The minimum baud rate supported by this driver is 0, so even for the B0
case, uart_get_baud_rate() will return 9600, not zero. This check predates
commit 16ae2a877b ("serial: Fix crash if the minimum rate of the device
is > 9600 baud") and is no longer necessary so remove it.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20260410152022.2146488-3-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The minimum baud rate supported by this driver is 300, so even for the B0
case, uart_get_baud_rate() will return 9600, not zero. This check predates
commit 16ae2a877b ("serial: Fix crash if the minimum rate of the device
is > 9600 baud") and is no longer necessary so remove it.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20260410152022.2146488-2-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When uart_flush_buffer() runs before the DMA completion IRQ is delivered,
the following race can occur (all steps serialized by uart_port_lock):
1. DMA starts: tx_remaining = N, kfifo contains N bytes
2. DMA completes in hardware; IRQ is pending but not yet delivered
3. uart_flush_buffer() acquires the port lock and calls kfifo_reset(),
making kfifo_len() = 0 while tx_remaining remains N
4. uart_flush_buffer() releases the port lock
5. DMA IRQ fires; handle_tx_dma() acquires the port lock and calls
uart_xmit_advance(uport, tx_remaining) on an empty kfifo
uart_xmit_advance() increments kfifo->out by tx_remaining. Since
kfifo_reset() already set both in and out to 0, out wraps past in,
causing kfifo_len() to return UART_XMIT_SIZE - tx_remaining. The next
start_tx_dma() call then submits a DMA transfer of stale buffer data.
Fix this by snapshotting kfifo_len() at the start of handle_tx_dma()
and skipping uart_xmit_advance() when fifo_len < tx_remaining, which
indicates the kfifo was reset by a preceding flush.
Fixes: 2aaa43c707 ("tty: serial: qcom-geni-serial: add support for serial engine DMA")
Cc: stable <stable@kernel.org>
Signed-off-by: Viken Dadhaniya <viken.dadhaniya@oss.qualcomm.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Link: https://patch.msgid.link/20260506-serial-dma-stale-tx-buf-v1-1-e3ccb360d719@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
lpuart_start_rx_dma() allocates sport->rx_ring.buf with kzalloc() and
then maps a scatterlist via dma_map_sg(). On three subsequent error
paths the function returns directly without releasing those resources:
- when dma_map_sg() returns 0 (-EINVAL):
ring->buf is leaked.
- when dmaengine_slave_config() fails:
ring->buf and the DMA mapping are leaked.
- when dmaengine_prep_dma_cyclic() returns NULL:
ring->buf and the DMA mapping are leaked.
The sole cleanup path, lpuart_dma_rx_free(), is only reached when
lpuart_dma_rx_use is set, and the caller lpuart_rx_dma_startup() clears
that flag on failure of lpuart_start_rx_dma(). So these resources are
permanently leaked on every failure in this function. Repeated port
open/close or termios changes under error conditions will slowly consume
memory and leave stale streaming DMA mappings behind.
Fix it by introducing two error labels that unmap the scatterlist and
free the ring buffer as appropriate. While here, replace the misleading
-EFAULT (bad userspace pointer) returned when dmaengine_prep_dma_cyclic()
fails with the more accurate -ENOMEM, matching how other dmaengine users
in the tree treat this failure.
No functional change on the success path.
Fixes: 5887ad43ee ("tty: serial: fsl_lpuart: Use cyclic DMA for Rx")
Cc: stable <stable@kernel.org>
Signed-off-by: Shitalkumar Gandhi <shitalkumar.gandhi@cambiumnetworks.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260420135903.2062024-1-shitalkumar.gandhi@cambiumnetworks.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UART_RX_PAR_EN is incorrectly defined as bit 3, which triggers false
framing errors (S_GP_IRQ_1_EN) and causes received data to be dropped
when parity is enabled and the parity bit is 0.
Define UART_RX_PAR_EN as bit 4 of the SE_UART_RX_TRANS_CFG register, as
specified in the reference manual.
Fixes: c4f528795d ("tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP")
Cc: stable <stable@kernel.org>
Signed-off-by: Prasanna S <prasanna.s@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://patch.msgid.link/20260428-serial-bit-correct-v1-1-9131ad5b97d8@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sci_request_port() function uses request_mem_region() to reserve
I/O memory, but in the error path when sci_remap_port() fails, it
incorrectly calls release_resource() instead of release_mem_region().
This mismatch can cause resource accounting issues. Fix it by using
the correct release function, consistent with sci_release_port().
Fixes: e265164708 ("serial: sh-sci: Handle port memory region reservations.")
Cc: stable <stable@kernel.org>
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Closes: https://lore.kernel.org/r/202604032356.SzEjYkBC-lkp@intel.com/
Signed-off-by: Hongling Zeng <zenghongling@kylinos.cn>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260421065737.724187-1-zenghongling@kylinos.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a check for dma_alloc_coherent() failure to prevent a potential
NULL pointer dereference in dma_handle_rx(). Properly release DMA
channels and the PCI device reference using a goto ladder if the
allocation fails.
Fixes: 3c6a483275 ("Serial: EG20T: add PCH_UART driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Zhaoyang Yu <2426767509@qq.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/tencent_E328416B7CFD436F6029F2DF02AD7ED89C08@qq.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix a thinko in the status interrupt handler that has caused counters
for the RI and DSR modem line transitions to be used for the other line
each.
Fixes: 8b4a40809e ("zs: move to the serial subsystem")
Cc: stable <stable@kernel.org>
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://patch.msgid.link/alpine.DEB.2.21.2604101747110.29980@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UltraRISC DP1000 UART does not provide the standard CPR register used
by 8250_dw to discover port capabilities.
Provide a fixed CPR value for the DP1000-specific compatible so the
driver can configure the port correctly.
Signed-off-by: Jia Wang <wangjia@ultrarisc.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://patch.msgid.link/20260429-ultrarisc-serial-v7-4-e475cce9e274@ultrarisc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace the magic CPR value for Renesas RZ/N1 with a composition using
DW_UART_CPR_* bit/field definitions and FIELD_PREP_CONST().
Introduce a helper macro to convert a FIFO size (bytes) into the CPR
FIFO_MODE field value, with BUILD_BUG_ON_ZERO() checks for alignment and
bounds. Use it to replace the literal FIFO_MODE values in the RZN1.
Signed-off-by: Jia Wang <wangjia@ultrarisc.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://patch.msgid.link/20260429-ultrarisc-serial-v7-2-e475cce9e274@ultrarisc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the DW_UART_* register offsets and CPR bit/field definitions from
8250_dwlib.c into 8250_dwlib.h so they can be shared by 8250_dw and
8250_dwlib users.
Add an include guard for 8250_dwlib.h.
Signed-off-by: Jia Wang <wangjia@ultrarisc.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://patch.msgid.link/20260429-ultrarisc-serial-v7-1-e475cce9e274@ultrarisc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rather than using the UPF_CONS_FLOW bit of uart_port.flags to track
the user configuration of console flow control, use the newly added
uart_port.cons_flow (via its getter/setter functions).
A coccinelle script was used to perform the search/replace.
Note1: The sh-sci driver is blindly copying platform data configuration
flags to uart_port.flags. Thus UPF_CONS_FLOW could get set for
uart_port.flags. A follow-up commit will address this.
Note2: The samsung_tty driver is using UPF_CONS_FLOW as a platform data
configuration flag. However, the driver explicitly checks for
this configuration flag and thus setting UPF_CONS_FLOW in
uart_port.flags is avoided.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://patch.msgid.link/20260506121606.5805-3-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver doesn't use the driver_data field, so drop the assigment
together with the then redundant zero assigment for .class and
.class_mask. Also drop the zero in the list terminator.
While at it also use PCI_VDEVICE() to allow dropping "PCI_VENDOR_ID_".
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/20260505084749.2304121-2-u.kleine-koenig@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
... and PCI device helpers.
The various struct pci_device_id were defined using a mixture of
initialization by position and by name. Some use the PCI device helpers
(like PCI_DEVICE and PCI_DEVICE_SUB) and others don't.
Consistently use named initializers, drop assignments of 0 by position
for .class and .class_mask and use the PCI device helpers. Also use
consistent line-breaks and positioning for opening and closing curly
braces.
The secret plan is to make struct pci_device_id::driver_data an
anonymous union (similar to
https://lore.kernel.org/all/cover.1776579304.git.u.kleine-koenig@baylibre.com/)
and that requires named initializers. But it's also a nice cleanup on
its own.
This patch doesn't change the compiled result; this was verified using
an allmodconfig with several things disabled that make reproducible
builds harder on x86 and arm64.
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/20260428144033.1037617-2-u.kleine-koenig@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The synclink_gt driver was marked as broken in commit 426263d5fb
("tty: synclink_gt: mark as BROKEN") in July 2023 because it had severe
structural problems and there had been no evidence of users since 2016.
Since then, no meaningful improvements have been made to the driver,
and it is unlikely that will ever happen due to the lack of interest.
Drop the driver and references to it in comments and documentation.
include/uapi/linux/synclink.h is also removed. The only use of this
header I have found is the linux-raw-sys Rust crate. It generates
bindings for all UAPI headers, but has a hardcoded list of headers and
ioctls, including this one, so that does not indicate that anyone is
using it. I have sent a pull request to remove the include and ioctl
definitions for this header (see the link below).
Link: https://github.com/sunfishcode/linux-raw-sys/pull/185
Signed-off-by: Ethan Nelson-Moore <enelsonmoore@gmail.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Link: https://patch.msgid.link/20260504031519.18877-1-enelsonmoore@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
My MIPS Alchemy systems generate the following warning during
probe of the 8250 driver:
WARNING: drivers/tty/serial/8250/8250_port.c:462 at set_io_from_upio+0xfc/0x124, CPU#0: swapper/0/1
Unsupported UART type 4
[...]
[<80521d40>] set_io_from_upio+0xfc/0x124
[<80521dfc>] serial8250_set_defaults+0x94/0xe0
[<80520fb4>] serial8250_register_8250_port+0x288/0x51c
[<805214ec>] serial8250_probe+0x160/0x1e8
[<8053b5f0>] platform_probe+0x64/0x90
The least invasive fix is to recognize UPIO_AU (type 4) in set_io_from_upio()
and do nothing, since all parameters have already been set up in
8250_rt288x.c::au_platform_setup().
Run-tested on Alchemy Au1300 platform.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Link: https://patch.msgid.link/20260430135822.905035-1-manuel.lauss@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The GPIO_LINE_DIRECTION_* definitions have just recently been exposed to
gpio consumers.h by breaking them out in a separate defs.h file.
Use this to validate the gpio direction instead of the hard-coded literal.
Signed-off-by: Nikola Z. Ivanov <zlatistiv@gmail.com>
Link: https://patch.msgid.link/20260426214250.781151-1-zlatistiv@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add ACPI support to 8250_mtk driver. This makes it possible to
use UART on ARM-based desktops with EDK2 UEFI firmware.
Signed-off-by: Yenchia Chen <yenchia.chen@mediatek.com>
Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Link: https://patch.msgid.link/20260423062345.2473300-2-zhiyong.tao@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Various names for Qualcomm as a company are used in user-visible config
options: QCOM, Qualcomm and Qualcomm Technologies. Switch to unified
"Qualcomm" so it will be easier for users to identify the options when
for example running menuconfig.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://patch.msgid.link/20260427070052.18097-2-krzysztof.kozlowski@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In C, bitfields are not necessarily safe to modify from multiple
threads without locking. Switch "of_node_reused" over to the "flags"
field so modifications are safe.
Cc: Johan Hovold <johan@kernel.org>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Rafael J. Wysocki (Intel) <rafael@kernel.org>
Reviewed-by: Danilo Krummrich <dakr@kernel.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Johan Hovold <johan@kernel.org>
Acked-by: Manivannan Sadhasivam <mani@kernel.org> # PCI_PWRCTRL
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://patch.msgid.link/20260406162231.v5.8.I806b8636cd3724f6cd1f5e199318ab8694472d90@changeid
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
Here is the set of tty and serial driver changes for 7.1-rc1.
Not much here this cycle, biggest thing is the removal of an old driver
that never got any actual hardware support (esp32), and the second try
to moving the tty ports to their own workqueues (first try was in
7.0-rc1 but was reverted due to problems.)
Otherwise it's just a small set of driver updates and some vt modifier
key enhancements.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCaeTdzg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymr3gCeKwRtlyy5LOFs/vikB47gf/aBb1MAoIv4JBDo
xWvKMVFvMD7XfsJkPHyR
=l37E
-----END PGP SIGNATURE-----
Merge tag 'tty-7.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the set of tty and serial driver changes for 7.1-rc1.
Not much here this cycle, biggest thing is the removal of an old
driver that never got any actual hardware support (esp32), and the
second try to moving the tty ports to their own workqueues (first try
was in 7.0-rc1 but was reverted due to problems)
Otherwise it's just a small set of driver updates and some vt modifier
key enhancements.
All have been in linux-next for a while with no reported issues"
* tag 'tty-7.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (35 commits)
tty: serial: ip22zilog: Fix section mispatch warning
hvc/xen: Check console connection flag
serial: sh-sci: Add support for RZ/G3L RSCI
dt-bindings: serial: renesas,rsci: Document RZ/G3L SoC
tty: atmel_serial: update outdated reference to atmel_tasklet_func()
serial: xilinx_uartps: Drop unused include
serial: qcom-geni: drop stray newline format specifier
serial: 8250: loongson: Enable building on MIPS Loongson64
dt-bindings: serial: 8250: Add Loongson 3A4000 uart compatible
serial: 8250_fintek: Add support for F81214E
tty: tty_port: add workqueue to flip TTY buffer
vt: support ITU-T T.416 color subparameters
serial: qcom-geni: Fix RTS behavior with flow control
tty: serial: imx: keep dma request disabled before dma transfer setup
tty: serial: 8250: Add SystemBase Multi I/O cards
serial: pic32_uart: allow driver to be compiled on all architectures with COMPILE_TEST
serial: tegra: remove Kconfig dependency on APB DMA controller
dt-bindings: serial: amlogic,meson-uart: Add compatible string for A9
dt-bindings: serial: atmel,at91-usart: add microchip,lan9691-usart
serial: auart: check clk_enable() return in console write
...
-----BEGIN PGP SIGNATURE-----
iJEEABYKADkWIQRTLbB6QfY48x44uB6AXGG7T9hjvgUCads37xsUgAAAAAAEAA5t
YW51MiwyLjUrMS4xMiwyLDIACgkQgFxhu0/YY75fRAEAj/0nnnnaJr3sMKccUggc
JXvkGAiskxmnEbqR2TSCr2QA/jOnI6Thp/c2DMtljRuLu2NWl89ztGYbTfKfDiwM
mAEJ
=FcRV
-----END PGP SIGNATURE-----
Merge tag 'for-linus-7.1-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen updates from Juergen Gross:
- fix an error path in drivers/xen/manage.c
- fix the Xen console driver solving a boot hangup when the console
backend isn't yet running
- comment fix in the Xen swiotlb driver
- hardening for Xen on Arm adding a more thorough validation
- cleanup of the Xen grant table code hiding suspend/resume code for
the case if CONFIG_HIBERNATE_CALLBACKS isn't defined
* tag 'for-linus-7.1-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/grant-table: guard gnttab_suspend/resume with CONFIG_HIBERNATE_CALLBACKS
hvc/xen: Check console connection flag
xen/swiotlb: fix stale reference to swiotlb_unmap_page()
xen/manage: unwind partial shutdown watcher setup on error
ARM: xen: validate hypervisor compatible before parsing its version
A major refactorization by Thomas Zimmermann from SUSE regarding handling of
console font data, addition of helpers for console font rotation and split into
individual components for glyphs, fonts and the overall fbcon state.
And there is the round of usual code cleanups and fixes:
Cleanups:
- atyfb: Remove unused fb_list [Geert Uytterhoeven]
- goldfishfb, wmt_ge_rops: use devm_platform_ioremap_resource() [Amin GATTOUT]
- matroxfb: Mark variable with __maybe_unused [Andy Shevchenko]
- omapfb: Add missing error check for clk_get() [Chen Ni]
- tdfxfb: Make the VGA register initialisation a bit more obvious [Daniel Palmer]
- macfb: Replace deprecated strcpy with strscpy [Thorsten Blum]
Fixes:
- tdfxfb, udlfb: avoid divide-by-zero on FBIOPUT_VSCREENINFO [Greg Kroah-Hartman]
- omap2: fix inconsistent lock returns in omapfb_mmap [Hongling Zeng]
- viafb: check ioremap return value in viafb_lcd_get_mobile_state [Wang Jun]
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQS86RI+GtKfB8BJu973ErUQojoPXwUCad5fnwAKCRD3ErUQojoP
X5z0AP4vBt7fGFNs4dpSTkMy/ECoM1PZEdjXRRNthFy44Hc56AD/SCVfskxBmcf1
Aa1SvKEA0s7lmMAWjQyDeQDK1QdyAQo=
=Q2+Z
-----END PGP SIGNATURE-----
Merge tag 'fbdev-for-7.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev
Pull fbdev updates from Helge Deller:
"A major refactorization by Thomas Zimmermann from SUSE regarding
handling of console font data, addition of helpers for console font
rotation and split into individual components for glyphs, fonts and
the overall fbcon state.
And there is the round of usual code cleanups and fixes:
Cleanups:
- atyfb: Remove unused fb_list (Geert Uytterhoeven)
- goldfishfb, wmt_ge_rops: use devm_platform_ioremap_resource() (Amin GATTOUT)
- matroxfb: Mark variable with __maybe_unused (Andy Shevchenko)
- omapfb: Add missing error check for clk_get() (Chen Ni)
- tdfxfb: Make the VGA register initialisation a bit more obvious (Daniel Palmer)
- macfb: Replace deprecated strcpy with strscpy (Thorsten Blum)
Fixes:
- tdfxfb, udlfb: avoid divide-by-zero on FBIOPUT_VSCREENINFO (Greg Kroah-Hartman)
- omap2: fix inconsistent lock returns in omapfb_mmap (Hongling Zeng)
- viafb: check ioremap return value in viafb_lcd_get_mobile_state (Wang Jun)"
* tag 'fbdev-for-7.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev: (40 commits)
fbdev: udlfb: avoid divide-by-zero on FBIOPUT_VSCREENINFO
fbdev: tdfxfb: avoid divide-by-zero on FBIOPUT_VSCREENINFO
fbdev: omap2: fix inconsistent lock returns in omapfb_mmap
MAINTAINERS: Add dedicated entry for fbcon
fbcon: Put font-rotation state into separate struct
fbcon: Fill cursor mask in helper function
lib/fonts: Implement font rotation
lib/fonts: Refactor glyph-rotation helpers
lib/fonts: Refactor glyph-pattern helpers
lib/fonts: Implement glyph rotation
lib/fonts: Clean up Makefile
lib/fonts: Provide helpers for calculating glyph pitch and size
vt: Implement helpers for struct vc_font in source file
fbcon: Avoid OOB font access if console rotation fails
fbdev: atyfb: Remove unused fb_list
fbdev: matroxfb: Mark variable with __maybe_unused to avoid W=1 build break
fbdev: update help text for CONFIG_FB_NVIDIA
fbdev: omapfb: Add missing error check for clk_get()
fbdev: viafb: check ioremap return value in viafb_lcd_get_mobile_state
lib/fonts: Remove internal symbols and macros from public header file
...
- add support for the PCIe M.2 Key E connectors in pwrseq-pcie-m2
- describe PCIe M.2 Mechanical Key E connectors in DT bindings
- add serdev helpers for looking up devices by OF nodes
- minor serdev core rework to enable support for PCIe M.2 Key E connectors
-----BEGIN PGP SIGNATURE-----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=Nqgg
-----END PGP SIGNATURE-----
Merge tag 'pwrseq-updates-for-v7.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull power sequencing updates from Bartosz Golaszewski:
"For this release we have an extension of the pwrseq-pcie-m2 driver
with support for PCIe M.2 Key E connectors.
The rest of the commits fulfill a supporting role: document the
hardware in DT bindings, provide required serdev helpers (this has
been provided in an immutable branch to Rob Herring so you may see it
in his PR as well) and is followed up by some Kconfig fixes from Arnd.
Summary:
- add support for the PCIe M.2 Key E connectors in pwrseq-pcie-m2
- describe PCIe M.2 Mechanical Key E connectors in DT bindings
- add serdev helpers for looking up devices by OF nodes
- minor serdev core rework to enable support for PCIe M.2 Key E
connectors"
* tag 'pwrseq-updates-for-v7.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
power: sequencing: pcie-m2: add SERIAL_DEV_BUS dependency
power: sequencing: pcie-m2: enforce PCI and OF dependencies
power: sequencing: pcie-m2: Create serdev device for WCN7850 bluetooth
power: sequencing: pcie-m2: Add support for PCIe M.2 Key E connectors
dt-bindings: connector: Add PCIe M.2 Mechanical Key E connector
dt-bindings: serial: Document the graph port
serdev: Do not return -ENODEV from of_serdev_register_devices() if external connector is used
serdev: Add an API to find the serdev controller associated with the devicetree node
serdev: Convert to_serdev_*() helpers to macros and use container_of_const()
When the console out buffer is filled, __write_console() will return 0
as it cannot send any data. domU_write_console() will then spin in
`while (len)` as len doesn't decrement until xenconsoled attaches. This
would block a domU and nullify the parallelism of Hyperlaunch until dom0
userspace starts xenconsoled, which empties the buffer.
Xen 4.21 added a connection field to the xen console page. This is set
to XENCONSOLE_DISCONNECTED (1) when a domain is built, and xenconsoled
will set it to XENCONSOLE_CONNECTED (0) when it connects.
Update the hvc_xen driver to check the field. When the field is
disconnected, drop the write with -ENOTCONN. We only drop the write
when the field is XENCONSOLE_DISCONNECTED (1) to try for maximum
compatibility. The Xen toolstack has historically zero initialized the
console, so it should see XENCONSOLE_CONNECTED (0) by default. If an
implemenation used uninitialized memory, only checking for
XENCONSOLE_DISCONNECTED could have the lowest chance of not connecting.
This lets the hyperlaunched domU boot without stalling. Once dom0
starts xenconsoled, xl console can be used to access the domU's hvc0.
Paritally sync console.h from xen.git to bring in the new field.
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Jason Andryuk <jason.andryuk@amd.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Message-ID: <20260318235326.14568-1-jason.andryuk@amd.com>
Implement pitch and size calculation for a single font glyph in the
new helpers font_glyph_pitch() and font_glyph_size(). Replace the
instances where the calculations are open-coded.
Note that in the case of fbcon console rotation, the parameters for
a glyph's width and height might be reversed. This is intentional.
v2:
- fix typos in commit message
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Helge Deller <deller@gmx.de>
Move the helpers vc_font_pitch() and vc_font_size() from the VT
header file into source file. They are not called very often, so
there's no benefit in keeping them in the headers. Also avoids
including <linux/math.h> from the header.
v2:
- fix typo in commit description
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Helge Deller <deller@gmx.de>
If an external connector like M.2 is connected to the serdev controller
in DT, then the serdev devices may be created dynamically by the connector
driver. So do not return -ENODEV from of_serdev_register_devices() if the
static nodes are not found and the graph node is used.
Tested-by: Hans de Goede <johannes.goede@oss.qualcomm.com> # ThinkPad T14s gen6 (arm64)
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@oss.qualcomm.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20260326-pci-m2-e-v7-3-43324a7866e6@oss.qualcomm.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Instead of discarding the saved unicode buffer when the console was
resized while in the alternate screen, resize it to the current
dimensions using vc_uniscr_copy_area() to preserve its content. This
properly restores the unicode screen on alt screen exit rather than
lazily rebuilding it from a lossy reverse glyph translation.
On allocation failure the stale buffer is freed and vc_uni_lines is
set to NULL so it gets lazily rebuilt via vc_uniscr_check() when next
needed.
Fixes: 40014493ce ("vt: discard stale unicode buffer on alt screen exit after resize")
Cc: stable <stable@kernel.org>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Link: https://patch.msgid.link/3nsr334n-079q-125n-7807-n4nq818758ns@syhkavp.arg
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When enter_alt_screen() saves vc_uni_lines into vc_saved_uni_lines and
sets vc_uni_lines to NULL, a subsequent console resize via vc_do_resize()
skips reallocating the unicode buffer because vc_uni_lines is NULL.
However, vc_saved_uni_lines still points to the old buffer allocated for
the original dimensions.
When leave_alt_screen() later restores vc_saved_uni_lines, the buffer
dimensions no longer match vc_rows/vc_cols. Any operation that iterates
over the unicode buffer using the current dimensions (e.g. csi_J clearing
the screen) will access memory out of bounds, causing a kernel oops:
BUG: unable to handle page fault for address: 0x0000002000000020
RIP: 0010:csi_J+0x133/0x2d0
The faulting address 0x0000002000000020 is two adjacent u32 space
characters (0x20) interpreted as a pointer, read from the row data area
past the end of the 25-entry pointer array in a buffer allocated for
80x25 but accessed with 240x67 dimensions.
