ath12k_peer_assoc_h_mlo() unconditionally sets ml->peer_id_valid and copies
ahsta->ml_peer_id (with the ATH12K_PEER_ML_ID_VALID bookkeeping bit masked
off) into the WMI_PEER_ASSOC_CMDID ML params, which causes
ath12k_wmi_send_peer_assoc_cmd() to set ATH12K_WMI_FLAG_MLO_PEER_ID_VALID.
This needs to be gated on chips where the firmware allocates the MLD peer
ID:
- WCN7850/QCC2072 firmware always picks the ID itself and does not honor
a host-supplied one, so the value would be silently ignored anyway;
- QCC2072 firmware additionally crashes during MLO disconnect when
ATH12K_WMI_FLAG_MLO_PEER_ID_VALID was set in the preceding peer assoc,
so the bit must not be sent at all.
Branch on ah->host_alloc_ml_id:
- When true (QCN9274 etc.), behavior is unchanged: peer_id_valid is set
and the raw ahsta->ml_peer_id (without the VALID bit) is sent down.
- When false (WCN7850, QCC2072), peer_id_valid stays unset and
ml_peer_id is sent as 0. The firmware ignores both fields and reports
the ID it allocated through HTT_T2H_MSG_TYPE_MLO_RX_PEER_MAP.
The early-return on ahsta->ml_peer_id == ATH12K_MLO_PEER_ID_INVALID only
applies on the host-alloc path, since on the firmware-alloc path the value
is ATH12K_MLO_PEER_ID_PENDING here, not INVALID.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00302-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.115823.3
Signed-off-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Link: https://patch.msgid.link/20260720-ath12k-fw-allocated-ml-peer-id-v2-6-630632758a80@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Different ath12k devices diverge on who allocates MLD peer id:
WCN7850/QCC2072 have the firmware allocate it and notify the host via
HTT_T2H_MSG_TYPE_MLO_RX_PEER_MAP event; While others let the host allocate
it and pass it down through WMI_PEER_ASSOC_CMDID with
ATH12K_WMI_FLAG_MLO_PEER_ID_VALID set.
Currently ath12k host allocates this ID and sends it to firmware by
default for all devices. This breaks WCN7850/QCC2072, because the host
maintained ID may be different from the firmware-allocated one.
Consequently data path may fail to find the dp peer and drop some received
packets. From user point of view, this results in bugs reported in [1] or
the 4-way handshake timeout issue.
Add host_alloc_ml_id flag to struct ath12k_hw_params (and a copy on struct
ath12k_hw for hot-path access) so subsequent patches can branch on it. Set
true for QCN9274/IPQ5332/IPQ5424, false for WCN7850/QCC2072. The flag will
be consumed by subsequent patches.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00302-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.115823.3
Link: https://bugzilla.kernel.org/show_bug.cgi?id=221039 # 1
Signed-off-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Link: https://patch.msgid.link/20260720-ath12k-fw-allocated-ml-peer-id-v2-5-630632758a80@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Firmware on chips that allocate the MLD peer ID itself (WCN7850 and
QCC2072) reports the assignment back to the host through
HTT_T2H_MSG_TYPE_MLO_RX_PEER_MAP. The message carries the chosen
MLD peer id, the MLD MAC address etc.
Add the message type, the on-the-wire struct, the field masks and a
handler that parses them out. The host-side state update (publishing the
dp peer into ath12k_dp_hw::dp_peers[], propagating the ID to
ath12k_dp_link_peer::ml_id and ath12k_sta::ml_peer_id) is added in a
follow-up patch;
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00302-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.115823.3
Signed-off-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Link: https://patch.msgid.link/20260720-ath12k-fw-allocated-ml-peer-id-v2-4-630632758a80@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Several pieces of host bookkeeping for MLD peer IDs encode the
same fact in different ways:
- ath12k_sta::ml_peer_id stores the raw ID in [0, ATH12K_MAX_MLO_PEERS);
- ath12k_dp_peer::peer_id, ath12k_dp_link_peer::ml_id and the index used
on ath12k_dp_hw::dp_peers[] always carry the ATH12K_PEER_ML_ID_VALID
bit (BIT(13)) when the ID is real;
- WMI_MLO_PEER_ASSOC_PARAMS::ml_peer_id sent down to firmware is
raw, without the bookkeeping bit.
The mismatch leaks into call sites that have to remember to OR
the bit in (ath12k_peer_create(), ath12k_mac_op_sta_state()) or
remember not to (ath12k_peer_assoc_h_mlo()).
Make ath12k_sta::ml_peer_id carry the VALID bit when valid, the same
way ath12k_dp_peer::peer_id and ath12k_dp_link_peer::ml_id do:
- ath12k_peer_ml_alloc() OR-s the bit in once on the way out;
the internal bitmap stays raw [0, ATH12K_MAX_MLO_PEERS);
- ath12k_peer_create() and ath12k_mac_op_sta_state() drop the
explicit OR;
- ath12k_peer_assoc_h_mlo() masks the bit off when populating
the WMI ml_peer_id;
While there, introduce ath12k_peer_ml_free() to mirror
ath12k_peer_ml_alloc(), which helps avoid code duplication.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00302-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.115823.3
Signed-off-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Link: https://patch.msgid.link/20260720-ath12k-fw-allocated-ml-peer-id-v2-3-630632758a80@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
ath12k_bss_assoc(), ath12k_mac_station_assoc() and
ath12k_sta_rc_update_wk() all open-code the same sequence: reinit the
peer_assoc_done completion, send the peer assoc WMI command, then wait
for the firmware confirmation event. The reinit_completion() was buried
in ath12k_peer_assoc_prepare(), far from the wait_for_completion_timeout()
that consumes it, making the reinit/send/wait sequence hard to follow,
and the three open-coded copies are easy to get out of sync.
Move the sequence into a new helper ath12k_mac_peer_assoc() and call it
from all three sites. The reinit, send and wait now live together so the
completion's lifecycle is easy to read.
While at it, ath12k_sta_rc_update_wk() previously warned but still
waited the full timeout when the peer assoc command failed to send. Now
a send failure returns immediately and skips the pointless 1 second
wait, matching the other two callers.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00302-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.115823.3
Signed-off-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Link: https://patch.msgid.link/20260720-ath12k-fw-allocated-ml-peer-id-v2-2-630632758a80@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
ath12k_mac_dp_peer_cleanup() clears the ML peer ID slot on the
free_ml_peer_id_map bitmap by indexing it with dp_peer->peer_id. That is
wrong: dp_peer->peer_id for an MLO peer always carries the
ATH12K_PEER_ML_ID_VALID bit (BIT(13)), so clear_bit() is invoked with
index >= 0x2000, which is far outside the bitmap of ATH12K_MAX_MLO_PEERS
(256) bits and corrupts memory adjacent to ah->free_ml_peer_id_map. The
intended bitmap entry also never gets cleared, so subsequent
ath12k_peer_ml_alloc() calls eventually run out of IDs.
The ID without the VALID bit is what ath12k_peer_ml_alloc() returned and
is stored in ahsta->ml_peer_id. Use that instead.
While there, also reset ahsta->ml_peer_id to ATH12K_MLO_PEER_ID_INVALID so
the bitmap and ahsta->ml_peer_id stay in sync.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00302-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.115823.3
Fixes: ee16dcf573 ("wifi: ath12k: Define ath12k_dp_peer structure & APIs for create & delete")
Signed-off-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Link: https://patch.msgid.link/20260720-ath12k-fw-allocated-ml-peer-id-v2-1-630632758a80@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The memory allocated for data->powernow_table inside
powernow_k8_cpu_init_acpi() or find_psb_table() is not freed in one of
the error paths in powernowk8_cpu_init(). Fix that by adding a kfree().
Fixes: 1ff6e97f1d ("[CPUFREQ] cpumask: avoid playing with cpus_allowed in powernow-k8.c")
Cc: stable@vger.kernel.org
Signed-off-by: Abdun Nihaal <nihaal@cse.iitm.ac.in>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Zhongqiu Han <zhongqiu.han@oss.qualcomm.com>
Link: https://patch.msgid.link/20260727093553.98246-1-nihaal@cse.iitm.ac.in
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The audio_sec_mclk_in1 and audio_sec_mclk_out1 groups both list
"gpio37", but in the pingroup table those functions are muxed on
gpio39, while gpio37 provides the audio_sec_mclk_in0/out0 variants.
This makes both functions unusable: selecting them on gpio39 is
rejected by the pinmux core because the group is not listed for the
function, and selecting them on gpio37 trips the WARN_ON() in
msm_pinmux_set_mux() and fails with -EINVAL because that group
cannot mux them.
