mirror of
https://github.com/torvalds/linux.git
synced 2026-08-01 03:59:40 +02:00
ff712188da
1336144 Commits
| Author | SHA1 | Message | Date | |
|---|---|---|---|---|
Miao Li
|
ff712188da |
usb: quirks: Add DELAY_INIT and NO_LPM for Prolific Mass Storage Card Reader
When used on Huawei hisi platforms, Prolific Mass Storage Card Reader which the VID:PID is in 067b:2731 might fail to enumerate at boot time and doesn't work well with LPM enabled, combination quirks: USB_QUIRK_DELAY_INIT + USB_QUIRK_NO_LPM fixed the problems. Signed-off-by: Miao Li <limiao@kylinos.cn> Cc: stable <stable@kernel.org> Link: https://lore.kernel.org/r/20250304070757.139473-1-limiao870622@163.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> |
||
|
Michal Pecio
|
c7c1f3b05c |
usb: xhci: Fix host controllers "dying" after suspend and resume
A recent cleanup went a bit too far and dropped clearing the cycle bit
of link TRBs, so it stays different from the rest of the ring half of
the time. Then a race occurs: if the xHC reaches such link TRB before
more commands are queued, the link's cycle bit unintentionally matches
the xHC's cycle so it follows the link and waits for further commands.
If more commands are queued before the xHC gets there, inc_enq() flips
the bit so the xHC later sees a mismatch and stops executing commands.
This function is called before suspend and 50% of times after resuming
the xHC is doomed to get stuck sooner or later. Then some Stop Endpoint
command fails to complete in 5 seconds and this shows up
xhci_hcd 0000:00:10.0: xHCI host not responding to stop endpoint command
xhci_hcd 0000:00:10.0: xHCI host controller not responding, assume dead
xhci_hcd 0000:00:10.0: HC died; cleaning up
followed by loss of all USB decives on the affected bus. That's if you
are lucky, because if Set Deq gets stuck instead, the failure is silent.
Likely responsible for kernel bug 219824. I found this while searching
for possible causes of that regression and reproduced it locally before
hearing back from the reporter. To repro, simply wait for link cycle to
become set (debugfs), then suspend, resume and wait. To accelerate the
failure I used a script which repeatedly starts and stops a UVC camera.
Some HCs get fully reinitialized on resume and they are not affected.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=219824
Fixes:
|
||
|
Thinh Nguyen
|
cc5bfc4e16 |
usb: dwc3: Set SUSPENDENABLE soon after phy init
After phy initialization, some phy operations can only be executed while
in lower P states. Ensure GUSB3PIPECTL.SUSPENDENABLE and
GUSB2PHYCFG.SUSPHY are set soon after initialization to avoid blocking
phy ops.
Previously the SUSPENDENABLE bits are only set after the controller
initialization, which may not happen right away if there's no gadget
driver or xhci driver bound. Revise this to clear SUSPENDENABLE bits
only when there's mode switching (change in GCTL.PRTCAPDIR).
Fixes:
|
||
|
Pawel Laszczak
|
2b66ef84d0 |
usb: hub: lack of clearing xHC resources
The xHC resources allocated for USB devices are not released in correct
order after resuming in case when while suspend device was reconnected.
This issue has been detected during the fallowing scenario:
- connect hub HS to root port
- connect LS/FS device to hub port
- wait for enumeration to finish
- force host to suspend
- reconnect hub attached to root port
- wake host
For this scenario during enumeration of USB LS/FS device the Cadence xHC
reports completion error code for xHC commands because the xHC resources
used for devices has not been properly released.
XHCI specification doesn't mention that device can be reset in any order
so, we should not treat this issue as Cadence xHC controller bug.
Similar as during disconnecting in this case the device resources should
be cleared starting form the last usb device in tree toward the root hub.
To fix this issue usbcore driver should call hcd->driver->reset_device
for all USB devices connected to hub which was reconnected while
suspending.
Fixes:
|
||
|
Claudiu Beznea
|
552ca6b87e |
usb: renesas_usbhs: Flush the notify_hotplug_work
When performing continuous unbind/bind operations on the USB drivers
available on the Renesas RZ/G2L SoC, a kernel crash with the message
"Unable to handle kernel NULL pointer dereference at virtual address"
may occur. This issue points to the usbhsc_notify_hotplug() function.
Flush the delayed work to avoid its execution when driver resources are
unavailable.
Fixes:
|
||
|
Claudiu Beznea
|
e0c9244093 |
usb: renesas_usbhs: Use devm_usb_get_phy()
The gpriv->transceiver is retrieved in probe() through usb_get_phy() but
never released. Use devm_usb_get_phy() to handle this scenario.
This issue was identified through code investigation. No issue was found
without this change.
Fixes:
|
||
|
Claudiu Beznea
|
b5ea08aa88 |
usb: renesas_usbhs: Call clk_put()
Clocks acquired with of_clk_get() need to be freed with clk_put(). Call
clk_put() on priv->clks[0] on error path.
Fixes:
|
||
|
Badhri Jagan Sridharan
|
69c58deec1 |
usb: dwc3: gadget: Prevent irq storm when TH re-executes
While commit |
||
|
Prashanth K
|
8e812e9355 |
usb: gadget: Check bmAttributes only if configuration is valid
If the USB configuration is not valid, then avoid checking for
bmAttributes to prevent null pointer deference.
Cc: stable <stable@kernel.org>
Fixes:
|
||
|
Marc Zyngier
|
487cfd4a8e |
xhci: Restrict USB4 tunnel detection for USB3 devices to Intel hosts
When adding support for USB3-over-USB4 tunnelling detection, a check
for an Intel-specific capability was added. This capability, which
goes by ID 206, is used without any check that we are actually
dealing with an Intel host.
As it turns out, the Cadence XHCI controller *also* exposes an
extended capability numbered 206 (for unknown purposes), but of
course doesn't have the Intel-specific registers that the tunnelling
code is trying to access. Fun follows.
The core of the problems is that the tunnelling code blindly uses
vendor-specific capabilities without any check (the Intel-provided
documentation I have at hand indicates that 192-255 are indeed
vendor-specific).
Restrict the detection code to Intel HW for real, preventing any
further explosion on my (non-Intel) HW.
Cc: stable <stable@kernel.org>
Fixes:
|
||
|
Michal Pecio
|
c133ec0e57 |
usb: xhci: Enable the TRB overfetch quirk on VIA VL805
Raspberry Pi is a major user of those chips and they discovered a bug - when the end of a transfer ring segment is reached, up to four TRBs can be prefetched from the next page even if the segment ends with link TRB and on page boundary (the chip claims to support standard 4KB pages). It also appears that if the prefetched TRBs belong to a different ring whose doorbell is later rung, they may be used without refreshing from system RAM and the endpoint will stay idle if their cycle bit is stale. Other users complain about IOMMU faults on x86 systems, unsurprisingly. Deal with it by using existing quirk which allocates a dummy page after each transfer ring segment. This was seen to resolve both problems. RPi came up with a more efficient solution, shortening each segment by four TRBs, but it complicated the driver and they ditched it for this quirk. Also rename the quirk and add VL805 device ID macro. Signed-off-by: Michal Pecio <michal.pecio@gmail.com> Link: https://github.com/raspberrypi/linux/issues/4685 Closes: https://bugzilla.kernel.org/show_bug.cgi?id=215906 CC: stable@vger.kernel.org Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20250225095927.2512358-2-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> |
||
|
Marek Szyprowski
|
c783e1258f |
usb: gadget: Fix setting self-powered state on suspend
cdev->config might be NULL, so check it before dereferencing.
CC: stable <stable@kernel.org>
Fixes:
|
||
|
Fedor Pchelkin
|
bf4f9ae1cb |
usb: typec: ucsi: increase timeout for PPM reset operations
It is observed that on some systems an initial PPM reset during the boot
phase can trigger a timeout:
[ 6.482546] ucsi_acpi USBC000:00: failed to reset PPM!
[ 6.482551] ucsi_acpi USBC000:00: error -ETIMEDOUT: PPM init failed
Still, increasing the timeout value, albeit being the most straightforward
solution, eliminates the problem: the initial PPM reset may take up to
~8000-10000ms on some Lenovo laptops. When it is reset after the above
period of time (or even if ucsi_reset_ppm() is not called overall), UCSI
works as expected.
Moreover, if the ucsi_acpi module is loaded/unloaded manually after the
system has booted, reading the CCI values and resetting the PPM works
perfectly, without any timeout. Thus it's only a boot-time issue.
The reason for this behavior is not clear but it may be the consequence
of some tricks that the firmware performs or be an actual firmware bug.
As a workaround, increase the timeout to avoid failing the UCSI
initialization prematurely.
Fixes:
|
||
|
Christian A. Ehrhardt
|
976e7e9bdc |
acpi: typec: ucsi: Introduce a ->poll_cci method
For the ACPI backend of UCSI the UCSI "registers" are just a memory copy
of the register values in an opregion. The ACPI implementation in the
BIOS ensures that the opregion contents are synced to the embedded
controller and it ensures that the registers (in particular CCI) are
synced back to the opregion on notifications. While there is an ACPI call
that syncs the actual registers to the opregion there is rarely a need to
do this and on some ACPI implementations it actually breaks in various
interesting ways.
The only reason to force a sync from the embedded controller is to poll
CCI while notifications are disabled. Only the ucsi core knows if this
is the case and guessing based on the current command is suboptimal, i.e.
leading to the following spurious assertion splat:
WARNING: CPU: 3 PID: 76 at drivers/usb/typec/ucsi/ucsi.c:1388 ucsi_reset_ppm+0x1b4/0x1c0 [typec_ucsi]
CPU: 3 UID: 0 PID: 76 Comm: kworker/3:0 Not tainted 6.12.11-200.fc41.x86_64 #1
Hardware name: LENOVO 21D0/LNVNB161216, BIOS J6CN45WW 03/17/2023
Workqueue: events_long ucsi_init_work [typec_ucsi]
RIP: 0010:ucsi_reset_ppm+0x1b4/0x1c0 [typec_ucsi]
Call Trace:
<TASK>
ucsi_init_work+0x3c/0xac0 [typec_ucsi]
process_one_work+0x179/0x330
worker_thread+0x252/0x390
kthread+0xd2/0x100
ret_from_fork+0x34/0x50
ret_from_fork_asm+0x1a/0x30
</TASK>
Thus introduce a ->poll_cci() method that works like ->read_cci() with an
additional forced sync and document that this should be used when polling
with notifications disabled. For all other backends that presumably don't
have this issue use the same implementation for both methods.