Fix this by checking whether the console dimensions changed while in the
alternate screen. If they did, free the stale saved buffer instead of
restoring it. The unicode screen will be lazily rebuilt via
vc_uniscr_check() when next needed.
Fixes: 5eb608319b ("vt: save/restore unicode screen buffer for alternate screen")
Cc: stable <stable@kernel.org>
Tested-by: Liav Mordouch <liavmordouch@gmail.com>
Signed-off-by: Liav Mordouch <liavmordouch@gmail.com>
Reviewed-by: Nicolas Pitre <nico@fluxnic.net>
Link: https://patch.msgid.link/20260327170204.29706-1-liavmordouch@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the console out buffer is filled, __write_console() will return 0
as it cannot send any data. domU_write_console() will then spin in
`while (len)` as len doesn't decrement until xenconsoled attaches. This
would block a domU and nullify the parallelism of Hyperlaunch until dom0
userspace starts xenconsoled, which empties the buffer.
Xen 4.21 added a connection field to the xen console page. This is set
to XENCONSOLE_DISCONNECTED (1) when a domain is built, and xenconsoled
will set it to XENCONSOLE_CONNECTED (0) when it connects.
Update the hvc_xen driver to check the field. When the field is
disconnected, drop the write with -ENOTCONN. We only drop the write
when the field is XENCONSOLE_DISCONNECTED (1) to try for maximum
compatibility. The Xen toolstack has historically zero initialized the
console, so it should see XENCONSOLE_CONNECTED (0) by default. If an
implemenation used uninitialized memory, only checking for
XENCONSOLE_DISCONNECTED could have the lowest chance of not connecting.
This lets the hyperlaunched domU boot without stalling. Once dom0
starts xenconsoled, xl console can be used to access the domU's hvc0.
Paritally sync console.h from xen.git to bring in the new field.
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Jason Andryuk <jason.andryuk@amd.com>
Link: https://patch.msgid.link/20260318235326.14568-1-jason.andryuk@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for RZ/G3L RSCI. The RSCI IP found on the RZ/G3L SoC is
similar to RZ/G3E, but it has 3 clocks (2 module clocks + 1 external
clock) instead of 6 clocks (5 module clocks + 1 external clock) on the
RZ/G3E. Both RZ/G3L and RZ/G3E have a 32-bit FIFO, but RZ/G3L has a
single TCLK with internal dividers, whereas the RZ/G3E has explicit
clocks for TCLK and its dividers. Add a new port type
RSCI_PORT_SCIF32_SINGLE_TCLK to handle this clock difference.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260312082708.98835-3-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The modem-status comparison that used irq_status_prev was
moved from atmel_tasklet_func() into atmel_handle_status() in
commit d033e82db9 ("tty/serial: at91: handle IRQ status
more safely"). Update the comment accordingly.
Assisted-by: unnamed:deepseek-v3.2 coccinelle
Signed-off-by: Kexin Sun <kexinsun@smail.nju.edu.cn>
Link: https://patch.msgid.link/20260324024857.3244-1-kexinsun@smail.nju.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop the newline character from the middle of the printk message.
This avoids breaking the message into two lines unnecessarily.
Signed-off-by: Kathiravan Thirumoorthy <kathiravan.thirumoorthy@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://patch.msgid.link/20260319-drop_stray_n-v1-1-37fb619538bb@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Loongson 3A4000 is a MIPS-based Loongson64 CPU which also supports
8250_loongson (loongson-uart).
Enable building on MIPS Loongson64 so that Loongson 3A4000 can benefit
from it.
Signed-off-by: Rong Zhang <rongrong@oss.cipunited.com>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Link: https://patch.msgid.link/20260315184301.412844-3-rongrong@oss.cipunited.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The F81214E is a LPC/eSPI to 2 UART Super I/O chip.
Functionally, it is the same as the F81216E. The only difference
is that the F81216E has 4 UART ports, whereas the F81214E has 2
UART ports.
Signed-off-by: Ravi Rama <ravi.rama@nexthop.ai>
Link: https://patch.msgid.link/20260313194731.2671-1-ravi.rama@nexthop.ai
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCgA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmnAYjkeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGUawH/RJlc6oT7epAoDmS
STyZW2CF1U4r8YRFmB2LdmAeydMBbxiQeISN6ap3SkNGURGCZ9WcxjOE4uFhL2WW
aQMTxFaSwj9YxB6x7P9JUn/evJWFh8Fhh48kh2LfXPEpxYQBaMhnGzDSZJ3rtRxi
NMJ/OXqg8JbZS44S2OOC9HxgoYBJ1pNXvi/Q6hWFEJphr3qXaxSvl4go0zMNFEbq
39CK5vbJC8yQo4R/MAjuGvFs+Ivpjypp56iSIpK45z53Dfv255iSzIJhDxM3YGvl
p3nVKpKAPuQMXpOUMOEl6z6muRL50es/Kgi2xh2JK6FWOOOgfunGNWDG/g5mgxjI
QDUAm6U=
=2ECC
-----END PGP SIGNATURE-----
Merge 7.0-rc5 into tty-next
We need the tty/serial fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The alternate screen support added by commit 23743ba647 ("vt: add
support for smput/rmput escape codes") only saves and restores the
regular screen buffer (vc_origin), but completely ignores the corresponding
unicode screen buffer (vc_uni_lines) creating a messed-up display.
Add vc_saved_uni_lines to save the unicode screen buffer when entering
the alternate screen, and restore it when leaving. Also ensure proper
cleanup in reset_terminal() and vc_deallocate().
Fixes: 23743ba647 ("vt: add support for smput/rmput escape codes")
Cc: stable <stable@kernel.org>
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Link: https://patch.msgid.link/5o2p6qp3-91pq-0p17-or02-1oors4417ns7@onlyvoer.pbz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DW UART cannot write to LCR, DLL, and DLH while BUSY is asserted.
Existance of BUSY depends on uart_16550_compatible, if UART HW is
configured with it those registers can always be written.
There currently is dw8250_force_idle() which attempts to achieve
non-BUSY state by disabling FIFO, however, the solution is unreliable
when Rx keeps getting more and more characters.
Create a sequence of operations that ensures UART cannot keep BUSY
asserted indefinitely. The new sequence relies on enabling loopback mode
temporarily to prevent incoming Rx characters keeping UART BUSY.
Ensure no Tx in ongoing while the UART is switches into the loopback
mode (requires exporting serial8250_fifo_wait_for_lsr_thre() and adding
DMA Tx pause/resume functions).
According to tests performed by Adriana Nicolae <adriana@arista.com>,
simply disabling FIFO or clearing FIFOs only once does not always
ensure BUSY is deasserted but up to two tries may be needed. This could
be related to ongoing Rx of a character (a guess, not known for sure).
Therefore, retry FIFO clearing a few times (retry limit 4 is arbitrary
number but using, e.g., p->fifosize seems overly large). Tests
performed by others did not exhibit similar challenge but it does not
seem harmful to leave the FIFO clearing loop in place for all DW UARTs
with BUSY functionality.
Use the new dw8250_idle_enter/exit() to do divisor writes and LCR
writes. In case of plain LCR writes, opportunistically try to update
LCR first and only invoke dw8250_idle_enter() if the write did not
succeed (it has been observed that in practice most LCR writes do
succeed without complications).
This issue was first reported by qianfan Zhao who put lots of debugging
effort into understanding the solution space.
Fixes: c49436b657 ("serial: 8250_dw: Improve unwritable LCR workaround")
Fixes: 7d4008ebb1 ("tty: add a DesignWare 8250 driver")
Cc: stable <stable@kernel.org>
Reported-by: qianfan Zhao <qianfanguijin@163.com>
Link: https://lore.kernel.org/linux-serial/289bb78a-7509-1c5c-2923-a04ed3b6487d@163.com/
Reported-by: Adriana Nicolae <adriana@arista.com>
Link: https://lore.kernel.org/linux-serial/20250819182322.3451959-1-adriana@arista.com/
Reported-by: Bandal, Shankar <shankar.bandal@intel.com>
Tested-by: Bandal, Shankar <shankar.bandal@intel.com>
Tested-by: Murthy, Shanth <shanth.murthy@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://patch.msgid.link/20260203171049.4353-8-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When DW UART is !uart_16550_compatible, it can indicate BUSY at any
point (when under constant Rx pressure) unless a complex sequence of
steps is performed. Any LCR write can run a foul with the condition
that prevents writing LCR while the UART is BUSY, which triggers
BUSY_DETECT interrupt that seems unmaskable using IER bits.
Normal flow is that dw8250_handle_irq() handles BUSY_DETECT condition
by reading USR register. This BUSY feature, however, breaks the
assumptions made in serial8250_do_shutdown(), which runs
synchronize_irq() after clearing IER and assumes no interrupts can
occur after that point but then proceeds to update LCR, which on DW
UART can trigger an interrupt.
If serial8250_do_shutdown() releases the interrupt handler before the
handler has run and processed the BUSY_DETECT condition by read the USR
register, the IRQ is not deasserted resulting in interrupt storm that
triggers "irq x: nobody cared" warning leading to disabling the IRQ.
Add late synchronize_irq() into serial8250_do_shutdown() to ensure
BUSY_DETECT from DW UART is handled before port's interrupt handler is
released. Alternative would be to add DW UART specific shutdown
function but it would mostly duplicate the generic code and the extra
synchronize_irq() seems pretty harmless in serial8250_do_shutdown().
Fixes: 7d4008ebb1 ("tty: add a DesignWare 8250 driver")
Cc: stable <stable@kernel.org>
Reported-by: Bandal, Shankar <shankar.bandal@intel.com>
Tested-by: Bandal, Shankar <shankar.bandal@intel.com>
Tested-by: Murthy, Shanth <shanth.murthy@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://patch.msgid.link/20260203171049.4353-7-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
INTC10EE UART can end up into an interrupt storm where it reports
IIR_NO_INT (0x1). If the storm happens during active UART operation, it
is promptly stopped by IIR value change due to Rx or Tx events.
However, when there is no activity, either due to idle serial line or
due to specific circumstances such as during shutdown that writes
IER=0, there is nothing to stop the storm.
During shutdown the storm is particularly problematic because
serial8250_do_shutdown() calls synchronize_irq() that will hang in
waiting for the storm to finish which never happens.
This problem can also result in triggering a warning:
irq 45: nobody cared (try booting with the "irqpoll" option)
[...snip...]
handlers:
serial8250_interrupt
Disabling IRQ #45
Normal means to reset interrupt status by reading LSR, MSR, USR, or RX
register do not result in the UART deasserting the IRQ.
Add a quirk to INTC10EE UARTs to enable Tx interrupts if UART's Tx is
currently empty and inactive. Rework IIR_NO_INT to keep track of the
number of consecutive IIR_NO_INT, and on fourth one perform the quirk.
Enabling Tx interrupts should change IIR value from IIR_NO_INT to
IIR_THRI which has been observed to stop the storm.
Fixes: e92fad0249 ("serial: 8250_dw: Add ACPI ID for Granite Rapids-D UART")
Cc: stable <stable@kernel.org>
Reported-by: Bandal, Shankar <shankar.bandal@intel.com>
Tested-by: Bandal, Shankar <shankar.bandal@intel.com>
Tested-by: Murthy, Shanth <shanth.murthy@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://patch.msgid.link/20260203171049.4353-6-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dw8250_handle_irq() takes port's lock multiple times with no good
reason to release it in between and calls serial8250_handle_irq()
that also takes port's lock.
Take port's lock only once in dw8250_handle_irq() and use
serial8250_handle_irq_locked() to avoid releasing port's lock in
between.
As IIR_NO_INT check in serial8250_handle_irq() was outside of port's
lock, it has to be done already in dw8250_handle_irq().
DW UART can, in addition to IIR_NO_INT, report BUSY_DETECT (0x7) which
collided with the IIR_NO_INT (0x1) check in serial8250_handle_irq()
(because & is used instead of ==) meaning that no other work is done by
serial8250_handle_irq() during an BUSY_DETECT interrupt.
This allows reorganizing code in dw8250_handle_irq() to do both
IIR_NO_INT and BUSY_DETECT handling right at the start simplifying
the logic.
Tested-by: Bandal, Shankar <shankar.bandal@intel.com>
Tested-by: Murthy, Shanth <shanth.murthy@intel.com>
Cc: stable <stable@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://patch.msgid.link/20260203171049.4353-5-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
8250_port exports serial8250_handle_irq() to HW specific 8250 drivers.
It takes port's lock within but a HW specific 8250 driver may want to
take port's lock itself, do something, and then call the generic
handler in 8250_port but to do that, the caller has to release port's
lock for no good reason.
Introduce serial8250_handle_irq_locked() which a HW specific driver can
call while already holding port's lock.
As this is new export, put it straight into a namespace (where all 8250
exports should eventually be moved).
Tested-by: Bandal, Shankar <shankar.bandal@intel.com>
Tested-by: Murthy, Shanth <shanth.murthy@intel.com>
Cc: stable <stable@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://patch.msgid.link/20260203171049.4353-4-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When DW UART is configured with BUSY flag, LCR writes may not always
succeed which can make any LCR write complex and very expensive.
Performing write directly can trigger IRQ and the driver has to perform
complex and distruptive sequence while retrying the write.
Therefore, it's better to avoid doing LCR write that would not change
the value of the LCR register. Add LCR write avoidance code into the
8250_dw driver's .serial_out() functions.
Reported-by: Bandal, Shankar <shankar.bandal@intel.com>
Tested-by: Bandal, Shankar <shankar.bandal@intel.com>
Tested-by: Murthy, Shanth <shanth.murthy@intel.com>
Cc: stable <stable@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://patch.msgid.link/20260203171049.4353-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 8250_dw driver needs to potentially perform very complex operations
during LCR writes because its BUSY handling prevents updates to LCR
while UART is BUSY (which is not fully under our control without those
complex operations). Thus, LCR writes should occur under port's lock.
Move LCR write under port's lock in serial8250_do_shutdown(). Also
split the LCR RMW so that the logic is on a separate line for clarity.
Reported-by: Bandal, Shankar <shankar.bandal@intel.com>
Tested-by: Bandal, Shankar <shankar.bandal@intel.com>
Tested-by: Murthy, Shanth <shanth.murthy@intel.com>
Cc: stable <stable@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://patch.msgid.link/20260203171049.4353-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is found in popular brands such as StarTech.com or Delock, and has
been a source of frustration to quite a few people, if I can trust
Amazon comments complaining about Linux support via the official
out-of-the-tree driver.
Signed-off-by: Martin Roukala (né Peres) <martin.roukala@mupuf.org>
Cc: stable <stable@kernel.org>
Link: https://patch.msgid.link/20260309-8250_pci_ax99100-v1-1-3328bdfd8e94@mupuf.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_write_room() and uart_write() behave inconsistently when
xmit_buf is NULL (which happens for PORT_UNKNOWN ports that were
never properly initialized):
- uart_write_room() returns kfifo_avail() which can be > 0
- uart_write() checks xmit_buf and returns 0 if NULL
This inconsistency causes an infinite loop in drivers that rely on
tty_write_room() to determine if they can write:
while (tty_write_room(tty) > 0) {
written = tty->ops->write(...);
// written is always 0, loop never exits
}
For example, caif_serial's handle_tx() enters an infinite loop when
used with PORT_UNKNOWN serial ports, causing system hangs.
Fix by making uart_write_room() also check xmit_buf and return 0 if
it's NULL, consistent with uart_write().
Reproducer: https://gist.github.com/mrpre/d9a694cc0e19828ee3bc3b37983fde13
Signed-off-by: Jiayuan Chen <jiayuan.chen@shopee.com>
Cc: stable <stable@kernel.org>
Link: https://patch.msgid.link/20260204074327.226165-1-jiayuan.chen@linux.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ulite_probe() calls pm_runtime_put_autosuspend() at the end of probe
without holding a corresponding PM runtime reference for non-console
ports.
During ulite_assign(), uart_add_one_port() triggers uart_configure_port()
which calls ulite_pm() via uart_change_pm(). For non-console ports, the
UART core performs a balanced get/put cycle:
uart_change_pm(ON) -> ulite_pm() -> pm_runtime_get_sync() +1
uart_change_pm(OFF) -> ulite_pm() -> pm_runtime_put_autosuspend() -1
This leaves no spare reference for the pm_runtime_put_autosuspend() at
the end of probe. The PM runtime core prevents the count from actually
going below zero, and instead triggers a
"Runtime PM usage count underflow!" warning.
For console ports the bug is masked: the UART core skips the
uart_change_pm(OFF) call, so the UART core's unbalanced get happens to
pair with probe's trailing put.
Add pm_runtime_get_noresume() before pm_runtime_enable() to take an
explicit probe-owned reference that the trailing
pm_runtime_put_autosuspend() can release. This ensures a correct usage
count regardless of whether the port is a console.
Fixes: 5bbe10a694 ("tty: serial: uartlite: Add runtime pm support")
Cc: stable <stable@kernel.org>
Signed-off-by: Maciej Andrzejewski ICEYE <maciej.andrzejewski@m-works.net>
Link: https://patch.msgid.link/20260305123746.4152800-1-maciej.andrzejewski@m-works.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 039d492637 ("serial: 8250: Toggle IER bits on only after irq
has been set up") moved IRQ setup before the THRE test, in combination
with commit 205d300aea ("serial: 8250: change lock order in
serial8250_do_startup()") the interrupt handler can run during the
test and race with its IIR reads. This can produce wrong THRE test
results and cause spurious registration of the
serial8250_backup_timeout timer. Unconditionally disable the IRQ for
the short duration of the test and re-enable it afterwards to avoid
the race.
Fixes: 039d492637 ("serial: 8250: Toggle IER bits on only after irq has been set up")
Depends-on: 205d300aea ("serial: 8250: change lock order in serial8250_do_startup()")
Cc: stable <stable@kernel.org>
Signed-off-by: Peng Zhang <zhangpeng.00@bytedance.com>
Reviewed-by: Muchun Song <songmuchun@bytedance.com>
Signed-off-by: Alban Bedel <alban.bedel@lht.dlh.de>
Tested-by: Maximilian Lueer <maximilian.lueer@lht.dlh.de>
Link: https://patch.msgid.link/20260224121639.579404-1-alban.bedel@lht.dlh.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
`dmaengine_terminate_async` does not guarantee that the
`__dma_tx_complete` callback will run. The callback is currently the
only place where `dma->tx_running` gets cleared. If the transaction is
canceled and the callback never runs, then `dma->tx_running` will never
get cleared and we will never schedule new TX DMA transactions again.
This change makes it so we clear `dma->tx_running` after we terminate
the DMA transaction. This is "safe" because `serial8250_tx_dma_flush`
is holding the UART port lock. The first thing the callback does is also
grab the UART port lock, so access to `dma->tx_running` is serialized.
Fixes: 9e512eaaf8 ("serial: 8250: Fix fifo underflow on flush")
Cc: stable <stable@kernel.org>
Signed-off-by: Raul E Rangel <rrangel@google.com>
Link: https://patch.msgid.link/20260209135815.1.I16366ecb0f62f3c96fe3dd5763fcf6f3c2b4d8cd@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On the embedded platform, certain critical data, such as IMU data, is
transmitted through UART. The tty_flip_buffer_push() interface in the TTY
layer uses system_dfl_wq to handle the flipping of the TTY buffer.
Although the unbound workqueue can create new threads on demand and wake
up the kworker thread on an idle CPU, it may be preempted by real-time
tasks or other high-prio tasks.
flush_to_ldisc() needs to wake up the relevant data handle thread. When
executing __wake_up_common_lock(), it calls spin_lock_irqsave(), which
does not disable preemption but disables migration in RT-Linux. This
prevents the kworker thread from being migrated to other cores by CPU's
balancing logic, resulting in long delays. The call trace is as follows:
__wake_up_common_lock
__wake_up
ep_poll_callback
__wake_up_common
__wake_up_common_lock
__wake_up
n_tty_receive_buf_common
n_tty_receive_buf2
tty_ldisc_receive_buf
tty_port_default_receive_buf
flush_to_ldisc
In our system, the processing interval for each frame of IMU data
transmitted via UART can experience significant jitter due to this issue.
Instead of the expected 10 to 15 ms frame processing interval, we see
spikes up to 30 to 35 ms. Moreover, in just one or two hours, there can
be 2 to 3 occurrences of such high jitter, which is quite frequent. This
jitter exceeds the software's tolerable limit of 20 ms.
Introduce flip_wq in tty_port which can be set by tty_port_link_wq() or as
default linked to default workqueue allocated when tty_register_driver().
The default workqueue is allocated with flag WQ_SYSFS, so that cpumask and
nice can be set dynamically. The execution timing of tty_port_link_wq() is
not clearly restricted. The newly added function tty_port_link_driver_wq()
checks whether the flip_wq of the tty_port has already been assigned when
linking the default tty_driver's workqueue to the port. After the user has
set a custom workqueue for a certain tty_port using tty_port_link_wq(), the
system will only use this custom workqueue, even if tty_driver does not
have %TTY_DRIVER_NO_WORKQUEUE flag. When tty_port register device, flip_wq
link operation is done by tty_port_link_driver_wq(), but for in-memory
devices the link operation cannot cover all the cases. Although
tty_port_install() is dedicated for in-memory devices lik PTY to link port
allocated on demand, the logic of tty_port_install() is so simple that
people may not call it, vc_cons[0].d->port is one such case. We check the
buf.flip_wq when flip TTY buffer, if buf.flip_wq of TTY port is NULL, use
system_dfl_wq as a backup.
To avoid naming conflict of the default tty_driver's workqueue, using
'"%s-%s", driver->name, driver->driver_name' as the workqueue name. In
cases where driver_name is not specified and therefore is NULL, the
workqueue is not created. Drivers that do not define driver_name are
potentially in-memory devices like vty, which generally do not require
special workqueue settings. Even with the combination of name and
driver_name, the workqueue names can still be duplicated, as many tty
serial drivers use "ttyS" as dev_name and "serial" as driver_name. I
modified the conflicting driver_name of these drivers by appending a
suffix of _xx based on the corresponding .c file. If this modification is
not made, it could not only lead to duplicate workqueue names but also
result in duplicate entries for the /proc/tty/driver/<driver_name> nodes.
Introduce %TTY_DRIVER_NO_WORKQUEUE flag meaning not to create the
default single tty_driver workqueue. Two reasons why need to introduce the
%TTY_DRIVER_NO_WORKQUEUE flag:
1. If the WQ_SYSFS parameter is enabled, workqueue_sysfs_register() will
fail when trying to create a workqueue with the same name. The pty is an
example of this; if both CONFIG_LEGACY_PTYS and CONFIG_UNIX98_PTYS are
enabled, the call to tty_register_driver() in unix98_pty_init() will fail.
2. Different TTY ports may be used for different tasks, which may require
separate core binding control via workqueues. In this case, the workqueue
created by default in the TTY driver is unnecessary. Enabling this flag
prevents the creation of this redundant workqueue.
After applying this patch, we can set the related UART TTY flip buffer
workqueue by sysfs. We set the cpumask to CPU cores associated with the
IMU tasks, and set the nice to -20. Testing has shown significant
improvement in the previously described issue, with almost no stuttering
occurring anymore.
Tested-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Xin Zhao <jackzxcui1989@163.com>
Link: https://patch.msgid.link/20260213085039.3274704-1-jackzxcui1989@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The colon ("bit combination 03/10") is a valid character in parameter
substrings. ECMA-48 says:
Each parameter sub-string consists of one or more bit combinations
from 03/00 to 03/10; the bit combinations from 03/00 to 03/09
represent the digits ZERO to NINE; bit combination 03/10 may be used
as a separator in a parameter sub-string, for example, to separate
the fractional part of a decimal number from the integer part of
that number.
To my knowledge, the only codes where 03/10 is actually used as a
separator are the CSI-m SGR sequences. The colon separated format is
superior as an embedded string for software that doesn't wish to link
ncurses terminal database, because terminals that do not support the
requested SGR sequence can safely skip the sub-parameters rather than
misinterpret them as another sequence. Hence, some software have started
using this "modern" format [1]. We should support the colon separated
format as well.
[1] 6eabe9f2ff
Signed-off-by: Ronan Pigott <ronan@rjp.ie>
Link: https://patch.msgid.link/20260303010701.631022-1-ronan@rjp.ie
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When userspace enables flow control (CRTSCTS), the driver
deasserts RTS even when the receive buffer has space. This prevents the
peer device from transmitting, causing communication to stall.
The root cause is that the driver unconditionally uses manual RTS control
regardless of flow control mode. When CRTSCTS is set, the hardware should
automatically manage RTS based on buffer status, but the driver overrides
this by setting manual control.
Fix this by introducing port->manual_flow flag. In set_termios(), disable
manual flow when CRTSCTS is set. In set_mctrl(), only assert
SE_UART_MANUAL_RFR when manual_flow is active. Verified by enabling and
disabling hardware flow control with stty.
Signed-off-by: Anup Kulkarni <anup.kulkarni@oss.qualcomm.com>
Link: https://patch.msgid.link/20260310104155.339010-1-anup.kulkarni@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since sdma hardware configure postpone to transfer phase, have to
disable dma request before dma transfer setup because there is a
hardware limitation on sdma event enable(ENBLn) as below.
