When the Linear Link Position is not available in firmware SRAM window we
use the host accessible position registers to read it.
The address of the PPLCLLPL/U registers depend on the number of streams
(playback+capture).
At probe time the pplc_addr is calculated for each stream and we can use
it to read the LLP without the need of address re-calculation.
Set the get_stream_position callback in sof_hda_common_ops for all
platforms:
The callback is used for IPC4 delay calculations only but the register is
a generic HDA register, not tied to any specific IPC version.
Cc: stable@vger.kernel.org # 6.8
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://msgid.link/r/20240321130814.4412-5-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If the PCM have the dsp_max_burst_size_in_ms set then place a constraint
to limit the minimum buffer time to avoid xruns caused by DMA bursts
spinning on the ALSA buffer.
Cc: stable@vger.kernel.org # 6.8
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://msgid.link/r/20240321130814.4412-4-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When setting up the pcm widget, save the DSP buffer size (in ms) for
platform code to place a constraint on playback.
On playback the DMA will fill the buffer on start and if the period
size is smaller it will immediately overrun.
On capture the DMA will move data in 1ms bursts.
Cc: stable@vger.kernel.org # 6.8
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://msgid.link/r/20240321130814.4412-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The dsp_max_burst_size_in_ms can be used to save the length of the maximum
burst size in ms the host DMA will use.
Platform code can place constraint using this to avoid user space
requesting too small ALSA buffer which will result xruns.
Cc: stable@vger.kernel.org # 6.8
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://msgid.link/r/20240321130814.4412-2-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Initialization is completed before adding the component as that can
start the process of the device binding and trigger actions that check
init_done.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 73cfbfa9ca ("ALSA: hda/cs35l56: Add driver for Cirrus Logic CS35L56 amplifier")
Message-ID: <20240325145510.328378-1-rf@opensource.cirrus.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The system and amplifier names influence which firmware and tuning files
are downloaded to the device; log these values to aid end-user system
support.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Message-ID: <20240325142937.257869-1-rf@opensource.cirrus.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Complete the example of recommended order of properties by adding
missing address/size-cells. They are not necessary to illustrate the
style, but lack of them us bit really correct DTS code which might
confuse readers.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/20240325091139.18602-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Rob Herring <robh@kernel.org>
Bindings for a given device class generally go to the respective
subsystem maintainers. Add the TPM bindings to the TPM
maintainers entry.
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.ogr>
Link: https://lore.kernel.org/r/20240130215917.2473250-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
sk->sk_rcvbuf in __sock_queue_rcv_skb() and __sk_receive_skb() can be
changed by other threads. Mark this as benign using READ_ONCE().
This patch is aimed at reducing the number of benign races reported by
KCSAN in order to focus future debugging effort on harmful races.
Signed-off-by: linke li <lilinke99@qq.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When releasing frames from the reorder buffer, the link ID was not
included in the RX status information. This subsequently led mac80211 to
drop the frame. Change it so that the link information is set
immediately when possible so that it doesn't not need to be filled in
anymore when submitting the frame to mac80211.
Fixes: b8a85a1d42 ("wifi: iwlwifi: mvm: rxmq: report link ID to mac80211")
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Tested-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240320232419.bbbd5e9bfe80.Iec1bf5c884e371f7bc5ea2534ed9ea8d3f2c0bf6@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With debugfs=off, we can get here with the dbgfs_dir being
an ERR_PTR(). Instead of checking for all this, which is
often flagged as a mistake, simply handle the names here
more carefully by printing them, then we don't need extra
checks.
Also, while checking, I noticed theoretically 'buf' is too
small, so fix that size as well.
