_ the termination without the
compiler noticing.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240319105356.87287-6-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The RZ/G2L family SoCs has 10 pipe buffers compared to 16 pipe buffers on
RZ/A2M. Update the pipe configuration for RZ/G2L family SoCs and use
family SoC specific compatible to handle this difference.
The pipe configuration of RZ/G2L is same as usbhsc_rzg2l_default_pipe[],
so select the default pipe configuration for RZ/G2L SoCs by setting
.has_new_pipe_configs to zero.
Add SoC specific compatible to OF table to avoid ABI breakage with old
DTB. To optimize memory usage the SoC specific compatible will be removed
later.
Based on the patch in BSP by Huy Nguyen <huy.nguyen.wh@renesas.com>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240319105356.87287-5-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per the hardware manual, double buffer setting results in fewer
interrupts for high-speed data transfers. Improve usbhsc_default_pipe[]
for isochronous transfers by updating the table from single->double
buffering and update the pipe number accordingly.
Suggested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240319105356.87287-4-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The show and store callback routines for the "disable" sysfs attribute
file in port.c acquire the device lock for the port's parent hub
device. This can cause problems if another process has locked the hub
to remove it or change its configuration:
Removing the hub or changing its configuration requires the
hub interface to be removed, which requires the port device
to be removed, and device_del() waits until all outstanding
sysfs attribute callbacks for the ports have returned. The
lock can't be released until then.
But the disable_show() or disable_store() routine can't return
until after it has acquired the lock.
The resulting deadlock can be avoided by calling
sysfs_break_active_protection(). This will cause the sysfs core not
to wait for the attribute's callback routine to return, allowing the
removal to proceed. The disadvantage is that after making this call,
there is no guarantee that the hub structure won't be deallocated at
any moment. To prevent this, we have to acquire a reference to it
first by calling hub_get().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/f7a8c135-a495-4ce6-bd49-405a45e7ea9a@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Create hub_get() and hub_put() routines to encapsulate the kref_get()
and kref_put() calls in hub.c. The new routines will be used by the
next patch in this series.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/604da420-ae8a-4a9e-91a4-2d511ff404fb@rowland.harvard.edu
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check the UCSI_CAP_GET_PD_MESSAGE bit before sending GET_PD_MESSAGE to
discover partner and cable identity, check UCSI_CAP_CABLE_DETAILS before
sending GET_CABLE_PROPERTY to discover the cable and check
UCSI_CAP_ALT_MODE_DETAILS before registering the a cable plug. Additionally,
move 8 bits from reserved_1 to features in the ucsi_capability struct. This
makes the field 16 bits, still 8 short of the 24 bits allocated for it in
UCSI v3.0, but it will not overflow because UCSI only defines 14 bits in
bmOptionalFeatures.
Fixes: 38ca416597 ("usb: typec: ucsi: Register cables based on GET_CABLE_PROPERTY")
Link: https://lore.kernel.org/linux-usb/44e8142f-d9b3-487b-83fe-39deadddb492@linaro.org
Suggested-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Jameson Thies <jthies@google.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Reviewed-by: Benson Leung <bleung@chromium.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240315171836.343830-2-jthies@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check the UCSI_CCI_RESET_COMPLETE complete flag before starting
another reset. Use a UCSI_SET_NOTIFICATION_ENABLE command to clear
the flag if it is set.
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Cc: stable <stable@kernel.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Link: https://lore.kernel.org/r/20240320073927.1641788-6-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some DELL systems don't like UCSI_ACK_CC_CI commands with the
UCSI_ACK_CONNECTOR_CHANGE but not the UCSI_ACK_COMMAND_COMPLETE
bit set. The current quirk still leaves room for races because
it requires two consecutive ACK commands to be sent.
Refactor and significantly simplify the quirk to fix this:
Send a dummy command and bundle the connector change ack with the
command completion ack in a single UCSI_ACK_CC_CI command.
This removes the need to probe for the quirk.
While there define flag bits for struct ucsi_acpi->flags in ucsi_acpi.c
and don't re-use definitions from ucsi.h for struct ucsi->flags.
Fixes: f3be347ea4 ("usb: ucsi_acpi: Quirk to ack a connector change ack cmd")
Cc: stable@vger.kernel.org
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Link: https://lore.kernel.org/r/20240320073927.1641788-5-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a command completes the OPM must send an ack. This applies
to unsupported commands, too.
Send the required ACK for unsupported commands.
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Cc: stable <stable@kernel.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Link: https://lore.kernel.org/r/20240320073927.1641788-4-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The completion notification for the final SET_NOTIFICATION_ENABLE
command during initialization can include a connector change
notification. However, at the time this completion notification is
processed, the ucsi struct is not ready to handle this notification.
As a result the notification is ignored and the controller
never sends an interrupt again.
Re-check CCI for a pending connector state change after
initialization is complete. Adjust the corresponding debug
message accordingly.
Fixes: 71a1fa0df2 ("usb: typec: ucsi: Store the notification mask")
Cc: stable@vger.kernel.org
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Link: https://lore.kernel.org/r/20240320073927.1641788-3-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suppose we sleep on the PPM lock after clearing the EVENT_PENDING
bit because the thread for another connector is executing a command.
In this case the command completion of the other command will still
report the connector change for our connector.
Clear the EVENT_PENDING bit under the PPM lock to avoid another
useless call to ucsi_handle_connector_change() in this case.
Fixes: c9aed03a0a ("usb: ucsi: Add missing ppm_lock")
Cc: stable <stable@kernel.org>
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Link: https://lore.kernel.org/r/20240320073927.1641788-2-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The attribute writing should return the number of bytes used from the
buffer on success.
Fixes: a7cff92f06 ("usb: typec: USB Power Delivery helpers for ports and partners")
Cc: stable@vger.kernel.org
Signed-off-by: Kyle Tso <kyletso@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240319074309.3306579-1-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is possible trigger below warning message from mass storage function,
WARNING: CPU: 6 PID: 3839 at drivers/usb/gadget/udc/core.c:294 usb_ep_queue+0x7c/0x104
pc : usb_ep_queue+0x7c/0x104
lr : fsg_main_thread+0x494/0x1b3c
Root cause is mass storage function try to queue request from main thread,
but other thread may already disable ep when function disable.
As there is no function failure in the driver, in order to avoid effort
to fix warning, change WARN_ON_ONCE() in usb_ep_queue() to pr_debug().
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable@vger.kernel.org
Signed-off-by: yuan linyu <yuanlinyu@hihonor.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20240315020144.2715575-1-yuanlinyu@hihonor.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel Arrow Lake CPU uses the Meteor Lake ID with this
controller (the controller that's part of the Intel Arrow
Lake chipset (PCH) does still have unique PCI ID).
Fixes: de4b5b28c8 ("usb: dwc3: pci: add support for the Intel Arrow Lake-H")
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240312115008.1748637-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the device is configured for system wakeup, then make sure that the
xHCI driver knows about it and make sure to permit wakeup only at the
appropriate time.
For host mode, if the controller goes through the dwc3 code path, then a
child xHCI platform device is created. Make sure the platform device
also inherits the wakeup setting for xHCI to enable remote wakeup.
For device mode, make sure to disable system wakeup if no gadget driver
is bound. We may experience unwanted system wakeup due to the wakeup
signal from the controller PMU detecting connection/disconnection when
in low power (D3). E.g. In the case of Steam Deck, the PCI PME prevents
the system staying in suspend.
Cc: stable@vger.kernel.org
Reported-by: Guilherme G. Piccoli <gpiccoli@igalia.com>
Closes: https://lore.kernel.org/linux-usb/70a7692d-647c-9be7-00a6-06fc60f77294@igalia.com/T/#mf00d6669c2eff7b308d1162acd1d66c09f0853c7
Fixes: d07e8819a0 ("usb: dwc3: add xHCI Host support")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Tested-by: Sanath S <Sanath.S@amd.com>
Tested-by: Guilherme G. Piccoli <gpiccoli@igalia.com> # Steam Deck
Link: https://lore.kernel.org/r/667cfda7009b502e08462c8fb3f65841d103cc0a.1709865476.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 75fd6485cc.
This patch was applied twice by accident, causing probe failures.
Revert the accident.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Fixes: 75fd6485cc ("usb: phy: generic: Get the vbus supply")
Cc: stable <stable@kernel.org>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/20240314092628.1869414-1-alexander.stein@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
wdm_read() cannot race with itself. However, in
service_outstanding_interrupt() it can race with the
workqueue, which can be triggered by error handling.
Hence we need to make sure that the WDM_RESPONDING
flag is not just only set but tested.
Fixes: afba937e54 ("USB: CDC WDM driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20240314115132.3907-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Among the attribute file callback routines in
drivers/usb/core/sysfs.c, the interface_authorized_store() function is
the only one which acquires a device lock on an ancestor device: It
calls usb_deauthorize_interface(), which locks the interface's parent
USB device.
The will lead to deadlock if another process already owns that lock
and tries to remove the interface, whether through a configuration
change or because the device has been disconnected. As part of the
removal procedure, device_del() waits for all ongoing sysfs attribute
callbacks to complete. But usb_deauthorize_interface() can't complete
until the device lock has been released, and the lock won't be
released until the removal has finished.
The mechanism provided by sysfs to prevent this kind of deadlock is
to use the sysfs_break_active_protection() function, which tells sysfs
not to wait for the attribute callback.
Reported-and-tested by: Yue Sun <samsun1006219@gmail.com>
Reported by: xingwei lee <xrivendell7@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/linux-usb/CAEkJfYO6jRVC8Tfrd_R=cjO0hguhrV31fDPrLrNOOHocDkPoAA@mail.gmail.com/#r
Fixes: 310d2b4124 ("usb: interface authorization: SysFS part of USB interface authorization")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1c37eea1-9f56-4534-b9d8-b443438dc869@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PD of Type-C port needs to be updated in pd_set. Unlink the Type-C
port device to the old PD before linking it to a new one.
Fixes: cd099cde4e ("usb: typec: tcpm: Support multiple capabilities")
Cc: stable@vger.kernel.org
Signed-off-by: Kyle Tso <kyletso@google.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240311172306.3911309-1-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When unregister pd capabilitie in tcpm, KASAN will capture below double
-free issue. The root cause is the same capabilitiy will be kfreed twice,
the first time is kfreed by pd_capabilities_release() and the second time
is explicitly kfreed by tcpm_port_unregister_pd().
[ 3.988059] BUG: KASAN: double-free in tcpm_port_unregister_pd+0x1a4/0x3dc
[ 3.995001] Free of addr ffff0008164d3000 by task kworker/u16:0/10
[ 4.001206]
[ 4.002712] CPU: 2 PID: 10 Comm: kworker/u16:0 Not tainted 6.8.0-rc5-next-20240220-05616-g52728c567a55 #53
[ 4.012402] Hardware name: Freescale i.MX8QXP MEK (DT)
[ 4.017569] Workqueue: events_unbound deferred_probe_work_func
[ 4.023456] Call trace:
[ 4.025920] dump_backtrace+0x94/0xec
[ 4.029629] show_stack+0x18/0x24
[ 4.032974] dump_stack_lvl+0x78/0x90
[ 4.036675] print_report+0xfc/0x5c0
[ 4.040289] kasan_report_invalid_free+0xa0/0xc0
[ 4.044937] __kasan_slab_free+0x124/0x154
[ 4.049072] kfree+0xb4/0x1e8
[ 4.052069] tcpm_port_unregister_pd+0x1a4/0x3dc
[ 4.056725] tcpm_register_port+0x1dd0/0x2558
[ 4.061121] tcpci_register_port+0x420/0x71c
[ 4.065430] tcpci_probe+0x118/0x2e0
To fix the issue, this will remove kree() from tcpm_port_unregister_pd().
Fixes: cd099cde4e ("usb: typec: tcpm: Support multiple capabilities")
cc: stable@vger.kernel.org
Suggested-by: Aisheng Dong <aisheng.dong@nxp.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240311065219.777037-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When auxiliary_device_add() returns error and then calls
auxiliary_device_uninit(), callback function ljca_auxdev_release
calls kfree(auxdev->dev.platform_data) to free the parameter data
of the function ljca_new_client_device. The callers of
ljca_new_client_device shouldn't call kfree() again
in the error handling path to free the platform data.
Fix this by cleaning up the redundant kfree() in all callers and
adding kfree() the passed in platform_data on errors which happen
before auxiliary_device_init() succeeds .
Fixes: acd6199f19 ("usb: Add support for Intel LJCA device")
Cc: stable <stable@kernel.org>
Signed-off-by: Yongzhi Liu <hyperlyzcs@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240311125748.28198-1-hyperlyzcs@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When orientation switch is enabled in ucsi glink, there is a xhci
probe failure seen when booting up in host mode in reverse
orientation.
During bootup the following things happen in multiple drivers:
a) DWC3 controller driver initializes the core in device mode when the
dr_mode is set to DRD. It relies on role_switch call to change role to
host.
b) QMP driver initializes the lanes to TYPEC_ORIENTATION_NORMAL as a
normal routine. It relies on the typec_switch_set call to get notified
of orientation changes.
c) UCSI core reads the UCSI_GET_CONNECTOR_STATUS via the glink and
provides initial role switch to dwc3 controller.
