rockchip,rv1106-saradc was folded into the fallback enum together
with rockchip,rk3576-saradc, falling back to rockchip,rk3588-saradc.
The two IP blocks are not equivalent, though: per the RV1106 TRM v0.3,
chapter 20 (SAR-ADC), RV1106 only has 2 channels at 10-bit resolution,
versus 8 channels at 12-bit on RK3588. Documenting it as falling back
to rk3588-saradc allows device trees that would bind against the wrong
channel table and report an incorrect voltage scale.
Remove rockchip,rv1106-saradc from the RK3588 fallback enum and give
it its own standalone compatible entry, matching the dedicated match
table entry added by the driver patch.
Fixes: bdba14f612 ("dt-bindings: iio: adc: rockchip-saradc: Add RV1106 compatible")
Suggested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Vladislav Leonov <vlad@zlab.su>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Jonathan Cameron <jonathan.cameron@oss.qualcomm.com>
Group single-entries into an enum list
Suggested-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Vladislav Leonov <vlad@zlab.su>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Jonathan Cameron <jonathan.cameron@oss.qualcomm.com>
The Microchip MCP47A1 is a 6-bit volatile Digital-to-Analog converter
which communicates via I2C.
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Joshua Crofts <joshua.crofts1@gmail.com>
Signed-off-by: Jonathan Cameron <jonathan.cameron@oss.qualcomm.com>
I'm transitioning to a new email, add mapping and update MAINTAINERS
entries to keep email up to date.
Signed-off-by: Maxwell Doose <maxwell@maxwelld.cc>
Signed-off-by: Jonathan Cameron <jonathan.cameron@oss.qualcomm.com>
Document the bindings for the Sensirion SLF3S family of digital
liquid-flow sensors on I2C. The family currently covers the
SLF3S-0600F, SLF3S-1300F and SLF3S-4000B variants.
All variants share the same register map and differ only in the flow
scale factor and the calibrated measurement range, which the driver
reads back from the product-information register. Since that lookup
is needed in any case, a fallback compatible would buy nothing, so
each variant gets its own compatible without a fallback. A future
drop-in compatible part can then claim one of these compatibles and
work on kernels that do not know its product ID yet.
The active calibration medium (water / IPA) is runtime-switchable
via the in_volumeflow_medium sysfs attribute and therefore not a
DT property.
Signed-off-by: Wadim Mueller <wafgo01@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Jonathan Cameron <jonathan.cameron@oss.qualcomm.com>
Document how to describe LTC2378-20 and similar ADCs in device tree.
Reviewed-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Jonathan Cameron <jonathan.cameron@oss.qualcomm.com>
Add the ICM42607 and ICM42607P inertial measurement unit.
This device is functionally very similar to the icm42600 series with a
very different register layout. The icm42607 currently does not use an
interrupt because wake on movement and buffers are not supported, and
cannot be implemented on my test device which lacks an interrupt line.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Jonathan Cameron <jonathan.cameron@oss.qualcomm.com>
Add mount-matrix attribute to schema. This attribute has been supported
since the first revision of this driver, but was not documented.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Jonathan Cameron <jonathan.cameron@oss.qualcomm.com>
Add compatible entries for AD5313R, AD5317R, AD5674, AD5679, AD5687,
AD5687R, AD5689, AD5689R. These devices have unique combination of channel
count, bit resolution and supported command set, so that fallback
compatibles are not used. Also, a small copy-and-paste error is fixed to
the title field.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Rodrigo Alencar <rodrigo.alencar@analog.com>
Signed-off-by: Jonathan Cameron <jonathan.cameron@oss.qualcomm.com>
Add support for AD5316R, AD5675 and AD5697R. These devices have different
bit resolutions or different number of channels so no fallback compatibles
are used.
Signed-off-by: Rodrigo Alencar <rodrigo.alencar@analog.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Jonathan Cameron <jonathan.cameron@oss.qualcomm.com>
Add compatible entries for AD5673R and AD5677R. These 16-channel devices
have different bit resolutions so no fallback compatibles are used.
Signed-off-by: Rodrigo Alencar <rodrigo.alencar@analog.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Jonathan Cameron <jonathan.cameron@oss.qualcomm.com>
Add device tree bindings for the QST QMC6308, a 3-axis anisotropic
magnetoresistive (AMR) magnetometer. It is an I2C device with a single
supply and no interrupt pin, at I2C address 0x2c.