Fixes:
|
||
|
AngeloGioacchino Del Regno
|
d6b82dafd1 |
usb: typec: tcpci_rt1711h: Unmask alert interrupts to fix functionality
During probe, the TCPC alert interrupts are getting masked to
avoid unwanted interrupts during chip setup: this is ok to do
but there is no unmasking happening at any later time, which
means that the chip will not raise any interrupt, essentially
making it not functional as, while internally it does perform
all of the intended functions, it won't signal anything to the
outside.
Unmask the alert interrupts to fix functionality.
Fixes:
|
||
|
Prashanth K
|
40e89ff575 |
usb: gadget: Set self-powered based on MaxPower and bmAttributes
Currently the USB gadget will be set as bus-powered based solely
on whether its bMaxPower is greater than 100mA, but this may miss
devices that may legitimately draw less than 100mA but still want
to report as bus-powered. Similarly during suspend & resume, USB
gadget is incorrectly marked as bus/self powered without checking
the bmAttributes field. Fix these by configuring the USB gadget
as self or bus powered based on bmAttributes, and explicitly set
it as bus-powered if it draws more than 100mA.
Cc: stable <stable@kernel.org>
Fixes:
|
||
|
Prashanth K
|
17c2c87c37 |
usb: gadget: u_ether: Set is_suspend flag if remote wakeup fails
Currently while UDC suspends, u_ether attempts to remote wakeup
the host if there are any pending transfers. However, if remote
wakeup fails, the UDC remains suspended but the is_suspend flag
is not set. And since is_suspend flag isn't set, the subsequent
eth_start_xmit() would queue USB requests to suspended UDC.
To fix this, bail out from gether_suspend() only if remote wakeup
operation is successful.
Cc: stable <stable@kernel.org>
Fixes:
|
||
|
Nikita Zhandarovich
|
c90aad3698 |
usb: atm: cxacru: fix a flaw in existing endpoint checks
Syzbot once again identified a flaw in usb endpoint checking, see [1]. This time the issue stems from a commit authored by me ( |
||
|
Linus Torvalds
|
0ad2507d5d | Linux 6.14-rc3 | ||
|
Linus Torvalds
|
224e745110 |
Kbuild fixes for v6.14 (2nd)
- Fix annoying logs when building tools in parallel - Fix the Debian linux-headers package build again - Fix the target triple detection for userspace programs on Clang -----BEGIN PGP SIGNATURE----- iQJJBAABCgAzFiEEbmPs18K1szRHjPqEPYsBB53g2wYFAmeyExkVHG1hc2FoaXJv eUBrZXJuZWwub3JnAAoJED2LAQed4NsGtEIQAJNiuG2KvXawT8BdDE1RMM25bJiE 3mkqexYAWionInz44WzAwMuzXG3yLFxeuLynh926qw8eE832s2ngMzJluFQehl53 QP/KVpzFliPyO+nRWPcsRi2Re8wL3TD3lnJLt58yNJlpBmF7pc9TYFUrMuRqFE/1 1h2BlCOYYuq24mMY4F7ULESQ/4Bpb+4dGkN/WXtPttYFmNl+sPy9vn3lG3DxzLKM UjwAmRhta/sFV3UF6nWcb1jsiti7IkHf/WIZPm8MoMjBNetnSkfcesPeLhaI7waf +TVa9JqwoFWgscGXlCpK/Pw/gOQr1Lf0ZuSMNxtJe9vU76rEoLmdUYaHNbnA6CvQ wj6HA7E4mownOzKu3gqZ76dqoaHYdmeHTSoyDCJqVFzicI7ZDYT8MaggFGH/F10J KZ7daYOV6HYJxGVTYuhD1e2RvOZcXUHzxafTyl0Hyi1z3z+pWOKLE6W/uDvRkW32 qCubjZwgepHuI/TUos9VIkkIiW2429Sb4kgqQTRBtzRdKdM+qGjTEzLV/3KPuaWj 0qCiF6sf7shzgk4UstrUQ7JN+V5oLJUgY/TKZuPyy69qE6xYqUWvRmnGkYxav8aM 5lTGMXWViksO+EebeE0sNH+R3XHXAxVTI95s4kX57SPcAHItTSMGPPVe2bRErwWJ hiLEu6gRezp/7IDT =56TH -----END PGP SIGNATURE----- Merge tag 'kbuild-fixes-v6.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild Pull Kbuild fixes from Masahiro Yamada: - Fix annoying logs when building tools in parallel - Fix the Debian linux-headers package build again - Fix the target triple detection for userspace programs on Clang * tag 'kbuild-fixes-v6.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: modpost: Fix a few typos in a comment kbuild: userprogs: fix bitsize and target detection on clang kbuild: fix linux-headers package build when $(CC) cannot link userspace tools: fix annoying "mkdir -p ..." logs when building tools in parallel |
||
|
Linus Torvalds
|
ae5fa8ce7e |
Driver core api addition for 6.14-rc3
Here is a driver core new api for 6.14-rc3 that is being added to allow platform devices from stop being abused. It adds a new "faux_device" structure and bus and api to allow almost a straight or simpler conversion from platform devices that were not really a platform device. It also comes with a binding for rust, with an example driver in rust showing how it's used. I'm adding this now so that the patches that convert the different drivers and subsystems can all start flowing into linux-next now through their different development trees, in time for 6.15-rc1. We have a number that are already reviewed and tested, but adding those conversions now doesn't seem right. For now, no one is using this, and it passes all build tests from 0-day and linux-next, so all should be good. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> -----BEGIN PGP SIGNATURE----- iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZ7H+sQ8cZ3JlZ0Brcm9h aC5jb20ACgkQMUfUDdst+yljfwCfdP8AvZeIdx89cqS0djspBSFLw1MAoIpq7Pbi 6BY+VOuDSZNdBKXFLR/x =2qRL -----END PGP SIGNATURE----- Merge tag 'driver-core-6.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core Pull driver core api addition from Greg KH: "Here is a driver core new api for 6.14-rc3 that is being added to allow platform devices from stop being abused. It adds a new 'faux_device' structure and bus and api to allow almost a straight or simpler conversion from platform devices that were not really a platform device. It also comes with a binding for rust, with an example driver in rust showing how it's used. I'm adding this now so that the patches that convert the different drivers and subsystems can all start flowing into linux-next now through their different development trees, in time for 6.15-rc1. We have a number that are already reviewed and tested, but adding those conversions now doesn't seem right. For now, no one is using this, and it passes all build tests from 0-day and linux-next, so all should be good" * tag 'driver-core-6.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: rust/kernel: Add faux device bindings driver core: add a faux bus for use when a simple device/bus is needed |
||
|
Linus Torvalds
|
56400391b1 |
Serial driver fixes for 6.14-rc3
Here are some small serial driver fixes for some reported problems for 6.14-rc3. Nothing major, just: - sc16is7xx irq check fix - 8250 fifo underflow fix - serial_port and 8250 iotype fixes Most of these have been in linux-next already, and all have passed 0-day testing. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> -----BEGIN PGP SIGNATURE----- iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZ7H/YQ8cZ3JlZ0Brcm9h aC5jb20ACgkQMUfUDdst+ykxAwCbBpzMC3xtuqSw/PCrFGbBNeMVuQcAoKtoQYWr Zro9O1hxTOfbFNeHEVtj =XvcE -----END PGP SIGNATURE----- Merge tag 'tty-6.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty Pull serial driver fixes from Greg KH: "Here are some small serial driver fixes for some reported problems. Nothing major, just: - sc16is7xx irq check fix - 8250 fifo underflow fix - serial_port and 8250 iotype fixes Most of these have been in linux-next already, and all have passed 0-day testing" * tag 'tty-6.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: serial: 8250: Fix fifo underflow on flush serial: 8250_pnp: Remove unneeded ->iotype assignment serial: 8250_platform: Remove unneeded ->iotype assignment serial: 8250_of: Remove unneeded ->iotype assignment serial: port: Make ->iotype validation global in __uart_read_properties() serial: port: Always update ->iotype in __uart_read_properties() serial: port: Assign ->iotype correctly when ->iobase is set serial: sc16is7xx: Fix IRQ number check behavior |
||
|
Linus Torvalds
|
6bfcc5fb2f |
USB fixes for 6.14-rc3