When booting up in host mode with orientation TYPEC_ORIENTATION_REVERSE,
then we see the following things happening in order:
a) UCSI gives initial role as host to dwc3 controller ucsi_register_port.
Upon receiving this notification, the dwc3 core needs to program GCTL from
PRTCAP_DEVICE to PRTCAP_HOST and as part of this change, it asserts GCTL
Core soft reset and waits for it to be completed before shifting it to
host. Only after the reset is done will the dwc3_host_init be invoked and
xhci is probed. DWC3 controller expects that the usb phy's are stable
during this process i.e., the phy init is already done.
b) During the 100ms wait for GCTL core soft reset, the actual notification
from PPM is received by ucsi_glink via pmic glink for changing role to
host. The pmic_glink_ucsi_notify routine first sends the orientation
change to QMP and then sends role to dwc3 via ucsi framework. This is
happening exactly at the time GCTL core soft reset is being processed.
c) When QMP driver receives typec switch to TYPEC_ORIENTATION_REVERSE, it
then re-programs the phy at the instant GCTL core soft reset has been
asserted by dwc3 controller due to which the QMP PLL lock fails in
qmp_combo_usb_power_on.
d) After the 100ms of GCTL core soft reset is completed, the dwc3 core
goes for initializing the host mode and invokes xhci probe. But at this
point the QMP is non-responsive and as a result, the xhci plat probe fails
during xhci_reset.
Fix this by passing orientation switch to available ucsi instances if
their gpio configuration is available before ucsi_register is invoked so
that by the time, the pmic_glink_ucsi_notify provides typec_switch to QMP,
the lane is already configured and the call would be a NOP thus not racing
with role switch.
Cc: stable@vger.kernel.org
Fixes: c6165ed2f4 ("usb: ucsi: glink: use the connector orientation GPIO to provide switch events")
Suggested-by: Wesley Cheng <quic_wcheng@quicinc.com>
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240301040914.458492-1-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In tcpm_pd_set, the array of port source capabilities is port->src_pdo,
not port->snk_pdo.
Fixes: cd099cde4e ("usb: typec: tcpm: Support multiple capabilities")
Cc: stable@vger.kernel.org
Signed-off-by: Kyle Tso <kyletso@google.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240311144500.3694849-1-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the scenario of entering hibernation with udisk in the system, if the
udisk was gone or resume fail in the thaw phase of hibernation. Its state
will be set to NOTATTACHED. At this point, usb_hub_wq was already freezed
and can't not handle disconnect event. Next, in the poweroff phase of
hibernation, SYNCHRONIZE_CACHE SCSI command will be sent to this udisk
when poweroff this scsi device, which will cause uas_submit_urbs to be
called to submit URB for sense/data/cmd pipe. However, these URBs will
submit fail as device was set to NOTATTACHED state. Then, uas_submit_urbs
will return a value SCSI_MLQUEUE_DEVICE_BUSY to the caller. That will lead
the SCSI layer go into an ugly loop and system fail to go into hibernation.
On the other hand, when we specially check for -ENODEV in function
uas_queuecommand_lck, returning DID_ERROR to SCSI layer will cause device
poweroff fail and system shutdown instead of entering hibernation.
To fix this issue, let uas_submit_urbs to return original generic error
when submitting URB failed. At the same time, we need to translate -ENODEV
to DID_NOT_CONNECT for the SCSI layer.
Suggested-by: Oliver Neukum <oneukum@suse.com>
Cc: stable@vger.kernel.org
Signed-off-by: Weitao Wang <WeitaoWang-oc@zhaoxin.com>
Link: https://lore.kernel.org/r/20240306180814.4897-1-WeitaoWang-oc@zhaoxin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The size given to strscpy() is not consistent with the destination buffer
that is used. The size is related to 'driver' and the buffer is
'mixername'.
sizeof(card->mixername) is 80 and sizeof(card->driver) is 16, so in
theory this could lead to unneeded string truncation.
In practice, this is not the case because g_audio_setup() has only 2
callers. 'card_name' is either "UAC1_Gadget" or "UAC2_Gadget".
Anyway, using the correct size is cleaner and more future proof.
In order to be less verbose, use the new 2-argument version of strscpy()
which computes auto-magically the size of the destination.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/bf8a9353319566624f653531b80e5caf3d346ba1.1711176700.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added new bitfield GRSTCTL_CLOCK_SWITH_TIMER in GRSTCTL register.
This bitfield applicable HSOTG cores v5.00 or higher and not
applicable to HS/FS IOT devices.
This bitfield must be programmed to 3'b010 if core will be
used in Low-speed and core configured for any HS/FS PHY interface.
This bitfield must be programmed to 3'b111 if core configured
to use either:
- HS PHY interface UTMI or ULPI
- FS PHY any interface
Signed-off-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Link: https://lore.kernel.org/r/0616838cfee958774c9321c6eeeda4be92f900d8.1708948356.git.Minas.Harutyunyan@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added programmming of ULPI_LATCH_EN_DURING_HIB_ENTRY bit in GPWRDN
register when using ULPI PHY during entry/exit to/from hibernation.
This bit set to 1 during entering to hibernation if ULPI PHY used.
On exiting from hibernation this bit reset to 0.
Applicable for both host and device modes.
Signed-off-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Link: https://lore.kernel.org/r/e024cb39a7177ec201c873df25ca6365f2e55947.1708948356.git.Minas.Harutyunyan@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added new bit ULPI_LATCH_EN_DURING_HIB_ENTRY in GPWRDN register.
This bit applicable HSOTG cores v5.00 or higher.
Affects Hibernation Entry and Exit sequence (for both Host and Device)
when using ULPI PHY.
Signed-off-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Link: https://lore.kernel.org/r/56d05a4f5750aaa58d8c5bab7705814942a985bd.1708948356.git.Minas.Harutyunyan@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To support eUSB2 PHY disconnect flow required in Soft disconnect
state set GOTGCTL_EUSB2_DISC_SUPP bit, if applicable.
On Session End Detected interrupt clear PCGCTL_GATEHCLK and
PCGCTL_STOPPCLK bits if eusb2_disc parameter true.
Signed-off-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Link: https://lore.kernel.org/r/9d50b83df693cda8c391313e90048df8dd611c04.1708948356.git.Minas.Harutyunyan@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added new parameter eusb2_disc to list of core parameters which specify
whether eUSB2 PHY disconnect support flow applicable or no.
Set to false as default value and checked core version if set to true.
This parameter applicable in device mode of HSOTG and HS IOT cores
v5.00 or higher.
Added print this parameter in show parameters of debugfs.
Signed-off-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Link: https://lore.kernel.org/r/e77cc4312bda797d1ddaa4351d86c65a69c8b926.1708948356.git.Minas.Harutyunyan@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to using the new DRM_AUX_BRIDGE helper to create the transparent
DRM bridge device instead of handcoding corresponding functionality.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240315-ptn36502-aux-v1-1-c9d3c828ff2e@fairphone.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The maple tree register cache is based on a much more modern data structure
than the rbtree cache and makes optimisation choices which are probably
more appropriate for modern systems than those made by the rbtree cache.
Signed-off-by: Bo Liu <liubo03@inspur.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240309071757.3152-1-liubo03@inspur.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Macros with good names offer better readability. Besides, also move
the definition to ehci.h.
Signed-off-by: Dingyan Li <18500469033@163.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20240309033709.14604-1-18500469033@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/91311e53e9432ae84d5720485c3b436fb7f06227.1709886922.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
udc device and gadget device are tightly coupled, yet there's no good
way to corelate the two. Add a sysfs link in udc that points to the
corresponding gadget device.
An example use case: userspace configures a f_midi configfs driver and
bind the udc device, then it tries to locate the corresponding midi
device, which is a child device of the gadget device. The gadget device
that's associated to the udc device has to be identified in order to
index the midi device. Having a sysfs link would make things much
easier.
Signed-off-by: Roy Luo <royluo@google.com>
Link: https://lore.kernel.org/r/20240307030922.3573161-1-royluo@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Apple CarLife iAP gadget has a descriptor in userspace with two
alternate settings. The host sends the set_alt request to configure
alt_setting 0 or 1, and this is verified by the subsequent get_alt
request.
This patch implements and sets the get_alt callback. Without the
get_alt callback, composite.c abruptly concludes the
USB_REQ_GET/SET_INTERFACE request, assuming only one alt setting
for the endpoint.
unlike the uvc and ncm, f_fs gadget is fully implemented in userspace,
and driver just reset the eps and generate the event. so no additional
adaptaion associated with this change is not required in set_alt callback
Signed-off-by: Hardik Gajjar <hgajjar@de.adit-jv.com>
Link: https://lore.kernel.org/r/20240301124708.120394-1-hgajjar@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When setting the guid via configfs it is possible to test if
its value is one of the kernel supported ones by calling
uvc_format_by_guid on it. If the result is NULL, we know the
guid is unsupported and can be ignored.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20240221-uvc-gadget-configfs-guid-v1-1-f0678ca62ebb@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When setting uncompressed formats, the values of bytesperline and
sizeimage can already be determined by using the v4l2_fill_pixfmt helper
function. We change the try_fmt function to use the helper instead.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20240221-uvc-gadget-uncompressed-v1-1-f55e97287cae@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of USB and Thunderbolt changes for 6.9-rc1. Lots of
tiny changes and forward progress to support new hardware and better
support for existing devices. Included in here are:
- Thunderbolt (i.e. USB4) updates for newer hardware and uses as more
people start to use the hardware
- default USB authentication mode Kconfig and documentation update to
make it more obvious what is going on
- USB typec updates and enhancements
- usual dwc3 driver updates
- usual xhci driver updates
- function USB (i.e. gadget) driver updates and additions
- new device ids for lots of drivers
- loads of other small updates, full details in the shortlog
All of these, including a "last minute regression fix" have been in
linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZfwpzA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymS9QCdEuF6KJFLOrDrGS4NbZNSUPIVF6oAn350r4NX
CMZah37Dfr1VDCOOV4gQ
=HACL
-----END PGP SIGNATURE-----
Merge tag 'usb-6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt changes for 6.9-rc1. Lots
of tiny changes and forward progress to support new hardware and
better support for existing devices. Included in here are:
- Thunderbolt (i.e. USB4) updates for newer hardware and uses as more
people start to use the hardware
- default USB authentication mode Kconfig and documentation update to
make it more obvious what is going on
- USB typec updates and enhancements
- usual dwc3 driver updates
- usual xhci driver updates
- function USB (i.e. gadget) driver updates and additions
- new device ids for lots of drivers
- loads of other small updates, full details in the shortlog
All of these, including a "last minute regression fix" have been in
linux-next with no reported issues"
* tag 'usb-6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (185 commits)
usb: usb-acpi: Fix oops due to freeing uninitialized pld pointer
usb: gadget: net2272: Use irqflags in the call to net2272_probe_fin
usb: gadget: tegra-xudc: Fix USB3 PHY retrieval logic
phy: tegra: xusb: Add API to retrieve the port number of phy
USB: gadget: pxa27x_udc: Remove unused of_gpio.h
usb: gadget/snps_udc_plat: Remove unused of_gpio.h
usb: ohci-pxa27x: Remove unused of_gpio.h
usb: sl811-hcd: only defined function checkdone if QUIRK2 is defined
usb: Clarify expected behavior of dev_bin_attrs_are_visible()
xhci: Allow RPM on the USB controller (1022:43f7) by default
usb: isp1760: remove SLAB_MEM_SPREAD flag usage
usb: misc: onboard_hub: use pointer consistently in the probe function
usb: gadget: fsl: Increase size of name buffer for endpoints
usb: gadget: fsl: Add of device table to enable module autoloading
usb: typec: tcpm: add support to set tcpc connector orientatition
usb: typec: tcpci: add generic tcpci fallback compatible
dt-bindings: usb: typec-tcpci: add tcpci fallback binding
usb: gadget: fsl-udc: Replace custom log wrappers by dev_{err,warn,dbg,vdbg}
usb: core: Set connect_type of ports based on DT node
dt-bindings: usb: Add downstream facing ports to realtek binding
...
If reading the ACPI _PLD port location object fails, or the port
doesn't have a _PLD ACPI object then the *pld pointer will remain
uninitialized and oops when freed.
The patch that caused this is currently in next, on its way to v6.9.
So no need to add this to stable or current 6.8 kernel.
Reported-by: Klara Modin <klarasmodin@gmail.com>
Closes: https://lore.kernel.org/linux-usb/7e92369a-3197-4883-9988-3c93452704f5@gmail.com/
Tested-by: Klara Modin <klarasmodin@gmail.com>
Fixes: f3ac348e6e ("usb: usb-acpi: Set port connect type of not connectable ports correctly")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240308113425.1144689-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This release sees some exciting changes from David Lechner which
implements some optimisations that have been talked about for a long
time which allows client drivers to pre-prepare SPI messages for
repeated or low latency use. This lets us move work out of latency
sensitive paths and avoid repeating work for frequently performed
operations. As well as being useful in itself this will also be used in
future to allow controllers to directly trigger SPI operations (eg, from
interrupts).