Assisted-by: Claude:claude-fable-5
Signed-off-by: Jorijn van der Graaf <jorijnvdgraaf@catcrafts.net>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Jonathan Cameron <jonathan.cameron@oss.qualcomm.com>
Change personal email to the Linux specific one,
to have a single and focused point of interaction.
Signed-off-by: Siratul Islam <siratul.islam@linux.dev>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/linux-iio/a509d034-de90-4e46-bd7e-75f61002d6ba@kernel.org/
Signed-off-by: Jonathan Cameron <jonathan.cameron@oss.qualcomm.com>
Add AD4883 compatible string to the AD4080 devicetree binding.
The AD4883 is a dual-channel, 16-bit, 40 MSPS SAR ADC, sharing the same
register map and interface as the AD4080 family. Like the AD4880, it
requires two SPI chip selects and two io-backends for its independent
ADC channels. The AD4883 differs from the AD4880 in resolution (16-bit
vs 20-bit), which requires distinct channel configuration in the driver,
precluding a fallback compatible.
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Signed-off-by: Jonathan Cameron <jonathan.cameron@oss.qualcomm.com>
Add the compatible for the SARADC of the Rockchip RV1106, which is
compatible with the RK3588 variant.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Jonathan Cameron <jonathan.cameron@oss.qualcomm.com>
Add new bindings for ti,ads112c14 and similar devices.
This is an ADC that is primarily intended for use with resistive sensors
(RTD, thermocouple, Wheatstone bridge, etc.). There are a few unusual
properties because of this. In particular, the reference voltage source
and current output requirements can be different for each measurement,
so these are included in the channel bindings.
The REFP/REFN reference voltage is usually just connected to a resistor
that is being driven by the ADC's current outputs, so there is special
property for this case rather than requiring a regulator to be defined
to represent that.
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: David Lechner (TI) <dlechner@baylibre.com>
Signed-off-by: Jonathan Cameron <jonathan.cameron@oss.qualcomm.com>
Add a generic input-chopping property to adc.yaml. This is a feature
seen frequently in ADCs that are designed to measure resistive loads,
such as RTDs and strain gauges. Enabling this can reduce offset errors
by swapping the positive and negative input channels on every other
conversion. This can have side-effects in timing and filter response, so
it is not always desirable to enable this feature in some applications.
Therefore, it is best to make this a property that can be enabled or
disabled in the device tree.
Signed-off-by: David Lechner (TI) <dlechner@baylibre.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Jonathan Cameron <jonathan.cameron@oss.qualcomm.com>
Some ADCs incorporate burn-out current sources that provide current to
the channel's input pins for open-circuit or short-circuit detection.
Signed-off-by: Kurt Borja <kuurtb@gmail.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: David Lechner (TI) <dlechner@baylibre.com>
Signed-off-by: Jonathan Cameron <jonathan.cameron@oss.qualcomm.com>
Some ADCs incorporate current sources that provide excitation current to
resistive temperature devices (RTDs), thermistors, diodes and other
resistive sensors that require constant current biasing.
Signed-off-by: Kurt Borja <kuurtb@gmail.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: David Lechner (TI) <dlechner@baylibre.com>
Signed-off-by: Jonathan Cameron <jonathan.cameron@oss.qualcomm.com>
Some ADCs have configurable voltage reference sources for each channel.
Signed-off-by: Kurt Borja <kuurtb@gmail.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: David Lechner (TI) <dlechner@baylibre.com>
Signed-off-by: Jonathan Cameron <jonathan.cameron@oss.qualcomm.com>
Fix misspelling of 'reference' (was 'referance') in the
vrefp-supply and vrefn-supply descriptions.
Signed-off-by: Yahya Toubali <yahya@yahyatoubali.me>
Signed-off-by: Jonathan Cameron <jonathan.cameron@oss.qualcomm.com>
The AD3532R/AD3532 is a 16-channel version of the AD3530R/AD3530.
This adds compatible strings for the AD3532R/AD3532.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Kim Seer Paller <kimseer.paller@analog.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
I was dropped as maintainer because emails to my previous address
were bouncing. I have not stepped down from maintainership, so
re-add me with my current email address.
Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add devicetree binding for the AMD/Xilinx Versal System Monitor (SysMon).