Here are some small USB driver fixes, and new device ids, for 6.14-rc3. Lots of tiny stuff for reported problems, including: - new device ids and quirks - usb hub crash fix found by syzbot - dwc2 driver fix - dwc3 driver fixes - uvc gadget driver fix - cdc-acm driver fixes for a variety of different issues - other tiny bugfixes Almost all of these have been in linux-next this week, and all have passed 0-day testing. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> -----BEGIN PGP SIGNATURE----- iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZ7H/9Q8cZ3JlZ0Brcm9h aC5jb20ACgkQMUfUDdst+ym9YgCeIG0YNJa3Bb8gVQOnNwbOXzSpt84AniHDxqW9 EMqZy36ZYzee04t1wR0b =La/t -----END PGP SIGNATURE----- Merge tag 'usb-6.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb Pull USB fixes from Greg KH: "Here are some small USB driver fixes, and new device ids, for 6.14-rc3. Lots of tiny stuff for reported problems, including: - new device ids and quirks - usb hub crash fix found by syzbot - dwc2 driver fix - dwc3 driver fixes - uvc gadget driver fix - cdc-acm driver fixes for a variety of different issues - other tiny bugfixes Almost all of these have been in linux-next this week, and all have passed 0-day testing" * tag 'usb-6.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (25 commits) usb: typec: tcpm: PSSourceOffTimer timeout in PR_Swap enters ERROR_RECOVERY usb: roles: set switch registered flag early on usb: gadget: uvc: Fix unstarted kthread worker USB: quirks: add USB_QUIRK_NO_LPM quirk for Teclast dist usb: gadget: core: flush gadget workqueue after device removal USB: gadget: f_midi: f_midi_complete to call queue_work usb: core: fix pipe creation for get_bMaxPacketSize0 usb: dwc3: Fix timeout issue during controller enter/exit from halt state USB: Add USB_QUIRK_NO_LPM quirk for sony xperia xz1 smartphone USB: cdc-acm: Fill in Renesas R-Car D3 USB Download mode quirk usb: cdc-acm: Fix handling of oversized fragments usb: cdc-acm: Check control transfer buffer size before access usb: xhci: Restore xhci_pci support for Renesas HCs USB: pci-quirks: Fix HCCPARAMS register error for LS7A EHCI USB: serial: option: drop MeiG Smart defines USB: serial: option: fix Telit Cinterion FN990A name USB: serial: option: add Telit Cinterion FN990B compositions USB: serial: option: add MeiG Smart SLM828 usb: gadget: f_midi: fix MIDI Streaming descriptor lengths usb: dwc2: gadget: remove of_node reference upon udc_stop ... |
||
|
Linus Torvalds
|
ba643b6d84 |
- Remove an unused config item GENERIC_PENDING_IRQ_CHIPFLAGS
-----BEGIN PGP SIGNATURE----- iQIzBAABCgAdFiEEzv7L6UO9uDPlPSfHEsHwGGHeVUoFAmextVEACgkQEsHwGGHe VUpEew//bv6xE+9sUxtKpD4yQFSZmOOAYbSg6TNdxlmlIMXn2JHeOe166TiQHDIv w4QVZuzmmHx11hPC3YVgdMtzU0S/dFWd2LhoguHVALbZ39sxap2tuWIZacDvShyP WKrGAtvb/BOb0lL0yQY3dGwQ+YO7ye0EU+gJLCaWqNC7n0vWfP4gin17k08iNgQg qghwGUNCsYsijfpvimcJB9eqg00pOqnOVnWiE2xGSz5LKy+Yigtd8aNR50mS+Mgt Sl2Dzmesio0B464X+HSj34dhi4GswdjWmqKyuixmOuECp/1rCBakpuq760J0ijOg dliiBHZplavsLcis9Mh/vKzN4Pd5xjXMPsADHpTX/2fpF8yXj9sWpG+xp7UgsJi0 LZASk8LTovstOGiDSF7ff+4iCPlkZTvE77fawfdcrpe4kgUc85VpRWyv7xalbGwj 0Y/6dIkXg9dOwv+1z57i15ws2KDG35d2faF5UH1qfr/wwzp/TloIk5oX1C5d2puh Y5Fohu3S+D+wFgJB0xwkGTXzLTGVn/ElQMF08CvHHvqX3TrA9HNfJ7EahROx/T3i HNjj10YyKXbGwnk7OAQENOKG3SztlxrPk4SEEY4fZ1RvehYYu6qXXHA9vShjDQcN C2Elj42sgoTXr+DBGeVPHE1bD279kxacWZYD2xPx15t74Mu0zis= =tXlN -----END PGP SIGNATURE----- Merge tag 'irq_urgent_for_v6.14_rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull irq Kconfig cleanup from Borislav Petkov: - Remove an unused config item GENERIC_PENDING_IRQ_CHIPFLAGS * tag 'irq_urgent_for_v6.14_rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: genirq: Remove unused CONFIG_GENERIC_PENDING_IRQ_CHIPFLAGS |
||
|
Linus Torvalds
|
ff1848d81c |
- Explicitly clear DEBUGCTL.LBR to prevent LBRs continuing being enabled after
handoff to the OS - Check CPUID(0x23) leaf and subleafs presence properly - Remove the PEBS-via-PT feature from being supported on hybrid systems - Fix perf record/top default commands on systems without a raw PMU registered -----BEGIN PGP SIGNATURE----- iQIzBAABCgAdFiEEzv7L6UO9uDPlPSfHEsHwGGHeVUoFAmextCMACgkQEsHwGGHe VUr7ag/+PjtbKevbeqjQ0RtkA4TF0gpbYMQdE/h5myY4YnxjmsvuiZoNZztgKU6f 48/NJ2Fjf7cjMnTf+vYSxoTh4FmBcnhz16GyRYeF+JczR3LLf0yN/UmUz6V05kti 4pWdbgqa7pPOIVS2NQUcC+rlHNO0kvlpat42e+TGVAGiZAUOtS4jHGE1RqfXp13G lDdiLKVpReuHpVVtvgTuMSvJzLRV/6zJ/+XExzgZI9b2IIwgt7YVS5pPzYCykm2h YMuC7v4e+0epKxuwbGApzPbCquBJvoBq+aTqU4ZMltpENkEHKlm+9gotNeMBaWA9 xMETydcWCjEIqjDHdC1yWrGTlIHSE92KAM7pHASoCuddPmhaHIh/BuTDxfeJBrNn xUuukR1IVzgXZItiQ/Oz/QMNLI+EBpyBZyfb9LM3wiw0jf10+XyLE9zbMZhIc2Y2 hwuBQ1is/dkdBcWLhaSsjHQIpKwY3iYXXjQ/AToXZV4OS8MlTNL49eSlugEisObD AamLQa2JAvw1wzUDe/vj15hbV2dW5bg43qVcTRJpAtg45FnPHynyJo34z7vqYNcb M1ljZtv+LRQeM3d4EHosrDKhhxlcOiUmUxl9E7dFlmutsusz/zW1/kbNebSj0WJt Ssb3lDO4JTNCI1RLb5I6Soe29FukeKmq/RYwlT49ZmRWxhpU6mE= =ThZf -----END PGP SIGNATURE----- Merge tag 'perf_urgent_for_v6.14_rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull x86 perf fixes from Borislav Petkov: - Explicitly clear DEBUGCTL.LBR to prevent LBRs continuing being enabled after handoff to the OS - Check CPUID(0x23) leaf and subleafs presence properly - Remove the PEBS-via-PT feature from being supported on hybrid systems - Fix perf record/top default commands on systems without a raw PMU registered * tag 'perf_urgent_for_v6.14_rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: perf/x86/intel: Ensure LBRs are disabled when a CPU is starting perf/x86/intel: Fix ARCH_PERFMON_NUM_COUNTER_LEAF perf/x86/intel: Clean up PEBS-via-PT on hybrid perf/x86/rapl: Fix the error checking order |
||
|
Linus Torvalds
|
ff3b373ecc |
- Clarify what happens when a task is woken up from the wake queue and make
clear its removal from that queue is atomic -----BEGIN PGP SIGNATURE----- iQIzBAABCgAdFiEEzv7L6UO9uDPlPSfHEsHwGGHeVUoFAmexq1MACgkQEsHwGGHe VUq6ghAAoD872KGmQ3YioDZs+FKLpLWvo+6lC2rY+GFQ3oCu4TJfmlsiTGLCyzjv aYwL52diIORD9/Yfn6Sq/ZWkfncoVmwnht+tgVjXeRr3Pb4EnttgWxPRx/xYQizr jgRASpNsRUTr6zNzqEeeQYodIJaInOF5+r26oqYArcN5V9XB9Qaj0+f14UiyB6u+ 53qpEQqQopeLPyG4t59iUfefsaWm2ZIW3EnoWeyI8sRuaapGY/0LHhUAn6vcA++N kuUkliVsk+f/uTNZeJ4zv2uy8DpBXO4kTjmwPVwFz46sJ8RL8P7MOLax7e7fNssw tylwHt4qoLEoB2vg1yMvlUNFMeH85gj8hTyJMsgGtFTbwCH0kLFEoXUz0lfKMS7U A271E1Bumu3OT7FrAnxQahViv02YWG5fcg6R3OidQdSmgoQBIMJwDA2pyKLiq9FL 7mWoNfEqqBWn4O/1qBlf3jCvfFlzXRSSgVzEruoNB93cgzTaQaN5yVgeekMzwJEj NDowmIZRxEN8+lJyMxIGSOGa44aTXu0/+dtehEDeSpsDOXULFc5fpYt4SSa0Jt/F LlgnPGkM1vF0ddG5vDJpGw6B9Dhb82i1oYy2IVwOCkLOXSp2kvLDEI3sqgk5mmlH zFtAV21Zm4jqBke/aF7r+RCYRvDyQkuW0d1+H9okGWLSk7jKauM= =J43o -----END PGP SIGNATURE----- Merge tag 'sched_urgent_for_v6.14_rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull scheduler fix from Borislav Petkov: - Clarify what happens when a task is woken up from the wake queue and make clear its removal from that queue is atomic * tag 'sched_urgent_for_v6.14_rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: sched: Clarify wake_up_q()'s write to task->wake_q.next |
||
|
Linus Torvalds
|
592c358ea9 |
- Move a warning about a lld.ld breakage into the verbose setting as said
breakage has been fixed in the meantime - Teach objtool to ignore dangling jump table entries added by Clang -----BEGIN PGP SIGNATURE----- iQIzBAABCgAdFiEEzv7L6UO9uDPlPSfHEsHwGGHeVUoFAmexqKkACgkQEsHwGGHe VUpaaw/+Pl6iTpZMXmL3uygZpgWR2QgBHIKcwFF9RcVpRDQ19PlSfSpmb2PL2jOf aKoAWq7MiVo2+yMguXYUj4vn8c+I0bBEQvlseUsYzVOiW3RBK1y39K1HZxCX6r3T y/kpXix25Bjs323cxS73U5gmoW6Wpqi/gFVBljXrLlugtqgXJhUXWCpVTL8lkzuH jLkc9pGGt7UAnOWBsKy3FQNZVy4lz6KC9nlYc6dSbAE5dmldBujBVtr9R8GfNxhe K7L5kiKk50rQmlYfZ8aS2ExG+W4EzInU5QHVS6DMsyEU5a3PS/WxYLFQOibjbcM7 7b8SccJGyNsZLaseNMk2Eud5FDcdGFNH2/wFd/hpVxq5Mrfh2iyG9ADzqtWMFz/6 xt0cc4C56v3tS+m1ticahjkB5l/DlvqLe/N2EVNR+15lIdxoTfeRZSoJlo/o1liu G/nZxDQssr57vmALal6b5js6XRrHqsCQVAN9Y9k6TMPcFYbq4B7YHyTe4Q12ChIg BRu/FJJFNjiC6c7QvJ7U/QNpDT3OPrI5Bp4BRGt+Yn7aujtnxUIAgI5+caEe+ASQ 8DEeLwzfMqUTVSeiUeAPrjN9ep0qox7051GqCsQflJqZ7FH321lhrps66kfkDKR8 3c6hr2SyzLzRsBNnTSliVV9OJHrQS/0psQwyuvIEN6mEh/EAk0A= =fVLM -----END PGP SIGNATURE----- Merge tag 'objtool_urgent_for_v6.14_rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull objtool fixes from Borislav Petkov: - Move a warning about a lld.ld breakage into the verbose setting as said breakage has been fixed in the meantime - Teach objtool to ignore dangling jump table entries added by Clang * tag 'objtool_urgent_for_v6.14_rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: objtool: Move dodgy linker warn to verbose objtool: Ignore dangling jump table entries |
||
|
Linus Torvalds
|
82ff316456 |
ARM:
- Large set of fixes for vector handling, specially in the interactions
between host and guest state. This fixes a number of bugs affecting
actual deployments, and greatly simplifies the FP/SIMD/SVE handling.
