On the embedded platform, certain critical data, such as IMU data, is
transmitted through UART. The tty_flip_buffer_push() interface in the TTY
layer uses system_dfl_wq to handle the flipping of the TTY buffer.
Although the unbound workqueue can create new threads on demand and wake
up the kworker thread on an idle CPU, it may be preempted by real-time
tasks or other high-prio tasks.
flush_to_ldisc() needs to wake up the relevant data handle thread. When
executing __wake_up_common_lock(), it calls spin_lock_irqsave(), which
does not disable preemption but disables migration in RT-Linux. This
prevents the kworker thread from being migrated to other cores by CPU's
balancing logic, resulting in long delays. The call trace is as follows:
__wake_up_common_lock
__wake_up
ep_poll_callback
__wake_up_common
__wake_up_common_lock
__wake_up
n_tty_receive_buf_common
n_tty_receive_buf2
tty_ldisc_receive_buf
tty_port_default_receive_buf
flush_to_ldisc
In our system, the processing interval for each frame of IMU data
transmitted via UART can experience significant jitter due to this issue.
Instead of the expected 10 to 15 ms frame processing interval, we see
spikes up to 30 to 35 ms. Moreover, in just one or two hours, there can
be 2 to 3 occurrences of such high jitter, which is quite frequent. This
jitter exceeds the software's tolerable limit of 20 ms.
Introduce flip_wq in tty_port which can be set by tty_port_link_wq() or as
default linked to default workqueue allocated when tty_register_driver().
The default workqueue is allocated with flag WQ_SYSFS, so that cpumask and
nice can be set dynamically. The execution timing of tty_port_link_wq() is
not clearly restricted. The newly added function tty_port_link_driver_wq()
checks whether the flip_wq of the tty_port has already been assigned when
linking the default tty_driver's workqueue to the port. After the user has
set a custom workqueue for a certain tty_port using tty_port_link_wq(), the
system will only use this custom workqueue, even if tty_driver does not
have %TTY_DRIVER_NO_WORKQUEUE flag. When tty_port register device, flip_wq
link operation is done by tty_port_link_driver_wq(), but for in-memory
devices the link operation cannot cover all the cases. Although
tty_port_install() is dedicated for in-memory devices lik PTY to link port
allocated on demand, the logic of tty_port_install() is so simple that
people may not call it, vc_cons[0].d->port is one such case. We check the
buf.flip_wq when flip TTY buffer, if buf.flip_wq of TTY port is NULL, use
system_dfl_wq as a backup.
To avoid naming conflict of the default tty_driver's workqueue, using
'"%s-%s", driver->name, driver->driver_name' as the workqueue name. In
cases where driver_name is not specified and therefore is NULL, the
workqueue is not created. Drivers that do not define driver_name are
potentially in-memory devices like vty, which generally do not require
special workqueue settings. Even with the combination of name and
driver_name, the workqueue names can still be duplicated, as many tty
serial drivers use "ttyS" as dev_name and "serial" as driver_name. I
modified the conflicting driver_name of these drivers by appending a
suffix of _xx based on the corresponding .c file. If this modification is
not made, it could not only lead to duplicate workqueue names but also
result in duplicate entries for the /proc/tty/driver/<driver_name> nodes.
Introduce %TTY_DRIVER_NO_WORKQUEUE flag meaning not to create the
default single tty_driver workqueue. Two reasons why need to introduce the
%TTY_DRIVER_NO_WORKQUEUE flag:
1. If the WQ_SYSFS parameter is enabled, workqueue_sysfs_register() will
fail when trying to create a workqueue with the same name. The pty is an
example of this; if both CONFIG_LEGACY_PTYS and CONFIG_UNIX98_PTYS are
enabled, the call to tty_register_driver() in unix98_pty_init() will fail.
2. Different TTY ports may be used for different tasks, which may require
separate core binding control via workqueues. In this case, the workqueue
created by default in the TTY driver is unnecessary. Enabling this flag
prevents the creation of this redundant workqueue.
After applying this patch, we can set the related UART TTY flip buffer
workqueue by sysfs. We set the cpumask to CPU cores associated with the
IMU tasks, and set the nice to -20. Testing has shown significant
improvement in the previously described issue, with almost no stuttering
occurring anymore.
Tested-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Xin Zhao <jackzxcui1989@163.com>
Link: https://patch.msgid.link/20260213085039.3274704-1-jackzxcui1989@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When userspace enables flow control (CRTSCTS), the driver
deasserts RTS even when the receive buffer has space. This prevents the
peer device from transmitting, causing communication to stall.
The root cause is that the driver unconditionally uses manual RTS control
regardless of flow control mode. When CRTSCTS is set, the hardware should
automatically manage RTS based on buffer status, but the driver overrides
this by setting manual control.
Fix this by introducing port->manual_flow flag. In set_termios(), disable
manual flow when CRTSCTS is set. In set_mctrl(), only assert
SE_UART_MANUAL_RFR when manual_flow is active. Verified by enabling and
disabling hardware flow control with stty.
Signed-off-by: Anup Kulkarni <anup.kulkarni@oss.qualcomm.com>
Link: https://patch.msgid.link/20260310104155.339010-1-anup.kulkarni@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since sdma hardware configure postpone to transfer phase, have to
disable dma request before dma transfer setup because there is a
hardware limitation on sdma event enable(ENBLn) as below.
Refer SDMA 2.6.28 Channel Enable RAM (SDMAARMx_CHNENBLn) section:
"It is thus essential for the Arm platform to program them before any
DMA request is triggered to the SDMA, otherwise an unpredictable
combination of channels may be started."
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://patch.msgid.link/20260312094526.297348-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for the SystemBase Multi I/O serial cards, which are
"compatible" with a standard 16550A controllers, except that they need
to have their interrupts enabled in a proprietary way.
Tested with a Delock "Serial PCI Express x1 Card 8x Serial RS-232".
Signed-off-by: Michael Walle <mwalle@kernel.org>
Link: https://patch.msgid.link/20260225081739.946723-1-mwalle@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver currently only supports builds against a PIC32 target, or
with COMPILE_TEST on MIPS. Now that commit 24cad1a228 ("serial:
pic32_uart: update include to use pic32.h from platform_data") is
merged, it's possible to compile this driver on other architectures.
To avoid future breakage of this driver in the future, let's update the
Kconfig so that it can be built with COMPILE_TEST enabled on all
architectures.
Signed-off-by: Brian Masney <bmasney@redhat.com>
Link: https://patch.msgid.link/20260222-serial-pic32-v1-1-8fdbc0d0d334@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver runs also on SoCs without a Tegra20 APB DMA controller (e.g.
Tegra234).
Remove the Kconfig dependency on TEGRA20_APB_DMA, and remove reference to
the APB DMA controller from the Kconfig help text.
Signed-off-by: Francesco Lavra <flavra@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20260303111438.2691799-1-flavra@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a check for clk_enable() in auart_console_write(). If
clk_enable() fails, return immediately to avoid accessing
hardware registers while the clock is not enabled.
Signed-off-by: Zhaoyang Yu <2426767509@qq.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/tencent_AB29FADF1FAD67D818283B6BB4FDF66F2F08@qq.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These drivers were added about 3 years ago, and depend on the
XTENSA_PLATFORM_ESP32 config option which has never existed,
so no device can actually use them.
They can only be compiled with COMPILE_TEST.
In a previous conversation [1], Greg suggested removing the
drivers, and Max, the original submitter of the drivers, agreed
due to a lack of foreseeable development.
Link: https://lore.kernel.org/all/20260308131412.1102749-1-julianbraha@gmail.com/ [1]
Signed-off-by: Julian Braha <julianbraha@gmail.com>
Link: https://patch.msgid.link/20260309122321.1528622-1-julianbraha@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some DMA controllers require transfer lengths to be aligned to a
specific boundary. For example, the Tegra GPC DMA requires 4-byte
(word) aligned transfers and will reject unaligned lengths.
Align the TX DMA buffer length down to the DMA controller's copy_align
boundary before submitting the transfer. Any remaining unaligned bytes
will be transmitted via PIO on subsequent calls, which is the existing
fallback behavior when DMA is not used.
Signed-off-by: Kartik Rajput <kkartik@nvidia.com>
Link: https://patch.msgid.link/20260225065915.341522-5-kkartik@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for the NVIDIA Tegra264 UART controller, which is derived
from the AMBA PL011 design.
On Tegra264, the fractional baud rate divisor (FBRD) register is broken.
Using IBRD alone may not achieve the required baud rate
tolerance. Enable the skip_ibrd_fbrd and set_uartclk_rate flags for
the NVIDIA variant.
Signed-off-by: Kartik Rajput <kkartik@nvidia.com>
Link: https://patch.msgid.link/20260225065915.341522-4-kkartik@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The NVIDIA Tegra264 UART relies on configuring the UART clock rate
directly to program the desired baud rate.
Introduce the set_uartclk_rate vendor flag. When set, the driver
uses clk_set_rate() to program the UART clock to the desired baud
rate and clk_round_rate() to determine the maximum supported baud
rate.
Signed-off-by: Kartik Rajput <kkartik@nvidia.com>
Link: https://patch.msgid.link/20260225065915.341522-3-kkartik@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The NVIDIA Tegra264 UART has a broken fractional baud rate
divisor register. Using IBRD and FBRD may cause the baud rate
to fall outside the required tolerance.
Introduce the skip_ibrd_fbrd vendor flag to skip IBRD/FBRD
programming. When set, the baud rate is derived directly from the
UART clock rate using a fixed divisor.
Signed-off-by: Kartik Rajput <kkartik@nvidia.com>
Link: https://patch.msgid.link/20260225065915.341522-2-kkartik@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the PL011 driver only enables the UART (by setting UARTEN
in REG_CR) in pl011_startup(), so if it is used for earlycon it is
relying on the bootrom/firmware having left the UART enabled.
There's no particular reason not to actively enable the UART before
using it for earlycon, and the earlycon handling for e.g. the 8250
UART sets up the UART in its setup function, so follow that in the
PL011.
This allows use of earlycon with a UART that the firmware hasn't
already been using for its own output, but the main motivation is
that QEMU will otherwise log a message complaining that the guest is
trying to write to a UART it never enabled.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://patch.msgid.link/20260210125100.223138-1-peter.maydell@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial8250_release_dma() is NULL-aware, no need to check this in the caller.
While at it, make sure DMA won't be used again, by NULLifying the pointer.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://patch.msgid.link/20260128142726.128175-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a05025d0ce ("tty: serial: samsung_tty: use standard
debugging macros") changed the debug prints to dev_dbg, which can
result in deadlocks:
s3c24xx_serial_set_termios can be called with the port lock, and then
calls dev_dbg, which needs the console mutex. At the same time,
s3c24xx_serial_console_write can be called with the console lock
(e.g., inside console_unlock), and needs the port lock.
To avoid this, move one dev_dbg call and just delete the other.
Signed-off-by: Alyssa Milburn <amilburn@zall.org>
Link: https://patch.msgid.link/aXny9km6N1v9eoXU@zall.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts some of the visually simpler cases that have been split
over multiple lines. I only did the ones that are easy to verify the
resulting diff by having just that final GFP_KERNEL argument on the next
line.
Somebody should probably do a proper coccinelle script for this, but for
me the trivial script actually resulted in an assertion failure in the
middle of the script. I probably had made it a bit _too_ trivial.
So after fighting that far a while I decided to just do some of the
syntactically simpler cases with variations of the previous 'sed'
scripts.
The more syntactically complex multi-line cases would mostly really want
whitespace cleanup anyway.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the exact same thing as the 'alloc_obj()' version, only much
smaller because there are a lot fewer users of the *alloc_flex()
interface.
As with alloc_obj() version, this was done entirely with mindless brute
force, using the same script, except using 'flex' in the pattern rather
than 'objs*'.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This was done entirely with mindless brute force, using
git grep -l '\<k[vmz]*alloc_objs*(.*, GFP_KERNEL)' |
xargs sed -i 's/\(alloc_objs*(.*\), GFP_KERNEL)/\1)/'
to convert the new alloc_obj() users that had a simple GFP_KERNEL
argument to just drop that argument.
Note that due to the extreme simplicity of the scripting, any slightly
more complex cases spread over multiple lines would not be triggered:
they definitely exist, but this covers the vast bulk of the cases, and
the resulting diff is also then easier to check automatically.
For the same reason the 'flex' versions will be done as a separate
conversion.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the result of running the Coccinelle script from
scripts/coccinelle/api/kmalloc_objs.cocci. The script is designed to
avoid scalar types (which need careful case-by-case checking), and
instead replace kmalloc-family calls that allocate struct or union
object instances:
Single allocations: kmalloc(sizeof(TYPE), ...)
are replaced with: kmalloc_obj(TYPE, ...)
Array allocations: kmalloc_array(COUNT, sizeof(TYPE), ...)
are replaced with: kmalloc_objs(TYPE, COUNT, ...)
Flex array allocations: kmalloc(struct_size(PTR, FAM, COUNT), ...)
are replaced with: kmalloc_flex(*PTR, FAM, COUNT, ...)
(where TYPE may also be *VAR)
The resulting allocations no longer return "void *", instead returning
"TYPE *".
Signed-off-by: Kees Cook <kees@kernel.org>
Here is the small amount of tty and serial driver updates for 7.0-rc1.
Nothing major in here at all, just some driver updates and minor tweaks
and cleanups including:
- sh-sci serial driver updates
- 8250 driver updates
- attempt to make the tty ports have their own workqueue, but was
reverted after testing found it to have problems on some platforms.
This will probably come back for 7.1 after it has been reworked and
resubmitted
- other tiny tty driver changes
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCaZR1VQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykfsACghiyMgr0XKVDFEpV7/fPzocKH+o0An3v8knSi
kLz/f6LstVsISqCxeT+9
=uozB
-----END PGP SIGNATURE-----
Merge tag 'tty-7.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver updates from Greg KH:
"Here is the small amount of tty and serial driver updates for 7.0-rc1.
Nothing major in here at all, just some driver updates and minor
tweaks and cleanups including:
- sh-sci serial driver updates
- 8250 driver updates
- attempt to make the tty ports have their own workqueue, but was
reverted after testing found it to have problems on some platforms.
This will probably come back for 7.1 after it has been reworked and
resubmitted
- other tiny tty driver changes
All of these have been in linux-next for a while with no reported
problems"
* tag 'tty-7.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (49 commits)
Revert "tty: tty_port: add workqueue to flip TTY buffer"
tty: tty_port: add workqueue to flip TTY buffer
serial: 8250_pci: Remove custom deprecated baud setting routine
serial: 8250_omap: Remove custom deprecated baud setting routine
dt-bindings: serial: renesas,scif: Document RZ/G3L SoC
serial: 8250: omap: set out-of-band wakeup if wakeup pinctrl exists
tty: hvc-iucv: Remove KMSG_COMPONENT macro
dt-bindings: serial: google,goldfish-tty: Convert to DT schema
dt-bindings: serial: sh-sci: Fold single-entry compatibles into enum
serial: 8250: 8250_omap.c: Clear DMA RX running status only after DMA termination is done
serial: 8250: 8250_omap.c: Add support for handling UART error conditions
serial: SH_SCI: improve "DMA support" prompt
serial: Kconfig: fix ordering of entries for menu display
serial: 8250: fix ordering of entries for menu display
serial: imx: change SERIAL_IMX_CONSOLE to bool
8250_men_mcb: drop unneeded MODULE_ALIAS
serial: men_z135_uart: drop unneeded MODULE_ALIAS
dt-bindings: serial: renesas,rsci: Document RZ/V2H(P) and RZ/V2N SoCs
serial: rsci: Convert to FIELD_MODIFY()
dt-bindings: serial: 8250: add SpacemiT K3 UART compatible
...
Use the linux/platform_data/pic32.h include instead of
asm/mach-pic32/pic32.h so that the asm variant can be dropped. This
is in preparation for allowing some drivers to be compiled on other
architectures with COMPILE_TEST enabled.
Signed-off-by: Brian Masney <bmasney@redhat.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
As comments mentioned this is old (and actually deprecated) interface
to set custom baud rates. This interface has limitations as it only
allows to set a single opaque value called "custom_divisor". If the HW
needs more complex settings (like fractional divisor) it must somehow
encode this. This is horrid interface that is very driver specific
and not flexible. Meanwhile Linux has established way to set free
baud rate settings via BOTHER [1]. With all this being said, remove
deprecated interface for good.
Link: https://stackoverflow.com/questions/12646324/how-can-i-set-a-custom-baud-rate-on-linux [1]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20260122102349.2395423-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As comments mentioned this is old (and actually deprecated) interface
to set custom baud rates. This interface has limitations as it only
allows to set a single opaque value called "custom_divisor". If the HW
needs more complex settings (like fractional divisor) it must somehow
encode this. This is horrid interface that is very driver specific
and not flexible. Meanwhile Linux has established way to set free
baud rate settings via BOTHER [1]. With all this being said, remove
deprecated interface for good.
Link: https://stackoverflow.com/questions/12646324/how-can-i-set-a-custom-baud-rate-on-linux [1]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20260122102349.2395423-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In TI K3 SoCs, I/O daisy chaining is used to allow wakeup from UART when the
UART controller is off. Set UART device as wakeup capable using out-of-band
wakeup if the 'wakeup' pinctrl state exists and the device may wakeup.
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Kendall Willis <k-willis@ti.com>
Link: https://patch.msgid.link/20260116-uart-wakeup-v2-1-0078ae9996e4@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Revert commit bfc467db60 ("serial: remove redundant
tty_port_link_device()") because the tty_port_link_device() is not
redundant: the tty->port has to be confured before we call
uart_configure_port(), otherwise user-space can open console without TTY
linked to the driver.
