The PHY counters can be lost if the PHY is reset during suspend. We
need to save the values into the shadow counters or the accounting
will be incorrect over multiple suspend and resume cycles.
Fixes: 820ee17b8d ("net: phy: broadcom: Add support code for reading PHY counters")
Signed-off-by: Justin Chen <justin.chen@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20260505173926.2870069-1-justin.chen@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
LAN8814 QSGMII soft reset was moved into the probe function to avoid
triggering it for each of 4 PHY-s in the package.
However, that broke QSGMII link between the MAC and PHY on most LAN8814
PHY-s, specificaly for us on the Microchip LAN969x switch.
Reading the QSGMII status registers it was visible that lanes were only
partially synced.
It looks like the reset timing is crucial, so lets move the reset back
into the .config_init function but guard it with phy_package_init_once()
to avoid it being triggered on each of 4 PHY-s in the package.
Change the probe function to use phy_package_probe_once() for coma and PtP
setup.
Fixes: 96a9178a29 ("net: phy: micrel: lan8814 fix reset of the QSGMII interface")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Link: https://patch.msgid.link/20260428134138.1741253-1-robert.marko@sartura.hr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Table 7-121 in datasheet says we have to set register 0xc6
to value 0x10 before CLK_O_SEL can be modified. No more infos
about this field found in datasheet. With this fix, setting
of CLK_O_SEL field in IO_MUX_CFG register worked through dts
property "ti,clk-output-sel" on a DP83869HMRGZR.
Signed-off-by: Heiko Schocher <hs@nabladev.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Fixes: 01db923e83 ("net: phy: dp83869: Add TI dp83869 phy")
Link: https://patch.msgid.link/20260425031339.3318-1-hs@nabladev.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Core & protocols
----------------
- Support HW queue leasing, allowing containers to be granted access
to HW queues for zero-copy operations and AF_XDP.
- Number of code moves to help the compiler with inlining.
Avoid output arguments for returning drop reason where possible.
- Rework drop handling within qdiscs to include more metadata
about the reason and dropping qdisc in the tracepoints.
- Remove the rtnl_lock use from IP Multicast Routing.
- Pack size information into the Rx Flow Steering table pointer
itself. This allows making the table itself a flat array of u32s,
thus making the table allocation size a power of two.
- Report TCP delayed ack timer information via socket diag.
- Add ip_local_port_step_width sysctl to allow distributing the randomly
selected ports more evenly throughout the allowed space.
- Add support for per-route tunsrc in IPv6 segment routing.
- Start work of switching sockopt handling to iov_iter.
- Improve dynamic recvbuf sizing in MPTCP, limit burstiness and avoid
buffer size drifting up.
- Support MSG_EOR in MPTCP.
- Add stp_mode attribute to the bridge driver for STP mode selection.
This addresses concerns about call_usermodehelper() usage.
- Remove UDP-Lite support (as announced in 2023).
- Remove support for building IPv6 as a module.
Remove the now unnecessary function calling indirection.
Cross-tree stuff
----------------
- Move Michael MIC code from generic crypto into wireless,
it's considered insecure but some WiFi networks still need it.
Netfilter
---------
- Switch nft_fib_ipv6 module to no longer need temporary dst_entry
object allocations by using fib6_lookup() + RCU.
Florian W reports this gets us ~13% higher packet rate.
- Convert IPVS's global __ip_vs_mutex to per-net service_mutex and
switch the service tables to be per-net. Convert some code that
walks the service lists to use RCU instead of the service_mutex.
- Add more opinionated input validation to lower security exposure.
- Make IPVS hash tables to be per-netns and resizable.
Wireless
--------
- Finished assoc frame encryption/EPPKE/802.1X-over-auth.
- Radar detection improvements.
- Add 6 GHz incumbent signal detection APIs.
- Multi-link support for FILS, probe response templates and
client probing.
- New APIs and mac80211 support for NAN (Neighbor Aware Networking,
aka Wi-Fi Aware) so less work must be in firmware.
Driver API
----------
- Add numerical ID for devlink instances (to avoid having to create
fake bus/device pairs just to have an ID). Support shared devlink
instances which span multiple PFs.
- Add standard counters for reporting pause storm events
(implement in mlx5 and fbnic).
- Add configuration API for completion writeback buffering
(implement in mana).
- Support driver-initiated change of RSS context sizes.
- Support DPLL monitoring input frequency (implement in zl3073x).
- Support per-port resources in devlink (implement in mlx5).
Misc
----
- Expand the YAML spec for Netfilter.
