The "airoha,en7581-chip-scu" is not a good compatible string in the en7523
case. Let's search chip scu regmap with "airoha,chip-scu" phangle first
and fallback to SoC specific chip scu compatible string on failure.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Signed-off-by: Linus Walleij <linusw@kernel.org>
Add support for olt pin function for olt pin group.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Signed-off-by: Linus Walleij <linusw@kernel.org>
Add support for pon pin function for pon_alt pin group.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Signed-off-by: Linus Walleij <linusw@kernel.org>
Add support for uart pin function for npu_uart pin group.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Signed-off-by: Linus Walleij <linusw@kernel.org>
In the an7581 case the register at 0x1FA20214 is called
RG_GPIO_2ND_I2C_MODE. The same register in the an7583 case is called
RG_SW_TOD_1PPS_MODE.
Let's rename this register to avoid potential confuse.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Signed-off-by: Linus Walleij <linusw@kernel.org>
We have only an7583 specific code in the pinctrl-an7583 kernel module,
so an7583 prefix is not necessary anymore. Remove it.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Signed-off-by: Linus Walleij <linusw@kernel.org>
We have only an7581 specific code in the pinctrl-an7581 kernel module,
so 'en7581_' prefix is not necessary anymore. Remove it.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Signed-off-by: Linus Walleij <linusw@kernel.org>
Split combined an7581/an7583 source file on a
* shared pinctrl code (pinctrl-airoha.c)
* an7581 specific pinctrl driver (pinctrl-an7581.c)
* an7583 specific pinctrl driver (pinctrl-an7583.c)
Ininialization code was adapted a bit to work properly for shared
and SoC specific cases.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Signed-off-by: Linus Walleij <linusw@kernel.org>
Let's move the SoC independent definitions and declarations of structures
required for Airoha SoC-specific pinctrl drivers to a common header. Later
we'll have several SoC-specific drivers, so this step is necessary.
We will not move to the common header file other register addresses,
register bitfields definitions and macroses that use SoC specific
information. We will keep SoC specific definitions inside SoC specific
files.
No functional changes.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Signed-off-by: Linus Walleij <linusw@kernel.org>
just a small refactoring to collect all gpio register information
in the one statically allocated structure.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Signed-off-by: Linus Walleij <linusw@kernel.org>
irq_type[] array inside airoha_pinctrl_gpiochip structure is not
actually necessary. Use trigger type from 'struct irq_data' instead.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Linus Walleij <linusw@kernel.org>
Edge-triggered interrupts are handled incorrectly because of
* no irq_ack() handler was defined,
* no handle_level_irq() handler was used,
This patch probably fixes an issue
Fixes: 1c8ace2d07 ("pinctrl: airoha: Add support for EN7581 SoC")
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Linus Walleij <linusw@kernel.org>
When using IRQCHIP_IMMUTABLE, airoha_irq_unmask() must manually call
gpiochip_enable_irq() and airoha_irq_mask() must call
gpiochip_disable_irq(). Without these calls, gpiolib never sets the
GPIOD_FLAG_IRQ_IS_ENABLED bit. Because this bit is missing,
gpiod_direction_output() will not realize the pin is actively used
as an interrupt.
Fixes: 1c8ace2d07 ("pinctrl: airoha: Add support for EN7581 SoC")
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Linus Walleij <linusw@kernel.org>
Without hooking .irq_request_resources, gpiolib cannot set
GPIOD_FLAG_USED_AS_IRQ. This breaks pin direction locking and can allow
userspace or another driver to reconfigure an active IRQ pin as an output
Fixes: 1c8ace2d07 ("pinctrl: airoha: Add support for EN7581 SoC")
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Linus Walleij <linusw@kernel.org>
airoha_irq_unmask(), airoha_irq_mask(), airoha_irq_type() functions
impements brain damaged logic to retrieve gpiochip and pinctrl pointers.
Details:
gpiochip = irq_data_get_irq_chip_data(data);
will initialize gpiochip variable with data->chip_data value. This value
initialized inside gpiochip_irq_map() function
static int gpiochip_irq_map(struct irq_domain *d, unsigned int irq,
irq_hw_number_t hwirq)
{
struct gpio_chip *gc = d->host_data;
...
irq_set_chip_data(irq, gc);
...
}
Thus gpiochip variable of 'struct airoha_pinctrl_gpiochip *' type will be
initialized with a pointer to a variable of 'struct gpio_chip' type.