Cc: stable@vger.kernel.org
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218422
Fixes: c36235acb3 ("wifi: iwlwifi: mvm: rework debugfs handling")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240320232419.4dc1eb3dd015.I32f308b0356ef5bcf8d188dd98ce9b210e3ab9fd@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Guard against invalid station IDs in iwl_mvm_mld_rm_sta_id as that would
result in out-of-bounds array accesses. This prevents issues should the
driver get into a bad state during error handling.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240320232419.d523167bda9c.I1cffd86363805bf86a95d8bdfd4b438bb54baddc@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If we read txq->read_ptr without lock, we can read the same
value twice, then obtain the lock, and reclaim from there
to two different places, but crucially reclaim the same
entry twice, resulting in the WARN_ONCE() a little later.
Fix that by reading txq->read_ptr under lock.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240319100755.bf4c62196504.I978a7ca56c6bd6f1bf42c15aa923ba03366a840b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since the dump_data (struct iwl_fwrt_dump_data) is a union,
it's not safe to unconditionally access and use the 'trig'
member, it might be 'desc' instead. Access it only if it's
known to be 'trig' rather than 'desc', i.e. if ini-debug
is present.
Cc: stable@vger.kernel.org
Fixes: 0eb50c674a ("iwlwifi: yoyo: send hcmd to fw after dump collection completes.")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240319100755.e2976bc58b29.I72fbd6135b3623227de53d8a2bb82776066cb72b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the rx payload length check fails, or if kmemdup() fails,
we still need to free the command response. Fix that.
Fixes: 21254908cb ("iwlwifi: mvm: add RFI-M support")
Co-authored-by: Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240319100755.db2fa0196aa7.I116293b132502ac68a65527330fa37799694b79c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix ieee80211_ttlm_set_links() to not set all active links,
but instead let the driver know that valid links status changed
and select the active links properly.
Fixes: 8f500fbc6c ("wifi: mac80211: process and save negotiated TID to Link mapping request")
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240318184907.acddbbf39584.Ide858f95248fcb3e483c97fcaa14b0cd4e964b10@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the non MLD firmware flows, although the deflink is used, the mapping
of link ID to BSS configuration was missing, which causes flows that need
this mapping to crash.
Fix this by adding the link ID to BSS configuration mapping to non MLD
flows as well.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240311081938.0b5c361e8f0c.Ib11f41815d2efa5d1ec57f855de4c8563142987b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Do not call iwl_mvm_mld_get_primary_link if only one link
is active.
In that case, the sole active link should be used.
iwl_mvm_mld_get_primary_link returns -1 if only one link
is active causing a warning.
Fixes: 8c9bef26e9 ("wifi: iwlwifi: mvm: d3: implement suspend with MLO")
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240311081938.6c50061bf69b.I05b0ac7fa7149eabaa5570a6f65b0d9bfb09a6f1@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If prep_channel fails in prep_connection, the code releases
the deflink's chanctx, which is wrong since we may be using
a different link. It's already wrong to even do that always
though, since we might still have the station. Remove it
only if prep_channel succeeded and later updates fail.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240318184907.2780c1f08c3d.I033c9b15483933088f32a2c0789612a33dd33d82@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix the order of arguments in the TP_ARGS macro
for the rdev_dump_mpp tracepoint event.
Found by Linux Verification Center (linuxtesting.org).
Signed-off-by: Igor Artemiev <Igor.A.Artemiev@mcst.ru>
Link: https://msgid.link/20240311164519.118398-1-Igor.A.Artemiev@mcst.ru
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
MLO ended up not really fully stable yet, we want to make
sure it works well with the ecosystem before enabling it.
Thus, remove the flag, but set WIPHY_FLAG_DISABLE_WEXT so
we don't get wireless extensions back until we enable MLO
for this hardware.
Cc: stable@vger.kernel.org
Reviewed-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240314110951.d6ad146df98d.I47127e4fdbdef89e4ccf7483641570ee7871d4e6@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Wireless extensions are already disabled if MLO is enabled,
given that we cannot support MLO there with all the hard-
coded assumptions about BSSID etc.