This tty_port_link_device() was added explicitly to avoid this exact
issue in commit fb2b90014d ("tty: link tty and port before configuring
it as console"), so offending commit basically reverted the fix saying
it is redundant without addressing the actual race condition presented
there.
Reproducible always as tty->port warning on Qualcomm SoC with most of
devices disabled, so with very fast boot, and one serial device being
the console:
printk: legacy console [ttyMSM0] enabled
printk: legacy console [ttyMSM0] enabled
printk: legacy bootconsole [qcom_geni0] disabled
printk: legacy bootconsole [qcom_geni0] disabled
------------[ cut here ]------------
tty_init_dev: ttyMSM driver does not set tty->port. This would crash the kernel. Fix the driver!
WARNING: drivers/tty/tty_io.c:1414 at tty_init_dev.part.0+0x228/0x25c, CPU#2: systemd/1
Modules linked in: socinfo tcsrcc_eliza gcc_eliza sm3_ce fuse ipv6
CPU: 2 UID: 0 PID: 1 Comm: systemd Tainted: G S 6.19.0-rc4-next-20260108-00024-g2202f4d30aa8 #73 PREEMPT
Tainted: [S]=CPU_OUT_OF_SPEC
Hardware name: Qualcomm Technologies, Inc. Eliza (DT)
...
tty_init_dev.part.0 (drivers/tty/tty_io.c:1414 (discriminator 11)) (P)
tty_open (arch/arm64/include/asm/atomic_ll_sc.h:95 (discriminator 3) drivers/tty/tty_io.c:2073 (discriminator 3) drivers/tty/tty_io.c:2120 (discriminator 3))
chrdev_open (fs/char_dev.c:411)
do_dentry_open (fs/open.c:962)
vfs_open (fs/open.c:1094)
do_open (fs/namei.c:4634)
path_openat (fs/namei.c:4793)
do_filp_open (fs/namei.c:4820)
do_sys_openat2 (fs/open.c:1391 (discriminator 3))
...
Starting Network Name Resolution...
Apparently the flow with this small Yocto-based ramdisk user-space is:
driver (qcom_geni_serial.c): user-space:
============================ ===========
qcom_geni_serial_probe()
uart_add_one_port()
serial_core_register_port()
serial_core_add_one_port()
uart_configure_port()
register_console()
|
| open console
| ...
| tty_init_dev()
| driver->ports[idx] is NULL
|
tty_port_register_device_attr_serdev()
tty_port_link_device() <- set driver->ports[idx]
Fixes: bfc467db60 ("serial: remove redundant tty_port_link_device()")
Cc: stable@vger.kernel.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://patch.msgid.link/20260123072139.53293-2-krzysztof.kozlowski@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fintek F81504/508/512 can support both RTS_ON_SEND and RTS_AFTER_SEND,
but pci_fintek_rs485_supported only announces the former.
This makes it impossible to unset SER_RS485_RTS_ON_SEND from
userspace because of uart_sanitize_serial_rs485(). Some devices
with these chips need RTS low on TX, so they are effectively broken.
Fix this by announcing the support for SER_RS485_RTS_AFTER_SEND,
similar to commit 068d35a7be ("serial: sc16is7xx: announce support
for SER_RS485_RTS_ON_SEND").
Fixes: 4afeced55b ("serial: core: fix sanitizing check for RTS settings")
Cc: stable <stable@kernel.org>
Signed-off-by: Marnix Rijnart <marnix.rijnart@iwell.eu>
Link: https://patch.msgid.link/20260112000931.61703-1-marnix.rijnart@iwell.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 10904d725f ("serial: qcom-geni: Enable PM runtime for serial
driver") caused BT init to fail during bootup on the RB2 platform,
preventing proper BT initialization. However, BT works correctly after
bootup completes.
The issue occurs when runtime PM is enabled and uart_add_one_port() is
called before wakeup IRQ setup. The uart_add_one_port() call activates
the device through runtime PM, which configures GPIOs to the "qup_x"
pinmux function during runtime resume. When wakeup IRQ registration
happens afterward using dev_pm_set_dedicated_wake_irq(), these GPIOs
are reset back to the "gpio" pinmux function, which impacts the RX GPIO
and leads to Bluetooth failures.
Fix this by ensuring wakeup IRQ setup is completed before calling
uart_add_one_port() to prevent the pinmux function conflict.
Fixes: 10904d725f ("serial: qcom-geni: Enable PM runtime for serial driver")
Reported-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Closes: https://lore.kernel.org/all/20251110101043.2108414-4-praveen.talari@oss.qualcomm.com/
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Praveen Talari <praveen.talari@oss.qualcomm.com>
Link: https://patch.msgid.link/20260108041006.1874757-1-praveen.talari@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clear rx_running flag only after DMA teardown polling completes. In the
previous implementation the flag was being cleared while hardware teardown
was still in progress, creating a mismatch between software state
(flag = 0, "ready") and hardware state (still terminating).
Signed-off-by: Moteen Shah <m-shah@ti.com>
Link: https://patch.msgid.link/20260112081829.63049-3-m-shah@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DMA IRQ handler does not accounts for the overrun(OE) or any other
errors being reported by the IP before triggering a DMA transaction which
leads to the interrupts not being handled resulting into an IRQ storm.
The way to handle OE is to:
1. Reset the RX FIFO.
2. Read the UART_RESUME register, which clears the internal flag
Earlier, the driver issued DMA transations even in case of OE which shouldn't
be done according to the OE handling mechanism mentioned above, as we are
resetting the FIFO's, refer section: "12.1.6.4.8.1.3.6 Overrun During
Receive" [0].
[0] https://www.ti.com/lit/pdf/spruiu1
Signed-off-by: Moteen Shah <m-shah@ti.com>
Link: https://patch.msgid.link/20260112081829.63049-2-m-shah@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Having a prompt of "DMA support" suddenly appear during a
"make oldconfig" can be confusing. Add a little helpful text to
the prompt message.
Fixes: 73a19e4c03 ("serial: sh-sci: Add DMA support.")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260110232643.3533351-5-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Improve the "Non-8250 serial port support" menu so that entries in it
are displayed in a better order (_CONSOLE after its driver) and so that
intervening symbols don't break up the dependency list, allowing menu
entries to be displayed with proper indentation.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://patch.msgid.link/20260110232643.3533351-4-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Improve the "8250/16550 serial support" menu so that entries in it
are displayed in a better order (reorder a few symbols) and so that
intervening symbols don't break up the dependency list, allowing menu
entries to be displayed with proper indentation.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://patch.msgid.link/20260110232643.3533351-3-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SERIAL_IMX_CONSOLE is a build option for the imx driver (SERIAL_IMX).
It does not build a separate console driver file, so it can't be built
as a module since it isn't built at all.
Change the Kconfig symbol from tristate to bool and update the help
text accordingly.
Fixes: 0db4f9b91c ("tty: serial: imx: enable imx serial console port as module")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://patch.msgid.link/20260110232643.3533351-2-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 1f4ea4838b ("mcb: Add missing modpost build support")
the MODULE_ALIAS() is redundant as the module alias is now
automatically generated from the MODULE_DEVICE_TABLE().
Remove the explicit alias.
No functional change intended.
Reviewed-by: Jorge Sanjuan Garcia <dev-jorge.sanjuangarcia@duagon.com>
Signed-off-by: Jose Javier Rodriguez Barbarin <dev-josejavier.rodriguez@duagon.com>
Link: https://patch.msgid.link/20260108134110.25278-3-dev-josejavier.rodriguez@duagon.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 1f4ea4838b ("mcb: Add missing modpost build support")
the MODULE_ALIAS() is redundant as the module alias is now
automatically generated from the MODULE_DEVICE_TABLE().
Remove the explicit alias.
No functional change intended.
Reviewed-by: Jorge Sanjuan Garcia <dev-jorge.sanjuangarcia@duagon.com>
Signed-off-by: Jose Javier Rodriguez Barbarin <dev-josejavier.rodriguez@duagon.com>
Link: https://patch.msgid.link/20260108134110.25278-2-dev-josejavier.rodriguez@duagon.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
RTS line control with delay should be triggered when there is no more
bytes in kfifo and hardware buffer is empty. Without this patch RTS
control is scheduled right after feeding hardware buffer and this is too
early.
RTS line may change state before hardware buffer is empty.
With this patch delayed RTS state change is triggered when function
cdns_uart_handle_tx is called from cdns_uart_isr on
CDNS_UART_IXR_TXEMPTY exactly when hardware completed transmission
Fixes: fccc9d9233 ("tty: serial: uartps: Add rs485 support to uartps driver")
Cc: stable <stable@kernel.org>
Link: https://patch.msgid.link/20251221103221.1971125-1-jakub.turek@elsta.tech
Signed-off-by: Jakub Turek <jakub.turek@elsta.tech>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver updates struct sci_port::tx_cookie to zero right before the TX
work is scheduled, or to -EINVAL when DMA is disabled.
dma_async_is_complete(), called through dma_cookie_status() (and possibly
through dmaengine_tx_status()), considers cookies valid only if they have
values greater than or equal to 1.
Passing zero or -EINVAL to dmaengine_tx_status() before any TX DMA
transfer has started leads to an incorrect TX status being reported, as the
cookie is invalid for the DMA subsystem. This may cause long wait times
when the serial device is opened for configuration before any TX activity
has occurred.
Check that the TX cookie is valid before passing it to
dmaengine_tx_status().
Fixes: 7cc0e0a43a ("serial: sh-sci: Check if TX data was written to device in .tx_empty()")
Cc: stable <stable@kernel.org>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://patch.msgid.link/20251217135759.402015-1-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During restoring sysfs fwnode information the information of_node_reused
was dropped. This was previously set by device_set_of_node_from_dev().
Add it back manually
Fixes: 24ec03cc55 ("serial: core: Restore sysfs fwnode information")
Cc: stable <stable@kernel.org>
Suggested-by: Cosmin Tanislav <demonsingur@gmail.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Tested-by: Michael Walle <mwalle@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Cosmin Tanislav <demonsingur@gmail.com>
Link: https://patch.msgid.link/20251219152813.1893982-1-alexander.stein@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The devm_platform_get_and_ioremap_resource() function never returns
NULL, it returns error pointers. Fix the error checking to match.
Fixes: 25e95d7631 ("serial: 8250: Add Loongson uart driver support")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://patch.msgid.link/aSsIa3KdAlXh5uQC@stanley.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The change that restores sysfs fwnode information does it only for OF cases.
Update the fix to cover all possible types of fwnodes.
Fixes: d36f0e9a00 ("serial: core: restore of_node information in sysfs")
Cc: stable <stable@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20251127163650.2942075-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for RZ/G3E RSCI. RSCI IP found on the RZ/G3E SoC is similar
to RZ/T2H, but it has a 32-stage FIFO. It has 6 clocks(5 module clocks
+ 1 external clock) instead of 3 clocks(2 module clocks + 1 external
clock) on T2H, has 6 irqs compared to 4 on RZ/T2H and has multiple resets.
Add support for the hardware flow control.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://patch.msgid.link/20251129164325.209213-18-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rename rsci_early_console_setup()->rsci_rzt2h_early_console_setup(),
the early_console data of_sci_rsci_data->of_rsci_rzt2h_data and the
port_params rsci_port_params->rsci_rzt2h_port_params to support RZ/G3E
RSCI that uses different data and callback().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://patch.msgid.link/20251129164325.209213-17-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add finish_console_write() callback as RZ/G3E RSCI IP needs special
handling compared to other SoCs.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://patch.msgid.link/20251129164325.209213-16-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make the function sci_scbrr_calc() public for code reuse to support RZ/G3E
RSCI IP.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://patch.msgid.link/20251129164325.209213-15-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The RZ/G3E RSCI IP has 32-stage FIFO compared to 16-stage FIFO on RZ/T2H.
Add RSCI_PORT_SCIF32 port ID to differentiate it from RZ/T2H RSCI and
update sci_is_rsci_type() and sci_is_fifo_type()
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://patch.msgid.link/20251129164325.209213-13-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rename port SCI_PORT_RSCI->RSCI_PORT_SCIF16 to differentiate it from
RZ/G3E port that has 32-stage FIFO.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://patch.msgid.link/20251129164325.209213-12-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add sci_is_rsci_type() for RSCI port type. This will simplify the code
when the support added for RSCI_PORT_SCIF32 private PORT type.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://patch.msgid.link/20251129164325.209213-11-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace devm_*_get_exclusive()->devm_*_array_get_exclusive() to support
existing SoCs along with RZ/G3E as RZ/G3E has 2 resets.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://patch.msgid.link/20251129164325.209213-10-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Shorten the number lines in sci_init_clocks() by fitting the error
messages within an 100-character length limit.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://patch.msgid.link/20251129164325.209213-7-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop rsci_clear_SCxSR by reusing rsci_clear_CFC() as the contents of
both functions are the same.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://patch.msgid.link/20251129164325.209213-6-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ports that support FIFO has fifosize > 1. Replace checking the port type
with fifosize for device file{create, remove}.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://patch.msgid.link/20251129164325.209213-5-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The rtrg variable is populated in sci_init_single() for RZ/T2H. Add
set_rtrg() callback for setting the rtrg value.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://patch.msgid.link/20251129164325.209213-4-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The RZ/T2H RSCI has 16-stage FIFO. Like other SoCs, set the default
rx_trigger as the fifosize.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://patch.msgid.link/20251129164325.209213-3-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify the probe() code by using dev_err_probe().
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Gerhard Engleder <eg@keba.com>
Link: https://patch.msgid.link/20251216193726.55449-4-gerhard@engleder-embedded.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add defines for better readability of the Indexed Control Register (ICR)
access. In enhanced mode SCR and LSR registers are used for ICR access.
The behavior of these register is different in this mode and that shall
be documented with dedicated defines.
Suggested-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Gerhard Engleder <eg@keba.com>
Link: https://patch.msgid.link/20251216193726.55449-3-gerhard@engleder-embedded.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andy and Ilpo suggested to add missing includes, because the code shall
not rely on indirect includes. Add missing includes and remove one
include, which only enabled indirect includes.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Suggested-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Gerhard Engleder <eg@keba.com>
Link: https://patch.msgid.link/20251216193726.55449-2-gerhard@engleder-embedded.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Z125 define is not used anywhere, thus removed. Also used a
more specific name for the maximum number of ports per unit and
removed the duplicated define MAX_PORTS
Reviewed-by: Jose Javier Rodriguez Barbarin <dev-josejavier.rodriguez@duagon.com>
Signed-off-by: Filip Jensen <dev-Felipe.Jensen@duagon.com>
Link: https://patch.msgid.link/20251210164804.94801-2-dev-Felipe.Jensen@duagon.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move pm_runtime_set_active() call earlier in probe to simplify error
handling and add proper error checking to ensure the device is marked
as active before any runtime PM operations can occur.
Additionally, replace the const struct dev_pm_ops declaration with
_DEFINE_DEV_PM_OPS macro for better consistency with modern kernel PM
patterns.
Signed-off-by: Artem Shimko <a.shimko.dev@gmail.com>
Link: https://patch.msgid.link/20251104145433.2316165-3-a.shimko.dev@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add error checking for clk_prepare_enable() calls in
dw8250_runtime_resume(). Currently if either clock fails to enable,
the function returns success while leaving clocks in inconsistent state.
This change implements comprehensive error handling by checking the return
values of both clk_prepare_enable() calls. If the second clock enable
operation fails after the first clock has already been successfully
enabled, the code now properly cleans up by disabling and unpreparing
the first clock before returning. The error code is then propagated to
the caller, ensuring that clock enable failures are properly reported
rather than being silently ignored.
Signed-off-by: Artem Shimko <a.shimko.dev@gmail.com>
Link: https://patch.msgid.link/20251104145433.2316165-2-a.shimko.dev@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of tty/serial driver changes for 6.19-rc1. Nothing
major at all, just small constant churn to make the tty layer "cleaner"
as well as serial driver updates and even a new test added! Included in
here are:
- More tty/serial cleanups from Jiri
- tty tiocsti test added to hopefully ensure we don't regress in this
area again
- sc16is7xx driver updates
- imx serial driver updates
- 8250 driver updates
- new hardware device ids added
- other minor serial/tty driver cleanups and tweaks
All of these have been in linux-next for a while with no reported issues
other than a merge-conflict that you will have when you merge into your
tree (should be simple to resolve, just delete the code on both sides
of the merge).
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCaTTJ+g8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymiEQCgweRHAivbv2avIlfsmpFewV27WMgAnR1aE5mW
JhhopcWcdjnRJikavHGo
=lhK0
-----END PGP SIGNATURE-----
Merge tag 'tty-6.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the big set of tty/serial driver changes for 6.19-rc1. Nothing
major at all, just small constant churn to make the tty layer
"cleaner" as well as serial driver updates and even a new test added!
Included in here are:
- More tty/serial cleanups from Jiri
- tty tiocsti test added to hopefully ensure we don't regress in this
area again
- sc16is7xx driver updates
- imx serial driver updates
- 8250 driver updates
- new hardware device ids added
- other minor serial/tty driver cleanups and tweaks
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-6.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (60 commits)
serial: sh-sci: Fix deadlock during RSCI FIFO overrun error
dt-bindings: serial: rsci: Drop "uart-has-rtscts: false"
LoongArch: dts: Add uart new compatible string
serial: 8250: Add Loongson uart driver support
dt-bindings: serial: 8250: Add Loongson uart compatible
serial: 8250: add driver for KEBA UART
serial: Keep rs485 settings for devices without firmware node
serial: qcom-geni: Enable Serial on SA8255p Qualcomm platforms
serial: qcom-geni: Enable PM runtime for serial driver
serial: sprd: Return -EPROBE_DEFER when uart clock is not ready
tty: serial: samsung: Declare earlycon for Exynos850
serial: icom: Convert PCIBIOS_* return codes to errnos
serial: 8250-of: Fix style issues in 8250_of.c
serial: add support of CPCI cards
serial: mux: Fix kernel doc for mux_poll()
tty: replace use of system_unbound_wq with system_dfl_wq
serial: 8250_platform: simplify IRQF_SHARED handling
serial: 8250: make share_irqs local to 8250_platform
serial: 8250: move skip_txen_test to core
serial: drop SERIAL_8250_DEPRECATED_OPTIONS
...