Point both groups at gpio39, matching the pingroup table. This also
mirrors the primary audio MCLK pair, where the mclk0 and mclk1
variants live on separate pins (gpio53 and gpio51 respectively).
Fixes: 3c8e7ba0e3 ("pinctrl: qcom: Introduce IPQ9650 TLMM driver")
Assisted-by: Claude:claude-fable-5
Signed-off-by: Taceddin Sancak <ts.solidarity@gmail.com>
Acked-by: Linus Walleij <linusw@kernel.org>
Reviewed-by: Kathiravan Thirumoorthy <kathiravan.thirumoorthy@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://patch.msgid.link/20260718002146.698973-1-ts.solidarity@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
The HP Dragonfly Folio G3 2-in-1 also ships with PCI SSID 103c:8a05.
On this unit the ALC245 codec reports subsystem id 103c:8a06 - the SSID
that is already covered by commit 0a10faad5c ("ALSA: hda/realtek: add
quirk for HP Dragonfly Folio G3 2-in-1") - while the PCI SSID that
SND_PCI_QUIRK matches against is 103c:8a05:
snd_hda_codec_alc269 ehdaudio0D0: ALC245: picked fixup for PCI SSID 103c:8a05
cs35l41-hda spi1-CSC3551:00-cs35l41-hda.0: CS35L41 Bound - SSID: 103C8A06
The existing entry therefore never applies here, the four CS35L41
amplifiers on SPI are not registered and the internal speakers stay
silent.
Add the same fixup that the 8a06 entry uses: the four amplifiers bind
and the speaker mute LED (codec GPIO 0x04) works.
Signed-off-by: Michael Diesen <michael.diesen@posteo.de>
Link: https://patch.msgid.link/20260727091920.4634-1-michael.diesen@posteo.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Lenovo Legion 7 15ASH11 with AMD RYZEN AI MAX+ 392 (Strix Halo, ACP
7.0) uses Realtek ALC287 series codec. Its audio subsystem adopts a
hardware design similar to that of the Yoga Pro 7 15ASH11.
It shares PCI SSID 17aa:38f9 with Thinkbook 16P Gen5.
Therefore, use HDA_CODEC_QUIRK to apply ALC287_FIXUP_LENOVO_YOGA_PRO7
for identification.
After added the HDA_CODEC_QUIRK quirk special for Lenovo Legion 7
15ASH11, the mic mute LED works well.
Signed-off-by: Jackie Dong <xy-jackie@139.com>
Link: https://patch.msgid.link/20260727080048.13254-1-xy-jackie@139.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
MIN_PERF and MAX_PERF are optional CPPC controls. DESIRED_PERF is also
optional with CPPC2 when autonomous selection is supported.
The cppc-cpufreq target callbacks populate both limits for every request
without checking whether the controls are implemented. cppc_set_perf()
consequently passes NULL register descriptors to cpc_write(). The writes
fail width validation and their return values are ignored, so the failed
access paths are repeated on every target request. An autonomous-only
platform can take the same path for DESIRED_PERF.
Check that each performance control is supported before calling
cpc_write().
Fixes: ea3db45ae4 ("cpufreq: cppc: Update MIN_PERF/MAX_PERF in target callbacks")
Reviewed-by: Sumit Gupta <sumitg@nvidia.com>
Signed-off-by: Christian Loehle <christian.loehle@arm.com>
Reviewed-by: Lifeng Zheng <zhenglifeng1@huawei.com>
Link: https://patch.msgid.link/20260724104042.1481804-1-christian.loehle@arm.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
pch_irq_type() is registered as the irq_chip .irq_set_type callback and
takes chip->spinlock with spin_lock_irqsave(). This callback is reached
from __setup_irq() -> __irq_set_trigger() -> chip->irq_set_type() while
the caller holds desc->lock, a raw_spinlock_t, with hardirqs disabled.
That context is not sleepable, but on PREEMPT_RT a regular spinlock_t is
an rtmutex-backed sleeping lock, so acquiring it there is invalid.
This was confirmed on a PREEMPT_RT kernel with lockdep
(PROVE_RAW_LOCK_NESTING and DEBUG_ATOMIC_SLEEP). A grounded PoC mirrored
pch_irq_type()'s locking and drove it through the real genirq carrier
irq_set_irq_type() -> __irq_set_trigger() -> chip->irq_set_type(), i.e.
the same __irq_set_trigger() edge that __setup_irq() takes for a
requested IRQ. With the original spin_lock_irqsave() edge lockdep
reported an invalid wait context, immediately followed by:
BUG: sleeping function called from invalid context at kernel/locking/spinlock_rt.c:48
in_atomic(): 1, irqs_disabled(): 1, non_block: 0, pid: 95, name: insmod
hardirqs last disabled at (3784): _raw_spin_lock_irqsave+0x4f/0x60
rt_spin_lock+0x3a/0x1c0
repro_irq_set_type+0x64/0xa0 [pch_repro]
__irq_set_trigger+0x69/0x140
irq_set_irq_type+0x78/0xd0
Switching the mirrored lock to raw_spinlock_t made both splats go away.
Convert the register lock to raw_spinlock_t. The same lock also
serializes the GPIO direction/value callbacks and the suspend/resume
register save/restore, but all of those critical sections only perform
MMIO register accesses (ioread32()/iowrite32()) and
irq_set_handler_locked(); none of them contain sleepable operations.
Keeping this register lock non-sleeping is therefore appropriate for the
irqchip callbacks and does not change the GPIO-side locking contract.
This is the same class of issue and fix as recently addressed for other
GPIO controllers, e.g. commit 286533cb14 ("gpio: sch: use raw_spinlock_t
in the irq startup path") and commit 90f0109019 ("gpio: eic-sprd: use
raw_spinlock_t in the irq startup path").
Fixes: 38eb18a6f9 ("gpio-pch: Support interrupt function")
Cc: stable@vger.kernel.org
Signed-off-by: Junjie Cao <junjie.cao@intel.com>
Reviewed-by: Linus Walleij <linusw@kernel.org>
Link: https://patch.msgid.link/20260723014129.1129730-1-junjie.cao@intel.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
When pca953x_restore_context() fails, cache_only is left disabled and
the IRQ left enabled, even though register synchronization may not have
completed successfully. Restore cache_only and disable the IRQ again on
failure, matching the state set by pca953x_save_context().
Fixes: ec5bde6201 ("gpio: pca953x: Split pca953x_restore_context() and pca953x_save_context()")
Fixes: 3e38f94606 ("gpio: pca953x: fix IRQ storm on system wake up")
Cc: stable@vger.kernel.org
Reviewed-by: Linus Walleij <linusw@kernel.org>
Signed-off-by: bui duc phuc <phucduc.bui@gmail.com>
Link: https://patch.msgid.link/20260727080205.16353-1-phucduc.bui@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
If the probe function returns an error after getting the I2C adapter for
DDC, the reference to the adapter is never released. Fix it by releasing
it in the bridge .destroy() handler.
There is no need to test the ddc pointer with !IS_ERR(), as
of_get_i2c_adapter_by_node() returns NULL on error.
Fixes: 2e2bf3a558 ("drm/bridge: display-connector: add DP support")
Cc: stable@vger.kernel.org
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Link: https://patch.msgid.link/20260717184836.2017386-1-laurent.pinchart+renesas@ideasonboard.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
After successfully configuring gpio pin as output, set the
requested initial output value via the existing gpio set
wrapper, so that the pin is not left at its previous level.
Fixes: 7671f4949a ("gpio: gpio-by-pinctrl: add pinctrl based generic GPIO driver")
Signed-off-by: Alex Tran <alex.tran@oss.qualcomm.com>
Reviewed-by: Linus Walleij <linusw@kernel.org>
Link: https://patch.msgid.link/20260724-gpio-pinctrl-output-set-val-v2-1-cad55d025636@oss.qualcomm.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
The ICM USB4 switch operation request encodes two values in
request.data_len_valid: bit 4 marks the data payload valid, while bits
3:0 hold the payload length in dwords. A zero length with the valid bit
set represents the full 16-dword data array.
icm_usb4_switch_op() sets the valid bit when a transmit payload is
present. For payloads shorter than the full 16 dwords, it then assigns
the length to the whole field and clears the valid bit that was just set.
The payload is still copied into the request, but the descriptor sent to
firmware marks that data as invalid.
This affects USB4 router operations that send short payloads through the
firmware connection manager. In particular, USB4 NVM writes can send a
short final block when the image size is not aligned to the 64-byte proxy
payload size. Firmware may then ignore or reject that final block, while
full 16-dword blocks are unaffected because they are encoded as length 0
with the valid bit set.
OR the short payload length into data_len_valid so the valid bit is
preserved.