Drivers
-------
- Software:
- macvlan: support multicast rx for bridge ports with shared source
MAC address
- team: decouple receive and transmit enablement for IEEE 802.3ad
LACP "independent control"
- Ethernet high-speed NICs:
- nVidia/Mellanox:
- support high order pages in zero-copy mode (for payload
coalescing)
- support multiple packets in a page (for systems with 64kB pages)
- Broadcom 25-400GE (bnxt):
- implement XDP RSS hash metadata extraction
- add software fallback for UDP GSO, lowering the IOMMU cost
- Broadcom 800GE (bnge):
- add link status and configuration handling
- add various HW and SW statistics
- Marvell/Cavium:
- NPC HW block support for cn20k
- Huawei (hinic3):
- add mailbox / control queue
- add rx VLAN offload
- add driver info and link management
- Ethernet NICs:
- Marvell/Aquantia:
- support reading SFP module info on some AQC100 cards
- Realtek PCI (r8169):
- add support for RTL8125cp
- Realtek USB (r8152):
- support for the RTL8157 5Gbit chip
- add 2500baseT EEE status/configuration support
- Ethernet NICs embedded and off-the-shelf IP:
- Synopsys (stmmac):
- cleanup and reorganize SerDes handling and PCS support
- cleanup descriptor handling and per-platform data
- cleanup and consolidate MDIO defines and handling
- shrink driver memory use for internal structures
- improve Tx IRQ coalescing
- improve TCP segmentation handling
- add support for Spacemit K3
- Cadence (macb):
- support PHYs that have inband autoneg disabled with GEM
- support IEEE 802.3az EEE
- rework usrio capabilities and handling
- AMD (xgbe):
- improve power management for S0i3
- improve TX resilience for link-down handling
- Virtual:
- Google cloud vNIC:
- support larger ring sizes in DQO-QPL mode
- improve HW-GRO handling
- support UDP GSO for DQO format
- PCIe NTB:
- support queue count configuration
- Ethernet PHYs:
- automatically disable PHY autonomous EEE if MAC is in charge
- Broadcom:
- add BCM84891/BCM84892 support
- Micrel:
- support for LAN9645X internal PHY
- Realtek:
- add RTL8224 pair order support
- support PHY LEDs on RTL8211F-VD
- support spread spectrum clocking (SSC)
- Maxlinear:
- add PHY-level statistics via ethtool
- Ethernet switches:
- Maxlinear (mxl862xx):
- support for bridge offloading
- support for VLANs
- support driver statistics
- Bluetooth:
- large number of fixes and new device IDs
- Mediatek:
- support MT6639 (MT7927)
- support MT7902 SDIO
- WiFi:
- Intel (iwlwifi):
- UNII-9 and continuing UHR work
- MediaTek (mt76):
- mt7996/mt7925 MLO fixes/improvements
- mt7996 NPU support (HW eth/wifi traffic offload)
- Qualcomm (ath12k):
- monitor mode support on IPQ5332
- basic hwmon temperature reporting
- support IPQ5424
- Realtek:
- add USB RX aggregation to improve performance
- add USB TX flow control by tracking in-flight URBs
- Cellular:
- IPA v5.2 support
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=EhQZ
-----END PGP SIGNATURE-----
Merge tag 'net-next-7.1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core & protocols:
- Support HW queue leasing, allowing containers to be granted access
to HW queues for zero-copy operations and AF_XDP
- Number of code moves to help the compiler with inlining. Avoid
output arguments for returning drop reason where possible
- Rework drop handling within qdiscs to include more metadata about
the reason and dropping qdisc in the tracepoints
- Remove the rtnl_lock use from IP Multicast Routing
- Pack size information into the Rx Flow Steering table pointer
itself. This allows making the table itself a flat array of u32s,
thus making the table allocation size a power of two
- Report TCP delayed ack timer information via socket diag
- Add ip_local_port_step_width sysctl to allow distributing the
randomly selected ports more evenly throughout the allowed space
- Add support for per-route tunsrc in IPv6 segment routing
- Start work of switching sockopt handling to iov_iter
- Improve dynamic recvbuf sizing in MPTCP, limit burstiness and avoid
buffer size drifting up
- Support MSG_EOR in MPTCP
- Add stp_mode attribute to the bridge driver for STP mode selection.
This addresses concerns about call_usermodehelper() usage
- Remove UDP-Lite support (as announced in 2023)
- Remove support for building IPv6 as a module. Remove the now
unnecessary function calling indirection
Cross-tree stuff:
- Move Michael MIC code from generic crypto into wireless, it's
considered insecure but some WiFi networks still need it
Netfilter:
- Switch nft_fib_ipv6 module to no longer need temporary dst_entry
object allocations by using fib6_lookup() + RCU.
Florian W reports this gets us ~13% higher packet rate
- Convert IPVS's global __ip_vs_mutex to per-net service_mutex and
switch the service tables to be per-net. Convert some code that
walks the service lists to use RCU instead of the service_mutex
- Add more opinionated input validation to lower security exposure
- Make IPVS hash tables to be per-netns and resizable
Wireless:
- Finished assoc frame encryption/EPPKE/802.1X-over-auth
- Radar detection improvements
- Add 6 GHz incumbent signal detection APIs
- Multi-link support for FILS, probe response templates and client
probing
- New APIs and mac80211 support for NAN (Neighbor Aware Networking,
aka Wi-Fi Aware) so less work must be in firmware
Driver API:
- Add numerical ID for devlink instances (to avoid having to create
fake bus/device pairs just to have an ID). Support shared devlink
instances which span multiple PFs
- Add standard counters for reporting pause storm events (implement
in mlx5 and fbnic)
- Add configuration API for completion writeback buffering (implement
in mana)
- Support driver-initiated change of RSS context sizes
- Support DPLL monitoring input frequency (implement in zl3073x)
- Support per-port resources in devlink (implement in mlx5)
Misc:
- Expand the YAML spec for Netfilter
Drivers
- Software:
- macvlan: support multicast rx for bridge ports with shared
source MAC address
- team: decouple receive and transmit enablement for IEEE 802.3ad
LACP "independent control"
- Ethernet high-speed NICs:
- nVidia/Mellanox:
- support high order pages in zero-copy mode (for payload
coalescing)
- support multiple packets in a page (for systems with 64kB
pages)
- Broadcom 25-400GE (bnxt):
- implement XDP RSS hash metadata extraction
- add software fallback for UDP GSO, lowering the IOMMU cost
- Broadcom 800GE (bnge):
- add link status and configuration handling
- add various HW and SW statistics
- Marvell/Cavium:
- NPC HW block support for cn20k
- Huawei (hinic3):
- add mailbox / control queue
- add rx VLAN offload
- add driver info and link management
- Ethernet NICs:
- Marvell/Aquantia:
- support reading SFP module info on some AQC100 cards
- Realtek PCI (r8169):
- add support for RTL8125cp
- Realtek USB (r8152):
- support for the RTL8157 5Gbit chip
- add 2500baseT EEE status/configuration support
- Ethernet NICs embedded and off-the-shelf IP:
- Synopsys (stmmac):
- cleanup and reorganize SerDes handling and PCS support
- cleanup descriptor handling and per-platform data