Thanks to Mark Rutland for dealing with this thankless task.
- Fix an ugly race between vcpu and vgic creation/init, resulting in
unexpected behaviours.
- Fix use of kernel VAs at EL2 when emulating timers with nVHE.
- Small set of pKVM improvements and cleanups.
x86:
- Fix broken SNP support with KVM module built-in, ensuring the PSP
module is initialized before KVM even when the module infrastructure
cannot be used to order initcalls
- Reject Hyper-V SEND_IPI hypercalls if the local APIC isn't being emulated
by KVM to fix a NULL pointer dereference.
- Enter guest mode (L2) from KVM's perspective before initializing the vCPU's
nested NPT MMU so that the MMU is properly tagged for L2, not L1.
- Load the guest's DR6 outside of the innermost .vcpu_run() loop, as the
guest's value may be stale if a VM-Exit is handled in the fastpath.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmev2ykUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroMvxwf/bw2u08moAYWAjJLROFvfiKXnznLS
iqJ2+jcw0lJ7wDqm4Zw8M5t74Rd+y5yzkLkZOyjav9yBB09zRkItiTHljCNMOQnt
2QptBa3CUN8N+rNnvVRt6dMkhw7z6n7eoFRSIDY2Y9PgiTapbFXPV1gFkMPO6+0f
SyF4LCr0iuDkJdvGAZJAH/Mp8nG6dv/A6a+Q+R1RkbKn9c2OdWw4VMfhIzimFGN6
0RFjbfXXvyO0aU/W/VHwvvuhcjGkAZWfHDdaTXqbvSMhayW562UPVMVBwXdVBmDj
Dk1gCKcbm4WyktbXYW6iOYj3MgdK96eI24ozps4R0aDexsrTRY4IfH4KEg==
=20Ql
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"ARM:
- Large set of fixes for vector handling, especially in the
interactions between host and guest state.
This fixes a number of bugs affecting actual deployments, and
greatly simplifies the FP/SIMD/SVE handling. Thanks to Mark Rutland
for dealing with this thankless task.
- Fix an ugly race between vcpu and vgic creation/init, resulting in
unexpected behaviours
- Fix use of kernel VAs at EL2 when emulating timers with nVHE
- Small set of pKVM improvements and cleanups
x86:
- Fix broken SNP support with KVM module built-in, ensuring the PSP
module is initialized before KVM even when the module
infrastructure cannot be used to order initcalls
- Reject Hyper-V SEND_IPI hypercalls if the local APIC isn't being
emulated by KVM to fix a NULL pointer dereference
- Enter guest mode (L2) from KVM's perspective before initializing
the vCPU's nested NPT MMU so that the MMU is properly tagged for
L2, not L1
- Load the guest's DR6 outside of the innermost .vcpu_run() loop, as
the guest's value may be stale if a VM-Exit is handled in the
fastpath"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (25 commits)
x86/sev: Fix broken SNP support with KVM module built-in
KVM: SVM: Ensure PSP module is initialized if KVM module is built-in
crypto: ccp: Add external API interface for PSP module initialization
KVM: arm64: vgic: Hoist SGI/PPI alloc from vgic_init() to kvm_create_vgic()
KVM: arm64: timer: Drop warning on failed interrupt signalling
KVM: arm64: Fix alignment of kvm_hyp_memcache allocations
KVM: arm64: Convert timer offset VA when accessed in HYP code
KVM: arm64: Simplify warning in kvm_arch_vcpu_load_fp()
KVM: arm64: Eagerly switch ZCR_EL{1,2}
KVM: arm64: Mark some header functions as inline
KVM: arm64: Refactor exit handlers
KVM: arm64: Refactor CPTR trap deactivation
KVM: arm64: Remove VHE host restore of CPACR_EL1.SMEN
KVM: arm64: Remove VHE host restore of CPACR_EL1.ZEN
KVM: arm64: Remove host FPSIMD saving for non-protected KVM
KVM: arm64: Unconditionally save+flush host FPSIMD/SVE/SME state
KVM: x86: Load DR6 with guest value only before entering .vcpu_run() loop
KVM: nSVM: Enter guest mode before initializing nested NPT MMU
KVM: selftests: Add CPUID tests for Hyper-V features that need in-kernel APIC
KVM: selftests: Manage CPUID array in Hyper-V CPUID test's core helper
...
|
||
|
Linus Torvalds
|
b878a1c072 |
Fix for o32 ptrace/get_syscall_info
-----BEGIN PGP SIGNATURE----- iQJOBAABCAA4FiEEbt46xwy6kEcDOXoUeZbBVTGwZHAFAmexsT4aHHRzYm9nZW5k QGFscGhhLmZyYW5rZW4uZGUACgkQeZbBVTGwZHAnxRAApYw6GxstHfD83VFsdPwR E3OQlURzGsI8iWp4g/J/e6iC4tUB2pag8RrEYT0kWW2Q9f6LIVgLys3h9mndlM+0 OX1nCTzz4AJ/3bHoXp00ptrdm1MPUuV8lcZGYpB+atig5IjH+4BHeG3Vq1Nr581b y1zy/fIvd47JaJU6S4H30VL+djUXzNUezzNMmcJyO6s790uOMjcvDZgkocfkVVA1 AE1SQ7RDg98GDBn7HaN0SxsWknhZAy0cq00byuRCnqJcnWP+bqUFJzqdhqgiJnG9 PrAiP4XzkThk/I2gBufo/Vtx8UA8x2XCGVqBFlf+8GQIc4IUaM93gU4Y1EBZRViK 3MHFBM8QSA9wl7ZmlfxTQZVGISeIs9jHcL+Ejt3NeJ8tYbDneF5zL0I6uygmGuwI CgK9bN1UDP0MWm+5TyFd3cq0GnxPdhebbK3x/F3pZCfLfjelqanMLrIQIqHqoUUT KrXqOacTeCiFskTliKknipueHBvSXcX+9k8Y+kEWxwQmi1JPxHTYGMDxRVxw1b8S rblwXgY6rK4UeQzY0FGJ1siBOa22lcc3sqRNoq1SIRqUuH8Uq5jSO1frm2YflNWi gGxWwV61c6J4c4o4zCWQe9i6f4ZNokroWkt1Zfwhih/TZzAXQPMKcFArF/Txgz4Z K1E+SEt8fA2BiuKXa1iSqZY= =DHeR -----END PGP SIGNATURE----- Merge tag 'mips-fixes_6.14_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux Pull MIPS fixes from Thomas Bogendoerfer: "Fix for o32 ptrace/get_syscall_info" * tag 'mips-fixes_6.14_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: MIPS: fix mips_get_syscall_arg() for o32 MIPS: Export syscall stack arguments properly for remote use |
||
|
Linus Torvalds
|
ad1b832bf1 |
Devicetree fixes for v6.14:
- Add bindings for QCom QCS8300 clocks, QCom SAR2130P qfprom,
powertip,{st7272|hx8238a} displays,
- Fix compatible for TI am62a7 dss
- Add a kunit test for __of_address_resource_bounds()
-----BEGIN PGP SIGNATURE-----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=gmty
-----END PGP SIGNATURE-----
Merge tag 'devicetree-fixes-for-6.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree fixes from Rob Herring:
- Add bindings for QCom QCS8300 clocks, QCom SAR2130P qfprom, and
powertip,{st7272|hx8238a} displays
- Fix compatible for TI am62a7 dss
- Add a kunit test for __of_address_resource_bounds()
* tag 'devicetree-fixes-for-6.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: display: Add powertip,{st7272|hx8238a} as DT Schema description
dt-bindings: nvmem: qcom,qfprom: Add SAR2130P compatible
dt-bindings: display: ti: Fix compatible for am62a7 dss
of: address: Add kunit test for __of_address_resource_bounds()
dt-bindings: clock: qcom: Add QCS8300 video clock controller
dt-bindings: clock: qcom: Add CAMCC clocks for QCS8300
dt-bindings: clock: qcom: Add GPU clocks for QCS8300
|
||
|
Linus Torvalds
|
ad73b9a17d |
This pull request contains the following bug fixes for UML:
- Align signal stack correctly - Convert to raw spinlocks where needed (irq and virtio) - FPU related fixes -----BEGIN PGP SIGNATURE----- iQJKBAABCAA0FiEEdgfidid8lnn52cLTZvlZhesYu8EFAmexEa4WHHJpY2hhcmRA c2lnbWEtc3Rhci5hdAAKCRBm+VmF6xi7wZvCEACnL/iy1h/NX57a5UsRfP+dcpis skIJ+FHZdEErS60Mkqrw7qcOnSvOmLpq/8ZApJ2EFS6w+2XFGNw0Ev7vVSZJRXtM 1WHxcaY3O5qkkbvB8FzFKx9SEmzZg1m8ccofDxgIXJbPOEMpfcYIV4ZgmKtzHGZM GFwoaOIWceIGLBB8YfcGcNNojLpewAJJLZ47KehYvJARLAFYTv0zl5gzUXJWCxc0 7oMbBmshxo74sS62Qd1j818TyDa8hZApP8cC2eNKUX6UMjSqj5L2n40ovSkkVGcw YVovGS4RFYHW8gXIuwH3CpdqLm9rCfmZ2une6kgDSvKNw4bX+nuPvgewBa2QwuWa 9nQlpwFipFoUhfR9Sq+tDZnEGy2vUGfPMJMz2gqMI9yBp5kpFUyt1T/eFxasKs9T ge7nkwHkqovxgtqQ26S5US+uDS450yH2Ga+xRHJXyeNenkeJMrTP2xCR7cjmMsjP y5E0s6XtHPRQ4JFfUqI2btesmAAdMEAyhxdwASd0zvJVf/Q+VCzwWGYgij+s5f5e 3Zqaw1qaVIikDXnlOMpPWcmekMCBhIpi7joYz+BHSeBNjK756i0/YkHDMHDH2PBH AbOPakddGfWSZzHnuNwQWr47L6/rJQl/vAmjtLYwW7Ped70zXoIeiQMkkHyfSTuO 73Fl6RH/W8Q/XJb9pA== =5mdK -----END PGP SIGNATURE----- Merge tag 'uml-for-linus-6.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/uml/linux Pull UML fixes from Richard Weinberger: - Align signal stack correctly - Convert to raw spinlocks where needed (irq and virtio) - FPU related fixes * tag 'uml-for-linus-6.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/uml/linux: um: convert irq_lock to raw spinlock um: virtio_uml: use raw spinlock um: virt-pci: don't use kmalloc() um: fix execve stub execution on old host OSs um: properly align signal stack on x86_64 um: avoid copying FP state from init_task um: add back support for FXSAVE registers |
||
|
Linus Torvalds
|
5784d8c93e |
Ring buffer fixes for v6.14:
- Enable resize on mmap() error When a process mmaps a ring buffer, its size is locked and resizing is disabled. But if the user passes in a wrong parameter, the mmap() can fail after the resize was disabled and the mmap() exits with error without reenabling the ring buffer resize. This prevents the ring buffer from ever being resized after that. Reenable resizing of the ring buffer on mmap() error. - Have resizing return proper error and not always -ENOMEM If the ring buffer is mmapped by one task and another task tries to resize the buffer it will error with -ENOMEM. This is confusing to the user as there may be plenty of memory available. Have it return the error that actually happens (in this case -EBUSY) where the user can understand why the resize failed. - Test the sub-buffer array to validate persistent memory buffer On boot up, the initialization of the persistent memory buffer will do a validation check to see if the content of the data is valid, and if so, it will use the memory as is, otherwise it re-initializes it. There's meta data in this persistent memory that keeps track of which sub-buffer is the reader page and an array that states the order of the sub-buffers. The values in this array are indexes into the sub-buffers. The validator checks to make sure that all the entries in the array are within the sub-buffer list index, but it does not check for duplications. While working on this code, the array got corrupted and had duplicates, where not all the sub-buffers were accounted for. This passed the validator as all entries were valid, but the link list was incorrect and could have caused a crash. The corruption only produced incorrect data, but it could have been more severe. To fix this, create a bitmask that covers all the sub-buffer indexes and set it to all zeros. While iterating the array checking the values of the array content, have it set a bit corresponding