The Versal SysMon is the successor to the Zynq UltraScale+ AMS block,
providing on-chip voltage and temperature monitoring. The hardware
supports up to 160 supply voltage measurement points and up to 64
temperature satellites distributed across the SoC, with configurable
threshold alarms and oversampling. The device can be accessed via
memory-mapped I/O or via an I2C interface.
Supply and temperature channels are described as child nodes under
container nodes, referencing the standard adc.yaml binding for
channel properties.
Co-developed-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Salih Erim <salih.erim@amd.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The MediaTek mt6323 PMIC includes an AUXADC used for battery voltage,
temperature, and other internal measurements. The IP block is not
register-compatible with mt6359.
Add the devicetree binding documentation and the associated header file
defining the ADC channel constants.
Also change the description to 'MT6350 series and similar' because
the binding already includes more than mt635x series PMICs.
Finally, add the MAINTAINERS entry for the header with ADC constants.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Roman Vivchar <rva333@protonmail.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The TMP119 has the same register layout as the TMP117, and a better local
sensor accuracy. Add a compatible for it.
Use ti,tmp117 as a fallback compatible for ti,tmp119.
Signed-off-by: Romain Gantois <romain.gantois@bootlin.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add supplies for VDD, VLOGIC and VREF input voltage pins. The vcc-supply
property is deprecated, once it does not really exist as none of the
devices describe any power input with that name. VCC is also misleading as
it sounds like the input power supply, but it is being used as an external
voltage reference, which should be called VREF. Certain devices require
vref-supply to be available once an internal reference voltage is absent.
For correct operation vdd and vlogic supplies are required.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Rodrigo Alencar <rodrigo.alencar@analog.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add GPIO property for RESET, LDAC and GAIN pin. RESET is active-low, LDAC
is used to load DAC channels with values from input registers and GAIN
can double the voltage in output channels. The gain-gpios property is
not available to all supported parts. The adi,range-double property
indicates that GAIN pin is hardwired to high in case gain-gpios is not
set, otherwise it sets the initial value for the gain setting.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Rodrigo Alencar <rodrigo.alencar@analog.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add supplies for VDD, VLOGIC and VREF input voltage pins. The vcc-supply
property is deprecated, once it does not really exist as none of the
devices describe any power input with that name. VCC is also misleading as
it sounds like the input power supply, but it is being used as an external
voltage reference, which should be called VREF. Certain devices require
vref-supply to be available once an internal reference voltage is absent.
For correct operation vdd and vlogic supplies are required.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Rodrigo Alencar <rodrigo.alencar@analog.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add GPIO property for RESET, LDAC and GAIN pin. RESET is active-low, LDAC
is used to load DAC channels with values from input registers and GAIN
can double the voltage in output channels. The gain-gpios property is
not available to all supported parts. The adi,range-double property
indicates that GAIN pin is hardwired to high in case gain-gpios is not
set, otherwise it sets the initial value for the gain setting.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Rodrigo Alencar <rodrigo.alencar@analog.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add devicetree binding for the QST QMC5883L 3-Axis Magnetic Sensor
connected via I2C.
Used enum so that more devices could use this binding
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Siratul Islam <siratul.islam@linux.dev>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Document the optional RATE pin GPIO used to select the HX711 output
data rate.
Update the example to show the property in use.
Signed-off-by: Piyush Patle <piyushpatle228@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Document the optional VSUP supply used by the HX711 on-chip regulator.
Also document the DVDD digital supply. DVDD is a board-supplied digital
input rail (figure 1 of the datasheet shows it as a separate supply, not
merely a bypass capacitor point) that was missing from the original
binding.
Signed-off-by: Piyush Patle <piyushpatle228@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
DT-bindings for ADF41513, an ultralow noise PLL frequency synthesizer that
can be used to implement local oscillators (LOs) as high as 26.5 GHz.
Some properties are based upon an existing PLL device properties
(e.g. ADF4350).
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Rodrigo Alencar <rodrigo.alencar@analog.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Here is the big set of char, misc, iio, fpga, and other small driver
subsystems changes for 7.2-rc1.