- cleanup and consolidate MDIO defines and handling
- shrink driver memory use for internal structures
- improve Tx IRQ coalescing
- improve TCP segmentation handling
- add support for Spacemit K3
- Cadence (macb):
- support PHYs that have inband autoneg disabled with GEM
- support IEEE 802.3az EEE
- rework usrio capabilities and handling
- AMD (xgbe):
- improve power management for S0i3
- improve TX resilience for link-down handling
- Virtual:
- Google cloud vNIC:
- support larger ring sizes in DQO-QPL mode
- improve HW-GRO handling
- support UDP GSO for DQO format
- PCIe NTB:
- support queue count configuration
- Ethernet PHYs:
- automatically disable PHY autonomous EEE if MAC is in charge
- Broadcom:
- add BCM84891/BCM84892 support
- Micrel:
- support for LAN9645X internal PHY
- Realtek:
- add RTL8224 pair order support
- support PHY LEDs on RTL8211F-VD
- support spread spectrum clocking (SSC)
- Maxlinear:
- add PHY-level statistics via ethtool
- Ethernet switches:
- Maxlinear (mxl862xx):
- support for bridge offloading
- support for VLANs
- support driver statistics
- Bluetooth:
- large number of fixes and new device IDs
- Mediatek:
- support MT6639 (MT7927)
- support MT7902 SDIO
- WiFi:
- Intel (iwlwifi):
- UNII-9 and continuing UHR work
- MediaTek (mt76):
- mt7996/mt7925 MLO fixes/improvements
- mt7996 NPU support (HW eth/wifi traffic offload)
- Qualcomm (ath12k):
- monitor mode support on IPQ5332
- basic hwmon temperature reporting
- support IPQ5424
- Realtek:
- add USB RX aggregation to improve performance
- add USB TX flow control by tracking in-flight URBs
- Cellular:
- IPA v5.2 support"
* tag 'net-next-7.1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1561 commits)
net: pse-pd: fix kernel-doc function name for pse_control_find_by_id()
wireguard: device: use exit_rtnl callback instead of manual rtnl_lock in pre_exit
wireguard: allowedips: remove redundant space
tools: ynl: add sample for wireguard
wireguard: allowedips: Use kfree_rcu() instead of call_rcu()
MAINTAINERS: Add netkit selftest files
selftests/net: Add additional test coverage in nk_qlease
selftests/net: Split netdevsim tests from HW tests in nk_qlease
tools/ynl: Make YnlFamily closeable as a context manager
net: airoha: Add missing PPE configurations in airoha_ppe_hw_init()
net: airoha: Fix VIP configuration for AN7583 SoC
net: caif: clear client service pointer on teardown
net: strparser: fix skb_head leak in strp_abort_strp()
net: usb: cdc-phonet: fix skb frags[] overflow in rx_complete()
selftests/bpf: add test for xdp_master_redirect with bond not up
net, bpf: fix null-ptr-deref in xdp_master_redirect() for down master
net: airoha: Remove PCE_MC_EN_MASK bit in REG_FE_PCE_CFG configuration
sctp: disable BH before calling udp_tunnel_xmit_skb()
sctp: fix missing encap_port propagation for GSO fragments
net: airoha: Rely on net_device pointer in ETS callbacks
...
Merge in late fixes in preparation for the net-next PR.
Conflicts:
include/net/sch_generic.h
a6bd339dbb ("net_sched: fix skb memory leak in deferred qdisc drops")
ff2998f29f ("net: sched: introduce qdisc-specific drop reason tracing")
https://lore.kernel.org/adz0iX85FHMz0HdO@sirena.org.uk
drivers/net/ethernet/airoha/airoha_eth.c
1acdfbdb51 ("net: airoha: Fix VIP configuration for AN7583 SoC")
bf3471e6e6 ("net: airoha: Make flow control source port mapping dependent on nbq parameter")
Adjacent changes:
drivers/net/ethernet/airoha/airoha_ppe.c
f44218cd5e ("net: airoha: Reset PPE cpu port configuration in airoha_ppe_hw_init()")
7da62262ec ("inet: add ip_local_port_step_width sysctl to improve port usage distribution")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
- debugfs:
- Fix NULL pointer dereference in debugfs_create_str()
- Fix misplaced EXPORT_SYMBOL_GPL for debugfs_create_str()
- Fix soundwire debugfs NULL pointer dereference from uninitialized
firmware_file
- device property:
- Make fwnode flags modifications thread safe; widen the field to
unsigned long and use set_bit() / clear_bit() based accessors
- Document how to check for the property presence
- devres:
- Separate struct devres_node from its "subclasses" (struct devres,
struct devres_group); give struct devres_node its own release and
free callbacks for per-type dispatch
- Introduce struct devres_action for devres actions, avoiding the
ARCH_DMA_MINALIGN alignment overhead of struct devres
- Export struct devres_node and its init/add/remove/dbginfo
primitives for use by Rust Devres<T>
- Fix missing node debug info in devm_krealloc()
- Use guard(spinlock_irqsave) where applicable; consolidate unlock
paths in devres_release_group()
- driver_override:
- Convert PCI, WMI, vdpa, s390/cio, s390/ap, and fsl-mc to the
generic driver_override infrastructure, replacing per-bus
driver_override strings, sysfs attributes, and match logic; fixes
a potential UAF from unsynchronized access to driver_override in
bus match() callbacks
- Simplify __device_set_driver_override() logic
- kernfs:
- Send IN_DELETE_SELF and IN_IGNORED inotify events on kernfs
file and directory removal
- Add corresponding selftests for memcg
- platform:
- Allow attaching software nodes when creating platform devices via
a new 'swnode' field in struct platform_device_info
- Add kerneldoc for struct platform_device_info
- software node:
- Move software node initialization from postcore_initcall() to
driver_init(), making it available early in the boot process
- Move kernel_kobj initialization (ksysfs_init) earlier to support
the above
- Remove software_node_exit(); dead code in a built-in unit
- SoC:
- Introduce of_machine_read_compatible() and of_machine_read_model()
OF helpers and export soc_attr_read_machine() to replace direct
accesses to of_root from SoC drivers; also enables
CONFIG_COMPILE_TEST coverage for these drivers
- sysfs:
- Constify attribute group array pointers to
'const struct attribute_group *const *' in sysfs functions,
device_add_groups() / device_remove_groups(), and struct class
- Rust:
- Devres:
- Embed struct devres_node directly in Devres<T> instead of going
through devm_add_action(), avoiding the extra allocation and
the unnecessary ARCH_DMA_MINALIGN alignment
- I/O:
- Turn IoCapable from a marker trait into a functional trait
carrying the raw I/O accessor implementation (io_read /
io_write), providing working defaults for the per-type Io
methods
- Add RelaxedMmio wrapper type, making relaxed accessors usable
in code generic over the Io trait
- Remove overloaded per-type Io methods and per-backend macros
from Mmio and PCI ConfigSpace
- I/O (Register):
- Add IoLoc trait and generic read/write/update methods to the Io
trait, making I/O operations parameterizable by typed locations
- Add register! macro for defining hardware register types with
typed bitfield accessors backed by Bounded values; supports
direct, relative, and array register addressing
- Add write_reg() / try_write_reg() and LocatedRegister trait
- Update PCI sample driver to demonstrate the register! macro
Example:
```
register! {
/// UART control register.