However, the WiFi7 ecosystem is still stabilizing, and some
devices may need MLO disabled while that happens. In that
case, we might end up with a device that supports wext (but
not MLO) in one kernel, and then breaks wext in the future
(by enabling MLO), which is not desirable.
Add a flag to let such drivers/devices disable wext even if
MLO isn't yet enabled.
Cc: stable@vger.kernel.org
Link: https://msgid.link/20240314110951.b50f1dc4ec21.I656ddd8178eedb49dc5c6c0e70f8ce5807afb54f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Running kernel-doc on ieee80211_i.h flagged the following:
net/mac80211/ieee80211_i.h:145: warning: expecting prototype for enum ieee80211_corrupt_data_flags. Prototype was for enum ieee80211_bss_corrupt_data_flags instead
net/mac80211/ieee80211_i.h:162: warning: expecting prototype for enum ieee80211_valid_data_flags. Prototype was for enum ieee80211_bss_valid_data_flags instead
Fix these warnings.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://msgid.link/20240314-kdoc-ieee80211_i-v1-1-72b91b55b257@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When moving a station out of a VLAN and deleting the VLAN afterwards, the
fast_rx entry still holds a pointer to the VLAN's netdev, which can cause
use-after-free bugs. Fix this by immediately calling ieee80211_check_fast_rx
after the VLAN change.
Cc: stable@vger.kernel.org
Reported-by: ranygh@riseup.net
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://msgid.link/20240316074336.40442-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make sure that the new mlme_link_id_dbg() macro honours
CONFIG_MAC80211_MLME_DEBUG as intended to avoid spamming the log with
messages like:
wlan0: no EHT support, limiting to HE
wlan0: determined local STA to be HE, BW limited to 160 MHz
wlan0: determined AP xx:xx:xx:xx:xx:xx to be VHT
wlan0: connecting with VHT mode, max bandwidth 160 MHz
Fixes: 310c8387c6 ("wifi: mac80211: clean up connection process")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://msgid.link/20240325085948.26203-1-johan+linaro@kernel.org
Tested-by: Kalle Valo <kvalo@kernel.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If an iget fails due to not being able to retrieve information
from the server then the inode structure is only partially
initialized. When the inode gets evicted, references to
uninitialized structures (like fscache cookies) were being
made.
This patch checks for a bad_inode before doing anything other
than clearing the inode from the cache. Since the inode is
bad, it shouldn't have any state associated with it that needs
to be written back (and there really isn't a way to complete
those anyways).
Reported-by: syzbot+eb83fe1cce5833cd66a0@syzkaller.appspotmail.com
Signed-off-by: Eric Van Hensbergen <ericvh@kernel.org>
"PM runtime functions" was been added in sdhci-omap driver in commit
f433e8aac6 ("mmc: sdhci-omap: Implement PM runtime functions") along
with "card power off and enable aggressive PM" in commit 3edf588e7f
("mmc: sdhci-omap: Allow SDIO card power off and enable aggressive PM").
Since then, the sdhci-omap driver doesn't work using mmc-hs200 mode
due to the tuning values being lost during a pm transition.
As for the sdhci_am654 driver, request a new tuning sequence before
suspend (sdhci_omap_runtime_suspend()), otherwise the device will
trigger cache flush error:
mmc1: cache flush error -110 (ETIMEDOUT)
mmc1: error -110 doing aggressive suspend
followed by I/O errors produced by fdisk -l /dev/mmcblk1boot1:
I/O error, dev mmcblk1boot0, sector 64384 op 0x0:(READ) flags 0x80700 phys_seg 1
prio class 2
I/O error, dev mmcblk1boot1, sector 64384 op 0x0:(READ) flags 0x80700 phys_seg 1
prio class 2
I/O error, dev mmcblk1boot1, sector 64384 op 0x0:(READ) flags 0x0 phys_seg 1
prio class 2
Buffer I/O error on dev mmcblk1boot1, logical block 8048, async page read
I/O error, dev mmcblk1boot0, sector 64384 op 0x0:(READ) flags 0x0 phys_seg 1
prio class 2
Buffer I/O error on dev mmcblk1boot0, logical block 8048, async page read
Don't re-tune if auto retuning is supported in HW (when SDHCI_TUNING_MODE_3
is available).