-----BEGIN PGP SIGNATURE-----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=qSzr
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.19-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Enable host bridge emulation for PCI_DOMAINS_GENERIC platforms (Dan
Williams)
- Switch vmd from custom domain number allocator to the common
allocator to prevent a potential race with new non-VMD buses (Dan
Williams)
- Enable Precision Time Measurement (PTM) only if device advertises
support for a relevant role, to prevent invalid PTM Requests that
cause ACS violations that are reported as AER Uncorrectable
Non-Fatal errors (Mika Westerberg)
Resource management:
- Prevent resource tree corruption when BAR resize fails (Ilpo
Järvinen)
- Restore BARs to the original size if a BAR resize fails (Ilpo
Järvinen)
- Remove BAR release from BAR resize attempts by the xe, i915, and
amdgpu drivers so the PCI core can restore BARs if the resize fails
(Ilpo Järvinen)
- Move Resizable BAR code to rebar.c (Ilpo Järvinen)
- Add pci_rebar_size_supported() and use it in i915 and xe (Ilpo
Järvinen)
- Add pci_rebar_get_max_size() and use it in xe and amdgpu (Ilpo
Järvinen)
Power management and error handling:
- For drivers using PCI legacy suspend, save config state at suspend
so that state (not any earlier state from enumeration, probe, or
error recovery) will be restored when resuming (Lukas Wunner)
- For devices with no driver or a driver that lacks power management,
save config state at hibernate so that state (not any earlier state
from enumeration, probe, or error recovery) will be restored when
resuming (Lukas Wunner)
- Save device config space on device addition, before driver binding,
so error recovery works more reliably (Lukas Wunner)
- Drop pci_save_state() from several drivers that no longer need it
since the PCI core always does it and pci_restore_state() no longer
invalidates the saved state (Lukas Wunner)
- Document use of pci_save_state() by drivers to capture the state
they want restored during error recovery (Lukas Wunner)
Power control:
- Add a struct pci_ops.assert_perst() function pointer to
assert/deassert PCIe PERST# and implement it for the qcom driver
(Krishna Chaitanya Chundru)
- Add DT binding and pwrctrl driver for the Toshiba TC9563 PCIe
switch, which must be held in reset after poweron so the pwrctrl
driver can configure the switch via I2C before bringing up the
links (Krishna Chaitanya Chundru)
Endpoint framework:
- Convert the endpoint doorbell test to use a threaded IRQ to fix a
'sleeping while atomic' issue (Bhanu Seshu Kumar Valluri)
- Add endpoint VNTB MSI doorbell support to reduce latency between
host and endpoint (Frank Li)
New native PCIe controller drivers:
- Add CIX Sky1 host controller DT binding and driver (Hans Zhang)
- Add NXP S32G host controller DT binding and driver (Vincent
Guittot)
- Add Renesas RZ/G3S host controller DT binding and driver (Claudiu
Beznea)
- Add SpacemiT K1 host controller DT binding and driver (Alex Elder)
Amlogic Meson PCIe controller driver:
- Update DT binding to name DBI region 'dbi', not 'elbi', and update
driver to support both (Manivannan Sadhasivam)
Apple PCIe controller driver:
- Move struct pci_host_bridge allocation from pci_host_common_init()
to callers, which significantly simplifies pcie-apple (Marc
Zyngier)
Broadcom STB PCIe controller driver:
- Disable advertising ASPM L0s support correctly (Jim Quinlan)
- Add a panic/die handler to print diagnostic info in case PCIe
caused an unrecoverable abort (Jim Quinlan)
Cadence PCIe controller driver:
- Add module support for Cadence platform host and endpoint
controller driver (Manikandan K Pillai)
- Split headers into 'legacy' (LGA) and 'high perf' (HPA) to prepare
for new CIX Sky1 driver (Manikandan K Pillai)
MediaTek PCIe controller driver:
- Convert DT binding to YAML schema (Christian Marangi)
- Add Airoha AN7583 DT compatible and driver support (Christian
Marangi)
Qualcomm PCIe controller driver:
- Add Qualcomm Kaanapali to SM8550 DT binding (Qiang Yu)
- Add required 'power-domains' and 'resets' to qcom sa8775p, sc7280,
sc8280xp, sm8150, sm8250, sm8350, sm8450, sm8550, x1e80100 DT
schemas (Krzysztof Kozlowski)
- Look up OPP using both frequency and data rate (not just frequency)
so RPMh votes can account for both (Krishna Chaitanya Chundru)
Rockchip DesignWare PCIe controller driver:
- Add Rockchip RK3528 compatible strings in DT binding (Yao Zi)
STMicroelectronics STM32MP25 PCIe controller driver:
- Fix a race between link training and endpoint register
initialization (Christian Bruel)
- Align endpoint allocations to match the ATU requirements (Christian
Bruel)
Synopsys DesignWare PCIe controller driver:
- Clear L1 PM Substate Capability 'Supported' bits unless glue driver
says it's supported, which prevents users from enabling non-working
L1SS. Currently only qcom and tegra194 support L1SS (Bjorn Helgaas)
- Remove now-superfluous L1SS disable code from tegra194 (Bjorn
Helgaas)
- Configure L1SS support in dw-rockchip when DT says
'supports-clkreq' (Shawn Lin)
TI Keystone PCIe controller driver:
- Fail the probe instead of silently succeeding if ks_pcie_of_data
didn't specify Root Complex or Endpoint mode (Siddharth Vadapalli)
- Make keystone buildable as a loadable module, except on ARM32 where
hook_fault_code() is __init (Siddharth Vadapalli)"
* tag 'pci-v6.19-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (100 commits)
MAINTAINERS: Add Manivannan Sadhasivam as PCI/pwrctrl maintainer
MAINTAINERS: Add CIX Sky1 PCIe controller driver maintainer
PCI: sky1: Add PCIe host support for CIX Sky1
dt-bindings: PCI: Add CIX Sky1 PCIe Root Complex bindings
PCI: cadence: Add support for High Perf Architecture (HPA) controller
MAINTAINERS: Add NXP S32G PCIe controller driver maintainer
PCI: s32g: Add NXP S32G PCIe controller driver (RC)
PCI: dwc: Add register and bitfield definitions
dt-bindings: PCI: s32g: Add NXP S32G PCIe controller
PCI: Add Renesas RZ/G3S host controller driver
PCI: host-generic: Move bridge allocation outside of pci_host_common_init()
dt-bindings: PCI: Add Renesas RZ/G3S PCIe controller binding
PCI: Validate pci_rebar_size_supported() input
Documentation: PCI: Amend error recovery doc with pci_save_state() rules
treewide: Drop pci_save_state() after pci_restore_state()
PCI/ERR: Ensure error recoverability at all times
PCI/PM: Stop needlessly clearing state_saved on enumeration and thaw
PCI/PM: Reinstate clearing state_saved in legacy and !PM codepaths
PCI: dw-rockchip: Configure L1SS support
PCI: tegra194: Remove unnecessary L1SS disable code
...
-----BEGIN PGP SIGNATURE-----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=FnfO
-----END PGP SIGNATURE-----
Merge tag 'printk-for-6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux
Pull printk updates from Petr Mladek:
- Allow creaing nbcon console drivers with an unsafe write_atomic()
callback that can only be called by the final nbcon_atomic_flush_unsafe().
Otherwise, the driver would rely on the kthread.
It is going to be used as the-best-effort approach for an
experimental nbcon netconsole driver, see
https://lore.kernel.org/r/20251121-nbcon-v1-2-503d17b2b4af@debian.org
Note that a safe .write_atomic() callback is supposed to work in NMI
context. But some networking drivers are not safe even in IRQ
context:
https://lore.kernel.org/r/oc46gdpmmlly5o44obvmoatfqo5bhpgv7pabpvb6sjuqioymcg@gjsma3ghoz35
In an ideal world, all networking drivers would be fixed first and
the atomic flush would be blocked only in NMI context. But it brings
the question how reliable networking drivers are when the system is
in a bad state. They might block flushing more reliable serial
consoles which are more suitable for serious debugging anyway.
- Allow to use the last 4 bytes of the printk ring buffer.
- Prevent queuing IRQ work and block printk kthreads when consoles are
suspended. Otherwise, they create non-necessary churn or even block
the suspend.
- Release console_lock() between each record in the kthread used for
legacy consoles on RT. It might significantly speed up the boot.
- Release nbcon context between each record in the atomic flush. It
prevents stalls of the related printk kthread after it has lost the
ownership in the middle of a record
- Add support for NBCON consoles into KDB
- Add %ptsP modifier for printing struct timespec64 and use it where
possible
- Misc code clean up
* tag 'printk-for-6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux: (48 commits)
printk: Use console_is_usable on console_unblank
arch: um: kmsg_dump: Use console_is_usable
drivers: serial: kgdboc: Drop checks for CON_ENABLED and CON_BOOT
lib/vsprintf: Unify FORMAT_STATE_NUM handlers
printk: Avoid irq_work for printk_deferred() on suspend
printk: Avoid scheduling irq_work on suspend
printk: Allow printk_trigger_flush() to flush all types
tracing: Switch to use %ptSp
scsi: snic: Switch to use %ptSp
scsi: fnic: Switch to use %ptSp
s390/dasd: Switch to use %ptSp
ptp: ocp: Switch to use %ptSp
pps: Switch to use %ptSp
PCI: epf-test: Switch to use %ptSp
net: dsa: sja1105: Switch to use %ptSp
mmc: mmc_test: Switch to use %ptSp
media: av7110: Switch to use %ptSp
ipmi: Switch to use %ptSp
igb: Switch to use %ptSp
e1000e: Switch to use %ptSp
...
- klp-build livepatch module generation (Josh Poimboeuf)
Introduce new objtool features and a klp-build
script to generate livepatch modules using a
source .patch as input.
This builds on concepts from the longstanding out-of-tree
kpatch project which began in 2012 and has been used for
many years to generate livepatch modules for production kernels.
However, this is a complete rewrite which incorporates
hard-earned lessons from 12+ years of maintaining kpatch.
Key improvements compared to kpatch-build:
- Integrated with objtool: Leverages objtool's existing control-flow
graph analysis to help detect changed functions.
- Works on vmlinux.o: Supports late-linked objects, making it
compatible with LTO, IBT, and similar.
- Simplified code base: ~3k fewer lines of code.
- Upstream: No more out-of-tree #ifdef hacks, far less cruft.
- Cleaner internals: Vastly simplified logic for symbol/section/reloc
inclusion and special section extraction.
- Robust __LINE__ macro handling: Avoids false positive binary diffs
caused by the __LINE__ macro by introducing a fix-patch-lines script
which injects #line directives into the source .patch to preserve
the original line numbers at compile time.
- Disassemble code with libopcodes instead of running objdump
(Alexandre Chartre)
- Disassemble support (-d option to objtool) by Alexandre Chartre,
which supports the decoding of various Linux kernel code generation
specials such as alternatives:
17ef: sched_balance_find_dst_group+0x62f mov 0x34(%r9),%edx
17f3: sched_balance_find_dst_group+0x633 | <alternative.17f3> | X86_FEATURE_POPCNT
17f3: sched_balance_find_dst_group+0x633 | call 0x17f8 <__sw_hweight64> | popcnt %rdi,%rax
17f8: sched_balance_find_dst_group+0x638 cmp %eax,%edx
... jump table alternatives:
1895: sched_use_asym_prio+0x5 test $0x8,%ch
1898: sched_use_asym_prio+0x8 je 0x18a9 <sched_use_asym_prio+0x19>
189a: sched_use_asym_prio+0xa | <jump_table.189a> | JUMP
189a: sched_use_asym_prio+0xa | jmp 0x18ae <sched_use_asym_prio+0x1e> | nop2
189c: sched_use_asym_prio+0xc mov $0x1,%eax
18a1: sched_use_asym_prio+0x11 and $0x80,%ecx
... exception table alternatives:
native_read_msr:
5b80: native_read_msr+0x0 mov %edi,%ecx
5b82: native_read_msr+0x2 | <ex_table.5b82> | EXCEPTION
5b82: native_read_msr+0x2 | rdmsr | resume at 0x5b84 <native_read_msr+0x4>
5b84: native_read_msr+0x4 shl $0x20,%rdx
.... x86 feature flag decoding (also see the X86_FEATURE_POPCNT
example in sched_balance_find_dst_group() above):
2faaf: start_thread_common.constprop.0+0x1f jne 0x2fba4 <start_thread_common.constprop.0+0x114>
2fab5: start_thread_common.constprop.0+0x25 | <alternative.2fab5> | X86_FEATURE_ALWAYS | X86_BUG_NULL_SEG
2fab5: start_thread_common.constprop.0+0x25 | jmp 0x2faba <.altinstr_aux+0x2f4> | jmp 0x4b0 <start_thread_common.constprop.0+0x3f> | nop5
2faba: start_thread_common.constprop.0+0x2a mov $0x2b,%eax
... NOP sequence shortening:
1048e2: snapshot_write_finalize+0xc2 je 0x104917 <snapshot_write_finalize+0xf7>
1048e4: snapshot_write_finalize+0xc4 nop6
1048ea: snapshot_write_finalize+0xca nop11
1048f5: snapshot_write_finalize+0xd5 nop11
104900: snapshot_write_finalize+0xe0 mov %rax,%rcx
104903: snapshot_write_finalize+0xe3 mov 0x10(%rdx),%rax
... and much more.
- Function validation tracing support (Alexandre Chartre)
- Various -ffunction-sections fixes (Josh Poimboeuf)
- Clang AutoFDO (Automated Feedback-Directed Optimizations) support (Josh Poimboeuf)
- Misc fixes and cleanups (Borislav Petkov, Chen Ni,
Dylan Hatch, Ingo Molnar, John Wang, Josh Poimboeuf,
Pankaj Raghav, Peter Zijlstra, Thorsten Blum)
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=yPrS
-----END PGP SIGNATURE-----
Merge tag 'objtool-core-2025-12-01' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull objtool updates from Ingo Molnar:
- klp-build livepatch module generation (Josh Poimboeuf)
Introduce new objtool features and a klp-build script to generate
livepatch modules using a source .patch as input.
This builds on concepts from the longstanding out-of-tree kpatch
project which began in 2012 and has been used for many years to
generate livepatch modules for production kernels. However, this is a
complete rewrite which incorporates hard-earned lessons from 12+
years of maintaining kpatch.
Key improvements compared to kpatch-build:
- Integrated with objtool: Leverages objtool's existing control-flow
graph analysis to help detect changed functions.
- Works on vmlinux.o: Supports late-linked objects, making it
compatible with LTO, IBT, and similar.
- Simplified code base: ~3k fewer lines of code.
- Upstream: No more out-of-tree #ifdef hacks, far less cruft.
- Cleaner internals: Vastly simplified logic for
symbol/section/reloc inclusion and special section extraction.
- Robust __LINE__ macro handling: Avoids false positive binary diffs
caused by the __LINE__ macro by introducing a fix-patch-lines
script which injects #line directives into the source .patch to
preserve the original line numbers at compile time.
- Disassemble code with libopcodes instead of running objdump
(Alexandre Chartre)
- Disassemble support (-d option to objtool) by Alexandre Chartre,
which supports the decoding of various Linux kernel code generation
specials such as alternatives:
17ef: sched_balance_find_dst_group+0x62f mov 0x34(%r9),%edx
17f3: sched_balance_find_dst_group+0x633 | <alternative.17f3> | X86_FEATURE_POPCNT
17f3: sched_balance_find_dst_group+0x633 | call 0x17f8 <__sw_hweight64> | popcnt %rdi,%rax
17f8: sched_balance_find_dst_group+0x638 cmp %eax,%edx
... jump table alternatives:
1895: sched_use_asym_prio+0x5 test $0x8,%ch
1898: sched_use_asym_prio+0x8 je 0x18a9 <sched_use_asym_prio+0x19>
189a: sched_use_asym_prio+0xa | <jump_table.189a> | JUMP
189a: sched_use_asym_prio+0xa | jmp 0x18ae <sched_use_asym_prio+0x1e> | nop2
189c: sched_use_asym_prio+0xc mov $0x1,%eax
18a1: sched_use_asym_prio+0x11 and $0x80,%ecx
... exception table alternatives:
native_read_msr:
5b80: native_read_msr+0x0 mov %edi,%ecx
5b82: native_read_msr+0x2 | <ex_table.5b82> | EXCEPTION
5b82: native_read_msr+0x2 | rdmsr | resume at 0x5b84 <native_read_msr+0x4>
5b84: native_read_msr+0x4 shl $0x20,%rdx
.... x86 feature flag decoding (also see the X86_FEATURE_POPCNT
example in sched_balance_find_dst_group() above):
2faaf: start_thread_common.constprop.0+0x1f jne 0x2fba4 <start_thread_common.constprop.0+0x114>
2fab5: start_thread_common.constprop.0+0x25 | <alternative.2fab5> | X86_FEATURE_ALWAYS | X86_BUG_NULL_SEG
2fab5: start_thread_common.constprop.0+0x25 | jmp 0x2faba <.altinstr_aux+0x2f4> | jmp 0x4b0 <start_thread_common.constprop.0+0x3f> | nop5
2faba: start_thread_common.constprop.0+0x2a mov $0x2b,%eax
... NOP sequence shortening:
1048e2: snapshot_write_finalize+0xc2 je 0x104917 <snapshot_write_finalize+0xf7>
1048e4: snapshot_write_finalize+0xc4 nop6
1048ea: snapshot_write_finalize+0xca nop11
1048f5: snapshot_write_finalize+0xd5 nop11
104900: snapshot_write_finalize+0xe0 mov %rax,%rcx
104903: snapshot_write_finalize+0xe3 mov 0x10(%rdx),%rax
... and much more.