Lots of little stuff in here, the majority being of course the IIO
driver updates, as a list they are:
- IIO driver updates and additions
- GPIB driver bugfixes and cleanups
- Android binder driver updates (rust and C version)
- counter driver updates
- MHI driver updates
- mei driver updates
- w1 driver updates
- interconnect driver updates
- Comedi driver fixes and updates
- some obsolete char drivers removed (applicom and dtlk)
- hwtracing driver updates
- other tiny driver updates
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCajk4Gg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yl89wCdG1WBLsvKHZ3zaFWd4POE8G/gS1YAnRf0GcRB
0F1/iBXSZLaRF/p9dsGq
=fg13
-----END PGP SIGNATURE-----
Merge tag 'char-misc-7.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull misc driver updates from Greg KH:
"Here is the big set of char, misc, iio, fpga, and other small driver
subsystems changes for 7.2-rc1.
Lots of little stuff in here, the majority being of course the IIO
driver updates, as a list they are:
- IIO driver updates and additions
- GPIB driver bugfixes and cleanups
- Android binder driver updates (rust and C version)
- counter driver updates
- MHI driver updates
- mei driver updates
- w1 driver updates
- interconnect driver updates
- Comedi driver fixes and updates
- some obsolete char drivers removed (applicom and dtlk)
- hwtracing driver updates
- other tiny driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-7.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (406 commits)
w1: ds2482: Use named initializers for arrays of i2c_device_data
firmware: stratix10-svc: Add support to query Arm Trusted Firmware (ATF) version
firmware: stratix10-rsu: avoid blocking reboot_image sysfs when busy
coresight: ultrasoc-smb: Fix OOB write in smb_sync_perf_buffer()
iio: adc: nxp-sar-adc: harden buffer ISR against per-channel read failure
iio: chemical: scd30: Replace manual locking with RAII locking
iio: light: tsl2591: remove unneeded tsl2591_compatible_als_persist_cycle()
iio: dac: ad5686: create bus ops struct
iio: dac: ad5686: cleanup doc header of local structs
iio: dac: ad5686: add control_sync() for single-channel devices
iio: dac: ad5686: add helpers to handle powerdown masks
iio: dac: ad5686: add of_match table to the spi driver
iio: dac: ad5686: drop enum id
iio: dac: ad5686: remove redundant register definition
iio: dac: ad5686: refactor include headers
iio: adc: ad4080: fix AD4880 chip ID
iio: light: veml3328: add support for new device
dt-bindings: iio: light: veml6030: add veml3328
fpga: microchip-spi: fix zero header_size OOB read in mpf_ops_parse_header()
fpga: dfl-afu: validate DMA mapping length in afu_dma_map_region()
...
Add compatible string for the AuxADC block found on the MT6365 PMIC,
that is compatible with the one found in MT6359.
Signed-off-by: Louis-Alexis Eyraud <louisalexis.eyraud@collabora.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patch.msgid.link/20260429-mediatek-genio-mt6365-cleanup-v1-4-6f43838be92f@collabora.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
The Vishay VEML3328 is an RGBCIR light sensor that shares similar
devicetree properties as other existing VEMLxxxx sensors in the
kernel.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Joshua Crofts <joshua.crofts1@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add DT bindings for the Analog Devices AD4691 family of multichannel
SAR ADCs (AD4691, AD4692, AD4693, AD4694).
The four variants are not compatible with each other: AD4691/AD4692 have
16 analog input channels while AD4693/AD4694 have 8, and AD4691/AD4693
top out at 500 kSPS while AD4692/AD4694 reach 1 MSPS. These differences
in channel count and maximum sample rate require distinct compatible
strings so the driver can select the correct channel configuration and
rate limits.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Radu Sabau <radu.sabau@analog.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add AD4884 compatible string to the AD4080 devicetree binding.
The AD4884 is a dual-channel, 16-bit, 40 MSPS SAR ADC, sharing the same
register map and interface as the AD4080 family. Like the AD4880, it
requires two SPI chip selects and two io-backends for its independent
ADC channels. The AD4884 differs from the AD4880 in resolution (16-bit
vs 20-bit), which requires distinct channel configuration in the driver,
precluding a fallback compatible.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The ADT7604 shares the same die as the LTC2984. It repurposes the
custom RTD sensor type (18) as a copper trace resistance sensor
and the custom thermistor type (27) as a leak detector, and
removes thermocouple, diode and direct ADC sensor types.