Link: https://lore.kernel.org/all/2e5f1997-564c-44e4-b357-6343e0dae7ab@smile.fr
Fixes: f433e8aac6 ("mmc: sdhci-omap: Implement PM runtime functions")
Signed-off-by: Romain Naour <romain.naour@skf.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240315234444.816978-1-romain.naour@smile.fr
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-fsanitize=thread (KCSAN) is at the moment incompatible
with named address spaces in a similar way as KASAN -
see GCC PR sanitizer/111736:
https://gcc.gnu.org/bugzilla/show_bug.cgi?id=111736
The patch disables named address spaces with KCSAN.
Reported-by: kernel test robot <oliver.sang@intel.com>
Signed-off-by: Uros Bizjak <ubizjak@gmail.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lore.kernel.org/r/20240325110128.615933-1-ubizjak@gmail.com
The mlxbf_gige_open() routine starts the PHY as part of normal
initialization. The mlxbf_gige_open() routine must stop the
PHY during its error paths.
Fixes: f92e1869d7 ("Add Mellanox BlueField Gigabit Ethernet driver")
Signed-off-by: David Thompson <davthompson@nvidia.com>
Reviewed-by: Asmaa Mnebhi <asmaa@nvidia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit d794734c9b.
While the original change tries to fix a bug, it also unintentionally broke
existing systems, see the regressions reported at:
https://lore.kernel.org/all/3a1b9909-45ac-4f97-ad68-d16ef1ce99db@pavinjoseph.com/
Since d794734c9b was also marked for -stable, let's back it out before
causing more damage.
Note that due to another upstream change the revert was not 100% automatic:
0a845e0f63 mm/treewide: replace pud_large() with pud_leaf()
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: <stable@vger.kernel.org>
Cc: Russ Anderson <rja@hpe.com>
Cc: Steve Wahl <steve.wahl@hpe.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://lore.kernel.org/all/3a1b9909-45ac-4f97-ad68-d16ef1ce99db@pavinjoseph.com/
Fixes: d794734c9b ("x86/mm/ident_map: Use gbpages only where full GB page should be mapped.")
Currently, the LBR code assumes that LBR Freeze is supported on all processors
when X86_FEATURE_AMD_LBR_V2 is available i.e. CPUID leaf 0x80000022[EAX]
bit 1 is set. This is incorrect as the availability of the feature is
additionally dependent on CPUID leaf 0x80000022[EAX] bit 2 being set,
which may not be set for all Zen 4 processors.
Define a new feature bit for LBR and PMC freeze and set the freeze enable bit
(FLBRI) in DebugCtl (MSR 0x1d9) conditionally.
It should still be possible to use LBR without freeze for profile-guided
optimization of user programs by using an user-only branch filter during
profiling. When the user-only filter is enabled, branches are no longer
recorded after the transition to CPL 0 upon PMI arrival. When branch
entries are read in the PMI handler, the branch stack does not change.
E.g.
$ perf record -j any,u -e ex_ret_brn_tkn ./workload
Since the feature bit is visible under flags in /proc/cpuinfo, it can be
used to determine the feasibility of use-cases which require LBR Freeze
to be supported by the hardware such as profile-guided optimization of
kernels.
Fixes: ca5b7c0d96 ("perf/x86/amd/lbr: Add LbrExtV2 branch record support")
Signed-off-by: Sandipan Das <sandipan.das@amd.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/69a453c97cfd11c6f2584b19f937fe6df741510f.1711091584.git.sandipan.das@amd.com
SCMI raw debugfs entries are used to inject and snoop messages out of the
SCMI core and, as such, the underlying virtual files have no reason to
support seeking.