Fixes: 9039387e16 ("thunderbolt: Add USB4 router operation proxy for firmware connection manager")
Cc: stable@vger.kernel.org
Signed-off-by: Xu Rao <raoxu@uniontech.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
tb_drom_parse_entry_port() validates the device-supplied header->index
against sw->config.max_port_number before indexing sw->ports[], but the
sibling field entry->dual_link_port_nr -- a 6-bit value also read from
the DROM -- indexes the same array with no such check. A malicious or
malformed Thunderbolt device can set dual_link_port_nr beyond the
allocated sw->ports[] (max_port_number + 1 entries), producing an
out-of-bounds tb_port pointer that is stored and later dereferenced.
Reject a port entry whose dual_link_port_nr exceeds max_port_number,
the same bound already applied to header->index.
Fixes: cd22e73bdf ("thunderbolt: Read port configuration from eeprom.")
Cc: stable@vger.kernel.org
Signed-off-by: Bryam Vargas <hexlabsecurity@proton.me>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Valid bandwidth group IDs range from 1 through MAX_GROUPS, while Group
ID 0 is reserved. tb_consumed_dp_bandwidth() uses the Group ID directly
to index its local group_reserved[] array.
The array currently has MAX_GROUPS entries, so its valid indices are 0
through MAX_GROUPS - 1. Group ID MAX_GROUPS therefore accesses one
element past the end, and the final group's reserved bandwidth is not
included when the array is summed.
Give group_reserved[] MAX_GROUPS + 1 entries so direct Group ID
indexing covers the reserved ID 0 and valid IDs 1 through MAX_GROUPS.
Fixes: 52a4490e89 ("thunderbolt: Reserve released DisplayPort bandwidth for a group for 10 seconds")
Cc: stable@vger.kernel.org
Signed-off-by: Xu Rao <raoxu@uniontech.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The size passed to dma_unmap_page() must match the size used for the
corresponding dma_map_page() call.
Stream RX and TX buffers are mapped with TB_MAX_FRAME_SIZE when the
buffer pools are allocated. However, tbstream_ring_free() currently uses
tb_ring_frame_size() as the unmap size.
That helper returns the current frame payload size, not the DMA mapping
size. On the TX path, tbstream_dev_alloc_tx() stores a shorter payload
length in frame.size when the payload is smaller than TB_MAX_FRAME_SIZE.
This happens for a short final DATA frame, and also for the CLOSE frame,
which is allocated with SZ_256.
In those cases the buffer was mapped with TB_MAX_FRAME_SIZE, but
tb_ring_frame_size() returns the shorter frame payload length. This makes
the dma_unmap_page() size differ from the original dma_map_page() size.
Use TB_MAX_FRAME_SIZE when unmapping stream buffers so the unmap size
matches the DMA mapping size used by the buffer allocation paths.
Signed-off-by: Xu Rao <raoxu@uniontech.com>
Fixes: 6db21d817b ("thunderbolt: Add support for USB4STREAM")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
scpsys_get_bus_protection_legacy() looks up several legacy bus
protection regmaps from device-tree nodes.
Two error paths put the device node before checking whether the regmap
lookup failed, but still pass that node to dev_err_probe() with %pOF on
failure. If of_node_put() drops the last reference, the later %pOF
formatting can dereference a freed device node.
Keep the node reference until after the error message has been emitted in
the infracfg and SMI lookup paths. Also drop the SMI node before
returning when the SMI phandle is missing.
Fixes: c29345fa5f ("pmdomain: mediatek: Refactor bus protection regmaps retrieval")
Signed-off-by: Guangshuo Li <lgs201920130244@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
FOLL_LONGTERM pinning fails for some memory types, such as file-backed
guest memory. As a result, kvm_s390_adapter_map() returns -EINVAL and
irqfd adapter registration fails even though interrupt delivery could
still work via the existing non-atomic path.
When FOLL_LONGTERM pinning fails, verify that the page is accessible
using a short-term pin instead. If the short-term pin succeeds, unpin
the page and add a map entry with pinned=false to preserve MAP/UNMAP
symmetry. The non-atomic irqfd path already performs short-term pinning
for interrupt delivery, so this restores the previous behavior for
memory that cannot be pinned long-term.
get_map_info() is updated to return NULL for unpinned entries so that
the atomic irqfd fast path falls back to the non-atomic path.
kvm_s390_adapter_unmap() and kvm_s390_unmap_all_adapters() skip dirty
marking and unpin for unpinned entries.
Update Documentation/virt/kvm/devices/s390_flic.rst to reflect the
new MAP/UNMAP behavior.
Fixes: c9a5688380 ("KVM: s390: Add map/unmap ioctl and clean mappings post-guest")
Signed-off-by: Jaehoon Kim <jhkim@linux.ibm.com>
Reviewed-by: Douglas Freimuth <freimuth@linux.ibm.com>
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@linux.ibm.com>
fs/erofs/decompressor_lzma.c sizes the module-global MicroLZMA stream
pool from num_possible_cpus() when the lzma_streams module parameter is
unset, then z_erofs_load_lzma_config() preallocates one image-supplied
dictionary per stream, accepting dictionaries up to 8 MiB. On high-CPU
systems, a small EROFS image can pin hundreds of MiB of vmalloc-backed
decoder state until the erofs module is unloaded.
Impact: An EROFS image mounted by the system can pin up to 8 MiB of
vmalloc memory per LZMA stream, either as intended or unexpectedly.
Bound the default stream count by a new
CONFIG_EROFS_FS_ZIP_LZMA_DEFAULT_MAX_STREAMS option, default 16, so the
worst-case default preallocation is 128 MiB if the number of CPUs is no
less than 16 while preserving the existing per-image dictionary limit.
An explicit lzma_streams module parameter is still honoured as-is, so
administrators who deliberately size the pool are not affected.
Fixes: 622ceaddb7 ("erofs: lzma compression support")
Cc: stable@vger.kernel.org
Assisted-by: Claude:claude-opus-4-8
Signed-off-by: Michael Bommarito <michael.bommarito@gmail.com>
Reviewed-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Previously, backing files for page cache sharing were set up with
f_path left as NULL (only f_inode was valid). It worked, but a recent
mincore fix relies on f_path.mnt and crashes (found by "erofs/028" on
7.2-rc4):
BUG: kernel NULL pointer dereference, address: 0000000000000018
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: Oops: 0000 [#1] SMP PTI
CPU: 3 UID: 0 PID: 675528 Comm: fincore Not tainted 7.2.0-rc4-00002-g[]-dirty #1 PREEMPT(lazy)
Hardware name: Red Hat KVM, BIOS 1.16.0-4.al8 04/01/2014
RIP: 0010:__do_sys_mincore+0xc0/0x2c0
...
Specify valid paths using valid disconnected dentries together with
erofs_ishare_mnt instead of leaving f_path empty, so they are more
like real backing files in a pseudo filesystem and standard
backing_file_open() can be used directly.
Fixes: e187bc02f8 ("mm: do file ownership checks with the proper mount idmap")
Acked-by: Hongbo Li <hongbohbli@tencent.com>
Signed-off-by: Gao Xiang <xiang@kernel.org>
The cifs.idmap key type stores its payload length in key->datalen, which
is limited to U16_MAX. Accepting a larger key payload truncates the
recorded length and can make later users interpret the payload using
inconsistent bounds.
Reject oversized preparsed payloads before allocating or copying them.
This keeps key->datalen consistent with the stored data for both inline
and separately allocated idmap payloads.
Signed-off-by: Li Qiang <liqiang01@kylinos.cn>
Signed-off-by: Steve French <stfrench@microsoft.com>
Both branches of the check return the same value, so the check has
no effect. Remove it and return the value directly.
This is the result of running the Coccinelle script from
scripts/coccinelle/misc/cond_return_no_effect.cocci.
Signed-off-by: Sang-Heon Jeon <ekffu200098@gmail.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
CIFSSMBRead(), CIFSSMBWrite() and CIFSSMBWrite2() allocate a request
buffer before checking whether tcon->ses->server is NULL. If that
defensive check ever fails, the helper returns -ECONNABORTED without
releasing the request buffer.
Fix these leaks by releasing the allocated request buffer before
returning from these error paths. Use cifs_small_buf_release() for the
buffers allocated by small_smb_init() and cifs_buf_release() for the
buffer allocated by smb_init().
The bug was first flagged by an experimental analysis tool we are
developing for kernel memory-management bugs while analyzing
v6.13-rc1. The tool is still under development and is not yet publicly
available. Manual inspection confirms that the bug is still
present in v7.1.1.
An x86_64 allyesconfig build showed no new warnings.