to the index in the array. If the bit was already set, then it is a duplicate and mark the buffer as invalid and reset it. - Prevent mmap()ing persistent ring buffer The persistent ring buffer uses vmap() to map the persistent memory. Currently, the mmap() logic only uses virt_to_page() to get the page from the ring buffer memory and use that to map to user space. This works because a normal ring buffer uses alloc_page() to allocate its memory. But because the persistent ring buffer use vmap() it causes a kernel crash. Fixing this to work with vmap() is not hard, but since mmap() on persistent memory buffers never worked, just have the mmap() return -ENODEV (what was returned before mmap() for persistent memory ring buffers, as they never supported mmap. Normal buffers will still allow mmap(). Implementing mmap() for persistent memory ring buffers can wait till the next merge window. - Fix polling on persistent ring buffers There's a "buffer_percent" option (default set to 50), that is used to have reads of the ring buffer binary data block until the buffer fills to that percentage. The field "pages_touched" is incremented every time a new sub-buffer has content added to it. This field is used in the calculations to determine the amount of content is in the buffer and if it exceeds the "buffer_percent" then it will wake the task polling on the buffer. As persistent ring buffers can be created by the content from a previous boot, the "pages_touched" field was not updated. This means that if a task were to poll on the persistent buffer, it would block even if the buffer was completely full. It would block even if the "buffer_percent" was zero, because with "pages_touched" as zero, it would be calculated as the buffer having no content. Update pages_touched when initializing the persistent ring buffer from a previous boot. -----BEGIN PGP SIGNATURE----- iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCZ7DtcxQccm9zdGVkdEBn b29kbWlzLm9yZwAKCRAp5XQQmuv6qmTQAQD1W/xHfS8yLw7BQBjM+6kqExdrKI/D Z378Et0LSWjZBQD/VtPKiSjLhhNgLUBy5fAWS5t4X/DZ49GKhTA36AzGHwE= =1b+2 -----END PGP SIGNATURE----- Merge tag 'trace-ring-buffer-v6.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace Pull trace ring buffer fixes from Steven Rostedt: - Enable resize on mmap() error When a process mmaps a ring buffer, its size is locked and resizing is disabled. But if the user passes in a wrong parameter, the mmap() can fail after the resize was disabled and the mmap() exits with error without reenabling the ring buffer resize. This prevents the ring buffer from ever being resized after that. Reenable resizing of the ring buffer on mmap() error. - Have resizing return proper error and not always -ENOMEM If the ring buffer is mmapped by one task and another task tries to resize the buffer it will error with -ENOMEM. This is confusing to the user as there may be plenty of memory available. Have it return the error that actually happens (in this case -EBUSY) where the user can understand why the resize failed. - Test the sub-buffer array to validate persistent memory buffer On boot up, the initialization of the persistent memory buffer will do a validation check to see if the content of the data is valid, and if so, it will use the memory as is, otherwise it re-initializes it. There's meta data in this persistent memory that keeps track of which sub-buffer is the reader page and an array that states the order of the sub-buffers. The values in this array are indexes into the sub-buffers. The validator checks to make sure that all the entries in the array are within the sub-buffer list index, but it does not check for duplications. While working on this code, the array got corrupted and had duplicates, where not all the sub-buffers were accounted for. This passed the validator as all entries were valid, but the link list was incorrect and could have caused a crash. The corruption only produced incorrect data, but it could have been more severe. To fix this, create a bitmask that covers all the sub-buffer indexes and set it to all zeros. While iterating the array checking the values of the array content, have it set a bit corresponding to the index in the array. If the bit was already set, then it is a duplicate and mark the buffer as invalid and reset it. - Prevent mmap()ing persistent ring buffer The persistent ring buffer uses vmap() to map the persistent memory. Currently, the mmap() logic only uses virt_to_page() to get the page from the ring buffer memory and use that to map to user space. This works because a normal ring buffer uses alloc_page() to allocate its memory. But because the persistent ring buffer use vmap() it causes a kernel crash. Fixing this to work with vmap() is not hard, but since mmap() on persistent memory buffers never worked, just have the mmap() return -ENODEV (what was returned before mmap() for persistent memory ring buffers, as they never supported mmap. Normal buffers will still allow mmap(). Implementing mmap() for persistent memory ring buffers can wait till the next merge window. - Fix polling on persistent ring buffers There's a "buffer_percent" option (default set to 50), that is used to have reads of the ring buffer binary data block until the buffer fills to that percentage. The field "pages_touched" is incremented every time a new sub-buffer has content added to it. This field is used in the calculations to determine the amount of content is in the buffer and if it exceeds the "buffer_percent" then it will wake the task polling on the buffer. As persistent ring buffers can be created by the content from a previous boot, the "pages_touched" field was not updated. This means that if a task were to poll on the persistent buffer, it would block even if the buffer was completely full. It would block even if the "buffer_percent" was zero, because with "pages_touched" as zero, it would be calculated as the buffer having no content. Update pages_touched when initializing the persistent ring buffer from a previous boot. * tag 'trace-ring-buffer-v6.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace: ring-buffer: Update pages_touched to reflect persistent buffer content tracing: Do not allow mmap() of persistent ring buffer ring-buffer: Validate the persistent meta data subbuf array tracing: Have the error of __tracing_resize_ring_buffer() passed to user ring-buffer: Unlock resize on mmap error |
||
|
Steven Rostedt
|
97937834ae |
ring-buffer: Update pages_touched to reflect persistent buffer content
The pages_touched field represents the number of subbuffers in the ring
buffer that have content that can be read. This is used in accounting of
"dirty_pages" and "buffer_percent" to allow the user to wait for the
buffer to be filled to a certain amount before it reads the buffer in
blocking mode.
The persistent buffer never updated this value so it was set to zero, and
this accounting would take it as it had no content. This would cause user
space to wait for content even though there's enough content in the ring
buffer that satisfies the buffer_percent.
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Vincent Donnefort <vdonnefort@google.com>
Link: https://lore.kernel.org/20250214123512.0631436e@gandalf.local.home
Fixes:
|
||
|
Steven Rostedt
|
129fe71881 |
tracing: Do not allow mmap() of persistent ring buffer
When trying to mmap a trace instance buffer that is attached to
reserve_mem, it would crash:
BUG: unable to handle page fault for address: ffffe97bd00025c8
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 2862f3067 P4D 2862f3067 PUD 0
Oops: Oops: 0000 [#1] PREEMPT_RT SMP PTI
CPU: 4 UID: 0 PID: 981 Comm: mmap-rb Not tainted 6.14.0-rc2-test-00003-g7f1a5e3fbf9e-dirty #233
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2 04/01/2014
RIP: 0010:validate_page_before_insert+0x5/0xb0
Code: e2 01 89 d0 c3 cc cc cc cc 66 66 2e 0f 1f 84 00 00 00 00 00 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 0f 1f 44 00 00 <48> 8b 46 08 a8 01 75 67 66 90 48 89 f0 8b 50 34 85 d2 74 76 48 89
RSP: 0018:ffffb148c2f3f968 EFLAGS: 00010246
RAX: ffff9fa5d3322000 RBX: ffff9fa5ccff9c08 RCX: 00000000b879ed29
RDX: ffffe97bd00025c0 RSI: ffffe97bd00025c0 RDI: ffff9fa5ccff9c08
RBP: ffffb148c2f3f9f0 R08: 0000000000000004 R09: 0000000000000004
R10: 0000000000000000 R11: 0000000000000200 R12: 0000000000000000
R13: 00007f16a18d5000 R14: ffff9fa5c48db6a8 R15: 0000000000000000
FS: 00007f16a1b54740(0000) GS:ffff9fa73df00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffffe97bd00025c8 CR3: 00000001048c6006 CR4: 0000000000172ef0
Call Trace:
<TASK>
? __die_body.cold+0x19/0x1f
? __die+0x2e/0x40
? page_fault_oops+0x157/0x2b0
? search_module_extables+0x53/0x80
? validate_page_before_insert+0x5/0xb0
? kernelmode_fixup_or_oops.isra.0+0x5f/0x70
? __bad_area_nosemaphore+0x16e/0x1b0
? bad_area_nosemaphore+0x16/0x20
? do_kern_addr_fault+0x77/0x90
? exc_page_fault+0x22b/0x230
? asm_exc_page_fault+0x2b/0x30
? validate_page_before_insert+0x5/0xb0
? vm_insert_pages+0x151/0x400
__rb_map_vma+0x21f/0x3f0
ring_buffer_map+0x21b/0x2f0
tracing_buffers_mmap+0x70/0xd0
__mmap_region+0x6f0/0xbd0
mmap_region+0x7f/0x130
do_mmap+0x475/0x610
vm_mmap_pgoff+0xf2/0x1d0
ksys_mmap_pgoff+0x166/0x200
__x64_sys_mmap+0x37/0x50
x64_sys_call+0x1670/0x1d70
do_syscall_64+0xbb/0x1d0
entry_SYSCALL_64_after_hwframe+0x77/0x7f
The reason was that the code that maps the ring buffer pages to user space
has:
page = virt_to_page((void *)cpu_buffer->subbuf_ids[s]);
And uses that in:
vm_insert_pages(vma, vma->vm_start, pages, &nr_pages);
But virt_to_page() does not work with vmap()'d memory which is what the
persistent ring buffer has. It is rather trivial to allow this, but for
now just disable mmap() of instances that have their ring buffer from the
reserve_mem option.