Modify the related file_operations descriptors to be non-seekable.
Fixes: 3c3d818a93 ("firmware: arm_scmi: Add core raw transmission support")
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20240315140324.231830-1-cristian.marussi@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Fastchannels are initialized with an incorrect index(POWERCAP_PAI_GET) in:
commit 2441caa84a ("firmware: arm_scmi: Populate fast channel rate_limit")
Fix this and provide a correct index(POWERCAP_FC_PAI)
Fixes: 2441caa84a ("firmware: arm_scmi: Populate fast channel rate_limit")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/r/202403100744.7Op3PI8L-lkp@intel.com/
Signed-off-by: Pierre Gondois <pierre.gondois@arm.com>
Link: https://lore.kernel.org/r/20240311090413.1710725-1-pierre.gondois@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
FFA_NOTIFICATION_INFO_GET retrieves information about pending
notifications. Notifications can be either global or per VCPU. Global
notifications are reported with the partition ID only in the list of
endpoints with pending notifications. ffa_notification_info_get()
incorrectly expect no ID at all for global notifications. Fix this by
checking for ID = 1 instead of ID = 0.
Fixes: 3522be48d8 ("firmware: arm_ffa: Implement the NOTIFICATION_INFO_GET interface")
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Reviewed-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Link: https://lore.kernel.org/r/20240311110700.2367142-1-jens.wiklander@linaro.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The writes to setipnum_le/be register for APLIC in MSI-mode have special
consideration for level-triggered interrupts as-per the section "4.9.2
Special consideration for level-sensitive interrupt sources" of the RISC-V
AIA specification.
Particularly, the below text from the RISC-V AIA specification defines
the behaviour of writes to setipnum_le/be register for level-triggered
interrupts:
"A second option is for the interrupt service routine to write the
APLIC’s source identity number for the interrupt to the domain’s
setipnum register just before exiting. This will cause the interrupt’s
pending bit to be set to one again if the source is still asserting
an interrupt, but not if the source is not asserting an interrupt."
Fix setipnum_le/be write emulation for in-kernel APLIC by implementing
the above behaviour in aplic_write_pending() function.
Cc: stable@vger.kernel.org
Fixes: 74967aa208 ("RISC-V: KVM: Add in-kernel emulation of AIA APLIC")
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
Link: https://lore.kernel.org/r/20240321085041.1955293-2-apatel@ventanamicro.com
There are spelling mistakes in __GUEST_ASSERT messages. Fix them.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Acked-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Anup Patel <anup@brainfault.org>
Link: https://lore.kernel.org/r/20240307081951.1954830-1-colin.i.king@gmail.com
Fix to initialize 'val' local variable with zero.
Dan reported that Smatch static code checker reports an error that a local
'val' variable needs to be initialized. Actually, the 'val' is expected to
be initialized by FETCH_OP_ARG in the same loop, but it is not obvious. So
initialize it with zero.
Link: https://lore.kernel.org/all/171092223833.237219.17304490075697026697.stgit@devnote2/
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/all/b010488e-68aa-407c-add0-3e059254aaa0@moroto.mountain/
Fixes: 25f00e40ce ("tracing/probes: Support $argN in return probe (kprobe and fprobe)")
Reviewed-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
22e8e19 has introduced a regression in the imgchip->pwm_clk lookup, whereas
the clock name has also been renamed to "imgchip". This causes the driver
failing to load:
[ 0.546905] img-pwm 18101300.pwm: failed to get imgchip clock
[ 0.553418] img-pwm: probe of 18101300.pwm failed with error -2
Fix this lookup by reverting the clock name back to "pwm".
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Link: https://lore.kernel.org/r/20240320083602.81592-1-wigyori@uid0.hu
Fixes: 22e8e19a46 ("pwm: img: Rename variable pointing to driver private data")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
syzbot reported an ext4 panic during a page fault where found a
journal handle when it didn't expect to find one. The structure
it tripped over had a value of 'TRAN' in the first entry in the
structure, and that indicates it tripped over a struct xfs_trans
instead of a jbd2 handle.