Otherwise this release has mostly been focused on cleanups, plus a
couple of new devices:
- Support for pre-optimising messages.
- A big set of updates from Uwe Kleine-König moving drivers to use APIs
with more modern terminology for controllers.
- Major overhaul of the s3c64xx driver.
- Support for Google GS101 and Samsung Exynos850.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmXvHx0ACgkQJNaLcl1U
h9ATVQf/WafEp7ddJ23bRaHZx/gBCMgv8N6mN7OBnzB2pMIGL56SPf9fGAmCUQKt
mne6fDg6/RpydG/72TFppUjRFLN9CwoJjJfQIXMgOqYuPaMEnrj1wbcXar3MeeX2
8hS1u7wKwhOuuwLmoqqMOTKyGUj2mHsBOTOo0vm4WM1s9IHhY5TG2clYv1A+KZbj
kSHE5m7YnBLwimwu0+hsXnRNHZUGKVksQ/9t7AD7/7L8aPj9jPqu1EjTS1/6IDB0
QDVyW7Z6hX7YoUx48gp+j/UFJ7ZyxTajy+0wvzPHou3KJARgFfNZWT2XvvYcpA0/
yqcpbCUwZ1AETXHcmly7YwNpPV9LBg==
=+Xw/
-----END PGP SIGNATURE-----
Merge tag 'spi-v6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"This release sees some exciting changes from David Lechner which
implements some optimisations that have been talked about for a long
time which allows client drivers to pre-prepare SPI messages for
repeated or low latency use. This lets us move work out of latency
sensitive paths and avoid repeating work for frequently performed
operations. As well as being useful in itself this will also be used
in future to allow controllers to directly trigger SPI operations (eg,
from interrupts).
Otherwise this release has mostly been focused on cleanups, plus a
couple of new devices:
- Support for pre-optimising messages
- A big set of updates from Uwe Kleine-König moving drivers to use
APIs with more modern terminology for controllers
- Major overhaul of the s3c64xx driver
- Support for Google GS101 and Samsung Exynos850"
* tag 'spi-v6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (122 commits)
spi: Introduce SPI_INVALID_CS and is_valid_cs()
spi: Fix types of the last chip select storage variables
spi: Consistently use BIT for cs_index_mask
spi: Exctract spi_dev_check_cs() helper
spi: Exctract spi_set_all_cs_unused() helper
spi: s3c64xx: switch exynos850 to new port config data
spi: s3c64xx: switch gs101 to new port config data
spi: s3c64xx: deprecate fifo_lvl_mask, rx_lvl_offset and port_id
spi: s3c64xx: get rid of the OF alias ID dependency
spi: s3c64xx: introduce s3c64xx_spi_set_port_id()
spi: s3c64xx: let the SPI core determine the bus number
spi: s3c64xx: allow FIFO depth to be determined from the compatible
spi: s3c64xx: retrieve the FIFO depth from the device tree
spi: s3c64xx: determine the fifo depth only once
spi: s3c64xx: allow full FIFO masks
spi: s3c64xx: define a magic value
spi: dt-bindings: introduce FIFO depth properties
spi: axi-spi-engine: use struct_size() macro
spi: axi-spi-engine: use __counted_by() attribute
spi: axi-spi-engine: remove p from struct spi_engine_message_state
...
Yes, yes, I know the slab people were planning on going slow and letting
every subsystem fight this thing on their own. But let's just rip off
the band-aid and get it over and done with. I don't want to see a
number of unnecessary pull requests just to get rid of a flag that no
longer has any meaning.
This was mainly done with a couple of 'sed' scripts and then some manual
cleanup of the end result.
Link: https://lore.kernel.org/all/CAHk-=wji0u+OOtmAOD-5JV3SXcRJF___k_+8XNKmak0yd5vW1Q@mail.gmail.com/
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This pull request contains two patches that convert tasklet users to BH
workqueue - backtractest and usb hcd. DM conversions are being routed
through the respective subsystem tree. Hopefully, the next cycle will see a
lot more conversions.
-----BEGIN PGP SIGNATURE-----
iIQEABYKACwWIQTfIjM1kS57o3GsC/uxYfJx3gVYGQUCZe7KuA4cdGpAa2VybmVs
Lm9yZwAKCRCxYfJx3gVYGUmfAQC6bbrghugnvvAREeJSymM6aATfICTrN98FdBIC
cRn5KgEAqDpKcFA2zbWXPPU7KGBjAAYX199XFc9+NqiXpvCfoA8=
=uQz1
-----END PGP SIGNATURE-----
Merge tag 'wq-for-6.9-bh-conversions' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
Pull workqueue BH conversions from Tejun Heo:
"This contains two patches that convert tasklet users to BH workqueues:
backtracetest and usb hcd.
DM conversions are being routed through the respective subsystem tree.
Hopefully, the next cycle will see a lot more conversions"
* tag 'wq-for-6.9-bh-conversions' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
usb: core: hcd: Convert from tasklet to BH workqueue
backtracetest: Convert from tasklet to BH workqueue
Here are the USB-serial updates for 6.9-rc1, including:
- new device ids
- removal of some redundant assignments
All have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCZerHTQAKCRALxc3C7H1l
CPboAQDNco4mivrvMutpWwwA128eE6ENdFTLByAyywzr/i9nzwEAncNyygGXxKt+
7BQUx6BR8vm1qcauPVdDRKwYf6UMkgM=
=uQTq
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-6.9-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for 6.9-rc1
Here are the USB-serial updates for 6.9-rc1, including:
- new device ids
- removal of some redundant assignments
All have been in linux-next with no reported issues.
* tag 'usb-serial-6.9-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: cp210x: add pid/vid for TDK NC0110013M and MM0110113M
USB: serial: keyspan: remove redundant assignment to pointer data
USB: serial: ftdi_sio: remove redundant assignment to variable cflag
USB: serial: oti6858: remove redundant assignment to variable divisor
USB: serial: option: add MeiG Smart SLM320 product
USB: serial: cp210x: add ID for MGP Instruments PDS100
USB: serial: add device ID for VeriFone adapter
USB: serial: ftdi_sio: add support for GMC Z216C Adapter IR-USB
Currently the variable irqflags is being set but is not being used,
it appears it should be used in the call to net2272_probe_fin
rather than IRQF_TRIGGER_LOW being used. Kudos to Uwe Kleine-König
for suggesting the fix.
Cleans up clang scan build warning:
drivers/usb/gadget/udc/net2272.c:2610:15: warning: variable 'irqflags'
set but not used [-Wunused-but-set-variable]
Fixes: ceb80363b2 ("USB: net2272: driver for PLX NET2272 USB device controller")
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20240307181734.2034407-1-colin.i.king@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit resolves an issue in the tegra-xudc USB gadget driver that
incorrectly fetched USB3 PHY instances. The problem stemmed from the
assumption of a one-to-one correspondence between USB2 and USB3 PHY
names and their association with physical USB ports in the device tree.
Previously, the driver associated USB3 PHY names directly with the USB3
instance number, leading to mismatches when mapping the physical USB
ports. For instance, if using USB3-1 PHY, the driver expect the
corresponding PHY name as 'usb3-1'. However, the physical USB ports in
the device tree were designated as USB2-0 and USB3-0 as we only have
one device controller, causing a misalignment.
This commit rectifies the issue by adjusting the PHY naming logic.
Now, the driver correctly correlates the USB2 and USB3 PHY instances,
allowing the USB2-0 and USB3-1 PHYs to form a physical USB port pair
while accurately reflecting their configuration in the device tree by
naming them USB2-0 and USB3-0, respectively.
The change ensures that the PHY and PHY names align appropriately,
resolving the mismatch between physical USB ports and their associated
names in the device tree.
Fixes: b4e19931c9 ("usb: gadget: tegra-xudc: Support multiple device modes")
Cc: stable@vger.kernel.org
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20240307030328.1487748-3-waynec@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Function checkdone is only required if QUIRK2 is defined, so add
appropriate #if / #endif around the function.
Cleans up clang scan build warning:
drivers/usb/host/sl811-hcd.c:588:18: warning: unused function
'checkdone' [-Wunused-function]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20240307111351.1982382-1-colin.i.king@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit "usb: Export BOS descriptor to sysfs" added a binary attribute
group to sysfs. It doesn't check if the descriptors attribute should be
visible, which is by design and not an oversight. Update a comment so that
it better explains this in the dev_bin_attrs_are_visible() function.
Signed-off-by: Elbert Mai <code@elbertmai.com>
Link: https://lore.kernel.org/r/20240306001503.313028-1-code@elbertmai.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SLAB_MEM_SPREAD flag used to be implemented in SLAB, which was
removed as of v6.8-rc1, so it became a dead flag since the commit
16a1d96835 ("mm/slab: remove mm/slab.c and slab_def.h"). And the
series[1] went on to mark it obsolete explicitly to avoid confusion
for users. Here we can just remove all its users, which has no any
functional change.
[1] https://lore.kernel.org/all/20240223-slab-cleanup-flags-v2-1-02f1753e8303@suse.cz/
Signed-off-by: Chengming Zhou <zhouchengming@bytedance.com>
Acked-by: Rui Miguel Silva <rui.silva@linaro.org>
Link: https://lore.kernel.org/r/20240305132442.2122214-1-chengming.zhou@linux.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ring expansion checker may incorrectly assume a completely full ring
is empty, missing the need for expansion.
This is due to a special empty ring case where the dequeue ends up
ahead of the enqueue pointer. This is seen when enqueued TRBs fill up
exactly a segment, with enqueue then pointing to the end link TRB.
Once those TRBs are handled the dequeue pointer will follow the link
TRB and end up pointing to the first entry on the next segment, past
the enqueue.
This same enqueue - dequeue condition can be true if a ring is full,
with enqueue ending on that last link TRB before the dequeue pointer
on the next segment.
This can be seen when queuing several ~510 small URBs via usbfs in
one go before a single one is handled (i.e. dequeue not moved from first
entry in segment).
Expand the ring already when enqueue reaches the link TRB before the
dequeue segment, instead of expanding it when enqueue moves into the
dequeue segment.
Reported-by: Chris Yokum <linux-usb@mail.totalphase.com>
Closes: https://lore.kernel.org/all/949223224.833962.1709339266739.JavaMail.zimbra@totalphase.com
Tested-by: Chris Yokum <linux-usb@mail.totalphase.com>
Fixes: f5af638f06 ("xhci: Fix transfer ring expansion size calculation")
Cc: stable@vger.kernel.org # v6.5+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240305132312.955171-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 14485de431 ("usb: Use device_get_match_data()") overlooked the
already existing pointer to pdev->dev 'dev'.
Use the existing pointer 'dev' in device_get_match_data() to keep code
consistency.
Acked-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Javier Carrasco <javier.carrasco@wolfvision.net>
Link: https://lore.kernel.org/r/20240305-onboard_xvf3500-v7-1-ad3fb50e593b@wolfvision.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver already support the tcpci binding for the i2c_device_id so
add the support for the of_device_id too.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240222210903.208901-3-m.felsch@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The custom log wrappers ERR, WARNING, DBG and VDBG don't add anything
useful that cannot easily be done with dev_err() and friends. Replace
the custom stuff by the well known functions from printk.h.
Also drop some dead code in a #if 0 block.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20240304165404.807787-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a USB hub is described in DT, such as any device that matches the
onboard-hub driver, the connect_type is set to "unknown" or
USB_PORT_CONNECT_TYPE_UNKNOWN. This makes any device plugged into that
USB port report their 'removable' device attribute as "unknown".
ChromeOS userspace would like to know if the USB device is actually
removable or not so that security policies can be applied. Improve the
connect_type attribute for ports, and in turn the removable attribute
for USB devices, by looking for child devices with a reg property or an
OF graph when the device is described in DT.
If the graph exists, endpoints that are connected to a remote node must
be something like a usb-{a,b,c}-connector compatible node, or an
intermediate node like a redriver, and not a hardwired USB device on the
board. Set the connect_type to USB_PORT_CONNECT_TYPE_HOT_PLUG in this
case because the device is going to be plugged in. Set the connect_type
to USB_PORT_CONNECT_TYPE_HARD_WIRED if there's a child node for the port
like 'device@2' for port2. Set the connect_type to USB_PORT_NOT_USED if
there isn't an endpoint or child node corresponding to the port number.
To make sure things don't change, only set the port to not used if
there are child nodes. This way an onboard hub connect_type doesn't
change until ports are added or child nodes are added to describe
hardwired devices. It's assumed that all ports or no ports will be
described for a device.
Cc: Matthias Kaehlcke <mka@chromium.org>
Cc: linux-usb@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: Pin-yen Lin <treapking@chromium.org>
Cc: maciek swiech <drmasquatch@google.com>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20240223005823.3074029-3-swboyd@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TI TUSB8020B is a 2-port USB 3.0 hub. Add support for
this hub in the driver in order to bring up reset, and supply
dependencies.
Power-up: Issue a GPIO reset (GRSTz) 3ms after VDD and VDD33 stabilize.