If an mmap() is performed on a persistent buffer it will return -ENODEV
just like it would if the .mmap field wasn't defined in the
file_operations structure.
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Vincent Donnefort <vdonnefort@google.com>
Link: https://lore.kernel.org/20250214115547.0d7287d3@gandalf.local.home
Fixes:
|
||
|
Linus Torvalds
|
496659003d |
i2c-for-6.14-rc3
MAINTAINERS maintenance. Changed email, added entry, deleted entry falling back to a generic one. -----BEGIN PGP SIGNATURE----- iQIzBAABCgAdFiEEOZGx6rniZ1Gk92RdFA3kzBSgKbYFAmewyegACgkQFA3kzBSg KbYxmBAAlos2INsA+kvuEkvaQ0eXx+T3yEOVyHrwY2Ls41Ze2laR0jI/uWq7Icmn /WeQZKnwgmNc+mlp90AEGf+gVGyvh0VrPAWHTvjtlLNHSzQOP12GcTRg10Z03WGo 0y31c3P3D3GyeO/boVeAe2DuN5m6eT4nntamtdQQcfjpMdWmHKQ8pWvYGBZbSFFn 9YeXE6q0/6zeg3xu7X9CSD1R+szdNfQnilF3VdSVyFdOwHQjZdimFus7UCSilYcV pbARGAC+oz8oZRzLPP1X3j1keFwZM7+L6iVdkIhuh3GhCeEGVVZircvxBIUO9o4J aM4hxZVDZlpZlsMZ3PGBOPQl3ZYRWcoskUx+7gxx7iSIc0p+MD/0IF6EqX3i8eqC 19x+HGi8Evjf1+/NC2ouOGVGMKYc7i0Bf/vCCDBE6X7f4QDZHm2ebQpCU9HsFaJv NPvIM262OuoIigqnDA6Oq/XfD/2fIPLHDgs7f0Vj5WFG4FnRQMn5iBiwJ5qzHtcY T2di9vX6feBJJo9dJ3HcdT1aJMi/H7JHcwd3M2FDE6x5rj5sxWNNKq6xnp2YqlB/ 41p3LYk6dS8F4CcbINqxGJNYat0EIRls/sTiX2Jvw9GewT7HlZc22OuLYK7jR7fe OCD7QMnrRHqneNSmPUet5Y0m4vddxcbUq0pPyGRBls2MoB4lJg8= =cNCH -----END PGP SIGNATURE----- Merge tag 'i2c-for-6.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux Pull i2c fixes from Wolfram Sang: "MAINTAINERS maintenance. Changed email, added entry, deleted entry falling back to a generic one" * tag 'i2c-for-6.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: MAINTAINERS: Add maintainer for Qualcomm's I2C GENI driver MAINTAINERS: delete entry for AXXIA I2C MAINTAINERS: Use my kernel.org address for I2C ACPI work |
||
|
Linus Torvalds
|
f3d8b0ebae |
s390 updates for 6.14-rc3
- Fix isolated VFs handling by verifying that a VF’s parent PF is locally owned before registering it in an existing PCI domain - Disable arch_test_bit() optimization for PROFILE_ALL_BRANCHES to workaround gcc failure in handling __builtin_constant_p() in this case - Fix CHPID "configure" attribute caching in CIO by not updating the cache when SCLP returns no data, ensuring consistent sysfs output - Remove CONFIG_LSM from default configs and rely on defaults, which enables BPF LSM hook -----BEGIN PGP SIGNATURE----- iQEzBAABCAAdFiEE3QHqV+H2a8xAv27vjYWKoQLXFBgFAmewxaoACgkQjYWKoQLX FBiQAQf/XfD1/DV91nLpGUsV4lrFEbksiptaaVRLkYQmrlvW1jPSTt4u/789jgTW oaFccUL5sPrzFInC5Mv6x1MUH90p3i31PZ4b6+AwiDWFAJbFPj2//CAA8hl2Uci3 ES45/GEQaYCqKXt05l19plapkfONYFnFwM+dI98lAzZAfz7X9g7OxZLaBTbGojSl 1wt3gEta7aFGrJtYUhpKrcDOnxBDWqCOB4h/bL8RzEQ7sAjR1dYJBE7cQIGq3aW/ o9cMYQRRSzPmLVoO8dF/xswHKpU3+ms8peGcoqoaq9oll2oduJp8zijy4JFgVjCE P5HMfDv4i8p+TrqEuvKtMYQC0MhOlA== =mCvM -----END PGP SIGNATURE----- Merge tag 's390-6.14-4' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux Pull s390 fixes from Vasily Gorbik: - Fix isolated VFs handling by verifying that a VF’s parent PF is locally owned before registering it in an existing PCI domain - Disable arch_test_bit() optimization for PROFILE_ALL_BRANCHES to workaround gcc failure in handling __builtin_constant_p() in this case - Fix CHPID "configure" attribute caching in CIO by not updating the cache when SCLP returns no data, ensuring consistent sysfs output - Remove CONFIG_LSM from default configs and rely on defaults, which enables BPF LSM hook * tag 's390-6.14-4' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: s390/pci: Fix handling of isolated VFs s390/pci: Pull search for parent PF out of zpci_iov_setup_virtfn() s390/bitops: Disable arch_test_bit() optimization for PROFILE_ALL_BRANCHES s390/cio: Fix CHPID "configure" attribute caching s390/configs: Remove CONFIG_LSM |
||
|
Uwe Kleine-König
|
b28fb1f2ef |
modpost: Fix a few typos in a comment
Namely: s/becasue/because/ and s/wiht/with/ plus an added article. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com> Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> |
||
|
Thomas Weißschuh
|
1b71c2fb04 |
kbuild: userprogs: fix bitsize and target detection on clang
scripts/Makefile.clang was changed in the linked commit to move --target from
KBUILD_CFLAGS to KBUILD_CPPFLAGS, as that generally has a broader scope.
However that variable is not inspected by the userprogs logic,
breaking cross compilation on clang.
Use both variables to detect bitsize and target arguments for userprogs.
Fixes:
|
||
|
Linus Torvalds
|
243899076c |
Rust fixes for v6.14 (2nd)
Toolchain and infrastructure:
- Fix objtool warning due to future Rust 1.85.0 (to be released in
a few days).
- Clean future Rust 1.86.0 (to be released 2025-04-03) Clippy warning.