Refer SDMA 2.6.28 Channel Enable RAM (SDMAARMx_CHNENBLn) section:
"It is thus essential for the Arm platform to program them before any
DMA request is triggered to the SDMA, otherwise an unpredictable
combination of channels may be started."
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://patch.msgid.link/20260312094526.297348-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for the SystemBase Multi I/O serial cards, which are
"compatible" with a standard 16550A controllers, except that they need
to have their interrupts enabled in a proprietary way.
Tested with a Delock "Serial PCI Express x1 Card 8x Serial RS-232".
Signed-off-by: Michael Walle <mwalle@kernel.org>
Link: https://patch.msgid.link/20260225081739.946723-1-mwalle@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver currently only supports builds against a PIC32 target, or
with COMPILE_TEST on MIPS. Now that commit 24cad1a228 ("serial:
pic32_uart: update include to use pic32.h from platform_data") is
merged, it's possible to compile this driver on other architectures.
To avoid future breakage of this driver in the future, let's update the
Kconfig so that it can be built with COMPILE_TEST enabled on all
architectures.
Signed-off-by: Brian Masney <bmasney@redhat.com>
Link: https://patch.msgid.link/20260222-serial-pic32-v1-1-8fdbc0d0d334@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver runs also on SoCs without a Tegra20 APB DMA controller (e.g.
Tegra234).
Remove the Kconfig dependency on TEGRA20_APB_DMA, and remove reference to
the APB DMA controller from the Kconfig help text.
Signed-off-by: Francesco Lavra <flavra@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20260303111438.2691799-1-flavra@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a check for clk_enable() in auart_console_write(). If
clk_enable() fails, return immediately to avoid accessing
hardware registers while the clock is not enabled.
Signed-off-by: Zhaoyang Yu <2426767509@qq.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/tencent_AB29FADF1FAD67D818283B6BB4FDF66F2F08@qq.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a key is pressed with modifiers (Shift, Ctrl, Alt, etc.) and the
modifier-specific keymap has no binding (K_HOLE) or doesn't exist, fall
back to the plain keymap if the plain entry is a modifier-aware type
(KT_CUR or KT_CSI).
This allows arrow keys and CSI navigation keys to automatically handle
all modifier combinations with just a single plain map entry. The key
handlers (k_cur and k_csi) read the modifier state at runtime and encode
it into the output sequence.
For example, with just:
keycode 103 = Up
keycode 104 = Csi_Home
All these combinations now work automatically:
Up -> ESC [ A
Shift+Up -> ESC [ 1 ; 2 A
Ctrl+Up -> ESC [ 1 ; 5 A
Home -> ESC [ 1 ~
Shift+Home -> ESC [ 1 ; 2 ~
Ctrl+Home -> ESC [ 1 ; 5 ~
Previously, each modifier combination required an explicit keymap entry,
which was tedious and consumed keymap slots.
Explicit modifier bindings still take precedence - the fallback only
triggers when the modifier-specific entry is empty.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Link: https://patch.msgid.link/20260203045457.1049793-4-nico@fluxnic.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a new keysym type KT_CSI that generates CSI tilde sequences with
automatic modifier encoding. The keysym value encodes the CSI parameter
number, producing sequences like ESC [ <value> ~ or ESC [ <value> ; <mod> ~
when Shift, Alt, or Ctrl modifiers are held.
This allows navigation keys (Home, End, Insert, Delete, PgUp, PgDn) and
function keys to generate modifier-aware escape sequences without
consuming string table entries for each modifier combination.
Define key symbols for navigation keys (K_CSI_HOME, K_CSI_END, etc.)
and function keys (K_CSI_F1 through K_CSI_F20) using standard xterm
CSI parameter values.
The modifier encoding follows the xterm convention:
mod = 1 + (shift ? 1 : 0) + (alt ? 2 : 0) + (ctrl ? 4 : 0)
Allowed CSI parameter values range from 0 to 99.
Note: The Linux console historically uses a non-standard double-bracket
format for F1-F5 (ESC [ [ A through ESC [ [ E) rather than the xterm
tilde format (ESC [ 11 ~ through ESC [ 15 ~). The K_CSI_F1 through
K_CSI_F5 definitions use the xterm format. Converting F1-F5 to KT_CSI
would require updating the "linux" terminfo entry to match. Navigation
keys and F6-F20 already use the tilde format and are fully compatible.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Link: https://patch.msgid.link/20260203045457.1049793-3-nico@fluxnic.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Generate xterm-style CSI sequences with modifier parameters for arrow
keys when Shift, Alt, or Ctrl are held. For example, Shift+Up produces
ESC [ 1 ; 2 A instead of plain ESC [ A.
The modifier encoding follows the standard xterm convention:
mod = 1 + (shift ? 1 : 0) + (alt ? 2 : 0) + (ctrl ? 4 : 0)
When no modifiers are pressed, the original behavior is preserved.
Explicit keymap bindings for modified cursor keys (e.g., "shift keycode
103 = Find") take precedence over this automatic modifier encoding.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Link: https://patch.msgid.link/20260203045457.1049793-2-nico@fluxnic.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These drivers were added about 3 years ago, and depend on the
XTENSA_PLATFORM_ESP32 config option which has never existed,
so no device can actually use them.
They can only be compiled with COMPILE_TEST.
In a previous conversation [1], Greg suggested removing the
drivers, and Max, the original submitter of the drivers, agreed
due to a lack of foreseeable development.
Link: https://lore.kernel.org/all/20260308131412.1102749-1-julianbraha@gmail.com/ [1]
Signed-off-by: Julian Braha <julianbraha@gmail.com>
Link: https://patch.msgid.link/20260309122321.1528622-1-julianbraha@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some DMA controllers require transfer lengths to be aligned to a
specific boundary. For example, the Tegra GPC DMA requires 4-byte
(word) aligned transfers and will reject unaligned lengths.
Align the TX DMA buffer length down to the DMA controller's copy_align
boundary before submitting the transfer. Any remaining unaligned bytes
will be transmitted via PIO on subsequent calls, which is the existing
fallback behavior when DMA is not used.
Signed-off-by: Kartik Rajput <kkartik@nvidia.com>
Link: https://patch.msgid.link/20260225065915.341522-5-kkartik@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for the NVIDIA Tegra264 UART controller, which is derived
from the AMBA PL011 design.
On Tegra264, the fractional baud rate divisor (FBRD) register is broken.
Using IBRD alone may not achieve the required baud rate
tolerance. Enable the skip_ibrd_fbrd and set_uartclk_rate flags for
the NVIDIA variant.
Signed-off-by: Kartik Rajput <kkartik@nvidia.com>
Link: https://patch.msgid.link/20260225065915.341522-4-kkartik@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The NVIDIA Tegra264 UART relies on configuring the UART clock rate
directly to program the desired baud rate.
Introduce the set_uartclk_rate vendor flag. When set, the driver
uses clk_set_rate() to program the UART clock to the desired baud
rate and clk_round_rate() to determine the maximum supported baud
rate.
Signed-off-by: Kartik Rajput <kkartik@nvidia.com>
Link: https://patch.msgid.link/20260225065915.341522-3-kkartik@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The NVIDIA Tegra264 UART has a broken fractional baud rate
divisor register. Using IBRD and FBRD may cause the baud rate
to fall outside the required tolerance.
Introduce the skip_ibrd_fbrd vendor flag to skip IBRD/FBRD
programming. When set, the baud rate is derived directly from the
UART clock rate using a fixed divisor.
Signed-off-by: Kartik Rajput <kkartik@nvidia.com>
Link: https://patch.msgid.link/20260225065915.341522-2-kkartik@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the PL011 driver only enables the UART (by setting UARTEN
in REG_CR) in pl011_startup(), so if it is used for earlycon it is
relying on the bootrom/firmware having left the UART enabled.
There's no particular reason not to actively enable the UART before
using it for earlycon, and the earlycon handling for e.g. the 8250
UART sets up the UART in its setup function, so follow that in the
PL011.
This allows use of earlycon with a UART that the firmware hasn't
already been using for its own output, but the main motivation is
that QEMU will otherwise log a message complaining that the guest is
trying to write to a UART it never enabled.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://patch.msgid.link/20260210125100.223138-1-peter.maydell@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MAX_HVC_IUCV_LINES == HVC_ALLOC_TTY_ADAPTERS == 8.
This is the number of entries in:
static struct hvc_iucv_private *hvc_iucv_table[MAX_HVC_IUCV_LINES];
Sometimes hvc_iucv_table[] is limited by:
(a) if (num > hvc_iucv_devices) // for error detection
or
(b) for (i = 0; i < hvc_iucv_devices; i++) // in 2 places
(so these 2 don't agree; second one appears to be correct to me.)
hvc_iucv_devices can be 0..8. This is a counter.
(c) if (hvc_iucv_devices > MAX_HVC_IUCV_LINES)
If hvc_iucv_devices == 8, (a) allows the code to access hvc_iucv_table[8].
Oops.
Fixes: 44a01d5ba8 ("[S390] s390/hvc_console: z/VM IUCV hypervisor console support")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://patch.msgid.link/20260130072939.1535869-1-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial8250_release_dma() is NULL-aware, no need to check this in the caller.
While at it, make sure DMA won't be used again, by NULLifying the pointer.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://patch.msgid.link/20260128142726.128175-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a05025d0ce ("tty: serial: samsung_tty: use standard
debugging macros") changed the debug prints to dev_dbg, which can
result in deadlocks:
s3c24xx_serial_set_termios can be called with the port lock, and then
calls dev_dbg, which needs the console mutex. At the same time,
s3c24xx_serial_console_write can be called with the console lock
(e.g., inside console_unlock), and needs the port lock.
To avoid this, move one dev_dbg call and just delete the other.
Signed-off-by: Alyssa Milburn <amilburn@zall.org>
Link: https://patch.msgid.link/aXny9km6N1v9eoXU@zall.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts some of the visually simpler cases that have been split
over multiple lines. I only did the ones that are easy to verify the
resulting diff by having just that final GFP_KERNEL argument on the next
line.
Somebody should probably do a proper coccinelle script for this, but for
me the trivial script actually resulted in an assertion failure in the
middle of the script. I probably had made it a bit _too_ trivial.
So after fighting that far a while I decided to just do some of the
syntactically simpler cases with variations of the previous 'sed'
scripts.
The more syntactically complex multi-line cases would mostly really want
whitespace cleanup anyway.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the exact same thing as the 'alloc_obj()' version, only much
smaller because there are a lot fewer users of the *alloc_flex()
interface.
As with alloc_obj() version, this was done entirely with mindless brute
force, using the same script, except using 'flex' in the pattern rather
than 'objs*'.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This was done entirely with mindless brute force, using
git grep -l '\<k[vmz]*alloc_objs*(.*, GFP_KERNEL)' |
xargs sed -i 's/\(alloc_objs*(.*\), GFP_KERNEL)/\1)/'
to convert the new alloc_obj() users that had a simple GFP_KERNEL
argument to just drop that argument.
Note that due to the extreme simplicity of the scripting, any slightly
more complex cases spread over multiple lines would not be triggered:
they definitely exist, but this covers the vast bulk of the cases, and
the resulting diff is also then easier to check automatically.
For the same reason the 'flex' versions will be done as a separate
conversion.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the result of running the Coccinelle script from
scripts/coccinelle/api/kmalloc_objs.cocci. The script is designed to
avoid scalar types (which need careful case-by-case checking), and
instead replace kmalloc-family calls that allocate struct or union
object instances:
Single allocations: kmalloc(sizeof(TYPE), ...)
are replaced with: kmalloc_obj(TYPE, ...)
Array allocations: kmalloc_array(COUNT, sizeof(TYPE), ...)
are replaced with: kmalloc_objs(TYPE, COUNT, ...)
Flex array allocations: kmalloc(struct_size(PTR, FAM, COUNT), ...)
are replaced with: kmalloc_flex(*PTR, FAM, COUNT, ...)
(where TYPE may also be *VAR)
The resulting allocations no longer return "void *", instead returning
"TYPE *".
Signed-off-by: Kees Cook <kees@kernel.org>
Here is the small amount of tty and serial driver updates for 7.0-rc1.
Nothing major in here at all, just some driver updates and minor tweaks
and cleanups including:
- sh-sci serial driver updates
- 8250 driver updates
- attempt to make the tty ports have their own workqueue, but was
reverted after testing found it to have problems on some platforms.
This will probably come back for 7.1 after it has been reworked and
resubmitted
- other tiny tty driver changes
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCaZR1VQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykfsACghiyMgr0XKVDFEpV7/fPzocKH+o0An3v8knSi
kLz/f6LstVsISqCxeT+9
=uozB
-----END PGP SIGNATURE-----
Merge tag 'tty-7.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver updates from Greg KH:
"Here is the small amount of tty and serial driver updates for 7.0-rc1.
Nothing major in here at all, just some driver updates and minor
tweaks and cleanups including:
- sh-sci serial driver updates
- 8250 driver updates
- attempt to make the tty ports have their own workqueue, but was
reverted after testing found it to have problems on some platforms.
This will probably come back for 7.1 after it has been reworked and
resubmitted
- other tiny tty driver changes
All of these have been in linux-next for a while with no reported
problems"
* tag 'tty-7.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (49 commits)
Revert "tty: tty_port: add workqueue to flip TTY buffer"
tty: tty_port: add workqueue to flip TTY buffer
serial: 8250_pci: Remove custom deprecated baud setting routine
serial: 8250_omap: Remove custom deprecated baud setting routine
dt-bindings: serial: renesas,scif: Document RZ/G3L SoC
serial: 8250: omap: set out-of-band wakeup if wakeup pinctrl exists
tty: hvc-iucv: Remove KMSG_COMPONENT macro
dt-bindings: serial: google,goldfish-tty: Convert to DT schema
dt-bindings: serial: sh-sci: Fold single-entry compatibles into enum
serial: 8250: 8250_omap.c: Clear DMA RX running status only after DMA termination is done
serial: 8250: 8250_omap.c: Add support for handling UART error conditions
serial: SH_SCI: improve "DMA support" prompt
serial: Kconfig: fix ordering of entries for menu display
serial: 8250: fix ordering of entries for menu display
serial: imx: change SERIAL_IMX_CONSOLE to bool
8250_men_mcb: drop unneeded MODULE_ALIAS
serial: men_z135_uart: drop unneeded MODULE_ALIAS
dt-bindings: serial: renesas,rsci: Document RZ/V2H(P) and RZ/V2N SoCs
serial: rsci: Convert to FIELD_MODIFY()
dt-bindings: serial: 8250: add SpacemiT K3 UART compatible
...
-----BEGIN PGP SIGNATURE-----
iQJOBAABCAA4FiEEbt46xwy6kEcDOXoUeZbBVTGwZHAFAmmS5oAaHHRzYm9nZW5k
QGFscGhhLmZyYW5rZW4uZGUACgkQeZbBVTGwZHD+LQ//fuj3BDTImgyHTBlj8yDC
XF4zl5xv7ivMgTTnW9PiJdKXZOvyzGZ3Tiu4ZUdOhvpSZHtcSzJISdQC+fbTMPF6
dN7SXnF27rRzjp2nV1nhhvOWMqY53hgQiVv17qJhCwb4/nyh/69ckQu0Ut4wagn4
n/+ebRq7kIgQtzrQLnw/3oX2mcAuCQ+sPm2SRib2PbTxvQu4WqMwY8rfAtUss8dg
jiXs5XgH9fHpYvPDscJ95HVfZIRqvXyLx5x8QsEvBsdS2DIv2Qy/xCzNPB/HPp9d
AzRZMexSPHmC/nU7DqC4iw7FnK0//rUeUmTMjrb7+xW4P1/qTmf9LYJc5DR5N7my
FJBpqLdhu8A56nGnzP5v7DdU7lffHFBzKC4AQ96re3yqZAHhyc2humDc3/0hBbPA
DuD907llNsFlgQrD2DDg3F0ha9rEhkqhfP2QrZAXG90puoo/oRqfVF8QOF7Y2sal
7NJIZkh3DLsVaokiOKYLFdjcMED+3/VJB0b3JE0omrLjqZG8f1kVLVISawyv/jDz
NYgg3uDQ7oGJLNnKi+gCiAL4ZFZHwj3A4rJYlMIB7Q1XR+cx4cKpmiwYtwoWIv9r
AxDR6yvi8mrZ2xx4vleyeqmoB6xrHjdUJfKVXQ1kCgg7tZJWRplxQAl4HHh+cU4F
EYIoq92L+PrXrq7RNILYd0o=
=ZT9I
-----END PGP SIGNATURE-----
Merge tag 'mips_7.0' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Thomas Bogendoerfer:
"Cleanups and fixes"
* tag 'mips_7.0' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (28 commits)
Revert "clk: microchip: core: allow driver to be compiled with COMPILE_TEST"
Revert "clk: microchip: fix typo in reference to a config option"
MIPS: Implement ARCH_HAS_CC_CAN_LINK
MIPS: rb532: Fix MMIO UART resource registration
MIPS: Work around LLVM bug when gp is used as global register variable
MIPS: Loongson64: env: Fixup serial clock-frequency when using LEFI
MIPS: Loongson2ef: Use pcibios_align_resource() to block io range
MIPS: Loongson2ef: Register PCI controller in early stage
clk: microchip: fix typo in reference to a config option
MIPS: Loongson64: dts: fix phy-related definition of LS7A GMAC
clk: microchip: core: allow driver to be compiled with COMPILE_TEST
MIPS: drop unused pic32.h header
watchdog: pic32-wdt: update include to use pic32.h from platform_data
watchdog: pic32-dmt: update include to use pic32.h from platform_data
serial: pic32_uart: update include to use pic32.h from platform_data
rtc: pic32: update include to use pic32.h from platform_data
pinctrl: pic32: update include to use pic32.h from platform_data
mmc: sdhci-pic32: update include to use pic32.h from platform_data
irqchip/irq-pic32-evic: update include to use pic32.h from platform_data
clk: microchip: core: update include to use pic32.h from platform_data
...
do_con_write(), fbcon_redraw.*() invoke console_conditional_schedule()
which is a conditional scheduling point based on printk's internal
variables console_may_schedule. It may only be used if the console lock
is acquired for instance via console_lock() or console_trylock().
Prinkt sets the internal variable to 1 (and allows to schedule)
if the console lock has been acquired via console_lock(). The trylock
does not allow it.
The console_conditional_schedule() invocation in do_con_write() is
invoked shortly before console_unlock().
The console_conditional_schedule() invocation in fbcon_redraw.*()
original from fbcon_scroll() / vt's con_scroll() which originate from a
line feed.
In console_unlock() the variable is set to 0 (forbids to schedule) and
it tries to schedule while making progress printing. This is brand new
compared to when console_conditional_schedule() was added in v2.4.9.11.
In v2.6.38-rc3, console_unlock() (started its existence) iterated over
all consoles and flushed them with disabled interrupts. A scheduling
attempt here was not possible, it relied that a long print scheduled
before console_unlock().
Since commit 8d91f8b153 ("printk: do cond_resched() between lines
while outputting to consoles"), which appeared in v4.5-rc1,
console_unlock() attempts to schedule if it was allowed to schedule
while during console_lock(). Each record is idealy one line so after
every line feed.
This console_conditional_schedule() is also only relevant on
PREEMPT_NONE and PREEMPT_VOLUNTARY builds. In other configurations
cond_resched() becomes a nop and has no impact.
I'm bringing this all up just proof that it is not required anymore. It
becomes a problem on a PREEMPT_RT build with debug code enabled because
that might_sleep() in cond_resched() remains and triggers a warnings.
This is due to
legacy_kthread_func-> console_flush_one_record -> vt_console_print-> lf
-> con_scroll -> fbcon_scroll
and vt_console_print() acquires a spinlock_t which does not allow a
voluntary schedule. There is no need to fb_scroll() to schedule since
console_flush_one_record() attempts to schedule after each line.
!PREEMPT_RT is not affected because the legacy printing thread is only
enabled on PREEMPT_RT builds.
Therefore I suggest to remove console_conditional_schedule().
Cc: Simona Vetter <simona@ffwll.ch>
Cc: Helge Deller <deller@gmx.de>
Cc: linux-fbdev@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Fixes: 5f53ca3ff8 ("printk: Implement legacy printer kthread for PREEMPT_RT")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Petr Mladek <pmladek@suse.com> # from printk() POV
Signed-off-by: Helge Deller <deller@gmx.de>
Total patches: 107
Reviews/patch: 1.07
Reviewed rate: 67%
- The 2 patch series "ocfs2: give ocfs2 the ability to reclaim
suballocator free bg" from Heming Zhao saves disk space by teaching
ocfs2 to reclaim suballocator block group space.
- The 4 patch series "Add ARRAY_END(), and use it to fix off-by-one
bugs" from Alejandro Colomar adds the ARRAY_END() macro and uses it in
various places.
- The 2 patch series "vmcoreinfo: support VMCOREINFO_BYTES larger than
PAGE_SIZE" from Pnina Feder makes the vmcore code future-safe, if
VMCOREINFO_BYTES ever exceeds the page size.
- The 7 patch series "kallsyms: Prevent invalid access when showing
module buildid" from Petr Mladek cleans up kallsyms code related to
module buildid and fixes an invalid access crash when printing
backtraces.
- The 3 patch series "Address page fault in
ima_restore_measurement_list()" from Harshit Mogalapalli fixes a
kexec-related crash that can occur when booting the second-stage kernel
on x86.
- The 6 patch series "kho: ABI headers and Documentation updates" from
Mike Rapoport updates the kexec handover ABI documentation.
- The 4 patch series "Align atomic storage" from Finn Thain adds the
__aligned attribute to atomic_t and atomic64_t definitions to get
natural alignment of both types on csky, m68k, microblaze, nios2,
openrisc and sh.
- The 2 patch series "kho: clean up page initialization logic" from
Pratyush Yadav simplifies the page initialization logic in
kho_restore_page().
- The 6 patch series "Unload linux/kernel.h" from Yury Norov moves
several things out of kernel.h and into more appropriate places.
- The 7 patch series "don't abuse task_struct.group_leader" from Oleg
Nesterov removes the usage of ->group_leader when it is "obviously
unnecessary".
- The 5 patch series "list private v2 & luo flb" from Pasha Tatashin
adds some infrastructure improvements to the live update orchestrator.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCaY4giAAKCRDdBJ7gKXxA
jgusAQDnKkP8UWTqXPC1jI+OrDJGU5ciAx8lzLeBVqMKzoYk9AD/TlhT2Nlx+Ef6
0HCUHUD0FMvAw/7/Dfc6ZKxwBEIxyww=
=mmsH
-----END PGP SIGNATURE-----
Merge tag 'mm-nonmm-stable-2026-02-12-10-48' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull non-MM updates from Andrew Morton:
- "ocfs2: give ocfs2 the ability to reclaim suballocator free bg" saves
disk space by teaching ocfs2 to reclaim suballocator block group
space (Heming Zhao)
- "Add ARRAY_END(), and use it to fix off-by-one bugs" adds the
ARRAY_END() macro and uses it in various places (Alejandro Colomar)
- "vmcoreinfo: support VMCOREINFO_BYTES larger than PAGE_SIZE" makes
the vmcore code future-safe, if VMCOREINFO_BYTES ever exceeds the
page size (Pnina Feder)
- "kallsyms: Prevent invalid access when showing module buildid" cleans
up kallsyms code related to module buildid and fixes an invalid
access crash when printing backtraces (Petr Mladek)
- "Address page fault in ima_restore_measurement_list()" fixes a
kexec-related crash that can occur when booting the second-stage
kernel on x86 (Harshit Mogalapalli)
- "kho: ABI headers and Documentation updates" updates the kexec
handover ABI documentation (Mike Rapoport)
- "Align atomic storage" adds the __aligned attribute to atomic_t and
atomic64_t definitions to get natural alignment of both types on
csky, m68k, microblaze, nios2, openrisc and sh (Finn Thain)
- "kho: clean up page initialization logic" simplifies the page
initialization logic in kho_restore_page() (Pratyush Yadav)
- "Unload linux/kernel.h" moves several things out of kernel.h and into
more appropriate places (Yury Norov)
- "don't abuse task_struct.group_leader" removes the usage of
->group_leader when it is "obviously unnecessary" (Oleg Nesterov)
- "list private v2 & luo flb" adds some infrastructure improvements to
the live update orchestrator (Pasha Tatashin)
* tag 'mm-nonmm-stable-2026-02-12-10-48' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (107 commits)
watchdog/hardlockup: simplify perf event probe and remove per-cpu dependency
procfs: fix missing RCU protection when reading real_parent in do_task_stat()
watchdog/softlockup: fix sample ring index wrap in need_counting_irqs()
kcsan, compiler_types: avoid duplicate type issues in BPF Type Format
kho: fix doc for kho_restore_pages()
tests/liveupdate: add in-kernel liveupdate test
liveupdate: luo_flb: introduce File-Lifecycle-Bound global state
liveupdate: luo_file: Use private list
list: add kunit test for private list primitives
list: add primitives for private list manipulations
delayacct: fix uapi timespec64 definition
panic: add panic_force_cpu= parameter to redirect panic to a specific CPU
netclassid: use thread_group_leader(p) in update_classid_task()
RDMA/umem: don't abuse current->group_leader
drm/pan*: don't abuse current->group_leader
drm/amd: kill the outdated "Only the pthreads threading model is supported" checks
drm/amdgpu: don't abuse current->group_leader
android/binder: use same_thread_group(proc->tsk, current) in binder_mmap()
android/binder: don't abuse current->group_leader
kho: skip memoryless NUMA nodes when reserving scratch areas
...
core:
- drop kgdb support
- replace system workqueue with percpu
- account for property blobs in memcg
- MAINTAINERS updates for xe + buddy
rust:
- Fix documentation for Registration constructors.