Runtime validation used a temporary fault-injection hook to force
tcon->ses->server to NULL after request-buffer initialization. On the
unfixed kernel, the harness observed two leaked small request buffers and
one leaked large request buffer, with directed kmemleak dumps confirming
the CIFS buffer allocation stacks. After the fix, no CIFS request-buffer
deltas remained.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Dawei Feng <dawei.feng@seu.edu.cn>
Signed-off-by: Steve French <stfrench@microsoft.com>
Currently, cifs_get_swn_reg() allocates new registry entries using
GFP_ATOMIC. Since we lock a mutex here, this is clearly not an atomic
context. Use GFP_KERNEL instead.
Also, fix a minor grammatical error in the comment above the function.
Signed-off-by: Fredric Cover <fredric.cover.lkernel@gmail.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Qualcomm UFS controller found on SoCs SA8255P/SA8797P has a MCQ I/O address
space. It should be defined in the bindings even though Linux driver
currently doesn't utilize it. Fix the binding before it gets adopted by
DTS.
Fixes: e2725ed2a7 ("scsi: ufs: dt-bindings: Document bindings for SA8255P UFS Host Controller")
Cc: stable@vger.kernel.org
Signed-off-by: Shawn Guo <shengchao.guo@oss.qualcomm.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://patch.msgid.link/20260720023552.2667237-1-shengchao.guo@oss.qualcomm.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit fbefe22811 ("scsi: libsas: Don't always drain event workqueue
for HA resume") introduced sas_resume_ha_no_sync() to avoid a deadlock:
the PHYE_RESUME_TIMEOUT handler, running on the HA event workqueue,
calls sas_deform_port() -> sas_destruct_devices(), which removes SCSI
devices and waits for the host to become runtime-active. But the host
cannot resume until sas_resume_ha() -> sas_drain_work() returns, and the
drain is blocked on that very handler.
However skipping the drain reintroduces a race: hisi_sas returns from
resume before all PHY UP work and libsas discovery work finish. The
controller may then autosuspend while disks are still waking up. The
disks issue IO to a suspended controller, the IO fails, and the disks
get disabled.
Fix the deadlock at its source by moving the PHYE_RESUME_TIMEOUT
notification to after sas_drain_work(). By then the host resume is about
to complete, so device removal through device_link no longer blocks on
the resume and the cycle is broken.
With the deadlock gone, restore sas_resume_ha() (the draining variant)
in hisi_sas and remove sas_resume_ha_no_sync().
The reorder is safe for the other libsas consumers (isci, pm8001,
aic94xx, mvsas). During suspend, sas_suspend_devices() calls
sas_notify_lldd_dev_gone() for each device, which sets dev->lldd_dev to
NULL. When scsi_unblock_requests re-enables I/O in resume, any I/O to a
timed-out phy's disk is immediately rejected by the LLDD before reaching
hardware: isci returns SAS_DEVICE_UNKNOWN (mapped to DID_BAD_TARGET),
and pm8001 returns SAS_PHY_DOWN (mapped to DID_NO_CONNECT). Both
complete directly via scsi_done() without entering SCSI EH. This is
identical in both the old and new ordering since lldd_dev_gone runs
during suspend, before resume. The reorder only affects when the
PHYE_RESUME_TIMEOUT handler runs (synchronized by sas_drain_work()
vs. asynchronous after resume returns), not whether I/O can reach the
device. aic94xx and mvsas do not register any PM ops and never reach
this code path.
Fixes: fbefe22811 ("scsi: libsas: Don't always drain event workqueue for HA resume")
Signed-off-by: Xingui Yang <yangxingui@huawei.com>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Link: https://patch.msgid.link/20260716081145.3950172-1-yangxingui@huawei.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
iscsi_tcp_hdr_dissect() receives the data segment of several PDU types
into the fixed-size conn->data buffer, which is allocated for
ISCSI_DEF_MAX_RECV_SEG_LEN (8192) bytes. For the LOGIN_RSP, TEXT_RSP,
REJECT and ASYNC_EVENT opcodes the dissect path already rejects a PDU
whose DataSegmentLength exceeds that buffer.
The SCSI Command Response (ISCSI_OP_SCSI_CMD_RSP) path also copies its
data segment (sense/response data) into conn->data via
iscsi_tcp_data_recv_prep(), but it does so without the same check. The
only upstream bound on in.datalen is conn->max_recv_dlength, the
initiator's advertised MaxRecvDataSegmentLength, which is commonly
negotiated well above 8192 (open-iscsi defaults to 262144). A target
that returns a SCSI Response with a DataSegmentLength between 8193 and
max_recv_dlength therefore overflows the 8192-byte conn->data buffer.
Once the same bound applies, ISCSI_OP_SCSI_CMD_RSP is handled exactly
like those responses: bound the data segment, receive it into conn->data
when present, and otherwise complete the PDU with no data. Fold the
opcode into that case group rather than duplicating the check.
Fixes: a081c13e39 ("[SCSI] iscsi_tcp: split module into lib and lld")
Suggested-by: Chris Leech <cleech@redhat.com>
Assisted-by: Claude:claude-opus-4-8
Signed-off-by: HyeongJun An <sammiee5311@gmail.com>
Acked-by: Chris Leech <cleech@redhat.com>
Link: https://patch.msgid.link/20260716065848.1653431-1-sammiee5311@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Please consider pulling these changes from the signed vfs-7.2-rc5.fixes tag.
Thanks!
Christian
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRAhzRXHqcMeLMyaSiRxhvAZXjcogUCamYljAAKCRCRxhvAZXjc
ogWyAPwORZDIIsRiAQbnPs+OkYszuWCY29OeUrTf+m3z+tBTLwD+NUFtpH5XIcYJ
3jHtGXPoHjEaOVsNyIdxwnOxWfo+6ws=
=VNq0
-----END PGP SIGNATURE-----
Merge tag 'vfs-7.2-rc5.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs
Pull vfs fixes from Christian Brauner:
- vfs: Preserve the ACL_DONT_CACHE state in forget_cached_acl().
ACL_DONT_CACHE is meant to be a permanent opt-out from ACL caching
which FUSE relies on for servers that don't negotiate FUSE_POSIX_ACL.
The helper replaced it with ACL_NOT_CACHED, silently re-enabling the
cache, and as fuse doesn't invalidate the cache for such servers a
properly timed get_acl() returned stale ACLs. Comes with a fuse
selftest reproducing this.
- pidfs:
- Preserve PIDFD_THREAD when a thread pidfd is reopened via
open_by_handle_at(). PIDFD_THREAD shares the O_EXCL bit which
do_dentry_open() strips after the flags have been validated, so
the reopened pidfd silently became a process pidfd. Comes with a
selftest.
- Add a pidfs_dentry_open() helper so the regular pidfd allocation
path and the file handle path share the code that forces O_RDWR
and reapplies the pidfd flags that do_dentry_open() strips.
- Handle FS_IOC32_GETVERSION in the compat ioctl path.
- Make pidfs_ino_lock static.
- iomap:
- Fix the block range calculation in ifs_clear_range_dirty() so a
partial clear doesn't drop the dirty state of blocks the range
only partially covers.
- Support invalidating partial folios so a partial truncate or hole
punch with blocksize < foliosize doesn't leave stale dirty bits
behind.
- Only set did_zero when iomap_zero_iter() actually zeroed
something.
- Guard ifs_set_range_dirty() and ifs_set_range_uptodate() against
zero-length ranges where the unsigned last-block calculation
underflows and bitmap_set() writes far beyond the ifs->state
allocation.
- Don't merge ioends with different io_private values as the merge
could leak or corrupt the private data of the individual ioends.
- exec:
- Raise bprm->have_execfd only once the binfmt_misc interpreter has
actually been opened. The flag was set as soon as a matching 'O'
or 'C' entry was found. If the interpreter open failed with
ENOEXEC the exec fell through to the next binary format with
have_execfd raised but no executable staged and begin_new_exec()
NULL derefed past the point of no return.
- Fix an unsigned loop counter wrap in transfer_args_to_stack() on
nommu. An overlong argument or environment string pushes bprm->p
below PAGE_SIZE, the stop index becomes zero, and the loop never
terminates, wrapping its counter and copying garbage from in
front of the page array into the new process stack.
- Make binfmt_elf_fdpic only honour the first PT_INTERP like
binfmt_elf does. Each additional PT_INTERP overwrote the previous
interpreter, leaking the name allocation and the interpreter file
reference together with the write denial open_exec() took,
leaving the file unwritable for as long as the system runs.
- overlayfs:
- Compare the full escaped xattr prefix including the trailing dot.
An xattr like "trusted.overlay.overlayfoo" was misclassified as
an escaped overlay xattr.
- Check read access to the copy_file_range() source with the
source's mounter credentials.