-----BEGIN PGP SIGNATURE-----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=98Tv
-----END PGP SIGNATURE-----
Merge tag 'rust-fixes-6.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ojeda/linux
Pull rust fixes from Miguel Ojeda:
- Fix objtool warning due to future Rust 1.85.0 (to be released in a
few days)
- Clean future Rust 1.86.0 (to be released 2025-04-03) Clippy warning
* tag 'rust-fixes-6.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ojeda/linux:
rust: rbtree: fix overindented list item
objtool/rust: add one more `noreturn` Rust function
|
||
|
Linus Torvalds
|
d440148418 |
tegra210-adma: fix 32-bit x86 build
The Tegra210 Audio DMA controller driver did a plain divide: page_no = (res_page->start - res_base->start) / cdata->ch_base_offset; which causes problems on 32-bit x86 configurations that have 64-bit resource sizes: x86_64-linux-ld: drivers/dma/tegra210-adma.o: in function `tegra_adma_probe': tegra210-adma.c:(.text+0x1322): undefined reference to `__udivdi3' because gcc doesn't generate the trivial code for a 64-by-32 divide, turning it into a function call to do a full 64-by-64 divide. And the kernel intentionally doesn't provide that helper function, because 99% of the time all you want is the narrower version. Of course, tegra210 is a 64-bit architecture and the 32-bit x86 build is purely for build testing, so this really is just about build coverage failure. But build coverage is good. Side note: div_u64() would be suboptimal if you actually have a 32-bit resource_t, so our "helper" for divides are admittedly making it harder than it should be to generate good code for all the possible cases. At some point, I'll consider 32-bit x86 so entirely legacy that I can't find it in myself to care any more, and we'll just add the __udivdi3 library function. But for now, the right thing to do is to use "div_u64()" to show that you know that you are doing the simpler divide with a 32-bit number. And the build error enforces that. While fixing the build issue, also check for division-by-zero, and for overflow. Which hopefully cannot happen on real production hardware, but the value of 'ch_base_offset' can definitely be zero in other places. Reported-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> |
||
|
Linus Torvalds
|
6452feaf29 |
gpio fixes for v6.14-rc3 - take 2
- fix interrupt handling issues in gpio-bcm-kona - add an ACPI quirk for Acer Nitro ANV14 fixing an issue with spurious wake up events - add missing return value checks to gpio-stmpe - fix a crash in error path in gpiochip_get_ngpios() -----BEGIN PGP SIGNATURE----- iQIzBAABCgAdFiEEFp3rbAvDxGAT0sefEacuoBRx13IFAmewXNIACgkQEacuoBRx 13L3aQ/8C2aQu4lqV2+eu+7PWAyrmwRkZ7qgLe33FFOHShgPLsK3du4iyccVy2Z4 Ett8Yk4hA/KbzlPPSKxK71su4b6dkVpyhZPLB5vwH8yebW+pRCk+FzFdGmcaeymX lg25pSdpIzezQMg/wmYmySu5CoeNbo8AkWQWwU8435URKec+Nmxh13Ssf8aQs5Fa cLTB4dhc7yuYll0F+J2VtJ8+m/Ryb17ic4204EQn0L4t+kgijaeIcUA4d26h3MMz WEHs911zP4tjXJUoaiTrMXp1oB16YzlHumppb7QzozZe1D6fLMjI/MeZbpkrJL5h NvgvsdBQMjLyZtK5EwA/7faExYfts4+g8TyzhF/7TEvz0omU7cLoN3V4/S4sUXa2 lCHufXc5864C1BcJ9tFQAZ1eS+hZiVDZPmCpZ08ACEcrfuzgvSEm5yyIOfALblFO VPsf6ic53XD9MEkAkLK+jMuqZOnifX9sYCvHVM4sgob+A8ra9kTo3XsMy1mHw/Da Z/ospRp/nRfG/hlT0Ko3mxsbmCPhKEEdC07ZVxjyiE0xtuMhMQyQpNtC6NkVLfg+ m21POmBcDZOH64wIOdWj15gTjy4im/p1KhHL5veXOJV36eEu7SiX699LYkNyu7px bVNoZqmMGVH9muD0rIAS1po2TWSDptHGsli2uL2ddQDfvOaelEU= =odVF -----END PGP SIGNATURE----- Merge tag 'gpio-fixes-for-v6.14-rc3-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux Pull gpio fixes from Bartosz Golaszewski: - fix interrupt handling issues in gpio-bcm-kona - add an ACPI quirk for Acer Nitro ANV14 fixing an issue with spurious wake up events - add missing return value checks to gpio-stmpe - fix a crash in error path in gpiochip_get_ngpios() * tag 'gpio-fixes-for-v6.14-rc3-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: gpiolib: Fix crash on error in gpiochip_get_ngpios() gpio: stmpe: Check return value of stmpe_reg_read in stmpe_gpio_irq_sync_unlock gpiolib: acpi: Add a quirk for Acer Nitro ANV14 gpio: bcm-kona: Add missing newline to dev_err format string gpio: bcm-kona: Make sure GPIO bits are unlocked when requesting IRQ gpio: bcm-kona: Fix GPIO lock/unlock for banks above bank 0 |
||
|
Masahiro Yamada
|
140332b6ed |
kbuild: fix linux-headers package build when $(CC) cannot link userspace
Since commit |
||
|
Masahiro Yamada
|
d1d0963121 |
tools: fix annoying "mkdir -p ..." logs when building tools in parallel
When CONFIG_OBJTOOL=y or CONFIG_DEBUG_INFO_BTF=y, parallel builds
show awkward "mkdir -p ..." logs.
$ make -j16
[ snip ]
mkdir -p /home/masahiro/ref/linux/tools/objtool && make O=/home/masahiro/ref/linux subdir=tools/objtool --no-print-directory -C objtool
mkdir -p /home/masahiro/ref/linux/tools/bpf/resolve_btfids && make O=/home/masahiro/ref/linux subdir=tools/bpf/resolve_btfids --no-print-directory -C bpf/resolve_btfids
Defining MAKEFLAGS=<value> on the command line wipes out command line
switches from the resultant MAKEFLAGS definition, even though the command
line switches are active. [1]
MAKEFLAGS puts all single-letter options into the first word, and that
word will be empty if no single-letter options were given. [2]
However, this breaks if MAKEFLAGS=<value> is given on the command line.
The tools/ and tools/% targets set MAKEFLAGS=<value> on the command
line, which breaks the following code in tools/scripts/Makefile.include:
short-opts := $(firstword -$(MAKEFLAGS))
If MAKEFLAGS really needs modification, it should be done through the
environment variable, as follows:
MAKEFLAGS=<value> $(MAKE) ...
That said, I question whether modifying MAKEFLAGS is necessary here.
The only flag we might want to exclude is --no-print-directory, as the
tools build system changes the working directory. However, people might
find the "Entering/Leaving directory" logs annoying.
I simply removed the offending MAKEFLAGS=<value>.
[1]: https://savannah.gnu.org/bugs/?62469
[2]: https://www.gnu.org/software/make/manual/make.html#Testing-Flags
Fixes:
|
||
|
Linus Torvalds
|
7ff71e6d92 |
alpha: Fixes for v6.14
Some important fixes for kernel stack alignment. -----BEGIN PGP SIGNATURE----- Version: GnuPG v2 iNUEABYKAH0WIQReryEEmoa4pUzLG/qs6yl0DJpOlwUCZ6+Vv18UgAAAAAAuAChp c3N1ZXItZnByQG5vdGF0aW9ucy5vcGVucGdwLmZpZnRoaG9yc2VtYW4ubmV0NUVB RjIxMDQ5QTg2QjhBNTRDQ0IxQkZBQUNFQjI5NzQwQzlBNEU5NwAKCRCs6yl0DJpO l4J2AP4iWkiWkpBvKOnA4vcutSaGiyIyJOoxHYUdF+4ZoJiKuQD/Uv8NesWE0w3g /JK/pBAXGOrIiD8fL34Vj74HvtyQtAk= =A3Fn -----END PGP SIGNATURE----- Merge tag 'alpha-fixes-v6.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha Pull alpha fixes from Matt Turner: "A few changes for alpha, including some important fixes for kernel stack alignment" * tag 'alpha-fixes-v6.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha: alpha: Use str_yes_no() helper in pci_dac_dma_supported() alpha: Replace one-element array with flexible array member alpha: align stack for page fault and user unaligned trap handlers alpha: make stack 16-byte aligned (most cases) alpha: replace hardcoded stack offsets with autogenerated ones |
||
|
Linus Torvalds
|
78a632a208 |
pci-v6.14-fixes-3
-----BEGIN PGP SIGNATURE----- iQJIBAABCgAyFiEEgMe7l+5h9hnxdsnuWYigwDrT+vwFAmev0oAUHGJoZWxnYWFz QGdvb2dsZS5jb20ACgkQWYigwDrT+vxeNBAAunByLPVxbteqIXJ6IZHz1956SDfo batHJodeNCxeVYpjLca+1asqZ75hply3pOK+DUKyNUyEqkXfQDvSZCBfo70uA9ur eSeaZxBoNS7VnOvmw5w0kEWd2Sx0gEkIPuxegympOfTiWaN8bGoryPHAuGnO0Exz YTIv+TtLAag96OFswQGvSZyh8AfCg5QXl6vZ0W7Ex+O24o/LJ9sO9gALkhFXoc2+ tdKBJSOQ3dfEVa0S6btNxsY5nsy7xp3CxLYqQTvT2kES0xUwK7QrafOdl0kEaVDB 6JRkFhKaK5R6WDz5d4LnU0mzSrBc17cQD+C6StUd4dzQdzyuiP4X70R+kMiu71ff XMSBPSbLcP1iQ50O3IdkbV5OVnn7ap3LPP2v/PYcmoYNc3i81hvZap5RDaEnJ/ej xI+bKullZG787jl+qnweNsu9jar9HWCJOGwMCZIKiXoU8fJdsI+b+53FNxFqqWAR 4DAsu9nGwlkoEFHaDFKeoG/qBrW65UAeIetUoh+dpQ19OaD7vUuv6Uk4aiwbDFx3 jGNBOS1Cwx3aIhLNrg3wxSmajFHaPlI+yElS+PcP/J9cV1YDXV7U/ZKaYTVwU0TZ l3TY72q3/ckP7+9NaxExO6ow59cN1XNncBkAcOEoSCfFIFnSmvxC8v6Vpwc2ZNQN o3N9euTROFouZeA= =HYty -----END PGP SIGNATURE----- Merge tag 'pci-v6.14-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci Pull pci fixes from Bjorn Helgaas: - Update a BUILD_BUG_ON() usage that works on current compilers, but breaks compilation on gcc 5.3.1 (Alex Williamson) - Avoid use of FLR for Mediatek MT7922 WiFi; the device previously worked after a long timeout and fallback to SBR, but after a recent RRS change it doesn't work at all after FLR (Bjorn Helgaas) * tag 'pci-v6.14-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: PCI: Avoid FLR for Mediatek MT7922 WiFi PCI: Fix BUILD_BUG_ON usage for old gcc |
||
|
Paolo Bonzini
|
d3d0b8dfe0 |
KVM fixes for 6.14 part 1
- Reject Hyper-V SEND_IPI hypercalls if the local APIC isn't being emulated
by KVM to fix a NULL pointer dereference.
- Enter guest mode (L2) from KVM's perspective before initializing the vCPU's
nested NPT MMU so that the MMU is properly tagged for L2, not L1.
- Load the guest's DR6 outside of the innermost .vcpu_run() loop, as the
guest's value may be stale if a VM-Exit is handled in the fastpath.
-----BEGIN PGP SIGNATURE-----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=aFcV
-----END PGP SIGNATURE-----
Merge tag 'kvm-x86-fixes-6.14-rcN' of https://github.com/kvm-x86/linux into HEAD
KVM fixes for 6.14 part 1
- Reject Hyper-V SEND_IPI hypercalls if the local APIC isn't being emulated
by KVM to fix a NULL pointer dereference.
- Enter guest mode (L2) from KVM's perspective before initializing the vCPU's
nested NPT MMU so that the MMU is properly tagged for L2, not L1.
- Load the guest's DR6 outside of the innermost .vcpu_run() loop, as the
guest's value may be stale if a VM-Exit is handled in the fastpath.
|
||
|
Ashish Kalra
|
409f45387c |
x86/sev: Fix broken SNP support with KVM module built-in
Fix issues with enabling SNP host support and effectively SNP support
which is broken with respect to the KVM module being built-in.