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240227090228.22156-2-macpaul.lin@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The variable count is being initialized and incremented but it is never
actually referenced in any other way. The variable is redundant and can
be removed.
Cleans up clang scan build warning:
drivers/usb/musb/musb_gadget.c:1747:12: warning: variable 'count' set
but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20240229115548.218713-1-colin.i.king@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All AM62 devices have Errata i2409 [1] due to which
USB2 PHY may lock up due to short suspend.
Workaround involves setting bit 5 and 4 PLL_REG12
in PHY2 register space after USB controller is brought
out of LPSC reset but before controller initialization.
Handle this workaround.
[1] - https://www.ti.com/lit/er/sprz487d/sprz487d.pdf
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240227-for-v6-9-am62-usb-errata-3-0-v4-4-0ada8ddb0767@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TRM information is outdated and design team has confirmed
that PHY_CORE_VOLTAGE should be 0 irrespective of
VDD_CORE voltage.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240227-for-v6-9-am62-usb-errata-3-0-v4-3-0ada8ddb0767@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Disable wakeup at remove.
Fixes the below warnings on module unload and reload.
> dwc3-am62 f900000.dwc3-usb: couldn't enable device as a wakeup source: -17
> dwc3-am62 f910000.dwc3-usb: couldn't enable device as a wakeup source: -17
Fixes: 4e3972b589 ("usb: dwc3-am62: Enable as a wakeup source by default")
Cc: stable@vger.kernel.org # v6.4+
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240227-for-v6-9-am62-usb-errata-3-0-v4-2-0ada8ddb0767@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As runtime PM is enabled, the module can be runtime
suspended when .remove() is called.
Do a pm_runtime_get_sync() to make sure module is active
before doing any register operations.
Doing a pm_runtime_put_sync() should disable the refclk
so no need to disable it again.
Fixes the below warning at module removel.
[ 39.705310] ------------[ cut here ]------------
[ 39.710004] clk:162:3 already disabled
[ 39.713941] WARNING: CPU: 0 PID: 921 at drivers/clk/clk.c:1090 clk_core_disable+0xb0/0xb8
We called of_platform_populate() in .probe() so call the
cleanup function of_platform_depopulate() in .remove().
Get rid of the now unnnecessary dwc3_ti_remove_core().
Without this, module re-load doesn't work properly.
Fixes: e8784c0aec ("drivers: usb: dwc3: Add AM62 USB wrapper driver")
Cc: stable@vger.kernel.org # v5.19+
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240227-for-v6-9-am62-usb-errata-3-0-v4-1-0ada8ddb0767@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hi3798MV200 uses dwc3 controller with a few more clocks and a dedicated
resets. Use of_simple driver for it.
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
Link: https://lore.kernel.org/r/20240225-dwc3-v4-2-8c1fd6c6f615@outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While connecting to a Linux host with CDC_NCM_NTB_DEF_SIZE_TX
set to 65536, it has been observed that we receive short packets,
which come at interval of 5-10 seconds sometimes and have block
length zero but still contain 1-2 valid datagrams present.
According to the NCM spec:
"If wBlockLength = 0x0000, the block is terminated by a
short packet. In this case, the USB transfer must still
be shorter than dwNtbInMaxSize or dwNtbOutMaxSize. If
exactly dwNtbInMaxSize or dwNtbOutMaxSize bytes are sent,
and the size is a multiple of wMaxPacketSize for the
given pipe, then no ZLP shall be sent.
wBlockLength= 0x0000 must be used with extreme care, because
of the possibility that the host and device may get out of
sync, and because of test issues.
wBlockLength = 0x0000 allows the sender to reduce latency by
starting to send a very large NTB, and then shortening it when
the sender discovers that there’s not sufficient data to justify
sending a large NTB"
However, there is a potential issue with the current implementation,
as it checks for the occurrence of multiple NTBs in a single
giveback by verifying if the leftover bytes to be processed is zero
or not. If the block length reads zero, we would process the same
NTB infintely because the leftover bytes is never zero and it leads
to a crash. Fix this by bailing out if block length reads zero.
Cc: stable@vger.kernel.org
Fixes: 427694cfaa ("usb: gadget: ncm: Handle decoding of multiple NTB's in unwrap call")
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Maciej Żenczykowski <maze@google.com>
Link: https://lore.kernel.org/r/20240228115441.2105585-1-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DisplayPort driver's sysfs nodes may be present to the userspace before
typec_altmode_set_drvdata() completes in dp_altmode_probe. This means that
a sysfs read can trigger a NULL pointer error by deferencing dp->hpd in
hpd_show or dp->lock in pin_assignment_show, as dev_get_drvdata() returns
NULL in those cases.
Remove manual sysfs node creation in favor of adding attribute group as
default for devices bound to the driver. The ATTRIBUTE_GROUPS() macro is
not used here otherwise the path to the sysfs nodes is no longer compliant
with the ABI.
Fixes: 0e3bb7d689 ("usb: typec: Add driver for DisplayPort alternate mode")
Cc: stable@vger.kernel.org
Signed-off-by: RD Babiera <rdbabiera@google.com>
Link: https://lore.kernel.org/r/20240229001101.3889432-2-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Register SOP' alternate modes with a Type-C Connector Class cable plug.
Alternate modes are queried from the PPM using the GET_ALTERNATE_MODES
command with recipient set to SOP'.
Reviewed-by: Benson Leung <bleung@chromium.org>
Reviewed-by: Prashant Malani <pmalani@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Jameson Thies <jthies@google.com>
Link: https://lore.kernel.org/r/20240305025804.1290919-5-jthies@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Register SOP and SOP' Discover Identity responses with the USB Type-C
Connector Class as partner and cable identities, respectively. Discover
Identity responses are requested from the PPM using the GET_PD_MESSAGE
UCSI command.
Signed-off-by: Jameson Thies <jthies@google.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Link: https://lore.kernel.org/r/20240305025804.1290919-4-jthies@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Register cables with the Type-C Connector Class in the UCSI driver based
on the PPM response to GET_CABLE_PROPERTY. Registered cable properties
include plug type, cable type and major revision.
Reviewed-by: Benson Leung <bleung@chromium.org>
Reviewed-by: Prashant Malani <pmalani@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Jameson Thies <jthies@google.com>
Link: https://lore.kernel.org/r/20240305025804.1290919-3-jthies@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While commit 69f89168b3 ("usb: typec: tpcm: Fix issues with power being
removed during reset") fixes the boot issues for bus powered devices such
as LibreTech Renegade Elite/Firefly, it trades off the CC pins NOT being
Hi-Zed during errory recovery (i.e PORT_RESET) for devices which are NOT
bus powered(a.k.a self powered). This change Hi-Zs the CC pins only for
self powered devices, thus preventing brown out for bus powered devices
Adhering to spec is gaining more importance due to the Common charger
initiative enforced by the European Union.
Quoting from the spec:
4.5.2.2.2.1 ErrorRecovery State Requirements
The port shall not drive VBUS or VCONN, and shall present a
high-impedance to ground (above zOPEN) on its CC1 and CC2 pins.
Hi-Zing the CC pins is the inteded behavior for PORT_RESET.
CC pins are set to default state after tErrorRecovery in
PORT_RESET_WAIT_OFF.
4.5.2.2.2.2 Exiting From ErrorRecovery State
A Sink shall transition to Unattached.SNK after tErrorRecovery.
A Source shall transition to Unattached.SRC after tErrorRecovery.
Fixes: 69f89168b3 ("usb: typec: tpcm: Fix issues with power being removed during reset")
Cc: stable@vger.kernel.org
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Tested-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20240228000512.746252-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On SM8550 and SM8650 Qualcomm platforms a call to UCSI_GET_PDOS for
non-PD partners will cause a firmware crash with no
easy way to recover from it.
Add UCSI_NO_PARTNER_PDOS quirk for those platform until we find
a way to properly handle the crash.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240223-topic-sm8550-upstream-ucsi-no-pdos-v1-1-8900ad510944@linaro.org
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the port is setting the pin configuration when no configuration is
chosen, the DisplayPort driver will not send Configure to the cable plug
if it's available. Add transition to DP_STATE_CONFIGURE_PRIME.
Fixes: 71ba4fe566 ("usb: typec: altmodes/displayport: add SOP' support")
Signed-off-by: RD Babiera <rdbabiera@google.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240223002302.3937235-2-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Smatch checker flags svdm_version being uninitialized for Discover
Identity Messages within tcpm_pd_svdm for the CMDT_INIT case. Cable plugs
cannot initialize SVDM commands, however a port partner that isn't allowed
to communicate over SOP' could, which would result in the CMDT_INIT block
running for a received SOP' message.
First, initialize svdm_version for the TCPC_TX_SOP_PRIME case. If the
svdm_version returns as an error, we expect the received svdm to be the
result of Discover Identity that updates the value accordingly.
Next, drop all SOP' messages of type CMDT_INIT within tcpm_pd_svdm.
Finally, remove redundant call that assigns modep and pdev. Smatch will
raise an uninitialized symbol error over modep_prime and pdev_prime, but
both the assignment and use of these variables are guarded behind
a check for rx_sop_type == TCPC_TX_SOP_PRIME.
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/all/a432603b-b801-4001-b309-247dded707d3@moroto.mountain/
Fixes: fb7ff25ae4 ("usb: typec: tcpm: add discover identity support for SOP'")
Signed-off-by: RD Babiera <rdbabiera@google.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240223002233.3936275-2-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ports with _UPC (USB Port Capability) ACPI objects stating they are
"not connectable" are not wired to any connector or internal device.
They only exist inside the host controller.
These ports may not have an ACPI _PLD (Physical Location of Device)
object.
Rework the code so that _UPC is read even if _PLD does not exist, and
make sure the port->connect_type is set to "USB_PORT_NOT_USED" instead
of "USB_PORT_CONNECT_TYPE_UNKNOWN".
No bugs or known issues are reported due to possibly not parsing _UPC,
and thus leaving the port connect type as "unknown" instead of
"not used". Nice to have this fixed but no need to add it to stable
kernels, or urgency to get it upstream.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240223140305.185182-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Minimal ACPI support was added to the Qualcomm DWC3 glue driver in order to
enable USB on SDM850 and SC8180X compute platforms. The support is still
functional, but unnoticed regressions in other drivers indicates that no
one actually booting any of platforms dependent on this implementation.
The functionality provides is the bare minimum and is not expected to aid
in the effort of bringing full ACPI support to the driver in the future.
Remove the ACPI code from the Qualcomm DWC3 glue driver to aid in the
implementation of improvements that are actually used like multiport and
flattening device tree.
Commit message by Bjorn Andersson.
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240305093216.3814787-1-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Motivation
----------
The binary device object store (BOS) of a USB device consists of the BOS
descriptor followed by a set of device capability descriptors. One that is
of interest to users is the platform descriptor. This contains a 128-bit
UUID and arbitrary data, and it allows parties outside of USB-IF to add
additional metadata about a USB device in a standards-compliant manner.
Notable examples include the WebUSB and Microsoft OS 2.0 descriptors.
The kernel already retrieves and caches the BOS from USB devices if its
bcdUSB is >= 0x0201. Because the BOS is flexible and extensible, we export
the entire BOS to sysfs so users can retrieve whatever device capabilities
they desire, without requiring USB I/O or elevated permissions.
Implementation
--------------
Add bos_descriptors attribute to sysfs. This is a binary file and it works
the same way as the existing descriptors attribute. The file exists only if
the BOS is present in the USB device.
Also create a binary attribute group, so the driver core can handle the
creation of both the descriptors and bos_descriptors attributes in sysfs.
Signed-off-by: Elbert Mai <code@elbertmai.com>
Link: https://lore.kernel.org/r/20240305002301.95323-1-code@elbertmai.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TDK NC0110013M and MM0110113M have custom USB IDs for CP210x,
so we need to add them to the driver.
Signed-off-by: Toru Katagiri <Toru.Katagiri@tdk.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
The pointer data is being assigned a value that is not being
read afterwards, it is being re-assigned later inside a do-while
loop. The assignment is redundant and can be removed.
Cleans up clang scan warning:
drivers/usb/serial/keyspan.c:924:2: warning: Value stored to 'data'
is never read [deadcode.DeadStores]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
The variable cflag is being assigned a value that is not being read
afterwards, it is being re-assigned later on. The assignment is
redundant and can be removed.
Cleans up clang scan warning:
drivers/usb/serial/ftdi_sio.c:2613:15: warning: Value stored to 'cflag'
during its initialization is never read [deadcode.DeadStores]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
The variable divisor is being assigned a value that is not being
read afterward, it is being re-assigned later in both paths of an if
statement. The assignment is redundant and can be removed.
Cleans up clang scan warning:
drivers/usb/serial/oti6858.c:412:2: warning: Value stored to 'divisor'
is never read [deadcode.DeadStores]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
The radiation meter has the text MGP Instruments PDS-100G or PDS-100GN
produced by Mirion Technologies. Tested by forcing the driver
association with
echo 10c4 863c > /sys/bus/usb-serial/drivers/cp210x/new_id
and then setting the serial port in 115200 8N1 mode. The device
announces ID_USB_VENDOR_ENC=Silicon\x20Labs and ID_USB_MODEL_ENC=PDS100
Signed-off-by: Christian Häggström <christian.haggstrom@orexplore.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
The GMC IR-USB adapter cable utilizes a FTDI FT232R chip.