Luckily, gpio_chip is the first element of airoha_pinctrl_gpiochip, so
gpiochip pointer will get a correct value.
This patch implements correct logic of getting gpiochip and pinctrl
pointers.
Fixes: 1c8ace2d07 ("pinctrl: airoha: Add support for EN7581 SoC")
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Signed-off-by: Linus Walleij <linusw@kernel.org>
The patch creates set_direction() helper for gpio_chip abstraction.
It also implements/reimplements some function using newly defined
helper.
This is cosmetic patch used to place gpio_chip specific code together.
No functional changes.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Signed-off-by: Linus Walleij <linusw@kernel.org>
This patch adds missed get_direction() function for gpio_chip.
Also it reimplements pinconf's get_direction() function using
newly defined function.
Fixes: 1c8ace2d07 ("pinctrl: airoha: Add support for EN7581 SoC")
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Signed-off-by: Linus Walleij <linusw@kernel.org>
pcm pins were used insted of spi pins. This patch fixes an issue.
Thanks to Daniel Schwierzeck for noticing it.
Fixes: 3ffeb17a9a ("pinctrl: airoha: add support for Airoha AN7583 PINs")
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Signed-off-by: Linus Walleij <linusw@kernel.org>
an7583_mdio_pins[] pointed at pins 43/44 (I2C1_SDA/I2C1_SCL) instead of
pins 53/54 (MDC_0/MDIO_0 respectively GPIO 51/52). Also the MDIO function
group wrote GPIO_SGMII_MDIO_MODE_MASK (bit 13 of REG_GPIO_PON_MODE, an
unrelated SGMII MDIO mode) and GPIO_MDC_IO_MASTER_MODE_MODE (BIT(14),
an EN7581 specific bit from REG_GPIO_2ND_I2C_MODE).
Fix both by setting an7583_mdio_pins[] to { 53, 54 } and rewriting the
function group to clear AN7583_MDC_0_GPIO_MODE_MASK (bit 25) and
AN7583_MDIO_0_GPIO_MODE_MASK (bit 26) of REG_GPIO_PON_MODE. Both bits
are cleared by the hwinit at probe.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
On AN7583 both I2C busses have a pin sharing with GPIO. Also the pin mux
setting is done in REG_GPIO_PON_MODE instead of REG_GPIO_2ND_I2C_MODE.
Add dedicated I2C pin groups and function groups for AN7583. The new
groups must support i2c0 and i2c1.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
The pin mux on GPIOs 1 and 2 on AN7581 supports I2C in master and
slave mode. When selecting I2C the according bits (bit 13 for master,
bit 11 for slave) must be set in REG_GPIO_2ND_I2C_MODE.
Fix the i2c1 pin group to set bits 0 and 13 to set I2C1 master mode by
default.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
Current an7583 pinmux implementation have following issues:
* pins 51 and 52 can't be set as pcie_reset, current pcie_reset code
will sets pins to gpio mode instead.
* there is no proper way to set pins 41--54 to gpio mode.
* pins 41--53 can't be actually set as pwm pins. These pins must be
muxed to gpio mode as well.
This patch fixes above issues.
Fixes: 3ffeb17a9a ("pinctrl: airoha: add support for Airoha AN7583 PINs")
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Signed-off-by: Linus Walleij <linusw@kernel.org>
In the an7581 case
* gpio47 and pcie_reset0 shares pin 60,
* gpio48 and pcie_reset1 shares pin 61,
* gpio49 and pcie_reset2 shares pin 62.
but current driver treat them as pins 61--63. This is wrong.
Also current an7581 pinmux implementation have following issues:
* current pcie_reset pin function actually sets corresponding
pins as gpios.
* there is no proper way to set pcie_reset pins as gpios.
* there is no way to set pcie_reset pins as pwm.
This patch fixes above issues.
WARNING:
There is a contradiction in the Airoha documentation. AN7581 programming
guide claims:
- gpio44 and pcie_reset0 shares the same pin
- gpio45 and pcie_reset1 shares the same pin
- gpio46 and pcie_reset2 shares the same pin
While AN7581 datasheet claims:
- gpio47 and pcie_reset0 shares the same pin
- gpio48 and pcie_reset1 shares the same pin
- gpio49 and pcie_reset2 shares the same pin
The datasheet should be considered as a more reliable source.
Thanks to Benjamin Larsson for clarification.