CTRL(u32) @ 0x18 {
/// Receiver enable.
19:19 rx_enable => bool;
/// Parity configuration.
14:13 parity ?=> Parity;
}
/// FIFO watermark and counter register.
WATER(u32) @ 0x2c {
/// Number of datawords in the receive FIFO.
26:24 rx_count;
/// RX interrupt threshold.
17:16 rx_water;
}
}
impl WATER {
fn rx_above_watermark(&self) -> bool {
self.rx_count() > self.rx_water()
}
}
fn init(bar: &pci::Bar<BAR0_SIZE>) {
let water = WATER::zeroed()
.with_const_rx_water::<1>(); // > 3 would not compile
bar.write_reg(water);
let ctrl = CTRL::zeroed()
.with_parity(Parity::Even)
.with_rx_enable(true);
bar.write_reg(ctrl);
}
fn handle_rx(bar: &pci::Bar<BAR0_SIZE>) {
if bar.read(WATER).rx_above_watermark() {
// drain the FIFO
}
}
fn set_parity(bar: &pci::Bar<BAR0_SIZE>, parity: Parity) {
bar.update(CTRL, |r| r.with_parity(parity));
}
```
- IRQ:
- Move 'static bounds from where clauses to trait declarations
for IRQ handler traits
- Misc:
- Enable the generic_arg_infer Rust feature
- Extend Bounded with shift operations, single-bit bool conversion,
and const get()
- Misc:
- Make deferred_probe_timeout default a Kconfig option
- Drop auxiliary_dev_pm_ops; the PM core falls back to driver PM
callbacks when no bus type PM ops are set
- Add conditional guard support for device_lock()
- Add ksysfs.c to the DRIVER CORE MAINTAINERS entry
- Fix kernel-doc warnings in base.h
- Fix stale reference to memory_block_add_nid() in documentation
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQS2q/xV6QjXAdC7k+1FlHeO1qrKLgUCadl5SwAKCRBFlHeO1qrK
LpjDAQCSG3vYznwrngfpmRU5bCB9sdUy/pZiX5px1357+amJkwEA9LgIVQvtHAZW
ZXcQ7Jr+mR3mJEdlatbkWHp3w1VHqAQ=
=y1DV
-----END PGP SIGNATURE-----
Merge tag 'driver-core-7.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/driver-core/driver-core
Pull driver core updates from Danilo Krummrich:
"debugfs:
- Fix NULL pointer dereference in debugfs_create_str()
- Fix misplaced EXPORT_SYMBOL_GPL for debugfs_create_str()
- Fix soundwire debugfs NULL pointer dereference from uninitialized
firmware_file
device property:
- Make fwnode flags modifications thread safe; widen the field to
unsigned long and use set_bit() / clear_bit() based accessors
- Document how to check for the property presence
devres:
- Separate struct devres_node from its "subclasses" (struct devres,
struct devres_group); give struct devres_node its own release and
free callbacks for per-type dispatch
- Introduce struct devres_action for devres actions, avoiding the
ARCH_DMA_MINALIGN alignment overhead of struct devres
- Export struct devres_node and its init/add/remove/dbginfo
primitives for use by Rust Devres<T>
- Fix missing node debug info in devm_krealloc()
- Use guard(spinlock_irqsave) where applicable; consolidate unlock
paths in devres_release_group()
driver_override:
- Convert PCI, WMI, vdpa, s390/cio, s390/ap, and fsl-mc to the
generic driver_override infrastructure, replacing per-bus
driver_override strings, sysfs attributes, and match logic; fixes a
potential UAF from unsynchronized access to driver_override in bus
match() callbacks
- Simplify __device_set_driver_override() logic
kernfs:
- Send IN_DELETE_SELF and IN_IGNORED inotify events on kernfs file
and directory removal
- Add corresponding selftests for memcg
platform:
- Allow attaching software nodes when creating platform devices via a
new 'swnode' field in struct platform_device_info
- Add kerneldoc for struct platform_device_info
software node:
- Move software node initialization from postcore_initcall() to
driver_init(), making it available early in the boot process
- Move kernel_kobj initialization (ksysfs_init) earlier to support
the above
- Remove software_node_exit(); dead code in a built-in unit
SoC:
- Introduce of_machine_read_compatible() and of_machine_read_model()
OF helpers and export soc_attr_read_machine() to replace direct
accesses to of_root from SoC drivers; also enables
CONFIG_COMPILE_TEST coverage for these drivers
sysfs:
- Constify attribute group array pointers to
'const struct attribute_group *const *' in sysfs functions,
device_add_groups() / device_remove_groups(), and struct class
Rust:
- Devres:
- Embed struct devres_node directly in Devres<T> instead of going
through devm_add_action(), avoiding the extra allocation and the
unnecessary ARCH_DMA_MINALIGN alignment
- I/O:
- Turn IoCapable from a marker trait into a functional trait
carrying the raw I/O accessor implementation (io_read /
io_write), providing working defaults for the per-type Io
methods
- Add RelaxedMmio wrapper type, making relaxed accessors usable in
code generic over the Io trait
- Remove overloaded per-type Io methods and per-backend macros
from Mmio and PCI ConfigSpace
- I/O (Register):
- Add IoLoc trait and generic read/write/update methods to the Io
trait, making I/O operations parameterizable by typed locations
- Add register! macro for defining hardware register types with
typed bitfield accessors backed by Bounded values; supports
direct, relative, and array register addressing
- Add write_reg() / try_write_reg() and LocatedRegister trait
- Update PCI sample driver to demonstrate the register! macro
Example:
```
register! {
/// UART control register.