- Use pin_init::zeroed() for fops initialization.
- Annotate DRM helpers with __rust_helper.
- Improve safety documentation for gem::Object::new().
- Update AlwaysRefCounted imports.
- mm: Prevent integer overflow in page_align().
atomic:
- add drm_device pointer to drm_private_obj
- introduce gamma/degamma LUT size check
buddy:
- fix free_trees memory leak
- prevent BUG_ON
bridge:
- introduce drm_bridge_unplug/enter/exit
- add connector argument to .hpd_notify
- lots of recounting conversions
- convert rockchip inno hdmi to bridge
- lontium-lt9611uxc: switch to HDMI audio helpers
- dw-hdmi-qp: add support for HPD-less setups
- Algoltek AG6311 support
panels:
- edp: CSW MNE007QB3-1, AUO B140HAN06.4, AUO B140QAX01.H
- st75751: add SPI support
- Sitronix ST7920, Samsung LTL106HL02
- LG LH546WF1-ED01, HannStar HSD156J
- BOE NV130WUM-T08
- Innolux G150XGE-L05
- Anbernic RG-DS
dma-buf:
- improve sg_table debugging
- add tracepoints
- call clear_page instead of memset
- start to introduce cgroup memory accounting in heaps
- remove sysfs stats
dma-fence:
- add new helpers
dp:
- mst: avoid oob access with vcpi=0
hdmi:
- limit infoframes exposure to userspace
gem:
- reduce page table overhead with THP
- fix leak in drm_gem_get_unmapped_area
gpuvm:
- API sanitation for rust bindings
sched:
- introduce new helpers
panic:
- report invalid panic modes
- add kunit tests
i915/xe display:
- Expose sharpness only if num_scalers is >= 2
- Add initial Xe3P_LPD for NVL
- BMG FBC support
- Add MTL+ platforms to support dpll framework
_ fix DIMM_S DRM decoding on ICL
- Return to using AUX interrupts
- PSR/Panel replay refactoring
- use consolidation HDMI tables
- Xe3_LPD CD2X dividier changes
xe:
- vfio: add vfio_pci for intel GPU
- multi queue support
- dynamic pagemaps and multi-device SVM
- expose temp attribs in hwmon
- NO_COMPRESSION bo flag
- expose MERT OA unit
- sysfs survivability refactor
- SRIOV PF: add MERT support
- enable SR-IOV VF migration
- Enable I2C/NVM on Crescent Island
- Xe3p page reclaimation support
- introduce SRIOV scheduler groups
- add SoC remappt support in system controller
- insert compiler barriers in GuC code
- define NVL GuC firmware
- handle GT resume failure
- fix drm scheduler layering violations
- enable GSC loading and PXP for PTL
- disable GuC Power DCC strategy on PTL
- unregister drm device on probe error
i915:
- move to kernel standard fault injection
- bump recommended GuC version for DG2 and MTL
amdgpu:
- SMUIO 15.x, PSP 15.x support
- IH 6.1.1/7.1 support
- MMHUB 3.4/4.2 support
- GC 11.5.4/12.1 support
- SDMA 6.1.4/7.1/7.11.4 support
- JPEG 5.3 support
- UserQ updates
- GC 9 gfx queue reset support
- TTM memory ops parallelization
- convert legacy logging to new helpers
- DC analog fixes
amdkfd:
- GC 11.5.4/12.1 suppport
- SDMA 6.1.4/7.1 support
- per context support
- increase kfd process hash table
- Reserved SDMA rework
radeon:
- convert legacy logging to new helpers
- use devm for i2c adapters
msm:
- GPU
- Document a612/RGMU dt bindings
- UBWC 6.0 support (for A840 / Kaanapali)
- a225 support
- DPU:
- Switched to use virtual planes by default
- Fixed DSI CMD panels on DPU 3.x
- Rewrote format handling to remove intermediate representation
- Fixed watchdog on DPU 8.x+
- Fixed TE / Vsync source setting on DPU 8.x+
- Added 3D_Mux on SC7280
- Kaanapali platform support
- Fixed UBWC register programming
- Made RM reserve DSPP-enabled mixers for CRTCs with LMs.
- Gamma correction support
- DP:
- Enabled support for eDP 1.4+ link rate tables
- Fixed MDSS1 DP indices on SA8775P, making them to work
- Fixed msm_dp_ctrl_config_msa() to work with LLVM 20
- DSI:
- Documented QCS8300 as compatible with SA8775P
- Kaanapali platform support
- DSI PHY:
- switched to divider_determine_rate()
- MDP5:
- Dropped support for MSM8998, SDM660 and SDM630 (switched over
to DPU)
- MDSS:
- Kaanapali platform support
- Fixed UBWC register programming
nova-core:
- Prepare for Turing support. This includes parsing and handling
Turing-specific firmware headers and sections as well as a Turing
Falcon HAL implementation.
- Get rid of the Result<impl PinInit<T, E>> anti-pattern.
- Relocate initializer-specific code into the appropriate initializer.
- Use CStr::from_bytes_until_nul() to remove custom helpers.
- Improve handling of unexpected firmware values.
- Clean up redundant debug prints.
- Replace c_str!() with native Rust C-string literals.
- Update nova-core task list.
nova:
- Align GEM object size to system page size.
tyr:
- Use generated uAPI bindings for GpuInfo.
- Replace manual sleeps with read_poll_timeout().
- Replace c_str!() with native Rust C-string literals.
- Suppress warnings for unread fields.
- Fix incorrect register name in print statement.
nouveau:
- fix big page table support races in PTE management
- improve reclocking on tegra 186+
amdxdna:
- fix suspend race conditions
- improve handling of zero tail pointers
- fix cu_idx overwritten during command setup
- enable hardware context priority
- remove NPU2 support
- update message buffer allocation requirements
- update firmware version check
ast:
- support imported cursor buffers
- big endian fixes
etnaviv:
- add PPU flop reset support
imagination:
- add AM62P support
- introduce hw version checks
ivpu:
- implement warm boot flow
panfrost:
- add bo sync ioctl
- add GPU_PM_RT support for RZ/G3E SoC
panthor:
- add bo sync ioctl
- enable timestamp propagation
- scheduler robustness improvements
- VM termination fixes
- huge page support
rockchip:
- RK3368 HDMI Support
- get rid of atomic_check fixups
- RK3506 support
- RK3576/RK3588 improved HPD handling
rz-du:
- RZ/V2H(P) MIPI-DSI Support
v3d:
- fix DMA segment size
- convert to new logging helpers
mediatek:
- move DP training to hotplug thread
- convert logging to new helpers
- add support for HS speed DSI
- Genio 510/700/1200-EVK, Radxa NIO-12L HDMI support
atmel-hlcdc:
- switch to drmm resource
- support nomodeset
- use newer helpers
hisilicon:
- fix various DP bugs
renesas:
- fix kernel panic on reboot
exynos:
- fix vidi_connection_ioctl using wrong device
- fix vidi_connection deref user ptr
- fix concurrency regression with vidi_context
vkms:
- add configfs support for display configuration
-----BEGIN PGP SIGNATURE-----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=RFJ2
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2026-02-11' of https://gitlab.freedesktop.org/drm/kernel
Pull drm updates from Dave Airlie:
"Highlights:
- amdgpu support for lots of new IP blocks which means newer GPUs
- xe has a lot of SR-IOV and SVM improvements
- lots of intel display refactoring across i915/xe
- msm has more support for gen8 platforms
- Given up on kgdb/kms integration, it's too hard on modern hw
core:
- drop kgdb support
- replace system workqueue with percpu
- account for property blobs in memcg
- MAINTAINERS updates for xe + buddy
rust:
- Fix documentation for Registration constructors
- Use pin_init::zeroed() for fops initialization
- Annotate DRM helpers with __rust_helper
- Improve safety documentation for gem::Object::new()
- Update AlwaysRefCounted imports
- mm: Prevent integer overflow in page_align()
atomic:
- add drm_device pointer to drm_private_obj
- introduce gamma/degamma LUT size check
buddy:
- fix free_trees memory leak
- prevent BUG_ON
bridge:
- introduce drm_bridge_unplug/enter/exit
- add connector argument to .hpd_notify
- lots of recounting conversions
- convert rockchip inno hdmi to bridge
- lontium-lt9611uxc: switch to HDMI audio helpers
- dw-hdmi-qp: add support for HPD-less setups
- Algoltek AG6311 support
panels:
- edp: CSW MNE007QB3-1, AUO B140HAN06.4, AUO B140QAX01.H
- st75751: add SPI support
- Sitronix ST7920, Samsung LTL106HL02
- LG LH546WF1-ED01, HannStar HSD156J
- BOE NV130WUM-T08
- Innolux G150XGE-L05
- Anbernic RG-DS
dma-buf:
- improve sg_table debugging
- add tracepoints
- call clear_page instead of memset
- start to introduce cgroup memory accounting in heaps
- remove sysfs stats
dma-fence:
- add new helpers
dp:
- mst: avoid oob access with vcpi=0
hdmi:
- limit infoframes exposure to userspace
gem:
- reduce page table overhead with THP
- fix leak in drm_gem_get_unmapped_area
gpuvm:
- API sanitation for rust bindings
sched:
- introduce new helpers
panic:
- report invalid panic modes
- add kunit tests
i915/xe display:
- Expose sharpness only if num_scalers is >= 2
- Add initial Xe3P_LPD for NVL
- BMG FBC support
- Add MTL+ platforms to support dpll framework
_ fix DIMM_S DRM decoding on ICL
- Return to using AUX interrupts
- PSR/Panel replay refactoring
- use consolidation HDMI tables
- Xe3_LPD CD2X dividier changes
xe:
- vfio: add vfio_pci for intel GPU
- multi queue support
- dynamic pagemaps and multi-device SVM
- expose temp attribs in hwmon
- NO_COMPRESSION bo flag
- expose MERT OA unit
- sysfs survivability refactor
- SRIOV PF: add MERT support
- enable SR-IOV VF migration
- Enable I2C/NVM on Crescent Island
- Xe3p page reclaimation support
- introduce SRIOV scheduler groups
- add SoC remappt support in system controller
- insert compiler barriers in GuC code
- define NVL GuC firmware
- handle GT resume failure
- fix drm scheduler layering violations
- enable GSC loading and PXP for PTL
- disable GuC Power DCC strategy on PTL
- unregister drm device on probe error
i915:
- move to kernel standard fault injection
- bump recommended GuC version for DG2 and MTL
amdgpu:
- SMUIO 15.x, PSP 15.x support
- IH 6.1.1/7.1 support
- MMHUB 3.4/4.2 support
- GC 11.5.4/12.1 support
- SDMA 6.1.4/7.1/7.11.4 support
- JPEG 5.3 support
- UserQ updates
- GC 9 gfx queue reset support
- TTM memory ops parallelization
- convert legacy logging to new helpers
- DC analog fixes
amdkfd:
- GC 11.5.4/12.1 suppport
- SDMA 6.1.4/7.1 support
- per context support
- increase kfd process hash table
- Reserved SDMA rework
radeon:
- convert legacy logging to new helpers
- use devm for i2c adapters
msm:
- GPU
- Document a612/RGMU dt bindings
- UBWC 6.0 support (for A840 / Kaanapali)
- a225 support
- DPU:
- Switch to use virtual planes by default
- Fix DSI CMD panels on DPU 3.x
- Rewrite format handling to remove intermediate representation
- Fix watchdog on DPU 8.x+
- Fix TE / Vsync source setting on DPU 8.x+
- Add 3D_Mux on SC7280
- Kaanapali platform support
- Fix UBWC register programming
- Make RM reserve DSPP-enabled mixers for CRTCs with LMs
- Gamma correction support
- DP:
- Enable support for eDP 1.4+ link rate tables
- Fix MDSS1 DP indices on SA8775P, making them to work
- Fix msm_dp_ctrl_config_msa() to work with LLVM 20
- DSI:
- Document QCS8300 as compatible with SA8775P
- Kaanapali platform support
- DSI PHY:
- switch to divider_determine_rate()
- MDP5:
- Drop support for MSM8998, SDM660 and SDM630 (switch over to DPU)
- MDSS:
- Kaanapali platform support
- Fixed UBWC register programming
nova-core:
- Prepare for Turing support. This includes parsing and handling
Turing-specific firmware headers and sections as well as a Turing
Falcon HAL implementation
- Get rid of the Result<impl PinInit<T, E>> anti-pattern
- Relocate initializer-specific code into the appropriate initializer
- Use CStr::from_bytes_until_nul() to remove custom helpers
- Improve handling of unexpected firmware values
- Clean up redundant debug prints
- Replace c_str!() with native Rust C-string literals
- Update nova-core task list
nova:
- Align GEM object size to system page size
tyr:
- Use generated uAPI bindings for GpuInfo
- Replace manual sleeps with read_poll_timeout()
- Replace c_str!() with native Rust C-string literals
- Suppress warnings for unread fields
- Fix incorrect register name in print statement
nouveau:
- fix big page table support races in PTE management
- improve reclocking on tegra 186+
amdxdna:
- fix suspend race conditions
- improve handling of zero tail pointers
- fix cu_idx overwritten during command setup
- enable hardware context priority
- remove NPU2 support
- update message buffer allocation requirements
- update firmware version check
ast:
- support imported cursor buffers
- big endian fixes
etnaviv:
- add PPU flop reset support
imagination:
- add AM62P support
- introduce hw version checks
ivpu:
- implement warm boot flow
panfrost:
- add bo sync ioctl
- add GPU_PM_RT support for RZ/G3E SoC
panthor:
- add bo sync ioctl
- enable timestamp propagation
- scheduler robustness improvements
- VM termination fixes
- huge page support
rockchip:
- RK3368 HDMI Support
- get rid of atomic_check fixups
- RK3506 support
- RK3576/RK3588 improved HPD handling
rz-du:
- RZ/V2H(P) MIPI-DSI Support
v3d:
- fix DMA segment size
- convert to new logging helpers
mediatek:
- move DP training to hotplug thread
- convert logging to new helpers
- add support for HS speed DSI
- Genio 510/700/1200-EVK, Radxa NIO-12L HDMI support
atmel-hlcdc:
- switch to drmm resource
- support nomodeset
- use newer helpers
hisilicon:
- fix various DP bugs
renesas:
- fix kernel panic on reboot
exynos:
- fix vidi_connection_ioctl using wrong device
- fix vidi_connection deref user ptr
- fix concurrency regression with vidi_context
vkms:
- add configfs support for display configuration
* tag 'drm-next-2026-02-11' of https://gitlab.freedesktop.org/drm/kernel: (1610 commits)
drm/xe/pm: Disable D3Cold for BMG only on specific platforms
drm/xe: Fix kerneldoc for xe_tlb_inval_job_alloc_dep
drm/xe: Fix kerneldoc for xe_gt_tlb_inval_init_early
drm/xe: Fix kerneldoc for xe_migrate_exec_queue
drm/xe/query: Fix topology query pointer advance
drm/xe/guc: Fix kernel-doc warning in GuC scheduler ABI header
drm/xe/guc: Fix CFI violation in debugfs access.
accel/amdxdna: Move RPM resume into job run function
accel/amdxdna: Fix incorrect DPM level after suspend/resume
nouveau/vmm: start tracking if the LPT PTE is valid. (v6)
nouveau/vmm: increase size of vmm pte tracker struct to u32 (v2)
nouveau/vmm: rewrite pte tracker using a struct and bitfields.
accel/amdxdna: Fix incorrect error code returned for failed chain command
accel/amdxdna: Remove hardware context status
drm/bridge: imx8qxp-pixel-combiner: Fix bailout for imx8qxp_pc_bridge_probe()
drm/panel: ilitek-ili9882t: Remove duplicate initializers in tianma_il79900a_dsc
drm/i915/display: fix the pixel normalization handling for xe3p_lpd
drm/exynos: vidi: use ctx->lock to protect struct vidi_context member variables related to memory alloc/free
drm/exynos: vidi: fix to avoid directly dereferencing user pointer
drm/exynos: vidi: use priv->vidi_dev for ctx lookup in vidi_connection_ioctl()
...
-----BEGIN PGP SIGNATURE-----
iJEEABYKADkWIQRTLbB6QfY48x44uB6AXGG7T9hjvgUCaYmAPhsUgAAAAAAEAA5t
YW51MiwyLjUrMS4xMSwyLDIACgkQgFxhu0/YY75PKAEAgNaon3unLoRnCGPjkRxL
kruzd/KHcodevfz0koL7hOUA/iHOEpGIibCHJpmj2xt/kgLCxxMCQVupalDfeKwq
4jYN
=Vy9z
-----END PGP SIGNATURE-----
Merge tag 'for-linus-7.0-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen updates from Juergen Gross:
- fix running as Xen PVH guest in 32-bit mode without PAE
- fix PV device handling for suspend/resume when running as
a Xen guest
- clean up workqueue usage
- fix the Xen balloon driver for PVH dom0
- introduce the possibility to use hypercalls for console
messages in unprivileged guests
- enable Xen dom0 use of virtio devices in nested virtualization
setups
- simplify the xen-mcelog driver
* tag 'for-linus-7.0-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xenbus: Rename helpers to freeze/thaw/restore
xenbus: Use .freeze/.thaw to handle xenbus devices
xen/mcelog: simplify MCE_GETCLEAR_FLAGS using xchg()
xen/balloon: improve accuracy of initial balloon target for dom0
Partial revert "x86/xen: fix balloon target initialization for PVH dom0"
xen: introduce xen_console_io option
xen/virtio: Don't use grant-dma-ops when running as Dom0
x86/xen/pvh: Enable PAE mode for 32-bit guest only when CONFIG_X86_PAE is set
xen: privcmd: WQ_PERCPU added to alloc_workqueue users
xen/events: replace use of system_wq with system_percpu_wq
Use the linux/platform_data/pic32.h include instead of
asm/mach-pic32/pic32.h so that the asm variant can be dropped. This
is in preparation for allowing some drivers to be compiled on other
architectures with COMPILE_TEST enabled.
Signed-off-by: Brian Masney <bmasney@redhat.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCgA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAml2lQweHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG0dcH/2yLU3IKlHSSgEDL
Qq3oBuRK/zoVOdy+CM+TmTdl2d1LnBd8J547xFStB7kVGf5mEkdFZdHLBSHRnKDf
ia1SGec06kyLpRX6x5T6FsfwOhkBmVsp59X0coM57QWxxenybugtzPvDO2TQ8/G4
buixJI0jJVgwRwXNzWB4n2W6FxNGui2A7gEN2mjtvkM2t/aDkiDjEqB8ve0pZJX9
4EWhxOgRFzwWgkd/bY+4wgXVXEt3GtI+3VvNncRqLIO00A/AnZOYmH4S2RQUDszD
IbyDscYYxloZcZMDXc3PN2WgD9DCGKuP3GpJGsOHbl0DN6JkqI9nwGsOFZKGVOeF
vbajwPE=
=iAOa
-----END PGP SIGNATURE-----
BackMerge tag 'v6.19-rc7' into drm-next
Linux 6.19-rc7
This is needed for msm and rust trees.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This reverts commit d000422a46.
It is reported by many to cause boot failures, so must be reverted.
Cc: Xin Zhao <jackzxcui1989@163.com>
Cc: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/d1942304-ee30-478d-90fb-279519f3ae81@samsung.com
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reported-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On the embedded platform, certain critical data, such as IMU data, is
transmitted through UART. The tty_flip_buffer_push() interface in the TTY
layer uses system_dfl_wq to handle the flipping of the TTY buffer.
Although the unbound workqueue can create new threads on demand and wake
up the kworker thread on an idle CPU, it may be preempted by real-time
tasks or other high-prio tasks.
flush_to_ldisc() needs to wake up the relevant data handle thread. When
executing __wake_up_common_lock(), it calls spin_lock_irqsave(), which
does not disable preemption but disables migration in RT-Linux. This
prevents the kworker thread from being migrated to other cores by CPU's
balancing logic, resulting in long delays. The call trace is as follows:
__wake_up_common_lock
__wake_up
ep_poll_callback
__wake_up_common
__wake_up_common_lock
__wake_up
n_tty_receive_buf_common
n_tty_receive_buf2
tty_ldisc_receive_buf
tty_port_default_receive_buf
flush_to_ldisc
In our system, the processing interval for each frame of IMU data
transmitted via UART can experience significant jitter due to this issue.
Instead of the expected 10 to 15 ms frame processing interval, we see
spikes up to 30 to 35 ms. Moreover, in just one or two hours, there can
be 2 to 3 occurrences of such high jitter, which is quite frequent. This
jitter exceeds the software's tolerable limit of 20 ms.
Introduce flip_wq in tty_port which can be set by tty_port_link_wq() or as
default linked to default workqueue allocated when tty_register_driver().
The default workqueue is allocated with flag WQ_SYSFS, so that cpumask and
nice can be set dynamically. The execution timing of tty_port_link_wq() is
not clearly restricted. The newly added function tty_port_link_driver_wq()
checks whether the flip_wq of the tty_port has already been assigned when
linking the default tty_driver's workqueue to the port. After the user has
set a custom workqueue for a certain tty_port using tty_port_link_wq(), the
system will only use this custom workqueue, even if tty_driver does not
have %TTY_DRIVER_CUSTOM_WORKQUEUE flag.
Introduce %TTY_DRIVER_CUSTOM_WORKQUEUE flag meaning not to create the
default single tty_driver workqueue. Two reasons why need to introduce the
%TTY_DRIVER_CUSTOM_WORKQUEUE flag:
1. If the WQ_SYSFS parameter is enabled, workqueue_sysfs_register() will
fail when trying to create a workqueue with the same name. The pty is an
example of this; if both CONFIG_LEGACY_PTYS and CONFIG_UNIX98_PTYS are
enabled, the call to tty_register_driver() in unix98_pty_init() will fail.
2. Different tty ports may be used for different tasks, which may require
separate core binding control via workqueues. In this case, the workqueue
created by default in the tty driver is unnecessary. Enabling this flag
prevents the creation of this redundant workqueue.
After applying this patch, we can set the related UART TTY flip buffer
workqueue by sysfs. We set the cpumask to CPU cores associated with the
IMU tasks, and set the nice to -20. Testing has shown significant
improvement in the previously described issue, with almost no stuttering
occurring anymore.
Signed-off-by: Xin Zhao <jackzxcui1989@163.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://patch.msgid.link/20251223034836.2625547-1-jackzxcui1989@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As comments mentioned this is old (and actually deprecated) interface
to set custom baud rates. This interface has limitations as it only
allows to set a single opaque value called "custom_divisor". If the HW
needs more complex settings (like fractional divisor) it must somehow
encode this. This is horrid interface that is very driver specific
and not flexible. Meanwhile Linux has established way to set free
baud rate settings via BOTHER [1]. With all this being said, remove
deprecated interface for good.
Link: https://stackoverflow.com/questions/12646324/how-can-i-set-a-custom-baud-rate-on-linux [1]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20260122102349.2395423-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As comments mentioned this is old (and actually deprecated) interface
to set custom baud rates. This interface has limitations as it only
allows to set a single opaque value called "custom_divisor". If the HW
needs more complex settings (like fractional divisor) it must somehow
encode this. This is horrid interface that is very driver specific
and not flexible. Meanwhile Linux has established way to set free
baud rate settings via BOTHER [1]. With all this being said, remove
deprecated interface for good.
Link: https://stackoverflow.com/questions/12646324/how-can-i-set-a-custom-baud-rate-on-linux [1]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20260122102349.2395423-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In TI K3 SoCs, I/O daisy chaining is used to allow wakeup from UART when the
UART controller is off. Set UART device as wakeup capable using out-of-band
wakeup if the 'wakeup' pinctrl state exists and the device may wakeup.
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Kendall Willis <k-willis@ti.com>
Link: https://patch.msgid.link/20260116-uart-wakeup-v2-1-0078ae9996e4@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Revert commit bfc467db60 ("serial: remove redundant
tty_port_link_device()") because the tty_port_link_device() is not
redundant: the tty->port has to be confured before we call
uart_configure_port(), otherwise user-space can open console without TTY
linked to the driver.
This tty_port_link_device() was added explicitly to avoid this exact
issue in commit fb2b90014d ("tty: link tty and port before configuring
it as console"), so offending commit basically reverted the fix saying
it is redundant without addressing the actual race condition presented
there.