- Function validation tracing support (Alexandre Chartre)
- Various -ffunction-sections fixes (Josh Poimboeuf)
- Clang AutoFDO (Automated Feedback-Directed Optimizations) support
(Josh Poimboeuf)
- Misc fixes and cleanups (Borislav Petkov, Chen Ni, Dylan Hatch, Ingo
Molnar, John Wang, Josh Poimboeuf, Pankaj Raghav, Peter Zijlstra,
Thorsten Blum)
* tag 'objtool-core-2025-12-01' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (129 commits)
objtool: Fix segfault on unknown alternatives
objtool: Build with disassembly can fail when including bdf.h
objtool: Trim trailing NOPs in alternative
objtool: Add wide output for disassembly
objtool: Compact output for alternatives with one instruction
objtool: Improve naming of group alternatives
objtool: Add Function to get the name of a CPU feature
objtool: Provide access to feature and flags of group alternatives
objtool: Fix address references in alternatives
objtool: Disassemble jump table alternatives
objtool: Disassemble exception table alternatives
objtool: Print addresses with alternative instructions
objtool: Disassemble group alternatives
objtool: Print headers for alternatives
objtool: Preserve alternatives order
objtool: Add the --disas=<function-pattern> action
objtool: Do not validate IBT for .return_sites and .call_sites
objtool: Improve tracing of alternative instructions
objtool: Add functions to better name alternatives
objtool: Identify the different types of alternatives
...
The original code tried to find a console that has CON_BOOT _or_
CON_ENABLED flag set. The flag CON_ENABLED is set to all registered
consoles, so in this case this check is always true, even for the
CON_BOOT consoles.
The initial intent of the kgdboc_earlycon_init was to get a console
early (CON_BOOT) or later on in the process (CON_ENABLED). The
code was using for_each_console macro, meaning that all console structs
were previously registered on the printk() machinery. At this point,
any console found on for_each_console is safe for kgdboc_earlycon_init
to use.
Dropping the check makes the code cleaner, and avoids further confusion
by future readers of the code.
Signed-off-by: Marcos Paulo de Souza <mpdesouza@suse.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Link: https://patch.msgid.link/20251121-printk-cleanup-part2-v2-1-57b8b78647f4@suse.com
Signed-off-by: Petr Mladek <pmladek@suse.com>
Depmod fails for a kernel made with:
make allnoconfig
echo -e "CONFIG_MODULES=y\nCONFIG_SERIAL_8250=m\nCONFIG_SERIAL_8250_EXTENDED=y\nCONFIG_SERIAL_8250_RSA=y" >> .config
make olddefconfig
...due to a dependency loop:
depmod: ERROR: Cycle detected: 8250 -> 8250_base -> 8250
depmod: ERROR: Found 2 modules in dependency cycles!
This is caused by the move of 8250 RSA code from 8250_port.c (in
8250_base.ko) into 8250_rsa.c (in 8250.ko) by the commit 5a128fb475
("serial: 8250: move RSA functions to 8250_rsa.c"). The commit
b20d6576cd ("serial: 8250: export RSA functions") tried to fix a
missing symbol issue with EXPORTs but those then cause this dependency
cycle.
Break dependency loop by moving 8250_rsa.o from 8250.ko to 8250_base.ko
and by passing univ8250_port_base_ops to univ8250_rsa_support() that
can make a local copy of it.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: Alex Davis <alex47794@gmail.com>
Fixes: 5a128fb475 ("serial: 8250: move RSA functions to 8250_rsa.c")
Fixes: b20d6576cd ("serial: 8250: export RSA functions")
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/all/87frc3sd8d.fsf@posteo.net/
Link: https://lore.kernel.org/all/CADiockCvM6v+d+UoFZpJSMoLAdpy99_h-hJdzUsdfaWGn3W7-g@mail.gmail.com/
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://patch.msgid.link/20251110105043.4062-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On RSCI IP, a deadlock occurs during a FIFO overrun error, as it uses a
different register to clear the FIFO overrun error status.
Cc: stable@kernel.org
Fixes: 0666e3fe95 ("serial: sh-sci: Add support for RZ/T2H SCI")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251114101350.106699-3-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the driver for on-chip UART used on Loongson family chips.
The hardware is similar to NS16550A, but there are the following
differences:
- Some chips (such as Loongson-2K2000) have added a fractional division
register to obtain the required baud rate accurately, so the
{get,set}_divisor callback is overridden.
- Due to hardware defects, quirk handling is required for
UART_MCR/UART_MSR.
Co-developed-by: Haowei Zheng <zhenghaowei@loongson.cn>
Signed-off-by: Haowei Zheng <zhenghaowei@loongson.cn>
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Reviewed-by: Huacai Chen <chenhuacai@loongson.cn>
Link: https://patch.msgid.link/2c2a01a276b9250efea0c7aa190efecdfd6fdf5a.1760166651.git.zhoubinbin@loongson.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The KEBA UART is found in the system FPGA of KEBA PLC devices. It is
mostly 8250 compatible with extension for some UART modes.
3 different variants exist. The simpliest variant supports only RS-232
and is used for debug interfaces. The next variant supports only RS-485
and is used mostly for communication with KEBA panel devices. The third
variant is able to support RS-232, RS-485 and RS-422. For this variant
not only the mode of the UART is configured, also the physics and
transceivers are switched according to the mode.
Signed-off-by: Gerhard Engleder <eg@keba.com>
Tested-by: Daniel Gierlinger <gida@keba.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Link: https://patch.msgid.link/20251023151229.11774-3-gerhard@engleder-embedded.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit fe7f0fa43c ("serial: 8250: Support rs485 devicetree properties")
retrieves rs485 properties for 8250 drivers. These properties are read
from the firmware node of the device within uart_get_rs485_mode(). If the
firmware node does not exist, then the rs485 flags are still reset. Thus,
8250 driver cannot set rs485 flags to enable a defined rs485 mode during
driver loading. This is no problem so far, as no 8250 driver sets the
rs485 flags.
The default rs485 mode can also be set by firmware nodes. But for some
devices a firmware node does not exist. E.g., for a PCIe based serial
interface on x86 no device tree is available and the ACPI information of
the BIOS often cannot by modified. In this case it shall be possible,
that a driver works out of the box by setting a reasonable default rs485
mode.
If no firmware node exists, then it should be possible for the driver to
set a reasonable default rs485 mode. Therefore, reset rs485 flags only
if a firmware node exists.
Signed-off-by: Gerhard Engleder <eg@keba.com>
Cc: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Link: https://patch.msgid.link/20251023151229.11774-2-gerhard@engleder-embedded.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Qualcomm automotive SA8255p SoC relies on firmware to configure
platform resources, including clocks, interconnects and TLMM.
The driver requests resources operations over SCMI using power
and performance protocols.
The SCMI power protocol enables or disables resources like clocks,
interconnect paths, and TLMM (GPIOs) using runtime PM framework APIs,
such as resume/suspend, to control power states(on/off).
The SCMI performance protocol manages UART baud rates, with each baud
rate represented by a performance level. The driver uses the
dev_pm_opp_set_level() API to request the desired baud rate by
specifying the performance level.
Signed-off-by: Praveen Talari <praveen.talari@oss.qualcomm.com>
Link: https://patch.msgid.link/20251110101043.2108414-5-praveen.talari@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The GENI serial driver currently handles power resource management
through calls to the statically defined geni_serial_resources_on() and
geni_serial_resources_off() functions. This approach reduces modularity
and limits support for platforms with diverse power management
mechanisms, including resource managed by firmware.
Improve modularity and enable better integration with platform-specific
power management, introduce support for runtime PM. Use
pm_runtime_resume_and_get() and pm_runtime_put_sync() within the
qcom_geni_serial_pm() callback to control resource power state
transitions based on UART power state changes.
Signed-off-by: Praveen Talari <praveen.talari@oss.qualcomm.com>
Link: https://patch.msgid.link/20251110101043.2108414-4-praveen.talari@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In sprd_clk_init(), when devm_clk_get() returns -EPROBE_DEFER
for either uart or source clock, we should propagate the
error instead of just warning and continuing with NULL clocks.
Currently the driver only emits a warning when clock acquisition
fails and proceeds with NULL clock pointers. This can lead to
issues later when the clocks are actually needed. More importantly,
when the clock provider is not ready yet and returns -EPROBE_DEFER,
we should return this error to allow deferred probing.
This change adds explicit checks for -EPROBE_DEFER after both:
1. devm_clk_get(uport->dev, uart)
2. devm_clk_get(uport->dev, source)
When -EPROBE_DEFER is encountered, the function now returns
-EPROBE_DEFER to let the driver framework retry probing
later when the clock dependencies are resolved.
Signed-off-by: Wenhua Lin <Wenhua.Lin@unisoc.com>
Link: https://patch.msgid.link/20251022030840.956589-1-Wenhua.Lin@unisoc.com
Reviewed-by: Cixi Geng <cixi.geng@linux.dev>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It makes it possible to use just "earlycon" param in kernel cmdline
on Exynos850 based boards instead of "earlycon=exynos4210,0x13820000",
as described in [1]:
When used with no options, the early console is determined by
stdout-path property in device tree's chosen node
[1] Documentation/admin-guide/kernel-parameters.txt
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://patch.msgid.link/20251118024822.28148-1-semen.protsenko@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
icom_probe() uses pci_read_config_dword() that returns PCIBIOS_*
codes. The return code is returned from the probe function as is but
probe functions should return normal errnos. A proper implementation
can be found in drivers/leds/leds-ss4200.c
Convert PCIBIOS_* return codes using pcibios_err_to_errno() into
normal errno before returning them.
Signed-off-by: Haotian Zhang <vulab@iscas.ac.cn>
Link: https://patch.msgid.link/20251117040710.1544-1-vulab@iscas.ac.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch resolves the warning "sizeof *port should be sizeof(*port)"
detected by checkpatch.pl.
Signed-off-by: jempty.liang <imntjempty@163.com>
Link: https://patch.msgid.link/20251117034117.55588-1-imntjempty@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Addi-Data GmbH is manufacturing multi-serial ports cards supporting CompactPCI (known as CPCI).
Those cards are identified with different DeviceIds. Those cards integrating standard UARTs
work the same way as PCI/PCIe models already supported in the serial driver.
Signed-off-by: Magne Bruno <magne.bruno@addi-data.com>
Link: https://patch.msgid.link/20251110162456.341029-1-magne.bruno@addi-data.com
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The validator is not happy:
Warning: drivers/tty/serial/mux.c:351 expecting prototype for mux_drv_poll(). Prototype was for mux_poll() instead
Update the kernel-doc accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20251106113815.2302539-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently if a user enqueue a work item using schedule_delayed_work() the
used wq is "system_wq" (per-cpu wq) while queue_delayed_work() use
WORK_CPU_UNBOUND (used when a cpu is not specified). The same applies to
schedule_work() that is using system_wq and queue_work(), that makes use
again of WORK_CPU_UNBOUND.
This lack of consistentcy cannot be addressed without refactoring the API.
This patch continues the effort to refactor worqueue APIs, which has begun
with the change introducing new workqueues and a new alloc_workqueue flag:
commit 128ea9f6cc ("workqueue: Add system_percpu_wq and system_dfl_wq")
commit 930c2ea566 ("workqueue: Add new WQ_PERCPU flag")
system_dfl_wq should be the default workqueue so as not to enforce
locality constraints for random work whenever it's not required.
The old system_unbound_wq will be kept for a few release cycles.
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Marco Crivellari <marco.crivellari@suse.com>
Link: https://patch.msgid.link/20251104105446.110884-1-marco.crivellari@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In 2009, commit c82f63e411 ("PCI: check saved state before restore")
changed the behavior of pci_restore_state() such that it became necessary
to call pci_save_state() afterwards, lest recovery from subsequent PCI
errors fails.
The commit has just been reverted and so all the pci_save_state() after
pci_restore_state() calls that have accumulated in the tree are now
superfluous. Drop them.
Two drivers chose a different approach to achieve the same result:
drivers/scsi/ipr.c and drivers/net/ethernet/intel/e1000e/netdev.c set the
pci_dev's "state_saved" flag to true before calling pci_restore_state().
Drop this as well.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com> # qat
Link: https://patch.msgid.link/c2b28cc4defa1b743cf1dedee23c455be98b397a.1760274044.git.lukas@wunner.de
IRQF_SHARED is the only flag handled in __serial8250_isa_init_ports()
and serial8250_probe_platform(). There is no need to precompute the
flags. Instead, initialize port->irqflags directly in the for loop.
Note the "if (bool)" is cheap and these are not hot paths anyway.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://patch.msgid.link/20251119092457.826789-7-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
8250_core is the only place where skip_txen_test is used. And platform
and core end up in 8250.ko, so there is no change in module name (param
prefix). Therefore, move skip_txen_test there and make it local.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://patch.msgid.link/20251119092457.826789-5-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In 3.7, 8250 was unintentionally renamed to 8250_core. This happened in
the commit 835d844d1a (8250_pnp: do pnp probe before legacy probe).
This made 8250.<xxxx> module options effectively defunct. Instead,
8250_core.<xxxx> worked.
In 3.9, the commit f2b8dfd9e4 (serial: 8250: Keep 8250.<xxxx> module
options functional after driver rename) made the original options work
again by introducing a hack.
Later in 3.9, the commit 9196d8acd7 (TTY: 8250, revert module name
change) changed the module name back to 8250 (from 8250_core). Since
then, the hack was there to support the transient 8250_core.<xxxx>
options. Those were present only in the 3.7..3.9 range.
These transient options were deprecated by 9326b047e4 (TTY: 8250,
deprecated 8250_core.* options) in v3.9 too.
Now, after those 12 years, it is time to get rid of this hack
completely.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://patch.msgid.link/20251119092457.826789-4-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Provided the uart driver is available globally, there is no need to
store a pointer to it in struct cdns_uart. Instead, use the global
cdns_uart_uart_driver in the code directly.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Link: https://patch.msgid.link/20251119092457.826789-3-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use guards in the serial_core code. This improves readability, makes
error handling easier, and marks locked portions of code explicit. All
that while being sure the lock is unlocked.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://patch.msgid.link/20251119100140.830761-11-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Neither uart_do_autoconfig(), nor uart_wait_modem_status() can return
-ENOIOCTLCMD. The ENOIOCTLCMD checks are there to check if 'cmd' matched
against TIOCSERCONFIG, and TIOCMIWAIT respectively. (With 0 or error in
'ret', it does not matter.)
Therefore, the code can simply return from the TIOCSERCONFIG and
TIOCMIWAIT spots immediately.
To be more explicit, use 'if' instead of switch-case for those single
values.
And return without jumping to the 'out' label -- it can be removed too.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://patch.msgid.link/20251119100140.830761-10-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When compiled with -ffunction-sections (e.g., for LTO, livepatch, dead
code elimination, AutoFDO, or Propeller), the startup() function gets
compiled into the .text.startup section (or in some cases
.text.startup.constprop.0 or .text.startup.isra.0).
However, the .text.startup and .text.startup.* sections are also used by
the compiler for __attribute__((constructor)) code.
This naming conflict causes the vmlinux linker script to wrongly place
startup() function code in .init.text, which gets freed during boot.
Some builds have a mix of objects, both with and without
-ffunctions-sections, so it's not possible for the linker script to
disambiguate with #ifdef CONFIG_FUNCTION_SECTIONS or similar. This
means that "startup" unfortunately needs to be prohibited as a function
name.
Rename startup() to icom_startup(). For consistency, also rename its
shutdown() counterpart to icom_shutdown().
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://patch.msgid.link/1aee9ef69f9d40405676712b34f0c397706e7023.1763669451.git.jpoimboe@kernel.org
Inline the contents of sh-sci.h into sh-sci.c and remove the
header file. The header only contained register definitions
and macros used exclusively by the sh-sci driver, making the
separate header unnecessary.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://patch.msgid.link/20251023104313.210989-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check for returned DMA addresses using specialized dma_mapping_error()
helper which is generally recommended for this purpose by
Documentation/core-api/dma-api.rst:
"In some circumstances dma_map_single(), ...
will fail to create a mapping. A driver can check for these errors
by testing the returned DMA address with dma_mapping_error()."
Found via static analysis and this is similar to commit fa0308134d
("ALSA: memalloc: prefer dma_mapping_error() over explicit address checking")
Fixes: 58ac1b3799 ("ARM: PL011: Fix DMA support")
Cc: stable <stable@kernel.org>
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://patch.msgid.link/20251027092053.87937-1-linmq006@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Indicate why lock needs to be asserted when accessing
MSR register, as this is not immediately obvious when looking at this
register in the device datasheet.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20251027142957.1032073-15-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fold some multi-line comments into a single line, taking advantage of the
new 100 line length limit to improve readability and to have uniform style
across driver.