- super: Thawing a filesystem whose block device was frozen with
bdev_freeze() deadlocked. Dropping the last block layer freeze
reference from under s_umount ends up in fs_bdev_thaw() which
reacquires s_umount on the same task. Pin the superblock with an
active reference instead and call bdev_thaw() without holding
s_umount.
- procfs: Return EACCES instead of success when the ptrace access check
for namespace links fails.
- afs: Use afs_dir_get_block() rather than afs_dir_find_block() for
block 0 in afs_edit_dir_remove(), matching afs_edit_dir_add().
- Push the memcg gating of ->nr_cached_objects() down into the btrfs
and shmem callbacks instead of skipping every callback during
non-root memcg reclaim. The blanket check short-circuited XFS whose
inode reclaim hook is intentionally driven from per-memcg contexts to
free memcg-charged slab.
- eventpoll: Pin files while checking reverse paths.
Since struct file became SLAB_TYPESAFE_BY_RCU a concurrent close
could free and recycle the file under the check which then took and
dropped the f_lock of whatever live file now occupies that slot.
* tag 'vfs-7.2-rc5.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs: (24 commits)
super: fix emergency thaw deadlock on frozen block devices
pidfs: make pidfs_ino_lock static
eventpoll: pin files while checking reverse paths
fs: push nr_cached_objects memcg gating into individual filesystems
afs: Fix afs_edit_dir_remove() to get, not find, block 0
iomap: prevent ioend merge when io_private differs
iomap: add comments for ifs_clear/set_range_dirty()
iomap: fix out-of-bounds bitmap_set() with zero-length range
iomap: fix incorrect did_zero setting in iomap_zero_iter()
iomap: support invalidating partial folios
iomap: correct the range of a partial dirty clear
fs/super: fix emergency thaw double-unlock of s_umount
pidfs: handle FS_IOC32_GETVERSION in compat ioctl
ovl: check access to copy_file_range source with src mounter creds
proc: Fix broken error paths for namespace links
pidfs: add pidfs_dentry_open() helper
selftests/pidfd: check PIDFD_THREAD survives open_by_handle_at()
pidfs: preserve thread pidfds reopened by file handle
ovl: fix trusted xattr escape prefix matching
selftests/fuse: add ACL_DONT_CACHE regression test
...
iscsi_scsi_cmd_rsp() copies the sense data of a SCSI Response from the
target-supplied data segment. The segment carries a 2-byte sense length
followed by the sense bytes, so it must hold 2 + senselen bytes, but the
bounds check only requires datalen >= senselen:
senselen = get_unaligned_be16(data);
if (datalen < senselen)
goto invalid_datalen;
memcpy(sc->sense_buffer, data + 2,
min_t(uint16_t, senselen, SCSI_SENSE_BUFFERSIZE));
A target that returns a SCSI Response whose datalen equals senselen
(with senselen <= SCSI_SENSE_BUFFERSIZE) makes the memcpy() from data +
2 read up to two bytes past the received data. Those bytes are stale
conn->data contents and end up in the command's sense buffer, which is
returned to userspace.
Account for the 2-byte sense length prefix in the check.
Fixes: 7996a778ff ("[SCSI] iscsi: add libiscsi")
Suggested-by: Sashiko AI <sashiko-bot@kernel.org>
Assisted-by: Claude:claude-opus-4-8
Signed-off-by: HyeongJun An <sammiee5311@gmail.com>
Acked-by: Chris Leech <cleech@redhat.com>
Link: https://patch.msgid.link/20260714104934.1404423-1-sammiee5311@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Just a couple of small bits for the SpacemiT driver - one small fix, and
a new compatible in the DT binding.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmpmL3sACgkQJNaLcl1U
h9CDnwgAggPOeUHMrQWYES7f74oTVl/kt0B1TBV6g91r8a4p0yyy7Kn6C1njBQ7n
N5bgSL2EkpQRjj2d5akh42Apwb5EQZMdqICo68XElWnk0AxH6Y1PdRkfcruU9PnS
t7KJEeBxdsZAJhx5ZEWZrIwjY/rbEvI+rfePgdm8kVeUUVs4ur6Zg1DNk/LgolOP
xr60E5DWHIczjJ3Ae+svL5mmJ8FICFOThAYjMzGyRACB4c3znMBhzKVoNrUR6sl5
7qSf1x3WBXIYwd0RRs9YhTF6vQhlnfKfu8rPfb2S6v8rE7JmmokLr3kVFzgpph1K
o893VMecWe5al0ZuE2qdf44w2Ohv0Q==
=2PTr
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v7.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"Just a couple of small bits for the SpacemiT driver - one small fix,
and a new compatible in the DT binding"
* tag 'spi-fix-v7.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: dt-bindings: spacemit: add K3 SPI compatible
spi: spacemit: Correct TX FIFO slot calculation
One driver specific fix where one of the MediaTek drivers duplicated
some core code buggily, and a core fix for an ordering issue on startup
where we could end up configuring a voltage outside of constraints due
to the order in which we applied constraints.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmpmMC4ACgkQJNaLcl1U
h9DoiAf/V64CUAFspev+AtzWpx1Su9zZoSzoMM5Gj0WBuMoo4G5hZj804DQ/n8al
sai+f0loMEVcblfpZNOlYagSkDgvvIc/1SQrAQ1oIxMbpotE1vn4htzGsJJuwwgL
lh5GC4CsrXOSRX3VG6pJeBR6RTb9VEbkAhLoxKAJyPlcynk2KdBPwR9B1ZlCgpe6
MP2WrurEVexvuDlZdE8THYth4FXCms0uH5VLo+Q3G4r1Ayt9YpvbvG91fzJSJGti
NAzAWma2GFGwQkka5sgMYHyP6rwM1vJ71mz+Bq9G5fUe6DyEp85jv993D5lq2vbH
69GO6ZTZmruCqOkDEELIKA4EpKYzZA==
=3XbV
-----END PGP SIGNATURE-----
Merge tag 'regulator-fix-v7.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"One driver specific fix where one of the MediaTek drivers duplicated
some core code buggily, and a core fix for an ordering issue on
startup where we could end up configuring a voltage outside of
constraints due to the order in which we applied constraints"
* tag 'regulator-fix-v7.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: core: clamp voltage constraints before applying apply_uV
regulator: mt6358: use regmap helper to read fixed LDO calibration
Here are a number of small char/misc/etc. driver fixes for 7.2-rc5 that
resolve a bunch of different reported issues. Included in here are:
- rust_binder error message reporting fix
- stratix10-svc firmware driver fixes
- mei driver fix
- intel_th hardware tracing driver fix
- comedi driver fix
- uio_hv_generic driver fix
- ntsync selftest fix
- nsm misc driver fix
- some MAINTAINER file updates
All of these have been in linux-next for over a week with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCamYCHg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymTpwCgyyS6niRHf2Y0qx/o+i8s87h+ipoAoJeaOzb7
RWX/ZYiUEoQCtfbxmXZF
=cRG6
-----END PGP SIGNATURE-----
Merge tag 'char-misc-7.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are a number of small char/misc/etc driver fixes for 7.2-rc5 that
resolve a bunch of different reported issues. Included in here are:
- rust_binder error message reporting fix
- stratix10-svc firmware driver fixes
- mei driver fix
- intel_th hardware tracing driver fix
- comedi driver fix
- uio_hv_generic driver fix
- ntsync selftest fix
- nsm misc driver fix
- some MAINTAINER file updates
All of these have been in linux-next for over a week with no reported
issues"
* tag 'char-misc-7.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
MAINTAINERS: Update wine-devel list address
rust_binder: only print failure if error has source
intel_th: fix MSC output device reference leak
misc: nsm: pin the module while the device is open
mei: bus: access mei_device under device_lock on cleanup
misc: nsm: only unlock nsm_dev on post-lock error paths
selftests: ntsync: correct CONFIG_NTSYNC name
comedi: comedi_parport: deal with premature interrupt
uio_hv_generic: Bind to FCopy device by default
MAINTAINERS: Add Greg Kroah-Hartman to GPIB
firmware: stratix10-svc: fix teardown order in remove to prevent race
firmware: stratix10-svc: handle NO_RESPONSE in async poll
firmware: stratix10-svc: fix FCS SMC call kernel-doc
firmware: stratix10-svc: fix memory leaks and list corruption bugs
Here are two small staging driver fixes for 7.2-rc5. They both resolve
some reported bugs in the rtl8723bs staging driver and have been in
linux-next for over a week with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCamYAxA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylfoQCghy7Exq7vpWMlhR8LwQucWqABsxsAnjzK86WN
8VZ68CMngObWMPH31Dx7
=sWD7
-----END PGP SIGNATURE-----
Merge tag 'staging-7.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are two small staging driver fixes for 7.2-rc5. They both resolve
some reported bugs in the rtl8723bs staging driver and have been in
linux-next for over a week with no reported issues"
* tag 'staging-7.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: rtl8723bs: fix OOB reads in rtw_get_wps_ie()
staging: rtl8723bs: fix inverted HT40 secondary channel offset
Here are two small serial driver fixes for 7.2-rc5. They are:
- sc16is7xx get_direction() callback fix, which resolves a
user-triggerable warning in the driver
- NULL pointer dereference on some platforms using the 8250_mid serial
driver
Both have been in linux-next for over a week with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCamYBZA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykMjACgpSS04QGbBIWmMHnxBWHnDT+Z8qoAn210DRbo
l5E84oG0BSJg1i9c3mnj
=WB87
-----END PGP SIGNATURE-----
Merge tag 'tty-7.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull serial driver fixes from Greg KH:
"Here are two small serial driver fixes for 7.2-rc5. They are:
- sc16is7xx get_direction() callback fix, which resolves a
user-triggerable warning in the driver
- NULL pointer dereference on some platforms using the 8250_mid
serial driver
Both have been in linux-next for over a week with no reported issues"
* tag 'tty-7.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: sc16is7xx: implement gpio get_direction() callback
serial: 8250_mid: Fix NULL function pointer dereference on DNV/ICX-D/SNR platforms
Here are some small USB fixes and new device quirks and ids for 7.2-rc5.