Reproducible always as tty->port warning on Qualcomm SoC with most of
devices disabled, so with very fast boot, and one serial device being
the console:
printk: legacy console [ttyMSM0] enabled
printk: legacy console [ttyMSM0] enabled
printk: legacy bootconsole [qcom_geni0] disabled
printk: legacy bootconsole [qcom_geni0] disabled
------------[ cut here ]------------
tty_init_dev: ttyMSM driver does not set tty->port. This would crash the kernel. Fix the driver!
WARNING: drivers/tty/tty_io.c:1414 at tty_init_dev.part.0+0x228/0x25c, CPU#2: systemd/1
Modules linked in: socinfo tcsrcc_eliza gcc_eliza sm3_ce fuse ipv6
CPU: 2 UID: 0 PID: 1 Comm: systemd Tainted: G S 6.19.0-rc4-next-20260108-00024-g2202f4d30aa8 #73 PREEMPT
Tainted: [S]=CPU_OUT_OF_SPEC
Hardware name: Qualcomm Technologies, Inc. Eliza (DT)
...
tty_init_dev.part.0 (drivers/tty/tty_io.c:1414 (discriminator 11)) (P)
tty_open (arch/arm64/include/asm/atomic_ll_sc.h:95 (discriminator 3) drivers/tty/tty_io.c:2073 (discriminator 3) drivers/tty/tty_io.c:2120 (discriminator 3))
chrdev_open (fs/char_dev.c:411)
do_dentry_open (fs/open.c:962)
vfs_open (fs/open.c:1094)
do_open (fs/namei.c:4634)
path_openat (fs/namei.c:4793)
do_filp_open (fs/namei.c:4820)
do_sys_openat2 (fs/open.c:1391 (discriminator 3))
...
Starting Network Name Resolution...
Apparently the flow with this small Yocto-based ramdisk user-space is:
driver (qcom_geni_serial.c): user-space:
============================ ===========
qcom_geni_serial_probe()
uart_add_one_port()
serial_core_register_port()
serial_core_add_one_port()
uart_configure_port()
register_console()
|
| open console
| ...
| tty_init_dev()
| driver->ports[idx] is NULL
|
tty_port_register_device_attr_serdev()
tty_port_link_device() <- set driver->ports[idx]
Fixes: bfc467db60 ("serial: remove redundant tty_port_link_device()")
Cc: stable@vger.kernel.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://patch.msgid.link/20260123072139.53293-2-krzysztof.kozlowski@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove <linux/hex.h> from <linux/kernel.h> and update all users/callers of
hex.h interfaces to directly #include <linux/hex.h> as part of the process
of putting kernel.h on a diet.
Removing hex.h from kernel.h means that 36K C source files don't have to
pay the price of parsing hex.h for the roughly 120 C source files that
need it.
This change has been build-tested with allmodconfig on most ARCHes. Also,
all users/callers of <linux/hex.h> in the entire source tree have been
updated if needed (if not already #included).
Link: https://lkml.kernel.org/r/20251215005206.2362276-1-rdunlap@infradead.org
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Yury Norov (NVIDIA) <yury.norov@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The KMSG_COMPONENT macro is a leftover of the s390 specific "kernel message
catalog" from 2008 [1] which never made it upstream.
The macro was added to s390 code to allow for an out-of-tree patch which
used this to generate unique message ids. Also this out-of-tree doesn't
exist anymore.
Remove the macro in order to get rid of a pointless indirection.
[1] https://lwn.net/Articles/292650/
Acked-by: Hendrik Brueckner <brueckner@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Link: https://patch.msgid.link/20251126142909.2140015-1-hca@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fintek F81504/508/512 can support both RTS_ON_SEND and RTS_AFTER_SEND,
but pci_fintek_rs485_supported only announces the former.
This makes it impossible to unset SER_RS485_RTS_ON_SEND from
userspace because of uart_sanitize_serial_rs485(). Some devices
with these chips need RTS low on TX, so they are effectively broken.
Fix this by announcing the support for SER_RS485_RTS_AFTER_SEND,
similar to commit 068d35a7be ("serial: sc16is7xx: announce support
for SER_RS485_RTS_ON_SEND").
Fixes: 4afeced55b ("serial: core: fix sanitizing check for RTS settings")
Cc: stable <stable@kernel.org>
Signed-off-by: Marnix Rijnart <marnix.rijnart@iwell.eu>
Link: https://patch.msgid.link/20260112000931.61703-1-marnix.rijnart@iwell.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 10904d725f ("serial: qcom-geni: Enable PM runtime for serial
driver") caused BT init to fail during bootup on the RB2 platform,
preventing proper BT initialization. However, BT works correctly after
bootup completes.
The issue occurs when runtime PM is enabled and uart_add_one_port() is
called before wakeup IRQ setup. The uart_add_one_port() call activates
the device through runtime PM, which configures GPIOs to the "qup_x"
pinmux function during runtime resume. When wakeup IRQ registration
happens afterward using dev_pm_set_dedicated_wake_irq(), these GPIOs
are reset back to the "gpio" pinmux function, which impacts the RX GPIO
and leads to Bluetooth failures.
Fix this by ensuring wakeup IRQ setup is completed before calling
uart_add_one_port() to prevent the pinmux function conflict.
Fixes: 10904d725f ("serial: qcom-geni: Enable PM runtime for serial driver")
Reported-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Closes: https://lore.kernel.org/all/20251110101043.2108414-4-praveen.talari@oss.qualcomm.com/
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Praveen Talari <praveen.talari@oss.qualcomm.com>
Link: https://patch.msgid.link/20260108041006.1874757-1-praveen.talari@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clear rx_running flag only after DMA teardown polling completes. In the
previous implementation the flag was being cleared while hardware teardown
was still in progress, creating a mismatch between software state
(flag = 0, "ready") and hardware state (still terminating).
Signed-off-by: Moteen Shah <m-shah@ti.com>
Link: https://patch.msgid.link/20260112081829.63049-3-m-shah@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DMA IRQ handler does not accounts for the overrun(OE) or any other
errors being reported by the IP before triggering a DMA transaction which
leads to the interrupts not being handled resulting into an IRQ storm.
The way to handle OE is to:
1. Reset the RX FIFO.
2. Read the UART_RESUME register, which clears the internal flag
Earlier, the driver issued DMA transations even in case of OE which shouldn't
be done according to the OE handling mechanism mentioned above, as we are
resetting the FIFO's, refer section: "12.1.6.4.8.1.3.6 Overrun During
Receive" [0].
[0] https://www.ti.com/lit/pdf/spruiu1
Signed-off-by: Moteen Shah <m-shah@ti.com>
Link: https://patch.msgid.link/20260112081829.63049-2-m-shah@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Having a prompt of "DMA support" suddenly appear during a
"make oldconfig" can be confusing. Add a little helpful text to
the prompt message.
Fixes: 73a19e4c03 ("serial: sh-sci: Add DMA support.")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260110232643.3533351-5-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Improve the "Non-8250 serial port support" menu so that entries in it
are displayed in a better order (_CONSOLE after its driver) and so that
intervening symbols don't break up the dependency list, allowing menu
entries to be displayed with proper indentation.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://patch.msgid.link/20260110232643.3533351-4-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Improve the "8250/16550 serial support" menu so that entries in it
are displayed in a better order (reorder a few symbols) and so that
intervening symbols don't break up the dependency list, allowing menu
entries to be displayed with proper indentation.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://patch.msgid.link/20260110232643.3533351-3-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SERIAL_IMX_CONSOLE is a build option for the imx driver (SERIAL_IMX).
It does not build a separate console driver file, so it can't be built
as a module since it isn't built at all.
Change the Kconfig symbol from tristate to bool and update the help
text accordingly.
Fixes: 0db4f9b91c ("tty: serial: imx: enable imx serial console port as module")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://patch.msgid.link/20260110232643.3533351-2-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 1f4ea4838b ("mcb: Add missing modpost build support")
the MODULE_ALIAS() is redundant as the module alias is now
automatically generated from the MODULE_DEVICE_TABLE().
Remove the explicit alias.
No functional change intended.
Reviewed-by: Jorge Sanjuan Garcia <dev-jorge.sanjuangarcia@duagon.com>
Signed-off-by: Jose Javier Rodriguez Barbarin <dev-josejavier.rodriguez@duagon.com>
Link: https://patch.msgid.link/20260108134110.25278-3-dev-josejavier.rodriguez@duagon.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 1f4ea4838b ("mcb: Add missing modpost build support")
the MODULE_ALIAS() is redundant as the module alias is now
automatically generated from the MODULE_DEVICE_TABLE().
Remove the explicit alias.
No functional change intended.
Reviewed-by: Jorge Sanjuan Garcia <dev-jorge.sanjuangarcia@duagon.com>
Signed-off-by: Jose Javier Rodriguez Barbarin <dev-josejavier.rodriguez@duagon.com>
Link: https://patch.msgid.link/20260108134110.25278-2-dev-josejavier.rodriguez@duagon.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Xen can support console_io hypercalls for any domains, not just dom0,
depending on DEBUG and XSM policies. These hypercalls can be very useful
for development and debugging.
Introduce a kernel command line option xen_console_io to enable the
usage of console_io hypercalls for any domain upon request. When
xen_console_io is not specified, the current behavior is retained.
Signed-off-by: Stefano Stabellini <stefano.stabellini@amd.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Message-ID: <alpine.DEB.2.22.394.2601131522540.992863@ubuntu-linux-20-04-desktop>
RTS line control with delay should be triggered when there is no more
bytes in kfifo and hardware buffer is empty. Without this patch RTS
control is scheduled right after feeding hardware buffer and this is too
early.
RTS line may change state before hardware buffer is empty.
With this patch delayed RTS state change is triggered when function
cdns_uart_handle_tx is called from cdns_uart_isr on
CDNS_UART_IXR_TXEMPTY exactly when hardware completed transmission
Fixes: fccc9d9233 ("tty: serial: uartps: Add rs485 support to uartps driver")
Cc: stable <stable@kernel.org>
Link: https://patch.msgid.link/20251221103221.1971125-1-jakub.turek@elsta.tech
Signed-off-by: Jakub Turek <jakub.turek@elsta.tech>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver updates struct sci_port::tx_cookie to zero right before the TX
work is scheduled, or to -EINVAL when DMA is disabled.
dma_async_is_complete(), called through dma_cookie_status() (and possibly
through dmaengine_tx_status()), considers cookies valid only if they have
values greater than or equal to 1.
Passing zero or -EINVAL to dmaengine_tx_status() before any TX DMA
transfer has started leads to an incorrect TX status being reported, as the
cookie is invalid for the DMA subsystem. This may cause long wait times
when the serial device is opened for configuration before any TX activity
has occurred.
Check that the TX cookie is valid before passing it to
dmaengine_tx_status().
Fixes: 7cc0e0a43a ("serial: sh-sci: Check if TX data was written to device in .tx_empty()")
Cc: stable <stable@kernel.org>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://patch.msgid.link/20251217135759.402015-1-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During restoring sysfs fwnode information the information of_node_reused
was dropped. This was previously set by device_set_of_node_from_dev().
Add it back manually
Fixes: 24ec03cc55 ("serial: core: Restore sysfs fwnode information")
Cc: stable <stable@kernel.org>
Suggested-by: Cosmin Tanislav <demonsingur@gmail.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Tested-by: Michael Walle <mwalle@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Cosmin Tanislav <demonsingur@gmail.com>
Link: https://patch.msgid.link/20251219152813.1893982-1-alexander.stein@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are no implementations of con_debug_enter and con_debug_leave.
Remove the callbacks from struct consw and clean up the caller.
This is a functional revert of commit b45cfba4e9 ("vt,console,kdb:
implement atomic console enter/leave functions").
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://patch.msgid.link/20251208102851.40894-3-tzimmermann@suse.de
The devm_platform_get_and_ioremap_resource() function never returns
NULL, it returns error pointers. Fix the error checking to match.
Fixes: 25e95d7631 ("serial: 8250: Add Loongson uart driver support")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://patch.msgid.link/aSsIa3KdAlXh5uQC@stanley.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The change that restores sysfs fwnode information does it only for OF cases.
Update the fix to cover all possible types of fwnodes.
Fixes: d36f0e9a00 ("serial: core: restore of_node information in sysfs")
Cc: stable <stable@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20251127163650.2942075-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To prepare serdev driver to migrate away from struct device_driver::shutdown
(and then eventually remove that callback) create a serdev driver shutdown
callback and migration code to keep the existing behaviour. Note this
introduces a warning for each driver at register time that isn't converted
yet to that callback.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/ab518883e3ed0976a19cb5b5b5faf42bd3a655b7.1765526117.git.u.kleine-koenig@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for RZ/G3E RSCI. RSCI IP found on the RZ/G3E SoC is similar
to RZ/T2H, but it has a 32-stage FIFO. It has 6 clocks(5 module clocks
+ 1 external clock) instead of 3 clocks(2 module clocks + 1 external
clock) on T2H, has 6 irqs compared to 4 on RZ/T2H and has multiple resets.
Add support for the hardware flow control.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://patch.msgid.link/20251129164325.209213-18-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rename rsci_early_console_setup()->rsci_rzt2h_early_console_setup(),
the early_console data of_sci_rsci_data->of_rsci_rzt2h_data and the
port_params rsci_port_params->rsci_rzt2h_port_params to support RZ/G3E
RSCI that uses different data and callback().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://patch.msgid.link/20251129164325.209213-17-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add finish_console_write() callback as RZ/G3E RSCI IP needs special
handling compared to other SoCs.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://patch.msgid.link/20251129164325.209213-16-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make the function sci_scbrr_calc() public for code reuse to support RZ/G3E
RSCI IP.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://patch.msgid.link/20251129164325.209213-15-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The RZ/G3E RSCI IP has 32-stage FIFO compared to 16-stage FIFO on RZ/T2H.
Add RSCI_PORT_SCIF32 port ID to differentiate it from RZ/T2H RSCI and
update sci_is_rsci_type() and sci_is_fifo_type()
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://patch.msgid.link/20251129164325.209213-13-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rename port SCI_PORT_RSCI->RSCI_PORT_SCIF16 to differentiate it from
RZ/G3E port that has 32-stage FIFO.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://patch.msgid.link/20251129164325.209213-12-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add sci_is_rsci_type() for RSCI port type. This will simplify the code
when the support added for RSCI_PORT_SCIF32 private PORT type.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://patch.msgid.link/20251129164325.209213-11-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace devm_*_get_exclusive()->devm_*_array_get_exclusive() to support
existing SoCs along with RZ/G3E as RZ/G3E has 2 resets.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://patch.msgid.link/20251129164325.209213-10-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Shorten the number lines in sci_init_clocks() by fitting the error
messages within an 100-character length limit.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://patch.msgid.link/20251129164325.209213-7-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop rsci_clear_SCxSR by reusing rsci_clear_CFC() as the contents of
both functions are the same.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://patch.msgid.link/20251129164325.209213-6-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ports that support FIFO has fifosize > 1. Replace checking the port type
with fifosize for device file{create, remove}.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://patch.msgid.link/20251129164325.209213-5-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The rtrg variable is populated in sci_init_single() for RZ/T2H. Add
set_rtrg() callback for setting the rtrg value.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://patch.msgid.link/20251129164325.209213-4-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The RZ/T2H RSCI has 16-stage FIFO. Like other SoCs, set the default
rx_trigger as the fifosize.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://patch.msgid.link/20251129164325.209213-3-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add missing descriptions for write_work and tty_for_write_work
members in struct n_hdlc.
This fixes the following warnings:
drivers/tty/n_hdlc.c: warning: Function parameter or member
'write_work' not described in 'n_hdlc'
drivers/tty/n_hdlc.c: warning: Function parameter or member
'tty_for_write_work' not described in 'n_hdlc'
Signed-off-by: Bartlomiej Kubik <kubik.bartlomiej@gmail.com>
Link: https://patch.msgid.link/20251202063748.1210359-1-kubik.bartlomiej@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify the probe() code by using dev_err_probe().
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Gerhard Engleder <eg@keba.com>
Link: https://patch.msgid.link/20251216193726.55449-4-gerhard@engleder-embedded.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add defines for better readability of the Indexed Control Register (ICR)
access. In enhanced mode SCR and LSR registers are used for ICR access.
The behavior of these register is different in this mode and that shall
be documented with dedicated defines.
Suggested-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Gerhard Engleder <eg@keba.com>
Link: https://patch.msgid.link/20251216193726.55449-3-gerhard@engleder-embedded.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andy and Ilpo suggested to add missing includes, because the code shall
not rely on indirect includes. Add missing includes and remove one
include, which only enabled indirect includes.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Suggested-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Gerhard Engleder <eg@keba.com>
Link: https://patch.msgid.link/20251216193726.55449-2-gerhard@engleder-embedded.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Z125 define is not used anywhere, thus removed. Also used a
more specific name for the maximum number of ports per unit and
removed the duplicated define MAX_PORTS
Reviewed-by: Jose Javier Rodriguez Barbarin <dev-josejavier.rodriguez@duagon.com>
Signed-off-by: Filip Jensen <dev-Felipe.Jensen@duagon.com>
Link: https://patch.msgid.link/20251210164804.94801-2-dev-Felipe.Jensen@duagon.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit bfb24564b5 ("tty: vt/keyboard: use __free()"), builds
using asm goto for put_user() and get_user() with a version of clang
older than 17 error with:
drivers/tty/vt/keyboard.c:1709:7: error: cannot jump from this asm goto statement to one of its possible targets
if (put_user(asize, &a->kb_cnt))
^
...
arch/arm64/include/asm/uaccess.h:298:2: note: expanded from macro '__put_mem_asm'
asm goto( \
^
drivers/tty/vt/keyboard.c:1687:7: note: possible target of asm goto statement
if (put_user(asize, &a->kb_cnt))
^
...
arch/arm64/include/asm/uaccess.h:342:2: note: expanded from macro '__raw_put_user'
__rpu_failed: \
^
drivers/tty/vt/keyboard.c:1697:23: note: jump exits scope of variable with __attribute__((cleanup))
void __free(kfree) *buf = kmalloc_array(MAX_DIACR, sizeof(struct kbdiacruc),
^
drivers/tty/vt/keyboard.c:1671:33: note: jump bypasses initialization of variable with __attribute__((cleanup))
struct kbdiacr __free(kfree) *dia = kmalloc_array(MAX_DIACR, sizeof(struct kbdiacr),
^
Prior to a fix to clang's scope checker in clang 17 [1], all labels in a
function were validated as potential targets of all asm gotos in a
function, regardless of whether they actually were a target of an asm
goto call, resulting in false positive errors about skipping over
variables marked with the cleanup attribute.
To workaround this error, split up the bodies of the case statements in
vt_do_diacrit() into their own functions so that the scope checker does
not trip up on the multiple instances of __free().
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202509091702.Oc7eCRDw-lkp@intel.com/
Closes: https://lore.kernel.org/oe-kbuild-all/202511241835.EA8lShgH-lkp@intel.com/
Link: f023f5cdb2 [1]
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://patch.msgid.link/20251125-tty-vt-keyboard-wa-clang-scope-check-error-v1-1-f5a5ea55c578@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move pm_runtime_set_active() call earlier in probe to simplify error
handling and add proper error checking to ensure the device is marked
as active before any runtime PM operations can occur.
Additionally, replace the const struct dev_pm_ops declaration with
_DEFINE_DEV_PM_OPS macro for better consistency with modern kernel PM
patterns.
Signed-off-by: Artem Shimko <a.shimko.dev@gmail.com>
Link: https://patch.msgid.link/20251104145433.2316165-3-a.shimko.dev@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add error checking for clk_prepare_enable() calls in
dw8250_runtime_resume(). Currently if either clock fails to enable,
the function returns success while leaving clocks in inconsistent state.
This change implements comprehensive error handling by checking the return
values of both clk_prepare_enable() calls. If the second clock enable
operation fails after the first clock has already been successfully
enabled, the code now properly cleans up by disabling and unpreparing
the first clock before returning. The error code is then propagated to
the caller, ensuring that clock enable failures are properly reported
rather than being silently ignored.
Signed-off-by: Artem Shimko <a.shimko.dev@gmail.com>
Link: https://patch.msgid.link/20251104145433.2316165-2-a.shimko.dev@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of tty/serial driver changes for 6.19-rc1. Nothing
major at all, just small constant churn to make the tty layer "cleaner"
as well as serial driver updates and even a new test added! Included in
here are:
- More tty/serial cleanups from Jiri
- tty tiocsti test added to hopefully ensure we don't regress in this
area again
- sc16is7xx driver updates
- imx serial driver updates
- 8250 driver updates
- new hardware device ids added
- other minor serial/tty driver cleanups and tweaks
All of these have been in linux-next for a while with no reported issues
other than a merge-conflict that you will have when you merge into your
tree (should be simple to resolve, just delete the code on both sides
of the merge).
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCaTTJ+g8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymiEQCgweRHAivbv2avIlfsmpFewV27WMgAnR1aE5mW
JhhopcWcdjnRJikavHGo
=lhK0
-----END PGP SIGNATURE-----
Merge tag 'tty-6.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the big set of tty/serial driver changes for 6.19-rc1. Nothing
major at all, just small constant churn to make the tty layer
"cleaner" as well as serial driver updates and even a new test added!
Included in here are:
- More tty/serial cleanups from Jiri
- tty tiocsti test added to hopefully ensure we don't regress in this
area again
- sc16is7xx driver updates
- imx serial driver updates
- 8250 driver updates
- new hardware device ids added
- other minor serial/tty driver cleanups and tweaks
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-6.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (60 commits)
serial: sh-sci: Fix deadlock during RSCI FIFO overrun error
dt-bindings: serial: rsci: Drop "uart-has-rtscts: false"
LoongArch: dts: Add uart new compatible string
serial: 8250: Add Loongson uart driver support
dt-bindings: serial: 8250: Add Loongson uart compatible
serial: 8250: add driver for KEBA UART
serial: Keep rs485 settings for devices without firmware node
serial: qcom-geni: Enable Serial on SA8255p Qualcomm platforms
serial: qcom-geni: Enable PM runtime for serial driver
serial: sprd: Return -EPROBE_DEFER when uart clock is not ready
tty: serial: samsung: Declare earlycon for Exynos850
serial: icom: Convert PCIBIOS_* return codes to errnos
serial: 8250-of: Fix style issues in 8250_of.c
serial: add support of CPCI cards
serial: mux: Fix kernel doc for mux_poll()
tty: replace use of system_unbound_wq with system_dfl_wq
serial: 8250_platform: simplify IRQF_SHARED handling
serial: 8250: make share_irqs local to 8250_platform
serial: 8250: move skip_txen_test to core
serial: drop SERIAL_8250_DEPRECATED_OPTIONS
...