Add missing 's' to SC16IS7XX_MCR_TCRTLR_BIT registers comments.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20251027142957.1032073-14-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to redefine the driver name. Use KBUILD_MODNAME and get
rid of DRV_NAME altogether.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20251027142957.1032073-12-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify macro to_sc16is7xx_one() to only take one parameter, as most
of the time (19) it is called with the "port" structure name. This
improves readability.
For the remaining places where it is called (4), simply use container_of()
locally. This is similar to what is done in other drivers (ex: max310x).
For sc16is7xx_tx_proc(), first assigning "one" variable allows to simplify
"port" variable init.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20251027142957.1032073-10-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sc16is7xx_probe() function is very long. To improve readability, move
port/channel initialization to a separate function.
No functional change intended.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20251027142957.1032073-9-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SPR shares the same address space as TLR and XOFF2. If SPR or TLR were to
be used eventually, this could lead to incorrect read value from the cache.
Prevent this potential bug by declaring SPR/TLR/XOFF2 as volatile.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20251027142957.1032073-8-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Core already prints detailed error messages on ENOMEM errors and drivers
should avoid repeating it.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20251027142957.1032073-7-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Guards can help to make the code more readable, so use them wherever they
do so.
In sc16is7xx_port_irq(), labels and 'rc' locals are eliminated completely.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20251027142957.1032073-6-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to cast from a void * pointer, so remove this cast.
Also remove empty line inavertently added in commit d5078509c8
("serial: sc16is7xx: improve do/while loop in sc16is7xx_irq()") and
change variables order to follow reversed xmas tree.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20251027142957.1032073-5-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rename lock/unlock functions to make it more generic and applicable to both
the Enhanced register set and the Special register set.
Use this new generic function when accessing the Special register set in
sc16is7xx_set_baud(), and when accessing the Enhanced register set in
sc16is7xx_set_termios() and sc16is7xx_probe().
This helps readability and also avoid to make future mistakes when
accessing these obfuscated registers.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20251027142957.1032073-4-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This mutex is used as a lock when accessing registers that share the same
address space, not necessarily EFR registers.
For example, address 0x06 is shared by MSR, TCR and XOFF1 registers,
independently of EFR.
Rename the mutex with a more generic name to avoid misinterpreting its
usage.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20251027142957.1032073-3-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no reference to CONF_MODE_A or CONF_MODE_B in the manufacturer's
datasheet.
Rename register set configuration macros for the LCR register, to better
show their intended usage to select either the Special register set, or the
Enhanced register set.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20251027142957.1032073-2-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some MediaTek SoCs got a gated UART baud clock, which currently gets
disabled as the clk subsystem believes it would be unused. This results in
the uart freezing right after "clk: Disabling unused clocks" on those
platforms.
Request the baud clock to be prepared and enabled during probe, and to
restore run-time power management capabilities to what it was before commit
e32a83c70c ("serial: 8250-mtk: modify mtk uart power and clock
management") disable and unprepare the baud clock when suspending the UART,
prepare and enable it again when resuming it.
Fixes: e32a83c70c ("serial: 8250-mtk: modify mtk uart power and clock management")
Fixes: b6c7ff2693 ("serial: 8250_mtk: Simplify clock sequencing and runtime PM")
Cc: stable <stable@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://patch.msgid.link/de5197ccc31e1dab0965cabcc11ca92e67246cf6.1758058441.git.daniel@makrotopia.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check the return value of reset_control_deassert() in the probe
function to prevent continuing probe when reset deassertion fails.
Previously, reset_control_deassert() was called without checking its
return value, which could lead to probe continuing even when the
device reset wasn't properly deasserted.
The fix checks the return value and returns an error with dev_err_probe()
if reset deassertion fails, providing better error handling and
diagnostics.
Fixes: acbdad8dd1 ("serial: 8250_dw: simplify optional reset handling")
Cc: stable <stable@kernel.org>
Signed-off-by: Artem Shimko <a.shimko.dev@gmail.com>
Link: https://patch.msgid.link/20251019095131.252848-1-a.shimko.dev@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 43c51bb573 ("sc16is7xx: make sure device is in suspend once
probed") permanently enabled access to the enhanced features in
sc16is7xx_probe(), and it is never disabled after that.
Therefore, remove re-enable of enhanced features in
sc16is7xx_set_baud(). This eliminates a potential useless read + write
cycle each time the baud rate is reconfigured.
Fixes: 43c51bb573 ("sc16is7xx: make sure device is in suspend once probed")
Cc: stable <stable@kernel.org>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20251006142002.177475-1-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Advantech 2-port serial card with PCI vendor=0x13fe and device=0x0018
has a 'XR17V35X' chip installed on the circuit board. Therefore, this
driver can be used instead of theu outdated out-of-tree driver from the
manufacturer.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Cc: stable <stable@kernel.org>
Link: https://patch.msgid.link/20250924134115.2667650-1-fe@dev.tdt.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The receive error handling code is shared between RSCI and all other
SCIF port types, but the RSCI overrun_reg is specified as a memory
offset, while for other SCIF types it is an enum value used to index
into the sci_port_params->regs array, as mentioned above the
sci_serial_in() function.
For RSCI, the overrun_reg is CSR (0x48), causing the sci_getreg() call
inside the sci_handle_fifo_overrun() function to index outside the
bounds of the regs array, which currently has a size of 20, as specified
by SCI_NR_REGS.
Because of this, we end up accessing memory outside of RSCI's
rsci_port_params structure, which, when interpreted as a plat_sci_reg,
happens to have a non-zero size, causing the following WARN when
sci_serial_in() is called, as the accidental size does not match the
supported register sizes.
The existence of the overrun_reg needs to be checked because
SCIx_SH3_SCIF_REGTYPE has overrun_reg set to SCLSR, but SCLSR is not
present in the regs array.
Avoid calling sci_getreg() for port types which don't use standard
register handling.
Use the ops->read_reg() and ops->write_reg() functions to properly read
and write registers for RSCI, and change the type of the status variable
to accommodate the 32-bit CSR register.
sci_getreg() and sci_serial_in() are also called with overrun_reg in the
sci_mpxed_interrupt() interrupt handler, but that code path is not used
for RSCI, as it does not have a muxed interrupt.
------------[ cut here ]------------
Invalid register access
WARNING: CPU: 0 PID: 0 at drivers/tty/serial/sh-sci.c:522 sci_serial_in+0x38/0xac
Modules linked in: renesas_usbhs at24 rzt2h_adc industrialio_adc sha256 cfg80211 bluetooth ecdh_generic ecc rfkill fuse drm backlight ipv6
CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted 6.17.0-rc1+ #30 PREEMPT
Hardware name: Renesas RZ/T2H EVK Board based on r9a09g077m44 (DT)
pstate: 604000c5 (nZCv daIF +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : sci_serial_in+0x38/0xac
lr : sci_serial_in+0x38/0xac
sp : ffff800080003e80
x29: ffff800080003e80 x28: ffff800082195b80 x27: 000000000000000d
x26: ffff8000821956d0 x25: 0000000000000000 x24: ffff800082195b80
x23: ffff000180e0d800 x22: 0000000000000010 x21: 0000000000000000
x20: 0000000000000010 x19: ffff000180e72000 x18: 000000000000000a
x17: ffff8002bcee7000 x16: ffff800080000000 x15: 0720072007200720
x14: 0720072007200720 x13: 0720072007200720 x12: 0720072007200720
x11: 0000000000000058 x10: 0000000000000018 x9 : ffff8000821a6a48
x8 : 0000000000057fa8 x7 : 0000000000000406 x6 : ffff8000821fea48
x5 : ffff00033ef88408 x4 : ffff8002bcee7000 x3 : ffff800082195b80
x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffff800082195b80
Call trace:
sci_serial_in+0x38/0xac (P)
sci_handle_fifo_overrun.isra.0+0x70/0x134
sci_er_interrupt+0x50/0x39c
__handle_irq_event_percpu+0x48/0x140
handle_irq_event+0x44/0xb0
handle_fasteoi_irq+0xf4/0x1a0
handle_irq_desc+0x34/0x58
generic_handle_domain_irq+0x1c/0x28
gic_handle_irq+0x4c/0x140
call_on_irq_stack+0x30/0x48
do_interrupt_handler+0x80/0x84
el1_interrupt+0x34/0x68
el1h_64_irq_handler+0x18/0x24
el1h_64_irq+0x6c/0x70
default_idle_call+0x28/0x58 (P)
do_idle+0x1f8/0x250
cpu_startup_entry+0x34/0x3c
rest_init+0xd8/0xe0
console_on_rootfs+0x0/0x6c
__primary_switched+0x88/0x90
---[ end trace 0000000000000000 ]---
Cc: stable <stable@kernel.org>
Fixes: 0666e3fe95 ("serial: sh-sci: Add support for RZ/T2H SCI")
Signed-off-by: Cosmin Tanislav <cosmin-gabriel.tanislav.xa@renesas.com>
Link: https://patch.msgid.link/20250923154707.1089900-1-cosmin-gabriel.tanislav.xa@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the '8250_exar' module is loaded into the kernel, a kernel trace
with 'WARN_ON(legacy_iomap_table[bar])' is dumped to the console,
because the old pci table mapping is still used in '8250_pcilib'.
The old function have been deprecated in commit e354bb84a4 ("PCI:
Deprecate pcim_iomap_table(), pcim_iomap_regions_request_all()").
The remapping already takes or must take place in the driver that calls
the function 'serial8250_pci_setup_port()'. The remapping should only be
called once via 'pcim_iomap()'. Therefore the remapping moved to the
caller of 'serial8250_pci_setup_port()'.
To replace the outdated/legacy iomap_table processing in '8250_pcilib' the
function signature of 'serial8250_pci_setup_port()' has been extended with
an already iomapped address value. So this can be used directly without
io mapping again.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://patch.msgid.link/20250930072743.791580-1-fe@dev.tdt.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current imx uart wakeup event would not report itself as wakeup source
through sysfs. Add pm_wakeup_event() to support it.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20251002045259.2725461-3-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the i.MX UART driver enables wake-related registers for all
UART devices by default. However, this is unnecessary for devices that
are not configured as wakeup sources. To address this, add a
device_may_wakeup() check before configuring the UART wake-related
registers.
Fixes: db1a9b5500 ("tty: serial: imx: Allow UART to be a source for wakeup")
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20251002045259.2725461-2-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current lpuart wakeup event would not report itself as wakeup source
through sysfs. Add pm_wakeup_event() to support it.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20250924025607.2515833-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is a single driver fix for the qcom_geni_serial driver for
6.18-rc1. It has been in my tree for weeks, but missed being sent to
you for 6.17-final due to travel on my side.
This fixes a reported regression for this driver that prevents 6.17 from
working properly on this platform.
It has been in linux-next for many weeks with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCaOUQrA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymmXwCgj5hLg2MHRlvZ+aCD0K/S2Qt4eqEAn32POqfZ
UntJ9O23oHW1+RmAvBB7
=zKb3
-----END PGP SIGNATURE-----
Merge tag 'tty-6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty driver fix from Greg KH:
"Here is a single driver fix for the qcom_geni_serial driver. It has
been in my tree for weeks, but missed being sent to you for 6.17-final
due to travel on my side.
This fixes a reported regression for this driver that prevents 6.17
from working properly on this platform.
It has been in linux-next for many weeks with no reported issues"
* tag 'tty-6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: qcom-geni: Fix blocked task
Here are some small updates for tty/serial drivers for 6.18-rc1.
Not many changes overall, just the usual:
- abi cleanups and reworking of the tty functions by Jiri by adding
console lock guard logic
- 8250_platform driver updates
- qcom-geni driver updates
- other minor serial driver updates
- some more vt escape codes added
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCaOEnLA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymLswCfa2SDyet0vn5oIrto+0WG9Wxlp3AAoMaDzkqG
DX2YoOI1L0miAQfQ9IhZ
=0V8V
-----END PGP SIGNATURE-----
Merge tag 'tty-6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here are some small updates for tty/serial drivers for 6.18-rc1.
Not many changes overall, just the usual:
- abi cleanups and reworking of the tty functions by Jiri by adding
console lock guard logic
- 8250_platform driver updates
- qcom-geni driver updates
- other minor serial driver updates
- some more vt escape codes added
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (43 commits)
tty: serial: fix help message for SERIAL_CPM
serial: 8250: omap: Support wakeup pinctrl state on suspend
dt-bindings: serial: 8250_omap: Add wakeup pinctrl state
serial: max310x: improve interrupt handling
vt: move vc_saved_screen to within tty allocated judgment
Revert "m68k: make HPDCA and HPAPCI bools"
tty: remove redundant condition checks
tty/vt: Add missing return value for VT_RESIZE in vt_ioctl()
vt: remove redundant check on vc_mode in con_font_set()
serial: qcom-geni: Add DFS clock mode support to GENI UART driver
m68k: make HPDCA and HPAPCI bools
tty: n_gsm: Don't block input queue by waiting MSC
serial: qcom-geni: Fix off-by-one error in ida_alloc_range()
serdev: Drop dev_pm_domain_detach() call
serial: sc16is7xx: drop redundant conversion to bool
vt: add support for smput/rmput escape codes
serial: stm32: allow selecting console when the driver is module
serial: 8250_core: fix coding style issue
tty: serial: Modify the use of dev_err_probe()
s390/char/con3270: use tty_port_tty guard()
...
Lots of platform specific updates for Qualcomm SoCs, including a
new TEE subsystem driver for the Qualcomm QTEE firmware interface.
Added support for the Apple A11 SoC in drivers that are shared with the
M1/M2 series, among more updates for those.
Smaller platform specific driver updates for Renesas, ASpeed, Broadcom,
Nvidia, Mediatek, Amlogic, TI, Allwinner, and Freescale SoCs.
Driver updates in the cache controller, memory controller and reset
controller subsystems.
SCMI firmware updates to add more features and improve robustness.
This includes support for having multiple SCMI providers in a single
system.
TEE subsystem support for protected DMA-bufs, allowing hardware to
access memory areas that managed by the kernel but remain inaccessible
from the CPU in EL1/EL0.
-----BEGIN PGP SIGNATURE-----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=mcZR
-----END PGP SIGNATURE-----
Merge tag 'soc-drivers-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC driver updates from Arnd Bergmann:
"Lots of platform specific updates for Qualcomm SoCs, including a new
TEE subsystem driver for the Qualcomm QTEE firmware interface.
Added support for the Apple A11 SoC in drivers that are shared with
the M1/M2 series, among more updates for those.
Smaller platform specific driver updates for Renesas, ASpeed,
Broadcom, Nvidia, Mediatek, Amlogic, TI, Allwinner, and Freescale
SoCs.
Driver updates in the cache controller, memory controller and reset
controller subsystems.
SCMI firmware updates to add more features and improve robustness.
This includes support for having multiple SCMI providers in a single
system.
TEE subsystem support for protected DMA-bufs, allowing hardware to
access memory areas that managed by the kernel but remain inaccessible
from the CPU in EL1/EL0"
* tag 'soc-drivers-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (139 commits)
soc/fsl/qbman: Use for_each_online_cpu() instead of for_each_cpu()
soc: fsl: qe: Drop legacy-of-mm-gpiochip.h header from GPIO driver
soc: fsl: qe: Change GPIO driver to a proper platform driver
tee: fix register_shm_helper()
pmdomain: apple: Add "apple,t8103-pmgr-pwrstate"
dt-bindings: spmi: Add Apple A11 and T2 compatible
serial: qcom-geni: Load UART qup Firmware from linux side
spi: geni-qcom: Load spi qup Firmware from linux side
i2c: qcom-geni: Load i2c qup Firmware from linux side
soc: qcom: geni-se: Add support to load QUP SE Firmware via Linux subsystem
soc: qcom: geni-se: Cleanup register defines and update copyright
dt-bindings: qcom: se-common: Add QUP Peripheral-specific properties for I2C, SPI, and SERIAL bus
Documentation: tee: Add Qualcomm TEE driver
tee: qcom: enable TEE_IOC_SHM_ALLOC ioctl
tee: qcom: add primordial object
tee: add Qualcomm TEE driver
tee: increase TEE_MAX_ARG_SIZE to 4096
tee: add TEE_IOCTL_PARAM_ATTR_TYPE_OBJREF
tee: add TEE_IOCTL_PARAM_ATTR_TYPE_UBUF
tee: add close_context to TEE driver operation
...
Introduce support for loading firmware into the QUP serial engines from
Linux, which allows deferring selection of which protocol (uart, i2c,
spi, etc) a given SE should have until the OS loads.
Also introduce the "object invoke" interface in the SCM driver, to
provide interface to the Qualcomm TEE driver.
-----BEGIN PGP SIGNATURE-----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=TulG
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=JuVO
-----END PGP SIGNATURE-----
Merge tag 'qcom-drivers-for-6.18-2' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into soc/drivers
More Qualcomm device driver updates for v6.18
Introduce support for loading firmware into the QUP serial engines from
Linux, which allows deferring selection of which protocol (uart, i2c,
spi, etc) a given SE should have until the OS loads.
Also introduce the "object invoke" interface in the SCM driver, to
provide interface to the Qualcomm TEE driver.
* tag 'qcom-drivers-for-6.18-2' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
serial: qcom-geni: Load UART qup Firmware from linux side
spi: geni-qcom: Load spi qup Firmware from linux side
i2c: qcom-geni: Load i2c qup Firmware from linux side
soc: qcom: geni-se: Add support to load QUP SE Firmware via Linux subsystem
soc: qcom: geni-se: Cleanup register defines and update copyright
dt-bindings: qcom: se-common: Add QUP Peripheral-specific properties for I2C, SPI, and SERIAL bus
firmware: qcom: scm: add support for object invocation
firmware: qcom: tzmem: export shm_bridge create/delete
Link: https://lore.kernel.org/r/20250921020225.595403-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add provision to load firmware of Serial engine for UART protocol from
Linux Execution Environment on running on APPS processor.