Included in here are:
- usb storage quirk added
- new usb serial device ids added
- usb-serial device name leak and other bug fixes
- small xhci driver fixes
- normal batch of typec driver fixes for reported issues
- usb-atm much-reported-by-syzbot fix for firmware download races
- sysfs BOS device removal race fix
- lots of usb gadget driver fixes for reported issues
- other small USB driver fixes for other reported problems.
All of these have been in linux-next this past week, many of them much
longer.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCamYE0A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yk0twCdFi0ivPtWtEzmP7lUNRCzmyT3MvoAoI7o6lJm
E5+ID/c4mWfX/DjoPFhU
=uUBv
-----END PGP SIGNATURE-----
Merge tag 'usb-7.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB fixes and new device quirks and ids:
- usb storage quirk added
- new usb serial device ids added
- usb-serial device name leak and other bug fixes
- small xhci driver fixes
- normal batch of typec driver fixes for reported issues
- usb-atm much-reported-by-syzbot fix for firmware download races
- sysfs BOS device removal race fix
- lots of usb gadget driver fixes for reported issues
- other small USB driver fixes for other reported problems
All of these have been in linux-next this past week, many of them much
longer"
* tag 'usb-7.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (30 commits)
usb: typec: ucsi: Correct teardown ordering in ucsi_init() error path
USB: serial: io_edgeport: cap received transmit credits
USB: serial: option: add TDTECH MT5710-CN
USB: serial: io_ti: reject oversized boot-mode firmware
USB: serial: mxuport: validate firmware header size
usb: atm: ueagle-atm: reject descriptors that confuse probe and disconnect
usb: typec: ucsi: yoga_c630: Remove redundant duplicate altmode handling
usb: typec: ucsi: Add duplicate detection to nvidia registration path
usb: typec: ucsi: Detect and skip duplicate altmodes from buggy firmware
usb: gadget: dummy_hcd: prevent fifo_req reuse during giveback
usb: chipidea: fix usage_count leak when autosuspend_delay is negative
usb: core: sysfs: add lock to bos_descriptors_read()
usb: musb: omap2430: Do not put borrowed of_node in probe
usb: core: port: Deattach Type-C connector on component unbind
USB: storage: add NO_ATA_1X quirk for Longmai USB Key
USB: serial: ftdi_sio: add support for E+H FXA291
USB: serial: keyspan_pda: fix data loss on receive throttling
usb: gadget: printer: fix infinite loop in printer_read()
usb: gadget: f_midi: cancel pending IN work before freeing the midi object
usb: gadget: udc: bdc: free IRQ and drain func_wake_notify before teardown
...
iopf_group_alloc() links each last-page IOPF group into the generic IOPF
pending list before invoking the domain fault handler.
iommufd_fault_iopf_handler() also queued an accepted group in the
IOMMUFD deliver list without removing it from the generic pending list.
When detach or HWPT replacement drops the device's IOPF reference count
to zero, an IOMMU driver may call iopf_queue_remove_device(). That
function responds to and frees groups through the generic pending list
without removing the same groups from IOMMUFD's deliver list or response
xarray. A later read, response, or cleanup can then access the freed
group and cause a UAF.
Fix this by dequeuing an accepted group from the generic pending list
before IOMMUFD queues it for userspace response.
Make iopf_group_response() send a response regardless of pending-list
membership, so the dequeued group can still be completed by IOMMUFD.
Link: https://patch.msgid.link/r/3CFD314D0FE4D7EC+20260720085017.3998878-2-peiyang_he@smail.nju.edu.cn
Closes: https://lore.kernel.org/all/B4F28798E2E784CA+d29f723c-b2b5-4b67-8d1c-4f7b9b0b27cb@smail.nju.edu.cn/
Fixes: 34765cbc67 ("iommufd: Associate fault object with iommufd_hw_pgtable")
Cc: stable@vger.kernel.org
Tested-by: Peiyang He <peiyang_he@smail.nju.edu.cn>
Assisted-by: Codex:gpt-5.6-sol
Signed-off-by: Peiyang He <peiyang_he@smail.nju.edu.cn>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
- Move rb_desc->nr_page_va before updating dynamic array
The rb_descr->page_va is a dynamic array counted by nr_page_va. But the
updating of the page_va[] is done before the nr_page_va is incremented
causing a build with CONFIG_UBSAN_BOUNDS to flag it as an overflow.
Move the increment of the counted by value before the array element is
updated.
- Propagate errors from remote event bulk updates
The return value of trace_remote_enable_event() was not being checked by
remote_events_dir_enable_write() where it would silently fail. Have it
check the return value and propagate that back up to user space.
- Fix resource leak on mmiotrace trace_pipe close
The mmiotrace tracer was created in 2008 before the trace_pipe had a close
callback to allow tracers to do clean up from trace_pipe open. The
trace_pipe close cleanup callback was added in 2009 but the mmiotrace
tracer was not updated. It had a hack to do the cleanup in the read call,
where it may leak if user space did not read the entire buffer.
Add a callback to mmiotrace trace_pipe close do to the cleanup properly.
- Fix a possible NULL pointer dereference in the mmiotrace tracer
If the mmio_pipe_open() fails to find a PCI device, it will set the
hiter->dev pointer to NULL. The read function will blindly dereference
that pointer. Fix the read call to check to see if that pointer is
populated before dereferencing it.
- Fix union collision of module and refcnt for dynamic events
In 'struct trace_event_call', the 'module' pointer and the 'refcnt' atomic
variable share the same memory space in a union. The filter on module
logic only checked if the 'module' was set to determine if the event
belonged to the module. As dynamic events are always builtin, it doesn't
need the 'module' field of the structure and used a refcount. But the
module filtering logic would then mistaken these dynamic events as a
module and call module_name(event->module) on it.
Add a check to see if the event is a dynamic event and if so, do not check
it for being part of the given module.
- Reset the top level buffer in selftests before running instances
The ftracetest selftest initializes each instance before executing the
tests. But it does not reset the top level buffer. Dynamic events are only
added and removed by the top level so any left over dynamic events will
not be removed by the reset in the instances.
Left over dynamic events can cause the tests to incorrectly fail. Reset
the top level buffer before running the instances.
- Make the context_switch counter 64 bit
The code to read user space for a system call trace event or for a
trace_marker will disable migration, enable preemption, read user space
into a per CPU buffer, disable preemption and enable migration again.
It checks if the per CPU context switch counter to see if it changed, and
if it did not, it would know that the per CPU buffer was not touched by
another task.
But the save counter was 32 bit and it would compare it to the 64 bit
context_switch variable. A long running system could have the
context_switch variable greater that 1<<32 in which case the compare will
always fail. The compare will promote the 32 bit int saved value to 64 bit
and compare it to the full 64 bit counter. Since the top 32 bits of the
saved value was zero, it would never match.
- Fix a use-after-free of the event_enable trigger
The event_enable trigger allows for enabling one event when another event
is triggered. When the trigger is removed, it must go through a
synchronization phase to make sure it is not triggered again. The trigger
itself is delayed by the "bulk delay" logic that was recently added.
But the code that frees the event_enable data used to rely on the trigger
code to do the synchronization. Now that the code uses the call RCU
functions (and a workqueue), that delay no longer is there.
Add a callback private_data_free() function that allows triggers to clean
up data after the synchronization phase has completed.