-----BEGIN PGP SIGNATURE-----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=qSzr
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.19-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Enable host bridge emulation for PCI_DOMAINS_GENERIC platforms (Dan
Williams)
- Switch vmd from custom domain number allocator to the common
allocator to prevent a potential race with new non-VMD buses (Dan
Williams)
- Enable Precision Time Measurement (PTM) only if device advertises
support for a relevant role, to prevent invalid PTM Requests that
cause ACS violations that are reported as AER Uncorrectable
Non-Fatal errors (Mika Westerberg)
Resource management:
- Prevent resource tree corruption when BAR resize fails (Ilpo
Järvinen)
- Restore BARs to the original size if a BAR resize fails (Ilpo
Järvinen)
- Remove BAR release from BAR resize attempts by the xe, i915, and
amdgpu drivers so the PCI core can restore BARs if the resize fails
(Ilpo Järvinen)
- Move Resizable BAR code to rebar.c (Ilpo Järvinen)
- Add pci_rebar_size_supported() and use it in i915 and xe (Ilpo
Järvinen)
- Add pci_rebar_get_max_size() and use it in xe and amdgpu (Ilpo
Järvinen)
Power management and error handling:
- For drivers using PCI legacy suspend, save config state at suspend
so that state (not any earlier state from enumeration, probe, or
error recovery) will be restored when resuming (Lukas Wunner)
- For devices with no driver or a driver that lacks power management,
save config state at hibernate so that state (not any earlier state
from enumeration, probe, or error recovery) will be restored when
resuming (Lukas Wunner)
- Save device config space on device addition, before driver binding,
so error recovery works more reliably (Lukas Wunner)
- Drop pci_save_state() from several drivers that no longer need it
since the PCI core always does it and pci_restore_state() no longer
invalidates the saved state (Lukas Wunner)
- Document use of pci_save_state() by drivers to capture the state
they want restored during error recovery (Lukas Wunner)
Power control:
- Add a struct pci_ops.assert_perst() function pointer to
assert/deassert PCIe PERST# and implement it for the qcom driver
(Krishna Chaitanya Chundru)
- Add DT binding and pwrctrl driver for the Toshiba TC9563 PCIe
switch, which must be held in reset after poweron so the pwrctrl
driver can configure the switch via I2C before bringing up the
links (Krishna Chaitanya Chundru)
Endpoint framework:
- Convert the endpoint doorbell test to use a threaded IRQ to fix a
'sleeping while atomic' issue (Bhanu Seshu Kumar Valluri)
- Add endpoint VNTB MSI doorbell support to reduce latency between
host and endpoint (Frank Li)
New native PCIe controller drivers:
- Add CIX Sky1 host controller DT binding and driver (Hans Zhang)
- Add NXP S32G host controller DT binding and driver (Vincent
Guittot)
- Add Renesas RZ/G3S host controller DT binding and driver (Claudiu
Beznea)
- Add SpacemiT K1 host controller DT binding and driver (Alex Elder)
Amlogic Meson PCIe controller driver:
- Update DT binding to name DBI region 'dbi', not 'elbi', and update
driver to support both (Manivannan Sadhasivam)
Apple PCIe controller driver:
- Move struct pci_host_bridge allocation from pci_host_common_init()
to callers, which significantly simplifies pcie-apple (Marc
Zyngier)
Broadcom STB PCIe controller driver:
- Disable advertising ASPM L0s support correctly (Jim Quinlan)
- Add a panic/die handler to print diagnostic info in case PCIe
caused an unrecoverable abort (Jim Quinlan)
Cadence PCIe controller driver:
- Add module support for Cadence platform host and endpoint
controller driver (Manikandan K Pillai)
- Split headers into 'legacy' (LGA) and 'high perf' (HPA) to prepare
for new CIX Sky1 driver (Manikandan K Pillai)
MediaTek PCIe controller driver:
- Convert DT binding to YAML schema (Christian Marangi)
- Add Airoha AN7583 DT compatible and driver support (Christian
Marangi)
Qualcomm PCIe controller driver:
- Add Qualcomm Kaanapali to SM8550 DT binding (Qiang Yu)
- Add required 'power-domains' and 'resets' to qcom sa8775p, sc7280,
sc8280xp, sm8150, sm8250, sm8350, sm8450, sm8550, x1e80100 DT
schemas (Krzysztof Kozlowski)
- Look up OPP using both frequency and data rate (not just frequency)
so RPMh votes can account for both (Krishna Chaitanya Chundru)
Rockchip DesignWare PCIe controller driver:
- Add Rockchip RK3528 compatible strings in DT binding (Yao Zi)
STMicroelectronics STM32MP25 PCIe controller driver:
- Fix a race between link training and endpoint register
initialization (Christian Bruel)
- Align endpoint allocations to match the ATU requirements (Christian
Bruel)
Synopsys DesignWare PCIe controller driver:
- Clear L1 PM Substate Capability 'Supported' bits unless glue driver
says it's supported, which prevents users from enabling non-working
L1SS. Currently only qcom and tegra194 support L1SS (Bjorn Helgaas)
- Remove now-superfluous L1SS disable code from tegra194 (Bjorn
Helgaas)
- Configure L1SS support in dw-rockchip when DT says
'supports-clkreq' (Shawn Lin)
TI Keystone PCIe controller driver:
- Fail the probe instead of silently succeeding if ks_pcie_of_data
didn't specify Root Complex or Endpoint mode (Siddharth Vadapalli)
- Make keystone buildable as a loadable module, except on ARM32 where
hook_fault_code() is __init (Siddharth Vadapalli)"
* tag 'pci-v6.19-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (100 commits)
MAINTAINERS: Add Manivannan Sadhasivam as PCI/pwrctrl maintainer
MAINTAINERS: Add CIX Sky1 PCIe controller driver maintainer
PCI: sky1: Add PCIe host support for CIX Sky1
dt-bindings: PCI: Add CIX Sky1 PCIe Root Complex bindings
PCI: cadence: Add support for High Perf Architecture (HPA) controller
MAINTAINERS: Add NXP S32G PCIe controller driver maintainer
PCI: s32g: Add NXP S32G PCIe controller driver (RC)
PCI: dwc: Add register and bitfield definitions
dt-bindings: PCI: s32g: Add NXP S32G PCIe controller
PCI: Add Renesas RZ/G3S host controller driver
PCI: host-generic: Move bridge allocation outside of pci_host_common_init()
dt-bindings: PCI: Add Renesas RZ/G3S PCIe controller binding
PCI: Validate pci_rebar_size_supported() input
Documentation: PCI: Amend error recovery doc with pci_save_state() rules
treewide: Drop pci_save_state() after pci_restore_state()
PCI/ERR: Ensure error recoverability at all times
PCI/PM: Stop needlessly clearing state_saved on enumeration and thaw
PCI/PM: Reinstate clearing state_saved in legacy and !PM codepaths
PCI: dw-rockchip: Configure L1SS support
PCI: tegra194: Remove unnecessary L1SS disable code
...
-----BEGIN PGP SIGNATURE-----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=FnfO
-----END PGP SIGNATURE-----
Merge tag 'printk-for-6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux
Pull printk updates from Petr Mladek:
- Allow creaing nbcon console drivers with an unsafe write_atomic()
callback that can only be called by the final nbcon_atomic_flush_unsafe().
Otherwise, the driver would rely on the kthread.
It is going to be used as the-best-effort approach for an
experimental nbcon netconsole driver, see
https://lore.kernel.org/r/20251121-nbcon-v1-2-503d17b2b4af@debian.org
Note that a safe .write_atomic() callback is supposed to work in NMI
context. But some networking drivers are not safe even in IRQ
context:
https://lore.kernel.org/r/oc46gdpmmlly5o44obvmoatfqo5bhpgv7pabpvb6sjuqioymcg@gjsma3ghoz35
In an ideal world, all networking drivers would be fixed first and
the atomic flush would be blocked only in NMI context. But it brings
the question how reliable networking drivers are when the system is
in a bad state. They might block flushing more reliable serial
consoles which are more suitable for serious debugging anyway.
- Allow to use the last 4 bytes of the printk ring buffer.
- Prevent queuing IRQ work and block printk kthreads when consoles are
suspended. Otherwise, they create non-necessary churn or even block
the suspend.
- Release console_lock() between each record in the kthread used for
legacy consoles on RT. It might significantly speed up the boot.
- Release nbcon context between each record in the atomic flush. It
prevents stalls of the related printk kthread after it has lost the
ownership in the middle of a record
- Add support for NBCON consoles into KDB
- Add %ptsP modifier for printing struct timespec64 and use it where
possible
- Misc code clean up
* tag 'printk-for-6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux: (48 commits)
printk: Use console_is_usable on console_unblank
arch: um: kmsg_dump: Use console_is_usable
drivers: serial: kgdboc: Drop checks for CON_ENABLED and CON_BOOT
lib/vsprintf: Unify FORMAT_STATE_NUM handlers
printk: Avoid irq_work for printk_deferred() on suspend
printk: Avoid scheduling irq_work on suspend
printk: Allow printk_trigger_flush() to flush all types
tracing: Switch to use %ptSp
scsi: snic: Switch to use %ptSp
scsi: fnic: Switch to use %ptSp
s390/dasd: Switch to use %ptSp
ptp: ocp: Switch to use %ptSp
pps: Switch to use %ptSp
PCI: epf-test: Switch to use %ptSp
net: dsa: sja1105: Switch to use %ptSp
mmc: mmc_test: Switch to use %ptSp
media: av7110: Switch to use %ptSp
ipmi: Switch to use %ptSp
igb: Switch to use %ptSp
e1000e: Switch to use %ptSp
...
- klp-build livepatch module generation (Josh Poimboeuf)
Introduce new objtool features and a klp-build
script to generate livepatch modules using a
source .patch as input.
This builds on concepts from the longstanding out-of-tree
kpatch project which began in 2012 and has been used for
many years to generate livepatch modules for production kernels.
However, this is a complete rewrite which incorporates
hard-earned lessons from 12+ years of maintaining kpatch.
Key improvements compared to kpatch-build:
- Integrated with objtool: Leverages objtool's existing control-flow
graph analysis to help detect changed functions.
- Works on vmlinux.o: Supports late-linked objects, making it
compatible with LTO, IBT, and similar.
- Simplified code base: ~3k fewer lines of code.
- Upstream: No more out-of-tree #ifdef hacks, far less cruft.
- Cleaner internals: Vastly simplified logic for symbol/section/reloc
inclusion and special section extraction.
- Robust __LINE__ macro handling: Avoids false positive binary diffs
caused by the __LINE__ macro by introducing a fix-patch-lines script
which injects #line directives into the source .patch to preserve
the original line numbers at compile time.
- Disassemble code with libopcodes instead of running objdump
(Alexandre Chartre)
- Disassemble support (-d option to objtool) by Alexandre Chartre,
which supports the decoding of various Linux kernel code generation
specials such as alternatives:
17ef: sched_balance_find_dst_group+0x62f mov 0x34(%r9),%edx
17f3: sched_balance_find_dst_group+0x633 | <alternative.17f3> | X86_FEATURE_POPCNT
17f3: sched_balance_find_dst_group+0x633 | call 0x17f8 <__sw_hweight64> | popcnt %rdi,%rax
17f8: sched_balance_find_dst_group+0x638 cmp %eax,%edx
... jump table alternatives:
1895: sched_use_asym_prio+0x5 test $0x8,%ch
1898: sched_use_asym_prio+0x8 je 0x18a9 <sched_use_asym_prio+0x19>
189a: sched_use_asym_prio+0xa | <jump_table.189a> | JUMP
189a: sched_use_asym_prio+0xa | jmp 0x18ae <sched_use_asym_prio+0x1e> | nop2
189c: sched_use_asym_prio+0xc mov $0x1,%eax
18a1: sched_use_asym_prio+0x11 and $0x80,%ecx
... exception table alternatives:
native_read_msr:
5b80: native_read_msr+0x0 mov %edi,%ecx
5b82: native_read_msr+0x2 | <ex_table.5b82> | EXCEPTION
5b82: native_read_msr+0x2 | rdmsr | resume at 0x5b84 <native_read_msr+0x4>
5b84: native_read_msr+0x4 shl $0x20,%rdx
.... x86 feature flag decoding (also see the X86_FEATURE_POPCNT
example in sched_balance_find_dst_group() above):
2faaf: start_thread_common.constprop.0+0x1f jne 0x2fba4 <start_thread_common.constprop.0+0x114>
2fab5: start_thread_common.constprop.0+0x25 | <alternative.2fab5> | X86_FEATURE_ALWAYS | X86_BUG_NULL_SEG
2fab5: start_thread_common.constprop.0+0x25 | jmp 0x2faba <.altinstr_aux+0x2f4> | jmp 0x4b0 <start_thread_common.constprop.0+0x3f> | nop5
2faba: start_thread_common.constprop.0+0x2a mov $0x2b,%eax
... NOP sequence shortening:
1048e2: snapshot_write_finalize+0xc2 je 0x104917 <snapshot_write_finalize+0xf7>
1048e4: snapshot_write_finalize+0xc4 nop6
1048ea: snapshot_write_finalize+0xca nop11
1048f5: snapshot_write_finalize+0xd5 nop11
104900: snapshot_write_finalize+0xe0 mov %rax,%rcx
104903: snapshot_write_finalize+0xe3 mov 0x10(%rdx),%rax
... and much more.
- Function validation tracing support (Alexandre Chartre)
- Various -ffunction-sections fixes (Josh Poimboeuf)
- Clang AutoFDO (Automated Feedback-Directed Optimizations) support (Josh Poimboeuf)
- Misc fixes and cleanups (Borislav Petkov, Chen Ni,
Dylan Hatch, Ingo Molnar, John Wang, Josh Poimboeuf,
Pankaj Raghav, Peter Zijlstra, Thorsten Blum)
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=yPrS
-----END PGP SIGNATURE-----
Merge tag 'objtool-core-2025-12-01' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull objtool updates from Ingo Molnar:
- klp-build livepatch module generation (Josh Poimboeuf)
Introduce new objtool features and a klp-build script to generate
livepatch modules using a source .patch as input.
This builds on concepts from the longstanding out-of-tree kpatch
project which began in 2012 and has been used for many years to
generate livepatch modules for production kernels. However, this is a
complete rewrite which incorporates hard-earned lessons from 12+
years of maintaining kpatch.
Key improvements compared to kpatch-build:
- Integrated with objtool: Leverages objtool's existing control-flow
graph analysis to help detect changed functions.
- Works on vmlinux.o: Supports late-linked objects, making it
compatible with LTO, IBT, and similar.
- Simplified code base: ~3k fewer lines of code.
- Upstream: No more out-of-tree #ifdef hacks, far less cruft.
- Cleaner internals: Vastly simplified logic for
symbol/section/reloc inclusion and special section extraction.
- Robust __LINE__ macro handling: Avoids false positive binary diffs
caused by the __LINE__ macro by introducing a fix-patch-lines
script which injects #line directives into the source .patch to
preserve the original line numbers at compile time.
- Disassemble code with libopcodes instead of running objdump
(Alexandre Chartre)
- Disassemble support (-d option to objtool) by Alexandre Chartre,
which supports the decoding of various Linux kernel code generation
specials such as alternatives:
17ef: sched_balance_find_dst_group+0x62f mov 0x34(%r9),%edx
17f3: sched_balance_find_dst_group+0x633 | <alternative.17f3> | X86_FEATURE_POPCNT
17f3: sched_balance_find_dst_group+0x633 | call 0x17f8 <__sw_hweight64> | popcnt %rdi,%rax
17f8: sched_balance_find_dst_group+0x638 cmp %eax,%edx
... jump table alternatives:
1895: sched_use_asym_prio+0x5 test $0x8,%ch
1898: sched_use_asym_prio+0x8 je 0x18a9 <sched_use_asym_prio+0x19>
189a: sched_use_asym_prio+0xa | <jump_table.189a> | JUMP
189a: sched_use_asym_prio+0xa | jmp 0x18ae <sched_use_asym_prio+0x1e> | nop2
189c: sched_use_asym_prio+0xc mov $0x1,%eax
18a1: sched_use_asym_prio+0x11 and $0x80,%ecx
... exception table alternatives:
native_read_msr:
5b80: native_read_msr+0x0 mov %edi,%ecx
5b82: native_read_msr+0x2 | <ex_table.5b82> | EXCEPTION
5b82: native_read_msr+0x2 | rdmsr | resume at 0x5b84 <native_read_msr+0x4>
5b84: native_read_msr+0x4 shl $0x20,%rdx
.... x86 feature flag decoding (also see the X86_FEATURE_POPCNT
example in sched_balance_find_dst_group() above):
2faaf: start_thread_common.constprop.0+0x1f jne 0x2fba4 <start_thread_common.constprop.0+0x114>
2fab5: start_thread_common.constprop.0+0x25 | <alternative.2fab5> | X86_FEATURE_ALWAYS | X86_BUG_NULL_SEG
2fab5: start_thread_common.constprop.0+0x25 | jmp 0x2faba <.altinstr_aux+0x2f4> | jmp 0x4b0 <start_thread_common.constprop.0+0x3f> | nop5
2faba: start_thread_common.constprop.0+0x2a mov $0x2b,%eax
... NOP sequence shortening:
1048e2: snapshot_write_finalize+0xc2 je 0x104917 <snapshot_write_finalize+0xf7>
1048e4: snapshot_write_finalize+0xc4 nop6
1048ea: snapshot_write_finalize+0xca nop11
1048f5: snapshot_write_finalize+0xd5 nop11
104900: snapshot_write_finalize+0xe0 mov %rax,%rcx
104903: snapshot_write_finalize+0xe3 mov 0x10(%rdx),%rax
... and much more.
- Function validation tracing support (Alexandre Chartre)
- Various -ffunction-sections fixes (Josh Poimboeuf)
- Clang AutoFDO (Automated Feedback-Directed Optimizations) support
(Josh Poimboeuf)
- Misc fixes and cleanups (Borislav Petkov, Chen Ni, Dylan Hatch, Ingo
Molnar, John Wang, Josh Poimboeuf, Pankaj Raghav, Peter Zijlstra,
Thorsten Blum)
* tag 'objtool-core-2025-12-01' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (129 commits)
objtool: Fix segfault on unknown alternatives
objtool: Build with disassembly can fail when including bdf.h
objtool: Trim trailing NOPs in alternative
objtool: Add wide output for disassembly
objtool: Compact output for alternatives with one instruction
objtool: Improve naming of group alternatives
objtool: Add Function to get the name of a CPU feature
objtool: Provide access to feature and flags of group alternatives
objtool: Fix address references in alternatives
objtool: Disassemble jump table alternatives
objtool: Disassemble exception table alternatives
objtool: Print addresses with alternative instructions
objtool: Disassemble group alternatives
objtool: Print headers for alternatives
objtool: Preserve alternatives order
objtool: Add the --disas=<function-pattern> action
objtool: Do not validate IBT for .return_sites and .call_sites
objtool: Improve tracing of alternative instructions
objtool: Add functions to better name alternatives
objtool: Identify the different types of alternatives
...
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRAhzRXHqcMeLMyaSiRxhvAZXjcogUCaSmOZwAKCRCRxhvAZXjc
op0AAP4oNVJkFyvgKoPos5K2EGFB8M7merGhpYtsOoeg8UK6OwD/UySQErHsXQDR
sUDDa5uFOhfrkcfM8REtAN4wF8p5qAc=
=QgFD
-----END PGP SIGNATURE-----
Merge tag 'vfs-6.19-rc1.fd_prepare.fs' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs
Pull fd prepare updates from Christian Brauner:
"This adds the FD_ADD() and FD_PREPARE() primitive. They simplify the
common pattern of get_unused_fd_flags() + create file + fd_install()
that is used extensively throughout the kernel and currently requires
cumbersome cleanup paths.
FD_ADD() - For simple cases where a file is installed immediately:
fd = FD_ADD(O_CLOEXEC, vfio_device_open_file(device));
if (fd < 0)
vfio_device_put_registration(device);
return fd;
FD_PREPARE() - For cases requiring access to the fd or file, or
additional work before publishing:
FD_PREPARE(fdf, O_CLOEXEC, sync_file->file);
if (fdf.err) {
fput(sync_file->file);
return fdf.err;
}
data.fence = fd_prepare_fd(fdf);
if (copy_to_user((void __user *)arg, &data, sizeof(data)))
return -EFAULT;
return fd_publish(fdf);
The primitives are centered around struct fd_prepare. FD_PREPARE()
encapsulates all allocation and cleanup logic and must be followed by
a call to fd_publish() which associates the fd with the file and
installs it into the caller's fdtable. If fd_publish() isn't called,
both are deallocated automatically. FD_ADD() is a shorthand that does
fd_publish() immediately and never exposes the struct to the caller.
I've implemented this in a way that it's compatible with the cleanup
infrastructure while also being usable separately. IOW, it's centered
around struct fd_prepare which is aliased to class_fd_prepare_t and so
we can make use of all the basica guard infrastructure"
* tag 'vfs-6.19-rc1.fd_prepare.fs' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs: (42 commits)
io_uring: convert io_create_mock_file() to FD_PREPARE()
file: convert replace_fd() to FD_PREPARE()
vfio: convert vfio_group_ioctl_get_device_fd() to FD_ADD()
tty: convert ptm_open_peer() to FD_ADD()
ntsync: convert ntsync_obj_get_fd() to FD_PREPARE()
media: convert media_request_alloc() to FD_PREPARE()
hv: convert mshv_ioctl_create_partition() to FD_ADD()
gpio: convert linehandle_create() to FD_PREPARE()
pseries: port papr_rtas_setup_file_interface() to FD_ADD()
pseries: convert papr_platform_dump_create_handle() to FD_ADD()
spufs: convert spufs_gang_open() to FD_PREPARE()
papr-hvpipe: convert papr_hvpipe_dev_create_handle() to FD_PREPARE()
spufs: convert spufs_context_open() to FD_PREPARE()
net/socket: convert __sys_accept4_file() to FD_ADD()
net/socket: convert sock_map_fd() to FD_ADD()
net/kcm: convert kcm_ioctl() to FD_PREPARE()
net/handshake: convert handshake_nl_accept_doit() to FD_PREPARE()
secretmem: convert memfd_secret() to FD_ADD()
memfd: convert memfd_create() to FD_ADD()
bpf: convert bpf_token_create() to FD_PREPARE()
...
The original code tried to find a console that has CON_BOOT _or_
CON_ENABLED flag set. The flag CON_ENABLED is set to all registered
consoles, so in this case this check is always true, even for the
CON_BOOT consoles.
The initial intent of the kgdboc_earlycon_init was to get a console
early (CON_BOOT) or later on in the process (CON_ENABLED). The
code was using for_each_console macro, meaning that all console structs
were previously registered on the printk() machinery. At this point,
any console found on for_each_console is safe for kgdboc_earlycon_init
to use.
Dropping the check makes the code cleaner, and avoids further confusion
by future readers of the code.
Signed-off-by: Marcos Paulo de Souza <mpdesouza@suse.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Link: https://patch.msgid.link/20251121-printk-cleanup-part2-v2-1-57b8b78647f4@suse.com
Signed-off-by: Petr Mladek <pmladek@suse.com>
Depmod fails for a kernel made with:
make allnoconfig
echo -e "CONFIG_MODULES=y\nCONFIG_SERIAL_8250=m\nCONFIG_SERIAL_8250_EXTENDED=y\nCONFIG_SERIAL_8250_RSA=y" >> .config
make olddefconfig
...due to a dependency loop:
depmod: ERROR: Cycle detected: 8250 -> 8250_base -> 8250
depmod: ERROR: Found 2 modules in dependency cycles!
This is caused by the move of 8250 RSA code from 8250_port.c (in
8250_base.ko) into 8250_rsa.c (in 8250.ko) by the commit 5a128fb475
("serial: 8250: move RSA functions to 8250_rsa.c"). The commit
b20d6576cd ("serial: 8250: export RSA functions") tried to fix a
missing symbol issue with EXPORTs but those then cause this dependency
cycle.
Break dependency loop by moving 8250_rsa.o from 8250.ko to 8250_base.ko
and by passing univ8250_port_base_ops to univ8250_rsa_support() that
can make a local copy of it.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: Alex Davis <alex47794@gmail.com>
Fixes: 5a128fb475 ("serial: 8250: move RSA functions to 8250_rsa.c")
Fixes: b20d6576cd ("serial: 8250: export RSA functions")
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/all/87frc3sd8d.fsf@posteo.net/
Link: https://lore.kernel.org/all/CADiockCvM6v+d+UoFZpJSMoLAdpy99_h-hJdzUsdfaWGn3W7-g@mail.gmail.com/
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://patch.msgid.link/20251110105043.4062-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On RSCI IP, a deadlock occurs during a FIFO overrun error, as it uses a
different register to clear the FIFO overrun error status.
Cc: stable@kernel.org
Fixes: 0666e3fe95 ("serial: sh-sci: Add support for RZ/T2H SCI")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251114101350.106699-3-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the driver for on-chip UART used on Loongson family chips.
The hardware is similar to NS16550A, but there are the following
differences:
- Some chips (such as Loongson-2K2000) have added a fractional division
register to obtain the required baud rate accurately, so the
{get,set}_divisor callback is overridden.
- Due to hardware defects, quirk handling is required for
UART_MCR/UART_MSR.
Co-developed-by: Haowei Zheng <zhenghaowei@loongson.cn>
Signed-off-by: Haowei Zheng <zhenghaowei@loongson.cn>
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Reviewed-by: Huacai Chen <chenhuacai@loongson.cn>
Link: https://patch.msgid.link/2c2a01a276b9250efea0c7aa190efecdfd6fdf5a.1760166651.git.zhoubinbin@loongson.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The KEBA UART is found in the system FPGA of KEBA PLC devices. It is
mostly 8250 compatible with extension for some UART modes.
3 different variants exist. The simpliest variant supports only RS-232
and is used for debug interfaces. The next variant supports only RS-485
and is used mostly for communication with KEBA panel devices. The third
variant is able to support RS-232, RS-485 and RS-422. For this variant
not only the mode of the UART is configured, also the physics and
transceivers are switched according to the mode.
Signed-off-by: Gerhard Engleder <eg@keba.com>
Tested-by: Daniel Gierlinger <gida@keba.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Link: https://patch.msgid.link/20251023151229.11774-3-gerhard@engleder-embedded.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit fe7f0fa43c ("serial: 8250: Support rs485 devicetree properties")
retrieves rs485 properties for 8250 drivers. These properties are read
from the firmware node of the device within uart_get_rs485_mode(). If the
firmware node does not exist, then the rs485 flags are still reset. Thus,
8250 driver cannot set rs485 flags to enable a defined rs485 mode during
driver loading. This is no problem so far, as no 8250 driver sets the
rs485 flags.
The default rs485 mode can also be set by firmware nodes. But for some
devices a firmware node does not exist. E.g., for a PCIe based serial
interface on x86 no device tree is available and the ACPI information of
the BIOS often cannot by modified. In this case it shall be possible,
that a driver works out of the box by setting a reasonable default rs485
mode.
If no firmware node exists, then it should be possible for the driver to
set a reasonable default rs485 mode. Therefore, reset rs485 flags only
if a firmware node exists.
Signed-off-by: Gerhard Engleder <eg@keba.com>
Cc: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Link: https://patch.msgid.link/20251023151229.11774-2-gerhard@engleder-embedded.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Qualcomm automotive SA8255p SoC relies on firmware to configure
platform resources, including clocks, interconnects and TLMM.