Fixes: 1c8ace2d07 ("pinctrl: airoha: Add support for EN7581 SoC")
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Signed-off-by: Linus Walleij <linusw@kernel.org>
Pinconfs of i2c_sda/i2c_scl pins are swapped, this needs to be fixed.
Fixes: 1c8ace2d07 ("pinctrl: airoha: Add support for EN7581 SoC")
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Signed-off-by: Linus Walleij <linusw@kernel.org>
Fix misprint in mdio bitfield name of GPIO_2ND_I2C_MODE register.
While at it also fix an7583 mdio. It should use an7583 specific
mdio bitfield.
Fixes: 1c8ace2d07 ("pinctrl: airoha: Add support for EN7581 SoC")
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Linus Walleij <linusw@kernel.org>
Use IRQ_TYPE_LEVEL_MASK and IRQ_TYPE_EDGE_BOTH instead of open-coded
trigger type combinations in irqchip callbacks.
No functional change intended.
Assisted-by: Claude:claude-sonnet-5
Signed-off-by: Maulik Shah <maulik.shah@oss.qualcomm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linusw@kernel.org>
pcm_spi_int, pcm_spi_cs2, pcm_spi_cs3, pcm_spi_cs4 pin groups are not
defined, so pcm_spi function can't be applied to these groups.
Fixes: 3ffeb17a9a ("pinctrl: airoha: add support for Airoha AN7583 PINs")
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Signed-off-by: Linus Walleij <linusw@kernel.org>
phy1_led1 pin function wrongly refers to gpio1 instead of gpio11.
Fix it.
Fixes: 3ffeb17a9a ("pinctrl: airoha: add support for Airoha AN7583 PINs")
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Signed-off-by: Linus Walleij <linusw@kernel.org>
gpio22 pin group is missed, fix it.
Fixes: 3ffeb17a9a ("pinctrl: airoha: add support for Airoha AN7583 PINs")
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Signed-off-by: Linus Walleij <linusw@kernel.org>
gpio21 pin group refers to gpio22 pin, this is wrong.
Fixes: 3ffeb17a9a ("pinctrl: airoha: add support for Airoha AN7583 PINs")
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Signed-off-by: Linus Walleij <linusw@kernel.org>
AN7581 have 47 valid GPIOs only (gpio0-gpio46), so gpio47 is a fiction.
AN7583 have 49 valid GPIOs (gpio0-gpio48), so gpio48 is missed
To fix an issue
* create AN7583 specific pwm pin function,
* remove gpio47 from AN7581 pwm pin function.
Fixes: 3ffeb17a9a ("pinctrl: airoha: add support for Airoha AN7583 PINs")
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Signed-off-by: Linus Walleij <linusw@kernel.org>
phy4_led1 pin function maps led incorrectly. It uses the same map as
phy3_led1. PHY{X} should map to LAN{N}_PHY_LED_MAP(X-1).
Fixes: 3ffeb17a9a ("pinctrl: airoha: add support for Airoha AN7583 PINs")
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
phy4_led1 pin function maps led incorrectly. It uses the same map as
phy3_led1. PHY{X} should map to LAN{N}_PHY_LED_MAP(X-1).
Fixes: 579839c954 ("pinctrl: airoha: convert PHY LED GPIO to macro")
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
Pin 21 (gpio19) duplicate pinconf settings of pin 20. Fix it using
a proper bit number in the configuration register.
Fixes: 3ffeb17a9a ("pinctrl: airoha: add support for Airoha AN7583 PINs")
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
Pin 32 (gpio19) duplicate pinconf settings of pin 31. Fix it using
a proper bit number in the configuration register.
Fixes: 1c8ace2d07 ("pinctrl: airoha: Add support for EN7581 SoC")
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
gpio32 pin group is missed for an7583 SoC. This patch add it.
Fixes: 3ffeb17a9a ("pinctrl: airoha: add support for Airoha AN7583 PINs")
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
gpio32 pin group is missed for an7581 SoC. This patch add it.
Fixes: 1c8ace2d07 ("pinctrl: airoha: Add support for EN7581 SoC")
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
In preparation for additional SoC support, move the Airoha pinctrl driver
for AN7581 SoC to a dedicated directory.
This is to tidy things up and keep code organized without polluting the
Mediatek driver directory.
The driver doesn't depend on any generic or common code from the Mediatek
codebase so it can be safely moved without any modification.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Linus Walleij <linusw@kernel.org>