Co-developed-by: Mukesh Kumar Savaliya <mukesh.savaliya@oss.qualcomm.com>
Signed-off-by: Mukesh Kumar Savaliya <mukesh.savaliya@oss.qualcomm.com>
Signed-off-by: Viken Dadhaniya <viken.dadhaniya@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250911043256.3523057-7-viken.dadhaniya@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Revert commit 1afa70632c ("serial: qcom-geni: Enable PM runtime for
serial driver") and its dependent commit 86fa39dd6f ("serial:
qcom-geni: Enable Serial on SA8255p Qualcomm platforms") because the
first one causes regression - hang task on Qualcomm RB1 board (QRB2210)
and unable to use serial at all during normal boot:
INFO: task kworker/u16:0:12 blocked for more than 42 seconds.
Not tainted 6.17.0-rc1-00004-g53e760d89498 #9
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:kworker/u16:0 state:D stack:0 pid:12 tgid:12 ppid:2 task_flags:0x4208060 flags:0x00000010
Workqueue: async async_run_entry_fn
Call trace:
__switch_to+0xe8/0x1a0 (T)
__schedule+0x290/0x7c0
schedule+0x34/0x118
rpm_resume+0x14c/0x66c
rpm_resume+0x2a4/0x66c
rpm_resume+0x2a4/0x66c
rpm_resume+0x2a4/0x66c
__pm_runtime_resume+0x50/0x9c
__driver_probe_device+0x58/0x120
driver_probe_device+0x3c/0x154
__driver_attach_async_helper+0x4c/0xc0
async_run_entry_fn+0x34/0xe0
process_one_work+0x148/0x290
worker_thread+0x2c4/0x3e0
kthread+0x118/0x1c0
ret_from_fork+0x10/0x20
The issue was reported on 12th of August and was ignored by author of
commits introducing issue for two weeks. Only after complaining author
produced a fix which did not work, so if original commits cannot be
reliably fixed for 5 weeks, they obviously are buggy and need to be
dropped.
Fixes: 1afa70632c ("serial: qcom-geni: Enable PM runtime for serial driver")
Reported-by: Alexey Klimov <alexey.klimov@linaro.org>
Closes: https://lore.kernel.org/all/DC0D53ZTNOBU.E8LSD5E5Z8TX@linaro.org/
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Alexey Klimov <alexey.klimov@linaro.org>
Reviewed-by: Alexey Klimov <alexey.klimov@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20250917010437.129912-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Running checkpatch reported error extra whitespace at the
end of help message for SERIAL_CPM menu entry
Signed-off-by: Arturs Artamonovs <Arturs.Artamonovs@analog.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This update includes:
- basic infrastructure support for Microchip LAN969x SoC
- SoC ARCH symbols (existing SparX-5, new LAN969x) under the
ARCH_MICROCHIP hidden symbol (already in use by AT91 in 6.17)
- addition of that new symbol for drivers that are shared by
Microchip SoC-s now and in the future
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQ5TRCVIBiyi/S+BG4fOrpwrNPNDAUCaMgFkQAKCRAfOrpwrNPN
DFEbAQDg6iMOzL+C2tqu9eTfBZv9DCKcbfVFeHnwGqSbH8L/WgD/ZOq4UKIBMXpA
MGtwDDkDKBPVv3clF461/nS+VtAOaAE=
=upTs
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=zZ1l
-----END PGP SIGNATURE-----
Merge tag 'microchip-soc-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into soc/drivers
Microchip ARM64 SoC updates for v6.18:
This update includes:
- basic infrastructure support for Microchip LAN969x SoC
- SoC ARCH symbols (existing SparX-5, new LAN969x) under the
ARCH_MICROCHIP hidden symbol (already in use by AT91 in 6.17)
- addition of that new symbol for drivers that are shared by
Microchip SoC-s now and in the future
* tag 'microchip-soc-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
crypto: atmel-aes: make it selectable for ARCH_MICROCHIP
char: hw_random: atmel: make it selectable for ARCH_MICROCHIP
i2c: at91: make it selectable for ARCH_MICROCHIP
spi: atmel: make it selectable for ARCH_MICROCHIP
tty: serial: atmel: make it selectable for ARCH_MICROCHIP
mfd: at91-usart: Make it selectable for ARCH_MICROCHIP
arm64: lan969x: Add support for Microchip LAN969x SoC
arm64: Add config for Microchip SoC platforms
Link: https://lore.kernel.org/r/20250915123548.13722-1-nicolas.ferre@microchip.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Here are some small tty and serial driver fixes for 6.17-rc6 that
resolve some reported problems. Included in here are:
- 8250 driver dt bindings fixes
- broadcom serial driver binding fixes
- hvc_console bugfix
- xilinx serial driver bugfix
- sc16is7xx serial driver bugfix
All of these have been in linux-next for the past week with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCaMar1w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yk8AQCgx9deB0WhbxP/+3sVJ+0swX/bWdoAn3hCCy8f
P+QkteZ02Mmz25DS+gMB
=3mTh
-----END PGP SIGNATURE-----
Merge tag 'tty-6.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some small tty and serial driver fixes for 6.17-rc6 that
resolve some reported problems. Included in here are:
- 8250 driver dt bindings fixes
- broadcom serial driver binding fixes
- hvc_console bugfix
- xilinx serial driver bugfix
- sc16is7xx serial driver bugfix
All of these have been in linux-next for the past week with no
reported issues"
* tag 'tty-6.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: xilinx_uartps: read reg size from DTS
tty: hvc_console: Call hvc_kick in hvc_write unconditionally
dt-bindings: serial: 8250: allow "main" and "uart" as clock names
dt-bindings: serial: 8250: move a constraint
dt-bindings: serial: brcm,bcm7271-uart: Constrain clocks
serial: sc16is7xx: fix bug in flow control levels init
UART can be used as a wakeup source for am62 from suspend to ram states.
To enable wakeup from UART am62 requires a wakeup flag being set in the
pinctrl.
If the device is marked as wakeup enabled, select the 'wakeup' pinctrl
state on suspend and restore the default pinctrl state on resume.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Signed-off-by: Kendall Willis <k-willis@ti.com>
Link: https://lore.kernel.org/r/20250910-uart-daisy-chain-8250-omap-v2-2-e90d44c1a9ac@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When there is a heavy load of receiving characters to all
four UART's, the warning 'Hardware RX FIFO overrun' is
sometimes detected.
The current implementation always service first the highest UART
until no more interrupt and then service another UART
(ex: UART3 will be serviced for as long as there are interrupts
for it, then UART2, etc).
This commit handle all individual interrupt sources before
reading the global IRQ register again.
This commit has also a nice side-effect of improving the efficiency
of the driver by reducing the number of reads of the global
IRQ register.
Signed-off-by: Tapio Reijonen <tapio.reijonen@vaisala.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Reviewed-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20250908-master-max310x-improve-interrupt-handling-v3-1-91985e82ba39@vaisala.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
LAN969x uses the Atmel USART serial, so make it selectable for
ARCH_MICROCHIP to avoid needing to update depends in future if other
Microchip SoC-s use it as well.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Current implementation uses `CDNS_UART_REGISTER_SPACE(0x1000)`
for request_mem_region() and ioremap() in cdns_uart_request_port() API.
The cadence/xilinx IP has register space defined from offset 0x0 to 0x48.
It also mentions that the register map is defined as [6:0]. So, the upper
region may/maynot be used based on the IP integration.
In Axiado AX3000 SoC two UART instances are defined
0x100 apart. That is creating issue in some other instance due to overlap
with addresses.
Since, this address space is already being defined in the
devicetree, use the same when requesting the register space.
Fixes: 1f70557790 ("arm64: dts: axiado: Add initial support for AX3000 SoC and eval board")
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Harshit Shah <hshah@axiado.com>
Link: https://lore.kernel.org/r/20250902-xilinx-uartps-reg-size-v3-1-d11cfa7258e3@axiado.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GENI UART driver currently supports only non-DFS (Dynamic Frequency
Scaling) mode for source frequency selection. However, to operate correctly
in DFS mode, the GENI SCLK register must be programmed with the appropriate
DFS index. Failing to do so can result in incorrect frequency selection
Add support for Dynamic Frequency Scaling (DFS) mode in the GENI UART
driver by configuring the GENI_CLK_SEL register with the appropriate DFS
index. This ensures correct frequency selection when operating in DFS mode.
Replace the UART driver-specific logic for clock selection with the GENI
common driver function to obtain the desired frequency and corresponding
clock index. This improves maintainability and consistency across
GENI-based drivers.
Signed-off-by: Viken Dadhaniya <viken.dadhaniya@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250903063136.3015237-1-viken.dadhaniya@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ida_alloc_range() function expects an inclusive range, meaning both
the start and end values are valid allocation targets. Passing nr_ports
as the upper bound allows allocation of an ID equal to nr_ports, which
is out of bounds when used as an index into the port array.
Fix this by subtracting 1 from nr_ports in both calls to ida_alloc_range(),
ensuring the allocated ID stays within the valid range
[start, nr_ports - 1].
This prevents potential out-of-bounds access when the allocated ID is used
as an index.
Fixes: 9391ab1ed9 ("serial: qcom-geni: Make UART port count configurable via Kconfig")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/r/202508180815.R2nDyajs-lkp@intel.com/
Signed-off-by: Zong Jiang <quic_zongjian@quicinc.com>
Link: https://lore.kernel.org/r/20250827120319.1682835-1-quic_zongjian@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The result of integer comparison already evaluates to bool. No need for
explicit conversion.
Signed-off-by: Xichao Zhao <zhao.xichao@vivo.com>
Link: https://lore.kernel.org/r/20250827024514.76149-1-zhao.xichao@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dev_err_probe() doesn't do anything when error is '-ENOMEM'.
Make the following two changes:
(1) Replace -ENOMEM with -ENOSPC in max3100_probe().
(2) Just return -ENOMEM instead in max310x_probe().
Signed-off-by: Xichao Zhao <zhao.xichao@vivo.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250819120927.607744-1-zhao.xichao@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Having all the new guards, use them in the 8250_rsa code. This improves
readability, makes error handling easier, and marks locked portions of
code explicit.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250814072456.182853-14-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Having all the new guards, use them in the 8250_omap code. This improves
readability, makes error handling easier, and marks locked portions of
code explicit.
For this to work, UART_CAP_RPM has to be set to up->capabilities a bit
earlier.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250814072456.182853-13-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To use guard()s easily in omap_8250_set_termios(), split it into atomic
and non-atomic part. The former can be easily guarded -- without a need
of indenting or moving code.
omap_8250_set_termios() would likely profit from a cleanup similar to
one in serial8250_do_set_termios() in commit cdc4a3e0b2 ("serial:
8250: extract serial8250_set_fcr()") and earlier.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250814072456.182853-12-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Having all the new guards, use them in the 8250 code. This improves
readability, makes error handling easier, and marks locked portions of
code explicit.
serial_unlink_irq_chain() is done separately here because with the
guard() used, those BUG_ON()s can be switched WARN_ON()s as we can
actually handle the conditions and return (despite something went really
wrong).
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250814072456.182853-11-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Having all the new guards, use them in the 8250 code. This improves
readability, makes error handling easier, and marks locked portions of
code explicit.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250814072456.182853-10-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Having all the new guards, use them in the serial_core code. This
improves readability, makes error handling easier, and marks locked
portions of code explicit.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250814072456.182853-9-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Having this, guards like these work:
guard(serial8250_rpm)(up);
or
scoped_guard(serial8250_rpm, up) {
...
}
See e.g. "serial: 8250: use guard()s" later in this series.
And make them available to anyone (EXPORT + put in 8250.h) as drivers
open code this anyway.
The _tx ones are not defined as they would have no user.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250814072456.182853-5-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When trying to set MCR[2], XON1 is incorrectly accessed instead. And when
writing to the TCR register to configure flow control levels, we are
incorrectly writing to the MSR register. The default value of $00 is then
used for TCR, which means that selectable trigger levels in FCR are used
in place of TCR.
TCR/TLR access requires EFR[4] (enable enhanced functions) and MCR[2]
to be set. EFR[4] is already set in probe().
MCR access requires LCR[7] to be zero.
Since LCR is set to $BF when trying to set MCR[2], XON1 is incorrectly
accessed instead because MCR shares the same address space as XON1.
Since MCR[2] is unmodified and still zero, when writing to TCR we are in
fact writing to MSR because TCR/TLR registers share the same address space
as MSR/SPR.
Fix by first removing useless reconfiguration of EFR[4] (enable enhanced
functions), as it is already enabled in sc16is7xx_probe() since commit
43c51bb573 ("sc16is7xx: make sure device is in suspend once probed").
Now LCR is $00, which means that MCR access is enabled.
Also remove regcache_cache_bypass() calls since we no longer access the
enhanced registers set, and TCR is already declared as volatile (in fact
by declaring MSR as volatile, which shares the same address).
Finally disable access to TCR/TLR registers after modifying them by
clearing MCR[2].
Note: the comment about "... and internal clock div" is wrong and can be
ignored/removed as access to internal clock div registers (DLL/DLH)
is permitted only when LCR[7] is logic 1, not when enhanced features
is enabled. And DLL/DLH access is not needed in sc16is7xx_startup().
Fixes: dfeae619d7 ("serial: sc16is7xx")
Cc: stable@vger.kernel.org
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20250731124451.1108864-1-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace the hardcoded GENI_UART_PORTS macro with a new Kconfig option
SERIAL_QCOM_GENI_UART_PORTS to allow platforms to configure the maximum
number of UART ports supported by the driver at build time.
This improves flexibility for platforms that require more than the
previously fixed number of UART ports, and avoids unnecessary allocation
for unused ports.
Signed-off-by: Zong Jiang <quic_zongjian@quicinc.com>
Link: https://lore.kernel.org/r/20250812054819.3748649-3-quic_zongjian@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace the static allocation of UART ports with dynamic allocation
using devm_kzalloc. This change removes the fixed-size array and instead
allocates each UART port structure on demand during probe, improving
memory efficiency and scalability.
Signed-off-by: Zong Jiang <quic_zongjian@quicinc.com>
Link: https://lore.kernel.org/r/20250812054819.3748649-2-quic_zongjian@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The round_rate() clk ops is deprecated, so migrate this driver from
round_rate() to determine_rate() using the Coccinelle semantic patch
appended to the "under-the-cut" portion of the patch.
Signed-off-by: Brian Masney <bmasney@redhat.com>
Link: https://lore.kernel.org/r/20250810-tty-round-rate-v1-1-849009f3bdfd@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function serial8250_probe_platform() in 8250_platform.c triggered a
frame size warning:
drivers/tty/serial/8250/8250_platform.c: In function ‘serial8250_probe_platform.isra’:
drivers/tty/serial/8250/8250_platform.c:201:1: warning: the frame size of 1184 bytes is larger than 1024 bytes [-Wframe-larger-than=]
This patch reduces the stack usage by dynamically allocating the
`uart` structure using kzalloc(), rather than placing it on
the stack. This eliminates the overflow warning and improves kernel
robustness.
Signed-off-by: Abinash Singh <abinashsinghlalotra@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250806215134.4921-3-abinashsinghlalotra@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function serial8250_probe_acpi() in 8250_platform.c triggered a
frame size warning:
drivers/tty/serial/8250/8250_platform.c: In function ‘serial8250_probe_acpi’:
drivers/tty/serial/8250/8250_platform.c:152:1: warning: the frame size of 1160 bytes is larger than 1024 bytes [-Wframe-larger-than=]
This patch reduces the stack usage by dynamically allocating the
`uart` structure using kzalloc(), rather than placing it on
the stack. This eliminates the overflow warning and improves kernel
robustness.
Signed-off-by: Abinash Singh <abinashsinghlalotra@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250806215134.4921-2-abinashsinghlalotra@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit 84a9582fd2 ("serial: core: Start managing serial controllers
to enable runtime PM") serial drivers need to provide a device in
struct uart_port.dev otherwise an oops happens. To fix this issue
for ip22zilog driver switch driver to a platform driver and setup
the serial device in sgi-ip22 code.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Link: https://lore.kernel.org/r/20250725134018.136113-1-tsbogend@alpha.franken.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Christoph suggested that the explicit _GPL_ can be dropped from the
module namespace export macro, as it's intended for in-tree modules
only. It would be possible to restrict it technically, but it was
pointed out [2] that some cases of using an out-of-tree build of an
in-tree module with the same name are legitimate. But in that case those
also have to be GPL anyway so it's unnecessary to spell it out in the
macro name.
Link: https://lore.kernel.org/all/aFleJN_fE-RbSoFD@infradead.org/ [1]
Link: https://lore.kernel.org/all/CAK7LNATRkZHwJGpojCnvdiaoDnP%2BaeUXgdey5sb_8muzdWTMkA@mail.gmail.com/ [2]
Suggested-by: Christoph Hellwig <hch@infradead.org>
Reviewed-by: Shivank Garg <shivankg@amd.com>
Acked-by: David Hildenbrand <david@redhat.com>
Acked-by: Nicolas Schier <n.schier@avm.de>
Reviewed-by: Daniel Gomez <da.gomez@samsung.com>
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Link: https://lore.kernel.org/20250808-export_modules-v4-1-426945bcc5e1@suse.cz
Signed-off-by: Christian Brauner <brauner@kernel.org>
The conversion of all GPIO drivers to using the .set_rv() and
.set_multiple_rv() callbacks from struct gpio_chip (which - unlike their
predecessors - return an integer and allow the controller drivers to
indicate failures to users) is now complete and the legacy ones have
been removed. Rename the new callbacks back to their original names in
one sweeping change.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
I am switching my address to a personal domain, so some files in the
SGI IP30 and IOC3 files need to be updated. I will send updates for
the MAINTAINERS file and rtc-ds1685 separately to linux-rtc.