- Move the module_ref counter into the delay callback
Since an event of the event_enable trigger can enable an event for a
module, it ups the module ref count for that event's module. This prevents
the event from trying to enable an event that no longer exists and cause a
use-after-free bug.
The ref counter was set back down when the trigger was removed but not
after thy synchronization phase. This could lead to the module data being
accessed after module was unloaded.
Move the module ref decrement into the private_data_free() callback of the
event_enable trigger.
- Add mutex to protect parser in ftrace filtering
The set_ftrace_filter file uses a parsing descriptor that is allocated at
open and modified by writes. If multiple threads were to write to the
descriptor at the same time, it can corrupt the parser.
Add a mutex around the modifications of the parser descriptor.
- Fix possible corruption in perf syscall tracing
The perf system call trace events can now read user space. To do so, the
reads of user space enable preemption and disables it again. During this
time that preemption is enabled, the task can migrate. The perf event list
head is assigned via a per CPU pointer. It is done before the user space
part is called. If the user space reading migrates the task to another
CPU, then the head pointer is no longer valid.
Re-assign the head pointer after the reading of user space to keep it
using the correct data.
-----BEGIN PGP SIGNATURE-----
iIoEABYKADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCamYDGhQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qkhYAP9G5wDTVQQzitl900iWp9rvQ2Qm5UWN
JDnK2HO1elmj0AD8CRiHBI5W3O2yUmoO4bOFZ9YFXz+DqJ1jwkDs5FfqjAU=
=EMD9
-----END PGP SIGNATURE-----
Merge tag 'trace-v7.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull tracing fixes from Steven Rostedt:
- Move rb_desc->nr_page_va before updating dynamic array
The rb_descr->page_va is a dynamic array counted by nr_page_va. But
the updating of the page_va[] is done before the nr_page_va is
incremented causing a build with CONFIG_UBSAN_BOUNDS to flag it as an
overflow.
Move the increment of the counted by value before the array element
is updated.
- Propagate errors from remote event bulk updates
The return value of trace_remote_enable_event() was not being checked
by remote_events_dir_enable_write() where it would silently fail.
Have it check the return value and propagate that back up to user
space.
- Fix resource leak on mmiotrace trace_pipe close
The mmiotrace tracer was created in 2008 before the trace_pipe had a
close callback to allow tracers to do clean up from trace_pipe open.
The trace_pipe close cleanup callback was added in 2009 but the
mmiotrace tracer was not updated. It had a hack to do the cleanup in
the read call, where it may leak if user space did not read the
entire buffer.
Add a callback to mmiotrace trace_pipe close do to the cleanup
properly.
- Fix a possible NULL pointer dereference in the mmiotrace tracer
If the mmio_pipe_open() fails to find a PCI device, it will set the
hiter->dev pointer to NULL. The read function will blindly
dereference that pointer. Fix the read call to check to see if that
pointer is populated before dereferencing it.
- Fix union collision of module and refcnt for dynamic events
In 'struct trace_event_call', the 'module' pointer and the 'refcnt'
atomic variable share the same memory space in a union. The filter on
module logic only checked if the 'module' was set to determine if the
event belonged to the module. As dynamic events are always builtin,
it doesn't need the 'module' field of the structure and used a
refcount. But the module filtering logic would then mistaken these
dynamic events as a module and call module_name(event->module) on it.
Add a check to see if the event is a dynamic event and if so, do not
check it for being part of the given module.
- Reset the top level buffer in selftests before running instances
The ftracetest selftest initializes each instance before executing
the tests. But it does not reset the top level buffer. Dynamic events
are only added and removed by the top level so any left over dynamic
events will not be removed by the reset in the instances.
Left over dynamic events can cause the tests to incorrectly fail.
Reset the top level buffer before running the instances.
- Make the context_switch counter 64 bit
The code to read user space for a system call trace event or for a
trace_marker will disable migration, enable preemption, read user
space into a per CPU buffer, disable preemption and enable migration
again. It checks if the per CPU context switch counter to see if it
changed, and if it did not, it would know that the per CPU buffer was
not touched by another task.
But the save counter was 32 bit and it would compare it to the 64 bit
context_switch variable. A long running system could have the
context_switch variable greater that 1<<32 in which case the compare
will always fail. The compare will promote the 32 bit int saved value
to 64 bit and compare it to the full 64 bit counter. Since the top 32
bits of the saved value was zero, it would never match.
- Fix a use-after-free of the event_enable trigger
The event_enable trigger allows for enabling one event when another
event is triggered. When the trigger is removed, it must go through a
synchronization phase to make sure it is not triggered again. The
trigger itself is delayed by the "bulk delay" logic that was recently
added. But the code that frees the event_enable data used to rely on
the trigger code to do the synchronization. Now that the code uses
the call RCU functions (and a workqueue), that delay no longer is
there.
Add a callback private_data_free() function that allows triggers to
clean up data after the synchronization phase has completed.
- Move the module_ref counter into the delay callback
Since an event of the event_enable trigger can enable an event for a
module, it ups the module ref count for that event's module. This
prevents the event from trying to enable an event that no longer
exists and cause a use-after-free bug.
The ref counter was set back down when the trigger was removed but
not after thy synchronization phase. This could lead to the module
data being accessed after module was unloaded.
Move the module ref decrement into the private_data_free() callback
of the event_enable trigger.
- Add mutex to protect parser in ftrace filtering
The set_ftrace_filter file uses a parsing descriptor that is
allocated at open and modified by writes. If multiple threads were to
write to the descriptor at the same time, it can corrupt the parser.
Add a mutex around the modifications of the parser descriptor.
- Fix possible corruption in perf syscall tracing
The perf system call trace events can now read user space. To do so,
the reads of user space enable preemption and disables it again.
During this time that preemption is enabled, the task can migrate.
The perf event list head is assigned via a per CPU pointer. It is
done before the user space part is called. If the user space reading
migrates the task to another CPU, then the head pointer is no longer
valid.
Re-assign the head pointer after the reading of user space to keep it
using the correct data.
* tag 'trace-v7.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracing: perf: Fix stale head for perf syscall tracing
ftrace: Add global mutex to serialize trace_parser access
tracing: Delay module ref count for "enable_event" trigger
tracing: Fix use-after-free freeing trigger private data
tracing: Fix context switch counter truncation
selftests/ftrace: Reset triggers at top level before instance loop
tracing: Fix union collision of module and refcnt for dynamic events
tracing: Fix mmiotrace possible NULL dereferencing of hiter->dev
tracing: Fix resource leak on mmiotrace trace_pipe close
tracing: Propagate errors from remote event bulk updates
tracing/remotes: Fix page_va[] access before counter update in trace_remote_alloc_buffer()
a bit more widely, because newer versions of LLVM started
optimizing it a bit better and introduced run-time relocations
in PIE code. (Nathan Chancellor)
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=3e+9
-----END PGP SIGNATURE-----
Merge tag 'x86-urgent-2026-07-26' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fix from Ingo Molnar:
- Disable jump/lookup tables in the x86 boot decompressor code
a bit more widely, because newer versions of LLVM started
optimizing it a bit better and introduced run-time relocations
in PIE code (Nathan Chancellor)
* tag 'x86-urgent-2026-07-26' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/boot/compressed: Disable jump tables
do_thaw_all_callback() calls bdev_thaw() while holding sb->s_umount
exclusively. If the block device was frozen via bdev_freeze() dropping
the last block layer freeze reference calls fs_bdev_thaw() which
reacquires s_umount:
do_thaw_all_callback(sb)
super_lock_excl(sb) # holds sb->s_umount
bdev_thaw(sb->s_bdev)
mutex_lock(&bdev->bd_fsfreeze_mutex)
# bd_fsfreeze_count drops 1 -> 0
bd_holder_ops->thaw == fs_bdev_thaw
get_bdev_super(bdev)
bdev_super_lock(bdev, true)
super_lock(sb, true)
down_write(&sb->s_umount) # same task: deadlock
The emergency thaw worker deadlocks against itself holding both
s_umount and bd_fsfreeze_mutex. That fscks any subsequent unmount,
freeze, or thaw of that filesystem and block device.