CTRL(u32) @ 0x18 {
/// Receiver enable.
19:19 rx_enable => bool;
/// Parity configuration.
14:13 parity ?=> Parity;
}
/// FIFO watermark and counter register.
WATER(u32) @ 0x2c {
/// Number of datawords in the receive FIFO.
26:24 rx_count;
/// RX interrupt threshold.
17:16 rx_water;
}
}
impl WATER {
fn rx_above_watermark(&self) -> bool {
self.rx_count() > self.rx_water()
}
}
fn init(bar: &pci::Bar<BAR0_SIZE>) {
let water = WATER::zeroed()
.with_const_rx_water::<1>(); // > 3 would not compile
bar.write_reg(water);
let ctrl = CTRL::zeroed()
.with_parity(Parity::Even)
.with_rx_enable(true);
bar.write_reg(ctrl);
}
fn handle_rx(bar: &pci::Bar<BAR0_SIZE>) {
if bar.read(WATER).rx_above_watermark() {
// drain the FIFO
}
}
fn set_parity(bar: &pci::Bar<BAR0_SIZE>, parity: Parity) {
bar.update(CTRL, |r| r.with_parity(parity));
}
```
- IRQ:
- Move 'static bounds from where clauses to trait declarations for
IRQ handler traits
- Misc:
- Enable the generic_arg_infer Rust feature
- Extend Bounded with shift operations, single-bit bool
conversion, and const get()
Misc:
- Make deferred_probe_timeout default a Kconfig option
- Drop auxiliary_dev_pm_ops; the PM core falls back to driver PM
callbacks when no bus type PM ops are set
- Add conditional guard support for device_lock()
- Add ksysfs.c to the DRIVER CORE MAINTAINERS entry
- Fix kernel-doc warnings in base.h
- Fix stale reference to memory_block_add_nid() in documentation"
* tag 'driver-core-7.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/driver-core/driver-core: (67 commits)
bus: fsl-mc: use generic driver_override infrastructure
s390/ap: use generic driver_override infrastructure
s390/cio: use generic driver_override infrastructure
vdpa: use generic driver_override infrastructure
platform/wmi: use generic driver_override infrastructure
PCI: use generic driver_override infrastructure
driver core: make software nodes available earlier
software node: remove software_node_exit()
kernel: ksysfs: initialize kernel_kobj earlier
MAINTAINERS: add ksysfs.c to the DRIVER CORE entry
drivers/base/memory: fix stale reference to memory_block_add_nid()
device property: Document how to check for the property presence
soundwire: debugfs: initialize firmware_file to empty string
debugfs: fix placement of EXPORT_SYMBOL_GPL for debugfs_create_str()
debugfs: check for NULL pointer in debugfs_create_str()
driver core: Make deferred_probe_timeout default a Kconfig option
driver core: simplify __device_set_driver_override() clearing logic
driver core: auxiliary bus: Drop auxiliary_dev_pm_ops
device property: Make modifications of fwnode "flags" thread safe
rust: devres: embed struct devres_node directly
...
Replace the magic number with an existing define for the LEDCR
register page number on the RTL8211F.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Link: https://patch.msgid.link/20260411105150.184577-1-olek2@wp.pl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As noted in the blamed commit, the AR8035 and other PHYs from this
family advertise the Extended Next Page support by default, which may be
understood by some partners as this PHY being multi-gig capable.
The fix is to disable XNP advertising, which is done by setting bit 12
of the Auto-Negotiation Advertisement Register (MII_ADVERTISE).
The blamed commit incorrectly uses MDIO_AN_CTRL1_XNP, which is bit 13 as per
802.3 : 45.2.7.1 AN control register (Register 7.0)
BIT 12 in MII_ADVERTISE is wrapped by ADVERTISE_RESV, used by some
drivers such as the aquantia one. 802.3 Clause 28 defines bit 12 as
Extended Next Page ability, at least in recent versions of the standard.
Let's add a define for it and use it in the at803x driver.
Fixes: 3c51fa5d2a ("net: phy: ar803x: disable extended next page bit")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260410171021.1277138-1-maxime.chevallier@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
MDIO bus controllers are not required to wait for write transactions to
complete before returning as synchronization is often achieved by polling
status bits.
This can cause issues when disabling interrupts since an interrupt could
fire before the interrupt handler is unregistered and there's no status
bit to poll.