The driver requests resources operations over SCMI using power
and performance protocols.
The SCMI power protocol enables or disables resources like clocks,
interconnect paths, and TLMM (GPIOs) using runtime PM framework APIs,
such as resume/suspend, to control power states(on/off).
The SCMI performance protocol manages UART baud rates, with each baud
rate represented by a performance level. The driver uses the
dev_pm_opp_set_level() API to request the desired baud rate by
specifying the performance level.
Signed-off-by: Praveen Talari <praveen.talari@oss.qualcomm.com>
Link: https://patch.msgid.link/20251110101043.2108414-5-praveen.talari@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The GENI serial driver currently handles power resource management
through calls to the statically defined geni_serial_resources_on() and
geni_serial_resources_off() functions. This approach reduces modularity
and limits support for platforms with diverse power management
mechanisms, including resource managed by firmware.
Improve modularity and enable better integration with platform-specific
power management, introduce support for runtime PM. Use
pm_runtime_resume_and_get() and pm_runtime_put_sync() within the
qcom_geni_serial_pm() callback to control resource power state
transitions based on UART power state changes.
Signed-off-by: Praveen Talari <praveen.talari@oss.qualcomm.com>
Link: https://patch.msgid.link/20251110101043.2108414-4-praveen.talari@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In sprd_clk_init(), when devm_clk_get() returns -EPROBE_DEFER
for either uart or source clock, we should propagate the
error instead of just warning and continuing with NULL clocks.
Currently the driver only emits a warning when clock acquisition
fails and proceeds with NULL clock pointers. This can lead to
issues later when the clocks are actually needed. More importantly,
when the clock provider is not ready yet and returns -EPROBE_DEFER,
we should return this error to allow deferred probing.
This change adds explicit checks for -EPROBE_DEFER after both:
1. devm_clk_get(uport->dev, uart)
2. devm_clk_get(uport->dev, source)
When -EPROBE_DEFER is encountered, the function now returns
-EPROBE_DEFER to let the driver framework retry probing
later when the clock dependencies are resolved.
Signed-off-by: Wenhua Lin <Wenhua.Lin@unisoc.com>
Link: https://patch.msgid.link/20251022030840.956589-1-Wenhua.Lin@unisoc.com
Reviewed-by: Cixi Geng <cixi.geng@linux.dev>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It makes it possible to use just "earlycon" param in kernel cmdline
on Exynos850 based boards instead of "earlycon=exynos4210,0x13820000",
as described in [1]:
When used with no options, the early console is determined by
stdout-path property in device tree's chosen node
[1] Documentation/admin-guide/kernel-parameters.txt
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://patch.msgid.link/20251118024822.28148-1-semen.protsenko@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
icom_probe() uses pci_read_config_dword() that returns PCIBIOS_*
codes. The return code is returned from the probe function as is but
probe functions should return normal errnos. A proper implementation
can be found in drivers/leds/leds-ss4200.c
Convert PCIBIOS_* return codes using pcibios_err_to_errno() into
normal errno before returning them.
Signed-off-by: Haotian Zhang <vulab@iscas.ac.cn>
Link: https://patch.msgid.link/20251117040710.1544-1-vulab@iscas.ac.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch resolves the warning "sizeof *port should be sizeof(*port)"
detected by checkpatch.pl.
Signed-off-by: jempty.liang <imntjempty@163.com>
Link: https://patch.msgid.link/20251117034117.55588-1-imntjempty@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Addi-Data GmbH is manufacturing multi-serial ports cards supporting CompactPCI (known as CPCI).
Those cards are identified with different DeviceIds. Those cards integrating standard UARTs
work the same way as PCI/PCIe models already supported in the serial driver.
Signed-off-by: Magne Bruno <magne.bruno@addi-data.com>
Link: https://patch.msgid.link/20251110162456.341029-1-magne.bruno@addi-data.com
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The validator is not happy:
Warning: drivers/tty/serial/mux.c:351 expecting prototype for mux_drv_poll(). Prototype was for mux_poll() instead
Update the kernel-doc accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20251106113815.2302539-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently if a user enqueue a work item using schedule_delayed_work() the
used wq is "system_wq" (per-cpu wq) while queue_delayed_work() use
WORK_CPU_UNBOUND (used when a cpu is not specified). The same applies to
schedule_work() that is using system_wq and queue_work(), that makes use
again of WORK_CPU_UNBOUND.
This lack of consistentcy cannot be addressed without refactoring the API.
This patch continues the effort to refactor worqueue APIs, which has begun
with the change introducing new workqueues and a new alloc_workqueue flag:
commit 128ea9f6cc ("workqueue: Add system_percpu_wq and system_dfl_wq")
commit 930c2ea566 ("workqueue: Add new WQ_PERCPU flag")
system_dfl_wq should be the default workqueue so as not to enforce
locality constraints for random work whenever it's not required.
The old system_unbound_wq will be kept for a few release cycles.
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Marco Crivellari <marco.crivellari@suse.com>
Link: https://patch.msgid.link/20251104105446.110884-1-marco.crivellari@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In 2009, commit c82f63e411 ("PCI: check saved state before restore")
changed the behavior of pci_restore_state() such that it became necessary
to call pci_save_state() afterwards, lest recovery from subsequent PCI
errors fails.
The commit has just been reverted and so all the pci_save_state() after
pci_restore_state() calls that have accumulated in the tree are now
superfluous. Drop them.
Two drivers chose a different approach to achieve the same result:
drivers/scsi/ipr.c and drivers/net/ethernet/intel/e1000e/netdev.c set the
pci_dev's "state_saved" flag to true before calling pci_restore_state().
Drop this as well.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com> # qat
Link: https://patch.msgid.link/c2b28cc4defa1b743cf1dedee23c455be98b397a.1760274044.git.lukas@wunner.de
IRQF_SHARED is the only flag handled in __serial8250_isa_init_ports()
and serial8250_probe_platform(). There is no need to precompute the
flags. Instead, initialize port->irqflags directly in the for loop.
Note the "if (bool)" is cheap and these are not hot paths anyway.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://patch.msgid.link/20251119092457.826789-7-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
8250_core is the only place where skip_txen_test is used. And platform
and core end up in 8250.ko, so there is no change in module name (param
prefix). Therefore, move skip_txen_test there and make it local.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://patch.msgid.link/20251119092457.826789-5-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In 3.7, 8250 was unintentionally renamed to 8250_core. This happened in
the commit 835d844d1a (8250_pnp: do pnp probe before legacy probe).
This made 8250.<xxxx> module options effectively defunct. Instead,
8250_core.<xxxx> worked.
In 3.9, the commit f2b8dfd9e4 (serial: 8250: Keep 8250.<xxxx> module
options functional after driver rename) made the original options work
again by introducing a hack.
Later in 3.9, the commit 9196d8acd7 (TTY: 8250, revert module name
change) changed the module name back to 8250 (from 8250_core). Since
then, the hack was there to support the transient 8250_core.<xxxx>
options. Those were present only in the 3.7..3.9 range.
These transient options were deprecated by 9326b047e4 (TTY: 8250,
deprecated 8250_core.* options) in v3.9 too.
Now, after those 12 years, it is time to get rid of this hack
completely.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://patch.msgid.link/20251119092457.826789-4-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Provided the uart driver is available globally, there is no need to
store a pointer to it in struct cdns_uart. Instead, use the global
cdns_uart_uart_driver in the code directly.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Link: https://patch.msgid.link/20251119092457.826789-3-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use guards in the serial_core code. This improves readability, makes
error handling easier, and marks locked portions of code explicit. All
that while being sure the lock is unlocked.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://patch.msgid.link/20251119100140.830761-11-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Neither uart_do_autoconfig(), nor uart_wait_modem_status() can return
-ENOIOCTLCMD. The ENOIOCTLCMD checks are there to check if 'cmd' matched
against TIOCSERCONFIG, and TIOCMIWAIT respectively. (With 0 or error in
'ret', it does not matter.)
Therefore, the code can simply return from the TIOCSERCONFIG and
TIOCMIWAIT spots immediately.
To be more explicit, use 'if' instead of switch-case for those single
values.
And return without jumping to the 'out' label -- it can be removed too.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://patch.msgid.link/20251119100140.830761-10-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use guards in the vt/keyboard code. This improves readability, makes
error handling easier, and marks locked portions of code explicit. All
that while being sure the lock is unlocked.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://patch.msgid.link/20251119100140.830761-9-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Return immediately when something goes wrong in vt_do_kbkeycode_ioctl().
This makes the code flow more obvious.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://patch.msgid.link/20251119100140.830761-8-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The vt/keyboard code can use __free to ensure the temporary buffers are
freed. Perform the switch.
And even one non-temporary in kbd_connect(). There are fail paths, so
ensure the buffer is freed in them and not when returning 0 -- by
retain_and_null_ptr().
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://patch.msgid.link/20251119100140.830761-7-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use guards in the moxa code. This improves readability, makes error
handling easier, and marks locked portions of code explicit. All that
while being sure the lock is unlocked.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://patch.msgid.link/20251119100140.830761-6-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use guards in the n_hdlc code. This improves readability, makes error
handling easier, and marks locked portions of code explicit. All that
while being sure the lock is unlocked.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://patch.msgid.link/20251119100140.830761-5-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The cases in the switch() of n_hdlc_tty_ioctl() can return immediately
-- no need to store into error and return later.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://patch.msgid.link/20251119100140.830761-4-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use guards in the n_tty code. This improves readability, makes error
handling easier, and marks locked portions of code explicit. All that
while being sure the lock is unlocked.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://patch.msgid.link/20251119100140.830761-3-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use guards in the pty code. This improves readability, makes error
handling easier, and marks locked portions of code explicit. All that
while being sure the lock is unlocked.
pty_set_pktmode() is handled specially -- the conditions are inverted
and return called if conditions unmet. This avoid double nested 'if's.
The variable is renamed to want_pktmode so it is not confused with the
current state of pktmode.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://patch.msgid.link/20251119100140.830761-2-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The row/column bounds (for a screen window box) are changed from
'offset one' to 'offset zero' and bound to the screen size using:
v->xs = min_t(u16, v->xs - 1, vc->vc_cols - 1);
This has the side effect of converting zero to the limit.
A check I'm adding to min_t() reports that (u16)(v->xs - 1) (etc)
discards signiticant bits (because v->xs is promoted to 'int' before
the addition).
If v->xs is zero (it comes from userspace) it converts -1 to 0xffff.
This is then bounded to 'vc->vc_cols - 1' which will be fine.
Replace with:
v->xs = umin(v->xs - 1, vc->vc_cols - 1);
which again converts a -1 to unsigned - this time to 0xffffffff,
with the same overall effect.
Whether zero is meant to mean the 'maximum size' is unknown.
I can't find any documentation for the ioctl and it pre-dates git.
Detected by an extra check added to min_t().
Signed-off-by: David Laight <david.laight.linux@gmail.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://patch.msgid.link/20251119224140.8616-28-david.laight.linux@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When compiled with -ffunction-sections (e.g., for LTO, livepatch, dead
code elimination, AutoFDO, or Propeller), the startup() function gets
compiled into the .text.startup section (or in some cases
.text.startup.constprop.0 or .text.startup.isra.0).
However, the .text.startup and .text.startup.* sections are also used by
the compiler for __attribute__((constructor)) code.
This naming conflict causes the vmlinux linker script to wrongly place
startup() function code in .init.text, which gets freed during boot.
Some builds have a mix of objects, both with and without
-ffunctions-sections, so it's not possible for the linker script to
disambiguate with #ifdef CONFIG_FUNCTION_SECTIONS or similar. This
means that "startup" unfortunately needs to be prohibited as a function
name.
Rename startup() to startup_hw(). For consistency, also rename its
shutdown() counterpart to shutdown_hw().
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://patch.msgid.link/f0ee750f35c878172cc09916a0724b74e62eadc2.1763669451.git.jpoimboe@kernel.org
When compiled with -ffunction-sections (e.g., for LTO, livepatch, dead
code elimination, AutoFDO, or Propeller), the startup() function gets
compiled into the .text.startup section (or in some cases
.text.startup.constprop.0 or .text.startup.isra.0).
However, the .text.startup and .text.startup.* sections are also used by
the compiler for __attribute__((constructor)) code.
This naming conflict causes the vmlinux linker script to wrongly place
startup() function code in .init.text, which gets freed during boot.
Some builds have a mix of objects, both with and without
-ffunctions-sections, so it's not possible for the linker script to
disambiguate with #ifdef CONFIG_FUNCTION_SECTIONS or similar. This
means that "startup" unfortunately needs to be prohibited as a function
name.
Rename startup() to rs_startup(). For consistency, also rename its
shutdown() counterpart to rs_shutdown().
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://patch.msgid.link/9e56afff5268b0b12b99a8aa9bf244d6ebdcdf47.1763669451.git.jpoimboe@kernel.org
When compiled with -ffunction-sections (e.g., for LTO, livepatch, dead
code elimination, AutoFDO, or Propeller), the startup() function gets
compiled into the .text.startup section (or in some cases
.text.startup.constprop.0 or .text.startup.isra.0).
However, the .text.startup and .text.startup.* sections are also used by
the compiler for __attribute__((constructor)) code.
This naming conflict causes the vmlinux linker script to wrongly place
startup() function code in .init.text, which gets freed during boot.
Some builds have a mix of objects, both with and without
-ffunctions-sections, so it's not possible for the linker script to
disambiguate with #ifdef CONFIG_FUNCTION_SECTIONS or similar. This
means that "startup" unfortunately needs to be prohibited as a function
name.
Rename startup() to icom_startup(). For consistency, also rename its
shutdown() counterpart to icom_shutdown().
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://patch.msgid.link/1aee9ef69f9d40405676712b34f0c397706e7023.1763669451.git.jpoimboe@kernel.org
Inline the contents of sh-sci.h into sh-sci.c and remove the
header file. The header only contained register definitions
and macros used exclusively by the sh-sci driver, making the
separate header unnecessary.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://patch.msgid.link/20251023104313.210989-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check for returned DMA addresses using specialized dma_mapping_error()
helper which is generally recommended for this purpose by
Documentation/core-api/dma-api.rst:
"In some circumstances dma_map_single(), ...
will fail to create a mapping. A driver can check for these errors
by testing the returned DMA address with dma_mapping_error()."
Found via static analysis and this is similar to commit fa0308134d
("ALSA: memalloc: prefer dma_mapping_error() over explicit address checking")
Fixes: 58ac1b3799 ("ARM: PL011: Fix DMA support")
Cc: stable <stable@kernel.org>
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://patch.msgid.link/20251027092053.87937-1-linmq006@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Indicate why lock needs to be asserted when accessing
MSR register, as this is not immediately obvious when looking at this
register in the device datasheet.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20251027142957.1032073-15-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fold some multi-line comments into a single line, taking advantage of the
new 100 line length limit to improve readability and to have uniform style
across driver.
Add missing 's' to SC16IS7XX_MCR_TCRTLR_BIT registers comments.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20251027142957.1032073-14-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to redefine the driver name. Use KBUILD_MODNAME and get
rid of DRV_NAME altogether.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20251027142957.1032073-12-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify macro to_sc16is7xx_one() to only take one parameter, as most
of the time (19) it is called with the "port" structure name. This
improves readability.
For the remaining places where it is called (4), simply use container_of()
locally. This is similar to what is done in other drivers (ex: max310x).
For sc16is7xx_tx_proc(), first assigning "one" variable allows to simplify
"port" variable init.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20251027142957.1032073-10-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sc16is7xx_probe() function is very long. To improve readability, move
port/channel initialization to a separate function.
No functional change intended.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20251027142957.1032073-9-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SPR shares the same address space as TLR and XOFF2. If SPR or TLR were to
be used eventually, this could lead to incorrect read value from the cache.
Prevent this potential bug by declaring SPR/TLR/XOFF2 as volatile.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20251027142957.1032073-8-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Core already prints detailed error messages on ENOMEM errors and drivers
should avoid repeating it.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20251027142957.1032073-7-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Guards can help to make the code more readable, so use them wherever they
do so.
In sc16is7xx_port_irq(), labels and 'rc' locals are eliminated completely.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20251027142957.1032073-6-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to cast from a void * pointer, so remove this cast.
Also remove empty line inavertently added in commit d5078509c8
("serial: sc16is7xx: improve do/while loop in sc16is7xx_irq()") and
change variables order to follow reversed xmas tree.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20251027142957.1032073-5-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rename lock/unlock functions to make it more generic and applicable to both
the Enhanced register set and the Special register set.
Use this new generic function when accessing the Special register set in
sc16is7xx_set_baud(), and when accessing the Enhanced register set in
sc16is7xx_set_termios() and sc16is7xx_probe().
This helps readability and also avoid to make future mistakes when
accessing these obfuscated registers.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20251027142957.1032073-4-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This mutex is used as a lock when accessing registers that share the same
address space, not necessarily EFR registers.
For example, address 0x06 is shared by MSR, TCR and XOFF1 registers,
independently of EFR.
Rename the mutex with a more generic name to avoid misinterpreting its
usage.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20251027142957.1032073-3-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no reference to CONF_MODE_A or CONF_MODE_B in the manufacturer's
datasheet.
Rename register set configuration macros for the LCR register, to better
show their intended usage to select either the Special register set, or the
Enhanced register set.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20251027142957.1032073-2-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add missing kernel-doc entry for the @dlci parameter in
gsm_modem_send_initial_msc(), which fixes the following warning
reported by kernel-doc:
Warning: drivers/tty/n_gsm.c:4175 function parameter 'dlci' not described in 'gsm_modem_send_initial_msc'
Signed-off-by: Kriish Sharma <kriish.sharma2006@gmail.com>
Link: https://patch.msgid.link/20251025161206.795784-1-kriish.sharma2006@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some MediaTek SoCs got a gated UART baud clock, which currently gets
disabled as the clk subsystem believes it would be unused. This results in
the uart freezing right after "clk: Disabling unused clocks" on those
platforms.
Request the baud clock to be prepared and enabled during probe, and to
restore run-time power management capabilities to what it was before commit
e32a83c70c ("serial: 8250-mtk: modify mtk uart power and clock
management") disable and unprepare the baud clock when suspending the UART,
prepare and enable it again when resuming it.
Fixes: e32a83c70c ("serial: 8250-mtk: modify mtk uart power and clock management")
Fixes: b6c7ff2693 ("serial: 8250_mtk: Simplify clock sequencing and runtime PM")
Cc: stable <stable@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://patch.msgid.link/de5197ccc31e1dab0965cabcc11ca92e67246cf6.1758058441.git.daniel@makrotopia.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check the return value of reset_control_deassert() in the probe
function to prevent continuing probe when reset deassertion fails.
Previously, reset_control_deassert() was called without checking its
return value, which could lead to probe continuing even when the
device reset wasn't properly deasserted.
The fix checks the return value and returns an error with dev_err_probe()
if reset deassertion fails, providing better error handling and
diagnostics.
Fixes: acbdad8dd1 ("serial: 8250_dw: simplify optional reset handling")
Cc: stable <stable@kernel.org>
Signed-off-by: Artem Shimko <a.shimko.dev@gmail.com>
Link: https://patch.msgid.link/20251019095131.252848-1-a.shimko.dev@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 43c51bb573 ("sc16is7xx: make sure device is in suspend once
probed") permanently enabled access to the enhanced features in
sc16is7xx_probe(), and it is never disabled after that.
Therefore, remove re-enable of enhanced features in
sc16is7xx_set_baud(). This eliminates a potential useless read + write
cycle each time the baud rate is reconfigured.
Fixes: 43c51bb573 ("sc16is7xx: make sure device is in suspend once probed")
Cc: stable <stable@kernel.org>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20251006142002.177475-1-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Advantech 2-port serial card with PCI vendor=0x13fe and device=0x0018
has a 'XR17V35X' chip installed on the circuit board. Therefore, this
driver can be used instead of theu outdated out-of-tree driver from the
manufacturer.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Cc: stable <stable@kernel.org>
Link: https://patch.msgid.link/20250924134115.2667650-1-fe@dev.tdt.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The receive error handling code is shared between RSCI and all other
SCIF port types, but the RSCI overrun_reg is specified as a memory
offset, while for other SCIF types it is an enum value used to index
into the sci_port_params->regs array, as mentioned above the
sci_serial_in() function.
For RSCI, the overrun_reg is CSR (0x48), causing the sci_getreg() call
inside the sci_handle_fifo_overrun() function to index outside the
bounds of the regs array, which currently has a size of 20, as specified
by SCI_NR_REGS.
Because of this, we end up accessing memory outside of RSCI's
rsci_port_params structure, which, when interpreted as a plat_sci_reg,
happens to have a non-zero size, causing the following WARN when
sci_serial_in() is called, as the accidental size does not match the
supported register sizes.
The existence of the overrun_reg needs to be checked because
SCIx_SH3_SCIF_REGTYPE has overrun_reg set to SCLSR, but SCLSR is not
present in the regs array.
Avoid calling sci_getreg() for port types which don't use standard
register handling.
Use the ops->read_reg() and ops->write_reg() functions to properly read
and write registers for RSCI, and change the type of the status variable
to accommodate the 32-bit CSR register.
sci_getreg() and sci_serial_in() are also called with overrun_reg in the
sci_mpxed_interrupt() interrupt handler, but that code path is not used
for RSCI, as it does not have a muxed interrupt.
------------[ cut here ]------------
Invalid register access
WARNING: CPU: 0 PID: 0 at drivers/tty/serial/sh-sci.c:522 sci_serial_in+0x38/0xac
Modules linked in: renesas_usbhs at24 rzt2h_adc industrialio_adc sha256 cfg80211 bluetooth ecdh_generic ecc rfkill fuse drm backlight ipv6
CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted 6.17.0-rc1+ #30 PREEMPT
Hardware name: Renesas RZ/T2H EVK Board based on r9a09g077m44 (DT)
pstate: 604000c5 (nZCv daIF +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : sci_serial_in+0x38/0xac
lr : sci_serial_in+0x38/0xac
sp : ffff800080003e80
x29: ffff800080003e80 x28: ffff800082195b80 x27: 000000000000000d
x26: ffff8000821956d0 x25: 0000000000000000 x24: ffff800082195b80
x23: ffff000180e0d800 x22: 0000000000000010 x21: 0000000000000000
x20: 0000000000000010 x19: ffff000180e72000 x18: 000000000000000a
x17: ffff8002bcee7000 x16: ffff800080000000 x15: 0720072007200720
x14: 0720072007200720 x13: 0720072007200720 x12: 0720072007200720
x11: 0000000000000058 x10: 0000000000000018 x9 : ffff8000821a6a48
x8 : 0000000000057fa8 x7 : 0000000000000406 x6 : ffff8000821fea48
x5 : ffff00033ef88408 x4 : ffff8002bcee7000 x3 : ffff800082195b80
x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffff800082195b80
Call trace:
sci_serial_in+0x38/0xac (P)
sci_handle_fifo_overrun.isra.0+0x70/0x134
sci_er_interrupt+0x50/0x39c
__handle_irq_event_percpu+0x48/0x140
handle_irq_event+0x44/0xb0
handle_fasteoi_irq+0xf4/0x1a0
handle_irq_desc+0x34/0x58
generic_handle_domain_irq+0x1c/0x28
gic_handle_irq+0x4c/0x140
call_on_irq_stack+0x30/0x48
do_interrupt_handler+0x80/0x84
el1_interrupt+0x34/0x68
el1h_64_irq_handler+0x18/0x24
el1h_64_irq+0x6c/0x70
default_idle_call+0x28/0x58 (P)
do_idle+0x1f8/0x250
cpu_startup_entry+0x34/0x3c
rest_init+0xd8/0xe0
console_on_rootfs+0x0/0x6c
__primary_switched+0x88/0x90
---[ end trace 0000000000000000 ]---
Cc: stable <stable@kernel.org>
Fixes: 0666e3fe95 ("serial: sh-sci: Add support for RZ/T2H SCI")
Signed-off-by: Cosmin Tanislav <cosmin-gabriel.tanislav.xa@renesas.com>
Link: https://patch.msgid.link/20250923154707.1089900-1-cosmin-gabriel.tanislav.xa@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the '8250_exar' module is loaded into the kernel, a kernel trace
with 'WARN_ON(legacy_iomap_table[bar])' is dumped to the console,
because the old pci table mapping is still used in '8250_pcilib'.
The old function have been deprecated in commit e354bb84a4 ("PCI:
Deprecate pcim_iomap_table(), pcim_iomap_regions_request_all()").
The remapping already takes or must take place in the driver that calls
the function 'serial8250_pci_setup_port()'. The remapping should only be
called once via 'pcim_iomap()'. Therefore the remapping moved to the
caller of 'serial8250_pci_setup_port()'.