[ 81.878470] sysrq: Show Blocked State
[ 81.880140] task:kworker/0:1 state:D stack:0 pid:11 tgid:11 ppid:2 task_flags:0x4208060 flags:0x00080000
[ 81.884876] Workqueue: events do_thaw_all
[ 81.886656] Call Trace:
[ 81.887759] <TASK>
[ 81.888763] __schedule+0x579/0x1420
[ 81.890372] schedule+0x3a/0x100
[ 81.891794] schedule_preempt_disabled+0x15/0x30
[ 81.893848] rwsem_down_write_slowpath+0x1ea/0x900
[ 81.895191] ? __pfx_do_thaw_all_callback+0x10/0x10
[ 81.896528] down_write+0xbd/0xc0
[ 81.897505] super_lock+0x91/0x180
[ 81.898457] ? __mutex_lock+0xa99/0x1140
[ 81.900748] ? __mutex_unlock_slowpath+0x1f/0x400
[ 81.902069] bdev_super_lock+0x5b/0x150
[ 81.903132] get_bdev_super+0x10/0x60
[ 81.904042] fs_bdev_thaw+0x23/0xf0
[ 81.904755] bdev_thaw+0x82/0x100
[ 81.905484] do_thaw_all_callback+0x2c/0x50
[ 81.906298] __iterate_supers+0x5d/0x130
[ 81.907067] do_thaw_all+0x20/0x40
[ 81.907739] process_one_work+0x206/0x5e0
[ 81.908545] worker_thread+0x1e2/0x3c0
[ 81.909339] ? __pfx_worker_thread+0x10/0x10
[ 81.910171] kthread+0xf4/0x130
[ 81.910799] ? __pfx_kthread+0x10/0x10
[ 81.911528] ret_from_fork+0x2e2/0x3b0
[ 81.912259] ? __pfx_kthread+0x10/0x10
[ 81.913010] ret_from_fork_asm+0x1a/0x30
[ 81.913806] </TASK>
bdev_super_lock() even documents the violated requirement with
lockdep_assert_not_held(&sb->s_umount).
Acquiring bd_fsfreeze_mutex under s_umount also inverts the
bd_fsfreeze_mutex vs. s_umount ordering established by
bdev_{freeze,thaw}() and can thus ABBA against a concurrent block-layer
freeze even when the recursive path isn't hit.
Fix this by not holding s_umount around the bdev_thaw() loop at all. Pin
the superblock with an active reference instead as
filesystems_freeze_callback() does. The active reference keeps the
superblock from being shut down and so ->s_bdev stays valid without
holding s_umount. The block-layer-held freeze is dropped by
fs_bdev_thaw() with FREEZE_MAY_NEST | FREEZE_HOLDER_USERSPACE exactly as
a regular unfreeze would and thaw_super_locked() handles
filesystem-level freezes as before.
The emergency thaw path has deadlocked like this in one form or
another for a long long time but the current exclusively-held
shape dates back to commit [1] where thaw_bdev() already ended in
thaw_super() with s_umount held by do_thaw_all_callback().
Fixes: 08fdc8a013 ("buffer.c: call thaw_super during emergency thaw") [1]
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20260723-work-super-emergency_thaw-v1-1-7c315c600245@kernel.org
Signed-off-by: Christian Brauner (Amutable) <brauner@kernel.org>
An attacker injecting interrupts while the Safe-RET mitigation executes
on machines affected by SRSO can neutralize the safe return sequence,
potentially leading to data leakage through speculative execution.
Fixup register state as if the Safe-RET sequence executed successfully
by "emulating" it, in a manner of speaking, and avoid executing a RET
instruction after returning from the interrupt.
Co-developed-by: David Kaplan <David.Kaplan@amd.com>
Signed-off-by: David Kaplan <David.Kaplan@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
snd_timer_close_locked() marks an instance with SNDRV_TIMER_IFLG_DEAD
and returns early when the flag is already set, but the flag is never
cleared again. A completed close ends in remove_slave_links(), which
leaves timeri->timer NULL, so a second close is already harmless through
the timer == NULL path; the early return can only be reached by an
instance that was opened again in between. For such an instance the
close unlinks nothing, so snd_timer_instance_free() frees an object that
is still on timer->open_list_head, still on snd_timer_master_list if it
was opened with a slave key, still owns any adopted slaves, and still
holds its timer and module references.
snd_seq_timer_open() reopens an instance exactly like that: it retries
its fallback open on the same object after a failure that has already
run snd_timer_close_locked() internally. An unprivileged user with
access to /dev/snd/timer and /dev/snd/seq can force that failure, since
snd_timer_check_master() returns -EBUSY when a pending slave matches the
new master's (slave_class, slave_id) key and the target timer has
reached max_instances, and SNDRV_TIMER_IOCTL_SELECT with dev_class =
SNDRV_TIMER_CLASS_SLAVE keeps the caller-supplied dev_sclass, so a
sequencer queue's key can be forged. The freed instance is afterwards
dereferenced by any further snd_timer_open() on that timer, by
snd_timer_check_slave(), and by /proc/asound/timers, which faults on the
stale ti->owner pointer.
The flag only has to be visible while the close is in progress, which is
all its other users need. Clear it in remove_slave_links(), under the
same timer->lock that sets it, once the instance is off every list.
Fixes: da3039e91d ("ALSA: timer: Forcibly close timer instances at closing")
Cc: stable@vger.kernel.org
Assisted-by: Claude:claude-opus-5
Signed-off-by: Norbert Szetei <norbert@doyensec.com>
Link: https://patch.msgid.link/CA41AA48-75BF-45E9-A36D-3A5D2F124F60@doyensec.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Infinix INBOOK X3 Slim (ALC269VB, subsystem 0x2782:0250) has its
internal speakers wired to pin 0x1b, but the BIOS pin configuration
table declares 0x1b as "no physical connection" (0x411111f0). It instead
declares pin 0x14 as the internal speaker, although nothing is connected
to 0x14.
As a result the internal speakers are silent under Linux while the
headphone jack works correctly. The codec output path to 0x14 is fully
open (DAC assigned and streaming, mixer and pin unmuted, EAPD asserted),
so the failure is silent with no error reported. The speakers work under
Windows, where the vendor driver supplies its own pin table.
Add a fixup that disables the unconnected pin 0x14 and declares pin
0x1b as the internal speaker.
Reusing the existing ALC269VC_FIXUP_INFINIX_Y4_MAX was tried first, since
it also remaps 0x1b to an internal speaker. It is not sufficient here: it
leaves 0x14 declared, so autoconfig finds two line_outs
line_outs=2 (0x14/0x1b/0x0/0x0/0x0) type:speaker
and binds the primary "Speaker" control to the unconnected pin 0x14 while
demoting the working speaker at 0x1b to "Bass Speaker". Audio is audible
that way, but the volume and mute controls a desktop actually uses end up
attached to a pin that is not wired to anything. Disabling 0x14 is what
produces a single correct Speaker output.
Verified on the affected machine: with the corrected pin
configuration the driver's autoconfig reports
line_outs=1 (0x1b/0x0/0x0/0x0/0x0) type:speaker
both channels play, headphone auto-mute switches correctly in both
directions, and audio survives codec runtime suspend (D3) and resume.
Signed-off-by: Gunal Seenivasagan <gunal2002@gmail.com>
Link: https://patch.msgid.link/20260726085715.229802-1-gunal2002@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Although 6fire driver had a few fixes for dealing with the early error
handling during the probe phase, it forgot a pending URB before
freeing the resources, which may lead to a UAF.
This patch addresses it by doing the almost same cleanup procedure
like the normal disconnect phase at the error path.
Reported-and-tested-by: Shuangpeng Bai <shuangpeng.kernel@gmail.com>
Closes: https://lore.kernel.org/20260724030900.1984491-1-shuangpeng.kernel@gmail.com
Cc: <stable@vger.kernel.org>
Link: https://patch.msgid.link/20260726074821.2288158-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_usbmidi_akai_output() computes its fill-loop bound
buf_end = ep->max_transfer - MAX_AKAI_SYSEX_LEN - 1;
as a signed int, so a small device-advertised bulk-OUT max_transfer
makes buf_end negative. The loop guard then compares the u32
urb->transfer_buffer_length against that negative int: the usual
arithmetic conversion turns buf_end into a large unsigned value, so the
guard stays true and each iteration keeps appending SysEx framing and
payload bytes past the end of the URB transfer buffer, which is only
max_transfer bytes long.
A USB device that advertises a tiny bulk-OUT endpoint can therefore
trigger an attacker-length- and content-controlled heap out-of-bounds
write when a process writes to the created /dev/snd/midiC*D* node.
Return early when there is no room for even one SysEx, so the loop is
never entered with a bound that would wrap. The loop is the last
statement of the function, so bailing out is equivalent to it not
running.
Discovered by XBOW, triaged by Baul Lee <baul.lee@xbow.com>
Fixes: 4434ade8c9 ("ALSA: usb-audio: add support for Akai MPD16")
Suggested-by: Takashi Iwai <tiwai@suse.de>
Reported-by: Federico Kirschbaum <federico.kirschbaum@xbow.com>
Reported-by: Baul Lee <baul.lee@xbow.com>
Cc: stable@vger.kernel.org
Signed-off-by: Baul Lee <baul.lee@xbow.com>
Link: https://patch.msgid.link/20260726074500.50145-1-baul.lee@xbow.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