Add a phy_write_barrier() function and use it in phy_disable_interrupts()
to fix this issue. The write barrier just reads an MII register and
discards the value, which is enough to guarantee that previous writes have
completed.
Signed-off-by: Charles Perry <charles.perry@microchip.com>
Link: https://patch.msgid.link/20260408131821.1145334-4-charles.perry@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The return value of phy_c45_probe_present() is stored in "ret", not
"phy_reg", fix this. "phy_reg" always has a positive value if we reach
this return path (since it would have returned earlier otherwise), which
means that the original goal of the patch of not considering -ENODEV
fatal wasn't achieved.
Fixes: 17b4475394 ("net: phy: c45 scanning: Don't consider -ENODEV fatal")
Signed-off-by: Charles Perry <charles.perry@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/20260409133654.3203336-1-charles.perry@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The RTL8211F previously unconditionally disabled PHY-mode EEE in
config_init. Convert this to use the new .disable_autonomous_eee
callback so it is only disabled when the MAC indicates EEE support
via phy_support_eee().
This preserves PHY-autonomous EEE for MACs that do not support EEE,
while still disabling it when the MAC manages LPI.
Signed-off-by: Nicolai Buchwitz <nb@tipi-net.de>
Link: https://patch.msgid.link/20260406-devel-autonomous-eee-v1-3-b335e7143711@tipi-net.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement the .disable_autonomous_eee callback for the BCM54210E.
In AutogrEEEn mode the PHY manages EEE autonomously. Clearing the
AutogrEEEn enable bit in MII_BUF_CNTL_0 switches the PHY to Native
EEE mode.
Signed-off-by: Nicolai Buchwitz <nb@tipi-net.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20260406-devel-autonomous-eee-v1-2-b335e7143711@tipi-net.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some PHYs (e.g. Broadcom BCM54xx, Realtek RTL8211F) implement
autonomous EEE where the PHY manages LPI signaling without forwarding
it to the MAC. This conflicts with MAC drivers that implement their own
LPI control.
Add a .disable_autonomous_eee callback to struct phy_driver and call it
from phy_support_eee(). When a MAC driver indicates it supports EEE via
phy_support_eee(), the PHY's autonomous EEE is automatically disabled so
the MAC can manage LPI entry/exit.
Signed-off-by: Nicolai Buchwitz <nb@tipi-net.de>
Link: https://patch.msgid.link/20260406-devel-autonomous-eee-v1-1-b335e7143711@tipi-net.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for spread spectrum clocking (SSC) on RTL8211F(D)(I)-CG,
RTL8211FS(I)(-VS)-CG, RTL8211FG(I)(-VS)-CG PHYs. The implementation
follows EMI improvement application note Rev. 1.2 for these PHYs.
The current implementation enables SSC for both RXC and SYSCLK clock
signals. Introduce DT properties 'realtek,clkout-ssc-enable',
'realtek,rxc-ssc-enable' and 'realtek,sysclk-ssc-enable' which control
CLKOUT, RXC and SYSCLK SSC spread spectrum clocking enablement on these
signals.
Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
Link: https://patch.msgid.link/20260405233008.148974-3-marek.vasut@mailbox.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace the magic numbers with defines. Register names were obtained from
publicly available documentation[1]. This should make it clear what's going
on in the code.
1. RTL8201F/RTL8201FL/RTL8201FN Rev. 1.4 Datasheet
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Nicolai Buchwitz nb@tipi-net.de
Link: https://patch.msgid.link/20260406201222.1043396-1-olek2@wp.pl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Several GPON ONT SFP sticks based on Realtek RTL960x report
1000BASE-LX at 1300MBd in their EEPROM but can operate at 2500base-X.
On hosts capable of 2500base-X (e.g. Banana Pi R3 / MT7986), the
kernel negotiates only 1G because it trusts the incorrect EEPROM data.
Add quirks for:
- Hisense-Leox LXT-010S-H
- Hisense ZNID-GPON-2311NA
- HSGQ HSGQ-XPON-Stick
Each quirk advertises 2500base-X and ignores TX_FAULT during the
module's ~40s Linux boot time.
Tested on Banana Pi R3 (MT7986) with OpenWrt 25.12.1, confirmed
2.5Gbps link and full throughput with flow offloading.
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Suggested-by: Marcin Nita <marcin.nita@leolabs.pl>
Signed-off-by: John Pavlick <jspavlick@posteo.net>
Link: https://patch.msgid.link/20260406132321.72563-1-jspavlick@posteo.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Enable auto-downshift from 1000BASE-T to 100BASE-TX after 2 failed
auto-negotiation attempts by default. This ensures that links with
faulty or missing cable pairs (C and D) fall back to 100Mbps without
requiring userspace configuration.
The downshift count is stored in the driver's private data and applied
in config_init, so user changes via ethtool are preserved across
suspend/resume cycles.
Users can override or disable downshift at runtime:
ethtool --set-phy-tunable eth0 downshift off
Signed-off-by: Nicolai Buchwitz <nb@tipi-net.de>
Link: https://patch.msgid.link/20260401123848.696766-3-nb@tipi-net.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement the standard ETHTOOL_PHY_DOWNSHIFT tunable for the LAN88xx
PHY. This allows runtime configuration of the auto-downshift feature
via ethtool:
ethtool --set-phy-tunable eth0 downshift on count 3
The LAN88xx PHY supports downshifting from 1000BASE-T to 100BASE-TX
after 2-5 failed auto-negotiation attempts. Valid count values are
2, 3, 4 and 5.
This is based on an earlier downstream implementation by Phil Elwell.
Signed-off-by: Nicolai Buchwitz <nb@tipi-net.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/20260401123848.696766-2-nb@tipi-net.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Expose LED1 and LED2 pins via the PHY LED framework. Each pin has a
source mask (MASK_LOW + MASK_EXT registers) selecting which hardware
events light it, plus a CTL field in the shared 0xA83B register
(RMW; LED4 is firmware-controlled per the datasheet).