Add VID/PID for this adapter so it can be used as serial device via
ftdi_sio.
Signed-off-by: Daniel Vogelbacher <daniel@chaospixel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
A call to usb_set_interface() crashes if the device is deallocated
concurrently, such as due to physical removal or a serious IO error.
It could also interfere with other drivers using the device if the
current driver is unbound before the call is finished.
Document the need to delay driver unbinding until this call returns,
which solves both issues.
Document the same regarding usb_clear_halt(), which is equally known
to be routinely called by drivers.
Explicitly mention finishing pending operations in the documentation
of the driver disconnect callback.
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Link: https://lore.kernel.org/r/20240218092515.7635ff8c@foxbook
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The isd200 sub-driver in usb-storage uses the HEADS and SECTORS values
in the ATA ID information to calculate cylinder and head values when
creating a CDB for READ or WRITE commands. The calculation involves
division and modulus operations, which will cause a crash if either of
these values is 0. While this never happens with a genuine device, it
could happen with a flawed or subversive emulation, as reported by the
syzbot fuzzer.
Protect against this possibility by refusing to bind to the device if
either the ATA_ID_HEADS or ATA_ID_SECTORS value in the device's ID
information is 0. This requires isd200_Initialization() to return a
negative error code when initialization fails; currently it always
returns 0 (even when there is an error).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+28748250ab47a8f04100@syzkaller.appspotmail.com
Link: https://lore.kernel.org/linux-usb/0000000000003eb868061245ba7f@google.com/
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Reviewed-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/b1e605ea-333f-4ac0-9511-da04f411763e@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently xhci_map_urb_for_dma() creates a temporary buffer and copies
the SG list to the new linear buffer. But if the kzalloc_node() fails,
then the following sg_pcopy_to_buffer() can lead to crash since it
tries to memcpy to NULL pointer.
So return -ENOMEM if kzalloc returns null pointer.
Cc: stable@vger.kernel.org # 5.11
Fixes: 2017a1e584 ("usb: xhci: Use temporary buffer to consolidate SG")
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240229141438.619372-10-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DbC driver starts polling for events immediately when DbC is enabled.
The current polling interval is 1ms, which keeps the CPU busy, impacting
power management even when there are no active data transfers.
Solve this by polling at a slower rate, with a 64ms interval as default
until a transfer request is queued, or if there are still are pending
unhandled transfers at event completion.
Tested-by: Uday M Bhat <uday.m.bhat@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240229141438.619372-9-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Two NEC uPD720200 adapters have been observed to randomly misbehave:
a Stop Endpoint command fails with Context Error, the Output Context
indicates Stopped state, and the endpoint keeps running. Very often,
Set TR Dequeue Pointer is seen to fail next with Context Error too,
in addition to problems from unexpectedly completed cancelled work.
The pathology is common on fast running isoc endpoints like uvcvideo,
but has also been reproduced on a full-speed bulk endpoint of pl2303.
It seems all EPs are affected, with risk proportional to their load.
Reproduction involves receiving any kind of stream and closing it to
make the device driver cancel URBs already queued in advance.
Deal with it by retrying the command like in the Running state.
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240229141438.619372-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A trb_in_td() call is used to determine if a completion event matches
any TRB of the currently executing TD. This function is told to start
searching right after the last finished TD, which is not at all where
the currently expected TD is guaranteed to begin, because some TDs in
between may have been cancelled.
Not only is a pointless work performed, but a bug resulting in the HC
executing cancelled TDs was seen to trick the driver into associating
events from a TD just cancelled with an unrelated future TD.
Since the ring is being traversed for the specific purpose of finding
a match with the current TD, always start from its first TRB. This is
the most reliable bit of information that we posses.
Tracking of HC's work progress is not affected, except for cases when
a misattributed event would have moved dequeue past a pending TD.
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240229141438.619372-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor the code to improve readability by using
'xhci_free_segments_for_ring()' function for freeing ring segments.
This replaces the custom while loop previously used within
'xhci_ring_expansion()' and 'xhci_alloc_segments_for_ring()'.
Slightly modify 'xhci_free_segments_for_ring()' to handle lists
which do not loop. This makes it possible to use it in error
paths of 'xhci_alloc_segments_for_ring()'.
This change also prepares for switching the custom xhci linked segment
list into to more standard list.h lists.
[minor commit message rewording -Mathias]
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240229141438.619372-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace a segment of code within 'xhci_clear_command_ring()' with a
function call to 'xhci_initialize_ring_info()'. This change eliminates
code duplication, as 'xhci_initialize_ring_info()' performs the same
operations as the replaced code.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240229141438.619372-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Slot ID is a index of a virtual device in struct 'xhci_hcd->devs[]'.
Previously, to get the slot ID associated with a port, we had to loop
through all devices and compare ports, which is very inefficient.
Instead, the slot ID (of the device which is directly connected to the
port), is added to the its corresponding 'xhci_port' struct. As a result,
finding the port's device is quick and easy.
Function 'xhci_find_slot_id_by_port()' is removed, as it is no longer
needed.
Signed-off-by: Niklas Neronin <niklas.neronin@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240229141438.619372-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variables real & fake port do not convey their purpose, thus they are
replaced with a pointer to the root hub port 'struct xhci_port *rhub_port'.
'rhub_port' contains real & fake ports in zero-based format, which happens
to be more widely used inside the xHCI driver:
- 'real_port' is ('rhub_port->hw_portnum' + 1)
- 'fake_port' is ('rhub_port->hcd_portnum' + 1)
One reason for real port being one-based, is to signal other functions in
case struct 'xhci_virt_device' initialization failed, in this case the
value will remain 0. This is no longer needed, instead we check whether
or not 'rhub_port' is 'NULL'.
Signed-off-by: Niklas Neronin <niklas.neronin@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240229141438.619372-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xHC hardware needs to know which roothub port a USB device is attached to
when controlling the device, so the xHCI driver stores in each device the
roothub port which it's connected behind. This is done with two different
port index values, the 'real_port' which is an index to the xHC hardware
port register array, and the 'fake_port' which is the per hub port index
used by the hub driver.
Instead of finding real & fake port separately, find the root hub port
'xhci_port' structure which contains both real & fake port values:
- 'real_port' is ('hw_portnum' + 1)
- 'fake_port' is ('hcd_portnum' + 1)
i.e. real & fake port are 'hw_portnum' & 'hcd_portnum' in one-based
format.
The 'xhci_port' structure is a better way to refer to roothub ports than
the 'real_port' & 'fake_port'. As a result, these port indexes are slated
to be replaced with a direct pointer to the root hub port. This patch
setups the ground work for the future changes.
Signed-off-by: Niklas Neronin <niklas.neronin@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240229141438.619372-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 43a7206b09 ("driver core: class: make class_register() take
a const *"), the driver core allows for struct class to be in read-only
memory, so move the structures typec_mux_class, retimer_class and
typec_class to be declared at build time placing them into read-only
memory, instead of having to be dynamically allocated at boot time.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Link: https://lore.kernel.org/r/20240301-class_cleanup-usb-v1-1-50309e325095@marliere.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need it here for the USB fixes, and it resolves a merge conflict as
reported in linux-next in drivers/usb/roles/class.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some small USB fixes for 6.8-rc6 to resolve some reported
problems. These include:
- regression fixes with typec tpcm code as reported by many
- cdnsp and cdns3 driver fixes
- usb role setting code bugfixes
- build fix for uhci driver
- ncm gadget driver bugfix
- MAINTAINERS entry update
All of these have been in linux-next all week with no reported issues
and there is at least one fix in here that is in Thorsten's regression
list that is being tracked.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZdtGEA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymzsgCg2IsWqIR72XUGsa5rrbRnskOP/G4An24BmUb6
t34d0VjiHagZTFlfRx6g
=eOL1
-----END PGP SIGNATURE-----
Merge tag 'usb-6.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB fixes for 6.8-rc6 to resolve some reported
problems. These include:
- regression fixes with typec tpcm code as reported by many
- cdnsp and cdns3 driver fixes
- usb role setting code bugfixes
- build fix for uhci driver
- ncm gadget driver bugfix
- MAINTAINERS entry update
All of these have been in linux-next all week with no reported issues
and there is at least one fix in here that is in Thorsten's regression
list that is being tracked"
* tag 'usb-6.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: typec: tpcm: Fix issues with power being removed during reset
MAINTAINERS: Drop myself as maintainer of TYPEC port controller drivers
usb: gadget: ncm: Avoid dropping datagrams of properly parsed NTBs
Revert "usb: typec: tcpm: reset counter when enter into unattached state after try role"
usb: gadget: omap_udc: fix USB gadget regression on Palm TE
usb: dwc3: gadget: Don't disconnect if not started
usb: cdns3: fix memory double free when handle zero packet
usb: cdns3: fixed memory use after free at cdns3_gadget_ep_disable()
usb: roles: don't get/set_role() when usb_role_switch is unregistered
usb: roles: fix NULL pointer issue when put module's reference
usb: cdnsp: fixed issue with incorrect detecting CDNSP family controllers
usb: cdnsp: blocked some cdns3 specific code
usb: uhci-grlib: Explicitly include linux/platform_device.h
Six fixes: the four driver ones are pretty trivial. The larger two
core changes are to try to fix various USB attached devices which have
somewhat eccentric ways of handling the VPD and other mode pages which
necessitate multiple revalidates (that were removed in the interests
of efficiency) and updating the heuristic for supported VPD pages.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCZdkyyyYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishS2KAP0V8RVm
U1gUoE4doIV9WdK8Dv0MUxnOpYVvjhRjM8PA1QEAwaPJivC91smxJv4MOIDq0PL3
9qyMwQq4jWH/2zS14p8=
=8aq+
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Six fixes: the four driver ones are pretty trivial.
The larger two core changes are to try to fix various USB attached
devices which have somewhat eccentric ways of handling the VPD and
other mode pages which necessitate multiple revalidates (that were
removed in the interests of efficiency) and updating the heuristic for
supported VPD pages"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: jazz_esp: Only build if SCSI core is builtin
scsi: smartpqi: Fix disable_managed_interrupts
scsi: ufs: Uninitialized variable in ufshcd_devfreq_target()
scsi: target: pscsi: Fix bio_put() for error case
scsi: core: Consult supported VPD page list prior to fetching page
scsi: sd: usb_storage: uas: Access media prior to querying device properties
Since the merge of b717dfbf73 ("Revert "usb: typec: tcpm: fix
cc role at port reset"") into mainline the LibreTech Renegade
Elite/Firefly has died during boot, the main symptom observed in testing
is a sudden stop in console output. Gábor Stefanik identified in review
that the patch would cause power to be removed from devices without
batteries (like this board), observing that while the patch is correct
according to the spec this appears to be an oversight in the spec.
Given that the change makes previously working systems unusable let's
revert it, there was some discussion of identifying systems that have
alternative power and implementing the standards conforming behaviour in
only that case.
Fixes: b717dfbf73 ("Revert "usb: typec: tcpm: fix cc role at port reset"")
Cc: stable <stable@kernel.org>
Cc: Badhri Jagan Sridharan <badhri@google.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20240212-usb-fix-renegade-v1-1-22c43c88d635@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit aed65af1cc ("drivers: make device_type const"), the driver
core can properly handle constant struct device_type. Move the
usb_device_type, usb_if_device_type, usb_ep_device_type and
usb_port_device_type variables to be constant structures as well, placing
it into read-only memory which can not be modified at runtime.
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Link: https://lore.kernel.org/r/20240218-device_cleanup-usb-v1-4-77423c4da262@marliere.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit aed65af1cc ("drivers: make device_type const"), the driver
core can properly handle constant struct device_type. Move the gadget_type
variable to be a constant structure as well, placing it into read-only
memory which can not be modified at runtime.
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Link: https://lore.kernel.org/r/20240218-device_cleanup-usb-v1-3-77423c4da262@marliere.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit aed65af1cc ("drivers: make device_type const"), the driver
core can properly handle constant struct device_type. Move the
usb_phy_dev_type variable to be a constant structure as well, placing it
into read-only memory which can not be modified at runtime.
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Link: https://lore.kernel.org/r/20240218-device_cleanup-usb-v1-2-77423c4da262@marliere.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit aed65af1cc ("drivers: make device_type const"), the driver
core can properly handle constant struct device_type. Move all the
device_type variables in use by the driver to be constant structures as
well, placing it into read-only memory which can not be modified at
runtime.
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Link: https://lore.kernel.org/r/20240218-device_cleanup-usb-v1-1-77423c4da262@marliere.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is observed sometimes when tethering is used over NCM with Windows 11
as host, at some instances, the gadget_giveback has one byte appended at
the end of a proper NTB. When the NTB is parsed, unwrap call looks for
any leftover bytes in SKB provided by u_ether and if there are any pending
bytes, it treats them as a separate NTB and parses it. But in case the
second NTB (as per unwrap call) is faulty/corrupt, all the datagrams that
were parsed properly in the first NTB and saved in rx_list are dropped.