SNP host support is enabled in snp_rmptable_init() which is invoked as
device_initcall(). SNP check on IOMMU is done during IOMMU PCI init
(IOMMU_PCI_INIT stage). And for that reason snp_rmptable_init() is
currently invoked via device_initcall() and cannot be invoked via
subsys_initcall() as core IOMMU subsystem gets initialized via
subsys_initcall().
Now, if kvm_amd module is built-in, it gets initialized before SNP host
support is enabled in snp_rmptable_init() :
[ 10.131811] kvm_amd: TSC scaling supported
[ 10.136384] kvm_amd: Nested Virtualization enabled
[ 10.141734] kvm_amd: Nested Paging enabled
[ 10.146304] kvm_amd: LBR virtualization supported
[ 10.151557] kvm_amd: SEV enabled (ASIDs 100 - 509)
[ 10.156905] kvm_amd: SEV-ES enabled (ASIDs 1 - 99)
[ 10.162256] kvm_amd: SEV-SNP enabled (ASIDs 1 - 99)
[ 10.171508] kvm_amd: Virtual VMLOAD VMSAVE supported
[ 10.177052] kvm_amd: Virtual GIF supported
...
...
[ 10.201648] kvm_amd: in svm_enable_virtualization_cpu
And then svm_x86_ops->enable_virtualization_cpu()
(svm_enable_virtualization_cpu) programs MSR_VM_HSAVE_PA as following:
wrmsrl(MSR_VM_HSAVE_PA, sd->save_area_pa);
So VM_HSAVE_PA is non-zero before SNP support is enabled on all CPUs.
snp_rmptable_init() gets invoked after svm_enable_virtualization_cpu()
as following :
...
[ 11.256138] kvm_amd: in svm_enable_virtualization_cpu
...
[ 11.264918] SEV-SNP: in snp_rmptable_init
This triggers a #GP exception in snp_rmptable_init() when snp_enable()
is invoked to set SNP_EN in SYSCFG MSR:
[ 11.294289] unchecked MSR access error: WRMSR to 0xc0010010 (tried to write 0x0000000003fc0000) at rIP: 0xffffffffaf5d5c28 (native_write_msr+0x8/0x30)
...
[ 11.294404] Call Trace:
[ 11.294482] <IRQ>
[ 11.294513] ? show_stack_regs+0x26/0x30
[ 11.294522] ? ex_handler_msr+0x10f/0x180
[ 11.294529] ? search_extable+0x2b/0x40
[ 11.294538] ? fixup_exception+0x2dd/0x340
[ 11.294542] ? exc_general_protection+0x14f/0x440
[ 11.294550] ? asm_exc_general_protection+0x2b/0x30
[ 11.294557] ? __pfx_snp_enable+0x10/0x10
[ 11.294567] ? native_write_msr+0x8/0x30
[ 11.294570] ? __snp_enable+0x5d/0x70
[ 11.294575] snp_enable+0x19/0x20
[ 11.294578] __flush_smp_call_function_queue+0x9c/0x3a0
[ 11.294586] generic_smp_call_function_single_interrupt+0x17/0x20
[ 11.294589] __sysvec_call_function+0x20/0x90
[ 11.294596] sysvec_call_function+0x80/0xb0
[ 11.294601] </IRQ>
[ 11.294603] <TASK>
[ 11.294605] asm_sysvec_call_function+0x1f/0x30
...
[ 11.294631] arch_cpu_idle+0xd/0x20
[ 11.294633] default_idle_call+0x34/0xd0
[ 11.294636] do_idle+0x1f1/0x230
[ 11.294643] ? complete+0x71/0x80
[ 11.294649] cpu_startup_entry+0x30/0x40
[ 11.294652] start_secondary+0x12d/0x160
[ 11.294655] common_startup_64+0x13e/0x141
[ 11.294662] </TASK>
This #GP exception is getting triggered due to the following errata for
AMD family 19h Models 10h-1Fh Processors:
Processor may generate spurious #GP(0) Exception on WRMSR instruction:
Description:
The Processor will generate a spurious #GP(0) Exception on a WRMSR
instruction if the following conditions are all met:
- the target of the WRMSR is a SYSCFG register.
- the write changes the value of SYSCFG.SNPEn from 0 to 1.
- One of the threads that share the physical core has a non-zero
value in the VM_HSAVE_PA MSR.
The document being referred to above:
https://www.amd.com/content/dam/amd/en/documents/processor-tech-docs/revision-guides/57095-PUB_1_01.pdf
To summarize, with kvm_amd module being built-in, KVM/SVM initialization
happens before host SNP is enabled and this SVM initialization
sets VM_HSAVE_PA to non-zero, which then triggers a #GP when
SYSCFG.SNPEn is being set and this will subsequently cause
SNP_INIT(_EX) to fail with INVALID_CONFIG error as SYSCFG[SnpEn] is not
set on all CPUs.
Essentially SNP host enabling code should be invoked before KVM
initialization, which is currently not the case when KVM is built-in.
Add fix to call snp_rmptable_init() early from iommu_snp_enable()
directly and not invoked via device_initcall() which enables SNP host
support before KVM initialization with kvm_amd module built-in.
Add additional handling for `iommu=off` or `amd_iommu=off` options.
Note that IOMMUs need to be enabled for SNP initialization, therefore,
if host SNP support is enabled but late IOMMU initialization fails
then that will cause PSP driver's SNP_INIT to fail as IOMMU SNP sanity
checks in SNP firmware will fail with invalid configuration error as
below:
[ 9.723114] ccp 0000:23:00.1: sev enabled
[ 9.727602] ccp 0000:23:00.1: psp enabled
[ 9.732527] ccp 0000:a2:00.1: enabling device (0000 -> 0002)
[ 9.739098] ccp 0000:a2:00.1: no command queues available
[ 9.745167] ccp 0000:a2:00.1: psp enabled
[ 9.805337] ccp 0000:23:00.1: SEV-SNP: failed to INIT rc -5, error 0x3
[ 9.866426] ccp 0000:23:00.1: SEV API:1.53 build:5
Fixes:
|
||
|
Sean Christopherson
|
44e70718df |
KVM: SVM: Ensure PSP module is initialized if KVM module is built-in
The kernel's initcall infrastructure lacks the ability to express dependencies between initcalls, whereas the modules infrastructure automatically handles dependencies via symbol loading. Ensure the PSP SEV driver is initialized before proceeding in sev_hardware_setup() if KVM is built-in as the dependency isn't handled by the initcall infrastructure. Signed-off-by: Sean Christopherson <seanjc@google.com> Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: Ashish Kalra <ashish.kalra@amd.com> Message-ID: <f78ddb64087df27e7bcb1ae0ab53f55aa0804fab.1739226950.git.ashish.kalra@amd.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> |
||
|
Sean Christopherson
|
435b344a70 |
crypto: ccp: Add external API interface for PSP module initialization
KVM is dependent on the PSP SEV driver and PSP SEV driver needs to be loaded before KVM module. In case of module loading any dependent modules are automatically loaded but in case of built-in modules there is no inherent mechanism available to specify dependencies between modules and ensure that any dependent modules are loaded implicitly. Add a new external API interface for PSP module initialization which allows PSP SEV driver to be loaded explicitly if KVM is built-in. Signed-off-by: Sean Christopherson <seanjc@google.com> Co-developed-by: Ashish Kalra <ashish.kalra@amd.com> Signed-off-by: Ashish Kalra <ashish.kalra@amd.com> Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com> Message-ID: <15279ca0cad56a07cf12834ec544310f85ff5edc.1739226950.git.ashish.kalra@amd.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> |
||
|
Paolo Bonzini
|
3bb7dcebd0 |
KVM/arm64 fixes for 6.14, take #2
- Large set of fixes for vector handling, specially in the interactions between host and guest state. This fixes a number of bugs affecting actual deployments, and greatly simplifies the FP/SIMD/SVE handling. Thanks to Mark Rutland for dealing with this thankless task. - Fix an ugly race between vcpu and vgic creation/init, resulting in unexpected behaviours. - Fix use of kernel VAs at EL2 when emulating timers with nVHE. - Small set of pKVM improvements and cleanups. -----BEGIN PGP SIGNATURE----- iQIzBAABCgAdFiEEn9UcU+C1Yxj9lZw9I9DQutE9ekMFAmevLKMACgkQI9DQutE9 ekP3hQ//db7pAPzLr++//PAyam0GP+ooKlgpB0ImZisQwkrTrTMP+IjNJG+NCJ46 y88anBErFijvWb3BINpeTM/dux7DmuoaolGx7lquFu+i0L8UfFFjYG7UU+NZscim KE4j0tJz8jm5ksN4iwaj3RIkGKc1zJtRyoPny3j1blOtm8aTtujRJB7/Gx2QefZR 1Z13RaIzk1tKdY0JxAmPpGkaRY99MQahx96iBsk2u4rlypcxmVr9aQ1Madp7Pc6Y pBcX9jZwLf75cj6CAK93YSjFF3j/x4QM8jSupLCu5tyin6YZ4sRaZa6sy52byk2v zes7i83l5g3+JEKv5oZVwjD5SFBu02UPbnMGSxKQitgz4Zej3qMIq5BxgII2kHZV jwXrNEx4trNegEcoqwFX5xA0FMUr1/g3Cr4+rZBoUramj80cBhzbBdUkhyWd3eey j2EOuAG3pgUD5Wv9SyojlbHBwmSAcBEtr3vqJpTjWQS6AyEmdKNvzh/8JCH1h7UM fBo4+LIEylzmZXbqDrZNwXh31tELoTCR9Ur3pTCEO3Yfg9npTLWmvKs+tAgO/282 IOjZE0N/ZtzPJ6Cgr+2efBGd+id81HXh+H8gWo35Dyx3EH2k44FHwQ3rW2NKOVzo 10eSbswYpjk3gi/6GxwC0lDqFi4Bk6ILvC6roqTghixBf7xThfY= =L5HS -----END PGP SIGNATURE----- Merge tag 'kvmarm-fixes-6.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD KVM/arm64 fixes for 6.14, take #2 - Large set of fixes for vector handling, specially in the interactions between host and guest state. This fixes a number of bugs affecting actual deployments, and greatly simplifies the FP/SIMD/SVE handling. Thanks to Mark Rutland for dealing with this thankless task. - Fix an ugly race between vcpu and vgic creation/init, resulting in unexpected behaviours. - Fix use of kernel VAs at EL2 when emulating timers with nVHE. - Small set of pKVM improvements and cleanups. |