To replace the outdated/legacy iomap_table processing in '8250_pcilib' the
function signature of 'serial8250_pci_setup_port()' has been extended with
an already iomapped address value. So this can be used directly without
io mapping again.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://patch.msgid.link/20250930072743.791580-1-fe@dev.tdt.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current imx uart wakeup event would not report itself as wakeup source
through sysfs. Add pm_wakeup_event() to support it.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20251002045259.2725461-3-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the i.MX UART driver enables wake-related registers for all
UART devices by default. However, this is unnecessary for devices that
are not configured as wakeup sources. To address this, add a
device_may_wakeup() check before configuring the UART wake-related
registers.
Fixes: db1a9b5500 ("tty: serial: imx: Allow UART to be a source for wakeup")
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20251002045259.2725461-2-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current lpuart wakeup event would not report itself as wakeup source
through sysfs. Add pm_wakeup_event() to support it.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20250924025607.2515833-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is a single driver fix for the qcom_geni_serial driver for
6.18-rc1. It has been in my tree for weeks, but missed being sent to
you for 6.17-final due to travel on my side.
This fixes a reported regression for this driver that prevents 6.17 from
working properly on this platform.
It has been in linux-next for many weeks with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCaOUQrA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymmXwCgj5hLg2MHRlvZ+aCD0K/S2Qt4eqEAn32POqfZ
UntJ9O23oHW1+RmAvBB7
=zKb3
-----END PGP SIGNATURE-----
Merge tag 'tty-6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty driver fix from Greg KH:
"Here is a single driver fix for the qcom_geni_serial driver. It has
been in my tree for weeks, but missed being sent to you for 6.17-final
due to travel on my side.
This fixes a reported regression for this driver that prevents 6.17
from working properly on this platform.
It has been in linux-next for many weeks with no reported issues"
* tag 'tty-6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: qcom-geni: Fix blocked task
Here are some small updates for tty/serial drivers for 6.18-rc1.
Not many changes overall, just the usual:
- abi cleanups and reworking of the tty functions by Jiri by adding
console lock guard logic
- 8250_platform driver updates
- qcom-geni driver updates
- other minor serial driver updates
- some more vt escape codes added
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCaOEnLA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymLswCfa2SDyet0vn5oIrto+0WG9Wxlp3AAoMaDzkqG
DX2YoOI1L0miAQfQ9IhZ
=0V8V
-----END PGP SIGNATURE-----
Merge tag 'tty-6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here are some small updates for tty/serial drivers for 6.18-rc1.
Not many changes overall, just the usual:
- abi cleanups and reworking of the tty functions by Jiri by adding
console lock guard logic
- 8250_platform driver updates
- qcom-geni driver updates
- other minor serial driver updates
- some more vt escape codes added
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (43 commits)
tty: serial: fix help message for SERIAL_CPM
serial: 8250: omap: Support wakeup pinctrl state on suspend
dt-bindings: serial: 8250_omap: Add wakeup pinctrl state
serial: max310x: improve interrupt handling
vt: move vc_saved_screen to within tty allocated judgment
Revert "m68k: make HPDCA and HPAPCI bools"
tty: remove redundant condition checks
tty/vt: Add missing return value for VT_RESIZE in vt_ioctl()
vt: remove redundant check on vc_mode in con_font_set()
serial: qcom-geni: Add DFS clock mode support to GENI UART driver
m68k: make HPDCA and HPAPCI bools
tty: n_gsm: Don't block input queue by waiting MSC
serial: qcom-geni: Fix off-by-one error in ida_alloc_range()
serdev: Drop dev_pm_domain_detach() call
serial: sc16is7xx: drop redundant conversion to bool
vt: add support for smput/rmput escape codes
serial: stm32: allow selecting console when the driver is module
serial: 8250_core: fix coding style issue
tty: serial: Modify the use of dev_err_probe()
s390/char/con3270: use tty_port_tty guard()
...
Lots of platform specific updates for Qualcomm SoCs, including a
new TEE subsystem driver for the Qualcomm QTEE firmware interface.
Added support for the Apple A11 SoC in drivers that are shared with the
M1/M2 series, among more updates for those.
Smaller platform specific driver updates for Renesas, ASpeed, Broadcom,
Nvidia, Mediatek, Amlogic, TI, Allwinner, and Freescale SoCs.
Driver updates in the cache controller, memory controller and reset
controller subsystems.
SCMI firmware updates to add more features and improve robustness.
This includes support for having multiple SCMI providers in a single
system.
TEE subsystem support for protected DMA-bufs, allowing hardware to
access memory areas that managed by the kernel but remain inaccessible
from the CPU in EL1/EL0.
-----BEGIN PGP SIGNATURE-----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=mcZR
-----END PGP SIGNATURE-----
Merge tag 'soc-drivers-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC driver updates from Arnd Bergmann:
"Lots of platform specific updates for Qualcomm SoCs, including a new
TEE subsystem driver for the Qualcomm QTEE firmware interface.
Added support for the Apple A11 SoC in drivers that are shared with
the M1/M2 series, among more updates for those.
Smaller platform specific driver updates for Renesas, ASpeed,
Broadcom, Nvidia, Mediatek, Amlogic, TI, Allwinner, and Freescale
SoCs.
Driver updates in the cache controller, memory controller and reset
controller subsystems.
SCMI firmware updates to add more features and improve robustness.
This includes support for having multiple SCMI providers in a single
system.
TEE subsystem support for protected DMA-bufs, allowing hardware to
access memory areas that managed by the kernel but remain inaccessible
from the CPU in EL1/EL0"
* tag 'soc-drivers-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (139 commits)
soc/fsl/qbman: Use for_each_online_cpu() instead of for_each_cpu()
soc: fsl: qe: Drop legacy-of-mm-gpiochip.h header from GPIO driver
soc: fsl: qe: Change GPIO driver to a proper platform driver
tee: fix register_shm_helper()
pmdomain: apple: Add "apple,t8103-pmgr-pwrstate"
dt-bindings: spmi: Add Apple A11 and T2 compatible
serial: qcom-geni: Load UART qup Firmware from linux side
spi: geni-qcom: Load spi qup Firmware from linux side
i2c: qcom-geni: Load i2c qup Firmware from linux side
soc: qcom: geni-se: Add support to load QUP SE Firmware via Linux subsystem
soc: qcom: geni-se: Cleanup register defines and update copyright
dt-bindings: qcom: se-common: Add QUP Peripheral-specific properties for I2C, SPI, and SERIAL bus
Documentation: tee: Add Qualcomm TEE driver
tee: qcom: enable TEE_IOC_SHM_ALLOC ioctl
tee: qcom: add primordial object
tee: add Qualcomm TEE driver
tee: increase TEE_MAX_ARG_SIZE to 4096
tee: add TEE_IOCTL_PARAM_ATTR_TYPE_OBJREF
tee: add TEE_IOCTL_PARAM_ATTR_TYPE_UBUF
tee: add close_context to TEE driver operation
...
Introduce support for loading firmware into the QUP serial engines from
Linux, which allows deferring selection of which protocol (uart, i2c,
spi, etc) a given SE should have until the OS loads.
Also introduce the "object invoke" interface in the SCM driver, to
provide interface to the Qualcomm TEE driver.
-----BEGIN PGP SIGNATURE-----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=TulG
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=JuVO
-----END PGP SIGNATURE-----
Merge tag 'qcom-drivers-for-6.18-2' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into soc/drivers
More Qualcomm device driver updates for v6.18
Introduce support for loading firmware into the QUP serial engines from
Linux, which allows deferring selection of which protocol (uart, i2c,
spi, etc) a given SE should have until the OS loads.
Also introduce the "object invoke" interface in the SCM driver, to
provide interface to the Qualcomm TEE driver.
* tag 'qcom-drivers-for-6.18-2' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
serial: qcom-geni: Load UART qup Firmware from linux side
spi: geni-qcom: Load spi qup Firmware from linux side
i2c: qcom-geni: Load i2c qup Firmware from linux side
soc: qcom: geni-se: Add support to load QUP SE Firmware via Linux subsystem
soc: qcom: geni-se: Cleanup register defines and update copyright
dt-bindings: qcom: se-common: Add QUP Peripheral-specific properties for I2C, SPI, and SERIAL bus
firmware: qcom: scm: add support for object invocation
firmware: qcom: tzmem: export shm_bridge create/delete
Link: https://lore.kernel.org/r/20250921020225.595403-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add provision to load firmware of Serial engine for UART protocol from
Linux Execution Environment on running on APPS processor.
Co-developed-by: Mukesh Kumar Savaliya <mukesh.savaliya@oss.qualcomm.com>
Signed-off-by: Mukesh Kumar Savaliya <mukesh.savaliya@oss.qualcomm.com>
Signed-off-by: Viken Dadhaniya <viken.dadhaniya@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250911043256.3523057-7-viken.dadhaniya@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Revert commit 1afa70632c ("serial: qcom-geni: Enable PM runtime for
serial driver") and its dependent commit 86fa39dd6f ("serial:
qcom-geni: Enable Serial on SA8255p Qualcomm platforms") because the
first one causes regression - hang task on Qualcomm RB1 board (QRB2210)
and unable to use serial at all during normal boot:
INFO: task kworker/u16:0:12 blocked for more than 42 seconds.
Not tainted 6.17.0-rc1-00004-g53e760d89498 #9
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:kworker/u16:0 state:D stack:0 pid:12 tgid:12 ppid:2 task_flags:0x4208060 flags:0x00000010
Workqueue: async async_run_entry_fn
Call trace:
__switch_to+0xe8/0x1a0 (T)
__schedule+0x290/0x7c0
schedule+0x34/0x118
rpm_resume+0x14c/0x66c
rpm_resume+0x2a4/0x66c
rpm_resume+0x2a4/0x66c
rpm_resume+0x2a4/0x66c
__pm_runtime_resume+0x50/0x9c
__driver_probe_device+0x58/0x120
driver_probe_device+0x3c/0x154
__driver_attach_async_helper+0x4c/0xc0
async_run_entry_fn+0x34/0xe0
process_one_work+0x148/0x290
worker_thread+0x2c4/0x3e0
kthread+0x118/0x1c0
ret_from_fork+0x10/0x20
The issue was reported on 12th of August and was ignored by author of
commits introducing issue for two weeks. Only after complaining author
produced a fix which did not work, so if original commits cannot be
reliably fixed for 5 weeks, they obviously are buggy and need to be
dropped.
Fixes: 1afa70632c ("serial: qcom-geni: Enable PM runtime for serial driver")
Reported-by: Alexey Klimov <alexey.klimov@linaro.org>
Closes: https://lore.kernel.org/all/DC0D53ZTNOBU.E8LSD5E5Z8TX@linaro.org/
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Alexey Klimov <alexey.klimov@linaro.org>
Reviewed-by: Alexey Klimov <alexey.klimov@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20250917010437.129912-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Running checkpatch reported error extra whitespace at the
end of help message for SERIAL_CPM menu entry
Signed-off-by: Arturs Artamonovs <Arturs.Artamonovs@analog.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This update includes:
- basic infrastructure support for Microchip LAN969x SoC
- SoC ARCH symbols (existing SparX-5, new LAN969x) under the
ARCH_MICROCHIP hidden symbol (already in use by AT91 in 6.17)
- addition of that new symbol for drivers that are shared by
Microchip SoC-s now and in the future
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQ5TRCVIBiyi/S+BG4fOrpwrNPNDAUCaMgFkQAKCRAfOrpwrNPN
DFEbAQDg6iMOzL+C2tqu9eTfBZv9DCKcbfVFeHnwGqSbH8L/WgD/ZOq4UKIBMXpA
MGtwDDkDKBPVv3clF461/nS+VtAOaAE=
=upTs
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEo6/YBQwIrVS28WGKmmx57+YAGNkFAmjIIW4ACgkQmmx57+YA
GNlxCxAAgg82/SVuK6pB+Whj3JRn5Wt/grTLymy9gxPYqfbTMGnYEu2gG1nO9LBw
EhoDi9N2PH91qZ2PQwQGev+dLddK43CocPdPM+sYt0E4f7MGd9OS7jtxNKrJompr
DmIqwTwUMJu4dUhLkWkBBxrLjgisFQqAGFpVePgO8XJv2VmZ5DNzeub8e+3CeP3F
ogfcfc3TC3Si30SJtbJBnUZ1leod4Q7E2pzRjBLpdWEiJH5Otzh/WW4Q+n2BjLvd
fxHWPRri6UuEQGCdLbP6aa6U57C8JB69QbRIulmmjKdz2xtg/5FQqDpRFvTqBAGN
OBQVZaaV24ZHl1yXfqX/m08WTkUneHP9LNI+y0cunaHtX2z6Slr6DKhBU7Pj2XTS
B4M61lL4e/TUJHXbG+AZgqYTv6RCWf1vkYDRBa37We2sDUGgAsIZ4wmhKe2o4slT
TnRs0f2q3vGrbv3nz9F0PpS9WOZ6NJ+XSOpDofL0Qbb2DE8QfE5lzIT1tpqS9YRQ
xcPYfSwl0QFZxmflBhLaB4rRJxK76qYPipSi+uuWAJHy+BMOR6Yon9IUAoxATCE4
NREHCggb2QXAbbuqkKQJktnl7/gvEpbwKrN8WEq/oxqiPrFBZ5vsnjF7RGyXT2SB
tGcZ0F1dxFfA59R9BKVCLcVtpi9RHIux6to6PSsSHB2BvWDyBZw=
=zZ1l
-----END PGP SIGNATURE-----
Merge tag 'microchip-soc-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into soc/drivers
Microchip ARM64 SoC updates for v6.18:
This update includes:
- basic infrastructure support for Microchip LAN969x SoC
- SoC ARCH symbols (existing SparX-5, new LAN969x) under the
ARCH_MICROCHIP hidden symbol (already in use by AT91 in 6.17)
- addition of that new symbol for drivers that are shared by
Microchip SoC-s now and in the future
* tag 'microchip-soc-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
crypto: atmel-aes: make it selectable for ARCH_MICROCHIP
char: hw_random: atmel: make it selectable for ARCH_MICROCHIP
i2c: at91: make it selectable for ARCH_MICROCHIP
spi: atmel: make it selectable for ARCH_MICROCHIP
tty: serial: atmel: make it selectable for ARCH_MICROCHIP
mfd: at91-usart: Make it selectable for ARCH_MICROCHIP
arm64: lan969x: Add support for Microchip LAN969x SoC
arm64: Add config for Microchip SoC platforms
Link: https://lore.kernel.org/r/20250915123548.13722-1-nicolas.ferre@microchip.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Here are some small tty and serial driver fixes for 6.17-rc6 that
resolve some reported problems. Included in here are:
- 8250 driver dt bindings fixes
- broadcom serial driver binding fixes
- hvc_console bugfix
- xilinx serial driver bugfix
- sc16is7xx serial driver bugfix
All of these have been in linux-next for the past week with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCaMar1w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yk8AQCgx9deB0WhbxP/+3sVJ+0swX/bWdoAn3hCCy8f
P+QkteZ02Mmz25DS+gMB
=3mTh
-----END PGP SIGNATURE-----
Merge tag 'tty-6.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some small tty and serial driver fixes for 6.17-rc6 that
resolve some reported problems. Included in here are:
- 8250 driver dt bindings fixes
- broadcom serial driver binding fixes
- hvc_console bugfix
- xilinx serial driver bugfix
- sc16is7xx serial driver bugfix
All of these have been in linux-next for the past week with no
reported issues"
* tag 'tty-6.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: xilinx_uartps: read reg size from DTS
tty: hvc_console: Call hvc_kick in hvc_write unconditionally
dt-bindings: serial: 8250: allow "main" and "uart" as clock names
dt-bindings: serial: 8250: move a constraint
dt-bindings: serial: brcm,bcm7271-uart: Constrain clocks
serial: sc16is7xx: fix bug in flow control levels init
UART can be used as a wakeup source for am62 from suspend to ram states.
To enable wakeup from UART am62 requires a wakeup flag being set in the
pinctrl.
If the device is marked as wakeup enabled, select the 'wakeup' pinctrl
state on suspend and restore the default pinctrl state on resume.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Signed-off-by: Kendall Willis <k-willis@ti.com>
Link: https://lore.kernel.org/r/20250910-uart-daisy-chain-8250-omap-v2-2-e90d44c1a9ac@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When there is a heavy load of receiving characters to all
four UART's, the warning 'Hardware RX FIFO overrun' is
sometimes detected.
The current implementation always service first the highest UART
until no more interrupt and then service another UART
(ex: UART3 will be serviced for as long as there are interrupts
for it, then UART2, etc).
This commit handle all individual interrupt sources before
reading the global IRQ register again.
This commit has also a nice side-effect of improving the efficiency
of the driver by reducing the number of reads of the global
IRQ register.
Signed-off-by: Tapio Reijonen <tapio.reijonen@vaisala.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Reviewed-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20250908-master-max310x-improve-interrupt-handling-v3-1-91985e82ba39@vaisala.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
LAN969x uses the Atmel USART serial, so make it selectable for
ARCH_MICROCHIP to avoid needing to update depends in future if other
Microchip SoC-s use it as well.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Current implementation uses `CDNS_UART_REGISTER_SPACE(0x1000)`
for request_mem_region() and ioremap() in cdns_uart_request_port() API.
The cadence/xilinx IP has register space defined from offset 0x0 to 0x48.
It also mentions that the register map is defined as [6:0]. So, the upper
region may/maynot be used based on the IP integration.
In Axiado AX3000 SoC two UART instances are defined
0x100 apart. That is creating issue in some other instance due to overlap
with addresses.
Since, this address space is already being defined in the
devicetree, use the same when requesting the register space.
Fixes: 1f70557790 ("arm64: dts: axiado: Add initial support for AX3000 SoC and eval board")
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Harshit Shah <hshah@axiado.com>
Link: https://lore.kernel.org/r/20250902-xilinx-uartps-reg-size-v3-1-d11cfa7258e3@axiado.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In vt_ioctl(), the handler for VT_RESIZE always returns 0, which prevents
users from detecting errors. Add the missing return value so that errors
can be properly reported to users like vt_resizex().
Signed-off-by: Zizhi Wo <wozizhi@huaweicloud.com>
Link: https://lore.kernel.org/r/20250904023955.3892120-1-wozizhi@huaweicloud.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previous commit edab558feb ("vt: sort out locking for font handling")
move the vc_mode check into console_lock protect, but forget to remove the
old check in con_font_set(). Just remove the redundant check.
Signed-off-by: Wang Liang <wangliang74@huawei.com>
Link: https://lore.kernel.org/r/20250904023345.13731-1-wangliang74@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GENI UART driver currently supports only non-DFS (Dynamic Frequency
Scaling) mode for source frequency selection. However, to operate correctly
in DFS mode, the GENI SCLK register must be programmed with the appropriate
DFS index. Failing to do so can result in incorrect frequency selection
Add support for Dynamic Frequency Scaling (DFS) mode in the GENI UART
driver by configuring the GENI_CLK_SEL register with the appropriate DFS
index. This ensures correct frequency selection when operating in DFS mode.
Replace the UART driver-specific logic for clock selection with the GENI
common driver function to obtain the desired frequency and corresponding
clock index. This improves maintainability and consistency across
GENI-based drivers.
Signed-off-by: Viken Dadhaniya <viken.dadhaniya@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250903063136.3015237-1-viken.dadhaniya@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently gsm_queue() processes incoming frames and when opening
a DLC channel it calls gsm_dlci_open() which calls gsm_modem_update().
If basic mode is used it calls gsm_modem_upd_via_msc() and it
cannot block the input queue by waiting the response to come
into the same input queue.
Instead allow sending Modem Status Command without waiting for remote
end to respond. Define a new function gsm_modem_send_initial_msc()
for this purpose. As MSC is only valid for basic encoding, it does
not do anything for advanced or when convergence layer type 2 is used.
Fixes: 4847380250 ("tty: n_gsm: fix missing update of modem controls after DLCI open")
Signed-off-by: Seppo Takalo <seppo.takalo@nordicsemi.no>
Link: https://lore.kernel.org/r/20250827123221.1148666-1-seppo.takalo@nordicsemi.no
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ida_alloc_range() function expects an inclusive range, meaning both
the start and end values are valid allocation targets. Passing nr_ports
as the upper bound allows allocation of an ID equal to nr_ports, which
is out of bounds when used as an index into the port array.
Fix this by subtracting 1 from nr_ports in both calls to ida_alloc_range(),
ensuring the allocated ID stays within the valid range
[start, nr_ports - 1].
This prevents potential out-of-bounds access when the allocated ID is used
as an index.
Fixes: 9391ab1ed9 ("serial: qcom-geni: Make UART port count configurable via Kconfig")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/r/202508180815.R2nDyajs-lkp@intel.com/
Signed-off-by: Zong Jiang <quic_zongjian@quicinc.com>
Link: https://lore.kernel.org/r/20250827120319.1682835-1-quic_zongjian@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Starting with commit f99508074e ("PM: domains: Detach on
device_unbind_cleanup()"), there is no longer a need to call
dev_pm_domain_detach() in the bus remove function. The
device_unbind_cleanup() function now handles this to avoid
invoking devres cleanup handlers while the PM domain is
powered off, which could otherwise lead to failures as
described in the above-mentioned commit.
Drop the explicit dev_pm_domain_detach() call and rely instead
on the flags passed to dev_pm_domain_attach() to power off the
domain.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20250827101747.928265-1-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The result of integer comparison already evaluates to bool. No need for
explicit conversion.
Signed-off-by: Xichao Zhao <zhao.xichao@vivo.com>
Link: https://lore.kernel.org/r/20250827024514.76149-1-zhao.xichao@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Support "\e[?1049h" and "\e[?1049l" escape codes.
This patch allows programs to enter and leave alternate screens.
This feature is widely available in graphical terminal emulators and mostly
used by fullscreen terminal-based user interfaces such as text editors.
Most editors such as vim and nano assume this escape code in not supported
and will not try to print the escape sequence if TERM=linux.
To try out this patch, run `TERM=xterm-256color vim` inside a VT.
Signed-off-by: Calixte Pernot <calixte.pernot@grenoble-inp.org>
Link: https://lore.kernel.org/r/20250825125607.2478-3-calixte.pernot@grenoble-inp.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dev_err_probe() doesn't do anything when error is '-ENOMEM'.
Make the following two changes:
(1) Replace -ENOMEM with -ENOSPC in max3100_probe().
(2) Just return -ENOMEM instead in max310x_probe().
Signed-off-by: Xichao Zhao <zhao.xichao@vivo.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250819120927.607744-1-zhao.xichao@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After hvc_write completes, call hvc_kick also in the case the output
buffer has been drained, to ensure tty_wakeup gets called.
This fixes that functions which wait for a drained buffer got stuck
occasionally.
Cc: stable <stable@kernel.org>
Closes: https://bugzilla.opensuse.org/show_bug.cgi?id=1230062
Signed-off-by: Fabian Vogt <fvogt@suse.de>
Link: https://lore.kernel.org/r/2011735.PYKUYFuaPT@fvogt-thinkpad
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Having all the new guards, use them in the vt code. This improves
readability, makes error handling easier, and marks locked portions of
code explicit.
A local free_page_ptr __free guard is introduced for
__get_free_page/free_page (with proper casts). This could be made public
in include/. But I am not sure if there are more possible users, so
keeping completely private here.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250814072456.182853-16-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Having all the new guards, use them in the 8250_rsa code. This improves
readability, makes error handling easier, and marks locked portions of
code explicit.
The new __free()-annotated declarations are moved to the allocation points
as is preferred:
https://lore.kernel.org/all/CAHk-=wjvh_LUpa=864joG2JJXs3+viO-kLzLidR2JLyMr4MNwA@mail.gmail.com/
Except font_data in con_font_get(). The scope in there would not match
the expected lifetime. But the declaration is moved closer.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250814072456.182853-15-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Having all the new guards, use them in the 8250_rsa code. This improves
readability, makes error handling easier, and marks locked portions of
code explicit.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250814072456.182853-14-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Having all the new guards, use them in the 8250_omap code. This improves
readability, makes error handling easier, and marks locked portions of
code explicit.
For this to work, UART_CAP_RPM has to be set to up->capabilities a bit
earlier.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250814072456.182853-13-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To use guard()s easily in omap_8250_set_termios(), split it into atomic
and non-atomic part. The former can be easily guarded -- without a need
of indenting or moving code.
omap_8250_set_termios() would likely profit from a cleanup similar to
one in serial8250_do_set_termios() in commit cdc4a3e0b2 ("serial:
8250: extract serial8250_set_fcr()") and earlier.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250814072456.182853-12-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Having all the new guards, use them in the 8250 code. This improves
readability, makes error handling easier, and marks locked portions of
code explicit.
serial_unlink_irq_chain() is done separately here because with the
guard() used, those BUG_ON()s can be switched WARN_ON()s as we can
actually handle the conditions and return (despite something went really
wrong).
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250814072456.182853-11-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Having all the new guards, use them in the 8250 code. This improves
readability, makes error handling easier, and marks locked portions of
code explicit.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250814072456.182853-10-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Having all the new guards, use them in the serial_core code. This
improves readability, makes error handling easier, and marks locked
portions of code explicit.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250814072456.182853-9-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Having all the new guards, use them in the mxser code. This improves
readability, makes error handling easier, and marks locked portions of
code explicit.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250814072456.182853-8-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