Adding a few custom traces showed the following:
[002] d..1 7828.532866: dwc3_gadget_giveback: ep1out:
req 000000003868811a length 1025/16384 zsI ==> 0
[002] d..1 7828.532867: ncm_unwrap_ntb: K: ncm_unwrap_ntb toprocess: 1025
[002] d..1 7828.532867: ncm_unwrap_ntb: K: ncm_unwrap_ntb nth: 1751999342
[002] d..1 7828.532868: ncm_unwrap_ntb: K: ncm_unwrap_ntb seq: 0xce67
[002] d..1 7828.532868: ncm_unwrap_ntb: K: ncm_unwrap_ntb blk_len: 0x400
[002] d..1 7828.532868: ncm_unwrap_ntb: K: ncm_unwrap_ntb ndp_len: 0x10
[002] d..1 7828.532869: ncm_unwrap_ntb: K: Parsed NTB with 1 frames
In this case, the giveback is of 1025 bytes and block length is 1024.
The rest 1 byte (which is 0x00) won't be parsed resulting in drop of
all datagrams in rx_list.
Same is case with packets of size 2048:
[002] d..1 7828.557948: dwc3_gadget_giveback: ep1out:
req 0000000011dfd96e length 2049/16384 zsI ==> 0
[002] d..1 7828.557949: ncm_unwrap_ntb: K: ncm_unwrap_ntb nth: 1751999342
[002] d..1 7828.557950: ncm_unwrap_ntb: K: ncm_unwrap_ntb blk_len: 0x800
Lecroy shows one byte coming in extra confirming that the byte is coming
in from PC:
Transfer 2959 - Bytes Transferred(1025) Timestamp((18.524 843 590)
- Transaction 8391 - Data(1025 bytes) Timestamp(18.524 843 590)
--- Packet 4063861
Data(1024 bytes)
Duration(2.117us) Idle(14.700ns) Timestamp(18.524 843 590)
--- Packet 4063863
Data(1 byte)
Duration(66.160ns) Time(282.000ns) Timestamp(18.524 845 722)
According to Windows driver, no ZLP is needed if wBlockLength is non-zero,
because the non-zero wBlockLength has already told the function side the
size of transfer to be expected. However, there are in-market NCM devices
that rely on ZLP as long as the wBlockLength is multiple of wMaxPacketSize.
To deal with such devices, it pads an extra 0 at end so the transfer is no
longer multiple of wMaxPacketSize.
Cc: <stable@vger.kernel.org>
Fixes: 9f6ce4240a ("usb: gadget: f_ncm.c added")
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Maciej Żenczykowski <maze@google.com>
Link: https://lore.kernel.org/r/20240205074650.200304-1-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The reverted commit makes the state machine only ever go from SRC_ATTACH_WAIT
to SNK_TRY in endless loop when toggling. After revert it goes to SRC_ATTACHED
after initially trying SNK_TRY earlier, as it should for toggling to ever detect
the power source mode and the port is again able to provide power to attached
power sinks.
This reverts commit 2d6d801270.
Cc: stable@vger.kernel.org
Fixes: 2d6d801270 ("usb: typec: tcpm: reset counter when enter into unattached state after try role")
Signed-off-by: Ondrej Jirman <megi@xff.cz>
Link: https://lore.kernel.org/r/20240217162023.1719738-1-megi@xff.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When upgrading from 6.1 LTS to 6.6 LTS, I noticed the ethernet gadget
stopped working on Palm TE.
Commit 8825acd7cc ("ARM: omap1: remove dead code") deleted Palm TE from
machine_without_vbus_sense(), although the board is still used. Fix that.
Fixes: 8825acd7cc ("ARM: omap1: remove dead code")
Cc: stable <stable@kernel.org>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20240217192042.GA372205@darkstar.musicnaut.iki.fi
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
829 if (request->complete) {
830 spin_unlock(&priv_dev->lock);
831 usb_gadget_giveback_request(&priv_ep->endpoint,
832 request);
833 spin_lock(&priv_dev->lock);
834 }
835
836 if (request->buf == priv_dev->zlp_buf)
837 cdns3_gadget_ep_free_request(&priv_ep->endpoint, request);
Driver append an additional zero packet request when queue a packet, which
length mod max packet size is 0. When transfer complete, run to line 831,
usb_gadget_giveback_request() will free this requestion. 836 condition is
true, so cdns3_gadget_ep_free_request() free this request again.
Log:
[ 1920.140696][ T150] BUG: KFENCE: use-after-free read in cdns3_gadget_giveback+0x134/0x2c0 [cdns3]
[ 1920.140696][ T150]
[ 1920.151837][ T150] Use-after-free read at 0x000000003d1cd10b (in kfence-#36):
[ 1920.159082][ T150] cdns3_gadget_giveback+0x134/0x2c0 [cdns3]
[ 1920.164988][ T150] cdns3_transfer_completed+0x438/0x5f8 [cdns3]
Add check at line 829, skip call usb_gadget_giveback_request() if it is
additional zero length packet request. Needn't call
usb_gadget_giveback_request() because it is allocated in this driver.
Cc: stable@vger.kernel.org
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20240202154217.661867-2-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a possibility that usb_role_switch device is unregistered before
the user put usb_role_switch. In this case, the user may still want to
get/set_role() since the user can't sense the changes of usb_role_switch.
This will add a flag to show if usb_role_switch is already registered and
avoid unwanted behaviors.
Fixes: fde0aa6c17 ("usb: common: Small class for USB role switches")
cc: stable@vger.kernel.org
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240129093739.2371530-2-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In current design, usb role class driver will get usb_role_switch parent's
module reference after the user get usb_role_switch device and put the
reference after the user put the usb_role_switch device. However, the
parent device of usb_role_switch may be removed before the user put the
usb_role_switch. If so, then, NULL pointer issue will be met when the user
put the parent module's reference.
This will save the module pointer in structure of usb_role_switch. Then,
we don't need to find module by iterating long relations.
Fixes: 5c54fcac9a ("usb: roles: Take care of driver module reference counting")
cc: stable@vger.kernel.org
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240129093739.2371530-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cadence have several controllers from 0x000403xx family but current
driver suuport detecting only one with DID equal 0x0004034E.
It causes that if someone uses different CDNSP controller then driver
will use incorrect version and register space.
Patch fix this issue.
cc: stable@vger.kernel.org
Fixes: 3d82904559 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Link: https://lore.kernel.org/r/20240215121609.259772-1-pawell@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
host.c file has some parts of code that were introduced for CDNS3 driver
and should not be used with CDNSP driver.
This patch blocks using these parts of codes by CDNSP driver.
These elements include:
- xhci_plat_cdns3_xhci object
- cdns3 specific XECP_PORT_CAP_REG register
- cdns3 specific XECP_AUX_CTRL_REG1 register
cc: stable@vger.kernel.org
Fixes: 3d82904559 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Link: https://lore.kernel.org/r/20240206104018.48272-1-pawell@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes relying upon linux/of_platform.h to include
linux/platform_device.h, which it no longer does, thereby fixing
compilation problems like:
In file included from drivers/usb/host/uhci-hcd.c:850:
drivers/usb/host/uhci-grlib.c: In function 'uhci_hcd_grlib_probe':
drivers/usb/host/uhci-grlib.c:92:29: error: invalid use of undefined type 'struct platform_device'
92 | struct device_node *dn = op->dev.of_node;
| ^~
Fixes: ef175b29a2 ("of: Stop circularly including of_device.h and of_platform.h")
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Link: https://lore.kernel.org/r/20240129075056.1511630-1-andreas@gaisler.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PMI632 PMIC support Type-C port handling, but lacks USB
PowerDelivery support. The TCPM requires all callbacks to be provided
by the implementation. Implement a special, 'stub' Qcom PD PHY
implementation to enable the PMI632 support.
Acked-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Luca Weiss <luca.weiss@fairphone.com> # sdm632-fairphone-fp3
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240130-pmi632-typec-v3-3-b05fe44f0a51@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PD major revision for the port partner is described in
GET_CONNECTOR_CAPABILITY and is only valid on UCSI 2.0 and newer. Update
the pd_revision on the partner if the UCSI version is 2.0 or newer.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Prashant Malani <pmalani@chromium.org>
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Link: https://lore.kernel.org/r/20240209143723.v5.3.Idf7d373c3cbb54058403cb951d644f1f09973d15@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update the data structures for ucsi_connector_capability and
ucsi_connector_status to UCSIv3.
Reviewed-by: Prashant Malani <pmalani@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Link: https://lore.kernel.org/r/20240209143723.v5.2.I3d909e3c9a200621e3034686f068a3307945fd87@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Between UCSI 1.2 and UCSI 2.0, the size of the MESSAGE_IN region was
increased from 16 to 256. In order to avoid overflowing reads for older
systems, add a mechanism to use the read UCSI version to truncate read
sizes on UCSI v1.2.
Tested-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Prashant Malani <pmalani@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Link: https://lore.kernel.org/r/20240209143723.v5.1.Iacf5570a66b82b73ef03daa6557e2fc0db10266a@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If an frame was transmitted incomplete to the host, we set the
UVC_STREAM_ERR bit in the header for the last request that is going
to be queued. This way the host will know that it should drop the
frame instead of trying to display the corrupted content.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20240214-uvc-error-tag-v1-2-37659a3877fe@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the request that was missed was zero bytes long, it
is likely that the overall transferred frame was not affected.
So don't flag the frame incomplete in that case.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20240214-uvc-error-tag-v1-1-37659a3877fe@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We refactor the complete handler since the return path with the
locking are really difficult to follow. Just simplify the function by
switching the logic return it on an disabled endpoint early. This way
the second level of indentation can be removed.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20240214-uvc-gadget-cleanup-v1-3-de6d78780459@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pump function is running in an while(1) loop. The only case this
loop will be escaped is the two breaks. In both cases the req is valid.
Therefor the check for an not set req can be dropped and setting the req
to NULL does also has never any effect.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20240214-uvc-gadget-cleanup-v1-1-de6d78780459@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is probable useful information to have in user space in
general, but it's primarily needed for the xHCI DbC (Debug
Capability). When xHCI DbC is being used, the USB port needs
to be muxed to the xHCI even in device role. In xHCI DbC mode,
the xHCI is the USB device controller.
Tested-by: Uday Bhat <uday.m.bhat@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Prashant Malani <pmalani@chromium.org>
Link: https://lore.kernel.org/r/20240213130018.3029991-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The variable retval is being assigned a value that is not being read
and is being re-assigned a new value a couple of statements later.
The assignment is redundant and can be removed.
Cleans up clang scan warning:
drivers/usb/image/mdc800.c:634:2: warning: Value stored to 'retval'
is never read [deadcode.DeadStores]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20240207113730.2444296-1-colin.i.king@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The variable offset is being assigned a value that is not being read
afterwards, the assignment is redundant and can be removed.
Cleans up clang scan warning:
drivers/usb/storage/freecom.c:537:2: warning: Value stored to 'offset'
is never read [deadcode.DeadStores]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20240207112208.2443237-1-colin.i.king@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace the self-rolled implementations with kstrtobool(). This reduces
the maintenance efforts in the future.
Signed-off-by: Guan-Yu Lin <guanyulin@google.com>
Link: https://lore.kernel.org/r/20240202030301.2396374-1-guanyulin@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch introduces three new ioctls. They all should be called on a
data endpoint (ie. not ep0). They are:
- FUNCTIONFS_DMABUF_ATTACH, which takes the file descriptor of a DMABUF
object to attach to the endpoint.
- FUNCTIONFS_DMABUF_DETACH, which takes the file descriptor of the
DMABUF to detach from the endpoint. Note that closing the endpoint's
file descriptor will automatically detach all attached DMABUFs.
- FUNCTIONFS_DMABUF_TRANSFER, which requests a data transfer from / to
the given DMABUF. Its argument is a structure that packs the DMABUF's
file descriptor, the size in bytes to transfer (which should generally
be set to the size of the DMABUF), and a 'flags' field which is unused
for now.
Before this ioctl can be used, the related DMABUF must be attached
with FUNCTIONFS_DMABUF_ATTACH.
These three ioctls enable the FunctionFS code to transfer data between
the USB stack and a DMABUF object, which can be provided by a driver
from a completely different subsystem, in a zero-copy fashion.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Christian König <christian.koenig@amd.com>
Link: https://lore.kernel.org/r/20240130122340.54813-4-paul@crapouillou.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a new 'sg_was_mapped' field to the struct usb_request. This field
can be used to indicate that the scatterlist associated to the USB
transfer has already been mapped into the DMA space, and it does not
have to be done internally.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20240130122340.54813-2-paul@crapouillou.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove 'snps,host-vbus-glitches-quirk' and apply workaround
unconditionally.
It is safer to keep vbus disabled before handing over to xhci driver. So
needn't 'snps,host-vbus-glitches' property to enable it and apply it
unconditionally.
Remove all host_vbus_glitches variable and call
dwc3_power_off_all_roothub_ports() directly.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240212-vbus-glitch-v2-2-d71b73a82de1@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pointer trb is being assigned a value that is not being
read afterwards, it is being re-assigned later inside a for_each_sg
loop. The assignment is redundant and can be removed.