Signed-off-by: Joshua Kinard <kumba@gentoo.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
When the PSLVERR_RESP_EN parameter is set to 1, the device generates
an error response if an attempt is made to read an empty RBR (Receive
Buffer Register) while the FIFO is enabled.
In serial8250_do_startup(), calling serial_port_out(port, UART_LCR,
UART_LCR_WLEN8) triggers dw8250_check_lcr(), which invokes
dw8250_force_idle() and serial8250_clear_and_reinit_fifos(). The latter
function enables the FIFO via serial_out(p, UART_FCR, p->fcr).
Execution proceeds to the serial_port_in(port, UART_RX).
This satisfies the PSLVERR trigger condition.
When another CPU (e.g., using printk()) is accessing the UART (UART
is busy), the current CPU fails the check (value & ~UART_LCR_SPAR) ==
(lcr & ~UART_LCR_SPAR) in dw8250_check_lcr(), causing it to enter
dw8250_force_idle().
Put serial_port_out(port, UART_LCR, UART_LCR_WLEN8) under the port->lock
to fix this issue.
Panic backtrace:
[ 0.442336] Oops - unknown exception [#1]
[ 0.442343] epc : dw8250_serial_in32+0x1e/0x4a
[ 0.442351] ra : serial8250_do_startup+0x2c8/0x88e
...
[ 0.442416] console_on_rootfs+0x26/0x70
Fixes: c49436b657 ("serial: 8250_dw: Improve unwritable LCR workaround")
Link: https://lore.kernel.org/all/84cydt5peu.fsf@jogness.linutronix.de/T/
Signed-off-by: Yunhui Cui <cuiyunhui@bytedance.com>
Reviewed-by: John Ogness <john.ogness@linutronix.de>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20250723023322.464-2-cuiyunhui@bytedance.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Qualcomm automotive SA8255p SoC relies on firmware to configure
platform resources, including clocks, interconnects and TLMM.
The driver requests resources operations over SCMI using power
and performance protocols.
The SCMI power protocol enables or disables resources like clocks,
interconnect paths, and TLMM (GPIOs) using runtime PM framework APIs,
such as resume/suspend, to control power states(on/off).
The SCMI performance protocol manages UART baud rates, with each baud
rate represented by a performance level. The driver uses the
dev_pm_opp_set_level() API to request the desired baud rate by
specifying the performance level.
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Praveen Talari <quic_ptalari@quicinc.com>
Link: https://lore.kernel.org/r/20250721174532.14022-9-quic_ptalari@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The GENI serial driver currently handles power resource management
through calls to the statically defined geni_serial_resources_on() and
geni_serial_resources_off() functions. This approach reduces modularity
and limits support for platforms with diverse power management
mechanisms, including resource managed by firmware.
Improve modularity and enable better integration with platform-specific
power management, introduce support for runtime PM. Use
pm_runtime_resume_and_get() and pm_runtime_put_sync() within the
qcom_geni_serial_pm() callback to control resource power state
transitions based on UART power state changes.
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Praveen Talari <quic_ptalari@quicinc.com>
Link: https://lore.kernel.org/r/20250721174532.14022-8-quic_ptalari@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Facilitates future modifications within the new function,
leading to better readability and maintainability of the code.
Move the code that handles the actual logic of clock-rate
calculations to a separate function geni_serial_set_rate()
which enhances code readability.
Signed-off-by: Praveen Talari <quic_ptalari@quicinc.com>
Link: https://lore.kernel.org/r/20250721174532.14022-7-quic_ptalari@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Supports use in PM system/runtime frameworks, helping to distinguish new
resource control mechanisms and facilitate future modifications within
the new API.
The code that handles the actual enable or disable of resources like clock
and ICC paths to a separate function (geni_serial_resources_on() and
geni_serial_resources_off()) which enhances code readability.
Introduced minor return checks in newly added function APIs to enhance
error detection and prevent silent failures.
Signed-off-by: Praveen Talari <quic_ptalari@quicinc.com>
Link: https://lore.kernel.org/r/20250721174532.14022-6-quic_ptalari@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enhances code readability and future modifications within the new API.
Move the code that handles the actual initialization of resources
like clock and ICC paths to a separate function, making the
probe function cleaner.
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Praveen Talari <quic_ptalari@quicinc.com>
Link: https://lore.kernel.org/r/20250721174532.14022-5-quic_ptalari@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a spelling mistake of 'notifer' in the comment which
should be 'notifier'.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: WangYuli <wangyuli@uniontech.com>
Link: https://lore.kernel.org/r/BD4804BF4FBA1648+20250722073431.21983-6-wangyuli@uniontech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On i386, when
CONFIG_X86_INTEL_CE=y
# CONFIG_SERIAL_8250 is not set
it will try to compile the driver and use the stub simultaneously.
This breaks the build. Fix it by making sure that the driver
compiles only when CONFIG_SERIAL_8250 is also enabled.
On top of that ensure that CONFIG_SERIAL_8250 is actually set to 'y'
and not 'm' as the later makes no sense for this platform. The hook
may only be applied during early boot.
Fixes: acc902de05 ("serial: 8250: Move CE4100 quirks to a module under 8250 driver")
Fixes: 5ec6960f6f ("ce4100: Add errata fixes for UART on CE4100")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Closes: https://lore.kernel.org/r/cdf4ee46-7bf8-4379-9245-fed9db72e7e8@infradead.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20250716142412.1667927-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCgA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmh9azkeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG7GIH/0lpQtHRl6N+q2Qs
v75iG2ZouWyw2JlhUOHAToKU58MZqqTXLZzc8ZdY6fAd7DpXWKRGSDsyWVyLbUkt
UKGzXEIJsHXYvw2QIPbhkY9gQBWpdZTh4tHztFyKb0QLn81qkibVP6ChOwSzOGa/
xUyQ5v6yH+JvQlnQaCgy6hi7cMrLNSNZmuIjy0yc5Y153YPEtX5OUPO2PstpUx5r
AuiOhU4ewW9QCe07X/Pk7tdn0T2Jg8Kwk1FViaM0RBUf/0GXGfsovIxpUP/eCyMc
MA+9SXXLlDa/4Z8w3EsQYx6m2MnNmm0HPeevCmWqq3+Ocooik4si1BpzHfUaE6n/
/0D8zBg=
=NzEi
-----END PGP SIGNATURE-----
Merge tag 'v6.16-rc7' into tty-next
We need the tty/serial fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert the Renesas SuperH SCI(F) serial port driver from
SIMPLE_DEV_PM_OPS() to DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr().
This lets us drop the __maybe_unused annotations from its suspend and
resume callbacks, and reduces kernel size in case CONFIG_PM or
CONFIG_PM_SLEEP is disabled.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/a5628fe028362ae3f8729021a7864dd39f7869bf.1752086885.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Define a new RSCI port type, and the RSCI 32 bits registers set.
The RZ/T2H SCI has a a fifo, and a quite different set of registers
from the original SH SCI ones.
DMA is not supported yet.
Signed-off-by: Thierry Bultel <thierry.bultel.yh@bp.renesas.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20250630202323.279809-6-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
New port types cannot be added in serial_core.h, which is shared with
userspace.
In order to support new port types, the coming new ones will have
BIT(7) set in the id value, and in this case, uartport->type is
set to PORT_GENERIC.
This commit therefore changes all the places where the port type is
read, by not relying on uartport->type but on the private
value stored in struct sci_port.
Signed-off-by: Thierry Bultel <thierry.bultel.yh@bp.renesas.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20250630202323.279809-5-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace direct calls to sci_stop_rx() and sci_stop_tx() with port ops
callbacks in sci_shutdown(). This enables the RSCI driver, which reuses
the SCI core but implements its own stop_rx and stop_tx logic, to reuse
sci_shutdown() without duplicating code.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20250630202323.279809-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In one place in ce4100_mem_serial_in() the code may be replaced with
mem_serial_in() call. Do it so and collapse two conditionals into one.
Suggested-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250701134200.2621898-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dma_sync_sg_for_device() functions should be called with the same
nents as the dma_map_sg(), not the value the map function returned
according to the documentation in Documentation/core-api/dma-api.rst:450:
With the sync_sg API, all the parameters must be the same
as those passed into the sg mapping API.
Fixes: da3564ee02 ("pch_uart: add multi-scatter processing")
Cc: stable <stable@kernel.org>
Signed-off-by: Thomas Fourier <fourier.thomas@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250701113452.18590-2-fourier.thomas@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to drop the OF node reference taken when initialising the
control and port devices when the devices are later released.
Fixes: d36f0e9a00 ("serial: core: restore of_node information in sysfs")
Cc: Aidan Stewart <astewart@tektelic.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20250708085817.16070-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is inconvenient for maintainers and maintainership to have
some quirks under architectural code. Move it to the specific quirk
file like other 8250-compatible drivers do.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250627182743.1273326-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'struct lpuart_soc_data' are not modified in this driver.
Constifying these structures moves some data to a read-only section, so
increases overall security.
This also makes the code more consistent.
On a x86_64, with allmodconfig, as an example:
Before:
======
text data bss dec hex filename
172668 23470 128 196266 2feaa drivers/tty/serial/fsl_lpuart.o
After:
=====
text data bss dec hex filename
172924 23214 128 196266 2feaa drivers/tty/serial/fsl_lpuart.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/93dc860a06f92236db283c71be0640cc477b7291.1751092467.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 7a637784d5 ("serial: imx: reduce RX interrupt frequency")
introduced a regression on the i.MX6UL EVK board. The issue can be
reproduced with the following steps:
- Open vi on the board.
- Paste a text file (~150 characters).
- Save the file, then repeat the process.
- Compare the sha256sum of the saved files.
The checksums do not match due to missing characters or entire lines.
Fix this by restoring the RXTL value to 1 when the UART is used as a
console.
This ensures timely RX interrupts and reliable data reception in console
mode.
With this change, pasted content is saved correctly, and checksums are
always consistent.
Cc: stable <stable@kernel.org>
Fixes: 7a637784d5 ("serial: imx: reduce RX interrupt frequency")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/20250619114617.2791939-1-festevam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The check for "port.type == PORT_8250_CIR" is present twice in
serial8250_register_8250_port(). The latter was already tried to be
dropped by 1104321a7b ("serial: Delete dead code for CIR serial
ports") and then reverted by 9527b82ae3 ("Revert "serial: Delete dead
code for CIR serial ports"").
Document this weirdness with a reason.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: "Maciej S. Szmigiero" <mail@maciej.szmigiero.name>
Link: https://lore.kernel.org/all/aFcDOx1bdB34I5hS@surfacebook.localdomain/
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20250624080641.509959-5-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are already variables like 'iir_noint1' and 'iir_noint2'. Follow
the preexisting lowercase naming of variables. So s/lsr_TEMT/lsr_temt/
and 'iir_NOINT' likewise.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Suggested-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250624080641.509959-4-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit 795158691c ("serial: 8250: extract
serial8250_initialize()"), split serial8250_initialize() even more --
the TX enable test part of this code can be separated into
serial8250_iir_txen_test().
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Suggested-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250624080641.509959-3-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit 795158691c ("serial: 8250: extract
serial8250_initialize()"), split serial8250_initialize() even more --
the mctrl part of this code can be separated into
serial8250_init_mctrl() -- done now.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Suggested-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250624080641.509959-2-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The RSA functions moved by the below commit to 8250_rsa.c are used in
8250_base.c. Since that can be a module (when CONFIG_SERIAL_8250=m),
this causes build failures:
ERROR: modpost: "rsa_autoconfig" [drivers/tty/serial/8250/8250_base.ko] undefined!
ERROR: modpost: "rsa_reset" [drivers/tty/serial/8250/8250_base.ko] undefined!
ERROR: modpost: "rsa_disable" [drivers/tty/serial/8250/8250_base.ko] undefined!
ERROR: modpost: "rsa_enable" [drivers/tty/serial/8250/8250_base.ko] undefined!
Fix them by exporting the functions. But only to the base module using
EXPORT_SYMBOL_GPL_FOR_MODULES(). (And not to the whole world.)
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://lore.kernel.org/all/20250619165607.33403e19@canb.auug.org.au/
Fixes: 5a128fb475 ("serial: 8250: move RSA functions to 8250_rsa.c")
Link: https://lore.kernel.org/r/20250623061035.436414-1-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since in v6.8-rc1, the of_node symlink under tty devices is
missing. This breaks any udev rules relying on this information.
Link the of_node information in the serial controller device with the
parent defined in the device tree. This will also apply to the serial
device which takes the serial controller as a parent device.
Fixes: b286f4e87e ("serial: core: Move tty and serdev to be children of serial core port device")
Cc: stable@vger.kernel.org
Signed-off-by: Aidan Stewart <astewart@tektelic.com>
Link: https://lore.kernel.org/r/20250617164819.13912-1-astewart@tektelic.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The serial info sometimes produces negative TX/RX counts. E.g.:
3: uart:FSL_LPUART mmio:0x02970000 irq:46 tx:-1595870545 rx:339619
RTS|CTS|DTR|DSR|CD
It appears that the print format specifiers don't match with the types of
the respective variables. E.g.: All of the fields in struct uart_icount
are u32, but the format specifier used is %d, even though u32 is unsigned
and %d is for signed integers. Update drivers/tty/serial/serial_core.c
to use the proper format specifiers. Reference
https://docs.kernel.org/core-api/printk-formats.html as the documentation
for what format specifiers are the proper ones to use for a given C type.
Signed-off-by: Joseph Tilahun <jtilahun@astranis.com>
Link: https://lore.kernel.org/r/20250610065653.3750067-1-jtilahun@astranis.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable the use of the RTS pin for direction control in half-duplex modes to
prevent data collisions. Utilize the rs485 structure and callbacks in the
serial core framework to support half-duplex modes. Implement support for
the TIOCSRS485 IOCTL value and the struct serial_rs485.
Signed-off-by: Anup Kulkarni <quic_anupkulk@quicinc.com>
Link: https://lore.kernel.org/r/20250603110145.3835111-1-quic_anupkulk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current GENI UART driver supports Max Baud rate up to 4 Mbps.
Add support to increase maximum baud rate to 8 Mbps.
Signed-off-by: Jyothi Kumar Seerapu <quic_jseerapu@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250523103721.5042-1-quic_jseerapu@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are unnecessary "up->port." accesses on many places in 8250_omap.
"port" is avalable on most places, so instead simply use "port->".
And make port available in omap8250_restore_regs() too. It's used on
many places in there.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250611100319.186924-34-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of open-coding the hash table, use the one provided by
hashtable.h. The semantics is the same, except the code needs not to
compute the hash bucket on its own.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250611100319.186924-33-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no point in a long 'if' in serial8250_register_8250_port() to
just return ENOSPC for PORT_8250_CIR ports. Invert the condition and
return immediately.
'gpios' variable was moved to its set location.
And return ENODEV instead of ENOSPC. The latter is a leftover from the
previous find-uart 'if'. The former makes a lot more sense in this case.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20250611100319.186924-31-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DEBUG_AUTOCONF() is always disabled (by "#if 0"), so one would need to
recompile the kernel to use it. And even if they did, they would find
out it is broken anyway:
error: variable 'scratch' is used uninitialized whenever 'if' condition is false
Drop it.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20250611100319.186924-30-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These are useless, we have tracing nowadays.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20250611100319.186924-29-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This find-or-create-irq part of the serial_link_irq_chain()'s code is
logically bounded and self-standing. For easier-to-follow code flow,
extract the code to a separate function:
serial_get_or_create_irq_info().
This allows for an easier found-an-irq handling -- simple jump to the
'unlock' label and return. That results in one less 'if' levels.
Note when using guard()s in the upcoming patchset, the label can dropped
altogether.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20250611100319.186924-28-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'frac' is not used in the generic implementation of get_divisor. Drop it
from there. (Only some port->get_divisor() compute that and receive it
then to port->set_divisor()).
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20250611100319.186924-27-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* use 'lcr' as variable containing the "computed value" (and not 'cval')
* use 'u8' for the type (and not 'unsigned char')
* drop useless comment
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20250611100319.186924-26-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial8250_do_set_termios() consists of many registers and up flags
settings. Extract all these into separate functions. This time, setting
of FCR.
serial8250_do_set_termios() looks sane at this point.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20250611100319.186924-25-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial8250_do_set_termios() consists of many registers and up flags
settings. Extract all these into separate functions. This time, setting
of EFR for UART_CAP_EFR ports.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250611100319.186924-24-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial8250_do_set_termios() consists of many registers and up flags
settings. Extract all these into separate functions. This time, setting
of IER.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20250611100319.186924-23-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial8250_do_set_termios() consists of many registers and up flags
settings. Extract all these into separate functions. This time, setting
of ignore_status_mask and read_status_mask.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250611100319.186924-22-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial8250_do_set_termios() consists of many registers and up flags
settings. Extract all these into separate functions. This time, setting
of MCR for UART_CAP_AFE ports.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20250611100319.186924-21-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial8250_do_set_termios() consists of many registers and up flags
settings. Extract all these into separate functions. This time, setting
of trigger level for slow speeds.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20250611100319.186924-20-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial8250_do_set_termios() consists of many registers and up flags
settings. Extract all these into separate functions. This time, setting
of CSIZE for UART_CAP_MINI ports.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20250611100319.186924-19-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On three places in 8250_port.c, the interrupts are cleared by reading 4
registers. Extract this to a separate function:
serial8250_clear_interrupts(). And call it from all the places.