Hardware can offload per-speed link triggers (1000/2500/5000/10000),
RX/TX activity, and force-on. LINK_100 is accepted only alongside
LINK_1000: source bit 4 lights at both speeds and 100-alone isn't
representable, so the unrepresentable case falls to software.
The chip has five LED pins; only LED1/LED2 are exposed here as those
are the only ones characterized on tested hardware. LED4 is firmware-
controlled regardless of strap configuration.
Tested on TRENDnet TEG-S750 (LED1/LED2 wired to an antiparallel
bicolor LED): brightness_set via sysfs; netdev trigger offloaded=1
with amber lit at 100M/1G/2.5G and green lit at 10G via respective
link_* modes; LED off immediately on cable unplug with no software
involvement.
Signed-off-by: Daniel Wagner <wagner.daniel.t@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260401114931.3091818-1-wagner.daniel.t@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The BCM84891 and BCM84892 are 10GBASE-T PHYs in the same family as the
BCM84881, sharing the register map and most callbacks. They add USXGMII
as a host interface mode.
bcm8489x_config_init() is separate from bcm84881_config_init(): it
allows only USXGMII (the only host mode available on the tested
hardware) and clears MDIO_CTRL1_LPOWER, which is set at boot on the
tested platform. Does not recur on ifdown/ifup, cable events, or
link-partner advertisement changes, so config_init is sufficient.
For USXGMII, read_status() skips the 0x4011 host-mode register: it
returns the same value regardless of negotiated copper speed (USXGMII
symbol replication). Speed comes from phy_resolve_aneg_linkmode() via
standard C45 AN resolution.
Tested on TRENDnet TEG-S750 (RTL9303 + 1x BCM84891 + 4x BCM84892)
running OpenWrt, where the MDIO controller driver is currently
OpenWrt-specific. Link verified at 100M, 1G, 2.5G, 10G.
Signed-off-by: Daniel Wagner <wagner.daniel.t@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Nicolai Buchwitz <nb@tipi-net.de>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/20260330225310.2801264-1-wagner.daniel.t@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This is a 2.5G copper module which appears to be based on a Motorcomm
YT8821 PHY. There doesn't seem to be a usable way to to access the PHY
(I2C address 0x56 provides only read-only C22 access, and Rollball is
also not working).
The module does not report the correct extended compliance code for
2.5GBase-T, and instead claims to support SONET OC-48 and Fibre Channel:
Identifier : 0x03 (SFP)
Extended identifier : 0x04 (GBIC/SFP defined by 2-wire interface ID)
Connector : 0x07 (LC)
Transceiver codes : 0x00 0x01 0x00 0x00 0x40 0x40 0x04 0x00 0x00
Transceiver type : FC: Multimode, 50um (M5)
Encoding : 0x05 (SONET Scrambled)
BR Nominal : 2500MBd
Despite this, the kernel still enables the correct 2500Base-X interface
mode. However, for the module to actually work, it is also necessary to
disable inband auto-negotiation.
Enable the existing "sfp_quirk_oem_2_5g" for this module, which handles
that and also sets the bit for 2500Base-T link mode.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/20260329191304.720160-1-jan@3e8.eu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In commit 8110633db4 ("net: sfp-bus: allow SFP quirks to override
Autoneg and pause bits") we moved the setting of Autoneg and pause bits
before the call to SFP quirk when parsing SFP module support.
Since the quirk for Ubiquiti U-Fiber Instant SFP module zeroes the
support bits and sets 1000baseX_Full only, the above mentioned commit
changed the overall computed support from
1000baseX_Full, Autoneg, Pause, Asym_Pause
to just
1000baseX_Full.
This broke the SFP module for mvneta, which requires Autoneg for
1000baseX since commit c762b7fac1 ("net: mvneta: deny disabling
autoneg for 802.3z modes").
Fix this by setting back the Autoneg, Pause and Asym_Pause bits in the
quirk.
Fixes: 8110633db4 ("net: sfp-bus: allow SFP quirks to override Autoneg and pause bits")
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/20260326122038.2489589-1-kabel@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The tests in phylink_expects_phy() and phylink_fwnode_phy_connect() are
identical (by intention). Use phylink_expects_phy() to decide whether
to ignore a call to phylink_fwnode_phy_connect().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/E1w4zHg-0000000DmC4-2oyb@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In various places in the kernel, we modify the fwnode "flags" member
by doing either:
fwnode->flags |= SOME_FLAG;
fwnode->flags &= ~SOME_FLAG;
This type of modification is not thread-safe. If two threads are both
mucking with the flags at the same time then one can clobber the
other.
While flags are often modified while under the "fwnode_link_lock",
this is not universally true.
Create some accessor functions for setting, clearing, and testing the
FWNODE flags and move all users to these accessor functions. New
accessor functions use set_bit() and clear_bit(), which are
thread-safe.
Cc: stable@vger.kernel.org
Fixes: c2c724c868 ("driver core: Add fw_devlink_parse_fwtree()")
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Rafael J. Wysocki (Intel) <rafael@kernel.org>
Reviewed-by: Saravana Kannan <saravanak@kernel.org>
Link: https://patch.msgid.link/20260317090112.v2.1.I0a4d03104ecd5103df3d76f66c8d21b1d15a2e38@changeid
[ Fix fwnode_clear_flag() argument alignment, restore dropped blank
line in fwnode_dev_initialized(), and remove unnecessary parentheses
around fwnode_test_flag() calls. - Danilo ]
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
The locked convenience functions phy_package_read() and
phy_package_write() were removed (as they had no users) by commit
e7f984e925 ("net: phy: move PHY package related code from phy.h
to phy_package.c"). Update the comment to reference the existing
unlocked counterparts __phy_package_read() and __phy_package_write().