Cleans up clang scan warning:
drivers/usb/dwc3/gadget.c:3432:19: warning: Value stored to 'trb'
during its initialization is never read [deadcode.DeadStores]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240207120319.2445123-1-colin.i.king@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver dwc3 deviates from the programming guide in regard to
endpoint configuration. It does this command sequence:
DEPSTARTCFG -> DEPXFERCFG -> DEPCFG
Instead of the suggested flow:
DEPSTARTCFG -> DEPCFG -> DEPXFERCFG
The reasons for this deviation were as follow, quoted:
1) The databook says to do %DWC3_DEPCMD_DEPSTARTCFG for every
%USB_REQ_SET_CONFIGURATION and %USB_REQ_SET_INTERFACE
(8.1.5). This is incorrect in the scenario of multiple
interfaces.
2) The databook does not mention doing more
%DWC3_DEPCMD_DEPXFERCFG for new endpoint on alt setting
(8.1.6).
Regarding 1), DEPSTARTCFG resets the endpoints' resource and can be a
problem if used with SET_INTERFACE request of a multiple interface
configuration. But we can still satisfy the programming guide
requirement by assigning the endpoint resource as part of
usb_ep_enable(). We will only reset endpoint resources on controller
initialization and SET_CONFIGURATION request.
Regarding 2), the later versions of the programming guide were updated
to clarify this flow (see "Alternate Initialization on SetInterface
Request" of the programming guide). As long as the platform has enough
physical endpoints, we can assign resource to a new endpoint.
The order of the command sequence will not be a problem to most
platforms for the current implementation of the dwc3 driver. However,
this order is required in different scenarios (such as initialization
during controller's hibernation restore). Let's keep the flow consistent
and follow the programming guide.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/c143583a5afb087deb8c3aa5eb227ee23515f272.1706754219.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Expose xhci_stop_endpoint_sync() which is a synchronous variant of
xhci_queue_stop_endpoint(). This is useful for client drivers that are
using the secondary interrupters, and need to stop/clean up the current
session. The stop endpoint command handler will also take care of cleaning
up the ring.
Modifications to repurpose the new API into existing stop endpoint
sequences was implemented by Wesley Cheng.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Co-developed-by: Wesley Cheng <quic_wcheng@quicinc.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240217001017.29969-11-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some sequences, will require traversing through the entire event ring
without handling the event TRB. This is ideal for when secondary
interrupters that are utilized by external entities need to clean up the
interrupter's event rings during halting of the XHCI HCD.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240217001017.29969-10-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check if the event ring exists and is valid once when the event handler
is called, not before every individual event TRB.
At this point the interrupter is valid, so no need to check that.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240217001017.29969-9-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add unhandled_event_trb() that returns true in case xHC hardware has
written new event trbs to the event ring that driver has not yet handled.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240217001017.29969-8-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Split the main XHCI interrupt handler into a different API, so that other
potential interrupters can utilize similar event ring handling. A scenario
would be if a secondary interrupter required to skip pending events in the
event ring, which would warrant a similar set of operations.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240217001017.29969-7-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The event ring dequeue pointer field (ERDP) in xHC hardware is used to
inform controller how far the driver has processed events on the event
ring.
In the case all events are handled and event ring is empty then the
address of the TRB after the last processed one should be written.
This TRB is both the enqueue and dequeue pointer.
But in case we are writing the ERDP in the middle of processing
several events then ERDP field should be written with the "up to and
including" address of the last handled event TRB.
Currenly each ERDP write by driver is done as if all events are handled
and ring is empty.
Fix this by adjusting the order when software dequeue "inc_deq()"
is called and hardware dequeue "xhci_update_erst_dequeue()" is updated.
Details in xhci 1.2 specification section 4.9.4:
"System software shall write the Event Ring Dequeue Pointer (ERDP)
register to inform the xHC that it has completed the processing of Event
TRBs up to and including the Event TRB referenced by the ERDP.
The detection of a Cycle bit mismatch in an Event TRB processed by
software indicates the location of the xHC Event Ring Enqueue Pointer
and that the Event Ring is empty. Software shall write the ERDP with
the address of this TRB to indicate that it has processed all Events
in the ring"
This change depends on fixes made to relocate inc_deq() calls captured
in the below commits:
commit 3321f84bfa ("xhci: simplify event ring dequeue tracking for
transfer events")
commit d1830364e9 ("xhci: Simplify event ring dequeue pointer update
for port change events")
Fixes: dc0ffbea57 ("usb: host: xhci: update event ring dequeue pointer on purpose")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240217001017.29969-6-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The event_ring_deq parameter is used to check if the event ring dequeue
position is updated while calling by xhci_handle_event(), meaning there was
an actual event on the ring to handle. In this case the driver needs to
inform hardware about the updated dequeue position.
Basically event_ring_deq just stores the old event ring dequeue position
before calling the event handler.
Keeping track of software event dequeue updates this way is no longer
useful as driver anyways reads the current hardware dequeue position
within the handle event, and checks if it needs to be updated.
The driver might anyway need to modify the EHB (event handler busy) bit in
the same register as the dequeue pointer even if the actual dequeue
position did not change.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240217001017.29969-5-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
isoc_bei_interval is used to balance how often completed isochronous
events cause interrupts. If interval is too large then the event ring
may fill up before the completed isoc TRBs are handled.
isoc_bei_interval is tuned based on how full the event ring is.
isoc_bei_interval variable needs to be per interrupter as
with several interrupters each one has its own event ring.
move isoc_bei_interval variable to the interrupter structure.
if a secondary interrupter does not care about this feature then
keep isoc_bei_interval 0.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240217001017.29969-4-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a helper to set the interrupt moderation interval for an interrupter.
Each interrupter can have its own moderation value.
Hardware has a 16bit register for the moderation value, each step is 250ns.
Helper function imod_interval argument is in nanoseconds.
Values from 0 to 16383750 (250 x 0xffff) are accepted.
0 means no interrupt throttling.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240217001017.29969-3-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Each interrupter has an interrupt pending (IP) bit that should be cleared
in the interrupt handler. This is done automatically for systems using
MSI/MSI-X interrupts.
Secondary interrupters used by audio offload may not actually trigger
MSI/MSI-X messages, so driver may need to clear the IP bit manually for
these, even if the primary interrupter IP is cleared automatically.
Add an ip_autoclear flag to each interrupter that driver can configure
when requesting an interrupt for that xHC interrupter, and move
the interrupt pending clearing code to its own helper function.
Use this ip_autoclear flag instead of the current hcd->msi_enabled
to check if IP flag is cleared by software.
[Moved ip_autoclear into xhci and set based on msi_enabled -wcheng]
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240217001017.29969-2-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It has been observed that some USB/UAS devices return generic properties
hardcoded in firmware for mode pages for a period of time after a device
has been discovered. The reported properties are either garbage or they do
not accurately reflect the characteristics of the physical storage device
attached in the case of a bridge.
Prior to commit 1e029397d1 ("scsi: sd: Reorganize DIF/DIX code to
avoid calling revalidate twice") we would call revalidate several
times during device discovery. As a result, incorrect values would
eventually get replaced with ones accurately describing the attached
storage. When we did away with the redundant revalidate pass, several
cases were reported where devices reported nonsensical values or would
end up in write-protected state.
An initial attempt at addressing this issue involved introducing a
delayed second revalidate invocation. However, this approach still
left some devices reporting incorrect characteristics.
Tasos Sahanidis debugged the problem further and identified that
introducing a READ operation prior to MODE SENSE fixed the problem and that
it wasn't a timing issue. Issuing a READ appears to cause the devices to
update their state to reflect the actual properties of the storage
media. Device properties like vendor, model, and storage capacity appear to
be correctly reported from the get-go. It is unclear why these devices
defer populating the remaining characteristics.
Match the behavior of a well known commercial operating system and
trigger a READ operation prior to querying device characteristics to
force the device to populate the mode pages.
The additional READ is triggered by a flag set in the USB storage and
UAS drivers. We avoid issuing the READ for other transport classes
since some storage devices identify Linux through our particular
discovery command sequence.
Link: https://lore.kernel.org/r/20240213143306.2194237-1-martin.petersen@oracle.com
Fixes: 1e029397d1 ("scsi: sd: Reorganize DIF/DIX code to avoid calling revalidate twice")
Cc: stable@vger.kernel.org
Reported-by: Tasos Sahanidis <tasos@tasossah.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Tasos Sahanidis <tasos@tasossah.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This reverts commit 398aa9a7e7.
The update to the gadget API to support EBC feature is incomplete. It's
missing at least the following:
* New usage documentation
* Gadget capability check
* Condition for the user to check how many and which endpoints can be
used as "fifo_mode"
* Description of how it can affect completed request (e.g. dwc3 won't
update TRB on completion -- ie. how it can affect request's actual
length report)
Let's revert this until it's ready.
Fixes: 398aa9a7e7 ("usb: dwc3: Support EBC feature of DWC_usb31")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/3042f847ff904b4dd4e4cf66a1b9df470e63439e.1707441690.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 8caab75fd2 ("spi: Generalize SPI "master" to "controller"")
some functions and struct members were renamed. To not break all drivers
compatibility macros were provided.
To be able to remove these compatibility macros push the renaming into
this driver.
Reviewed-by: Herve Codina <herve.codina@bootlin.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/5caf03b6f321a9870aabb9282f1f22211d052740.1707324794.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The QCM6490 Linux Android firmware needs this workaround as well. Add it
to the list.
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Link: https://lore.kernel.org/r/20240208-fp5-pmic-glink-v2-2-4837d4abd5a4@fairphone.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The only generic interface to execute asynchronously in the BH context is
tasklet; however, it's marked deprecated and has some design flaws. To
replace tasklets, BH workqueue support was recently added. A BH workqueue
behaves similarly to regular workqueues except that the queued work items
are executed in the BH context.
This patch converts usb hcd from tasklet to BH workqueue.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: linux-usb@vger.kernel.org
Here are some new device ids for 6.8-rc3.
All have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCZb0HUgAKCRALxc3C7H1l
CApxAP9sgKgE0sUvnzn+9/jxR+9+NGkJESBOud/ovI1c1zPIXwEAqJAU5vnfkUWI
VmMw/fTnCs5H0uiN6pbkQnZQ0JT7NgU=
=EIrL
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-6.8-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial device ids for 6.8-rc3
Here are some new device ids for 6.8-rc3.
All have been in linux-next with no reported issues.
* tag 'usb-serial-6.8-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add Fibocom FM101-GL variant
USB: serial: qcserial: add new usb-id for Dell Wireless DW5826e
USB: serial: cp210x: add ID for IMST iM871A-USB
The device IMST USB-Stick for Smart Meter is a rebranded IMST iM871A-USB
Wireless M-Bus USB-adapter. It is used to read wireless water, gas and
electricity meters.
Signed-off-by: Leonard Dallmayr <leonard.dallmayr@mailbox.org>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Follow the PD PHY changes and rework Type-C port implementation to
become an encapsulated backend. While this is not required for the
PMI632, it will us later to enable Type-C handling on earlier platforms,
including, but not limited to SDM845, SDM660 and MSM8998.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Acked-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20240113-pmi632-typec-v2-8-182d9aa0a5b3@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rework Qualcomm PMIC TCPM driver to allow different platform-specific
implementations of the PD PHY interface. While majority of platforms
has the same of register for the PD PHY, some obscure ones (PMI632) do
not have real PD PHY support. Add proper interface between the main
module and the PD PHY backend to allow switching the PD PHY
implementation.
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Acked-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240113-pmi632-typec-v2-7-182d9aa0a5b3@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function qcom_pmic_typec_set_roles() passes enum values as boolean
values to qcom_pmic_typec_pdphy_set_roles(), which then interprets them
as bit values. Be more explicit about it, pass enum values directly and
compute corresponding bit masks in qcom_pmic_typec_pdphy_set_roles().
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20240113-pmi632-typec-v2-6-182d9aa0a5b3@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the PD is disabled for the port, port->pds will be left as NULL,
which causes the following crash during caps intilisation. Fix the
crash.
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
Call trace:
tcpm_register_port+0xaec/0xc44
qcom_pmic_typec_probe+0x1a4/0x254
platform_probe+0x68/0xc0
really_probe+0x148/0x2ac
__driver_probe_device+0x78/0x12c
driver_probe_device+0xd8/0x160
Bluetooth: hci0: QCA Product ID :0x0000000a
__device_attach_driver+0xb8/0x138
bus_for_each_drv+0x80/0xdc
Bluetooth: hci0: QCA SOC Version :0x40020150
__device_attach+0x9c/0x188
device_initial_probe+0x14/0x20
bus_probe_device+0xac/0xb0
deferred_probe_work_func+0x8c/0xc8
process_one_work+0x1ec/0x51c
worker_thread+0x1ec/0x3e4
kthread+0x120/0x124
ret_from_fork+0x10/0x20
Fixes: cd099cde4e ("usb: typec: tcpm: Support multiple capabilities")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240113-pmi632-typec-v2-5-182d9aa0a5b3@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PPM on some Dell laptops seems to expect that the ACK_CC_CI
command to clear the connector change notification is in turn
followed by another ACK_CC_CI to acknowledge the ACK_CC_CI command
itself. This is in violation of the UCSI spec that states:
"The only notification that is not acknowledged by the OPM is
the command completion notification for the ACK_CC_CI or the
PPM_RESET command."