Note autoconfig_irq() now uses serial_port_in() instead of serial_in().
But they are the same, in fact (modulo parameter).
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20250611100319.186924-18-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial8250_do_startup() initializes the ports in the middle of the
function. This code can be separated to serial8250_initialize(), so that
serial8250_do_startup() can be readable again.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250611100319.186924-17-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial8250_do_startup() contains a stand-alone code for probing THRE.
Furthermore, the code block is conditional (port->irq and test for
UPF_NO_THRE_TEST).
Move this code to a separate function. The conditional can be evaluated
easier there -- by a simple return in the beginning. So the indentation
level lowers and the code is overall more readable now.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250611100319.186924-16-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial8250_do_startup() contains peculiar trigger levels setup for
special ports (16850, ALTR_16550_*). Move this away to a separate
function: serial8250_set_TRG_levels().
And use switch-case instead of 'if's.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20250611100319.186924-15-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Let the serial8250_do_startup() code handle the special ports (16C950,
DA830, RSA) startup in a separate function:
serial8250_startup_special().
And instead of multiple if-else-if, use switch-case. So that it can be
easily checked for PORT_RSA now too.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20250611100319.186924-14-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
They are RSA-specific, so should live in a preexisting 8250_rsa.c. Move
them there.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20250611100319.186924-13-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prefix the functions with rsa_, not suffix.
This is a preparation for moving them out to 8250_rsa.c in the next
patch.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20250611100319.186924-12-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code can short-return in case something does not hold. So invert the
conditions and return in those cases immediately. This makes the code
flow more natural and less nested.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20250611100319.186924-11-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All these:
#ifdef CONFIG_SERIAL_8250_RSA
...
#endif
in the 8250 generic code distract the reader. Introduce empty inlines to
handle the !CONFIG_SERIAL_8250_RSA case and handle the '#if's around the
RSA functions definitions.
This means rsa_autoconfig() and rsa_reset() functions were introduced to
contain the particular code.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20250611100319.186924-10-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_port::{serial_in,serial_out} (and plat_serial8250_port::* likewise)
historically use:
* 'unsigned int' for 32-bit register values in reads and writes, and
* 'int' for offsets.
Make them sane such that:
* 'u32' is used for register values, and
* 'unsigned int' is used for offsets.
While at it, name hooks' parameters, so it is clear what is what.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: Madhavan Srinivasan <maddy@linux.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250611100319.186924-9-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This code (tty_get -> vhangup -> tty_put) is repeated on few places.
Introduce a helper similar to tty_port_tty_hangup() (asynchronous) to
handle even vhangup (synchronous).
And use it on those places.
In fact, reuse the tty_port_tty_hangup()'s code and call tty_vhangup()
depending on a new bool parameter.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: David Lin <dtwlin@gmail.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Alex Elder <elder@kernel.org>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20250611100319.186924-2-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move this API to the canonical timer_*() namespace.
[ tglx: Redone against pre rc1 ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/aB2X0jCKQO56WdMt@gmail.com
Commit 1788cf6a91 ("tty: serial: switch from circ_buf to kfifo")
introduced an error in the TX DMA handling for 8250_omap.
When the OMAP_DMA_TX_KICK flag is set, the "skip_byte" is pulled from
the kfifo and emitted directly in order to start the DMA. While the
kfifo is updated, dma->tx_size is not decreased. This leads to
uart_xmit_advance() called in omap_8250_dma_tx_complete() advancing the
kfifo by one too much.
In practice, transmitting N bytes has been seen to result in the last
N-1 bytes being sent repeatedly.
This change fixes the problem by moving all of the dma setup after the
OMAP_DMA_TX_KICK handling and using kfifo_len() instead of the DMA size
for the 4-byte cutoff check. This slightly changes the behaviour at
buffer wraparound, but it still transmits the correct bytes somehow.
Now, the "skip_byte" would no longer be accounted to the stats. As
previously, dma->tx_size included also this skip byte, up->icount.tx was
updated by aforementioned uart_xmit_advance() in
omap_8250_dma_tx_complete(). Fix this by using the uart_fifo_out()
helper instead of bare kfifo_get().
Based on patch by Mans Rullgard <mans@mansr.com>
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Fixes: 1788cf6a91 ("tty: serial: switch from circ_buf to kfifo")
Link: https://lore.kernel.org/all/20250506150748.3162-1-mans@mansr.com/
Reported-by: Mans Rullgard <mans@mansr.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20250522053835.3495975-1-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor parity calculations to use the standard parity8() helper.
This change eliminates redundant implementations.
Co-developed-by: Yu-Chun Lin <eleanor15x@gmail.com>
Signed-off-by: Yu-Chun Lin <eleanor15x@gmail.com>
Signed-off-by: Kuan-Wei Chiu <visitorckw@gmail.com>
Link: https://lore.kernel.org/r/20250515081311.775559-1-visitorckw@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Systems that issue PCIe hot reset requests during a suspend/resume
cycle cause PCI1XXXX device revisions prior to C0 to get its UART
configuration registers reset to hardware default values. This results
in device inaccessibility and data transfer failures. Starting with
Revision C0, support was added in the device hardware (via the Hot
Reset Disable Bit) to allow resetting only the PCIe interface and its
associated logic, but preserving the UART configuration during a hot
reset. This patch enables the hot reset disable feature during suspend/
resume for C0 and later revisions of the device.
Signed-off-by: Rengarajan S <rengarajan.s@microchip.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250425145500.29036-1-rengarajan.s@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ExynosAutov920 SoC supports 18 UART ports, update
the value of UART_NR to accommodate the same.
Signed-off-by: Faraz Ata <faraz.ata@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250429102941.4138463-1-faraz.ata@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCgA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmgOrWseHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGFyIH/AhXcuA8y8rk43mo
t+0GO7JR4dnr4DIl74GgDjCXlXiKCT7EXMfD/ABdofTxV4Pbyv+pUODlg1E6eO9U
C1WWM5PPNBGDDEVSQ3Yu756nr0UoiFhvW0R6pVdou5cezCWAtIF9LTN8DEUgis0u
EUJD9+/cHAMzfkZwabjm/HNsa1SXv2X47MzYv/PdHKr0htEPcNHF4gqBrBRdACGy
FJtaCKhuPf6TcDNXOFi5IEWMXrugReRQmOvrXqVYGa7rfUFkZgsAzRY6n/rUN5Z9
FAgle4Vlv9ohVYj9bXX8b6wWgqiKRpoN+t0PpRd6G6ict1AFBobNGo8LH3tYIKqZ
b/dCGNg=
=xDGd
-----END PGP SIGNATURE-----
Merge 6.15-rc4 into tty-next
We need the tty/serial fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 8700a7ea55 (serial: 8250_omap: Drop
pm_runtime_irq_safe()), all the serial8250_rpm_*() functions are used
solely in 8250_port.
Unexport them.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250425111315.1036184-7-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_get_icount() and uart_carrier_raised() open code
uart_port_ref_lock(). Use the helper instead.
The difference is we use _irqsave() variants of a spinlock now. But
that's "safer" than _irq().
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250425111315.1036184-6-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_port_lock() and uart_port_unlock() are (at the same time) defined
as:
* functions in include/linux/serial_core.h
* macros in drivers/tty/serial/serial_core.c
The former are sane uart port lock wrappers.
The latter _lock() does something completely different: it inspects
a uart_state, obtains a uart_port from it, and increases its reference
count. And if that all succeeded, the port is locked too.
Similarly, the _unlock() counterpart first unlocks and then decrements
the refcount too.
This state is REALLY CONFUSING.
So rename the latter (local .c macros):
* uart_port_lock() -> uart_port_ref_lock(), and
* uart_port_unlock() -> uart_port_unlock_deref().
Now, the forbidden while-at-it part: convert from a macro to an inline
-- do it here as the passed 'flags' have to be pointer to ulong now. So
we avoid doubled changes on identical LOCs.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250425111315.1036184-5-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The inline-defined constants look weird. Instead, define a proper enum
for them and type uart_port::iotype as that enum. This allows for proper
checking in switch-case labels (somewhere, a default or UPIO_UNKNOWN
label needs to be added/handled).
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250425111315.1036184-4-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
startup()/shutdown() callbacks access SIFIVE_SERIAL_IE_OFFS.
The register is also accessed from write() callback.
If console were printing and startup()/shutdown() callback
gets called, its access to the register could be overwritten.
Add port->lock to startup()/shutdown() callbacks to make sure
their access to SIFIVE_SERIAL_IE_OFFS is synchronized against
write() callback.
Fixes: 45c054d081 ("tty: serial: add driver for the SiFive UART")
Signed-off-by: Ryo Takakura <ryotkkr98@gmail.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Cc: stable@vger.kernel.org
Reviewed-by: John Ogness <john.ogness@linutronix.de>
Rule: add
Link: https://lore.kernel.org/stable/20250330003522.386632-1-ryotkkr98%40gmail.com
Link: https://lore.kernel.org/r/20250412001847.183221-1-ryotkkr98@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Save the bus clock pointer in the of_serial_info structure, and use
that to disable the bus clock on suspend and re-enable it on resume.
Signed-off-by: Alex Elder <elder@riscstar.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Reviewed-by: Yixun Lan <dlan@gentoo.org>
Link: https://lore.kernel.org/r/20250411203828.1491595-4-elder@riscstar.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the necessary callbacks(write_atomic, write_thread, device_lock
and device_unlock) and CON_NBCON flag to switch the sifive console
driver to perform as nbcon console.
Both ->write_atomic() and ->write_thread() will check for console
ownership whenever they are accessing registers.
The ->device_lock()/unlock() will provide the additional serilization
necessary for ->write_thread() which is called from dedicated printing
thread.
Signed-off-by: Ryo Takakura <ryotkkr98@gmail.com>
Reviewed-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20250412002544.185038-1-ryotkkr98@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MSM UART DM controller supports different working modes, e.g. DMA or
the "single-character mode", where all reads/writes operate on a single
character rather than 4 chars (32-bit) at once. When using earlycon,
__msm_console_write() always writes 4 characters at a time, but we don't
know which mode the bootloader was using and we don't set the mode either.
This causes garbled output if the bootloader was using the single-character
mode, because only every 4th character appears in the serial console, e.g.
"[ 00oni pi 000xf0[ 00i s 5rm9(l)l s 1 1 SPMTA 7:C 5[ 00A ade k d[
00ano:ameoi .Q1B[ 00ac _idaM00080oo'"
If the bootloader was using the DMA ("DM") mode, output would likely fail
entirely. Later, when the full serial driver probes, the port is
re-initialized and output works as expected.
Fix this also for earlycon by clearing the DMEN register and
reset+re-enable the transmitter to apply the change. This ensures the
transmitter is in the expected state before writing any output.
Cc: stable <stable@kernel.org>
Fixes: 0efe729634 ("tty: serial: msm: Add earlycon support")
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250408-msm-serial-earlycon-v1-1-429080127530@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The aim here is to provide an easier support to more different SCI
controllers, like the RZ/T2H one.
The existing .data field of_sci_match is changed to a structure containing
all what that can be statically initialized, and avoid a call to
'sci_probe_regmap', in both 'sci_init_single', and 'early_console_setup'.
'sci_probe_regmap' is now assumed to be called in the only case where the
device description is from a board file instead of a dts.
In this way, there is no need to patch 'sci_probe_regmap' for adding new
SCI type, and also, the specific sci_port_params for a new SCI type can be
provided by an external file.
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Thierry Bultel <thierry.bultel.yh@bp.renesas.com>
Link: https://lore.kernel.org/r/20250403212919.1137670-10-thierry.bultel.yh@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The aim here is to prepare support for new sci controllers like
the T2H/RSCI whose registers are too much different for being
handled in common code.
This named serial controller also has 32 bits register,
so some return types had to be changed.
The needed generic functions are no longer static, with prototypes
defined in sh-sci-common.h so that they can be used from specific
implementation in a separate file, to keep this driver as little
changed as possible.
For doing so, a set of 'ops' is added to struct sci_port.
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Thierry Bultel <thierry.bultel.yh@bp.renesas.com>
Link: https://lore.kernel.org/r/20250403212919.1137670-9-thierry.bultel.yh@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The comment was correct when it was added, at that time RZ/T1 was
the only SoC in the RZ/T line. Since then, further SoCs have been
added with RZ/T names which do not use the same SCIFA register
layout and so the comment is now misleading.
So we update the comment to explicitly reference only RZ/T1 SoCs.
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Thierry Bultel <thierry.bultel.yh@bp.renesas.com>
Link: https://lore.kernel.org/r/20250403212919.1137670-8-thierry.bultel.yh@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
devm_ioremap() can return NULL on error. Currently, mlb_usio_probe()
does not check for this case, which could result in a NULL pointer
dereference.
Add NULL check after devm_ioremap() to prevent this issue.
Fixes: ba44dc0430 ("serial: Add Milbeaut serial control")
Signed-off-by: Henry Martin <bsdhenrymartin@gmail.com>
Link: https://lore.kernel.org/r/20250403070339.64990-1-bsdhenrymartin@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SpacemiT UART requires a bus clock to be enabled, in addition to
it's "normal" core clock. Look up the optional bus clock by name,
and if that's found, look up the core clock using the name "core".
Supplying a bus clock is optional. If no bus clock is needed, the
the first/only clock is used for the core clock.
Signed-off-by: Alex Elder <elder@riscstar.com>
Link: https://lore.kernel.org/r/20250409192213.1130181-3-elder@riscstar.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
struct gpio_chip now has callbacks for setting line values that return
an integer, allowing to indicate failures. Convert the driver to using
them.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20250408-gpiochip-set-rv-tty-v1-2-fb49444827d4@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
struct gpio_chip now has callbacks for setting line values that return
an integer, allowing to indicate failures. Convert the driver to using
them.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20250408-gpiochip-set-rv-tty-v1-1-fb49444827d4@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove unnecessary semicolons reported by Coccinelle/coccicheck and the
semantic patch at scripts/coccinelle/misc/semicolon.cocci.
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Link: https://lore.kernel.org/r/20250407040712.2577607-1-nichen@iscas.ac.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The absence of an alias in the device tree results in an invalid line
number, causing the driver probe to fail for GENI serial.
To prevent probe failures, dynamically assign line numbers if an alias is
not present in the device tree for non-console ports.
Signed-off-by: Viken Dadhaniya <quic_vdadhani@quicinc.com>
Link: https://lore.kernel.org/r/20250327070711.2585887-1-quic_vdadhani@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When two instances of uart devices are probing, a concurrency race can
occur. If one thread calls uart_register_driver function, which first
allocates and assigns memory to 'uart_state' member of uart_driver
structure, the other instance can bypass uart driver registration and
call ulite_assign. This calls uart_add_one_port, which expects the uart
driver to be fully initialized. This leads to a kernel panic due to a
null pointer dereference:
[ 8.143581] BUG: kernel NULL pointer dereference, address: 00000000000002b8
[ 8.156982] #PF: supervisor write access in kernel mode
[ 8.156984] #PF: error_code(0x0002) - not-present page
[ 8.156986] PGD 0 P4D 0
...
[ 8.180668] RIP: 0010:mutex_lock+0x19/0x30
[ 8.188624] Call Trace:
[ 8.188629] ? __die_body.cold+0x1a/0x1f
[ 8.195260] ? page_fault_oops+0x15c/0x290
[ 8.209183] ? __irq_resolve_mapping+0x47/0x80
[ 8.209187] ? exc_page_fault+0x64/0x140
[ 8.209190] ? asm_exc_page_fault+0x22/0x30
[ 8.209196] ? mutex_lock+0x19/0x30
[ 8.223116] uart_add_one_port+0x60/0x440
[ 8.223122] ? proc_tty_register_driver+0x43/0x50
[ 8.223126] ? tty_register_driver+0x1ca/0x1e0
[ 8.246250] ulite_probe+0x357/0x4b0 [uartlite]
To prevent it, move uart driver registration in to init function. This
will ensure that uart_driver is always registered when probe function
is called.
Signed-off-by: Jakub Lewalski <jakub.lewalski@nokia.com>
Signed-off-by: Elodie Decerle <elodie.decerle@nokia.com>
Link: https://lore.kernel.org/r/20250331160732.2042-1-elodie.decerle@nokia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Function dev_err() is redundant because platform_get_irq()
already prints an error.
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Acked-by: Mukesh Kumar Savaliya <quic_msavaliy@quicinc.com>
Link: https://lore.kernel.org/r/20250401080337.2187400-1-nichen@iscas.ac.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tidy up ACPI ID table:
- drop ACPI_PTR() and hence replace acpi.h with mod_devicetable.h et al.
- drop comma in the terminator entry
With that done, extend compile test coverage.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Chaitanya Vadrevu <chaitanya.vadrevu@emerson.com>
Reviewed-by: Chaitanya Vadrevu <chaitanya.vadrevu@emerson.com>
Link: https://lore.kernel.org/r/20250321182119.454507-8-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to use dev_err_probe() to simplify the error path and
unify a message template.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Chaitanya Vadrevu <chaitanya.vadrevu@emerson.com>
Reviewed-by: Chaitanya Vadrevu <chaitanya.vadrevu@emerson.com>
Link: https://lore.kernel.org/r/20250321182119.454507-7-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are serial_port_in()/serial_port_out() helpers to be used
instead of direct p->serial_in()/p->serial_out().
Use them in various 8250 drivers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Chaitanya Vadrevu <chaitanya.vadrevu@emerson.com>
Reviewed-by: Chaitanya Vadrevu <chaitanya.vadrevu@emerson.com>
Link: https://lore.kernel.org/r/20250321182119.454507-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