Assisted-by: unnamed:deepseek-v3.2 coccinelle
Signed-off-by: Kexin Sun <kexinsun@smail.nju.edu.cn>
Link: https://patch.msgid.link/20260321105825.7221-1-kexinsun@smail.nju.edu.cn
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The RTL8224 has a register to configure the polarity of every pair of
each port. It provides device designers more flexbility when wiring the
chip.
Unfortunately, the register is left in an unknown state after a reset.
Thus on devices where the bootloader don't initialize it, the driver has
to do it to detect and use a link.
The MDI polarity swap can be set in the device tree using the property
enet-phy-pair-polarity. The u32 value is a bitfield where bit[0..3]
control the polarity of pairs A..D.
Signed-off-by: Damien Dejean <dam.dejean@gmail.com>
Link: https://patch.msgid.link/20260318215502.106528-5-dam.dejean@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The RTL8224 has a register to configure a pair swap (from ABCD order to
DCBA) providing PCB designers more flexbility when wiring the chip. The
swap parameter has to be set correctly for each of the 4 ports before
the chip can detect a link.
After a reset, this register is (unfortunately) left in a random state,
thus it has to be initialized. On most of the devices the bootloader
does it once for all and we can rely on the value set, on some other it
is not and the kernel has to do it.
The MDI pair swap can be set in the device tree using the property
enet-phy-pair-order. The property is set to 0 to keep the default order
(ABCD), or 1 to reverse the pairs (DCBA).
Signed-off-by: Damien Dejean <dam.dejean@gmail.com>
Link: https://patch.msgid.link/20260318215502.106528-3-dam.dejean@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add debug for the phy_config_inband() call so we can see which inband
modes are being configured at the PHY.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/E1w2mFk-0000000DXW2-2PR9@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After usage of config symbol MDIO_BUS has been removed from REGMAP_MIO
as last user, the symbol can be removed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/9cdf83e9-470d-45da-8efe-ace0decf0204@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Report PCS receive error counts for all supported GPY115x, GPY2xx and
MxL862xx PHYs.
Accumulate the vendor-specific PHY_ERRCNT read-clear counter
(SEL=RXERR) in .update_stats() and expose it as both IEEE 802.3
SymbolErrorDuringCarrier and generic rx_errors via
.get_phy_stats().
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/0029a2fb29bfdcc26abff828d2e18400067b5c58.1773587924.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This moves definition of mdio_bus class and bus_type to the provider
side, what allows to make them private to libphy.
As a prerequisite MDIO statistics handling is moved to the
provider side as well.
Note: This patch causes a checkpatch error "Macros with complex values
should be enclosed in parentheses" for
MDIO_BUS_STATS_ADDR_ATTR_GROUP. I consider this a false positive
here, in addition the patch just moves existing code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/47b85676-b349-4aa0-a5ef-cd37769a4c69@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Functionality outside libphy shouldn't access mdio_bus_class directly.
So move both functions to the provider side. This is a step towards
making mdio_bus_class private to libphy.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/b6161c64-68ac-4524-82ec-5b7d81b86dbc@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch
- makes mdio_device.c part of libphy
- makes mdio_device_(un)register_reset() static
- moves mdiobus_(un)register_device() from mdio_bus.c to mdio_device.c,
stops exporting both functions and makes them private to phylib
This further decouples the MDIO consumer functionality from libphy.
Note: This makes MDIO driver registration part of phylib, therefore
adjust Kconfig dependencies where needed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/c6dbf9b3-3ca0-434b-ad3a-71fe602ab809@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for VSC8662 reporting its inband capabilities, and also
hook to configure the PHY's inband mode.
This fixes a regression in the macb driver caused by commit
1338cfef1f ("net: macb: fix SGMII with inband aneg disabled")
Cc: stable+noautosel@kernel.org # neither this nor commit under fixes should be backported
Reported-by: Conor Dooley <conor@kernel.org>
Link: https://lore.kernel.org/r/20260304-nebulizer-rounding-40fbc81a2ba1@spud
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fixes: 1338cfef1f ("net: macb: fix SGMII with inband aneg disabled")
Link: https://patch.msgid.link/E1w082O-0000000ChNc-1wDz@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
With the current sfp_fixup_ignore_tx_fault() fixup we ignore the TX_FAULT
signal, but we also need to apply sfp_fixup_ignore_los() in order to be
able to communicate with the module even if the fiber isn't connected for
configuration purposes.
This is needed for all the MA5671a firmwares, excluding the FS modded
firmware.
Fixes: 2069624dac ("net: sfp: Add tx-fault workaround for Huawei MA5671A SFP ONT")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260306125139.213637-1-noltari@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This reverts commit 1afccc5a20.
As reported by Marek the change causes a warning on non-PREEMPT_RT
32 bit systems.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/c3a1aba9-3fae-4c4b-bcb1-fb620fb7a309@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Realtek RTL8211F-VD has the same LED configuration
and registers as RTL8211F.
Use the existing LED related functions for this chip,
so it is possible to also use the netdev trigger.
Tested on ROCK Pi E.
Signed-off-by: Kryštof Černý <cleverline1mc@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260304-rtl8211fvd-add-leds-v2-1-d50bd8a50f08@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
- Remove duplicated preempt disable. Disabling preemption has been added
to functions like u64_stats_update_begin() in the meantime.
- Simplify branch structure
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/2ceeb542-986a-404e-ad0f-62e0a938ce7c@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Use macro __ATTR to simplify the code. Note that __ATTR can't be used
in MDIO_BUS_STATS_ADDR_ATTR_DECL because the included stringification
would conflict with how argument file is passed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/4877a4dc-247c-4453-b281-20a8d969b15b@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