The reason for this is that the page fault was taken during a
copy-out to a user buffer from an xfs bulkstat operation. XFS uses
an "empty" transaction context for bulkstat to do automated metadata
buffer cleanup, and so the transaction context is valid across the
copyout of the bulkstat info into the user buffer.
We are using empty transaction contexts like this in XFS to reduce
the risk of failing to release objects we reference during the
operation, especially during error handling. Hence we really need to
ensure that we can take page faults from these contexts without
leaving landmines for the code processing the page fault to trip
over.
However, this same behaviour could happen from any other filesystem
that triggers a page fault or any other exception that is handled
on-stack from within a task context that has current->journal_info
set. Having a page fault from some other filesystem bounce into XFS
where we have to run a transaction isn't a bug at all, but the usage
of current->journal_info means that this could result corruption of
the outer task's journal_info structure.
The problem is purely that we now have two different contexts that
now think they own current->journal_info. IOWs, no filesystem can
allow page faults or on-stack exceptions while current->journal_info
is set by the filesystem because the exception processing might use
current->journal_info itself.
If we end up with nested XFS transactions whilst holding an empty
transaction, then it isn't an issue as the outer transaction does
not hold a log reservation. If we ignore the current->journal_info
usage, then the only problem that might occur is a deadlock if the
exception tries to take the same locks the upper context holds.
That, however, is not a problem that setting current->journal_info
would solve, so it's largely an irrelevant concern here.
IOWs, we really only use current->journal_info for a warning check
in xfs_vm_writepages() to ensure we aren't doing writeback from a
transaction context. Writeback might need to do allocation, so it
can need to run transactions itself. Hence it's a debug check to
warn us that we've done something silly, and largely it is not all
that useful.
So let's just remove all the use of current->journal_info in XFS and
get rid of all the potential issues from nested contexts where
current->journal_info might get misused by another filesystem
context.
Reported-by: syzbot+cdee56dbcdf0096ef605@syzkaller.appspotmail.com
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: "Darrick J. Wong" <djwong@kernel.org>
Reviewed-by: Mark Tinguely <mark.tinguely@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Chandan Babu R <chandanbabu@kernel.org>
If a filesystem has a busted stripe alignment configuration on disk
(e.g. because broken RAID firmware told mkfs that swidth was smaller
than sunit), then the filesystem will refuse to mount due to the
stripe validation failing. This failure is triggering during distro
upgrades from old kernels lacking this check to newer kernels with
this check, and currently the only way to fix it is with offline
xfs_db surgery.
This runtime validity checking occurs when we read the superblock
for the first time and causes the mount to fail immediately. This
prevents the rewrite of stripe unit/width via
mount options that occurs later in the mount process. Hence there is
no way to recover this situation without resorting to offline xfs_db
rewrite of the values.
However, we parse the mount options long before we read the
superblock, and we know if the mount has been asked to re-write the
stripe alignment configuration when we are reading the superblock
and verifying it for the first time. Hence we can conditionally
ignore stripe verification failures if the mount options specified
will correct the issue.
We validate that the new stripe unit/width are valid before we
overwrite the superblock values, so we can ignore the invalid config
at verification and fail the mount later if the new values are not
valid. This, at least, gives users the chance of correcting the
issue after a kernel upgrade without having to resort to xfs-db
hacks.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: "Darrick J. Wong" <djwong@kernel.org>
Signed-off-by: Chandan Babu R <chandanbabu@kernel.org>
I have been contributing to erofs for sometime and I would like to help
with code reviews as well.
Signed-off-by: Sandeep Dhavale <dhavale@google.com>
Acked-by: Chao Yu <chao@kernel.org>
Reviewed-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Link: https://lore.kernel.org/r/20240314231407.1000541-1-dhavale@google.com
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