Add adi,adt7604 to the compatible list and introduce two new
sensor node types specific to this device:
- copper-trace@: maps to the custom RTD sensor type (18). Two
variants: sub-ohm (< 1 ohm, adi,copper-trace-sub-ohm boolean,
no custom table and excitation current) and standard (> 1 ohm,
required adi,custom-copper-trace table, optional excitation current
defaulting to the datasheet recommended value). Primary output
is resistance in ohms. For > 1 ohm copper traces with a custom table,
the chip also outputs temperature in millidegrees Celsius.
- leak-detector@: maps to the custom thermistor sensor type (27).
Takes a required adi,custom-leak-detector lookup table encoding
resistance (uOhm) against coverage data (%). Two outputs:
resistance in ohms and coverage in percent.
Separate node types are used rather than extending the existing
rtd@ and thermistor@ nodes because adi,custom-rtd is required
for sensor type 18, and several properties (adi,number-of-wires,
adi,rtd-curve, adi,rsense-share, adi,single-ended,
adi,current-rotate) have no meaning for the new sensor types, since
the configuration is hardcoded, and would need to be explicitly
forbidden or ignored in the driver.
allOf conditions are added to restrict thermocouple, diode, direct
ADC and active temperature nodes to non-ADT7604 devices, and to
restrict copper-trace and leak-detector nodes to the ADT7604
(some parts only).
Signed-off-by: Liviu Stan <liviu.stan@analog.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add Device Tree binding for the Broadcom APDS9999 ambient light
and proximity sensor. A separate binding file is used rather
than merging with avago,apds9300.yaml because the APDS9999
has an additional vcsel-supply for the VCSEL.
The APDS9999 features individual R, G, B, and IR channels with
a green channel that uses optical coating to approximate the
human eye spectral response for ALS/lux measurements. Calibrated
RGB color sensing is not yet implemented in the driver.
Signed-off-by: Jose A. Perez de Azpillaga <azpijr@gmail.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add support for the GPADC for the Allwinner A523. It differs from the
D1/T113s/R329/T507 by having two clocks.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Michal Piekos <michal.piekos@mmpsystems.pl>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add a Devicetree binding for the MEMSIC MMC5983MA 3-axis
magnetometer.
MMC5983MA is not register-compatible with the existing MEMSIC
magnetometer drivers. It has a different register map, 18-bit output
data format, and I2C/SPI transport support.
Reviewed-by: David Lechner <dlechner@baylibre.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Vladislav Kulikov <vlad.kulikov.c@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Tomasz Duszynski is no longer the maintainer of the SCD30 driver.
Replace his entry with mine.
Link: https://lore.kernel.org/linux-iio/20260507172404.80435-1-m32285159@gmail.com/
Signed-off-by: Maxwell Doose <m32285159@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Rewrite the binding description and property text so it describes the
existing HX711 hardware behavior directly instead of documenting old
driver implementation details.
Also clarify that clock-frequency controls the SCK bit-bang timing.
No functional change.
Signed-off-by: Piyush Patle <piyushpatle228@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add a new optional label property for ADC channels to help users
identify each channel when reading values from the sysfs interface.
Signed-off-by: Antony Kurniawan Soemardi <linux@smankusors.com>
Reviewed-by: Linus Walleij <linusw@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add device tree binding documentation for the Analog Devices
AD5706R 4-channel 16-bit current output digital-to-analog converter.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Alexis Czezar Torreno <alexisczezar.torreno@analog.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add support for the AD4880, a dual-channel 20-bit 40MSPS SAR ADC
with integrated fully differential amplifiers (FDA).
The AD4880 has two independent ADC channels, each with its own SPI
configuration interface. This requires:
- Two entries in reg property for primary and secondary channel
chip selects
- Two io-backends entries for the two data channels
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The mount-matrix property supplies a 3x3 matrix that is used
to transform the values from the gyroscope to get vector
values that are relative to the way the sensor has been mounted
on the device. When the property is not specified, the identity
matrix is used.
This change adds mount-matrix as an optional property to the
dt-bindings for the bmg160 gyroscope.
Signed-off-by: Vishwas Rajashekar <vishwas.dev@vrajashkr.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
YAML literal block scalars cannot use tabs for indent.
Replace tab separators (mostly between values and trailing /* ... */
comments) with single spaces.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://patch.msgid.link/2044ee0cac191c7be8b6e989fc3c99b24aa4cc5e.1777434096.git.daniel@makrotopia.org
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