Add a quirk to send this ack anyway.
Apply the quirk to all Dell systems.
On the first command that acks a connector change send a dummy
command to determine if it runs into a timeout. Only activate
the quirk if it does. This ensure that we do not break Dell
systems that do not need the quirk.
Signed-off-by: "Christian A. Ehrhardt" <lk@c--e.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240121204123.275441-4-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of a spurious or otherwise delayed notification it is
possible that CCI still reports the previous completion. The
UCSI spec is aware of this and provides two completion bits in
CCI, one for normal commands and one for acks. As acks and commands
alternate the notification handler can determine if the completion
bit is from the current command.
The initial UCSI code correctly handled this but the distinction
between the two completion bits was lost with the introduction of
the new API.
To fix this revive the ACK_PENDING bit for ucsi_acpi and only complete
commands if the completion bit matches.
Fixes: f56de278e8 ("usb: typec: ucsi: acpi: Move to the new API")
Cc: stable@vger.kernel.org
Signed-off-by: "Christian A. Ehrhardt" <lk@c--e.de>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240121204123.275441-3-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Calling ->sync_write must be done while holding the PPM lock as
the mailbox logic does not support concurrent commands.
At least since the addition of partner task this means that
ucsi_acknowledge_connector_change should be called with the
PPM lock held as it calls ->sync_write.
Thus protect the only call to ucsi_acknowledge_connector_change
with the PPM. All other calls to ->sync_write already happen
under the PPM lock.
Fixes: b9aa02ca39 ("usb: typec: ucsi: Add polling mechanism for partner tasks like alt mode checking")
Cc: stable@vger.kernel.org
Signed-off-by: "Christian A. Ehrhardt" <lk@c--e.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240121204123.275441-2-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ULPI per-device debugfs root is named after the ulpi device's
parent, but ulpi_unregister_interface tries to remove a debugfs
directory named after the ulpi device itself. This results in the
directory sticking around and preventing subsequent (deferred) probes
from succeeding. Change the directory name to match the ulpi device.
Fixes: bd0a0a024f ("usb: ulpi: Add debugfs support")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/20240126223800.2864613-1-sean.anderson@seco.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 1e35f07439.
Given that ERROR_RECOVERY calls into PORT_RESET for Hi-Zing
the CC pins, setting CC pins to default state during PORT_RESET
breaks error recovery.
4.5.2.2.2.1 ErrorRecovery State Requirements
The port shall not drive VBUS or VCONN, and shall present a
high-impedance to ground (above zOPEN) on its CC1 and CC2 pins.
Hi-Zing the CC pins is the inteded behavior for PORT_RESET.
CC pins are set to default state after tErrorRecovery in
PORT_RESET_WAIT_OFF.
4.5.2.2.2.2 Exiting From ErrorRecovery State
A Sink shall transition to Unattached.SNK after tErrorRecovery.
A Source shall transition to Unattached.SRC after tErrorRecovery.
Cc: stable@vger.kernel.org
Cc: Frank Wang <frank.wang@rock-chips.com>
Fixes: 1e35f07439 ("usb: typec: tcpm: fix cc role at port reset")
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20240117114742.2587779-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a USB gadget is configured through configfs with 1 or more f_fs
functions, then the logic setting up the gadget configuration has to wait
until the user space code (typically separate applications) responsible for
those functions have written their descriptors before the gadget can be
activated.
The f_fs instance already knows if this has been done, so expose it through
a "ready" attribute in configfs for easier synchronization.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Link: https://lore.kernel.org/r/20240126203208.2482573-1-peter@korsgaard.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When DWC3 is set to host mode by programming register DWC3_GCTL, VBUS
(or its control signal) will be turned on immediately on related Root Hub
ports. Then, the VBUS is turned off for a little while(15us) when do xhci
reset (conducted by xhci driver) and back to normal finally, we can
observe a negative glitch of related signal happen.
This VBUS glitch might cause some USB devices enumeration fail if kernel
boot with them connected. Such as LS1012AFWRY/LS1043ARDB/LX2160AQDS
/LS1088ARDB with Kingston 16GB USB2.0/Kingston USB3.0/JetFlash Transcend
4GB USB2.0 drives. The fail cases include enumerated as full-speed device
or report wrong device descriptor, etc.
One SW workaround which can fix this is by programing all xhci PORTSC[PP]
to 0 to turn off VBUS immediately after setting host mode in DWC3 driver
(per signal measurement result, it will be too late to do it in
xhci-plat.c or xhci.c). Then, after xhci reset complete in xhci driver,
PORTSC[PP]s' value will back to 1 automatically and VBUS on at that time,
no glitch happen and normal enumeration process has no impact.
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240124152525.3910311-4-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Split the PORT and CAPs macro definitions into a separate file to
facilitate sharing with other files without the need to include the entire
xhci.h.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240124152525.3910311-2-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement active cable VDM support for SOP' according to the DisplayPort
Alt Mode 2.0 specification.
When probing the DisplayPort driver, the state machine will transition to
Enter Mode on SOP' if an active cable altmode is detected. The SVDM flow
is as followed:
(1) Enter Mode SOP'
(2) Enter Mode SOP
(3) Status Update SOP
(4) Configure SOP'
(5) Configure SOP
Status Update on SOP' after Enter Mode is optional and not implemented for
now. When exiting the alt mode, send Exit Mode over SOP' after SOP.
Should an altmode vdm fail on SOP', the DisplayPort driver will drop its
reference to the plug and attempt to continue in SOP operation.
Add new dp_state enums DP_STATE_ENTER_PRIME, DP_STATE_CONFIGURE_PRIME, and
DP_STATE_EXIT_PRIME. dp_altmode adds typec_displayport_data for the cable
plug to store the plug configuration and adds a typec_altmode reference
for the cable plug.
dp_altmode_configure takes the cable pin assignment capabilities into
account when deciding on pin configuration. dp_altmode_configure_vdm_cable
sends the configure message on SOP'.
dp_altmode_activate now attempts to enter on SOP' if applicable, and will
attempt to enter on SOP on failure.
dp_cable_altmode_vdm handles VDMs passed to the DisplayPort driver from
the tcpm.
Signed-off-by: RD Babiera <rdbabiera@google.com>
Link: https://lore.kernel.org/r/20240108191620.987785-26-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add tcpm_cable_ops for enter, exit, and vdm to the tcpm, which are
registered after registering port alt modes through
typec_port_register_cable_ops. Enter Mode on SOP' now sends Exit Mode upon
failure to report to the driver.
tcpm_queue_vdm_unlocked now takes sop type as input. Proper adev_actions
in tcpm_pd_svdm are selected for SOP' messages.
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240108191620.987785-25-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds Discover SVIDs and Discover Modes support for SOP' and Alt Mode
SVDM support over SOP'. tcpm_port adds separate Alt Mode data for SOP'.
svdm_consume_svids and svdm_consume_modes take the received SVDM's SOP*
type to store svids/modes separately, and tcpm_register_plug_altmodes
registers the active cable's alt modes.
In tcpm_pd_svdm, the port will send Discover SVIDs to SOP' after Discover
Modes on SOP if the connected cable is an active cable. Discover Modes on
SOP' is sent following Discover SVIDs on SOP. Registering partner alt modes
is delayed when an active cable is present until Discover Modes completes
on SOP', or if the Discover SVIDs/Discover Modes request on SOP' encounters
a transmission error.
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240108191620.987785-24-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SRC_VDM_IDENTITY_REQUEST state which first enters after SRC_STARTUP.
The state sends Discover Identity on SOP' and transitions to
SRC_SEND_CAPABILITIES. SRC_SEND_CAPABILITIES will transition back into
SRC_VDM_IDENTITY_REQUEST instead of retrying immediately.
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240108191620.987785-23-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add data message handling and Discover Identity SVDM over SOP'
This patch contains the following changes:
1. pd_vdo
Add VDO indices for active and passive cables, documentation to reflect
expected number of objects depending on PD Revision, and macro to indicate
port parter is data host capable.
2. tcpm
Add typec_cable and typec_plug to tcpm_port to maintain cable and plug
information. tcpm_port also adds send_discover_prime to indicate that
Discover Identity should be sent out of the ready state.
tcpm_queue_vdm and tcpm_send_vdm now take the SOP* type when transmitting
messages. tcpm_handle_vdm_request and tcpm_pd_svdm also use the SOP* type.
tcpm_pd_svdm handles Discover Identity messages for SOP and SOP'. In the
SOP case, the port uses tcpm_attempt_vconn_swap_discovery to determine if
a Vconn swap is needed for cable communication. Otherwise, the port will
send Discover Identity on SOP' if it can, or default to Discover SVIDs.
svdm_consume_identity_sop_prime consumes the result of Discover Identity
on SOP'. It fills out cable identity and description, and it registers
the cable. The SOP' plug is registered as well.
The VDM state machine is adjusted to construct messages based on the SOP*
type. If a transmission error occurs after the max number of retries for
Discover Identity over SOP', then the port will send Discover SVIDs over
SOP.
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240108191620.987785-22-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add attempt_vconn_swap_discovery callback to determine whether the TCPM
should perform a Vconn swap following Discover Identity on SOP. The tcpci
will return false unless chip level drivers implement the callback.
Maxim based TCPCs will return true unless the last connection resulted in
a Vconn Over Current Fault, which may be the result of the Vconn swap. In
addition to the port resetting, the TCPCI will veto the next Vconn swap
from occurring.
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240108191620.987785-21-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add tx_sop_type to tcpm_pd_send_control and rx_sop_type to
tcpm_pd_ctrl_request. TCPC_TX_SOP is added to all pd_send_control calls,
but TCPC_TX_SOP_PRIME is added to pd_send_control for a SOFT_RESET message
sent after a Vconn swap that makes the Port the Vconn source. Likewise,
tcpm_pd_ctrl_request resets the proper protocol layer depending on
rx_sop_type for SOFT_RESET.
VCONN_SWAP_TURN_ON_VCONN now moves to a new state,
VCONN_SWAP_SEND_SOFT_RESET. This state sends SOFT_RESET over SOP' before
transitioning to the ready state if applicable. It transitions after
PD_T_VCONN_STABLE, definied in pd.h as the time required for Vconn to be
on before transmitting messages.
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240108191620.987785-20-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add negotiated revision and tx/rx message ids to tcpm_port specific to
SOP'. tx_sop_type is added to the tcpm_port to determine whether the
current constructed message will be sent over SOP or SOP' if not
sent immediately.
tcpm_pd_rx_handler updates the received message ids. SOP* messages are not
processed afterwards. The handler also calls tcpm_can_communicate_sop_prime
to determine if a SOP' message is directed towards the port, and drops SOP'
messages it should not respond to.
tcpm_can_communicate_sop_prime is added as a helper to determine whether
the port is capable of communicating over SOP' at a given moment. Being
the Vconn source is a requirement in Power Delivery 3.0 but only a
recommendation in Power Delviery 2.0. Because the port should ensure that
the cable is powered before communication, always enforce the port is the
Vconn source regardless of revision.
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240108191620.987785-19-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tcpm_pd_receive adds the SOP type as a parameter, and passes it within the
pd_rx_event struct for tcpm_pd_rx_handler to use. For now, the handler
drops all SOP' messages.
Maxim based tcpci drivers are capable of SOP' communication, so process_rx
now takes the SOP type into account and passes the value to
tcpm_pd_receive.
tcpci_set_pd_rx now utilizes the cable_comm_capable flag to determine if
TCPC_RX_DETECT_SOP1 should be added to the bitfield when enabling PD
message reception.
For all other consumers of tcpm_pd_receive, default the new field to
TCPC_TX_SOP.
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240108191620.987785-18-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add cable_comm_capable to tcpci_data for tcpci drivers to indicate that
the port tcpc is capable of communicating to cables over SOP. A
corresponding tcpci callback tcpci_cable_comm_capable returns this value.
The tcpm will primarily use this in later patches to determine if the port
can transmit and receive SOP' messages.
Maxim based tcpci drivers are capable of SOP' communication, so the
cable_comm_capable flag is set to true.
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240108191620.987785-17-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add typec_cable_set_svdm_version and typec_get_cable_svdm version symbols.
Cables can operate under a lower PD revision than the port partner, and the
max SVDM version is tied to the PD revision. So, typec_cable maintains its
own svdm_version.
Add typec_altmode_get_cable_svdm_version to return the cable's negotiated
svdm_version for altmode drivers to use.
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240108191620.987785-16-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add typec_cable_ops struct for enter, exit, and vdm. The struct is added
to typec_altmode so port alt modes can have access to partner and cable
specific callbacks, and alt mode drivers can specify operations over SOP'
and SOP'' without modifying the existing API.
typec_port_register_cable_ops is added as a new symbol for port drivers
to use to register cable operations to their registered port alt modes.
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240108191620.987785-15-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
